Enable support for cbus gpios on FT232H. The cbus configuration is
stored in two words in the EEPROM at byte-offset 0x1a with the mux
config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be
configured as I/O mode).
Tested using FT232H by configuring one ACBUS pin at a time.
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Matthew Michilot <matthew.michilot@gmail.com>
[ johan: fix copy-paste error in commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8b(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8c(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fb Prot=ff Driver=qmi_wwan
E: Ad=8d(I) Atr=03(Int.) MxPS= 64 Ivl=5ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In 22b8:900e "qc_dload" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=900e Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
And in 22b8:4281 "ram_downloader" mode the device shows up as:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=4281 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=fc Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Lars Melin <larsm17@gmail.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXRxL/gAKCRALxc3C7H1l
CKHnAQDsaOTD7f5Rhn2x0VapiuuxC3BcSHDgizmPcIt2f8F1yQEAgLvMy1//N75O
XTG6rLe6EsYc/fHj3csdgCURSMZVzQw=
=wAe3
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.3-rc1
Here are the USB-serial updates for 5.3-rc1; just some new device ids
this time.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.3-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for isodebug v1
USB: serial: option: add support for GosunCn ME3630 RNDIS mode
This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.
A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Telit LE910Cx 0x1260 and 0x1261 compositions.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is adds the vendor and device id for the AT-VT-Kit3 which is a
pl2303-based device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement Fintek F81232 break on/off with LCR register.
It's the same with 16550A LCR register layout.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: fix corrupt line settings on break due to missing shadow_lcr
update in set_termios() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
F81232 Clock registers (106h)
Bit1-0: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 will report data and LSR with bulk like following format:
bulk-in data: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]...
LSR will auto clear frame/parity/break error flag when reading by H/W,
but overrrun will only cleared when reading LSR. So this patch add a
worker to read LSR when overrun and flush the worker on close() &
suspend().
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81232 will use interrupt worker to handle MSR change.
This patch will fix the issue that interrupt work should stop
in close() and suspend().
This also fixes line-status events being disabled after a suspend cycle
until the port is re-opened.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: amend commit message ]
Fixes: 87fe5adcd8 ("USB: f81232: implement read IIR/MSR with endpoint")
Cc: stable <stable@vger.kernel.org> # 4.1
Signed-off-by: Johan Hovold <johan@kernel.org>
Gustavo has been working to fix up all of the switch statements that
"fall through" such that we can eventually turn on
-Wimplicit-fallthrough. As part of that, the io_edgeport.c driver is a
bit "messy" with the parsing logic of a data packet. Clean that logic
up a bit by unindenting one level of the logic, and properly label
/* Fall through */ to make gcc happy.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when there was only a
single read URB.
Also convert the throttled flag to an atomic bit flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Override the initial terminal settings provided by core directly instead
of first resetting them to tty_std_termios.
Also reorder the cflags as they are usually seen (in bit order).
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop bogus TIOCM_CTS, which is not a cflag, from the initial terminal
settings.
Note that the corresponding bit is already set by CS8.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that init_termios() is only called on first use, we can clean up the
cypress_m8 initial-termios handling.
Note that only the earthmate chip type used settings different from the
defaults provided by USB serial core, and that the chip type is indeed
known when init_termios is called at tty-install time.
Signed-off-by: Johan Hovold <johan@kernel.org>
The initial terminal settings set by the driver matches the default
settings provided by core so drop the redundant init_termios callback.
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB-serial driver init_termios callback is used to override the
default initial terminal settings provided by USB-serial core.
After a bug was fixed in the original implementation introduced by
commit fe1ae7fdd2 ("tty: USB serial termios bits"), the init_termios
callback was no longer called just once on first use as intended but
rather on every (first) open.
This specifically meant that the terminal settings saved on (final)
close were ignored when reopening a port for drivers overriding the
initial settings.
Also update the outdated function header referring to the creation of
termios objects.
Fixes: 7e29bb4b77 ("usb-serial: fix termios initialization logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up set_termios() by adding missing white space around operators
and making a couple of continuation lines more readable.
Also drop a couple of redundant braces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up modem-control handling somewhat by adding missing whitespace
around operators and splitting a long statement in two.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add helper function to update register bits instead of overwriting the
entire control register when updating the flow-control settings.
This specifically avoids having the tranceiver suspend mode (bit 0)
depend on the flow control setting.
The tranceiver is currently configured at probe to be disabled during
suspend, but this was overridden when disabling flow control or enabling
xon/xoff.
Fixes: 715f9527c1 ("USB: flow control fix for pl2303")
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older pl2303 devices do not support automatic xon/xoff flow control, so
add add a flag to prevent trying to enable it for legacy device types.
Refactor the IXON test into a helper function to improve readability.
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver. The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes: ec0cd94d88 ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7PogAKCRALxc3C7H1l
CLtbAP9N7qnHiOflSg8sK3E4hBI5ZaVKQuJwObEOMJY+s6jeYwD1E3sbyWKGHu+2
R8Px/FbKC3JWMUIhO7bVlyvsQDcQAA==
=hG64
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7M3AAKCRALxc3C7H1l
CBUpAQD/N1G1G38alGS0zwn/u9krsVyLm5Y1gK8MWXvpkcGBXwEAoSYrMjoRAAdR
Ks4rQdSyYonbE3zENXp5d3beCRM4pQY=
=GQ5N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is how this device appears in kernel log:
usb 3-1: new full-speed USB device number 18 using xhci_hcd
usb 3-1: New USB device found, idVendor=0b00, idProduct=3070
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1: Product: Ingenico 3070
usb 3-1: Manufacturer: Silicon Labs
usb 3-1: SerialNumber: 0001
Apparently this is a POS terminal with embedded USB-to-Serial converter.
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add minimum baud rate to the cp210x driver.
According to the datasheet for CP2105, the SCI supports 2400 as the
lowest baud rate. As this is not heeded in the current code, an error
message 'failed set req 0x1e size 4 status: -32' when trying to set a
lower baud rate such as 300.
The other cp210x models to date supports a minimum baud rate of 300.
Signed-off-by: Johanna Abrahamsson <johanna.abrahamsson@afconsult.com>
[ johan: simplify min_speed init, move clamp after comment, and drop
unused serial-data pointer from cp210x_get_actual_rate() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP2104 chips feature 4 controllable GPIO pins, which are similar to
the ones on CP2102N chip (output-only when push-pull, output or
simulated input mode when open-drain).
Add support for the GPIO pins for cp210x driver. The pin get/set routine
is shared with CP2102N, but the pinconf initialization code is not
shared because the acquisition of GPIO configuration in OTP ROM is
similar to CP2105, not CP2102N.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Johan Hovold <johan@kernel.org>
The QFN28 package version of the CP2102N has three additional gpio pins.
Add support for these.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The keyspan_usa??msg.h files are under a BSD-3 style license, so
properly label them as such with a SPDX line at the top of the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add new PID to support PL2303TB (TYPE_HX)
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7da8 ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org> # 4.20
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXBva9AAKCRALxc3C7H1l
CP6XAQClpmmKj59AiAJK+hlWIbNpznPUUrkGHS7mFyuWkDrllQEAsK2IofNWbs9y
g0ot/v4UgUVZHySGl5yYoV4A0uKJdAQ=
=oyPx
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 4.21-rc1
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: serial: mos7840: remove set but not used variables 'number, serial'
USB: serial: mos7840: add a product ID for the new product
USB: serial: mos7840: clean up register handling
USB: serial: ftdi_sio: use rounding when calculating baud rate divisors
USB: serial: f81534: fix reading old/new IC config
USB: serial: mos7840: remove set but not used variables 'st, data1, iflag'
USB: serial: quatech2: remove set but not used variable 'port_priv'
Add device ids to pl2303 for the HP POS pole displays:
LM920: 03f0:026b
TD620: 03f0:0956
LD960TA: 03f0:4439
LD220TA: 03f0:4349
LM940: 03f0:5039
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_send_cmd_write_baud_rate':
drivers/usb/serial/mos7840.c:1584:16: warning:
variable 'number' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_change_port_settings':
drivers/usb/serial/mos7840.c:1695:21: warning:
variable 'serial' set but not used [-Wunused-but-set-variable]
'number' never used since introduction in commit 3f5429746d ("USB: Moschip
7840 USB-Serial Driver")
'serial' not used since commit 5833041f1b ("USB: serial: remove unnecessary
reinitialisations of urb->dev")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a new PID 0x7843 to the driver.
