In order to display console messages in low power mode, console pins
must be kept active after suspend call.
Initial patch "serial: stm32: add support for no_console_suspend" was part
of "STM32 usart power improvement" series, but as dependancy to
console_suspend pinctl state has been removed to fit with Rob comment [1],
this patch has no more dependancy with any other patch of this series.
[1] https://lkml.org/lkml/2019/7/9/451
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200519094104.27082-1-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable kgdb to debug the early parts of the kernel.
Unfortunately kgdb normally is a client of the tty API in the kernel
and serial drivers don't register to the tty layer until fairly late
in the boot process.
Serial drivers do, however, commonly register a boot console. Let's
enable the kgdboc driver to work with boot consoles to provide early
debugging.
This change co-opts the existing read() function pointer that's part
of "struct console". It's assumed that if a boot console (with the
flag CON_BOOT) has implemented read() that both the read() and write()
function are polling functions. That means they work without
interrupts and read() will return immediately (with 0 bytes read) if
there's nothing to read. This should be a safe assumption since it
appears that no current boot consoles implement read() right now and
there seems no reason to do so unless they wanted to support
"kgdboc_earlycon".
The normal/expected way to make all this work is to use
"kgdboc_earlycon" and "kgdboc" together. You should point them both
to the same physical serial connection. At boot time, as the system
transitions from the boot console to the normal console (and registers
a tty), kgdb will switch over.
One awkward part of all this, though, is that there can be a window
where the boot console goes away and we can't quite transtion over to
the main kgdboc that uses the tty layer. There are two main problems:
1. The act of registering the tty doesn't cause any call into kgdboc
so there is a window of time when the tty is there but kgdboc's
init code hasn't been called so we can't transition to it.
2. On some serial drivers the normal console inits (and replaces the
boot console) quite early in the system. Presumably these drivers
were coded up before earlycon worked as well as it does today and
probably they don't need to do this anymore, but it causes us
problems nontheless.
Problem #1 is not too big of a deal somewhat due to the luck of probe
ordering. kgdboc is last in the tty/serial/Makefile so its probe gets
right after all other tty devices. It's not fun to rely on this, but
it does work for the most part.
Problem #2 is a big deal, but only for some serial drivers. Other
serial drivers end up registering the console (which gets rid of the
boot console) and tty at nearly the same time.
The way we'll deal with the window when the system has stopped using
the boot console and the time when we're setup using the tty is to
keep using the boot console. This may sound surprising, but it has
been found to work well in practice. If it doesn't work, it shouldn't
be too hard for a given serial driver to make it keep working.
Specifically, it's expected that the read()/write() function provided
in the boot console should be the same (or nearly the same) as the
normal kgdb polling functions. That means continuing to use them
should work just fine. To make things even more likely to work work
we'll also trap the recently added exit() function in the boot console
we're using and delay any calls to it until we're all done with the
boot console.
NOTE: there could be ways to use all this in weird / unexpected ways.
If you do something like this, it's a bit of a buyer beware situation.
Specifically:
- If you specify only "kgdboc_earlycon" but not "kgdboc" then
(depending on your serial driver) things will probably work OK, but
you'll get a warning printed the first time you use kgdb after the
boot console is gone. You'd only be able to do this, of course, if
the serial driver you're running atop provided an early boot console.
- If your "kgdboc_earlycon" and "kgdboc" devices are not the same
device things should work OK, but it'll be your job to switch over
which device you're monitoring (including figuring out how to switch
over gdb in-flight if you're using it).
When trying to enable "kgdboc_earlycon" it should be noted that the
names that are registered through the boot console layer and the tty
layer are not the same for the same port. For example when debugging
on one board I'd need to pass "kgdboc_earlycon=qcom_geni
kgdboc=ttyMSM0" to enable things properly. Since digging up the boot
console name is a pain and there will rarely be more than one boot
console enabled, you can provide the "kgdboc_earlycon" parameter
without specifying the name of the boot console. In this case we'll
just pick the first boot that implements read() that we find.
This new "kgdboc_earlycon" parameter should be contrasted to the
existing "ekgdboc" parameter. While both provide a way to debug very
early, the usage and mechanisms are quite different. Specifically
"kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and
there is a transition from one to the other. The "ekgdboc" parameter,
on the other hand, replaces the "kgdboc" parameter. It runs the same
logic as the "kgdboc" parameter but just relies on your TTY driver
being present super early. The only known usage of the old "ekgdboc"
parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should
be noted that "kbd" has special treatment allowing it to init early as
a tty device.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This file is only ever compiled if that config is on since the
Makefile says:
obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
Let's get rid of the useless #ifdef.
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.7.Icb528f03d0026d957e60f537aa711ada6fd219dc@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This reverts commit 81eaadcae8.
Commit 81eaadcae8 ("kgdboc: disable the console lock when in kgdb")
is no longer needed now that we have the patch ("kgdb: Disable
WARN_CONSOLE_UNLOCKED for all kgdb"). Revert it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.2.I02258eee1497e55bcbe8dc477de90369c7c7c2c5@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace contents of EXAR_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512140252.67631-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXrVmRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymY+ACfelBeBAxlYjuvZ8QpDYSkR9fl8EIAoKeuJocX
TaXtUFCvCSax68siL81w
=L0Rp
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues"
* tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xilinx_uartps: Fix missing id assignment to the console
vt: fix unicode console freeing with a common interface
Revert "tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart"
Support 32-bit access for the TX/RX hold registers UTXH and URXH.
This is required for some newer SoCs.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-3-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the name of macro for general usage.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-1-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9231e698
Rajendra writes:
Greg, there are other patches in the series which have a
dependency on this patch [1] would it be possible for you to
drop this patch and instead ack it so it can be taken via the
msm tree?
So dropping it from here.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1588507469-31889-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 580d952e44 ("tty:
serial: bcm63xx: fix missing clk_put() in bcm63xx_uart") because we
should not be doing a clk_put() if we were not successful in getting a
valid clock reference via clk_get() in the first place.
Fixes: 580d952e44 ("tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200501013904.1394-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains a handful of fixes that I'd like to target for 5.7.
Specifically:
* The change of a linker argument to allow linking with lld.
* A build fix for configurations without a frame pointer.
* A handful of build fixes related the SBI 0.1 vs 0.2 split.
* The removal of STRICT_KERNEL_RWX for !MMU, which isn't useful
-----BEGIN PGP SIGNATURE-----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=MtxP
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes.
Specifically:
- fix linker argument to allow linking with lld
- build fix for configurations without a frame pointer
- a handful of build fixes related the SBI 0.1 vs 0.2 split
- remove STRICT_KERNEL_RWX for !MMU, which isn't useful"
* tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: select ARCH_HAS_STRICT_KERNEL_RWX only if MMU
riscv: sbi: Fix undefined reference to sbi_shutdown
tty: riscv: Using RISCV_SBI_V01 instead of RISCV_SBI
riscv: sbi: Correct sbi_shutdown() and sbi_clear_ipi() export
riscv: fix vdso build with lld
RISC-V: stacktrace: Declare sp_in_global outside ifdef
Currently the following messages are seen when booting i.MX8QXP:
fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)
It is not really useful to have such messages on every boot, so change
them to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below error reported by coccicheck
drivers/tty/serial/bcm63xx_uart.c:848:2-8: ERROR: missing clk_put;
clk_get on line 842 and execution via conditional on line 846
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587472306-105155-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
breaks the UART on Cubieboard7-lite (based on S700 SoC), This is due to the
fact that generic clk routine clk_disable_unused() disables the gate clks,
and that in turns disables OWL UART (but UART driver never enables it). To
prove this theory, Andre suggested to use "clk_ignore_unused" in kernel
commnd line and it worked (Kernel happily lands into RAMFS world :)).
This commit fix this up by adding clk_prepare_enable().
Fixes: 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587067917-1400-1-git-send-email-amittomer25@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As shown in SBI v0.2, the legacy console SBI functions (sbi_console_getchar()
and sbi_console_putchar()) are expected to be deprecated; they have no replacement.
Let's HVC_RISCV_SBI and SERIAL_EARLYCON_RISCV_SBI depends on RISCV_SBI_V01.
Fixes: efca139892 ("RISC-V: Introduce a new config for SBI v0.1")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Sparc HV console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Link: https://lore.kernel.org/r/20200402172026.79478-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of accessing the registers and checking for tx_empty,
use cdns_uart_tx_empty in cdns_uart_console_write function.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-3-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci.h file includes the legacy <linux/gpio.h> header
but the driver is actually migrated to use the mctrl_gpio
library so this is not needed.
Cc: George G. Davis <george_davis@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200415180250.221762-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable i is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed. Also rename i to ret as this new
name makes makes more sense.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200405135423.383466-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the following:
var_compare_op: Comparing chan to null implies that chan might be null.
1234 if (chan)
1235 dmaengine_terminate_all(chan);
1236
Dereference after null check (FORWARD_NULL)
var_deref_op: Dereferencing null pointer chan.
1237 dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
Technically, this is correct. But lpuart_dma_rx_free() is guarded by
lpuart_dma_rx_use which is only true if there is a dma channel, see
lpuart_rx_dma_startup(). In any way, this looks bogus. So remove
the superfluous "if (chan)" check and make coverity happy.
Fixes: a092ab25fd ("tty: serial: fsl_lpuart: fix DMA mapping")
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200403174942.9594-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the OMAP serial driver to use a GPIO descriptor
for the optional RTS signal.
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415183927.269445-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver includes <linux/gpio.h> but does not use any symbols
from the file so drop this include.
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415184300.269889-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Commit 7f9803072f ("serial: 8250: Support console on software emulated
rs485 ports") amended serial8250_console_write() with rs485 support, but
positioned the invocation of ->rs485_stop_tx() after re-enablement of
interrupts. The irq handler and ->console_write() are serialized with
the port spinlock, so no problem there, but due to the rs485 delay, the
irq handler may unnecessarily spin for a while. Avoid that by moving
->rs485_stop_tx() before re-enablement of interrupts, which also mirrors
the order at the beginning of serial8250_console_write().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/019839cb1f61b01210b6ff9ac9f9079ca77f8411.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a silly copy-paste mistake, commit 7f9803072f ("serial: 8250:
Support console on software emulated rs485 ports") erroneously pauses
for the duration of delay_rts_before_send after writing to the console,
instead of delay_rts_after_send. Mea culpa.
Fixes: 7f9803072f ("serial: 8250: Support console on software emulated rs485 ports")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9dd67f33c90d23f7fafa3b81b1e812ddabf9ca24.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-test reported an error:
config: mips-randconfig-a001-20200321 ...
>> drivers/tty/serial/sprd_serial.c:1175: undefined reference
to `clk_set_parent'
Because some mips Kconfig selects HAVE_CLK but not COMMON_CLK and no
clk_set_parent implemented, so the error was exposed. So adding
dependence on COMMON_CLK can fix this issue.
Fixes: 7ba87cfec7 ("tty: serial: make SERIAL_SPRD not depend on ARCH_SPRD")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200325081427.20312-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of lpuart_dma_tx_request() is an negative errno on
failure and zero on success.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move dma_request_chan() out of the atomic context. First this call
should not be in the atomic context at all and second the
dev_info_once() may cause a hang because because the console takes this
spinlock, too.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for omap-serial
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321204031.30369-1-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART on K3 SoCs has configurable RX timeout behavior (controlled via
EFR2) and better DMA integration. This allows to transfer as larger
amount data per DMA transfer compared to older SoCs. Add support for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-7-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per Advisory 27 of AM437x Silicon errata document, Spurious UART
interrupts may occur when DMA mode (FCR.DMA_MODE) is enabled. The
Interrupt Controller flags that a UART interrupt has occurred; however,
the associated IT_PENDING bit remains set to 1, indicating that no
interrupt is pending. Acknowledge the spurious interrupts for every
occurrence as workaround.
Errata is applicable to all TI SoCs with this IP.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-6-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although same 8250 compliant UART IP is reused across different SoC,
their integration wrt DMA varies greatly across SoCs. Therefore,
different SoC may need to use different FIFO trigger level for DMA
event and DMA configuration parameters. Provide a way to pass this
information via driver data. This is required to support UART DMA on
AM654/J721e SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-5-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Caller functions of __dma_rx_do_complete() already hold rx_dma_lock.
Therefore move locking out of the function to avoid need to release and
reacquire lock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-4-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account data stuck in DMA internal buffers before pushing data
to higher layer. dma_tx_state has "in_flight_bytes" member that provides
this information.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call stop_rx() to halt reception when throttle is requested. Update
unthrottle callback to restart reception.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that all bytes are transmitted out of Uart by monitoring
CDNS_UART_SR_TACTIVE bit as well.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/e2514818af5973be291cc117d07739f068b71639.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termios function should not wait for the transmit FIFO empty
(CDNS_UART_SR_TXEMPTY) unconditionally. The tty layer takes care
of it based on the parameter passed (TCSANOW/TCSADRAIN/TCSAFLUSH).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/536e190dd5bbb474007a67e6323c048288942a28.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092930.24433-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to cleanup sprd_port anymore, since we've dropped the way
of using the sprd_port[] array to get port index.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the process of getting serial port number, with
this patch, serial devices must have aliases configured in devicetree.
The serial port searched out via sprd_port array maybe wrong if we don't
have serial alias defined in devicetree, and specify console with command
line, we would get the wrong port number if other serial ports probe
failed before console's. So using aliases is mandatory.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It would be too tricky and error prone to allow DMA operations on
kernel console.
One of the concern is when DMA is a separate device, for example on
Intel CherryTrail platforms, and might need special work around to be
functional, see the commit
eebb3e8d8a ("ACPI / LPSS: override power state for LPSS DMA device")
for more information.
Another one is that kernel console is used in atomic context, e.g.
when printing crucial information to the user (Oops or crash),
and DMA may not serve due to power management complications
including non-atomic ACPI calls but not limited to it (see above).
Besides that, other concerns are described in the commit
84b40e3b57 ("serial: 8250: omap: Disable DMA for console UART")
done for OMAP UART and may be repeated here.
Disable any kind of DMA operations on kernel console due to above concerns.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing any kind of power management for kernel console is really bad idea.
First of all, it runs in poll and atomic mode. This fact attaches a limitation
on the functions that might be called. For example, pm_runtime_get_sync() might
sleep and thus can't be used. This call needs, for example, to bring the device
to powered on state on the system, where the power on sequence may require
on-atomic operations, such as Intel Cherrytrail with ACPI enumerated UARTs.
That said, on ACPI enabled platforms it might even call firmware for a job.
On the other hand pm_runtime_get() doesn't guarantee that device will become
powered on fast enough.
Besides that, imagine the case when console is about to print a kernel Oops and
it's powered off. In such an emergency case calling the complex functions is
not the best what we can do, taking into consideration that user wants to see
at least something of the last kernel word before it passes away.
Here we modify the 8250 console code to prevent runtime power management.
Note, there is a behaviour change for OMAP boards. It will require to detach
kernel console to become idle.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future we would like to disable power management on the serial devices
used as kernel consoles to avoid weird behaviour in some cases. However,
disabling PM may prevent system to go to deep sleep states, which in its turn
leads to the higher power consumption.
Tony Lindgren proposed a work around, i.e. allow user to detach such consoles
to make PM working again. In case user wants to see what's going on, it also
provides a mechanism to attach console back.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 175b558d0e.
When the user configures a kernel without support for Samsung SoCs, it
makes no sense to ask the user about enabling "Samsung SoC serial
support", as Samsung serial ports can only be found on Samsung SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200306102301.16870-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes: f4487db58e ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function sprd_console_setup() would be called from .probe() which can
be called after freeing __init functions, for example the .probe() would
return -EPROBE_DEFER since it depends on clock modules.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, the purpose is to
keep the console port alive as possible even if there's some error
caused by no clock configured under serial devicetree nodes. But with
the patch [1], the console port couldn't be identified if missing
console command line.
So this patch adds using another interface to do check by reading
stdout-path.
[1] https://lore.kernel.org/lkml/20190826072929.7696-4-zhang.lyra@gmail.com/
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The geni serial driver's shutdown code had a special case to call
console_stop(). Grepping through the code, it was the only serial
driver doing something like this (the only other caller of
console_stop() was in serial_core.c).
As far as I can tell there's no reason to call console_stop() in the
geni code. ...and a good reason _not_ to call it. Specifically if
you have an agetty running on the same serial port as the console then
killing the agetty kills your console and if you start the agetty
again the console doesn't come back.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.2.I3648fac6c98b887742934146ac2729ecb7232eb1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a board using qcom_geni_serial I found that I could no longer
interact with kdb if I got a crash after the "agetty" running on the
same serial port was killed. This meant that various classes of
crashes that happened at reboot time were undebuggable.
Reading through the code, I couldn't figure out why qcom_geni_serial
felt the need to run so much code at port shutdown time. All we need
to do is disable the interrupt.
After I make this change then a hardcoded kgdb_breakpoint in some late
shutdown code now allows me to interact with the debugger. I also
could freely close / re-open the port without problems.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.1.Icf54c533065306b02b880c46dfd401d8db34e213@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'source' (include) all of the tty/*/Kconfig files from
drivers/tty/Kconfig instead of from drivers/char/Kconfig.
This consolidates them both in source code and in menu
presentation to the user.
Move hvc/Kconfig and serial/Kconfig 'source' lines into the
if TTY/endif block and remove the if TTY/endif blocks from
those 2 files.
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Jiri Slaby <jslaby@suse.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200311225736.32147-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor uart_unlock_and_check_sysrq() to:
- explicitly show that we release a port lock which makes
static analyzers happy:
CHECK drivers/tty/serial/serial_core.c
.../serial_core.c:3290:17: warning: context imbalance in 'uart_unlock_and_check_sysrq' - unexpected unlock
- use flags instead of irqflags to avoid confusion with IRQ flags
- provide one return point
- be more compact
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200310174337.74109-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in SysRq code instead of open coded variant.
This eliminates the conditional entirely for SERIAL_CORE_CONSOLE=n case.
While here, refactor the conditional to be more compact.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useful to see on the serial console the magic sequence itself
to enable SysRq without rummaging source code.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiler is not happy about using ARRAY_SIZE() in comparison to smaller type:
CC drivers/tty/serial/serial_core.o
.../serial_core.c: In function ‘uart_try_toggle_sysrq’:
.../serial_core.c:3222:24: warning: comparison is always false due to limited range of data type [-Wtype-limits]
3222 | if (++port->sysrq_seq < (ARRAY_SIZE(sysrq_toggle_seq) - 1)) {
| ^
Looking at the code it appears that there is an additional weirdness,
i.e. use ARRAY_SIZE() against simple string literal. Yes, the idea probably
was to allow '\0' in the sequence, but it's impractical: kernel configuration
won't accept it to begin with followed by a comment about '\0' before
comparison in question.
Drop all these by switching to strlen() and convert code accordingly.
