currenlty wcd938x has only soundwire interface and depends on
symbols from wcd938x soundwire module, so make this dependency
explicit in Kconfig
Without this one of the randconfig endup setting
CONFIG_SND_SOC_WCD938X=y
CONFIG_SND_SOC_WCD938X_SDW=m
resulting in some undefined reference to wcd938x_sdw* symbols.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210713140417.23693-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5631 does not like multi-write accesses, avoid them. This fixes:
rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121
errors on resume from suspend (and all registers after the registers in
the error not being synced).
Inspired by commit 2d30e9494f ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS2505/TAS2521 does support up to two channels, LEFT and RIGHT,
which are being alternated on the audio data bus by Word Clock, WCLK.
This is documented in TI slau472 2.7.1 Digital Audio Interface. Note
that both the LEFT and RIGHT channels are only used for audio INPUT,
while only the LEFT channel is used for audio OUTPUT.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091229.56443-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The control fw_name is always directly assigned from the wm_adsp_fw_text
array, so it isn't necessary to compare the actual strings just the
pointer values.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the tlv320aic31xx driver has regulator support but does not
enable the regulators during probe, deferring this until something causes
ASoC to make the card active. It does put the device into cache only mode
but only when the component level probe is called, however if interrupts
are in use the driver will access the regmap before then which if the
regulators are not powered on would cause I/O problems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210707160234.16253-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
None of the TAS2505 outputs are stereo, do not pretend they are by
implementing them using SOC*DOUBLE* macros referencing the same
register twice, use SOC*SINGLE* instead. Fix volume ranges and mute
control for the codec according to datasheet.
Fixes: b4525b6196 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091255.56502-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
These are backwards from Table 7-71 of the TLV320AIC3100 spec [1].
This was broken in 12eb4d66ba when BCLK_MASTER and WCLK_MASTER
were converted from 0x08 and 0x04 to BIT(2) and BIT(3), respectively.
-#define AIC31XX_BCLK_MASTER 0x08
-#define AIC31XX_WCLK_MASTER 0x04
+#define AIC31XX_BCLK_MASTER BIT(2)
+#define AIC31XX_WCLK_MASTER BIT(3)
Probably just a typo since the defines were not listed in bit order.
[1] https://www.ti.com/lit/gpn/tlv320aic3100
Signed-off-by: Kyle Russell <bkylerussell@gmail.com>
Link: https://lore.kernel.org/r/20210622010941.241386-1-bkylerussell@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting the Halo core it is advised to also write the core reset
bit, this ensures the part starts up in the appropriate state. Omitting
this doesn't cause issues on most parts but cs40l25 requires it and
it is advised on all Halo parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When wm_coeff_tlv_get was updated it was accidentally switch to the _raw
version of the helper causing it to ignore the current DSP state it
should be checking. Switch the code back to the correct helper so that
users can't read the controls when they arn't available.
Fixes: 73ecf1a673 ("ASoC: wm_adsp: Correct cache handling of new kernel control API")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210626155941.12251-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit dc98f1d we removed the zte zx sound drivers but there
was a dangling Kconfig left around for the codec so fix this.
Fixes: dc98f1d655 ("ASoC: remove zte zx drivers")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210627105955.3410015-1-pbrobinson@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
this is v2 from my patchset that add support for the TAS2505 to the tlv320aic32x4 driver.
kind regards,
Claudius
Changes from v1:
- clarified commit message of first patch, which add the type value to the struct
- removed unnecessary code to put and get speaker volume
- removed 'Gain' from 'HP Driver Playback Volume' control
- fixed rebase issues
Claudius Heine (3):
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
.../bindings/sound/tlv320aic32x4.txt | 1 +
sound/soc/codecs/tlv320aic32x4-i2c.c | 22 ++-
sound/soc/codecs/tlv320aic32x4-spi.c | 23 ++-
sound/soc/codecs/tlv320aic32x4.c | 139 +++++++++++++++++-
sound/soc/codecs/tlv320aic32x4.h | 10 ++
5 files changed, 186 insertions(+), 9 deletions(-)
base-commit: 70585216fe
--
2.32.0
This adds support for TAS2505 and TAS2521 to the tlv320aic32x4 driver.
The TAS2505 seems to be a stripped down version of the TLV320AIC32X4 so
it makes sense to handle them in the same driver.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-3-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
While this driver can already handle different device variants, the
variant information cannot be used in the driver code and therefor
cannot have different code paths depending on the device variant.
This change adds a `type` value into the `aic32x4_priv` structure, that
contains a device variant identifier, which was set when the driver was
bound to the device.
Signed-off-by: Claudius Heine <ch@denx.de>
Link: https://lore.kernel.org/r/20210617085230.1851503-2-ch@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below two uninitialized symbol warnings
warning:
sound/soc/codecs/wcd938x.c:2092 wcd938x_tx_swr_ctrl()
error: uninitialized symbol 'rate'
sound/soc/codecs/wcd938x.c:2189 wcd938x_tx_channel_config()
error: uninitialized symbol 'reg'.
First one my brining in check to already existing if condition and
second one by adding a default switch case to avoid any access to reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210621134502.19537-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes below
warning: unused variable wcd938x_dt_match
by placing device match table under CONFIG_OF
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210621134502.19537-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards use different circuits for jack detection.
This patch adds two modes as below
1. JD2/2 ports/external resister 100k
2. JD2/1 port/JD voltage 1.8V
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210617090822.16960-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-sdca-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The code is slightly different from the other codecs since the
interrupt callback deals with the SDCA interrupts, leading to a much
larger section that's protected by the mutex. The SoundWire interrupt
scheme requires a read after clearing a status, it's not clear from
the specifications what would happen if SDCA interrupts are disabled
in the middle of the sequence, so the entire interrupt status
read/write is kept as is, even if in the end we discard the
information.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the initial driver we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT5682-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
The Fixes tag points to a 5.10 commit, there's no need to propagate
this change to earlier upstream versions.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 4a55000722 ('ASoC: codecs: rt*.c: remove useless pointer cast')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error. While we
did not see this IO error on RT711-based platforms, the code pattern
is similar to the RT700 case where the IO error was noted, so the fix
is added for consistency.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 501ef01339 ('ASoC: rt711: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In previous commits we cancelled deferred work, but there is still a
window of time where a new interrupt could result in new deferred work
executed after the link is disabled, leading to an IO error.
This patch uses an 'disable_irq_lock' mutex to prevent new interrupts
from happening after the start of the system suspend. The choice of a
mutex v. a spinlock is mainly due to the time required to clear
interrupts, which requires a command to be transmitted by the
SoundWire host IP and acknowledged with an interrupt. The
'interrupt_callback' routine is also not meant to be called from an
interrupt context.
An additional 'disable_irq' flag prevents race conditions where the
status changes before the interrupts are disabled, but the workqueue
handling status changes is scheduled after the completion of the
system suspend. On resume the interrupts are re-enabled already by the
io_init routine so we only clear the flag.
BugLink: https://github.com/thesofproject/linux/issues/2943
Fixes: 5f2df2a458 ('ASoC: rt700: wait for the delayed work to finish when the system suspends')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210614180815.153711-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210602113643.3037374-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This symbol is not used outside of hdmi-codec.c, so marks it static.
Fix the following sparse warning:
sound/soc/codecs/hdmi-codec.c:750:25: warning: symbol
'hdmi_codec_controls' was not declared. Should it be static?
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1623822941-3077-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true/false
instead of 1/0.
Fix the following coccicheck warning:
./sound/soc/codecs/wcd938x.c:1190:9-10: WARNING: return of 0/1 in
function 'wcd938x_volatile_register' with return type bool.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1623811535-15841-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the following includecheck warnings:
./sound/soc/codecs/wcd938x.c: sound/soc.h is included more than once.
./sound/soc/codecs/wcd938x-sdw.c: sound/soc.h is included more than
once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1623822667-130511-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with cyclic dependency between snd_soc_wcd938x
and snd_soc_wcd938x_sdw modules.
Remove this cyclic dependency by handling them in respective modules.
Without this below error is reported during make modules_install
depmod: ERROR: Cycle detected: snd_soc_wcd938x -> snd_soc_wcd938x_sdw -> snd_soc_wcd938x
depmod: ERROR: Found 2 modules in dependency cycles!
Fixes: 0454422288 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210615132829.23067-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20210615113324.238837-1-pulehui@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Realtek rt5640 codec driver can be used with the generic sound card
drivers, so it should be selectable. For example, with the addition
of #sound-dai-cells = <0> property in DT, it can be used with simple and
graph card drivers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210612200650.1301661-1-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support for Qualcomm WCD938X codec.
Qualcomm WCD9380/WCD9385 Codec is a standalone Hi-Fi audio codec IC
connected over SoundWire. This device has two SoundWire devices, RX and
TX respectively supporting 4 x ADCs, ClassH, Ear, Aux PA, 2xHPH,
7 x TX diff inputs, 8 DMICs and MBHC.
Eventhough this device has two SoundWire devices, only tx device has
access to main codec Control/Status Registers!
For codec driver to be functional it would need both tx and rx Soundwire devices
to be up and this is taken care by using device component framework and device-links
are used to ensure proper pm dependencies. Ex tx does not enter suspend
before rx or codec is suspended.
This patchset along with other SoundWire patches on the list
have been tested on SM8250 MTP device.
Thanks,
srini
Changes since v8:
- moved Kconfig and Makefile changes to last patch as suggested by Mark
- removed array of enums and used static entries instead. Suggested by Mark
- return true if put succeeds, Suggested by Mark
- removed some unneeded semi-colons in switch
Srinivas Kandagatla (9):
ASoC: dt-bindings: wcd938x: add bindings for wcd938x
ASoC: codecs: wcd-clsh: add new version support
ASoC: codecs: wcd938x: add basic driver
ASoC: dt-bindings: wcd938x-sdw: add bindings for wcd938x-sdw
ASoC: codecs: wcd938x-sdw: add SoundWire driver
ASoC: codecs: wcd938x: add basic controls
ASoC: codecs: wcd938x: add playback dapm widgets
ASoC: codecs: wcd938x: add capture dapm widgets
ASoC: codecs: wcd938x: add audio routing and Kconfig
.../bindings/sound/qcom,wcd938x-sdw.yaml | 70 +
.../bindings/sound/qcom,wcd938x.yaml | 146 +
sound/soc/codecs/Kconfig | 14 +
sound/soc/codecs/Makefile | 4 +
sound/soc/codecs/wcd-clsh-v2.c | 348 +-
sound/soc/codecs/wcd-clsh-v2.h | 16 +
sound/soc/codecs/wcd938x-sdw.c | 315 ++
sound/soc/codecs/wcd938x.c | 3753 +++++++++++++++++
sound/soc/codecs/wcd938x.h | 720 ++++
9 files changed, 5376 insertions(+), 10 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x-sdw.yaml
create mode 100644 Documentation/devicetree/bindings/sound/qcom,wcd938x.yaml
create mode 100644 sound/soc/codecs/wcd938x-sdw.c
create mode 100644 sound/soc/codecs/wcd938x.c
create mode 100644 sound/soc/codecs/wcd938x.h
--
2.21.0
From WCD937X Class H controller has changed significantly, so add support
to this new version for WCD937X and WCD938X Codecs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210609090943.7896-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Eliminate the following coccicheck warning:
./sound/soc/codecs/wcd-mbhc-v2.c:990:2-3: Unneeded semicolon.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1623221171-105359-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
to support the HDMI Channel Mapping and IEC958 controls
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYMHitQAKCRDj7w1vZxhR
xQ40AP49z0mUifkpbyUvYwdmrUVlg2JEWSTOWaH3tp0kke/dBQEA1vYxdMimhFu3
SYKXxgtvlT7vL48vNYBxGbNuGQvzJw4=
=IWna
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDHK+QACgkQJNaLcl1U
h9DGHAf/ZhveHulV/2ysiFroyNxcp0PLT49/I/2AAyPhglREmbrXhWCALLcVf0ur
UqN2OlvdaiiozXHqsLrm5i1qKvz86659FPv8kEBpLyOgvCpsOu+HnjYk+EEJ2nDf
u8YDbXc5HZQ6bLD2cz/KRKPs7HlTtzq5yCn1tPsaNvcnOQ3/XnyeDo7XegIiah46
ts3mnOHTvYDujMehxIxMW0oe29pz6qibHynG4iNiEkVw0ZlBvHC4d0MWunSP8GpV
wrHt62K0xgrI5UU4ilpIXozUiFZGiFm9grPwZ6sXFGEvtSVLRUJebnCGe5ccgXQ5
4iNE9EClQHYZZm/vYpB4YxTPis1+bQ==
=k79R
-----END PGP SIGNATURE-----
Merge tag 'asoc-hdmi-codec-improvements-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into asoc-5.14
Improvements to the hdmi-codec driver and ALSA infrastructure around it
to support the HDMI Channel Mapping and IEC958 controls
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bit more commits than expected at this time, but likely it's the
last shot before the final. Many of changes are device-specific
fix-ups for various ASoC drivers, while a few usual HD-audio
quirks and a FireWire fix, as well as a couple of ALSA / ASoC
core fixes. All look nice and small, and nothing to scare much.
