Add a generic driver for GNSS receivers with a USB interface with two
bulk endpoints.
The driver currently assumes that the device protocol is NMEA (only) but
this can be generalised later as needed.
Link: https://lore.kernel.org/r/20211220111901.23206-2-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Marc Ferland <ferlandm@amotus.ca>
Signed-off-by: Johan Hovold <johan@kernel.org>
Rename the VSC capability: TB_VSE_CAP_IECS to TB_VSE_CAP_CP_LP to follow
the Intel devices namings as appear in the datasheet. This capability
is used for controlling CLx (Low Power states of the link).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Titan Ridge based routers have slightly different flow for time
disruption than USB4 compliant routers. This makes it work on Titan
Ridge too. Needed to enable link low power states on Titan Ridge.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently usb4_switch_wait_for_bit() used only in usb4.c Moving to
switch.c to call it from other files. Also change the prefix to "tb_"
to follow to the naming convention.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In this patch we add enabling of CL0s - a low power state of the link.
Low power states (called collectively CLx) are used to reduce
transmitter and receiver power when a high-speed lane is idle. For now,
we add support only for first low power state: CL0s. We enable it, if
both sides of the link support it, and only for the first hop router.
(i.e. the first device that connected to the host router). This is
needed for better thermal management.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Up until Titan Ridge (Thunderbolt 3) device routers only supported
bi-directional mode. In this patch we add to TMU a uni-directional mode.
The uni-directional mode is needed for enabling of low power state of
the link (CLx).
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently, we parse the "linux,usable-memory-range" property in
early_init_dt_scan_chosen(), to obtain the specified memory range of the
crash kernel. We then reserve the required memory after
early_init_dt_scan_memory() has identified all available physical memory.
Because the two pieces of code are separated far, the readability and
maintainability are reduced. So bring them together.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
(change the prototype of early_init_dt_check_for_usable_mem_range(), in
order to use it outside)
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Tested-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
To: devicetree@vger.kernel.org
To: linux-efi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add an explicit comment to document that the reference initialised by
platform_device_register() needs to be released by a call to
platform_device_put() also when registration fails (cf.
device_register()).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211222104213.5673-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-5-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-4-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-3-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use auxiliary_get_drvdata and auxiliary_set_drvdata helpers.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211221235852.323752-2-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Platform Monitoring Technology (PMT) support is indicated by presence
of an Intel defined PCIe Designated Vendor Specific Extended Capabilities
(DVSEC) structure with a PMT specific ID. The current MFD implementation
creates child devices for each PMT feature, currently telemetry, watcher,
and crashlog. However DVSEC structures may also be used by Intel to
indicate support for other features. The Out Of Band Management Services
Module (OOBMSM) uses DVSEC to enumerate several features, including PMT.
In order to support them it is necessary to modify the intel_pmt driver to
handle the creation of the child devices more generically. To that end,
modify the driver to create child devices for any VSEC/DVSEC features on
supported devices (indicated by PCI ID). Additionally, move the
implementation from MFD to the Auxiliary bus. VSEC/DVSEC features are
really multifunctional PCI devices, not platform devices as MFD was
designed for. Auxiliary bus gives more flexibility by allowing the
definition of custom structures that can be shared between associated
auxiliary devices and the parent device. Also, rename the driver from
intel_pmt to intel_vsec to better reflect the purpose.
This series also removes the current runtime pm support which was not
complete to begin with. None of the current devices require runtime pm.
However the support will be replaced when a device is added that requires
it.
Reviewed-by: Mark Gross <markgross@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211208015015.891275-4-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds get/set driver data helpers for auxiliary devices.
Reviewed-by: Mark Gross <markgross@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211208015015.891275-3-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add #defines for accessing Vendor ID, Revision, Length, and ID offsets
in the Designated Vendor Specific Extended Capability (DVSEC). Defined
in PCIe r5.0, sec 7.9.6.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20211208015015.891275-2-david.e.box@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used in meson-sm1 and meson-g12 .dtsi. Add the property to
the binding.
This fixes the dtschema warning:
audio-controller@740: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-3-alexander.stein@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This is used in meson-gxl and meson-g12-common .dtsi. Add the property to
the binding.
This fixes the dtschema warning:
audio-controller@32000: 'sound-name-prefix' does not match any of the
regexes: 'pinctrl-[0-9]+'
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-2-alexander.stein@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
name-prefix.txt does not exist anymore, just reference the schema instead.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211218143423.18768-1-alexander.stein@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In uniphier_spi_remove(), there is a wrong code to get private data from
the platform device, so the driver can't be removed properly.