Let the new products be able to set up 3 serial ports with the driver.
Note that this depends on e8603076f5 ("USB: serial: mos7840: clean up
register handling").
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: mention dependency in case anyone wants to backport this ]
Signed-off-by: Johan Hovold <johan@kernel.org>
In the read/write function, set port 2 independently in the 2-port case.
When setting the offset of port registers, the offset between port 1 and
other ports is different, so port 1 is set independently.
Then in the rest of ports, the port 2 between 2-ports case and 4-ports case
is different, so port 2 in 2-ports case is set independently.
Specifically, port 2 in the 2-port case maps to the registers used by
port 3 in the 4-port case.
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: simplify register-offset handling at port probe, add a comment
and amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Improve baud-rate generation by using rounding-to-closest instead of
truncation in divisor calculation.
Results have been verified by logic analyzer on an FT232RT (232BM) chip.
The following table shows the wanted baud rate, the baud rate obtained
with the old method (truncation), with the new method (rounding) and the
baud rate generated by the windows 10 driver. The numbers in parentheses
is the error.
+- Wanted --+------ Old -------+------ New -------+------ Win -------+
| 9600 | 9600 (0.00%) | 9604 (0.05%) | 9605 (0.05%) |
| 19200 | 19200 (0.00%) | 19199 (0.01%) | 19198 (0.01%) |
| 38400 | 38395 (0.01%) | 38431 (0.08%) | 38394 (0.02%) |
| 57600 | 57725 (0.22%) | 57540 (0.10%) | 57673 (0.13%) |
| 115200 | 115307 (0.09%) | 115330 (0.11%) | 115320 (0.10%) |
| 921600 | 919963 (0.18%) | 920386 (0.13%) | 920810 (0.09%) |
| 961200 | 996512 (3.67%) | 956480 (0.49%) | 956937 (0.44%) |
+-----------+------------------+------------------+------------------+
The error due to noise in the measurements is in the order of a few
tenths of a %. As can be seen, the baud rate is significantly improved
for some rates (e.g. 961200), and corresponds to the output given by the
windows driver.
The theoretical baud rate has been calculated for all baud rates from 1
to 3M, and as expected, the error is centered around 0, with a triangle
shape instead of a sawtooth, so the maximum error is decreased to half.
Signed-off-by: Nikolaj Fogh <nikolajfogh@gmail.com>
[ johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
+00h: to indicate the section is valid
+01h~04h: UART Mode & port availability
+05h~08h: Output pin control on IC power on
+09h~12h: Output pin control on working <-- New added
Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.
This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_interrupt_callback':
drivers/usb/serial/mos7840.c:604:14: warning:
variable 'st' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_write':
drivers/usb/serial/mos7840.c:1303:17: warning:
variable 'data1' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c:1700:11: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
They are never used since introduction in commit 3f5429746d ("USB:
Moschip 7840 USB-Serial Driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/quatech2.c: In function 'qt2_process_read_urb':
drivers/usb/serial/quatech2.c:503:27: warning:
variable 'port_priv' set but not used [-Wunused-but-set-variable]
It not used any more after commit 2be818a116 ('Revert "USB: quatech2:
only write to the tty if the port is open."')
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=V6Jo
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.20-rc1
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cypress_m8: remove set but not used variable 'iflag'
USB: serial: cypress_m8: fix interrupt-out transfer length
USB: serial: ftdi_sio: add support for FT232R CBUS gpios
USB: serial: ftdi_sio: fix gpio name collisions
USB: serial: ftdi_sio: implement GPIO support for FT-X devices
USB: serial: cypress_m8: fix spelling mistake "retreiving" -> "retrieving"
... and fix the return value - on success it used to have ioctl(2)
fill the user-supplied struct serial_struct and return -ENOTTY.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
add such methods for usb_serial_driver, provide tty_operations
->[sg]et_serial() calling those. For now the lack of methods
in driver means ENOIOCTLCMD from usb-serial ->[sg]et_serial(),
making tty_ioctl() fall back to calling ->ioctl(). Once all
drivers are converted, we'll be returning -ENOTTY instead,
completing the switchover.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/cypress_m8.c: In function 'cypress_set_termios':
drivers/usb/serial/cypress_m8.c:866:18: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1 ("cypress_m8: use usb_fill_int_urb where appropriate")
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.
Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:
gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'
and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):
sysfs: cannot create duplicate filename '/class/gpio/CBUS0'
Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch allows using the CBUS pins of FT-X devices as GPIO in CBUS
bitbanging mode. There is no conflict between the GPIO and VCP
functionality in this mode. Tested on FT230X and FT231X.
As there is no way to request the current CBUS register configuration
from the device, all CBUS pins are set to a known state when the first
GPIO is requested. This allows using libftdi to set the GPIO pins
before loading this module for UART functionality, a behavior that
existing applications might be relying upon (though no specific case
is known to the authors of this patch).
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: minor style changes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
These ioctls never reach driver's ->ioctl() - tty_ioctl() handles
them on its own. ->tiocm[gs]et() is what actually gets called,
and mos7720 provides those, with results equivalent to what the
unreachable code would be doing when called.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow matching on interfaces having two endpoints by adding a new
device-id flag.
This allows for the handling of devices whose interface numbers can
change (e.g. Quectel EP06) to be contained in the device-id table.
Tested-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB
configuration, without the VID/PID or configuration number changing.
When the configuration is updated and interfaces are added/removed, the
interface numbers are updated. This causes our current code for matching
EP06 not to work as intended, as the assumption about reserved
interfaces no longer holds. If for example the diagnostic (first)
interface is removed, option will (try to) bind to the QMI interface.
This patch improves EP06 detection by replacing the current match with
two matches, and those matches check class, subclass and protocol as
well as VID and PID. The diag interface exports class, subclass and
protocol as 0xff. For the other serial interfaces, class is 0xff and
subclass and protocol are both 0x0.
The modem can export the following devices and always in this order:
diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be
interface 0, and interface numbers 1-5 should be marked as reserved. The
three other serial devices can have interface numbers 0-3, but I have
not marked any interfaces as reserved. The reason is that the serial
devices are the only interfaces exported by the device where subclass
and protocol is 0x0.
QMI exports the same class, subclass and protocol values as the diag
interface. However, the two interfaces have different number of
endpoints, QMI has three and diag two. I have added a check for number
of interfaces if VID/PID matches the EP06, and we ignore the device if
number of interfaces equals three (and subclass is set).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
[ johan: drop uneeded RSVD(5) for ADB ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Movie Song <MovieSong@aten-itlab.cn>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0ukW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.19-rc1
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds GPIO support for CP2102N devices.
It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.
Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: fix style issues and a couple of minor bugs; use Karoly's
updated commit message ]
Acked-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.
Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.
Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.
To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).
As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.
This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.
