T10 PI support on SLI-4-based FCoE adapters is not supported. A prior
commit in the 12.4.0.0 stream added device recognition that would prevent
T10 PI enablement. However, it didn't contain a complete device list. Thus
some SLI-4 FCoE adapters still had T10 PI enabled.
Fix by expanding the device list that identifies FCoE devices.
Link: https://lore.kernel.org/r/20190922035906.10977-19-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged missing status check on register read that flags a
poisoned data return value.
Add checking of register read status.
Link: https://lore.kernel.org/r/20190922035906.10977-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added code to support driver loopback with MDS Diagnostics. This style of
diagnostics passes frames from the fabric to the driver who then echo them
back out the link. SEND_FRAME WQEs are used to transmit the frames. Added
the SOF and EOF field location definitions for use by SEND_FRAME.
Also ensure that enable_mds_diags is a RW parameter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To aid better hardware detection when there are issues, report the first
and second level hardware revisions from the READ_REV command. Add the
elements to the existing hardware id string.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
modinfo for lpfc_nvme_enable_fb is incorrect. FirstBurst on lpfc target is
not fully supported.
Update the attribute description
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is allowing the user to change lpfc_enable_bg while loading the
driver against a FCoE adapter. This is not supported.
No check is made for the adapter type when applying the blockguard
enablement value.
Fix by verifying the adapter type before setting the enablement flag.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When SCSI-MQ is enabled, the SCSI-MQ layers will do pre-allocation of MQ
resources based on shost values set by the driver. In newer cases of the
driver, which attempts to set nr_hw_queues to the cpu count, the
multipliers become excessive, with a single shost having SCSI-MQ
pre-allocation reaching into the multiple GBytes range. NPIV, which
creates additional shosts, only multiply this overhead. On lower-memory
systems, this can exhaust system memory very quickly, resulting in a system
crash or failures in the driver or elsewhere due to low memory conditions.
After testing several scenarios, the situation can be mitigated by limiting
the value set in shost->nr_hw_queues to 4. Although the shost values were
changed, the driver still had per-cpu hardware queues of its own that
allowed parallelization per-cpu. Testing revealed that even with the
smallish number for nr_hw_queues for SCSI-MQ, performance levels remained
near maximum with the within-driver affiinitization.
A module parameter was created to allow the value set for the nr_hw_queues
to be tunable.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
To support scenarios which aren't bound to nvmetcli add port scenarios,
which is currently where the nvmet_fc transport invokes the discovery
event callbacks, a syfs attribute is added to lpfc which can be written
to cause an RSCN to be generated for the nport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the exit cases were not releasing the rcu read lock. Corrected the
exit paths.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There were a number of erroneous comments and incorrect older lockdep
checks that were causing a number of warnings.
Resolve the following:
- Inconsistent lock state warnings in lpfc_nvme_info_show().
- Fixed comments and code on sequences where ring lock is now held instead
of hbalock.
- Reworked calling sequences around lpfc_sli_iocbq_lookup(). Rather than
locking prior to the routine and have routine guess on what lock, take
the lock within the routine. The lockdep check becomes unnecessary.
- Fixed comments and removed erroneous hbalock checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arrays should be defined in .c files instead of in a header file. This
patch reduces the size of the lpfc kernel module.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: James Smart <james.smart@broadcom.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid test is allowing Loop to be a supported topology on G6 and G7
adapters. The chips do not support loop as their link speeds prohibit loop
per standard.
Correct the conditional so that loop is not reported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For files modified as part of 12.2.0.0 patches, update copyright to 2019
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The conversion to enable SCSI and NVME fc4 support ran into an issue with
NPIV support. With NVME, NPIV is not currently supported, but with SCSI it
was. The driver reverted to its lowest setting meaning NPIV with SCSI was
not allowed.
Convert the NPIV checks and implementation so that SCSI can continue to
allow NPIV support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that performance mods don't split resources by protocol and enable both
protocols by default, there's no reason not to enable concurrent SCSI and
NVME fc4 support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The work done to date utilized the number of present cpus when sizing
per-cpu structures. Structures should have been sized based on the max
possible cpu count.
Convert the driver over to possible cpu count for sizing allocation.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driving high iop counts, auto_imax coalescing kicks in and drives the
performance to extremely small iops levels.
