The decision whether to report serdes statistics currently depends on
the cached C_Mode value for the port, read at probe time or updated by
configuration. However, port 4 can be in "automedia" mode when it is
used as a serdes port, meaning it switches between the internal PHY and
the serdes, changing the read-only C_Mode value depending on which
first gains link. Consequently, the C_Mode value read at probe does not
accurately reflect whether the port has the serdes associated with it.
In "net: dsa: mv88e6xxx: add mv88e6352_g2_scratch_port_has_serdes()",
we added a way to read the hardware configuration to determine which
port has the serdes associated with it. Use this to determine which
port reports the serdes statistics.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the mv88e6xxx chip drivers are supplying the supported
interfaces and MAC capabilities, switch the driver to use the generic
phylink validation implementation by removing our own validation
implementations. This causes DSA to call phylink_generic_validate()
on our behalf.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the
Marvell MV88E6xxx DSA switches in preparation to using these for the
validation functionality.
Patch co-authored by Marek.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org> [ fixed 6341 and 6393x ]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the hardware configuration to determine which port is attached
to the serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Waldekranz says:
====================
net: dsa: mv88e6xxx: Improve standalone port isolation
The ideal isolation between standalone ports satisfies two properties:
1. Packets from one standalone port must not be forwarded to any other
port.
2. Packets from a standalone port must be sent to the CPU port.
mv88e6xxx solves (1) by isolating standalone ports using the PVT. Up
to this point though, (2) has not guaranteed; as the ATU is still
consulted, there is a chance that incoming packets never reach the CPU
if its DA has previously been used as the SA of an earlier packet (see
1/5 for more details). This is typically not a problem, except for one
very useful setup in which switch ports are looped in order to run the
bridge kselftests in tools/testing/selftests/net/forwarding. This
series attempts to solve (2).
Ideally, we could simply use the "ForceMap" bit of more modern chips
(Agate and newer) to classify all incoming packets as MGMT. This is
not available on older silicon that is still widely used (Opal Plus
chips like the 6097 for example).
Instead, this series takes a two pronged approach:
1/5: Always clear MapDA on standalone ports to make sure that no ATU
entry can lead packets astray. This solves (2) for single-chip
systems.
2/5: Trivial prep work for 4/5.
3/5: Trivial prep work for 4/5.
4/5: On multi-chip systems though, this is not enough. On the incoming
chip, the packet will be forced out towards the CPU thanks to
1/5, but on any intermediate chips the ATU is still consulted. We
override this behavior by marking the reserved standalone VID (0)
as a policy VID, the DSA ports' VID policy is set to TRAP. This
will cause the packet to be reclassified as MGMT on the first
intermediate chip, after which it's a straight shot towards the
CPU.
Finally, we allow more tests to be run on mv88e6xxx:
5/5: The bridge_vlan{,un}aware suites sets an ageing_time of 10s on
the bridge it creates, but mv88e6xxx has a minimum supported time
of 15s. Allow this time to be overridden in forwarding.config.
With this series in place, mv88e6xxx passes the following kselftest
suites:
- bridge_port_isolation.sh
- bridge_sticky_fdb.sh
- bridge_vlan_aware.sh
- bridge_vlan_unaware.sh
v1 -> v2:
- Wording/spelling (Vladimir)
- Use standard iterator in dsa_switch_upstream_port (Vladimir)
- Limit enabling of VTU port policy to downstream DSA ports (Vladimir)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the ageing timeout that is set on bridges to be customized from
forwarding.config. This allows the tests to be run on hardware which
does not support a 10s timeout (e.g. mv88e6xxx).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VTU entry with policy enabled is used in combination with a port's
VTU policy setting to override normal switching behavior for frames
assigned to the entry's VID.
A typical example is to Treat all frames in a particular VLAN as
control traffic, and trap them to the CPU. In which case the relevant
user port's VTU policy would be set to TRAP.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miroslav Lichvar says:
====================
Virtual PTP clock improvements and fix
v2:
- dropped patch changing initial time of virtual clocks
The first patch fixes an oops when unloading a driver with PTP clock and
enabled virtual clocks.
The other patches add missing features to make synchronization with
virtual clocks work as well as with the physical clock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the physical clock supports cross timestamping (it has the
getcrosststamp() function), provide a wrapper in the virtual clock to
enable cross timestamping.