As per the data sheets the following maximum speeds are used
cp2101 921.6 kbaud
cp2102/3 1 Mbaud
cp2104/8 2 Mbaud
cp2105
- ECI port 2 Mbaud
- SCI port 921.6 kbaud
while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.
Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <chris.jakob@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd67 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a "tty_" prefix to the tty "flag" variable to avoid any future
mixups with the recently added irq-mask "flags" one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Negative error code will be larger than sizeof().
Note that none of these bugs prevent errors from being detected, even if
the ir-usb one would cause a less precise debug message to printed.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[ johan: add comment about implications ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Signed-off-by: Karoly Pados <pados@pados.hu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEHszNKQClByu0A+9RQQ3kT97htJUFAlsPvjYRHGpvaGFuQGtl
cm5lbC5vcmcACgkQQQ3kT97htJV/DA/9Huw/RMPo8uSeTiBErvglMf6UJGU8m4qp
YKFzLCkyThPIBBDTYKe1pTWebx422EFCGJwm4zG309ZNxpBcDOmp19FMcQsqCoqN
nRANSJ6L73sbsOLy48/zv59z8vpvVLn0Ob1mQi6iM4KfDdor9PVwHH8zSFHVWO6M
izOLgfeRcfvp8OHPQEodFseQ25jH8SaKA4HSjDmr1vryiMxB8Bh7cVWovC0z2SP8
s8FseAgnhbGp1RF6S4CDUR0OIr064RvoLZjBjVe7iyRiNW6LeruO9I9ctHQQZAh+
D7iVFNj5xTeZQTfgXual7Vbvt5eOBpptcRJqI4Zr+8RR9yIGCpvSh8Kzufkl1uc2
i+0KSo/so2AjBiGS99fxNHrSMD30wL+9Vc2qsq0CuZdkbHamr/8FLtPIuPdq99CW
LBvjJxmzRTl2LDIWDa3fv5Dkfp42asWtg7iN33pf7UcobwgXT8MHrNd6rvsJTMg0
AZHVyZvuplWP3kyZlOCSbZEcIZGiV5lEKLnI0kDtc0io2pJ3+0D6Ys7+lz9o2IHx
zyznyB+dHoiPFd55BooFRIKN75uOLszzA0AhrZLGtUZ20gsdhfLWWgg9VzoaZUsz
NSJIV9tFbBYsnzLDX3W7Q1/VLuvYGidi8Hw7czR5mkWYWFIxShywf4xyaeY3VoiN
i73ad0YjmE8=
=gsOA
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.18-rc1
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Support hardware-level Xon/Xoff flow control in transmit direction with
pl2303.
I only know how to get the hardware to do IXON/!IXANY with ^S/^Q as control
characters, so I preserve the old behaviour for all other cases.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
[ johan: rewrite logic using pl2303_termios_change() helper ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
We already have the tty port when probing a usb-serial port so use
tty_port_register_device() directly instead of tty_port_install() later
to set up the port link.
This is a step towards enabling serdev for usb-serial (but we need to
determine how to handle hotplugging first).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for ublox R410M PID 0x90b2 USB modem to option
driver, this module supports LTE Cat M1 / NB1.
Interface layout:
0: QCDM/DIAG
1: ADB
2: AT
3: RMNET
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dwm-158 interface 4 and 5 doesn't answer to the AT commands
and doesn't appears a option interface.
Tested on openwrt distribution (kernel 4.14 using the old blacklist
definitions).
Lars Melin also writes:
Blacklisting interface 4 and 5 is correct because:
MI_00 D-Link Mobile Broadband Device (cdc_ether)
MI_02 D-Link HSPA+DataCard Diagnostics Interface (also ppp modem)
MI_03 D-Link HSPA+DataCard NMEA Device
MI_04 D-Link HSPA+DataCard Speech Port
MI_05 D-Link HSPA+DataCard Debug Port
MI_06 USB Mass Storage Device
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[ johan: add Lars's comment on the interface layout and reword summary ]
Cc: Lars Melin <larsm17@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB VID and PID for the USB serial console on some National
Instruments devices.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 79a0b33165.
Turns out this is not an FTDI device after all.
Fixes: 79a0b33165 ("USB: serial: ftdi_sio: add Id for Physik Instrumente E-870")
Reported-by: Martin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.17-rc1, including a
reimplementation of the option-driver interface masking which allows
for a more compact notation when adding new device entries.
Included are also a couple of clean ups and a new ftdi_sio device id.
All but the device-id commit have been in linux-next (without any
reported issues).
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=E3H0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.17-rc1
Here are the USB-serial updates for 4.17-rc1, including a
reimplementation of the option-driver interface masking which allows
for a more compact notation when adding new device entries.
Included are also a couple of clean ups and a new ftdi_sio device id.
All but the device-id commit have been in linux-next (without any
reported issues).
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for the Physik Instrumente E-870 PIShift Drive
Electronics, a Piezo motor driver.
Signed-off-by: Martin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: Clemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the USB class define rather than a magic number when refusing to
bind to mass-storage interfaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant interface-class test for Samsung GT-B3730 modems for
which we only match and probe the CDC data interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reimplement interface masking using device flags stored directly in the
device-id table. This will make it easier to add and maintain device-id
entries by using a more compact and readable notation compared to the
current implementation (which manages pairs of masks in separate
blacklist structs).
Two convenience macros are used to flag an interface as either reserved
or as not supporting modem-control requests:
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
.driver_info = NCTRL(0) | RSVD(3) },
For now, we limit the highest maskable interface number to seven, which
allows for (up to 16) additional device flags to be added later should
need arise.
Note that this will likely need to be backported to stable in order to
make future device-id backports more manageable.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
This adds a new device id for Chilitag devices to the pl2303 driver.
Reported-by: "Chu.Mike [朱堅宜]" <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_WO() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer mos_parport is being initialized to pp->private_data and
then the assignment is duplicated after a spin lock. Remove the
initialization as it occurs before the spin lock and it is a redundant
assignment.
Cleans up clang warnings:
drivers/usb/serial/mos7720.c:521:26: warning: Value stored to
'mos_parport' during its initialization is never read
drivers/usb/serial/mos7720.c:557:26: warning: Value stored to
'mos_parport' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FS040U modem is manufactured by omega, and sold by Fujisoft. This patch
adds ID of the modem to use option1 driver. Interface 3 is used as
qmi_wwan, so the interface is ignored.
Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp>
Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.16-rc1, including:
- a fix for a potential sleep-while-atomic (warning) in an io_edgeport
error path
- removal of a dummy TIOCSSERIAL implementation in ark3116
- new features for Fintek F81532/534 devices:
- support for higher baud rates (up to 1.5 Mbps)
- support for auto-RTS (for RS-485)
- support for transceiver configuration
- support for detecting disabled ports
Included are also various clean ups.
All have been (at least compile tested) in linux-next without any
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ZTZB
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.16-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.16-rc1
Here are the USB-serial updates for 4.16-rc1, including:
- a fix for a potential sleep-while-atomic (warning) in an io_edgeport
error path
- removal of a dummy TIOCSSERIAL implementation in ark3116
- new features for Fintek F81532/534 devices:
- support for higher baud rates (up to 1.5 Mbps)
- support for auto-RTS (for RS-485)
- support for transceiver configuration
- support for detecting disabled ports
Included are also various clean ups.
All have been (at least compile tested) in linux-next without any
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz. But on some baud rate (384~500kps), the
TX side will send the data frame too close to treat frame error on RX
side. This patch will force all TX data frame with delay 1bit gap.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 can be disable port by manufacturer with
following H/W design.
1: Connect DCD/DSR/CTS/RI pin to ground.
