Information needed to debug driver problems and firmware faults is stored
in the IOC’s MPT3SAS_ADAPTER data structure. Parameters such as IOCFacts,
IOC flags (related to sge, MSI-X, error recovery etc.), performance mode
type, TMs, internal commands reply status, etc. are present.
For debugging purposes, it is therefore helpful to be able to capture this
information so that the fault can be analyzed. Export the MPT3SAS_ADAPTER
data structure in debugfs. The data is available in:
/sys/kernel/debug/mpt3sas/scsi_hostX/ioc_dump
Link: https://lore.kernel.org/r/1588056322-29227-1-git-send-email-suganath-prabu.subramani@broadcom.com
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Generic protection fault type kernel panic is observed when user performs
soft (ordered) HBA unplug operation while IOs are running on drives
connected to HBA.
When user performs ordered HBA removal operation, the kernel calls PCI
device's .remove() call back function where driver is flushing out all the
outstanding SCSI IO commands with DID_NO_CONNECT host byte and also unmaps
sg buffers allocated for these IO commands.
However, in the ordered HBA removal case (unlike of real HBA hot removal),
HBA device is still alive and hence HBA hardware is performing the DMA
operations to those buffers on the system memory which are already unmapped
while flushing out the outstanding SCSI IO commands and this leads to
kernel panic.
Don't flush out the outstanding IOs from .remove() path in case of ordered
removal since HBA will be still alive in this case and it can complete the
outstanding IOs. Flush out the outstanding IOs only in case of 'physical
HBA hot unplug' where there won't be any communication with the HBA.
During shutdown also it is possible that HBA hardware can perform DMA
operations on those outstanding IO buffers which are completed with
DID_NO_CONNECT by the driver from .shutdown(). So same above fix is applied
in shutdown path as well.
It is safe to drop the outstanding commands when HBA is inaccessible such
as when permanent PCI failure happens, when HBA is in non-operational
state, or when someone does a real HBA hot unplug operation. Since driver
knows that HBA is inaccessible during these cases, it is safe to drop the
outstanding commands instead of waiting for SCSI error recovery to kick in
and clear these outstanding commands.
Link: https://lore.kernel.org/r/1585302763-23007-1-git-send-email-sreekanth.reddy@broadcom.com
Fixes: c666d3be99 ("scsi: mpt3sas: wait for and flush running commands on shutdown/unload")
Cc: stable@vger.kernel.org #v4.14.174+
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200224161406.GA21454@embeddedor
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print the function name in which MPT command got timed out. This will
facilitate debugging in which path corresponding MPT command got timeout in
first failure instance of log itself.
Link: https://lore.kernel.org/r/20191226111333.26131-9-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This improves mpt3sas driver default debug information collection and
allows for a higher percentage of issues being able to be resolved with a
first-time data capture. However, this improvement to balance the amount
of debug data captured with the performance of driver.
Enabled below print messages with out affecting the IO performance,
1. When task abort TM is received then print IO commands's timeout value
and how much time this command has been outstanding.
2. Whenever hard reset occurs then print from where this hard reset has
been issued.
3. Failure message should be displayed for failure scenarios without any
logging level.
4. Added a print after driver successfully register or unregistered a
target drive with the SML. This print will be useful for debugging the
issue where the drive addition or deletion is hanging at SML.
5. During driver load time print request, reply, sense and config page
pool's information such as its address, length and size. Also printed
sg_tablesize information.
Link: https://lore.kernel.org/r/20191226111333.26131-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When Firmware fault occurs then print in which path firmware fault has
occurred. This will be useful while debugging the firmware fault issues.
Link: https://lore.kernel.org/r/20191226111333.26131-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Watchdog thread polls for IOC state every 1 second. If it detects that IOC
state is in CoreDump state then it immediately stops the IOs and also
clears the outstanding commands issued to the HBA firmware and then it will
poll for IOC state to be out of CoreDump state and once it detects that IOC
state is changed from CoreDump state to Fault state (or) CoreDumpTOSec
number of seconds are elapsed then it will issue host reset operation and
moves the IOC state to Operational state and resumes the IOs.
Whenever any TM is received from SML then if driver detects the IOC state
is in CoreDump state then it will wait for CoreDump state to be cleared and
will host reset operation.
