Current driver create DMIC dai based on quirk for each platforms,
so we need to add quirk for new platforms. Now driver reports DMIC
number to machine driver and machine driver can create DMIC dai based
on this information. The old check is reserved for some platforms
may be failed to set the DMIC number in BIOS.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
UCM needs to know which microphone is used (dmic or RT715-based),
let's add the information in the component string.
Note the slight change from HDAudio platforms where 'cfg-dmics' was
used. 'cfg-mics' is used here with the intent that this component
string describes either the number of PCH-attached microphones or the
number of RT715-attached ones (the assumption is that the two
configurations are mutually exclusive).
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the same style for all quirks to avoid misses and errors
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk table is a mess, let's reorganize it by generation before
making sure that the quirks are consistent for each generation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a prefix on max98373 codec, and the prefix will be added to
the pin name However, there is no prefix on the "Right Spk" and "Left
Spk" widgets.
To avoid getting a redundant prefix, we should get dapm from cpu_dai
component.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210208234043.59750-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new ASoc Machine driver for Intel Baytrail platforms with a
Wolfson Microelectronics WM5102 codec.
This is based on a past contributions [1] from Paulo Sergio Travaglia
<pstglia@gmail.com> based on the Levono kernel [2] combined with
insights in things like the speaker GPIO from the android-x86 android
port for the Lenovo Yoga Tablet 2 1051F/L [3].
[1] https://patchwork.kernel.org/project/alsa-devel/patch/593313f5.3636c80a.50e05.47e9@mx.google.com/
[2] https://github.com/lenovo-yt2-dev/android_kernel_lenovo_baytrail/blob/cm-12.1/sound/soc/intel/board/byt_bl_wm5102.c
[3] https://github.com/Kitsune2222/Android_Yoga_Tablet_2-1051F_Kernel
The original machine driver from the Android ports was a crude modified
copy of bytcr_rt5640.c adjusted to work with the WM5102 codec.
This version has been extensively reworked to:
1. Remove all rt5640 related quirk handling. to the best of my knowledge
this setup is only used on the Lenovo Yoga Tablet 2 series (8, 10 and 13
inch models) which all use the same setup. So there is no need to deal
with all the variations with which we need to deal on rt5640 boards.
2. Rework clock handling, properly turn off the FLL and the platform-clock
when they are no longer necessary and don't reconfigure the FLL
unnecessarily when it is already running. This fixes a number of:
"Timed out waiting for lock" warnings being logged.
3. Add the GPIO controlled Speaker-VDD regulator as a DAPM_SUPPLY
This only adds the machine driver and ACPI hooks, the BYT-CR detection
quirk which these devices need will be added in a separate patch.
BugLink: https://github.com/thesofproject/linux/issues/2485
Co-authored-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210120214957.140232-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: e787f5b5b1 ('ASoC: Intel: add support for new SoundWire hardware layout on TGL')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: 488cdbd893 ('ASoC: Intel: sof_sdw: add quirk for new TigerLake-SDCA device')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: 9ad9bc59dd ('ASoC: Intel: sof_sdw: set proper flags for Dell TGL-H SKU 0A5E')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add flag "SOF_RT711_JD_SRC_JD2", flag "SOF_RT715_DAI_ID_FIX"
and "SOF_SDW_FOUR_SPK" to the Dell TGL-H based SKU "0A5E".
Signed-off-by: Libin Yang <libin.yang@intel.com>
Co-developed-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210125081117.814488-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi All,
This series adds support for devices with only a headphone jack
(no speakers/internal mic). Specifically this adds support for the
Mele PCG03 Mini PC. But the new no-speakers and no-internal-mic quirks
will likely be useful on other devices too.
Regards,
Hans
Move the snd_soc_dai_set_tdm_slot() call from cht_codec_init() to
cht_codec_fixup(). There are 2 reasons for doing this:
1. This aligns the cht_bsw_nau8824 with all the other BYT/CHT machine
drivers which also do this from their codec_fixup function.
2. When using the SOF driver, things like the TDM info is set from the
topology file. Moving the call to the codec_fixup function, which gets
skipped when using the SOF driver avoids the call interfering with the
settings when using the SOF driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210107115324.11602-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Mele PCG03 Mini PC, being a Mini PC this device
has no speakers and no internal microphone.
To make matters worse the speaker output pins are shorted (to gnd or
to each other?) and SPKVDD is provided. So trying to output sound on the
speakers leads to shorting SPKVDD, this leads to a power dip after
which the codec is an unknown state. Sometimes it drops of the i2c
bus, sometimes it does still respond to i2c transfers, but is otherwise
not functional. TL;DR: trying to use the speaker outputs on this model
is BAD.
Besides not having speakers / an internal mic, this is a Bay Trail CR
device without a CHAN package in ACPI, so we default to SSP0-AIF2 as
codec connection. But the device is actually using SSP0-AIF1, so we
need to quirk that too.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices, like mini PCs/media/top-set boxes do not have an internal
microphone at all, an example of the is the Mele PCG03 Mini PC.
Add a new BYT_RT5640_NO_INTERNAL_MIC_MAP input-mapping for this,
which does not add any internal-mic routes and modifies the components
and the (optional) long_name strings to reflect this.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices, like mini PCs/media/top-set boxes do not have any speakers
at all, an example of the is the Mele PCG03 Mini PC.
Add a new BYT_RT5640_NO_SPEAKERS quirk-flag which when sets does not add
speaker routes and modifies the components and the (optional) long_name
strings to reflect that there are no speakers.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove a stale comment about SSP0 being untested, the
bytcht_es8316 has supported SSP0 for a while now and this has
been successfully tested on a GP electrinic T701 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210107120757.12051-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bclk_ratio is unused. Removes bclk_ratio and .set_bclk_ratio callback.
Removes snd_soc_dai_set_bclk_ratio() in a few machine drivers which are
obviously using rt1015.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224101854.3024823-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
haswell machine board is missing pm_ops what prevents it from undergoing
suspend-resume procedure successfully. Assign default snd_soc_pm_ops so
this is no longer the case.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201217105401.27865-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tha ARCHOS Cesium 140 tablet has problem with the jack-sensing,
thus the heaset functions are not working.
Add quirk for this model to select the correct input map, jack-detect
options and channel map to enable jack sensing and headset microphone.
This device uses IN1 for its internal MIC and JD2 for jack-detect.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201208060414.27646-1-chiu@endlessos.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd-soc-sst-acpi driver does not care about the id specified for
the SSP2-Codec DAI, but it does matter for the snd-sof-acpi driver;
and when it is not 0 then the snd-sof-acpi driver does not work.