2: Connect RX pin to ground.
In driver, we'll implements some detect method likes following:
1: Read MSR.
2: Turn MCR LOOP bit on, off and read LSR after delay with 60ms.
It'll contain BREAK status in LSR.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In the original code, We'll read configuration in calc_num_ports()
and read again in attach(). In fact, we can move all content from
attach() to calc_num_ports() to simplify the code.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: replace commit summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.
Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch moves TIOCGSERIAL ioctl case to get_serial_info function.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: keep the automatic __user pointer variable in ioctl callback ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch removes unused TIOCSSERIAL ioctl case and adds the default block
to the switch. This will make the ioctl return -ENOTTY to user space (e.g.
setserial), which indicates that TIOCSSERIAL really isn't supported for
these devices currently.
Note that these (dummy) ioctl implementations where added by commit
2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl
calls.") back in 2006. This in turn appears to have been triggered by a
change in a user space tool, wvdial, which started erroring out if
either was missing.
There are some bug reports about that against wvdial from around that
time, and looking at the wvstreams (library) code now, it looks like the
issue has indeed been resolved by handling errors more gracefully (e.g.
just logging them).
User space really should not make assumptions about these ioctl always
being implemented, but if this turns out to be a problem for anyone
using this driver, we'll add TIOCSSERIAL back in some form.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: amend commit message with backstory ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds the ELV ALC 8xxx Battery Charging device
to the list of USB IDs of drivers/usb/serial/cp210x.c
Signed-off-by: Christian Holl <cyborgx1@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add IDs for the OneTouch Verio IQ that comes with an embedded
USB-to-serial converter.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for PID 0x1101 of Telit ME910.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB vendor id and product id for Linux USB Debug Target is added.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
write_reg returns 0 on success, we can make it more explicit by returning
number 0 instead of result variable.
read_reg should return 0 on success since this is a more common pattern.
The user of read_reg has been clean-up and should be at the same commit.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The assignment of DIV to itself is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel
development board (EVB). The USB id is added to option.c to allow
DIAG,GPS,AT and modem communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
This updates the remaining drivers/usb/*Makefile* that were missing SPDX
identifiers. They all get the following identifier:
SPDX-License-Identifier: GPL-2.0
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Johan Hovold <johan@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The product ID for "Linux USB GDB Target device" has been
changed. Change the driver binding table accordingly.
This patch should be back-ported to kernels as old as v4.12,
that contain the commit 57fb47279a ("usb/serial: Add DBC
debug device support to usb_debug").
Cc: <stable@vger.kernel.org> # v4.12+
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several GPL-2.0 drivers used "GPL" rather than "GPL v2" in their
MODULE_LICENSE macros; fix the macros to match the licenses.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.15-rc1, including:
- three fixes for longstanding issues in garmin_gps and metro-usb which
could lead to NULL-pointer dereferences and memory leaks
- a workaround for broken f81534 firmware-handling of overruns
- f81534 break support, and
- conversion to timer_setup()
Included are also various clean ups and a new qcserial device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GqYH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.15-rc1
Here are the USB-serial updates for 4.15-rc1, including:
- three fixes for longstanding issues in garmin_gps and metro-usb which
could lead to NULL-pointer dereferences and memory leaks
- a workaround for broken f81534 firmware-handling of overruns
- f81534 break support, and
- conversion to timer_setup()
Included are also various clean ups and a new qcserial device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement Fintek f81534 break on/off with LCR register.
It's the same with 16550A LCR register layout.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 without this patch will hang-up on data overrun.
It's caused by enable LSR interrupt in IER by default and occur data
overrun, the chip will busy for process LSR interrupt but not read LSR
internally. It will not responed for USB control endpoint0 and we can't
read LSR from driver in this situration.
So we'll disable the LSR interrupt in probe() and submit the LSR worker to
clear LSR state when reported LSR error bit with bulk-in data in
f81534_process_per_serial_block().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add USB PID/VID for Sierra Wireless EM7355 LTE modem QDL firmware update
mode.
Signed-off-by: Douglas Fischer <douglas.fischer@outlook.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115014
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the usb-serial-core USB driver that was registered at module init
but then never used.
This was a remnant dating back to 2004 (!) when this struct usb_driver
was used for the generic driver; see commit bbc53b7d7322 ("USB: fix bug
where removing usb-serial modules or usb serial devices could oops") in
the tglx bitkeeper-history archive.
Note that every usb-serial driver (including the generic one) registers
its own USB (interface) driver along with its usb-serial bus drivers.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
One class of "unidirectional" devices managed by this driver uses an
interrupt-out endpoint to send control messages at open and close. Due
to a missing endpoint sanity check, this could result in an interrupt
URB being submitted to endpoint 0 instead. This would be caught by
USB core (without a WARN dump), but let's verify that the expected
endpoints are present at probe rather than when a port is later opened.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Let usb-serial core verify that the interrupt-in endpoint is present
when binding the interface instead of the driver verifying this at every
open.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to kill the interrupt-in URB after a failed open request.
Apart from saving power (and avoiding stale input after a later
successful open), this also prevents a NULL-deref in the completion
handler if the port is manually unbound.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 704577861d ("USB: serial: metro-usb: get data from device in Uni-Directional mode.")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the somewhat convoluted init-session logic to improve
readability.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port device for any init-session error and debug messages,
remove one redundant debug message and simplify one error message.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop out-commented timer expiry initialisation which would not even
compile anymore.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to free the port private data before returning after a failed
probe attempt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop any submitted interrupt and bulk-out URBs before
returning after failed probe and when the port is being unbound to avoid
later NULL-pointer dereferences in the completion callbacks.
Also fix up the related and broken I/O cancellation on failed open and
on close. (Note that port->write_urb was never submitted.)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 51a2f077 ("USB: introduce usb_anchor")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johan Hovold <johan@kernel.org>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to reset the USB-console port pointer when console setup fails
in order to avoid having the struct usb_serial be prematurely freed by
the console code when the device is later disconnected.
Fixes: 73e487fdb7 ("[PATCH] USB console: fix disconnection issues")
Cc: stable <stable@vger.kernel.org> # 2.6.18
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A clean-up patch removing two redundant NULL-checks from the console
disconnect handler inadvertently also removed a third check. This could
lead to the struct usb_serial being prematurely freed by the console
code when a driver accepts but does not register any ports for an
interface which also lacks endpoint descriptors.
Fixes: 0e517c93dc ("USB: serial: console: clean up sanity checks")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Dell Wireless 5819/5818 devices are re-branded Sierra Wireless MC74
series which will by default boot with vid 0x413c and pid's 0x81cf,
0x81d0, 0x81d1, 0x81d2.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the USB device id for the ELV TFD500 data logger.
Signed-off-by: Andreas Engel <anen-nospam@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When adding GPIO support for the cp2105, the mentioned commit by Martyn
Welch introduced a query for the part number of the chip. Unfortunately
the driver aborts probing when this query fails, so currently the driver
can not be used with chips not supporting this query.
I have a data cable for Siemens mobile phones (ID 10ab:10c5) where this
is the case.
With this patch the driver can be bound even if the part number can not
be queried.
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Signed-off-by: Sebastian Frei <dr.nop@gmx.net>
[ johan: amend commit message; shorten error message and demote to
warning; drop unnecessary move of usb_set_serial_data() ]
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
This commit adds support for TP-Link LTE mPCIe module is used
in in TP-Link MR200v1, MR6400v1 and v2 routers.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add CYPRESS_VID vid and CYPRESS_WICED_BT_USB and CYPRESS_WICED_WL_USB
device IDs to ftdi_sio driver.
