Adds reject skbuff creation helper functions to ipv4/6 nf_reject
infrastructure. Use these functions for reject verdict in bridge
family.
Can be reused by all different families that support reject and
will not inject the reject packet through ip local out.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch is to add the function to make the abort chunk with
the error cause for new encapsulation port restart, defined
on Section 4.4 in draft-tuexen-tsvwg-sctp-udp-encaps-cons-03.
v1->v2:
- no change.
v2->v3:
- no need to call htons() when setting nep.cur_port/new_port.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_mtu_payload() is for calculating the frag size before making
chunks from a msg. So we should only add udphdr size to overhead
when udp socks are listening, as only then sctp can handle the
incoming sctp over udp packets and outgoing sctp over udp packets
will be possible.
Note that we can't do this according to transport->encap_port, as
different transports may be set to different values, while the
chunks were made before choosing the transport, we could not be
able to meet all rfc6951#section-5.6 recommends.
v1->v2:
- Add udp_port for sctp_sock to avoid a potential race issue, it
will be used in xmit path in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As rfc6951#section-5.4 says:
"After finding the SCTP association (which
includes checking the verification tag), the UDP source port MUST be
stored as the encapsulation port for the destination address the SCTP
packet is received from (see Section 5.1).
When a non-encapsulated SCTP packet is received by the SCTP stack,
the encapsulation of outgoing packets belonging to the same
association and the corresponding destination address MUST be
disabled."
transport encap_port should be updated by a validated incoming packet's
udp src port.
We save the udp src port in sctp_input_cb->encap_port, and then update
the transport in two places:
1. right after vtag is verified, which is required by RFC, and this
allows the existent transports to be updated by the chunks that
can only be processed on an asoc.
2. right before processing the 'init' where the transports are added,
and this allows building a sctp over udp connection by client with
the server not knowing the remote encap port.
3. when processing ootb_pkt and creating the temporary transport for
the reply pkt.
Note that sctp_input_cb->header is removed, as it's not used any more
in sctp.
v1->v2:
- Change encap_port as __be16 for sctp_input_cb.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
encap_port is added as per netns/sock/assoc/transport, and the
latter one's encap_port inherits the former one's by default.
The transport's encap_port value would mostly decide if one
packet should go out with udp encapsulated or not.
This patch also allows users to set netns' encap_port by sysctl.
v1->v2:
- Change to define encap_port as __be16 for sctp_sock, asoc and
transport.
v2->v3:
- No change.
v3->v4:
- Add 'encap_port' entry in ip-sysctl.rst.
v4->v5:
- Improve the description of encap_port in ip-sysctl.rst.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add the udp6 sock part in sctp_udp_sock_start/stop().
udp_conf.use_udp6_rx_checksums is set to true, as:
"The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP
checksum SHOULD be computed for IPv4 and IPv6"
says in rfc6951#section-5.3.
v1->v2:
- Add pr_err() when fails to create udp v6 sock.
- Add #if IS_ENABLED(CONFIG_IPV6) not to create v6 sock when ipv6 is
disabled.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add the functions to create/release udp4 sock,
and set the sock's encap_rcv to process the incoming udp encap
sctp packets. In sctp_udp_rcv(), as we can see, all we need to
do is fix the transport header for sctp_rcv(), then it would
implement the part of rfc6951#section-5.4:
"When an encapsulated packet is received, the UDP header is removed.
Then, the generic lookup is performed, as done by an SCTP stack
whenever a packet is received, to find the association for the
received SCTP packet"
Note that these functions will be called in the last patch of
this patchset when enabling this feature.
v1->v2:
- Add pr_err() when fails to create udp v4 sock.
v2->v3:
- Add 'select NET_UDP_TUNNEL' in sctp Kconfig.
v3->v4:
- No change.
v4->v5:
- Change to set udp_port to 0 by default.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some identifiers have different names between their prototypes
and the kernel-doc markup.
Others need to be fixed, as kernel-doc markups should use this format:
identifier - description
In the specific case of __sta_info_flush(), add a documentation
for sta_info_flush(), as this one is the one used outside
sta_info.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/978d35eef2dc76e21c81931804e4eaefbd6d635e.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no known users of this driver as of October 2020, and it will
be removed unless someone turns out to still need it in future releases.
According to https://en.wikipedia.org/wiki/List_of_WiMAX_networks, there
have been many public wimax networks, but it appears that many of these
have migrated to LTE or discontinued their service altogether.
As most PCs and phones lack WiMAX hardware support, the remaining
networks tend to use standalone routers. These almost certainly
run Linux, but not a modern kernel or the mainline wimax driver stack.
NetworkManager appears to have dropped userspace support in 2015
https://bugzilla.gnome.org/show_bug.cgi?id=747846, the
www.linuxwimax.org
site had already shut down earlier.
WiMax is apparently still being deployed on airport campus networks
("AeroMACS"), but in a frequency band that was not supported by the old
Intel 2400m (used in Sandy Bridge laptops and earlier), which is the
only driver using the kernel's wimax stack.
Move all files into drivers/staging/wimax, including the uapi header
files and documentation, to make it easier to remove it when it gets
to that. Only minimal changes are made to the source files, in order
to make it possible to port patches across the move.
Also remove the MAINTAINERS entry that refers to a broken mailing
list and website.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Suggested-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix a possible memory leak at xsk socket close that is caused by the
refcounting of the umem object being wrong. The reference count of the
umem was decremented only after the pool had been freed. Note that if
the buffer pool is destroyed, it is important that the umem is
destroyed after the pool, otherwise the umem would disappear while the
driver is still running. And as the buffer pool needs to be destroyed
in a work queue, the umem is also (if its refcount reaches zero)
destroyed after the buffer pool in that same work queue.
What was missing is that the refcount also needs to be decremented
when the pool is not freed and when the pool has not even been
created. The first case happens when the refcount of the pool is
higher than 1, i.e. it is still being used by some other socket using
the same device and queue id. In this case, it is safe to decrement
the refcount of the umem outside of the work queue as the umem will
never be freed because the refcount of the umem is always greater than
or equal to the refcount of the buffer pool. The second case is if the
buffer pool has not been created yet, i.e. the socket was closed
before it was bound but after the umem was created. In this case, it
is safe to destroy the umem outside of the work queue, since there is
no pool that can use it by definition.
Fixes: 1c1efc2af1 ("xsk: Create and free buffer pool independently from umem")
Reported-by: syzbot+eb71df123dc2be2c1456@syzkaller.appspotmail.com
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1603801921-2712-1-git-send-email-magnus.karlsson@gmail.com
Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late
in the 5.9 cycle started depending on a return code from
a function which changed with the 5.10 PR from the usb subsystem
Current release - regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous releases - regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu()
to synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems;
the property is not populated correctly by the firmware,
but firmware configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is
light and only wants to schedule napi (and do so through
a _irqoff() variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ceke
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
This patch fixes the issue due to:
BUG: KASAN: slab-out-of-bounds in nft_flow_rule_create+0x622/0x6a2
net/netfilter/nf_tables_offload.c:40
Read of size 8 at addr ffff888103910b58 by task syz-executor227/16244
The error happens when expr->ops is accessed early on before performing the boundary check and after nft_expr_next() moves the expr to go out-of-bounds.
This patch checks the boundary condition before expr->ops that fixes the slab-out-of-bounds Read issue.
Add nft_expr_more() and use it to fix this problem.
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl+JNGYACgkQCF8+vY7k
4RV/TA//ZoRoMQE5B6zwO4kOGILMbmW2uepjoEysLgus2ctkTUoRkpNLWS3SozcU
6c/eW1rC4Fji24te6lwusciZa5zQgbGMjFYk1LhnJ65lJA+kQ+kV1DGz/ZWtklMM
gLX20+tQADqGl+u2dmFCvmRhPWJ9nzt1C0auN7dGeu+9g97GnhKG6o2Kv/nVCb68
qMmAs9UrfN24DO5G1ixkdY08nSNJPrpgQnIR2ruUysUII/yTTtcnmHDbH3WWL6+9
2P87AZ6zsa3FdBhAjmG5YJklQgPkLFWEykHMTqq/Mkcpff/JB/AayrL6XNB2QoZb
YXLHJp3Na6iBmdmHhecg+VQDgz28UfMk+p+HFoJh8RTtJa9/qJvYdJmIE/mUPrnY
gL4jNgMVwkptGHXh7IRuSLysT5heJPMQss6TfZ6yYadeOIpx7W8MCAYnGffiElLQ
hmKdmyCszS3SERJz40EOBdr2NQYcDEUt2NtEhdVfium21A4PFOdJlCejifGhJyzP
n1QcyMXHnh/d4zecA6fcD0LVyxBgngeKEvdtOLZJ1ubxWwHhgWTN8R4HedoN2Nb9
cLEUK8Td+9n2RVS8UED4BBI+6vfN3Y6Syjvy8qD3pCs4SBcu3k790mf47t2QhkEq
+Ho06gdrGJdEcSDO8zVY7qjZX/GX/dbRHCb5CRokL5FmNWhXd/Y=
=26wi
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAl+ItRwACgkQMUZtbf5S
IrtTMg//UxpdR/MirT1DatBU0K/UGAZY82hV7F/UC8tPgjfHZeHvWlDFxfi3YP81
PtPKbhRZ7DhwBXefUp6nY3UdvjftrJK2lJm8prJUPSsZRye8Wlcb7y65q7/P2y2U
Efucyopg6RUrmrM0DUsIGYGJgylQLHnMYUl/keCsD4t5Bp4ksyi9R2t5eitGoWzh
r3QGdbSa0AuWx4iu0i+tqp6Tj0ekMBMXLVb35dtU1t0joj2KTNEnSgABN3prOa8E
iWYf2erOau68Ogp3yU3miCy0ZU4p/7qGHTtzbcp677692P/ekak6+zmfHLT9/Pjy
2Stq2z6GoKuVxdktr91D9pA3jxG4LxSJmr0TImcGnXbvkMP3Ez3g9RrpV5fn8j6F
mZCH8TKZAoD5aJrAJAMkhZmLYE1pvDa7KolSk8WogXrbCnTEb5Nv8FHTS1Qnk3yl
wSKXuvutFVNLMEHCnWQLtODbTST9DI/aOi6EctPpuOA/ZyL1v3pl+gfp37S+LUTe
owMnT/7TdvKaTD0+gIyU53M6rAWTtr5YyRQorX9awIu/4Ha0F0gYD7BJZQUGtegp
HzKt59NiSrFdbSH7UdyemdBF4LuCgIhS7rgfeoUXMXmuPHq7eHXyHZt5dzPPa/xP
81P0MAvdpFVwg8ij2yp2sHS7sISIRKq17fd1tIewUabxQbjXqPc=
=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Changeset df78a0c0b6 ("nl80211: S1G band and channel definitions")
added a new parameter, but didn't add the corresponding kernel-doc
markup, as repoted when doing "make htmldocs":
./include/net/cfg80211.h:471: warning: Function parameter or member 's1g_cap' not described in 'ieee80211_supported_band'
Add a documentation for it.
Fixes: df78a0c0b6 ("nl80211: S1G band and channel definitions")
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This definition is used by the iptables legacy UAPI, restore it.
Fixes: d3519cb89f ("netfilter: nf_tables: add inet ingress support")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dump vlan tag and proto for the usual vlan offload case if the
NF_LOG_MACDECODE flag is set on. Without this information the logging is
misleading as there is no reference to the VLAN header.
[12716.993704] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0800 SRC=192.168.10.2 DST=172.217.168.163 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=2548 DF PROTO=TCP SPT=55848 DPT=80 WINDOW=501 RES=0x00 ACK FIN URGP=0
[12721.157643] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0806 ARP HTYPE=1 PTYPE=0x0800 OPCODE=2 MACSRC=86:6c:92:ea:d6:73 IPSRC=192.168.10.2 MACDST=0e:3b:eb:86:73:76 IPDST=192.168.10.1
Fixes: 83e96d443b ("netfilter: log: split family specific code to nf_log_{ip,ip6,common}.c files")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull copy_and_csum cleanups from Al Viro:
"Saner calling conventions for csum_and_copy_..._user() and friends"
[ Removing 800+ lines of code and cleaning stuff up is good - Linus ]
* 'work.csum_and_copy' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ppc: propagate the calling conventions change down to csum_partial_copy_generic()
amd64: switch csum_partial_copy_generic() to new calling conventions
sparc64: propagate the calling convention changes down to __csum_partial_copy_...()
xtensa: propagate the calling conventions change down into csum_partial_copy_generic()
mips: propagate the calling convention change down into __csum_partial_copy_..._user()
mips: __csum_partial_copy_kernel() has no users left
mips: csum_and_copy_{to,from}_user() are never called under KERNEL_DS
sparc32: propagate the calling conventions change down to __csum_partial_copy_sparc_generic()
i386: propagate the calling conventions change down to csum_partial_copy_generic()
sh: propage the calling conventions change down to csum_partial_copy_generic()
m68k: get rid of zeroing destination on error in csum_and_copy_from_user()
arm: propagate the calling convention changes down to csum_partial_copy_from_user()
alpha: propagate the calling convention changes down to csum_partial_copy.c helpers
saner calling conventions for csum_and_copy_..._user()
csum_and_copy_..._user(): pass 0xffffffff instead of 0 as initial sum
csum_partial_copy_nocheck(): drop the last argument
unify generic instances of csum_partial_copy_nocheck()
icmp_push_reply(): reorder adding the checksum up
skb_copy_and_csum_bits(): don't bother with the last argument
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-10-12
The main changes are:
1) The BPF verifier improvements to track register allocation pattern, from Alexei and Yonghong.
2) libbpf relocation support for different size load/store, from Andrii.
3) bpf_redirect_peer() helper and support for inner map array with different max_entries, from Daniel.
4) BPF support for per-cpu variables, form Hao.
5) sockmap improvements, from John.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Inspect the reply packets coming from DR/TUN and refresh connection
state and timeout, from longguang yue and Julian Anastasov.
2) Series to add support for the inet ingress chain type in nf_tables.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a new ingress hook for the inet family. The inet ingress
hook emulates the IP receive path code, therefore, unclean packets are
drop before walking over the ruleset in this basechain.
This patch also introduces the nft_base_chain_netdev() helper function
to check if this hook is bound to one or more devices (through the hook
list infrastructure). This check allows to perform the same handling for
the inet ingress as it would be a netdev ingress chain from the control
plane.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* fixes for the recent S1G work
* a docbook build time improvement
* API to pass beacon rate to lower-level driver
-----BEGIN PGP SIGNATURE-----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=TrMG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A handful of changes:
* fixes for the recent S1G work
* a docbook build time improvement
* API to pass beacon rate to lower-level driver
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new attribute NLMSGERR_ATTR_POLICY to the extended ACK
to advertise the policy, e.g. if an attribute was out of range,
you'll know the range that's permissible.
Add new NL_SET_ERR_MSG_ATTR_POL() and NL_SET_ERR_MSG_ATTR_POL()
macros to set this, since realistically it's only useful to do
this when the bad attribute (offset) is also returned.
Use it in lib/nlattr.c which practically does all the policy
validation.
v2:
- add and use netlink_policy_dump_attr_size_estimate()
v3:
- remove redundant break
v4:
- really remove redundant break ... sorry
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove one of the two instances of the function prototype for
tls_validate_xmit_skb().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Pismenny <borisp@nvidia.com>
Cc: Aviad Yehezkel <aviadye@nvidia.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add remote reload stats to hold the history of actions performed due
devlink reload commands initiated by remote host. For example, in case
firmware activation with reset finished successfully but was initiated
by remote host.
The function devlink_remote_reload_actions_performed() is exported to
enable drivers update on remote reload actions performed as it was not
initiated by their own devlink instance.
Expose devlink remote reload stats to the user through devlink dev get
command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
remote_reload:
driver_reinit 0 fw_activate 0 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
remote_reload:
driver_reinit 1 fw_activate 1 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 0,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
},
"remote_reload": {
"driver_reinit": 1,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload stats to hold the history per reload action type and limit.
For example, the number of times fw_activate has been performed on this
device since the driver module was added or if the firmware activation
was performed with or without reset.
Add devlink notification on stats update.
Expose devlink reload stats to the user through devlink dev get command.
Examples:
$ devlink dev show
pci/0000:82:00.0:
stats:
reload:
driver_reinit 2 fw_activate 1 fw_activate_no_reset 0
pci/0000:82:00.1:
stats:
reload:
driver_reinit 1 fw_activate 0 fw_activate_no_reset 0
$ devlink dev show -jp
{
"dev": {
"pci/0000:82:00.0": {
"stats": {
"reload": {
"driver_reinit": 2,
"fw_activate": 1,
"fw_activate_no_reset": 0
}
}
},
"pci/0000:82:00.1": {
"stats": {
"reload": {
"driver_reinit": 1,
"fw_activate": 0,
"fw_activate_no_reset": 0
}
}
}
}
}
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add reload limit to demand restrictions on reload actions.
Reload limits supported:
no_reset: No reset allowed, no down time allowed, no link flap and no
configuration is lost.
By default reload limit is unspecified and so no constraints on reload
actions are required.
Some combinations of action and limit are invalid. For example, driver
can not reinitialize its entities without any downtime.
The no_reset reload limit will have usecase in this patchset to
implement restricted fw_activate on mlx5.
Have the uapi parameter of reload limit ready for future support of
multiselection.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink reload action to allow the user to request a specific reload
action. The action parameter is optional, if not specified then devlink
driver re-init action is used (backward compatible).
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.
Reload actions supported are:
driver_reinit: driver entities re-initialization, applying devlink-param
and devlink-resource values.
fw_activate: firmware activate.
command examples:
$devlink dev reload pci/0000:82:00.0 action driver_reinit
reload_actions_performed:
driver_reinit
$devlink dev reload pci/0000:82:00.0 action fw_activate
reload_actions_performed:
driver_reinit fw_activate
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kmalloc() of sufficiently big portion of memory is cache-aligned
in regular conditions. If some debugging options are used,
there is no reason qdisc structures would need 64-byte alignment
if most other kernel structures are not aligned.
This get rid of QDISC_ALIGN and QDISC_ALIGNTO.
Addition of privdata field will help implementing
the reverse of qdisc_priv() and documents where
the private data is.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd.
This information needs to be passed to the driver when the rate control
is offloaded to the firmware. The driver capability of allowing beacon
rate is already validated in cfg80211, so simply passing the rate
information to the driver is enough.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1601762658-15627-1-git-send-email-rmanohar@codeaurora.org
[adjust commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't have good validation policy for existing unsigned int attrs
which serve as flags (for new ones we could use NLA_BITFIELD32).
With increased use of policy dumping having the validation be
expressed as part of the policy is important. Add validation
policy in form of a mask of supported/valid bits.
Support u64 in the uAPI to be future-proof, but really for now
the embedded mask member can only hold 32 bits, so anything with
bit 32+ set will always fail validation.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of policies which check if type is a uint or sint.
Factor the checking against the list of value sizes to a helper
for easier reuse.
v2: - new patch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide away from DSA drivers how devlink works.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink port regions, via simple
wrappers.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow regions to be registered to a devlink port. The same netlink API
is used, but the port index is provided to indicate when a region is a
port region as opposed to a device region.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers want to create regions on devlink ports as well as the
devlink device instance, in order to export registers and other tables
per port. To keep all this code together in the drivers, have the
devlink ports registered early, so the setup() method can setup both
device and port devlink regions.
v3:
Remove dp->setup
Move common code out of switch statement.
Fix wrong goto
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Rename 'searched' column to 'clashres' in conntrack /proc/ stats
to amend a recent patch, from Florian Westphal.
2) Remove unused nft_data_debug(), from YueHaibing.
3) Remove unused definitions in IPVS, also from YueHaibing.
4) Fix user data memleak in tables and objects, this is also amending
a recent patch, from Jose M. Guisado.
5) Use nla_memdup() to allocate user data in table and objects, also
from Jose M. Guisado
6) User data support for chains, from Jose M. Guisado
7) Remove unused definition in nf_tables_offload, from YueHaibing.
8) Use kvzalloc() in ip_set_alloc(), from Vasily Averin.
9) Fix false positive reported by lockdep in nfnetlink mutexes,
from Florian Westphal.
10) Extend fast variant of cmp for neq operation, from Phil Sutter.
11) Implement fast bitwise variant, also from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical use of bitwise expression is to mask out parts of an IP
address when matching on the network part only. Optimize for this common
use with a fast variant for NFT_BITWISE_BOOL-type expressions operating
on 32bit-sized values.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a boolean indicating NFT_CMP_NEQ. To include it into the match
decision, it is sufficient to XOR it with the data comparison's result.
While being at it, store the mask that is calculated during expression
init and free the eval routine from having to recalculate it each time.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implement TCA_VLAN_ACT_POP_ETH and TCA_VLAN_ACT_PUSH_ETH, to
respectively pop and push a base Ethernet header at the beginning of a
frame.
POP_ETH is just a matter of pulling ETH_HLEN bytes. VLAN tags, if any,
must be stripped before calling POP_ETH.
PUSH_ETH is restricted to skbs with no mac_header, and only the MAC
addresses can be configured. The Ethertype is automatically set from
skb->protocol. These restrictions ensure that all skb's fields remain
consistent, so that this action can't confuse other part of the
networking stack (like GSO).
Since openvswitch already had these actions, consolidate the code in
skbuff.c (like for vlan and mpls push/pop).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the policy dump code a bit to support adding multiple
policies to a single dump, in order to e.g. support per-op
policies in generic netlink.
v2:
- move kernel-doc to implementation [Jakub]
- squash the first patch to not flip-flop on the prototype
[Jakub]
- merge netlink_policy_dump_get_policy_idx() with the old
get_policy_idx() we already had
- rebase without Jakub's patch to have per-op dump
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add policy to the struct genl_ops structure, this time
with maxattr, so it can be used properly.
Propagate .policy and .maxattr from the family
in genl_get_cmd() if needed, this way the rest of the
code does not have to worry if the policy is per op
or global.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever netlink dump uses more than 2 cb->args[] entries
code gets hard to read. We're about to add more state to
ctrl_dumppolicy() so create a structure.
Since the structure is typed and clearly named we can remove
the local fam_id variable and use ctx->fam_id directly.
v3:
- rebase onto explicit free fix
v1:
- s/nl_policy_dump/netlink_policy_dump_state/
- forward declare struct netlink_policy_dump_state,
and move from passing unsigned long to actual pointer type
- add build bug on
- u16 fam_id
- s/args/ctx/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are holes and oversized members in struct genl_family.
Before: /* size: 104, cachelines: 2, members: 16 */
After: /* size: 88, cachelines: 2, members: 16 */
The command field in struct genlmsghdr is a u8, so no point
in the operation count being 32 bit. Also operation 0 is
usually undefined, so we only need 255 entries.
netnsok and parallel_ops are only ever initialized to true.
We can grow the fields as needed, compiler should warn us
if someone tries to assign larger constants.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink callback, .trap_group_action_set(), which can be used
by device drivers which do not support controlling the action (drop,
trap) on each trap but rather on the entire group trap.
If this new callback is populated, it will take precedence over the
.trap_action_set() callback when the user requests a change of all the
traps in a group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add parser error drop packet traps, so that capable device driver could
register them with devlink. The new packet trap group holds any drops of
packets which were marked by the device as erroneous during header
parsing. Add documentation for every added packet trap and packet trap
group.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl92/IsACgkQB8qZga/f
l8QrBxAAi8HJdFyZtCIuLrXL3KHzey5AjmrYuHdsFcdk8NJZkEco17I3l05D9ek6
76VvqjiYzDwdmgoHr3yz0K7pOAoTRpBKlaecvZLPXWf2bVhebWSU5EPcrTZHolrJ
JBoBj4FU6Im/MnFbeiKxPj3M+NTQrLdekODSeaC5hFhi/oSF9lap6RMC8sz4YrVp
9yKzB8zjz+eL4wL3EsztEzpTxbvHTaVMe0XBVou7Fg2ZauJGwqMxpIukpMWUmmNr
EequhVFpdlXbVMle8wP4ZR58c4+O1kbRoYL9WhAILtdDhCKfLccWXnlUjzuQlCeB
RH/jzG7AlVhm972oUuqG9szAcU8hEgWdsNEML7pilXmFk/ZSNLpUZfZCAILn+Gd3
8oMQnXp2br+DLzf1SO7cxpL2KrTNjrb4gcJVBJ9eBlDjK/64N22MqZkpOKcMxq51
ocmf1MJ1TbAbZn/kY2hsoaPYt2+bm1umMa/t/Pwuds+xKZEOOuPNgZQILcAsfJZB
2OWDDT+RNLo/K4mPETtyQQZoCxAWB9n/CcnU+UTsmnUmMsEnCEbPnbYKBrc6jX1l
jSP6XUD8fxhB2lfW+SPtQPnAi86+gblXVvEO8zm0+ez3juItlIsVcRY8ey/j9N1F
uorpycvrfl6+Q1+mmhe6et2r+TLdGs73I0PJ44HRA9JZexKBrDg=
=B9Xl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, this time with:
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-10-02
1) Add a full xfrm compatible layer for 32-bit applications on
64-bit kernels. From Dmitry Safonov.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Upstream commit a95bc734e6 ]
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 0813a84156 ("bpf: tcp: Allow bpf prog to write and parse TCP header option")
unnecessarily introduced bpf_skops_init_child() which limited the child
sk from inheriting all bpf_sock_ops_cb_flags of the listen sk. That
breaks existing user expectation.
This patch removes the bpf_skops_init_child() and just allows
sock_copy() to do its job to copy everything from listen sk to
the child sk.
Fixes: 0813a84156 ("bpf: tcp: Allow bpf prog to write and parse TCP header option")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201002013448.2542025-1-kafai@fb.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-10-01
The following pull-request contains BPF updates for your *net-next* tree.
We've added 90 non-merge commits during the last 8 day(s) which contain
a total of 103 files changed, 7662 insertions(+), 1894 deletions(-).
Note that once bpf(/net) tree gets merged into net-next, there will be a small
merge conflict in tools/lib/bpf/btf.c between commit 1245008122 ("libbpf: Fix
native endian assumption when parsing BTF") from the bpf tree and the commit
3289959b97 ("libbpf: Support BTF loading and raw data output in both endianness")
from the bpf-next tree. Correct resolution would be to stick with bpf-next, it
should look like:
[...]
/* check BTF magic */
if (fread(&magic, 1, sizeof(magic), f) < sizeof(magic)) {
err = -EIO;
goto err_out;
}
if (magic != BTF_MAGIC && magic != bswap_16(BTF_MAGIC)) {
/* definitely not a raw BTF */
err = -EPROTO;
goto err_out;
}
/* get file size */
[...]
The main changes are:
1) Add bpf_snprintf_btf() and bpf_seq_printf_btf() helpers to support displaying
BTF-based kernel data structures out of BPF programs, from Alan Maguire.
2) Speed up RCU tasks trace grace periods by a factor of 50 & fix a few race
conditions exposed by it. It was discussed to take these via BPF and
networking tree to get better testing exposure, from Paul E. McKenney.
3) Support multi-attach for freplace programs, needed for incremental attachment
of multiple XDP progs using libxdp dispatcher model, from Toke Høiland-Jørgensen.
4) libbpf support for appending new BTF types at the end of BTF object, allowing
intrusive changes of prog's BTF (useful for future linking), from Andrii Nakryiko.
5) Several BPF helper improvements e.g. avoid atomic op in cookie generator and add
a redirect helper into neighboring subsys, from Daniel Borkmann.
6) Allow map updates on sockmaps from bpf_iter context in order to migrate sockmaps
from one to another, from Lorenz Bauer.
7) Fix 32 bit to 64 bit assignment from latest alu32 bounds tracking which caused
a verifier issue due to type downgrade to scalar, from John Fastabend.
8) Follow-up on tail-call support in BPF subprogs which optimizes x64 JIT prologue
and epilogue sections, from Maciej Fijalkowski.
9) Add an option to perf RB map to improve sharing of event entries by avoiding remove-
on-close behavior. Also, add BPF_PROG_TEST_RUN for raw_tracepoint, from Song Liu.
10) Fix a crash in AF_XDP's socket_release when memory allocation for UMEMs fails,
from Magnus Karlsson.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.
Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.
Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert drop monitor to use the recently introduced
'devlink_trap_report' tracepoint instead of having devlink call into
drop monitor.
This is both consistent with software originated drops ('kfree_skb'
tracepoint) and also allows drop monitor to be built as a module and
still report hardware originated drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever host is under very high memory pressure,
__tcp_send_ack() skb allocation fails, and we setup
a 200 ms (TCP_DELACK_MAX) timer before retrying.
On hosts with high number of TCP sockets, we can spend
considerable amount of cpu cycles in these attempts,
add high pressure on various spinlocks in mm-layer,
ultimately blocking threads attempting to free space
from making any progress.
This patch adds standard exponential backoff to avoid
adding fuel to the fire.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP has been using it to work around the possibility of tcp_delack_timer()
finding the socket owned by user.
After commit 6f458dfb40 ("tcp: improve latencies of timer triggered events")
we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery,
so we can get rid of icsk_ack.blocked
This frees space that following patch will reuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With its use in BPF, the cookie generator can be called very frequently
in particular when used out of cgroup v2 hooks (e.g. connect / sendmsg)
and attached to the root cgroup, for example, when used in v1/v2 mixed
environments. In particular, when there's a high churn on sockets in the
system there can be many parallel requests to the bpf_get_socket_cookie()
and bpf_get_netns_cookie() helpers which then cause contention on the
atomic counter.
As similarly done in f991bd2e14 ("fs: introduce a per-cpu last_ino
allocator"), add a small helper library that both can use for the 64 bit
counters. Given this can be called from different contexts, we also need
to deal with potential nested calls even though in practice they are
considered extremely rare. One idea as suggested by Eric Dumazet was
to use a reverse counter for this situation since we don't expect 64 bit
overflows anyways; that way, we can avoid bigger gaps in the 64 bit
counter space compared to just batch-wise increase. Even on machines
with small number of cores (e.g. 4) the cookie generation shrinks from
min/max/med/avg (ns) of 22/50/40/38.9 down to 10/35/14/17.3 when run
in parallel from multiple CPUs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Link: https://lore.kernel.org/bpf/8a80b8d27d3c49f9a14e1d5213c19d8be87d1dc8.1601477936.git.daniel@iogearbox.net
Enables storing userdata for nft_chain. Field udata points to user data
and udlen stores its length.
Adds new attribute flag NFTA_CHAIN_USERDATA.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While chasing in_interrupt() (ab)use in drivers it turned out that the
caif_spi driver has never been in use since the driver was merged 10 years
ago. There never was any matching code which provides a platform device.
The driver has not seen any update (asided of treewide changes and
cleanups) since 8 years and the maintainers vanished from the planet.
So analysing the potential contexts and the (in)correctness of
in_interrupt() usage is just a pointless exercise.
Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-09-29
Here's the main bluetooth-next pull request for 5.10:
- Multiple fixes to suspend/resume handling
- Added mgmt events for controller suspend/resume state
- Improved extended advertising support
- btintel: Enhanced support for next generation controllers
- Added Qualcomm Bluetooth SoC WCN6855 support
- Several other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Validation flags are missing kdoc, add it.
Fixes: ef6243acb4 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMCD version 2 the CHIDs of ISM devices are needed for the
CLC handshake.
This patch provides the new callback to retrieve the CHID of an
ISM device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD version 2 defines a System Enterprise ID (short SEID).
This patch contains the SEID creation and adds the callback to
retrieve the created SEID.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately recent Intel NIC designs share the UDP port table
across netdevs. So far the UDP tunnel port state was maintained
per netdev, we need to extend that to cater to Intel NICs.
Expect NICs to allocate the info structure dynamically and link
to the state from there. All the shared NICs will record port
offload information in the one instance of the table so we need
to make sure that the use count can accommodate larger numbers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-09-28
1) Fix a build warning in ip_vti if CONFIG_IPV6 is not set.
From YueHaibing.
2) Restore IPCB on espintcp before handing the packet to xfrm
as the information there is still needed.
From Sabrina Dubroca.
3) Fix pmtu updating for xfrm interfaces.
From Sabrina Dubroca.
4) Some xfrm state information was not cloned with xfrm_do_migrate.
Fixes to clone the full xfrm state, from Antony Antony.
5) Use the correct address family in xfrm_state_find. The struct
flowi must always be interpreted along with the original
address family. This got lost over the years.
Fix from Herbert Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to request that interface-iterator does NOT iterate
over interfaces that are not sdata-in-driver. This will allow
us to fix crashes in ath10k (and possibly other drivers).
To summarize Johannes' explanation:
Consider
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
If you apply this scenario to a restart, which ought to be functionally
equivalent to the normal startup, just compressed in time, you're
basically saying that today you get
add interface wlan0
add interface wlan1
iterate active interfaces -> wlan0 wlan1 wlan2 << problem here
add interface wlan2
iterate active interfaces -> wlan0 wlan1 wlan2
which yeah, totally seems wrong.
But fixing that to be
add interface wlan0
add interface wlan1
iterate active interfaces ->
<nothing>
add interface wlan2
iterate active interfaces -> <nothing>
(or
maybe -> wlan0 wlan1 wlan2 if the reconfig already completed)
This is also at least somewhat wrong, but better to not iterate
over something that exists in the driver than iterate over something
that does not. Originally the first issue was causing crashes in
testing with lots of station vdevs on an ath10k radio, combined
with firmware crashing.
I ran with a similar patch for years with no obvious bad results,
including significant testing with ath9k and ath10k.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20200922191957.25257-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G doesn't have legacy (sband->bitrates) rates, only MCS.
For now, just send a frame at MCS 0 if a low rate is
requested. Note we also redefine (since we're out of TX
flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G
MCS. This is probably OK as VHT MCS is not valid on S1G
band and vice versa.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-12-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_S1G_CAPABILITY can be passed along with
NL80211_ATTR_S1G_CAPABILITY_MASK to NL80211_CMD_ASSOCIATE
to indicate S1G capabilities which should override the
hardware capabilities in eg. the association request.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-4-thomas@adapt-ip.com
[johannes: always require both attributes together, commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For all DSA formats that don't use tail tags, it looks like behind the
obscure number crunching they're all doing the same thing: locating the
real EtherType behind the DSA tag. Nonetheless, this is not immediately
obvious, so create a generic helper for those DSA taggers that put the
header before the EtherType.
Another assumption for the generic function is that the DSA tags are of
equal length on RX and on TX. Prior to the previous patch, this was not
true for ocelot and for gswip. The problem was resolved for ocelot, but
for gswip it still remains, so that can't use this helper yet.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sections of device flash may contain settings or device identifying
information. When performing a flash update, it is generally expected
that these settings and identifiers are not overwritten.
However, it may sometimes be useful to allow overwriting these fields
when performing a flash update. Some examples include, 1) customizing
the initial device config on first programming, such as overwriting
default device identifying information, or 2) reverting a device
configuration to known good state provided in the new firmware image, or
3) in case it is suspected that current firmware logic for managing the
preservation of fields during an update is broken.
Although some devices are able to completely separate these types of
settings and fields into separate components, this is not true for all
hardware.
To support controlling this behavior, a new
DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK is defined. This is an
nla_bitfield32 which will define what subset of fields in a component
should be overwritten during an update.
If no bits are specified, or of the overwrite mask is not provided, then
an update should not overwrite anything, and should maintain the
settings and identifiers as they are in the previous image.
If the overwrite mask has the DEVLINK_FLASH_OVERWRITE_SETTINGS bit set,
then the device should be configured to overwrite any of the settings in
the requested component with settings found in the provided image.
Similarly, if the DEVLINK_FLASH_OVERWRITE_IDENTIFIERS bit is set, the
device should be configured to overwrite any device identifiers in the
requested component with the identifiers from the image.
Multiple overwrite modes may be combined to indicate that a combination
of the set of fields that should be overwritten.
Drivers which support the new overwrite mask must set the
DEVLINK_SUPPORT_FLASH_UPDATE_OVERWRITE_MASK in the
supported_flash_update_params field of their devlink_ops.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the bpf_sk_storage_*() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
A micro benchmark has been done on a "cgroup_skb/egress" bpf program
which does a bpf_sk_storage_get(). It was driven by netperf doing
a 4096 connected UDP_STREAM test with 64bytes packet.
The stats from "kernel.bpf_stats_enabled" shows no meaningful difference.
The sk_storage_get_btf_proto, sk_storage_delete_btf_proto,
btf_sk_storage_get_proto, and btf_sk_storage_delete_proto are
no longer needed, so they are removed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000402.3856307-1-kafai@fb.com
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit cfde141ea3 ("mptcp: move option parsing into
mptcp_incoming_options()"), the 3rd function argument is no longer used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a new helper sk_stop_timer_sync, it deactivates a timer
like sk_stop_timer, but waits for the handler to finish.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TC actions call tcf_idr_insert() for new action at the end
of their ->init(), so we can actually move it to a central place
in tcf_action_init_1().
And once the action is inserted into the global IDR, other parallel
process could free it immediately as its refcnt is still 1, so we can
not fail after this, we need to move it after the goto action
validation to avoid handling the failure case after insertion.
This is found during code review, is not directly triggered by syzbot.
And this prepares for the next patch.
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide compat_xfrm_userpolicy_info translation for xfrm setsocketopt().
Reallocate buffer and put the missing padding for 64-bit message.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Provide the user-to-kernel translator under XFRM_USER_COMPAT, that
creates for 32-bit xfrm-user message a 64-bit translation.
The translation is afterwards reused by xfrm_user code just as if
userspace had sent 64-bit message.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Provide the kernel-to-user translator under XFRM_USER_COMPAT, that
creates for 64-bit xfrm-user message a 32-bit translation and puts it
in skb's frag_list. net/compat.c layer provides MSG_CMSG_COMPAT to
decide if the message should be taken from skb or frag_list.
(used by wext-core which has also an ABI difference)
Kernel sends 64-bit xfrm messages to the userspace for:
- multicast (monitor events)
- netlink dumps
Wire up the translator to xfrm_nlmsg_multicast().
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a skeleton for xfrm_compat module and provide API to register it in
xfrm_state.ko. struct xfrm_translator will have function pointers to
translate messages received from 32-bit userspace or to be sent to it
from 64-bit kernel.
module_get()/module_put() are used instead of rcu_read_lock() as the
module will vmalloc() memory for translation.
The new API is registered with xfrm_state module, not with xfrm_user as
the former needs translator for user_policy set by setsockopt() and
xfrm_user already uses functions from xfrm_state.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-09-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 95 non-merge commits during the last 22 day(s) which contain
a total of 124 files changed, 4211 insertions(+), 2040 deletions(-).
The main changes are:
1) Full multi function support in libbpf, from Andrii.
2) Refactoring of function argument checks, from Lorenz.
3) Make bpf_tail_call compatible with functions (subprograms), from Maciej.
4) Program metadata support, from YiFei.
5) bpf iterator optimizations, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
* some AP-side infrastructure for FILS discovery and
unsolicited probe resonses
* a major rework of the encapsulation/header conversion
offload from Felix, to fit better with e.g. AP_VLAN
interfaces
* performance fix for VHT A-MPDU size, don't limit to HT
* some initial patches for S1G (sub 1 GHz) support, more
will come in this area
* minor cleanups
-----BEGIN PGP SIGNATURE-----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=Bnsm
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* some AP-side infrastructure for FILS discovery and
unsolicited probe resonses
* a major rework of the encapsulation/header conversion
offload from Felix, to fit better with e.g. AP_VLAN
interfaces
* performance fix for VHT A-MPDU size, don't limit to HT
* some initial patches for S1G (sub 1 GHz) support, more
will come in this area
* minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating ancestor_size with IPv6 enabled, simply using
sizeof(struct ipv6_pinfo) doesn't account for extra bytes needed for
alignment in the struct sctp6_sock. On x86, there aren't any extra
bytes, but on ARM the ipv6_pinfo structure is aligned on an 8-byte
boundary so there were 4 pad bytes that were omitted from the
ancestor_size calculation. This would lead to corruption of the
pd_lobby pointers, causing an oops when trying to free the sctp
structure on socket close.
Fixes: 636d25d557 ("sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant")
Signed-off-by: Henry Ptasinski <hptasinski@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the DSA drivers to implement the devlink call to get info info,
e.g. driver name, firmware version, ASIC ID, etc.
v2:
Combine declaration and the assignment on a single line.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.
v4:
Add missing kerneldoc for ICE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may have multiple regions which can be dumped using one
function. However, for this to work, additional information is
needed. Add a priv member to the ops structure for the driver to use
however it likes.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev flash status notify function parameter lists are getting
rather long, so add a struct to be filled and passed rather than
continuously changing the function signatures.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timeout element to the DEVLINK_CMD_FLASH_UPDATE_STATUS
netlink message for use by a userland utility to show that
a particular firmware flash activity may take a long but
bounded time to finish. Also add a handy helper for drivers
to make use of the new timeout value.
UI usage hints:
- if non-zero, add timeout display to the end of the status line
[component] status_msg ( Xm Ys : Am Bs )
using the timeout value for Am Bs and updating the Xm Ys
every second
- if the timeout expires while awaiting the next update,
display something like
[component] status_msg ( timeout reached : Am Bs )
- if new status notify messages are received, remove
the timeout and start over
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mac80211 support to configure unsolicited
broadcast probe response transmission for in-band discovery in 6GHz.
Changes include functions to store and retrieve probe response template,
and packet interval (0 - 20 TUs).
Setting interval to 0 disables the unsolicited broadcast probe response
transmission.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946b35-ad25858a-1f1f-48df-909e-dc7bf26d9169-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new attributes to support unsolicited broadcast
probe response transmission used for in-band
discovery in 6GHz band (IEEE P802.11ax/D6.0 26.17.2.3.2, AP behavior for
fast passive scanning).
The new attribute, NL80211_ATTR_UNSOL_BCAST_PROBE_RESP, is nested which
supports following parameters:
(1) NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT - Packet interval
(2) NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL - Template data
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946698-aac263ae-2ed3-4dab-9590-0bc7131214e1-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G channels have a single width defined per frequency, so
derive it from the channel flags with
ieee80211_s1g_channel_width().
Also support setting an S1G channel where control frequency may
differ from operating, and add some basic validation to
ensure the control channel is with the operating.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G supports 5 channel widths: 1, 2, 4, 8, and 16. One
channel width is allowed per frequency in each operating
class, so it makes more sense to advertise the specific
channel width allowed.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers using airtime fairness are calling ieee80211_sta_register_airtime
directly, now they must. Document this as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-8-nbd@nbd.name
[johannes: update the documentation to suit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value of struct bss_parameters::ap_isolate will be -1, 0 or 1.
The value -1 means not to change. To prevent developers from thinking
ap_isolate is only 0 or 1, I add more comments on it.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Reviewed-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908060157.98846-1-wright.feng@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not used since commit a09ceb0e08 ("sched: remove qdisc->drop")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the only listener of the nexthop notification chain is the
VXLAN driver. Subsequent patches will add more listeners (e.g., device
drivers such as netdevsim) that need to be able to block when processing
notifications.
Therefore, convert the notification chain to a blocking one. This is
safe as notifications are always emitted from process context.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not used anywhere.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not used or implemented anywhere.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a test command for health reporters. User might use this
command to trigger test event on a reporter if the reporter supports it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so the switchdev can notifiy the bridge to flush non-permanent fdb entries
for this port. This is useful whenever the hardware fdb of the switchdev
is reset, but the netdev and the bridgeport are not deleted.
Note that this has the same effect as the IFLA_BRPORT_FLUSH attribute.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Ivan Vecera <ivecera@redhat.com>
CC: Roopa Prabhu <roopa@nvidia.com>
CC: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So we'd better do the mask when set it in act_tunnel_key and cls_flower.
Otherwise, when users don't know these bits, they may configure with a
value which can never be matched.
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOCK_QUEUE_SHRUNK is currently used by TCP as a temporary state
that remembers if some room has been made in the rtx queue
by an incoming ACK packet.
This is later used from tcp_check_space() before
considering to send EPOLLOUT.
Problem is: If we receive SACK packets, and no packet
is removed from RTX queue, we can send fresh packets, thus
moving them from write queue to rtx queue and eventually
empty the write queue.
This stall can happen if TCP_NOTSENT_LOWAT is used.
With this fix, we no longer risk stalling sends while holes
are repaired, and we can fully use socket sndbuf.
This also removes a cache line dirtying for typical RPC
workloads.
Fixes: c9bee3b7fd ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That is needed to let the subflows announce promptly when new
space is available in the receive buffer.
tcp_cleanup_rbuf() is currently a static function, drop the
scope modifier and add a declaration in the TCP header.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emit controller suspend and resume events when we are ready for suspend
and we've resumed from suspend.
The controller suspend event will report whatever suspend state was
successfully entered. The controller resume event will check the first
HCI event that was received after we finished preparing for suspend and,
if it was a connection event, store the address of the peer that caused
the event. If it was not a connection event, we mark the wake reason as
an unexpected event.
Here is a sample btmon trace with these events:
@ MGMT Event: Controller Suspended (0x002d) plen 1
Suspend state: Page scanning and/or passive scanning (2)
@ MGMT Event: Controller Resumed (0x002e) plen 8
Wake reason: Remote wake due to peer device connection (2)
LE Address: CD:F3:CD:13:C5:9A (OUI CD-F3-CD)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the controller suspend and resume events, which will signal when
Bluetooth has completed preparing for suspend and when it's ready for
resume.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For new advertising features, it will be important for userspace to
know the capabilities of the controller and kernel. If the controller
and kernel support extended advertising, we include flags indicating
hardware offloading support and support for setting tx power of adv
instances.
In the future, vendor-specific commands may allow the setting of tx
power in advertising instances, but for now this feature is only
marked available if extended advertising is supported.
This change is manually verified in userspace by ensuring the
advertising manager's supported_flags field is updated with new flags on
hatch chromebook (ext advertising supported).
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the previous patches ensure that all call sites for
tcp_set_congestion_control() want to initialize congestion control, we
can simplify tcp_set_congestion_control() by removing the reinit
argument and the code to support it.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Kevin Yang <yyd@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Change tcp_init_transfer() to only initialize congestion control if it
has not been initialized already.
With this new approach, we can arrange things so that if the EBPF code
sets the congestion control by calling setsockopt(TCP_CONGESTION) then
tcp_init_transfer() will not re-initialize the CC module.
This is an approach that has the following beneficial properties:
(1) This allows CC module customizations made by the EBPF called in
tcp_init_transfer() to persist, and not be wiped out by a later
call to tcp_init_congestion_control() in tcp_init_transfer().
(2) Does not flip the order of EBPF and CC init, to avoid causing bugs
for existing code upstream that depends on the current order.
(3) Does not cause 2 initializations for for CC in the case where the
EBPF called in tcp_init_transfer() wants to set the CC to a new CC
algorithm.
(4) Allows follow-on simplifications to the code in net/core/filter.c
and net/ipv4/tcp_cong.c, which currently both have some complexity
to special-case CC initialization to avoid double CC
initialization if EBPF sets the CC.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Kevin Yang <yyd@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
There is no @validate argument.
CC: Johannes Berg <johannes.berg@intel.com>
Fixes: 3de6440354 ("netlink: re-add parse/validate functions in strict mode")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new TCP feature to reflect the tos value received in
SYN, and send it out on the SYN-ACK, and eventually set the tos value of
the established socket with this reflected tos value. This provides a
way to set the traffic class/QoS level for all traffic in the same
connection to be the same as the incoming SYN request. It could be
useful in data centers to provide equivalent QoS according to the
incoming request.
This feature is guarded by /proc/sys/net/ipv4/tcp_reflect_tos, and is by
default turned off.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds tos as a new passed in parameter to
ip_build_and_send_pkt() which will be used in the later commit.
This is a pure restructure and does not have any functional change.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A devlink port may be for a controller consist of PCI device.
A devlink instance holds ports of two types of controllers.
(1) controller discovered on same system where eswitch resides
This is the case where PCI PF/VF of a controller and devlink eswitch
instance both are located on a single system.
(2) controller located on external host system.
This is the case where a controller is located in one system and its
devlink eswitch ports are located in a different system.
When a devlink eswitch instance serves the devlink ports of both
controllers together, PCI PF/VF numbers may overlap.
Due to this a unique phys_port_name cannot be constructed.
For example in below such system controller-0 and controller-1, each has
PCI PF pf0 whose eswitch ports can be present in controller-0.
These results in phys_port_name as "pf0" for both.
Similar problem exists for VFs and upcoming Sub functions.
An example view of two controller systems:
---------------------------------------------------------
| |
| --------- --------- ------- ------- |
----------- | | vf(s) | | sf(s) | |vf(s)| |sf(s)| |
| server | | ------- ----/---- ---/----- ------- ---/--- ---/--- |
| pci rc |=== | pf0 |______/________/ | pf1 |___/_______/ |
| connect | | ------- ------- |
----------- | | controller_num=1 (no eswitch) |
------|--------------------------------------------------
(internal wire)
|
---------------------------------------------------------
| devlink eswitch ports and reps |
| ----------------------------------------------------- |
| |ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 |ctrl-0 | |
| |pf0 | pf0vfN | pf0sfN | pf1 | pf1vfN |pf1sfN | |
| ----------------------------------------------------- |
| |ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 |ctrl-1 | |
| |pf1 | pf1vfN | pf1sfN | pf1 | pf1vfN |pf0sfN | |
| ----------------------------------------------------- |
| |
| |
| --------- --------- ------- ------- |
| | vf(s) | | sf(s) | |vf(s)| |sf(s)| |
| ------- ----/---- ---/----- ------- ---/--- ---/--- |
| | pf0 |______/________/ | pf1 |___/_______/ |
| ------- ------- |
| |
| local controller_num=0 (eswitch) |
---------------------------------------------------------
An example devlink port for external controller with controller
number = 1 for a VF 1 of PF 0:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf controller 1 pfnum 0 vfnum 1 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port show pci/0000:06:00.0/2 -jp
{
"port": {
"pci/0000:06:00.0/2": {
"type": "eth",
"netdev": "ens2f0pf0vf1",
"flavour": "pcivf",
"controller": 1,
"pfnum": 0,
"vfnum": 1,
"external": true,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A devlink eswitch port may represent PCI PF/VF ports of a controller.
A controller either located on same system or it can be an external
controller located in host where such NIC is plugged in.
Add the ability for driver to specify if a port is for external
controller.
Use such flag in the mlx5_core driver.
An example of an external controller having VF1 of PF0 belong to
controller 1.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf pfnum 0 vfnum 1 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port show pci/0000:06:00.0/2 -jp
{
"port": {
"pci/0000:06:00.0/2": {
"type": "eth",
"netdev": "ens2f0pf0vf1",
"flavour": "pcivf",
"pfnum": 0,
"vfnum": 1,
"external": true,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To add more fields to the PCI PF and VF port attributes, follow standard
structure comment format.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comment block for physical, PF and VF port attributes.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Rewrite inner header IPv6 in ICMPv6 messages in ip6t_NPT,
from Michael Zhou.
2) do_ip_vs_set_ctl() dereferences uninitialized value,
from Peilin Ye.
3) Support for userdata in tables, from Jose M. Guisado.
4) Do not increment ct error and invalid stats at the same time,
from Florian Westphal.
5) Remove ct ignore stats, also from Florian.
6) Add ct stats for clash resolution, from Florian Westphal.
7) Bump reference counter bump on ct clash resolution only,
this is safe because bucket lock is held, again from Florian.
8) Use ip_is_fragment() in xt_HMARK, from YueHaibing.
9) Add wildcard support for nft_socket, from Balazs Scheidler.
10) Remove superfluous IPVS dependency on iptables, from
Yaroslav Bolyukin.
11) Remove unused definition in ebt_stp, from Wang Hai.
12) Replace CONFIG_NFT_CHAIN_NAT_{IPV4,IPV6} by CONFIG_NFT_NAT
in selftests/net, from Fabian Frederick.
13) Add userdata support for nft_object, from Jose M. Guisado.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables storing userdata for nft_object. Initially this will store an
optional comment but can be extended in the future as needed.
Adds new attribute NFTA_OBJ_USERDATA to nft_object.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On x86_64, each notification results in one skbuff allocation which
consumes at least 768 bytes due to the skbuff overhead.
This patch coalesces several notifications into one single skbuff, so
each notification consumes at least ~211 bytes, that ~3.5 times less
memory consumption. As a result, this is reducing the chances to exhaust
the netlink socket receive buffer.