Set the SSP2-Codec DAI id to 0, fixing the snd-sof-acpi driver not
working on devices using the cht_bsw_nau8824 machine-driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201206122436.13553-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the snd-soc-sst-acpi driver then the compress-cpu-dai bits are
not used, the cht_bsw_nau8824 machine-driver is the only BYT/CHT driver
defining them.
When using the snd-sof-acpi driver then the presence of the
compress-cpu-dai bits breaks things because the sof topology file for
by/cht devices does not contain routing info for them.
Drop the compress-cpu-dai bits, fixing the snd-sof-acpi driver not
working on devices using the cht_bsw_nau8824 machine-driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201206122436.13553-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the driver data for two rt1011 speaker amplifiers on
SSP1 and rt5682 on SSP0 for TGL platform. DAI format for rt1011 is
leveraged from cml_rt1011_rt5682 which is 4-slot tdm with 100fs bclk.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201203154010.29464-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Speaker amp's SSP bclk configuration was changed in the topology file to be
based on 12.288MHz and dai_ops->hw_params is based on s32le format.
But, the TDM slot size remained set to 24 bits.
This inconsistency created audible noises and needs to be corrected.
This patch updates TDM slot width to 32.
Fixes: bc7477fc2a ("ASoC: Intel: Boards: tgl_max98373: Update TDM configuration in hw_params")
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201201211150.433472-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Atom/SST driver does not rely on ASoC power management, but the
SOF driver does. Rather than using a hard-coded build-time assignment,
we can set this pm_ops dynamically depending on what the parent
is. That will remove the last build-time dependency and allow for
coexistence of both SST and SOF drivers for Baytrail/Cherrytrail.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid hard-coded variations between SOF and SST drivers, set the
card name and driver dynamically depending on the parent type. This is
the first pass required to let distributions select which drivers to
use with kernel parameters instead of build-time selection.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason this ops is missing in 2 out of the 3 broadwell
drivers. Add to make sure ASoC takes care of power management.
Tested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason this ops is missing in 2 out of the 3 broadwell
drivers. Add to make sure ASoC takes care of power management.
Tested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Pavilion x2 Detachable line comes in many variants:
1. Bay Trail SoC + AXP288 PMIC, Micro-USB charging (10-k010nz, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable PC 10"
DMI_BOARD_NAME: "8021"
2. Bay Trail SoC + AXP288 PMIC, Type-C charging (10-n000nd, 10-n010nl, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "815D"
3. Cherry Trail SoC + AXP288 PMIC, Type-C charging (10-n101ng, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "813E"
4. Cherry Trail SoC + TI PMIC, Type-C charging (10-p002nd, 10-p018wm, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 Detachable 10-p0XX"
DMI_BOARD_NAME: "827C"
5. Cherry Trail SoC + TI PMIC, Type-C charging (x2-210-g2, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 210 G2"
DMI_BOARD_NAME: "82F4"
Variant 1 needs the exact same quirk as variant 2, so relax the DMI check
for the existing quirk a bit so that it matches both variant 1 and 2
(note the other variants will still not match).
Variant 2 already has an existing quirk (which now also matches variant 1)
Variant 3 uses a cx2072x codec, so is not applicable here.
Variant 4 almost works with the defaults, but it also needs a quirk to
fix jack-detection, add a new quirk for this.
Variant 5 does use a RT5640 codec (based on old dmesg output), but was
otherwise not tested, keep using the defaults for this variant.
Fixes: ec8e8418ff ("ASoC: Intel: bytcr_rt5640: Add quirks for various devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201118121515.11441-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In kabylake_set_bias_level(), enabling mclk may fail if the clock has
already been enabled by the firmware. Attempts to disable that clock
later will fail with a warning backtrace.
mclk already disabled
WARNING: CPU: 2 PID: 108 at drivers/clk/clk.c:952 clk_core_disable+0x1b6/0x1cf
...
Call Trace:
clk_disable+0x2d/0x3a
kabylake_set_bias_level+0x72/0xfd [snd_soc_kbl_rt5663_rt5514_max98927]
snd_soc_card_set_bias_level+0x2b/0x6f
snd_soc_dapm_set_bias_level+0xe1/0x209
dapm_pre_sequence_async+0x63/0x96
async_run_entry_fn+0x3d/0xd1
process_one_work+0x2a9/0x526
...
Only disable the clock if it has been enabled.
Fixes: 15747a8020 ("ASoC: eve: implement set_bias_level function for rt5514")
Cc: Brent Lu <brent.lu@intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111205434.207610-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Smart_amp_speaker device has the playback stream and capture stream
associated to it. Hence add the dpcm_capture = 1 flag while dailink
creation.
This patches fixes:
ERR kernel [timestamp] SSP1-Codec: ASoC: no backend capture stream
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201109210958.84198-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This DMI product family string of this board is "Google_Hatch" so the
DMI quirk will take place. However, this board is using rt1015 speaker
amp instead of max98357a specified in the quirk. Therefore, we need an
new DMI quirk for this board.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201030170559.20370-3-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the driver data and updates quirk info for cml with
rt1015 speaker amp and rt5682 headset codec. Due to different mclk
frequency on JSL and CML, we need to use 4 slot TDM 100fs to avoid
the SSP m/n counter.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201030170559.20370-2-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/1602407979-29038-4-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
With sound/soc/intel/haswell and /baytrail gone, registers left within
sst-dsp header are atom-specific. Relocate these to atom internal header
to make atom truely independent of sound/soc/common processing code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
byt-rt5640 is deprecated in favor of bytcr_rt5640 used by
sound/soc/intel/atom and SOF solutions both. Remove redundant machine
board and all related code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
byt-max98090 is deprecated in favor of cht-bsw-max98090 used by
sound/soc/intel/atom and SOF solutions both. Remove redundant machine
board and all related code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RT715 and RT714 are essentially the same chip. In addition, there are
two versions, one supporting SoundWire 1.1 and one supporting
SoundWire 1.2 (SDCA).