-----BEGIN PGP SIGNATURE-----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=ksfP
-----END PGP SIGNATURE-----
Merge tag 'sound-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bit more commits than expected at this time, but likely it's the
last shot before the final.
Many of changes are device-specific fix-ups for various ASoC drivers,
while a few usual HD-audio quirks and a FireWire fix, as well as a
couple of ALSA / ASoC core fixes.
All look nice and small, and nothing to scare much"
* tag 'sound-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix race of snd_seq_timer_open()
ALSA: hda/realtek: fix mute/micmute LEDs for HP ZBook Power G8
ALSA: hda/realtek: headphone and mic don't work on an Acer laptop
ASoC: qcom: lpass-cpu: Fix pop noise during audio capture begin
ALSA: firewire-lib: fix the context to call snd_pcm_stop_xrun()
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 840 Aero G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP EliteBook x360 1040 G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Elite Dragonfly G2
ASoC: rt5682: Fix the fast discharge for headset unplugging in soundwire mode
ASoC: tas2562: Fix TDM_CFG0_SAMPRATE values
ASoC: meson: gx-card: fix sound-dai dt schema
ASoC: AMD Renoir: Remove fix for DMI entry on Lenovo 2020 platforms
ASoC: AMD Renoir - add DMI entry for Lenovo 2020 AMD platforms
ASoC: SOF: reset enabled_cores state at suspend
ASoC: fsl-asoc-card: Set .owner attribute when registering card.
ASoC: topology: Fix spelling mistake "vesion" -> "version"
ASoC: rt5659: Fix the lost powers for the HDA header
ASoC: core: Fix Null-point-dereference in fmt_single_name()
The IEC958 status bit is usually set by the userspace after hw_params
has been called, so in order to use whatever is set by the userspace, we
need to implement the prepare hook. Let's add it to the hdmi_codec_ops,
and mandate that either prepare or hw_params is implemented.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210525132354.297468-6-maxime@cerno.tech
The IEC958 status bits can be exposed and modified by the userspace
through dedicated ALSA controls.
This patch implements those controls for the hdmi-codec driver. It
relies on a default value being setup at probe time that can later be
overridden by the control put.
The hw_params callback is then called with a buffer filled with the
proper bits for the current parameters being passed on so the underlying
driver can just reuse those bits as is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210525132354.297468-5-maxime@cerno.tech
One of the fixes reverted as part of the UMN fallout was actually fine,
however rather than undoing the revert the process that handled all this
stuff resulted in a patch which attempted to add extra error checks
instead. Unfortunately this new change wasn't really based on a good
understanding of the subsystem APIs and bypassed the usual patch flow
without ensuring it was reviewed by people with subsystem knowledge and
was merged as a fix rather than during the merge window.
The effect of the new fix is to upgrade what were previously warnings on
static data in the code to hard errors on that data. If this actually
happens then it would break existing systems, if it doesn't happen then
the change has no effect so this was not a safe change to apply as a fix
to the release candidates. Since the new code has not been tested and
doesn't in practice improve error handling revert it instead, and also
drop the original revert since the original fix was fine. This takes
the driver back to what it was in -rc1.
Fixes: 5e70b8e22b ("ASoC: rt5645: add error checking to rt5645_probe function")
Fixes: 1e0ce84215 ("Revert "ASoC: rt5645: fix a NULL pointer dereference")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210608160713.21040-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We're going to add more controls to support the IEC958 output, so let's
rework the control registration a bit to support more of them.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210525132354.297468-4-maxime@cerno.tech
A collection of fixes and device ID updates that have come up in the
past few -rcs, none of which stand out particularly.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmC/aSwACgkQJNaLcl1U
h9DNXAf+O+fzbVOkXxp/r3yUa2VF0Zdit0R8xIcUh0k7vd+MqYECaGaKqX9sAKbn
nQFNvzcdRjkiFFgmKpy6x2kJ/OXBJbRCvC5FfAAj2cJvzw4eN03wkqaa9JuEZX1e
uJ+Ny1PELMglHqmWNC9bWnudEJoaYxpssI14u+FjOWJPzIxXSxWSGQknIG4d8/Rh
BtifoTxWxsYIbKiiNhX6Ui5zdzRl5CeTLuKoKXBQRM0ivRwPuX0Y+VW/tsNiLUBT
yN/CEEuu+GZevdHRvWEW3FwK8y7W36gueEYe7o+SFQVgyyjESnhCRdhRvo7uvzrx
e1yVEe4ky0wbyhmBR+69SugYKqd1/A==
=tHOl
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.13-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.13
A collection of fixes and device ID updates that have come up in the
past few -rcs, none of which stand out particularly.
We currently only hangle rt711->regmap in rt711_sdca_io_init(), and
rt711->mbq_regmap is missing.
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SDW_SDCA_CTL() registers are used but are not set to readable.
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5682_DEVICE_ID is a volatile register, we can not read it in cache
only mode.
Fixes: 03f6fc6de9 ("ASoC: rt5682: Add the soundwire support")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device checking error should be a jump to pm_runtime_put_autosuspend()
as done before returning value.
Fixes: 867f8d18df ('ASoC: rt5682: fix getting the wrong device id when the suspend_stress_test')
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix clock stop prepare timeout issue (#2853).
The trigger of internal circuit which belong to
“SDCA preset stuffs” was not set correctly in previous driver,
which could block clock_stop_preparation state.
Add the correct register setting to fix it.
Fixes: 20d17057f0 ('ASoC: rt715-sdca: Add RT715 sdca vendor-specific driver')
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: d1ede0641b ('ASoC: rt715: add RT715 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers (was 'first_init')
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 20d17057f0 ('ASoC: rt715-sdca: Add RT715 sdca vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 320b8b0d13 ('ASoC: rt711: add rt711 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 7ad4d237e7 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 7d2a5f9ae4 ('ASoC: rt700: add rt700 codec driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 03f6fc6de9 ('ASoC: rt5682: Add the soundwire support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 2b719fd20f ('ASoC: rt1316: Add RT1316 SDCA vendor-specific driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
BugLink: https://github.com/thesofproject/linux/issues/2908
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: a87a6653a2 ('ASoC: rt1308-sdw: add rt1308 SdW amplifier driver')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers.
BugLink: https://github.com/thesofproject/linux/issues/2637
Fixes: 56a5b7910e ('ASoC: codecs: max98373: add SoundWire support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210607222239.582139-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark
These are v3 of "ASoC: adds new .get_fmt support",
but renamed Subject.
This is a little bit challenging patch-set.
The idea/code is almost same as v1 / v2.
v3 has "priority" support.
We need to set dai_link->dai_fmt to select CPU/Codec settings,
and it is selected by Sound Card Driver, today.
Because of it, Sound Card user need to know both CPU / Codec
available dai_fmt, and needs to select it.
For example simple-card / audio-graph case, it is selected by
"format" and "bitclock/frame-master/inversion" on DT.
But, it can be automatically selected if both CPU and Codec drivers
indicate it to ALSA SoC Framework, somehow.
By this patch, dai_fmt can be automatically selected from each
driver if both CPU / Codec driver had .auto_selectable_formats.
Automatically selectable *field* is depends on each drivers.
For example, some driver want to select format "automatically",
but want to select other fields "manually", because of complex limitation.
Or other example, in case of both CPU and Codec are possible to be
clock provider, but the quality was different.
In these case, user need/want to *manually* select each fields
from Sound Card driver.
It uses Sound Card specified fields preferentially, and try to select
non-specific fields from CPU and Codec driver settings if driver had
.auto_selectable_formats.
In other words, we can select all dai_fmt via Sound Card driver
same as before.
Select dai_fmt 100% automatically is very difficult and will be very complex,
but select automatically some fields only is very easy, I guess.
This patch-set is based on such assumption.
v1 -> v2
- Add more detail explanation on git-log, code, comment.
- Possible to be Clock/Frame provider is depends on driver's situation.
v2 -> v3
- has priority
- tidyup function explanation for snd_soc_dai_get_fmt()
- Each driver don't try to have SND_SOC_DAIFMT_CBx_CFx to avoid confusion
Link: https://lore.kernel.org/r/871rb3hypy.wl-kuninori.morimoto.gx@renesas.com
Link: https://lore.kernel.org/r/871racbx0w.wl-kuninori.morimoto.gx@renesas.com
Kuninori Morimoto (7):
ASoC: soc-core: move snd_soc_runtime_set_dai_fmt() to upside
ASoC: soc-core: add snd_soc_runtime_get_dai_fmt()
ASoC: ak4613: add .auto_selectable_formats support
ASoC: pcm3168a: add .auto_selectable_formats support
ASoC: rsnd: add .auto_selectable_formats support
ASoC: fsi: add .auto_selectable_formats support
ASoC: hdmi-codec: add .auto_selectable_formats support
include/sound/soc-dai.h | 55 +++++++
sound/soc/codecs/ak4613.c | 11 ++
sound/soc/codecs/hdmi-codec.c | 21 +++
sound/soc/codecs/pcm3168a.c | 26 +++
sound/soc/sh/fsi.c | 15 ++
sound/soc/sh/rcar/core.c | 31 +++-
sound/soc/soc-core.c | 288 ++++++++++++++++++++++++++--------
sound/soc/soc-dai.c | 63 ++++++++
sound/soc/soc-utils.c | 29 ++++
9 files changed, 475 insertions(+), 64 deletions(-)
--
2.25.1
The pointer node is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is
redundant and can be removed.
The function is missing a of_node_put on node, fix this by adding the call
before returning.