The driver should get spi_master from the platform device and retrieve
the private data from it.
Cc: <stable@vger.kernel.org>
Fixes: 5ba155a4d4 ("spi: add SPI controller driver for UniPhier SoC")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1640148492-32178-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code represent memory/cache level data based on PERF_MEM_LVL_*
namespace, which is in the process of deprication in the favour of newer
composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields. Add data
source encodings to represent cache/memory data based on newer composite
PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields.
Add data source encodings to represent data coming from local
memory/Remote memory/distant memory and remote/distant cache hits.
Inorder to represent data coming from OpenCAPI cache/memory, we use
LVLNUM "PMEM" field which is used to present persistent memory accesses.
Result in power10 system with patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ....... ...................................... ........................... .................
#
29.46% 2331 L1 or L1 hit [.] __random libc-2.28.so
23.11% 2121 L1 or L1 hit [.] producer_populate_cache producer_consumer
18.56% 1758 L1 or L1 hit [.] __random_r libc-2.28.so
15.64% 1559 L2 or L2 hit [.] __random libc-2.28.so
.....
0.09% 5 Remote socket, same board Any cache hit [.] __random libc-2.28.so
0.07% 4 Remote socket, same board Any cache hit [.] __random libc-2.28.so
.....
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lore.kernel.org/lkml/20211206091749.87585-5-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The code represent data coming from L1/L2/L3 cache hits based on
PERF_MEM_LVL_* namespace, which is in the process of deprecation in the
favour of newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_}
fields.
Add data source encodings to represent L1/L2/L3 cache hits based on
newer composite PERF_MEM_{LVLNUM_,REMOTE_,SNOOPX_,HOPS_} fields for
power10 and older platforms
Result in power9 system without patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ....... ............. ................................. ................
#
29.51% 1 L2 hit [k] perf_event_exec [kernel.vmlinux]
27.05% 1 L1 hit [k] perf_ctx_unlock [kernel.vmlinux]
13.93% 1 L1 hit [k] vtime_delta [kernel.vmlinux]
13.11% 1 L1 hit [k] prepend_path.isra.11 [kernel.vmlinux]
8.20% 1 L1 hit [.] 00000038.plt_call.__GI_strlen libc-2.28.so
8.20% 1 L1 hit [k] perf_event_interrupt [kernel.vmlinux]
Result in power9 system with patch changes:
localhost:# ./perf mem report --sort="mem,sym,dso" --stdio
# Overhead Samples Memory access Symbol Shared Object
# ........ ....... ............. .......................... ................
#
36.63% 1 L2 or L2 hit [k] perf_event_exec [kernel.vmlinux]
25.50% 1 L1 or L1 hit [k] vtime_delta [kernel.vmlinux]
13.12% 1 L1 or L1 hit [k] unmap_region [kernel.vmlinux]
12.62% 1 L1 or L1 hit [k] perf_sample_event_took [kernel.vmlinux]
6.93% 1 L1 or L1 hit [k] perf_ctx_unlock [kernel.vmlinux]
5.20% 1 L1 or L1 hit [.] __memcpy_power7 libc-2.28.so
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lore.kernel.org/lkml/20211206091749.87585-4-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add new macros for mem_hops field which can be used to represent
remote-node, socket and board level details.
Currently the code had macro for HOPS_0 which, corresponds to data
coming from another core but same node. Add new macros for HOPS_1 to
HOPS_3 to represent remote-node, socket and board level data.
Also add corresponding strings in the mem_hops array to represent
mem_hop field data in perf_mem__lvl_scnprintf function
Incase mem_hops field is used, PERF_MEM_LVLNUM field also need to be set
inorder to represent the data source. Hence printing data source via
PERF_MEM_LVL field can be skip in that scenario.
For ex: Encodings for mem_hops fields with L2 cache:
L2 - local L2
L2 | REMOTE | HOPS_0 - remote core, same node L2
L2 | REMOTE | HOPS_1 - remote node, same socket L2
L2 | REMOTE | HOPS_2 - remote socket, same board L2
L2 | REMOTE | HOPS_3 - remote board L2
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lore.kernel.org/lkml/20211206091749.87585-3-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The TI's AM64 SoC has the GPMC module. Add compatible for it.
Traditionally GPMC external addresses have always been mapped to first
1GB physical address. However newer platforms, can have it mapped
at different locations. Support this address provision via device tree.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20211221131757.2030-3-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
AM64 SoC contains the GPMC module. Add compatible for it.