This adds support for the PTP_SYS_OFFSET_PRECISE ioctl.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the physical clock has the gettimex64() function, provide a
gettimex64() wrapper in the virtual clock to enable more accurate
and stable synchronization.
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the maximum frequency offset of virtual clocks to 50% to enable
faster slewing corrections.
This value cannot be represented as scaled ppm when long has 32 bits,
but that is already the case for other drivers, even those that provide
the adjfine() function, i.e. 32-bit applications are expected to check
for the limit.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unregistering a physical clock which has some virtual clocks,
unregister the virtual clocks with it.
This fixes the following oops, which can be triggered by unloading
a driver providing a PTP clock when it has enabled virtual clocks:
BUG: unable to handle page fault for address: ffffffffc04fc4d8
Oops: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:ptp_vclock_read+0x31/0xb0
Call Trace:
timecounter_read+0xf/0x50
ptp_vclock_refresh+0x2c/0x50
? ptp_clock_release+0x40/0x40
ptp_aux_kworker+0x17/0x30
kthread_worker_fn+0x9b/0x240
? kthread_should_park+0x30/0x30
kthread+0xe2/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
Fixes: 73f37068d5 ("ptp: support ptp physical/virtual clocks conversion")
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to permit a driver to perform "fragmenting" of the
page from within the driver instead of the current model which requires
pre-partitioning the page. The main motivation behind this is to support
use cases where the page will be split up by the driver after DMA instead
of before.
With this change it becomes possible to start using page pool to replace
some of the existing use cases where multiple references were being used
for a single page, but the number needed was unknown as the size could be
dynamic.
For example, with this code it would be possible to do something like
the following to handle allocation:
page = page_pool_alloc_pages();
if (!page)
return NULL;
page_pool_fragment_page(page, DRIVER_PAGECNT_BIAS_MAX);
rx_buf->page = page;
rx_buf->pagecnt_bias = DRIVER_PAGECNT_BIAS_MAX;
Then we would process a received buffer by handling it with:
rx_buf->pagecnt_bias--;
Once the page has been fully consumed we could then flush the remaining
instances with:
if (page_pool_defrag_page(page, rx_buf->pagecnt_bias))
continue;
page_pool_put_defragged_page(pool, page -1, !!budget);
The general idea is that we want to have the ability to allocate a page
with excess fragment count and then trim off the unneeded fragments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Trivial DSA conversions to phylink_generic_validate()
This series converts five DSA drivers to use phylink_generic_validate().
No feedback or testing reports were received from the CFT posting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the xrs700x
family of DSA switches and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
According to commit ee00b24f32 ("net: dsa: add Arrow SpeedChips
XRS700x driver") the switch supports one RMII port and up to three
RGMII ports. This commit assumes that port 0 is the RMII port and the
remainder are RGMII.
This commit also results in the Autoneg bit being set in the ethtool
link modes, which wasn't in the original; if this switch supports
RGMII to a 10/100/1G PHY, then surely we want to allow Autoneg on the
PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the QCA8K
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
In making this change, we bring consistency to the ethtool linkmodes
that phylink's validate step produces, thereby following the expected
behaviour as the phylink documentation has explained. Specifically, the
ethtool 1000baseX_Full capability is now permitted for all interface
modes, as it is a property of the PHY driver whether 1000baseX fiber
connections can be supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the
Microchip KSZ8795 DSA switch and remove the old validate implementation
to allow DSA to use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the bcm_sf2
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII and Reverse MII links is
handled within phylink_generic_validate() in phylink, so there is no
need to make them conditional on the interface mode in the driver.
Thanks to Florian Fainelli for suggesting how to populate the supported
interfaces.
Link: https://lore.kernel.org/r/3b3fed98-0c82-99e9-dc72-09fe01c2bcf3@gmail.com
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the supported interfaces and MAC capabilities for the AR9331
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Miscellaneous changes for 5.18
Patch 1 has some minor cleanup in mptcp_write_options().
Patch 2 moves a rarely-needed branch to optimize mptcp_write_options().
Patch 3 adds a comment explaining which combinations of MPTCP option
headers are expected.
Patch 4 adds a pr_debug() for the MPTCP_RST option.
Patches 5-7 allow setting MPTCP_PM_ADDR_FLAG_FULLMESH with the "set
flags" netlink command. This allows changing the behavior of existing
path manager endpoints. The flag was previously only set at endpoint
creation time. Associated selftests also updated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the fullmesh setting and clearing selftests in
mptcp_join.sh.