Rule of thumb is that each notification batch only contains netlink
messages whose report flag is the same, nfnetlink_send() requires this
to do appropriate delivery to userspace, either via unicast (echo
mode) or multicast (monitor mode).
The skbuff control buffer is used to annotate the report flag for later
handling at the new coalescing routine.
The batch skbuff notification size is NLMSG_GOODSIZE, using a larger
skbuff would allow for more socket receiver buffer savings (to amortize
the cost of the skbuff even more), however, going over that size might
break userspace applications, so let's be conservative and stick to
NLMSG_GOODSIZE.
Reported-by: Phil Sutter <phil@nwl.cc>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
XFRMA_REPLAY_ESN_VAL was not cloned completely from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- move curleft cloning to a separate patch
Fixes: af2f464e32 ("xfrm: Assign esn pointers when cloning a state")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This dependency was added because ipv6_find_hdr was in iptables specific
code but is no longer required
Fixes: f8f626754e ("ipv6: Move ipv6_find_hdr() out of Netfilter code.")
Fixes: 63dca2c0b0 ("ipvs: Fix faulty IPv6 extension header handling in IPVS")
Signed-off-by: Yaroslav Bolyukin <iam@lach.pw>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The arg exact_dif is not used anymore, remove it. inet_exact_dif_match()
is no longer needed after the above is removed, so remove it too.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a pure codestyle cleanup patch. No functional change intended.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6_fragment to ipv6_stub to avoid calling netfilter when
access ip6_fragment.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to share a umem between queue ids on the same
device. This mode can be invoked with the XDP_SHARED_UMEM bind
flag. Previously, sharing was only supported within the same
queue id and device, and you shared one set of fill and
completion rings. However, note that when sharing a umem between
queue ids, you need to create a fill ring and a completion ring
and tie them to the socket before you do the bind with the
XDP_SHARED_UMEM flag. This so that the single-producer
single-consumer semantics can be upheld.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-12-git-send-email-magnus.karlsson@intel.com
Test for dma_need_sync earlier to increase
performance. xsk_buff_dma_sync_for_cpu() takes an xdp_buff as
parameter and from that the xsk_buff_pool reference is dug out. Perf
shows that this dereference causes a lot of cache misses. But as the
buffer pool is now sent down to the driver at zero-copy initialization
time, we might as well use this pointer directly, instead of going via
the xsk_buff and we can do so already in xsk_buff_dma_sync_for_cpu()
instead of in xp_dma_sync_for_cpu. This gets rid of these cache
misses.
Throughput increases with 3% for the xdpsock l2fwd sample application
on my machine.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-11-git-send-email-magnus.karlsson@intel.com
Rearrange the xdp_sock, xdp_umem and xsk_buff_pool structures so
that they get smaller and align better to the cache lines. In the
previous commits of this patch set, these structs have been
reordered with the focus on functionality and simplicity, not
performance. This patch improves throughput performance by around
3%.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-10-git-send-email-magnus.karlsson@intel.com
Enable the sharing of dma mappings by moving them out from the buffer
pool. Instead we put each dma mapped umem region in a list in the umem
structure. If dma has already been mapped for this umem and device, it
is not mapped again and the existing dma mappings are reused.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-9-git-send-email-magnus.karlsson@intel.com
Replicate the addrs pointer in the buffer pool to the umem. This mapping
will be the same for all buffer pools sharing the same umem. In the
buffer pool we leave the addrs pointer for performance reasons.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-8-git-send-email-magnus.karlsson@intel.com
Move the xsk_tx_list and the xsk_tx_list_lock from the umem to
the buffer pool. This so that we in a later commit can share the
umem between multiple HW queues. There is one xsk_tx_list per
device and queue id, so it should be located in the buffer pool.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-7-git-send-email-magnus.karlsson@intel.com
Move queue_id, dev, and need_wakeup from the umem to the
buffer pool. This so that we in a later commit can share the umem
between multiple HW queues. There is one buffer pool per dev and
queue id, so these variables should belong to the buffer pool, not
the umem. Need_wakeup is also something that is set on a per napi
level, so there is usually one per device and queue id. So move
this to the buffer pool too.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-6-git-send-email-magnus.karlsson@intel.com
Move the fill and completion rings from the umem to the buffer
pool. This so that we in a later commit can share the umem
between multiple HW queue ids. In this case, we need one fill and
completion ring per queue id. As the buffer pool is per queue id
and napi id this is a natural place for it and one umem
struture can be shared between these buffer pools.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-5-git-send-email-magnus.karlsson@intel.com
Create and free the buffer pool independently from the umem. Move
these operations that are performed on the buffer pool from the
umem create and destroy functions to new create and destroy
functions just for the buffer pool. This so that in later commits
we can instantiate multiple buffer pools per umem when sharing a
umem between HW queues and/or devices. We also erradicate the
back pointer from the umem to the buffer pool as this will not
work when we introduce the possibility to have multiple buffer
pools per umem.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-4-git-send-email-magnus.karlsson@intel.com
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Enables storing userdata for nft_table. Field udata points to user data
and udlen store its length.
Adds new attribute flag NFTA_TABLE_USERDATA
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----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=FWHJ
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200820' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc, afs: Fix probing issues
Here are some fixes for rxrpc and afs to fix issues in the RTT measuring in
rxrpc and thence the Volume Location server probing in afs:
(1) Move the serial number of a received ACK into a local variable to
simplify the next patch.
(2) Fix the loss of RTT samples due to extra interposed ACKs causing
baseline information to be discarded too early. This is a particular
problem for afs when it sends a single very short call to probe a
server it hasn't talked to recently.
(3) Fix rxrpc_kernel_get_srtt() to indicate whether it actually has seen
any valid samples or not.
(4) Remove a field that's set/woken, but never read/waited on.
(5) Expose the RTT and other probe information through procfs to make
debugging of this stuff easier.
(6) Fix VL rotation in afs to only use summary information from VL probing
and not the probe running state (which gets clobbered when next a
probe is issued).
(7) Fix VL rotation to actually return the error aggregated from the probe
errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the nl80211 structs, definitions, policies and parsing
code required to pass fixed HE rate, GI and LTF settings.
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200804081630.2013619-1-john@phrozen.org
[fix comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is no longer used, SCTP now uses a private helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for both bpf_{sk, inode}_storage_{get, delete} to be used
in LSM programs. These helpers are not used for tracing programs
(currently) as their usage is tied to the life-cycle of the object and
should only be used where the owning object won't be freed (when the
owning object is passed as an argument to the LSM hook). Thus, they
are safer to use in LSM hooks than tracing. Usage of local storage in
tracing programs will probably follow a per function based whitelist
approach.
Since the UAPI helper signature for bpf_sk_storage expect a bpf_sock,
it, leads to a compilation warning for LSM programs, it's also updated
to accept a void * pointer instead.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200825182919.1118197-7-kpsingh@chromium.org
Refactor the functionality in bpf_sk_storage.c so that concept of
storage linked to kernel objects can be extended to other objects like
inode, task_struct etc.
Each new local storage will still be a separate map and provide its own
set of helpers. This allows for future object specific extensions and
still share a lot of the underlying implementation.
This includes the changes suggested by Martin in:
https://lore.kernel.org/bpf/20200725013047.4006241-1-kafai@fb.com/
adding new map operations to support bpf_local_storage maps:
* storages for different kernel objects to optionally have different
memory charging strategy (map_local_storage_charge,
map_local_storage_uncharge)
* Functionality to extract the storage pointer from a pointer to the
owning object (map_owner_storage_ptr)
Co-developed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200825182919.1118197-4-kpsingh@chromium.org
A purely mechanical change to split the renaming from the actual
generalization.
Flags/consts:
SK_STORAGE_CREATE_FLAG_MASK BPF_LOCAL_STORAGE_CREATE_FLAG_MASK
BPF_SK_STORAGE_CACHE_SIZE BPF_LOCAL_STORAGE_CACHE_SIZE
MAX_VALUE_SIZE BPF_LOCAL_STORAGE_MAX_VALUE_SIZE
Structs:
bucket bpf_local_storage_map_bucket
bpf_sk_storage_map bpf_local_storage_map
bpf_sk_storage_data bpf_local_storage_data
bpf_sk_storage_elem bpf_local_storage_elem
bpf_sk_storage bpf_local_storage
The "sk" member in bpf_local_storage is also updated to "owner"
in preparation for changing the type to void * in a subsequent patch.
Functions:
selem_linked_to_sk selem_linked_to_storage
selem_alloc bpf_selem_alloc
__selem_unlink_sk bpf_selem_unlink_storage_nolock
__selem_link_sk bpf_selem_link_storage_nolock
selem_unlink_sk __bpf_selem_unlink_storage
sk_storage_update bpf_local_storage_update
__sk_storage_lookup bpf_local_storage_lookup
bpf_sk_storage_map_free bpf_local_storage_map_free
bpf_sk_storage_map_alloc bpf_local_storage_map_alloc
bpf_sk_storage_map_alloc_check bpf_local_storage_map_alloc_check
bpf_sk_storage_map_check_btf bpf_local_storage_map_check_btf
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200825182919.1118197-2-kpsingh@chromium.org
This patch is adapted from Eric's patch in an earlier discussion [1].
The TCP_SAVE_SYN currently only stores the network header and
tcp header. This patch allows it to optionally store
the mac header also if the setsockopt's optval is 2.
It requires one more bit for the "save_syn" bit field in tcp_sock.
This patch achieves this by moving the syn_smc bit next to the is_mptcp.
The syn_smc is currently used with the TCP experimental option. Since
syn_smc is only used when CONFIG_SMC is enabled, this patch also puts
the "IS_ENABLED(CONFIG_SMC)" around it like the is_mptcp did
with "IS_ENABLED(CONFIG_MPTCP)".
The mac_hdrlen is also stored in the "struct saved_syn"
to allow a quick offset from the bpf prog if it chooses to start
getting from the network header or the tcp header.
[1]: https://lore.kernel.org/netdev/CANn89iLJNWh6bkH7DNhy_kmcAexuUCccqERqe7z2QsvPhGrYPQ@mail.gmail.com/
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20200820190123.2886935-1-kafai@fb.com
[ Note: The TCP changes here is mainly to implement the bpf
pieces into the bpf_skops_*() functions introduced
in the earlier patches. ]
The earlier effort in BPF-TCP-CC allows the TCP Congestion Control
algorithm to be written in BPF. It opens up opportunities to allow
a faster turnaround time in testing/releasing new congestion control
ideas to production environment.
The same flexibility can be extended to writing TCP header option.
It is not uncommon that people want to test new TCP header option
to improve the TCP performance. Another use case is for data-center
that has a more controlled environment and has more flexibility in
putting header options for internal only use.
For example, we want to test the idea in putting maximum delay
ACK in TCP header option which is similar to a draft RFC proposal [1].
This patch introduces the necessary BPF API and use them in the
TCP stack to allow BPF_PROG_TYPE_SOCK_OPS program to parse
and write TCP header options. It currently supports most of
the TCP packet except RST.
Supported TCP header option:
───────────────────────────
This patch allows the bpf-prog to write any option kind.
Different bpf-progs can write its own option by calling the new helper
bpf_store_hdr_opt(). The helper will ensure there is no duplicated
option in the header.
By allowing bpf-prog to write any option kind, this gives a lot of
flexibility to the bpf-prog. Different bpf-prog can write its
own option kind. It could also allow the bpf-prog to support a
recently standardized option on an older kernel.
Sockops Callback Flags:
──────────────────────
The bpf program will only be called to parse/write tcp header option
if the following newly added callback flags are enabled
in tp->bpf_sock_ops_cb_flags:
BPF_SOCK_OPS_PARSE_UNKNOWN_HDR_OPT_CB_FLAG
BPF_SOCK_OPS_PARSE_ALL_HDR_OPT_CB_FLAG
BPF_SOCK_OPS_WRITE_HDR_OPT_CB_FLAG
A few words on the PARSE CB flags. When the above PARSE CB flags are
turned on, the bpf-prog will be called on packets received
at a sk that has at least reached the ESTABLISHED state.
The parsing of the SYN-SYNACK-ACK will be discussed in the
"3 Way HandShake" section.
The default is off for all of the above new CB flags, i.e. the bpf prog
will not be called to parse or write bpf hdr option. There are
details comment on these new cb flags in the UAPI bpf.h.
sock_ops->skb_data and bpf_load_hdr_opt()
─────────────────────────────────────────
sock_ops->skb_data and sock_ops->skb_data_end covers the whole
TCP header and its options. They are read only.
The new bpf_load_hdr_opt() helps to read a particular option "kind"
from the skb_data.
Please refer to the comment in UAPI bpf.h. It has details
on what skb_data contains under different sock_ops->op.
3 Way HandShake
───────────────
The bpf-prog can learn if it is sending SYN or SYNACK by reading the
sock_ops->skb_tcp_flags.
* Passive side
When writing SYNACK (i.e. sock_ops->op == BPF_SOCK_OPS_WRITE_HDR_OPT_CB),
the received SYN skb will be available to the bpf prog. The bpf prog can
use the SYN skb (which may carry the header option sent from the remote bpf
prog) to decide what bpf header option should be written to the outgoing
SYNACK skb. The SYN packet can be obtained by getsockopt(TCP_BPF_SYN*).
More on this later. Also, the bpf prog can learn if it is in syncookie
mode (by checking sock_ops->args[0] == BPF_WRITE_HDR_TCP_SYNACK_COOKIE).
The bpf prog can store the received SYN pkt by using the existing
bpf_setsockopt(TCP_SAVE_SYN). The example in a later patch does it.
[ Note that the fullsock here is a listen sk, bpf_sk_storage
is not very useful here since the listen sk will be shared
by many concurrent connection requests.
Extending bpf_sk_storage support to request_sock will add weight
to the minisock and it is not necessary better than storing the
whole ~100 bytes SYN pkt. ]
When the connection is established, the bpf prog will be called
in the existing PASSIVE_ESTABLISHED_CB callback. At that time,
the bpf prog can get the header option from the saved syn and
then apply the needed operation to the newly established socket.
The later patch will use the max delay ack specified in the SYN
header and set the RTO of this newly established connection
as an example.
The received ACK (that concludes the 3WHS) will also be available to
the bpf prog during PASSIVE_ESTABLISHED_CB through the sock_ops->skb_data.
It could be useful in syncookie scenario. More on this later.
There is an existing getsockopt "TCP_SAVED_SYN" to return the whole
saved syn pkt which includes the IP[46] header and the TCP header.
A few "TCP_BPF_SYN*" getsockopt has been added to allow specifying where to
start getting from, e.g. starting from TCP header, or from IP[46] header.
The new getsockopt(TCP_BPF_SYN*) will also know where it can get
the SYN's packet from:
- (a) the just received syn (available when the bpf prog is writing SYNACK)
and it is the only way to get SYN during syncookie mode.
or
- (b) the saved syn (available in PASSIVE_ESTABLISHED_CB and also other
existing CB).
The bpf prog does not need to know where the SYN pkt is coming from.
The getsockopt(TCP_BPF_SYN*) will hide this details.
Similarly, a flags "BPF_LOAD_HDR_OPT_TCP_SYN" is also added to
bpf_load_hdr_opt() to read a particular header option from the SYN packet.
* Fastopen
Fastopen should work the same as the regular non fastopen case.
This is a test in a later patch.
* Syncookie
For syncookie, the later example patch asks the active
side's bpf prog to resend the header options in ACK. The server
can use bpf_load_hdr_opt() to look at the options in this
received ACK during PASSIVE_ESTABLISHED_CB.
* Active side
The bpf prog will get a chance to write the bpf header option
in the SYN packet during WRITE_HDR_OPT_CB. The received SYNACK
pkt will also be available to the bpf prog during the existing
ACTIVE_ESTABLISHED_CB callback through the sock_ops->skb_data
and bpf_load_hdr_opt().
* Turn off header CB flags after 3WHS
If the bpf prog does not need to write/parse header options
beyond the 3WHS, the bpf prog can clear the bpf_sock_ops_cb_flags
to avoid being called for header options.
Or the bpf-prog can select to leave the UNKNOWN_HDR_OPT_CB_FLAG on
so that the kernel will only call it when there is option that
the kernel cannot handle.
[1]: draft-wang-tcpm-low-latency-opt-00
https://tools.ietf.org/html/draft-wang-tcpm-low-latency-opt-00
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200820190104.2885895-1-kafai@fb.com
The bpf prog needs to parse the SYN header to learn what options have
been sent by the peer's bpf-prog before writing its options into SYNACK.
This patch adds a "syn_skb" arg to tcp_make_synack() and send_synack().
This syn_skb will eventually be made available (as read-only) to the
bpf prog. This will be the only SYN packet available to the bpf
prog during syncookie. For other regular cases, the bpf prog can
also use the saved_syn.
When writing options, the bpf prog will first be called to tell the
kernel its required number of bytes. It is done by the new
bpf_skops_hdr_opt_len(). The bpf prog will only be called when the new
BPF_SOCK_OPS_WRITE_HDR_OPT_CB_FLAG is set in tp->bpf_sock_ops_cb_flags.
When the bpf prog returns, the kernel will know how many bytes are needed
and then update the "*remaining" arg accordingly. 4 byte alignment will
be included in the "*remaining" before this function returns. The 4 byte
aligned number of bytes will also be stored into the opts->bpf_opt_len.
"bpf_opt_len" is a newly added member to the struct tcp_out_options.
Then the new bpf_skops_write_hdr_opt() will call the bpf prog to write the
header options. The bpf prog is only called if it has reserved spaces
before (opts->bpf_opt_len > 0).
The bpf prog is the last one getting a chance to reserve header space
and writing the header option.
These two functions are half implemented to highlight the changes in
TCP stack. The actual codes preparing the bpf running context and
invoking the bpf prog will be added in the later patch with other
necessary bpf pieces.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20200820190052.2885316-1-kafai@fb.com
In tcp_init_transfer(), it currently calls the bpf prog to give it a
chance to handle the just "ESTABLISHED" event (e.g. do setsockopt
on the newly established sk). Right now, it is done by calling the
general purpose tcp_call_bpf().
In the later patch, it also needs to pass the just-received skb which
concludes the 3 way handshake. E.g. the SYNACK received at the active side.
The bpf prog can then learn some specific header options written by the
peer's bpf-prog and potentially do setsockopt on the newly established sk.
Thus, instead of reusing the general purpose tcp_call_bpf(), a new function
bpf_skops_established() is added to allow passing the "skb" to the bpf
prog. The actual skb passing from bpf_skops_established() to the bpf prog
will happen together in a later patch which has the necessary bpf pieces.
A "skb" arg is also added to tcp_init_transfer() such that
it can then be passed to bpf_skops_established().
Calling the new bpf_skops_established() instead of tcp_call_bpf()
should be a noop in this patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190039.2884750-1-kafai@fb.com
This patch adds bpf_setsockopt(TCP_BPF_RTO_MIN) to allow bpf prog
to set the min rto of a connection. It could be used together
with the earlier patch which has added bpf_setsockopt(TCP_BPF_DELACK_MAX).
A later selftest patch will communicate the max delay ack in a
bpf tcp header option and then the receiving side can use
bpf_setsockopt(TCP_BPF_RTO_MIN) to set a shorter rto.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190027.2884170-1-kafai@fb.com
This change is mostly from an internal patch and adapts it from sysctl
config to the bpf_setsockopt setup.
The bpf_prog can set the max delay ack by using
bpf_setsockopt(TCP_BPF_DELACK_MAX). This max delay ack can be communicated
to its peer through bpf header option. The receiving peer can then use
this max delay ack and set a potentially lower rto by using
bpf_setsockopt(TCP_BPF_RTO_MIN) which will be introduced
in the next patch.
Another later selftest patch will also use it like the above to show
how to write and parse bpf tcp header option.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190021.2884000-1-kafai@fb.com
The TCP_SAVE_SYN has both the network header and tcp header.
The total length of the saved syn packet is currently stored in
the first 4 bytes (u32) of an array and the actual packet data is
stored after that.
A later patch will add a bpf helper that allows to get the tcp header
alone from the saved syn without the network header. It will be more
convenient to have a direct offset to a specific header instead of
re-parsing it. This requires to separately store the network hdrlen.
The total header length (i.e. network + tcp) is still needed for the
current usage in getsockopt. Although this total length can be obtained
by looking into the tcphdr and then get the (th->doff << 2), this patch
chooses to directly store the tcp hdrlen in the second four bytes of
this newly created "struct saved_syn". By using a new struct, it can
give a readable name to each individual header length.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200820190014.2883694-1-kafai@fb.com
Commit 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
changed ndisc_ifinfo_sysctl_change to take a kernel pointer. Adjust its
prototype in net/ndisc.h as well to fix the following sparse warning:
net/ipv6/ndisc.c:1838:5: error: symbol 'ndisc_ifinfo_sysctl_change' redeclared with different type (incompatible argument 3 (different address spaces)):
net/ipv6/ndisc.c:1838:5: int extern [addressable] [signed] [toplevel] ndisc_ifinfo_sysctl_change( ... )
net/ipv6/ndisc.c: note: in included file (through include/net/ipv6.h):
./include/net/ndisc.h:496:5: note: previously declared as:
./include/net/ndisc.h:496:5: int extern [addressable] [signed] [toplevel] ndisc_ifinfo_sysctl_change( ... )
net/ipv6/ndisc.c: note: in included file (through include/net/ip6_route.h):
Fixes: 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following bug was reported via irc:
nft list ruleset
set knock_candidates_ipv4 {
type ipv4_addr . inet_service
size 65535
elements = { 127.0.0.1 . 123,
127.0.0.1 . 123 }
}
..
udp dport 123 add @knock_candidates_ipv4 { ip saddr . 123 }
udp dport 123 add @knock_candidates_ipv4 { ip saddr . udp dport }
It should not have been possible to add a duplicate set entry.
After some debugging it turned out that the problem is the immediate
value (123) in the second-to-last rule.
Concatenations use 32bit registers, i.e. the elements are 8 bytes each,
not 6 and it turns out the kernel inserted
inet firewall @knock_candidates_ipv4
element 0100007f ffff7b00 : 0 [end]
element 0100007f 00007b00 : 0 [end]
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All callers of these primitives will
* discard anything we might've copied in case of error
* ignore the csum value in case of error
* always pass 0xffffffff as the initial sum, so the
resulting csum value (in case of success, that is) will never be 0.
That suggest the following calling conventions:
* don't pass err_ptr - just return 0 on error.
* don't bother with zeroing destination, etc. in case of error
* don't pass the initial sum - just use 0xffffffff.
This commit does the minimal conversion in the instances of csum_and_copy_...();
the changes of actual asm code behind them are done later in the series.
Note that this asm code is often shared with csum_partial_copy_nocheck();
the difference is that csum_partial_copy_nocheck() passes 0 for initial
sum while csum_and_copy_..._user() pass 0xffffffff. Fortunately, we are
free to pass 0xffffffff in all cases and subsequent patches will use that
freedom without any special comments.
A part that could be split off: parisc and uml/i386 claimed to have
csum_and_copy_to_user() instances of their own, but those were identical
to the generic one, so we simply drop them. Not sure if it's worth
a separate commit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's always 0. Note that we theoretically could use ~0U as well -
result will be the same modulo 0xffff, _if_ the damn thing did the
right thing for any value of initial sum; later we'll make use of
that when convenient.
However, unlike csum_and_copy_..._user(), there are instances that
did not work for arbitrary initial sums; c6x is one such.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
quite a few architectures have the same csum_partial_copy_nocheck() -
simply memcpy() the data and then return the csum of the copy.
hexagon, parisc, ia64, s390, um: explicitly spelled out that way.
arc, arm64, csky, h8300, m68k/nommu, microblaze, mips/GENERIC_CSUM, nds32,
nios2, openrisc, riscv, unicore32: end up picking the same thing spelled
out in lib/checksum.h (with varying amounts of perversions along the way).
everybody else (alpha, arm, c6x, m68k/mmu, mips/!GENERIC_CSUM, powerpc,
sh, sparc, x86, xtensa) have non-generic variants. For all except c6x
the declaration is in their asm/checksum.h. c6x uses the wrapper
from asm-generic/checksum.h that would normally lead to the lib/checksum.h
instance, but in case of c6x we end up using an asm function from arch/c6x
instead.
Screw that mess - have architectures with private instances define
_HAVE_ARCH_CSUM_AND_COPY in their asm/checksum.h and have the default
one right in net/checksum.h conditional on _HAVE_ARCH_CSUM_AND_COPY
*not* defined.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix rxrpc_kernel_get_srtt() to indicate the validity of the returned
smoothed RTT. If we haven't had any valid samples yet, the SRTT isn't
useful.
Fixes: c410bf0193 ("rxrpc: Fix the excessive initial retransmission timeout")
Signed-off-by: David Howells <dhowells@redhat.com>
Switch over network namespaces to use the newly introduced common lifetime
counter.
Network namespaces have an additional counter named "passive". This counter
does not guarantee that the network namespace is not already de-initialized
and so isn't concerned with the actual lifetime of the network namespace;
only the "count" counter is. So the latter is moved into struct ns_common.
Currently every namespace type has its own lifetime counter which is stored
in the specific namespace struct. The lifetime counters are used
identically for all namespaces types. Namespaces may of course have
additional unrelated counters and these are not altered.
This introduces a common lifetime counter into struct ns_common. The
ns_common struct encompasses information that all namespaces share. That
should include the lifetime counter since its common for all of them.
It also allows us to unify the type of the counters across all namespaces.
Most of them use refcount_t but one uses atomic_t and at least one uses
kref. Especially the last one doesn't make much sense since it's just a
wrapper around refcount_t since 2016 and actually complicates cleanup
operations by having to use container_of() to cast the correct namespace
struct out of struct ns_common.
Having the lifetime counter for the namespaces in one place reduces
maintenance cost. Not just because after switching all namespaces over we
will have removed more code than we added but also because the logic is
more easily understandable and we indicate to the user that the basic
lifetime requirements for all namespaces are currently identical.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
[christian.brauner@ubuntu.com: rewrite commit]
Link: https://lore.kernel.org/r/159644977635.604812.1319877322927063560.stgit@localhost.localdomain
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
This patch is to do 3 things for ipv6_dev_find():
As David A. noticed,
- rt6_lookup() is not really needed. Different from __ip_dev_find(),
ipv6_dev_find() doesn't have a compatibility problem, so remove it.
As Hideaki suggested,
- "valid" (non-tentative) check for the address is also needed.
ipv6_chk_addr() calls ipv6_chk_addr_and_flags(), which will
traverse the address hash list, but it's heavy to be called
inside ipv6_dev_find(). This patch is to reuse the code of
ipv6_chk_addr_and_flags() for ipv6_dev_find().
- dev parameter is passed into ipv6_dev_find(), as link-local
addresses from user space has sin6_scope_id set and the dev
lookup needs it.
Fixes: 81f6cb3122 ("ipv6: add ipv6_dev_find()")
Suggested-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add range validation for NLA_BINARY, allowing validation of any
combination of combination minimum or maximum lengths, using the
existing NLA_POLICY_RANGE()/NLA_POLICY_FULL_RANGE() macros, just
like for integers where the value is checked.
Also make NLA_POLICY_EXACT_LEN(), NLA_POLICY_EXACT_LEN_WARN()
and NLA_POLICY_MIN_LEN() special cases of this, removing the old
types NLA_EXACT_LEN and NLA_MIN_LEN.
This allows us to save some code where both minimum and maximum
lengths are requires, currently the policy only allows maximum
(NLA_BINARY), minimum (NLA_MIN_LEN) or exact (NLA_EXACT_LEN), so
a range of lengths cannot be accepted and must be checked by the
code that consumes the attributes later.
Also, this allows advertising the correct ranges in the policy
export to userspace. Here, NLA_MIN_LEN and NLA_EXACT_LEN already
were special cases of NLA_BINARY with min and min/max length
respectively.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Some merge window fallout, some longer term fixes:
1) Handle headroom properly in lapbether and x25_asy drivers, from
Xie He.
2) Fetch MAC address from correct r8152 device node, from Thierry
Reding.
3) In the sw kTLS path we should allow MSG_CMSG_COMPAT in sendmsg,
from Rouven Czerwinski.
4) Correct fdputs in socket layer, from Miaohe Lin.
5) Revert troublesome sockptr_t optimization, from Christoph Hellwig.
6) Fix TCP TFO key reading on big endian, from Jason Baron.
7) Missing CAP_NET_RAW check in nfc, from Qingyu Li.
8) Fix inet fastreuse optimization with tproxy sockets, from Tim
Froidcoeur.
9) Fix 64-bit divide in new SFC driver, from Edward Cree.
10) Add a tracepoint for prandom_u32 so that we can more easily
perform usage analysis. From Eric Dumazet.
11) Fix rwlock imbalance in AF_PACKET, from John Ogness"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
net: openvswitch: introduce common code for flushing flows
af_packet: TPACKET_V3: fix fill status rwlock imbalance
random32: add a tracepoint for prandom_u32()
Revert "ipv4: tunnel: fix compilation on ARCH=um"
net: accept an empty mask in /sys/class/net/*/queues/rx-*/rps_cpus
net: ethernet: stmmac: Disable hardware multicast filter
net: stmmac: dwmac1000: provide multicast filter fallback
ipv4: tunnel: fix compilation on ARCH=um
vsock: fix potential null pointer dereference in vsock_poll()
sfc: fix ef100 design-param checking
net: initialize fastreuse on inet_inherit_port
net: refactor bind_bucket fastreuse into helper
net: phy: marvell10g: fix null pointer dereference
net: Fix potential memory leak in proto_register()
net: qcom/emac: add missed clk_disable_unprepare in error path of emac_clks_phase1_init
ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()
net/nfc/rawsock.c: add CAP_NET_RAW check.
hinic: fix strncpy output truncated compile warnings
drivers/net/wan/x25_asy: Added needed_headroom and a skb->len check
net/tls: Fix kmap usage
...
Refactor the fastreuse update code in inet_csk_get_port into a small
helper function that can be called from other places.
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Untangle the header spaghetti which causes build failures in various
situations caused by the lockdep additions to seqcount to validate that
the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict per
CPU seqcounts. As the lock is not part of the seqcount, lockdep cannot
validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored and
write_seqcount_begin() has a lockdep assertion to validate that the
lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API is
unchanged and determines the type at compile time with the help of
_Generic which is possible now that the minimal GCC version has been
moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs which
have been addressed already independent of this.
While generaly useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if the
writers are serialized by an associated lock, which leads to the well
known reader preempts writer livelock. RT prevents this by storing the
associated lock pointer independent of lockdep in the seqcount and
changing the reader side to block on the lock when a reader detects
that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and initializers.
-----BEGIN PGP SIGNATURE-----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=7Gj+
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
"A set of locking fixes and updates:
- Untangle the header spaghetti which causes build failures in
various situations caused by the lockdep additions to seqcount to
validate that the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict
per CPU seqcounts. As the lock is not part of the seqcount, lockdep
cannot validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored
and write_seqcount_begin() has a lockdep assertion to validate that
the lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API
is unchanged and determines the type at compile time with the help
of _Generic which is possible now that the minimal GCC version has
been moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs
which have been addressed already independent of this.
While generally useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if
the writers are serialized by an associated lock, which leads to
the well known reader preempts writer livelock. RT prevents this by
storing the associated lock pointer independent of lockdep in the
seqcount and changing the reader side to block on the lock when a
reader detects that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and
initializers"
* tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/seqlock, headers: Untangle the spaghetti monster
locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header
x86/headers: Remove APIC headers from <asm/smp.h>
seqcount: More consistent seqprop names
seqcount: Compress SEQCNT_LOCKNAME_ZERO()
seqlock: Fold seqcount_LOCKNAME_init() definition
seqlock: Fold seqcount_LOCKNAME_t definition
seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g
hrtimer: Use sequence counter with associated raw spinlock
kvm/eventfd: Use sequence counter with associated spinlock
userfaultfd: Use sequence counter with associated spinlock
NFSv4: Use sequence counter with associated spinlock
iocost: Use sequence counter with associated spinlock
raid5: Use sequence counter with associated spinlock
vfs: Use sequence counter with associated spinlock
timekeeping: Use sequence counter with associated raw spinlock
xfrm: policy: Use sequence counters with associated lock
netfilter: nft_set_rbtree: Use sequence counter with associated rwlock
netfilter: conntrack: Use sequence counter with associated spinlock
sched: tasks: Use sequence counter with associated spinlock
...
When TFO keys are read back on big endian systems either via the global
sysctl interface or via getsockopt() using TCP_FASTOPEN_KEY, the values
don't match what was written.
For example, on s390x:
# echo "1-2-3-4" > /proc/sys/net/ipv4/tcp_fastopen_key
# cat /proc/sys/net/ipv4/tcp_fastopen_key
02000000-01000000-04000000-03000000
Instead of:
# cat /proc/sys/net/ipv4/tcp_fastopen_key
00000001-00000002-00000003-00000004
Fix this by converting to the correct endianness on read. This was
reported by Colin Ian King when running the 'tcp_fastopen_backup_key' net
selftest on s390x, which depends on the read value matching what was
written. I've confirmed that the test now passes on big and little endian
systems.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Fixes: 438ac88009 ("net: fastopen: robustness and endianness fixes for SipHash")
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Eric Dumazet <edumazet@google.com>
Reported-and-tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set includes a some improvements to the dlm
networking layer: improving the ability to trace
dlm messages for debugging, and improved handling
of bad messages or disrupted connections.
-----BEGIN PGP SIGNATURE-----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=qgti
-----END PGP SIGNATURE-----
Merge tag 'dlm-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set includes a some improvements to the dlm networking layer:
improving the ability to trace dlm messages for debugging, and
improved handling of bad messages or disrupted connections"
* tag 'dlm-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
fs: dlm: implement tcp graceful shutdown
fs: dlm: change handling of reconnects
fs: dlm: don't close socket on invalid message
fs: dlm: set skb mark per peer socket
fs: dlm: set skb mark for listen socket
net: sock: add sock_set_mark
dlm: Fix kobject memleak
This patch adds a new socket helper function to set the mark value for a
kernel socket.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
This is to add an ip_dev_find like function for ipv6, used to find
the dev by saddr.
It will be used by TIPC protocol. So also export it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Improved selftest coverage, timeouts, and reporting
- Add EPOLLHUP support for SECCOMP_RET_USER_NOTIF (Christian Brauner)
- Refactor __scm_install_fd() into __receive_fd() and fix buggy callers
- Introduce "addfd" command for SECCOMP_RET_USER_NOTIF (Sargun Dhillon)
-----BEGIN PGP SIGNATURE-----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=yb55
-----END PGP SIGNATURE-----
Merge tag 'seccomp-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"There are a bunch of clean ups and selftest improvements along with
two major updates to the SECCOMP_RET_USER_NOTIF filter return:
EPOLLHUP support to more easily detect the death of a monitored
process, and being able to inject fds when intercepting syscalls that
expect an fd-opening side-effect (needed by both container folks and
Chrome). The latter continued the refactoring of __scm_install_fd()
started by Christoph, and in the process found and fixed a handful of
bugs in various callers.
- Improved selftest coverage, timeouts, and reporting
- Add EPOLLHUP support for SECCOMP_RET_USER_NOTIF (Christian Brauner)
- Refactor __scm_install_fd() into __receive_fd() and fix buggy
callers
- Introduce 'addfd' command for SECCOMP_RET_USER_NOTIF (Sargun
Dhillon)"
* tag 'seccomp-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
selftests/seccomp: Test SECCOMP_IOCTL_NOTIF_ADDFD
seccomp: Introduce addfd ioctl to seccomp user notifier
fs: Expand __receive_fd() to accept existing fd
pidfd: Replace open-coded receive_fd()
fs: Add receive_fd() wrapper for __receive_fd()
fs: Move __scm_install_fd() to __receive_fd()
net/scm: Regularize compat handling of scm_detach_fds()
pidfd: Add missing sock updates for pidfd_getfd()
net/compat: Add missing sock updates for SCM_RIGHTS
selftests/seccomp: Check ENOSYS under tracing
selftests/seccomp: Refactor to use fixture variants
selftests/harness: Clean up kern-doc for fixtures
seccomp: Use -1 marker for end of mode 1 syscall list
seccomp: Fix ioctl number for SECCOMP_IOCTL_NOTIF_ID_VALID
selftests/seccomp: Rename user_trap_syscall() to user_notif_syscall()
selftests/seccomp: Make kcmp() less required
seccomp: Use pr_fmt
selftests/seccomp: Improve calibration loop
selftests/seccomp: use 90s as timeout
selftests/seccomp: Expand benchmark to per-filter measurements
...
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Flush the cleanup xtables worker to make sure destructors
have completed, from Florian Westphal.
2) iifgroup is matching erroneously, also from Florian.
3) Add selftest for meta interface matching, from Florian Westphal.
4) Move nf_ct_offload_timeout() to header, from Roi Dayan.
5) Call nf_ct_offload_timeout() from flow_offload_add() to
make sure garbage collection does not evict offloaded flow,
from Roi Dayan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.
PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.
On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:
VTEPs MUST NOT fragment VXLAN packets. Intermediate routers may
fragment encapsulated VXLAN packets due to the larger frame size.
The destination VTEP MAY silently discard such VXLAN fragments.
The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.
Further, it states that:
Other techniques like Path MTU discovery (see [RFC1191] and
[RFC1981]) MAY be used to address this requirement as well.
Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.
Add the missing bits for bridged cases:
- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
RFC 4443 section 2.4 for ICMPv6. This function is already called by
UDP tunnels
- a new function generating those ICMP or ICMPv6 replies. We can't
reuse icmp_send() and icmp6_send() as we don't see the sender as a
valid destination. This doesn't need to be generic, as we don't
cover any other type of ICMP errors given that we only provide an
encapsulation function to the sender
While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).
This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.
v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch will refuse to set the action of certain traps in mlxsw
and also to change the policer binding of certain groups. Pass extack so
that failure could be communicated clearly to user space.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the packet trap that can report packets that were ECN marked due to RED
AQM.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) UAF in chain binding support from previous batch, from Dan Carpenter.
2) Queue up delayed work to expire connections with no destination,
from Andrew Sy Kim.
3) Use fallthrough pseudo-keyword, from Gustavo A. R. Silva.
4) Replace HTTP links with HTTPS, from Alexander A. Klimov.
5) Remove superfluous null header checks in ip6tables, from
Gaurav Singh.
6) Add extended netlink error reporting for expression.
7) Report EEXIST on overlapping chain, set elements and flowtable
devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When openvswitch conntrack offload with act_ct action. Fragment packets
defrag in the ingress tc act_ct action and miss the next chain. Then the
packet pass to the openvswitch datapath without the mru. The over
mtu packet will be dropped in output action in openvswitch for over mtu.
"kernel: net2: dropped over-mtu packet: 1528 > 1500"
This patch add mru in the tc_skb_ext for adefrag and miss next chain
situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru
to the qdisc_skb_cb when the packet defrag. And When the chain miss,
The mru is set to tc_skb_ext which can be got by ovs datapath.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To be used by callers from other modules.
[ Rename DAY to NF_CT_DAY to avoid possible symbol name pollution
issue --Pablo ]
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
-----BEGIN PGP SIGNATURE-----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=FR6T
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-07-31
1) Fix policy matching with mark and mask on userspace interfaces.
From Xin Long.
2) Several fixes for the new ESP in TCP encapsulation.
From Sabrina Dubroca.
3) Fix crash when the hold queue is used. The assumption that
xdst->path and dst->child are not a NULL pointer only if dst->xfrm
is not a NULL pointer is true with the exception of using the
hold queue. Fix this by checking for hold queue usage before
dereferencing xdst->path or dst->child.
4) Validate pfkey_dump parameter before sending them.
From Mark Salyzyn.
5) Fix the location of the transport header with ESP in UDPv6
encapsulation. From Sabrina Dubroca.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If SYN packet contains MP_CAPABLE option, keep it enabled.
Syncokie validation and cookie-based socket creation is changed to
instantiate an mptcp request sockets if the ACK contains an MPTCP
connection request.
Rather than extend both cookie_v4/6_check, add a common helper to create
the (mp)tcp request socket.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to initialize the mptcp request socket when a MP_CAPABLE
request was handled in syncookie mode, i.e. when a TCP ACK containing a
MP_CAPABLE option is a valid syncookie value.
Normally (non-cookie case), MPTCP will generate a unique 32 bit connection
ID and stores it in the MPTCP token storage to be able to retrieve the
mptcp socket for subflow joining.
In syncookie case, we do not want to store any state, so just generate the
unique ID and use it in the reply.
This means there is a small window where another connection could generate
the same token.
When Cookie ACK comes back, we check that the token has not been registered
in the mean time. If it was, the connection needs to fall back to TCP.
Changes in v2:
- use req->syncookie instead of passing 'want_cookie' arg to ->init_req()
(Eric Dumazet)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syncookie code path needs to create an mptcp request sock.
Prepare for this and add mptcp prefix plus needed export of ops struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nowadays output function has a 'synack_type' argument that tells us when
the syn/ack is emitted via syncookies.
The request already tells us when timestamps are supported, so check
both to detect special timestamp for tcp option encoding is needed.
We could remove cookie_ts altogether, but a followup patch would
otherwise need to adjust function signatures to pass 'want_cookie' to
mptcp core.
This way, the 'existing' bit can be used.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira found that after recent update of xt_IDLETIMER the
iptables-nft tests sometimes show an error.
He tracked this down to the delayed cleanup used by nf_tables core:
del rule (transaction A)
add rule (transaction B)
Its possible that by time transaction B (both in same netns) runs,
the xt target destructor has not been invoked yet.
For native nft expressions this is no problem because all expressions
that have such side effects make sure these are handled from the commit
phase, rather than async cleanup.
For nft_compat however this isn't true.
Instead of forcing synchronous behaviour for nft_compat, keep track
of the number of outstanding destructor calls.
When we attempt to create a new expression, flush the cleanup worker
to make sure destructors have completed.
With lots of help from Pablo Neira.
Reported-by: Pablo Neira Ayso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to run mac80211 rx processing on a batch of frames in NAPI
poll before passing them to the network stack in a large batch.
This can improve icache footprint, or it can be used to pass frames via
netif_receive_skb_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200726110611.46886-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Already parse the radiotap header in ieee80211_monitor_select_queue.
In a subsequent commit this will allow us to add a radiotap flag that
influences the queue on which injected packets will be sent.
This also fixes the incomplete validation of the injected frame in
ieee80211_monitor_select_queue: currently an out of bounds memory
access may occur in in the called function ieee80211_select_queue_80211
if the 802.11 header is too small.
Note that in ieee80211_monitor_start_xmit the radiotap header is parsed
again, which is necessairy because ieee80211_monitor_select_queue is not
always called beforehand.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-6-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IPV6_ADDRFORM causes resource leaks when converting an IPv6 socket
to IPv4, particularly struct ipv6_ac_socklist. Similar to
struct ipv6_mc_socklist, we should just close it on this path.
This bug can be easily reproduced with the following C program:
#include <stdio.h>
#include <string.h>
#include <sys/types.h>
#include <sys/socket.h>
#include <arpa/inet.h>
int main()
{
int s, value;
struct sockaddr_in6 addr;
struct ipv6_mreq m6;
s = socket(AF_INET6, SOCK_DGRAM, 0);
addr.sin6_family = AF_INET6;
addr.sin6_port = htons(5000);
inet_pton(AF_INET6, "::ffff:192.168.122.194", &addr.sin6_addr);
connect(s, (struct sockaddr *)&addr, sizeof(addr));
inet_pton(AF_INET6, "fe80::AAAA", &m6.ipv6mr_multiaddr);
m6.ipv6mr_interface = 5;
setsockopt(s, SOL_IPV6, IPV6_JOIN_ANYCAST, &m6, sizeof(m6));
value = AF_INET;
setsockopt(s, SOL_IPV6, IPV6_ADDRFORM, &value, sizeof(value));
close(s);
return 0;
}
Reported-by: ch3332xr@gmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-07-30
Please note that I did the first time now --no-ff merges
of my testing branch into the master branch to include
the [PATCH 0/n] message of a patchset. Please let me
know if this is desirable, or if I should do it any
different.
1) Introduce a oseq-may-wrap flag to disable anti-replay
protection for manually distributed ICVs as suggested
in RFC 4303. From Petr Vaněk.
2) Patchset to fully support IPCOMP for vti4, vti6 and
xfrm interfaces. From Xin Long.
3) Switch from a linear list to a hash list for xfrm interface
lookups. From Eyal Birger.
4) Fixes to not register one xfrm(6)_tunnel object twice.
From Xin Long.
5) Fix two compile errors that were introduced with the
IPCOMP support for vti and xfrm interfaces.
Also from Xin Long.
6) Make the policy hold queue work with VTI. This was
forgotten when VTI was implemented.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LL Privacy support is available, then as part of enabling or
disabling passive background scanning, it is required to set up the
controller based address resolution as well.
Since only passive background scanning is utilizing the whitelist, the
address resolution is now bound to the whitelist and passive background
scanning. All other resolution can be easily done by the host stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A sequence counter write side critical section must be protected by some
form of locking to serialize writers. A plain seqcount_t does not
contain the information of which lock must be held when entering a write
side critical section.
Use the new seqcount_spinlock_t data type, which allows to associate a
spinlock with the sequence counter. This enables lockdep to verify that
the spinlock used for writer serialization is held when the write side
critical section is entered.
If lockdep is disabled this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200720155530.1173732-15-a.darwish@linutronix.de
This avoids another inderect call per RX packet which save us around
20-40 ns.
Changelog:
v1 -> v2:
- Move declaraions to fib_rules.h to remove warnings
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Note that the get case is pretty weird in that it actually copies data
back to userspace from setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreive a hash value from the SKB and store it
in the dissector key for future matching.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that touching linux/rhashtable.h causes lib/vsprintf.c to
be rebuilt. This dependency came through a bogus inclusion in the
file net/flow_offload.h. This patch moves it to the right place.
This patch also removes a lingering rhashtable inclusion in cls_api
created by the same commit.
Fixes: 4e481908c5 ("flow_offload: move tc indirect block to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 46 non-merge commits during the last 6 day(s) which contain
a total of 68 files changed, 4929 insertions(+), 526 deletions(-).
The main changes are:
1) Run BPF program on socket lookup, from Jakub.
2) Introduce cpumap, from Lorenzo.
3) s390 JIT fixes, from Ilya.
4) teach riscv JIT to emit compressed insns, from Luke.
5) use build time computed BTF ids in bpf iter, from Yonghong.
====================
Purely independent overlapping changes in both filter.h and xdp.h
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fe80536acf ("bareudp: Added attribute to enable & disable
rx metadata collection") breaks the the original(5.7) default behavior of
bareudp module to collect RX metadadata at the receive. It was added to
avoid the crash at the kernel neighbour subsytem when packet with metadata
from bareudp is processed. But it is no more needed as the
commit 394de110a7 ("net: Added pointer check for
dst->ops->neigh_lookup in dst_neigh_lookup_skb") solves this crash.
Fixes: fe80536acf ("bareudp: Added attribute to enable & disable rx metadata collection")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When expire_nodest_conn=1 and a destination is deleted, IPVS does not
expire the existing connections until the next matching incoming packet.
If there are many connection entries from a single client to a single
destination, many packets may get dropped before all the connections are
expired (more likely with lots of UDP traffic). An optimization can be
made where upon deletion of a destination, IPVS queues up delayed work
to immediately expire any connections with a deleted destination. This
ensures any reused source ports from a client (within the IPVS timeouts)
are scheduled to new real servers instead of silently dropped.
Signed-off-by: Andrew Sy Kim <kim.andrewsy@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add comment to describe the purpose of devlink instance lock.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commits "xfrm: Move dst->path into struct xfrm_dst"
and "net: Create and use new helper xfrm_dst_child()."
changed xfrm bundle handling under the assumption
that xdst->path and dst->child are not a NULL pointer
only if dst->xfrm is not a NULL pointer. That is true
with one exception. If the xfrm hold queue is used
to wait until a SA is installed by the key manager,
we create a dummy bundle without a valid dst->xfrm
pointer. The current xfrm bundle handling crashes
in that case. Fix this by extending the NULL check
of dst->xfrm with a test of the DST_XFRM_QUEUE flag.
Fixes: 0f6c480f23 ("xfrm: Move dst->path into struct xfrm_dst")
Fixes: b92cf4aab8 ("net: Create and use new helper xfrm_dst_child().")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Now that we have all the infrastructure in place for calling into the
dsa_ptr->netdev_ops function pointers, install them when we configure
the DSA CPU/management interface and tear them down. The flow is
unchanged from before, but now we preserve equality of tests when
network device drivers do tests like dev->netdev_ops == &foo_ops which
was not the case before since we were allocating an entirely new
structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the dsa_netdevice_ops structure which is a subset of
the net_device_ops structure for the specific operations that we care
about overlaying on top of the DSA CPU port net_device and provide
inline stubs that take core managing whether DSA code is reachable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setsockopt SOL_IP/IP_RECVERR_4884 to return the offset to an
extension struct if present.
ICMP messages may include an extension structure after the original
datagram. RFC 4884 standardized this behavior. It stores the offset
in words to the extension header in u8 icmphdr.un.reserved[1].
The field is valid only for ICMP types destination unreachable, time
exceeded and parameter problem, if length is at least 128 bytes and
entire packet does not exceed 576 bytes.
Return the offset to the start of the extension struct when reading an
ICMP error from the error queue, if it matches the above constraints.
Do not return the raw u8 field. Return the offset from the start of
the user buffer, in bytes. The kernel does not return the network and
transport headers, so subtract those.
Also validate the headers. Return the offset regardless of validation,
as an invalid extension must still not be misinterpreted as part of
the original datagram. Note that !invalid does not imply valid. If
the extension version does not match, no validation can take place,
for instance.
For backward compatibility, make this optional, set by setsockopt
SOL_IP/IP_RECVERR_RFC4884. For API example and feature test, see
github.com/wdebruij/kerneltools/blob/master/tests/recv_icmp_v2.c
For forward compatibility, reserve only setsockopt value 1, leaving
other bits for additional icmp extensions.
Changes
v1->v2:
- convert word offset to byte offset from start of user buffer
- return in ee_data as u8 may be insufficient
- define extension struct and object header structs
- return len only if constraints met
- if returning len, also validate
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xdp_get_shared_info_from_{buff,frame} utility routines to get
skb_shared_info from xdp buffer/frame pointer.
xdp_get_shared_info_from_{buff,frame} will be used to implement xdp
multi-buffer support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall(). This also removes all the now unused
compat_{get,set}sockopt methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the few cases that need special treatment in-line using
in_compat_syscall().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compat handling to sock_common_{get,set}sockopt instead,
keyed of in_compat_syscall(). This allow to remove the now unused
->compat_{get,set}sockopt methods from struct proto_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper that copies either a native or compat bpf_fprog from
userspace after verifying the length, and remove the compat setsockopt
handlers that now aren't required.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirred currently does not mix well with blocks executed after the qdisc
root lock is taken. This includes classification blocks (such as in PRIO,
ETS, DRR qdiscs) and qevents. The locking caused by the packet mirrored by
mirred can cause deadlocks: either when the thread of execution attempts to
take the lock a second time, or when two threads end up waiting on each
other's locks.
The qevent patchset attempted to not introduce further badness of this
sort, and dropped the lock before executing the qevent block. However this
lead to too little locking and races between qdisc configuration and packet
enqueue in the RED qdisc.
Before the deadlock issues are solved in a way that can be applied across
many qdiscs reasonably easily, do for qevents what is done for the
classification blocks and just keep holding the root lock.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Introduce XDP_REDIRECT support for eBPF programs attached to cpumap
entries.
This patch has been tested on Marvell ESPRESSObin using a modified
version of xdp_redirect_cpu sample in order to attach a XDP program
to CPUMAP entries to perform a redirect on the mvneta interface.
In particular the following scenario has been tested:
rq (cpu0) --> mvneta - XDP_REDIRECT (cpu0) --> CPUMAP - XDP_REDIRECT (cpu1) --> mvneta
$./xdp_redirect_cpu -p xdp_cpu_map0 -d eth0 -c 1 -e xdp_redirect \
-f xdp_redirect_kern.o -m tx_port -r eth0
tx: 285.2 Kpps rx: 285.2 Kpps
Attaching a simple XDP program on eth0 to perform XDP_TX gives
comparable results:
tx: 288.4 Kpps rx: 288.4 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/2cf8373a731867af302b00c4ff16c122630c4980.1594734381.git.lorenzo@kernel.org
Introduce the capability to attach an eBPF program to cpumap entries.