The previous configurations assumed that RT714 was SDCA-only, which
isn't correct. Add support for the 4 possible combinations to avoid
confusions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201002211902.287692-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply same test as for other amplifiers - in case we enable feedback
one day.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201002211902.287692-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevent sound/soc/intel/haswell code compile and select catpt instead as
a recommended solution. Userspace-exposed members are compatible with
what is exposed by deprecated solution thus no harm is done. The only
visible difference is the newly added 'Loopback Mute' kcontrol.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-15-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove code specific to sound/soc/intel/haswell. Update BE dai_link
definition to provide seamless transition to catpt solution.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-14-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove code specific to sound/soc/intel/haswell. Update BE dai_link
definition to provide seamless transition to catpt solution.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-13-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove code specific to sound/soc/intel/haswell. Update BE dai_link
definition to provide seamless transition to catpt solution.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove code specific to sound/soc/intel/haswell. Update BE dai_link
definition to provide seamless transition to catpt solution.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-11-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck reports the following warning:
sound/soc/intel/boards/hda_dsp_common.c:17:0: style: The function
'hda_dsp_hdmi_pcm_handle' is never used. [unusedFunction]
Fix by moving to static inside compilation block.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923072939.3100468-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Max98373 amplifier provides I/V feedback information, which keeps
a DAPM path active even when there is no playback happening. This
prevents entry in low-power mode. Rather than adding new controls and
require UCM/user interaction, the method previously applied is to
enable/disable the Speaker pin during the dailink trigger operations.
Recent changes in the SoundWire stream management moved the stream
trigger to the dailink trigger. This change removed the Maxim-specific
pin handling and resulted in a regression. This patch restores
functionality by combining the SoundWire stream trigger with the pin
enable/disable.
Fixes: ae3a3918ed ('ASoC: Intel: sof_sdw: add dailink .trigger callback')
Fixes: 06998d49bc ('ASoC: Intel: sof_sdw: add dailink .prepare and .hw_free callback')
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923080514.3242858-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The creativity of hardware folks is endless, with a complete
permutation of rt711 (was link0 now link1), rt1308 (was link1 now
link2) and rt715 (was link3 now link0).
Someday we will get all this information from platform firmware, for
now let's add the mapping table.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923080514.3242858-7-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Somehow for this codec we never used any prefix for the controls,
likely because the test platform has a single SoundWire device.
Follow the convention and use the codec prefix across the board to
avoid possible conflicts.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923080514.3242858-6-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the ACPI machine params provide all the information needed,
allocate the card codec_conf dynamically and set .dlc and
.prefix_name.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923080514.3242858-5-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck reports the following warning:
sound/soc/intel/boards/sof_sdw.c:866:46: style: Clarify calculation
precedence for '&' and '?'. [clarifyCalculation]
hdmi_num = sof_sdw_quirk & SOF_SDW_TGL_HDMI ?
^
There's no reason to use the ternary operator here, we might as well
use a regular if-else construct.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200923080514.3242858-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DMI product name is used to support system variants based out of
tgl_max98373_rt5682 in current implementation. Replace this DMI search with
DMI_OEM_STRING. Coreboot(BIOS used in these systems) is
setting the needed DMI_OEM_STRING field to uniquely identify these
systems.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200910162705.2026036-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add .prepare and .hw_free callback to dailink.
The companion patch for this patch is the removal of stream operations
in the .prepare and .hw_free callbacks at the DAI level in
drivers/soundwire/intel.c
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200904182854.3944-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add trigger functionality to dailink, so far only .startup() and
.shutdown() were implemented at the machine driver level.
The companion patch for this patch is the removal of the trigger
callback at the DAI level in drivers/soundwire/intel.c
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200904182854.3944-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MPMAN Converter9 2-in-1 almost fully works with out default settings.
The only problem is that it has only 1 speaker so any sounds only playing
on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200901080623.4987-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the playback & capture streams are stopped simultaneously, the
SOF PCI device will remain pm_runtime active. The root-cause is a race
condition with two threads reaching the trigger function at the same
time. They see another stream is active so the dapm pin is not
disabled, so the codec remains active as well as the parent PCI
device.
For max98373, the capture stream provides feedback when playback is
working and it is unused when playback is stopped. So the dapm pin
should be set only when playback is active.
Fixes: 94d2d08974 ('ASoC: Intel: Boards: tgl_max98373: add dai_trigger function')
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"struct snd_soc_dapm_widget" and "struct snd_kcontrol_new" are used in most
of these .c files. Adding the header files to prevent from depending on
<sound/soc.h>
Reported-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A Chrome System based on tgl_max98373_rt5682 has different SSP interface
configurations. Using DMI data of this variant DUT, override quirk
data.
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ripto is another product based on TGL with the same
audio hardware configuration as Volteer.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "id" field in sof_sdw_codec_info struct is actually the "part
id". Rename to prevent confusions.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some codecs with the same part id but different SoundWire versions
have different configurations. So we have to separate them in
codec_info_list[].
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the playback & capture streams are stopped simultaneously, the
SOF PCI device will remain pm_runtime active. The root-cause is a race
condition with two threads reaching the trigger function at the same
time. They see another stream is active so the dapm pin is not
disabled, so the codec remains active as well as the parent PCI
device.
For max98373, the capture stream provides feedback when playback is
working and it is unused when playback is stopped. So the dapm pin
should be set only when playback is active.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The UpExtreme board provides support for SoundWire link2 in 2 of the 3
advanced modes. Let's use it w/ rt5682.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We may allocate some resources in sof_sdw_codec_info .init function.
Adding a corresponding .exit function can help to release these resources.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200820134542.8682-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Different modules for HDMI codec are used depending on the
"hda_codec_use_common_hdmi" option being enabled or not. Driver private
context for both of them is different.
This leads to null-pointer dereference error when driver tries to set
autosuspend delay for HDMI codec while the option is off (hdac_hdmi
module is used for HDMI).
Change the string in conditional statement to "ehdaudio0D0" to ensure
that only the HDAudio codec is handled by this function.
Fixes: 5bf73b1b1d ("ASoC: intel/skl/hda - fix oops on systems without i915 audio codec")
Signed-off-by: Mateusz Gorski <mateusz.gorski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200722173524.30161-1-mateusz.gorski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix cppcheck warnings:
sound/soc/intel/boards/bdw-rt5650.c:91:23: style: Local variable
'channels' shadows outer variable [shadowVariable]
sound/soc/intel/boards/bdw-rt5677.c:144:23: style: Local variable
'channels' shadows outer variable [shadowVariable]
sound/soc/intel/boards/broadwell.c:91:23: style: Local variable
'channels' shadows outer variable [shadowVariable]
This was fixed earlier in other machine drivers but keeps coming back
with copy/paste.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200813175839.59422-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can use asoc_substream_to_rtd() macro,
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/87v9i9yddc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kabylake_ssp_fixup function uses snd_soc_dpcm to identify the
codecs DAIs. The HW parameters are changed based on the codec DAI of the
stream. The earlier approach to get snd_soc_dpcm was using container_of()
macro on snd_pcm_hw_params.
The structures have been modified over time and snd_soc_dpcm does not have
snd_pcm_hw_params as a reference but as a copy. This causes the current
driver to crash when used.