Note, GCC seems clever enough to calculate string length at compile time.
Fixes: 68af43173d ("serial/sysrq: Add MAGIC_SYSRQ_SERIAL_SEQUENCE")
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix the RX cancel command failure, rx_fifo buffer needs to be
flushed in stop_rx() by calling handle_rx().In handle_rx() the data
in rx_fifo buffer is read and then dropped, not sent to upper layers.
If set_termios is called before startup, by this time memory is not
allocated to port->rx_fifo buffer, which leads to a NULL pointer
dereference.
To avoid this NULL pointer dereference allocate memory to port->rx_fifo
in probe itself.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reported-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1583477228-32231-2-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver for the Intel MID never seems to have been properly
integrated upstream: the platform data in <linux/spi/ifx_modem.h>
is not used anywhere in the kernel and haven't been since it was
merged into the kernel in 2010.
There might be out-of-tree users, so I don't want to delete the
driver, but I will refactor it to use GPIO descriptors, which
means that out-of-tree users will need to adapt.
There are several examples in the kernel of how to provide the
resources necessary for using GPIO descriptors to pass in the
GPIO lines, for the MID platform in particular, it will suffice
to inspect the code in files like:
arch/x86/platform/intel-mid/device_libs/platform_bt.c
This refactoring transfers all GPIOs in the driver, including
a hard-coded "PMU reset" in the driver to use GPIO descriptors
instead.
The following named GPIO descriptors need to be supplied:
- reset
- power
- mrdy
- srdy
- rst_out
- pmu_reset
Cc: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311083131.693908-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The &spi->dev is used so many times that the code gets
visibly better by introducing a simple dev helper variable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200311083131.693908-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a early_console_setup() for the LS1028A SoC with 32bit, little
endian access. If the bootloader does a fixup of the clock-frequency
node the baudrate divisor register will automatically be set.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-5-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LS1028A uses little endian register access and has a different FIFO
size encoding.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.
The error messages look like:
[ 19.012140] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
[ 19.023593] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
This was tested on a custom board with a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA channel might not be available at probe time. This is esp. the
case if the DMA controller has an IOMMU mapping.
There is also another caveat. If there is no DMA controller at all,
dma_request_chan() will also return -EPROBE_DEFER. Thus we cannot test
for -EPROBE_DEFER in probe(). Otherwise the lpuart driver will fail to
probe if, for example, the DMA driver is not enabled in the kernel
configuration.
To workaround this, we request the DMA channel in _startup(). Other
serial drivers do it the same way.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_ATMEL_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200310133057.86840-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_PIC32_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311090027.64441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the vt fixes in here and it resolves a merge issue with
drivers/tty/vt/selection.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a61 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
As a measure of balance between on and off options, add
MAGIC_SYSRQ_SERIAL_SEQUENCE which is a string sequence that can enable
sysrq if it follows BREAK on a serial line. The longer the string - the
less likely it may be in the garbage.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
Based-on-patch-by: Vasiliy Khoruzhick <vasilykh@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-3-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal if data
is transmitted through the tty layer.
Console messages bypass the tty layer and instead are emitted via
serial8250_console_write(). Amend that function to drive RTS as well,
allowing for a console on rs485 ports.
Note that serial8250_console_write() may be called concurrently to the
tty layer accessing the port. The two protect their accesses with the
port lock, but serial8250_console_write() may find RTS still being
asserted by the tty layer, in which case it shouldn't be deasserted
after the console message has been printed. Recognize such situations
by checking the em485->tx_stopped flag.
If a delay_rts_before_send or delay_rts_after_send has been specified,
serial8250_console_write() busy-waits for its duration. Optimizations
for those wait times are conceivable: E.g. if RTS is already asserted,
we could check whether em485->start_tx_timer is active and wait only
for the remaining expire time. But this would require calling into
the hrtimer infrastructure, which involves acquiring locks and
potentially reprogramming timer hardware. Such operations seem too
risky in the context of console printout, which needs to work even when
the kernel has crashed and emits a BUG splat. So I've gone with a
simplistic solution which just always waits for the full delay.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/65edffce4670a19e598015c03cbe46f1ffd93e43.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend 8250_bcm2835aux.c to support rs485 as introduced for 8250_omap.c
by commit e490c9144c ("tty: Add software emulated RS485 support for
8250").
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register: If the bit is clear, RTS is high. With omap, it's
apparently the other way round.
Moreover, omap achieves half-duplex mode by disabling the UART_IER_RDI
interrupt and clearing the RX FIFO when TX stops. This approach doesn't
work on bcm2835aux because the UART_LSR_DR bit is set even when
UART_IER_RDI is disabled. Consequently, serial8250_handle_irq() invokes
serial8250_rx_chars() to empty the FIFO and characters are received even
though the user requested half-duplex. Solve by disabling the receiver
using the non-standard CNTL register.
Cache that register in the driver's private data for performance. Set
the private data pointer before calling serial8250_register_8250_port()
to prevent a null pointer deref in case one of the rs485 callbacks is
invoked immediately after port registration.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/dd86460e20a8f979b7272a0bde73640312b902b1.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far the only drivers taking advantage of it are 8250_omap.c and
8250_of.c.
We're about to make use of the feature in 8250_bcm2835aux.c as well.
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register. Moreover, omap achieves half-duplex mode by
disabling the RX interrupt and clearing the RX FIFO when TX stops.
The bcm2835aux requires disabling the receiver instead.
Support these behavioral differences by generalizing the rs485 emulation:
Introduce ->rs485_start_tx() and ->rs485_stop_tx() callbacks in struct
uart_8250_port, provide generic implementations containing the existing
code and use them as callbacks in 8250_omap.c and 8250_of.c.
start_tx_rs485() is idempotent in that it recognizes whether RTS is
already asserted. Achieve the same by introducing a tx_stopped flag in
struct uart_8250_em485. This may even perform a little better on arches
where memory access is faster than mmio access.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/5ac0464ae4414708e723a1e0d52b0c1b2bd41b9b.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When rs485 transmission over an 8250 port stops, __stop_tx() assigns
active_timer = NULL before calling __stop_tx_rs485().
That function in turn either assigns active_timer = stop_tx_timer and
rearms the timer (in case a delay_rts_after_send needs to be observed)
or directly calls __do_stop_tx_rs485().
Move the assignment active_timer = NULL to __stop_tx_rs485() into the
branch which directly calls __do_stop_tx_rs485(), thereby avoiding a
duplicate assignment and simplifying the code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/bca638405550eaf92f0c6060b553b687f35885e0.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the generic ->rs485_config() callback to sanitize RTS polarity and
zero-fill the padding (in addition to the existing sanitization of the
RTS delays).
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/ff833721bc372d38678f289eb2a44dbf016d5203.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
Drivers opt in to the feature by calling serial8250_em485_init() from
their ->rs485_config() callback.
So far there are two drivers doing that, 8250_omap.c and 8250_of.c.
Both use an identical callback. We're about to add a third user of that
callback, therefore deduplicate it and move it to 8250_port.c.
Drivers now opt in to rs485 software emulation by assigning the generic
serial8250_rs485_config() callback introduced herein to their
.rs485_config struct member. This change allows unexporting
serial8250_em485_init() and declaring it static.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/fcef63642dc4eae41ae7842d23747b2bf5d40285.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of 8250 ports in
case they are attached to an rs485 transceiver.
If the property "linux,rs485-enabled-at-boot-time" is present, invoke
the ->rs485_config() callback to immediately deassert RTS, thereby
ceasing control of the bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5908ea89b7f9da54872d6634b606d83db032297a.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_mctrl() currently allows modifying the RTS modem
control line even when RTS is used as an rs485 Transmit Enable signal.
It is thus possible for user space to interfere with rs485 communication
by invoking a TIOCMSET ioctl().
Ignore such change requests and retain the current RTS polarity when in
rs485 mode. Note that serial8250_set_mctrl() is always called with
port->lock held, so there's no risk that RTS is changed concurrently.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/b1ce34ca9bc4d7bdc6e9852fcf30b1f4e37c8a80.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a driver exposes early consoles with EARLYCON_DECLARE() and
OF_EARLYCON_DECLARE(), pefer the non-OF variant if the user specifies it
by
earlycon=<driver>,<options>
The rationale behind this is that some drivers register multiple setup
functions under the same driver name. Eg.
OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
It depends on the order of the entries which console_setup() actually
gets called. To make things worse, I guess it also depends on the
compiler how these are ordered. Thus always prefer the EARLYCON_DECLARE()
ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200220174607.24285-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to tty serial drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301204517.GA10368@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node
dependence") the port line number can also be allocated by IDA, but in
case of an error the ID will no be removed again. More importantly, any
ID will be freed in remove(), even if it wasn't allocated but instead
fetched by of_alias_get_id(). If it was not allocated by IDA there will
be a warning:
WARN(1, "ida_free called for id=%d which is not allocated.\n", id);
Move the ID allocation more to the end of the probe() so that we still
can use plain return in the first error cases.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200303174306.6015-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a659652f61.
This broke the earlycon on LS1021A processors because the order of the
earlycon_setup() functions were changed. Before the commit the normal
lpuart32_early_console_setup() was called. After the commit the
lpuart32_imx_early_console_setup() is called instead.
Fixes: a659652f61 ("tty: serial: fsl_lpuart: drop EARLYCON_DECLARE")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200303174306.6015-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the dependency with ARCH_SPRD from sprd serial/console Kconfig-s,
since we want them can be built-in when ARCH_SPRD is set as 'm'.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200305103228.9686-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->setup() callback is mandatory for the devices.
Provide it for Elkhart Lake UART ports.
Note, for time being it's empty, but in the future it might require
an additional configuration such as DMA.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200305130822.36850-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MTK uart design no need to control uart clock,
so we just control bus clock in runtime function.
Add uart clock used count to avoid repeatedly switching the clock.
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Link: https://lore.kernel.org/r/1582707225-26815-1-git-send-email-changqi.hu@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The peripheral has support for inverting its input and/or output
signals. This is useful if the hardware flips polarity of the
peripheral's signal, such as swapped +/- pins on an RS-422 transceiver,
or an inverting level shifter. Add support for these control registers
via the device tree binding.
As part of this change, make the writes of the various registers more
uniform by moving the UCR3 block up near the other registers' blocks,
since the INVT bit must be set before enabling the peripheral.
Signed-off-by: George Hilliard <ghilliard@kopismobile.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200226222319.18383-3-ghilliard@kopismobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulate half-duplex operation and use mctrl_gpio to add support for
RS485 tranceiver with transmit/receive switch hooked to RTS GPIO line.
This is needed to make use of the RS485 port found on Teltonika RUT955.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200221212331.GA21467@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPM UART (PowerPC) has an open coded GPIO modem control
handling. Since I can't test this I can't just migrate it to
the serial mctrl GPIO helper library though I wish I could.
I do second best and convert it to GPIO descriptors at least.
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229231842.247563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from <linux/gpio.h>
so drop this include.
Cc: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Cc: Songjun Wu <songjun.wu@linux.intel.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229212331.174946-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from these GPIO
includes so drop them. These are probably just historical
artifacts from befor mctrl_gpio was used.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200229220941.205599-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in this place, the function should return a
negative value and the PTR_ERR already returns
a negative,so return -PTR_ERR() is wrong.
Signed-off-by: tangbin <tangbin@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200305013823.20976-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert pr_*() calls to dev_*() ones. We have a port, we should use it.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move device attributes to DEVICE_ATTR_RW() as that would make things
a lot more "obvious" what is happening here.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're unlucky enough that this drivers binds to a mrvl,mmp-uart device
on a MMP3, the port type gets detected as 16550A instead of XScale, and it
won't work. Other drivers that may bind to the same hardware are 8250_of
and, god forbid, serial_pxa.
Force the port type, we know it's a PORT_XSCALE.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200219080130.4334-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move device attributes to DEVICE_ATTR_RO() as that would make things
a lot more "obvious" what is happening here.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symbolic permissions 'S_IRUSR | S_IRGRP' are not preferred.
Use octal permissions '0440'. This also makes code shorter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200214114339.53897-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two times duplicated excerpt where we initialize spin lock
for UART port. Consolidate it under uart_port_spin_lock_init() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200214114339.53897-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce uart_console_enabled() helper which checks port to be console
and console is registered in the list.
Note, this helper will be used in the future as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200214114339.53897-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Christophe reports that powerpc 8xx silently fails to 5.6-rc1. It turns
out I was wrong about nobody relying on the lazy initialization of the
cpm/qe muram in commit b6231ea2b3 (soc: fsl: qe: drop broken lazy
call of cpm_muram_init()).
Rather than reinstating the somewhat dubious lazy call (initializing a
currently held spinlock, and implicitly doing a GFP_KERNEL under that
spinlock), make sure that cpm_muram_init() is called early enough - I
thought the calls from the subsys_initcalls were good enough, but when
used by console drivers, that's obviously not the
case. cpm_muram_init() is safe to call twice (there's an early return
if it is already initialized), so keep the call from cpm_init() - in
case SERIAL_CPM_CONSOLE=n.
Fixes: b6231ea2b3 (soc: fsl: qe: drop broken lazy call of cpm_muram_init())
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200213114342.21712-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200213004426.GA7886@embeddedor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200213004611.GA8748@embeddedor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, rename PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE to
PM_QOS_CPU_LATENCY_DEFAULT_VALUE and update all of the code
referring to it accordingly.
Next, rename cpu_dma_constraints to cpu_latency_constraints, move
the definition of it closer to the functions referring to it and
update all of them accordingly. [While at it, add a comment to mark
the start of the code related to the CPU latency QoS.]
Finally, rename the pm_qos_power_*() family of functions and
pm_qos_power_fops to cpu_latency_qos_*() and cpu_latency_qos_fops,
respectively, and update the definition of cpu_latency_qos_miscdev.
[While at it, update the miscdev interface code start comment.]
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200212193700.GA29715@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX cancel command fails when BT is switched on and off multiple times.
To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register
instead of SE_GENI_S_CMD_CTRL_REG.
As per the HPG update, handle the RX last bit after cancel command
and flush out the RX FIFO buffer.
Signed-off-by: satya priya <skakit@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 54e53b2e80
("tty: serial: 8250: pass IRQ shared flag to UART ports")
nicely explained the problem:
---8<---8<---
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling routines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
---8<---8<---
But unfortunately didn't fix the root cause. Let's try again here by moving
IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup().
This should fix the similar issue reported for 8250_pnp case.
Since this change we don't need to have custom solutions in 8250_aspeed_vuart
and 8250_of drivers, thus, drop them.
Fixes: 1c2f04937b ("serial: 8250: add IRQ trigger support")
Reported-by: Li RongQing <lirongqing@baidu.com>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define the OF early console for BCM2835 aux UART, which can be enabled
by passing "earlycon" on the boot command line. This UART is found on
BCM283x and BCM27xx SoCs, a.k.a. Raspberry Pi in its variants.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Link: https://lore.kernel.org/r/20200126123314.3558-1-matthias.bgg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support booting NVIDIA Tegra platforms with either Device-Tree or
ACPI, create a Tegra specific 8250 serial driver that supports both
firmware types. Another benefit from doing this, is that the Tegra
specific codec in the generic Open Firmware 8250 driver can now be
removed.
Signed-off-by: Jeff Brasen <jbrasen@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200129132817.26343-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open coded single-linked list iteration loop with for_each_console()
helper in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200124161132.65519-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible to get an instant RX timeout or end-of-transfer interrupt
before RX DMA was started, if transaction is less than 16 bytes. Transfer
should be handled in PIO mode in this case because DMA can't handle it.
This patch brings back the original behaviour of the driver that was
changed by accident by a previous commit, it fixes occasional Bluetooth HW
initialization failures which I started to notice recently.
Fixes: d5e3fadb70 ("tty: serial: tegra: Activate RX DMA transfer by request")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200209164415.9632-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.
Fixes: 98f2082c3a ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8e ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd27 ("Merge
tag 'ioremap-5.6' of git://../ioremap").
Apparently this didn't get any build testing anywhere. Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.
I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
- Support mremap() for the VDSO, primarily to allow CRIU to restore the
VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement of
the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs by
running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to
take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXjRnpxYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdNYoA/3ZhgKX1L/hwvkPKwu7FxbL41pjB
WAm8IYDaxPvgxkcSAP9FNNepHK+oBPM8I2e3DvDvmcuYjumztdikzYbJ5HuMBA==
=MV2S
-----END PGP SIGNATURE-----
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
The main irq handler function starts by first masking disabled
interrupts in the status register values to ensure to only handle
enabled interrupts. This is important as when the RX path in the
hardware is disabled reading the RX fifo results in an external abort.
This checking must be done under the port lock, otherwise the following
can happen:
CPU1 | CPU2
|
irq triggers as there are chars |
in the RX fifo |
| grab port lock
imx_uart_int finds RRDY enabled |
and calls imx_uart_rxint which |
has to wait for port lock |
| disable RX (e.g. because we're
| using RS485 with !RX_DURING_TX)
|
| release port lock
read from RX fifo with RX |
disabled => exception |
So take the port lock only once in imx_uart_int() instead of in the
functions called from there.
Reported-by: Andre Renaud <arenaud@designa-electronics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the driver private data of the BCM2835 auxiliary UART so that
upcoming commits may add further members with proper kerneldoc.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/aea363c27fd541dba96d2ebfeee4f596c6d34932.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On probe the bcm2835aux UART driver misreports the register base address
as 0x0:
ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550
That's because the driver remaps the registers itself. Take advantage
of the generic remapping code in serial8250_request_std_resource() to
get a message with the correct address and to simplify the driver.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/7d1a9bdb05090d8e465fd15cd26d6e81538d07f9.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835aux UART driver stores a struct uart_8250_port in its private
data even though it's only passed once to serial8250_register_8250_port()
(which copies all relevant data) and becomes obsolete afterwards.
Allocate the struct on the stack instead for simplicity and to conserve
memory.
The driver also initializes a spinlock in the struct which is never used.
Drop that as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/421d3aed4c34cc8447ac9c26c320961f1b787f11.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unbinding the bcm2835aux UART driver raises the following error if the
maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module
parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS):
(NULL device *): Removing wrong port: a6f80333 != fa20408b
That's because bcm2835aux_serial_probe() retrieves UART line number 1
from the devicetree and stores it in data->uart.port.line, while
serial8250_register_8250_port() instead uses UART line number 0,
which is stored in data->line.
On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line,
which contains the wrong number. Fix it.
The issue does not occur if the maximum number of 8250 UARTs is >= 2.