Link: https://lore.kernel.org/r/20191226111333.26131-6-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Renamed _base_after_reset_handler function to
_base_clear_outstanding_commands so that it can be used in multiple
scenarios with suitable name which matches with the operation it does.
Also renamed its child functions. No functional changes.
Link: https://lore.kernel.org/r/20191226111333.26131-4-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function _scsih_nvme_shutdown() to issue IO Unit Control message
to IOC firmware with operation code 'shutdown'. This causes IOC firmware to
issue NVMe shutdown commands to all NVMe drives attached to it.
NVMe Shutdown:
NVMe devices need to have a specific shutdown sequence performed before
power is removed. For this, the IOC firmware needs to be notified when the
system is being shutdown. So during the system shutdown time, driver issues
an IO Unit Control request with operation code MPI26_CTRL_OP_SHUTDOWN to
inform firmware that a shutdown is initiated.
This shutdown command is issued only if NVMe devices are attached to the
controller.
During each NVMe device addition, driver reads pcie device page2 to get
shutdown latency (e.g. drive's RTD3 Entry Latency) and updates the max
latency value among the added NVMe drives in ioc->max_shutdown_latency.
This is used as the timeout value for IO Unit Control command at the time
of shutdown.
When a NVMe drive is removed and its shutdown latency matches which
ioc->max_shutdown_latency then ioc->max_shutdown_latency is updated to next
max value (by iterating over the list of available devices). If the
shutdown latency is 0, then default timeout is set to six seconds.
Link: https://lore.kernel.org/r/20191226111333.26131-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From an interrupt handler path memory may be allocated using
GFP_KERNEL, replace it with GFP_ATOMIC.
_base_interrupt->_scsih_io_done->_scsih_smart_predicted_fault
Link: https://lore.kernel.org/r/20191024152835.6177-1-thenzl@redhat.com
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if user wishes to enable the host trace buffer during driver load
time, then user has to load the driver with module parameter
'diag_buffer_enable' set to one.
Alternatively now the user can enable host trace buffer by enabling the
following fields in manufacturing page11 in NVDATA (nvdata xml is used
while building HBA firmware image):
* HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can
allocate,
* HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host
should allocate,
* HostTraceBufferDecrementSizeKB - size by which host can reduce from
buffer size and retry the buffer allocation
when buffer allocation failed with previous
calculated buffer size.
The driver will register the trace buffer automatically without any module
parameter during boot time when above fields are enabled in manufacturing
page11 in HBA firmware.
Driver follows the following algorithm for enabling the host trace buffer
during driver load time:
* If user has loaded the driver with module parameter 'diag_buffer_enable'
set to one, then driver allocates 2MB buffer and registers this buffer
with HBA firmware for capturing the firmware trace logs.
* Else driver reads manufacture page11 data and checks whether
HostTraceBufferMaxSizeKB filed is zero or not?
- If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate
HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is
successful, then it will register this buffer with HBA firmware, else
in a loop the driver will try again by reducing the current buffer size
with HostTraceBufferDecrementSizeKB size until memory allocation is
successful or buffer size falls below HostTraceBufferMinSizeKB. If the
memory allocation is successful, then the buffer will be registered
with the firmware. Else, if the buffer size falls below the
HostTraceBufferMinSizeKB, then driver won't register trace buffer with
HBA firmware.
- If HostTraceBufferMaxSizeKB is zero, then driver won't register trace
buffer with HBA firmware.
Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the
protocol-specific value set by the driver (the default) or the maximum
supported by the controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth
of individual scsi devices, this implementation provides a single
sysfs entry per shost to switch between the controller max and the
driver default.
[mkp: tweaked commit desc]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In some cases, like while performing extensive expander reset or phy reset,
user may observe that drives are not visible in OS. Driver's
firmware-worker thread is blocked for more than 120 seconds resulting in a
call trace.
1. Received target add event for Device A and hence driver has registered
this device to SML by calling sas_rphy_add(). SML has half added this
device and returned the control to the driver by quitting from
sas_rphy_add() API, and started some background scanning on this device A.
2. While background scanning is going on device A, driver has received SAS
DEVICE STATUS CHANGE EVENT with RC code "Internal device reset" event and
hence driver has set tm_busy flag for this Device A from FW worker thread
context. When tm_busy flag is set then driver return scsi commands with
device busy status asking the kernel to retry the command after some time.
So background scanning for device A will be waiting for this tm_busy to be
cleared.