Addresses-Coverity: ("Unused value")
Fixes: 0d6a04da9b ("ASoC: Add Rockchip rk817 audio CODEC support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20210603113659.82031-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset adds support to MBHC(Multi Button Headset Control) block found in
Qualcomm WCD codecs. MBHC support headset type detection, both Mechanical and
electrical insert/removal detection along with 8 buttons detection,
Over current interrupts on HPHL/R, Impedance Measurements on HPHL/R.
Eventhough MBHC block supports things like OverCurrent detection, Currently its
reported as a kernel debug message. Should this be reported as an uevent to
userspace? like the way USB reports?
Any suggestions?
First patch adds a common mbhc driver and the second one wcd934x specific driver
changes along with sdm845 soundcard related changes.
Common wcd-mbhc-v2 driver should be reusable across multiple codecs like
WCD9335, WCD934x, WCD937x and WCD938x.
Most of the work is derived from downstream Qualcomm kernels.
Credits to various Qualcomm authors from Patrick Lai's team who have
contributed to this code.
Changes since v2:
- switched to EXPORT_SYMBOL_GPL from EXPORT_SYMBOL
- converted one of the if else to switch case.
Srinivas Kandagatla (4):
ASoC: dt-bindings: wcd934x: add bindings for Headset Button detection
ASoC: codecs: wcd: add multi button Headset detection support
ASoC: codecs: wcd934x: add mbhc support
ASoC: qcom: sdm845: add jack support for WCD934x
.../bindings/sound/qcom,wcd934x.yaml | 30 +
include/linux/mfd/wcd934x/registers.h | 57 +
sound/soc/codecs/Kconfig | 4 +
sound/soc/codecs/Makefile | 2 +
sound/soc/codecs/wcd-mbhc-v2.c | 1475 +++++++++++++++++
sound/soc/codecs/wcd-mbhc-v2.h | 340 ++++
sound/soc/codecs/wcd934x.c | 884 +++++++++-
sound/soc/qcom/sdm845.c | 8 +
8 files changed, 2785 insertions(+), 15 deletions(-)
create mode 100644 sound/soc/codecs/wcd-mbhc-v2.c
create mode 100644 sound/soc/codecs/wcd-mbhc-v2.h
--
2.21.0
WCD934x has Multi Button Headset Control hardware to support Headset insertion,
type detection, 8 headset buttons detection, Over Current detection and Impedence
measurements.
This patch adds support for this feature via common mbhc layer.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210604115230.23259-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Most new Qualcomm WCD codecs support MBHC(Multi Button Headset Control) via ADC.
This patchset adds support to Common parts of this MBHC support so that
WCD codecs need not duplicate them. To do that codec exposes set of
register fields and callbacks to this common driver to control it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210604115230.23259-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
With CONFIG_SND_SOC_LPASS_RX_MACRO=m and CONFIG_REGMAP_MMIO undefined,
build fails with the following error
make -f /var/tmp/portage/sys-kernel/stable-sources-5.12.8/work/linux-5.12.8-stable/scripts/Makefile.modpost
sed 's/\.ko$/\.o/' modules.order | scripts/mod/modpost -E -o modules-only.symvers -i vmlinux.symvers -T -
ERROR: modpost: "__devm_regmap_init_mmio_clk" [sound/soc/codecs/snd-soc-lpass-rx-macro.ko] undefined!
This does also apply to other Qualcomm Macro LPASS all making call to
devm_regmap_init_mmio()
Signed-off-by: Bertrand Jacquin <bertrand@jacquin.bzh>
Link: https://lore.kernel.org/r/20210603221816.2642402-1-bertrand@jacquin.bzh
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS2562_TDM_CFG0_SAMPRATE_MASK starts at bit 1, not 0.
So all values need to be left shifted by 1.
Signed-off-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20210530203446.19022-1-richard@nod.at
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow specifying Vddd regulator/supply to be enabled on I2C probing.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210528105101.508254-4-vincent.knecht@mailoo.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific init function to poke needed registers & values for this IC
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210528105101.508254-2-vincent.knecht@mailoo.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no reason why the arizona core,irq and codec model specific
regmap bits cannot be build as a module. All they do is export symbols
which are used by the arizona-spi/i2c and arizona-codec modules, which
themselves can be built as module.
Change the Kconfig and Makefile arizona bits so that the arizona MFD-core
can be built as a module.
This is especially useful on x86 platforms with a WM5102 codec, this
allows the arizona MFD driver necessary for the WM5102 codec to be
enabled in generic distro-kernels without growing the base kernel-image
size.
Note this also adds an explicit "depends on MFD_ARIZONA" to all the
arizona codec Kconfig options. The codec drivers use functions from mfd
arizona-core. These new depends are necessary to disallow the codec
drivers being builtin when the arizona-core is build as a module,
otherwise we end up with missing symbol errors when building vmlinuz.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The return value of snd_soc_component_write() is stored but not
evaluated and this results in a warning when W=1 is set. Stop storing
the return value to be consistent with all other calls of
snd_soc_component_write() and to remove the warning.
Fixes: 0d6a04da9b ("ASoC: Add Rockchip rk817 audio CODEC support")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The snd_compress_ops structs are only stored in the compress_ops field
of a snd_soc_component_driver struct, so make it const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210526231013.46530-4-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_compress_ops structs are only stored in the compress_ops field
of a snd_soc_component_driver struct, so make it const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210526231013.46530-3-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_compress_ops structs are only stored in the compress_ops field
of a snd_soc_component_driver struct, so make it const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210526231013.46530-2-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the Rockchip rk817 audio codec integrated into the
rk817 PMIC. This is based on the sources provided by Rockchip from
their BSP kernel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A slightly high volume at this time due to pending ASoC fixes.
While there are a few generic simple-card fixes for regressions,
most of the changes are device-specific fixes: ASoC Intel SOF, codec
clocks, other codec / platform fixes as well as usual HD-audio and
USB-audio.
-----BEGIN PGP SIGNATURE-----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=AIkz
-----END PGP SIGNATURE-----
Merge tag 'sound-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A slightly high volume at this time due to pending ASoC fixes.
While there are a few generic simple-card fixes for regressions, most
of the changes are device-specific fixes: ASoC Intel SOF, codec
clocks, other codec / platform fixes as well as usual HD-audio and
USB-audio"
* tag 'sound-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (37 commits)
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Zbook Fury 17 G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Zbook Fury 15 G8
ALSA: hda/realtek: fix mute/micmute LEDs and speaker for HP Zbook G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP 855 G8
ALSA: hda/realtek: Chain in pop reduction fixup for ThinkStation P340
ALSA: usb-audio: scarlett2: snd_scarlett_gen2_controls_create() can be static
ALSA: hda/realtek: the bass speaker can't output sound on Yoga 9i
ALSA: hda/realtek: Headphone volume is controlled by Front mixer
ALSA: usb-audio: scarlett2: Improve driver startup messages
ALSA: usb-audio: scarlett2: Fix device hang with ehci-pci
ALSA: usb-audio: fix control-request direction
ASoC: qcom: lpass-cpu: Use optional clk APIs
ASoC: cs35l33: fix an error code in probe()
ASoC: SOF: Intel: hda: don't send DAI_CONFIG IPC for older firmware
ASoC: fsl: fix SND_SOC_IMX_RPMSG dependency
ASoC: cs42l52: Minor tidy up of error paths
ASoC: cs35l32: Add missing regmap use_single config
ASoC: cs35l34: Add missing regmap use_single config
ASoC: cs42l73: Add missing regmap use_single config
ASoC: cs53l30: Add missing regmap use_single config
...
The power of "LDO2", "MICBIAS1" and "Mic Det Power" were powered off after
the DAPM widgets were added, and these powers were set by the JD settings
"RT5659_JD_HDA_HEADER" in the probe function. In the codec probe function,
these powers were ignored to prevent them controlled by DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Message-Id: <15fced51977b458798ca4eebf03dafb9@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use DEVICE_ATTR_WO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Message-Id: <20210524114239.7960-1-yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revise variable names and comments in
cs35l35 and cs35l36 amp drivers.
Signed-off-by: David Rhodes <drhodes@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-Id: <20210525194439.2232908-1-drhodes@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use DEVICE_ATTR_RO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Message-Id: <20210524114017.18672-1-yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use DEVICE_ATTR_WO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Message-Id: <20210524114753.39544-1-yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use DEVICE_ATTR_WO() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Message-Id: <20210524114503.26460-1-yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use DEVICE_ATTR_RW() helper instead of plain DEVICE_ATTR(),
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Message-Id: <20210524115131.46288-1-yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Jack must be connected before reporting button events and
if the jack is disconnected button release must be reported
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-4-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Add support for 2.4MHz clock source
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-3-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Add support for 24bits, 2 channels, 48k Sample rate bit clock
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-2-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
The 16 Bits, 2 channels, 48K sample rate use case needs
to configure a safer pll_divout during the start of PLL
After 800us from the start of PLL the correct pll_divout
can be set
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-Id: <20210525090822.64577-1-tanureal@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
A collection of fixes that have come in since the merge window, mainly
device specific things. The fixes to the generic cards from
Morimoto-san are handling regressions that were introduced in the merge
window on at least the Kontron sl28-var3-ads2.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmCraeoACgkQJNaLcl1U
h9BuVgf+Ith7351Fz+Jd1Y8e0rdVXuR4qVrkwm6u93/PRmFsL8DDWfURiHPuXJ+W
7NgsyreQEDLJYom8qloda/Lva2+FB0BHHkzUVLiZ7mDdbYq9Dush0QLLnOSP4p3O
GeeFJeK4EkeGHHFBbFllJ6gVB9xiokEcghXz1a+PkNMkYuQpAswlvhHxlIfEk1Bv
p1DBcM3gfT+3kfGynyz9A2O01zSd34Eg7tQuMqObxwFwpWY9mzrlYaPLdLF7Vtgc
JyQVvjTMaUZtiN/zGUFyXxAboTGWIFlPJKvHLHCiKvivSveXamziasieUwDU/cBL
X5SuIh883CghMhp8Dtx39zpcuiwEZQ==
=sQPM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.13-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.13
A collection of fixes that have come in since the merge window, mainly
device specific things. The fixes to the generic cards from
Morimoto-san are handling regressions that were introduced in the merge
window on at least the Kontron sl28-var3-ads2.
NXP's TFA98xx (now part of Goodix) are fairly popular speaker amplifiers
used in many smartphones and tablets. Most of them are sold as "smart
amplifiers" with built-in "CoolFlux DSP" that is used for volume control,
plus a "sophisticated speaker-boost and protection algorithm".
Unfortunately, they are also almost entirely undocumented. The short
datasheets (e.g. [1] for TFA9897) describe the available features,
but do not provide any information about the registers or how to use
the "CoolFlux DSP".
The amplifiers are most often configured through proprietary userspace
libraries. There are also some (rather complex) kernel drivers (e.g. [2])
but even those rely on obscure firmware blobs for configuration (so-called
"containers"). They seem to contain different "profiles" with tuned speaker
settings, sample rates and volume steps (which would be better exposed
as separate ALSA mixers).
The format of the firmware files seems to have changed a lot over the time,
so it's not even possible to simply re-use the firmware originally provided
by the vendor.
Overall, it seems close to impossible to develop a proper mainline driver
for these amplifiers that could make proper use of the built-in DSP.