Now we can set both backup and fullmesh flags, so avoid using the
words 'backup' and 'bkup'.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the fullmesh flag setting and clearing support in
pm_nl_ctl:
# pm_nl_ctl set ip flags fullmesh
# pm_nl_ctl set ip flags nofullmesh
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the fullmesh flag setting support in pm_netlink.
If the fullmesh flag of the address is changed, remove all the related
subflows, update the fullmesh flag and create subflows again.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch printed out the reset infos, reset_transient and reset_reason,
of MP_RST in mptcp_parse_option() to show that MP_RST is received.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8684 doesn't seem to clearly specify which MPTCP options can be used
together.
Some options are mutually exclusive -- e.g. MP_CAPABLE and MP_JOIN --,
some can be used together -- e.g. DSS + MP_PRIO --, some can but we
prefer not to -- e.g. DSS + ADD_ADDR -- and some have to be used
together at some points -- e.g. MP_FAIL and DSS.
We need to clarify this as a base before allowing other modifications.
For example, does it make sense to send a RM_ADDR with an MPC or MPJ?
This remains open for possible future discussions.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MP_FAIL should be use in very rare cases, either when the TCP RST flag
is set -- with or without an MP_RST -- or with a DSS, see
mptcp_established_options().
Here, we do the same in mptcp_write_options().
Co-developed-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the declarations of ssk and subflow in MP_FAIL and MP_PRIO to the
beginning of the function mptcp_write_options().
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2fd3fb0be1d1 ("kasan, vmalloc: unpoison VM_ALLOC pages
after mapping"), non-VM_ALLOC mappings will be marked as accessible
in __get_vm_area_node() when KASAN is enabled. But now the flag for
ringbuf area is VM_ALLOC, so KASAN will complain out-of-bound access
after vmap() returns. Because the ringbuf area is created by mapping
allocated pages, so use VM_MAP instead.
After the change, info in /proc/vmallocinfo also changes from
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmalloc user
to
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmap user
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: syzbot+5ad567a418794b9b5983@syzkaller.appspotmail.com
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220202060158.6260-1-houtao1@huawei.com
Alex Elder says:
====================
net: ipa: support variable RX buffer size
Specify the size of receive buffers used for RX endpoints in the
configuration data, rather than using 8192 bytes for all of them.
Increase the size of the AP receive buffer for the modem to 32KB.
====================
Link: https://lore.kernel.org/r/20220201153737.601149-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Increase the receive buffer size used for data received from the
modem to 32KB, to improve download performance by allowing much
greater aggregation.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow RX endpoints to have differing receive buffer sizes. Define
the receive buffer size in the configuration data, and use that
rather than IPA_RX_BUFFER_SIZE when configuring the endpoint.
Add verification in ipa_endpoint_data_valid_one() that the receive
buffer specified for AP RX endpoints is both big enough to handle at
least one full packet, and not so big in an aggregating endpoint
that its size can't be represented when programming the hardware.
Move aggr_byte_limit_max() up in "ipa_endpoint.c" so it can be used
earlier in the file without a forward-reference.
Initially we'll just keep the 8KB receive buffer size already in use
for all AP RX endpoints..
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]:
kworker/0:16/14617 is trying to acquire lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
[...]
but task is already holding lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572
The neighbor entry turned to NUD_FAILED state, where __neigh_event_send()
triggered an immediate probe as per commit cd28ca0a3d ("neigh: reduce
arp latency") via neigh_probe() given table lock was held.
One option to fix this situation is to defer the neigh_probe() back to
the neigh_timer_handler() similarly as pre cd28ca0a3d. For the case
of NTF_MANAGED, this deferral is acceptable given this only happens on
actual failure state and regular / expected state is NUD_VALID with the
entry already present.
The fix adds a parameter to __neigh_event_send() in order to communicate
whether immediate probe is allowed or disallowed. Existing call-sites
of neigh_event_send() default as-is to immediate probe. However, the
neigh_managed_work() disables it via use of neigh_event_send_probe().
[0] <TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2956 [inline]
check_deadlock kernel/locking/lockdep.c:2999 [inline]
validate_chain kernel/locking/lockdep.c:3788 [inline]
__lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027
lock_acquire kernel/locking/lockdep.c:5639 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604
__raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline]
_raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334
___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123
__ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
__ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508
ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650
ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742
neigh_probe+0xc2/0x110 net/core/neighbour.c:1040
__neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201
neigh_event_send include/net/neighbour.h:470 [inline]
neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Tested-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220201193942.5055-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_shift_skb_data() might collapse three packets into a larger one.