There are two issues:
1) auto_imax is enabled by default. The auto algorithm, when iops gets
high, divides the iops by the hdwq count and uses that value to
calculate EQ_Delay. The EQ_Delay is set uniformly on all EQs whether
they have load or not. The EQ_delay is only manipulated every 5s (a
long time). Thus there were large 5s swings of no interrupt delay
followed by large/maximum delay, before repeating.
2) When processing a CQ, the driver got mixed up on the rate of when
to ring the doorbell to keep the chip appraised of the eqe or cqe
consumption as well as how how long to sit in the thread and
process queue entries. Currently, the driver capped its work at
64 entries (very small) and exited/rearmed the CQ. Thus, on heavy
loads, additional overheads were taken to exit and re-enter the
interrupt handler. Worse, if in the large/maximum coalescing
windows,k it could be a while before getting back to servicing.
The issues are corrected by the following:
- A change in defaults. Auto_imax is turned OFF and fcp_imax is set
to 0. Thus all interrupts are immediate.
- Cleanup of field names and their meanings. Existing names were
non-intuitive or used for duplicate things.
- Added max_proc_limit field, to control the length of time the
handlers would service completions.
- Reworked EQ handling:
Added common routine that walks eq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after eqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Moved lpfc_sli4_eq_flush(), which does similar action, to same area.
Replaced the 2 individual loops that walk an eq with a call to the
common routine.
Slightly revised lpfc_sli4_hba_handle_eqe() calling syntax.
Added per-cpu counters to detect interrupt rates and scale
interrupt coalescing values.
- Reworked CQ handling:
Added common routine that walks cq, applying notify interval and max
processing limits. Use queue_claimed to claim ownership of the queue
while processing. Always rearm the queue whenever the common routine
is called.
Rework queue element processing, namely to eliminate hba_index vs
host_index. Only one index is necessary. The queue entry can be
marked invalid and the host_index updated immediately after cqe
processing.
After rework, xx_release routines are now DB write functions. Renamed
the routines as such.
Replaced the 3 individual loops that walk a cq with a call to the
common routine.
Redefined lpfc_sli4_sp_handle_mcqe() to commong handler definition with
queue reference. Add increment for mbox completion to handler.
- Added a new module/sysfs attribute: lpfc_cq_max_proc_limit To allow
dynamic changing of the CQ max_proc_limit value being used.
Although this leaves an EQ as an immediate interrupt, that interrupt will
only occur if a CQ bound to it is in an armed state and has cqe's to
process. By staying in the cq processing routine longer, high loads will
avoid generating more interrupts as they will only rearm as the processing
thread exits. The immediately interrupt is also beneficial to idle or
lower-processing CQ's as they get serviced immediately without being
penalized by sharing an EQ with a more loaded CQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Review of the eq coalescing logic showed the code was a bit fragmented.
Sometimes it would save/set via an interrupt max value, while in others it
would do so via a usdelay. There were also two places changing eq delay,
one place that issued mailbox commands, and another that changed via
register writes if supported.
Clean this up by:
- Standardizing the operation of lpfc_modify_hba_eq_delay() routine so
that it is always told of a us delay to impose. The routine then chooses
the best way to set that - via register or via mbx.
- Rather than two value types stored in eq->q_mode (usdelay if change via
register, imax if change via mbox) - q_mode always contains usdelay.
Before any value change, old vs new value is compared and only if
different is a change done.
- Revised the dmult calculation. dmult is not set based on overall imax
divided by hardware queues - instead imax applies to a single cpu and
the value will be replicated to all cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
So far MSIX vector allocation assumed it would be 1:1 with hardware
queues. However, there are several reasons why fewer MSIX vectors may be
allocated than hardware queues such as the platform being out of vectors or
adapter limits being less than cpu count.
This patch reworks the MSIX/EQ relationships with the per-cpu hardware
queues so they can function independently. MSIX vectors will be equitably
split been cpu sockets/cores and then the per-cpu hardware queues will be
mapped to the vectors most efficient for them.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The desired affinity for the hardware queue behavior is for hdwq 0 to be
affinitized with cpu 0, hdwq 1 to cpu 1, and so on. The implementation so
far does not do this if the number of cpus is greater than the number of
hardware queues (e.g. hardware queue allocation was administratively
reduced or hardware queue resources could not scale to the cpu count).
Correct the queue affinitization logic when queue count is less than
cpu count.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior is to use the information from the upper IO stacks to
select the hardware queue to use for IO submission. Which typically has
good cpu affinity.
