The MT7622 device tree never bothered to specify the number of virtual DMA
channels for the HSDMA controller, always falling back to the default value of
3. Make this value explicit, in order to avoid the following dmesg notification:
mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/r/20220429084225.298213-1-rsalvaterra@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Visconti device tree updates for 5.19
- Update the clock providers for PCIe host controller
- Update the clock providers for ethernet device
- Update the clock providers for SPI
- Update the clock providers for watchdog timer
- Update the clock providers for I2C
- Update the clock providers for UART
- Add clock controller support for TMPV7708
* tag 'visconti-arm-dt-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti:
arm64: dts: visconti: Update the clock providers for PCIe host controller
arm64: dts: visconti: Update the clock providers for ethernet device
arm64: dts: visconti: Update the clock providers for SPI
arm64: dts: visconti: Update the clock providers for watchdog timer
arm64: dts: visconti: Update the clock providers for I2C
arm64: dts: visconti: Update the clock providers for UART
arm64: dts: visconti: Add clock controller support for TMPV7708
Link: https://lore.kernel.org/r/TYWPR01MB94201E842A2F8E5E9EBF740D92C99@TYWPR01MB9420.jpnprd01.prod.outlook.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New peripherals supported on rk356x: sfc, usb3, sata and
the video-decoder on rk3328.
RK3399 received some improvements and nodes for the memory controller.
Additional peripherals for PineNote, Gru and BananaPi-R2-Pro.
New boards are the Firefly Station M2, Pine64 SoQuartz SOM and
Quartz64 model B as well as the Radxa Rock3 model A.
* tag 'v5.19-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (32 commits)
arm64: dts: rockchip: enable otg/drd operation of usb_host0_xhci in rk356x
arm64: dts: rockchip: rename HDMI ref clock to 'ref' on rk3399
arm64: dts: rockchip: add dts for Firefly Station M2 rk3566
arm64: dts: rockchip: add SoQuartz CM4IO dts
arm64: dts: rockchip: add Pine64 Quartz64-B device tree
dt-bindings: arm: rockchip: Add Firefly Station M2
dt-bindings: arm: rockchip: Add Pine64 SoQuartz SoM
dt-bindings: arm: rockchip: Add Pine64 Quartz64 Model B
arm64: dts: rockchip: enable usb hub on the radxa rock3 model a
arm64: dts: rockchip: add usb3 support to the radxa rock3 model a
arm64: dts: rockchip: add rk356x sfc support
arm64: dts: rockchip: Add USB and TCPC to rk3566-pinenote
arm64: dts: rockchip: Add accelerometer to rk3566-pinenote
arm64: dts: rockchip: add an input enable pinconf to rk3399
arm64: dts: rockchip: Add vdec support for RK3328
arm64: dts: rockchip: Rename vdec_mmu node for RK3328
arm64: dts: rockchip: Enable dmc and dfi nodes on gru
arm64: dts: rockchip: Add dfi and dmc nodes to rk3399
arm64: dts: rockchip: add clocks property to cru nodes rk3399
arm64: dts: rockchip: use generic node name for pmucru on rk3399
...
Link: https://lore.kernel.org/r/7748558.DvuYhMxLoT@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes for the mass-production version of BananaPi R2-Pro.
The mass market version received some changes compared to
preproduction versions and especially the io-domain setting
could affect the lifespan of the board if the wrong dt
gets booted on it.
* tag 'v5.18-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add gmac1 and change network settings of bpi-r2-pro
arm64: dts: rockchip: Change io-domains of bpi-r2-pro
Link: https://lore.kernel.org/r/2300256.NG923GbCHz@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree update for 5.19:
- New board support: Engicam i.Core MX8M Plus SoM and EDIMM2.2 Starter
Kit, Toradex Verdin i.MX8M Plus devices, Data Modul i.MX8M Mini eDM SBC,
Verdin based MX8Menlo, 8MNANOD3L EVK, i.MX8M Plus Gateworks GW7400.
- Enable RTS-CTS on UART3 for imx8mm-beacon and imx8mn-beacon boards.
- Enable HS400-ES support for i.MX8MN and i.MX8MP uSDHC devices by
updating the compatible.
- A few updates on imx8mq-librem5 to increase boost regulation
current, add panel compatible for r4 ("Evergreen") revision and volume
buttons a wakeup source.
- Clean up vendor specific 'fsl,uart-has-rtscts' property by using
standard 'uart-has-rtscts'.
- Add GPC, GPU, MEDIAMIX, and HSIO power domains for i.MX8M Plus SoC.
- A series from Marcel Ziswiler to improve imx8mm-verdin support,
including cosmetic changes and functional improvements like SD1 sleep
pinctrl and fully validated IOMUX configuration.