Newer SoCs don't necessarily map GPMC data region at the same place
as legacy SoCs. Add reg-names "data", to provide this information to
the device driver.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211221131757.2030-2-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20211221203916.18588-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
-----BEGIN PGP SIGNATURE-----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=xXvq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
The hardware is capable of controlling any non-contiguous sequence of
LEDs specified in the DT using qcom,enabled-strings as u32
array, and this also follows from the DT-bindings documentation. The
numbers specified in this array represent indices of the LED strings
that are to be enabled and disabled.
Its value is appropriately used to setup and enable string modules, but
completely disregarded in the set_brightness paths which only iterate
over the number of strings linearly.
Take an example where only string 2 is enabled with
qcom,enabled_strings=<2>: this string is appropriately enabled but
subsequent brightness changes would have only touched the zero'th
brightness register because num_strings is 1 here. This is simply
addressed by looking up the string for this index in the enabled_strings
array just like the other codepaths that iterate over num_strings.
Likewise enabled_strings is now also used in the autodetection path for
consistent behaviour: when a list of strings is specified in DT only
those strings will be probed for autodetection, analogous to how the
number of strings that need to be probed is already bound by
qcom,num-strings. After all autodetection uses the set_brightness
helpers to set an initial value, which could otherwise end up changing
brightness on a different set of strings.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Fixes: 03b2b5e869 ("backlight: qcom-wled: Add support for WLED4 peripheral")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-10-marijn.suijten@somainline.org
Remove redundant spaces inside for loop conditions. No other double
spaces were found that are not part of indentation with `[^\s] `.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-9-marijn.suijten@somainline.org
Only WLED 3 sets a sensible default that allows operating this driver
with just qcom,num-strings in the DT; WLED 4 and 5 require
qcom,enabled-strings to be provided otherwise enabled_strings remains
zero-initialized, resulting in every string-specific register write
(currently only the setup and config functions, brightness follows in a
future patch) to only configure the zero'th string multiple times.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-8-marijn.suijten@somainline.org
The previous commit improves num_strings parsing to not go over the
maximum of 3 strings for WLED3 anymore. Likewise this default index for
a hypothetical 4th string is invalid and could access registers that are
not mapped to the desired purpose.
Removing this value gets rid of undesired confusion and avoids the
possibility of accessing registers at this offset even if the 4th array
element is used by accident.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-7-marijn.suijten@somainline.org
The length of qcom,enabled-strings as property array is enough to
determine the number of strings to be enabled, without needing to set
qcom,num-strings to override the default number of strings when less
than the default (which is also the maximum) is provided in DT.
This also introduces an extra warning when qcom,num-strings is set,
denoting that it is not necessary to set both anymore. It is usually
more concise to set just qcom,num-length when a zero-based, contiguous
range of strings is needed (the majority of the cases), or to only set
qcom,enabled-strings when a specific set of indices is desired.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-6-marijn.suijten@somainline.org
When not specifying num-strings in the DT the default is used, but +1 is
added to it which turns WLED3 into 4 and WLED4/5 into 5 strings instead
of 3 and 4 respectively, causing out-of-bounds reads and register
read/writes. This +1 exists for a deficiency in the DT parsing code,
and is simply omitted entirely - solving this oob issue - by parsing the
property separately much like qcom,enabled-strings.
This also enables more stringent checks on the maximum value when
qcom,enabled-strings is provided in the DT, by parsing num-strings after
enabled-strings to allow it to check against (and in a subsequent patch
override) the length of enabled-strings: it is invalid to set
num-strings higher than that.
The DT currently utilizes it to get around an incorrect fixed read of
four elements from that array (has been addressed in a prior patch) by
setting a lower num-strings where desired.
Fixes: 93c64f1ea1 ("leds: add Qualcomm PM8941 WLED driver")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-By: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-5-marijn.suijten@somainline.org
The kernel already provides appropriate primitives to perform endianness
conversion which should be used in favour of manual bit-wrangling.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-4-marijn.suijten@somainline.org
of_property_read_u32_array takes the number of elements to read as last
argument. This does not always need to be 4 (sizeof(u32)) but should
instead be the size of the array in DT as read just above with
of_property_count_elems_of_size.
To not make such an error go unnoticed again the driver now bails
accordingly when of_property_read_u32_array returns an error.
Surprisingly the indentation of newlined arguments is lining up again
after prepending `rc = `.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-3-marijn.suijten@somainline.org
The strings passed in DT may possibly cause out-of-bounds register
accesses and should be validated before use.
Fixes: 775d2ffb4a ("backlight: qcom-wled: Restructure the driver for WLED3")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211115203459.1634079-2-marijn.suijten@somainline.org
The Xiaomi Mi Pad 2 tablet uses an ACPI enumerated LP8556 backlight
controller for its LCD-panel, with a Xiaomi specific ACPI HID of
"XMCC0001", add support for this.