Fixes: bdc5f30095 ("serial: bcm2835: add driver for bcm2835-aux-uart")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.6+
Cc: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
-----BEGIN PGP SIGNATURE-----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=e4jk
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.6
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
* tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits)
soc: fsl: qe: remove set but not used variable 'mm_gc'
soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
soc: fsl: qe: drop pointless check in qe_sdma_init()
soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path
soc: fsl: qe: drop broken lazy call of cpm_muram_init()
soc: fsl: qe: make cpm_muram_free() ignore a negative offset
soc: fsl: qe: make cpm_muram_free() return void
soc: fsl: qe: change return type of cpm_muram_alloc() to s32
serial: ucc_uart: access __be32 field using be32_to_cpu
serial: ucc_uart: limit brg-frequency workaround to PPC32
serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
...
Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the applications like microcom do not work if
modem is disabled. To fix them we always return
TIOCM_CTS | TIOCM_DSR | TIOCM_CAR instead of 0 when
using cts_override. Make get_mctrl return actual status
when not using cts_override.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1574687731-21563-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During db410c stress test and when the system is low on memory,
the UART/console becomes unresponsive and never recover back.
This has been narrowed down to the msm_start_rx_dma which does
not manage error cases correctly (e.g. dma mapping failure),
indeed, when an error happens, dma transfer is simply discarded
and so never completed, leading to unconfigured RX path.
This patch fixes this issue by switching to SW/FIFO mode in case
of DMA issue. This mainly consists in resetting the receiver to
apply RX BAM/DMA disabling change and re-enabling the RX level
and stale interrupts (previously disabled for DMA transfers).
The DMA will be re-enabled once memory is available since the
SW/FIFO read function (msm_handle_rx_dm) retries to start dma
on completion.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1578646684-17379-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 driver can probe for many variants of the venerable 16550A
serial port. Some of those probes involve long (20ms) mdelay calls,
which delay system boot. Modern systems and virtual machines don't have
those variants.
Provide a Kconfig option to disable probes for 16550A variants.
Disabling this speeds up the boot of a virtual machine with a serial
console by more than 20ms (a substantial fraction of the ~100ms needed
to boot a carefully configured VM).
Before:
[ +0.021919] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
After:
[ +0.000097] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/20200111022513.GA166267@localhost
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronize only the dirty part of DMA buffer in order to avoid
unnecessary overhead of syncing of the clean part, which is the case
of every serial DMA transfer in practice.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200112180919.5194-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows DMA engine to go into runtime-suspended mode whenever there is
no data to receive, instead of keeping DMA active all the time while TTY
is opened (i.e. permanently active in practice, like in the case of UART
Bluetooth).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200112180919.5194-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
Register are empty, even though TXRDY might be up and controller is able to
receive data. Since the controller sends data only when TXEMPTY is ready,
on RS485, when DMA is not used, the RTS pin is driven low after each byte.
With this patch, the characters will be transmitted when TXRDY is up and
so, RTS pin will remain high between bytes.
The performance improvement on RS485 is about 8% with a baudrate of 300.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200107111656.26308-1-codrin.ciubotariu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not worth to have them in every serial driver and I'm about to add
another helper function.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200109215444.95995-2-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The node pointer in question is not a child node, but the node assigned
to the port device itself, so we should not be using
devm_fwnode_get_gpiod_from_child() [that is going away], but standard
devm_gpiod_get().
To maintain the previous labeling we use gpiod_set_consumer_name() after
we acquire the GPIO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20200104202314.GA13591@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support having SERIAL_QCOM_GENI as a module while
also still preserving serial console support, tweak the
Kconfig requirements to not require =y
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200107010311.58584-2-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support serial console w/ SERIAL_QCOM_GENI=m,
we need to export the uart_console_device() symbol so things
will build
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200107010311.58584-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SGI IOC3 chip has integrated ethernet, keyboard and mouse interface.
It also supports connecting a SuperIO chip for serial and parallel
interfaces. IOC3 is used inside various SGI systemboards and add-on
cards with different equipped external interfaces.
Support for ethernet and serial interfaces were implemented inside
the network driver. This patchset moves out the not network related
parts to a new MFD driver, which takes care of card detection,
setup of platform devices and interrupt distribution for the subdevices.
Serial portion: Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Network part: Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Network part: Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-serial@vger.kernel.org
"earlycon" no need to specify the value string since it uses
stdout-path parameters. However when earlycon and normal console
are not using the same uart port, we need specify value string
to earlycon, this is what we need to do when support dual linux
using jailhouse hypervisor. The 2nd linux will use the uart
of the 1st linux as earlycon.
earlycon=lpuart32,mmio32,0x5a060010,115200 not work for i.MX8QXP.
It is because lpuart32_early_console_setup not support little endian.
Since the original code is to support UPIO_MEM32BE, so if not
UPIO_MEM32, we still take it as UPIO_MEM32BE
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576822230-23125-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EARLYCON_DECLARE is just a wrapper of OF_EARLYCON_DECLARE,
since we already have OF_EARLYCON_DECLARE for lpuart and lpuart32,
so no need EARLYCON_DECLARE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1576822230-23125-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove code from the driver that create and maintain loopback sysfs node.
Instead use the ioctl TIOCMSET with TIOCM_LOOP argument to set HW to
loopback mode.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1578321905-25843-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is the continuation of below mentioned commits which adds wakeup
feature over the UART RX line.
1)commit 3e4aaea7a0 ("tty: serial: qcom_geni_serial: IRQ cleanup")[v2]
2)commit 8b7103f319 ("tty: serial: qcom_geni_serial: Wakeup over UART
RX")[v2]
The following cleanup is done based on upstream comment received on
subsequent versions of the above-mentioned commits to simplifying the code.
- Use devm_kasprintf API in place of scnprintf.
- Use dev_pm_set_dedicated_wake_irq API that will take care of
requesting and attaching wakeup irqs for devices. Also, it sets wakeirq
status to WAKE_IRQ_DEDICATED_ALLOCATED as a result enabling/disabling of
wake irq will be managed by suspend/resume framework. We can remove the
code for enabling and disabling of wake irq from the this driver.
- Use platform_get_irq_optional API to get optional wakeup IRQ for
device.
- Move ISR registration later in probe after uart port gets register with
serial core.
Patch link:
- https://patchwork.kernel.org/patch/11189717/ (v3)
- https://patchwork.kernel.org/patch/11227435/ (v4)
- https://patchwork.kernel.org/patch/11241669/ (v5)
- https://patchwork.kernel.org/patch/11258045/ (v6)
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1578321905-25843-2-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-18-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable bdp is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Timur Tabi <timur@kernel.org>
Link: https://lore.kernel.org/r/20191220001000.39859-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Much like the samsung_tty driver (now I know where they copied the idea
from), the 21285 uart driver uses 2 bytes from the "unused" array of
struct uart_port to keep tx/rx enabled/disabled state. Those fields are
going away (they were never really needed in the first place), so fix up
the 21285 driver by another horrible hack.
Instead of creating a whole structure for just 2 bytes, just use two
bits from the private_data pointer instead, as that pointer is never
used. The two bits reflect if tx/rx is now enabled/disabled.
Astute readers will note that once rx is disabled, nothing ever seems to
turn it back on, making one wonder if anyone has ever done this.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191219145109.GA1962496@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-54-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-53-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-52-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-51-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-49-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-38-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-48-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-47-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-46-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-45-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-44-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20191213000657.931618-43-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-42-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-41-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-40-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-39-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-37-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-36-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-35-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-33-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-32-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-30-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-29-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-28-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-27-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-26-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-24-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-23-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-22-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-21-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-20-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-19-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-18-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-17-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-16-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-15-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-14-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
While at it, remove forward-declaration of atmel_console - it wasn't
needed even at the moment the driver was first time introduced:
commit 1e6c9c2878 ("[ARM] 3242/2: AT91RM9200 support for 2.6 (Serial)")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-13-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-12-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-11-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-10-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-9-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-8-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-7-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
In contrast to 8250/8250_of, legacy_serial on powerpc does fill
(struct plat_serial8250_port). The reason is likely that it's done on
device_initcall(), not on probe. So, 8250_core is not yet probed.
Propagate value from platform_device on 8250 probe - in case powepc
legacy driver it's initialized on initcall, in case 8250_of it will be
initialized later on of_platform_serial_setup().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-6-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 751d001733.
The wrong commit got added to the tty-next tree, the correct one is in
the tty-linus branch.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-aspeed@lists.ozlabs.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191213000657.931618-5-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The samsung_tty driver was trying to abuse the struct uart_port by using
two "empty" bytes for its own use. That's not ok, and was found by
removing those fields from the structure.
Move the variables into the port-specific structure, which is where
everything else for this port already is. There is no space wasted here
as there was an empty "hole" in the structure already for these bytes.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Hyunki Koo <kkoos00@naver.com>
Cc: HYUN-KI KOO <hyunki00.koo@samsung.com>
Cc: Shinbeom Choi <sbeom.choi@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191217140232.GA3489190@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode
register was already written thus the clock selection is ignored.
Fix by doing the baud rate calulation before setting the mode.
Fixes: 5bf5635ac1 ("tty/serial: atmel: add fractional baud rate support")
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191216085403.17050-1-david.engraf@sysgo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:
6.650130: uart_add_one_port
6.663849: register_console
6.664846: tty_open
6.674391: tty_init_dev
6.675456: tty_port_link_device
uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().
Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.
Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.
Suggested-by: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A break interrupt will be generated if the RX line was pulled low, which
means some abnomal behaviors occurred of the UART. In this case, we still
need to clear this break interrupt status, otherwise it will cause irq
storm to crash the whole system.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Yonghan Ye <yonghan.ye@unisoc.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/925e51b73099c90158e080b8f5bed9b3b38c4548.1575460601.git.baolin.wang7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the commit 677fe555cb ("serial: imx: Fix recursive locking bug")
has mentioned the uart driver might cause recursive locking between
normal printing and the kernel debugging facilities (e.g. sysrq and
oops). In the commit it gave out suggestion for fixing recursive
locking issue: "The solution is to avoid locking in the sysrq case
and trylock in the oops_in_progress case."
This patch follows the suggestion (also used the exactly same code with
other serial drivers, e.g. amba-pl011.c) to fix the recursive locking
issue, this can avoid stuck caused by deadlock and print out log for
sysrq and oops.
Fixes: 04896a77a9 ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dbg() macro for the driver is not needed at all, all drivers should
use the common dynamic debugging infrastructure, not roll their own. So
delete the custom macro and convert the driver to use dev_dbg() instead,
providing a lot more information than the previous macro provided.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Hyunki Koo <kkoos00@naver.com>
Cc: HYUN-KI KOO <hyunki00.koo@samsung.com>
Cc: Shinbeom Choi <sbeom.choi@samsung.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191210143706.3928480-7-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use MCK_DIV8 when the clock divider is > 65535. Unfortunately the mode
register was already written thus the clock selection is ignored.
Fix by writing the mode register after calculating the baudrate.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Link: https://lore.kernel.org/r/20191211162954.8393-1-david.engraf@sysgo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the suspend and resume handlers for the versal uart platform driver.
Adds the suspend for sbsa driver.
Sbsa is a subset of the pl011 driver.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1575873048-14313-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning:
drivers/tty/serial/amba-pl011.c: In function check_apply_cts_event_workaround:
drivers/tty/serial/amba-pl011.c:1461:15: warning: variable dummy_read set but not used [-Wunused-but-set-variable]
The data read is useless and can be dropped.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/1575619526-34482-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/tty/serial/samsung_tty.c: In function s3c24xx_serial_rx_chars_dma:
drivers/tty/serial/samsung_tty.c:549:24: warning: variable ufstat set but not used [-Wunused-but-set-variable]
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Link: https://lore.kernel.org/r/1574424258-138975-1-git-send-email-chenwandun@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning:
drivers/tty/serial/omap-serial.c: In function serial_omap_rlsi:
drivers/tty/serial/omap-serial.c:496:16: warning: variable ch set but not used [-Wunused-but-set-variable]
The character read is useless according to the table 23-246 of the omap4
TRM. So we can drop it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/1575617863-32484-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buf member of struct qe_bd is a __be32, so to make this work on
little-endian hosts, use be32_to_cpu when reading it.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
According to Timur Tabi
This bug in older U-Boots is definitely PowerPC-specific
So before allowing this driver to be built for platforms other than
PPC32, make sure that we don't accept malformed device trees on those
other platforms.
Suggested-by: Timur Tabi <timur@kernel.org>
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
For this to work correctly on little-endian hosts, don't access the
device-tree properties directly in native endianness, but use the
of_property_read_u32() helper.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The Soft UART hack is only needed for some PPC-based SOCs. To allow
building this driver for non-PPC, guard soft_uart_init() and its
helpers by CONFIG_PPC32, and use a no-op soft_uart_init() otherwise.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The "soft uart" mechanism is a workaround for a silicon bug which (as
far as I know) only affects some PPC-based SOCs.
The code that determines which microcode blob to request relies on
some powerpc-specific bits (e.g. the mfspr(SPRN_SVR) and hence also
the asm/reg.h header). This makes it a little awkward to allow this
driver to be built for non-PPC based SOCs with a QE, even if they are
not affected by that silicon bug and thus don't need any of the Soft
UART logic.
There's no way around guarding those bits with some ifdeffery, so to
keep that isolated, factor out the
do-we-need-soft-uart-and-if-so-handle-the-firmware to a separate
function, which we can then easily stub out for non-PPC.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Some ARM-based SOCs (e.g. LS1021A) also have a QUICC engine. As
preparation for allowing this driver to build on ARM, replace the
ppc-specific in_be16() etc. by the qe_io* helpers. Done via
coccinelle.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
This driver uses #defines from soc/fsl/cpm.h, so instead of relying on
some other header pulling that in, do that explicitly. This is
preparation for allowing this driver to build on ARM.
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl3leXUUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyY3g/9FAVVdPEaadNtAhQ/zIxcjozDovKq
0q7yOA3aTBTUoNEinm88an6p0dcC4gNKtGukXmzVH2Hhxm9kLRdtpZGYY00tpLUB
9rI7XsgwwHa+hLwsHbIs507sKGFGy5FLr0ChTTGLDEMppnEvjA2hZooYmcB/OgrC
LlFcwbNKGOk/Si9u2bF2nLO0JDoVHnwzpF99saew/nqc7Lfj9e9IPZFom+VjPBUh
AOvRp2H7uBN+WQlpLeFeMDDoeXh34lX0kYqIV/cVkXVnknDGYKV2CBTg2aeX7jd0
QiPHZh6zlW8zNQgaCZRiBAbatVEOnRMRJ++yiqB8hBYp1LMXm6kJ01YSQpXkugoY
Vp9dtzzTARWV/XkKwD4brw9ZEmIDnO+Ed2x2VbUkPJVcXAvzSQWAx82IU0Iuqmcb
9qr6U2Zf/Xk5aFlGPYVH8QOG+QqzIbZNRQ7NlhDlITyW4P6QPu0mw374yYP2wDGL
sP5YSS3YGa0sQcEgDtVnd4z+WTZI4AwXLPaeaLkDhdfHp2FsERUY4TrPs33J99xw
og4EyokVFzjYzlnBPU6WWn7LL+jj5ccXkL3MA4DR4FJOnNGHh7NXfQUH56rrgsq7
F9/8shL5DuTbQkde1uSyUG9Iq/RigVLlV5DQavFm3dSXvZi0E16t5alC5URNTzk7
at8Bogn53QhlmYc=
=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv
-----BEGIN PGP SIGNATURE-----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=nbwY
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
This reverts commit fdc2de8712 ("serial/8250:
Add support for NI-Serial PXI/PXIe+485 devices").
The commit fdc2de8712 ("serial/8250: Add support for NI-Serial
PXI/PXIe+485 devices") introduced a breakage on NI-Serial PXI(e)-RS485
devices, RS-232 variants have no issue. The Linux system can enumerate the
NI-Serial PXI(e)-RS485 devices, but it broke the R/W operation on the
ports.
However, the implementation is working on the NI internal Linux RT kernel
but it does not work in the Linux main tree kernel. This is only affecting
NI products, specifically the RS-485 variants. Reverting the upstream
until a proper implementation that can apply to both NI internal Linux
kernel and Linux mainline kernel is figured out.
Signed-off-by: Je Yen Tam <je.yen.tam@ni.com>
Fixes: fdc2de8712 ("serial/8250: Add support for NI-Serial PXI/PXIe+485 devices")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191127075301.9866-1-je.yen.tam@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
Fixes: 4f01d833fd ("serial: stm32: fix rx error handling")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133843.13189-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver forgets to call pm_runtime_disable in remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118024833.21587-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PL011's ->flush_buffer() implementation releases and reacquires the port
lock. Due to a race condition here, data can end up being added to the
circular buffer but neither being discarded nor being sent out. This
leads to, for example, tcdrain(2) waiting indefinitely.
Process A Process B
uart_flush_buffer()
- acquire lock
- circ_clear
- pl011_flush_buffer()
-- release lock
-- dmaengine_terminate_all()
uart_write()
- acquire lock
- add chars to circ buffer
- start_tx()
-- start DMA
- release lock
-- acquire lock
-- turn off DMA
-- release lock
// Data in circ buffer but DMA is off
According to the comment in the code, the releasing of the lock around
dmaengine_terminate_all() is to avoid a deadlock with the DMA engine
callback. However, since the time this code was written, the DMA engine
API documentation seems to have been clarified to say that
dmaengine_terminate_all() (in the identically implemented but
differently named dmaengine_terminate_async() variant) does not wait for
any running complete callback to be completed and can even be called
from a complete callback. So there is no possibility of deadlock if the
DMA engine driver implements this API correctly.
So we should be able to just remove this release and reacquire of the
lock to prevent the aforementioned race condition.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191118092547.32135-1-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f33cf77661.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 62104b280a.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3b209d253e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0379b1163e.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d338838c09.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a00d9db895.
As Johan says, this driver needs a lot more work and these changes are
only going in the wrong direction:
https://lkml.kernel.org/r/20190523091839.GC568@localhost
Reported-by: Johan Hovold <johan@kernel.org>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running in M-mode we can't use SBI based drivers. Add a new
CONFIG_RISCV_SBI that drivers that do SBI calls can depend on
instead.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Change logic how console_port is setup by using CON_ENABLED flag
instead of index. There will be unique uart_console
structure that's why code can't use id for console_port
assignment.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1573555271-2579-1-git-send-email-shubhrajyoti.datta@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
dma_unmap_sg(dev, sglist, nents, direction);
.. note::
The 'nents' argument to the dma_unmap_sg call must be
the _same_ one you passed into the dma_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
dma_map_sg call.
However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.
So introduce a new entry orig_nent to remember 'nents'.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
Fixes: b4cdc8f61b ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".
When enabling iommu for lpuart + edma, iommu framework may concatenate
two sgs into one.
Fixes: 6250cc30c4 ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1572932977-17866-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses clk_prepare_enable in ulite_probe but uses clk_unprepare
in ulite_remove, which does not match.