- Add PWM polarity inversion support for i.MX8 SoCs.
- A couple of changes from Michael Walle to update PMIC output names and
min/max voltages for imx8mn-evk board.
- A series from Tim Harvey to improve imx8mm-venice boards, add missing
uart-has-rtscts property to UARTs, clock-names to pcie_phy, and
vdd_5p0 ADC channel.
- Add VPU codec devices for i.MX8QXP SoC.
- Other small and random changes.
* tag 'imx-dt64-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (65 commits)
arm64: dt: imx8mp: support pwm polarity inversion
arm64: dt: imx8mn: support pwm polarity inversion
arm64: dt: imx8mm: support pwm polarity inversion
arm64: dt: imx8mq: support pwm polarity inversion
arm64: dts: imx8mm-venice-gw7901: remove unnecessary cpu temp override
arm64: dts: imx8mm-venice-gw7902: add vdd_5p0 ADC channel
arm64: dts: imx8m*venice: add missing clock-names to pcie_phy
arm64: dts: imx8mm-venice-gw7902: fix pcie bindings
arm64: dts: freescale: reduce the interrup-map-mask
arm64: dts: imx8mn-beacon: Enable RTS-CTS on UART3
arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3
arm64: dts: imx8mm: Use 100 kHz I2C2 on Data Modul i.MX8M Mini eDM SBC
arm64: dts: imx8mm: Disable USB2 OC on Data Modul i.MX8M Mini eDM SBC
arm64: dts: imx8mm: Add CPLD on MX8Menlo board
arm64: dts: imx8mq-kontron-pitx-imx8m: Use the standard 'uart-has-rtscts'
arm64: dts: imx8mp-verdin: Use the standard 'uart-has-rtscts'
arm64: dts: imx8mp: Add MEDIA_BLK_CTRL
arm64: dts: imx8mp: Add MEDIAMIX power domains
arm64: dts: imx8mp: add HSIO power-domains
arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit
...
Link: https://lore.kernel.org/r/20220508033843.2773685-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DT updates for v5.19
This adds MDIO bus description on the IPQ6018 platform.
On MSM8916 the BAM-DMUX WWAN network device is added and the Huawei
Ascend G7 gains sound card definition and clarified installation
instructions.
MSM8992 and MSM8994 continues to be worked on, gaining multimedia clock
controller, on-chip memory, watchdog and various cleanup changes. The
Xiaomi Mi 4C gains CPU regulators and fixes to the framebuffer
definition, while Huawei Nexus 6P gains eMMC support.
On MSM8996 the modem and sensor remtoeprocs are added and enabled in the
Dragonboard 820c and the Xiaomi devices.
On MSM8998 a few newly added clocks related to the sensor subsystem bus
are marked as protected by default and the OnePlus devices gains NFC.
The SC7180 platform and devices thereon are further polished and
limozeen moves to using edp-panel for EDID-based detection, over
statically defined panels.
On SC7280 GPI DMA, WiFi remoteproc and network device, LPASS audio
clocks, resets for SDCC controllers and a new CRD revision are added. A
supply glitch on the PCIe power and a current leak for Bluetooth during
suspend are corrected. The Herobrine board gains eDP support and the IDP
gains backlight. USB is marked wakeup capable.
On SDM845 the IPA, WLED based backlight and second WiFi channel are
enabled for Xiaomi Pocophone F1, the firmware name is modified to not
conflict with other boards. On RB3 the CAN bus controller is added and
the WiFi calibration variant is defined to allow adding the board's
calibration information into linux-firmware.
SM6350 gains I2C busses, UFS and WiFi support, and the numbering of
uart9 is corrected.
On SM7225 and the Fairphone 4 UFS, WiFi and haptics are enabled.
On SM8150 PCIe, Ethernet and uSD card support is added, and enabled for
the SA8155p ADP board. The PDC interrupt controller is also added and
described as wakup interrupt parent for TLMM.
Camera subsystem and control interface are defined for SM8250. On the
Sony Xperia 1 II the audio amplifiers are enabled.
On SM8350 GPI DMA engines are added and linked to the I2C and SPI
serial engines. Surface Duo 2 gains battery charger support.
On SM8450 the two PCIe controller/PHYs are enabled, GPI DMA and QUP
serial engine instances are added. Remoteproc instances are enabled on
SM8450 HDK.
Last, but not least, a number of DeviceTree validation errors across
various boards are corrected.
