Add GPIO line names on module level. Those are all GPIOs which a user
might use on his custom carrier board. If more meaningful names are
available on the carrier board, the user can overwrite the line names
in the carrier board level device tree.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix names of extra pingroup node and property for gpio bus recovery.
Without the change i2c2 is not functional.
Fixes: 56f0df6b6b ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Drop Colibri V1.1 device tree, this is just a duplicate of Colibri V1.0
with the possibility to use SD cards in UHS mode if the carrier board
does not have 3.3V pull up resistor.
The dedicated device tree kept the feature switched of by setting
the no-1-8-v property and thus does not offer anything different
than what the regular device tree does.
Thus drop the dedicated device tree and merge the preparation to
allow enabling the feature should a carrier without pull ups
be used into the regular device tree.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reuse the generic swiotlb initialization for xen-swiotlb. For ARM/ARM64
this works trivially, while for x86 xen_swiotlb_fixup needs to be passed
as the remap argument to swiotlb_init_remap/swiotlb_init_late.
Note that the lower bound of the swiotlb size is changed to the smaller
IO_TLB_MIN_SLABS based value with this patch, but that is fine as the
2MB value used in Xen before was just an optimization and is not the
hard lower bound.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Pass a boolean flag to indicate if swiotlb needs to be enabled based on
the addressing needs, and replace the verbose argument with a set of
flags, including one to force enable bounce buffering.
Note that this patch removes the possibility to force xen-swiotlb use
with the swiotlb=force parameter on the command line on x86 (arm and
arm64 never supported that), but this interface will be restored shortly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
It used to be that Linux enabled swiotlb-xen when running a dom0 on ARM.
Since f5079a9a2a "xen/arm: introduce XENFEAT_direct_mapped and
XENFEAT_not_direct_mapped", Linux detects whether to enable or disable
swiotlb-xen based on the new feature flags: XENFEAT_direct_mapped and
XENFEAT_not_direct_mapped.
However, there is still a leftover xen_initial_domain() check in
xen_create_contiguous_region. Remove the check as
xen_create_contiguous_region is only called by swiotlb-xen during
initialization. If xen_create_contiguous_region is called, we know Linux
is running 1:1 mapped so there is no need for additional checks.
Also update the in-code comment.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Disable gmac0 which is not connected to any switch MAC. Enable port@8 of
the Broadcom switch which is connected to gmac2.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
AT91 fixes#1 for 5.18:
Only DT fixes. They cover syntax issues as well as features:
- fix dtschema check warnings for DMA channel entries, boolean
properties and flash names
- sam9g20ek audio clock and regulator description
- sama5d[34]_xplained SPI pinctrl
- align DT with hardware subtleties on sama7g5ek
* tag 'at91-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
ARM: dts: at91: sama7g5: Swap `rx` and `tx` for `i2c` nodes
Link: https://lore.kernel.org/r/20220414143318.26363-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Gemini defconfig needs to be updated due to DSA driver
Kconfig changes in the v5.18 merge window:
CONFIG_NET_DSA_REALTEK_SMI is now behind
CONFIG_NET_DSA_REALTEK and the desired DSA switch need
to be selected explicitly with
CONFIG_NET_DSA_REALTEK_RTL8366RB.
Take this opportunity to update some other minor config
options:
- CONFIG_MARVELL_PHY moved around because of Kconfig
changes.
- CONFIG_SENSORS_DRIVETEMP should be selected since is
regulates the system critical alert temperature on
some devices, which is nice if it is handled even
if initramfs or root fails to mount.
Fixes: 319a70a5fe ("net: dsa: realtek-smi: move to subdirectory")
Fixes: 765c39a4fa ("net: dsa: realtek: convert subdrivers into modules")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Defconfig updates for kernel v5.18:
- Refresh defconfig with new and moved options
- Add some new hardware drivers
- Activate battery charging
* tag 'ux500-defconfig-soc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: config: u8500: Re-enable AB8500 battery charging
ARM: config: u8500: Add some common hardware
ARM: config: Refresh U8500 defconfig
Link: https://lore.kernel.org/r/CACRpkdY+_Go4XNzOh+Rvc24QBnUud2k-S7VQuaH5d-j71_dJog@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the PN544 NFC chip mounted on some of the Codina models
numbered GT-I8160P. The "P" at the end of the product number
indicates that an NFC chip is mounted.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff71 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d79975 ("ARM: dts: am3517-evm: Add support for UI board and Audio")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When adding support for TI magadc (Magnetic Stripe Reader and ADC), the
MFD driver common to the touchscreen and the ADC got updated to ease the
insertion of a new DT node for the ADC, with its own compatible, clocks,
etc. Commit 235a96e92c ("mfd: ti_am335x_tscadc: Don't search the tree
for our clock") removed one compatible specific information which was
the clock name, because the clock was looked up from scratch in the DT
while this hardware block was only fed by a single clock, already
defined and properly filled in the DT.
Problem is, this change was only validated with an am437x-based board,
where the clocks are effectively correctly defined and referenced. But
on am33xx, the ADC clock is also correctly defined but is not referenced
with a clock phandle as it ought to be.
The touchscreen bindings clearly state that the clocks/clock-names
properties are mandatory, but they have been forgotten in one DTSI. This
was probably not noticed in the first place because of the clock
actually existing and the clk_get() call going through all the tree
anyway.
Add the missing clock phandles in the am33xx touchscreen description.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Fixes: 235a96e92c ("mfd: ti_am335x_tscadc: Don't search the tree for our clock")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <20220314163445.79807-1-miquel.raynal@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d83 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
Fixes: bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all gpios")
Depends-on: 5c8b498529 ("ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name")
Reported-by: Ajay Kathat <ajay.kathat@microchip.com>
Co-developed-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Ajay Kathat <ajay.kathat@microchip.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-2-claudiu.beznea@microchip.com
The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC and is expected to be set to 12MHz. Previously
this was mapped using pre-common clock API calls in the audio machine
driver but the conversion to the common clock framework broke that so
describe things in the DT instead.
Fixes: ff78a189b0 ("ARM: at91: remove old at91-specific clock driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220404102806.581374-2-broonie@kernel.org