Replace clk_unprepare with clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191101085433.10399-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, this warnings are printed on bananapi-r2:
[ 4.935780] mt6577-uart 11004000.serial: IRQ index 1 not found
[ 4.962589] 11002000.serial: ttyS1 at MMIO 0x11002000 (irq = 202, base_baud = 1625000) is a ST16650V2
[ 4.972127] mt6577-uart 11002000.serial: IRQ index 1 not found
[ 4.998927] 11003000.serial: ttyS2 at MMIO 0x11003000 (irq = 203, base_baud = 1625000) is a ST16650V2
[ 5.008474] mt6577-uart 11003000.serial: IRQ index 1 not found
Fix this by calling platform_get_irq_optional() instead.
now it looks like this:
[ 4.872751] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191027062117.20389-1-frank-w@public-files.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the commit 7723f4c5ec ("driver core: platform: Add an error message
to platform_get_irq*()") platform_get_irq() started issuing an error message.
Thus, there is no need to have the same in the driver
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191023103558.51862-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_qca interfaces to the wcn3990 via a uart_dm on the msm8998 mtp and
Lenovo Miix 630 laptop. As part of initializing the wcn3990, hci_qca
disables flow, configures the uart baudrate, and then reenables flow - at
which point an event is expected to be received over the uart from the
wcn3990. It is observed that this event comes after the baudrate change
but before hci_qca re-enables flow. This is unexpected, and is a result of
msm_reset() being broken.
According to the uart_dm hardware documentation, it is recommended that
automatic hardware flow control be enabled by setting RX_RDY_CTL. Auto
hw flow control will manage RFR based on the configured watermark. When
there is space to receive data, the hw will assert RFR. When the watermark
is hit, the hw will de-assert RFR.
The hardware documentation indicates that RFR can me manually managed via
CR when RX_RDY_CTL is not set. SET_RFR asserts RFR, and RESET_RFR
de-asserts RFR.
msm_reset() is broken because after resetting the hardware, it
unconditionally asserts RFR via SET_RFR. This enables flow regardless of
the current configuration, and would undo a previous flow disable
operation. It should instead de-assert RFR via RESET_RFR to block flow
until the hardware is reconfigured. msm_serial should rely on the client
to specify that flow should be enabled, either via mctrl() or the termios
structure, and only assert RFR in response to those triggers.
Fixes: 04896a77a9 ("msm_serial: serial driver for MSM7K onboard serial peripheral.")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Gross <agross@kernel.org>
Link: https://lore.kernel.org/r/20191021154616.25457-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commits adds RS485 support for LPUART hardware that uses 32-bit
registers. These are typically found in i.MX8 processors.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-3-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use define from the 32-bit register description UARTMODIR_* instead of
UARTMODEM_*. The value is the same, so there is no functional change.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-2-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently flow control is not working due to lpuart32_set_mctrl that is
clearing TXCTSE bit in all cases. This bit gets earlier setup by
lpuart32_set_termios.
As I read in Documentation set_mctrl is also not meant for hardware
flow control rather than gpio setting and clearing a RTS signal.
Therefore I guess it is safe to remove the whole code in
lpuart32_set_mctrl.
This was tested with console on a i.MX8QXP SoC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20191017141428.10330-1-philippe.schenker@toradex.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have symbol namespaces, use them in MCB to not pollute the
default namespace with MCB internals.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191016100158.1400-1-jthumshirn@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 91daae0318.
The origin patch is causing an issue on r8a7791/koelsch and
r8a7795/salvator-xs platforms where cons->index is not initialized to
expected value.
It is safer to revert this patch for now till it is clear why this is
happening.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/59f51af6bb03fce823663764d17ad0291aa01ab2.1571222199.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current checking for failure on the number of ports fails when
-ENODEV is returned from the call to get_num_ports. Fix this by making
num_ports and loop counter i signed rather than unsigned ints. Also
add check for num_ports being less than zero to check for -ve error
returns.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: e2fea54e45 ("8250-men-mcb: add support for 16z025 and 16z057")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191013220016.9369-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a one more step to consolidate Exar bits under 8250_exar umbrella.
This time we introduce a custom ->startup() callback where the Exar specific
settings are applied.
Cc: Robert Middleton <robert.middleton@rm5248.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191011115610.81507-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
The sirfsoc_usp and sirfsoc_uart objects are not
used outside of the drivers/tty/serial/sirfsoc_uart.o
so make them static. Fixes following sparse warnings:
drivers/tty/serial/sirfsoc_uart.h:123:30: warning: symbol 'sirfsoc_usp' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:189:30: warning: symbol 'sirfsoc_uart' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191009135356.11180-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add system wakeup capability over UART RX line for wakeup capable UART.
When system is suspended, RX line act as an interrupt to wakeup system
for any communication requests from peer.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1570700803-17566-1-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move ISR registration from startup to probe function to avoid registering
it everytime when the port open is called for driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1570700763-17319-1-git-send-email-akashast@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All i.MX SoCs except i.MX1 have ONLY one necessary IRQ, use
platform_get_irq_optional() to get second/third IRQ which are
optional to avoid below error message during probe:
[ 0.726219] imx-uart 30860000.serial: IRQ index 1 not found
[ 0.731329] imx-uart 30860000.serial: IRQ index 2 not found
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1570614559-11900-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old early platform device support is now sh-specific. Before moving on
to implementing new early platform framework based on real platform
devices, prefix all early platform symbols with 'sh_'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two checks to see if the manual gpio is configured, but
these the check is seeing if the structure is NULL instead it
should check to see if there are CTS and/or RTS pins defined.
This patch uses checks for those individual pins instead of
checking for the structure itself to restore auto RTS/CTS.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-2-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using mctrl_gpio_to_gpiod, it dereferences gpios into a single
requested GPIO. This dereferencing can break if gpios is NULL,
so this patch adds a NULL check before dereferencing it. If
gpios is NULL, this function will also return NULL.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix incorrect read-modify-write sequence in lpuart_flush_buffer() that
was reading from UARTPFIFO and writing to UARTCFIFO instead of
operating solely on the latter.
Fixes: 9bc19af9da ("tty: serial: fsl_lpuart: Flush HW FIFOs in .flush_buffer")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Jiri Slaby <jslaby@suse.com>
Link: https://lore.kernel.org/r/20191004215537.5308-1-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two parts which should be fixed. The first one is to assigned
uartps_major at the end of probe() to avoid complicated logic when
something fails.
The second part is initialized uartps_major number to 0 when last device is
removed. This will ensure that on next probe driver will ask for new
dynamic major number.
Fixes: ab26266601 ("serial: uartps: Use the same dynamic major number for all ports")
Reported-by: Paul Thomas <pthomas8589@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d2652cda992833315c4f96f06953eb547f928918.1570194248.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the SIRQ polarity for Aspeed AST24xx/25xx VUART configurable via
sysfs. This setting need to be changed on specific host platforms
depending on the selected host interface (LPC / eSPI).
The setting is configurable via sysfs rather than device-tree to stay in
line with other related configurable settings.
On AST2500 the VUART SIRQ polarity can be auto-configured by reading a
bit from a configuration register, e.g. the LPC/eSPI interface
configuration bit.
Tested: Verified on TYAN S7106 mainboard.
Signed-off-by: Oskar Senft <osk@google.com>
Link: https://lore.kernel.org/r/20190905144130.220713-1-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call uart_unregister_driver() conditionally instead of
unconditionally, only if it has been previously registered.
This uses driver.state, just as the sh-sci.c driver does.
Fixes this null pointer dereference in tty_unregister_driver(),
since the 'driver' argument is null:
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:tty_unregister_driver+0x25/0x1d0
Fixes: 238b8721a5 ("[PATCH] serial uartlite driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable <stable@vger.kernel.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following an incorrect indentation reported to me by Dan Carpenter, I
noticed that the SysRq lines were inherited from the lpuart driver[1] (note
how the 'continue' is aligned to 'sport->port.sysrq = 0') and we have never
actually tested the SysRq support.
'sport->sysrq = 0' is not necessary neither before nor after 'continue',
because sysrq will already be 0 after uart_handle_sysrq_char() will finish.
Also, since the LINFlexD driver never called uart_handle_break(), sysrq
would have never been set to a nonzero value, so uart_handle_sysrq_char()
was not going to do anything.
Break conditions are detected based on a null data byte along with a
framing error (stop bit sampled to 0).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/tty/serial/fsl_lpuart.c?h=b3e3bf2ef2c74f5ce5c19510edbbb9bfc1d249c2#n659
Fixes: 09864c1cdf ("tty: serial: Add linflexuart driver for S32V234")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190918184439.7465-1-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, scary warnings may be printed for optional interrupts:
sh-sci e6550000.serial: IRQ index 1 not found
sh-sci e6550000.serial: IRQ index 2 not found
sh-sci e6550000.serial: IRQ index 3 not found
sh-sci e6550000.serial: IRQ index 4 not found
sh-sci e6550000.serial: IRQ index 5 not found
Fix this by calling platform_get_irq_optional() instead for all but the
first interrupts, which are optional.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191001180743.1041-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sifive serial driver implements earlycon support, but unless
another driver is built in that supports earlycon support it won't
be usable. Explicitly select SERIAL_EARLYCON instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Link: https://lore.kernel.org/r/20190910055923.28384-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored except deferred probe. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190925162617.30368-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
While at that, remove the now duplicated code from qrp_serial_setup().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191001115825.795700-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_dma_probe() is only used in pl011_dma_startup() which does only
exist when CONFIG_DMA_ENGINE=y, so remove the unused dummy version to
silence the warning.
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/1568726340-4518-1-git-send-email-cai@lca.pw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason for this patch is xilinx_uartps driver which create one dynamic
instance per IP with unique major and minor combinations. drv->nr is in
this case all the time setup to 1. That means that uport->line is all the
time setup to 0 and drv->tty_driver->name_base is doing shift in name to
for example ttyPS3.
register_console() is looping over console_cmdline array and looking for
proper name/index combination which is in our case ttyPS/3.
That's why every instance of driver needs to be registered with proper
combination of name/number (ttyPS/3). Using uport->line is doing
registration with ttyPS/0 which is wrong that's why proper console index
should be used which is in cons->index field.
Also it is visible that recording console should be done based on
information about console not about the port but in most cases numbers are
the same and xilinx_uartps is only one exception now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4a877f1c7189a7c45b59a6ebfc3de607e8758949.1567434470.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
Currently it is not possible to use rs485 as pointer to
rs485_config struct in struct uart_port is NULL in case we
configure the port through device tree.
Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/20190913050105.1132080-1-hs@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to access the UART without the interrupts, the kernel uses
the basic polling methods for IO with the device. With these methods
implemented, it is now possible to enable kgdb during early boot over serial.
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/f112a741c053ac5fb0637e2f058be81e17f78ccc.1568862391.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using only 4 DMA periods for UART RX is very few if we have a high
frequency of small transfers - like in our case using Bluetooth with
many small packets via UART - causing many dma transfers but in each
only filling a fraction of a single buffer. Such a case may lead to
the situation that DMA RX transfer is triggered but no free buffer is
available. When this happens dma channel ist stopped - with the patch
"dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
possible consequences that:
with disabled hw flow control:
If enough data is incoming on UART port the RX FIFO runs over and
characters will be lost. What then happens depends on upper layer.
with enabled hw flow control:
If enough data is incoming on UART port the RX FIFO reaches a level
where CTS is deasserted and remote device sending the data stops.
If it fails to stop timely the i.MX' RX FIFO may run over and data
get lost. Otherwise it's internal TX buffer may getting filled to
a point where it runs over and data is again lost. It depends on
the remote device how this case is handled and if it is recoverable.
Obviously we want to avoid having no free buffers available. So we
decrease the size of the buffers and increase their number and the
total buffer size.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190923135916.1212-1-philipp.puschmann@emlix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull kernel lockdown mode from James Morris:
"This is the latest iteration of the kernel lockdown patchset, from
Matthew Garrett, David Howells and others.
From the original description:
This patchset introduces an optional kernel lockdown feature,
intended to strengthen the boundary between UID 0 and the kernel.
When enabled, various pieces of kernel functionality are restricted.
Applications that rely on low-level access to either hardware or the
kernel may cease working as a result - therefore this should not be
enabled without appropriate evaluation beforehand.
The majority of mainstream distributions have been carrying variants
of this patchset for many years now, so there's value in providing a
doesn't meet every distribution requirement, but gets us much closer
to not requiring external patches.
There are two major changes since this was last proposed for mainline:
- Separating lockdown from EFI secure boot. Background discussion is
covered here: https://lwn.net/Articles/751061/
- Implementation as an LSM, with a default stackable lockdown LSM
module. This allows the lockdown feature to be policy-driven,
rather than encoding an implicit policy within the mechanism.
The new locked_down LSM hook is provided to allow LSMs to make a
policy decision around whether kernel functionality that would allow
tampering with or examining the runtime state of the kernel should be
permitted.
The included lockdown LSM provides an implementation with a simple
policy intended for general purpose use. This policy provides a coarse
level of granularity, controllable via the kernel command line:
lockdown={integrity|confidentiality}
Enable the kernel lockdown feature. If set to integrity, kernel features
that allow userland to modify the running kernel are disabled. If set to
confidentiality, kernel features that allow userland to extract
confidential information from the kernel are also disabled.
This may also be controlled via /sys/kernel/security/lockdown and
overriden by kernel configuration.
New or existing LSMs may implement finer-grained controls of the
lockdown features. Refer to the lockdown_reason documentation in
include/linux/security.h for details.
The lockdown feature has had signficant design feedback and review
across many subsystems. This code has been in linux-next for some
weeks, with a few fixes applied along the way.
Stephen Rothwell noted that commit 9d1f8be5cf ("bpf: Restrict bpf
when kernel lockdown is in confidentiality mode") is missing a
Signed-off-by from its author. Matthew responded that he is providing
this under category (c) of the DCO"
* 'next-lockdown' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (31 commits)
kexec: Fix file verification on S390
security: constify some arrays in lockdown LSM
lockdown: Print current->comm in restriction messages
efi: Restrict efivar_ssdt_load when the kernel is locked down
tracefs: Restrict tracefs when the kernel is locked down
debugfs: Restrict debugfs when the kernel is locked down
kexec: Allow kexec_file() with appropriate IMA policy when locked down
lockdown: Lock down perf when in confidentiality mode
bpf: Restrict bpf when kernel lockdown is in confidentiality mode
lockdown: Lock down tracing and perf kprobes when in confidentiality mode
lockdown: Lock down /proc/kcore
x86/mmiotrace: Lock down the testmmiotrace module
lockdown: Lock down module params that specify hardware parameters (eg. ioport)
lockdown: Lock down TIOCSSERIAL
lockdown: Prohibit PCMCIA CIS storage when the kernel is locked down
acpi: Disable ACPI table override if the kernel is locked down
acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down
ACPI: Limit access to custom_method when the kernel is locked down
x86/msr: Restrict MSR access when the kernel is locked down
x86: Lock down IO port access when the kernel is locked down
...
Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIXfw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmNACeIYq7038NXGBXBj1DfN90GeGNenwAnRkjzF+6
YwEhFRxOMglnbvDevgPU
=E6jv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Even in this age, people are still making new serial port silicon,
why...
Anyway, here's the TTY and Serial driver update for 5.4-rc1. Lots of
changes in here for a number of embedded serial port devices that are
being worked on because people really like to see those console
logs...
Other than that, nothing major here, no core tty changes that anyone
should care about.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (125 commits)
serial: tegra: Add PIO mode support
serial: tegra: report clk rate errors
serial: tegra: add support to adjust baud rate
serial: tegra: DT for Adjusted baud rates
serial: tegra: add support to use 8 bytes trigger
serial: tegra: set maximum num of uart ports to 8
serial: tegra: check for FIFO mode enabled status
dt-binding: serial: tegra: add new chips
serial: tegra: report error to upper tty layer
serial: tegra: flush the RX fifo on frame error
serial: tegra: avoid reg access when clk disabled
serial: tegra: add support to ignore read
serial: sprd: correct the wrong sequence of arguments
dt-bindings: serial: Convert riscv,sifive-serial to json-schema
serial: max310x: turn off transmitter before activating AutoCTS or auto transmitter flow control
serial: max310x: Properly set flags in AutoCTS mode
tty: serial: fix platform_no_drv_owner.cocci warnings
dt-bindings: serial: Document Freescale LINFlexD UART
serial: fsl_linflexuart: Update compatible string
tty: n_gsm: avoid recursive locking with async port hangup
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
Add PIO mode support in receive and transmit path with RX interrupt
trigger of 16 bytes for Tegra194 and older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-13-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard UART controllers support +/-4% baud rate error tolerance.
Tegra186 only supports 0% to +4% error tolerance whereas other Tegra
chips support standard +/-4% rate. Add chip data for knowing error
tolerance level for each soc. Creating new compatible for Tegra194
chip as it supports baud rate error tolerance of -2 to +2%, different
from older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-12-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to adjust baud rates to fall under supported tolerance
range through DT.
Tegra186 chip has a hardware issue resulting in frame errors when
tolerance level for baud rate is negative. Provided entries to adjust
baud rate to be within acceptable range and work with devices that
can send negative baud rate. Also report error when baud rate set is
out of tolerance range of controller updated in device tree.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-11-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set maximum number of UART ports to 8 as older chips have 5 ports and
Tergra186 and later chips will have 8 ports. Add this info to chip
data. Read device tree compatible of this driver and register uart
driver with max ports of matching chip data.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-8-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chips prior to Tegra186 needed delay of 3 UART clock cycles to avoid
data loss. This issue is fixed in Tegra186 and a new flag is added to
check if FIFO mode is enabled. chip data updated to check if this flag
is available for a chip. Tegra186 has new compatible to enable this
flag.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-7-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report overrun/parity/frame/break errors to top tty layer. Add support
to ignore break character if IGNBRK is set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIFO reset/flush code implemented now does not follow programming
guidelines. RTS line has to be turned off while flushing FIFOs to
avoid new transfers. Also check LSR bits UART_LSR_TEMT and UART_LSR_DR
to confirm FIFOs are flushed.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-4-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids two race conditions from the UART shutdown sequence both
leading to 'Machine check error in AXI2APB' and kernel oops.
One was that the clock was disabled before the DMA was terminated making
it possible for the DMA callbacks to be called after the clock was
disabled. These callbacks could write to the UART registers causing
timeout.
The second was that the clock was disabled before the UART was
completely flagged as closed. This is done after the shutdown is called
and a new write could be started after the clock was disabled.
tegra_uart_start_pio_tx could be called causing timeout.
Given that the baud rate is reset at the end of shutdown sequence, this
fix is to examine the baud rate to avoid register access from both race
conditions.
Besides, terminate the DMA before disabling the clock.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Shardar Mohammed <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-3-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to ignore read characters if CREAD flag is not set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sequence of arguments which was passed to handle_lsr_errors() didn't
match the parameters defined in that function, &lsr was passed to flag
and &flag was passed to lsr, this patch fixed that.