This patch changes the way snd_soc_dpcm is extracted. snd_soc_pcm_runtime
holds 2 dpcm instances (one for playback and one for capture). 2 codecs
on the SSP are dmic (capture) and speakers (playback). Based on the
stream direction, snd_soc_dpcm is extracted from snd_soc_pcm_runtime.
Tested for all use cases of the driver.
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Tested-by: Lukasz Majczak <lma@semihalf.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1595432147-11166-1-git-send-email-harshapriya.n@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting in commit cbc7a6b5a8 ("ASoC: soc-card: add
snd_soc_card_add_dai_link()"), error value from ASoc add_dai_link() is
no longer ignored.
The generic HDA machine driver relied on the old semantics to disable
i915 HDMI/DP audio codec at runtime. If no display codec was present,
add_dai_link() returned an error, but this was ignored and rest of the
card was successfully probed.
Fix the problem by changing the machine driver add_dai_link() to not
return an error in this case.
Fixes: cbc7a6b5a8 ("ASoC: soc-card: add snd_soc_card_add_dai_link()")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
BugLink: https://github.com/thesofproject/linux/issues/2261
Link: https://lore.kernel.org/r/20200714132804.3638221-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit d696a61413 ("ASoC: rt1015: Add condition to prevent SoC
providing bclk in ratio of 50 times of sample rate."), PLL input at 50fs
is no longer supported, the new recommended settings at 48Khz rate are:
PLL input SSP bclk
------------------------
64fs 3.073Mhz
100fs 4.8Mhz
(bclk update is reflected in topoplogy.)
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200717211337.31956-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The mc_private->hdmi_pcm_list is populated by elements loaded during
DSP topology load. Valid topologies for this machine driver will always
have PCM nodes for HDMI, but driver should fail gracefully even in the case
this is not true. Add a sanity check to sof_sdw_hdmi_card_late_probe()
for this case. Without the fix, a null pcm handle gets dereferenced.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Link: https://lore.kernel.org/r/20200717211337.31956-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the generic SOF Soundwire machine driver to support systems where
iDisp HDMI/DP audio codec is disabled for some reason (i915 driver
disabled, HDMI/DP implemented with a discrete GPU, etc). Switch codecs
to SoC dummy in the affected DAI links. This allows to reuse existing
topologies for this case.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Link: https://lore.kernel.org/r/20200717211337.31956-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt711 jack detection properties are set from the machine drivers
during the card probe, as done in other ASoC examples.
KASAN reports a use-after-free error when unbinding drivers due to a
confusing sequence between the ACPI core, the device core and the
SoundWire device cleanups.
Rather than fixing this sequence, follow the recommendation to have
the same caller add and remove properties, add an explicit
device_remove_properties() in the card .remove() callback.
In future patches the use of device_add/remove_properties will be
replaced by a direct handling of a swnode, but the sequence will
remain the same.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200717211337.31956-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We can get codec name from dai link.
Suggested-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200717211337.31956-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_byt_cht_es8316_mc_probe() misses to call put_device() in an error
path. Add the missed function call to fix it.
Fixes: ba49cf6f8e ("ASoC: Intel: bytcht_es8316: Add quirk for inverted jack detect")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200714080918.148196-1-jingxiangfeng@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As Pierre-Louis Bossart pointed out, saying that the default mode for the
SSP is TDM 4 slot is not entirely accurate.
There really are 2 default modes:
The default mode for the SSP configuration is TDM 4 slot for the
cpu-dai (hard-coded in DSP firmware),
The default mode for the SSP configuration is I2S for the codec-dai
(hard-coded in the 'SSP2-Codec" .dai_fmt masks, so far unused).
This commit updates the comment in cht_codec_fixup() to properly reflect
this.
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200703103840.333732-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Disable Left and Right Spk pin after boot so that sof can get
suspended.
This follows the same logic added to another machine driver with
commit 94d2d08974 ("ASoC: Intel: Boards: tgl_max98373: add dai_trigger function")
Signed-off-by: randerwang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200708203215.231776-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reflect Kconfig changes and add both SoundWire and I2C modes
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200708203215.231776-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare support for SoundWire, let's first split the I2C and common
parts. No new functionality, just indents and formatting to make
checkpatch happy.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200708203215.231776-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SOF is used, the normal links are converted into DPCM ones. This
generates an error
[ 58.276668] bdw-rt5677 bdw-rt5677: CPU DAI spi-RT5677AA:00 for rtd
Wake on Voice does not support playback
[ 58.276676] bdw-rt5677 bdw-rt5677: ASoC: can't create pcm Wake on
Voice :-22
Fix by forcing the capture direction.
Fixes: b73287f0b0 ('ASoC: soc-pcm: dpcm: fix playback/capture checks')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Link: https://lore.kernel.org/r/20200707210439.115300-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if the ctx->spkamp is not recognized an error message is
reported but the code continues to set up the device with uninitialized
variables such as the number of widgets. Fix this by returning -EINVAL
for unrecognized speaker amplifier types.
Fixes: e1435a1feb ("ASoC: Intel: bxt-da7219-max98357a: support MAX98390 speaker amp")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Addresses-Coverity: ("Uninitialized scalar variable")
Link: https://lore.kernel.org/r/20200702114835.37889-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support MAX98390 speaker amplifier on cometlake platform. Driver now
detects amplifier type in the probe function and installs corresponding
controls and DAPM widgets/routes in the late_probe function.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1593596211-28344-1-git-send-email-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default mode for SSP configuration is TDM 4 slot and so far we were
using this for the bus format on cht-bsw-rt56732 boards.
One board, the Lenovo Miix 2 10 uses not 1 but 2 codecs connected to SSP2.
The second piggy-backed, output-only codec is inside the keyboard-dock
(which has extra speakers). Unlike the main rt5672 codec, we cannot
configure this codec, it is hard coded to use 2 channel 24 bit I2S.
Using 4 channel TDM leads to the dock speakers codec (which listens in on
the data send from the SSP to the rt5672 codec) emiting horribly distorted
sound.
Since we only support 2 channels anyways, there is no need for TDM on any
cht-bsw-rt5672 designs. So we can simply use I2S 2ch everywhere.
This commit fixes the Lenovo Miix 2 10 dock speakers issue by changing
the bus format set in cht_codec_fixup() to I2S 2 channel.
This change has been tested on the following devices with a rt5672 codec:
Lenovo Miix 2 10
Lenovo Thinkpad 8
Lenovo Thinkpad 10 (gen 1)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786723
Link: https://lore.kernel.org/r/20200628155231.71089-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add max98373-sdw helper function, which configures 2x MAX98373 codecs to
Link1. This patch shares code between the I2S and SoundWire modes of
MAX98373 and adds the trigger already added for I2S.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200625192620.4312-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates tx_mask, so that (0-3)slots are reserved for
Maxim amps to feedback data.