This commit implements a compromise: At least the TFA1 family of the
TFA98xx amplifiers (usually called TFA989x) provide a way to *bypass*
the DSP using a special register sequence. The register sequence can be
found in similar variations in the kernel drivers from lots of vendors
e.g. in [3] and was probably mainly used for factory testing.
With the DSP bypassed, the amplifier acts mostly like a dumb standard
speaker amplifier, without (hardware) volume control. However, the setup
is much simpler and it works without any obscure firmware.
This driver implements the DSP bypass combined with chip-specific
initialization sequences adapted from [2]. Only TFA9895 is supported in
this initial commit. Except for the lack of volume control I can not hear
any difference with or without the DSP, it works just fine.
This driver allows the speaker to work on mainline Linux running on the
Samsung Galaxy A3/A5 (2015) [TFA9895] and Alcatel Idol 3 [TFA9897].
TFA9897 support will be added in separate patch set later.
[1]: https://product.goodix.com/en/docview/TFA9897%20SDS_Rev.3.1?objectId=47&objectType=document&version=78
[2]: https://source.codeaurora.org/external/mas/tfa98xx
[3]: 57b5050e34/sound/soc/codecs/tfa98xx.c (L1422-L1462)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210513104129.36583-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This error path returns zero (success) but it should return -EINVAL.
Fixes: 3333cb7187 ("ASoC: cs35l33: Initial commit of the cs35l33 CODEC driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/YKXuyGEzhPT35R3G@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from rk3328_platform_probe() in the error handling case.
Fixes: c32759035a ("ASoC: rockchip: support ACODEC for rk3328")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210518075847.1116983-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs43130_probe() does not do any valid error checking of things it
initializes, OR what it does, it does not unwind properly if there are
errors.
Fix this up by moving the sysfs files to an attribute group so the
driver core will correctly add/remove them all at once and handle errors
with them, and correctly check for creating a new workqueue and
unwinding if that fails.
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-58-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a2be42f18d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original patch here is not correct, sysfs files that were created
are not unwound.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-57-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for return value from various snd_soc_dapm_* calls, as many of
them can return errors and this should be handled. Also, reintroduce
the allocation failure check for rt5645->eq_param as well. Make all
areas where return values are checked lead to the end of the function
in the case of an error. Finally, introduce a comment explaining how
resources here are actually eventually cleaned up by the caller.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210503115736.2104747-56-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 51dd97d1df.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Lots of things seem to be still allocated here and must be properly
cleaned up if an error happens here.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-55-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Char pointer (cp) passed to tty_ldisc_ops::receive_buf{,2} is const.
There is no reason for flag pointer (fp) not to be too. So switch it in
the definition and all uses.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 312c004d36 ("[PATCH] driver core: replace "hotplug" by
"uevent"") already in the tree over a decade, update the name of
FW_ACTION defines to follow semantics, and reflect what the defines are
really meant for, i.e. whether or not generate user space event.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210425020024.28057-1-shawn.guo@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSBIAS_SENSE_EN configures HSBIAS output current sense through
the external 2.21-k resistor. HSBIAS_SENSE is hardware feature to reduce
the potential pop noise during the headset plug out slowly. But on some
platforms ESD voltage will affect it causing test to fail, especially
with CTIA headset type. For different hardware setups, a designer might
want to tweak default behavior.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511145220.125760-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We want all wm_adsp clients to use the wm_adsp.h header as they
shouldn't need to include internal sub-headers.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511171514.270219-1-simont@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The callback structures and memory region type table can be marked as
const as they will not change during use.
Fix checkpatch warning against wm_adsp_find_region function by moving
const keyword to form the 'static const struct' pattern.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511171459.270169-1-simont@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixup a needlessly initialised variable and an unchecked return
value.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511175718.15416-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This device requires single register transactions, this will
definely cause problems with the new device ID parsing which uses
regmap_bulk_read but might also show up in the cache sync sometimes.
Add the missing flags to the regmap_config.
Fixes: 283160f141 ("ASoC: cs35l32: Minor error paths fixups")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511175718.15416-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This device requires single register transactions, this will
definely cause problems with the new device ID parsing which uses
regmap_bulk_read but might also show up in the cache sync sometimes.
Add the missing flags to the regmap_config.
Fixes: 8cb9b00163 ("ASoC: cs35l34: Minor error paths fixups")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511175718.15416-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This device requires single register transactions, this will
definely cause problems with the new device ID parsing which uses
regmap_bulk_read but might also show up in the cache sync sometimes.
Add the missing flags to the regmap_config.
Fixes: 26495252fe ("ASoC: cs42l73: Minor error paths fixups")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511175718.15416-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This device requires single register transactions, this will
definely cause problems with the new device ID parsing which
uses regmap_bulk_read but might also show up in the cache sync
sometimes. Add the missing flags to the regmap_config.
Fixes: 4fc81bc88a ("ASoC: cs53l30: Minor error paths fixups")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511175718.15416-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620789145-14936-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs42l42 does not support standard burst transfers so the use_single_read
and use_single_write flags must be set in the regmap config.
Because of this bug, the patch:
commit 0a0eb567e1 ("ASoC: cs42l42: Minor error paths fixups")
broke cs42l42 probe() because without the use_single_* flags it causes
regmap to issue a burst read.
However, the missing use_single_* could cause problems anyway because the
regmap cache can attempt burst transfers if these flags are not set.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511132855.27159-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixup a needlessly initialised variable and an unchecked return
value.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511101051.17726-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixup a needlessly initialised variable and an unchecked return value.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210511101051.17726-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre requested I have a look at some cppcheck warnings in the cs42l42
driver, since it is reassigning the ret variable without ever checking
the result. Looking a bit more broadly this happens in quite a few
legacy Cirrus parts, as they all use the same process to read the ID,
factor out a small helper so they can all share the same code. Whilst
in there fix up a couple of other trivial error path issues as well.
Thanks,
Charles
Charles Keepax (10):
ASoC: cirrus: Add helper function for reading the device ID
ASoC: cs35l32: Minor error paths fixups
ASoC: cs35l33: Minor error paths fixups
ASoC: cs35l34: Minor error paths fixups
ASoC: cs35l35: Minor error paths fixups
ASoC: cs35l35: Correct errata handling
ASoC: cs42l42: Minor error paths fixups
ASoC: cs42l73: Minor error paths fixups
ASoC: cs43130: Minor error paths fixups
ASoC: cs53l30: Minor error paths fixups
sound/soc/codecs/cirrus_legacy.h | 21 +++++++++++++++++++++
sound/soc/codecs/cs35l32.c | 34 ++++++++++++++++++----------------
sound/soc/codecs/cs35l33.c | 15 +++++++++------
sound/soc/codecs/cs35l34.c | 39 ++++++++++++++++++++++-----------------
sound/soc/codecs/cs35l35.c | 21 ++++++++++-----------
sound/soc/codecs/cs35l35.h | 1 +
sound/soc/codecs/cs42l42.c | 18 ++++++++----------
sound/soc/codecs/cs42l73.c | 30 +++++++++++++++++-------------
sound/soc/codecs/cs43130.c | 31 +++++++++++++++++++------------
sound/soc/codecs/cs53l30.c | 22 +++++++++++-----------
10 files changed, 136 insertions(+), 96 deletions(-)
create mode 100644 sound/soc/codecs/cirrus_legacy.h
--
2.11.0
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-11-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-10-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-9-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-8-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the check of errata_chk will always evaluate to false since
the values tested don't come under the mask used. A shift of the field
is missing, add this. Also there is an error in the values tested, they
don't match the comment and the value 0x3 is not a valid value for the
field in question. Update the value to match the comment.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-7-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some unchecked re-allocations of ret whilst reading the device
ID and ensure the hardware state is returned to off on the error
paths.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Many of the older Cirrus devices share very similar code for reading the
device ID, and frequently this code is generating cppcheck warnings such
as:
sound/soc/codecs/cs42l42.c:1886:6: style: Variable 'ret' is reassigned
a value before the old one has been used. [redundantAssignment]
ret = regmap_read(cs42l42->regmap, CS42L42_DEVID_CD, ®);
Add a small helper function that older Cirrus devices can use to read
the device ID, which should help correct these issues.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210510131357.17170-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the device_property APIs so that the code will work on devicetree
and ACPI systems.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210426155303.853236-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the internal jack creation by set_jack call, so users can map
buttons in their machine driver
Also only enable jack detection IRQ after set_jack call
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210426155303.853236-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's implement a remove callback for this driver that's similar to the
shutdown hook, but also disables the regulators before they're put by
devm code.
Cc: Jairaj Arava <jairaj.arava@intel.com>
Cc: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: Shuming Fan <shumingf@realtek.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210508075151.1626903-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We cancel the work queues, and reset the device on shutdown, but the irq
isn't disabled so the work queues could be queued again. Let's disable
the irq during shutdown so that we don't have to worry about this device
trying to do anything anymore. This fixes a problem seen where the i2c
bus is shutdown at reboot but this device irq still comes in and tries
to make another i2c transaction when the bus doesn't work.
Cc: Jairaj Arava <jairaj.arava@intel.com>
Cc: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: Shuming Fan <shumingf@realtek.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Fixes: 45a2702ce1 ("ASoC: rt5682: Fix panic in rt5682_jack_detect_handler happening during system shutdown")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210508075151.1626903-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Static analysis reports this problem
lpass-wsa-macro.c:1732:6: warning: Array subscript is undefined
if (wsa->ec_hq[ec_tx]) {
^~~~~~~~~~~~~~~~~
The happens because 'ec_tx' is never initialized and there is
no default in switch statement that sets ec_tx. Add a default
case that returns an error before the array is accessed.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210430142117.3272772-1-trix@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable d_len_code is set to zero, but this value is never read as
it is overwritten or not used later on, hence it is a redundant
assignment and can be removed.
Clean up the following clang-analyzer warning:
sound/soc/codecs/rt286.c:728:2: warning: Value stored to 'd_len_code' is
never read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1620298735-31708-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following coccicheck warning:
./sound/soc/codecs/lpass-rx-macro.c:2631:2-3: Unneeded semicolon
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210506021005.4897-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/mt6359.c:274:8: style: Variable 'i' is assigned a
value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210426214701.235106-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning
sound/soc/codecs/mt6359-accdet.c:417:10: style: Variable 'ret' is
assigned a value that is never used. [unreadVariable]
int ret = 0;
^
sound/soc/codecs/mt6359-accdet.c:464:10: style: Variable 'ret' is
assigned a value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210426214701.235106-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210508031512.53783-1-cuibixuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function number should be FUNC_NUM_MIC_ARRAY(0x2) for the feature unit 0x1E.
Fixes: ca5118c0c0 ('ASoC: rt711-sdca: change capture switch controls')
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210504100424.8760-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No surprises in this development cycle, and most of works are about
the fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced;
used by HD-audio for now, more adaption will follow later.
The former "Mic Mute-LED Mode" mixer control has been replaced with
the corresponding sysfs now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements;
this will allow more controls in the normal usage pattern while
avoiding the possible memory exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates
Note that this PR includes a couple of changes in reset and SPI
drivers, too, and some merge conflicts might happen.