However, the driver, when used on some variants of the upstream kernel, has
found queuing information to be suboptimal for FCP or IO completion locked
on particular cpus.
For command submission situations, the lpfc_fcp_io_sched module parameter
can be set to specify a hardware queue selection policy that overrides the
os stack information.
For IO completion situations, rather than queing cq processing based on the
cpu servicing the interrupting event, schedule the cq processing on the cpu
associated with the hardware queue's cq.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The XRI get/put lists were partitioned per hardware queue. However, the
adapter rarely had sufficient resources to give a large number of resources
per queue. As such, it became common for a cpu to encounter a lack of XRI
resource and request the upper io stack to retry after returning a BUSY
condition. This occurred even though other cpus were idle and not using
their resources.
Create as efficient a scheme as possible to move resources to the cpus that
need them. Each cpu maintains a small private pool which it allocates from
for io. There is a watermark that the cpu attempts to keep in the private
pool. The private pool, when empty, pulls from a global pool from the
cpu. When the cpu's global pool is empty it will pull from other cpu's
global pool. As there many cpu global pools (1 per cpu or hardware queue
count) and as each cpu selects what cpu to pull from at different rates and
at different times, it creates a radomizing effect that minimizes the
number of cpu's that will contend with each other when the steal XRI's from
another cpu's global pool.
On io completion, a cpu will push the XRI back on to its private pool. A
watermark level is maintained for the private pool such that when it is
exceeded it will move XRI's to the CPU global pool so that other cpu's may
allocate them.
On NVME, as heartbeat commands are critical to get placed on the wire, a
single expedite pool is maintained. When a heartbeat is to be sent, it will
allocate an XRI from the expedite pool rather than the normal cpu
private/global pools. On any io completion, if a reduction in the expedite
pools is seen, it will be replenished before the XRI is placed on the cpu
private pool.
Statistics are added to aid understanding the XRI levels on each cpu and
their behaviors.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many io statistics were being sampled and saved using adapter-based data
structures. This was creating a lot of contention and cache thrashing in
the I/O path.
Move the statistics to the hardware queue data structures. Given the
per-queue data structures, use of atomic types is lessened.
Add new sysfs and debugfs stat routines to collate the per hardware queue
values and report at an adapter level.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once the IO buff allocations were made shared, there was a single XRI
buffer list shared by all hardware queues. A single list isn't great for
performance when shared across the per-cpu hardware queues.
Create a separate XRI IO buffer get/put list for each Hardware Queue. As
SGLs and associated IO buffers get allocated/posted to the firmware; round
robin their assignment across all available hardware Queues so that there
is an equitable assignment.
Modify SCSI and NVME IO submit code paths to use the Hardware Queue logic
for XRI allocation.
Add a debugfs interface to display hardware queue statistics
Added new empty_io_bufs counter to track if a cpu runs out of XRIs.
Replace common_ variables/names with io_ to make meanings clearer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both nvme and fcp each have their own concept of an io_channel,
which is a combination wq/cq and associated msix. Different cpus would
share an io_channel.
The driver is now moving to per-cpu wq/cq pairs and msix vectors. The
driver will still use separate wq/cq pairs per protocol on each cpu, but
the protocols will share the msix vector.
Given the elimination of the nvme and fcp io channels, the module
parameters will be removed. A new parameter, lpfc_hdw_queue is added which
allows the wq/cq pair allocation per cpu to be overridden and allocated to
lesser value. If lpfc_hdw_queue is zero, the number of pairs allocated will
be based on the number of cpus. If non-zero, the parameter specifies the
number of queues to allocate. At this time, the maximum non-zero value is
64.
To manage this new paradigm, a new hardware queue structure is created to
track queue activity and relationships.
As MSIX vector allocation must be known before setting up the
relationships, msix allocation now occurs before queue datastructures are
allocated. If the number of vectors allocated is less than the desired
hardware queues, the hardware queue counts will be reduced to the number of
vectors
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, both NVME and SCSI get their IO buffers from separate
pools. XRI's are associated 1:1 with IO buffers, so XRI's are also split
between protocols.
Eliminate the independent pools and use a single pool. Each buffer
structure now has a common section and a protocol section. Per protocol
routines for SGL initialization are removed and replaced by common
routines. Initialization of the buffers is only done on the common area.