Fixes: b7396a38fb ("tty/serial: Add Spreadtrum sc9836-uart driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190905074151.5268-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As documented in the data-sheet, the transmitter must be disabled before
activating AutoCTS or auto transmitter flow control. Accordingly, the
transmitter must be enabled after AutoCTS or auto transmitter flow
control gets deactivated.
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
Link: https://lore.kernel.org/r/20190904121746.4641-1-c.vogtlaender@sigma-surface-science.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 391f93f2ec ("serial: core: Rework hw-assisted flow control
support") has changed the way the AutoCTS mode is handled.
According to that change, serial drivers which enable H/W AutoCTS mode must
set UPSTAT_AUTORTS, UPSTAT_AUTOCTS and UPSTAT_AUTOXOFF to prevent the
serial core from inadvertently disabling RX or TX. This patch adds proper
handling of UPSTAT_AUTORTS, UPSTAT_AUTOCTS and UPSTAT_AUTOXOFF flags.
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
Link: https://lore.kernel.org/r/20190904121141.4570-1-c.vogtlaender@sigma-surface-science.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/fsl_linflexuart.c:907:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: b953815b819b ("tty: serial: Add linflexuart driver for S32V234")
CC: Stefan-gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190825142837.zt3hpa22c7iofg3v@48261080c7f1
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sprd serial console can work with only 26M fixed clock,
but the probe() is returning fail if the clock "enable" is not
configured in device tree.
This patch will fix the problem to let the uart device which is
used for console can be initialized even missing "enable" clock
configured in devicetree. We should make sure the debug function
as available as we can.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-4-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use console_initcall to save the console index we selected on the
command line to sprd_console before probe finished. Thus we can
make different processes to the uart devices during initialization
according to whether it is used for console.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling sprd_console_setup(), sprd_uart_port probably is NULL,
we should check that first instead of checking its items directly.
Also we should check membase to avoid accessing uart device before
its initialization finished.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/20190826072929.7696-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 18dfef9c7f ("serial: atmel: convert to irq handling
provided mctrl-gpio"), the GPIOs interrupts are handled by
mctrl_gpio_irq_handle().
So, atmel_get_lines_status() can be completely killed and replaced by :
atmel_uart_readl(port, ATMEL_US_CSR);
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20190826071752.30396-1-richard.genoud@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should help to avoid unnecessary gaps in transmission while
adding little overhead due to low default Tx threshold level (2
bytes).
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-6-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): avoid writing baud rate divider registers when the
values to be written are the same as current. Any writing seems to
restart transmission/receiving logic in the hardware, that leads to
data breakage even when rate doesn't in fact change. E.g., user
switches RTS/CTS handshake and suddenly gets broken bytes.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-5-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): disabling individual interrupt requests in UART for
duration of the routine is pointless. Get rid of it.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): stopping receiver and transmitter does harm when
something that doesn't touch transmission format/rate changes, such as
RTS/CTS handshake.
OTOH, it does no good on baud rate or format change, as
synchronization on upper-level protocols is still required to do it
right.
Therefore, just stop doing it.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): remove busy-waiting "drain Tx FIFO" loop. Worse
yet, it was potentially unbounded wait due to RTS/CTS (hardware)
handshake.
Let user space ensure draining is done before termios change, if
draining is needed in the first place.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-2-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change split the insertion loop into two parts. The first part
accessed bytes 0, 1, ... (rxlen - 2), and the second part by mistake
took offset `rxlen` instead of the correct `rxlen - 1`. So one byte was
not stored, and the final access wrote past the end of the rx_buf.
Fixes: 9c12d739d6 (tty: max310x: Split uart characters insertion loop)
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/13ea227620aaad8a7231d42ed03a8508297d4eb3.1567027079.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190827114614.102037-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There may be setups, where legacy interrupts are not available. This is
the caese, e.g., when Linux runs as guest (aka. non-root cell) of the
partitioning hypervisor Jailhouse. There, only MSI(-X) interrupts are
available for guests.
But the 8250_pci driver currently only supports legacy ints. So let's
enable MSI(-X) interrupts.
Nevertheless, this needs to handled with care: while many 8250 devices
actually claim to support MSI(-X) interrupts it should not be enabled be
default. I had at least one device in my hands with broken MSI
implementation.
So better introduce a whitelist with devices that are known to support
MSI(-X) interrupts. I tested all devices mentioned in the patch.
Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Link: https://lore.kernel.org/r/20190812112152.693622-1-ralf.ramsauer@oth-regensburg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81504A/508A/512A is PCIE to 4/8/12 UARTs device. It's support
IO/MMIO/PCIE conf to access all functions. The old F81504/508/512 is
only support IO.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/1565933249-23076-1-git-send-email-hpeter+linux_kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description of the modem line control GPIOs contain a boolean type to set
direction of the line. Since GPIO library provides an enumerator type of flags,
we may utilize it and allow a bit more flexibility on the choice of the type of
the line parameters. It also removes an additional layer of value conversion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814140759.17486-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_FSL_LINFLEXUART=y and CONFIG_PRINTK is not set,
one compilation error is found as below:
drivers/tty/serial/fsl_linflexuart.c: In function linflex_earlycon_putchar:
drivers/tty/serial/fsl_linflexuart.c:608:31: error: CONFIG_LOG_BUF_SHIFT undeclared
(first use in this function); did you mean CONFIG_ISA_BUS_API?
if (earlycon_buf.len >= 1 << CONFIG_LOG_BUF_SHIFT)
^~~~~~~~~~~~~~~~~~~~
CONFIG_ISA_BUS_API
This because CONFIG_LOG_BUF_SHIFT is depended on CONFIG_PRINTK, fix this
by adding dependence for CONFIG_SERIAL_FSL_LINFLEXUART.
Fixes: b953815b819b ("tty: serial: Add linflexuart driver for S32V234")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Link: https://lore.kernel.org/r/20190820124015.28409-1-maowenan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moxa serial boards only need a special setup function, we can use
generic 8250 framework for other parts.
So let's merge 8250_moxa to 8250_pci.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190816165124.16942-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-4-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER and DLH registers occupy the same address space, selected by
the LCR.DLAB bit. Hence, add port lock to protect IER when LCR.DLAB bit
is set.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the internal loopback functionality that can be enabled with
TIOCM_LOOP.
Signed-off-by: Andreas Abel <aabel@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When half-duplex RS485 communication is used, after RX is started, TX
tasklet still needs to be scheduled tasklet. This avoids console freezing
when more data is to be transmitted, if the serial communication is not
closed.
Fixes: 69646d7a36 ("tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190813074025.16218-1-razvan.stefanescu@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce support for LINFlex driver, based on:
- the version of Freescale LPUART driver after commit b3e3bf2ef2 ("Merge
4.0-rc7 into tty-next");
- commit abf1e0a980 ("tty: serial: fsl_lpuart: lock port on console
write").
In this basic version, the driver can be tested using initramfs and relies
on the clocks and pin muxing set up by U-Boot.
Remarks concerning the earlycon support:
- LinFlexD does not allow character transmissions in the INIT mode (see
section 47.4.2.1 in the reference manual[1]). Therefore, a mutual
exclusion between the first linflex_setup_watermark/linflex_set_termios
executions and linflex_earlycon_putchar was employed and the characters
normally sent to earlycon during initialization are kept in a buffer and
sent afterwards.
- Empirically, character transmission is also forbidden within the last 1-2
ms before entering the INIT mode, so we use an explicit timeout
(PREINIT_DELAY) between linflex_earlycon_putchar and the first call to
linflex_setup_watermark.
- U-Boot currently uses the UART FIFO mode, while this driver makes the
transition to the buffer mode. Therefore, the earlycon putchar function
matches the U-Boot behavior before initializations and the Linux behavior
after.
[1] https://www.nxp.com/webapp/Download?colCode=S32V234RM
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Adrian.Nitu <adrian.nitu@freescale.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Ana Nedelcu <B56683@freescale.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Matthew Nunez <matthew.nunez@nxp.com>
[stefan-gabriel.mirea@nxp.com: Reduced for upstreaming and implemented
earlycon support]
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Link: https://lore.kernel.org/r/20190809112853.15846-6-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190809174042.6276-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to Sunix serial boards with up to 16 ports.
Sunix board need its own setup callback instead of using Timedia's, to
properly support more than 4 ports.
Cc: Morris Ku <morris_ku@sunix.com>
Cc: Debbie Liu <debbie_liu@sunix.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190809190130.30773-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform is getting removed, so there are no more users
of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809202749.742267-3-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver/IP is reused across multiple SoCs. Older SoCs supported three
separate IRQs for tx, rx & err interrupts. Newer Lightning Mountain SoC
supports single IRQ for all of tx/rx/err interrupts. This patch modifies
the driver design to support dynamic assignment of IRQ resources & ISRs
based on devicetree node compatible entries.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/b166a0593bee191fcd77b5bdf8fedc6f6330a371.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use explicit string instead of a macro for devicetree compatible string.
This series of patches is to add support for multiple SoCs which reuse the same
serial controller IP. The following patches will add another compatible string
to support new Lightning Mountain(LGM) SoC. So it makes sense to have the
compatible strings explicitly mentioned instead of a fixed macro.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/57e2b69e9fbd93328a477b4c7dd2dcc78784ecb1.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Elkhart Lake may use High Speed UART from OSE IP block.
This is different to what we have in main LPSS, though compatible
with older version of it, which is handled by this driver.
Enable OSE HS UART on Intel Elkhart Lake by adding PCI IDs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace LPSS_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is really useful not only for debugging to have an DMA IRQ line and
pool being mapped to the corresponding IP by using its instance ID.
Provide PCI device and function as instance ID for Intel Quark UART DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups specific get_divisor() and set_divisor() hook.
Among other changes the FIFO size is now retrieved from the hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a common library module for Synopsys DesignWare UART,
let us use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a common library module for Synopsys DesignWare UART,
let us use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would like to use same functions in the couple of drivers for
Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand
library module which users will select explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of pointer will simplify enabling runtime PM for the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2cb78eab23 ("serial: 8250_dw: Use a unified new dev variable in
probe") introduced a local dev variable in ->probe(). Do the same in ->remove()
in order to prepare for sequential patches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20190806094322.64987-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing driver can only support single core SoC. But new multicore
platforms which reuse the same driver/IP need SMP support. This patch adds
multicore support in the driver.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/7912786cccad60c72b20ea724af1def505ab22aa.1565160764.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling TIE in .startup() callback causes the driver to start (or at
least try) to transmit data before .start_tx() is called. Which, while
harmless (since TIE handler will immediately disable it), is a no-op
and shouldn't really happen. Drop UARTCR2_TIE from list of bits set in
lpuart_startup().
This change will also not enable TIE in .resume(), but it seems that,
similart to .startup(), transmit interrupt shouldn't be enabled there
either.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-6-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most users of lpuart*_setup_watermark() enable identical set of flags
right after the call, so combine those two action into a subroutine
and make use of it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code doing final steps of TX/RX configuration in lpuart32_startup()
and lpuart_resume() is identical, so move it into a standalone
subroutine.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-4-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in Documentation/timers/timers-howto.rst
the small amount of milliseconds sometimes produces
much longer delays.
Replace msleep(1) with usleep_range(1000, 1100).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190805142535.21948-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190802130817.16220-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-4-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-3-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_GPIOLIB is not enabled, mctrl_gpio_init() and
mctrl_gpio_init_noauto() will currently return an error pointer with
-ENOSYS. As the mctrl GPIOs are usually optional, drivers need to
check for this condition to allow continue probing.
To avoid the need for this check in each driver, we return NULL
instead, as all the mctrl_gpio_*() functions are skipped anyway.
We also adapt mctrl_gpio_to_gpiod() to be in line with this change.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-1-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move INT0 clearing out of common, per-port serial8250_do_startup()
into PCI device probe/resume.
As described in commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs"),
the purpose of clearing INT0 is to prevent the PCI interrupt line from
becoming stuck asserted, "which is fatal with edge-triggered MSIs".
Like the clearing via interrupt handler that moved from common code in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up
handling"), this clearing at startup can be better handled at the PCI
device level.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190801185956.3222-1-asierra@xes-inc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit b6b996b6cd ("treewide: Use DEVICE_ATTR_RW") converted
the rx_fifo_timeout attribute, it forgot to convert rx_fifo_trigger due
to a slightly different function naming.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20190731124555.14349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For QUP IP versions 2.5 and above the oversampling rate is halved
from 32 to 16. Update this rate after reading hardware version
register, so that the clock divider value is correctly set to
achieve required baud rate.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Link: https://lore.kernel.org/r/20190801121153.10613-1-vivek.gautam@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When closing and shutting down the exar serial port, if the chip
has not finished sending all of the data in its buffer, the
remaining bytes will be lost. Hold off on the shutdown until the
bytes have all been sent.
Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Link: https://lore.kernel.org/r/20190801145640.26080-1-robert.middleton@rm5248.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are Exar custom divisor support in 8250_port which belongs to
8250_exar module. Move it out to the correct module and do not contaminate
generic code with it.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are Exar quirks in 8250_port which belong to 8250_exar module.
Extract PM routine to the correct module and do not contaminate generic code
with it.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a separate driver there is no need to autoconfigure ports,
we already know what they are.
Drop autoconfiguration in 8250_port and move type detection to 8250_exar.
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a driver, do not call "raw" sysfs functions, instead call driver
core ones. Specifically convert the use of sysfs_create_file() and
sysfs_remove_file() to use device_create_file() and device_remove_file()
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20190704084617.3602-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A powerpc allyesconfig build produces this warning:
In file included from include/linux/radix-tree.h:16,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/device.h:16,
from include/linux/platform_device.h:13,
from drivers/tty/serial/xilinx_uartps.c:16:
drivers/tty/serial/xilinx_uartps.c: In function 'cdns_uart_console_write':
include/linux/spinlock.h:288:3: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
_raw_spin_unlock_irqrestore(lock, flags); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/xilinx_uartps.c:1197:16: note: 'flags' was declared here
unsigned long flags;
^~~~~
It looks like gcc just can't track the relationship between "locked"
and "flags", and it is obvious that "flags" won't be used when "locked"
is zero, so the simplest thing is to initialise flags.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20190731160557.6a09c3e1@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Last steps of .shutdown() code are identical for lpuart and lpuart32
cases, so move it all into a standalone subroutine.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-19-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By the time lpuart_shutdown() calls lpuart_stop_tx() UARTCR2_TE and
UARTCR2_TIE (which the latter will clear) are already cleared, so that
function call should effectively be a no-op. Moreso, lpuart_stop_tx()
is expected to be executed with port spinlock held, which the caller
doesn't. Given all that, drop the call to lpuart_stop_tx() in
lpuart_shutdown().
In case of lpuart32_shutdown()/lpuart32_stop_tx(), TIE won't even be
set if lpuart_dma_tx_use is true. Drop it there as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-18-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use cpu_relax() instead of barrier() in a tight polling loops to make
them a bit more idiomatic. Should also improve things on ARM64 a bit
since cpu_relax() will expand into "yield" instruction there.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-16-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Busy polling on a bit in a register is used in multiple places in the
driver. Move it into a shared function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-15-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.
Fixes: a5fa2660d7 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing CSTOPB bit if it is set is functionally equivalent to jsut
clearing it unconditionally. Drop unnecessary check.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-13-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for termios->c_cflag & CRTSCTS ensure that if we reach else
branch, CRTSCTS in termios->c_cflag is already going to be
cleard. Doing so explicitly there is not necessary. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-11-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While sharing code for Tx interrupt handler between 8 and 32 bit
variant of the peripheral saves a bit of code duplication it also adds
quite a number of lpuart_is_32() checks which makes it harder to
understand. Move shared bits back into corresponding
lpuart*_transmit_buffer functions, split lpuart_txint into
lpuart_txint and lpuart32_txint so we can drop all extra
lpuart_is_32() check and make the code flow more linear.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-10-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although I haven't observed this bug in practice, it seems that the
code for handling x_char of LPUART is pretty much identical to that of
i.MX. So the fix found in commit 7e2fb5aa8d ("serial: imx: Fix issue
in software flow control"):
serial: imx: Fix issue in software flow control
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
should apply here as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-9-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uart_write_wakeup() will already be called as a part of
lpuart*_transmit_buffer() call, so there doesn't seem to be a reason
to call it again right after.
It also appears that second uart_write_wakeup() might potentially
cause unwanted write wakeup when transmitting an x_char. See commit
5e42e9a30c ("serial: imx: Fix x_char handling and tx flow control")
where this problem was fixed in a very similarly structured i.MX UART
driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-8-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that lpuart_rxint, lpuart_txint and lpuart32_rxint were
modelled after identical function found in UART driver for
i.MX. However, while said functions are used as individual IRQ
handlers in i.MX driver (in case of i.MX1), it is not the case for
LPUART. Given that, there's no need for us to restrict the prototype
of the handler to irqreturn_t foo(int, void *) and we can drop all of
uneened boilerplate code by changing it void foo(struct lpuart_port *).
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After overruns the FIFO pointers become misaligned. This
typically shows by characters still being stuck in the FIFO
despite the empty flag being asserted. After the first
assertion of the overrun flag the empty flag still seems to
indicate FIFO state correctly and all data can be read.
However, after another overrun assertion the FIFO seems to
be off by one such that the last received character is still
in the FIFO (despite the empty flag being asserted).
Flushing the receive FIFO reinitializes pointers. Hence it
is recommended to flush the FIFO after overruns, see also:
https://community.nxp.com/thread/321175
Hence, on assertion of the overrun flag read the remaining
data from the FIFO and flush buffers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-3-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using DMA framing error get cleared properly. However, due
to the additional read from the data register, an underflow in
the receive FIFO buffer occurs (the FIFO pointer gets out of
sync).
Clear the FIFO in case an underflow has occurred. Also disable the
receiver during this operation and when reading the data register to
minimize potential interference.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-2-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Called in only one place, for RS232, it only obscures things, as it
doesn't go well with 2 similar named functions,
imx_uart_rts_inactive() and imx_uart_rts_active(), that both are
RS485-specific.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_uart_set_mctrl() happened to set UCR2_CTSC bit whenever TIOCM_RTS
was set, no matter if RTS/CTS handshake is enabled or not. Now fixed by
turning handshake on only when CRTSCTS bit for the port is set.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't let receiver hardware automatically control RTS output if it
was requested to be inactive.
To ensure this, set_termios() shouldn't set UCR2_CTSC bit if UCR2_CTS
(=TIOCM_RTS) is cleared. Added corresponding check in imx_uart_rts_auto()
to fix this.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-2-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The established way to provide PM callbacks is through struct dev_pm_ops
which is more generic.