The idea behind this feature is to add the possibility to define on
which CPU run the eBPF program if the underlying hw does not support
RSS. Current supported verdicts are XDP_DROP and XDP_PASS.
This patch has been tested on Marvell ESPRESSObin using xdp_redirect_cpu
sample available in the kernel tree to identify possible performance
regressions. Results show there are no observable differences in
packet-per-second:
$./xdp_redirect_cpu --progname xdp_cpu_map0 --dev eth0 --cpu 1
rx: 354.8 Kpps
rx: 356.0 Kpps
rx: 356.8 Kpps
rx: 356.3 Kpps
rx: 356.6 Kpps
rx: 356.6 Kpps
rx: 356.7 Kpps
rx: 355.8 Kpps
rx: 356.8 Kpps
rx: 356.8 Kpps
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/5c9febdf903d810b3415732e5cd98491d7d9067a.1594734381.git.lorenzo@kernel.org
Move the guts of xdp_convert_buff_to_frame to a new helper,
xdp_update_frame_from_buff so it can be reused removing code duplication
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/90a68c283d7ebeb48924934c9b7ac79492300472.1594734381.git.lorenzo@kernel.org
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drop doubled words in several comments.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "the" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "to" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled words "or" and "the" in several comments.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled word "not" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop doubled words in two comments.
Fix a spello/typo.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 263e1201a2 ("mptcp: consolidate synack processing.")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not used since commit 09c7570480 ("xfrm: remove flow cache")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are not used any more since commit b1edeb1023 ("netlabel: Replace
protocol/NetLabel linking with refrerence counts")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend switchdev API to add support for MRP interconnect. The HW is
notified in the following cases:
SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role
of the node changes. The supported roles are MIM and MIC.
SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring
changes it states to open or closed.
SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending
MRP_InTest frames on all MRP ports. This is called only on nodes that
have the interconnect role MIM.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful for the user to know the reason behind a dropped packet.
Introduce new counters which track drops on the receive path caused by:
1. rx ring being full
2. fill ring being empty
Also, on the tx path introduce a counter which tracks the number of times
we attempt pull from the tx ring when it is empty.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200708072835.4427-2-ciara.loftus@intel.com
In preparation for users of the "install a received file" logic outside
of net/ (pidfd and seccomp), relocate and rename __scm_install_fd() from
net/core/scm.c to __receive_fd() in fs/file.c, and provide a wrapper
named receive_fd_user(), as future patches will change the interface
to __receive_fd().
Additionally add a comment to fd_install() as a counterpoint to how
__receive_fd() interacts with fput().
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Dmitry Kadashev <dkadashev@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: linux-fsdevel@vger.kernel.org
Cc: netdev@vger.kernel.org
Reviewed-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Duplicate the cleanups from commit 2618d530dd ("net/scm: cleanup
scm_detach_fds") into the compat code.
Replace open-coded __receive_sock() with a call to the helper.
Move the check added in commit 1f466e1f15 ("net: cleanly handle kernel
vs user buffers for ->msg_control") to before the compat call, even
though it should be impossible for an in-kernel call to also be compat.
Correct the int "flags" argument to unsigned int to match fd_install()
and similar APIs.
Regularize any remaining differences, including a whitespace issue,
a checkpatch warning, and add the check from commit 6900317f5e ("net,
scm: fix PaX detected msg_controllen overflow in scm_detach_fds") which
fixed an overflow unique to 64-bit. To avoid confusion when comparing
the compat handler to the native handler, just include the same check
in the compat handler.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Add missed sock updates to compat path via a new helper, which will be
used more in coming patches. (The net/core/scm.c code is left as-is here
to assist with -stable backports for the compat path.)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 48a87cc26c ("net: netprio: fd passed in SCM_RIGHTS datagram not set correctly")
Fixes: d84295067f ("net: net_cls: fd passed in SCM_RIGHTS datagram not set correctly")
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
In order to use new devlink port health reporters infrastructure, add
corresponding constructor and destructor functions.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink-health reporter support on per-port basis.
The main difference existing devlink-health is that port reporters are
stored in per-devlink_port lists. Upon creation of such health reporter the
reference to a port it belongs to is stored in reporter struct.
Fill the port index attribute in devlink-health response to
allow devlink userspace utility to distinguish between device and port
reporters.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cater to devices which:
(a) may want to sleep in the callbacks;
(b) only have IPv4 support;
(c) need all the programming to happen while the netdev is up.
Drivers attach UDP tunnel offload info struct to their netdevs,
where they declare how many UDP ports of various tunnel types
they support. Core takes care of tracking which ports to offload.
Use a fixed-size array since this matches what almost all drivers
do, and avoids a complexity and uncertainty around memory allocations
in an atomic context.
Make sure that tunnel drivers don't try to replay the ports when
new NIC netdev is registered. Automatic replays would mess up
reference counting, and will be removed completely once all drivers
are converted.
v4:
- use a #define NULL to avoid build issues with CONFIG_INET=n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to use tunnel types as flags more easily.
There doesn't appear to be any user using the type as an
array index, so this should make no difference.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new attribute that indicates the split ability of devlink port.
Drivers are expected to set it via devlink_port_attrs_set(), before
registering the port.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink port attribute that indicates the port's number of lanes.
Drivers are expected to set it via devlink_port_attrs_set(), before
registering the port.
The attribute is not passed to user space in case the number of lanes is
invalid (0).
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink_port_attrs holds the attributes of devlink_port.
Similarly to the previous patch, 'switch_port' attribute is another
exception.
Move 'switch_port' to be devlink_port's field.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct devlink_port_attrs holds the attributes of devlink_port.
The 'set' field is not devlink_port's attribute as opposed to most of the
others.
Move 'set' to be devlink_port's field called 'attrs_set'.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_sk_reuseport_detach is currently called when sk->sk_user_data
is not NULL. It is incorrect because sk->sk_user_data may not be
managed by the bpf's reuseport_array. It has been reported in [1] that,
the bpf_sk_reuseport_detach() which is called from udp_lib_unhash() has
corrupted the sk_user_data managed by l2tp.
This patch solves it by using another bit (defined as SK_USER_DATA_BPF)
of the sk_user_data pointer value. It marks that a sk_user_data is
managed/owned by BPF.
The patch depends on a PTRMASK introduced in
commit f1ff5ce2cd ("net, sk_msg: Clear sk_user_data pointer on clone if tagged").
[ Note: sk->sk_user_data is used by bpf's reuseport_array only when a sk is
added to the bpf's reuseport_array.
i.e. doing setsockopt(SO_REUSEPORT) and having "sk->sk_reuseport == 1"
alone will not stop sk->sk_user_data being used by other means. ]
[1]: https://lore.kernel.org/netdev/20200706121259.GA20199@katalix.com/
Fixes: 5dc4c4b7d4 ("bpf: Introduce BPF_MAP_TYPE_REUSEPORT_SOCKARRAY")
Reported-by: James Chapman <jchapman@katalix.com>
Reported-by: syzbot+9f092552ba9a5efca5df@syzkaller.appspotmail.com
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: James Chapman <jchapman@katalix.com>
Acked-by: James Chapman <jchapman@katalix.com>
Link: https://lore.kernel.org/bpf/20200709061110.4019316-1-kafai@fb.com
This patch is to register a callback function tunnel6_rcv_cb with
is_ipip set in a xfrm_input_afinfo object for tunnel6 and tunnel46.
It will be called by xfrm_rcv_cb() from xfrm_input() when family
is AF_INET6 and proto is IPPROTO_IPIP or IPPROTO_IPV6.
v1->v2:
- Fix a sparse warning caused by the missing "__rcu", as Jakub
noticed.
- Handle the err returned by xfrm_input_register_afinfo() in
tunnel6_init/fini(), as Sabrina noticed.
v2->v3:
- Add "#if IS_ENABLED(CONFIG_INET6_XFRM_TUNNEL)" to fix the build error
when xfrm is disabled, reported by kbuild test robot
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch is to register a callback function tunnel4_rcv_cb with
is_ipip set in a xfrm_input_afinfo object for tunnel4 and tunnel64.
It will be called by xfrm_rcv_cb() from xfrm_input() when family
is AF_INET and proto is IPPROTO_IPIP or IPPROTO_IPV6.
v1->v2:
- Fix a sparse warning caused by the missing "__rcu", as Jakub
noticed.
- Handle the err returned by xfrm_input_register_afinfo() in
tunnel4_init/fini(), as Sabrina noticed.
v2->v3:
- Add "#if IS_ENABLED(CONFIG_INET_XFRM_TUNNEL)" to fix the build error
when xfrm is disabled, reported by kbuild test robot.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch is to add a new member is_ipip to struct xfrm_input_afinfo,
to allow another group family of callback functions to be registered
with is_ipip set.
This will be used for doing a callback for struct xfrm(6)_tunnel of
ipip/ipv6 tunnels in xfrm_input() by calling xfrm_rcv_cb(), which is
needed by ipip/ipv6 tunnels' support in ip(6)_vti and xfrm interface
in the next patches.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This implements the known parts of the Realtek 4 byte
tag protocol version 0xA, as found in the RTL8366RB
DSA switch.
It is designated as protocol version 0xA as a
different Realtek 4 byte tag format with protocol
version 0x9 is known to exist in the Realtek RTL8306
chips.
The tag and switch chip lacks public documentation, so
the tag format has been reverse-engineered from
packet dumps. As only ingress traffic has been available
for analysis an egress tag has not been possible to
develop (even using educated guesses about bit fields)
so this is as far as it gets. It is not known if the
switch even supports egress tagging.
Excessive attempts to figure out the egress tag format
was made. When nothing else worked, I just tried all bit
combinations with 0xannp where a is protocol and p is
port. I looped through all values several times trying
to get a response from ping, without any positive
result.
Using just these ingress tags however, the switch
functionality is vastly improved and the packets find
their way into the destination port without any
tricky VLAN configuration. On the D-Link DIR-685 the
LAN ports now come up and respond to ping without
any command line configuration so this is a real
improvement for users.
Egress packets need to be restricted to the proper
target ports using VLAN, which the RTL8366RB DSA
switch driver already sets up.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Support for rejecting packets from the prerouting chain, from
Laura Garcia Liebana.
2) Remove useless assignment in pipapo, from Stefano Brivio.
3) On demand hook registration in IPVS, from Julian Anastasov.
4) Expire IPVS connection from process context to not overload
timers, also from Julian.
5) Fallback to conntrack TCP tracker to handle connection reuse
in IPVS, from Julian Anastasov.
6) Several patches to support for chain bindings.
7) Expose enum nft_chain_flags through UAPI.
8) Reject unsupported chain flags from the netlink control plane.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-07-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 17 day(s) which contain
a total of 106 files changed, 5233 insertions(+), 1283 deletions(-).
The main changes are:
1) bpftool ability to show PIDs of processes having open file descriptors
for BPF map/program/link/BTF objects, relying on BPF iterator progs
to extract this info efficiently, from Andrii Nakryiko.
2) Addition of BPF iterator progs for dumping TCP and UDP sockets to
seq_files, from Yonghong Song.
3) Support access to BPF map fields in struct bpf_map from programs
through BTF struct access, from Andrey Ignatov.
4) Add a bpf_get_task_stack() helper to be able to dump /proc/*/stack
via seq_file from BPF iterator progs, from Song Liu.
5) Make SO_KEEPALIVE and related options available to bpf_setsockopt()
helper, from Dmitry Yakunin.
6) Optimize BPF sk_storage selection of its caching index, from Martin
KaFai Lau.
7) Removal of redundant synchronize_rcu()s from BPF map destruction which
has been a historic leftover, from Alexei Starovoitov.
8) Several improvements to test_progs to make it easier to create a shell
loop that invokes each test individually which is useful for some CIs,
from Jesper Dangaard Brouer.
9) Fix bpftool prog dump segfault when compiled without skeleton code on
older clang versions, from John Fastabend.
10) Bunch of cleanups and minor improvements, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This new chain flag specifies that:
* the kernel dynamically allocates the chain name, if no chain name
is specified.
* If the immediate expression that refers to this chain is removed,
then this bound chain (and its content) is destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This enum definition was never exposed through UAPI. Rename
NFT_BASE_CHAIN to NFT_CHAIN_BASE for consistency.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This netlink attribute allows you to refer to chains inside a
transaction as an alternative to the name and the handle. The chain
binding support requires this new chain ID approach.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
YangYuxi is reporting that connection reuse
is causing one-second delay when SYN hits
existing connection in TIME_WAIT state.
Such delay was added to give time to expire
both the IPVS connection and the corresponding
conntrack. This was considered a rare case
at that time but it is causing problem for
some environments such as Kubernetes.
As nf_conntrack_tcp_packet() can decide to
release the conntrack in TIME_WAIT state and
to replace it with a fresh NEW conntrack, we
can use this to allow rescheduling just by
tuning our check: if the conntrack is
confirmed we can not schedule it to different
real server and the one-second delay still
applies but if new conntrack was created,
we are free to select new real server without
any delays.
YangYuxi lists some of the problem reports:
- One second connection delay in masquerading mode:
https://marc.info/?t=151683118100004&r=1&w=2
- IPVS low throughput #70747
https://github.com/kubernetes/kubernetes/issues/70747
- Apache Bench can fill up ipvs service proxy in seconds #544https://github.com/cloudnativelabs/kube-router/issues/544
- Additional 1s latency in `host -> service IP -> pod`
https://github.com/kubernetes/kubernetes/issues/90854
Fixes: f719e3754e ("ipvs: drop first packet to redirect conntrack")
Co-developed-by: YangYuxi <yx.atom1@gmail.com>
Signed-off-by: YangYuxi <yx.atom1@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are a couple of places in net/sched/ that check skb->protocol and act
on the value there. However, in the presence of VLAN tags, the value stored
in skb->protocol can be inconsistent based on whether VLAN acceleration is
enabled. The commit quoted in the Fixes tag below fixed the users of
skb->protocol to use a helper that will always see the VLAN ethertype.
However, most of the callers don't actually handle the VLAN ethertype, but
expect to find the IP header type in the protocol field. This means that
things like changing the ECN field, or parsing diffserv values, stops
working if there's a VLAN tag, or if there are multiple nested VLAN
tags (QinQ).
To fix this, change the helper to take an argument that indicates whether
the caller wants to skip the VLAN tags or not. When skipping VLAN tags, we
make sure to skip all of them, so behaviour is consistent even in QinQ
mode.
To make the helper usable from the ECN code, move it to if_vlan.h instead
of pkt_sched.h.
v3:
- Remove empty lines
- Move vlan variable definitions inside loop in skb_protocol()
- Also use skb_protocol() helper in IP{,6}_ECN_decapsulate() and
bpf_skb_ecn_set_ce()
v2:
- Use eth_type_vlan() helper in skb_protocol()
- Also fix code that reads skb->protocol directly
- Change a couple of 'if/else if' statements to switch constructs to avoid
calling the helper twice
Reported-by: Ilya Ponetayev <i.ponetaev@ndmsystems.com>
Fixes: d8b9605d26 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, bonding xfrm crypto offload can only be set up if the bonding
module is loaded with active-backup mode already set. We need to be able to
make this work with bonds set to AB after the bonding driver has already
been loaded.
So what's done here is:
1) move #define BOND_XFRM_FEATURES to net/bonding.h so it can be used
by both bond_main.c and bond_options.c
2) set BOND_XFRM_FEATURES in bond_dev->hw_features universally, rather than
only when loading in AB mode
3) wire up xfrmdev_ops universally too
4) disable BOND_XFRM_FEATURES in bond_dev->features if not AB
5) exit early (non-AB case) from bond_ipsec_offload_ok, to prevent a
performance hit from traversing into the underlying drivers
5) toggle BOND_XFRM_FEATURES in bond_dev->wanted_features and call
netdev_change_features() from bond_option_mode_set()
In my local testing, I can change bonding modes back and forth on the fly,
have hardware offload work when I'm in AB, and see no performance penalty
to non-AB software encryption, despite having xfrm bits all wired up for
all modes now.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Reported-by: Huy Nguyen <huyn@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A potential deadlock can occur during registering or unregistering a
new generic netlink family between the main nl_table_lock and the
cb_lock where each thread wants the lock held by the other, as
demonstrated below.
1) Thread 1 is performing a netlink_bind() operation on a socket. As part
of this call, it will call netlink_lock_table(), incrementing the
nl_table_users count to 1.
2) Thread 2 is registering (or unregistering) a genl_family via the
genl_(un)register_family() API. The cb_lock semaphore will be taken for
writing.
3) Thread 1 will call genl_bind() as part of the bind operation to handle
subscribing to GENL multicast groups at the request of the user. It will
attempt to take the cb_lock semaphore for reading, but it will fail and
be scheduled away, waiting for Thread 2 to finish the write.
4) Thread 2 will call netlink_table_grab() during the (un)registration
call. However, as Thread 1 has incremented nl_table_users, it will not
be able to proceed, and both threads will be stuck waiting for the
other.
genl_bind() is a noop, unless a genl_family implements the mcast_bind()
function to handle setting up family-specific multicast operations. Since
no one in-tree uses this functionality as Cong pointed out, simply removing
the genl_bind() function will remove the possibility for deadlock, as there
is no attempt by Thread 1 above to take the cb_lock semaphore.
Fixes: c380d9a7af ("genetlink: pass multicast bind/unbind to families")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-06-30
The following pull-request contains BPF updates for your *net* tree.
We've added 28 non-merge commits during the last 9 day(s) which contain
a total of 35 files changed, 486 insertions(+), 232 deletions(-).
The main changes are:
1) Fix an incorrect verifier branch elimination for PTR_TO_BTF_ID pointer
types, from Yonghong Song.
2) Fix UAPI for sockmap and flow_dissector progs that were ignoring various
arguments passed to BPF_PROG_{ATTACH,DETACH}, from Lorenz Bauer & Jakub Sitnicki.
3) Fix broken AF_XDP DMA hacks that are poking into dma-direct and swiotlb
internals and integrate it properly into DMA core, from Christoph Hellwig.
4) Fix RCU splat from recent changes to avoid skipping ingress policy when
kTLS is enabled, from John Fastabend.
5) Fix BPF ringbuf map to enforce size to be the power of 2 in order for its
position masking to work, from Andrii Nakryiko.
6) Fix regression from CAP_BPF work to re-allow CAP_SYS_ADMIN for loading
of network programs, from Maciej Żenczykowski.
7) Fix libbpf section name prefix for devmap progs, from Jesper Dangaard Brouer.
8) Fix formatting in UAPI documentation for BPF helpers, from Quentin Monnet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Left shifting the u16 value promotes it to a int and then it
gets sign extended to a u64. If len << 16 is greater than 0x7fffffff
then the upper bits get set to 1 because of the implicit sign extension.
Fix this by casting len to u64 before shifting it.
Addresses-Coverity: ("integer handling issues")
Fixes: ed9b7646b0 ("net/tls: Add asynchronous resync")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices that take straight up layer 3 packets benefit from having a
shared header_ops so that AF_PACKET sockets can inject packets that are
recognized. This shared infrastructure will be used by other drivers
that currently can't inject packets using AF_PACKET. It also exposes the
parser function, as it is useful in standalone form too.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support multi-prog link-based attachments for new netns attach types, we
need to keep track of more than one bpf_link per attach type. Hence,
convert net->bpf.links into a list, that currently can be either empty or
have just one item.
Instead of reusing bpf_prog_list from bpf-cgroup, we link together
bpf_netns_link's themselves. This makes list management simpler as we don't
have to allocate, initialize, and later release list elements. We can do
this because multi-prog attachment will be available only for bpf_link, and
we don't need to build a list of programs attached directly and indirectly
via links.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-4-jakub@cloudflare.com
Prepare for having multi-prog attachments for new netns attach types by
storing programs to run in a bpf_prog_array, which is well suited for
iterating over programs and running them in sequence.
After this change bpf(PROG_QUERY) may block to allocate memory in
bpf_prog_array_copy_to_user() for collected program IDs. This forces a
change in how we protect access to the attached program in the query
callback. Because bpf_prog_array_copy_to_user() can sleep, we switch from
an RCU read lock to holding a mutex that serializes updaters.
Because we allow only one BPF flow_dissector program to be attached to
netns at all times, the bpf_prog_array pointed by net->bpf.run_array is
always either detached (null) or one element long.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-3-jakub@cloudflare.com
Prepare for using bpf_prog_array to store attached programs by moving out
code that updates the attached program out of flow dissector.
Managing bpf_prog_array is more involved than updating a single bpf_prog
pointer. This will let us do it all from one place, bpf/net_namespace.c, in
the subsequent patch.
No functional change intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200625141357.910330-2-jakub@cloudflare.com
Keep the IPVS hooks registered in Netfilter only
while there are configured virtual services. This
saves CPU cycles while IPVS is loaded but not used.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Invert the polarity and better name the flag so that the use case is
properly documented.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200629130359.2690853-3-hch@lst.de
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Improve hardware layouts and structure for kTLS support
2) Generalize ICOSQ (Internal Channel Operations Send Queue)
Due to the asynchronous nature of adding new kTLS flows and handling
HW asynchronous kTLS resync requests, the XSK ICOSQ was extended to
support generic async operations, such as kTLS add flow and resync, in
addition to the existing XSK usages.
3) kTLS hardware flow steering and classification:
The driver already has the means to classify TCP ipv4/6 flows to send them
to the corresponding RSS HW engine, as reflected in patches 3 through 5,
the series will add a steering layer that will hook to the driver's TCP
classifiers and will match on well known kTLS connection, in case of a
match traffic will be redirected to the kTLS decryption engine, otherwise
traffic will continue flowing normally to the TCP RSS engine.
3) kTLS add flow RX HW offload support
New offload contexts post their static/progress params WQEs
(Work Queue Element) to communicate the newly added kTLS contexts
over the per-channel async ICOSQ.
The Channel/RQ is selected according to the socket's rxq index.
A new TLS-RX workqueue is used to allow asynchronous addition of
steering rules, out of the NAPI context.
It will be also used in a downstream patch in the resync procedure.
Feature is OFF by default. Can be turned on by:
$ ethtool -K <if> tls-hw-rx-offload on
4) Added mlx5 kTLS sw stats and new counters are documented in
Documentation/networking/tls-offload.rst
rx_tls_ctx - number of TLS RX HW offload contexts added to device for
decryption.
rx_tls_ooo - number of RX packets which were part of a TLS stream
but did not arrive in the expected order and triggered the resync
procedure.
rx_tls_del - number of TLS RX HW offload contexts deleted from device
(connection has finished).
rx_tls_err - number of RX packets which were part of a TLS stream
but were not decrypted due to unexpected error in the state machine.
5) Asynchronous RX resync
a. The NIC driver indicates that it would like to resync on some TLS
record within the received packet (P), but the driver does not
know (yet) which of the TLS records within the packet.
At this stage, the NIC driver will query the device to find the exact
TCP sequence for resync (tcpsn), however, the driver does not wait
for the device to provide the response.
b. Eventually, the device responds, and the driver provides the tcpsn
within the resync packet to KTLS. Now, KTLS can check the tcpsn against
any processed TLS records within packet P, and also against any record
that is processed in the future within packet P.
The asynchronous resync path simplifies the device driver, as it can
save bits on the packet completion (32-bit TCP sequence), and pass this
information on an asynchronous command instead.
Performance:
CPU: Intel(R) Xeon(R) CPU E5-2687W v4 @ 3.00GHz, 24 cores, HT off
NIC: ConnectX-6 Dx 100GbE dual port
Goodput (app-layer throughput) comparison:
+---------------+-------+-------+---------+
| # connections | 1 | 4 | 8 |
+---------------+-------+-------+---------+
| SW (Gbps) | 7.26 | 24.70 | 50.30 |
+---------------+-------+-------+---------+
| HW (Gbps) | 18.50 | 64.30 | 92.90 |
+---------------+-------+-------+---------+
| Speedup | 2.55x | 2.56x | 1.85x * |
+---------------+-------+-------+---------+
* After linerate is reached, diff is observed in CPU util
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl73s2kACgkQSD+KveBX
+j4wqAf/ZhcEn7i4N2F9wMMIL6wd4DgwKWWhbGpiREIxDwcRbqH7PGom8nBZMNd9
+3g3zfURvByWehLtYcjmMgR4B7+xDgEs0dSx6pQM9764HqLDV2jW8ENr9Vr/u8s1
hJ/eV8uzIfvx27MzbENZi0oJTw7N9nCgdcv1OyZkIba+Iado9pOeakPgBmTbINgo
46LJI9nIEROE15gfjyxrVeYAs3Nxt+bogQCWYfMqUfRmKcMJ0d4oTHaUdtmm+xQB
jC685/e4gE7jRgZ3qH/xvCZYp7+TVKaXsB0EtaJdPFEkvvvQpgPTfquIQ+6l7vvE
Yf1YUhnDOoxGUQy1CdSZ2reNxLIm8A==
=7+rG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-tls-2020-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-tls-2020-06-26
1) Improve hardware layouts and structure for kTLS support
2) Generalize ICOSQ (Internal Channel Operations Send Queue)
Due to the asynchronous nature of adding new kTLS flows and handling
HW asynchronous kTLS resync requests, the XSK ICOSQ was extended to
support generic async operations, such as kTLS add flow and resync, in
addition to the existing XSK usages.
3) kTLS hardware flow steering and classification:
The driver already has the means to classify TCP ipv4/6 flows to send them
to the corresponding RSS HW engine, as reflected in patches 3 through 5,
the series will add a steering layer that will hook to the driver's TCP
classifiers and will match on well known kTLS connection, in case of a
match traffic will be redirected to the kTLS decryption engine, otherwise
traffic will continue flowing normally to the TCP RSS engine.
3) kTLS add flow RX HW offload support
New offload contexts post their static/progress params WQEs
(Work Queue Element) to communicate the newly added kTLS contexts
over the per-channel async ICOSQ.
The Channel/RQ is selected according to the socket's rxq index.
A new TLS-RX workqueue is used to allow asynchronous addition of
steering rules, out of the NAPI context.
It will be also used in a downstream patch in the resync procedure.
Feature is OFF by default. Can be turned on by:
$ ethtool -K <if> tls-hw-rx-offload on
4) Added mlx5 kTLS sw stats and new counters are documented in
Documentation/networking/tls-offload.rst
rx_tls_ctx - number of TLS RX HW offload contexts added to device for
decryption.
rx_tls_ooo - number of RX packets which were part of a TLS stream
but did not arrive in the expected order and triggered the resync
procedure.
rx_tls_del - number of TLS RX HW offload contexts deleted from device
(connection has finished).
rx_tls_err - number of RX packets which were part of a TLS stream
but were not decrypted due to unexpected error in the state machine.
5) Asynchronous RX resync
a. The NIC driver indicates that it would like to resync on some TLS
record within the received packet (P), but the driver does not
know (yet) which of the TLS records within the packet.
At this stage, the NIC driver will query the device to find the exact
TCP sequence for resync (tcpsn), however, the driver does not wait
for the device to provide the response.
b. Eventually, the device responds, and the driver provides the tcpsn
within the resync packet to KTLS. Now, KTLS can check the tcpsn against
any processed TLS records within packet P, and also against any record
that is processed in the future within packet P.
The asynchronous resync path simplifies the device driver, as it can
save bits on the packet completion (32-bit TCP sequence), and pass this
information on an asynchronous command instead.
Performance:
CPU: Intel(R) Xeon(R) CPU E5-2687W v4 @ 3.00GHz, 24 cores, HT off
NIC: ConnectX-6 Dx 100GbE dual port
Goodput (app-layer throughput) comparison:
+---------------+-------+-------+---------+
| # connections | 1 | 4 | 8 |
+---------------+-------+-------+---------+
| SW (Gbps) | 7.26 | 24.70 | 50.30 |
+---------------+-------+-------+---------+
| HW (Gbps) | 18.50 | 64.30 | 92.90 |
+---------------+-------+-------+---------+
| Speedup | 2.55x | 2.56x | 1.85x * |
+---------------+-------+-------+---------+
* After linerate is reached, diff is observed in CPU util
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
genl_family_rcv_msg_attrs_parse() reuses the global family->attrbuf
when family->parallel_ops is false. However, family->attrbuf is not
protected by any lock on the genl_family_rcv_msg_doit() code path.
This leads to several different consequences, one of them is UAF,
like the following:
genl_family_rcv_msg_doit(): genl_start():
genl_family_rcv_msg_attrs_parse()
attrbuf = family->attrbuf
__nlmsg_parse(attrbuf);
genl_family_rcv_msg_attrs_parse()
attrbuf = family->attrbuf
__nlmsg_parse(attrbuf);
info->attrs = attrs;
cb->data = info;
netlink_unicast_kernel():
consume_skb()
genl_lock_dumpit():
genl_dumpit_info(cb)->attrs
Note family->attrbuf is an array of pointers to the skb data, once
the skb is freed, any dereference of family->attrbuf will be a UAF.
Maybe we could serialize the family->attrbuf with genl_mutex too, but
that would make the locking more complicated. Instead, we can just get
rid of family->attrbuf and always allocate attrbuf from heap like the
family->parallel_ops==true code path. This may add some performance
overhead but comparing with taking the global genl_mutex, it still
looks better.
Fixes: 75cdbdd089 ("net: ieee802154: have genetlink code to parse the attrs during dumpit")
Fixes: 057af70713 ("net: tipc: have genetlink code to parse the attrs during dumpit")
Reported-and-tested-by: syzbot+3039ddf6d7b13daf3787@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+80cad1e3cb4c41cde6ff@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+736bcbcb11b60d0c0792@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+520f8704db2b68091d44@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+c96e4dfb32f8987fdeed@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow acting on dropped and/or ECN-marked packets, add two new
qevents to the RED qdisc: "early_drop" and "mark". Filters attached at
"early_drop" block are executed as packets are early-dropped, those
attached at the "mark" block are executed as packets are ECN-marked.
Two new attributes are introduced: TCA_RED_EARLY_DROP_BLOCK with the block
index for the "early_drop" qevent, and TCA_RED_MARK_BLOCK for the "mark"
qevent. Absence of these attributes signifies "don't care": no block is
allocated in that case, or the existing blocks are left intact in case of
the change callback.
For purposes of offloading, blocks attached to these qevents appear with
newly-introduced binder types, FLOW_BLOCK_BINDER_TYPE_RED_EARLY_DROP and
FLOW_BLOCK_BINDER_TYPE_RED_MARK.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qevents are attach points for TC blocks, where filters can be put that are
executed when "interesting events" take place in a qdisc. The data to keep
and the functions to invoke to maintain a qevent will be largely the same
between qevents. Therefore introduce sched-wide helpers for qevent
management.
Currently, similarly to ingress and egress blocks of clsact pseudo-qdisc,
blocks attachment cannot be changed after the qdisc is created. To that
end, add a helper tcf_qevent_validate_change(), which verifies whether
block index attribute is not attached, or if it is, whether its value
matches the current one (i.e. there is no material change).
The function tcf_qevent_handle() should be invoked when qdisc hits the
"interesting event" corresponding to a block. This function releases root
lock for the duration of executing the attached filters, to allow packets
generated through user actions (notably mirred) to be reinserted to the
same qdisc tree.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patch introduces qevents, points in qdisc algorithm where
packet can be processed by user-defined filters. Should this processing
lead to a situation where a new packet is to be enqueued on the same port,
holding the root lock would lead to deadlocks. To solve the issue, qevent
handler needs to unlock and relock the root lock when necessary.
To that end, add the root lock argument to the qdisc op enqueue, and
propagate throughout.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_is_singular() instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Metadata need not be collected in receive if the packet from bareudp
device is not targeted to openvswitch.
Signed-off-by: Martin <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for asynchronous resynchronization in tls_device.
Async resync follows two distinct stages:
1. The NIC driver indicates that it would like to resync on some TLS
record within the received packet (P), but the driver does not
know (yet) which of the TLS records within the packet.
At this stage, the NIC driver will query the device to find the exact
TCP sequence for resync (tcpsn), however, the driver does not wait
for the device to provide the response.
2. Eventually, the device responds, and the driver provides the tcpsn
within the resync packet to KTLS. Now, KTLS can check the tcpsn against
any processed TLS records within packet P, and also against any record
that is processed in the future within packet P.
The asynchronous resync path simplifies the device driver, as it can
save bits on the packet completion (32-bit TCP sequence), and pass this
information on an asynchronous command instead.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit b3ae2459f8.
Revert the force resync API.
Not in use. To be replaced by a better async resync API downstream.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket is set ipv6only, it will still send IPv4 addresses in the
INIT and INIT_ACK packets. This potentially misleads the peer into using
them, which then would cause association termination.
The fix is to not add IPv4 addresses to ipv6only sockets.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware device may include more than one police entry. Specifying the
action's index make it possible for several tc filters to share the same
police action when installing the filters.
Propagate this index to device drivers through the flow offload
intermediate representation, so that drivers could share a single
hardware policer between multiple filters.
v1->v2 changes:
- Update the commit message suggest by Ido Schimmel <idosch@idosch.org>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current police offloading support the 'burst'' and 'rate_bytes_ps'. Some
hardware own the capability to limit the frame size. If the frame size
larger than the setting, the frame would be dropped. For the police
action itself already accept the 'mtu' parameter in tc command. But not
extend to tc flower offloading. So extend 'mtu' to tc flower offloading.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to tcp_iter_state, a new field bpf_seq_afinfo is
added to udp_iter_state to provide bpf udp iterator
afinfo.
This does not change /proc/net/{udp, udp6} behavior. But
it enables bpf iterator to avoid get afinfo from PDE_DATA
and iterate through all udp and udp6 sockets in one pass.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200623230812.3988347-1-yhs@fb.com
A new field bpf_seq_afinfo is added to tcp_iter_state
to provide bpf tcp iterator afinfo. There are two
reasons on why we did this.
First, the current way to get afinfo from PDE_DATA
does not work for bpf iterator as its seq_file
inode does not conform to /proc/net/{tcp,tcp6}
inode structures. More specifically, anonymous
bpf iterator will use an anonymous inode which
is shared in the system and we cannot change inode
private data structure at all.
Second, bpf iterator for tcp/tcp6 wants to
traverse all tcp and tcp6 sockets in one pass
and bpf program can control whether they want
to skip one sk_family or not. Having a different
afinfo with family AF_UNSPEC make it easier
to understand in the code.
This patch does not change /proc/net/{tcp,tcp6} behavior
as the bpf_seq_afinfo will be NULL for these two proc files.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200623230804.3987829-1-yhs@fb.com
In commit ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list"),
it would take 'priority' to make a policy unique, and allow duplicated
policies with different 'priority' to be added, which is not expected
by userland, as Tobias reported in strongswan.
To fix this duplicated policies issue, and also fix the issue in
commit ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list"),
when doing add/del/get/update on user interfaces, this patch is to change
to look up a policy with both mark and mask by doing:
mark.v == pol->mark.v && mark.m == pol->mark.m
and leave the check:
(mark & pol->mark.m) == pol->mark.v
for tx/rx path only.
As the userland expects an exact mark and mask match to manage policies.
v1->v2:
- make xfrm_policy_mark_match inline and fix the changelog as
Tobias suggested.
Fixes: 295fae5688 ("xfrm: Allow user space manipulation of SPD mark")
Fixes: ed17b8d377 ("xfrm: fix a warning in xfrm_policy_insert_list")
Reported-by: Tobias Brunner <tobias@strongswan.org>
Tested-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Clearing the sock TX queue in sk_set_socket() might cause unexpected
out-of-order transmit when called from sock_orphan(), as outstanding
packets can pick a different TX queue and bypass the ones already queued.
This is undesired in general. More specifically, it breaks the in-order
scheduling property guarantee for device-offloaded TLS sockets.
Remove the call to sk_tx_queue_clear() in sk_set_socket(), and add it
explicitly only where needed.
Fixes: e022f0b4a0 ("net: Introduce sk_tx_queue_mapping")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
function ipv6_rpl_srh_alloc_size() and replace kzalloc() with kcalloc(),
which has a 2-factor argument form for multiplication.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes following warnings :
CC net/ipv4/udp_offload.o
net/ipv4/udp_offload.c:504:17: warning: no previous prototype for 'udp4_gro_receive' [-Wmissing-prototypes]
504 | struct sk_buff *udp4_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv4/udp_offload.c:584:29: warning: no previous prototype for 'udp4_gro_complete' [-Wmissing-prototypes]
584 | INDIRECT_CALLABLE_SCOPE int udp4_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
CHECK net/ipv6/udp_offload.c
net/ipv6/udp_offload.c:115:16: warning: symbol 'udp6_gro_receive' was not declared. Should it be static?
net/ipv6/udp_offload.c:148:29: warning: symbol 'udp6_gro_complete' was not declared. Should it be static?
CC net/ipv6/udp_offload.o
net/ipv6/udp_offload.c:115:17: warning: no previous prototype for 'udp6_gro_receive' [-Wmissing-prototypes]
115 | struct sk_buff *udp6_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv6/udp_offload.c:148:29: warning: no previous prototype for 'udp6_gro_complete' [-Wmissing-prototypes]
148 | INDIRECT_CALLABLE_SCOPE int udp6_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes following (C=1 W=1) warnings for CONFIG_RETPOLINE=y :
net/ipv4/tcp_offload.c:306:16: warning: symbol 'tcp4_gro_receive' was not declared. Should it be static?
net/ipv4/tcp_offload.c:306:17: warning: no previous prototype for 'tcp4_gro_receive' [-Wmissing-prototypes]
net/ipv4/tcp_offload.c:319:29: warning: symbol 'tcp4_gro_complete' was not declared. Should it be static?
net/ipv4/tcp_offload.c:319:29: warning: no previous prototype for 'tcp4_gro_complete' [-Wmissing-prototypes]
CHECK net/ipv6/tcpv6_offload.c
net/ipv6/tcpv6_offload.c:16:16: warning: symbol 'tcp6_gro_receive' was not declared. Should it be static?
net/ipv6/tcpv6_offload.c:29:29: warning: symbol 'tcp6_gro_complete' was not declared. Should it be static?
CC net/ipv6/tcpv6_offload.o
net/ipv6/tcpv6_offload.c:16:17: warning: no previous prototype for 'tcp6_gro_receive' [-Wmissing-prototypes]
16 | struct sk_buff *tcp6_gro_receive(struct list_head *head, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~
net/ipv6/tcpv6_offload.c:29:29: warning: no previous prototype for 'tcp6_gro_complete' [-Wmissing-prototypes]
29 | INDIRECT_CALLABLE_SCOPE int tcp6_gro_complete(struct sk_buff *skb, int thoff)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare ipv4_specific once, in tcp.h were it belongs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_specific should be declared in tcp include files,
not mptcp.
This removes the following warning :
CHECK net/ipv6/tcp_ipv6.c
net/ipv6/tcp_ipv6.c:78:42: warning: symbol 'ipv6_specific' was not declared. Should it be static?
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove these errors:
net/ipv6/tcp_ipv6.c:1550:29: warning: symbol 'tcp_v6_rcv' was not declared. Should it be static?
net/ipv6/tcp_ipv6.c:1770:30: warning: symbol 'tcp_v6_early_demux' was not declared. Should it be static?
net/ipv6/tcp_ipv6.c:1550:29: warning: no previous prototype for 'tcp_v6_rcv' [-Wmissing-prototypes]
1550 | INDIRECT_CALLABLE_SCOPE int tcp_v6_rcv(struct sk_buff *skb)
| ^~~~~~~~~~
net/ipv6/tcp_ipv6.c:1770:30: warning: no previous prototype for 'tcp_v6_early_demux' [-Wmissing-prototypes]
1770 | INDIRECT_CALLABLE_SCOPE void tcp_v6_early_demux(struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~~~
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than requiring every hw crypto capable NIC driver to do a check for
slave_dev being set, set real_dev in the xfrm layer and xso init time, and
then override it in the bonding driver as needed. Then NIC drivers can
always use real_dev, and at the same time, we eliminate the use of a
variable name that probably shouldn't have been used in the first place,
particularly given recent current events.
CC: Boris Pismenny <borisp@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that a considerable amount of cycles were spent on the
expensive indirect calls on fib6_rule_lookup. This patch introduces an
inline helper called pol_route_func that uses the indirect_call_wrappers
to avoid the indirect calls.
This patch saves around 50ns per call.
Performance was measured on the receiver by checking the amount of
syncookies that server was able to generate under a synflood load.
Traffic was generated using trafgen[1] which was pushing around 1Mpps on
a single queue. Receiver was using only one rx queue which help to
create a bottle neck and make the experiment rx-bounded.
These are the syncookies generated over 10s from the different runs:
Whithout the patch:
TcpExtSyncookiesSent 3553749 0.0
TcpExtSyncookiesSent 3550895 0.0
TcpExtSyncookiesSent 3553845 0.0
TcpExtSyncookiesSent 3541050 0.0
TcpExtSyncookiesSent 3539921 0.0
TcpExtSyncookiesSent 3557659 0.0
TcpExtSyncookiesSent 3526812 0.0
TcpExtSyncookiesSent 3536121 0.0
TcpExtSyncookiesSent 3529963 0.0
TcpExtSyncookiesSent 3536319 0.0
With the patch:
TcpExtSyncookiesSent 3611786 0.0
TcpExtSyncookiesSent 3596682 0.0
TcpExtSyncookiesSent 3606878 0.0
TcpExtSyncookiesSent 3599564 0.0
TcpExtSyncookiesSent 3601304 0.0
TcpExtSyncookiesSent 3609249 0.0
TcpExtSyncookiesSent 3617437 0.0
TcpExtSyncookiesSent 3608765 0.0
TcpExtSyncookiesSent 3620205 0.0
TcpExtSyncookiesSent 3601895 0.0
Without the patch the average is 354263 pkt/s or 2822 ns/pkt and with
the patch the average is 360738 pkt/s or 2772 ns/pkt which gives an
estimate of 50 ns per packet.
[1] http://netsniff-ng.org/
Changelog since v1:
- Change ordering in the ICW (Paolo Abeni)
Cc: Luigi Rizzo <lrizzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board serial number is a serial number, often available in PCI
*Vital Product Data*.
Also, update devlink-info.rst documentation file.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, this support is limited to active-backup mode, as I'm not sure
about the feasilibity of mapping an xfrm_state's offload handle to
multiple hardware devices simultaneously, and we rely on being able to
pass some hints to both the xfrm and NIC driver about whether or not
they're operating on a slave device.
I've tested this atop an Intel x520 device (ixgbe) using libreswan in
transport mode, succesfully achieving ~4.3Gbps throughput with netperf
(more or less identical to throughput on a bare NIC in this system),
as well as successful failover and recovery mid-netperf.
v2: just use CONFIG_XFRM_OFFLOAD for wrapping, isolate more code with it
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is prep work for initial support of bonding hardware encryption
pass-through support. The bonding driver will fill in the slave_dev
pointer, and we use that to know not to skb_push() again on a given
skb that was already processed on the bond device.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI PF and VF devlink port can manage the function represented by a
devlink port.
Allow users to set port function's hardware address.
Example of a PCI VF port which supports a port function:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
function:
hw_addr 00:00:00:00:00:00
$ devlink port function set pci/0000:06:00.0/2 hw_addr 00:11:22:33:44:55
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
function:
hw_addr 00:11:22:33:44:55
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI PF and VF devlink port can manage the function represented by
a devlink port.
Enable users to query port function's hardware address.
Example of a PCI VF port which supports a port function:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
function:
hw_addr 00:11:22:33:44:66
$ devlink port show pci/0000:06:00.0/2 -jp
{
"port": {
"pci/0000:06:00.0/2": {
"type": "eth",
"netdev": "enp6s0pf0vf1",
"flavour": "pcivf",
"pfnum": 0,
"vfnum": 1,
"function": {
"hw_addr": "00:11:22:33:44:66"
}
}
}
}
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mitigate RETPOLINE costs in __tcp_transmit_skb()
by using INDIRECT_CALL_INET() wrapper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mitigate RETPOLINE costs in __tcp_transmit_skb()
by using INDIRECT_CALL_INET() wrapper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be useful to allow busy poll for tunneled traffic. In case of
busy poll for sessions over tunnels, the underlying physical device's
queues need to be polled.
Tunnels schedule NAPI either via netif_rx() for backlog queue or
schedule the gro_cell_poll(). netif_rx() propagates the valid skb->napi_id
to the socket. OTOH, gro_cell_poll() stamps the skb->napi_id again by
calling skb_mark_napi_id() with the tunnel NAPI which is not a busy poll
candidate. This was preventing tunneled traffic to use busy poll. A valid
NAPI ID in the skb indicates it was already marked for busy poll by a
NAPI driver and hence needs to be copied into the socket.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to l3mdev (the core code for Layer 3 master devices) in
order to find out the corresponding VRF device for a given table id.
Therefore, the l3mdev implementations:
- can register a callback that returns the device index of the l3mdev
associated with a given table id;
- can offer the lookup function (table to VRF device).
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the representor is removed, then identify the indirect flow_blocks
that need to be removed by the release callback and the port representor
structure. To identify the port representor structure, a new
indr.cb_priv field needs to be introduced. The flow_block also needs to
be removed from the driver list from the cleanup path.
Fixes: 1fac52da59 ("net: flow_offload: consolidate indirect flow_block infrastructure")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare fix the bug in the next patch. use flow_indr_block_cb_alloc/remove
function and remove the __flow_block_indr_binding.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow_indr_block_cb_alloc/remove function for next fix patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-06-19
1) Fix double ESP trailer insertion in IPsec crypto offload if
netif_xmit_frozen_or_stopped is true. From Huy Nguyen.
2) Merge fixup for "remove output_finish indirection from
xfrm_state_afinfo". From Stephen Rothwell.
3) Select CRYPTO_SEQIV for ESP as this is needed for GCM and several
other encryption algorithms. Also modernize the crypto algorithm
selections for ESP and AH, remove those that are maked as "MUST NOT"
and add those that are marked as "MUST" be implemented in RFC 8221.
From Eric Biggers.
Please note the merge conflict between commit:
a7f7f6248d ("treewide: replace '---help---' in Kconfig files with 'help'")
from Linus' tree and commits:
7d4e391959 ("esp, ah: consolidate the crypto algorithm selections")
be01369859 ("esp, ah: modernize the crypto algorithm selections")
from the ipsec tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tlen field into struct tso_t, and change tso_start()
to return skb_transport_offset(skb) + tso->tlen
This removes from callers the need to use tcp_hdrlen(skb) and
will ease UDP segmentation offload addition.
v2: calls tso_start() earlier in otx2_sq_append_tso() [Jakub]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb argument of tso_count_descs(), tso_build_hdr() and tso_build_data() can be const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
size field can be an int, no need for size_t
Removes a 32bit hole on 64bit kernels.
And align fields for better readability.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transport header size could be 60 bytes, and network header
size can also be 60 bytes. Add the Ethernet header and we
are above 128 bytes.
Since drivers using net/core/tso.c usually allocates
one DMA coherent piece of memory per TX queue, this patch
might cause issues if a driver was using too many slots.
For 1024 slots, we would need 256 KB of physically
contiguous memory instead of 128 KB.
Alternative fix would be to add checks in the fast path,
but this involves more work in all drivers using net/core/tso.c.
Fixes: f9cbe9a556 ("net: define the TSO header size in net/tso.h")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_REMOVE_ADV_MONITOR command.
Note that the controller-based monitoring is not yet in place. This
removes the internal monitor(s) without sending HCI traffic, so the
request returns immediately.
The following test was performed.
- Issue btmgmt advmon-remove with valid and invalid handles.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_ADD_ADV_PATTERNS_MONITOR command.
Note that the controller-based monitoring is not yet in place. This tracks
the content of the monitor without sending HCI traffic, so the request
returns immediately.
The following manual test was performed.
- Issue btmgmt advmon-add with valid and invalid inputs.
- Issue btmgmt advmon-add more the allowed number of monitors.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to more easily add device flags to classic devices, create
a new type of bdaddr_list that supports setting flags.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently, nf_flow_table_offload_add/del_cb are exported by nf_flow_table
module, therefore modules using them will have hard-dependency
on nf_flow_table and will require loading it all the time.
This can lead to an unnecessary overhead on systems that do not
use this API.
To relax the hard-dependency between the modules, we unexport these
functions and make them static inline.
Fixes: 978703f425 ("netfilter: flowtable: Add API for registering to flow table events")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tcf_ct_flow_table_restore_skb is exported by act_ct
module, therefore modules using it will have hard-dependency
on act_ct and will require loading it all the time.
This can lead to an unnecessary overhead on systems that do not
use hardware connection tracking action (ct_metadata action) in
the first place.
To relax the hard-dependency between the modules, we unexport this
function and make it a static inline one.
Fixes: 30b0cf90c6 ("net/sched: act_ct: Support restoring conntrack info on skbs")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch submits the corresponding kernel definitions to mgmt.h.
This is submitted before the implementation to avoid any conflicts in
values allocations.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change implements suggestions from the code review of the SCO CMSG
state flag patch.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for reporting the BT_PKT_STATUS to the socket
CMSG data to allow the implementation of a packet loss correction on
erroneous data received on the SCO socket.
The patch was partially developed by Marcel Holtmann and validated by
Hsin-yu Chao.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull sysctl fixes from Al Viro:
"Fixups to regressions in sysctl series"
* 'work.sysctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sysctl: reject gigantic reads/write to sysctl files
cdrom: fix an incorrect __user annotation on cdrom_sysctl_info
trace: fix an incorrect __user annotation on stack_trace_sysctl
random: fix an incorrect __user annotation on proc_do_entropy
net/sysctl: remove leftover __user annotations on neigh_proc_dointvec*
net/sysctl: use cpumask_parse in flow_limit_cpu_sysctl
vxlan driver should be using helpers to access nexthop struct
internals. Remove open check if whether nexthop is multipath in
favor of the existing nexthop_is_multipath helper. Add a new
helper, nexthop_has_v4, to cover the need to check has_v4 in
a group.
Fixes: 1274e1cc42 ("vxlan: ecmp support for mac fdb entries")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb nexthops are marked with a flag. For standalone nexthops, a flag was
added to the nh_info struct. For groups that flag was added to struct
nexthop when it should have been added to the group information. Fix
by removing the flag from the nexthop struct and adding a flag to nh_group
that mirrors nh_info and is really only a caching of the individual types.
Add a helper, nexthop_is_fdb, for use by the vxlan code and fixup the
internal code to use the flag from either nh_info or nh_group.
v2
- propagate fdb_nh in remove_nh_grp_entry
Fixes: 38428d6871 ("nexthop: support for fdb ecmp nexthops")
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove function declarations that are not available in the tree anymore.
Fixes: 709ffbe19b ("net: remove indirect block netdev event registration")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some memory leaks in dccp_init() and dccp_fini().
In dccp_fini() and the error handling path in dccp_init(), free lhash2
is missing. Add inet_hashinfo2_free_mod() to do it.
If inet_hashinfo2_init_mod() failed in dccp_init(),
percpu_counter_destroy() should be called to destroy dccp_orphan_count.
It need to goto out_free_percpu when inet_hashinfo2_init_mod() failed.
Fixes: c92c81df93 ("net: dccp: fix kernel crash on module load")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix the deadlock on rfkill/wireless removal that a few
people reported
* fix an uninitialized variable
* update wiki URLs
-----BEGIN PGP SIGNATURE-----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=wP9I
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2020-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a small update:
* fix the deadlock on rfkill/wireless removal that a few
people reported
* fix an uninitialized variable
* update wiki URLs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the leftover __user annotation on the prototypes for
neigh_proc_dointvec*. The implementations already got this right, but
the headers kept the __user tags around.
Fixes: 32927393dc ("sysctl: pass kernel pointers to ->proc_handler")
Reported-by: build test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Lockdep reports that we may deadlock because we take the RTNL on
the work struct, but flush it under RTNL. Clearly, it's correct.
In practice, this can happen when doing rfkill on an active device.
Fix this by moving the work struct to the wiphy (registered dev)
layer, and iterate over all the wdevs inside there. This then
means we need to track which one of them has work to do, so we
don't update to the driver for all wdevs all the time.
Also fix a locking bug I noticed while working on this - the
registrations list is iterated as if it was an RCU list, but it
isn't handle that way - and we need to lock now for the update
flag anyway, so remove the RCU.