3. Meanwhile driver has received a target add event for Device B and hence
driver called sas_rphy_add() API to register this device with SML. But
since background scanning for Device A is still pending and SML is not
quitting from sas_rphy_add(), the driver’s firmware worker thread got
blocked.
4. Now driver has received SAS DEVICE STATUS CHANGE EVENT with RC code
"Internal device reset complete" event. But as driver’s firmware worker
thread got blocked in Step3, it can’t process this event and it was not
clearing the tm_busy flag and deadlock occurred (where SML was waiting for
tm_busy flag to be cleared and our FW worker thread is waiting for SML to
quit from sas_device_rphy_add() API).
Same deadlock will be observed even if device B is getting removed in
step3. So to limit these types of deadlocks driver will process the SAS
DEVICE STATUS CHANGE EVENT events from ISR context instead of processing
this event from worker thread context. This improvement avoids above
deadlock.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to reduce the performance drop depth observed on SATA HDD
when ATA PT command is outstanding.
Driver returns IO commands with status "SAM_STAT_BUSY" whenever ATA PT
command is outstanding. With this, IO commands will be retried until this
outstanding ATA PT to complete and hence we will observe drop in
performance.
As the driver is completing the subsequent IOs commands with SAM_STAT_BUSY
status, these IOs has to go though the block layer. Hence it adds latency
to the IOs and large performance drop is observed.
So to reduce this performance dropp, added improvement in driver to return
the subsequent IOs with SCSI_MLQUEUE_DEVICE_BUSY status instead of
completing the IOs with SAM_STAT_BUSY status when ATA PT command is
outstanding. Sending command back with SCSI_MLQUEUE_DEVICE_BUSY does not go
through complete block layer stack (as scsi_done won't be called) SML will
immediately retry the command and this method will avoid latency of block
layer stack and the performance impact will be reduced.
On Local setup, ran 512k sequential read IO operation on HGST SATA drive
with existing driver & with this improvement drivers and here is the
result,
1. With existing driver: IOs are running at bandwidth of ~230 rMB/s and
whenever any ATA PT command is outstanding (e.g issued from systemd-udevd
daemon) then this bandwidth drops to ~150 rMB/s.
2. With this improvement driver: IOs are running at bandwidth of ~230 rMB/s
and whenever any ATA PT command is outstanding then this bandwidth drops to
just ~190 rMB/s.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently with sysfs parameter "drv_support_bitmap" driver exposes whether
driver supports toolbox memory move command or not.
And application should issue the toolbox memory move command only if driver
tell that memory move tool box command is supported through this sysfs
parameter.
In future we can utilize this sysfs parameter if any new feature is added
and need to notify the same to applications.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If driver sees the NVMe drive with "DEVICE_BLOCKED" AccessStatus in its
PCIe Device Page0, then driver removes the drive from its internal list and
does not allow any IOCTL commands to be sent to the drive and will return
the IOCTLs with "-ENODEV" status.
The driver will now allow NVMe Encapsulated IOCTL issued to the NVMe device
with an access status of DEVICE_BLOCKED. This change allows the user to
flash new drive firmware online and revive the drive.
Add NVMe device only the driver's internal list even though the device is
in the blocked state so that the device will be visible to Apps. This way
Apps can send NVMe Encapsulated IOCTLs to this drive and bring the drive
online. This NVMe drive with DEVICE_BLOCKED access status won't added to
the SML, it will be added only in the driver's internal list.
[mkp: clarified desc]
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SES device of managed PCIe switch will be enumerated same as NVMe drives.
The device info type for this SES device is
MPI26_PCIE_DEVINFO_SCSI (0x4),
whereas the device info type for NVMe drives is
MPI26_PCIE_DEVINFO_NVME (0x3).
Based on this device info type driver determines whether the device is NVMe
drive or a SES device of a managed PCIe switch.
This SES device doesn't have the PCIe device page 2 information like NVMe
drives, so driver won't read PCIe device page 2 information for SES device.