-----BEGIN PGP SIGNATURE-----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=YT3U
-----END PGP SIGNATURE-----
Merge tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No surprises in this development cycle, and most of work is about the
fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced. It is used by HD-audio
for now, more adaption will follow later. The former "Mic Mute-LED
Mode" mixer control has been replaced with the corresponding sysfs
now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements; this will allow more controls in
the normal usage pattern while avoiding the possible memory
exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates"
* tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (587 commits)
ALSA: hda/conexant: Re-order CX5066 quirk table entries
ALSA: hda/realtek: Remove redundant entry for ALC861 Haier/Uniwill devices
ALSA: hda/realtek: Re-order ALC662 quirk table entries
ALSA: hda/realtek: Re-order remaining ALC269 quirk table entries
ALSA: hda/realtek: Re-order ALC269 Lenovo quirk table entries
ALSA: hda/realtek: Re-order ALC269 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC269 ASUS quirk table entries
ALSA: hda/realtek: Re-order ALC269 Dell quirk table entries
ALSA: hda/realtek: Re-order ALC269 Acer quirk table entries
ALSA: hda/realtek: Re-order ALC269 HP quirk table entries
ALSA: hda/realtek: Re-order ALC882 Clevo quirk table entries
ALSA: hda/realtek: Re-order ALC882 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC882 Acer quirk table entries
ALSA: usb-audio: Remove redundant assignment to len
ALSA: hda/realtek: Add quirk for Intel Clevo PCx0Dx
ALSA: virtio: fix kernel-doc
ALSA: hda/cirrus: Use CS8409 filter to fix abnormal sounds on Bullseye
ALSA: hda/cirrus: Set Initial DMIC volume for Bullseye to -26 dB
ALSA: sb: Fix two use after free in snd_sb_qsound_build
ALSA: emu8000: Fix a use after free in snd_emu8000_create_mixer
...
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
This reverts commit 12f8127fe9.
There is problem with clk_hw_get_hw(). Using it pins the clock provider to
itself, making it impossible to remove the module.
Revert commit 12f8127fe9 ("ASoC: da7219: properly get clk from the
provider") until this gets sorted out.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210428122632.46244-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If
anyone shows up with this hardware, it is trivial to restore
these but we really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios
setting corner cases that loads of drivers got wrong as well
as removing unneeded code due to tty core changes from long
ago that were never propagated out to the drivers
- loads of platform-specific serial port driver updates and
fixes
- coding style cleanups and other small fixes and updates all
over the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa3NQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMXgCfX3FZgKveI4l94ChXSy4OyKwycHUAn00BzrMC
/7BwA1FnjQnC4zSzuHnm
=bAas
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If anyone
shows up with this hardware, it is trivial to restore these but we
really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios setting
corner cases that loads of drivers got wrong as well as removing
unneeded code due to tty core changes from long ago that were never
propagated out to the drivers
- loads of platform-specific serial port driver updates and fixes
- coding style cleanups and other small fixes and updates all over
the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
serial: extend compile-test coverage
serial: stm32: add FIFO threshold configuration
dt-bindings: serial: 8250: update TX FIFO trigger level
dt-bindings: serial: stm32: override FIFO threshold properties
dt-bindings: serial: add RX and TX FIFO properties
serial: xilinx_uartps: drop low-latency workaround
serial: vt8500: drop low-latency workaround
serial: timbuart: drop low-latency workaround
serial: sunsu: drop low-latency workaround
serial: sifive: drop low-latency workaround
serial: txx9: drop low-latency workaround
serial: sa1100: drop low-latency workaround
serial: rp2: drop low-latency workaround
serial: rda: drop low-latency workaround
serial: owl: drop low-latency workaround
serial: msm_serial: drop low-latency workaround
serial: mpc52xx_uart: drop low-latency workaround
serial: meson: drop low-latency workaround
serial: mcf: drop low-latency workaround
serial: lpc32xx_hs: drop low-latency workaround
...
This patch adds the return value when the volume settings were changed.
The userspace application might monitor the kcontrols to check which control changed.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210422103235.22048-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAPM event and mixer control could mute/unmute the capture directly.
That will be confused that capture still works if the user settings is unmute before the capture.
Therefore, this patch uses the variables to record the capture switch status of DAPM and mixer.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210422103220.21987-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using the clk embedded in the clk_hw (which is meant to go
away), a clock provider which need to interact with its own clock should
request clk reference through the clock provider API.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210421120512.413057-6-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Configuring number of channels per LRCLK frame by using e.g.
snd_soc_dai_set_tdm_slot before configuring DAI format was being
overwritten by the latter due to a regmap_write which would write over
the whole register.
Signed-off-by: Niklas Carlsson <niklasc@axis.com>
Link: https://lore.kernel.org/r/20210422130226.15201-1-Niklas.Carlsson@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable Daisy Chain if in TDM mode and the number of played
channels is bigger than the maximum supported number of channels.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1618915453-29445-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The last two patches in this series fix a longstanding issue that prevented
the ALC3263 codec from using a headset mic. This codec can be found on Dell
systems including the Latitude 13 7350, Venue 11 Pro 7140, and XPS 13 9343.
In fact, there is an ACPI quirk for the XPS 13 9343, which forces it to use
legacy HD Audio just to avoid this issue:
https://lore.kernel.org/alsa-devel/CAPeXnHv07HkvcHrYFmZMr8OTp7U7F=k_k=LPYnUtp89iPn2d2Q@mail.gmail.com/
This may allow that ACPI quirk to be removed. Either way, the other systems
mentioned above do not support this quirk and already use the ASoC driver,
so this fix is necessary for headset mic support on those systems.
Note: there is likely other handling for this codec that only exists in the
HDA driver, but which also belongs in the ASoC driver. Commit 394c97f824
("ALSA: hda/realtek - Change EAPD to verb control") describes an issue that
does not seem to be resolved in the ASoC driver, to give an example.
Other patches in this series are not specific to the ALC3263. These patches
set the correct combo jack configuration when headphones are inserted, and
fix a misaligned value set in the DMIC2 Configuration Default register.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=114171
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=150601
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205961
Signed-off-by: David Ward <david.ward@gatech.edu>
David Ward (5):
ASoC: rt286: Fix upper byte in DMIC2 configuration
ASoC: rt286: Configure combo jack for headphones
ASoC: rt298: Configure combo jack for headphones
ASoC: rt286: Make RT286_SET_GPIO_* readable and writable
ASoC: rt286: Generalize support for ALC3263 codec
sound/soc/codecs/rt286.c | 34 +++++++++++++++++++++-------------
sound/soc/codecs/rt298.c | 9 +++++++--
2 files changed, 28 insertions(+), 15 deletions(-)
--
2.31.1
The ALC3263 codec on the XPS 13 9343 is also found on the Latitude 13 7350
and Venue 11 Pro 7140. They require the same handling for the combo jack to
work with a headset: GPIO pin 6 must be set.
The HDA driver always sets this pin on the ALC3263, which it distinguishes
by the codec vendor/device ID 0x10ec0288 and PCI subsystem vendor ID 0x1028
(Dell). The ASoC driver does not use PCI, so adapt this check to use DMI to
determine if Dell is the system vendor.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=150601
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205961
Signed-off-by: David Ward <david.ward@gatech.edu>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210418134658.4333-6-david.ward@gatech.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
During jack detection, the combo jack is configured for a CTIA headset, and
then for an OMTP headset, while sensing the mic connection. If a mic is not
found in either case, the combo jack should be re-configured for headphones
only. This is consistent with the HDA driver behavior.
Signed-off-by: David Ward <david.ward@gatech.edu>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210418134658.4333-4-david.ward@gatech.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
During jack detection, the combo jack is configured for a CTIA headset, and
then for an OMTP headset, while sensing the mic connection. If a mic is not
found in either case, the combo jack should be re-configured for headphones
only. This is consistent with the HDA driver behavior.
Signed-off-by: David Ward <david.ward@gatech.edu>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210418134658.4333-3-david.ward@gatech.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALSA control readback functionality only works for non-volatile
controls, i.e. control values that does not change on their own without
driver interaction.
This doesn't work for readbacks since the DSP firmware updates the
control value. Disable the cache mechanism in the driver if the control
name matches the prefix used for readbacks to ensure that the control
value is valid.
Signed-off-by: Niklas Carlsson <niklasc@axis.com>
Link: https://lore.kernel.org/r/20210419144901.9441-1-Niklas.Carlsson@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The last two patches in this series fix a longstanding issue that prevented
the ALC3263 codec from using a headset mic. This codec can be found on Dell
systems including the Latitude 13 7350, Venue 11 Pro 7140, and XPS 13 9343.
In fact, there is an ACPI quirk for the XPS 13 9343, which forces it to use
legacy HD Audio just to avoid this issue:
https://lore.kernel.org/alsa-devel/CAPeXnHv07HkvcHrYFmZMr8OTp7U7F=k_k=LPYnUtp89iPn2d2Q@mail.gmail.com/
This may allow that ACPI quirk to be removed. Either way, the other systems
mentioned above do not support this quirk and already use the ASoC driver,
so this fix is necessary for headset mic support on those systems.
Note: there is likely other handling for this codec that only exists in the
HDA driver, but which also belongs in the ASoC driver. Commit 394c97f824
("ALSA: hda/realtek - Change EAPD to verb control") describes an issue that
does not seem to be resolved in the ASoC driver, to give an example.
Other patches in this series are not specific to the ALC3263. These patches
set the correct combo jack configuration when headphones are inserted, and
fix a misaligned value set in the DMIC2 Configuration Default register.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=114171
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=150601
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205961
Signed-off-by: David Ward <david.ward@gatech.edu>
David Ward (5):
ASoC: rt286: Fix upper byte in DMIC2 configuration
ASoC: rt286: Configure combo jack for headphones
ASoC: rt298: Configure combo jack for headphones
ASoC: rt286: Make RT286_SET_GPIO_* readable and writable
ASoC: rt286: Generalize support for ALC3263 codec
sound/soc/codecs/rt286.c | 34 +++++++++++++++++++++-------------
sound/soc/codecs/rt298.c | 9 +++++++--
2 files changed, 28 insertions(+), 15 deletions(-)
--
2.31.1
base-commit: a38fd87484
This HDA verb sets the upper byte of the Configuration Default register, so
only an 8-bit value should be used. For the rt298, the same fix was applied
in commit f8f2dc4a71 ("ASoC: rt298: fix wrong setting of gpio2_en").
Signed-off-by: David Ward <david.ward@gatech.edu>
Link: https://lore.kernel.org/r/20210418134658.4333-2-david.ward@gatech.edu
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5682.c:2404:42: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp << RT5682_PLL_M_BP_SFT | RT5682_PLL_RST));
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210416191144.27006-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/lpass-rx-macro.c:1626:9: warning: Identical condition
and return expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/lpass-rx-macro.c:1623:6: note: If condition 'ret' is
true, the function will return/exit
if (ret)
^
sound/soc/codecs/lpass-rx-macro.c:1626:9: note: Returning identical
expression 'ret'
return ret;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210416191144.27006-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add main capture switch and main capture volume control.
