So far, the binding and driver have relied on the fact that the H6
clocks are both a prefix and a subset of the R40 clocks. This allows
them to share the clocks/clock-names items and the clock-output-names
order between the hardware variants.
However, the D1 hardware has TCON TV0 and DSI, but no TCON TV1. This
cannot be supported by the existing scheme because it puts a gap in the
middle of the item lists. To prepare for adding D1 support, use separate
lists for variants with different combinations of clocks.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-2-samuel@sholland.org
The ARASAN MMC controller on Keystone 3 class of devices needs the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 3794c54264 ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where SDCD line is not connected, adding
"ti,fails-without-test-cd" in the DT node helps to indicate the
controller, that the SDCD line has been pulled down, using the TESTCD bit.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220425063120.10135-2-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHC controller in the imx8mn and imx8mp have the same controller
as the imx8mm which is slightly different than that of the imx7d.
Using the fallback of the imx8mm enables the controllers to support
HS400-ES which is not available on the imx7d. After discussion with NXP,
it turns out that the imx8qm should fall back to the imx8qxp, because
those have some additional flags not present in the imx8mm.
Mark the current state of the fallbacks as deprecated, and add the
proper fallbacks so in the future, the deprecated combination can be
removed and prevent any future devices from using the wrong fallback.
Suggested-by: haibo.chen@nxp.com
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220410193544.1745684-1-aford173@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert the marvell,xenon-sdhci binding to JSON schema. Currently the
in-tree dts files don't validate because they use sdhci@ instead of mmc@
as required by the generic mmc-controller schema.
The compatible "marvell,sdhci-xenon" was not documented in the old
binding but it accompanies the of "marvell,armada-3700-sdhci" in the
armada-37xx SoC dtsi so this combination is added to the new binding
document.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220329220544.2132135-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the firmware subsystem to support a persistent sysfs interface that
userspace may use to initiate a firmware update. For example, FPGA based
PCIe cards load firmware and FPGA images from local FLASH when the card
boots. The images in FLASH may be updated with new images provided by the
user at his/her convenience.
A device driver may call firmware_upload_register() to expose persistent
"loading" and "data" sysfs files. These files are used in the same way as
the fallback sysfs "loading" and "data" files. When 0 is written to
"loading" to complete the write of firmware data, the data is transferred
to the lower-level driver using pre-registered call-back functions. The
data transfer is done in the context of a kernel worker thread.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-5-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra CPU COMPLEX CLUSTER area contains memory-mapped
registers that initiate CPU frequency/voltage transitions.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The indentation was wrong, causing the documentation build to
fail with:
Sphinx parallel build error:
docutils.utils.SystemMessagePropagation: <system_message level="3" line="1202" source="/home/hans/work/src/v4l/media-git/Documentation/media/userspace-api/v4l/ext-ctrls-codec.rst"
type="ERROR"><paragraph>Error parsing content block for the "flat-table" directive: two-level bullet list expected, but row 1 does not contain a second-level bullet list.</paragraph><literal_block
xml:space="preserve">.. flat-table::
:header-rows: 0
:stub-columns: 0
* - ``V4L2_MPEG_VIDEO_INTRA_REFRESH_PERIOD_TYPE_RANDOM``
- The whole frame is completely refreshed randomly
after the specified period.
* - ``V4L2_MPEG_VIDEO_INTRA_REFRESH_PERIOD_TYPE_CYCLIC``
- The whole frame MBs are completely refreshed in cyclic order
after the specified period.
</literal_block></system_message>
make[1]: *** [Documentation/Makefile:96: htmldocs] Error 2
make: *** [Makefile:1678: htmldocs] Error 2
Link: https://lore.kernel.org/linux-media/62b53cbb-f3e2-ed8a-bba2-3f4145d9b8db@xs4all.nl
Fixes: fcbc4acf8b ("media: v4l2-ctrls: Add intra-refresh type control")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Let's update the TI timer binding to use yaml. As this binding is specific
to the TI dual-mode timers also known as dm-timers, let's use file name
ti,timer-dm.yaml to avoid confusion with other timers.