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Reported-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-and-tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200604120420.b1dc540a7e26.I55dcca56bb5bdc5d7ad66a36a0b42afd7034d8be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearing the 'inet_num' field is necessary and safe if and
only if the socket is not bound. The MPTCP protocol calls
the destroy helper on bound sockets, as tcp_v{4,6}_syn_recv_sock
completed successfully.
Move the clearing of such field out of the common code, otherwise
the MPTCP MP_JOIN error path will find the wrong 'inet_num' value
on socket disposal, __inet_put_port() will acquire the wrong lock
and bind_node removal could race with other modifiers possibly
corrupting the bind hash table.
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 729cd6436f ("mptcp: cope better with MP_JOIN failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seg6_validate_srh() is used to validate SRH for three cases:
case1: SRH of data-plane SRv6 packets to be processed by the Linux kernel.
Case2: SRH of the netlink message received from user-space (iproute2)
Case3: SRH injected into packets through setsockopt
In case1, the SRH can be encoded in the Reduced way (i.e., first SID is
carried in DA only and not represented as SID in the SRH) and the
seg6_validate_srh() now handles this case correctly.
In case2 and case3, the SRH shouldn’t be encoded in the Reduced way
otherwise we lose the first segment (i.e., the first hop).
The current implementation of the seg6_validate_srh() allow SRH of case2
and case3 to be encoded in the Reduced way. This leads a slab-out-of-bounds
problem.
This patch verifies SRH of case1, case2 and case3. Allowing case1 to be
reduced while preventing SRH of case2 and case3 from being reduced .
Reported-by: syzbot+e8c028b62439eac42073@syzkaller.appspotmail.com
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 0cb7498f23 ("seg6: fix SRH processing to comply with RFC8754")
Signed-off-by: Ahmed Abdelsalam <ahabdels@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During IPsec performance testing, we see bad ICMP checksum. The error packet
has duplicated ESP trailer due to double validate_xmit_xfrm calls. The first call
is from ip_output, but the packet cannot be sent because
netif_xmit_frozen_or_stopped is true and the packet gets dev_requeue_skb. The second
call is from NET_TX softirq. However after the first call, the packet already
has the ESP trailer.
Fix by marking the skb with XFRM_XMIT bit after the packet is handled by
validate_xmit_xfrm to avoid duplicate ESP trailer insertion.
Fixes: f6e27114a6 ("net: Add a xfrm validate function to validate_xmit_skb")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Pull uaccess/csum updates from Al Viro:
"Regularize the sitation with uaccess checksum primitives:
- fold csum_partial_... into csum_and_copy_..._user()
- on x86 collapse several access_ok()/stac()/clac() into
user_access_begin()/user_access_end()"
* 'uaccess.csum' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
default csum_and_copy_to_user(): don't bother with access_ok()
take the dummy csum_and_copy_from_user() into net/checksum.h
arm: switch to csum_and_copy_from_user()
sh32: convert to csum_and_copy_from_user()
m68k: convert to csum_and_copy_from_user()
xtensa: switch to providing csum_and_copy_from_user()
sparc: switch to providing csum_and_copy_from_user()
parisc: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
alpha: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: csum_partial_copy_nocheck(): don't abuse csum_partial_copy_from_user()
x86: switch 32bit csum_and_copy_to_user() to user_access_{begin,end}()
x86: switch both 32bit and 64bit to providing csum_and_copy_from_user()
x86_64: csum_..._copy_..._user(): switch to unsafe_..._user()
get rid of csum_partial_copy_to_user()
Extend bpf() syscall subcommands that operate on bpf_link, that is
LINK_CREATE, LINK_UPDATE, OBJ_GET_INFO, to accept attach types tied to
network namespaces (only flow dissector at the moment).
Link-based and prog-based attachment can be used interchangeably, but only
one can exist at a time. Attempts to attach a link when a prog is already
attached directly, and the other way around, will be met with -EEXIST.
Attempts to detach a program when link exists result in -EINVAL.
Attachment of multiple links of same attach type to one netns is not
supported with the intention to lift the restriction when a use-case
presents itself. Because of that link create returns -E2BIG when trying to
create another netns link, when one already exists.
Link-based attachments to netns don't keep a netns alive by holding a ref
to it. Instead links get auto-detached from netns when the latter is being
destroyed, using a pernet pre_exit callback.
When auto-detached, link lives in defunct state as long there are open FDs
for it. -ENOLINK is returned if a user tries to update a defunct link.
Because bpf_link to netns doesn't hold a ref to struct net, special care is
taken when releasing, updating, or filling link info. The netns might be
getting torn down when any of these link operations are in progress. That
is why auto-detach and update/release/fill_info are synchronized by the
same mutex. Also, link ops have to always check if auto-detach has not
happened yet and if netns is still alive (refcnt > 0).
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-5-jakub@cloudflare.com
Move functions to manage BPF programs attached to netns that are not
specific to flow dissector to a dedicated module named
bpf/net_namespace.c.
The set of functions will grow with the addition of bpf_link support for
netns attached programs. This patch prepares ground by creating a place
for it.
This is a code move with no functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-4-jakub@cloudflare.com
In order to:
(1) attach more than one BPF program type to netns, or
(2) support attaching BPF programs to netns with bpf_link, or
(3) support multi-prog attach points for netns
we will need to keep more state per netns than a single pointer like we
have now for BPF flow dissector program.
Prepare for the above by extracting netns_bpf that is part of struct net,
for storing all state related to BPF programs attached to netns.
Turn flow dissector callbacks for querying/attaching/detaching a program
into generic ones that operate on netns_bpf. Next patch will move the
generic callbacks into their own module.
This is similar to how it is organized for cgroup with cgroup_bpf.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200531082846.2117903-3-jakub@cloudflare.com
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
The sock_bindtoindex intended for kernel wide usage however
it will lock the socket regardless of the context. This modification
relax this behavior optionally: locking the socket will be optional
by calling the sock_bindtoindex with lock_sk = true.
The modification applied to all users of the sock_bindtoindex.
Signed-off-by: Ferenc Fejes <fejes@inf.elte.hu>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/bee6355da40d9e991b2f2d12b67d55ebb5f5b207.1590871065.git.fejes@inf.elte.hu
KTLS uses a stream parser to collect TLS messages and send them to
the upper layer tls receive handler. This ensures the tls receiver
has a full TLS header to parse when it is run. However, when a
socket has BPF_SK_SKB_STREAM_VERDICT program attached before KTLS
is enabled we end up with two stream parsers running on the same
socket.
The result is both try to run on the same socket. First the KTLS
stream parser runs and calls read_sock() which will tcp_read_sock
which in turn calls tcp_rcv_skb(). This dequeues the skb from the
sk_receive_queue. When this is done KTLS code then data_ready()
callback which because we stacked KTLS on top of the bpf stream
verdict program has been replaced with sk_psock_start_strp(). This
will in turn kick the stream parser again and eventually do the
same thing KTLS did above calling into tcp_rcv_skb() and dequeuing
a skb from the sk_receive_queue.
At this point the data stream is broke. Part of the stream was
handled by the KTLS side some other bytes may have been handled
by the BPF side. Generally this results in either missing data
or more likely a "Bad Message" complaint from the kTLS receive
handler as the BPF program steals some bytes meant to be in a
TLS header and/or the TLS header length is no longer correct.
We've already broke the idealized model where we can stack ULPs
in any order with generic callbacks on the TX side to handle this.
So in this patch we do the same thing but for RX side. We add
a sk_psock_strp_enabled() helper so TLS can learn a BPF verdict
program is running and add a tls_sw_has_ctx_rx() helper so BPF
side can learn there is a TLS ULP on the socket.
Then on BPF side we omit calling our stream parser to avoid
breaking the data stream for the KTLS receiver. Then on the
KTLS side we call BPF_SK_SKB_STREAM_VERDICT once the KTLS
receiver is done with the packet but before it posts the
msg to userspace. This gives us symmetry between the TX and
RX halfs and IMO makes it usable again. On the TX side we
process packets in this order BPF -> TLS -> TCP and on
the receive side in the reverse order TCP -> TLS -> BPF.
Discovered while testing OpenSSL 3.0 Alpha2.0 release.
Fixes: d829e9c411 ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/159079361946.5745.605854335665044485.stgit@john-Precision-5820-Tower
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add xdp_txq_info as the Tx counterpart to xdp_rxq_info. At the
moment only the device is added. Other fields (queue_index)
can be added as use cases arise.
>From a UAPI perspective, add egress_ifindex to xdp context for
bpf programs to see the Tx device.
Update the verifier to only allow accesses to egress_ifindex by
XDP programs with BPF_XDP_DEVMAP expected attach type.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200529220716.75383-4-dsahern@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps for packets that are sampled / trapped by ACLs, so that
capable drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 3 control packet traps such as ARP and DHCP, so that capable
device drivers could register them with devlink. Add documentation for
every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 2 control packet traps such as STP and IGMP query, so that
capable device drivers could register them with devlink. Add
documentation for every added packet trap and packet trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that hit exceptions during layer 3 forwarding must be trapped to
the CPU for the control plane to function properly. Create a dedicated
group for them, so that user space could choose to assign a different
policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next
to extend ctnetlink and the flowtable infrastructure:
1) Extend ctnetlink kernel side netlink dump filtering capabilities,
from Romain Bellan.
2) Generalise the flowtable hook parser to take a hook list.
3) Pass a hook list to the flowtable hook registration/unregistration.
4) Add a helper function to release the flowtable hook list.
5) Update the flowtable event notifier to pass a flowtable hook list.
6) Allow users to add new devices to an existing flowtables.
7) Allow users to remove devices to an existing flowtables.
8) Allow for registering a flowtable with no initial devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not register to netdev events to set up indirect blocks
anymore. Remove __flow_indr_block_cb_register() and
__flow_indr_block_cb_unregister().
The frontends set up the callbacks through flow_indr_dev_setup_block()
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices provide no dev->netdev_ops->ndo_setup_tc(...) interface.
The tunnel device and route control plane does not provide an obvious
way to relate tunnel and physical devices.
This patch allows drivers to register a tunnel device offload handler
for the tc and netfilter frontends through flow_indr_dev_register() and
flow_indr_dev_unregister().
The frontend calls flow_indr_dev_setup_offload() that iterates over the
list of drivers that are offering tunnel device hardware offload
support and it sets up the flow block for this tunnel device.
If the driver module is removed, the indirect flow_block ends up with a
stale callback reference. The module removal path triggers the
dev_shutdown() path to remove the qdisc and the flow_blocks for the
physical devices. However, this is not useful for tunnel devices, where
relation between the physical and the tunnel device is not explicit.
This patch introduces a cleanup callback that is invoked when the driver
module is removed to clean up the tunnel device flow_block. This patch
defines struct flow_block_indr and it uses it from flow_block_cb to
store the information that front-end requires to perform the
flow_block_cb cleanup on module removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function schedules the flow teardown state and it forces a gc run.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----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=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With some newer AKMs, the KCK and KEK are bigger, so allow that
if the driver advertises support for it. In addition, add a new
attribute for the AKM so we can use it for offloaded rekeying.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
[reword commit message]
Link: https://lore.kernel.org/r/20200528212237.5eb58b00a5d1.I61b09d77c4f382e8d58a05dcca78096e99a6bc15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These capabilities cover what would otherwise be transported
in HT/VHT capabilities, but only a subset thereof that is
actually needed on 6 GHz with HE already present. Expose the
capabilities to userspace, drivers are expected to set them
as using the 6 GHz band (currently) requires HE capability.
Link: https://lore.kernel.org/r/20200528213443.244cd5cb9db8.Icd8c773277a88c837e7e3af1d4d1013cc3b66543@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7R3wcACgkQSD+KveBX
+j6/ZQf/QD39naPeImfLjemkRK9L+TKbS4nU6wpUwf1jC33Wdm4HhkhsWEnR6C4l
OwU/Pae3I9EtKP4gRE0W1o8h7zC9h4hY7+IKZOdyQ32iUY55PX/H25oqAiCj1NCM
xzWpXOTwK/vkqmkCedAd+YpNdYlbOhfycr+KVPSsvFdaPqjzfNO1PJcLsUbAbzrX
A+8pYdhUYTtx1N3YHJL5abLN6WzMAKxgwlm9GG8YCXACTJT6CBWWHGebVsC5TDUk
Lj5hJj38mI8/3dcu6vWP0kLGVfRZo0HS/gpPGxbKQFpP+1uBYaRENAQONxkY++6S
GDPix7ccvN+yNMlON893PC/Cogw3Yg==
=WaCJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-cleanup-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mpls_entry_encode() from net/mpls/internal.h to include/net/mpls.h
and make it available for other users. Specifically, hardware driver that
offload MPLS can benefit from that.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As of commit 98fa6271cf
("tcp: refactor setting the initial congestion window") this is called
only from tcp_input.c, so it can be static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now that can be done conveniently - all non-trivial cases have
_HAVE_ARCH_COPY_AND_CSUM_FROM_USER defined, so the fallback in
net/checksum.h is used only for dummy (copy_from_user, then
csum_partial) implementation. Allowing us to get rid of all
dummy instances, both of csum_and_copy_from_user() and
csum_partial_copy_from_user().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The SCTP protocol allows to bind multiple address to a socket. That
feature is currently only exposed as a socket option. Add a bind_add
method struct proto that allows to bind additional addresses, and
switch the dlm code to use the method instead of going through the
socket option from kernel space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SCTP_NODELAY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-05-29
1) Several fixes for ESP gro/gso in transport and beet mode when
IPv6 extension headers are present. From Xin Long.
2) Fix a wrong comment on XFRMA_OFFLOAD_DEV.
From Antony Antony.
3) Fix sk_destruct callback handling on ESP in TCP encapsulation.
From Sabrina Dubroca.
4) Fix a use after free in xfrm_output_gso when used with vxlan.
From Xin Long.
5) Fix secpath handling of VTI when used wiuth IPCOMP.
From Xin Long.
6) Fix an oops when deleting a x-netns xfrm interface.
From Nicolas Dichtel.
7) Fix a possible warning on policy updates. We had a case where it was
possible to add two policies with the same lookup keys.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-05-29
1) Add IPv6 encapsulation support for ESP over UDP and TCP.
From Sabrina Dubroca.
2) Remove unneeded reference when initializing xfrm interfaces.
From Nicolas Dichtel.
3) Remove some indirect calls from the state_afinfo.
From Florian Westphal.
Please note that this pull request has two merge conflicts
between commit:
0c922a4850 ("xfrm: Always set XFRM_TRANSFORMED in xfrm{4,6}_output_finish")
from Linus' tree and commit:
2ab6096db2 ("xfrm: remove output_finish indirection from xfrm_state_afinfo")
from the ipsec-next tree.
and between commit:
3986912f6a ("ipv6: move SIOCADDRT and SIOCDELRT handling into ->compat_ioctl")
from the net-next tree and commit:
0146dca70b ("xfrm: add support for UDPv6 encapsulation of ESP")
from the ipsec-next tree.
Both conflicts can be resolved as done in linux-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the RXRPC_MIN_SECURITY_LEVEL sockopt from
kernel space without going through a fake uaccess.
Thanks to David Howells for the documentation updates.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_RECVPKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_ADD_PREFERENCES sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IPV6_V6ONLY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_PKTINFO sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_MTU_DISCOVER sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com> [rxrpc bits]
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_RECVERR sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_FREEBIND sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the IP_TOS sockopt from kernel space without
going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_REUSEPORT sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_RCVBUFFORCE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_KEEPALIVE sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly enable timestamps instead of setting the
SO_TIMESTAMP* sockopts from kernel space and going through a fake
uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_BINDTOIFINDEX sockopt from kernel
space without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_SNDTIMEO_NEW sockopt from kernel
space without going through a fake uaccess. The interface is
simplified to only pass the seconds value, as that is the only
thing needed at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_PRIORITY sockopt from kernel space
without going through a fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_LINGER sockopt from kernel space
with onoff set to true and a linger time of 0 without going through a
fake uaccess.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the SO_REUSEADDR sockopt from kernel space
without going through a fake uaccess.
For this the iscsi target now has to formally depend on inet to avoid
a mostly theoretical compile failure. For actual operation it already
did depend on having ipv4 or ipv6 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tcp_ld_RTO_revert() helper available to IPv6, and
implement RFC 6069 :
Quoting this RFC :
3. Connectivity Disruption Indication
For Internet Protocol version 6 (IPv6) [RFC2460], the counterpart of
the ICMP destination unreachable message of code 0 (net unreachable)
and of code 1 (host unreachable) is the ICMPv6 destination
unreachable message of code 0 (no route to destination) [RFC4443].
As with IPv4, a router should generate an ICMPv6 destination
unreachable message of code 0 in response to a packet that cannot be
delivered to its destination address because it lacks a matching
entry in its routing table.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
change typo in function name "nofity" to "notify"
sctp_ulpevent_nofity_peer_addr_change ->
sctp_ulpevent_notify_peer_addr_change
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a field to the tls rx offload context which enables
drivers to force a send_resync call.
This field can be used by drivers to request a resync at the next
possible tls record. It is beneficial for hardware that provides the
resync sequence number asynchronously. In such cases, the packet that
triggered the resync does not contain the information required for a
resync. Instead, the driver requests resync for all the following
TLS record until the asynchronous notification with the resync request
TCP sequence arrives.
A following series for mlx5e ConnectX-6DX TLS RX offload support will
use this mechanism.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conntrack dump does not support kernel side filtering (only get exists,
but it returns only one entry. And user has to give a full valid tuple)
It means that userspace has to implement filtering after receiving many
irrelevant entries, consuming resources (conntrack table is sometimes
very huge, much more than a routing table for example).
This patch adds filtering in kernel side. To achieve this goal, we:
* Add a new CTA_FILTER netlink attributes, actually a flag list to
parametize filtering
* Convert some *nlattr_to_tuple() functions, to allow a partial parsing
of CTA_TUPLE_ORIG and CTA_TUPLE_REPLY (so nf_conntrack_tuple it not
fully set)
Filtering is now possible on:
* IP SRC/DST values
* Ports for TCP and UDP flows
* IMCP(v6) codes types and IDs
Filtering is done as an "AND" operator. For example, when flags
PROTO_SRC_PORT, PROTO_NUM and IP_SRC are sets, only entries matching all
values are dumped.
Changes since v1:
Set NLM_F_DUMP_FILTERED in nlm flags if entries are filtered
Changes since v2:
Move several constants to nf_internals.h
Move a fix on netlink values check in a separate patch
Add a check on not-supported flags
Return EOPNOTSUPP if CDA_FILTER is set in ctnetlink_flush_conntrack
(not yet implemented)
Code style issues
Changes since v3:
Fix compilation warning reported by kbuild test robot
Changes since v4:
Fix a regression introduced in v3 (returned EINVAL for valid netlink
messages without CTA_MARK)
Changes since v5:
Change definition of CTA_FILTER_F_ALL
Fix a regression when CTA_TUPLE_ZONE is not set
Signed-off-by: Romain Bellan <romain.bellan@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support to configure per TID Tx Rate configuration
through NL80211_TID_CONFIG_ATTR_TX_RATE* attributes. And it uses
nl80211_parse_tx_bitrate_mask api to validate the Tx rate mask.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1589357504-10175-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the necessary capabilities in nl80211 to allow drivers to
assign a cookie to control port TX frames (returned via extack in
the netlink ACK message of the command) and then later report the
frame's status.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200508144202.7678-2-markus.theil@tu-ilmenau.de
[use extack cookie instead of explicit message, recombine patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185907.GA15102@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507183909.GA12993@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.
This doesn't actually change the nl80211 API yet.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
drop trace point name changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TIDs mask type is u64 in wiphy settings and nl80211 processing, see:
- wiphy TIDs mask sizes in tid_config_support structure
- prepare driver command in parse_tid_conf
Use the same type for TIDs mask in cfg80211_tid_cfg.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-2-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the last path, need to fix fib_info_nh_uses_dev for
external nexthops to avoid referencing multiple nh_grp structs.
Move the device check in fib_info_nh_uses_dev to a helper and
create a nexthop version that is called if the fib_info uses an
external nexthop.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIB lookups can return an entry that references an external nexthop.
While walking the nexthop struct we do not want to make multiple calls
into the nexthop code which can result in 2 different structs getting
accessed - one returning the number of paths the rest of the loop
seeing a different nh_grp struct. If the nexthop group shrunk, the
result is an attempt to access a fib_nh_common that does not exist for
the new nh_grp struct but did for the old one.
To fix that move the device evaluation code to a helper that can be
used for inline fib_nh path as well as external nexthops.
Update the existing check for fi->nh in fib_table_lookup to call a
new helper, nexthop_get_nhc_lookup, which walks the external nexthop
with a single rcu dereference.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got too fancy consolidating checks on multipath type. The result
is that path lookups can access 2 different nh_grp structs as exposed
by Nik's torture tests. Expand nexthop_is_multipath within nexthop.h to
avoid multiple, nh_grp dereferences and make decisions based on the
consistent struct.
Only 2 places left using nexthop_is_multipath are within IPv6, both
only check that the nexthop is a multipath for a branching decision
which are acceptable.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must avoid modifying published nexthop groups while they might be
in use, otherwise we might see NULL ptr dereferences. In order to do
that we allocate 2 nexthoup group structures upon nexthop creation
and swap between them when we have to delete an entry. The reason is
that we can't fail nexthop group removal, so we can't handle allocation
failure thus we move the extra allocation on creation where we can
safely fail and return ENOMEM.
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current MPLS dissector only parses the first MPLS Label Stack
Entry (second LSE can be parsed too, but only to set a key_id).
This patch adds the possibility to parse several LSEs by making
__skb_flow_dissect_mpls() return FLOW_DISSECT_RET_PROTO_AGAIN as long
as the Bottom Of Stack bit hasn't been seen, up to a maximum of
FLOW_DIS_MPLS_MAX entries.
FLOW_DIS_MPLS_MAX is arbitrarily set to 7. This should be enough for
many practical purposes, without wasting too much space.
To record the parsed values, flow_dissector_key_mpls is modified to
store an array of stack entries, instead of just the values of the
first one. A bit field, "used_lses", is also added to keep track of
the LSEs that have been set. The objective is to avoid defining a
new FLOW_DISSECTOR_KEY_MPLS_XX for each level of the MPLS stack.
TC flower is adapted for the new struct flow_dissector_key_mpls layout.
Matching on several MPLS Label Stack Entries will be added in the next
patch.
The NFP and MLX5 drivers are also adapted: nfp_flower_compile_mac() and
mlx5's parse_tunnel() now verify that the rule only uses the first LSE
and fail if it doesn't.
Finally, the behaviour of the FLOW_DISSECTOR_KEY_MPLS_ENTROPY key is
slightly modified. Instead of recording the first Entropy Label, it
now records the last one. This shouldn't have any consequences since
there doesn't seem to have any user of FLOW_DISSECTOR_KEY_MPLS_ENTROPY
in the tree. We'd probably better do a hash of all parsed MPLS labels
instead (excluding reserved labels) anyway. That'd give better entropy
and would probably also simplify the code. But that's not the purpose
of this patch, so I'm keeping that as a future possible improvement.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tls_sw_recvmsg() and tls_decrypt_done() can be run concurrently.
// tls_sw_recvmsg()
if (atomic_read(&ctx->decrypt_pending))
crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
else
reinit_completion(&ctx->async_wait.completion);
//tls_decrypt_done()
pending = atomic_dec_return(&ctx->decrypt_pending);
if (!pending && READ_ONCE(ctx->async_notify))
complete(&ctx->async_wait.completion);
Consider the scenario tls_decrypt_done() is about to run complete()
if (!pending && READ_ONCE(ctx->async_notify))
and tls_sw_recvmsg() reads decrypt_pending == 0, does reinit_completion(),
then tls_decrypt_done() runs complete(). This sequence of execution
results in wrong completion. Consequently, for next decrypt request,
it will not wait for completion, eventually on connection close, crypto
resources freed, there is no way to handle pending decrypt response.
This race condition can be avoided by having atomic_read() mutually
exclusive with atomic_dec_return(),complete().Intoduced spin lock to
ensure the mutual exclution.
Addressed similar problem in tx direction.
v1->v2:
- More readable commit message.
- Corrected the lock to fix new race scenario.
- Removed barrier which is not needed now.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes two updates and one cleanup patch
1) Tang Bim, clean-up with IS_ERR() usage
2) Vlad introduces a new mlx5 kconfig flag for TC support
This is required due to the high volume of current and upcoming
development in the eswitch and representors areas where some of the
feature are TC based such as the downstream patches of MPLSoUDP and
the following representor bonding support for VF live migration and
uplink representor dynamic loading.
For this Vlad kept TC specific code in tc.c and rep/tc.c and
organized non TC code in representors specific files.
3) Eli Cohen adds support for MPLS over UPD encap and decap TC offloads.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7IZFEACgkQSD+KveBX
+j7IEQf/RFv633bWTlL63fEJjViRv1rjfkbyaXrGVL3gzr/Er01DeAPR22CNOlC3
bu1jHLKqVn0Mg0g5g2B4/H/7JoFbMBRTy4MXpM5VrQCIqwMuXG4zhWuoUj7ncQ5w
kXHAU6DUuZRn8/x1JLQOHDRTzKhav7ldT+nvvoKEMrad/DEMGz+bq67xh4l8nfi+
ktSFAO0UFi9ysb25CMfdqIqAL0J5nAJ7DNhw5x7IvtwUxNxate7HtBaBhBgZ9NWv
jYf8R3p+7JdgvVW18pZhmjbaBqaApXcZrC7rI07PR6rCOAHfToX6miR8gUtpIEno
itQkzYt9UF2dgNwMmxoJLqnUNiy/Cg==
=wkSR
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-05-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-05-22
This series includes two updates and one cleanup patch
1) Tang Bim, clean-up with IS_ERR() usage
2) Vlad introduces a new mlx5 kconfig flag for TC support
This is required due to the high volume of current and upcoming
development in the eswitch and representors areas where some of the
feature are TC based such as the downstream patches of MPLSoUDP and
the following representor bonding support for VF live migration and
uplink representor dynamic loading.
For this Vlad kept TC specific code in tc.c and rep/tc.c and
organized non TC code in representors specific files.
3) Eli Cohen adds support for MPLS over UPD encap and decap TC offloads.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_is_bareudp() so the device can be identified as a bareudp one.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the variable mrp_ring_state from switchdev_attr because is not
used anywhere.
The ring state is set using SWITCHDEV_OBJ_ID_RING_STATE_MRP.
Fixes: c284b54590 ("switchdev: mrp: Extend switchdev API to offload MRP")
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=jJvy
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-fixes-20200520' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix retransmission timeout and ACK discard
Here are a couple of fixes and an extra tracepoint for AF_RXRPC:
(1) Calculate the RTO pretty much as TCP does, rather than making
something up, including an initial 4s timeout (which causes return
probes from the fileserver to fail if a packet goes missing), and add
backoff.
(2) Fix the discarding of out-of-order received ACKs. We mustn't let the
hard-ACK point regress, nor do we want to do unnecessary
retransmission because the soft-ACK list regresses. This is not
trivial, however, due to some loose wording in various old protocol
specs, the ACK field that should be used for this sometimes has the
wrong information in it.
(3) Add a tracepoint to log a discarded ACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make FLOW_ACTION_HW_STATS_DONT_CARE be all bits, rather than none, so that
drivers and __flow_action_hw_stats_check can use simple bitwise checks.
Pre-fill all actions with DONT_CARE in flow_rule_alloc(), rather than
relying on implicit semantics of zero from kzalloc, so that callers which
don't configure action stats themselves (i.e. netfilter) get the correct
behaviour by default.
Only the kernel's internal API semantics change; the TC uAPI is unaffected.
v4: move DONT_CARE setting to flow_rule_alloc() for robustness and simplicity.
v3: set DONT_CARE in nft and ct offload.
v2: rebased on net-next, removed RFC tags.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds nexthop add/del notifiers. To be used by
vxlan driver in a later patch. Could possibly be used by
switchdev drivers in the future.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Todays vxlan mac fdb entries can point to multiple remote
ips (rdsts) with the sole purpose of replicating
broadcast-multicast and unknown unicast packets to those remote ips.
E-VPN multihoming [1,2,3] requires bridged vxlan traffic to be
load balanced to remote switches (vteps) belonging to the
same multi-homed ethernet segment (E-VPN multihoming is analogous
to multi-homed LAG implementations, but with the inter-switch
peerlink replaced with a vxlan tunnel). In other words it needs
support for mac ecmp. Furthermore, for faster convergence, E-VPN
multihoming needs the ability to update fdb ecmp nexthops independent
of the fdb entries.
New route nexthop API is perfect for this usecase.
This patch extends the vxlan fdb code to take a nexthop id
pointing to an ecmp nexthop group.
Changes include:
- New NDA_NH_ID attribute for fdbs
- Use the newly added fdb nexthop groups
- makes vxlan rdsts and nexthop handling code mutually
exclusive
- since this is a new use-case and the requirement is for ecmp
nexthop groups, the fdb add and update path checks that the
nexthop is really an ecmp nexthop group. This check can be relaxed
in the future, if we want to introduce replication fdb nexthop groups
and allow its use in lieu of current rdst lists.
- fdb update requests with nexthop id's only allowed for existing
fdb's that have nexthop id's
- learning will not override an existing fdb entry with nexthop
group
- I have wrapped the switchdev offload code around the presence of
rdst
[1] E-VPN RFC https://tools.ietf.org/html/rfc7432
[2] E-VPN with vxlan https://tools.ietf.org/html/rfc8365
[3] http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
Includes a null check fix in vxlan_xmit from Nikolay
v2 - Fixed build issue:
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ecmp nexthops and nexthop groups
for mac fdb entries. In subsequent patches this is used
by the vxlan driver fdb entries. The use case is
E-VPN multihoming [1,2,3] which requires bridged vxlan traffic
to be load balanced to remote switches (vteps) belonging to
the same multi-homed ethernet segment (This is analogous to
a multi-homed LAG but over vxlan).
Changes include new nexthop flag NHA_FDB for nexthops
referenced by fdb entries. These nexthops only have ip.
This patch includes appropriate checks to avoid routes
referencing such nexthops.
example:
$ip nexthop add id 12 via 172.16.1.2 fdb
$ip nexthop add id 13 via 172.16.1.3 fdb
$ip nexthop add id 102 group 12/13 fdb
$bridge fdb add 02:02:00:00:00:13 dev vxlan1000 nhid 101 self
[1] E-VPN https://tools.ietf.org/html/rfc7432
[2] E-VPN VxLAN: https://tools.ietf.org/html/rfc8365
[3] LPC talk with mention of nexthop groups for L2 ecmp
http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
v4 - fixed uninitialized variable reported by kernel test robot
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce the number of function calls, the struct
xsk_buff_pool definition is moved to xsk_buff_pool.h. The functions
xp_get_dma(), xp_dma_sync_for_cpu(), xp_dma_sync_for_device(),
xp_validate_desc() and various helper functions are explicitly
inlined.
Further, move xp_get_handle() and xp_release() to xsk.c, to allow for
the compiler to perform inlining.
rfc->v1: Make sure xp_validate_desc() is inlined for Tx perf. (Maxim)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-15-bjorn.topel@gmail.com
There are no users of MEM_TYPE_ZERO_COPY. Remove all corresponding
code, including the "handle" member of struct xdp_buff.
rfc->v1: Fixed spelling in commit message. (Björn)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-13-bjorn.topel@gmail.com
In order to simplify AF_XDP zero-copy enablement for NIC driver
developers, a new AF_XDP buffer allocation API is added. The
implementation is based on a single core (single producer/consumer)
buffer pool for the AF_XDP UMEM.
A buffer is allocated using the xsk_buff_alloc() function, and
returned using xsk_buff_free(). If a buffer is disassociated with the
pool, e.g. when a buffer is passed to an AF_XDP socket, a buffer is
said to be released. Currently, the release function is only used by
the AF_XDP internals and not visible to the driver.
Drivers using this API should register the XDP memory model with the
new MEM_TYPE_XSK_BUFF_POOL type.
The API is defined in net/xdp_sock_drv.h.
The buffer type is struct xdp_buff, and follows the lifetime of
regular xdp_buffs, i.e. the lifetime of an xdp_buff is restricted to
a NAPI context. In other words, the API is not replacing xdp_frames.
In addition to introducing the API and implementations, the AF_XDP
core is migrated to use the new APIs.
rfc->v1: Fixed build errors/warnings for m68k and riscv. (kbuild test
robot)
Added headroom/chunk size getter. (Maxim/Björn)
v1->v2: Swapped SoBs. (Maxim)
v2->v3: Initialize struct xdp_buff member frame_sz. (Björn)
Add API to query the DMA address of a frame. (Maxim)
Do DMA sync for CPU till the end of the frame to handle
possible growth (frame_sz). (Maxim)
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-6-bjorn.topel@gmail.com
Move the XSK_NEXT_PG_CONTIG_{MASK,SHIFT}, and
XDP_UMEM_USES_NEED_WAKEUP defines from xdp_sock.h to the AF_XDP
internal xsk.h file. Also, start using the BIT{,_ULL} macro instead of
explicit shifts.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-5-bjorn.topel@gmail.com
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
The XSKMAP is partly implemented by net/xdp/xsk.c. Move xskmap.c from
kernel/bpf/ to net/xdp/, which is the logical place for AF_XDP related
code. Also, move AF_XDP struct definitions, and function declarations
only used by AF_XDP internals into net/xdp/xsk.h.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-3-bjorn.topel@gmail.com
Calculating the "data_hard_end" for an XDP buffer coming from AF_XDP
zero-copy mode, the return value of xsk_umem_xdp_frame_sz() is added
to "data_hard_start".
Currently, the chunk size of the UMEM is returned by
xsk_umem_xdp_frame_sz(). This is not correct, if the fixed UMEM
headroom is non-zero. Fix this by returning the chunk_size without the
UMEM headroom.
Fixes: 2a637c5b1a ("xdp: For Intel AF_XDP drivers add XDP frame_sz")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-2-bjorn.topel@gmail.com
In case we can't find a ->dumpit callback for the requested
(family,type) pair, we fall back to (PF_UNSPEC,type). In effect, we're
in the same situation as if userspace had requested a PF_UNSPEC
dump. For RTM_GETROUTE, that handler is rtnl_dump_all, which calls all
the registered RTM_GETROUTE handlers.
The requested table id may or may not exist for all of those
families. commit ae677bbb44 ("net: Don't return invalid table id
error when dumping all families") fixed the problem when userspace
explicitly requests a PF_UNSPEC dump, but missed the fallback case.
For example, when we pass ipv6.disable=1 to a kernel with
CONFIG_IP_MROUTE=y and CONFIG_IP_MROUTE_MULTIPLE_TABLES=y,
the (PF_INET6, RTM_GETROUTE) handler isn't registered, so we end up in
rtnl_dump_all, and listing IPv6 routes will unexpectedly print:
# ip -6 r
Error: ipv4: MR table does not exist.
Dump terminated
commit ae677bbb44 introduced the dump_all_families variable, which
gets set when userspace requests a PF_UNSPEC dump. However, we can't
simply set the family to PF_UNSPEC in rtnetlink_rcv_msg in the
fallback case to get dump_all_families == true, because some messages
types (for example RTM_GETRULE and RTM_GETNEIGH) only register the
PF_UNSPEC handler and use the family to filter in the kernel what is
dumped to userspace. We would then export more entries, that userspace
would have to filter. iproute does that, but other programs may not.
Instead, this patch removes dump_all_families and updates the
RTM_GETROUTE handlers to check if the family that is being dumped is
their own. When it's not, which covers both the intentional PF_UNSPEC
dumps (as dump_all_families did) and the fallback case, ignore the
missing table id error.
Fixes: cb167893f4 ("net: Plumb support for filtering ipv4 and ipv6 multicast route dumps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now we can do MCAST_MSFILTER in compat ->getsockopt() without
playing silly buggers with copying things back and forth.
We can form a native struct group_filter (sans the variable-length
tail) on stack, pass that + pointer to the tail of original request
to the helper doing the bulk of the work, then do the rest of
copyout - same as the native getsockopt() does.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pass the userland pointer to the array in its tail, so that part
gets copied out by our functions; copyout of everything else is
done in the callers. Rationale: reuse for compat; the array
is the same in native and compat, the layout of parts before it
is different for compat.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We want to get rid of compat_mc_[sg]etsockopt() and to have that stuff
handled without compat_alloc_user_space(), extra copying through
userland, etc. To do that we'll need ipv4 and ipv6 instances of
->compat_[sg]etsockopt() to manipulate the 32bit variants of mcast
requests, so we need to move the definitions of those out of net/compat.c
and into a public header.
This patch just does a mechanical move to include/net/compat.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This method is used to properly allow kernel callers of the IPv4 route
management ioctls. The exsting ip_tunnel_ioctl helper is renamed to
ip_tunnel_ctl to better reflect that it doesn't directly implement ioctls
touching user memory, and is used for the guts of ndo_tunnel_ctl
implementations. A new ip_tunnel_ioctl helper is added that can be wired
up directly to the ndo_do_ioctl method and takes care of the copy to and
from userspace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of forward declarations (trivially shifting code around
where needed), and make a few functions static.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare removing the global routing_ioctl hack start lifting the code
into the ipv4 and appletalk ->compat_ioctl handlers. Unlike the existing
handler we don't bother copying in the name - there are no compat issues for
char arrays.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare removing the global routing_ioctl hack start lifting the code
into a newly added ipv6 ->compat_ioctl handler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for better compat ioctl handling by moving the user copy out
of ipv6_route_ioctl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new action is installed, firstuse field of 'tcf_t' is explicitly set
to 0. Value of zero means "new action, not yet used"; as a packet hits the
action, 'firstuse' is stamped with the current jiffies value.
tcf_tm_dump() should return 0 for firstuse if action has not yet been hit.
Fixes: 48d8ee1694 ("net sched actions: aggregate dumping of actions timeinfo")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RFC8684 allows to send 32-bit DATA_ACKs as long as the peer is not
sending 64-bit data-sequence numbers. The 64-bit DSN is only there for
extreme scenarios when a very high throughput subflow is combined with a
long-RTT subflow such that the high-throughput subflow wraps around the
32-bit sequence number space within an RTT of the high-RTT subflow.
It is thus a rare scenario and we should try to use the 32-bit DATA_ACK
instead as long as possible. It allows to reduce the TCP-option overhead
by 4 bytes, thus makes space for an additional SACK-block. It also makes
tcpdumps much easier to read when the DSN and DATA_ACK are both either
32 or 64-bit.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the steps to prepare an inet_connection_sock for
forced disposal inside a separate helper. No functional
changes inteded, this will just simplify the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MP_JOIN subflows must not land into the accept queue.
Currently tcp_check_req() calls an mptcp specific helper
to detect such scenario.
Such helper leverages the subflow context to check for
MP_JOIN subflows. We need to deal also with MP JOIN
failures, even when the subflow context is not available
due allocation failure.
A possible solution would be changing the syn_recv_sock()
signature to allow returning a more descriptive action/
error code and deal with that in tcp_check_req().
Since the above need is MPTCP specific, this patch instead
uses a TCP request socket hole to add a MPTCP specific flag.
Such flag is used by the MPTCP syn_recv_sock() to tell
tcp_check_req() how to deal with the request socket.
This change is a no-op for !MPTCP build, and makes the
MPTCP code simpler. It allows also the next patch to deal
correctly with MP JOIN failure.
v1 -> v2:
- be more conservative on drop_req initialization (Mat)
RFC -> v1:
- move the drop_req bit inside tcp_request_sock (Eric)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-15
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 1 day(s) which contain
a total of 67 files changed, 741 insertions(+), 252 deletions(-).
The main changes are:
1) bpf_xdp_adjust_tail() now allows to grow the tail as well, from Jesper.
2) bpftool can probe CONFIG_HZ, from Daniel.
3) CAP_BPF is introduced to isolate user processes that use BPF infra and
to secure BPF networking services by dropping CAP_SYS_ADMIN requirement
in certain cases, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcf_action_dump() with boolean argument 'terse' that is used to
request terse-mode action dump. In terse mode only essential data needed to
identify particular action (action kind, cookie, etc.) and its stats is put
to resulting skb and everything else is omitted. Implement
tcf_exts_terse_dump() helper in cls API that is intended to be used to
request terse dump of all exts (actions) attached to the filter.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new TCA_DUMP_FLAGS attribute and use it in cls API to request terse
filter output from classifiers with TCA_DUMP_FLAGS_TERSE flag. This option
is intended to be used to improve performance of TC filter dump when
userland only needs to obtain stats and not the whole classifier/action
data. Extend struct tcf_proto_ops with new terse_dump() callback that must
be defined by supporting classifier implementations.
Support of the options in specific classifiers and actions is
implemented in following patches in the series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel drivers implement native AF_XDP zerocopy in separate C-files,
that have its own invocation of bpf_prog_run_xdp(). The setup of
xdp_buff is also handled in separately from normal code path.
This patch update XDP frame_sz for AF_XDP zerocopy drivers i40e, ice
and ixgbe, as the code changes needed are very similar. Introduce a
helper function xsk_umem_xdp_frame_sz() for calculating frame size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/158945347511.97035.8536753731329475655.stgit@firesoul
Use hole in struct xdp_frame, when adding member frame_sz, which keeps
same sizeof struct (32 bytes)
Drivers ixgbe and sfc had bug cases where the necessary/expected
tailroom was not reserved. This can lead to some hard to catch memory
corruption issues. Having the drivers frame_sz this can be detected when
packet length/end via xdp->data_end exceed the xdp_data_hard_end
pointer, which accounts for the reserved the tailroom.
When detecting this driver issue, simply fail the conversion with NULL,
which results in feedback to driver (failing xdp_do_redirect()) causing
driver to drop packet. Given the lack of consistent XDP stats, this can
be hard to troubleshoot. And given this is a driver bug, we want to
generate some more noise in form of a WARN stack dump (to ID the driver
code that inlined convert_to_xdp_frame).
Inlining the WARN macro is problematic, because it adds an asm
instruction (on Intel CPUs ud2) what influence instruction cache
prefetching. Thus, introduce xdp_warn and macro XDP_WARN, to avoid this
and at the same time make identifying the function and line of this
inlined function easier.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945337313.97035.10015729316710496600.stgit@firesoul
XDP have evolved to support several frame sizes, but xdp_buff was not
updated with this information. The frame size (frame_sz) member of
xdp_buff is introduced to know the real size of the memory the frame is
delivered in.
When introducing this also make it clear that some tailroom is
reserved/required when creating SKBs using build_skb().
It would also have been an option to introduce a pointer to
data_hard_end (with reserved offset). The advantage with frame_sz is
that (like rxq) drivers only need to setup/assign this value once per
NAPI cycle. Due to XDP-generic (and some drivers) it's not possible to
store frame_sz inside xdp_rxq_info, because it's varies per packet as it
can be based/depend on packet length.
V2: nitpick: deduct -> deduce
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945334261.97035.555255657490688547.stgit@firesoul
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-14
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Merged tag 'perf-for-bpf-2020-05-06' from tip tree that includes CAP_PERFMON.
2) support for narrow loads in bpf_sock_addr progs and additional
helpers in cg-skb progs, from Andrey.
3) bpf benchmark runner, from Andrii.
4) arm and riscv JIT optimizations, from Luke.
5) bpf iterator infrastructure, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix gcc-10 compilation warning in nf_conntrack, from Arnd Bergmann.
2) Add NF_FLOW_HW_PENDING to avoid races between stats and deletion
commands, from Paul Blakey.
3) Remove WQ_MEM_RECLAIM from the offload workqueue, from Roi Dayan.
4) Infinite loop when removing nf_conntrack module, from Florian Westphal.
5) Set NF_FLOW_TEARDOWN bit on expiration to avoid races when refreshing
the timeout from the software path.
6) Missing nft_set_elem_expired() check in the rbtree, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL
support") adds a field btf_id_or_null_non0_off to
bpf_prog->aux structure to indicate that the
first ctx argument is PTR_TO_BTF_ID reg_type and
all others are PTR_TO_BTF_ID_OR_NULL.
This approach does not really scale if we have
other different reg types in the future, e.g.,
a pointer to a buffer.
This patch enables bpf_iter targets registering ctx argument
reg types which may be different from the default one.
For example, for pointers to structures, the default reg_type
is PTR_TO_BTF_ID for tracing program. The target can register
a particular pointer type as PTR_TO_BTF_ID_OR_NULL which can
be used by the verifier to enforce accesses.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180221.2949882-1-yhs@fb.com
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-05-13
Here's a second attempt at a bluetooth-next pull request which
supercedes the one dated 2020-05-09. This should have the issues
discovered by Jakub fixed.
- Add support for Intel Typhoon Peak device (8087:0032)
- Add device tree bindings for Realtek RTL8723BS device
- Add device tree bindings for Qualcomm QCA9377 device
- Add support for experimental features configuration through mgmt
- Add driver hook to prevent wake from suspend
- Add support for waiting for L2CAP disconnection response
- Multiple fixes & cleanups to the btbcm driver
- Add support for LE scatternet topology for selected devices
- A few other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Let drivers have a hook to disable configuring scanning during suspend.
Drivers should use the device_may_wakeup function call to determine
whether hci should be configured for wakeup.
For example, an implementation for btusb may look like the following:
bool btusb_prevent_wake(struct hci_dev *hdev)
{
struct btusb_data *data = hci_get_drvdata(hdev);
return !device_may_wakeup(&data->udev->dev);
}
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Provide an option that drivers can set to indicate they want to receive
vlan configuration even when vlan filtering is disabled. At the very
least, this is safe for Marvell DSA bridges, which do not look up
ingress traffic in the VTU if the port is in 8021Q disabled state. It is
also safe for the Ocelot switch family. Whether this change is suitable
for all DSA bridges is not known.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We autotune rcvbuf whenever SO_RCVLOWAT is set to account for 100%
overhead in tcp_set_rcvlowat()
This works well when skb->len/skb->truesize ratio is bigger than 0.5
But if we receive packets with small MSS, we can end up in a situation
where not enough bytes are available in the receive queue to satisfy
RCVLOWAT setting.
As our sk_rcvbuf limit is hit, we send zero windows in ACK packets,
preventing remote peer from sending more data.
Even autotuning does not help, because it only triggers at the time
user process drains the queue. If no EPOLLIN is generated, this
can not happen.
Note poll() has a similar issue, after commit
c7004482e8 ("tcp: Respect SO_RCVLOWAT in tcp_poll().")
Fixes: 03f45c883c ("tcp: avoid extra wakeups for SO_RCVLOWAT users")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc currently uses a fixed 4s retransmission timeout until the RTT is
sufficiently sampled. This can cause problems with some fileservers with
calls to the cache manager in the afs filesystem being dropped from the
fileserver because a packet goes missing and the retransmission timeout is
greater than the call expiry timeout.
Fix this by:
(1) Copying the RTT/RTO calculation code from Linux's TCP implementation
and altering it to fit rxrpc.
(2) Altering the various users of the RTT to make use of the new SRTT
value.
(3) Replacing the use of rxrpc_resend_timeout to use the calculated RTO
value instead (which is needed in jiffies), along with a backoff.
Notes:
(1) rxrpc provides RTT samples by matching the serial numbers on outgoing
DATA packets that have the RXRPC_REQUEST_ACK set and PING ACK packets
against the reference serial number in incoming REQUESTED ACK and
PING-RESPONSE ACK packets.
(2) Each packet that is transmitted on an rxrpc connection gets a new
per-connection serial number, even for retransmissions, so an ACK can
be cross-referenced to a specific trigger packet. This allows RTT
information to be drawn from retransmitted DATA packets also.
(3) rxrpc maintains the RTT/RTO state on the rxrpc_peer record rather than
on an rxrpc_call because many RPC calls won't live long enough to
generate more than one sample.
(4) The calculated SRTT value is in units of 8ths of a microsecond rather
than nanoseconds.
The (S)RTT and RTO values are displayed in /proc/net/rxrpc/peers.
Fixes: 17926a7932 ([AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both"")
Signed-off-by: David Howells <dhowells@redhat.com>
Gc step can queue offloaded flow del work or stats work.
Those work items can race each other and a flow could be freed
before the stats work is executed and querying it.
To avoid that, add a pending bit that if a work exists for a flow
don't queue another work for it.
This will also avoid adding multiple stats works in case stats work
didn't complete but gc step started again.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In case dynamic debug is disabled, this feature allows a vendor platform
to provide debug statement printing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When setting HCI_MGMT_HDEV_OPTIONAL it is possible to target a specific
conntroller or a global interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Somewhat similar to dsa_tree_find, dsa_switch_find returns a dsa_switch
structure pointer by searching for its tree index and switch index (the
parameters from dsa,member). To be used, for example, by drivers who
implement .crosschip_bridge_join and need a reference to the other
switch indicated to by the tree_index and sw_index arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 8db0a2ee2c ("net: bridge: reject DSA-enabled master netdevices
as bridge members") added a special check in br_if.c in order to check
for a DSA master network device with a tagging protocol configured. This
was done because back then, such devices, once enslaved in a bridge
would become inoperative and would not pass DSA tagged traffic anymore
due to br_handle_frame returning RX_HANDLER_CONSUMED.
But right now we have valid use cases which do require bridging of DSA
masters. One such example is when the DSA master ports are DSA switch
ports themselves (in a disjoint tree setup). This should be completely
equivalent, functionally speaking, from having multiple DSA switches
hanging off of the ports of a switchdev driver. So we should allow the
enslaving of DSA tagged master network devices.
Instead of the regular br_handle_frame(), install a new function
br_handle_frame_dummy() on these DSA masters, which returns
RX_HANDLER_PASS in order to call into the DSA specific tagging protocol
handlers, and lift the restriction from br_add_if.
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gcc-10 warns around a suspicious access to an empty struct member:
net/netfilter/nf_conntrack_core.c: In function '__nf_conntrack_alloc':
net/netfilter/nf_conntrack_core.c:1522:9: warning: array subscript 0 is outside the bounds of an interior zero-length array 'u8[0]' {aka 'unsigned char[0]'} [-Wzero-length-bounds]
1522 | memset(&ct->__nfct_init_offset[0], 0,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from net/netfilter/nf_conntrack_core.c:37:
include/net/netfilter/nf_conntrack.h:90:5: note: while referencing '__nfct_init_offset'
90 | u8 __nfct_init_offset[0];
| ^~~~~~~~~~~~~~~~~~
The code is correct but a bit unusual. Rework it slightly in a way that
does not trigger the warning, using an empty struct instead of an empty
array. There are probably more elegant ways to do this, but this is the
smallest change.
Fixes: c41884ce05 ("netfilter: conntrack: avoid zeroing timer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This merge includes updates to bonding driver needed for the rdma stack,
to avoid conflicts with the RDMA branch.
Maor Gottlieb Says:
====================
Bonding: Add support to get xmit slave
The following series adds support to get the LAG master xmit slave by
introducing new .ndo - ndo_get_xmit_slave. Every LAG module can
implement it and it first implemented in the bond driver.
This is follow-up to the RFC discussion [1].
The main motivation for doing this is for drivers that offload part
of the LAG functionality. For example, Mellanox Connect-X hardware
implements RoCE LAG which selects the TX affinity when the resources
are created and port is remapped when it goes down.
The first part of this patchset introduces the new .ndo and add the
support to the bonding module.
The second part adds support to get the RoCE LAG xmit slave by building
skb of the RoCE packet based on the AH attributes and call to the new
.ndo.
The third part change the mlx5 driver driver to set the QP's affinity
port according to the slave which found by the .ndo.
====================
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
percpu_counter_add() uses a default batch size which is quite big
on platforms with 256 cpus. (2*256 -> 512)
This means dst_entries_get_fast() can be off by +/- 2*(nr_cpus^2)
(131072 on servers with 256 cpus)
Reduce the batch size to something more reasonable, and
add logic to ip6_dst_gc() to call dst_entries_get_slow()
before calling the _very_ expensive fib6_run_gc() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to have a tighter control on what ports we bind to in
the BPF_CGROUP_INET{4,6}_CONNECT hooks even if it means
connect() becomes slightly more expensive. The expensive part
comes from the fact that we now need to call inet_csk_get_port()
that verifies that the port is not used and allocates an entry
in the hash table for it.