V0->slot0,
I0->slot1,
V1->slot2,
I1->slot3.
also update slot_width in tdm configuration to 24 as the BE
configuration is 24 in topology.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_card_prelinks() is a common API to walk through each prelink
in the card.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the cml_rt1011_rt5682_dailink[].codecs pointer is overridden by
a quirk with a devm allocated structure and the probe is deferred,
in the next probe we will see an use-after-free condition
(verified with KASAN). This can be avoided by using statically allocated
configurations - which simplifies the code quite a bit as well.
KASAN issue fixed.
[ 23.301373] cml_rt1011_rt5682 cml_rt1011_rt5682: sof_rt1011_quirk = f
[ 23.301875] ==================================================================
[ 23.302018] BUG: KASAN: use-after-free in snd_cml_rt1011_probe+0x23a/0x3d0 [snd_soc_cml_rt1011_rt5682]
[ 23.302178] Read of size 8 at addr ffff8881ec6acae0 by task kworker/0:2/105
[ 23.302320] CPU: 0 PID: 105 Comm: kworker/0:2 Not tainted 5.7.0-rc7-test+ #3
[ 23.302322] Hardware name: Google Helios/Helios, BIOS 01/21/2020
[ 23.302329] Workqueue: events deferred_probe_work_func
[ 23.302331] Call Trace:
[ 23.302339] dump_stack+0x76/0xa0
[ 23.302345] print_address_description.constprop.0.cold+0xd3/0x43e
[ 23.302351] ? _raw_spin_lock_irqsave+0x7b/0xd0
[ 23.302355] ? _raw_spin_trylock_bh+0xf0/0xf0
[ 23.302362] ? snd_cml_rt1011_probe+0x23a/0x3d0 [snd_soc_cml_rt1011_rt5682]
[ 23.302365] __kasan_report.cold+0x37/0x86
[ 23.302371] ? snd_cml_rt1011_probe+0x23a/0x3d0 [snd_soc_cml_rt1011_rt5682]
[ 23.302375] kasan_report+0x38/0x50
[ 23.302382] snd_cml_rt1011_probe+0x23a/0x3d0 [snd_soc_cml_rt1011_rt5682]
[ 23.302389] platform_drv_probe+0x66/0xc0
Fixes: 629ba12e99 ("ASoC: Intel: boards: split woofer and tweeter support")
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for max98360a speaker amp on SSP1 and ALC5682 on SSP0
for jsl+ platform.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX_98373_DEV0_NAME is the Right speaker and MAX_98373_DEV1_NAME is the
Left speaker, hence updating the comments for max98373 dailink components
accordingly.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Speaker amplifier feedback is not modeled as being dependent on any
active output. Even when there is no playback happening, parts of the
graph, specifically the IV sense->speaker protection->output remains
active and this prevents the DSP from entering low-power states.
This patch suggests a machine driver level approach where the speaker
pins are enabled/disabled dynamically depending on stream start/stop
events. DPAM graph representations show the feedback loop is indeed
disabled and low-power states can be reached.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need an explicit cast, using the right format is simple
enough.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During the bring-up of new platforms, or to take care of specific
hardware reworks, it's useful to add a kernel parameter to override
the default DMI-based quirks.
For example, adding the following line in a .conf file in
/etc/modprobe.d/ will change the default quirk and log the changes if
dynamic debug is enabled.
options snd_soc_sof_sdw quirk=0x802
[ 735.025785] sof_sdw sof_sdw: Overriding quirk 0x10 => 0x802
[ 735.025787] sof_sdw sof_sdw: quirk realtek,jack-detect-source 2
[ 735.025790] sof_sdw sof_sdw: quirk SOF_RT715_DAI_ID_FIX enabled
Tested on ICL RVP with add-on board instead of default codec.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is required for ASoC cards. Not setting it will result in a
module->name pointer being NULL and generate problems such as
cat /proc/asound/modules
0 (efault)
Fixes: 76016322ec ('ASoC: Intel: Add Broxton-P machine driver')
Reported-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is required for ASoC cards. Not setting it will result in a
module->name pointer being NULL and generate problems such as
cat /proc/asound/modules
0 (efault)
Fixes: 52db12d193 ('ASoC: Intel: boards: add sof_sdw machine driver')
Reported-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is required for ASoC cards. Not setting it will result in a
module->name pointer being NULL and generate problems such as
cat /proc/asound/modules
0 (efault)
Fixes: 17fe95d6df ('ASoC: Intel: boards: Add CML m/c using RT1011 and RT5682')
Reported-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200625191308.3322-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing the machine driver, the rt5682 jack handler will oops if jack
detection is not disabled. The jack can be disabled in the dai link's exit().
This is symmetrical change as jack is enabled in init().
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200622154241.29053-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move disabling jack from platform driver's remove() to dai link's exit().
This is symmetrical change as jack is enabled in init().
Signed-off-by: Fred Oh <fred.oh@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200622154241.29053-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod handling is inspired from the bdw-rt5677 code. Apply same
fix to avoid reference count issue while removing modules for
consistency.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Link: https://lore.kernel.org/r/20200622154241.29053-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The mainline code currently prevents modules from being removed.
The BE dailink .init() function calls devm_gpiod_get() using the codec
component device as argument. When the machine driver is removed, the
references to the gpiod are not released, and it's not possible to
remove the codec driver module - which is the only entity which could
free the gpiod.
This conceptual deadlock can be avoided by invoking gpiod_get() in the
.init() callback, and calling gpiod_put() in the exit() callback.
Tested on SAMUS Chromebook with SOF driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Link: https://lore.kernel.org/r/20200622154241.29053-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Blindly adding an sof- prefix to the card name is not user friendly
and causes UCM issues with a driver name truncated to 16 characters.
Simplify to use "sof-bdw <codec_name>" pattern for all Broadwell
machine drivers. The sof- prefix is added by the core. A generic "SOF"
driver name is used, and UCMv2 will detect the configuration for this
driver by testing the card name.
Legacy uses are unmodified.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200617165616.18511-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Blindly adding an sof- prefix to the card name is not user friendly
and causes UCM issues with a driver name truncated to 16 characters.
Simplify to use "sof-bytcht <codec_name>" pattern for all cht* machine
drivers. The sof- prefix is added by the core. A generic "SOF" driver
name is used, and UCMv2 will detect the configuration for this driver
by testing the card name.
Legacy uses are unmodified.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200617165616.18511-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Blindly adding an sof- prefix to the card name is not user friendly
and causes UCM issues with a driver name truncated to 16 characters.