This SES device uses only IEEE SGL's, So driver build's IEEE SGL's whenever
it receives any SCSI commands for this SES device.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using a virt_boundary_mask, as done for NVMe devices attached to
mpt3sas controllers, we require an unlimited max_segment_size as the virt
boundary merging code assumes that. But we also need to propagate that to
the DMA mapping layer to make dma-debug happy. The SCSI layer takes care
of that when using the per-host virt_boundary setting, but given that
mpt3sas only wants to set the virt_boundary for actual NVMe devices, we
can't rely on that. The DMA layer maximum segment is global to the HBA
however, so we have to set it explicitly. This patch assumes that mpt3sas
does not have a segment size limitation, which seems true based on the SGL
format, but will need to be verified.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support is easier with all driver parameters visible in sysfs. Also I've
replaced a constant with an octal permission.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable interrupt coalescing only on high iops queues.
In ioc config page 1, offset 0x14 (ProductSpecific field) is used to
determine interrupt coalescing enabled/disabled on per reply descriptor
post queue group(8) basis. If 31st bit is zero, then interrupt coalescing
is enabled for all reply descriptor post queues. If 31st bit is set to one,
then user can enable/disable interrupt coalescing on per reply descriptor
post queue group(8) basis. So to enable interrupt coalescing only on first
reply descriptor post queue group (i.e. on high iops queues), set bit 0 and
31.
This configuration should reset during driver unload or shutdown to the
default settings. For this, the driver takes copy of default ioc page 1 and
copies back the default or unmodified ioc page1 during unload and
shutdown. This means that on next driver load (e.g. if older version driver
is loaded by user), current modified changes on ioc page1 won't take
effect.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the IO submission path _base_get_msix_index is called twice. Initially
while getting the smid and subsequently while posting the request
descriptor (RD).
Refactor code to query msix index only while posting the request
descriptor. Save determined msix index in msix_io field.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code refactoring introduces function pointers.
Host uses Request Descriptors of different types for posting an entry onto
a request queue. Based on controller type and capabilities, host can also
use atomic descriptors other than normal descriptors. Using function
pointer will avoid if-else statements
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During expander reset handling, the driver invokes kernel function
scsi_host_find_tag() to obtain outstanding requests associated with the
scsi host managed by the driver. Driver loops from tag value zero to hba
queue depth to obtain the outstanding scmds. But when blk-mq is enabled,
the block layer may return stale entry for one or more requests. This may
lead to kernel panic if the returned value is inaccessible or the memory
pointed by the returned value is reused.
Reference of upstream discussion:
https://patchwork.kernel.org/patch/10734933/
Instead of calling scsi_host_find_tag() API for each and every smid (smid
is tag +1) from one to shost->can_queue, now driver will call this API (to
obtain the outstanding scmd) only for those smid's which are outstanding at
the driver level.
Driver will determine whether this smid is outstanding at driver level by
looking into it's corresponding MPI request frame, if its MPI request frame
is empty, then it means that this smid is free and does not need to call
scsi_host_find_tag() for it. By doing this, driver will invoke
scsi_host_find_tag() for only those tags which are outstanding at the
driver level.
Driver will check whether particular MPI request frame is empty or not by
looking into the "DevHandle" field. If this field is zero then it means
that this MPI request is empty. For active MPI request DevHandle must be
non-zero.
Also driver will memset the MPI request frame once the corresponding scmd
is processed (i.e. just before calling
scmd->done function).
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add Atlas PCIe Switch Management Port device PNPID,
Vendor Id: 0x1000
device Id: 0x00B2
This device is based on MPI 2.6 spec and it exposes one SES device to
accept management commands for the PCIe switch.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added device ID for NVMe Switch Adapter (Ambrosia).
VID: 0x1000
DID: 0x02B1
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MPI Endpoint is a PCIe switch based on MPI2.
Renaming device ID macro from MPI2_MFGPAGE_DEVID_SAS2308_MPI_EP to
MPI2_MFGPAGE_DEVID_SWITCH_MPI_EP.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 1475400 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding flag "is_aero_ioc" to differentiate aero based controllers from
other gen35 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display following warning message only upon detection of configurable
secure type controllers.
"HBA is in Configurable Secure mode"
[mkp: typos]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.
In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.
Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time). So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.
Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Aero/Sea controllers and add warning for configurable
secure type IOC.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
Convert these uses to ioc_<level> where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These have misordered uses of __func__ and ioc->name that could mismatch
MPT3SAS_FMT and "%s: ".
Convert them to ioc_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a more common logging style.