Note the new "if (id)" check also fixes a NULL pointer deref when a user
tries to manually bind the driver from sysfs.
When CONFIG_ACPI is disabled acpi_match_device() will always return NULL,
so the lp855x_parse_acpi() call will get optimized away.
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211102225504.18920-3-hdegoede@redhat.com
Add a dev local variable to the lp855x_probe(), to replace "&cl->dev"
and "lp->dev" in various places.
Also switch to dev_err_probe() in one case which takes care of not
printing -EPROBE_DEFER errors for us.
This is mostly a preparation for adding ACPI enumeration support which
will use the new "dev" variable more.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211102225504.18920-2-hdegoede@redhat.com
Move the setting of the lp->cfg pointer to the chip specific
lp855x_device_config struct from lp855x_configure() to
lp855x_probe(), before calling lp855x_parse_dt().
This is a preperation patch for adding ACPI enumeration support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211102225504.18920-1-hdegoede@redhat.com
When facing a really early issue on DT parsing we have currently
a message that shows both the physical and virtual address of the FDT.
The printk pointer modifier for the virtual address shows a hashed
address there unless the user provides "no_hash_pointers" parameter in
the command-line. The situation in which this message shows-up is a bit
more serious though: the boot process is broken, nothing can be done
(even an oops is too much for this early stage) so we have this message
as a last resort in order to help debug bootloader issues, for example.
Hence, we hereby change that to "%px" in order to make debugging easy,
there's not much information leak risk in such early boot failure.
Also, we tried to improve a bit the commenting on that function, given
that if kernel fails there, it just hangs forever in a cpu_relax() loop.
The reason we cannot BUG/panic is that is too early to do so; thanks to
Mark Brown for pointing that on IRC and thanks Robin Murphy for the good
pointer hash discussion in the mailing-list.
Cc: Mark Brown <broonie@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211221155230.1532850-1-gpiccoli@igalia.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit in Fixes added a global TLB flush on the early boot path, after
the kernel switches off of the trampoline page table.
Compiler profiling options enabled with GCOV_PROFILE add additional
measurement code on clang which needs to be initialized prior to
use. The global flush in x86_64_start_kernel() happens before those
initializations can happen, leading to accessing invalid memory.
GCOV_PROFILE builds with gcc are still ok so this is clang-specific.
The second issue this fixes is with KASAN: for a similar reason,
kasan_early_init() needs to have happened before KASAN-instrumented
functions are called.
Therefore, reorder the flush to happen after the KASAN early init
and prevent the compilers from adding profiling instrumentation to
native_write_cr4().
Fixes: f154f29085 ("x86/mm/64: Flush global TLB on boot and AP bringup")
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Carel Si <beibei.si@intel.com>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Link: https://lore.kernel.org/r/20211209144141.GC25654@xsang-OptiPlex-9020
For memory accesses with write-combining attributes (e.g. those returned
by ioremap_wc()), the CPU may wait for prior accesses to be merged with
subsequent ones. But in some situation, such wait is bad for the
performance.
We introduce io_stop_wc() to prevent the merging of write-combining
memory accesses before this macro with those after it.
We add implementation for ARM64 using DGH instruction and provide NOP
implementation for other architectures.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Suggested-by: Will Deacon <will@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211221035556.60346-1-wangxiongfeng2@huawei.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because platform_get_irq() could fail and return error irq.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: ae150435b5 ("smsc: Move the SMC (SMSC) drivers")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b22 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the commit 448cf90513 ("gpio: Get rid of duplicate of_node
assignment in the drivers") the OF node local pointers become unused.
Remove them for good and make compiler happy about.
Fixes: 448cf90513 ("gpio: Get rid of duplicate of_node assignment in the drivers")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Bart: removed unrelated change in gpio-brcmstb]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Convert the sg_is_chain(), sg_is_last() and sg_chain_ptr() macros
into static inline functions. There's no reason for these to be macros
and static inline are generally preferred these days.
Also introduce the SG_PAGE_LINK_MASK define so the P2PDMA work, which is
adding another bit to this mask, can do so more easily.
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 2a86f66121 ("kbuild: use KBUILD_DEFCONFIG as the fallback for
DEFCONFIG_LIST") removed ARCH_DEFCONFIG because it does not make much
sense.
In the same development cycle, Commit ededa081ed ("parisc: Fix
defconfig selection") added ARCH_DEFCONFIG for parisc.
Please use KBUILD_DEFCONFIG in arch/*/Makefile for defconfig selection.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