Simplify to use "sof-bytcht <codec_name>" pattern for all byt* machine
drivers. The sof- prefix is added by the core. A generic "SOF" driver
name is used, and UCMv2 will detect the configuration for this driver
by testing the card name.
Legacy uses are unmodified.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200617165616.18511-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We already have two configurations for CometLake, and a third one
coming. On other platforms, we used a single Kconfig option, so we
should follow the same trend by merging the two cases in a backwards
compatible way.
The backwards compatibility is handled by overloading the COMETLAKE_LP
kconfig as COMETLAKE. In practice we've never seen a case where
COMETLAKE_H is not selected along with COMETLAKE_LP, so keeping one
of the two is enough.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200617164755.18104-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We've had a couple of changes that introduce regressions with the
multi-cpu DAI solutions, and while trying to fix them we found
additional inconsistencies that should also go to stable branches.
Bard Liao (1):
ASoC: core: only convert non DPCM link to DPCM link
Pierre-Louis Bossart (3):
ASoC: soc-pcm: dpcm: fix playback/capture checks
ASoC: Intel: boards: replace capture_only by dpcm_capture
ASoC: SOF: nocodec: conditionally set dpcm_capture/dpcm_playback flags
sound/soc/intel/boards/glk_rt5682_max98357a.c | 2 +-
sound/soc/intel/boards/kbl_da7219_max98927.c | 4 +-
sound/soc/intel/boards/kbl_rt5663_max98927.c | 2 +-
.../intel/boards/kbl_rt5663_rt5514_max98927.c | 2 +-
sound/soc/soc-core.c | 22 ++++++++--
sound/soc/soc-pcm.c | 44 ++++++++++++++-----
sound/soc/sof/nocodec.c | 6 ++-
7 files changed, 62 insertions(+), 20 deletions(-)
base-commit: 8a9144c1cf
--
2.20.1
The Toshiba Encore WT10-A tablet almost fully works with the default
settings for Bay Trail CR devices. The only issue is that it uses a
digital mic. connected the the DMIC1 input instead of an analog mic.
Add a quirk for this model using the default settings with the input-map
replaced with BYT_RT5640_DMIC1_MAP.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200608204634.93407-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not clear why specific FE dailinks use capture_only flags, likely
blind copy/paste from Chromebook driver to the other. Replace by
dpcm_capture, this will make future alignment and removal of flags
easier.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608194415.4663-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As CONFIG_SND_HDA_CODEC_HDMI is always enabled in sof_pcm512x,
let's remove the test of CONFIG_SND_HDA_CODEC_HDMI in the
sof_pcm512x driver.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200529193547.6077-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC is always enabled in sof-soundwire
driver, let's remove the test of CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC
in the code.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200529193547.6077-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver uses common hdmi, SND_SOC_SOF_HDA_AUDIO_CODEC is required
to be enabled. Otherwise, the legacy hda codec driver will not be used.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200529193547.6077-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With SND_SOC_AMD_RV_RT5682_MACH using the i2c version of the
driver, we can easily get a build failure when I2C is built-in
but soundwire is not:
WARNING: unmet direct dependencies detected for SND_SOC_RT5682
Depends on [m]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && (I2C [=y] || SOUNDWIRE [=m]) && (SOUNDWIRE [=m] || !SOUNDWIRE [=m]) && (I2C [=y] || !I2C [=y])
Selected by [y]:
- SND_SOC_AMD_RV_RT5682_MACH [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SND_SOC_AMD_ACP3x [=y] && I2C [=y] && CROS_EC [=y]
Selected by [m]:
- SND_SOC_RT5682_SDW [=m] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && SOUNDWIRE [=m] && (I2C [=y] || !I2C [=y])
Rework the driver to have three separate modules, with the
main driver just dealing with the common bits and the actual
initialization as part of i2c and sdw specific modules.
The conversion is fairly mechanical to keep it easy to review,
i.e. it moves code around with the minimal required renaming
and changes.
Fixes: 6b8e4e7db3 ("ASoC: amd: Add machine driver for Raven based platform")
Fixes: fd443a20c2 ("ASoC: rt5682: fix I2C/Soundwire dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200528091851.2889754-1-arnd@arndb.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add required .pm_ops to support suspend/resume on baytrail/cherrytrail
machines.
This .pm_ops is conditionally-added to avoid impacting the legacy
driver where power management is handled differently.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200526203640.25980-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Low-power playback was never enabled on Baytrail devices, remove what
looks like copy/paste from other machine drivers which were never
submitted upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200526203640.25980-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Toshiba Encore WT8-A tablet almost fully works with the default
settings for non-CR Bay Trail devices. The only problem is that its
jack-detect switch is not inverted (it is active high instead of
the normal active low).
Add a quirk for this model using the default settings +
BYT_RT5640_JD_NOT_INV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200518072416.5348-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use same mapping as in all other machine drivers:
BTN_0 : KEY_PLAYPAUSE
BTN_1 : KEY_VOICECOMMAND
BTN_2 : KEY_VOLUMEUP
BTN_3 : KEY_VOLUMEDOWN
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200515210731.10942-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use same mapping as in all other machine drivers:
BTN_0 : KEY_PLAYPAUSE
BTN_1 : KEY_VOICECOMMAND
BTN_2 : KEY_VOLUMEUP
BTN_3 : KEY_VOLUMEDOWN
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200515210731.10942-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use same mapping as in all other machine drivers:
BTN_0 : KEY_PLAYPAUSE
BTN_1 : KEY_VOICECOMMAND
BTN_2 : KEY_VOLUMEUP
BTN_3 : KEY_VOLUMEDOWN
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200515210731.10942-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The component string attributes are separated by spaces, not commas.
Fixes: b1ca2f63e2 ("ASoC: Intel: sof_sdw: add amp number in components string for ucm")
Reported-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200515210731.10942-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the ambiguity with GPL-2.0 and use an explicit GPL-2.0-only
tag.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200501145850.15178-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new machine driver to interface with WM8804. The code is based
on settings found in sound/soc/bcm/hifiberry-digi.c in the Raspberry
PI tree.
Tested on Up2 with Digi+ IO (capture+playback) and Digi+ PRO (playback
with two local oscillators supported). The codec is clock master in
both cases.
Capture support has known clocking restrictions: the transmitter needs
to be active for the clock recovery, the "Tx Source" mixer set to
"S/PDIF RX". Playback will only work while capture is active.
When Capture is not desired, or when there is no RX connector, the "Tx
Source" mixer should be set to "AIF"
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200501151625.17820-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing the SOF module, the RT286 jack detect
handler will oops if jack detection is not disabled.