Since we can't rely on "snum || !bind_address_no_port" to prevent
us from calling POST_BIND hook anymore, let's add another bind flag
to indicate that the call site is BPF program.
v5:
* fix wrong AF_INET (should be AF_INET6) in the bpf program for v6
v3:
* More bpf_bind documentation refinements (Martin KaFai Lau)
* Add UDP tests as well (Martin KaFai Lau)
* Don't start the thread, just do socket+bind+listen (Martin KaFai Lau)
v2:
* Update documentation (Andrey Ignatov)
* Pass BIND_FORCE_ADDRESS_NO_PORT conditionally (Andrey Ignatov)
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200508174611.228805-5-sdf@google.com
The intent is to add an additional bind parameter in the next commit.
Instead of adding another argument, let's convert all existing
flag arguments into an extendable bit field.
No functional changes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200508174611.228805-4-sdf@google.com
<linux/cryptohash.h> sounds very generic and important, like it's the
header to include if you're doing cryptographic hashing in the kernel.
But actually it only includes the library implementation of the SHA-1
compression function (not even the full SHA-1). This should basically
never be used anymore; SHA-1 is no longer considered secure, and there
are much better ways to do cryptographic hashing in the kernel.
Most files that include this header don't actually need it. So in
preparation for removing it, remove all these unneeded includes of it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, bonding always returns NETDEV_TX_OK to its caller.
It is worth trying to be more accurate : TCP for instance
can have different recovery strategies if it can have more
precise status, if packet was dropped by slave qdisc.
This is especially important when host is under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As its implementation shows, this is synonimous with calling
dsa_slave_dev_check followed by dsa_slave_to_port, so it is quite simple
already and provides functionality which is already there.
However there is now a need for these functions outside dsa_priv.h, for
example in drivers that perform mirroring and redirection through
tc-flower offloads (they are given raw access to the flow_cls_offload
structure), where they need to call this function on act->dev.
But simply exporting dsa_slave_to_port would make it non-inline and
would result in an extra function call in the hotpath, as can be seen
for example in sja1105:
Before:
000006dc <sja1105_xmit>:
{
6dc: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e0: e1a04000 mov r4, r0
6e4: e591958c ldr r9, [r1, #1420] ; 0x58c <- Inline dsa_slave_to_port
6e8: e1a05001 mov r5, r1
6ec: e24dd004 sub sp, sp, #4
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6f0: e1c901d8 ldrd r0, [r9, #24]
6f4: ebfffffe bl 0 <dsa_8021q_tx_vid>
6f4: R_ARM_CALL dsa_8021q_tx_vid
u8 pcp = netdev_txq_to_tc(netdev, queue_mapping);
6f8: e1d416b0 ldrh r1, [r4, #96] ; 0x60
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6fc: e1a08000 mov r8, r0
After:
000006e4 <sja1105_xmit>:
{
6e4: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e8: e1a04000 mov r4, r0
6ec: e24dd004 sub sp, sp, #4
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f0: e1a00001 mov r0, r1
{
6f4: e1a05001 mov r5, r1
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f8: ebfffffe bl 0 <dsa_slave_to_port>
6f8: R_ARM_CALL dsa_slave_to_port
6fc: e1a09000 mov r9, r0
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
700: e1c001d8 ldrd r0, [r0, #24]
704: ebfffffe bl 0 <dsa_8021q_tx_vid>
704: R_ARM_CALL dsa_8021q_tx_vid
Because we want to avoid possible performance regressions, introduce
this new function which is designed to be public.
Suggested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang points out that building without IPv6 would lead to returning
an uninitialized variable if a packet with family!=AF_INET is
passed into bareudp_udp_encap_recv():
drivers/net/bareudp.c:139:6: error: variable 'err' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (family == AF_INET)
^~~~~~~~~~~~~~~~~
drivers/net/bareudp.c:146:15: note: uninitialized use occurs here
if (unlikely(err)) {
^~~
include/linux/compiler.h:78:42: note: expanded from macro 'unlikely'
# define unlikely(x) __builtin_expect(!!(x), 0)
^
drivers/net/bareudp.c:139:2: note: remove the 'if' if its condition is always true
if (family == AF_INET)
^~~~~~~~~~~~~~~~~~~~~~
This cannot happen in practice, so change the condition in a way that
gcc sees the IPv4 case as unconditionally true here.
For consistency, change all the similar constructs in this file the
same way, using "if(IS_ENABLED())" instead of #if IS_ENABLED()".
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it doesn't actually exist...
Test: builds and 'git grep tcp_default_init_rwnd' comes up empty
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FLOW_ACTION_HW_STATS_DONT_CARE which tells the driver
that the frontend does not need counters, this hw stats type request
never fails. The FLOW_ACTION_HW_STATS_DISABLED type explicitly requests
the driver to disable the stats, however, if the driver cannot disable
counters, it bails out.
TCA_ACT_HW_STATS_* maintains the 1:1 mapping with FLOW_ACTION_HW_STATS_*
except by disabled which is mapped to FLOW_ACTION_HW_STATS_DISABLED
(this is 0 in tc). Add tc_act_hw_stats() to perform the mapping between
TCA_ACT_HW_STATS_* and FLOW_ACTION_HW_STATS_*.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of horizon feature to sch_fq, we noticed some
suboptimal behavior of extremely low pacing rate TCP flows, especially
when TCP is not aware of a drop happening in lower stacks.
Back in commit 3f80e08f40 ("tcp: add tcp_reset_xmit_timer() helper"),
tcp_pacing_delay() was added to estimate an extra delay to add to standard
rto timers.
This patch removes the skb argument from this helper and
tcp_reset_xmit_timer() because it makes more sense to simply
consider the time at which next packet is allowed to be sent,
instead of the time of whatever packet has been sent.
This avoids arming RTO timer too soon and removes
spurious horizon drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the upcoming rev of RFC4941 (IPv6 temporary addresses):
https://tools.ietf.org/html/draft-ietf-6man-rfc4941bis-09
* Reduces the default Valid Lifetime to 2 days
The number of extra addresses employed when Valid Lifetime was
7 days exacerbated the stress caused on network
elements/devices. Additionally, the motivation for temporary
addresses is indeed privacy and reduced exposure. With a
default Valid Lifetime of 7 days, an address that becomes
revealed by active communication is reachable and exposed for
one whole week. The only use case for a Valid Lifetime of 7
days could be some application that is expecting to have long
lived connections. But if you want to have a long lived
connections, you shouldn't be using a temporary address in the
first place. Additionally, in the era of mobile devices, general
applications should nevertheless be prepared and robust to
address changes (e.g. nodes swap wifi <-> 4G, etc.)
* Employs different IIDs for different prefixes
To avoid network activity correlation among addresses configured
for different prefixes
* Uses a simpler algorithm for IID generation
No need to store "history" anywhere
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only two implementaions, one for ipv4 and one for ipv6.
Both are almost identical, they clear skb->cb[], set the TRANSFORMED flag
in IP(6)CB and then call the common xfrm_output() function.
By placing the IPCB handling into the common function, we avoid the need
for the output_finish indirection as the output functions can simply
use xfrm_output().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Move this to xfrm_output.c. This avoids the state->extract_output
indirection.
This patch also removes the duplicated __xfrm6_extract_header helper
added in an earlier patch, we can now use the one from xfrm_inout.h .
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
so next patch can re-use it from net/xfrm/xfrm_output.c without
causing a linker error when IPV6 is a module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We cannot call this function from the core kernel unless we would force
CONFIG_IPV6=y.
Therefore expose this via ipv6_stubs so we can call it from net/xfrm
in the followup patch.
Since the call is expected to be unlikely, no extra code for the IPV6=y
case is added and we will always eat the indirection cost.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The function only initializes the XFRM CB in the skb.
After previous patch xfrm4_extract_header is only called from
net/xfrm/xfrm_{input,output}.c.
Because of IPV6=m linker errors the ipv6 equivalent
(xfrm6_extract_header) was already placed in xfrm_inout.h because
we can't call functions residing in a module from the core.
So do the same for the ipv4 helper and place it next to the ipv6 one.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In order to keep CONFIG_IPV6=m working, xfrm6_extract_header needs to be
duplicated. It will be removed again in a followup change when the
remaining caller is moved to net/xfrm as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We can use a direct call for ipv4, so move the needed functions
to net/xfrm/xfrm_output.c and call them directly.
For ipv6 the indirection can be avoided as well but it will need
a bit more work -- to ease review it will be done in another patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unnecessary member of address in struct xdp_umem as it is
only used during the umem registration. No need to carry this around
as it is not used during run-time nor when unregistering the umem.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1588599232-24897-3-git-send-email-magnus.karlsson@intel.com
Change two variables names so that it is clearer what they
represent. The first one is xsk_list that in fact only contains the
list of AF_XDP sockets with a Tx component. Change this to xsk_tx_list
for improved clarity. The second variable is size in the ring
structure. One might think that this is the size of the ring, but it
is in fact the size of the umem, copied into the ring structure to
improve performance. Rename this variable umem_size to avoid any
confusion.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1588599232-24897-2-git-send-email-magnus.karlsson@intel.com
After commit b3e80d44f5
("bonding: fix lockdep warning in bond_get_stats()") the dynamic
key is no longer necessary, as we compute nest level at run-time.
So, we can just remove it to save some lockdep key entries.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond0 master bond1
ip link set bond0 nomaster
ip link set bond1 master bond0
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we tell kernel to dump filters from root (ffff:ffff),
those filters on ingress (ffff:0000) are matched, but their
true parents must be dumped as they are. However, kernel
dumps just whatever we tell it, that is either ffff:ffff
or ffff:0000:
$ nl-cls-list --dev=dummy0 --parent=root
cls basic dev dummy0 id none parent root prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent root prio 49152 protocol ip match-all
$ nl-cls-list --dev=dummy0 --parent=ffff:
cls basic dev dummy0 id none parent ffff: prio 49152 protocol ip match-all
cls basic dev dummy0 id :1 parent ffff: prio 49152 protocol ip match-all
This is confusing and misleading, more importantly this is
a regression since 4.15, so the old behavior must be restored.
And, when tc filters are installed on a tc class, the parent
should be the classid, rather than the qdisc handle. Commit
edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
removed the classid we save for filters, we can just restore
this classid in tcf_block.
Steps to reproduce this:
ip li set dev dummy0 up
tc qd add dev dummy0 ingress
tc filter add dev dummy0 parent ffff: protocol arp basic action pass
tc filter show dev dummy0 root
Before this patch:
filter protocol arp pref 49152 basic
filter protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
After this patch:
filter parent ffff: protocol arp pref 49152 basic
filter parent ffff: protocol arp pref 49152 basic handle 0x1
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
Fixes: a10fa20101 ("net: sched: propagate q and parent from caller down to tcf_fill_node")
Fixes: edf6711c98 ("net: sched: remove classid and q fields from tcf_proto")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the gate action to the flow action entry. Add the gate parameters to
the tc_setup_flow_action() queueing to the entries of flow_action_entry
array provide to the driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a ingress frame gate control flow action.
Tc gate action does the work like this:
Assume there is a gate allow specified ingress frames can be passed at
specific time slot, and be dropped at specific time slot. Tc filter
chooses the ingress frames, and tc gate action would specify what slot
does these frames can be passed to device and what time slot would be
dropped.
Tc gate action would provide an entry list to tell how much time gate
keep open and how much time gate keep state close. Gate action also
assign a start time to tell when the entry list start. Then driver would
repeat the gate entry list cyclically.
For the software simulation, gate action requires the user assign a time
clock type.
Below is the setting example in user space. Tc filter a stream source ip
address is 192.168.0.20 and gate action own two time slots. One is last
200ms gate open let frame pass another is last 100ms gate close let
frames dropped. When the ingress frames have reach total frames over
8000000 bytes, the excessive frames will be dropped in that 200000000ns
time slot.
> tc qdisc add dev eth0 ingress
> tc filter add dev eth0 parent ffff: protocol ip \
flower src_ip 192.168.0.20 \
action gate index 2 clockid CLOCK_TAI \
sched-entry open 200000000 -1 8000000 \
sched-entry close 100000000 -1 -1
> tc chain del dev eth0 ingress chain 0
"sched-entry" follow the name taprio style. Gate state is
"open"/"close". Follow with period nanosecond. Then next item is internal
priority value means which ingress queue should put. "-1" means
wildcard. The last value optional specifies the maximum number of
MSDU octets that are permitted to pass the gate during the specified
time interval.
Base-time is not set will be 0 as default, as result start time would
be ((N + 1) * cycletime) which is the minimal of future time.
Below example shows filtering a stream with destination mac address is
10:00:80:00:00:00 and ip type is ICMP, follow the action gate. The gate
action would run with one close time slot which means always keep close.
The time cycle is total 200000000ns. The base-time would calculate by:
1357000000000 + (N + 1) * cycletime
When the total value is the future time, it will be the start time.
The cycletime here would be 200000000ns for this case.
> tc filter add dev eth0 parent ffff: protocol ip \
flower skip_hw ip_proto icmp dst_mac 10:00:80:00:00:00 \
action gate index 12 base-time 1357000000000 \
sched-entry close 200000000 -1 -1 \
clockid CLOCK_TAI
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the behavior of TCP_LINGER2 about its limit. The
sysctl_tcp_fin_timeout used to be the limit of TCP_LINGER2 but now it's
only the default value. A new macro named TCP_FIN_TIMEOUT_MAX is added
as the limit of TCP_LINGER2, which is 2 minutes.
Since TCP_LINGER2 used sysctl_tcp_fin_timeout as the default value
and the limit in the past, the system administrator cannot set the
default value for most of sockets and let some sockets have a greater
timeout. It might be a mistake that let the sysctl to be the limit of
the TCP_LINGER2. Maybe we can add a new sysctl to set the max of
TCP_LINGER2, but FIN-WAIT-2 timeout is usually no need to be too long
and 2 minutes are legal considering TCP specs.
Changes in v3:
- Remove the new socket option and change the TCP_LINGER2 behavior so
that the timeout can be set to value between sysctl_tcp_fin_timeout
and 2 minutes.
Changes in v2:
- Add int overflow check for the new socket option.
Changes in v1:
- Add a new socket option to set timeout greater than
sysctl_tcp_fin_timeout.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik reported a bug with pcpu dst cache when nexthop objects are
used illustrated by the following:
$ ip netns add foo
$ ip -netns foo li set lo up
$ ip -netns foo addr add 2001:db8:11::1/128 dev lo
$ ip netns exec foo sysctl net.ipv6.conf.all.forwarding=1
$ ip li add veth1 type veth peer name veth2
$ ip li set veth1 up
$ ip addr add 2001:db8:10::1/64 dev veth1
$ ip li set dev veth2 netns foo
$ ip -netns foo li set veth2 up
$ ip -netns foo addr add 2001:db8:10::2/64 dev veth2
$ ip -6 nexthop add id 100 via 2001:db8:10::2 dev veth1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Create a pcpu entry on cpu 0:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
Re-add the route entry:
$ ip -6 ro del 2001:db8:11::1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Route get on cpu 0 returns the stale pcpu:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
RTNETLINK answers: Network is unreachable
While cpu 1 works:
$ taskset -a -c 1 ip -6 route get 2001:db8:11::1
2001:db8:11::1 from :: via 2001:db8:10::2 dev veth1 src 2001:db8:10::1 metric 1024 pref medium
Conversion of FIB entries to work with external nexthop objects
missed an important difference between IPv4 and IPv6 - how dst
entries are invalidated when the FIB changes. IPv4 has a per-network
namespace generation id (rt_genid) that is bumped on changes to the FIB.
Checking if a dst_entry is still valid means comparing rt_genid in the
rtable to the current value of rt_genid for the namespace.
IPv6 also has a per network namespace counter, fib6_sernum, but the
count is saved per fib6_node. With the per-node counter only dst_entries
based on fib entries under the node are invalidated when changes are
made to the routes - limiting the scope of invalidations. IPv6 uses a
reference in the rt6_info, 'from', to track the corresponding fib entry
used to create the dst_entry. When validating a dst_entry, the 'from'
is used to backtrack to the fib6_node and check the sernum of it to the
cookie passed to the dst_check operation.
With the inline format (nexthop definition inline with the fib6_info),
dst_entries cached in the fib6_nh have a 1:1 correlation between fib
entries, nexthop data and dst_entries. With external nexthops, IPv6
looks more like IPv4 which means multiple fib entries across disparate
fib6_nodes can all reference the same fib6_nh. That means validation
of dst_entries based on external nexthops needs to use the IPv4 format
- the per-network namespace counter.
Add sernum to rt6_info and set it when creating a pcpu dst entry. Update
rt6_get_cookie to return sernum if it is set and update dst_check for
IPv6 to look for sernum set and based the check on it if so. Finally,
rt6_get_pcpu_route needs to validate the cached entry before returning
a pcpu entry (similar to the rt_cache_valid calls in __mkroute_input and
__mkroute_output for IPv4).
This problem only affects routes using the new, external nexthops.
Thanks to the kbuild test robot for catching the IS_ENABLED needed
around rt_genid_ipv6 before I sent this out.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep all slaves in array so it could be used to get the xmit slave
assume all the slaves are active.
The logic to add slave to the array is like the usable slaves, except
that we also add slaves that currently can't transmit - not up or active.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add two helper functions to get the xmit slave of bond in alb or tlb
mode. Extract the logic of find the xmit slave from the xmit flow
to function. Xmit flow will xmit through this slave and in the
following patches the new .ndo will call to the helper function
to return the xmit slave.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename slave_arr to usable_slaves, since we will have two arrays,
one for the usable slaves and the other to all slaves.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
RFC 6040 recommends propagating an ECT(1) mark from an outer tunnel header
to the inner header if that inner header is already marked as ECT(0). When
RFC 6040 decapsulation was implemented, this case of propagation was not
added. This simply appears to be an oversight, so let's fix that.
Fixes: eccc1bb8d4 ("tunnel: drop packet if ECN present with not-ECT")
Reported-by: Bob Briscoe <ietf@bobbriscoe.net>
Reported-by: Olivier Tilmans <olivier.tilmans@nokia-bell-labs.com>
Cc: Dave Taht <dave.taht@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add, and use in generic netlink, helpers to dump out a netlink
policy to userspace, including all the range validation data,
nested policies etc.
This lets userspace discover what the kernel understands.
For families/commands other than generic netlink, the helpers
need to be used directly in an appropriate command, or we can
add some infrastructure (a new netlink family) that those can
register their policies with for introspection. I'm not that
familiar with non-generic netlink, so that's left out for now.
The data exposed to userspace also includes min and max length
for binary/string data, I've done that instead of letting the
userspace tools figure out whether min/max is intended based
on the type so that we can extend this later in the kernel, we
might want to just use the range data for example.
Because of this, I opted to not directly expose the NLA_*
values, even if some of them are already exposed via BPF, as
with min/max length we don't need to have different types here
for NLA_BINARY/NLA_MIN_LEN/NLA_EXACT_LEN, we just make them
all NL_ATTR_TYPE_BINARY with min/max length optionally set.
Similarly, we don't really need NLA_MSECS, and perhaps can
remove it in the future - but not if we encode it into the
userspace API now. It gets mapped to NL_ATTR_TYPE_U64 here.
Note that the exposing here corresponds to the strict policy
interpretation, and NLA_UNSPEC items are omitted entirely.
To get those, change them to NLA_MIN_LEN which behaves in
exactly the same way, but is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to get the policy's signed/unsigned range
validation data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NLA_MSECS is really equivalent to NLA_U64, allow
it to have range validation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a pointer to a struct indicating the min/max values,
extend the ability to do range validation for arbitrary
values. Small values in the s16 range can be kept in the
policy directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the netlink policy, we currently have a void *validation_data
that's pointing to different things:
* a u32 value for bitfield32,
* the netlink policy for nested/nested array
* the string for NLA_REJECT
Remove the pointer and place appropriate type-safe items in the
union instead.
While at it, completely dissolve the pointer for the bitfield32
case and just put the value there directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl to control hrtimer slack, default of 100 usec.
This gives the opportunity to reduce system overhead,
and help very short RTT flows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MPTCP code uses 2 hooks to process syn-ack
packets, mptcp_rcv_synsent() and the sk_rx_dst_set()
callback.
We can drop the first, moving the relevant code into the
latter, reducing the hooking into the TCP code. This is
also needed by the next patch.
v1 -> v2:
- use local tcp sock ptr instead of casting the sk variable
several times - DaveM
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for nf-next:
1) Add IPS_HW_OFFLOAD status bit, from Bodong Wang.
2) Remove 128-bit limit on the set element data area, rise it
to 64 bytes.
3) Report EOPNOTSUPP for unsupported NAT types and flags.
4) Set up nft_nat flags from the control plane path.
5) Add helper functions to set up the nf_nat_range2 structure.
6) Add netmap support for nft_nat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds the relevant driver and quirk to allow drivers to
report the le_states as being trustworthy.
This has historically been disabled as controllers did not reliably
support this. In particular, this will be used to relax this condition
for controllers that have been well tested and reliable.
/* Most controller will fail if we try to create new connections
* while we have an existing one in slave role.
*/
if (hdev->conn_hash.le_num_slave > 0)
return NULL;
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This extends espintcp to support IPv6, building on the existing code
and the new UDPv6 encapsulation support. Most of the code is either
reused directly (stream parser, ULP) or very similar to the IPv4
variant (net/ipv6/esp6.c changes).
The separation of config options for IPv4 and IPv6 espintcp requires a
bit of Kconfig gymnastics to enable the core code.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds support for encapsulation of ESP over UDPv6. The code
is very similar to the IPv4 encapsulation implementation, and allows
to easily add espintcp on IPv6 as a follow-up.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Extend switchdev API to add support for MRP. The HW is notified in
following cases:
SWITCHDEV_OBJ_ID_MRP: This is used when a MRP instance is added/removed
from the MRP ring.
SWITCHDEV_OBJ_ID_RING_ROLE_MRP: This is used when the role of the node
changes. The current supported roles are MRM and MRC.
SWITCHDEV_OBJ_ID_RING_TEST_MRP: This is used when to start/stop sending
MRP_Test frames on the mrp ring ports. This is called only on nodes that have
the role MRM. In case this fails then the SW will generate the frames.
SWITCHDEV_OBJ_ID_RING_STATE_STATE: This is used when the ring changes it states
to open or closed. This is required to notify HW because the MRP_Test frame
contains the field MRP_InState which contains this information.
SWITCHDEV_ATTR_ID_MRP_PORT_STATE: This is used when the port's state is
changed. It can be in blocking/forwarding mode.
SWITCHDEV_ATTR_ID_MRP_PORT_ROLE: This is used when port's role changes. The
roles of the port can be primary/secondary. This is required to notify HW
because the MRP_Test frame contains the field MRP_PortRole that contains this
information.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In MPTCP, the receive window is shared across all subflows, because it
refers to the mptcp-level sequence space.
MPTCP receivers already place incoming packets on the mptcp socket
receive queue and will charge it to the mptcp socket rcvbuf until
userspace consumes the data.
Update __tcp_select_window to use the occupancy of the parent/mptcp
socket instead of the subflow socket in case the tcp socket is part
of a logical mptcp connection.
This commit doesn't change choice of initial window for passive or active
connections.
While it would be possible to change those as well, this adds complexity
(especially when handling MP_JOIN requests). Furthermore, the MPTCP RFC
specifically says that a MPTCP sender 'MUST NOT use the RCV.WND field
of a TCP segment at the connection level if it does not also carry a DSS
option with a Data ACK field.'
SYN/SYNACK packets do not carry a DSS option with a Data ACK field.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 877d1f6291 ("net: Set sk_txhash from a random number")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX status needs a KHz component, so add freq_offset. We
can reduce the bits for the frequency since 60 GHz isn't
supported.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-5-thomas@adapt-ip.com
[fix commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MHZ_TO_KHZ, and KHZ_TO_MHZ are useful to drivers and
elsewhere so export these in the common ieee80211 header.
Move the power helpers also because we might as well.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-2-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver tells mac80211 to sends ADDBA with SSN (starting sequence number)
from the head of the queue, while the transmission of all the frames in the
queue may take a while, which causes the peer to time out. In order to
fix this scenario, add an option to defer ADDBA transmit until queue
is drained.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.0f27423fec75.If67daab123a27c1cbddef000d6a3f212aa6309ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert a user space registration for processing multicast Action frames
(NL80211_CMD_REGISTER_FRAME with NL80211_ATTR_RECEIVE_MULTICAST) to a
new enum ieee80211_filter_flags bit FIF_MCAST_ACTION so that drivers can
update their RX filter parameters appropriately, if needed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200421144815.19175-1-jouni@codeaurora.org
[rename variables to rx_mcast_action_reg indicating action frames only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For DPP, there's a need to receive multicast action frames,
but many drivers need a special filter configuration for this.
Support announcing from userspace in the management registration
that multicast RX is required, with an extended feature flag if
the driver handles this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124013.c46238801048.Ib041d437ce0bff28a0c6d5dc915f68f1d8591002@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend cfg80211_rx_unprot_mlme_mgmt() to cover indication of unprotected
Beacon frames in addition to the previously used Deauthentication and
Disassociation frames. The Beacon frame case is quite similar, but has
couple of exceptions: this is used both with fully unprotected and also
incorrectly protected frames and there is a rate limit on the events to
avoid unnecessary flooding netlink events in case something goes wrong.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-1-jouni@codeaurora.org
[add missing kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the DEV_MAP_BULK_SIZE macro to the header file so that drivers
can directly use it as the maximum number of xdp_frames received in the
.ndo_xdp_xmit() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See:
https://www.rfc-editor.org/authors/rfc8781.txt
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: c24a77edc9 ("ipv6: ndisc: add support for 'PREF64' dns64 prefix identifier")
Signed-off-by: David S. Miller <davem@davemloft.net>
When ESP encapsulation is enabled on a TCP socket, I'm replacing the
existing ->sk_destruct callback with espintcp_destruct. We still need to
call the old callback to perform the other cleanups when the socket is
destroyed. Save the old callback, and call it from espintcp_destruct.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
TCP stack is dumb in how it cooks its output packets.
Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.
If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-04-17
Here's the first bluetooth-next pull request for the 5.8 kernel:
- Added debugfs option to control MITM flag usage during pairing
- Added new BT_MODE socket option
- Added support for Qualcom QCA6390 device
- Added support for Realtek RTL8761B device
- Added support for mSBC audio codec over USB endpoints
- Added framework for Microsoft HCI vendor extensions
- Added new Read Security Information management command
- Fixes/cleanup to link layer privacy related code
- Various other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the controller is being reset or power cycled, then the flag
HCI_LL_RPA_RESOLUTION which indicates if controller based address
resolution is active needs to be also reset.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The list of LE features constants has gotten a bit confused. It lost the
order and gained duplicated. Clean this up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The behaviour for what is considered an anycast address changed in
commit 45e4fd2668 ("ipv6: Only create RTF_CACHE routes after
encountering pmtu exception"). This now considers the first
address in a subnet where there is a route via a gateway
to be an anycast address.
This breaks path MTU discovery and traceroutes when a host in a
remote network uses the address at the start of a prefix
(eg 2600:: advertised as 2600::/48 in the DFZ) as ICMP errors
will not be sent to anycast addresses.
This patch excludes any routes with a gateway, or via point to
point links, like the behaviour previously from
rt6_is_gw_or_nonexthop in net/ipv6/route.c.
This can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8:100:: dev lo nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip route add 2001:db8:100::/64 via 2001:db8::1
ip netns exec test sysctl net.ipv6.conf.all.forwarding=1
ip route add 2001:db8:1::1 via 2001:db8::2
ping -I 2001:db8::1 2001:db8:1::1 -c1
ping -I 2001:db8:100:: 2001:db8:1::1 -c1
ip addr delete 2001:db8:100:: dev lo
ip netns delete test
Currently the first ping will get back a destination unreachable ICMP
error, but the second will never get a response, with "icmp6_send:
acast source" logged. After this patch, both get destination
unreachable ICMP replies.
Fixes: 45e4fd2668 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Signed-off-by: Tim Stallard <code@timstallard.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warnings related to kernel-doc notation, and wording in
function description.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net, they are:
1) Fix spurious overlap condition in the rbtree tree, from Stefano Brivio.
2) Fix possible uninitialized pointer dereference in nft_lookup.
3) IDLETIMER v1 target matches the Android layout, from
Maciej Zenczykowski.
4) Dangling pointer in nf_tables_set_alloc_name, from Eric Dumazet.
5) Fix RCU warning splat in ipset find_set_type(), from Amol Grover.
6) Report EOPNOTSUPP on unsupported set flags and object types in sets.
7) Add NFT_SET_CONCAT flag to provide consistent error reporting
when users defines set with ranges in concatenations in old kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- Fix read with O_NONBLOCK to allow incomplete read and return immediately
- Rest is just cleanup (indent, unused field in struct, extra semicolon)
-----BEGIN PGP SIGNATURE-----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=wAe5
-----END PGP SIGNATURE-----
Merge tag '9p-for-5.7' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Not much new, but a few patches for this cycle:
- Fix read with O_NONBLOCK to allow incomplete read and return
immediately
- Rest is just cleanup (indent, unused field in struct, extra
semicolon)"
* tag '9p-for-5.7' of git://github.com/martinetd/linux:
net/9p: remove unused p9_req_t aux field
9p: read only once on O_NONBLOCK
9pnet: allow making incomplete read requests
9p: Remove unneeded semicolon
9p: Fix Kconfig indentation
Initialize set lookup matching element to NULL. Otherwise, the
NFT_LOOKUP_F_INV flag reverses the matching logic and it leads to
deference an uninitialized pointer to the matching element. Make sure
element data area and stateful expression are accessed if there is a
matching set element.
This patch undoes 24791b9aa1 ("netfilter: nft_set_bitmap: initialize set
element extension in lookups") which is not required anymore.
Fixes: 339706bc21 ("netfilter: nft_lookup: update element stateful expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch assigns the next free HCI device identifier to Bluetooth
devices based on VIRTIO devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
[Build system]
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define
a fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
[Kconfig]
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig files
- relax the 'imply' behavior so that symbols implied by y can become m
- make 'imply' obey 'depends on' in order to make 'imply' really weak
[Misc]
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups
-----BEGIN PGP SIGNATURE-----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=wT8A
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
"Build system:
- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)
- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable
- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files
- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'
- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add support to specify a stateful expression in set definitions,
this allows users to specify e.g. counters per set elements.
2) Flowtable software counter support.
3) Flowtable hardware offload counter support, from wenxu.
3) Parallelize flowtable hardware offload requests, from Paul Blakey.
This includes a patch to add one work entry per offload command.
4) Several patches to rework nf_queue refcount handling, from Florian
Westphal.
4) A few fixes for the flowtable tunnel offload: Fix crash if tunneling
information is missing and set up indirect flow block as TC_SETUP_FT,
patch from wenxu.
5) Stricter netlink attribute sanity check on filters, from Romain Bellan
and Florent Fourcot.
5) Annotations to make sparse happy, from Jules Irenge.
6) Improve icmp errors in debugging information, from Haishuang Yan.
7) Fix warning in IPVS icmp error debugging, from Haishuang Yan.
8) Fix endianess issue in tcp extension header, from Sergey Marinkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch allowed device drivers to publish their default
binding between packet trap policers and packet trap groups. However,
some users might not be content with this binding and would like to
change it.
In case user space passed a packet trap policer identifier when setting
a packet trap group, invoke the appropriate device driver callback and
pass the new policer identifier.
v2:
* Check for presence of 'DEVLINK_ATTR_TRAP_POLICER_ID' in
devlink_trap_group_set() and bail if not present
* Add extack error message in case trap group was partially modified
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are used to aggregate logically related packet traps.
Currently, these groups allow user space to batch operations such as
setting the trap action of all member traps.
In order to prevent the CPU from being overwhelmed by too many trapped
packets, it is desirable to bind a packet trap policer to these groups.
For example, to limit all the packets that encountered an exception
during routing to 10Kpps.
Allow device drivers to bind default packet trap policers to packet trap
groups when the latter are registered with devlink.
The next patch will enable user space to change this default binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices capable of offloading the kernel's datapath and perform
functions such as bridging and routing must also be able to send (trap)
specific packets to the kernel (i.e., the CPU) for processing.
For example, a device acting as a multicast-aware bridge must be able to
trap IGMP membership reports to the kernel for processing by the bridge
module.
In most cases, the underlying device is capable of handling packet rates
that are several orders of magnitude higher compared to those that can
be handled by the CPU.
Therefore, in order to prevent the underlying device from overwhelming
the CPU, devices usually include packet trap policers that are able to
police the trapped packets to rates that can be handled by the CPU.
This patch allows capable device drivers to register their supported
packet trap policers with devlink. User space can then tune the
parameters of these policer (currently, rate and burst size) and read
from the device the number of packets that were dropped by the policer,
if supported.
Subsequent patches in the series will allow device drivers to create
default binding between these policers and packet trap groups and allow
user space to change the binding.
v2:
* Add 'strict_start_type' in devlink policy
* Have device drivers provide max/min rate/burst size for each policer.
Use them to check validity of user provided parameters
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid taking a reference on listen sockets by checking the socket type
in the sk_assign and in the corresponding skb_steal_sock() code in the
the transport layer, and by ensuring that the prefetch free (sock_pfree)
function uses the same logic to check whether the socket is refcounted.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200329225342.16317-4-joe@wand.net.nz
Refactor the UDP/TCP handlers slightly to allow skb_steal_sock() to make
the determination of whether the socket is reference counted in the case
where it is prefetched by earlier logic such as early_demux.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200329225342.16317-3-joe@wand.net.nz
Add support for TPROXY via a new bpf helper, bpf_sk_assign().
This helper requires the BPF program to discover the socket via a call
to bpf_sk*_lookup_*(), then pass this socket to the new helper. The
helper takes its own reference to the socket in addition to any existing
reference that may or may not currently be obtained for the duration of
BPF processing. For the destination socket to receive the traffic, the
traffic must be routed towards that socket via local route. The
simplest example route is below, but in practice you may want to route
traffic more narrowly (eg by CIDR):
$ ip route add local default dev lo
This patch avoids trying to introduce an extra bit into the skb->sk, as
that would require more invasive changes to all code interacting with
the socket to ensure that the bit is handled correctly, such as all
error-handling cases along the path from the helper in BPF through to
the orphan path in the input. Instead, we opt to use the destructor
variable to switch on the prefetch of the socket.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200329225342.16317-2-joe@wand.net.nz
-----BEGIN PGP SIGNATURE-----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=bYLJ
-----END PGP SIGNATURE-----
Merge tag 'for-5.7/io_uring-2020-03-29' of git://git.kernel.dk/linux-block
Pull io_uring updates from Jens Axboe:
"Here are the io_uring changes for this merge window. Light on new
features this time around (just splice + buffer selection), lots of
cleanups, fixes, and improvements to existing support. In particular,
this contains:
- Cleanup fixed file update handling for stack fallback (Hillf)
- Re-work of how pollable async IO is handled, we no longer require
thread offload to handle that. Instead we rely using poll to drive
this, with task_work execution.
- In conjunction with the above, allow expendable buffer selection,
so that poll+recv (for example) no longer has to be a split
operation.
- Make sure we honor RLIMIT_FSIZE for buffered writes
- Add support for splice (Pavel)
- Linked work inheritance fixes and optimizations (Pavel)
- Async work fixes and cleanups (Pavel)
- Improve io-wq locking (Pavel)
- Hashed link write improvements (Pavel)
- SETUP_IOPOLL|SETUP_SQPOLL improvements (Xiaoguang)"
* tag 'for-5.7/io_uring-2020-03-29' of git://git.kernel.dk/linux-block: (54 commits)
io_uring: cleanup io_alloc_async_ctx()
io_uring: fix missing 'return' in comment
io-wq: handle hashed writes in chains
io-uring: drop 'free_pfile' in struct io_file_put
io-uring: drop completion when removing file
io_uring: Fix ->data corruption on re-enqueue
io-wq: close cancel gap for hashed linked work
io_uring: make spdxcheck.py happy
io_uring: honor original task RLIMIT_FSIZE
io-wq: hash dependent work
io-wq: split hashing and enqueueing
io-wq: don't resched if there is no work
io-wq: remove duplicated cancel code
io_uring: fix truncated async read/readv and write/writev retry
io_uring: dual license io_uring.h uapi header
io_uring: io_uring_enter(2) don't poll while SETUP_IOPOLL|SETUP_SQPOLL enabled
io_uring: Fix unused function warnings
io_uring: add end-of-bits marker and build time verify it
io_uring: provide means of removing buffers
io_uring: add IOSQE_BUFFER_SELECT support for IORING_OP_RECVMSG
...
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-03-29
Here are a few more Bluetooth patches for the 5.7 kernel:
- Fix assumption of encryption key size when reading fails
- Add support for DEFER_SETUP with L2CAP Enhanced Credit Based Mode
- Fix issue with auto-connected devices
- Fix suspend handling when entering the state fails
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach taken to pass the port policer methods on to drivers is
pragmatic. It is similar to the port mirroring implementation (in that
the DSA core does all of the filter block interaction and only passes
simple operations for the driver to implement) and dissimilar to how
flow-based policers are going to be implemented (where the driver has
full control over the flow_cls_offload data structure).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.
$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 10 sec used 10 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats immediate <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to pass value and selector to. The helper packs them
into struct and puts them into netlink message.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-03-28
1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
in xfrm_state_alloc(). From Huang Zijiang.
2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
so share this function to avoide code duplcation.
From Raed Salem.
3) Add offload support for esp beet mode.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exported via same /proc file as the Linux TCP MIB counters, so "netstat -s"
or "nstat" will show them automatically.
The MPTCP MIB counters are allocated in a distinct pcpu area in order to
avoid bloating/wasting TCP pcpu memory.
Counters are allocated once the first MPTCP socket is created in a
network namespace and free'd on exit.
If no sockets have been allocated, all-zero mptcp counters are shown.
The MIB counter list is taken from the multipath-tcp.org kernel, but
only a few counters have been picked up so far. The counter list can
be increased at any time later on.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subflow creation may be initiated by the path manager when
the primary connection is fully established and a remote
address has been received via ADD_ADDR.
Create an in-kernel sock and use kernel_connect() to
initiate connection.
Passive sockets can't acquire the mptcp socket lock at
subflow creation time, so an additional list protected by
a new spinlock is used to track the MPJ subflows.
Such list is spliced into conn_list tail every time the msk
socket lock is acquired, so that it will not interfere
with data flow on the original connection.
Data flow and connection failover not addressed by this commit.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process the MP_JOIN option in a SYN packet with the same flow
as MP_CAPABLE but when the third ACK is received add the
subflow to the MPTCP socket subflow list instead of adding it to
the TCP socket accept queue.
The subflow is added at the end of the subflow list so it will not
interfere with the existing subflows operation and no data is
expected to be transmitted on it.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling for sending and receiving the ADD_ADDR, ADD_ADDR6,
and RM_ADDR suboptions.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_ct_acct_add function to update the conntrack counter
with packets and bytes.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix a redefinition of 'net_gen_cookie' error that was overlooked
when net ns is not configured.
Fixes: f318903c0b ("bpf: Add netns cookie and enable it for bpf cgroup hooks")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The refcount is done via entry->skb, which does work fine.
Major problem: When putting the refcount of the bridge ports, we
must always put the references while the skb is still around.
However, we will need to put the references after okfn() to avoid
a possible 1 -> 0 -> 1 refcount transition, so we cannot use the
skb pointer anymore.
Place the physports in the queue entry structure instead to allow
for refcounting changes in the next patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a preparation patch, no logical changes.
Move free_entry into core and rename it to something more sensible.
Will ease followup patches which will complicate the refcount handling.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Today, Kubernetes is still operating on cgroups v1, however, it is
possible to retrieve the task's classid based on 'current' out of
connect(), sendmsg(), recvmsg() and bind-related hooks for orchestrators
which attach to the root cgroup v2 hook in a mixed env like in case
of Cilium, for example, in order to then correlate certain pod traffic
and use it as part of the key for BPF map lookups.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/555e1c69db7376c0947007b4951c260e1074efc3.1585323121.git.daniel@iogearbox.net
In Cilium we're mainly using BPF cgroup hooks today in order to implement
kube-proxy free Kubernetes service translation for ClusterIP, NodePort (*),
ExternalIP, and LoadBalancer as well as HostPort mapping [0] for all traffic
between Cilium managed nodes. While this works in its current shape and avoids
packet-level NAT for inter Cilium managed node traffic, there is one major
limitation we're facing today, that is, lack of netns awareness.
In Kubernetes, the concept of Pods (which hold one or multiple containers)
has been built around network namespaces, so while we can use the global scope
of attaching to root BPF cgroup hooks also to our advantage (e.g. for exposing
NodePort ports on loopback addresses), we also have the need to differentiate
between initial network namespaces and non-initial one. For example, ExternalIP
services mandate that non-local service IPs are not to be translated from the
host (initial) network namespace as one example. Right now, we have an ugly
work-around in place where non-local service IPs for ExternalIP services are
not xlated from connect() and friends BPF hooks but instead via less efficient
packet-level NAT on the veth tc ingress hook for Pod traffic.
On top of determining whether we're in initial or non-initial network namespace
we also have a need for a socket-cookie like mechanism for network namespaces
scope. Socket cookies have the nice property that they can be combined as part
of the key structure e.g. for BPF LRU maps without having to worry that the
cookie could be recycled. We are planning to use this for our sessionAffinity
implementation for services. Therefore, add a new bpf_get_netns_cookie() helper
which would resolve both use cases at once: bpf_get_netns_cookie(NULL) would
provide the cookie for the initial network namespace while passing the context
instead of NULL would provide the cookie from the application's network namespace.
We're using a hole, so no size increase; the assignment happens only once.
Therefore this allows for a comparison on initial namespace as well as regular
cookie usage as we have today with socket cookies. We could later on enable
this helper for other program types as well as we would see need.
(*) Both externalTrafficPolicy={Local|Cluster} types
[0] https://github.com/cilium/cilium/blob/master/bpf/bpf_sock.c
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/c47d2346982693a9cf9da0e12690453aded4c788.1585323121.git.daniel@iogearbox.net
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently flow offload threads are synchronized by the flow block mutex.
Use rw lock instead to increase flow insertion (read) concurrency.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The indirect block setup should use TC_SETUP_FT as the type instead of
TC_SETUP_BLOCK. Adjust existing users of the indirect flow block
infrastructure.
Fixes: b5140a36da ("netfilter: flowtable: add indr block setup support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A user doesn't necessarily want to wait for all the requested data to
be available, since the waiting time for each request is unbounded.
The new method permits sending one read request at a time and getting
the response ASAP, allowing to use 9pnet with synthetic file systems
representing arbitrary data streams.
Link: http://lkml.kernel.org/r/20200205204053.12751-1-l29ah@cock.li
Signed-off-by: Sergey Alirzaev <l29ah@cock.li>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
When HW offloading is enabled, offloaded stats should be used, because
s/w stats are wrong and out of sync with the HW in this case.
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to reference a net_device from a MACsec context. This
is needed to allow implementing MACsec operations in net device drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is trivial since we already have support for the entirely
identical (from the kernel's point of view) RDNSS, DNSSL, etc. that
also contain opaque data that needs to be passed down to userspace
for further processing.
As specified in draft-ietf-6man-ra-pref64-09 (while it is still a draft,
it is purely waiting on the RFC Editor for cleanups and publishing):
PREF64 option contains lifetime and a (up to) 96-bit IPv6 prefix.
The 8-bit identifier of the option type as assigned by the IANA is 38.
Since we lack DNS64/NAT64/CLAT support in kernel at the moment,
thus this option should also be passed on to userland.
See:
https://tools.ietf.org/html/draft-ietf-6man-ra-pref64-09https://www.iana.org/assignments/icmpv6-parameters/icmpv6-parameters.xhtml#icmpv6-parameters-5
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an error message when device wasn't found.
While there, also set the bad attribute's offset in extack.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the DEVLINK_CMD_REGION_NEW command for creating
snapshots. This new command parallels the existing
DEVLINK_CMD_REGION_DEL.
In order for DEVLINK_CMD_REGION_NEW to work for a region, the new
".snapshot" operation must be implemented in the region's ops structure.
The desired snapshot id must be provided. This helps avoid confusion on
the purpose of DEVLINK_CMD_REGION_NEW, and keeps the API simpler.
The requested id will be inserted into the xarray tracking the number of
snapshots using each id. If this id is already used by another snapshot
on any region, an error will be returned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each snapshot created for a devlink region must have an id. These ids
are supposed to be unique per "event" that caused the snapshot to be
created. Drivers call devlink_region_snapshot_id_get to obtain a new id
to use for a new event trigger. The id values are tracked per devlink,
so that the same id number can be used if a triggering event creates
multiple snapshots on different regions.
There is no mechanism for snapshot ids to ever be reused. Introduce an
xarray to store the count of how many snapshots are using a given id,
replacing the snapshot_id field previously used for picking the next id.
The devlink_region_snapshot_id_get() function will use xa_alloc to
insert an initial value of 1 value at an available slot between 0 and
U32_MAX.
The new __devlink_snapshot_id_increment() and
__devlink_snapshot_id_decrement() functions will be used to track how
many snapshots currently use an id.
Drivers must now call devlink_snapshot_id_put() in order to release
their reference of the snapshot id after adding region snapshots.
By tracking the total number of snapshots using a given id, it is
possible for the decrement() function to erase the id from the xarray
when it is not in use.
With this method, a snapshot id can become reused again once all
snapshots that referred to it have been deleted via
DEVLINK_CMD_REGION_DEL, and the driver has finished adding snapshots.
This work also paves the way to introduce a mechanism for userspace to
request a snapshot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink_snapshot_id_get() function returns a snapshot id. The
snapshot id is a u32, so there is no way to indicate an error code.
A future change is going to possibly add additional cases where this
function could fail. Refactor the function to return the snapshot id in
an argument, so that it can return zero or an error value.
This ensures that snapshot ids cannot be confused with error values, and
aids in the future refactor of snapshot id allocation management.
Because there is no current way to release previously used snapshot ids,
add a simple check ensuring that an error is reported in case the
snapshot_id would over flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not makes sense that two snapshots for a given region would use
different destructors. Simplify snapshot creation by adding
a .destructor op for regions.
This operation will replace the data_destructor for the snapshot
creation, and makes snapshot creation easier.
Noticed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the devlink region code in preparation for adding new operations
on regions.
Create a devlink_region_ops structure, and move the name pointer from
within the devlink_region structure into the ops structure (similar to
the devlink_health_reporter_ops).
This prepares the regions to enable support of additional operations in
the future such as requesting snapshots, or accessing the region
directly without a snapshot.
In order to re-use the constant strings in the mlx4 driver their
declaration must be changed to 'const char * const' to ensure the
compiler realizes that both the data and the pointer cannot change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This field references FLOW_ACTION_PACKET_EDIT. Such action does not exist
though. Instead the field is used for FLOW_ACTION_MANGLE and _ADD.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1af ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress")
Reported-by: noreply@ellerman.id.au
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-21
Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.
This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.
Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53eca1f347 ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfp driver uses ``fw.bundle_id`` to represent a unique identifier of the
entire firmware bundle.
A future change is going to introduce a similar notion in the ice
driver, so promote ``fw.bundle_id`` into a generic version now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* HE ranging (fine timing measurement) API support
* hwsim gets virtio support, for use with wmediumd,
to be able to simulate with multiple machines
* eapol-over-nl80211 improvements to exclude preauth
* IBSS reset support, to recover connections from
userspace
* and various others.
-----BEGIN PGP SIGNATURE-----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=t3QF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-03-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes:
* HE ranging (fine timing measurement) API support
* hwsim gets virtio support, for use with wmediumd,
to be able to simulate with multiple machines
* eapol-over-nl80211 improvements to exclude preauth
* IBSS reset support, to recover connections from
userspace
* and various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit f747632b60 ("bpf: sockmap: Move generic sockmap
hooks from BPF TCP"), tcp_bpf_recvmsg() is not used out of
tcp_bpf.c, so make it static and remove it from tcp.h. Also move
it to BPF_STREAM_PARSER #ifdef to fix unused function warnings.
Fixes: f747632b60 ("bpf: sockmap: Move generic sockmap hooks from BPF TCP")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200320023426.60684-3-yuehaibing@huawei.com
Drivers that trigger roaming need to know the lifetime of the configured
PMKSA for deciding whether to trigger the full or PMKSA cache based
authentication. The configured PMKSA is invalid after the PMK lifetime
has expired and must not be used after that and the STA needs to
disassociate if the PMK expires. Hence the STA is expected to refresh
the PMK with a full authentication before this happens (e.g., when
reassociating to a new BSS the next time or by performing EAPOL
reauthentication depending on the AKM) to avoid unnecessary
disconnection.
The PMK reauthentication threshold is the percentage of the PMK lifetime
value and indicates to the driver to trigger a full authentication roam
(without PMKSA caching) after the reauthentication threshold time, but
before the PMK timer has expired. Authentication methods like SAE need
to be able to generate a new PMKSA entry without having to force a
disconnection after this threshold timeout. If no roaming occurs between
the reauthentication threshold time and PMK lifetime expiration,
disassociation is still forced.
The new attributes for providing these values correspond to the dot11
MIB variables dot11RSNAConfigPMKLifetime and
dot11RSNAConfigPMKReauthThreshold.
This type of functionality is already available in cases where user
space component is in control of roaming. This commit extends that same
capability into cases where parts or all of this functionality is
offloaded to the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200312235903.18462-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the AP's HE operation element to the driver.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-18-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for requesting that the ranging measurement will use
the trigger-based / non trigger-based flow instead of the EDCA based
flow.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-03-19
Here's the main bluetooth-next pull request for the 5.7 kernel.
- Added wideband speech support to mgmt and the ability for HCI drivers
to declare support for it.
- Added initial support for L2CAP Enhanced Credit Based Mode
- Fixed suspend handling for several use cases
- Fixed Extended Advertising related issues
- Added support for Realtek 8822CE device
- Added DT bindings for QTI chip WCN3991
- Cleanups to replace zero-length arrays with flexible-array members
- Several other smaller cleanups & fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The skbedit action "priority" is used for adjusting SKB priority. Allow
drivers to offload the action by introducing two new skbedit getters and a
new flow action, and initializing appropriately in tc_setup_flow_action().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two functions is_tcf_skbedit_mark() and is_tcf_skbedit_ptype() have a
very similar structure. A follow-up patch will add one more such function.
Instead of more cut'n'pasting, extract a helper function that checks
whether a TC action is an skbedit with the required flag. Convert the two
existing functions into thin wrappers around the helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to specify the stateful expression for the
elements in this set via NFTA_SET_EXPR. This new feature allows you to
turn on counters for all of the elements in this set.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Use nf_flow_offload_tuple() to fetch flow stats, from Paul Blakey.
2) Add new xt_IDLETIMER hard mode, from Manoj Basapathi.
Follow up patch to clean up this new mode, from Dan Carpenter.
3) Add support for geneve tunnel options, from Xin Long.
4) Make sets built-in and remove modular infrastructure for sets,
from Florian Westphal.
5) Remove unused TEMPLATE_NULLS_VAL, from Li RongQing.
6) Statify nft_pipapo_get, from Chen Wandun.
7) Use C99 flexible-array member, from Gustavo A. R. Silva.
8) More descriptive variable names for bitwise, from Jeremy Sowden.
9) Four patches to add tunnel device hardware offload to the flowtable
infrastructure, from wenxu.
10) pipapo set supports for 8-bit grouping, from Stefano Brivio.
11) pipapo can switch between nibble and byte grouping, also from
Stefano.
12) Add AVX2 vectorized version of pipapo, from Stefano Brivio.
13) Update pipapo to be use it for single ranges, from Stefano.
14) Add stateful expression support to elements via control plane,
eg. counter per element.
15) Re-visit sysctls in unprivileged namespaces, from Florian Westphal.
15) Add new egress hook, from Lukas Wunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some packet schedulers might want to add a slack
when programming hrtimers. This can reduce number
of interrupts and increase batch sizes and thus
give good xmit_more savings.
This commit adds qdisc_watchdog_schedule_range_ns()
helper, with an extra delta_ns parameter.
Legacy qdisc_watchdog_schedule_n() becomes an inline
passing a zero slack.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink support of extended packet number cipher suites,
allows adding and updating XPN macsec interfaces.
Added support in:
* Creating interfaces with GCM-AES-XPN-128 and GCM-AES-XPN-256 suites.