P_A, P_B, P_C -> P_ABC
Historically, it used a single tcp_skb_can_collapse_to(P_A) call,
because it was enough.
In commit 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions"),
this call was replaced by a call to tcp_skb_can_collapse(P_A, P_B)
But the now needed test over P_C has been missed.
This probably broke MPTCP.
Then later, commit 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
added an extra condition to tcp_skb_can_collapse(), but the missing call
from tcp_shift_skb_data() is also breaking TCP zerocopy, because P_A and P_C
might have different skb_zcopy_pure() status.
Fixes: 8571248411 ("tcp: coalesce/collapse must respect MPTCP extensions")
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220201184640.756716-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Ensure SM_NOTIFY doesn't crash the NFS server host
- Ensure NLM locks are cleaned up after client reboot
- Fix a leak of internal NFSv4 lease information
-----BEGIN PGP SIGNATURE-----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=IC/r
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable bug fixes:
- Ensure SM_NOTIFY doesn't crash the NFS server host
- Ensure NLM locks are cleaned up after client reboot
- Fix a leak of internal NFSv4 lease information"
* tag 'nfsd-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: nfsd4_setclientid_confirm mistakenly expires confirmed client.
lockd: fix failure to cleanup client locks
lockd: fix server crash on reboot of client holding lock
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmH6gtsACgkQnJ2qBz9k
QNkHTggAvFfCBZ11AM3MIQifVrN06q0Aq/xTCR56lbLoqjVbLx+oUAPYk45AgzBJ
9NhYFwPbevLs+c1JrigmTW/i2juZghdfV3CBu6uWvnIDgZbjDwt1RFZ/TMuzG488
Orr12n34J+kaM89BxBPxecFXqGW1bqtIeIUkM6M4OefagVvueRP591GEHRPGk60S
nz90LIZN2fsXrDq6K0EC4LVnMF8VWe7lpW8vHORc/O83KasHFGv1xXJ/Z1ovq9ln
N17pbjFvECyKwIsvQCuKoxa/iutKqiUSQiVyFyN9IryBE5bMKSuv87EP+dKPcP/O
Vmkg2AZRAbL9+M/rhgu4mF0bfhnuJQ==
=uGov
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fanotify fix from Jan Kara:
"Fix stale file descriptor in copy_event_to_user"
* tag 'fsnotify_for_v5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: Fix stale file descriptor in copy_event_to_user()
This kunit update for Linux 5.17-rc3 consists of a single fix to an error
seen on qemu due to a missing import.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPZKym/RZuOCGeA/kCwJExA0NQxwFAmH5reYACgkQCwJExA0N
QxyTlRAA7CYxkE9UjeReUDHWllwI+/hMLqk06Xe+T/uUNlXJTnr7NBLbUI9896Ur
2LB7k+yP1h1tlimQFMH1SfzAQrSUdpwhX+IXN1/3oLgcXYCNeoEUhF7DfGXST1BX
mOd1Qr+GU/yIru7WfpRDxEZgjech9BnDlmuEi10ZF7uYyte49ZbyBIrR4VQjuSvb
SK2iHpdQk8/7TVoE2r6fTJW2n6LcFzlXCOi48jzBdBfSfeo8WFd9EK2DD9Y7PJSM
UjXQBEXGqae2Occu6+qqBZCRMR3sxxo3T7Ak01pAhzgEDDQjuKNFLhQHPti6bgYJ
VbMSaP7onuwIRBVSvoXeOnzjT6ozXXb+C0q406gE4vu71UAxD5E0k6wZuoh5q4xr
MKkACZbsEmylkTq+cQhe8LmdwEN3yhcjZ0cRsqvhSpwnpXVBb4yUSyIyGJesSQkS
JvCxKaCm+wnCyr3xZL+PXK0tfEqTt53wMeVRG0PlMd+zBdxoZo4KbNlX1I2klV9H
Mi5J2mUsyoGFaJp3MOqFNTn3WQ3jFNOFFKlFhlUHzsm72Nth4GnBC1W95QxKNAOG
Peut78LWVdlCcgnN7IPXL1/MZLUVC0WMf7Q6UbMQCZy+dK6RPIzliN5Fipmah2Re
BpH5E0UycoL7NJo8aFhavSm+LbzYa+cFrEVCeXRLDxjjuqRwTso=
=maDS
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"A single fix to an error seen on qemu due to a missing import"
* tag 'linux-kselftest-kunit-fixes-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Import missing importlib.abc
- Fix up group name building on the Intel Thunderbay
- Fix interrupt problems on the Intel Cherryview
- Fix some pin data on the Sunxi H616
- Fix up the CONFIG_PINCTRL_ST Kconfig sort order as noted during
the merge window
- Fix an unexpected interrupt problem on the Intel Sunrisepoint
- Fix a glitch when updating IRQ flags on all Intel pin controllers
- Revert a Zynqmp patch to unify the pin naming, let's find some
better solution
- Fix some error paths in the Broadcom BCM2835 driver
- Fix a Kconfig problem pertaining to the BCM63XX drivers
- Fix the regmap support in the Microchip SGPIO driver
-----BEGIN PGP SIGNATURE-----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=3/r6
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Most interesting and urgent is the Intel stuff affecting Chromebooks
and laptops.