Disable the jack in the machine driver remove callback
to prevent this. This fix is only for SOF support and is
not needed for earlier versions.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200427162953.21107-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series provides the following updtes to the Intel machine driver
Kconfig:
1. The first patch adds the explicit dependency on GPIOLIB when
SND_SOC_DMIC is selected.
2. SND_SOC_SOF_HDA_AUDIO_CODEC is required for using the legacy
HDA codec driver for HDMI support in SOF. The last 3 three patches
make the required changes to account for this.
Libin Yang (3):
ASoC: intel: add depends on SND_SOC_SOF_HDA_AUDIO_CODEC for common
hdmi
ASoC: sof-sdw: remove CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC condition
ASoC: sof_pcm512x: remove CONFIG_SND_HDA_CODEC_HDMI condition
Pierre-Louis Bossart (1):
ASoC: Intel: boards: add explicit dependency on GPIOLIB when DMIC is
used
sound/soc/intel/boards/Kconfig | 51 ++++++++++++++-------------
sound/soc/intel/boards/sof_pcm512x.c | 9 -----
sound/soc/intel/boards/sof_sdw.c | 8 -----
sound/soc/intel/boards/sof_sdw_hdmi.c | 7 ----
4 files changed, 26 insertions(+), 49 deletions(-)
--
2.17.1
BDW boards using this machine driver supports only stereo capture and
playback. Implement a constraint to enforce it.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1588007614-25061-4-git-send-email-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BDW boards using this machine driver supports only 2 or 4-channel capture.
Implement a constraint to enforce it.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1588007614-25061-3-git-send-email-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BDW boards using this machine driver supports only stereo capture and
playback. Implement a constraint to enforce it.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1588007614-25061-2-git-send-email-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DMIC depends on GPIOLIB, so let's add the dependency before
selecting SND_SOC_DMIC.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200427165211.23463-2-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The number of speaker amplifiers may vary between platforms. UCM
needs to check amp number to include different configuration files.
This patch keeps track of the number of speaker amplifiers and
stores it in components string of the card.
Tested on Comet Lake platforms.
Signed-off-by: randerwang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200419183509.4134-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent fix for jack detection caused a regression on systems with HDA
audio codec but no HDMI/DP audio via i915 graphics, leading to a kernel
oops at device probe. On these systems, HDA bus instance lookup fails,
as the first ASoC runtime of the card is connected to a dummy codec
(as no HDMI codec is present).
Fixes: 3a24f135e6 ("ASoC: intel/skl/hda - set autosuspend timeout for hda codecs")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200420205431.13070-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DMIC endpoint widget and route to make DMIC DAPM routes completed,
to make DAPM Power Management works for DMIC streams.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200409185827.16255-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Init codecs which belong to the same group id on all links.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200409185827.16255-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the support of Intel Elkhart Lake with
Realtek rt5660 codec.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Muhammad Nazif Bin Mohd Borhan <muhammad.nazif.mohd.borhan@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200409185827.16255-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On some Lenovo and HP laptops, if both codec driver and SOF driver
are in runtime suspend mode, we plug a headset to the audio jack,
the headphone could be detected but Mic couldn't.
That is because when plugging, the headphone triggers a unsol event
first, and about 0.7s later (on the Lenovo X1 Carbon 7th), the Mic
triggers a unsol event. But if the codec driver enters runtime suspend
within 0.7s, the Mic can't trigger the unsol event.
If we don't set autosuspend_delay to a non-zero value for the hda codec
driver, it will enter runtime suspend immediately after the headphone
triggers the unsol event.
Follow the sequence of legacy hda driver and set a autosuspend delay
of 1sec after card registration (refer to pci/hda/hda_intel.c and
pci/hda/hda_codec.c).
Co-developed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Co-developed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Clarex Zhou <clarex.zhou@intel.com>
Link: https://lore.kernel.org/r/20200409185827.16255-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add dmic16k BE dailink for keyword detection support, FE is
added in topology tplg file.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200409185827.16255-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MPMAN MPWIN895CL tablet almost fully works with out default settings.
The only problem is that it has only 1 speaker so any sounds only playing
on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200405133726.24154-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit:
ASoC: soc-core: care .ignore_suspend for Component suspend
function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend'
flag for dai links. While BE dai link for System Pin is
supposed to follow standard suspend-resume flow, appended
'ignore_suspend' flag disturbs that flow and causes audio to break
right after resume. Remove the flag to address this.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200319204947.18963-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit:
ASoC: soc-core: care .ignore_suspend for Component suspend
function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend'
flag for dai links. While BE dai link for System Pin is
supposed to follow standard suspend-resume flow, appended
'ignore_suspend' flag disturbs that flow and causes audio to break
right after resume. Remove the flag to address this.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200319204947.18963-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit:
ASoC: soc-core: care .ignore_suspend for Component suspend
function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend'
flag for dai links. While BE dai link for System Pin is
supposed to follow standard suspend-resume flow, appended
'ignore_suspend' flag disturbs that flow and causes audio to break
right after resume. Remove the flag to address this.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200319204947.18963-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of commit:
ASoC: soc-core: care .ignore_suspend for Component suspend
function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend'
flag for dai links. While BE dai link for System Pin is
supposed to follow standard suspend-resume flow, appended
'ignore_suspend' flag disturbs that flow and causes audio to break
right after resume. Remove the flag to address this.
Link to first message in conversation:
https://lkml.org/lkml/2020/3/18/54
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200319204947.18963-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Google Volteer device. As per new unified soundwire machine
driver, add rt5682-sdw helper function, which configures codec to Link0.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Link: https://lore.kernel.org/r/20200325220746.29601-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This machine driver provides support for different configurations:
RT700, RT711, RT1308 (1x and 2x, I2S or SoundWire mode), and RT715
CometLake, Icelake, TigerLake.
PDM digital microphones
HDMI
To avoid introducing one driver per configuration, this common machine
driver relies on platform-specific information, tables and quirks to
dynamically create the relevant dailinks.
Unlike a lot of machine drivers, we use different DAI links for
SoundWire capture and playback since the Cadence PDIs can do capture
OR playback, not both simultaneously.
For each configuration, the card component string is updated so that UCM
can select the relevant parts.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200325220746.29601-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch does the below:
1. Adds the driver data and updates quirk info for TGL
with Max98373 speaker amp and ALC5682 headset codec.
2. Added max98373 speaker related code to common file for re-use.
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200325213245.28247-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add "Spk Switch" and associated widget, route to max98360a
speaker amp for power saving, also remove the speaker_amp_init()
callback with complete separated tables for max98373 and max98360a.