Signed-off-by: Jeffrey Chu <jeffrey.chu@cypress.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device id for D-Link DWM-222.
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Johan Hovold <johan@kernel.org>
The German Telekom offers a ZigBee USB Stick under the brand name Qivicon
for their SmartHome Home Base in its 1. Generation. The productId is not
known by the according kernel module, this patch adds support for it.
Signed-off-by: Stefan Triller <github@stefantriller.de>
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the code like the rest of the kernel.
Also use inline instead of __inline__.
Link: http://lkml.kernel.org/r/a5072b74b6c293e6ec93c4900482e9d3267f15b2.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB set
of patches, so here they are in a separate pull request.
Nothing major here a all, just 3 small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWV9FRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHxgCfTT31v4FaxH2k76qA1ZnHdXWHqyQAn3oyOE4T
uJhpp1FbFR1VNXM/jRox
=PCPm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Added the USB serial device ID for the CEL ZigBee EM3588
radio stick.
Signed-off-by: Jeremie Rapin <rapinj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate errnos for late probe errors (e.g. -ENOMEM on allocation
failures) instead of always returning -EIO.
Note that some drivers are currently returning -ENODEV from their attach
callbacks when a device is not supported, but this has also been mapped
to -EIO.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the probe callback more readable by refactoring the port
endpoint-resource setup by adding four helper functions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the broken alt_speed code, and warn when trying to set the line
speed using TIOCSSERIAL and SPD flags.
The use of SPD flags to set the line speed has been deprecated since
v2.1.69 and support for alt_speed (e.g. "warp") has even been removed
from TTY core in v3.10 by commit 6865ff222c ("TTY: do not warn about
setting speed via SPD_*"), effectively breaking all driver
implementations of this except for serial core.
Also remove the verbose and outdated comment on how to set baud rates.
Note that setting a custom divisor will continue to work with the
caveat that 38400 must again be selected every time the divisor is
changed since v2.6.24 and commit 669a6db103 ("USB: ftd_sio: cleanups
and updates for new termios work") which started reporting back the
actual baud rate used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcserial driver fails to expose the .tiocmget and .tiocmset methods
available from usb_wwan. These methods are required by ioctl commands
dealing with the modem control signals DTR, RTS, etc.
With these methods not set ioctl calls intended to control the DTR state
will fail. For example, pppd drops and raises DTR in preparation to
dialing the modem, which handles the case of the modem already being
connected by making it hang up and return to command mode. DTR control
being unavailable will lead to a protracted failure to connect as the
modem will be stuck in a state not responsive to command.
I have tested that with this patch the described case is handled
successfully. There is an analogous method for .ioctl available from
usb_wwan (as used in option.c) but I conservatively omitted that for
lack of familiarity.
Signed-off-by: Magnus Lynch <maglyx@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some local constants don't change from call to call and are good
candidates to become static. This will prevent copying of these
constants to stack during runtime.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use new USB device IDs for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for recognition of ARM-USB-TINY(H) devices which
are almost identical to ARM-USB-OCD(H) but lacking separate barrel jack
and serial console.
By suggestion from Johan Hovold it is possible to replace
ftdi_jtag_quirk with a bit more generic construction. Since all
Olimex-ARM debuggers has exactly two ports, we could safely always use
only second port within the debugger family.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a division-by-zero in set_termios when debugging is enabled and a
high-enough speed has been requested so that the divisor value becomes
zero.
Instead of just fixing the offending debug statement, cap the baud rate
at the base as a zero divisor value also appears to crash the firmware.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop erroneous cpu_to_le32 when setting the baud rate, something which
corrupted the divisor on big-endian hosts.
Found using sparse:
warning: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] val
got restricted __le32 [usertype] <noident>
Fixes: af2ac1a091 ("USB: serial mct_usb232: move DMA buffers to heap")
Cc: stable <stable@vger.kernel.org> # 2.6.34
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing endianness conversion when printing the supported baud
rates.
Found using sparse:
warning: restricted __le16 degrades to integer
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") enables unprivileged users to set the FTDI latency timer,
but there was a logic flaw that skipped sending the corresponding
USB control message to the device.
Specifically, the device latency timer would not be updated until next
open, something which was later also inadvertently broken by commit
c19db4c9e4 ("USB: ftdi_sio: set device latency timeout at port
probe").
A recent commit c6dce26266 ("USB: serial: ftdi_sio: fix extreme
low-latency setting") disabled the low-latency mode by default so we now
need this fix to allow unprivileged users to again enable it.
Signed-off-by: Anthony Mallet <anthony.mallet@laas.fr>
[johan: amend commit message]
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Fixes: c19db4c9e4 ("USB: ftdi_sio: set device latency timeout at port probe").
Cc: stable <stable@vger.kernel.org> # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
Pull x86 debug updates from Ingo Molnar:
"The biggest update is the addition of USB3 debug port based
early-console.
Greg was fine with the USB changes and with the routing of these
patches:
https://www.spinics.net/lists/linux-usb/msg155093.html"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
usb/doc: Add document for USB3 debug port usage
usb/serial: Add DBC debug device support to usb_debug
x86/earlyprintk: Add support for earlyprintk via USB3 debug port
usb/early: Add driver for xhci debug capability
x86/timers: Add simple udelay calibration
Here are the USB-serial updates for 4.12, including:
- support for devices with up to 16 ports (e.g. some Moxa devices)
- support for endpoint sanity checks in core, which allows for code sharing
and avoids allocating resources for rejected interfaces
- support for endpoint-port remapping, which allows some driver hacks to
be removed as well as omninet to use the generic write implementation
- removal of an obsolete tty open-race workaround which prevented a
port from being opened immediately after having been registered
- generic-driver support for interfaces with just a bulk-in endpoint
- improved ftdi_sio event-char and latency-timer handling
- improved ftdi_sio support for some broken BM chips
Included are also various clean ups and a new ftdi_sio device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=cSzy
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.12-rc1
Here are the USB-serial updates for 4.12, including:
- support for devices with up to 16 ports (e.g. some Moxa devices)
- support for endpoint sanity checks in core, which allows for code sharing
and avoids allocating resources for rejected interfaces
- support for endpoint-port remapping, which allows some driver hacks to
be removed as well as omninet to use the generic write implementation
- removal of an obsolete tty open-race workaround which prevented a
port from being opened immediately after having been registered
- generic-driver support for interfaces with just a bulk-in endpoint
- improved ftdi_sio event-char and latency-timer handling
- improved ftdi_sio support for some broken BM chips
Included are also various clean ups and a new ftdi_sio device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.
Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant calls to tty_buffer_request_room and use the more
efficient tty_insert_flip_char when inserting single characters.
Signed-off-by: Johan Hovold <johan@kernel.org>
The transfer buffers and URBs are allocated and initialised by USB
serial core during probe, and there's no need to check for NULL transfer
buffers in the bulk-in completion handlers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit a65a6f14dc ("USB: serial: fix race between probe and open")
fixed a race between probe and open, which could lead to crashes when a
not yet fully initialised port was being opened.
This race was later incidentally closed by commit 7e73eca6a7 ("TTY:
move cdev_add to tty_register_device") which moved character-device
registration from tty_register_driver to tty_register_device, which
isn't called until the port has been fully set up.
Remove the now redundant workaround which had the negative side effect
of not allowing a port to be opened immediately after user space had
been notified of a new tty device.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop some unnecessary termios-flag debugging that have been faithfully
reproduced in a few old drivers, including the "clfag" typo and all.
This also addresses a compiler warning on sparc where tcflag_t is
unsigned long and would have required an explicit cast.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add an explicit sanity check to make sure we have the expected
endpoints. This will provide a descriptive error message in case an
expected endpoint is missing when probing.