Convert driver to use it instead of legacy approach.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190726172817.73253-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-4-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_ioremap_bar may return null. This is eventually de-referenced at
drivers/dma/dw/core.c:1154 and drivers/dma/dw/core.c:1168. A null check
is needed to prevent null de-reference. I am adding the check and in
case of failure. Thanks to Andy Shevchenko for the hint on the necessity
of pci_iounmap when exiting.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20190719174848.24216-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since .sg_init_one() already set sg entry page like below code.
sg_init_one()
sg_init_table(sg, 1);
sg_set_buf(sg, buf, buflen);
So it should not set sg entry page again, remove the redundant code.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-5-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc() instead of kmalloc() to get clean rx buffer
that is useful for DMA mode debug to check the data moving
validity.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-4-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, .of_dma_configure() init dev.coherent_dma_mask to BIT(32) that
match the eDMA address range. If re-init dev.coherent_dma_mask to zero, then
streaming dma mapping will go swiotlb dma_map, if swiotlb is not initalized
then it causes mapping failed.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array.
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190721150135.82065-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131758.1764-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032001.7212-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many years omap variants have been setting the runtime PM
autosuspend delay to -1 to prevent unsafe policy with lossy first
character on wake-up. The user must specifically enable the timeout
for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads
into UARTs not idling if no serdev devices are loaded and there is no
sysfs entry to configure the UART in that case. And this means that
my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child
node, and we can simply skip the workround in that case. And the
serdev driver can idle the port during runtime when suitable if an
out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20190723115400.46432-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lock down TIOCSSERIAL as that can be used to change the ioport and irq
settings on a serial port. This only appears to be an issue for the serial
drivers that use the core serial code. All other drivers seem to either
ignore attempts to change port/irq or give an error.
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Garrett <mjg59@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-9-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-8-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SGI SN2 support is about to be removed. Remove this driver that
depends on the SN2 support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-7-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
The lpc32xx_loopback_set() function in hte lpc32xx_hs driver is the
one thing that relies on platform header files. Move that into the
core platform code so we only need a variable declaration for it,
and enable COMPILE_TEST building.
Link: https://lore.kernel.org/r/20190809144043.476786-12-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The only thing that prevents building this driver on other
platforms is the mach/hardware.h include, which is not actually
used here at all, so remove the line and allow CONFIG_COMPILE_TEST.
Link: https://lore.kernel.org/r/20190809144043.476786-5-arnd@arndb.de
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After commit ddde3c18b7 ("vt: More locking checks") kdb / kgdb has
become useless because my console is filled with spews of:
WARNING: CPU: 0 PID: 0 at .../drivers/tty/vt/vt.c:3846 con_is_visible+0x50/0x74
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc1+ #48
Hardware name: Rockchip (Device Tree)
Backtrace:
[<c020ce9c>] (dump_backtrace) from [<c020d188>] (show_stack+0x20/0x24)
[<c020d168>] (show_stack) from [<c0a8fc14>] (dump_stack+0xb0/0xd0)
[<c0a8fb64>] (dump_stack) from [<c0232c58>] (__warn+0xec/0x11c)
[<c0232b6c>] (__warn) from [<c0232dc4>] (warn_slowpath_null+0x4c/0x58)
[<c0232d78>] (warn_slowpath_null) from [<c06338a0>] (con_is_visible+0x50/0x74)
[<c0633850>] (con_is_visible) from [<c0634078>] (con_scroll+0x108/0x1ac)
[<c0633f70>] (con_scroll) from [<c0634160>] (lf+0x44/0x88)
[<c063411c>] (lf) from [<c06363ec>] (vt_console_print+0x1a4/0x2bc)
[<c0636248>] (vt_console_print) from [<c02f628c>] (vkdb_printf+0x420/0x8a4)
[<c02f5e6c>] (vkdb_printf) from [<c02f6754>] (kdb_printf+0x44/0x60)
[<c02f6714>] (kdb_printf) from [<c02fa6f4>] (kdb_main_loop+0xf4/0x6e0)
[<c02fa600>] (kdb_main_loop) from [<c02fd5f0>] (kdb_stub+0x268/0x398)
[<c02fd388>] (kdb_stub) from [<c02f3ba0>] (kgdb_cpu_enter+0x1f8/0x674)
[<c02f39a8>] (kgdb_cpu_enter) from [<c02f4330>] (kgdb_handle_exception+0x1c4/0x1fc)
[<c02f416c>] (kgdb_handle_exception) from [<c0210fe0>] (kgdb_compiled_brk_fn+0x30/0x3c)
[<c0210fb0>] (kgdb_compiled_brk_fn) from [<c020d7ac>] (do_undefinstr+0x180/0x1a0)
[<c020d62c>] (do_undefinstr) from [<c0201b44>] (__und_svc_finish+0x0/0x3c)
...
[<c02f3224>] (kgdb_breakpoint) from [<c02f3310>] (sysrq_handle_dbg+0x58/0x6c)
[<c02f32b8>] (sysrq_handle_dbg) from [<c062abf0>] (__handle_sysrq+0xac/0x154)
Let's disable this warning when we're in kgdb to avoid the spew. The
whole system is stopped when we're in kgdb so we can't exactly wait
for someone else to drop the lock. Presumably the best we can do is
to disable the warning and hope for the best.
Fixes: ddde3c18b7 ("vt: More locking checks")
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190725183551.169208-1-dianders@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Netx ARM machine was deleted from the kernel. This driver
had no users and has to go.
Cc: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190722065146.4844-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus Walleij--
the SoC doesn't have active maintainers with hardware, and in
discussions with the vendor the agreement was that it's OK to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support.
-----BEGIN PGP SIGNATURE-----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=FX6e
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC platform changes. Main theme this merge window:
- The Netx platform (Netx 100/500) platform is removed by Linus
Walleij-- the SoC doesn't have active maintainers with hardware,
and in discussions with the vendor the agreement was that it's OK
to remove.
- Russell King has a series of patches that cleans up and refactors
SA1101 and RiscPC support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
ARM: stm32: use "depends on" instead of "if" after prompt
ARM: sa1100: convert to common clock framework
ARM: exynos: Cleanup cppcheck shifting warning
ARM: pxa/lubbock: remove lubbock_set_misc_wr() from global view
ARM: exynos: Only build MCPM support if used
arm: add missing include platform-data/atmel.h
ARM: davinci: Use GPIO lookup table for DA850 LEDs
ARM: OMAP2: drop explicit assembler architecture
ARM: use arch_extension directive instead of arch argument
ARM: imx: Switch imx7d to imx-cpufreq-dt for speed-grading
ARM: bcm: Enable PINCTRL for ARCH_BRCMSTB
ARM: bcm: Enable ARCH_HAS_RESET_CONTROLLER for ARCH_BRCMSTB
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
MAINTAINERS: mvebu: Add git entry
soc: ti: pm33xx: Add a print while entering RTC only mode with DDR in self-refresh
ARM: OMAP2+: Make some variables static
...
* 'for-arm-soc' of git://git.armlinux.org.uk/~rmk/linux-arm: (21 commits)
ARM: sa1100: convert to common clock framework
ARM: riscpc: enable chained scatterlist support
ARM: riscpc: reduce IRQ handling code
ARM: riscpc: move RiscPC assembly files from arch/arm/lib to mach-rpc
ARM: riscpc: parse video information from tagged list
ARM: riscpc: add ecard quirk for Atomwide 3port serial card
ARM: sa1100/neponset: convert serial to use gpiod APIs
ARM: sa1100/hackkit: remove empty serial mctrl functions
ARM: sa1100/badge4: remove commented out modem control initialisers
ARM: sa1100/h3xxx: convert serial to gpiod APIs
ARM: sa1100/assabet: convert serial to gpiod APIs
serial: sa1100: add note about modem control signals
serial: sa1100: add support for mctrl gpios
ARM: riscpc: dma: use __iomem pointers for writing DMA
ARM: riscpc: dma: improve address/length writing
ARM: riscpc: dma: make state a local variable
ARM: riscpc: dma: eliminate "cur_sg" scatterlist usage
ARM: riscpc: fix DMA
ARM: riscpc: fix ecard printing
ARM: riscpc: fix lack of keyboard interrupts after irq conversion
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Converts ARM the text files to ReST, preparing them to be an
architecture book.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by Corentin Labbe <clabbe.montjoie@gmail.com> # For sun4i-ss
Pull sparc updates from David Miller:
"Just a few small changes:
- Fix console naming inconsistency with hypervisor consoles, from
John Paul Adrian Glaubitz
- Fix userland compilation due to use of u_int, from Masahiro Yamada"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Add missing newline at end of file
sparc: fix unknown type name u_int in uapi header
sparc: configs: Remove useless UEVENT_HELPER_PATH
sparc: Remove redundant copy of the LGPL-2.0
sunhv: Fix device naming inconsistency between sunhv_console and sunhv_reg
The lpuart of imx8ulp is basically the same as imx7ulp, but it
has new feature support based on imx7ulp, like it can assert a
DMA request on EOP(end-of-packet). imx8ulp lpuart use two clocks,
one is ipg bus clock that is used to access registers, the other
is baud clock that is used to transmit-receive data.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190704134007.2316-1-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid repeating the same code for rs485 twice.
Make it obvious we clear CRTSCTS bit in termios->c_cflag whenever
sport->have_rtscts is false.
Make it obvious we clear UCR2_IRTS whenever CRTSCTS is set.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1561558293-7683-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set common bits in a separate statement to make initialization
explicit and not repeat the common part.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1561558293-7683-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the .flush_buffer() callback clears sci_port.tx_dma_len since
commit 1cf4a7efdc ("serial: sh-sci: Fix race condition causing
garbage during shutdown"), it does not terminate a transmit DMA
operation that may be in progress.
Fix this by terminating any pending DMA operations, and resetting the
corresponding cookie.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uart_flush_buffer() is called, the .flush_buffer() callback zeroes
the tx_dma_len field. This may race with the work queue function
handling transmit DMA requests:
1. If the buffer is flushed before the first DMA API call,
dmaengine_prep_slave_single() may be called with a zero length,
causing the DMA request to never complete, leading to messages
like:
rcar-dmac e7300000.dma-controller: Channel Address Error happen
and, with debug enabled:
sh-sci e6e88000.serial: sci_dma_tx_work_fn: ffff800639b55000: 0...0, cookie 126
and DMA timeouts.
2. If the buffer is flushed after the first DMA API call, but before
the second, dma_sync_single_for_device() may be called with a zero
length, causing the transmit data not to be flushed to RAM, and
leading to stale data being output.
Fix this by:
1. Letting sci_dma_tx_work_fn() return immediately if the transmit
buffer is empty,
2. Extending the critical section to cover all DMA preparational work,
so tx_dma_len stays consistent for all of it,
3. Using local copies of circ_buf.head and circ_buf.tail, to make sure
they match the actual operation above.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Suggested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-2-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for the Marvell MV64x60 line of bridge chips that contained
MPSC controllers has been removed and there are no other components
that have that controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Link: https://lore.kernel.org/r/20190626160553.28518-1-mgreer@animalcreek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing unlock before return from function serial8250_register_8250_port()
in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190703055908.141294-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a flush of RX and TX FIFOs, and fixes some errors:
- adds RX FIFO flush in startup fonction
- removes the useless transmitter enabling in startup fonction
(e.g. receiver only, see Documentation/serial/driver)
- configures FIFO threshold before enabling it, rather than after
- flushes both TX and RX in set_termios function
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of RX FIFO threshold in order to improve the RX FIFO
management.
This is done by enabling fifo threshold interrupt, instead of relying
on rx empty/fifo not full irq. That basically generates one irq/char
currently. With this patch:
- RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current
RXCFG setting.
- Receiver timeout is used to gather chars when FIFO threshold isn't
reached.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of TX FIFO threshold in order to improve the TX FIFO
management:
- TX FIFO threshold irq enabling (instead of relying on tx empty / fifo
not full irq that generates one irq/char)
- TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current
TXCFG setting.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improves PIO transmission:
- Replaces the FIFO filling per character by a filling per blocks of
characters, which provides better performances
- Replaces the active waiting loop by TX empty interrupt dynamic handling.
TXE interrupt is now enabled when data has to be sent (ie when
uart_circ is not empty), and inhibited when there is no more data to
send (ie when uart_circ is empty).
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of RX timeout interrupts to limit the number of interrupts.
RX timeout is a number of bits (baud clock cycles) without
transmission seen in the receiver. One character is used as an arbitrary
RX timeout value.
If parity is enabled, the number of bits has to include parity bit.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check for the GPIOs property existence, before the
GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio
support is added (2nd patch in this patch series) on x86 platforms using
ACPI.
Here Mika's comments from 2016-08-09:
"
I noticed that with v4.8-rc1 serial console of some of our Broxton
systems does not work properly anymore. I'm able to see output but input
does not work.
I bisected it down to commit 4ef03d3287
("tty/serial/8250: use mctrl_gpio helpers").
The reason why it fails is that in ACPI we do not have names for GPIOs
(except when _DSD is used) so we use the "idx" to index into _CRS GPIO
resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs
calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The
UART device in Broxton has following (simplified) ACPI description:
Device (URT4)
{
...
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003A
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003D
}
})
In this case it finds the first GPIO (0x003A which happens to be RX pin
for that UART), turns it into GPIO which then breaks input for the UART
device. This also breaks systems with bluetooth connected to UART (those
typically have some GPIOs in their _CRS).
Any ideas how to fix this?
We cannot just drop the _CRS index lookup fallback because that would
break many existing machines out there so maybe we can limit this to
only DT enabled machines. Or alternatively probe if the property first
exists before trying to acquire the GPIOs (using
device_property_present()).
"
This patch implements the fix suggested by Mika in his statement above.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug was introduced by commit b3b5764618 ("tty: serial_core: convert
uart_open to use tty_port_open"). It caused a constant warning printed
into the system log regarding the tty and port counter mismatch:
[ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2
in case if session hangup was detected so the warning is printed starting
from the second open-close iteration.
Particularly the problem was discovered in situation when there is a
serial tty device without hardware back-end being setup. It is considered
by the tty-serial subsystems as a hardware problem with session hang up.
In this case uart_startup() will return a positive value with TTY_IO_ERROR
flag set in corresponding tty_struct instance. The same value will get
passed to be returned from the activate() callback and then being returned
from tty_port_open(). But since in this case tty_port_block_til_ready()
isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been
called before tty_port_open conversion was introduced and the rest of the
subsystem code expected the bit being set in this case), which prevents the
uart_hangup() method to perform any cleanups including the tty port
counter setting to zero. So the next attempt to open/close the tty device
will discover the counters mismatch.
In order to fix the problem we need to manually set the TTY_PORT_ACTIVE
flag in case if uart_startup() returned a positive value. In this case
the hang up procedure will perform a full set of cleanup actions including
the port ref-counter resetting.
Fixes: b3b5764618 "tty: serial_core: convert uart_open to use tty_port_open"
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds wrapper functions to convert MSR <-> TIOCM and also
MCR <-> TIOCM. These functions are used now in serial8250_do_set_mctrl()
and serial8250_do_get_mctrl().
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out similar code pieces that set or clear UART_IER_THRI bit to
serial8250_{set,clear}_THRI() helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to add an out-of-memory error message inside
the driver because the core MM code will take care of it.
Remove the unneeded OOM error message.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to call return at the end of function which should
return void.
The patch is also remove one checkpatch warning:
WARNING: void function return statements are not generally useful
+ return;
+}
Fixes: 6ee04c6c54 ("tty: xuartps: Add polled mode support for xuartps")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes this checkpatch warning:
WARNING: macros should not use a trailing semicolon
+#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
+ clk_rate_change_nb);
Fixes: d9bb3fb126 ("tty: xuartps: Rebrand driver as Cadence UART")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let kernel to find out major number dynamically for the first device and
then reuse it for other instances.
This fixes the issue that each uart is registered with a
different major number.
After the patch:
crw------- 1 root root 253, 0 Jun 10 08:31 /dev/ttyPS0
crw--w---- 1 root root 253, 1 Jan 1 1970 /dev/ttyPS1
Fixes: 024ca329bf ("serial: uartps: Register own uart console and driver structures")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Pericom chips can achieve additional baud rates by programming the
sample clock register. The baud rates can be described as
921600 * 16 / (16 - scr) for scr values 5 to 15. The divisor is set to 1
for these baud rates.
Adds new quirk for Pericom chips other than the four port chips to use
the
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_uart_set_termios() called imx_uart_rts_active(), or
imx_uart_rts_inactive() before taking port->port.lock.
As a consequence, sport->port.mctrl that these functions modify
could have been changed without holding port->port.lock.
Moved locking of port->port.lock above the calls to fix the issue.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In d5a2aa24, the name in struct console sunhv_console was changed from "ttyS"
to "ttyHV" while the name in struct uart_ops sunhv_pops remained unchanged.
This results in the hypervisor console device to be listed as "ttyHV0" under
/proc/consoles while the device node is still named "ttyS0":
root@osaka:~# cat /proc/consoles
ttyHV0 -W- (EC p ) 4:64
tty0 -WU (E ) 4:1
root@osaka:~# readlink /sys/dev/char/4:64
../../devices/root/f02836f0/f0285690/tty/ttyS0
root@osaka:~#
This means that any userland code which tries to determine the name of the
device file of the hypervisor console device can not rely on the information
provided by /proc/consoles. In particular, booting current versions of debian-
installer inside a SPARC LDOM will fail with the installer unable to determine
the console device.
After renaming the device in struct uart_ops sunhv_pops to "ttyHV" as well,
the inconsistency is fixed and it is possible again to determine the name
of the device file of the hypervisor console device by reading the contents
of /proc/console:
root@osaka:~# cat /proc/consoles
ttyHV0 -W- (EC p ) 4:64
tty0 -WU (E ) 4:1
root@osaka:~# readlink /sys/dev/char/4:64
../../devices/root/f02836f0/f0285690/tty/ttyHV0
root@osaka:~#
With this change, debian-installer works correctly when installing inside
a SPARC LDOM.
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c70669ecef as it
breaks the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Bich Hemon <bich.hemon@st.com>
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function msm_wait_for_xmitr can be taken with interrupts
disabled. In order to avoid a potential system lockup - demonstrated
under stress testing conditions on SoC QCS404/5 - make sure we wait
for a bounded amount of time.
Tested on SoC QCS404.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support Rx in-band wakeup, we need to enable irq wake on an
edge sensitive interrupt of Rx pin before suspend and disable it when
resuming.
This interrupt is used only as wake source to resume the system when
suspended. Note that the sent character will be lost as the controller is
actually suspended.
We use this to support wakeup on bluetooth. Bluetooth will repeatedly send
0xFD to wakeup host. Once host detects Rx falling, an interrupt is
triggered, and the system leaves sleep state. Then, the bluetooth driver
will send 0xFC to bluetooth and bluetooth can start to send normal HCI
packets.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the cable is not connected then the target gets into
an infinite wait for tx empty.
Add a timeout to the tx empty wait.
Reported-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are doing a read of the status register.