Main capture control has its own channel value respectivelly.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/dfd43a8db04e4d52a889d6f5c1262173@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=7O9a
-----END PGP SIGNATURE-----
mergetag object a908a71669
type commit
tag ib-mfd-extcon-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616067995 +0000
Immutable branch between MFD and Extcon due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=3CZN
-----END PGP SIGNATURE-----
mergetag object eac013a0b7
type commit
tag ib-mfd-input-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374673 +0000
Immutable branch between MFD and Input due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=NF6J
-----END PGP SIGNATURE-----
mergetag object aa47ad3f85
type commit
tag ib-mfd-platform-x86-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1615373744 +0000
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=340a
-----END PGP SIGNATURE-----
mergetag object ee0975c308
type commit
tag ib-mfd-power-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616489771 +0000
Immutable branch between MFD and Power due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
mergetag object edbda8f787
type commit
tag ib-mfd-pwm-rtc-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374433 +0000
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=DySP
-----END PGP SIGNATURE-----
Merge tags 'ib-mfd-clk-gpio-regulator-rtc-v5.13', 'ib-mfd-extcon-v5.13', 'ib-mfd-input-v5.13-1', 'ib-mfd-platform-x86-v5.13', 'ib-mfd-power-v5.13', 'ib-mfd-pwm-rtc-v5.13-1' and 'ib-regulator-list-ramp-helpers-v5.13' into ibs-for-mfd-merged
Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window
Immutable branch between MFD and Extcon due for the v5.13 merge window
Immutable branch between MFD and Input due for the v5.13 merge window
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
Immutable branch between MFD and Power due for the v5.13 merge window
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062644.802988-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062657.803668-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062642.802846-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062647.803141-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062648.803227-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062654.803538-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062650.803309-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062646.803053-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062656.803606-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062701.803865-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062643.802908-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In DT binding is mentioned that this driver is compatible with 3106.
So added compatibility string and model number.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Link: https://lore.kernel.org/r/20210408135908.125667-1-jiri.prchal@aksignal.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062700.803792-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a rumtime PM imbalance between the error handling path
after devm_snd_soc_register_component() and all other error
handling paths. Add a PM runtime increment to balance refcount.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210408064036.6691-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
For latest design, different package could use the same setting,
therefore the check of pack_id will no longer be used.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/4cbe1cd3b8664140889132464c7dee7b@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210407074218.3051979-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock registration must be performed before the component is
registered. aic32x4_component_probe attempts to get all the
clocks right off the bat. If the component is registered before
the clocks there is a race condition where the clocks may not
be registered by the time aic32x4_componet_probe actually runs.
Fixes: d1c859d314 ("ASoC: codec: tlv3204: Increased maximum supported channels")
Cc: stable@vger.kernel.org
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Link: https://lore.kernel.org/r/0101017889850206-dcac4cce-8cc8-4a21-80e9-4e4bef44b981-000000@us-west-2.amazonses.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5670 codec driver uses DMI quirks to configure the DMIC data-pins,
which means that it knows which DMIC interface is used on a specific
device.
ATM we duplicate this DMI matching inside the UCM profiles to select
the right DMIC interface. Add a rt5670_components() helper which the
machine-driver can use to set the components string of the card so
that UCM can get the info from the components string.
This way we only need to add new DMI quirks in one place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210402140747.174716-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk with the jack-detect and dmic settings necessary to make
jack-detect and the builtin mic work on Dell Venue 10 Pro 5055 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210402140747.174716-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
NPL clock rate is twice the MCLK rate, so set this correctly to
avoid soundwire timeouts.
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210331171235.24824-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
NPL clock rate is twice the MCLK rate, so set this correctly to
avoid soundwire timeouts.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210331171235.24824-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck reports a false positive:
sound/soc/codecs/da732x.c:1161:25: warning: Either the condition
'indiv<0' is redundant or there is division by zero at line
1161. [zerodivcond]
fref = (da732x->sysclk / indiv);
^
sound/soc/codecs/da732x.c:1158:12: note: Assuming that condition
'indiv<0' is not redundant
if (indiv < 0)
^
sound/soc/codecs/da732x.c:1161:25: note: Division by zero
fref = (da732x->sysclk / indiv);
^
The code is awfully convoluted/confusing and can be simplified with a
single variable and the BIT macro.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210326221619.949961-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck warning:
sound/soc/codecs/lm49453.c:1210:11: style: Variable 'pll_clk' is
assigned a value that is never used. [unreadVariable]
pll_clk = BIT(4);
^
FIXME: What is the correct fix?
/* fll clk slection */
pll_clk = BIT(4);
return 0;
is the assignment redundant or the 'return 0' a mistake?
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210326221619.949961-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=1uM7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmBkoFEACgkQJNaLcl1U
h9BqTgf5AUfR5NbQgJIUMtdMsuz+bthKGuPnpYhYzNUH0io9i3Sjpt0Mbw21dLp2
nXW+70BH0tJZBGR4DNGpmcpBLH5WPdOR9WIv4vCYy9Pr0uCGGKF/JkGeZAg7/llF
C3+yDfTnF0AvR+74xbf/LTjBPGja/08PED1ZC00NAkLhE3C0Pa/VQ0NaEtPUULWE
ZOWboF7hfQUeGzGPTqNp4Cy0/Pzokk6Fvl4kgfrxjNWO7ojIv9mCAvmYbusLW7NU
3Ph5VGsIuyMeorEoAVOFaBY2nrYG/mFZyzTNWJMgvF1MdeigMPNfbbffrUK0sn6k
e81zgWbwxboEujQ91/EZU7glIqtb6A==
=rr4V
-----END PGP SIGNATURE-----
Merge tag 'mute-led-rework' of https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-5.13
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
0x20FF(amp global enable) register was defined as non-volatile,
but it is not. Overheating, overcurrent can cause amp shutdown
in hardware.
'regmap_write' compare register readback value before writing
to avoid same value writing. 'regmap_read' just read cache
not actual hardware value for the non-volatile register.
When amp is internally shutdown by some reason, next 'AMP ON'
command can be ignored because regmap think amp is already ON.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20210325033555.29377-1-ryans.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The call sequence in wm8960_configure_clocking is
ret = wm8960_configure_sysclk();
if (ret >= 0)
goto configure_clock;
....
ret = wm8960_configure_pll();
configure_clock:
...
wm8960_configure_sysclk is called before wm8960_configure_pll, as
there is bitclk relax on both functions, so wm8960_configure_sysclk
always return success, then wm8960_configure_pll() never be called.
With this case:
aplay -Dhw:0,0 -d 5 -r 48000 -f S24_LE -c 2 audio48k24b2c.wav
the required bitclk is 48000 * 24 * 2 = 2304000, bitclk got from
wm8960_configure_sysclk is 3072000, but if go to wm8960_configure_pll.
it can get correct bitclk 2304000.
So bitclk relax condition should be removed in wm8960_configure_sysclk,
then wm8960_configure_pll can be called, and there is also bitclk relax
function in wm8960_configure_pll.
Fixes: 3c01b9ee2a ("ASoC: codec: wm8960: Relax bit clock computation")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1614740862-30196-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
3 new controls are added.
"OVC Autorestart Switch" : controls whether or not the speaker amplifier
automatically re-enables after an overcurrent fault condition.
"THERM Autorestart Switch" : controls whether or not the device
automatically resumes playback when the die temperature recovers from
thermal shutdown.
"CMON Autorestart Switch" : controls whether or not the device
automatically resumes playback when the clock returns after stopping.
Above Auto Restart functions are enabled by default.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20210325033555.29377-3-ryans.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make all arizona codec drivers for which drivers/mfd/arizona-core.c used
to instantiate a "arizona-extcon" child-device use the new arizona-jack.c
library for jack-detection.
This has been tested on a Lenovo Yoga Tablet 2 1051L with a WM5102 codec.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-13-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup the use of dev_foo functions used for logging:
1. Many of these are unnecessarily split over multiple lines
2. Use dev_err_probe() in cases where we might get a -EPROBE_DEFER
return value
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-12-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the snd_soc_jack code to report jack events, instead of using extcon
for reporting the cable-type + an input_dev for reporting the button
presses.
The snd_soc_jack code will report the cable-type through both input_dev
events and through ALSA controls and the button-presses through input_dev
events.
Note that this means that when the codec drivers are moved over to use
the new arizona-jack.c library code instead of having a separate MFD
extcon cell with the extcon-arizona.c driver, we will no longer report
extcon events to userspace for cable-type changes. This should not be
a problem since "standard" Linux distro userspace does not (and has
never) used the extcon class interface for this. Android does have
support for the extcon class interface, but that was introduced in
the same release as support for input_dev cable-type events, so this
should not be a problem for Android either.
Note this also reduces ARIZONA_MAX_MICD_RANGE from 8 to 6, this is
ok to do since this info is always provided through pdata (or defaults)
and cannot be overridden from devicetree. All in-kernel users of the
pdata (and the fallback defaults) define 6 or less buttons/ranges.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-11-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the arizona extcon driver into a helper library for direct use
from the arizona codec-drivers, rather then being bound to a separate
MFD cell.
Note the probe (and remove) sequence is split into 2 parts:
1. The arizona_jack_codec_dev_probe() function inits a bunch of
jack-detect specific variables in struct arizona_priv and tries to get
a number of resources where getting them may fail with -EPROBE_DEFER.
2. Then once the machine driver has create a snd_sock_jack through
snd_soc_card_jack_new() it calls snd_soc_component_set_jack() on
the codec component, which will call the new arizona_jack_set_jack(),
which sets up jack-detection and requests the IRQs.
This split is necessary, because the IRQ handlers need access to the
arizona->dapm pointer and the snd_sock_jack which are not available
when the codec-driver's probe function runs.
Note this requires that machine-drivers for codecs which are converted
to use the new helper functions from arizona-jack.c are modified to
create a snd_soc_jack through snd_soc_card_jack_new() and register
this jack with the codec through snd_soc_component_set_jack().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-10-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers for MFD child-devices such as the arizona codec drivers
and the arizona-extcon driver can choose to either make
runtime_pm_get/_put calls on their own child-device, which will
then be propagated to their parent; or they can make them directly
on their MFD parent-device.
The arizona-extcon code was using runtime_pm_get/_put calls on
its own child-device where as the codec drivers are using
runtime_pm_get/_put calls on their parent.
The arizona-extcon MFD cell/child-device has been removed and this
commit is part of refactoring the arizona-extcon code into a library
to be used directly from the codec drivers.
Specifically this commit moves the code over to make
runtime_pm_get/_put calls on the parent device (on arizona->dev)
bringing the code inline with how the codec drivers do this.
Note this also removes the pm_runtime_enable/_disable calls
as pm_runtime support has already been enabled on the parent-device
by the arizona MFD driver.
This is part of a patch series converting the arizona extcon driver into
a helper library for letting the arizona codec-drivers directly report
jack state through the standard sound/soc/soc-jack.c functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-9-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all the jack-detect variables from struct arizona_extcon_info to
struct arizona_priv.
This is part of a patch series converting the arizona extcon driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-8-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sparse tool complains as follows:
sound/soc/codecs/rt1019.c:927:19: warning:
symbol 'rt1019_i2c_driver' was not declared. Should it be static?
This symbol is not used outside of rt1019.c, so this
commit marks it static.