Done using the perl script below and some typing
$ git grep --name-only -w MPT3SAS_FMT -- "*.c" | \
xargs perl -i -e 'local $/; while (<>) { s/\bpr_(info|err|notice|warn)\s*\(\s*MPT3SAS_FMT\s*("[^"]+"(?:\s*\\?\s*"[^"]+"\s*){0,5}\s*),\s*ioc->name\s*/ioc_\1(ioc, \2/g; print;}'
Miscellanea for these conversions:
o Coalesce formats
o Realign arguments
o Remove unnecessary parentheses
o Use casts to u64 instead of unsigned long long where appropriate
o Convert broken pr_info uses to pr_cont
o Fix broken format string concatenation with line continuations and
excess whitespace
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
Currently this function is implemented in the scsi layer, but it's
actual place should be the block layer since T10-PI is a general
data integrity feature that is used in the nvme protocol as well.
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Avoids that warnings about the kernel headers appear when building with
W=1. Remove useless "@Returns - Nothing" clauses. Change "@Return - " into
"Return: ".
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split each of these functions in three functions - one function per reset
phase. This patch does not change any functionality but makes the code
easier to read.
Note: it is much easier to review the git diff -w output after having
applied this patch than by reviewing the patch itself.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc complains about switch/case fall-through
when building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify the indentation such that smatch no longer complains about
inconsistent indenting.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While configuring of NVMe device handling, _pcie_device structure member
was accessed after its reference count is decremented/put. Hence modified
code to access member of _pcie_device structure before its reference count
is decremented/put.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_scan_finished driver should mark port_enable_cmd.status as
'command not used', instead base_cmds.status was marked as 'command not
used'. Update code to mark port_enable_cmd.status as 'command not used'.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux driver when receives Broadcast Asynchronous Event Notification (BAEN)
from the controller firmware, checks all pending I/Os at the driver level
and issues query task, abort task TMs. This is done in the driver to handle
drives which are connected with multiple initiators and undergoing target
resets. In the BAEN handling code, the I/Os issued to NVMe drives are also
handled and query task and abort task TMs are issued, which are not
necessary as there is no multi-initiator and no BAEN concept with NVMe
drives. Hence when the driver checks for pending I/Os it skips NVMe drives
at this moment.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ioctl exit path driver refers ioc_list to free memory associated with
diag buffers and event_log pointer used to save events by driver.
If ctl_exit() func is called after unregistering driver, then ioc_list will
be empty and hence driver will not be able to free the allocated memory
which in turn causes memory leak.
So call ctl_exit() function before unregistering mpt3sas driver.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Manufacturing Page 11 contains parameters to control internal
firmware behavior. Based on AddlFlags2 field FW/Driver behaviour can
be changed, (flag tm_custom_handling is used for this)
a) For PCIe device, protocol level reset should be used if flag
tm_custom_handling is 0. Since Abort Task Set, LUN reset and Target
reset will result in a protocol level reset. Drivers should issue
only one type of this reset, if that fails then it should escalate to
a controller reset (diag reset/OCR).
b) If the driver has control over the TM reset timeout value, then
driver should use the value exposed in PCIe Device Page 2 for pcie
device (field ControllerResetTO).
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function _scsih_add_device, for each device connected to an
enclosure, driver reads the enclosure page(To get details like enclosure
handle, enclosure logical ID, enclosure level etc.)
With this patch, instead of reading enclosure page everytime, driver
maintains a list for enclosure device(During enclosure add event,
enclosure device is added to the list and removed from the list on
delete events) and uses the enclosure page from the list.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Events were not processed during driver unload, hence unloading of
driver doesn't complete when drives are disconnected while unloading of
driver. So don't block events in ISR path, i,e., remove the flag
ioc->remove_host so that events are getting processed during driver
unload. Thus allowing driver unload to complete by processing drive
removal events during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS Device Discovery Error Event is sent to the host when discovery
for a particular device is failed during discovery, even after maximum
retries by the IOC.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes sparse warnings and bugs on big endian systems.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas. In addition we have removed several really
old drivers: sym53c416, NCR53c406a, fdomain, fdomain_cs and removed
the old scsi_module.c initialization from all remaining drivers. Plus
an assortment of bug fixes, initialization errors and other minor
fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWsVSnSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbvbAP9ErpTZ
OR5iJ5HIz4W3Bd8aTfEpJrDyeYwSUC+sra5SKQD/ZWyVB3fYFSg+ZROyT26pmtmd
SdImhG7hLaHgVvF5qRQ=
=SQ/n
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The firmware event workqueue should not be marked as WQ_MEM_RECLAIM
as it's doesn't need to make forward progress under memory pressure.