* Setting and getting 64bit packet numbers with of SAs.
* Setting (only on SA creation) and getting ssci of SAs.
* Setting salt when installing a SAK.
Added 2 cipher suite identifiers according to 802.1AE-2018 table 14-1:
* MACSEC_CIPHER_ID_GCM_AES_XPN_128
* MACSEC_CIPHER_ID_GCM_AES_XPN_256
In addition, added 2 new netlink attribute types:
* MACSEC_SA_ATTR_SSCI
* MACSEC_SA_ATTR_SALT
Depends on: macsec: Support XPN frame handling - IEEE 802.1AEbw.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support extended packet number cipher suites (802.1AEbw) frames handling.
This does not include the needed netlink patches.
* Added xpn boolean field to `struct macsec_secy`.
* Added ssci field to `struct_macsec_tx_sa` (802.1AE figure 10-5).
* Added ssci field to `struct_macsec_rx_sa` (802.1AE figure 10-5).
* Added salt field to `struct macsec_key` (802.1AE 10.7 NOTE 1).
* Created pn_t type for easy access to lower and upper halves.
* Created salt_t type for easy access to the "ssci" and "pn" parts.
* Created `macsec_fill_iv_xpn` function to create IV in XPN mode.
* Support in PN recovery and preliminary replay check in XPN mode.
In addition, according to IEEE 802.1AEbw figure 10-5, the PN of incoming
frame can be 0 when XPN cipher suite is used, so fixed the function
`macsec_validate_skb` to fail on PN=0 only if XPN is off.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the AVX2 set is available, we can exploit the repetitive
characteristic of this algorithm to provide a fast, vectorised
version by using 256-bit wide AVX2 operations for bucket loads and
bitwise intersections.
In most cases, this implementation consistently outperforms rbtree
set instances despite the fact they are configured to use a given,
single, ranged data type out of the ones used for performance
measurements by the nft_concat_range.sh kselftest.
That script, injecting packets directly on the ingoing device path
with pktgen, reports, averaged over five runs on a single AMD Epyc
7402 thread (3.35GHz, 768 KiB L1D$, 12 MiB L2$), the figures below.
CONFIG_RETPOLINE was not set here.
Note that this is not a fair comparison over hash and rbtree set
types: non-ranged entries (used to have a reference for hash types)
would be matched faster than this, and matching on a single field
only (which is the case for rbtree) is also significantly faster.
However, it's not possible at the moment to choose this set type
for non-ranged entries, and the current implementation also needs
a few minor adjustments in order to match on less than two fields.
---------------.-----------------------------------.------------.
AMD Epyc 7402 | baselines, Mpps | this patch |
1 thread |___________________________________|____________|
3.35GHz | | | | | |
768KiB L1D$ | netdev | hash | rbtree | | |
---------------| hook | no | single | | pipapo |
type entries | drop | ranges | field | pipapo | AVX2 |
---------------|--------|--------|--------|--------|------------|
net,port | | | | | |
1000 | 19.0 | 10.4 | 3.8 | 4.0 | 7.5 +87% |
---------------|--------|--------|--------|--------|------------|
port,net | | | | | |
100 | 18.8 | 10.3 | 5.8 | 6.3 | 8.1 +29% |
---------------|--------|--------|--------|--------|------------|
net6,port | | | | | |
1000 | 16.4 | 7.6 | 1.8 | 2.1 | 4.8 +128% |
---------------|--------|--------|--------|--------|------------|
port,proto | | | | | |
30000 | 19.6 | 11.6 | 3.9 | 0.5 | 2.6 +420% |
---------------|--------|--------|--------|--------|------------|
net6,port,mac | | | | | |
10 | 16.5 | 5.4 | 4.3 | 3.4 | 4.7 +38% |
---------------|--------|--------|--------|--------|------------|
net6,port,mac, | | | | | |
proto 1000 | 16.5 | 5.7 | 1.9 | 1.4 | 3.6 +26% |
---------------|--------|--------|--------|--------|------------|
net,mac | | | | | |
1000 | 19.0 | 8.4 | 3.9 | 2.5 | 6.4 +156% |
---------------'--------'--------'--------'--------'------------'
A similar strategy could be easily reused to implement specialised
versions for other SIMD sets, and I plan to post at least a NEON
version at a later time.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch support both ipv4 and ipv6 tunnel_id, tunnel_src and
tunnel_dst match for flowtable offload
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Lastly, fix checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
in net/bridge/netfilter/ebtables.c
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
They do not need to be writeable anymore.
v2: remove left-over __read_mostly annotation in set_pipapo.c (Stefano)
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Placing nftables set support in an extra module is pointless:
1. nf_tables needs dynamic registeration interface for sake of one module
2. nft heavily relies on sets, e.g. even simple rule like
"nft ... tcp dport { 80, 443 }" will not work with _SETS=n.
IOW, either nftables isn't used or both nf_tables and nf_tables_set
modules are needed anyway.
With extra module:
307K net/netfilter/nf_tables.ko
79K net/netfilter/nf_tables_set.ko
text data bss dec filename
146416 3072 545 150033 nf_tables.ko
35496 1817 0 37313 nf_tables_set.ko
This patch:
373K net/netfilter/nf_tables.ko
178563 4049 545 183157 nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When the RED Qdisc is currently configured to enable ECN, the RED algorithm
is used to decide whether a certain SKB should be marked. If that SKB is
not ECN-capable, it is early-dropped.
It is also possible to keep all traffic in the queue, and just mark the
ECN-capable subset of it, as appropriate under the RED algorithm. Some
switches support this mode, and some installations make use of it.
To that end, add a new RED flag, TC_RED_NODROP. When the Qdisc is
configured with this flag, non-ECT traffic is enqueued instead of being
early-dropped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qdiscs RED, GRED, SFQ and CHOKE use different subsets of the same pool
of global RED flags. These are passed in tc_red_qopt.flags. However none of
these qdiscs validate the flag field, and just copy it over wholesale to
internal structures, and later dump it back. (An exception is GRED, which
does validate for VQs -- however not for the main setup.)
A broken userspace can therefore configure a qdisc with arbitrary
unsupported flags, and later expect to see the flags on qdisc dump. The
current ABI therefore allows storage of several bits of custom data to
qdisc instances of the types mentioned above. How many bits, depends on
which flags are meaningful for the qdisc in question. E.g. SFQ recognizes
flags ECN and HARDDROP, and the rest is not interpreted.
If SFQ ever needs to support ADAPTATIVE, it needs another way of doing it,
and at the same time it needs to retain the possibility to store 6 bits of
uninterpreted data. Likewise RED, which adds a new flag later in this
patchset.
To that end, this patch adds a new function, red_get_flags(), to split the
passed flags of RED-like qdiscs to flags and user bits, and
red_validate_flags() to validate the resulting configuration. It further
adds a new attribute, TCA_RED_FLAGS, to pass arbitrary flags.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-03-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 86 non-merge commits during the last 12 day(s) which contain
a total of 107 files changed, 5771 insertions(+), 1700 deletions(-).
The main changes are:
1) Add modify_return attach type which allows to attach to a function via
BPF trampoline and is run after the fentry and before the fexit programs
and can pass a return code to the original caller, from KP Singh.
2) Generalize BPF's kallsyms handling and add BPF trampoline and dispatcher
objects to be visible in /proc/kallsyms so they can be annotated in
stack traces, from Jiri Olsa.
3) Extend BPF sockmap to allow for UDP next to existing TCP support in order
in order to enable this for BPF based socket dispatch, from Lorenz Bauer.
4) Introduce a new bpftool 'prog profile' command which attaches to existing
BPF programs via fentry and fexit hooks and reads out hardware counters
during that period, from Song Liu. Example usage:
bpftool prog profile id 337 duration 3 cycles instructions llc_misses
4228 run_cnt
3403698 cycles (84.08%)
3525294 instructions # 1.04 insn per cycle (84.05%)
13 llc_misses # 3.69 LLC misses per million isns (83.50%)
5) Batch of improvements to libbpf, bpftool and BPF selftests. Also addition
of a new bpf_link abstraction to keep in particular BPF tracing programs
attached even when the applicaion owning them exits, from Andrii Nakryiko.
6) New bpf_get_current_pid_tgid() helper for tracing to perform PID filtering
and which returns the PID as seen by the init namespace, from Carlos Neira.
7) Refactor of RISC-V JIT code to move out common pieces and addition of a
new RV32G BPF JIT compiler, from Luke Nelson.
8) Add gso_size context member to __sk_buff in order to be able to know whether
a given skb is GSO or not, from Willem de Bruijn.
9) Add a new bpf_xdp_output() helper which reuses XDP's existing perf RB output
implementation but can be called from tracepoint programs, from Eelco Chaudron.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the handling of signals in client rxrpc calls made by the afs
filesystem. Ignore signals completely, leaving call abandonment or
connection loss to be detected by timeouts inside AF_RXRPC.
Allowing a filesystem call to be interrupted after the entire request has
been transmitted and an abort sent means that the server may or may not
have done the action - and we don't know. It may even be worse than that
for older servers.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the interruptibility of kernel-initiated client calls so that they're
either only interruptible when they're waiting for a call slot to come
available or they're not interruptible at all. Either way, they're not
interruptible during transmission.
This should help prevent StoreData calls from being interrupted when
writeback is in progress. It doesn't, however, handle interruption during
the receive phase.
Userspace-initiated calls are still interruptable. After the signal has
been handled, sendmsg() will return the amount of data copied out of the
buffer and userspace can perform another sendmsg() call to continue
transmission.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2020-03-13
An update from ieee802154 for *net-next*
Two small patches with updates targeting the whole tree.
Sergin does update SPI drivers to the new transfer delay handling
and Gustavo did one of his zero-length array replacement patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In net/Kconfig, NET_DEVLINK implies NET_DROP_MONITOR.
The original behavior of the 'imply' keyword prevents NET_DROP_MONITOR
from being 'm' when NET_DEVLINK=y.
With the planned Kconfig change that relaxes the 'imply', the
combination of NET_DEVLINK=y and NET_DROP_MONITOR=m would be allowed.
Use IS_REACHABLE() to avoid the vmlinux link error for this case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Add relevant getter for ct info dissector.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the zone's flow table instance on the flow action to the drivers.
Thus, allowing drivers to register FT add/del/stats callbacks.
Finally, enable hardware offload on the flow table instance.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver deleted an FT entry, a FT failed to offload, or registered to the
flow table after flows were already added, we still get packets in
software.
For those packets, while restoring the ct state from the flow table
entry, refresh it's hardware offload.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an API to restore the ct state pointer.
This may be used by drivers to restore the ct state if they
miss in tc chain after they already did the hardware connection
tracking action (ct_metadata action).
For example, consider the following rule on chain 0 that is in_hw,
however chain 1 is not_in_hw:
$ tc filter add dev ... chain 0 ... \
flower ... action ct pipe action goto chain 1
Packets of a flow offloaded (via nf flow table offload) by the driver
hit this rule in hardware, will be marked with the ct metadata action
(mark, label, zone) that does the equivalent of the software ct action,
and when the packet jumps to hardware chain 1, there would be a miss.
CT was already processed in hardware. Therefore, the driver's miss
handling should restore the ct state on the skb, using the provided API,
and continue the packet processing in chain 1.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF flow table API associate 5-tuple rule with an action list by calling
the flow table type action() CB to fill the rule's actions.
In action CB of act_ct, populate the ct offload entry actions with a new
ct_metadata action. Initialize the ct_metadata with the ct mark, label and
zone information. If ct nat was performed, then also append the relevant
packet mangle actions (e.g. ipv4/ipv6/tcp/udp header rewrites).
Drivers that offload the ft entries may match on the 5-tuple and perform
the action list.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let drivers to add their cb allowing them to receive flow offload events
of type TC_SETUP_CLSFLOWER (REPLACE/DEL/STATS) for flows managed by the
flow table.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aacd9289af ("tcp: bind() use stronger
condition for bind_conflict") introduced a restriction to forbid to bind
SO_REUSEADDR enabled sockets to the same (addr, port) tuple in order to
assign ports dispersedly so that we can connect to the same remote host.
The change results in accelerating port depletion so that we fail to bind
sockets to the same local port even if we want to connect to the different
remote hosts.
You can reproduce this issue by following instructions below.
1. # sysctl -w net.ipv4.ip_local_port_range="32768 32768"
2. set SO_REUSEADDR to two sockets.
3. bind two sockets to (localhost, 0) and the latter fails.
Therefore, when ephemeral ports are exhausted, bind(0) should fallback to
the legacy behaviour to enable the SO_REUSEADDR option and make it possible
to connect to different remote (addr, port) tuples.
This patch allows us to bind SO_REUSEADDR enabled sockets to the same
(addr, port) only when net.ipv4.ip_autobind_reuse is set 1 and all
ephemeral ports are exhausted. This also allows connect() and listen() to
share ports in the following way and may break some applications. So the
ip_autobind_reuse is 0 by default and disables the feature.
1. setsockopt(sk1, SO_REUSEADDR)
2. setsockopt(sk2, SO_REUSEADDR)
3. bind(sk1, saddr, 0)
4. bind(sk2, saddr, 0)
5. connect(sk1, daddr)
6. listen(sk2)
If it is set 1, we can fully utilize the 4-tuples, but we should use
IP_BIND_ADDRESS_NO_PORT for bind()+connect() as possible.
The notable thing is that if all sockets bound to the same port have
both SO_REUSEADDR and SO_REUSEPORT enabled, we can bind sockets to an
ephemeral port and also do listen().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
In their .attach callback, mq[prio] only add the qdiscs of the currently
active TX queues to the device's qdisc hash list.
If a user later increases the number of active TX queues, their qdiscs
are not visible via eg. 'tc qdisc show'.
Add a hook to netif_set_real_num_tx_queues() that walks all active
TX queues and adds those which are missing to the hash list.
CC: Eric Dumazet <edumazet@google.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent spurious wake ups, we disable any discovery or advertising
when we enter suspend and restore it when we exit suspend. While paused,
we disable any management requests to modify discovery or advertising.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle LE devices, we must first disable passive scanning and
disconnect all connected devices. Once that is complete, we update the
whitelist and re-enable scanning
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register for PM_SUSPEND_PREPARE and PM_POST_SUSPEND to make sure the
Bluetooth controller is prepared correctly for suspend/resume. Implement
the registration, scheduling and task handling portions only in this
patch.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The intention of this helper was to allow driver to specify one type
that it supports, so not only "any" value would pass. So make the API
more strict and allow driver to pass only 1 bit that is going
to be checked.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put the values into enum and add an enum to define the bits.
Suggested-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the check to see if the passed allowed type bit is enabled.
Fixes: 319a1d1947 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of manually iterating over entries, use flow_action_for_each
helper. Move the helper and wrap it to fit to 80 cols on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This splits it into two parts, one that imports the message, and one
that imports the iovec. This allows a caller to only do the first part,
and import the iovec manually afterwards.
No functional changes in this patch.
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add basic psock hooks for UDP sockets. This allows adding and
removing sockets, as well as automatic removal on unhash and close.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-8-lmb@cloudflare.com
The init, close and unhash handlers from TCP sockmap are generic,
and can be reused by UDP sockmap. Move the helpers into the sockmap code
base and expose them. This requires tcp_bpf_get_proto and tcp_bpf_clone to
be conditional on BPF_STREAM_PARSER.
The moved functions are unmodified, except that sk_psock_unlink is
renamed to sock_map_unlink to better match its behaviour.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-6-lmb@cloudflare.com
tcp_bpf.c is only included in the build if CONFIG_NET_SOCK_MSG is
selected. The declaration should therefore be guarded as such.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-5-lmb@cloudflare.com
We need to ensure that sk->sk_prot uses certain callbacks, so that
code that directly calls e.g. tcp_sendmsg in certain corner cases
works. To avoid spurious asserts, we must to do this only if
sk_psock_update_proto has not yet been called. The same invariants
apply for tcp_bpf_check_v6_needs_rebuild, so move the call as well.
Doing so allows us to merge tcp_bpf_init and tcp_bpf_reinit.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-4-lmb@cloudflare.com
The sock map code checks that a socket does not have an active upper
layer protocol before inserting it into the map. This requires casting
via inet_csk, which isn't valid for UDP sockets.
Guard checks for ULP by checking inet_sk(sk)->is_icsk first.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-2-lmb@cloudflare.com
Currently, user who is adding an action expects HW to report stats,
however it does not have exact expectations about the stats types.
That is aligned with TCA_ACT_HW_STATS_TYPE_ANY.
Allow user to specify the type of HW stats for an action and require it.
Pass the information down to flow_offload layer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new type for disabled HW stats and allow the value in
mlxsw offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new type for delayed HW stats and allow the value in
mlx5 offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new type for immediate HW stats and allow the value in
mlxsw offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially, pass "ANY" (struct is zeroed) to the drivers as that is the
current implicit value coming down to flow_offload. Add a bool
indicating that entries have mixed HW stats type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make it safe to have the code upstream without affecting
stable systems since there are a few details not sort out with ECRED
mode e.g: how to initiate multiple connections at once.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the initial code for Enhanced Credit Based Mode which
introduces a new socket mode called L2CAP_MODE_EXT_FLOWCTL, which for
the most part work the same as L2CAP_MODE_LE_FLOWCTL but uses different
PDUs to setup the connections and also works over BR/EDR.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This introduces the definitions for the new L2CAP mode called Enhanced
Credit Based Mode.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Invoke ndo_setup_tc() as appropriate to signal init / replacement,
destroying and dumping of pFIFO / bFIFO Qdisc.
A lot of the FIFO logic is used for pFIFO_head_drop as well, but that's a
semantically very different Qdisc that isn't really in the same boat as
pFIFO / bFIFO. Split some of the functions to keep the Qdisc intact.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realign a comment after the change introduced by the
previous patch.
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable pie_vars->accu_prob is used as an accumulator for
probability values. Since probabilty values are scaled using the
MAX_PROB macro denoting (2^64 - 1), pie_vars->accu_prob is
likely to overflow as it is of type u64.
The variable pie_vars->accu_prob_overflows counts the number of
times the variable pie_vars->accu_prob overflows.
The MAX_PROB macro needs to be equal to at least (2^39 - 1) in
order to do precise calculations without any underflow. Thus
MAX_PROB can be reduced to (2^56 - 1) without affecting the
precision in calculations drastically. Doing so will eliminate
the need for the variable pie_vars->accu_prob_overflows as the
variable pie_vars->accu_prob will never overflow.
Removing the variable pie_vars->accu_prob_overflows also reduces
the size of the structure pie_vars to exactly 64 bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ambiguity by using the term backlog instead of qlen when
representing the queue length in bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the NF flow tables infrastructure for CT offload.
Create a nf flow table per zone.
Next patches will add FT entries to this table, and do
the software offload.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing netlink policy entry for FRA_TUN_ID.
Fixes: e7030878fc ("fib: Add fib rule match on tunnel id")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-02-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 41 non-merge commits during the last 7 day(s) which contain
a total of 49 files changed, 1383 insertions(+), 499 deletions(-).
The main changes are:
1) BPF and Real-Time nicely co-exist.
2) bpftool feature improvements.
3) retrieve bpf_sk_storage via INET_DIAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
So the scm_stat_{add,del} helper can be invoked with no
additional lock held.
This clean-up the code a bit and will make the next
patch easier.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch provides a mechanism for MGMT interface client to query the
capability of the controller to support WBS.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change simply fixes a few typos in the quirk definitions.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.
As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).
So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds INET_DIAG support to bpf_sk_storage.
1. Although this series adds bpf_sk_storage diag capability to inet sk,
bpf_sk_storage is in general applicable to all fullsock. Hence, the
bpf_sk_storage logic will operate on SK_DIAG_* nlattr. The caller
will pass in its specific nesting nlattr (e.g. INET_DIAG_*) as
the argument.
2. The request will be like:
INET_DIAG_REQ_SK_BPF_STORAGES (nla_nest) (defined in latter patch)
SK_DIAG_BPF_STORAGE_REQ_MAP_FD (nla_put_u32)
SK_DIAG_BPF_STORAGE_REQ_MAP_FD (nla_put_u32)
......
Considering there could have multiple bpf_sk_storages in a sk,
instead of reusing INET_DIAG_INFO ("ss -i"), the user can select
some specific bpf_sk_storage to dump by specifying an array of
SK_DIAG_BPF_STORAGE_REQ_MAP_FD.
If no SK_DIAG_BPF_STORAGE_REQ_MAP_FD is specified (i.e. an empty
INET_DIAG_REQ_SK_BPF_STORAGES), it will dump all bpf_sk_storages
of a sk.
3. The reply will be like:
INET_DIAG_BPF_SK_STORAGES (nla_nest) (defined in latter patch)
SK_DIAG_BPF_STORAGE (nla_nest)
SK_DIAG_BPF_STORAGE_MAP_ID (nla_put_u32)
SK_DIAG_BPF_STORAGE_MAP_VALUE (nla_reserve_64bit)
SK_DIAG_BPF_STORAGE (nla_nest)
SK_DIAG_BPF_STORAGE_MAP_ID (nla_put_u32)
SK_DIAG_BPF_STORAGE_MAP_VALUE (nla_reserve_64bit)
......
4. Unlike other INET_DIAG info of a sk which is pretty static, the size
required to dump the bpf_sk_storage(s) of a sk is dynamic as the
system adding more bpf_sk_storage_map. It is hard to set a static
min_dump_alloc size.
Hence, this series learns it at the runtime and adjust the
cb->min_dump_alloc as it iterates all sk(s) of a system. The
"unsigned int *res_diag_size" in bpf_sk_storage_diag_put()
is for this purpose.
The next patch will update the cb->min_dump_alloc as it
iterates the sk(s).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225230421.1975729-1-kafai@fb.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cookie argument to devlink_trap_report() allowing driver to pass in
the user cookie. Pass on the cookie down to drop monitor code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver passed along the cookie, push it through Netlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow driver to indicate cookie metadata for registered traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct flow_action_entry in order to hold TC action cookie
specified by user inserting the action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=x0rf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A new set of changes:
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Special handling is needed in bareudp module for IP & MPLS as they
support more than one ethertypes.
MPLS has 2 ethertypes. 0x8847 for MPLS unicast and 0x8848 for MPLS multicast.
While decapsulating MPLS packet from UDP packet the tunnel destination IP
address is checked to determine the ethertype. The ethertype of the packet
will be set to 0x8848 if the tunnel destination IP address is a multicast
IP address. The ethertype of the packet will be set to 0x8847 if the
tunnel destination IP address is a unicast IP address.
IP has 2 ethertypes.0x0800 for IPV4 and 0x86dd for IPv6. The version
field of the IP header tunnelled will be checked to determine the ethertype.
This special handling to tunnel additional ethertypes will be disabled
by default and can be enabled using a flag called multiproto. This flag can
be used only with ethertypes 0x8847 and 0x0800.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bareudp tunnel module provides a generic L3 encapsulation
tunnelling module for tunnelling different protocols like MPLS,
IP,NSH etc inside a UDP tunnel.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during ACL
processing.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement drv_set_tid_config api to allow TID specific
configuration and drv_reset_tid_config api to reset peer
specific TID configuration. This per-TID onfiguration
will be applied for all the connected stations when MAC is NULL.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-7-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID RTSCTS control
configuration to enable/disable through the
NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-5-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID AMPDU control
configuration to enable/disable aggregation through the
NL80211_TID_CONFIG_ATTR_AMPDU_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-4-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID retry configuration
through the NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes. This TID specific
retry configuration will have more precedence than phy level
configuration.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-3-git-send-email-tamizhr@codeaurora.org
[rebase completely on top of my previous API changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the new NL80211_CMD_SET_TID_CONFIG command to support
data TID specific configuration. Per TID configuration is
passed in the nested NL80211_ATTR_TID_CONFIG attribute.
This patch adds support to configure per TID noack policy
through the NL80211_TID_CONFIG_ATTR_NOACK attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-2-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "reg_notifier" was already documented above the definition of
struct wiphy. The comment inside the definition of the struct did not
bring more information.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-6-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "perm_addr" was already documented above the definition of
struct wiphy. Comments were almost identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-5-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "_net" was already documented above the definition of struct
wiphy. Both comments were identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-4-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Field "registered" was documented three times: twice in the
documentation block of struct wiphy and once inside the struct
definition. This patch keep only one comment.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-3-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "privid" was already documented above the definition of struct
wiphy. Comments were not identical, but they said more or less the same
thing.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-2-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "probe_resp_offload" was already documented above the
definition of struct wiphy. Both comments were identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-1-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8c3ed7aa2b.
As Jouni points out, there's really no need for this, since the
RSN pre-authentication frames are normal data frames, not port
control frames (locally).
We can still revert this now since it hasn't actually gone beyond
-next.
Fixes: 8c3ed7aa2b ("nl80211: add src and dst addr attributes for control port tx/rx")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200224101910.b746e263287a.I9eb15d6895515179d50964dec3550c9dc784bb93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-02-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 25 non-merge commits during the last 4 day(s) which contain
a total of 33 files changed, 2433 insertions(+), 161 deletions(-).
The main changes are:
1) Allow for adding TCP listen sockets into sock_map/hash so they can be used
with reuseport BPF programs, from Jakub Sitnicki.
2) Add a new bpf_program__set_attach_target() helper for adding libbpf support
to specify the tracepoint/function dynamically, from Eelco Chaudron.
3) Add bpf_read_branch_records() BPF helper which helps use cases like profile
guided optimizations, from Daniel Xu.
4) Enable bpf_perf_event_read_value() in all tracing programs, from Song Liu.
5) Relax BTF mandatory check if only used for libbpf itself e.g. to process
BTF defined maps, from Andrii Nakryiko.
6) Move BPF selftests -mcpu compilation attribute from 'probe' to 'v3' as it has
been observed that former fails in envs with low memlock, from Yonghong Song.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 736b46027e ("net: Add ID (if needed) to sock_reuseport and expose
reuseport_lock") has introduced lazy generation of reuseport group IDs that
survive group resize.
By comparing the identifier we check if BPF reuseport program is not trying
to select a socket from a BPF map that belongs to a different reuseport
group than the one the packet is for.
Because SOCKARRAY used to be the only BPF map type that can be used with
reuseport BPF, it was possible to delay the generation of reuseport group
ID until a socket from the group was inserted into BPF map for the first
time.
Now that SOCK{MAP,HASH} can be used with reuseport BPF we have two options,
either generate the reuseport ID on map update, like SOCKARRAY does, or
allocate an ID from the start when reuseport group gets created.
This patch takes the latter approach to keep sockmap free of calls into
reuseport code. This streamlines the reuseport_id access as its lifetime
now matches the longevity of reuseport object.
The cost of this simplification, however, is that we allocate reuseport IDs
for all SO_REUSEPORT users. Even those that don't use SOCKARRAY in their
setups. With the way identifiers are currently generated, we can have at
most S32_MAX reuseport groups, which hopefully is sufficient. If we ever
get close to the limit, we can switch an u64 counter like sk_cookie.
Another change is that we now always call into SOCKARRAY logic to unlink
the socket from the map when unhashing or closing the socket. Previously we
did it only when at least one socket from the group was in a BPF map.
It is worth noting that this doesn't conflict with sockmap tear-down in
case a socket is in a SOCK{MAP,HASH} and belongs to a reuseport
group. sockmap tear-down happens first:
prot->unhash
`- tcp_bpf_unhash
|- tcp_bpf_remove
| `- while (sk_psock_link_pop(psock))
| `- sk_psock_unlink
| `- sock_map_delete_from_link
| `- __sock_map_delete
| `- sock_map_unref
| `- sk_psock_put
| `- sk_psock_drop
| `- rcu_assign_sk_user_data(sk, NULL)
`- inet_unhash
`- reuseport_detach_sock
`- bpf_sk_reuseport_detach
`- WRITE_ONCE(sk->sk_user_data, NULL)
Suggested-by: Martin Lau <kafai@fb.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200218171023.844439-10-jakub@cloudflare.com
Prepare for cloning listening sockets that have their protocol callbacks
overridden by sk_msg. Child sockets must not inherit parent callbacks that
access state stored in sk_user_data owned by the parent.
Restore the child socket protocol callbacks before it gets hashed and any
of the callbacks can get invoked.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200218171023.844439-4-jakub@cloudflare.com
sk_user_data can hold a pointer to an object that is not intended to be
shared between the parent socket and the child that gets a pointer copy on
clone. This is the case when sk_user_data points at reference-counted
object, like struct sk_psock.
One way to resolve it is to tag the pointer with a no-copy flag by
repurposing its lowest bit. Based on the bit-flag value we clear the child
sk_user_data pointer after cloning the parent socket.
The no-copy flag is stored in the pointer itself as opposed to externally,
say in socket flags, to guarantee that the pointer and the flag are copied
from parent to child socket in an atomic fashion. Parent socket state is
subject to change while copying, we don't hold any locks at that time.
This approach relies on an assumption that sk_user_data holds a pointer to
an object aligned at least 2 bytes. A manual audit of existing users of
rcu_dereference_sk_user_data helper confirms our assumption.
Also, an RCU-protected sk_user_data is not likely to hold a pointer to a
char value or a pathological case of "struct { char c; }". To be safe, warn
when the flag-bit is set when setting sk_user_data to catch any future
misuses.
It is worth considering why clearing sk_user_data unconditionally is not an
option. There exist users, DRBD, NVMe, and Xen drivers being among them,
that rely on the pointer being copied when cloning the listening socket.
Potentially we could distinguish these users by checking if the listening
socket has been created in kernel-space via sock_create_kern, and hence has
sk_kern_sock flag set. However, this is not the case for NVMe and Xen
drivers, which create sockets without marking them as belonging to the
kernel.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200218171023.844439-3-jakub@cloudflare.com
Functions starting with __ usually indicate those which are exported,
but should not be called directly. Update some of those declared in the
API and make it more readable.
page_pool_unmap_page() and page_pool_release_page() were doing
exactly the same thing calling __page_pool_clean_page(). Let's
rename __page_pool_clean_page() to page_pool_release_page() and
export it in order to show up on perf logs and get rid of
page_pool_unmap_page().
Finally rename __page_pool_put_page() to page_pool_put_page() since we
can now directly call it from drivers and rename the existing
page_pool_put_page() to page_pool_put_full_page() since they do the same
thing but the latter is trying to sync the full DMA area.
This patch also updates netsec, mvneta and stmmac drivers which use
those functions.
Suggested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ingress and cls_act qdiscs init, save the block on ingress
mini_Qdisc and and pass it on to ingress classification, so it
can be used for the looking up a specified chain index.
Co-developed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
TC multi chain configuration can cause offloaded tc chains to miss in
hardware after jumping to some chain. In such cases the software should
continue from the chain that missed in hardware, as the hardware may
have manipulated the packet and updated some counters.
Currently a single tcf classification function serves both ingress and
egress. However, multi chain miss processing (get tc skb extension on
hw miss, set tc skb extension on tc miss) should happen only on
ingress.
Refactor the code to use ingress classification function, and move setting
the tc skb extension from general classification to it, as a prestep
for supporting the hw miss scenario.
Co-developed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reuse the L2CAP MTU auto logic to select the MTU used for RFCOMM
channels, this should increase the maximum from 1013 to 1021 when 3-DH5
is supported.
Since it does not set an L2CAP MTU we no longer need a debugfs so that
is removed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Several network drivers for chips that support TSO6 share the same code
for preparing the TCP header, so let's factor it out to a helper.
A difference is that some drivers reset the payload_len whilst others
don't do this. This value is overwritten by TSO anyway, therefore
the new helper resets it in general.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The esp fill trailer method is identical for both
IPv6 and IPv4.
Share the implementation for esp6 and esp to avoid
code duplication in addition it could be also used
at various drivers code.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a new API for start/end binary array brackets [] to force array
around binary data as required from JSON. With this restriction, re-open
API to set binary fmsg data.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
tc flower rules that are based on src or dst port blocking are sometimes
ineffective due to uninitialized stack data. __skb_flow_dissect() extracts
ports from the skb for tc flower to match against. However, the port
dissection is not done when when the FLOW_DIS_IS_FRAGMENT bit is set in
key_control->flags. All callers of __skb_flow_dissect(), zero-out the
key_control field except for fl_classify() as used by the flower
classifier. Thus, the FLOW_DIS_IS_FRAGMENT may be set on entry to
__skb_flow_dissect(), since key_control is allocated on the stack
and may not be initialized.
Since key_basic and key_control are present for all flow keys, let's
make sure they are initialized.
Fixes: 62230715fd ("flow_dissector: do not dissect l4 ports for fragments")
Co-developed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor tc_setup_flow_action() function not to use rtnl lock and remove
'rtnl_held' argument that is no longer needed.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove rtnl lock dependency from flow_action representation
translator, change rtnl_dereference() to rcu_dereference_protected() in ct
action helpers that provide external access to zone and action values. This
is safe to do because the functions are not called from anywhere else
outside flow_action infrastructure which was modified to obtain tcf_lock
when accessing action data in one of previous patches in the series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove rtnl lock dependency from flow_action representation
translator, change rcu_dereference_bh_rtnl() to rcu_dereference_protected()
in police action helpers that provide external access to rate and burst
values. This is safe to do because the functions are not called from
anywhere else outside flow_action infrastructure which was modified to
obtain tcf_lock when accessing action data in one of previous patches in
the series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove dependency on rtnl lock, take action's tcfa_lock when
constructing its representation as flow_action_entry structure.
Refactor tcf_sample_get_group() to assume that caller holds tcf_lock and
don't take it manually. This callback is only called from flow_action infra
representation translator which now calls it with tcf_lock held, so this
refactoring is necessary to prevent deadlock.
Allocate memory with GFP_ATOMIC flag for ip_tunnel_info copy because
tcf_tunnel_info_copy() is only called from flow_action representation infra
code with tcf_lock spinlock taken.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix all kernel-doc warnings for <net/sock.h>.
Fixes these warnings:
../include/net/sock.h:232: warning: Function parameter or member 'skc_addrpair' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_portpair' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_ipv6only' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_net_refcnt' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_v6_daddr' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_v6_rcv_saddr' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_cookie' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_listener' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_tw_dr' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_rcv_wnd' not described in 'sock_common'
../include/net/sock.h:232: warning: Function parameter or member 'skc_tw_rcv_nxt' not described in 'sock_common'
../include/net/sock.h:498: warning: Function parameter or member 'sk_rx_skb_cache' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_wq_raw' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'tcp_rtx_queue' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_tx_skb_cache' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_route_forced_caps' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_txtime_report_errors' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_validate_xmit_skb' not described in 'sock'
../include/net/sock.h:498: warning: Function parameter or member 'sk_bpf_storage' not described in 'sock'
../include/net/sock.h:2024: warning: No description found for return value of 'sk_wmem_alloc_get'
../include/net/sock.h:2035: warning: No description found for return value of 'sk_rmem_alloc_get'
../include/net/sock.h:2046: warning: No description found for return value of 'sk_has_allocations'
../include/net/sock.h:2082: warning: No description found for return value of 'skwq_has_sleeper'
../include/net/sock.h:2244: warning: No description found for return value of 'sk_page_frag'
../include/net/sock.h:2444: warning: Function parameter or member 'tcp_rx_skb_cache_key' not described in 'DECLARE_STATIC_KEY_FALSE'
../include/net/sock.h:2444: warning: Excess function parameter 'sk' description in 'DECLARE_STATIC_KEY_FALSE'
../include/net/sock.h:2444: warning: Excess function parameter 'skb' description in 'DECLARE_STATIC_KEY_FALSE'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds BT_PHY socket option (read-only) which can be used to read
the PHYs in use by the underline connection.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* avoid running out of tracking space for frames that need
to be reported to userspace by using more bits
* fix beacon handling suppression by adding some relevant
elements to the CRC calculation
* fix quiet mode in action frames
* fix crash in ethtool for virt_wifi and similar
* add a missing policy entry
* fix 160 & 80+80 bandwidth to take local capabilities into
account
-----BEGIN PGP SIGNATURE-----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=L+Ik
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* avoid running out of tracking space for frames that need
to be reported to userspace by using more bits
* fix beacon handling suppression by adding some relevant
elements to the CRC calculation
* fix quiet mode in action frames
* fix crash in ethtool for virt_wifi and similar
* add a missing policy entry
* fix 160 & 80+80 bandwidth to take local capabilities into
account
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a mac80211 driver can only set the txq_limit when using
wake_tx_queue. Not all drivers use wake_tx_queue. This patch adds a new
element to wiphy allowing a driver to set a custom tx_queue_len and the
code that will apply it in case it is set. The current default is
1000 which is too low for ath11k when doing HE rates.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200211122605.13002-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
@thoff has moved to struct flow_dissector_key_control.
Fixes: 42aecaa9bb ("net: Get skb hash over flow_keys structure")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regulatory domain might forbid HE operation. Certain regulatory
domains may restrict it for specific channels whereas others may do it
for the whole regulatory domain.
Add an option to indicate it in the channel flag.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200121081213.733757-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It turns out that this wasn't a good idea, I hit a test failure in
hwsim due to this. That particular failure was easily worked around,
but it raised questions: if an AP needs to, for example, send action
frames to each connected station, the current limit is nowhere near
enough (especially if those stations are sleeping and the frames are
queued for a while.)
Shuffle around some bits to make more room for ack_frame_id to allow
up to 8192 queued up frames, that's enough for queueing 4 frames to
each connected station, even at the maximum of 2007 stations on a
single AP.
We take the bits from band (which currently only 2 but I leave 3 in
case we add another band) and from the hw_queue, which can only need
4 since it has a limit of 16 queues.
Fixes: 6912daed05 ("mac80211: Shrink the size of ack_frame_id to make room for tx_time_est")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20200115122549.b9a4ef9f4980.Ied52ed90150220b83a280009c590b65d125d087c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot managed to send an IPX packet through bond_alb_xmit()
and af_packet and triggered a use-after-free.
First, bond_alb_xmit() was using ipx_hdr() helper to reach
the IPX header, but ipx_hdr() was using the transport offset
instead of the network offset. In the particular syzbot
report transport offset was 0xFFFF
This patch removes ipx_hdr() since it was only (mis)used from bonding.
Then we need to make sure IPv4/IPv6/IPX headers are pulled
in skb->head before dereferencing anything.
BUG: KASAN: use-after-free in bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
Read of size 2 at addr ffff8801ce56dfff by task syz-executor.2/18108
(if (ipx_hdr(skb)->ipx_checksum != IPX_NO_CHECKSUM) ...)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
[<ffffffff8441fc42>] __dump_stack lib/dump_stack.c:17 [inline]
[<ffffffff8441fc42>] dump_stack+0x14d/0x20b lib/dump_stack.c:53
[<ffffffff81a7dec4>] print_address_description+0x6f/0x20b mm/kasan/report.c:282
[<ffffffff81a7e0ec>] kasan_report_error mm/kasan/report.c:380 [inline]
[<ffffffff81a7e0ec>] kasan_report mm/kasan/report.c:438 [inline]
[<ffffffff81a7e0ec>] kasan_report.cold+0x8c/0x2a0 mm/kasan/report.c:422
[<ffffffff81a7dc4f>] __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:469
[<ffffffff82c8c00a>] bond_alb_xmit+0x153a/0x1590 drivers/net/bonding/bond_alb.c:1452
[<ffffffff82c60c74>] __bond_start_xmit drivers/net/bonding/bond_main.c:4199 [inline]
[<ffffffff82c60c74>] bond_start_xmit+0x4f4/0x1570 drivers/net/bonding/bond_main.c:4224
[<ffffffff83baa558>] __netdev_start_xmit include/linux/netdevice.h:4525 [inline]
[<ffffffff83baa558>] netdev_start_xmit include/linux/netdevice.h:4539 [inline]
[<ffffffff83baa558>] xmit_one net/core/dev.c:3611 [inline]
[<ffffffff83baa558>] dev_hard_start_xmit+0x168/0x910 net/core/dev.c:3627
[<ffffffff83bacf35>] __dev_queue_xmit+0x1f55/0x33b0 net/core/dev.c:4238
[<ffffffff83bae3a8>] dev_queue_xmit+0x18/0x20 net/core/dev.c:4278
[<ffffffff84339189>] packet_snd net/packet/af_packet.c:3226 [inline]
[<ffffffff84339189>] packet_sendmsg+0x4919/0x70b0 net/packet/af_packet.c:3252
[<ffffffff83b1ac0c>] sock_sendmsg_nosec net/socket.c:673 [inline]
[<ffffffff83b1ac0c>] sock_sendmsg+0x12c/0x160 net/socket.c:684
[<ffffffff83b1f5a2>] __sys_sendto+0x262/0x380 net/socket.c:1996
[<ffffffff83b1f700>] SYSC_sendto net/socket.c:2008 [inline]
[<ffffffff83b1f700>] SyS_sendto+0x40/0x60 net/socket.c:2004
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MPTCP=y, CONFIG_MPTCP_IPV6=n, and CONFIG_IPV6=m:
ERROR: "mptcp_handle_ipv6_mapped" [net/ipv6/ipv6.ko] undefined!
This does not happen if CONFIG_MPTCP_IPV6=y, as CONFIG_MPTCP_IPV6
selects CONFIG_IPV6, and thus forces CONFIG_IPV6 builtin.
As exporting a symbol for an empty function would be a bit wasteful, fix
this by providing a dummy version of mptcp_handle_ipv6_mapped() for the
CONFIG_MPTCP_IPV6=n case.
Rename mptcp_handle_ipv6_mapped() to mptcpv6_handle_mapped(), to make it
clear this is a pure-IPV6 function, just like mptcpv6_init().
Fixes: cec37a6e41 ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6cd021a58c ("udp: segment looped gso packets correctly")
fixes an issue with rare udp gso multicast packets looped onto the
receive path.
The stable backport makes the narrowest change to target only these
packets, when needed. As opposed to, say, expanding __udp_gso_segment,
which is harder to reason to be free from unintended side-effects.
But the resulting code is hardly self-describing.
Document its purpose and rationale.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast and broadcast packets can be looped from egress to ingress
pre segmentation with dev_loopback_xmit. That function unconditionally
sets ip_summed to CHECKSUM_UNNECESSARY.
udp_rcv_segment segments gso packets in the udp rx path. Segmentation
usually executes on egress, and does not expect packets of this type.
__udp_gso_segment interprets !CHECKSUM_PARTIAL as CHECKSUM_NONE. But
the offsets are not correct for gso_make_checksum.
UDP GSO packets are of type CHECKSUM_PARTIAL, with their uh->check set
to the correct pseudo header checksum. Reset ip_summed to this type.
(CHECKSUM_PARTIAL is allowed on ingress, see comments in skbuff.h)
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: cf329aa42b ("udp: cope with UDP GRO packet misdirection")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info "fw.roce".
v2: Remove board.nvm_cfg since fw.psid is similar.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-01-26
Here's (probably) the last bluetooth-next pull request for the 5.6 kernel.
- Initial pieces of Bluetooth 5.2 Isochronous Channels support
- mgmt: Various cleanups and a new Set Blocked Keys command
- btusb: Added support for 04ca:3021 QCA_ROME device
- hci_qca: Multiple fixes & cleanups
- hci_bcm: Fixes & improved device tree support
- Fixed attempts to create duplicate debugfs entries
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends UDP GRO to support fraglist GRO/GSO
by using the previously introduced infrastructure.
If the feature is enabled, all UDP packets are going to
fraglist GRO (local input and forward).
After validating the csum, we mark ip_summed as
CHECKSUM_UNNECESSARY for fraglist GRO packets to
make sure that the csum is not touched.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementations of ops->bind_class() are merely
searching for classid and updating class in the struct tcf_result,
without invoking either of cl_ops->bind_tcf() or
cl_ops->unbind_tcf(). This breaks the design of them as qdisc's
like cbq use them to count filters too. This is why syzbot triggered
the warning in cbq_destroy_class().
In order to fix this, we have to call cl_ops->bind_tcf() and
cl_ops->unbind_tcf() like the filter binding path. This patch does
so by refactoring out two helper functions __tcf_bind_filter()
and __tcf_unbind_filter(), which are lockless and accept a Qdisc
pointer, then teaching each implementation to call them correctly.
Note, we merely pass the Qdisc pointer as an opaque pointer to
each filter, they only need to pass it down to the helper
functions without understanding it at all.
Fixes: 07d79fc7d9 ("net_sched: add reverse binding for tc class")
Reported-and-tested-by: syzbot+0a0596220218fcb603a8@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+63bdb6006961d8c917c6@syzkaller.appspotmail.com
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new set type allows for intervals in concatenated fields,
which are expressed in the usual way, that is, simple byte
concatenation with padding to 32 bits for single fields, and
given as ranges by specifying start and end elements containing,
each, the full concatenation of start and end values for the
single fields.
Ranges are expanded to composing netmasks, for each field: these
are inserted as rules in per-field lookup tables. Bits to be
classified are divided in 4-bit groups, and for each group, the
lookup table contains 4^2 buckets, representing all the possible
values of a bit group. This approach was inspired by the Grouper
algorithm:
http://www.cse.usf.edu/~ligatti/projects/grouper/
Matching is performed by a sequence of AND operations between
bucket values, with buckets selected according to the value of
packet bits, for each group. The result of this sequence tells
us which rules matched for a given field.
In order to concatenate several ranged fields, per-field rules
are mapped using mapping arrays, one per field, that specify
which rules should be considered while matching the next field.
The mapping array for the last field contains a reference to
the element originally inserted.
The notes in nft_set_pipapo.c cover the algorithm in deeper
detail.
A pure hash-based approach is of no use here, as ranges need
to be classified. An implementation based on "proxying" the
existing red-black tree set type, creating a tree for each
field, was considered, but deemed impractical due to the fact
that elements would need to be shared between trees, at least
as long as we want to keep UAPI changes to a minimum.
A stand-alone implementation of this algorithm is available at:
https://pipapo.lameexcu.se
together with notes about possible future optimisations
(in pipapo.c).
This algorithm was designed with data locality in mind, and can
be highly optimised for SIMD instruction sets, as the bulk of
the matching work is done with repetitive, simple bitwise
operations.
At this point, without further optimisations, nft_concat_range.sh
reports, for one AMD Epyc 7351 thread (2.9GHz, 512 KiB L1D$, 8 MiB
L2$):
TEST: performance
net,port [ OK ]
baseline (drop from netdev hook): 10190076pps
baseline hash (non-ranged entries): 6179564pps
baseline rbtree (match on first field only): 2950341pps
set with 1000 full, ranged entries: 2304165pps
port,net [ OK ]
baseline (drop from netdev hook): 10143615pps
baseline hash (non-ranged entries): 6135776pps
baseline rbtree (match on first field only): 4311934pps
set with 100 full, ranged entries: 4131471pps
net6,port [ OK ]
baseline (drop from netdev hook): 9730404pps
baseline hash (non-ranged entries): 4809557pps
baseline rbtree (match on first field only): 1501699pps
set with 1000 full, ranged entries: 1092557pps
port,proto [ OK ]
baseline (drop from netdev hook): 10812426pps
baseline hash (non-ranged entries): 6929353pps
baseline rbtree (match on first field only): 3027105pps
set with 30000 full, ranged entries: 284147pps
net6,port,mac [ OK ]
baseline (drop from netdev hook): 9660114pps
baseline hash (non-ranged entries): 3778877pps
baseline rbtree (match on first field only): 3179379pps
set with 10 full, ranged entries: 2082880pps
net6,port,mac,proto [ OK ]
baseline (drop from netdev hook): 9718324pps
baseline hash (non-ranged entries): 3799021pps
baseline rbtree (match on first field only): 1506689pps
set with 1000 full, ranged entries: 783810pps
net,mac [ OK ]
baseline (drop from netdev hook): 10190029pps
baseline hash (non-ranged entries): 5172218pps
baseline rbtree (match on first field only): 2946863pps
set with 1000 full, ranged entries: 1279122pps
v4:
- fix build for 32-bit architectures: 64-bit division needs
div_u64() (kbuild test robot <lkp@intel.com>)
v3:
- rework interface for field length specification,
NFT_SET_SUBKEY disappears and information is stored in
description
- remove scratch area to store closing element of ranges,
as elements now come with an actual attribute to specify
the upper range limit (Pablo Neira Ayuso)
- also remove pointer to 'start' element from mapping table,
closing key is now accessible via extension data
- use bytes right away instead of bits for field lengths,
this way we can also double the inner loop of the lookup
function to take care of upper and lower bits in a single
iteration (minor performance improvement)
- make it clearer that set operations are actually atomic
API-wise, but we can't e.g. implement flush() as one-shot
action
- fix type for 'dup' in nft_pipapo_insert(), check for
duplicates only in the next generation, and in general take
care of differentiating generation mask cases depending on
the operation (Pablo Neira Ayuso)
- report C implementation matching rate in commit message, so
that AVX2 implementation can be compared (Pablo Neira Ayuso)
v2:
- protect access to scratch maps in nft_pipapo_lookup() with
local_bh_disable/enable() (Florian Westphal)
- drop rcu_read_lock/unlock() from nft_pipapo_lookup(), it's
already implied (Florian Westphal)
- explain why partial allocation failures don't need handling
in pipapo_realloc_scratch(), rename 'm' to clone and update
related kerneldoc to make it clear we're not operating on
the live copy (Florian Westphal)
- add expicit check for priv->start_elem in
nft_pipapo_insert() to avoid ending up in nft_pipapo_walk()
with a NULL start element, and also zero it out in every
operation that might make it invalid, so that insertion
doesn't proceed with an invalid element (Florian Westphal)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce a new nested netlink attribute, NFTA_SET_DESC_CONCAT, used
to specify the length of each field in a set concatenation.
This allows set implementations to support concatenation of multiple
ranged items, as they can divide the input key into matching data for
every single field. Such set implementations would be selected as
they specify support for NFT_SET_INTERVAL and allow desc->field_count
to be greater than one. Explicitly disallow this for nft_set_rbtree.
In order to specify the interval for a set entry, userspace would
include in NFTA_SET_DESC_CONCAT attributes field lengths, and pass
range endpoints as two separate keys, represented by attributes
NFTA_SET_ELEM_KEY and NFTA_SET_ELEM_KEY_END.
While at it, export the number of 32-bit registers available for
packet matching, as nftables will need this to know the maximum
number of field lengths that can be specified.
For example, "packets with an IPv4 address between 192.0.2.0 and
192.0.2.42, with destination port between 22 and 25", can be
expressed as two concatenated elements:
NFTA_SET_ELEM_KEY: 192.0.2.0 . 22
NFTA_SET_ELEM_KEY_END: 192.0.2.42 . 25
and NFTA_SET_DESC_CONCAT attribute would contain:
NFTA_LIST_ELEM
NFTA_SET_FIELD_LEN: 4
NFTA_LIST_ELEM
NFTA_SET_FIELD_LEN: 2
v4: No changes
v3: Complete rework, NFTA_SET_DESC_CONCAT instead of NFTA_SET_SUBKEY
v2: No changes
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add NFTA_SET_ELEM_KEY_END attribute to convey the closing element of the
interval between kernel and userspace.
This patch also adds the NFT_SET_EXT_KEY_END extension to store the
closing element value in this interval.
v4: No changes
v3: New patch
[sbrivio: refactor error paths and labels; add corresponding
nft_set_ext_type for new key; rebase]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Invoke ndo_setup_tc as appropriate to signal init / replacement, destroying
and dumping of TBF Qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to initialise the struct ourselves, else we expose tcp-specific
callbacks such as tcp_splice_read which will then trigger splat because
the socket is an mptcp one:
BUG: KASAN: slab-out-of-bounds in tcp_mstamp_refresh+0x80/0xa0 net/ipv4/tcp_output.c:57
Write of size 8 at addr ffff888116aa21d0 by task syz-executor.0/5478
CPU: 1 PID: 5478 Comm: syz-executor.0 Not tainted 5.5.0-rc6 #3
Call Trace:
tcp_mstamp_refresh+0x80/0xa0 net/ipv4/tcp_output.c:57
tcp_rcv_space_adjust+0x72/0x7f0 net/ipv4/tcp_input.c:612
tcp_read_sock+0x622/0x990 net/ipv4/tcp.c:1674
tcp_splice_read+0x20b/0xb40 net/ipv4/tcp.c:791
do_splice+0x1259/0x1560 fs/splice.c:1205
To prevent build error with ipv6, add the recv/sendmsg function
declaration to ipv6.h. The functions are already accessible "thanks"
to retpoline related work, but they are currently only made visible
by socket.c specific INDIRECT_CALLABLE macros.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a list of pending module requests. This new module
list is composed of nft_module_request objects that contain the module
name and one status field that tells if the module has been already
loaded (the 'done' field).