Fixes: 7ec79d3850 ("ASoC: rt1019: add rt1019 amplifier driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210319094102.4185096-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/tscs454.c:730:37: style: Same value in both branches
of ternary operator. [duplicateValueTernary]
val = pll1 ? FV_PLL1CLKEN_DISABLE : FV_PLL2CLKEN_DISABLE;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-24-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/tas2770.c:109:10: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-22-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/tas2562.c:530:9: warning: Identical condition and return expression 'ret', return value is always 0 [identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/tas2562.c:525:6: note: If condition 'ret' is true, the function will return/exit
if (ret)
^
sound/soc/codecs/tas2562.c:530:9: note: Returning identical expression 'ret'
return ret;
^
Fix with return 0
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-21-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck throws a warning:
sound/soc/codecs/tas2562.c:203:4: style: Assignment of function
parameter has no effect outside the function. [uselessAssignmentArg]
tx_mask &= ~(1 << right_slot);
^
This assignment seems to come from a copy/paste but the value is
indeed not used. Let's remove it.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-20-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/sti-sas.c:54:25: style: struct member
'sti_dac_audio::field' is never used. [unusedStructMember]
struct regmap_field **field;
^
sound/soc/codecs/sti-sas.c:55:24: style: struct member
'sti_dac_audio::rst' is never used. [unusedStructMember]
struct reset_control *rst;
^
sound/soc/codecs/sti-sas.c:61:25: style: struct member
'sti_spdif_audio::field' is never used. [unusedStructMember]
struct regmap_field **field;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/pcm1681.c:87:8: style: Variable 'i' is assigned a
value that is never used. [unreadVariable]
int i = 0, val = -1, enable = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/nau8825.c:2113:10: style: Variable 'ret' is assigned
a value that is never used. [unreadVariable]
int ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/mt6359.c:242:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:260:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:8: style: Variable 'i' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:19: style: Variable 'stage' is assigned a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/mt6358.c:334:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6358.c:350:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
185/930 files checked 25% done
Checking sound/soc/codecs/mt6359.c ...
sound/soc/codecs/mt6359.c:274:8: style: Variable 'i' is assigned a
value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
sound/soc/codecs/mt6359.c:274:19: style: Variable 'stage' is assigned
a value that is never used. [unreadVariable]
int i = 0, stage = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/max98090.c:1835:16: style: Variable 'test_diff' is
assigned a value that is never used. [unreadVariable]
int test_diff = INT_MAX;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
fix cppcheck warning:
sound/soc/codecs/hdmi-codec.c:25:16: style: struct member
'hdmi_codec_channel_map_table::spk_mask' is never
used. [unusedStructMember]
unsigned long spk_mask; /* speaker position bit mask */
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix cppcheck warning:
sound/soc/codecs/hdmi-codec.c:745:5: style: Redundant initialization
for 'cf'. The initialized value is overwritten before it is
read. [redundantInitialization]
cf = dai->playback_dma_data;
^
sound/soc/codecs/hdmi-codec.c:738:31: note: cf is initialized
struct hdmi_codec_daifmt *cf = dai->playback_dma_data;
^
sound/soc/codecs/hdmi-codec.c:745:5: note: cf is overwritten
cf = dai->playback_dma_data;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck complains a lot about possible null pointer dereferences but
it's again a case of useless initializations to NULL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/da7219-aad.c:118:22: style: Variable 'ret' is
assigned a value that is never used. [unreadVariable]
int report = 0, ret = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210312182246.5153-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/cx2072x.c:1436:10: style:inconclusive: Found
duplicate branches for 'if' and 'else'. [duplicateBranch]
} else if (type & 0x4) {
^
sound/soc/codecs/cx2072x.c:1439:5: note: Found duplicate branches for
'if' and 'else'.
} else {
^
sound/soc/codecs/cx2072x.c:1436:10: note: Found duplicate branches for
'if' and 'else'.
} else if (type & 0x4) {
^
The last two branches do the same thing and can be collapsed together.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210312182246.5153-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck warning:
sound/soc/codecs/cx2072x.c:830:26: style: Variable
'reg1.r.rx_data_one_line' is reassigned a value before the old one has
been used. [redundantAssignment]
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:782:26: note: reg1.r.rx_data_one_line is
assigned
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:830:26: note: reg1.r.rx_data_one_line is
overwritten
reg1.r.rx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:831:26: style: Variable
'reg1.r.tx_data_one_line' is reassigned a value before the old one has
been used. [redundantAssignment]
reg1.r.tx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:783:26: note: reg1.r.tx_data_one_line is
assigned
reg1.r.tx_data_one_line = 1;
^
sound/soc/codecs/cx2072x.c:831:26: note: reg1.r.tx_data_one_line is
overwritten
reg1.r.tx_data_one_line = 1;
^
Likely copy/paste.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210312182246.5153-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck complains of a possible issue:
sound/soc/codecs/cros_ec_codec.c:98:10: warning: Possible null pointer
dereference: in [nullPointer]
memcpy(in, msg->data, insize);
^
sound/soc/codecs/cros_ec_codec.c:162:34: note: Calling function
'send_ec_host_command', 5th argument 'NULL' value is 0
(uint8_t *)&p, sizeof(p), NULL, 0);
^
sound/soc/codecs/cros_ec_codec.c:98:10: note: Null pointer dereference
memcpy(in, msg->data, insize);
^
In practice the access to the pointer is protected by another
argument, but this is likely to fool other static analysis tools. Add
a test to avoid doing the memcpy if the pointer is NULL or the size is
zero.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210312182246.5153-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck warning:
sound/soc/codecs/adau1977.c:242:9: warning: Identical condition and
return expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/adau1977.c:239:6: note: If condition 'ret' is true,
the function will return/exit
if (ret)
^
sound/soc/codecs/adau1977.c:242:9: note: Returning identical expression 'ret'
return ret;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck warning:
sound/soc/codecs/ad1836.c:311:9: warning: Identical condition and return expression 'ret', return value is always 0 [identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/ad1836.c:308:6: note: If condition 'ret' is true, the function will return/exit
if (ret)
^
sound/soc/codecs/ad1836.c:311:9: note: Returning identical expression 'ret'
return ret;
^
Likely copy/paste between adc and dac cases.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cppcheck warnings:
sound/soc/codecs/ab8500-codec.c:117:20: style: struct member 'ab8500_codec_drvdata_dbg::vaud' is never used. [unusedStructMember]
struct regulator *vaud;
^
sound/soc/codecs/ab8500-codec.c:118:20: style: struct member 'ab8500_codec_drvdata_dbg::vamic1' is never used. [unusedStructMember]
struct regulator *vamic1;
^
sound/soc/codecs/ab8500-codec.c:119:20: style: struct member 'ab8500_codec_drvdata_dbg::vamic2' is never used. [unusedStructMember]
struct regulator *vamic2;
^
sound/soc/codecs/ab8500-codec.c:120:20: style: struct member 'ab8500_codec_drvdata_dbg::vdmic' is never used. [unusedStructMember]
struct regulator *vdmic;
^
The structure is never used, remove.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312182246.5153-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With commit 1e30f642cf ("ASoC: simple-card-utils: Fix device module clock")
simple-card-utils can control MCLK clock for rate updates or enable/disable.
But this is breaking some platforms where it is expected that codec drivers
would actually handle the MCLK clock. One such example is following platform.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
In above case codec, wm8904, is using internal PLL and configures sysclk
based on fixed MCLK input. In such cases it is expected that, required PLL
output or sysclk, is just passed via set_sysclk() callback and card driver
need not actually update MCLK rate. Instead, codec can take ownership of
this clock and do the necessary configuration.
So the original commit is reverted and codec driver for rt5659 is updated
to fix my board which has this codec.
Sameer Pujar (2):
ASoC: simple-card-utils: Do not handle device clock
ASoC: rt5659: Update MCLK rate in set_sysclk()
sound/soc/codecs/rt5659.c | 5 +++++
sound/soc/generic/simple-card-utils.c | 13 +++++++------
2 files changed, 12 insertions(+), 6 deletions(-)
--
2.7.4
We do some IO operations in the snd_soc_component_set_jack callback
function and snd_soc_component_set_jack() will be called when soc
component is removed. However, we should not access SoundWire registers
when the bus is suspended.
So set regcache_cache_only(regmap, true) to avoid accessing in the
soc component removal process.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210316005254.29699-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1615829492-8972-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename 'Mono DAC Playback Volume' to 'DAC2 Playback Volume' and move it
from rt5640_specific_snd_controls[] to rt5640_snd_controls[].
The RT5640_DAC2_DIG_VOL register controlled by this mixer-element has
nothing to do with the Mono (Amplified) output which is only available
on the ALC5640 chip and not on the ALC5642 chip.
The RT5640_DAC2_DIG_VOL volume-control is the main volume control for
audio coming from the I2S2 / AIF2 input of the chip and as such is also
available on the ALC5642.
This commit results in the following userspace visible changes:
1. On devices with an ACL5640 codec, the 'Mono DAC Playback Volume'
control is renamed to 'DAC2 Playback Volume' allowing the alsa-lib
mixer code to properly group it with the 'DAC2 Playback Switch' which
is controlling the mute bits in the RT5640_DAC2_DIG_VOL register.
Note the removal of the 'Mono DAC Playback Volume' is not an issue for
userspace because the UCM profiles do not use it (the UCM profiles are
shared betweent the 5640 and 5642 and only the 5640 had this control).
2. On devices with an ACL5642 codec, there now will be a new
'DAC2 Playback Volume', grouped with the 'DAC2 Playback Switch'
Having a complete 'DAC2 Playback Volume' / 'DAC2 Playback Switch' pair
on both variants will allow enabling hardware-volume control by
setting the UCM PlaybackMasterElem to "DAC2" on devices where the
I2S2/AIF2 interface of the codec is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307150503.34906-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/wm_adsp.c:2092:9: warning: Identical condition and
return expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/codecs/wm_adsp.c:2070:6: note: If condition 'ret' is true,
the function will return/exit
if (ret)
^
sound/soc/codecs/wm_adsp.c:2092:9: note: Returning identical
expression 'ret'
return ret;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/wm8903.c:1552:11: style: Variable 'best_val' is
assigned a value that is never used. [unreadVariable]
best_val = ((clk_sys * 10) / bclk_divs[0].ratio) - bclk;
^
sound/soc/codecs/wm8903.c:1559:12: style: Variable 'best_val' is
assigned a value that is never used. [unreadVariable]
best_val = cur_val;
^
Indeed what matters in the code is the blck_div, the best_val is
assigned but never tested or used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck complains about some members not being used, but it's really
the entire structure that is never used anywhere.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210311004332.120901-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi All,
Here is a patch series for reporting to user space jack and button events and
add the support for Capture. With some cleanups and fixes along the way.
Regards,
Lucas Tanure
Lucas Tanure (12):
ASoC: cs42l42: Fix Bitclock polarity inversion
ASoC: cs42l42: Fix channel width support
ASoC: cs42l42: Fix mixer volume control
ASoC: cs42l42: Don't enable/disable regulator at Bias Level
ASoC: cs42l42: Always wait at least 3ms after reset
ASoC: cs42l42: Remove power if the driver is being removed
ASoC: cs42l42: Disable regulators if probe fails
ASoC: cs42l42: Provide finer control on playback path
ASoC: cs42l42: Set clock source for both ways of stream
ASoC: cs42l42: Add Capture Support
ASoC: cs42l42: Report jack and button detection
ASoC: cs42l42: Use bclk from hw_params if set_sysclk was not called
Richard Fitzgerald (3):
ASoC: cs42l42: Wait at least 150us after writing SCLK_PRESENT
ASoC: cs42l42: Only start PLL if it is needed
ASoC: cs42l42: Wait for PLL to lock before switching to it
sound/soc/codecs/cs42l42.c | 435 +++++++++++++++++++++----------------
sound/soc/codecs/cs42l42.h | 41 +++-
2 files changed, 282 insertions(+), 194 deletions(-)
--
2.30.1
This patch keeps the delay time (50 ms) for jack detection and zero delay time for the button press.