Move the spinlock after that as the reads need not be spinlock
protected. This patch prevents relaxing the cpu with spinlock held.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe/rmmod/modprobe module, if platform_driver_register() fails,
the kernel complained,
proc_dir_entry 'driver/digicolor-usart' already registered
WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270
Fix this by adding uart_unregister_driver() when platform_driver_register() fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/stm32-usart.c:603:14: warning:
symbol 'stm32_get_databits' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by Uwe, add a note indicating that the modem control
signals do not support interrupts, which precludes the driver from
using mctrl_gpio_init().
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support for the generic mctrl gpio helper. This will allow us to
convert several board files to use the gpiod tables to assign GPIOs to
serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather
than preventing the (possibly console) serial port from being created.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Drop the RELEVANT_IFLAG() macro which hasn't been used at least since
the dawn of git.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SMC relocation can also be activated earlier by the bootloader,
so the driver's behaviour cannot rely on selected kernel config.
When the SMC is relocated, CPM_CR_INIT_TRX cannot be used.
But the only thing CPM_CR_INIT_TRX does is to clear the
rstate and tstate registers, so this can be done manually,
even when SMC is not relocated.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9ab9212014 ("cpm_uart: fix non-console port startup bug")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checks the returned values of platform_get_irq() for both required
"event" and optional "wakeup" IRQs during probe. This allows the driver
probe to be deferred if needed.
Removes redundant checks for 'cfg.has_wakeup'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disables the tx irq when the transmission is ended and updates stop_tx
conditions for code cleanup.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet states:
Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in commit 84b40e3b57 ("serial: 8250: omap: Disable DMA for
console UART"), UART console lines use low-level PIO only access functions
which will conflict with use of the line when DMA is enabled, e.g. when
the console line is also used for systemd messages. So disable DMA
support for UART console lines.
Reported-by: Michael Rodin <mrodin@de.adit-jv.com>
Link: https://patchwork.kernel.org/patch/10929511/
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
Fixes: 68252424a7 ("tty: serial: msm: Support big-endian CPUs")
Cc: stable@vger.kernel.org
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Batch read mode doesn't check any conditions or flags except the Rx
overflow one. But it may only happen after the last character is pushed
into the RHR register. In this case we shouldn't push all the read
characters with overrun flag set, but only the last one caused the
FIFO overflow. This commit splits the characters retrieval loop into
two parts. First one is ordinary intsert-chars procedure without taking
the overrun status into account. Second part inserts the last character
checking whether the overrun happened and pushing a '\0' character with
TTY_OVERRUN flag to a flip-buffer.
If we left the loop the way it was the '\0' character would be inserted
after each character retrieved at the overrun occasion.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART port might be pre-configured with rs485 enabled flag at the
time of the port starting up process. In this case we need to
have the hardware rs485-related registers initialized in accordance
with the rs485 flags and settings provided by the configs descriptor.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently sets the echo suppression bit by default when rs485
is enabled. Naturally it disables any data retrieval in rs485 mode while
RTSn is pushed up. The receiver gate (RX_) can be enabled just by clearing
(or not setting) the EchoSuprs bit of mode2 register. So by setting or
clearing the bit we implement the SER_RS485_RX_DURING_TX rs485 flag
support.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current calculator doesn't do it' job quite correct. First of all the
max310x baud-rates generator supports the divisor being less than 16.
In this case the x2/x4 modes can be used to double or quadruple
the reference frequency. But the current baud-rate setter function
just filters all these modes out by the first condition and setups
these modes only if there is a clocks-baud division remainder. The former
doesn't seem right at all, since enabling the x2/x4 modes causes the line
noise tolerance reduction and should be only used as a last resort to
enable a requested too high baud-rate.
Finally the fraction is supposed to be calculated from D = Fref/(c*baud)
formulae, but not from D % 16, which causes the precision loss. So to speak
the current baud-rate calculator code works well only if the baud perfectly
fits to the uart reference input frequency.
Lets fix the calculator by implementing the algo fully compliant with
the fractional baud-rate generator described in the datasheet:
D = Fref / (c*baud), where c={16,8,4} is the x1/x2/x4 rate mode
respectively, Fref - reference input frequency. The divisor fraction is
calculated from the same formulae, but making sure it is found with a
resolution of 0.0625 (four bits).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI transfer tx/rx buffers must be DMA-safe and the structure
documentation clearly states this. Data declared on the system stack isn't
DMA-safe [1]. Instead at least kernel memory should be used for the
buffers. In order to fix this here we can create the buffers at the device
probing stage and use them without any synchronization, since batch
read/write methods are called from non-reentrant contexts - either from
rx-event IRQ threaded handler or from the tx workqueue item.
[1] Documentation/DMA-API-HOWTO.txt
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_port structure instance is embedded into the max310x_one
super-structure, which is accessed by some of the uart-port callback
methods. In order to improve the callback's code readability lets
define the to_max310x_port() wrapper which just translates the passed
uart_port pointer to the max310x_one one. It is also going to be
handy in future commits.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since cmwq introduction in the kernel, workqueues've been turned into
non-reentrant execution contexts [1]. It means any work item is
guaranteed to be executed by at most one worker system-wide at any
given time. Since tx-handler max310x_handle_tx() is called by a
single work item we don't need it to be self-protected by the mutex.
We also don't need to check the tx work item pending state before
scheduling it (which in the first place was racy btw), since cmwq will
make sure to reschedule the item if it wasn't pending at the moment of
schedule_work() call.
[1] Documentation/core-api/workqueue.rst
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PL011 register space includes all necessary status bits to
determine whether a device instance requires handling in response
to an interrupt. Therefore, multiple instances of the device could
be serviced by a single shared interrupt, which is the case on BCM7211.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_dbg statement should print the value of uart.port.mapbase instead
of its address. Besides that, uart.port.irq and uart.port.iotype are all
unsigned types, so using %u is more appropriate.
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_device_get_match_data() to simplify the code a bit.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJc08p1AAoJEHwUBw8lI4NHD14QAJGU7MOc9dpr+qtm2k3sNO3o
EXZtb3GjTs4MUt6EfMA47KXsxeq4UhubQqM7CmPngDyjXaPd4JBE8bwAd+OzS9sq
eAPMa+M1g8MehuQcdUzB/y6APoSFhGvFoGLY8e7FeI6fwYNm3Yy2gTSiZfpMb3MW
hclJQe+UWfppUHOig13tr0tbQ31DOa7qb2+roVJqDEb9sQ5bDkhRWXjElfoeSXsS
n8nNh4GZr5RkIxfzslVRZNfqb1lja2e03SXBsN9faQI7BfIYBM+9hWSYd4Nq8uYo
xvhYf9gJnKVKtFrwdXtyeBJ80DijWBoodhLrLOfhEYYOrCl9WwJT9AepIOdvij32
11FwjCbkC9ASQ1cSLyRUBbdmfykSlBvdbAMwJc1y9qK7k9BMba3rXRJfimlRy29A
Cpsu4tZKoPlZRGinoGnEGreg1YZI1YHwa+hlkW/8V9Zkb2hvIUbbXr7xHedJf7n4
gIb5DnCF5pC1umB/o7pj2YXrYBc9GETp3sDQ88aw1owKh1T2pZcc5HOpi4p7/7n+
b2HM0cWOCM3aKwdOcONk0jd87FcYQm3g1isQF5SCOtOys8Uy6wNqo9aRrfE/94aw
4SiGRq9/nSOHDh72mD3Ux7v47/cFjWGzZZJVy5+NC+Mq79KxgpXOjsIr7YVbcn9m
GuUdiDZmUvZ4y+qq/uCI
=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKvrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynR2wCfTrWM9Qm7oA1hgWeYZiLTrnYnOtsAoK4a629W
o7AAyVf8RJ4jdWaSgOqx
=9Dy/
-----END PGP SIGNATURE-----
Merge tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.2-rc1.
It's really pretty small, not much happening in this portion of the
kernel at the moment. When the "highlight" is the movement of the
documentation from .txt to .rst files, it's a good merge window.
There's a number of small fixes and updates over the various serial
drivers, and a new "tty null" driver for those embedded systems that
like to make things even smaller and not break things.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (45 commits)
tty: serial: add driver for the SiFive UART
dt-bindings: serial: add documentation for the SiFive UART driver
serial: uartps: Add support for cts-override
dt-bindings: xilinx-uartps: Add support for cts-override
serial: milbeaut_usio: Fix error handling in probe and remove
tty: rocket: deprecate the rp_ioctl
tty: rocket: Remove RCPK_GET_STRUCT ioctl
tty: update obsolete termios comment
tty: serial_core: fix error code returned by uart_register_driver()
serial: 8250-mtk: modify baudrate setting
serial: 8250-mtk: add follow control
docs: serial: convert docs to ReST and rename to *.rst
serial: 8250_exar: Adjust IOT2000 matching
TTY: serial_core, add ->install
serial: Fix using plain integer instead of Null pointer
tty:serial_core: Spelling mistake
tty: Add NULL TTY driver
tty: vt: keyboard: Allow Unicode compose base char
Revert "tty: fix NULL pointer issue when tty_port ops is not set"
serial: Add Milbeaut serial control
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Add a serial driver for the SiFive UART, found on SiFive FU540 devices
(among others).
The underlying serial IP block is relatively basic, and currently does
not support serial break detection. Further information on the IP
block can be found in the documentation and Chisel sources:
https://static.dev.sifive.com/FU540-C000-v1.0.pdfhttps://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/uart
This driver was written in collaboration with Wesley Terpstra
<wesley@sifive.com>.
Tested on a SiFive HiFive Unleashed A00 board, using BBL and the open-
source FSBL (using a DT file based on what's targeted for mainline).
This revision incorporates changes based on comments by Julia Lawall
<julia.lawall@lip6.fr>, Emil Renner Berthing <kernel@esmil.dk>, and
Andreas Schwab <schwab@suse.de>. Thanks also to Andreas for testing
the driver with his userspace and reporting a bug with the
set_termios implementation.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having flow is configurable. Add support for the same by
checking for cts-override.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() is used so there is no reason to explicitly call
clk_put() in probe or remove functions. Also remove duplicate assign
for port->membase.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver() returned -ENOMEM on any error, even when
tty_register_driver() call returned another one, such as -EBUSY.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SW and HW follow control function.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converted files are focused at the Kernel internal API,
so, this is a good candidate for the kernel API set of books.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
As only the IOT2040 variants have the Exar chip on board, matching on
their board name is enough. In the future there will be no other devices
with the "SIMATIC IOT2000" DMI board name but different hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to compute the uart state only on the first open. This is
usually what is done in the ->install hook. serial_core used to do this
in ->open on every open. So move it to ->install.
As a side effect, it ensures the state is set properly in the window
after tty_init_dev is called, but before uart_open. This fixes a bunch
of races between tty_open and flush_to_ldisc we were dealing with
recently.
One of such bugs was attempted to fix in commit fedb576064 (serial:
fix race between flush_to_ldisc and tty_open), but it only took care of
a couple of functions (uart_start and uart_unthrottle). I was able to
reproduce the crash on a SLE system, but in uart_write_room which is
also called from flush_to_ldisc via process_echoes. I was *unable* to
reproduce the bug locally. It is due to having this patch in my queue
since 2012!
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 5 Comm: kworker/u4:0 Tainted: G L 4.12.14-396-default #1 SLE15-SP1 (unreleased)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
task: ffff8800427d8040 task.stack: ffff8800427f0000
RIP: 0010:uart_write_room+0xc4/0x590
RSP: 0018:ffff8800427f7088 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000002f RSI: 00000000000000ee RDI: ffff88003888bd90
RBP: ffffffffb9545850 R08: 0000000000000001 R09: 0000000000000400
R10: ffff8800427d825c R11: 000000000000006e R12: 1ffff100084fee12
R13: ffffc900004c5000 R14: ffff88003888bb28 R15: 0000000000000178
FS: 0000000000000000(0000) GS:ffff880043300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000561da0794148 CR3: 000000000ebf4000 CR4: 00000000000006e0
Call Trace:
tty_write_room+0x6d/0xc0
__process_echoes+0x55/0x870
n_tty_receive_buf_common+0x105e/0x26d0
tty_ldisc_receive_buf+0xb7/0x1c0
tty_port_default_receive_buf+0x107/0x180
flush_to_ldisc+0x35d/0x5c0
...
0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is
tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at
uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount
used in uart_port_lock from uart_write_room.
So revert the upstream commit here as my local patch should fix the
whole family.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Li RongQing <lirongqing@baidu.com>
Cc: Wang Li <wangli39@baidu.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning that using plain integer as Null pointer.
This is reported by kbuild test robot.
Fixes: ba44dc0430 ("serial: Add Milbeaut serial control")
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of the sampling point has min() and max() exchanged.
Fix this by using the clamp() helper instead.
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Milbeaut serial control including earlycon and console.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There were a few straggling files under drivers/tty/ that did not have
any SPDX identifier either because they entered the tree recently, or
they somehow missed the mass-tagging of commit b24413180f ("License
cleanup: add SPDX GPL-2.0 license identifier to files with no license")
This commit follows the same rule as b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license") where files
without any specified license in them fall under GPL-2.0 as the correct
license for the individual file. Add that identifier to these remaining
files so that we don't have to guess at the license of them in the
future.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a few Kconfig and Makefiles under drivers/tty/ that were
missing a SPDX identifier. Fix that up so that automated tools can
properly classify all kernel source files.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open coded variants, switch to direct use of
device_get_match_data().
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the property is provided and there are no other possibilities to detect
UART clock frequency, use it as a fallback.
Tested-By: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DMA mode support for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds power management for the Spreadtrum serial controller.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/8250/8250_fintek.c:306:6: warning:
symbol 'fintek_8250_set_termios' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes: b389f173aa ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/tty/serial/qcom_geni_serial.c:1079:6: warning: variable 'baud'
is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
It's not wrong; when options is NULL, baud has no default value. Use
9600 as that is a sane default.
Link: https://github.com/ClangBuiltLinux/linux/issues/395
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereferences.
Multiple places use port.membase.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device on failure to find a matching device can return a NULL
pointer. The patch checks for such a scenrio and passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Existing driver checks for alternate clock if devm_clk_get() fails
and returns error code for last clock failure. If xilinx_uartps is
called before clock driver, devm_clk_get() returns -EPROBE_DEFER.
In this case, probe should not check for alternate clock as main
clock is already present in DTS and return -EPROBE_DEFER only.
This patch fixes it by not checking for alternate clock when main
clock get returns -EPROBE_DEFER.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the source clock is not divisible by the expected baud rate and
the remainder is not less than half of the expected baud rate, the old
formular will round up the frequency division coefficient. This will
make the actual baud rate less than the expected value and can not meet
the external transmission requirements.
Thus this patch modifies the baud rate calculation formula to support
the serial controller output the maximum baud rate.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two other drivers that bind to mrvl,mmp-uart and both of them
assume register shift of 2 bits. There are device trees that lack the
property and rely on that assumption.
If this driver wins the race to bind to those devices, it should behave
the same as the older deprecated driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the other OF-enabled drivers, use the port number from the firmware if
the devicetree specifies an alias:
aliases {
...
serial2 = &uart2; /* Should be ttyS2 */
}
This is how the deprecated pxa.c driver behaved, switching to 8250_pxa
messes up the numbering.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the complexities of modern Qualcomm SoCs, about a half dozen drivers
must successfully probe before the clocks for the console are present, and
the console can successfully probe. Depending on several random factors
such as probe order and modules vs builtin, msm_serial may not be able to
successfully probe for some, at which point, __init annotated functions
may become unmapped. If this occurs, msm_console_setup() will be called
from the probe path, but will no longer exist, resulting in a kernel
panic.
Resolve this issue by removing the __init annotation from
msm_console_setup().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exynos 5260, like the 5433, appears to require baud clock as
well as pclk to be running before accessing any of the registers,
otherwise an external abort is raised.
The serial driver already enables baud clock when required, but only
if it knows which clock is baud clock. On older SoCs baud clock may be
selected from a number of possible clocks so to support this the driver
only selects which clock to use for baud clock when a port is opened,
at which point the desired baud rate is known and the best clock can be
selected.
The result is that there are a number of circumstances in which
registers are accessed without first explicitly enabling baud clock:
- while the driver is being initialised
- the initial parts of opening a port for the first time
- when resuming if the port hasn't been already opened
The 5433 overcomes this currently by marking the baud clock as
CLK_IGNORE_UNUSED, so the clock is always enabled, however
for the 5260 I've been trying to avoid this.
This change adds code to pick the first available clock to use
as baud clock and enables it while initialising the driver.
This code wouldn't be sufficient on a SoC which supports
multiple possible baud clock sources _and_ requires the
correct baud clock to be enabled before accessing any of the
serial port registers (in particular the register which selects
which clock to use as the baud clock). As far as I know
such hardware doesn't exist.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RX is disabled while there are still unprocessed bytes in RX FIFO,
cdns_uart_handle_rx() called from interrupt handler will get stuck in
the receive loop as read bytes will not get removed from the RX FIFO
and CDNS_UART_SR_RXEMPTY bit will never get set.
Avoid the stuck handler by checking first if RX is disabled. port->lock
protects against race with RX-disabling functions.
This HW behavior was mentioned by Nathan Rossi in 43e98facc4a3 ("tty:
xuartps: Fix RX hang, and TX corruption in termios call") which fixed a
similar issue in cdns_uart_set_termios().
The behavior can also be easily verified by e.g. setting
CDNS_UART_CR_RX_DIS at the beginning of cdns_uart_handle_rx() - the
following loop will then get stuck.
Resetting the FIFO using RXRST would not set RXEMPTY either so simply
issuing a reset after RX-disable would not work.
I observe this frequently on a ZynqMP board during heavy RX load at 1M
baudrate when the reader process exits and thus RX gets disabled.
Fixes: 61ec901698 ("tty/serial: add support for Xilinx PS UART")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unlikely has already included in IS_ERR(),
so just remove redundant likely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four port Pericom chips have the fourth port at the wrong address.
Make use of quirk to fix it.
Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Have the correct number of ports created for ACCES serial cards. Two port
cards show up as four ports, and four port cards show up as eight.
Fixes: c8d192428f ("serial: 8250: added acces i/o products quad and octal serial cards")
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_pci_is_blacklisted() is very similar to pci_match_id() implementation.
Replace it with the latter.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXF09tg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yniTwCfQ9Owr8XFJRW7QC0BPKDjohqewA8AniK/9YJ/
l73fnvsXELOX9eE/ixCx
=0ylh
-----END PGP SIGNATURE-----
Merge tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: fix race between flush_to_ldisc and tty_open
staging: speakup: fix tty-operation NULL derefs
serial: sh-sci: Do not free irqs that have already been freed
serial: 8250_pci: Make PCI class test non fatal
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
The MODE1 register bits have different values for different ICs.
This patch corrects the initial setting of this register in accordance
with the datasheets, which will allow you to get the expected values
when debugging the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch set contains a handful of mostly-independent patches:
* A patch that causes our port to respect TIF_NEED_RESCHED, which fixes
CONFIG_PREEMPT=y kernels.