Note that the driver already gracefully fails to probe (albeit with a
less descriptive error message) if a bulk-in endpoint is missing, and an
attempt to write to a port whose device lack a bulk-out endpoint would
fail with -ENODEV.
Signed-off-by: Johan Hovold <johan@kernel.org>
Print a message and register two ports for interfaces for which we do
not know how many ports there are instead of binding, allocating
resources, but not register any ports.
This provides a hint that anyone adding a dynamic device id must also
provide a reference id (driver info) from which the port count can be
retrieved, for example:
echo <vid> <pid> 0 0x110A 0x1410 > new_id
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
treo devices instead of poking around in the port structures after the
ports have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
clie_5 devices.
Note that the same bulk-out endpoint is being used for both ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant calc_num_ports callback from the clie_5 type, for
which the callback always returns zero and hence falls back to the type
num_ports value (2).
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that the endpoint-port mapping has been properly set up during
probe, we can switch to using the more efficient generic write
implementation.
Note that this currently means that chars_in_buffer now overcounts
slightly as we always write a full endpoint-sized packet.
Also add a copyright entry.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices use the second bulk-out endpoint for writing. Instead of
using the resources of the second port structure setup by core, use the
new endpoint-remap functionality to simply ignore the first bulk-out
endpoint. This specifically avoids allocating resources for the unused
endpoint.
Note that the disconnect callback was always redundant as all URBs would
have been killed by USB core on disconnect.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the endpoint sanity check by letting core verify the single
interrupt endpoint, and verifying the bulk endpoints in calc_num_ports
after having determined the number of ports.
Note that the static type num_ports field was neither correct or used
(since calc_num_ports never returns zero).
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver have treated the interrupt endpoint as optional despite it
always being present (according to the datasheet). Let's consider it
mandatory instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the mcs7715 port setup by using the new endpoint-remap
functionality provided by core. Instead of poking around in internal
port-structure fields, simply swap the endpoint descriptors of the two
ports in calc_num_ports before the port structures are even allocated.
Note that we still need to override the default interrupt completion
handler.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant read-urb check from open. The presence of a bulk-in
endpoint is now verified during probe and core has allocated the
corresponding resources.
Signed-off-by: Johan Hovold <johan@kernel.org>
Verify that the required interrupt endpoint is present at probe rather
than at open to avoid allocating resources for an unusable device.
Note that the endpoint is only required when in download mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to verify that the
required endpoints are present when in download mode.
This avoids allocating port resources for interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports callback to ignore unused endpoints.
The driver binds to any interface with at least one bulk-in and one
bulk-out endpoint, but some devices can have three or more endpoints of
which only either the first or second pair of endpoints is needed.
This avoids allocating resources for unused endpoints, and specifically
a port is no longer registered for the unused first endpoint pair when
there are more than three endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to determine which
interface to bind to in order to avoid allocating port-resources for
interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
We can now abort probe early after an error in calc_num_ports by
returning an errno instead of attempting to continue probing but not
register any ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present and moving the max-packet check to
calc_num_ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than probe callback to determine which
interface to bind to.
This allows us to remove some duplicate code.
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement the "horrible endpoint hack" for some legacy devices as a
quirk and clean up the code somewhat.
Note that the bulk-endpoint check can be removed as core will already
have verified this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Some pl2303 devices require the use of the interrupt endpoint of an
unrelated interface. This has so far been dealt with in usb-serial core,
but can now be moved to a driver calc_num_ports callback.
Note that we relax the endpoint requirements checked by core and instead
verify that we have an interrupt-in endpoint in calc_num_ports for all
devices so that the hack can first be applied.
Signed-off-by: Johan Hovold <johan@kernel.org>
Relax the generic driver bulk-endpoint requirement. The driver handles
devices without bulk-out endpoints just fine these days.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a calc_num_ports callback to the generic driver and verify that the
device has the required endpoints there instead of in core.
Note that the generic driver num_ports field was never used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a probe callback to the generic driver and print the
only-for-testing message there.
This is a first step in getting rid of the CONFIG_USB_SERIAL_GENERIC
ifdef from usb-serial core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow subdrivers to modify the port-endpoint mapping by passing the
endpoint descriptors to calc_num_ports.
The callback can now also be used to verify that the required endpoints
exists and abort probing otherwise.
This will allow us to get rid of a few hacks in subdrivers that are
already modifying the port-endpoint mapping (or aborting probe due to
missing endpoints), but only after the port structures have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a Dell branded Sierra Wireless EM7455.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver registers four ports but uses five bulk-endpoint
pairs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver uses the second bulk-out endpoint for writing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver expects two bulk-endpoint pairs also for mcs7715
devices for which only one serial port is registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Also require the presence of a bulk-out endpoint, something which
prevents the driver from trying to send bulk messages over the control
pipe should a bulk-out endpoint be missing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that this driver uses an additional bulk-endpoint pair as an
out-of-band port.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow drivers to specify a minimum number of endpoints per type, which
USB serial core will verify after subdriver probe has returned (where
the current alternate setting may have been changed).
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") USB core guarantees that there are no more than 15 endpoint
descriptors per type (and altsetting) so the corresponding overflow
checks can now be replaced with a compile-time check on the array sizes
(and indirectly the maximum number of ports).
Signed-off-by: Johan Hovold <johan@kernel.org>
Refactor and clean up endpoint handling.
This specifically moves the endpoint-descriptor arrays of the stack.
Note that an err_free_epds label is not yet added to avoid a compilation
warning when neither CONFIG_USB_SERIAL_PL2303 or
CONFIG_USB_SERIAL_GENERIC is selected.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The 'store' function for the "event_char" device attribute currently
expects a base 10 value. The value is composed of an enable bit in bit
8 and an 8-bit "event character" code in bits 7 to 0. It seems
reasonable to allow hexadecimal and octal numbers to be written to the
device attribute in addition to decimal. Make it so.
Change the debug message to show the value in hexadecimal, rather than
decimal.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "event_char" device attribute value, when written, is interpreted as
an enable bit in bit 8, and an "event character" in bits 7 to 0.
Return an error -EINVAL for out-of-range values. Use kstrtouint() to
parse the integer instead of the obsolete simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Valid latency timer values are between 1 ms and 255 ms in 1 ms steps.
The store function for the "latency_timer" device attribute currently
allows any value, although only the lower 16 bits will be sent to the
device, and the device only stores the lower 8 bits. The hardware
appears to accept the (invalid) value 0 and treats it the same as 1
(resulting in a latency of 1 ms).
Change the latency_timer_store() function to accept only the values 0 to
255, returning an error -EINVAL for out-of-range values. Call
kstrtou8() to parse the integer instead of the obsolete
simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If a BM type chip has iSerialNumber set to 0 in its EEPROM, an incorrect
value is read from the bcdDevice field of the USB descriptor, making it
look like an AM type chip. Attempt to correct this in
ftdi_determine_type() by attempting to read the latency timer for an AM
type chip if it has iSerialNumber set to 0. If that succeeds, assume it
is a BM type chip.
Currently, read_latency_timer() bails out without reading the latency
timer for an AM type chip, so factor out the guts of
read_latency_timer() into a new function _read_latency_timer() that
attempts to read the latency timer regardless of chip type, and returns
either the latency timer value or a negative error number.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The latency timer was introduced with the FT232BM and FT245BM chips. Do
not bother attempting to read or write it for older chip versions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.
This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20 ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d38088921 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Cc: stable <stable@vger.kernel.org> # v2.6.30: 2d38088921
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9eBj
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1 part 2
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Move all declarations and definitions in keyspan.h to keyspan.c, which
is the only place were they are used.