In the first pass, from the preparation phase, the netlink command finds
that a module is missing on this list. Then, a module request is
allocated and added to this list and nft_request_module() returns
-EAGAIN. This triggers the abort path with the autoload parameter set on
from nfnetlink, request_module() is called and the module request enters
the 'done' state. Since the mutex is released when loading modules from
the abort phase, the module list is zapped so this is iteration occurs
over a local list. Therefore, the request_module() calls happen when
object lists are in consistent state (after fulling aborting the
transaction) and the commit list is empty.
On the second pass, the netlink command will find that it already tried
to load the module, so it does not request it again and
nft_request_module() returns 0. Then, there is a look up to find the
object that the command was missing. If the module was successfully
loaded, the command proceeds normally since it finds the missing object
in place, otherwise -ENOENT is reported to userspace.
This patch also updates nfnetlink to include the reason to enter the
abort phase, which is required for this new autoload module rationale.
Fixes: ec7470b834 ("netfilter: nf_tables: store transaction list locally while requesting module")
Reported-by: syzbot+29125d208b3dae9a7019@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This implements MP_CAPABLE options parsing and writing according
to RFC 6824 bis / RFC 8684: MPTCP v1.
Local key is sent on syn/ack, and both keys are sent on 3rd ack.
MP_CAPABLE messages len are updated accordingly. We need the skbuff to
correctly emit the above, so we push the skbuff struct as an argument
all the way from tcp code to the relevant mptcp callbacks.
When processing incoming MP_CAPABLE + data, build a full blown DSS-like
map info, to simplify later processing. On child socket creation, we
need to record the remote key, if available.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parses incoming DSS options and populates outgoing MPTCP ACK
fields. MPTCP fields are parsed from the TCP option header and placed in
an skb extension, allowing the upper MPTCP layer to access MPTCP
options after the skb has gone through the TCP stack.
The subflow implements its own data_ready() ops, which ensures that the
pending data is in sequence - according to MPTCP seq number - dropping
out-of-seq skbs. The DATA_READY bit flag is set if this is the case.
This allows the MPTCP socket layer to determine if more data is
available without having to consult the individual subflows.
It additionally validates the current mapping and propagates EoF events
to the connection socket.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Co-developed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-packet metadata required to write the MPTCP DSS option is written to
the skb_ext area. One write to the socket may contain more than one
packet of data, which is copied to page fragments and mapped in to MPTCP
DSS segments with size determined by the available page fragments and
the maximum mapping length allowed by the MPTCP specification. If
do_tcp_sendpages() splits a DSS segment in to multiple skbs, that's ok -
the later skbs can either have duplicated DSS mapping information or
none at all, and the receiver can handle that.
The current implementation uses the subflow frag cache and tcp
sendpages to avoid excessive code duplication. More work is required to
ensure that it works correctly under memory pressure and to support
MPTCP-level retransmissions.
The MPTCP DSS checksum is not yet implemented.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to tcp_output.c to add MP_CAPABLE to an outgoing SYN request,
to capture the MP_CAPABLE in the received SYN-ACK, to add MP_CAPABLE to
the final ACK of the three-way handshake.
Use the .sk_rx_dst_set() handler in the subflow proto to capture when the
responding SYN-ACK is received and notify the MPTCP connection layer.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to parse and format the MP_CAPABLE option.
This option is handled according to MPTCP version 0 (RFC6824).
MPTCP version 1 MP_CAPABLE (RFC6824bis/RFC8684) will be added later in
coordination with related code changes.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the infrastructure for MPTCP sockets.
MPTCP sockets open one in-kernel TCP socket per subflow. These subflow
sockets are only managed by the MPTCP socket that owns them and are not
visible from userspace. This commit allows a userspace program to open
an MPTCP socket with:
sock = socket(AF_INET, SOCK_STREAM, IPPROTO_MPTCP);
The resulting socket is simply a wrapper around a single regular TCP
socket, without any of the MPTCP protocol implemented over the wire.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Principles:
- Packets are classified on flows.
- This is a Stochastic model (as we use a hash, several flows might
be hashed to the same slot)
- Each flow has a PIE managed queue.
- Flows are linked onto two (Round Robin) lists,
so that new flows have priority on old ones.
- For a given flow, packets are not reordered.
- Drops during enqueue only.
- ECN capability is off by default.
- ECN threshold (if ECN is enabled) is at 10% by default.
- Uses timestamps to calculate queue delay by default.
Usage:
tc qdisc ... fq_pie [ limit PACKETS ] [ flows NUMBER ]
[ target TIME ] [ tupdate TIME ]
[ alpha NUMBER ] [ beta NUMBER ]
[ quantum BYTES ] [ memory_limit BYTES ]
[ ecnprob PERCENTAGE ] [ [no]ecn ]
[ [no]bytemode ] [ [no_]dq_rate_estimator ]
defaults:
limit: 10240 packets, flows: 1024
target: 15 ms, tupdate: 15 ms (in jiffies)
alpha: 1/8, beta : 5/4
quantum: device MTU, memory_limit: 32 Mb
ecnprob: 10%, ecn: off
bytemode: off, dq_rate_estimator: off
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: V. Saicharan <vsaicharan1998@gmail.com>
Signed-off-by: Mohit Bhasi <mohitbhasi1998@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the drop_early(), calculate_probability() and
pie_process_dequeue() functions generic enough to be used by
both PIE and FQ-PIE (to be added in a future commit). The major
change here is in the way the functions take in arguments. This
patch exports these functions and makes FQ-PIE dependent on
sch_pie.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the comments along with the commenting style used to
describe the members of the structures and their initial values
in the init functions.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the members of the structure such that closely
referenced members appear together and/or fit in the same
cacheline. Also, change the order of their initializations to
match the order in which they appear in the structure.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux best practice recommends using u8 for true/false values in
structures.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange macros in order of length and align the values to
improve readability.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the U64_MAX macro to denote the constant (2^64 - 1).
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves macros, structures and small functions common
to PIE and FQ-PIE (to be added in a future commit) from the file
net/sched/sch_pie.c to the header file include/net/pie.h.
All the moved functions are made inline.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-01-22
The following pull-request contains BPF updates for your *net-next* tree.
We've added 92 non-merge commits during the last 16 day(s) which contain
a total of 320 files changed, 7532 insertions(+), 1448 deletions(-).
The main changes are:
1) function by function verification and program extensions from Alexei.
2) massive cleanup of selftests/bpf from Toke and Andrii.
3) batched bpf map operations from Brian and Yonghong.
4) tcp congestion control in bpf from Martin.
5) bulking for non-map xdp_redirect form Toke.
6) bpf_send_signal_thread helper from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP sockets use the default implementation of struct sock's
sk_data_ready callback, which is sock_def_readable(). This function
is called in the XDP socket fast-path, and involves a retpoline. By
letting sock_def_readable() have external linkage, and being called
directly, the retpoline can be avoided.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200120092917.13949-1-bjorn.topel@gmail.com
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2020-01-21
1) Add support for TCP encapsulation of IKE and ESP messages,
as defined by RFC 8229. Patchset from Sabrina Dubroca.
Please note that there is a merge conflict in:
net/unix/af_unix.c
between commit:
3c32da19a8 ("unix: Show number of pending scm files of receive queue in fdinfo")
from the net-next tree and commit:
b50b0580d2 ("net: add queue argument to __skb_wait_for_more_packets and __skb_{,try_}recv_datagram")
from the ipsec-next tree.
The conflict can be solved as done in linux-next.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet trap that can report NVE packets that the device decided to
drop because their overlay source MAC is multicast.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during tunnel
decapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet trap that can report packets that reached the router, but are
non-routable. For example, IGMP queries can be flooded by the device in
layer 2 and reach the router. Such packets should not be routed and
instead dropped.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) Incorrect uapi header comment in bitwise, from Jeremy Sowden.
2) Fetch flow statistics if flow is still active.
3) Restrict flow matching on hardware based on input device.
4) Add nf_flow_offload_work_alloc() helper function.
5) Remove the last client of the FLOW_OFFLOAD_DYING flag, use teardown
instead.
6) Use atomic bitwise operation to operate with flow flags.
7) Add nf_flowtable_hw_offload() helper function to check for the
NF_FLOWTABLE_HW_OFFLOAD flag.
8) Add NF_FLOW_HW_REFRESH to retry hardware offload from the flowtable
software datapath.
9) Remove indirect calls in xt_hashlimit, from Florian Westphal.
10) Add nf_flow_offload_tuple() helper to consolidate code.
11) Add nf_flow_table_offload_cmd() helper function.
12) A few whitespace cleanups in nf_tables in bitwise and the bitmap/hash
set types, from Jeremy Sowden.
13) Cleanup netlink attribute checks in bitwise, from Jeremy Sowden.
14) Replace goto by return in error path of nft_bitwise_dump(), from
Jeremy Sowden.
15) Add bitwise operation netlink attribute, also from Jeremy.
16) Add nft_bitwise_init_bool(), from Jeremy Sowden.
17) Add nft_bitwise_eval_bool(), also from Jeremy.
18) Add nft_bitwise_dump_bool(), from Jeremy Sowden.
19) Disallow hardware offload for other that NFT_BITWISE_BOOL,
from Jeremy Sowden.
20) Add NFTA_BITWISE_DATA netlink attribute, again from Jeremy.
21) Add support for bitwise shift operation, from Jeremy Sowden.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark function parameters as 'const' where possible.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nf_flow_offload_add() fails to add the flow to hardware, then the
NF_FLOW_HW_REFRESH flag bit is set and the flow remains in the flowtable
software path.
If flowtable hardware offload is enabled, this patch enqueues a new
request to offload this flow to hardware.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This function checks for the NF_FLOWTABLE_HW_OFFLOAD flag, meaning that
the flowtable hardware offload is enabled.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Originally, all flow flag bits were set on only from the workqueue. With
the introduction of the flow teardown state and hardware offload this is
no longer true. Let's be safe and use atomic bitwise operation to
operation with flow flags.
Fixes: 59c466dd68 ("netfilter: nf_flow_table: add a new flow state for tearing down offloading")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The dying bit removes the conntrack entry if the netdev that owns this
flow is going down. Instead, use the teardown mechanism to push back the
flow to conntrack to let the classic software path decide what to do
with it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Daniel Borkmann says:
====================
pull-request: bpf 2020-01-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 9 day(s) which contain
a total of 13 files changed, 95 insertions(+), 43 deletions(-).
The main changes are:
1) Fix refcount leak for TCP time wait and request sockets for socket lookup
related BPF helpers, from Lorenz Bauer.
2) Fix wrong verification of ARSH instruction under ALU32, from Daniel Borkmann.
3) Batch of several sockmap and related TLS fixes found while operating
more complex BPF programs with Cilium and OpenSSL, from John Fastabend.
4) Fix sockmap to read psock's ingress_msg queue before regular sk_receive_queue()
to avoid purging data upon teardown, from Lingpeng Chen.
5) Fix printing incorrect pointer in bpftool's btf_dump_ptr() in order to properly
dump a BPF map's value with BTF, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When sockmap sock with TLS enabled is removed we cleanup bpf/psock state
and call tcp_update_ulp() to push updates to TLS ULP on top. However, we
don't push the write_space callback up and instead simply overwrite the
op with the psock stored previous op. This may or may not be correct so
to ensure we don't overwrite the TLS write space hook pass this field to
the ULP and have it fixup the ctx.
This completes a previous fix that pushed the ops through to the ULP
but at the time missed doing this for write_space, presumably because
write_space TLS hook was added around the same time.
Fixes: 95fa145479 ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-4-john.fastabend@gmail.com
This enables passing ISO packets to the monitor socket.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These adds the HCI definitions for handling CIS connections along with
ISO data packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MGMT command is added to receive the list of blocked keys from
user-space.
The list is used to:
1) Block keys from being distributed by the device during
the ke distribution phase of SMP.
2) Filter out any keys that were previously saved so
they are no longer used.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* -O3 enablement fallout, thanks to Arnd who ran this
* fixes for a few leaks, thanks to Felix
* channel 12 regulatory fix for custom regdomains
* check for a crash reported by syzbot
(NULL function is called on drivers that don't have it)
* fix TKIP replay protection after setup with some APs
(from Jouni)
* restrict obtaining some mesh data to avoid WARN_ONs
* fix deadlocks with auto-disconnect (socket owner)
* fix radar detection events with multiple devices
-----BEGIN PGP SIGNATURE-----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=i20C
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-01-15' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few fixes:
* -O3 enablement fallout, thanks to Arnd who ran this
* fixes for a few leaks, thanks to Felix
* channel 12 regulatory fix for custom regdomains
* check for a crash reported by syzbot
(NULL function is called on drivers that don't have it)
* fix TKIP replay protection after setup with some APs
(from Jouni)
* restrict obtaining some mesh data to avoid WARN_ONs
* fix deadlocks with auto-disconnect (socket owner)
* fix radar detection events with multiple devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the attributes, policy and parsing code to allow userland
to send the info about the BSS coloring settings to the kernel.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-1-john@phrozen.org
[johannes: remove the strict policy parsing, that was a misunderstanding]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a similar fashion to previous patch, add "offload" and "trap"
indication to IPv6 routes.
This is done by using two unused bits in 'struct fib6_info' to hold
these indications. Capable drivers are expected to set these when
processing the various in-kernel route notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing L3 offload, routes and nexthops are usually programmed
into two different tables in the underlying device. Therefore, the fact
that a nexthop resides in hardware does not necessarily mean that all
the associated routes also reside in hardware and vice-versa.
While the kernel can signal to user space the presence of a nexthop in
hardware (via 'RTNH_F_OFFLOAD'), it does not have a corresponding flag
for routes. In addition, the fact that a route resides in hardware does
not necessarily mean that the traffic is offloaded. For example,
unreachable routes (i.e., 'RTN_UNREACHABLE') are programmed to trap
packets to the CPU so that the kernel will be able to generate the
appropriate ICMP error packet.
This patch adds an "offload" and "trap" indications to IPv4 routes, so
that users will have better visibility into the offload process.
'struct fib_alias' is extended with two new fields that indicate if the
route resides in hardware or not and if it is offloading traffic from
the kernel or trapping packets to it. Note that the new fields are added
in the 6 bytes hole and therefore the struct still fits in a single
cache line [1].
Capable drivers are expected to invoke fib_alias_hw_flags_set() with the
route's key in order to set the flags.
The indications are dumped to user space via a new flags (i.e.,
'RTM_F_OFFLOAD' and 'RTM_F_TRAP') in the 'rtm_flags' field in the
ancillary header.
v2:
* Make use of 'struct fib_rt_info' in fib_alias_hw_flags_set()
[1]
struct fib_alias {
struct hlist_node fa_list; /* 0 16 */
struct fib_info * fa_info; /* 16 8 */
u8 fa_tos; /* 24 1 */
u8 fa_type; /* 25 1 */
u8 fa_state; /* 26 1 */
u8 fa_slen; /* 27 1 */
u32 tb_id; /* 28 4 */
s16 fa_default; /* 32 2 */
u8 offload:1; /* 34: 0 1 */
u8 trap:1; /* 34: 1 1 */
u8 unused:6; /* 34: 2 1 */
/* XXX 5 bytes hole, try to pack */
struct callback_head rcu __attribute__((__aligned__(8))); /* 40 16 */
/* size: 56, cachelines: 1, members: 12 */
/* sum members: 50, holes: 1, sum holes: 5 */
/* sum bitfield members: 8 bits (1 bytes) */
/* forced alignments: 1, forced holes: 1, sum forced holes: 5 */
/* last cacheline: 56 bytes */
} __attribute__((__aligned__(8)));
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_dump_info() is used to prepare RTM_{NEW,DEL}ROUTE netlink messages
using the passed arguments. Currently, the function takes 11 arguments,
6 of which are attributes of the route being dumped (e.g., prefix, TOS).
The next patch will need the function to also dump to user space an
indication if the route is present in hardware or not. Instead of
passing yet another argument, change the function to take a struct
containing the different route attributes.
v2:
* Name last argument of fib_dump_info()
* Move 'struct fib_rt_info' to include/net/ip_fib.h so that it could
later be passed to fib_alias_hw_flags_set()
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to call macsec_pn_wrapped from hardware drivers to notify when a
PN rolls over. Some drivers might used an interrupt to implement this.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces MACsec ops for drivers to support offloading
MACsec operations.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the macsec_context structure. It will be used
in the kernel to exchange information between the common MACsec
implementation (macsec.c) and the MACsec hardware offloading
implementations. This structure contains pointers to MACsec specific
structures which contain the actual MACsec configuration, and to the
underlying device (phydev for now).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves some structure, type and identifier definitions into a
MACsec specific header. This patch does not modify how the MACsec code
is running and only move things around. This is a preparation for the
future MACsec hardware offloading support, which will re-use those
definitions outside macsec.c.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the documentation for devlink into a subfolder, and provide an
index.rst file that can be used to generally describe devlink.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fw.psid" devlink info version is documented in devlink-info.rst,
and used by one driver. However, there is no associated macro for this
firmware version like there is for others. Add one now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we will find stray/unexpected/old extensions value on next
iteration.
On tcp_write_xmit() we can end-up splitting an already queued skb in two
parts, via tso_fragment(). The newly created skb can be allocated via
the tx cache and an upper layer will not be aware of it, so that upper
layer cannot set the ext properly.
Resetting the ext on recycle ensures that stale data is not propagated
in to packet headers or elsewhere.
An alternative would be add an additional hook in tso_fragment() or in
sk_stream_alloc_skb() to init the ext for upper layers that need it.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPTCP will make use of tcp_send_mss() and tcp_push() when sending
data to specific TCP subflows.
tcp_request_sock_ipvX_ops and ipvX_specific will be referenced
during TCP subflow creation.
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce and collapse of packets carrying MPTCP extensions is allowed
when the newer packet has no extension or the extensions carried by both
packets are equal.
This allows merging of TSO packet trains and even cross-TSO packets, and
does not require any additional action when moving data into existing
SKBs.
v3 -> v4:
- allow collapsing, under mptcp_skb_can_collapse() constraint
v5 -> v6:
- clarify MPTCP skb extensions must always be cleared at allocation
time
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enum value for MPTCP and update config dependencies
v5 -> v6:
- fixed '__unused' field size
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ULP is used on a listening socket, icsk_ulp_ops and icsk_ulp_data are
copied when the listener is cloned. Sometimes the clone is immediately
deleted, which will invoke the release op on the clone and likely
corrupt the listening socket's icsk_ulp_data.
The clone operation is invoked immediately after the clone is copied and
gives the ULP type an opportunity to set up the clone socket and its
icsk_ulp_data.
The MPTCP ULP clone will silently fallback to plain TCP on allocation
failure, so 'clone()' does not need to return an error code.
v6 -> v7:
- move and rename ulp clone helper to make it inline-friendly
v5 -> v6:
- clarified MPTCP clone usage in commit message
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP option 30 is allocated for MPTCP by the IANA.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match the 16-bit width of skbuff->protocol. Fills an 8-bit hole so
sizeof(struct sock) does not change.
Also take care of BPF field access for sk_type/sk_protocol. Both of them
are now outside the bitfield, so we can use load instructions without
further shifting/masking.
v5 -> v6:
- update eBPF accessors, too (Intel's kbuild test robot)
v2 -> v3:
- keep 'sk_type' 2 bytes aligned (Eric)
v1 -> v2:
- preserve sk_pacing_shift as bit field (Eric)
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: bpf@vger.kernel.org
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_PROTOCOL_MAX is only used in two places, for DECNet and AX.25. The
limits have more to do with the those protocol definitions than they do
with the data type of sk_protocol, so remove SK_PROTOCOL_MAX and use
U8_MAX directly.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes "struct tcp_congestion_ops" to be the first user
of BPF STRUCT_OPS. It allows implementing a tcp_congestion_ops
in bpf.
The BPF implemented tcp_congestion_ops can be used like
regular kernel tcp-cc through sysctl and setsockopt. e.g.
[root@arch-fb-vm1 bpf]# sysctl -a | egrep congestion
net.ipv4.tcp_allowed_congestion_control = reno cubic bpf_cubic
net.ipv4.tcp_available_congestion_control = reno bic cubic bpf_cubic
net.ipv4.tcp_congestion_control = bpf_cubic
There has been attempt to move the TCP CC to the user space
(e.g. CCP in TCP). The common arguments are faster turn around,
get away from long-tail kernel versions in production...etc,
which are legit points.
BPF has been the continuous effort to join both kernel and
userspace upsides together (e.g. XDP to gain the performance
advantage without bypassing the kernel). The recent BPF
advancements (in particular BTF-aware verifier, BPF trampoline,
BPF CO-RE...) made implementing kernel struct ops (e.g. tcp cc)
possible in BPF. It allows a faster turnaround for testing algorithm
in the production while leveraging the existing (and continue growing)
BPF feature/framework instead of building one specifically for
userspace TCP CC.
This patch allows write access to a few fields in tcp-sock
(in bpf_tcp_ca_btf_struct_access()).
The optional "get_info" is unsupported now. It can be added
later. One possible way is to output the info with a btf-id
to describe the content.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200109003508.3856115-1-kafai@fb.com
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that a reporter recovery completion do not finish
successfully when recovery is triggered via
devlink_health_reporter_recover as recovery could be processed in
different context. In such scenario an error is returned by driver when
recover hook is invoked and successful recovery completion is
intimated later.
Expose devlink recover done API to update recovery stats.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing netns context in arp_tables, from Florian Westphal.
2) Underflow in flowtable reference counter, from wenxu.
3) Fix incorrect ethernet destination address in flowtable offload,
from wenxu.
4) Check for status of neighbour entry, from wenxu.
5) Fix NAT port mangling, from wenxu.
6) Unbind callbacks from destroy path to cleanup hardware properly
on flowtable removal.
7) Fix missing casting statistics timestamp, add nf_flowtable_time_stamp
and use it.
8) NULL pointer exception when timeout argument is null in conntrack
dccp and sctp protocol helpers, from Florian Westphal.
9) Possible nul-dereference in ipset with IPSET_ATTR_LINENO, also from
Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds nf_flowtable_time_stamp and updates the existing code to
use it.
This patch is also implicitly fixing up hardware statistic fetching via
nf_flow_offload_stats() where casting to u32 is missing. Use
nf_flow_timeout_delta() to fix this.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
The DSA drivers that implement .phylink_mac_link_state should normally
register an interrupt for the PCS, from which they should call
phylink_mac_change(). However not all switches implement this, and those
who don't should set this flag in dsa_switch in the .setup callback, so
that PHYLINK will poll for a few ms until the in-band AN link timer
expires and the PCS state settles.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles LE PHY Update Complete event and store both tx_phy and
rx_phy into hci_conn.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The macro is really not needed and can be replaced with either usage of
bt_err_ratelimited or bt_dev_err_ratelimited.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The macro will be used to display rate limited warning messages in the
log.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit 275c44aa19.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa19 ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8b ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f80 ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b16
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b16
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc40 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b16
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b16
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b8 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the purpose of route offload, when a single route is deleted, it is
only of interest if it is the first route in the node or if it is
sibling to such a route.
In the first case, distinguish between several possibilities:
1. Route is the last route in the node. Emit a delete notification
2. Route is followed by a non-multipath route. Emit a replace
notification for the non-multipath route.
3. Route is followed by a multipath route. Emit a replace notification
for the multipath route.
In the second case, only emit a delete notification to ensure the route
is no longer used as a valid nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to simplify the IPv6 route offload API,
which will only use three events - replace, delete and append.
Introduce a temporary version of replace and delete in order to make the
conversion easier to review. Note that append does not need a temporary
version, as it is currently not used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
So disable the neigh confirm for vxlan and geneve pmtu update.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function skb_dst_update_pmtu_no_confirm() for callers who need
update pmtu but should not do neighbor confirm.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
When storing a pointer to a dst_metrics structure in dst_entry._metrics,
two flags are added in the least significant bits of the pointer value.
Hence this assumes all pointers to dst_metrics structures have at least
4-byte alignment.
However, on m68k, the minimum alignment of 32-bit values is 2 bytes, not
4 bytes. Hence in some kernel builds, dst_default_metrics may be only
2-byte aligned, leading to obscure boot warnings like:
WARNING: CPU: 0 PID: 7 at lib/refcount.c:28 refcount_warn_saturate+0x44/0x9a
refcount_t: underflow; use-after-free.
Modules linked in:
CPU: 0 PID: 7 Comm: ksoftirqd/0 Tainted: G W 5.5.0-rc2-atari-01448-g114a1a1038af891d-dirty #261
Stack from 10835e6c:
10835e6c 0038134f 00023fa6 00394b0f 0000001c 00000009 00321560 00023fea
00394b0f 0000001c 001a70f8 00000009 00000000 10835eb4 00000001 00000000
04208040 0000000a 00394b4a 10835ed4 00043aa8 001a70f8 00394b0f 0000001c
00000009 00394b4a 0026aba8 003215a4 00000003 00000000 0026d5a8 00000001
003215a4 003a4361 003238d6 000001f0 00000000 003215a4 10aa3b00 00025e84
003ddb00 10834000 002416a8 10aa3b00 00000000 00000080 000aa038 0004854a
Call Trace: [<00023fa6>] __warn+0xb2/0xb4
[<00023fea>] warn_slowpath_fmt+0x42/0x64
[<001a70f8>] refcount_warn_saturate+0x44/0x9a
[<00043aa8>] printk+0x0/0x18
[<001a70f8>] refcount_warn_saturate+0x44/0x9a
[<0026aba8>] refcount_sub_and_test.constprop.73+0x38/0x3e
[<0026d5a8>] ipv4_dst_destroy+0x5e/0x7e
[<00025e84>] __local_bh_enable_ip+0x0/0x8e
[<002416a8>] dst_destroy+0x40/0xae
Fix this by forcing 4-byte alignment of all dst_metrics structures.
Fixes: e5fd387ad5 ("ipv6: do not overwrite inetpeer metrics prematurely")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag format used in Atheros AR9331 built-in switch.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of xsk_umem_discard_addr to xsk_umem_release_addr to
better reflect the new naming of the AF_XDP queue manipulation
functions. As this functions is used by drivers implementing support
for AF_XDP zero-copy, it requires a name change to these drivers. The
function xsk_umem_release_addr_rq has also changed name in the same
fashion.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-10-git-send-email-magnus.karlsson@intel.com
Change the names of the validation functions to better reflect what
they are doing. The uppermost ones are reading entries from the rings
and only the bottom ones validate entries. So xskq_cons_read_ is a
better prefix name.
Also change the xskq_cons_read_ functions to return a bool
as the the descriptor or address is already returned by reference
in the parameters. Everyone is using the return value as a bool
anyway.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-9-git-send-email-magnus.karlsson@intel.com
The xskmap flush list is used to track entries that need to flushed
from via the xdp_do_flush_map() function. This list used to be
per-map, but there is really no reason for that. Instead make the
flush list global for all xskmaps, which simplifies __xsk_map_flush()
and xsk_map_alloc().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-5-bjorn.topel@gmail.com
There is currently no way for driver to reliably check that
the socket it has looked up is in fact RX offloaded. Add
a helper. This allows drivers to catch misbehaving firmware.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks at appropriate points to make it possible to offload the ETS
Qdisc.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit about negating HW backlog left me scratching my head. Clarify the
comment.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_pacing_shift can be read and written without lock
synchronization. This patch adds annotations to
document this fact and avoid future syzbot complains.
This might also avoid unexpected false sharing
in sk_pacing_shift_update(), as the compiler
could remove the conditional check and always
write over sk->sk_pacing_shift :
if (sk->sk_pacing_shift != val)
sk->sk_pacing_shift = val;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).
This triggered a warning in the 64 bit optimized ipv6_addr_is_*() functions
because sparse doesn't know that the buffer already points to some data in
the correct bitwise integer format. But these were correct and can
therefore be marked with __force to signalize sparse an intended cast to a
specific bitwise type.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).
This triggered a warning in ipv6_get_dsfield() because sparse doesn't know
that the buffer already points to some data in the correct bitwise integer
format. This was already fixed in ipv6_change_dsfield() by the __force
attribute and can be fixed here the same way.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to how tcp_sendmsg() is implemented, we can have an empty
skb at the tail of the write queue.
Most [1] tcp_write_queue_empty() callers want to know if there is
anything to send (payload and/or FIN)
Instead of checking if the sk_write_queue is empty, we need
to test if tp->write_seq == tp->snd_nxt
[1] tcp_send_fin() was the only caller that expected to
see if an skb was in the write queue, I have changed the code
to reuse the tcp_write_queue_tail() result.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Michal Kubecek and Firo Yang did a very nice analysis of crashes
happening in __inet_lookup_established().
Since a TCP socket can go from TCP_ESTABLISH to TCP_LISTEN
(via a close()/socket()/listen() cycle) without a RCU grace period,
I should not have changed listeners linkage in their hash table.
They must use the nulls protocol (Documentation/RCU/rculist_nulls.txt),
so that a lookup can detect a socket in a hash list was moved in
another one.
Since we added code in commit d296ba60d8 ("soreuseport: Resolve
merge conflict for v4/v6 ordering fix"), we have to add
hlist_nulls_add_tail_rcu() helper.
Fixes: 3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/netdev/20191120083919.GH27852@unicorn.suse.cz/
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds a new transmit path for hardware that supports 802.11
encapsulation offloading. In those cases 802.3 frames get passed
directly to the driver allowing the hardware to handle the encapsulation.
Some features such as monitor mode and TKIP would break when encapsulation
offloading is enabled. If any of these get enabled, the code will alwyas
fallback to the normal sw encapsulation data path.
The patch defines a secondary netdev_ops struct that the device gets
assigned if 802.11 encap support is available and enabled. The driver
needs to enable the support on a per vif basis if it finds that all
pre-reqs are meet.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191125100438.16539-1-john@phrozen.org
[reword comments, remove SUPPORTS_80211_ENCAP HW flag, minor cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Function nl80211_validate_nested() is not specific to nl80211, it's
a counterpart to nla_validate_nested_deprecated() with strict validation.
For consistency with other validation and parse functions, rename it to
nla_validate_nested().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unix sockets like a block box. You never know what is stored there:
there may be a file descriptor holding a mount or a block device,
or there may be whole universes with namespaces, sockets with receive
queues full of sockets etc.
The patch adds a little debug and accounts number of files (not recursive),
which is in receive queue of a unix socket. Sometimes this is useful
to determine, that socket should be investigated or which task should
be killed to put reference counter on a resourse.
v2: Pass correct argument to lockdep
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to register a transport able to handle
local communication (loopback).
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a sysctl knob "net.ipv4.tcp_no_ssthresh_metrics_save"
that disables TCP ssthresh metrics cache by default. Other parts of TCP
metrics cache, e.g. rtt, cwnd, remain unchanged.
As modern networks becoming more and more dynamic, TCP metrics cache
today often causes more harm than benefits. For example, the same IP
address is often shared by different subscribers behind NAT in residential
networks. Even if the IP address is not shared by different users,
caching the slow-start threshold of a previous short flow using loss-based
congestion control (e.g. cubic) often causes the future longer flows of
the same network path to exit slow-start prematurely with abysmal
throughput.
Caching ssthresh is very risky and can lead to terrible performance.
Therefore it makes sense to make disabling ssthresh caching by
default and opt-in for specific networks by the administrators.
This practice also has worked well for several years of deployment with
CUBIC congestion control at Google.
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
This is needed, because if the flag X25_ACCPT_APPRV_FLAG is not set on a
socket (manual call confirmation) and the channel is cleared by remote
before the manual call confirmation was sent, this situation needs to
be handled.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_cleanup() has not been used for seven years, and was a wrong design.
Messing with shared pointer in bond_neigh_init() without proper
memory barriers would at least trigger syzbot complains eventually.
It is time to remove this stuff.
Fixes: b63b70d877 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP encapsulation of IKE and IPsec messages (RFC 8229) is implemented
as a TCP ULP, overriding in particular the sendmsg and recvmsg
operations. A Stream Parser is used to extract messages out of the TCP
stream using the first 2 bytes as length marker. Received IKE messages
are put on "ike_queue", waiting to be dequeued by the custom recvmsg
implementation. Received ESP messages are sent to XFRM, like with UDP
encapsulation.
Some of this code is taken from the original submission by Herbert
Xu. Currently, only IPv4 is supported, like for UDP encapsulation.
Co-developed-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be used by TCP encapsulation to write packets to the encap
socket without holding the user socket's lock. Without this reinjection,
we're already holding the lock of the user socket, and then try to lock
the encap socket as well when we enqueue the encrypted packet.
While at it, add a BUILD_BUG_ON like we usually do for skb->cb, since
it's missing for struct xfrm_trans_cb.
Co-developed-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e2 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies == 2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(2147484649, 1000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(2147484649, 120000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit
cca9bab1b7 ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes: cca9bab1b7 ("tcp: use monotonic timestamps for PAWS")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 5c72299fba ("net: sched: cls_flower: Classify
packets using port ranges") had added filtering based on port ranges
to tc flower. However the commit missed necessary changes in hw-offload
code, so the feature gave rise to generating incorrect offloaded flow
keys in NIC.
One more detailed example is below:
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 100-200 action drop
With the setup above, an exact match filter with dst_port == 0 will be
installed in NIC by hw-offload. IOW, the NIC will have a rule which is
equivalent to the following one.
$ tc qdisc add dev eth0 ingress
$ tc filter add dev eth0 ingress protocol ip flower ip_proto tcp \
dst_port 0 action drop
The behavior was caused by the flow dissector which extracts packet
data into the flow key in the tc flower. More specifically, regardless
of exact match or specified port ranges, fl_init_dissector() set the
FLOW_DISSECTOR_KEY_PORTS flag in struct flow_dissector to extract port
numbers from skb in skb_flow_dissect() called by fl_classify(). Note
that device drivers received the same struct flow_dissector object as
used in skb_flow_dissect(). Thus, offloaded drivers could not identify
which of these is used because the FLOW_DISSECTOR_KEY_PORTS flag was
set to struct flow_dissector in either case.
This patch adds the new FLOW_DISSECTOR_KEY_PORTS_RANGE flag and the new
tp_range field in struct fl_flow_key to recognize which filters are applied
to offloaded drivers. At this point, when filters based on port ranges
passed to drivers, drivers return the EOPNOTSUPP error because they do
not support the feature (the newly created FLOW_DISSECTOR_KEY_PORTS_RANGE
flag).
Fixes: 5c72299fba ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Partially sent record cleanup path increments an SG entry
directly instead of using sg_next(). This should not be a
problem today, as encrypted messages should be always
allocated as arrays. But given this is a cleanup path it's
easy to miss was this ever to change. Use sg_next(), and
simplify the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like when BPF support was added by commit d3b18ad31f
("tls: add bpf support to sk_msg handling") and
commit d829e9c411 ("tls: convert to generic sk_msg interface")
it broke/removed the support for in-place crypto as added by
commit 4e6d47206c ("tls: Add support for inplace records
encryption").
The inplace_crypto member of struct tls_rec is dead, inited
to zero, and sometimes set to zero again. It used to be
set to 1 when record was allocated, but the skmsg code doesn't
seem to have been written with the idea of in-place crypto
in mind.
Since non trivial effort is required to bring the feature back
and we don't really have the HW to measure the benefit just
remove the left over support for now to avoid confusing readers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This is mostly to fix the iwlwifi regression:
1) Flush GRO state properly in iwlwifi driver, from Alexander Lobakin.
2) Validate TIPC link name with properly length macro, from John
Rutherford.
3) Fix completion init and device query timeouts in ibmvnic, from
Thomas Falcon.
4) Fix SKB size calculation for netlink messages in psample, from
Nikolay Aleksandrov.
5) Similar kind of fix for OVS flow dumps, from Paolo Abeni.
6) Handle queue allocation failure unwind properly in gve driver, we
could try to release pages we didn't allocate. From Jeroen de
Borst.
7) Serialize TX queue SKB list accesses properly in mscc ocelot
driver. From Yangbo Lu"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net:
net: usb: aqc111: Use the correct style for SPDX License Identifier
net: phy: Use the correct style for SPDX License Identifier
net: wireless: intel: iwlwifi: fix GRO_NORMAL packet stalling
net: mscc: ocelot: use skb queue instead of skbs list
net: mscc: ocelot: avoid incorrect consuming in skbs list
gve: Fix the queue page list allocated pages count
net: inet_is_local_reserved_port() port arg should be unsigned short
openvswitch: fix flow command message size
net: phy: dp83869: Fix return paths to return proper values
net: psample: fix skb_over_panic
net: usbnet: Fix -Wcast-function-type
net: hso: Fix -Wcast-function-type
net: port < inet_prot_sock(net) --> inet_port_requires_bind_service(net, port)
ibmvnic: Serialize device queries
ibmvnic: Bound waits for device queries
ibmvnic: Terminate waiting device threads after loss of service
ibmvnic: Fix completion structure initialization
net-sctp: replace some sock_net(sk) with just 'net'
net: Fix a documentation bug wrt. ip_unprivileged_port_start
tipc: fix link name length check
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
Any argument outside of that range would result in an out of bound
memory access, since the accessed array is 65536 bits long.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the sysctl write accessor functions guarantee that:
net->ipv4.sysctl_ip_prot_sock <= net->ipv4.ip_local_ports.range[0]
invariant is maintained, and as such the max() in selinux hooks is actually spurious.
ie. even though
if (snum < max(inet_prot_sock(sock_net(sk)), low) || snum > high) {
per logic is the same as
if ((snum < inet_prot_sock(sock_net(sk)) && snum < low) || snum > high) {
it is actually functionally equivalent to:
if (snum < low || snum > high) {
which is equivalent to:
if (snum < inet_prot_sock(sock_net(sk)) || snum < low || snum > high) {
even though the first clause is spurious.
But we want to hold on to it in case we ever want to change what what
inet_port_requires_bind_service() means (for example by changing
it from a, by default, [0..1024) range to some sort of set).
Test: builds, git 'grep inet_prot_sock' finds no other references
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Another merge window, another pull full of stuff:
1) Support alternative names for network devices, from Jiri Pirko.
2) Introduce per-netns netdev notifiers, also from Jiri Pirko.
3) Support MSG_PEEK in vsock/virtio, from Matias Ezequiel Vara
Larsen.
4) Allow compiling out the TLS TOE code, from Jakub Kicinski.
5) Add several new tracepoints to the kTLS code, also from Jakub.
6) Support set channels ethtool callback in ena driver, from Sameeh
Jubran.
7) New SCTP events SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED,
SCTP_ADDR_MADE_PRIM, and SCTP_SEND_FAILED_EVENT. From Xin Long.
8) Add XDP support to mvneta driver, from Lorenzo Bianconi.
9) Lots of netfilter hw offload fixes, cleanups and enhancements,
from Pablo Neira Ayuso.
10) PTP support for aquantia chips, from Egor Pomozov.
11) Add UDP segmentation offload support to igb, ixgbe, and i40e. From
Josh Hunt.
12) Add smart nagle to tipc, from Jon Maloy.
13) Support L2 field rewrite by TC offloads in bnxt_en, from Venkat
Duvvuru.
14) Add a flow mask cache to OVS, from Tonghao Zhang.
15) Add XDP support to ice driver, from Maciej Fijalkowski.
16) Add AF_XDP support to ice driver, from Krzysztof Kazimierczak.
17) Support UDP GSO offload in atlantic driver, from Igor Russkikh.
18) Support it in stmmac driver too, from Jose Abreu.
19) Support TIPC encryption and auth, from Tuong Lien.
20) Introduce BPF trampolines, from Alexei Starovoitov.
21) Make page_pool API more numa friendly, from Saeed Mahameed.
22) Introduce route hints to ipv4 and ipv6, from Paolo Abeni.
23) Add UDP segmentation offload to cxgb4, Rahul Lakkireddy"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1857 commits)
libbpf: Fix usage of u32 in userspace code
mm: Implement no-MMU variant of vmalloc_user_node_flags
slip: Fix use-after-free Read in slip_open
net: dsa: sja1105: fix sja1105_parse_rgmii_delays()
macvlan: schedule bc_work even if error
enetc: add support Credit Based Shaper(CBS) for hardware offload
net: phy: add helpers phy_(un)lock_mdio_bus
mdio_bus: don't use managed reset-controller
ax88179_178a: add ethtool_op_get_ts_info()
mlxsw: spectrum_router: Fix use of uninitialized adjacency index
mlxsw: spectrum_router: After underlay moves, demote conflicting tunnels
bpf: Simplify __bpf_arch_text_poke poke type handling
bpf: Introduce BPF_TRACE_x helper for the tracing tests
bpf: Add bpf_jit_blinding_enabled for !CONFIG_BPF_JIT
bpf, testing: Add various tail call test cases
bpf, x86: Emit patchable direct jump as tail call
bpf: Constant map key tracking for prog array pokes
bpf: Add poke dependency tracking for prog array maps
bpf: Add initial poke descriptor table for jit images
bpf: Move owner type, jited info into array auxiliary data
...
Pull cgroup updates from Tejun Heo:
"There are several notable changes here:
- Single thread migrating itself has been optimized so that it
doesn't need threadgroup rwsem anymore.
- Freezer optimization to avoid unnecessary frozen state changes.
- cgroup ID unification so that cgroup fs ino is the only unique ID
used for the cgroup and can be used to directly look up live
cgroups through filehandle interface on 64bit ino archs. On 32bit
archs, cgroup fs ino is still the only ID in use but it is only
unique when combined with gen.
- selftest and other changes"
* 'for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (24 commits)
writeback: fix -Wformat compilation warnings
docs: cgroup: mm: Fix spelling of "list"
cgroup: fix incorrect WARN_ON_ONCE() in cgroup_setup_root()
cgroup: use cgrp->kn->id as the cgroup ID
kernfs: use 64bit inos if ino_t is 64bit
kernfs: implement custom exportfs ops and fid type
kernfs: combine ino/id lookup functions into kernfs_find_and_get_node_by_id()
kernfs: convert kernfs_node->id from union kernfs_node_id to u64
kernfs: kernfs_find_and_get_node_by_ino() should only look up activated nodes
kernfs: use dumber locking for kernfs_find_and_get_node_by_ino()
netprio: use css ID instead of cgroup ID
writeback: use ino_t for inodes in tracepoints
kernfs: fix ino wrap-around detection
kselftests: cgroup: Avoid the reuse of fd after it is deallocated
cgroup: freezer: don't change task and cgroups status unnecessarily
cgroup: use cgroup->last_bstat instead of cgroup->bstat_pending for consistency
cgroup: remove cgroup_enable_task_cg_lists() optimization
cgroup: pids: use atomic64_t for pids->limit
selftests: cgroup: Run test_core under interfering stress
selftests: cgroup: Add task migration tests
...
This patch is to fix a data-race reported by syzbot:
BUG: KCSAN: data-race in sctp_assoc_migrate / sctp_hash_obj
write to 0xffff8880b67c0020 of 8 bytes by task 18908 on cpu 1:
sctp_assoc_migrate+0x1a6/0x290 net/sctp/associola.c:1091
sctp_sock_migrate+0x8aa/0x9b0 net/sctp/socket.c:9465
sctp_accept+0x3c8/0x470 net/sctp/socket.c:4916
inet_accept+0x7f/0x360 net/ipv4/af_inet.c:734
__sys_accept4+0x224/0x430 net/socket.c:1754
__do_sys_accept net/socket.c:1795 [inline]
__se_sys_accept net/socket.c:1792 [inline]
__x64_sys_accept+0x4e/0x60 net/socket.c:1792
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b67c0020 of 8 bytes by task 12003 on cpu 0:
sctp_hash_obj+0x4f/0x2d0 net/sctp/input.c:894
rht_key_get_hash include/linux/rhashtable.h:133 [inline]
rht_key_hashfn include/linux/rhashtable.h:159 [inline]
rht_head_hashfn include/linux/rhashtable.h:174 [inline]
head_hashfn lib/rhashtable.c:41 [inline]
rhashtable_rehash_one lib/rhashtable.c:245 [inline]
rhashtable_rehash_chain lib/rhashtable.c:276 [inline]
rhashtable_rehash_table lib/rhashtable.c:316 [inline]
rht_deferred_worker+0x468/0xab0 lib/rhashtable.c:420
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
It was caused by rhashtable access asoc->base.sk when sctp_assoc_migrate
is changing its value. However, what rhashtable wants is netns from asoc
base.sk, and for an asoc, its netns won't change once set. So we can
simply fix it by caching netns since created.
Fixes: d6c0256a60 ("sctp: add the rhashtable apis for sctp global transport hashtable")
Reported-by: syzbot+e3b35fe7918ff0ee474e@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In commit a82055af59 ("netfilter: nft_payload: add VLAN offload
support"), VLAN fields in struct flow_dissector_key_vlan were unionized
with the intention of introducing another field that covered the whole TCI
header. However without a wrapping struct the subfields end up sharing the
same bits. As a result, "tc filter add ... flower vlan_id 14" specifies not
only vlan_id, but also vlan_priority.
Fix by wrapping the individual VLAN fields in a struct.
Fixes: a82055af59 ("netfilter: nft_payload: add VLAN offload support")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit added the ability to throttle stations when they queue
too much airtime in the hardware. This commit enables the functionality by
calculating the expected airtime usage of each packet that is dequeued from
the TXQs in mac80211, and accounting that as pending airtime.
The estimated airtime for each skb is stored in the tx_info, so we can
subtract the same amount from the running total when the skb is freed or
recycled. The throttling mechanism relies on this accounting to be
accurate (i.e., that we are not freeing skbs without subtracting any
airtime they were accounted for), so we put the subtraction into
ieee80211_report_used_skb(). As an optimisation, we also subtract the
airtime on regular TX completion, zeroing out the value stored in the
packet afterwards, to avoid having to do an expensive lookup of the station
from the packet data on every packet.
This patch does *not* include any mechanism to wake a throttled TXQ again,
on the assumption that this will happen anyway as a side effect of whatever
freed the skb (most commonly a TX completion).
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-5-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order for the Fq_CoDel algorithm integrated in mac80211 layer to operate
effectively to control excessive queueing latency, the CoDel algorithm
requires an accurate measure of how long packets stays in the queue, AKA
sojourn time. The sojourn time measured at the mac80211 layer doesn't
include queueing latency in the lower layer (firmware/hardware) and CoDel
expects lower layer to have a short queue. However, most 802.11ac chipsets
offload tasks such TX aggregation to firmware or hardware, thus have a deep
lower layer queue.
Without a mechanism to control the lower layer queue size, packets only
stay in mac80211 layer transiently before being sent to firmware queue.
As a result, the sojourn time measured by CoDel in the mac80211 layer is
almost always lower than the CoDel latency target, hence CoDel does little
to control the latency, even when the lower layer queue causes excessive
latency.
The Byte Queue Limits (BQL) mechanism is commonly used to address the
similar issue with wired network interface. However, this method cannot be
applied directly to the wireless network interface. "Bytes" is not a
suitable measure of queue depth in the wireless network, as the data rate
can vary dramatically from station to station in the same network, from a
few Mbps to over Gbps.
This patch implements an Airtime-based Queue Limit (AQL) to make CoDel work
effectively with wireless drivers that utilized firmware/hardware
offloading. AQL allows each txq to release just enough packets to the lower
layer to form 1-2 large aggregations to keep hardware fully utilized and
retains the rest of the frames in mac80211 layer to be controlled by the
CoDel algorithm.
Signed-off-by: Kan Yan <kyan@google.com>
[ Toke: Keep API to set pending airtime internal, fix nits in commit msg ]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-4-kyan@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix recently added code to calculate airtime of packets to the mt76
driver. Import this into mac80211 so we can use it for airtime queue limit
calculations.
The airtime.c file is copied verbatim from the mt76 driver, and adjusted to
be usable in mac80211. This involves:
- Switching to mac80211 data structures.
- Adding support for 160 MHz channels and HE mode.
- Moving the symbol and duration calculations around a bit to avoid
rounding with the higher rates and longer symbol times used for HE rates.
The per-rate TX rate calculation is also split out to its own function so
it can be used directly for the AQL calculations later.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191119060610.76681-3-kyan@google.com
[fix HE_GROUP_IDX() to use 3 * bw, since there are 3 _gi values]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is alike the previous change, with some additional ipv4 specific
quirk. Even when using the route hint we still have to do perform
additional per packet checks about source address validity: a new
helper is added to wrap them.
Hints are explicitly disabled if the destination is a local broadcast,
that keeps the code simple and local broadcast are a slower path anyway.
UDP flood performances vs recvmmsg() receiver:
vanilla patched delta
Kpps Kpps %
1683 1871 +11
In the worst case scenario - each packet has a different
destination address - the performance delta is within noise
range.
v3 -> v4:
- re-enable hints for forward
v2 -> v3:
- really fix build (sic) and hint usage check
- use fib4_has_custom_rules() helpers (David A.)
- add ip_extract_route_hint() helper (Edward C.)
- use prev skb as hint instead of copying data (Willem)
v1 -> v2:
- fix build issue with !CONFIG_IP_MULTIPLE_TABLES
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it in the next patch.
Additionally constify the helper argument.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wraps the namespace field with the same name, to easily
access it regardless of build options.
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the following parameters in order to add the possibility to sync
DMA memory for device before putting allocated pages in the page_pool
caches:
- PP_FLAG_DMA_SYNC_DEV: if set in page_pool_params flags, all pages that
the driver gets from page_pool will be DMA-synced-for-device according
to the length provided by the device driver. Please note DMA-sync-for-CPU
is still device driver responsibility
- offset: DMA address offset where the DMA engine starts copying rx data
- max_len: maximum DMA memory size page_pool is allowed to flush. This
is currently used in __page_pool_alloc_pages_slow routine when pages
are allocated from page allocator
These parameters are supposed to be set by device drivers.
This optimization reduces the length of the DMA-sync-for-device.
The optimization is valid because pages are initially
DMA-synced-for-device as defined via max_len. At RX time, the driver
will perform a DMA-sync-for-CPU on the memory for the packet length.
What is important is the memory occupied by packet payload, because
this is the area CPU is allowed to read and modify. As we don't track
cache-lines written into by the CPU, simply use the packet payload length
as dma_sync_size at page_pool recycle time. This also take into account
any tail-extend.
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_update_nid() to be called by page pool consumers when they
detect numa node changes.
It will update the page pool nid value to start allocating from the new
effective numa node.
This is to mitigate page pool allocating pages from a wrong numa node,
where the pool was originally allocated, and holding on to pages that
belong to a different numa node, which causes performance degradation.
For pages that are already being consumed and could be returned to the
pool by the consumer, in next patch we will add a check per page to avoid
recycling them back to the pool and return them to the page allocator.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match on ethertype and set up protocol dependency. Check for protocol
dependency before accessing the tci field. Allow to match on the
encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload support at this stage assumes an ethernet device in
place. The flow dissector provides the intermediate representation to
express this selector, so extend it to allow to store the interface
type. Flower does not uses this, so skb_flow_dissect_meta() is not
extended to match on this new field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch constifies the pointer to source register data that is passed
as an input parameter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:
tcp_bpf_sendmsg_redir
tcp_bpf_push_locked
tcp_bpf_push
kernel_sendpage_locked
sock->ops->sendpage_locked
Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.
Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af0f ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Jonathan change the page_pool to become responsible to its
own shutdown via deferred work queue, then the disconnect_cnt
counter was removed from xdp memory model tracepoint.
This patch change the page_pool_inflight tracepoint name to
page_pool_release, because it reflects the new responsability
better. And it reintroduces a counter that reflect the number of
times page_pool_release have been tried.
The counter is also used by the code, to only empty the alloc
cache once. With a stuck work queue running every second and
counter being 64-bit, it will overrun in approx 584 billion
years. For comparison, Earth lifetime expectancy is 7.5 billion
years, before the Sun will engulf, and destroy, the Earth.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Wildcard support for the net,iface set from Kristian Evensen.
2) Offload support for matching on the input interface.
3) Simplify matching on vlan header fields.
4) Add nft_payload_rebuild_vlan_hdr() function to rebuild the vlan
header from the vlan sk_buff metadata.
5) Pass extack to nft_flow_cls_offload_setup().
6) Add C-VLAN matching support.
7) Use time64_t in xt_time to fix y2038 overflow, from Arnd Bergmann.