* tag 'qcom-arm64-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (150 commits)
arm64: dts: qcom: Only include sc7180.dtsi in sc7180-trogdor.dtsi
arm64: dts: qcom: sc7180-trogdor: Simplify spi0/spi6 labeling
arm64: dts: qcom: sc7180-trogdor: Simplify trackpad enabling
arm64: dts: qcom: sc7280: eDP for herobrine boards
arm64: dts: qcom: sa8155p-adp: Disable multiple Tx and Rx queues for ethernet IP
arm64: dts: qcom: sm8150: Fix iommu sid value for SDC2 controller
arm64: dts: qcom: sm8350-duo2: enable battery charger
arm64: dts: qcom: Enable pm8350c pwm for sc7280-idp2
arm64: dts: qcom: pm8350c: Add pwm support
arm64: dts: qcom: sc7280-qcard: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7280-idp: Configure CTS pin to bias-bus-hold for bluetooth
arm64: dts: qcom: sc7180: Remove ipa interconnect node
arm64: dts: qcom: sc7280-idp: Enable GPI DMAs
arm64: dts: qcom: sc7280: Add GENI I2C/SPI DMA channels
arm64: dts: qcom: sc7280: Add GPI DMAengines
arm64: dts: qcom: sm8450: Fix qmp phy node (use phy@ instead of lanes@)
arm64: dts: qcom: db845c: Add support for MCP2517FD
arm64: dts: qcom: qrb5165-rb5: Fix can-clock node name
arm64: dts: qcom: sc7280: Add SAR sensors to herobrine crd
arm64: dts: qcom: sm8250: camss: Add CCI definitions
...
Link: https://lore.kernel.org/r/20220509204451.325675-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DT fixes for v5.18
This disables the two Soundwire controllers as well as rx and tx macros
by default on the SM8250 platform to avoid crashes on devices where
these aren't available.
* tag 'qcom-arm64-fixes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sm8250: don't enable rx/tx macro by default
Link: https://lore.kernel.org/r/20220509152310.306179-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Espressobin Ultra has a front panel USB3.0 Type-A port which works
just fine so enable it.
I dont see a reason why it was disabled in the first place anyway.
Fixes: 3404fe15a6 ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Both the Topaz switch and 88E1512 PHY have their reset and interrupts
connected to the SoC.
So, define the Topaz and 88E1512 reset pins in the DTS.
Defining the interrupt pins wont work as both the 88E1512 and the
Topaz switch uses active LOW IRQ signals but the A37xx GPIO controller
only supports edge triggers.
88E1512 would require special setup anyway as its INT pin is shared with
the LED2 and you first need to configure it as INT.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
SPI config for the SPI-NOR is incorrect and completely breaking
reading/writing to the onboard SPI-NOR.
SPI-NOR is connected in the single(x1) IO mode and not in the quad
(x4) mode.
Also, there is no need to override the max frequency from the DTSI
as the mx25u3235f that is used supports 104Mhz.
Fixes: 3404fe15a6 ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
uDPU has a pair of NCT375 temperature sensors, which are TMP75C compatible
as far as the driver is concerned.
The current LM75 compatible worked as all of the LM75 compatible sensors
are backwards compatible with the original part, but it meant that lower
resolution and incorrect sample rate was being used.
The "lm75" compatible has been deprecated anyway and is meant as fallback
in order to keep older DTS-es working.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Partition currently called "uboot" does not only contain U-boot, but
rather it contains TF-A, U-boot and U-boot environment.
So, to avoid accidentally deleting the U-boot environment which is
located at 0x180000 split the partition.
"uboot" is not the correct name as you can't boot these boards with U-boot
only, TF-A must be present as well, so rename the "uboot" partition to
"firmware".
While we are here, describe the NOR node as "spi-flash@0" instead of
"m25p80@0" which is the old SPI-NOR driver name.
This won't break booting for existing devices as the SoC-s BootROM is not
partition aware at all, it will simply try booting from 0x0 of the
boot device that is set by bootstrap pins.
This will however prevent accidental or automated flashing of just U-boot
to the partition.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
arm64: tegra: Device tree changes for v5.19-rc1
This adds some improvements on Tegra234 (QSPI, CCPLEX), improves the
SDMMC clock speed on Tegra194 and adds the ASRC audio block on various
chip generations. Memory controller channels are also added on Tegra186
and later and the missing DFLL reset is added for Tegra210.
