Fairly straight conversion. The one oddity in the original binding
is that spi-cpha and spi-cpol were not marked as required, but were
in the example. Looking at the datasheet, there isn't any documented
flexibility in the possible SPI modes, so I have moved these to requires.
For spi-max-frequency I have gone the other way. I absolutely agree
that it is good to specify this in the dt-binding, but it's not
strictly required.
As Stefan's email is bouncing I have gone with Michael as maintainer
of this one as it falls under the ADI catch all entry in MAINTAINERS.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Link: https://lore.kernel.org/r/20200909175946.395313-16-jic23@kernel.org
This binding has a few corners that would have been done different today
but hopefully the yaml schema captures the constraints correctly.
The child node names are not constrained hence the fairly open regexp.
I've also documented the defaults for the two references that the
driver seems to use and copied the value descriptions from the header
because I think they should be in the dt-binding itself.
This is part of a general effort to convert all the IIO bindings
over to yaml
Unfortunately I don't have a current address for Markus, so
have put myself as the maintainer for this binding until someone else
steps up!
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200909175946.395313-21-jic23@kernel.org
The ADC in S3C/S5P/Exynos SoCs can be used also for handling touch
screen. In such case the second interrupt is required. This second
interrupt can be anyway provided, even without touch screens. This
fixes dtbs_check warnings like:
arch/arm/boot/dts/s5pv210-aquila.dt.yaml: adc@e1700000: interrupts: [[23], [24]] is too long
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huwei.com>
Link: https://lore.kernel.org/r/20200910161933.9156-1-krzk@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simple device with a simple conversion. Special handling needed
for the max1118 which is the only supported part that has an external
reference voltage.
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Straight forward conversion of this binding for this
current sense amplifier and ADC.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Straight forward conversion for this SPI ADC.
Added limits on spi-max-frequency from datasheet (0.1 to 4.8MHz)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Another wack-a-mole pass of killing off unnecessary 'allOf + $ref'
usage.
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Signed-off-by: Rob Herring <robh@kernel.org>
Fairly simple binding. Most of the changes were filling in information
not previously found in the binding. I dropped the previous explicit
mention of spi-max-frequency as that is covered by the generic SPI
binding.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Convert the textual documentation of Device Tree bindings for the
Ingenic JZ47xx SoCs ADC controller to YAML.
The `interrupts` property is now explicitly listed and marked as
required. While missing from the previous textual documentation, this
property has been used with all the boards which probe this driver.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add documentation for PMIC7 ADC peripheral.
For the PMIC7-type PMICs, ADC peripheral is present in HW for the
following PMICs: PMK8350, PM8350, PM8350b, PMR735a and PMR735b.
Of these, only the ADC peripheral on PMK8350 is exposed directly to SW.
If SW needs to communicate with ADCs on other PMICs, it specifies the
PMIC to PMK8350 through the newly added SID register and communication
between PMK8350 ADC and other PMIC ADCs is carried out through
PBS(Programmable Boot Sequence) at the firmware level.
In addition, add definitions for ADC channels and virtual channel
definitions (combination of ADC channel number and PMIC SID number)
per PMIC, to be used by ADC clients for PMIC7.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver changes for 5.8-rc1
Nothing major, but a lot of new IIO drivers are included in here,
along with other core iio cleanups and changes.
On the staging driver front, again, nothing noticable. No new
deletions or additions, just a ton of tiny cleanups all over the tree
done by a lot of different people. Most coding style, but many actual
real fixes and cleanups that are nice to see.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (618 commits)
staging: rtl8723bs: Use common packet header constants
staging: sm750fb: Add names to proc_setBLANK args
staging: most: usb: init return value in default path of switch/case expression
staging: vchiq: Get rid of VCHIQ_SERVICE_OPENEND callback reason
staging: vchiq: move vchiq_release_message() into vchiq
staging: vchi: Get rid of C++ guards
staging: vchi: Get rid of not implemented function declarations
staging: vchi: Get rid of vchiq_status_to_vchi()
staging: vchi: Get rid of vchi_service_set_option()
staging: vchi: Merge vchi_msg_queue() into vchi_queue_kernel_message()
staging: vchiq: Move copy callback handling into vchiq
staging: vchi: Get rid of vchi_queue_user_message()
staging: vchi: Get rid of vchi_service_destroy()
staging: most: usb: use function sysfs_streq
staging: most: usb: add missing put_device calls
staging: most: usb: use correct error codes
staging: most: usb: replace code to calculate array index
staging: most: usb: don't use error path to exit function on success
staging: most: usb: move allocation of URB out of critical section
staging: most: usb: return 0 instead of variable
...
json-schema versions draft7 and earlier have a weird behavior in that
any keywords combined with a '$ref' are ignored (silently). The correct
form was to put a '$ref' under an 'allOf'. This behavior is now changed
in the 2019-09 json-schema spec and '$ref' can be mixed with other
keywords. The json-schema library doesn't yet support this, but the
tooling now does a fixup for this and either way works.
This has been a constant source of review comments, so let's change this
treewide so everyone copies the simpler syntax.
Scripted with ruamel.yaml with some manual fixups. Some minor whitespace
changes from the script.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Stephen Boyd <sboyd@kernel.org> # clock
Signed-off-by: Rob Herring <robh@kernel.org>
We need the staging fixes in here too, and this resolves a merge issue
with the vt6656 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