* A fix to avoid double-put on OF nodes.
* Fix a misspelling of target in our Kconfig.
* Generic PCIe is enabled in our defconfig.
* A fix to our SBI early console to properly handle line endings.
* A fix such that max_low_pfn is counted in PFNs.
* A change to TASK_UNMAPPED_BASE to match what other arches do.
This has passed by standard "boot Fedora" flow.
-----BEGIN PGP SIGNATURE-----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=Z3YY
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of mostly-independent patches:
- make our port respect TIF_NEED_RESCHED, which fixes
CONFIG_PREEMPT=y kernels
- fix double-put of OF nodes
- fix a misspelling of target in our Kconfig
- generic PCIe is enabled in our defconfig
- fix our SBI early console to properly handle line
endings
- fix max_low_pfn being counted in PFNs
- a change to TASK_UNMAPPED_BASE to match what other
arches do
This has passed my standard 'boot Fedora' flow"
* tag 'riscv-for-linus-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
riscv: Adjust mmap base address at a third of task size
riscv: fixup max_low_pfn with PFN_DOWN.
tty/serial: use uart_console_write in the RISC-V SBL early console
RISC-V: defconfig: Add CRYPTO_DEV_VIRTIO=y
RISC-V: defconfig: Enable Generic PCIE by default
RISC-V: defconfig: Move CONFIG_PCI{,E_XILINX}
RISC-V: Kconfig: fix spelling mistake "traget" -> "target"
RISC-V: asm/page.h: fix spelling mistake "CONFIG_64BITS" -> "CONFIG_64BIT"
RISC-V: fix bad use of of_node_put
RISC-V: Add _TIF_NEED_RESCHED check for kernel thread when CONFIG_PREEMPT=y
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
There still is a race window after the commit b027e2298b
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
CPU0 CPU1
---- ----
tty_open
tty_init_dev
tty_ldisc_unlock
schedule
flush_to_ldisc
receive_buf
tty_port_default_receive_buf
tty_ldisc_receive_buf
n_tty_receive_buf_common
__receive_buf
uart_flush_chars
uart_start
/*tty->driver_data is NULL*/
tty->ops->open
/*init tty->driver_data*/
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com>
Tested-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/tty/serial/mps2-uart.c:351:6: warning: logical not is only
applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^ ~
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses after the
'!' to evaluate the bitwise operator first
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
drivers/tty/serial/mps2-uart.c:351:6: note: add parentheses around left
hand side expression to silence this warning
if (!mps_port->flags & UART_PORT_COMBINED_IRQ) {
^
( )
1 warning generated.
As it was intended for this check to be the inverse of the one at the
bottom of mps2_init_port, add parentheses around the whole conditional.
Fixes: 775ea4ea2f ("serial: mps2-uart: support combined irq")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/344
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that some designs went for implementing only combined
interrupt for rx, tx and overrun, which is currently not supported
by the driver. Support of combined irq is built on top of existent
irq handlers and activated automatically if only single irq was
specified in device tree.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some designs, like MPS3, expose number of virtual serial ports which
already close or exceeds MPS2_MAX_PORTS. Increasing MPS2_MAX_PORTS
would have negative impact (in terms of memory consumption) on tiny
MPS2 platform which, in fact, has only one physically populated UART.
Start with converting existent static port array to idr. As a bonus it
make driver not to fail in case when no alias was specified in device
tree.
Note: there is no need in idr_destroy() because code doesn't unload
since ce87122911 ("serial: mps2-uart: make driver explicitly non-modular")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae7 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As has been reported the National Instruments serial cards have broken
PCI class.
The commit 7d8905d064
("serial: 8250_pci: Enable device after we check black list")
made the PCI class check mandatory for the case when device is listed in
a quirk list.
Make PCI class test non fatal to allow broken card be enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Cc: stable <stable@vger.kernel.org>
Reported-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: Guan Yung Tseng <guan.yung.tseng@ni.com>
Tested-by: KHUENY.Gerhard <Gerhard.KHUENY@bachmann.info>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on data->dma
This bug was detected with the help of Coccinelle.
Fixes: 85b5c1dd04 ("serial: 8250-mtk: add uart DMA support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra Combined UART (TCU) is a mailbox-based mechanism that allows
multiplexing multiple "virtual UARTs" into a single hardware serial
port. The TCU is the primary serial port on Tegra194 devices.
Add a TCU driver utilizing the mailbox framework, as the used mailboxes
are part of Tegra HSP blocks that are already controlled by the Tegra
HSP mailbox driver.
Based on work by Mikko Perttunen <mperttunen@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the 8250_ingenic driver on the
X1000 Soc from Ingenic.
Signed-off-by: Zhou Yanjie <zhouyanjie@zoho.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for device tree probing for the Intel
Xscale 8250 variant needed to support device tree on
the Intel IXP4xx platforms.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DMA support for 32-bit variant of the LPUART, such as LS1021A.
Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The geni set/get_mctrl() functions currently do nothing unless
hardware flow control is enabled. Remove this arbitrary limitation.
Suggested-by: Johan Hovold <johan@kernel.org>
Fixes: 8a8a66a1a1 ("tty: serial: qcom_geni_serial: Add support for flow control")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initialization code of interrupt backoff work might reference NULL
pointer and cause the following crash, if no port was found.
[ 10.017727] CPU 0 Unable to handle kernel paging request at virtual address 000001b0, epc == 807088e0, ra == 8070863c
---- snip ----
[ 11.704470] [<807088e0>] serial8250_register_8250_port+0x318/0x4ac
[ 11.747251] [<80708d74>] serial8250_probe+0x148/0x1c0
[ 11.789301] [<80728450>] platform_drv_probe+0x40/0x94
[ 11.830515] [<807264f8>] really_probe+0xf8/0x318
[ 11.870876] [<80726b7c>] __driver_attach+0x110/0x12c
[ 11.910960] [<80724374>] bus_for_each_dev+0x78/0xcc
[ 11.951134] [<80725958>] bus_add_driver+0x200/0x234
[ 11.989756] [<807273d8>] driver_register+0x84/0x148
[ 12.029832] [<80d72f84>] serial8250_init+0x138/0x198
[ 12.070447] [<80100e6c>] do_one_initcall+0x5c/0x2a0
[ 12.110104] [<80d3a208>] kernel_init_freeable+0x370/0x484
[ 12.150722] [<80a49420>] kernel_init+0x10/0xf8
[ 12.191517] [<8010756c>] ret_from_kernel_thread+0x14/0x1c
This patch makes sure the initialization code can be reached only if a port
is found.
Fixes: 6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during input overruns")
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When probing the HSUART, it is put in loopback mode in order to prevent a
potential issue that may happen on RX (Errata HSUART.1).
serial_lpc32xx_startup() moves it out of loopback mode but this is too late
to get the kernel boot messages before userspace opens the device.
Also get out of loopback mode in lpc32xx_hsuart_console_setup().
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap driver uses clock-frequency DT property to obtain functional
clk frequency. This is not ideal as users need to calculate functional
clk frequency offline and populate it in DT.
Therefore add support to obtain functional clock frequency using clk
APIs when clock-frequency DT property is not defined.
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap is DT only driver so dev->of_node always exists. Drop check
for existence of valid dev->of_node to simplify omap8250_probe().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At probe, the uart driver tries to get an id from a device tree alias.
When no alias was specified, the driver would return an error and probing
would fail.
Providing an alias for registering a serial device should not be mandatory.
If the device tree does not specify an alias, provide an id from a reserved
range so that the probing can continue.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed up
in 5.0-rc1. The second one resolves a number of reported issues with
the recent tty locking fixes that went into 5.0-rc1. Lots of people
have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXDsOzA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl8OACgg3KREaqF3vizmxVr3xzKk2xG7x0An28XJcYA
z95ZRO/BuSATH1kTM36D
=p+SA
-----END PGP SIGNATURE-----
Merge tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed
up in 5.0-rc1. The second one resolves a number of reported issues
with the recent tty locking fixes that went into 5.0-rc1. Lots of
people have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues"
* tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Don't hold ldisc lock in tty_reopen() if ldisc present
serial: lantiq: Do not swap register read/writes
In RISC-V, the M-mode runtime firmware provide SBI calls for
debug prints. This patch adds earlycon support using RISC-V
SBI console calls. To enable it, just pass "earlycon=sbi" in
kernel parameters.
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use u32 rather than unsigned long for register variables for clarity and
consistency.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver only supports FIFO mode so setting and checking this variable
is unnecessary. If DMA support is ever added then such checks can be
introduced.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variables of tx_wm and rx_wm were set to the same define value in
all cases, never updated, and the define was sometimes used
interchangably. Remove the variables/function and use the fixed value.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A frequent side comment has been to remove the use of writel_relaxed,
readl_relaxed, and mb. This reduces driver complexity and the _relaxed
variants were not known to provide any noticeable performance benefit.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most RX/TX-specific DMA functions are prefixed with "sci_dma_[rt]x_".
Rename the exceptions to increase consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting a DMA request fails in sci_dma_rx_complete(), the driver
tries to fall back to PIO, but that does not work: no more data will be
received, or the kernel will even crash.
Fix this similar as in (but not identical to) sci_submit_rx():
- On SCIF, PIO cannot take over if any DMA transactions are pending,
hence they must be terminated first.
- All active cookies must be invalidated, else rx_timer_fn() may
trigger a NULL pointer dereference.
- Restarting the port is not needed, as it is already running, but
serial port interrupts must be directed back from the DMA engine to
the CPU.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the functionality to direct new serial port interrupts back to
the CPU into its own helper, to prepare for using it from a second
callsite.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cookies and channel pointer for the DMA receive channel are
invalidated in two places, and one more is planned.
Extract this functionality in a common helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi_register_driver() may fail, so let's pass its return value upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since board support for the CLPS711X platform was removed
(commit 4a56f46a7d ("ARM: clps711x: Remove boards support")),
remove the board support from the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ltq_r32() and ltq_w32() macros use the __raw_readl() and
__raw_writel() functions which do not swap the value to little endian.
On the big endian vrx200 SoC the UART is operated in big endian IO mode,
the readl() and write() functions convert the value to little endian
first and then the driver does not work any more on this SoC.
Currently the vrx200 SoC selects the CONFIG_SWAP_IO_SPACE option,
without this option the serial driver would work, but PCI devices do not
work any more.
This patch makes the driver use the __raw_readl() and __raw_writel()
functions which do not swap the endianness. On big endian system it is
assumed that the device should be access in big endian IO mode and on a
little endian system it would be access in little endian mode.
Fixes: 89b8bd2082 ("serial: lantiq: Use readl/writel instead of ltq_r32/ltq_w32")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a9ddb575d6
("dmaengine: dw_dmac: Enhance device tree support")
introduces is_private property in uncertain understanding what does it mean.
First of all, documentation defines DMA_PRIVATE capability as
Documentation/crypto/async-tx-api.txt:
The DMA_PRIVATE capability flag is used to tag dma devices that should not be
used by the general-purpose allocator. It can be set at initialization time
if it is known that a channel will always be private. Alternatively,
it is set when dma_request_channel() finds an unused "public" channel.
A couple caveats to note when implementing a driver and consumer:
1/ Once a channel has been privately allocated it will no longer be
considered by the general-purpose allocator even after a call to
dma_release_channel().
2/ Since capabilities are specified at the device level a dma_device with
multiple channels will either have all channels public, or all channels
private.
Documentation/driver-api/dmaengine/provider.rst:
- DMA_PRIVATE
The devices only supports slave transfers, and as such isn't available
for async transfers.
The capability had been introduced by the commit 59b5ec2144
("dmaengine: introduce dma_request_channel and private channels")
and some code didn't changed from that times ever.
Taking into consideration above and the fact that on all known platforms
Synopsys DesignWare DMA engine is attached to serve slave transfers,
the DMA_PRIVATE capability must be enabled for this device unconditionally.
Otherwise, as rightfully noticed in drivers/dma/at_xdmac.c:
/*
* Without DMA_PRIVATE the driver is not able to allocate more than
* one channel, second allocation fails in private_candidate.
*/
because of of a caveats mentioned in above documentation excerpts.
So, remove conditional around DMA_PRIVATE followed by removal leftovers.
If someone wonders, DMA_PRIVATE can be not used if and only if the all channels
of the DMA controller are supposed to serve memory-to-memory like operations.
For example, EP93xx has two controllers, one of which can only perform
memory-to-memory transfers
Note, this change doesn't affect dmatest to be able to test such controllers.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (maintainer:SERIAL DRIVERS)
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should be
helpful for many.
The last patch in the series is a revert of an older one in the tree, it
came late but it resolves a reported issue that linux-next was having
for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY+1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl9PgCXckFuSe66uNMzdq2jsVgLKtMR+ACbBzrLQeMZ
LU8UpaVqDJrrPxVURGY=
=a/Xk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the large TTY/Serial driver set of patches for 4.21-rc1.
A number of small serial driver changes along with some good tty core
fixes for long-reported issues with locking. There is also a new
console font added to the tree, for high-res screens, so that should
be helpful for many.
The last patch in the series is a revert of an older one in the tree,
it came late but it resolves a reported issue that linux-next was
having for some people.
Full details are in the shortlog, and all of these, with the exception
of the revert, have been in linux-next for a while with no reported
issues"
* tag 'tty-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (85 commits)
Revert "serial: 8250: Default SERIAL_OF_PLATFORM to SERIAL_8250"
serial: sccnxp: Allow to use non-standard baud rates
serial: sccnxp: Adds a delay between sequential read/write cycles
tty: serial: qcom_geni_serial: Fix UART hang
tty: serial: qcom_geni_serial: Fix wrap around of TX buffer
serial: max310x: Fix tx_empty() callback
dt-bindings: serial: sh-sci: Document r8a774c0 bindings
dt-bindings: serial: sh-sci: Document r8a774a1 bindings
Fonts: New Terminus large console font
dt-bindings: serial: lpuart: add imx8qxp compatible string
serial: uartps: Fix interrupt mask issue to handle the RX interrupts properly
serial: uartps: Fix error path when alloc failed
serial: uartps: Check if the device is a console
serial: uartps: Add the device_init_wakeup
tty: serial: samsung: Increase maximum baudrate
tty: serial: samsung: Properly set flags in autoCTS mode
tty: Use of_node_name_{eq,prefix} for node name comparisons
tty/serial: do not free trasnmit buffer page under port lock
serial: 8250: Rate limit serial port rx interrupts during input overruns
dt-bindings: serial: 8250: Add rate limit for serial port input overruns
...
This reverts commit 6d11023c34.
It causes issues with Guenter's test systems and since there seems to
not be any agreement about _why_ this is a problem, but reverting it
fixes things, let's revert until the root cause is found.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc fixes from David Miller:
"Just some small fixes here and there, and a refcount leak in a serial
driver, nothing serious"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunsu: fix refcount leak
sparc: Set "ARCH: sunxx" information on the same line
sparc: vdso: Drop implicit common-page-size linker flag
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
su_get_type() doesn't do that. The match node are used as an identifier
to compare against the current node, so we can directly drop the refcount
after getting the node from the path as it is not used as pointer.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the use of non-standard baud rates.
For these purposes, we use the built-in timer/counter.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a delay between sequential read/write cycles,
to ensure the required minimum inactive time (tRWD). A time value
from the datasheet has been added for each type of supported chips.
The “inline” compiler attribute has been removed from the
read/write functions, simply allow the compiler to control this.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a serial console write occured while a UART transmit command was
waiting for a done signal then no further data would be sent until
something new kicked the system into gear. If there is already data
waiting in the circular buffer we must re-enable the tx watermark so we
receive the expected interrupts.
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit a1fee899e5 ("tty: serial: qcom_geni_serial: Fix
softlock") the size of TX transfers was limited to the TX FIFO size,
and wrap arounds of the UART circular buffer were split into two
transfers. With the commit wrap around are allowed within a transfer.
The TX FIFO of the geni serial port uses a word size of 4 bytes. In
case of a circular buffer wrap within a transfer the driver currently
may write an incomplete word to the FIFO, with some bytes containing
data from the circular buffer and others being zero. Since the
transfer isn't completed yet the zero bytes are sent as if they were
actual data.
Handle wrap arounds of the TX buffer properly and ensure that words
written to the TX FIFO always contain valid data (unless the transfer
is completed).
Fixes: a1fee899e5 ("tty: serial: qcom_geni_serial: Fix softlock")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Tested-by: Ryan Case <ryandcase@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Correct the RX interrupt mask value to handle the
RX interrupts properly.
Fixes: c8dbdc842d ("serial: xuartps: Rewrite the interrupt handling logic")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cdns_uart_console allocation failed there is a need to also clear
ID from ID list.
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking for console_suspend_enabled also check if the
device is a console.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialise the device wakeup.
The device_init_wakeup is needed for the wakeup to work by default.
Uart can be configured as the primary wakeup source so it is good to
enable wakeup by default.
The same functionality is enabled also by 8250_omap, atmel_serial,
omap-serial and stm32-usart.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode
again") makes a change to FIFO clearing code which its commit message
suggests was intended to be specific to use with RS485 mode, however:
1) The change made does not just affect __do_stop_tx_rs485(), it also
affects other uses of serial8250_clear_fifos() including paths for
starting up, shutting down or auto-configuring a port regardless of
whether it's an RS485 port or not.
2) It makes the assumption that resetting the FIFOs is a no-op when
FIFOs are disabled, and as such it checks for this case & explicitly
avoids setting the FIFO reset bits when the FIFO enable bit is
clear. A reading of the PC16550D manual would suggest that this is
OK since the FIFO should automatically be reset if it is later
enabled, but we support many 16550-compatible devices and have never
required this auto-reset behaviour for at least the whole git era.
Starting to rely on it now seems risky, offers no benefit, and
indeed breaks at least the Ingenic JZ4780's UARTs which reads
garbage when the RX FIFO is enabled if we don't explicitly reset it.
3) By only resetting the FIFOs if they're enabled, the behaviour of
serial8250_do_startup() during boot now depends on what the value of
FCR is before the 8250 driver is probed. This in itself seems
questionable and leaves us with FCR=0 & no FIFO reset if the UART
was used by 8250_early, otherwise it depends upon what the
bootloader left behind.
4) Although the naming of serial8250_clear_fifos() may be unclear, it
is clear that callers of it expect that it will disable FIFOs. Both
serial8250_do_startup() & serial8250_do_shutdown() contain comments
to that effect, and other callers explicitly re-enable the FIFOs
after calling serial8250_clear_fifos(). The premise of that patch
that disabling the FIFOs is incorrect therefore seems wrong.
For these reasons, this reverts commit f6aa5beb45 ("serial: 8250: Fix
clearing FIFOs in RS485 mode again").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f6aa5beb45 ("serial: 8250: Fix clearing FIFOs in RS485 mode again").
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