8) Use time_t in nft_meta to fix y2038 overflow, also from Arnd.
9) Add flow_action_entry_next() helper function to flowtable offload
infrastructure.
10) Add IPv6 support to the flowtable offload infrastructure.
11) Support for input interface matching from postrouting,
from Phil Sutter.
12) Missing check for ndo callback in flowtable offload, from wenxu.
13) Remove conntrack parameter from flow_offload_fill_dir(), from wenxu.
14) Do not pass flow_rule object for rule removal, cookie is sufficient
to achieve this.
15) Release flow_rule object in case of error from the offload commit
path.
16) Undo offload ruleset updates if transaction fails.
17) Check for error when binding flowtable callbacks, from wenxu.
18) Always unbind flowtable callbacks when unregistering hooks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_flow_rule_route_ipv6() and use it from the IPv6 and the inet
flowtable type definitions. Rename the nf_flow_rule_route() function to
nf_flow_rule_route_ipv4().
Adjust maximum number of actions, which now becomes 16 to leave
sufficient room for the IPv6 address mangling for NAT.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ism module is unloaded return control from exit routine only,
if all link groups are freed.
If an IB device is thrown away return control from device removal only,
if all link groups belonging to this device are freed.
A counters for the total number of SMCD link groups per ISM device is
introduced. ism module unloading continues only if the total number of
SMCD link groups for all ISM devices is zero. ISM device
removal continues only it the total number of SMCD link groups per ISM
device has decreased to zero.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 'module' member in the 'struct vsock_transport'
in order to get/put the transport module. This prevents the
module unloading while sockets are assigned to it.
We increase the module refcnt when a socket is assigned to a
transport, and we decrease the module refcnt when the socket
is destructed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of multiple transports in the
VSOCK core.
With the multi-transports support, we can use vsock with nested VMs
(using also different hypervisors) loading both guest->host and
host->guest transports at the same time.
Major changes:
- vsock core module can be loaded regardless of the transports
- vsock_core_init() and vsock_core_exit() are renamed to
vsock_core_register() and vsock_core_unregister()
- vsock_core_register() has a feature parameter (H2G, G2H, DGRAM)
to identify which directions the transport can handle and if it's
support DGRAM (only vmci)
- each stream socket is assigned to a transport when the remote CID
is set (during the connect() or when we receive a connection request
on a listener socket).
The remote CID is used to decide which transport to use:
- remote CID <= VMADDR_CID_HOST will use guest->host transport;
- remote CID == local_cid (guest->host transport) will use guest->host
transport for loopback (host->guest transports don't support loopback);
- remote CID > VMADDR_CID_HOST will use host->guest transport;
- listener sockets are not bound to any transports since no transport
operations are done on it. In this way we can create a listener
socket, also if the transports are not loaded or with VMADDR_CID_ANY
to listen on all transports.
- DGRAM sockets are handled as before, since only the vmci_transport
provides this feature.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All transports call __vsock_create() with the same parameters,
most of them depending on the parent socket. In order to simplify
the VSOCK core APIs exposed to the transports, this patch adds
the vsock_create_connected() callable from transports to create
a new socket when a connection request is received.
We also unexported the __vsock_create().
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_transport and vmci_transport handle the buffer_size
sockopts in a very similar way.
In order to support multiple transports, this patch moves this
handling in the core to allow the user to change the options
also if the socket is not yet assigned to any transport.
This patch also adds the '.notify_buffer_size' callback in the
'struct virtio_transport' in order to inform the transport,
when the buffer_size is changed by the user. It is also useful
to limit the 'buffer_size' requested (e.g. virtio transports).
Acked-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now the 'struct vsock_sock' object contains a pointer to
the transport, this patch adds a parameter to the
vsock_core_get_transport() to return the right transport
assigned to the socket.
This patch modifies also the virtio_transport_get_ops(), that
uses the vsock_core_get_transport(), adding the
'struct vsock_sock *' parameter.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to support multiple transports, this patch adds
the 'transport' member at the 'struct vsock_sock'.
This new field is initialized during the creation in the
__vsock_create() function.
This patch also renames the global 'transport' pointer to
'transport_single', since for now we're only supporting a single
transport registered at run-time.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This header file now only includes the "uapi/linux/vm_sockets.h".
We can include directly it when needed.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-11-13
1) Remove a unnecessary net_exit function from the xfrm interface.
From Xin Long.
2) Assign xfrm4_udp_encap_rcv to a UDP socket only if xfrm
is configured. From Alexey Dobriyan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the dataplane hardware offload to the flowtable
infrastructure. Three new flags represent the hardware state of this
flow:
* FLOW_OFFLOAD_HW: This flow entry resides in the hardware.
* FLOW_OFFLOAD_HW_DYING: This flow entry has been scheduled to be remove
from hardware. This might be triggered by either packet path (via TCP
RST/FIN packet) or via aging.
* FLOW_OFFLOAD_HW_DEAD: This flow entry has been already removed from
the hardware, the software garbage collector can remove it from the
software flowtable.
This patch supports for:
* IPv4 only.
* Aging via FLOW_CLS_STATS, no packet and byte counter synchronization
at this stage.
This patch also adds the action callback that specifies how to convert
the flow entry into the flow_rule object that is passed to the driver.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the NFTA_FLOWTABLE_FLAGS attribute that allows users to
specify the NF_FLOWTABLE_HW_OFFLOAD flag. This patch also adds a new
setup interface for the flowtable type to perform the flowtable offload
block callback configuration.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the infrastructure to support for flow entry types.
The initial type is NF_FLOW_OFFLOAD_ROUTE that stores the routing
information into the flow entry to define a fastpath for the classic
forwarding path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move rcu_head to struct flow_offload, then remove the flow_offload_entry
structure definition.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not have access to the flow_offload structure, hence remove
this union from this flow_offload object as well as the original comment
on top of it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this code by storing the pointer to conntrack object in the
flow_offload structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
after commit 4097e9d250 ("net: sched: don't use tc_action->order during
action dump"), 'act->order' is initialized but then it's no more read, so
we can just remove this member of struct tc_action.
CC: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink supports pair output of name and value. When the value is
binary, it must be presented in an array. If the length of the binary
value exceeds fmsg limitation, break the value into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netprio uses cgroup ID to index the priority mapping table. This is
currently okay as cgroup IDs are allocated using idr and packed.
However, cgroup IDs will be changed to use full 64bit range and won't
be packed making this impractical. netprio doesn't care what type of
IDs it uses as long as they can identify the controller instances and
are packed. Let's switch to css IDs instead of cgroup IDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Namhyung Kim <namhyung@kernel.org>
New device parameter to enable/disable handling of RoCE traffic in the
device.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new feature defined in section 5 of rfc7829: "Primary Path
Switchover". By introducing a new tunable parameter:
Primary.Switchover.Max.Retrans (PSMR)
The primary path will be changed to another active path when the path
error counter on the old primary path exceeds PSMR, so that "the SCTP
sender is allowed to continue data transmission on a new working path
even when the old primary destination address becomes active again".
This patch is to add this tunable parameter, 'ps_retrans' per netns,
sock, asoc and transport. It also allows a user to change ps_retrans
per netns by sysctl, and ps_retrans per sock/asoc/transport will be
initialized with it.
The check will be done in sctp_do_8_2_transport_strike() when this
feature is enabled.
Note this feature is disabled by initializing 'ps_retrans' per netns
as 0xffff by default, and its value can't be less than 'pf_retrans'
when changing by sysctl.
v3->v4:
- add define SCTP_PS_RETRANS_MAX 0xffff, and use it on extra2 of
sysctl 'ps_retrans'.
- add a new entry for ps_retrans on ip-sysctl.txt.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in rfc7829, section 3, point 12:
The SCTP stack SHOULD expose the PF state of its destination
addresses to the ULP as well as provide the means to notify the
ULP of state transitions of its destination addresses from
active to PF, and vice versa. However, it is recommended that
an SCTP stack implementing SCTP-PF also allows for the ULP to be
kept ignorant of the PF state of its destinations and the
associated state transitions, thus allowing for retention of the
simpler state transition model of [RFC4960] in the ULP.
Not only does it allow to expose the PF state to ULP, but also
allow to ignore sctp-pf to ULP.
So this patch is to add pf_expose per netns, sock and asoc. And in
sctp_assoc_control_transport(), ulp_notify will be set to false if
asoc->expose is not 'enabled' in next patch.
It also allows a user to change pf_expose per netns by sysctl, and
pf_expose per sock and asoc will be initialized with it.
Note that pf_expose also works for SCTP_GET_PEER_ADDR_INFO sockopt,
to not allow a user to query the state of a sctp-pf peer address
when pf_expose is 'disabled', as said in section 7.3.
v1->v2:
- Fix a build warning noticed by Nathan Chancellor.
v2->v3:
- set pf_expose to UNUSED by default to keep compatible with old
applications.
v3->v4:
- add a new entry for pf_expose on ip-sysctl.txt, as Marcelo suggested.
- change this patch to 1/5, and move sctp_assoc_control_transport
change into 2/5, as Marcelo suggested.
- use SCTP_PF_EXPOSE_UNSET instead of SCTP_PF_EXPOSE_UNUSED, and
set SCTP_PF_EXPOSE_UNSET to 0 in enum, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To implement airtime queue limiting, we need to keep a running account of
the estimated airtime of all skbs queued into the device. Do to this
correctly, we need to store the airtime estimate into the skb so we can
decrease the outstanding balance when the skb is freed. This means that the
time estimate must be stored somewhere that will survive for the lifetime
of the skb.
To get this, decrease the size of the ack_frame_id field to 6 bits, and
lower the size of the ID space accordingly. This leaves 10 bits for use for
tx_time_est, which is enough to store a maximum of 4096 us, if we shift the
values so they become units of 4us.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/157182474063.150713.16132669599100802716.stgit@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.
To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.
Fixes: 557fc4a098 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add layer 3 generic packet exception traps that can report trapped
packets and documentation of the traps.
Unlike drop traps, these exception traps also need to inject the packet
to the kernel's receive path. For example, a packet that was trapped due
to unreachable neighbour need to be injected into the kernel so that it
will trigger an ARP request or a neighbour solicitation message.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during layer
3 forwarding.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_make_synack() already uses tcp_clock_ns(), and can pass
the value to cookie_init_timestamp() to avoid another call
to ktime_get_ns() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing register size validation in bitwise and cmp offloads.
2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
from Dan Carpenter.
3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
Stefano Brivio.
4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
from Jozsef Kadlecsik.
5) Fix unaligned access to private data area of nf_tables instructions,
from Lukas Wunner.
6) Relax check for object updates, reported as a regression by
Eric Garver, patch from Fernando Fernandez Mancera.
7) Crash on ebtables dnat extension when used from the output path.
From Florian Westphal.
8) Fix bogus EOPNOTSUPP when updating basechain flags.
9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.
TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.
This has two problems:
- writers don't wake other threads up when they leave the kernel;
meaning that this scheme works for single extra thread (second
application thread or delayed work) because memory becoming
available will send a wake up request, but as Mallesham and
Pooja report with larger number of threads it leads to threads
being put to sleep indefinitely;
- the delayed work does not get _scheduled_ but it may _run_ when
other writers are present leading to crashes as writers don't
expect state to change under their feet (same records get pushed
and freed multiple times); it's hard to reliably bail from the
work, however, because the mere presence of a writer does not
guarantee that the writer will push pending records before exiting.
Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.
The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Mallesham Jatharakonda <mallesh537@gmail.com>
Reported-by: Pooja Trivedi <poojatrivedi@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_max_ack_backlog can be read without any lock being held
at least in TCP/DCCP cases.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common instances of the following construct :
if (n->confirmed != now)
n->confirmed = now;
A C compiler could legally remove the conditional.
Use READ_ONCE()/WRITE_ONCE() to avoid this problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of READ_ONCE() and WRITE_ONCE() to prevent
load-tearing and store-tearing in sock_read_timestamp()
and sock_write_timestamp()
This might prevent another KCSAN report.
Fixes: 3a0ed3e961 ("sock: Make sock->sk_stamp thread-safe")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gnet_stats_basic_packed was really meant to be private kernel structure.
If this proves to be a problem, we will have to rename the in-kernel
version.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes: 8b64678e0a ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since de77ecd4ef ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoking the following commands on a 32-bit architecture with strict
alignment requirements (such as an ARMv7-based Raspberry Pi) results
in an alignment exception:
# nft add table ip test-ip4
# nft add chain ip test-ip4 output { type filter hook output priority 0; }
# nft add rule ip test-ip4 output quota 1025 bytes
Alignment trap: not handling instruction e1b26f9f at [<7f4473f8>]
Unhandled fault: alignment exception (0x001) at 0xb832e824
Internal error: : 1 [#1] PREEMPT SMP ARM
Hardware name: BCM2835
[<7f4473fc>] (nft_quota_do_init [nft_quota])
[<7f447448>] (nft_quota_init [nft_quota])
[<7f4260d0>] (nf_tables_newrule [nf_tables])
[<7f4168dc>] (nfnetlink_rcv_batch [nfnetlink])
[<7f416bd0>] (nfnetlink_rcv [nfnetlink])
[<8078b334>] (netlink_unicast)
[<8078b664>] (netlink_sendmsg)
[<8071b47c>] (sock_sendmsg)
[<8071bd18>] (___sys_sendmsg)
[<8071ce3c>] (__sys_sendmsg)
[<8071ce94>] (sys_sendmsg)
The reason is that nft_quota_do_init() calls atomic64_set() on an
atomic64_t which is only aligned to 32-bit, not 64-bit, because it
succeeds struct nft_expr in memory which only contains a 32-bit pointer.
Fix by aligning the nft_expr private data to 64-bit.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-11-02
The following pull-request contains BPF updates for your *net-next* tree.
We've added 30 non-merge commits during the last 7 day(s) which contain
a total of 41 files changed, 1864 insertions(+), 474 deletions(-).
The main changes are:
1) Fix long standing user vs kernel access issue by introducing
bpf_probe_read_user() and bpf_probe_read_kernel() helpers, from Daniel.
2) Accelerated xskmap lookup, from Björn and Maciej.
3) Support for automatic map pinning in libbpf, from Toke.
4) Cleanup of BTF-enabled raw tracepoints, from Alexei.
5) Various fixes to libbpf and selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit the XSKMAP entry lookup function used by the XDP
redirect code is moved from the xskmap.c file to the xdp_sock.h
header, so the lookup can be inlined from, e.g., the
bpf_xdp_redirect_map() function.
Further the __xsk_map_redirect() and __xsk_map_flush() is moved to the
xsk.c, which lets the compiler inline the xsk_rcv() and xsk_flush()
functions.
Finally, all the XDP socket functions were moved from linux/bpf.h to
net/xdp_sock.h, where most of the XDP sockets functions are anyway.
This yields a ~2% performance boost for the xdpsock "rx_drop"
scenario.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191101110346.15004-4-bjorn.topel@gmail.com
Now that the DSA ports are listed in the switch fabric, there is
no need to store the dsa_switch structures from the drivers in the
fabric anymore. So get rid of the dst->ds static array.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not use the ds->rtable static arrays anymore, get rid of it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct tc_action with new "tcfa_flags" field. Set the field in
tcf_idr_create() function and provide new helper
tcf_idr_create_from_flags() that derives 'cpustats' boolean from flags
value. Update individual hardware-offloaded actions init() to pass their
"flags" argument to new helper in order to skip percpu stats allocation
when user requested it through flags.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend TCA_ACT space with nla_bitfield32 flags. Add
TCA_ACT_FLAGS_NO_PERCPU_STATS as the only allowed flag. Parse the flags in
tcf_action_init_1() and pass resulting value as additional argument to
a_o->init().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify stats update helper functions introduced in previous patches in this
series to fallback to regular tc_action->tcfa_{b|q}stats if cpu stats are
not allocated for the action argument. If regular non-percpu allocated
counters are in use, then obtain action tcfa_lock while modifying them.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit introduced helper function for updating qstats and
refactored set of actions to use the helpers, instead of modifying qstats
directly. However, one of the affected action exposes its qstats to
skb_tc_reinsert(), which then modifies it.
Refactor skb_tc_reinsert() to return integer error code and don't increment
overlimit qstats in case of error, and use the returned error code in
tcf_mirred_act() to manually increment the overlimit counter with new
helper function.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_qstats counters into standalone act
API functions. Change hardware offloaded actions that use percpu counter
allocation to use the new functions instead of accessing cpu_qstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract common code that increments cpu_bstats counter into standalone act
API function. Change hardware offloaded actions that use percpu counter
allocation to use the new function instead of incrementing cpu_bstats
directly.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all implementations of tc_action_ops->stats_update() callback
have almost exactly the same implementation of counters update
code (besides gact which also updates drop counter). In order to simplify
support for using both percpu-allocated and regular action counters
depending on run-time flag in following patches, extract action counters
update code into standalone function in act API.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICMP flow dissector currently parses only the Type and Code fields.
Some ICMP packets (echo, timestamp) have a 16 bit Identifier field which
is used to correlate packets.
Add such field in flow_dissector_key_icmp and replace skb_flow_get_be16()
with a more complex function which populate this field.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documents two piece of code which can't be understood at a glance.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only smc-related reference in net/sock.h is struct smc_hashinfo.
But just its address is refered to. Thus there is no need for the
include of net/smc.h. Remove it.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return directly from within the loop as soon as the port is found,
otherwise we won't return NULL if the end of the list is reached.
Fixes: b96ddf254b ("net: dsa: use ports list in dsa_to_port")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_page_frag() optimizes skb_frag allocations by using per-task
skb_frag cache when it knows it's the only user. The condition is
determined by seeing whether the socket allocation mask allows
blocking - if the allocation may block, it obviously owns the task's
context and ergo exclusively owns current->task_frag.
Unfortunately, this misses recursion through memory reclaim path.
Please take a look at the following backtrace.
[2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10
...
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
sock_xmit.isra.24+0xa1/0x170 [nbd]
nbd_send_cmd+0x1d2/0x690 [nbd]
nbd_queue_rq+0x1b5/0x3b0 [nbd]
__blk_mq_try_issue_directly+0x108/0x1b0
blk_mq_request_issue_directly+0xbd/0xe0
blk_mq_try_issue_list_directly+0x41/0xb0
blk_mq_sched_insert_requests+0xa2/0xe0
blk_mq_flush_plug_list+0x205/0x2a0
blk_flush_plug_list+0xc3/0xf0
[1] blk_finish_plug+0x21/0x2e
_xfs_buf_ioapply+0x313/0x460
__xfs_buf_submit+0x67/0x220
xfs_buf_read_map+0x113/0x1a0
xfs_trans_read_buf_map+0xbf/0x330
xfs_btree_read_buf_block.constprop.42+0x95/0xd0
xfs_btree_lookup_get_block+0x95/0x170
xfs_btree_lookup+0xcc/0x470
xfs_bmap_del_extent_real+0x254/0x9a0
__xfs_bunmapi+0x45c/0xab0
xfs_bunmapi+0x15/0x30
xfs_itruncate_extents_flags+0xca/0x250
xfs_free_eofblocks+0x181/0x1e0
xfs_fs_destroy_inode+0xa8/0x1b0
destroy_inode+0x38/0x70
dispose_list+0x35/0x50
prune_icache_sb+0x52/0x70
super_cache_scan+0x120/0x1a0
do_shrink_slab+0x120/0x290
shrink_slab+0x216/0x2b0
shrink_node+0x1b6/0x4a0
do_try_to_free_pages+0xc6/0x370
try_to_free_mem_cgroup_pages+0xe3/0x1e0
try_charge+0x29e/0x790
mem_cgroup_charge_skmem+0x6a/0x100
__sk_mem_raise_allocated+0x18e/0x390
__sk_mem_schedule+0x2a/0x40
[0] tcp_sendmsg_locked+0x8eb/0xe10
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x26d/0x2b0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In [0], tcp_send_msg_locked() was using current->page_frag when it
called sk_wmem_schedule(). It already calculated how many bytes can
be fit into current->page_frag. Due to memory pressure,
sk_wmem_schedule() called into memory reclaim path which called into
xfs and then IO issue path. Because the filesystem in question is
backed by nbd, the control goes back into the tcp layer - back into
tcp_sendmsg_locked().
nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes
sense - it's in the process of freeing memory and wants to be able to,
e.g., drop clean pages to make forward progress. However, this
confused sk_page_frag() called from [2]. Because it only tests
whether the allocation allows blocking which it does, it now thinks
current->page_frag can be used again although it already was being
used in [0].
After [2] used current->page_frag, the offset would be increased by
the used amount. When the control returns to [0],
current->page_frag's offset is increased and the previously calculated
number of bytes now may overrun the end of allocated memory leading to
silent memory corruptions.
Fix it by adding gfpflags_normal_context() which tests sleepable &&
!reclaim and use it to determine whether to use current->task_frag.
v2: Eric didn't like gfp flags being tested twice. Introduce a new
helper gfpflags_normal_context() and combine the two tests.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix crash on flowtable due to race between garbage collection
and insertion.
2) Restore callback unbinding in netfilter offloads.
3) Fix races on IPVS module removal, from Davide Caratti.
4) Make old_secure_tcp per-netns to fix sysbot report,
from Eric Dumazet.
5) Validate matching length in netfilter offloads, from wenxu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
more specifically:
* Updates for ipset:
1) Coding style fix for ipset comment extension, from Jeremy Sowden.
2) De-inline many functions in ipset, from Jeremy Sowden.
3) Move ipset function definition from header to source file.
4) Move ip_set_put_flags() to source, export it as a symbol, remove
inline.
5) Move range_to_mask() to the source file where this is used.
6) Move ip_set_get_ip_port() to the source file where this is used.
* IPVS selftests and netns improvements:
7) Two patches to speedup ipvs netns dismantle, from Haishuang Yan.
8) Three patches to add selftest script for ipvs, also from
Haishuang Yan.
* Conntrack updates and new nf_hook_slow_list() function:
9) Document ct ecache extension, from Florian Westphal.
10) Skip ct extensions from ctnetlink dump, from Florian.
11) Free ct extension immediately, from Florian.
12) Skip access to ecache extension from nf_ct_deliver_cached_events()
this is not correct as reported by Syzbot.
13) Add and use nf_hook_slow_list(), from Florian.
* Flowtable infrastructure updates:
14) Move priority to nf_flowtable definition.
15) Dynamic allocation of per-device hooks in flowtables.
16) Allow to include netdevice only once in flowtable definitions.
17) Rise maximum number of devices per flowtable.
* Netfilter hardware offload infrastructure updates:
18) Add nft_flow_block_chain() helper function.
19) Pass callback list to nft_setup_cb_call().
20) Add nft_flow_cls_offload_setup() helper function.
21) Remove rules for the unregistered device via netdevice event.
22) Support for multiple devices in a basechain definition at the
ingress hook.
22) Add nft_chain_offload_cmd() helper function.
23) Add nft_flow_block_offload_init() helper function.
24) Rewind in case of failing to bind multiple devices to hook.
25) Typo in IPv6 tproxy module description, from Norman Rasmussen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_HWBM is not set, then these stub functions in
<net/hwbm.h> should be declared static to avoid trying to
export them from any driver that includes this.
Fixes the following sparse warnings:
./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static?
./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static?
./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All bonding device has same lockdep key and subclass is initialized with
nest_level.
But actual nest_level value can be changed when a lower device is attached.
And at this moment, the subclass should be updated but it seems to be
unsafe.
So this patch makes bonding use dynamic lockdep key instead of the
subclass.
Test commands:
ip link add bond0 type bond
for i in {1..5}
do
let A=$i-1
ip link add bond$i type bond
ip link set bond$i master bond$A
done
ip link set bond5 master bond0
Splat looks like:
[ 307.992912] WARNING: possible recursive locking detected
[ 307.993656] 5.4.0-rc3+ #96 Tainted: G W
[ 307.994367] --------------------------------------------
[ 307.995092] ip/761 is trying to acquire lock:
[ 307.995710] ffff8880513aac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.997045]
but task is already holding lock:
[ 307.997923] ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.999215]
other info that might help us debug this:
[ 308.000251] Possible unsafe locking scenario:
[ 308.001137] CPU0
[ 308.001533] ----
[ 308.001915] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.002609] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.003302]
*** DEADLOCK ***
[ 308.004310] May be due to missing lock nesting notation
[ 308.005319] 3 locks held by ip/761:
[ 308.005830] #0: ffffffff9fcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[ 308.006894] #1: ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 308.008243] #2: ffffffff9f9219c0 (rcu_read_lock){....}, at: bond_get_stats+0x9f/0x500 [bonding]
[ 308.009422]
stack backtrace:
[ 308.010124] CPU: 0 PID: 761 Comm: ip Tainted: G W 5.4.0-rc3+ #96
[ 308.011097] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 308.012179] Call Trace:
[ 308.012601] dump_stack+0x7c/0xbb
[ 308.013089] __lock_acquire+0x269d/0x3de0
[ 308.013669] ? register_lock_class+0x14d0/0x14d0
[ 308.014318] lock_acquire+0x164/0x3b0
[ 308.014858] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.015520] _raw_spin_lock_nested+0x2e/0x60
[ 308.016129] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.017215] bond_get_stats+0xb8/0x500 [bonding]
[ 308.018454] ? bond_arp_rcv+0xf10/0xf10 [bonding]
[ 308.019710] ? rcu_read_lock_held+0x90/0xa0
[ 308.020605] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 308.021286] ? bond_get_stats+0x9f/0x500 [bonding]
[ 308.021953] dev_get_stats+0x1ec/0x270
[ 308.022508] bond_get_stats+0x1d1/0x500 [bonding]
Fixes: d3fff6c443 ("net: add netdev_lockdep_set_classes() helper")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported the following issue :
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e16 ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
UDP IPv6 packets auto flowlabels are using a 32bit secret
(static u32 hashrnd in net/core/flow_dissector.c) and
apply jhash() over fields known by the receivers.
Attackers can easily infer the 32bit secret and use this information
to identify a device and/or user, since this 32bit secret is only
set at boot time.
Really, using jhash() to generate cookies sent on the wire
is a serious security concern.
Trying to change the rol32(hash, 16) in ip6_make_flowlabel() would be
a dead end. Trying to periodically change the secret (like in sch_sfq.c)
could change paths taken in the network for long lived flows.
Let's switch to siphash, as we did in commit df453700e8
("inet: switch IP ID generator to siphash")
Using a cryptographically strong pseudo random function will solve this
privacy issue and more generally remove other weak points in the stack.
Packet schedulers using skb_get_hash_perturb() benefit from this change.
Fixes: b56774163f ("ipv6: Enable auto flow labels by default")
Fixes: 42240901f7 ("ipv6: Implement different admin modes for automatic flow labels")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Fixes: cb1ce2ef38 ("ipv6: Implement automatic flow label generation on transmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Berger <jonathann1@walla.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to register one netdev basechain to multiple
devices. This adds a new NFTA_HOOK_DEVS netlink attribute to specify
the list of netdevices. Basechains store a list of hooks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Rise the maximum limit of devices per flowtable up to 256. Rename
NFT_FLOWTABLE_DEVICE_MAX to NFT_NETDEVICE_MAX in preparation to reuse
the netdev hook parser for ingress basechain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Hardware offload needs access to the priority field, store this field in
the nf_flowtable object.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.
Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.
At the same time, provide a better error message for CPU-less tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the switches and their ports.
At the same time, provide setup states and messages for ports and
switches as it is done for the trees.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of accessing the dsa_switch array
of ports in the dsa_to_port helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.
In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel test robot reported a ~7% regression on TCP_CRR tests
that they bisected to the cited commit.
Indeed, every time a new TCP socket is created or deleted,
the atomic counter net->count is touched (via get_net(net)
and put_net(net) calls)
So cpus might have to reload a contended cache line in
net_hash_mix(net) calls.
We need to reorder 'struct net' fields to move @hash_mix
in a read mostly cache line.
We move in the first cache line fields that can be
dirtied often.
We probably will have to address in a followup patch
the __randomize_layout that was added in linux-4.13,
since this might break our placement choices.
Fixes: 355b985537 ("netns: provide pure entropy for net_hash_mix()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of waiting for rcu grace period just free it directly.
This is safe because conntrack lookup doesn't consider extensions.
Other accesses happen while ct->ext can't be free'd, either because
a ct refcount was taken or because the conntrack hash bucket lock or
the dying list spinlock have been taken.
This allows to remove __krealloc in a followup patch, netfilter was the
only user.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
-----BEGIN PGP SIGNATURE-----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=IJ7D
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more small things, nothing really stands out:
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_wmem_queued while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
sk_wmem_queued_add() helper is added so that we can in
the future convert to ADD_ONCE() or equivalent if/when
available.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_sndbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of tcp_poll(), there are few places where we fetch
sk->sk_rcvbuf while this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make sure write
sides use corresponding WRITE_ONCE() to avoid store-tearing.
Note that other transports probably need similar fixes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->snd_nxt while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where we fetch tp->write_seq while
this field can change from IRQ or other cpu.
We need to add READ_ONCE() annotations, and also make
sure write sides use corresponding WRITE_ONCE() to avoid
store-tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sock_rcvlowat() or int_sk_rcvlowat() might be called without the socket
lock for example from tcp_poll().
Use READ_ONCE() to document the fact that other cpus might change
sk->sk_rcvlowat under us and avoid KCSAN splats.
Use WRITE_ONCE() on write sides too.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
tcp_memory_pressure is read without holding any lock,
and its value could be changed on other cpus.
Use READ_ONCE() to annotate these lockless reads.
The write side is already using atomic ops.
Fixes: b8da51ebb1 ("tcp: introduce tcp_under_memory_pressure()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
reqsk_queue_empty() is called from inet_csk_listen_poll() while
other cpus might write ->rskq_accept_head value.
Use {READ|WRITE}_ONCE() to avoid compiler tricks
and potential KCSAN splats.
Fixes: fff1f3001c ("tcp: add a spinlock to protect struct request_sock_queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a "going_away" indication to ISM devices and IB ports and
avoid creation of new connections on such disappearing devices.
And do not handle ISM events if ISM device is disappearing.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch introduces separate locks for the split SMCD and SMCR
link group lists.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Currently SMCD and SMCR link groups are maintained in one list.
To facilitate abnormal termination handling they are split into
a separate list for SMCR link groups and separate lists for SMCD
link groups per SMCD device.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to add a new event SCTP_SEND_FAILED_EVENT described in
rfc6458#section-6.1.11. It's a update of SCTP_SEND_FAILED event:
struct sctp_sndrcvinfo ssf_info is replaced with
struct sctp_sndinfo ssfe_info in struct sctp_send_failed_event.
SCTP_SEND_FAILED is being deprecated, but we don't remove it in this
patch. Both are being processed in sctp_datamsg_destroy() when the
corresp event flag is set.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
A helper sctp_ulpevent_nofity_peer_addr_change() will be extracted
to make peer_addr_change event and enqueue it, and the helper will
be called in sctp_assoc_add_peer() to send SCTP_ADDR_ADDED event.
This event is described in rfc6458#section-6.1.2:
SCTP_ADDR_ADDED: The address is now part of the association.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to fix a NULL-ptr deref in selinux_socket_connect_helper:
[...] kasan: GPF could be caused by NULL-ptr deref or user memory access
[...] RIP: 0010:selinux_socket_connect_helper+0x94/0x460
[...] Call Trace:
[...] selinux_sctp_bind_connect+0x16a/0x1d0
[...] security_sctp_bind_connect+0x58/0x90
[...] sctp_process_asconf+0xa52/0xfd0 [sctp]
[...] sctp_sf_do_asconf+0x785/0x980 [sctp]
[...] sctp_do_sm+0x175/0x5a0 [sctp]
[...] sctp_assoc_bh_rcv+0x285/0x5b0 [sctp]
[...] sctp_backlog_rcv+0x482/0x910 [sctp]
[...] __release_sock+0x11e/0x310
[...] release_sock+0x4f/0x180
[...] sctp_accept+0x3f9/0x5a0 [sctp]
[...] inet_accept+0xe7/0x720
It was caused by that the 'newsk' sk_socket was not set before going to
security sctp hook when processing asconf chunk with SCTP_PARAM_ADD_IP
or SCTP_PARAM_SET_PRIMARY:
inet_accept()->
sctp_accept():
lock_sock():
lock listening 'sk'
do_softirq():
sctp_rcv(): <-- [1]
asconf chunk arrives and
enqueued in 'sk' backlog
sctp_sock_migrate():
set asoc's sk to 'newsk'
release_sock():
sctp_backlog_rcv():
lock 'newsk'
sctp_process_asconf() <-- [2]
unlock 'newsk'
sock_graft():
set sk_socket <-- [3]
As it shows, at [1] the asconf chunk would be put into the listening 'sk'
backlog, as accept() was holding its sock lock. Then at [2] asconf would
get processed with 'newsk' as asoc's sk had been set to 'newsk'. However,
'newsk' sk_socket is not set until [3], while selinux_sctp_bind_connect()
would deref it, then kernel crashed.
Here to fix it by adding the chunk to sk_backlog until newsk sk_socket is
set when .accept() is done.
Note that sk->sk_socket can be NULL when the sock is closed, so SOCK_DEAD
flag is also needed to check in sctp_newsk_ready().
Thanks to Ondrej for reviewing the code.
Fixes: d452930fd3 ("selinux: Add SCTP support")
Reported-by: Ying Xu <yinxu@redhat.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If IPsec is not configured, there is no reason to delay the inevitable.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
* allow scanning when operating on radar channels in
ETSI regdomains
* accept deauth frames in IBSS - we have code to parse
and handle them, but were dropping them early
* fix an allocation failure path in hwsim
* fix a failure path memory leak in nl80211 FTM code
* fix RCU handling & locking in multi-BSSID parsing
* reject malformed SSID in mac80211 (this shouldn't
really be able to happen, but defense in depth)
* avoid userspace buffer overrun in ancient wext code
if SSID was too long
-----BEGIN PGP SIGNATURE-----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=k685
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A number of fixes:
* allow scanning when operating on radar channels in
ETSI regdomains
* accept deauth frames in IBSS - we have code to parse
and handle them, but were dropping them early
* fix an allocation failure path in hwsim
* fix a failure path memory leak in nl80211 FTM code
* fix RCU handling & locking in multi-BSSID parsing
* reject malformed SSID in mac80211 (this shouldn't
really be able to happen, but defense in depth)
* avoid userspace buffer overrun in ancient wext code
if SSID was too long
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a single bit instead of boolean to remember if packet
was already decrypted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store async_capable on a single bit instead of a full integer
to save space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary pointer chasing and calculations, callers already
have most of the state tls_device_decrypted() needs.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genl_family_attrbuf() function is no longer used by anyone, so remove it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the dumpit info struct for attrs. Instead of existing attribute
validation do parse them and save in the info struct. Caller can benefit
from this and does not have to do parse itself. In order to properly
free attrs, genl_family pointer needs to be added to dumpit info struct
as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the cb->data is taken by ops during non-parallel dumping.
Introduce a new structure genl_dumpit_info and store the ops there.
Distribute the info to both non-parallel and parallel dumping. Also add
a helper genl_dumpit_info() to easily get the info structure in the
dumpit callback from cb.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newly allocated devlink instance allow drivers to set net struct
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a skeleton structure for adding TLS statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracing of device-related interaction to aid performance
analysis, especially around resync:
tls:tls_device_offload_set
tls:tls_device_rx_resync_send
tls:tls_device_rx_resync_nh_schedule
tls:tls_device_rx_resync_nh_delay
tls:tls_device_tx_resync_req
tls:tls_device_tx_resync_send
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tls_hw_* functions are quite confusingly named, since they
are related to the TOE-offload, not TLS_HW offload which doesn't
require TOE. Rename them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tls_hw_* functions to a new, separate source file
to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename struct tls_device to struct tls_toe_device to avoid
confusion with normal, non-TOE offload.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tls_device structure and register/unregister functions
to a new header to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to get net struct for devlink instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike events for registered notifier, during the registration, the
errors that happened for the block being registered are not propagated
up to the caller. Make sure the error is propagated for FIB rules and
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The struct __dsa_skb_cb is supposed to span the entire 48-byte skb
control block, while the struct dsa_skb_cb only the portion of it which
is used by the DSA core (the rest is available as private data to
drivers).
The DSA_SKB_CB and __DSA_SKB_CB helpers are supposed to help retrieve
this pointer based on a skb, but it turns out there is nobody directly
interested in the struct __dsa_skb_cb in the kernel. So remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Often the code for example in drivers is interested in getting notifier
call only from certain network namespace. In addition to the existing
global netdevice notifier chain introduce per-netns chains and allow
users to register to that. Eventually this would eliminate unnecessary
overhead in case there are many netdevices in many network namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push iterations over net namespaces and netdevices from
register_netdevice_notifier() and unregister_netdevice_notifier()
into helper functions. Along with that introduce continue_reverse macros
to make the code a bit nicer allowing to get rid of "last" marks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_twsk_unique() has a hard coded assumption about ipv4 loopback
being 127/8
Lets instead use the standard ipv4_is_loopback() method,
in a new ipv6_addr_v4mapped_loopback() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Add NFT_CHAIN_POLICY_UNSET to replace hardcoded -1 to
specify that the chain policy is unset. The chain policy
field is actually defined as an 8-bit unsigned integer.
2) Remove always true condition reported by smatch in
chain policy check.
3) Fix element lookup on dynamic sets, from Florian Westphal.
4) Use __u8 in ebtables uapi header, from Masahiro Yamada.
5) Bogus EBUSY when removing flowtable after chain flush,
from Laura Garcia Liebana.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ctl packets sent on behalf of TIME_WAIT sockets currently
have a zero skb->priority, which can cause various problems.
In this patch we :
- add a tw_priority field in struct inet_timewait_sock.
- populate it from sk->sk_priority when a TIME_WAIT is created.
- For IPv4, change ip_send_unicast_reply() and its two
callers to propagate tw_priority correctly.
ip_send_unicast_reply() no longer changes sk->sk_priority.
- For IPv6, make sure TIME_WAIT sockets pass their tw_priority
field to tcp_v6_send_response() and tcp_v6_send_ack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ip6_xmit() sets skb->priority based on sk->sk_priority
This is not desirable for TCP since TCP shares the same ctl socket
for a given netns. We want to be able to send RST or ACK packets
with a non zero skb->priority.
This patch has no functional change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The deletion of a flowtable after a flush in the same transaction
results in EBUSY. This patch adds an activation and deactivation of
flowtables in order to update the _use_ counter.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Julian noted that rt_uses_gateway has a more subtle use than 'is gateway
set':
https://lore.kernel.org/netdev/alpine.LFD.2.21.1909151104060.2546@ja.home.ssi.bg/
Revert that part of the commit referenced in the Fixes tag.
Currently, there are no u8 holes in 'struct rtable'. There is a 4-byte hole
in the second cacheline which contains the gateway declaration. So move
rt_gw_family down to the gateway declarations since they are always used
together, and then re-use that u8 for rt_uses_gateway. End result is that
rtable size is unchanged.
Fixes: 1550c17193 ("ipv4: Prepare rtable for IPv6 gateway")
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Default policy is defined as a unsigned 8-bit field, do not use a
negative value to leave it unset, use this new NFT_CHAIN_POLICY_UNSET
instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Pull crypto updates from Herbert Xu:
"API:
- Add the ability to abort a skcipher walk.
Algorithms:
- Fix XTS to actually do the stealing.
- Add library helpers for AES and DES for single-block users.
- Add library helpers for SHA256.
- Add new DES key verification helper.
- Add surrounding bits for ESSIV generator.
- Add accelerations for aegis128.
- Add test vectors for lzo-rle.
Drivers:
- Add i.MX8MQ support to caam.
- Add gcm/ccm/cfb/ofb aes support in inside-secure.
- Add ofb/cfb aes support in media-tek.
- Add HiSilicon ZIP accelerator support.
Others:
- Fix potential race condition in padata.
- Use unbound workqueues in padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (311 commits)
crypto: caam - Cast to long first before pointer conversion
crypto: ccree - enable CTS support in AES-XTS
crypto: inside-secure - Probe transform record cache RAM sizes
crypto: inside-secure - Base RD fetchcount on actual RD FIFO size
crypto: inside-secure - Base CD fetchcount on actual CD FIFO size
crypto: inside-secure - Enable extended algorithms on newer HW
crypto: inside-secure: Corrected configuration of EIP96_TOKEN_CTRL
crypto: inside-secure - Add EIP97/EIP197 and endianness detection
padata: remove cpu_index from the parallel_queue
padata: unbind parallel jobs from specific CPUs
padata: use separate workqueues for parallel and serial work
padata, pcrypt: take CPU hotplug lock internally in padata_alloc_possible
crypto: pcrypt - remove padata cpumask notifier
padata: make padata_do_parallel find alternate callback CPU
workqueue: require CPU hotplug read exclusion for apply_workqueue_attrs
workqueue: unconfine alloc/apply/free_workqueue_attrs()
padata: allocate workqueue internally
arm64: dts: imx8mq: Add CAAM node
random: Use wait_event_freezable() in add_hwgenerator_randomness()
crypto: ux500 - Fix COMPILE_TEST warnings
...
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows taprio to offload the schedule enforcement to capable
network cards, resulting in more precise windows and less CPU usage.
The gate mask acts on traffic classes (groups of queues of same
priority), as specified in IEEE 802.1Q-2018, and following the existing
taprio and mqprio semantics.
It is up to the driver to perform conversion between tc and individual
netdev queues if for some reason it needs to make that distinction.
Full offload is requested from the network interface by specifying
"flags 2" in the tc qdisc creation command, which in turn corresponds to
the TCA_TAPRIO_ATTR_FLAG_FULL_OFFLOAD bit.
The important detail here is the clockid which is implicitly /dev/ptpN
for full offload, and hence not configurable.
A reference counting API is added to support the use case where Ethernet
drivers need to keep the taprio offload structure locally (i.e. they are
a multi-port switch driver, and configuring a port depends on the
settings of other ports as well). The refcount_t variable is kept in a
private structure (__tc_taprio_qopt_offload) and not exposed to drivers.
In the future, the private structure might also be expanded with a
backpointer to taprio_sched *q, to implement the notification system
described in the patch (of when admin became oper, or an error occurred,
etc, so the offload can be monitored with 'tc qdisc show').
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling in hardware intermediate representation tc_setup_flow_action()
directly obtains, checks and takes reference to dev used by mirred action,
instead of using act->ops->get_dev() API created specifically for this
purpose. In order to remove code duplication, refactor flow_action infra to
use action API when obtaining mirred action target dev. Extend get_dev()
with additional argument that is used to provide dev destructor to the
user.
Fixes: 5a6ff4b13d ("net: sched: take reference to action dev before calling offloads")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent patch set that removed rtnl lock dependency from cls hardware
offload API rtnl lock is only taken when reading action data and can be
released after action-specific data is parsed into intermediate
representation. However, sample action psample group is passed by pointer
without obtaining reference to it first, which makes it possible to
concurrently overwrite the action and deallocate object pointed by
psample_group pointer after rtnl lock is released but before driver
finished using the pointer.
To prevent such race condition, obtain reference to psample group while it
is used by flow_action infra. Extend psample API with function
psample_group_take() that increments psample group reference counter.
Extend struct tc_action_ops with new get_psample_group() API. Implement the
API for action sample using psample_group_take() and already existing
psample_group_put() as a destructor. Use it in tc_setup_flow_action() to
take reference to psample group pointed to by entry->sample.psample_group
and release it in tc_cleanup_flow_action().
Disable bh when taking psample_groups_lock. The lock is now taken while
holding action tcf_lock that is used by data path and requires bh to be
disabled, so doing the same for psample_groups_lock is necessary to
preserve SOFTIRQ-irq-safety.
Fixes: 918190f50e ("net: sched: flower: don't take rtnl lock for cls hw offloads API")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize flow_action_entry cleanup by extending the structure with
pointer to destructor function. Set the destructor in
tc_setup_flow_action(). Refactor tc_cleanup_flow_action() to call
entry->destructor() instead of using switch that dispatches by entry->id
and manually executes cleanup.
This refactoring is necessary for following patches in this series that
require destructor to use tc_action->ops callbacks that can't be easily
obtained in tc_cleanup_flow_action().
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP reuseport groups can hold a mix unconnected and connected sockets.
Ensure that connections only receive all traffic to their 4-tuple.
Fast reuseport returns on the first reuseport match on the assumption
that all matches are equal. Only if connections are present, return to
the previous behavior of scoring all sockets.
Record if connections are present and if so (1) treat such connected
sockets as an independent match from the group, (2) only return
2-tuple matches from reuseport and (3) do not return on the first
2-tuple reuseport match to allow for a higher scoring match later.
New field has_conns is set without locks. No other fields in the
bitmap are modified at runtime and the field is only ever set
unconditionally, so an RMW cannot miss a change.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Link: http://lkml.kernel.org/r/CA+FuTSfRP09aJNYRt04SS6qj22ViiOEWaWmLAwX0psk8-PGNxw@mail.gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test implemented by some_qdisc_is_busy() is somewhat loosy for
NOLOCK qdisc, as we may hit the following scenario:
CPU1 CPU2
// in net_tx_action()
clear_bit(__QDISC_STATE_SCHED...);
// in some_qdisc_is_busy()
val = (qdisc_is_running(q) ||
test_bit(__QDISC_STATE_SCHED,
&q->state));
// here val is 0 but...
qdisc_run(q)
// ... CPU1 is going to run the qdisc next
As a conseguence qdisc_run() in net_tx_action() can race with qdisc_reset()
in dev_qdisc_reset(). Such race is not possible for !NOLOCK qdisc as
both the above bit operations are under the root qdisc lock().
After commit 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
the race can cause use after free and/or null ptr dereference, but the root
cause is likely older.
This patch addresses the issue explicitly checking for deactivation under
the seqlock for NOLOCK qdisc, so that the qdisc_run() in the critical
scenario becomes a no-op.
Note that the enqueue() op can still execute concurrently with dev_qdisc_reset(),
but that is safe due to the skb_array() locking, and we can't avoid that
for NOLOCK qdiscs.
Fixes: 021a17ed79 ("pfifo_fast: drop unneeded additional lock on dequeue")
Reported-by: Li Shuang <shuali@redhat.com>
Reported-and-tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Fix error path of nf_tables_updobj(), from Dan Carpenter.
2) Move large structure away from stack in the nf_tables offload
infrastructure, from Arnd Bergmann.
3) Move indirect flow_block logic to nf_tables_offload.
4) Support for synproxy objects, from Fernando Fernandez Mancera.
5) Support for fwd and dup offload.
6) Add __nft_offload_get_chain() helper, this implicitly fixes missing
mutex and check for offload flags in the indirect block support,
patch from wenxu.
7) Remove rules on device unregistration, from wenxu. This includes
two preparation patches to reuse nft_flow_offload_chain() and
nft_flow_offload_rule().
Large batch from Jeremy Sowden to make a second pass to the
CONFIG_HEADER_TEST support and a bit of housekeeping:
8) Missing include guard in conntrack label header, from Jeremy Sowden.
9) A few coding style errors: trailing whitespace, incorrect indent in
Kconfig, and semicolons at the end of function definitions.
10) Remove unused ipt_init() and ip6t_init() declarations.
11) Inline xt_hashlimit, ebt_802_3 and xt_physdev headers. They are
only used once.
12) Update include directive in several netfilter files.
13) Remove unused include/net/netfilter/ipv6/nf_conntrack_icmpv6.h.
14) Move nf_ip6_ext_hdr() to include/linux/netfilter_ipv6.h
15) Move several synproxy structure definitions to nf_synproxy.h
16) Move nf_bridge_frag_data structure to include/linux/netfilter_bridge.h
17) Clean up static inline definitions in nf_conntrack_ecache.h.
18) Replace defined(CONFIG...) || defined(CONFIG...MODULE) with IS_ENABLED(CONFIG...).
19) Missing inline function conditional definitions based on Kconfig
preferences in synproxy and nf_conntrack_timeout.
20) Update br_nf_pre_routing_ipv6() definition.
21) Move conntrack code in linux/skbuff.h to nf_conntrack headers.
22) Several patches to remove superfluous CONFIG_NETFILTER and
CONFIG_NF_CONNTRACK checks in headers, coming from the initial batch
support for CONFIG_HEADER_TEST for netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Two inline functions defined in nf_conntrack_timestamp.h,
`nf_ct_tstamp_enabled` and `nf_ct_set_tstamp`, are not called anywhere.
Remove them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_zones.h was wrapped in a CONFIG_NF_CONNTRACK check in order
to fix compilation failures:
37ee3d5b3e ("netfilter: nf_defrag_ipv4: fix compilation error with NF_CONNTRACK=n")
Subsequent changes mean that these failures will no longer occur and the
check is unnecessary. Remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
`struct nf_hook_ops`, `struct nf_hook_state` and the `nf_hookfn`
function typedef appear in function and struct declarations and
definitions in a number of netfilter headers. The structs and typedef
themselves are defined by linux/netfilter.h but only when
CONFIG_NETFILTER is enabled. Define them unconditionally and add
forward declarations in order to remove CONFIG_NETFILTER conditionals
from the other headers.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is a superfluous `#if IS_ENABLED(CONFIG_NF_CONNTRACK)` check
wrapping some function declarations. Remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move some `struct nf_conntrack` code from linux/skbuff.h to
linux/nf_conntrack_common.h. Together with a couple of helpers for
getting and setting skb->_nfct, it allows us to remove
CONFIG_NF_CONNTRACK checks from net/netfilter/nf_conntrack.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The real br_nf_pre_routing_ipv6 function, defined when CONFIG_IPV6 is
enabled, expects `void *priv`, not `const struct nf_hook_ops *ops`.
Update the stub br_nf_pre_routing_ipv6, defined when CONFIG_IPV6 is
disabled, to match.
Fixes: 06198b34a3 ("netfilter: Pass priv instead of nf_hook_ops to netfilter hooks")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_synproxy.h contains three inline functions. The contents
of two of them are wrapped in CONFIG_NETFILTER_SYNPROXY checks and just
return NULL if it is not enabled. The third does nothing if they return
NULL, so wrap its contents as well.
nf_ct_timeout_data is only called if CONFIG_NETFILTER_TIMEOUT is
enabled. Wrap its contents in a CONFIG_NETFILTER_TIMEOUT check like the
other inline functions in nf_conntrack_timeout.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A few headers contain instances of:
#if defined(CONFIG_XXX) or defined(CONFIG_XXX_MODULE)
Replace them with:
#if IS_ENABLED(CONFIG_XXX)
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The header contains some inline functions defined as:
static inline f (...)
{
#ifdef CONFIG_NF_CONNTRACK_EVENTS
...
#else
...
#endif
}
and a few others as:
#ifdef CONFIG_NF_CONNTRACK_EVENTS
static inline f (...)
{
...
}
#else
static inline f (...)
{
...
}
#endif
Prefer the former style, which is more numerous.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is a struct definition function in nf_conntrack_bridge.h which is
not specific to conntrack and is used elswhere in netfilter. Move it
into netfilter_bridge.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There is some non-conntrack code in the nf_conntrack_synproxy.h header.
Move it to the nf_synproxy.h header.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_icmpv6.h contains two object macros which duplicate macros
in linux/icmpv6.h. The latter definitions are also visible wherever it
is included, so remove it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Include some headers in files which require them, and remove others
which are not required.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Several header-files, Kconfig files and Makefiles have trailing
white-space. Remove it.
In netfilter/Kconfig, indent the type of CONFIG_NETFILTER_NETLINK_ACCT
correctly.
There are semicolons at the end of two function definitions in
include/net/netfilter/nf_conntrack_acct.h and
include/net/netfilter/nf_conntrack_ecache.h. Remove them.
Fix indentation in nf_conntrack_l4proto.h.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_conntrack_labels.h has no include guard. Add it.
The comment following the #endif in the nf_flow_table.h include guard
referred to the wrong macro. Fix it.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the net_device unregisters, clean up the offload rules before the
chain is destroy.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possibly for drivers to adjust the default max_mtu
by storing it in the hardware struct and using that value
for all interfaces.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1567738137-31748-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for packet mirroring and redirection. The
nft_fwd_dup_netdev_offload() function configures the flow_action object
for the fwd and the dup actions.
Extend nft_flow_rule_destroy() to release the net_device object when the
flow_rule object is released, since nft_fwd_dup_netdev_offload() bumps
the net_device reference counter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