This specifically moves the driver device-id tables and usb-serial
driver definitions to the source file where they are expected to be
found.
While at it, fix up some multi-line comments and minor white-space
issues (spaces instead of tabs and superfluous white space).
Note that the information in the comment header of the removed header
file is also present in the source file.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move the driver device-id tables and usb-serial driver definitions to
the source file where they are expected to be found.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The adaptor on Analog Devices EVAL-ADXL362Z development board is used
to flash and debug firmware of on-board Renesas RL78/G13 MCU.
Also added support of the 153600 baud rate, since the stock firmware
uses it.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ma49
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix another NULL-pointer dereference at open should a malicious device
lack an interrupt-in endpoint.
Note that the driver has a broken check for an interrupt-in endpoint
which means that an interrupt URB has never even been submitted.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # v2.6.19: 5c75633ef7
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop two redundant NULL checks from usb_serial_console_disconnect().
The usb_serial_console_disconnect function is called from the
USB-serial-device disconnect callback when a device is going away. Hence
there is no need to check for the serial-device pointer being NULL.
The serial-device port pointers are stored in an array that is a member
of the serial struct so the address of the first member of the array
(which the array name decays to) is never NULL either.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 4a51096937 ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.
Make sure to initialise the new lock also for the fake tty to address
this regression.
Yes, this code is a mess, but cleaning it up is left for another day.
Fixes: 4a51096937 ("tty: Make tty_files_lock per-tty")
Cc: stable <stable@vger.kernel.org> # 4.6
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
No need to reinitialise the interrupt-in URB with values that have not
changed before (some) resubmissions.
This also allows the interrupt-in callback to have a single path for URB
resubmission.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant URB unlink as there's no need to unlink an URB which is
about to be killed synchronously.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Interface numbers do not change when enabling alternate settings as
comment and code in this driver suggested.
Remove the confusing comment and redundant retrieval of the interface
number in probe, while simplifying and renaming the interface-number
helper.
Fixes: 4db2299da2 ("sierra: driver interface blacklisting")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: 72fda3ca6f ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb6907 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design
change.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to check for short transfers before parsing the receive buffer
to avoid acting on stale data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure the received data has the required headers before parsing it.
Also drop the redundant urb-status check, which has already been handled
by the caller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to check for short transfers to avoid underflow in a loop
condition when parsing the receive buffer.
Also fix an off-by-one error in the incomplete sanity check which could
lead to invalid data being parsed.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # v2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port device rather than usb device in info and error messages.
This makes sure that driver and tty port is included in the messages,
while also making them more uniform.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant check of num_interrupt_in which has already been
verified in probe (killing a NULL-urb would also have been fine).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Return -ENODEV rather than -EINVAL on probe errors due to a missing
endpoint.
Also clean up the endpoint sanity check somewhat and use the interface
device for logging a more compact error in case an expected endpoint is
missing.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporation.
This is not a full-featured USB to serial converter, however it allows
basic communication and simple control which is enough for programming of
on-board flash and debugging through a debug monitor.
uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion
implemented in firmware.
This chip is also present in some debugging adaptors which use it for
USB-to-SPI conversion as well. The present driver doesn't cover SPI,
only USB-to-UART conversion is supported.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not report ASYNC_SKIP_TEST or ASYNC_AUTO_IRQ as being set in
TIOCGSERIAL handlers as these flags are not supported and do not really
make any sense for USB serial devices in the first place.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the ioctl handler and make sure to pass an unsigned-int rather
than serial_struct pointer to the TIOCSERGETLSR helper as this it what
the user argument really is.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6 ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com>
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Cc: stable@vger.kernel.org # v2.6.31: e3e574ad85
Signed-off-by: Johan Hovold <johan@kernel.org>
The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by
default boot with vid 0x413c and pid 0x81a3. When triggered QDL download
mode, the device switches to pid 0x81a6 and provides the standard TTY
used for firmware upgrade.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7a6ee2b027 ("USB: opticon: switch to generic read
implementation")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect and return an error on zero-length control-message
transfers when reading from the device.
This addresses a potential failure to detect an empty transmit buffer
during close.
Also remove a redundant check for short transfer when sending a command.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af954599 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d85 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
Fixes: e1ed212d85 ("USB: spcp8x5: add proper modem-status support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers when fetching
modem and line state in open and when retrieving registers.
This specifically makes sure that an errno is returned to user space on
errors in TIOCMGET instead of a zero bitmask.
Also drop the unused getdevice function which also lacked appropriate
error handling.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return an error on zero-length transfers when retrieving
the line settings even if the driver currently ignores the return value.
Also remove a redundant check for short transfer when setting the line
settings.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short transfers when reading a device register.
The modem-status handling had sufficient error checks in place, but move
handling of short transfers into the register accessor function itself
for consistency.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to log an error on short transfers when reading a device
register.
Also clear the provided buffer (which if often an uninitialised
automatic variable) on errors as the driver currently does not bother to
check for errors.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers so that errors are
logged when reading the modem status at open.
Note that while this also avoids initialising the modem status using
uninitialised heap data, these bits could not leak to user space as they
are currently not used.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove code that allocated but never used a buffer during open.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers and log an error
when reading incomplete manufacturer and boot descriptors.
Note that the default all-zero descriptors will now be used after a
short transfer is detected instead of partially initialised ones.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use a dedicated buffer for the DMA transfer and make sure to detect
short transfers to avoid parsing a corrupt descriptor.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short responses when reading the latency timer to
avoid using stale buffer data.
Note that no heap data would currently leak through sysfs as
ASYNC_LOW_LATENCY is set by default.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a4 ("USB: ark3116: Setup some basic infrastructure for
new ark3116 driver.")
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unused termios structure from private data that was left by an
earlier purge by commit b1cff285ae ("usb serial: Eliminate bogus ioctl
code").
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant packed attribute from the port-settings struct which is
already 1-byte aligned. Also replace __u8 with u8 for the field types as
this is not a structure we share with user space.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dead and broken code that only served as a reminder to one day
implement modem control.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace a couple of dev_info with dev_dbg and remove another.
Also use the port device for logging, and include a radix prefix when
logging the baudrate.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some CH340 devices appear unable to change the initial LCR settings, so
set a sane 8N1 default during probe to enable basic support for such
devices.
Also drop a redundant LCR read during device initialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Rename the line-control-register variable in set_termios to "lcr" and
use u8 type to match the shadow register.
Signed-off-by: Johan Hovold <johan@kernel.org>
Rename the shadow modem-status register currently named "line_status" to
the less confusing "msr".
Also rename the helper function used to parse the interrupt data.
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-status register was read as part of device configuration at
port_probe and then again at open (and reset-resume). During open (and
reset-resume) the MSR was read before submitting the interrupt URB,
something which could lead to an MSR-change going unnoticed when it
races with open (reset-resume).
Fix this by dropping the redundant reconfiguration of the port at every
open, and only read the MSR after the interrupt URB has been submitted.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
The variable havedata was only being set but never used afterwards.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.
Check for short transfers, and make sure to log any transfer errors.
Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).
Fixes: 6ce7610478 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf86 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96a9 ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]
Fixes: 619a6f1d14 ("USB: add usb-serial spcp8x5 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The write URB was being killed using the synchronous interface while
holding a spin lock in close().
Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 49cdee0ed0 ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB is killed at final port close since commit
0de9a7024e ("USB: overhaul of mos7840 driver").