In the current state it will result in a deadlock if the device had been
forcefully removed.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sending I/O through 32 bit descriptors to Ventura series of controller
results in IO timeout on certain conditions. This error only occurs on
systems with high I/O activity.
Changes in this patch will prevent driver from using 32 bit descriptor
and use 64 bit Descriptors
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This configures shost max sector to 128, single reply descriptor post
queue, sgl table size to 16 and 32 bit DMA for MPI Endpoint and it
supports 64K as max IO.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add device ID and flag for Andromeda/MPI Endpoint.
[mkp: typo]
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch finishes all outstanding SCSI IO commands (but not other commands,
e.g., task management) in the shutdown and unload paths.
It first waits for the commands to complete (this is done after setting
'ioc->remove_host = 1 ', which prevents new commands to be queued) then it
flushes commands that might still be running.
This avoids triggering error handling (e.g., abort command) for all commands
possibly completed by the adapter after interrupts disabled.
[mauricfo: introduced something in commit message.]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds checks for 'ioc->remove_host' in the SCSI error handlers, so
not to access pointers/resources potentially freed in the PCI shutdown/module
unload path. The error handlers may be invoked after shutdown/unload,
depending on other components.
This problem was observed with kexec on a system with a mpt3sas based adapter
and an infiniband adapter which takes long enough to shutdown:
The mpt3sas driver finished shutting down / disabled interrupt handling, thus
some commands have not finished and timed out.
Since the system was still running (waiting for the infiniband adapter to
shutdown), the scsi error handler for task abort of mpt3sas was invoked, and
hit an oops -- either in scsih_abort() because 'ioc->scsi_lookup' was NULL
without commit dbec4c9040 ("scsi: mpt3sas: lockless command submission"), or
later up in scsih_host_reset() (with or without that commit), because it
eventually called mpt3sas_base_get_iocstate().
After the above commit, the oops in scsih_abort() does not occur anymore
(_scsih_scsi_lookup_find_by_scmd() is no longer called), but that commit is
too big and out of the scope of linux-stable, where this patch might help, so
still go for the changes.
Also, this might help to prevent similar errors in the future, in case code
changes and possibly tries to access freed stuff.
Note the fix in scsih_host_reset() is still important anyway.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance improvement using block layer tag.
Curent driver gets scsiio tracker and free smid from link list and array
based tracking managed by driver. Accessing list in main io path is
performance pentaly because of protection using spinlock
"scsi_lookup_lock".
In this patch:
1. Driver removes all link list access from main io path and
use scmd->request->tag to get free smid.
2. Instead of holding 'struct scsiio_tracker' in its own pool
driver can embed it into the scsi command.
Driver provides cmd_size in scsi_host_template, so that struct
scsiio_tracker is preallocated by scsi mid layer for each scsi command.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the check for outstanding commands out of the function allowing us
to simplify the overall code.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Code optimization.
One can simply check 'target_busy' or 'device_busy' when figuring out if
there are outstanding commands; no need to painstakingly count them by
hand.
[mkp: tweaked patch description]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When attempting a command abort we should check the command status prior
to sending the abort; the command might've been completed already.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abstract accesses to the scsi_lookup array by introducing
mpt3sas_get_st_from_smid().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Just a wrapper around the scsi lookup array and only used in one place,
so open-code it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. In IO path, setting of "ATA command pending" flag early before device
removal, invalid device handle etc., checks causes any new commands
to be always returned with SAM_STAT_BUSY and when the driver removes
the drive the SML issues SYNC Cache command and that command is
always returned with SAM_STAT_BUSY and thus making SYNC Cache command
to requeued.
2. If the driver gets an ATA PT command for a SATA drive then the driver
set "ATA command pending" flag in device specific data structure not
to allow any further commands until the ATA PT command is completed.
However, after setting the flag if the driver decides to return the
command back to upper layers without actually issuing to the firmware
(i.e., returns from qcmd failure return paths) then the corresponding
flag is not cleared and this prevents the driver from sending any new
commands to the drive.