- Fix up group name building on the Intel Thunderbay
- Fix interrupt problems on the Intel Cherryview
- Fix some pin data on the Sunxi H616
- Fix up the CONFIG_PINCTRL_ST Kconfig sort order as noted during the
merge window
- Fix an unexpected interrupt problem on the Intel Sunrisepoint
- Fix a glitch when updating IRQ flags on all Intel pin controllers
- Revert a Zynqmp patch to unify the pin naming, let's find some
better solution
- Fix some error paths in the Broadcom BCM2835 driver
- Fix a Kconfig problem pertaining to the BCM63XX drivers
- Fix the regmap support in the Microchip SGPIO driver"
* tag 'pinctrl-v5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: microchip-sgpio: Fix support for regmap
pinctrl: bcm63xx: fix unmet dependency on REGMAP for GPIO_REGMAP
pinctrl: bcm2835: Fix a few error paths
pinctrl: zynqmp: Revert "Unify pin naming"
pinctrl: intel: Fix a glitch when updating IRQ flags on a preconfigured line
pinctrl: intel: fix unexpected interrupt
pinctrl: Place correctly CONFIG_PINCTRL_ST in the Makefile
pinctrl: sunxi: Fix H616 I2S3 pin data
pinctrl: cherryview: Trigger hwirq0 for interrupt-lines without a mapping
pinctrl: thunderbay: rework loops looking for groups names
pinctrl: thunderbay: comment process of building functions a bit
Do not try to use any SKB fields after the packet has been passed up in the
receive stack.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20220202083039.3774851-1-steen.hegelund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On error path from cond_read_list() and duplicate_policydb_cond_list()
the cond_list_destroy() gets called a second time in caller functions,
resulting in NULL pointer deref. Fix this by resetting the
cond_list_len to 0 in cond_list_destroy(), making subsequent calls a
noop.
Also consistently reset the cond_list pointer to NULL after freeing.
Cc: stable@vger.kernel.org
Signed-off-by: Vratislav Bendel <vbendel@redhat.com>
[PM: fix line lengths in the description]
Signed-off-by: Paul Moore <paul@paul-moore.com>
The change of sizeof(struct smc_diag_linkinfo) by commit 79d39fc503
("net/smc: Add netlink net namespace support") introduced an ABI
regression: since struct smc_diag_lgrinfo contains an object of
type "struct smc_diag_linkinfo", offset of all subsequent members
of struct smc_diag_lgrinfo was changed by that change.
As result, applications compiled with the old version
of struct smc_diag_linkinfo will receive garbage in
struct smc_diag_lgrinfo.role if the kernel implements
this new version of struct smc_diag_linkinfo.
Fix this regression by reverting the part of commit 79d39fc503 that
changes struct smc_diag_linkinfo. After all, there is SMC_GEN_NETLINK
interface which is good enough, so there is probably no need to touch
the smc_diag ABI in the first place.
Fixes: 79d39fc503 ("net/smc: Add netlink net namespace support")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220202030904.GA9742@altlinux.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4:
- Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith says:
====================
Add support for qca8k mdio rw in Ethernet packet
The main reason for this is that we notice some routing problem in the
switch and it seems assisted learning is needed. Considering mdio is
quite slow due to the indirect write using this Ethernet alternative way
seems to be quicker.
The qca8k switch supports a special way to pass mdio read/write request
using specially crafted Ethernet packet.