Fixes: 0de9a7024e ("USB: overhaul of mos7840 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]
Note that we continue to treat the interrupt-in endpoint as optional for
now.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit b69578df7e ("USB: usbserial: mos7720: add support for
parallel port on moschip 7715"), the interrupt urb is no longer
submitted at first port open and the endpoint-address initialisation at
port-probe is no longer used.
Signed-off-by: Johan Hovold <johan@kernel.org>
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d ("USB: serial: add support for serial port on the
moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:
Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference at port open if a device lacks the expected
bulk in and out endpoints.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf071c20>] (mos7720_open [mos7720]) from [<bf0490e0>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0490e0>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf049d98>] (serial_open+0x48/0x6c [usbserial])
[<bf049d98>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in write() should the device lack the
expected interrupt-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000054
...
PC is at kobil_write+0x144/0x2a0 [kobil_sct]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for the expected endpoints in attach() and fail loudly if not
present.
Note that failing to do this appears to be benign since da280e3488
("USB: keyspan_pda: clean up write-urb busy handling") which prevents a
NULL-pointer dereference in write() by never marking a non-existent
write-urb as free.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # < v3.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference at open should the device lack a bulk-in or
bulk-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at iuu_open+0x78/0x59c [iuu_phoenix]
Fixes: 07c3b1a100 ("USB: remove broken usb-serial num_endpoints
check")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org>
Cancel the heartbeat work on driver unbind in order to avoid I/O after
disconnect in case the port is held open.
Note that the cancel in release() is still needed to stop the heartbeat
after late probe errors.
Fixes: 26c78daade ("USB: io_ti: Add heartbeat to keep idle EP/416
ports from disconnecting")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case a device is left in "boot-mode" we must not register any port
devices in order to avoid a NULL-pointer dereference on open due to
missing endpoints. This could be used by a malicious device to trigger
an OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf0caa84>] (edge_open [io_ti]) from [<bf0b0118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0b0118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf0b0da0>] (serial_open+0x48/0x6c [usbserial])
[<bf0b0da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should a
malicious device lack the expected endpoints when in download mode.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf011ed8>] (edge_open [io_ti]) from [<bf000118>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf000118>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf000da0>] (serial_open+0x48/0x6c [usbserial])
[<bf000da0>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when initialising URBs at open should a
non-EPIC device lack a bulk-in or interrupt-in endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000028
...
PC is at edge_open+0x24c/0x3e8 [io_edgeport]
Note that the EPIC-device probe path has the required sanity checks so
this makes those checks partially redundant.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to free the URB transfer buffer in case submission fails (e.g.
due to a disconnect).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference when clearing halt at open should the device
lack a bulk-out endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at cyberjack_open+0x40/0x9c [cyberjack]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
With gcc 4.1.2:
drivers/usb/serial/f81534.c: In function ‘f81534_port_probe’:
drivers/usb/serial/f81534.c:1250: warning: comparison is always false due to limited range of data type
f81534_logic_to_phy_port() may return a negative error value, which is
ignored by assigning it to u8 f81534_port_private.phy_num.
Use an intermediate variable of type int to fix this.
While at it, forward the actual error code instead of converting it to
-ENODEV, and drop the useless check for F81534_NUM_PORT, as the callee
always returns a valid port number in case of success.
Fixes: 0c9bd6004d ("USB: serial: add Fintek F81532/534 driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for PIDs 0x1040, 0x1041 of Telit LE922A.
Since the interface positions are the same than the ones used
for other Telit compositions, previous defined blacklists are used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=FChe
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.10-rc1
These updates include a new driver for Fintek F8153x devices, support
for the GPIO functionality on CP2105 devices, and improved support for
CH34X devices.
Included are also some clean ups and fixes for various minor issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Kill urbs and disable read before returning from open on failure to
retrieve the line state.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
On sparc32, tcflag_t is unsigned long, unlike all other architectures:
drivers/usb/serial/cp210x.c: In function 'cp210x_get_termios':
drivers/usb/serial/cp210x.c:717:3: warning: passing argument 2 of 'cp210x_get_termios_port' from incompatible pointer type
cp210x_get_termios_port(tty->driver_data,
^
drivers/usb/serial/cp210x.c:35:13: note: expected 'unsigned int *' but argument is of type 'tcflag_t *'
static void cp210x_get_termios_port(struct usb_serial_port *port,
^
Consistently use tcflag_t to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB
serial interface in its charging dock for the control pods, via which some
settings for the pods can be modified.
Signed-off-by: Paul Jakma <paul@jakma.org>
Cc: Barry Redmond <barry@brimbrothers.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop invalid user-pointer checks from ioctl handlers.
A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for the TI CC3200 LaunchPad board, which uses a
custom USB vendor ID and product ID. Channel A is used for JTAG, and
channel B is used for a UART.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Will probably be helpful if there are any more compatibility issues.
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
With the new reinitialization method, configuring parity, different
frame lengths and different stop bit settings should work as expected
on both CH340G and CH341A. Tested on a loopback-connected CH340G
with a logic analyzer in a number of different configurations.
Based on a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
Changing the LCR register after initialization does not seem to be reliable
on all chips (particularly not on CH341A). Restructure initialization and
configuration to always reinit the chip on configuration changes instead and
pass the LCR register value directly to the initialization command.
(Note that baud rates above 500kbaud are incorrect, but they're incorrect in
the same way both before and after this patch at least on the CH340G. Fixing
this isn't a priority as higher baud rates don't seem that reliable anyway.)
Cleaned-up version of a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
No functional changes, this just gives names to some registers and USB
requests based on Grigori Goronzy's work and WinChipTech's Linux driver
(which reassuringly agree), then uses them in place of magic numbers.
This also renames the misnamed BREAK2 register (actually UART config)
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for the GPIO found on the CP2105. Unlike the GPIO
provided by some of the other devices supported by the cp210x driver, the
GPIO on the CP2015 is muxed on pins otherwise used for serial control
lines. The GPIO have been configured in 2 separate banks as the choice to
configure the pins for GPIO is made separately for pins shared with each
of the 2 serial ports this device provides, though the choice is made for
all pins associated with that port in one go. The choice of whether to use
the pins for GPIO or serial is made by adding configuration to a one-time
programable PROM in the chip and can not be changed at runtime. The device
defaults to GPIO.
This device supports either push-pull or open-drain modes, it doesn't
provide an explicit input mode, though the state of the GPIO can be read
when used in open-drain mode. Like with pin use, the mode is configured in
the one-time programable PROM and can't be changed at runtime.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Return -EIO on short control transfers rather than -EPROTO which is used
for lower-level transfer errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e ("USB: serial: make minor allocation dynamic")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
The current tiocmget implementation would fail to report errors up the
stack and instead leaked a few bits from the stack as a mask of
modem-status flags.
Fixes: 39a66b8d22 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
More clean ups, including a second set of changes from Mathieu as part
of a major overhaul of the ti_usb_3410_5052 driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4c1M
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.9-rc1
More clean ups, including a second set of changes from Mathieu as part
of a major overhaul of the ti_usb_3410_5052 driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for Infineon flashloader 0x8087/0x0801.
The flashloader is used in Telit LE940B modem family with Telit
flashing application.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove variables affected but never read.
Also drop the now unused TI_SET_SERIAL_FLAGS define.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: drop TI_SET_SERIAL_FLAGS ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Use C_X tty.h macros to avoid direct manipulation of termios
c_cflag variable.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
It is useless to check the return of usb_get_serial_port_data in the tty
and tty-port callbacks.
No need to check interface private data in close() either.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
__uX types should only be used for user-space interactions.
Also clean up uart-config endianess handling, and drop some redundant
casts.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
There is an allocation with GFP_KERNEL flag in mos7840_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There is an allocation with GFP_KERNEL flag in mos7720_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