This patch improves the reaction of the button press.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210309085827.32032-1-shumingf@realtek.com
Tested-by Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function devm_regmap_init_sdw_mbq() and
devm_regmap_init_sdw() returns ERR_PTR() not NULL. The NULL test
in the return value check should be replaced with IS_ERR().
Fixes: 393c52d2d109 ("ASoC: rt715-sdca: Add RT715 sdca vendor-specific driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210309131458.1884899-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL is only needed for sclk < 11289600 Hz and cs42l42_pll_config()
will not configure it for higher rates. So it must only be enabled
when it is needed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-15-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There must be a delay of at least 150us after writing SCLK_PRESENT
before issuing another I2C write.
This is done using struct reg_sequence because it can specify a delay
after the write and the whole sequence is written atomically.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-14-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for reading the source clock from snd_soc_params_to_bclk
so the machine driver is not required to call cs42l42_set_sysclk
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-13-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report the Jack events to the user space through ALSA.
Also moves request_threaded_irq() to component_probe so it don't get
interrupts before the initialization the struct snd_soc_jack.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210306185553.62053-12-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Asus T100HA and T101HA 2-in-1s use a rt5645 family codec and always
report that a headset (rather then headphones) are plugged in even when
regular headphones are plugged in.
And when a headset is used, then the headset-microphone does not work.
According to RealTek the ALC3270 variant used in these devices does not
support headsets only headphones.
Since the ALC3270 is a budget version of the regular ALC5645 codec,
I assume that it is using a package with less pins and the headset-mic
pin is simply not connected.
Detect if the codec is an ALC3270 based on the ACPI HID and if it is
an ALC3270 then always report SND_JACK_MICROPHONE as false, so that
userspace will not try to use the not-connected headset-mic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210306230223.516566-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/rt5645.c is the only user of the rt5645_platform_data,
move its definition to sound/soc/codecs/rt5645.c and remove the now
empty include/sound/rt5645.h file.
Note since the DMI quirk mechanism uses pointers to the
rt5645_platform_data struct we can NOT simply add its members to
the rt5645_priv struct and completely remove the struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210306230223.516566-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function devm_platform_ioremap_resource has already contained
error message if failed, so remove superfluous dev_err here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210307072133.10832-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With S20_3LE format case, the sysclk = rate * 384,
the bclk = rate * 20 * 2, there is no proper bclk divider
for 384 / 40, because current condition needs exact match.
So driver fails to configure the clocking:
wm8962 3-001a: Unsupported BCLK ratio 9
Fix this by relaxing bitclk divider searching, so that when
no exact value can be derived from sysclk pick the closest
value greater than expected bitclk.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1615170877-25918-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
./sound/soc/codecs/lpass-rx-macro.c:3588:3-8: No need to set .owner here.
The core will do it.
Remove .owner field if calls are used which set it automatically
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1614762481-102466-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of error, the function devm_regmap_init_sdw() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: a262057df513 ("ASoC: rt1316: Add RT1316 SDCA vendor-specific driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210303064041.898281-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function devm_platform_ioremap_resource has already contained
error message, so remove the redundant dev_err here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210302135630.11456-1-tangbin@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make W=1 warning:
sound/soc/codecs/sigmadsp-regmap.c:42: warning: expecting prototype
for devm_sigmadsp_init_i2c(). Prototype was for
devm_sigmadsp_init_regmap() instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302205926.49063-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make W=1 warning:
sound/soc/codecs/rt5631.c:446: warning: expecting prototype for
onebit_depop_power_stage(). Prototype was for depop_seq_power_stage()
instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302205926.49063-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make W=1 warning:
sound/soc/codecs/jz4760.c: In function ‘jz4760_codec_startup’:
sound/soc/codecs/jz4760.c:201:6: error: variable ‘ret’ set but not
used [-Werror=unused-but-set-variable]
201 | int ret;
| ^~~
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302205926.49063-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck complains about a possible null pointer dereference, but the
problem is rather an useless initialization before walking through a
list.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-25-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/rt5682.c🔢6: style: Redundant initialization for
'idx'. The initialized value is overwritten before it is
read. [redundantInitialization]
idx = rt5682_div_sel(rt5682, dmic_clk_rate, div, ARRAY_SIZE(div));
^
sound/soc/codecs/rt5682.c:1228:10: note: idx is initialized
int idx = -EINVAL, dmic_clk_rate = 3072000;
^
sound/soc/codecs/rt5682.c🔢6: note: idx is overwritten
idx = rt5682_div_sel(rt5682, dmic_clk_rate, div, ARRAY_SIZE(div));
^
sound/soc/codecs/rt5682.c:1263:6: style: Redundant initialization for
'idx'. The initialized value is overwritten before it is
read. [redundantInitialization]
idx = rt5682_div_sel(rt5682, ref, div_f, ARRAY_SIZE(div_f));
^
sound/soc/codecs/rt5682.c:1248:25: note: idx is initialized
int ref, val, reg, idx = -EINVAL;
^
sound/soc/codecs/rt5682.c:1263:6: note: idx is overwritten
idx = rt5682_div_sel(rt5682, ref, div_f, ARRAY_SIZE(div_f));
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-24-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5682.c:2401:65: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5682_PLL_M_SFT |
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-23-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5677.c:5335:10: style: Variable 'ret' is assigned a
value that is never used. [unreadVariable]
int ret = 0, loop, i, reg_irq, virq;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-22-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5677.c:4571:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5677_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-21-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5670.c:2519:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5670_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-20-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warnings:
sound/soc/codecs/rt5668.c:1177:6: style: Redundant initialization for
'idx'. The initialized value is overwritten before it is
read. [redundantInitialization]
idx = rt5668_div_sel(rt5668, 1500000, div, ARRAY_SIZE(div));
^
sound/soc/codecs/rt5668.c:1174:10: note: idx is initialized
int idx = -EINVAL;
^
sound/soc/codecs/rt5668.c:1177:6: note: idx is overwritten
idx = rt5668_div_sel(rt5668, 1500000, div, ARRAY_SIZE(div));
^
sound/soc/codecs/rt5668.c:1202:6: style: Redundant initialization for
'idx'. The initialized value is overwritten before it is
read. [redundantInitialization]
idx = rt5668_div_sel(rt5668, ref, div, ARRAY_SIZE(div));
^
sound/soc/codecs/rt5668.c:1191:25: note: idx is initialized
int ref, val, reg, idx = -EINVAL;
^
sound/soc/codecs/rt5668.c:1202:6: note: idx is overwritten
idx = rt5668_div_sel(rt5668, ref, div, ARRAY_SIZE(div));
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5668.c:2185:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5668_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5665.c:4388:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5665_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5663_PLL_M_SHIFT |
^
sound/soc/codecs/rt5663.c:2955:63: style: Boolean result is used in
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5660.c:1060:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5660_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5659.c:3515:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5659_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5651.c:1786:13: style: Variable 'report' is
assigned a value that is never used. [unreadVariable]
int report = 0;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5659.c:3515:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5659_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5645.c:2959:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5645_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5645.c:693:37: style:inconclusive: Boolean
expression 'reg>=420&®<=461' is used in bitwise operation. Did you
mean '||'? [bitwiseOnBoolean]
if ((reg >= 0x1a4 && reg <= 0x1cd) | (reg >= 0x1e5 && reg <= 0x1f8) |
^
sound/soc/codecs/rt5645.c:693:70: style:inconclusive: Boolean
expression 'reg==177' is used in bitwise operation. Did you mean '||'?
[bitwiseOnBoolean]
if ((reg >= 0x1a4 && reg <= 0x1cd) | (reg >= 0x1e5 && reg <= 0x1f8) |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt5640.c:1923:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT5640_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1308.c:676:40: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
pll_code.k_code << RT1308_PLL1_K_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1305.c:853:63: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT1305_PLL_1_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1016.c:503:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT1016_PLL_M_SFT |
^
sound/soc/codecs/rt1016.c:506:40: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
pll_code.k_bp << RT1016_PLL_K_BP_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1015.c:894:61: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT1015_PLL_M_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1011.c:1781:63: style: Boolean result is used in
bitwise operation. Clarify expression with
parentheses. [clarifyCondition]
(pll_code.m_bp ? 0 : pll_code.m_code) << RT1011_PLL1_QM_SFT |
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/codecs/rt1011.c:1994:6: style: Condition 'tx_slotnum' is
always true [knownConditionTrueFalse]
if (tx_slotnum)
^
sound/soc/codecs/rt1011.c:1895:24: note: Assuming that condition
'!tx_slotnum' is not redundant
if (tx_slotnum > 2 || !tx_slotnum) {
^
sound/soc/codecs/rt1011.c:1994:6: note: Condition 'tx_slotnum' is
always true
if (tx_slotnum)
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302212527.55158-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On an imx8mq-evk the following error is seen:
[ 1.375809] wm8524-codec audio-codec: Failed to get mute line: -517
It happens because the codec driver may probe prior to the imx gpio
driver, which causes a probe defer.
Change to dev_err_probe() to avoid printing this error.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210301193328.2123511-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
v5.12-rc1 flags new warnings with make W=1, fix missing or broken
function descriptors.
sound/soc/codecs/nau8825.c:298: warning: wrong kernel-doc identifier
on line:
* Ramp up the headphone volume change gradually to target level.
sound/soc/codecs/nau8825.c:358: warning: expecting prototype for This
func(). Prototype was for nau8825_intlog10_dec3() instead
sound/soc/codecs/nau8825.c:411: warning: wrong kernel-doc identifier
on line:
* computes cross talk suppression sidetone gain.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210301174639.117017-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Constify a number of static structs that are never modified in RealTek
codecs. The most important patches are the first two, which constifies
snd_soc_dai_ops and sdw_slave_ops, both which contain function pointers.
The other two patches are for good measure, since I was already touching
the code there.
When doing this, I discovered sound/soc/codecs/rt1016.c is not in a
Makefile, so there is not really any way to build it (I added locally to
the Makefile to compile-test my changes). Is this expected or an oversight?
Rikard Falkeborn (4):
ASoC: rt*: Constify static struct sdw_slave_ops
ASoC: rt*: Constify static struct snd_soc_dai_ops
ASoC: rt*: Constify static struct acpi_device_id
ASoc: rt5631: Constify static struct coeff_clk_div
sound/soc/codecs/rt1011.c | 2 +-
sound/soc/codecs/rt1015.c | 4 ++--
sound/soc/codecs/rt1016.c | 4 ++--
sound/soc/codecs/rt1305.c | 2 +-
sound/soc/codecs/rt1308-sdw.c | 2 +-
sound/soc/codecs/rt1308.c | 2 +-
sound/soc/codecs/rt5631.c | 2 +-
sound/soc/codecs/rt5682-sdw.c | 4 ++--
sound/soc/codecs/rt700-sdw.c | 2 +-
sound/soc/codecs/rt700.c | 2 +-
sound/soc/codecs/rt711-sdw.c | 2 +-
sound/soc/codecs/rt711.c | 2 +-
sound/soc/codecs/rt715-sdw.c | 2 +-
sound/soc/codecs/rt715.c | 2 +-
14 files changed, 17 insertions(+), 17 deletions(-)
--
2.30.1
The variable hph_pwr_mode is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210215200501.90697-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