This patch fixes above two issues by setting of "ATA command pending"
flag after checking for whether device deleted, invalid device handle,
device busy with task management. And by setting "ATA command pending"
flag to false in all of the qcmd failure return paths after setting the
flag.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No Functional change just cleanup. Removed variable requeue_event and
made function as void.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
pr_info() has a KERN_INFO already so the second KERN_INFO isn't needed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The indenting wasn't right, because the last two prints weren't indented
far enough. Also it used pr_info() where it was supposed to use
pr_cont(). I reversed the if statement and pulled the code in one tab
and did a couple other minor cleanups.
Fixes: 4318c73478 ("scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Used variable __le64/__le32 whichever required in building NVME
PRP, and passed to LE Controller.
2) Remove unused functions, And Declared functions as static which are
used only in mpt3sas_scsih.c.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check for NVMe drives before enabling or checking tlr.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added debug information for NVMe/PCIe drives in target rest path
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After Controller reset, Scan and add nvme device back to the topology.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sets nvme device queue depth, name and displays device capabilities
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* The controller firmware sends separate events for NVMe devices and
PCIe switches similar to existing SAS events.
* NVMe device detection, addition and removal are reported by the
firmware through PCIe Topology Change list events.
* The PCIe device state change events are sent when the firmware
detects any abnormal conditions with a NVMe device or switch.
* The enumeration event are sent when the firmware starts PCIe device
enumeration and stops.
* This patch has the code change to handle the events and add/remove
NVMe devices in driver's inventory.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following functions are called in nvme drive remove path:
_scsih_pcie_device_remove_by_handle
_scsih_pcie_device_remove_from_sml
[mkp: clarify commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Below Functions are added in various paths to support NVMe drive
addition.
_scsih_pcie_add_device
_scsih_pcie_device_add
_scsih_pcie_device_init_add
_scsih_check_pcie_access_status
_scsih_pcie_check_device
mpt3sas_get_pdev_by_handle
mpt3sas_config_get_pcie_device_pg0
mpt3sas_config_get_pcie_device_pg2
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Added support for translating the SGLs associated with incoming
commands either to IEE SGL or NVMe PRPs for NVMe devices.
* The hardware translation of IEEE SGL to NVMe PRPs has limitations
and if a command cannot be translated by hardware then it will go to
firmware and the firmware needs to translate it. This will have a
performance impact. To avoid that, the driver proactively checks
whether the translation will be done in hardware or not. If not, then
driver translates.
[mkp: clarified commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Added support for probing pcie device and adding NVMe drives to SML
and driver's internal list pcie_device_list.
2) Added support for determing NVMe as boot device.
3) Added nvme device support for call back functions scan_finished
target_alloc,slave_alloc,target destroy and slave destroy.
a) During scan, pcie devices are probed and added to SML to drivers
internal list.
b) target_alloc & slave alloc API's allocates resources for
(MPT3SAS_TARGET & MPT3SAS_DEVICE) private datas and holds information
like handle, target_id etc.
c) slave_destroy & target_destroy are called when driver unregisters
or removes device. Also frees allocated resources and info.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Adding PNP ID of Mercator i.e. SAS3616 HBA device. Its device ID is
0xD1 and vendor ID is 0x1000.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enclosure handles are not updated after host reset. As a result, driver
device structure is holding previously assigned enclosure handle which
is different from the enclosure handle populated in the corresponding
device page.
Modified the driver to update devices enclosure handles after host reset
to current value by referring the enclosure handles from corresponding
device pages
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display chassis slot information along with other drive location
parameters such as slot number and connector name in the logs if
chassis slot validity bit is set in 'SAS Enclosure Page 0'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Dev Handles whose value is less than HBA's phys count number, driver
would return HBA's SAS address value. As a result, for a Virtual SES
device the driver was returning the HBA's SAS address. Updated the
driver to return Virtual SES' SAS address.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While removing Expander devices, we are removing expander device entry
from the list before freeing its child devices. While freeing child
device we are finding its parent device node as NULL and therefore we
are not freeing the child device's allocated data structures. Updated
the driver to remove the expander device from the list only after
freeing all its child devices.
[mkp: clarified commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.
Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.
[mkp: typos]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This will make it easier to serialize SCSI device state changes through
a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of passing a "wait" argument to scsi_internal_device_block(),
split this function into a function that waits and a function that
doesn't wait. This will make it easier to serialize SCSI device state
changes through a mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