This works by putting some defined data in the Ethernet header where the
mac source and dst should be placed. The Ethernet type header is set to qca
header and is set to a mdio read/write type.
This is used to communicate to the switch that this is a special packet
and should be parsed differently.
Currently we use Ethernet packet for
- MIB counter
- mdio read/write configuration
- phy read/write for each port
Current implementation of this use completion API to wait for the packet
to be processed by the tagger and has a timeout that fallback to the
legacy mdio way and mutex to enforce one transaction at time.
We now have connect()/disconnect() ops for the tagger. They are used to
allocate priv data in the dsa priv. The header still has to be put in
global include to make it usable by a dsa driver.
They are called when the tag is connect to the dst and the data is freed
using discconect on tagger change.
(if someone wonder why the bind function is put at in the general setup
function it's because tag is set in the cpu port where the notifier is
still not available and we require the notifier to sen the
tag_proto_connect() event.
We now have a tag_proto_connect() for the dsa driver used to put
additional data in the tagger priv (that is actually the dsa priv).
This is called using a switch event DSA_NOTIFIER_TAG_PROTO_CONNECT.
Current use for this is adding handler for the Ethernet packet to keep
the tagger code as dumb as possible.
The tagger priv implement only the handler for the special packet. All the
other stuff is placed in the qca8k_priv and the tagger has to access
it under lock.
We use the new API from Vladimir to track if the master port is
operational or not. We had to track many thing to reach a usable state.
Checking if the port is UP is not enough and tracking a NETDEV_CHANGE is
also not enough since it use also for other task. The correct way was
both track for interface UP and if a qdisc was assigned to the
interface. That tells us the port (and the tagger indirectly) is ready
to accept and process packet.
I tested this with multicpu port and with port6 set as the unique port and
it's sad.
It seems they implemented this feature in a bad way and this is only
supported with cpu port0. When cpu port6 is the unique port, the switch
doesn't send ack packet. With multicpu port, packet ack are not duplicated
and only cpu port0 sends them. This is the same for the MIB counter.
For this reason this feature is enabled only when cpu port0 is enabled and
operational.
v8:
- Reworked to rolling counter for the seq_num
- Reworked the hi/lo cache patch
- Fix multiple missing skb free and mutex lock errors
- Fix some spelling mistake
- Add macro build check for mgmt packet size
- Change some struct naming to make them more descriptive
v7:
- Rebase on net-next changes
- Add bulk patches to speedup this even more
v6:
- Fix some error in ethtool handler caused by rebase/cleanup
v5:
- Adapt to new API fixes
- Fix a wrong logic for noop
- Add additional lock for master_state change
- Limit mdio Ethernet to cpu port0 (switch limitation)
- Add priority to these special packet
- Move mdio cache to qca8k_priv
v4:
- Remove duplicate patch sent by mistake.
v3:
- Include MIB with Ethernet packet.
- Include phy read/write with Ethernet packet.
- Reorganize code with new API.
- Introuce master tracking by Vladimir
v2:
- Address all suggestion from Vladimir.
Try to generilize this with connect/disconnect function from the
tagger and tag_proto_connect for the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce qca8k_bulk_read/write() function to use mgmt Ethernet way to
read/write packet in bulk. Make use of this new function in the fdb
function and while at it reduce the reg for fdb_read from 4 to 3 as the
max bit for the ARL(fdb) table is 83 bits.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mgmt Ethernet packet can read/write up to 16byte at times. The len reg
is limited to 15 (0xf). The switch actually sends and accepts data in 4
different steps of len values.
Len steps:
- 0: nothing
- 1-4: first 4 byte
- 5-6: first 12 byte
- 7-15: all 16 byte
In the alloc skb function we check if the len is 16 and we fix it to a
len of 15. It the read/write function interest to extract the real asked
data. The tagger handler will always copy the fully 16byte with a READ
command. This is useful for some big regs like the fdb reg that are
more than 4byte of data. This permits to introduce a bulk function that
will send and request the entire entry in one go.
Write function is changed and it does now require to pass the pointer to
val to also handle array val.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Documentation, we can cache lo and hi the same way we do with the
page. This massively reduce the mdio write as 3/4 of the time as we only
require to write the lo or hi part for a mdio write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There can be multiple qca8k switch on the same system. Move the static
qca8k_current_page to qca8k_priv and make it specific for each switch.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