Signed-off-by: Bhat, Uday M <uday.m.bhat@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Link: https://lore.kernel.org/r/20200325213245.28247-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Without the dynamic flag to allow runtime routing, the card cannot
probe on chromebooks because SOF is constantly waiting for the link.
Adding flag back to allow upstream kernels to work on rt5682 based
chromebooks since SOF can now ignore the hard coded front end.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200325213245.28247-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent series of patches targeting broadwell boards, while enabling
SOF, changed behavior for non-SOF solutions. In essence replacing
platform 'dummy' with actual 'platform' causes redundant stream
initialization to occur during audio start. hw_params for haswell-pcm
destroys initial stream right after its creation - only to recreate it
again from proceed from there.
While harmless so far, this flow isn't right and should be corrected.
The actual need for dummy components for SSP0 link is questionable but
that issue is subject for another series.
Fixes: a40acc6bfc ("ASoC: Intel: bdw-rt5650: change cpu_dai and platform components for SOF")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200325131611.545-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent series of patches targeting broadwell boards, while enabling
SOF, changed behavior for non-SOF solutions. In essence replacing
platform 'dummy' with actual 'platform' causes redundant stream
initialization to occur during audio start. hw_params for haswell-pcm
destroys initial stream right after its creation - only to recreate it
again from proceed from there.
While harmless so far, this flow isn't right and should be corrected.
The actual need for dummy components for SSP0 link is questionable but
that issue is subject for another series.
Fixes: 4865bde187 ("ASoC: Intel: bdw-rt5677: change cpu_dai and platform components for SOF")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200325131611.545-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent series of patches targeting broadwell boards, while enabling
SOF, changed behavior for non-SOF solutions. In essence replacing
platform 'dummy' with actual 'platform' causes redundant stream
initialization to occur during audio start. hw_params for haswell-pcm
destroys initial stream right after its creation - only to recreate it
again from proceed from there.
While harmless so far, this flow isn't correct and should be corrected.
The actual need for dummy components for SSP0 link is questionable but
that issue is subject for another series.
Link to first message in conversation:
https://lkml.org/lkml/2020/3/18/54
Fixes: 64df6afa0d ("ASoC: Intel: broadwell: change cpu_dai and platform components for SOF")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200325131611.545-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We've removed GFP_ATOMIC in all machine drivers and somehow this keeps
coming back due to copy-paste. Move to GFP_KERNEL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Maxim MAX98360A plug-and-play Class-D amplifier support on SSP1,
new card ID is sofda7219max98360a, name sof-da7219max98360a.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a clumsy structure member dereference in all machine drivers.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make HDMI optional for APL and later platforms. If no HDMI codec
is found on the HDA bus, the graphics side driver is missing or
correct codec driver is not part of kernel build, codec_mask
reflects this and HDMI is disabled. The DSP topology will still
have the links for HDMI, so connect these to dummy codec to avoid
failures in topology loading.
This change also fixes a kernel oops that was triggered if
sof_pcm512x was used with SOF configured to use hdac-hdmi (can be
done via "use_common_hdmi=0" or by selecting
CONFIG_SND_SOC_SOF_HDA_COMMON_HDMI_CODEC=n). This is not a supported
configuration.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having a reverse dependency to a config that has its own additional
dependencies, is generally not recommended. And this applies to
select statements for SND_HDA_CODEC_HDMI, e.g. the case where SND_HDA
and SND_SOC_SOF_HDA are built as modules, but the machine driver is
built-in, leading to compile errors (reported as
i386-randconfig-e003-20200206).
Give up on trying to define different dependencies based on SOF/SST
selection, and simply add a "depends on" for SND_HDA_CODEC_HDMI. This
fixes the issue with randconfigs. Only downside is that SND_HDA_CODEC_HDMI
may be built unnecessarily in some cases, but this seems like the lesser
evil.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having a reverse dependency to a config that has its own additional
dependencies, is generally not recommended. And this applies to
select statements for SND_HDA_CODEC_HDMI, e.g. the case where SND_HDA
and SND_SOC_SOF_HDA are built as modules, but the machine driver is
built-in, leading to compile errors (reported as
i386-randconfig-e003-20200206).
Give up on trying to define different dependencies based on SOF/SST
selection, and simply add a "depends on" for SND_HDA_CODEC_HDMI. This
fixes the issue with randconfigs. Only downside is that SND_HDA_CODEC_HDMI
may be built unnecessarily in some cases, but this seems like the lesser
evil.
Fixes: aa2b4a5 ('ASoC: Intel: boards: fix incorrect HDMI Kconfig dependency')
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312194859.4051-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for multiple platforms, e.g. Apollolake based, using the
pcm512x audio codec.
The SOF developers and CI rely on the Up^2 and Hifiberry DAC+ boards
based on this codec for tests.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200129223603.2569-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of updates for bugs fixed since the initial pull
request, the most important one being the addition of COMMON_CLK
for wcd934x which is needed for MFD to be merged.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl46jnATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FfTB/9pn+BR2PZWE349/Etdj4Tb0mHO3mfG
7sptuPYCXrFRJ82HPcSIIY8nUMBP+lYciIBE4Dn09QDxwPALFuEuzcM7XmJpJIKJ
Vg9ooyYC4/59ijQJXFGR61Xaf30PcvdxE1sC3+SEt6ROn9C/whZHFzpnPJgmeFbq
LIVI2ne/QpPQ+fozvUjkr8nOrEbLIhH6DeCRKExmQ5PYnM7fO//s51HmCUOAxQwJ
FvEH2NCZwvGA43xSYeAdWfE1C3DgdEIT1VKEfeA+Va2tjwPz64mtA6xbaNW99xV6
5/ii/c1x3Yjvy+F6IAqrmwCDZWQJ+xIgy4nbNLd2V8t1alYKWz22aVOr
=qO+a
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.6
A collection of updates for bugs fixed since the initial pull
request, the most important one being the addition of COMMON_CLK
for wcd934x which is needed for MFD to be merged.
Multiple Intel ASoC machine drivers repeat the same pattern in their
.late_probe() methods: they first check whether the common HDMI codec
driver is used, if not, they proceed by linking the legacy HDMI
driver to each HDMI port. While doing that they use some
inconsistent code:
1. after the loop they check, whether the list contained at least one
element and if not, they return an error. However, the earlier
code to use the common HDMI driver uses the first element of the
same list without checking. To fix this we move the check to the
top of the function.
2. some of those .late_probe() implementations execute code, only
needed for the common HDMI driver, before checking, whether the
driver is used. Move the code to after the check.
3. Some of those functions also perform a redundant initialisation of
the "err" variable.
This patch fixes those issues.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