We add checks for the deprecated ti,hwmods property as done for other TI
device driver bindings earlier.
We also correct the issue with the old binding that was out of date for
several properties.
The am43 related timers are undocumented, but compatible with the am3
timers. Let's add the am43 timers too.
The dm814 and dm816 timers are missing, let's add them.
Some timers on some SoCs are dual mapped, like the ABE timers on omap4
and 5. The reg property maxItems must be updated to 2.
The timer clocks can be managed by the parent interconnect target module
with no clocks assigned for the timer node. And in some cases, the SoC may
need to configure additional system clock for the timer in addition to the
functional clock.
The clock names are optional and not specific to the comptible property.
For example, dra7 timers on l3 interconnect do not need clock-names, while
the timers on dra7 l4 interconnect need them with both being compatible
with ti,omap5430-timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220414085807.7389-2-tony@atomide.com
Convert the fsl,layerscape-dcfg binding to the new YAML format.
In the device trees, the device node always have a "syscon"
compatible, which wasn't mentioned in the previous binding.
One thing added here, compared to the original binding is the clock
controller subnode of the LS1028A SoC and its "simple-mfd" compatible as
used in arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi as well as the
little-endian and big-endian properties.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220425140433.33936-1-michael@walle.cc
Typical GPIO lines like enable, powerdown, reset or wakeup are not
documented as common, which leads to new variations of these (e.g.
pwdn-gpios). Add a common schema which serves also as a documentation
for preferred naming.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Pull f2fs fixes from Jaegeuk Kim:
"This includes major bug fixes introduced in 5.18-rc1 and 5.17+:
- Remove obsolete whint_mode (5.18-rc1)
- Fix IO split issue caused by op_flags change in f2fs (5.18-rc1)
- Fix a wrong condition check to detect IO failure loop (5.18-rc1)
- Fix wrong data truncation during roll-forward (5.17+)"
* tag 'f2fs-fix-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: should not truncate blocks during roll-forward recovery
f2fs: fix wrong condition check when failing metapage read
f2fs: keep io_flags to avoid IO split due to different op_flags in two fio holders
f2fs: remove obsolete whint_mode
Fix various kfree() issues related to of_overlay_apply().
- Double kfree() of fdt and tree when init_overlay_changeset()
returns an error.
- free_overlay_changeset() free the root of the unflattened
overlay (variable tree) instead of the memory that contains
the unflattened overlay.
- For the case of a failure during applying an overlay, move kfree()
of new_fdt and overlay_mem into free_overlay_changeset(), which
is called by the function that allocated them.
- For the case of removing an overlay, the kfree() of new_fdt and
overlay_mem remains in free_overlay_changeset().
- Check return value of of_fdt_unflatten_tree() for error instead
of checking the returned value of overlay_root.
- When storing pointers to allocated objects in ovcs, do so as
near to the allocation as possible instead of in deeply layered
function.
More clearly document policy related to lifetime of pointers into
overlay memory.
Double kfree()
Reported-by: Slawomir Stepien <slawomir.stepien@nokia.com>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220420222505.928492-3-frowand.list@gmail.com
Fix the documentation for the hsiphash functions to avoid conflating the
HalfSipHash algorithm with the hsiphash functions, since these functions
actually implement either HalfSipHash or SipHash, and random.c now uses
HalfSipHash (in a very special way) without the hsiphash functions.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The binding and driver duplicated regulator core feature of controlling
regulators with GPIOs (of_parse_cb + ena_gpiod) and created its own
enable-gpios property with multiple GPIOs.
This is a less preferred way, because enable-gpios should enable only one
element, not multiple. It also duplicates existing solution.
Deprecate the original 'enable-gpios' and add per-regulator property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220425072455.27356-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend MDDQ to obtain FW version of line card device and implement
device_info_get() op to fill up the info with that.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the driver to provide per line card info get op to fill-up info,
similar to the "devlink dev info".
Example:
$ devlink lc info pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
lc 8
versions:
fixed:
hw.revision 0
running:
ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.
To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-6-tzimmermann@suse.de