* tag 'tegra-for-5.19-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add missing DFLL reset on Tegra210
arm64: tegra: Add memory controller channels
arm64: tegra: Enable ASRC on various platforms
arm64: tegra: Add ASRC device on Tegra186 and later
arm64: tegra: Update PWM fan node name
arm64: tegra: Add node for Tegra234 CCPLEX cluster
arm64: tegra: Add QSPI controllers on Tegra234
arm64: tegra: Update SDMMC1/3 clock source for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Renesas ARM DT updates for v5.19 (take two)
- I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and
thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK
development board,
- Initial support for the R-Car V4H SoC and the Renesas White Hawk
development board stack,
- DMA, RTC, and USB support for the RZ/N1D SoC,
- Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit
Board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits)
arm64: dts: renesas: Add initial device tree for RZ/V2M EVK
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY
ARM: dts: r9a06g032: Add USB PHY DT support
ARM: dts: r9a06g032: Add internal PCI bridge node
ARM: dts: r9a06g032: Describe the RTC
arm64: dts: renesas: Add interrupt-names to CANFD nodes
arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
arm64: dts: renesas: r9a07g043: Add TSU node
arm64: dts: renesas: r9a07g043: Add OPP table
arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes
arm64: dts: renesas: r9a07g054: Fix external clk node names
arm64: dts: renesas: r9a07g044: Fix external clk node names
ARM: dts: r9a06g032: Fix the NAND controller node
ARM: dts: r9a06g032: Fill the UART DMA properties
ARM: dts: r9a06g032: Describe the DMA router
ARM: dts: r9a06g032: Add the two DMA nodes
arm64: dts: renesas: Remove empty rgb output endpoints
...
Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor cleanup of ARM64 DTS for v5.19
Align SPI NOR node names and freq-table-hz to DT schema. Drop
unused/undocumented dma-channels/dma-requests.
* tag 'dt64-cleanup-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: broadcom: drop useless 'dma-channels/requests' properties
arm64: dts: stratix10/agilex: drop useless 'dma-channels/requests' properties
arm64: dts: marvell: align SPI NOR node name with dtschema
arm64: dts: microchip: align SPI NOR node name with dtschema
arm64: dts: hisilicon: align 'freq-table-hz' with dtschema in UFS
Link: https://lore.kernel.org/r/20220506081438.149192-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SoC is always present on sc7180-trogdor.dtsi and thus we should
include it in the "generic" dtsi file for trogdor. Previously we had
removed it from there because we had to do the spi6/spi0 swizzle, so
each trogdor variant board had to include sc7180.dtsi and then
sc7180-trogdor.dtsi so that the latter dtsi file could modify the right
spi bus for EC and H1 properties that are common to all trogdor boards.
Now that we're done with that we can replace sc7180.dtsi includes with
sc7180-trogdor.dtsi and include sc7180.dtsi in sc7180-trogdor.dtsi as
was originally intended. We still need to include sc7180-trogdor.dtsi
before the bridge dtsi files though because those rely on the panel
label.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-4-swboyd@chromium.org
We had to do this spi0/spi6 flip-flop on trogdor-r0 because the spi
buses got swizzled between r0 and r1. The swizzle stopped after r1, but
we kept this around to support either hardware possibility and to keep
trogdor-r0 working.
trogdor-r0 isn't supported upstream, so this swizzle is not doing
anything besides making a pattern that others tryt to copy for the EC and
H1 nodes. Let's remove it and simplify the dts files.
Cc: "Joseph S. Barrera III" <joebar@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427020339.360855-3-swboyd@chromium.org
Add eDP support to herobrine boards, splitting up amongst the
different files as makes sense. Rationale for the current split of
things:
* The eDP connector itself is on qcard. However, not all devices with
a qcard will use an eDP panel. Some might use MIPI and, presumably,
someone could build a device with qcard that had no display at all.
* The qcard provides a PWM for backlight that goes to the eDP
connector. This PWM is also provided to the board and it's expected
that it would be used as the backlight PWM even for herobrine
devices with MIPI displays.
* It's currently assumed that all herobrine boards will have some sort
of display, either MIPI or eDP (but not both).
* We will assume herobrine-rev1 has eDP. The schematics allow for a
MIPI panel to be hooked up but, aside from some testing, nobody is
doing this and most boards don't have all the parts stuffed for
it. The two panels would also share a PWM for backlight, which is
weird.
* herobrine-villager and herobrine-hoglin (crd) also have eDP.
* herobrine-hoglin (crd) has slightly different regulator setup for
the backlight. It's expected that this is unique to this board. See
comments in the dts file.
* There are some regulators that are defined in the qcard schematic
but provided by the board like "vreg_edp_bl" and
"vreg_edp_3p3". While we could put references to these regulators
straight in the qcard.dtsi file, this would force someone using
qcard that didn't provide those regulators to provide a dummy or do
an ugly /delete-node/. Instead, we'll add references in
herobrine.dtsi.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220426124053.v2.1.Iedd71976a78d53c301ce0134832de95a989c9195@changeid
