Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
together in older HW revisions. Later ISB_IN2 was removed. Software should
still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the prototype had the SATA interface. There are no existing products
with SATA interface and no plans to add any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function of DISP0_DAT9 is dependent on hardware revision of two
particular variants. This setting should be done by the bootloader anyway,
and is not needed in the kernel, so remove it from the DT.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add some missing names and remove names to pins that have never been used
and/or are not present on any hardware.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While there are LEDs connected on some variants on GPIO4 pins 16 and 17,
those are not the debug LEDs that should be visible to user-space.
It should be the same as in imx6dl-victgo.dtsi.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The names should be consistent with the names in imx6dl-victgo.dts
This patch is preparation to unify vicut1 and victgo DTs.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the very first prototypes had PCIe and there are no plant to add it
in the future.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unify nON_SWITCH pinctrl configuration with imx6dl-victgo.dts.
This patch is a preparation to reduce duplicated code between vicut1 and
victgo.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only the first prototypes had a TiWi module. There is no publicly available
hardware where this module is fitted and there are no plan to produce
any.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
Fixes: c2e4987e0e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dts for ARMv7 based broadband SoC BCM47622. bcm47622.dtsi is the
SoC description dts header and bcm947622.dts is a simple dts file for
Broadcom BCM947622 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Samsung DTS ARM changes for v5.19
1. Several DT schema related changes to make DTBs passing schema checks:
EHCI/OHCI/DMA/Ethernet node names, DMA channels order, USB-like
compatibles.
2. Add specific compatibles to Multi Core Timer to allow stricter DT
schema matching.
3. Cleanup from deprecated bindings:
- Remove deprecated unit-address workaround for Exynos5422 Odroid XU3
LPDDR3 memory timings.
- Do not use unit-address (and SFR region) in Exynos5250 MIPI phy in
favor of syscon node (unit-address deprecated in 2016).
- Use standard generic PHYs for EHCI/OHCI device in S5PV210.
4. Fix inverted SPI CS (thus blank panel) on S5PV210 Aries boards.
5. Correct Bluetooth interupt name on S5PV210 Aries boards.
* tag 'samsung-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: align DMA channels with dtschema
ARM: dts: s5pv210: Adjust DMA node names to match spec
ARM: dts: s5pv210: Adjust memory reg entries to match spec
ARM: dts: s5pv210: Correct interrupt name for bluetooth in Aries
ARM: dts: s5pv210: Remove spi-cs-high on panel in Aries
ARM: dts: s5pv210: Use standard arrays of generic PHYs for EHCI/OHCI device
ARM: dts: s5pv210: align EHCI/OHCI nodes with dtschema
ARM: dts: exynos: align EHCI/OHCI nodes with dtschema on Exynos4
ARM: dts: exynos: drop deprecated SFR region from MIPI phy
ARM: dts: exynos: add a specific compatible to MCT
ARM: dts: exynos: remove deprecated unit address for LPDDR3 timings on Odroid
ARM: dts: exynos: fix compatible strings for Ethernet USB devices
ARM: dts: exynos: fix ethernet node name for different odroid boards
Link: https://lore.kernel.org/r/20220420072152.11696-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes for omaps
Few regression fixes for omap variants. These mostly fix issues related to
warnings added for system suspend, and some devicetree issues:
- Make ti-sysc driver quirks for gpt12 timer omap3 specific to fix
timer clock disabling for am335x system suspend
- Fix new system suspend warning for dra7 vpe caused by trying to
use register bits not wired for vpe
- Fix mmc boot order for omap3-gta04 that has no mmc2 or 3 wired
- Add missing touchscreen properties for am3
- Fix pin muxing for logicpd-som-lv and am3517-evm to not depend on
earlier bootloader versions
- Fix refcount leak for omap_gic_of_init
* tag 'omap-for-v5.18/fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: dra7: Fix suspend warning for vpe powerdomain
bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific
ARM: OMAP2+: Fix refcount leak in omap_gic_of_init
iommu/omap: Fix regression in probe for NULL pointer dereference
Link: https://lore.kernel.org/r/pull-1650543308-836725@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The node name of Ethernet controller should be "ethernet" instead of
"usbether" as required by Ethernet controller devicetree schema:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
This patch can potentially affect boot loaders patching against full
node path instead of using device aliases.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Message-Id: <20220216074927.3619425-8-o.rempel@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