All other fields, which are protocol specific, are initialized when the
buffer is allocated for use in the per-protocol allocation routine.
In the past, the SCSI side allocated IO buffers as part of slave_alloc
calls until the maximum XRIs for SCSI was reached. As all XRIs are now
common and may be used for either protocol, allocation for everything is
done as part of adapter initialization and the scsi side has no action in
slave alloc.
As XRI's are no longer split, the lpfc_xri_split module parameter is
removed.
Adapters based on SLI3 will continue to use the older scsi_buf_list_get/put
routines. All SLI4 adapters utilize the new IO buffer scheme
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute.
This option uses the pci_reset_bus() api to reset the PCIe link the adapter
is on, which will reset the chip/adapter. Prior to issuing this option,
all functions on the same chip must be placed in the offline state by the
admin. After the reset, all of the instances may be brought online again.
The primary purpose of this functionality is to support cases where
firmware update required a chip reset but the admin did not want to reboot
the machine in order to instantiate the firmware update.
Sanity checks take place prior to the reset to ensure the adapter is the
sole entity on the PCIe bus and that all functions are in the offline
state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.
Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.
Add the chip classifications to the topology checks in the driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.
Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code. Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.
Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.
This patch contains the following modifications:
- Added link speed settings of 128GB and 256GB.
- Added handling of trunk-related ACQEs, mainly logging and trapping
of physical link statuses.
- Added additional bsg interface to query trunk state by applications.
- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries. Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
The driver currently uses the ndlp to get the local rport which is then used
to get the nvme transport remoteport pointer. There can be cases where a stale
remoteport pointer is obtained as synchronization isn't done through the
different dereferences.
Correct by using locks to synchronize the dereferences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme is enabled, change the default for two parameters:
sg_seg_cnt - raise the per-io sg list size so that 1MB ios are
supported (based on a 4k buffer per element).
iocb_cnt - raise the number of buffers used for things like
NVME LS request/responses to allow more concurrent requests
to for larger nvme configs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver allocates a sg list per io struture based on a fixed maximum
size. When it registers with the protocol transports and indicates the max sg
list size it supports, the driver manipulates the fixed value to report a
lesser amount so that it has reserved space for sg elements that are used for
DIF.
The driver initialization path sets the cfg_sg_seg_cnt field to the
manipulated value for scsi. NVME initialization ran afterward and capped it's
maximum by the manipulated value for SCSI. This erroneously made NVME report
the SCSI-reduce-for-DIF value that reduced the max io size for nvme and wasted
sg elements.
Rework the driver so that cfg_sg_seg_cnt becomes the overall maximum size and
allow the max size to be tunable. A separate (new) scsi sg count is then
setup with the scsi-modified reduced value. NVME then initializes based off
the overall maximum.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change default behavior for fdmi registration to on.
[mkp: patch was mangled]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enablement of the PBDE optimization brought out some incompatible behaviors
under error scenarios.
Best to disable and remove the PBDE optimization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CNA ports were showing speed as "unknown" even if the link is up.
Add speed decoding for FCOE-based adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PBDE optimizations aren't supported in all firmware revs.
Make optimizations configurable in case there's a side effect on old
firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel crashes during fill_read_buffer when nvme_info sysfs file read.
With multiple NVME targets, approx 40, nvme_info may grow larger than
PAGE_SIZE bytes. snprintf(buf + len, PAGE_SIZE - len, ...) logic is flawed
as PAGE_SIZE - len can be < 0 and is accepted by snprintf. This results in
buffer overflow, and is detected with check from dev_attr_show and
fill_read_buffer.
Change to use scnprintf to a tmp array, before calling strlcat to ensure no
buffer overflow over PAGE_SIZE bytes.
Message "6314" created as a new message indicating when there is more nvme
info, but is truncated to fit within PAGE_SIZE bytes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The get_seconds() function suffers from a possible overflow in 2038 or
2106, as well as jitter due to settimeofday or leap second updates, and is
deprecated.
As we are interested in elapsed time only, using ktime_get_seconds() to
read the CLOCK_MONOTONIC timebase is ideal here. This also lets us remove
the hack that tries to deal with get_seconds() going slightly backwards,
which cannot happen with montonic timestamps.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large configurations, the driver would start to log message 6065 -
NVME out of buffers (exchanges).
The driver is using the ndlp cmd_qdepth value when determining the max
outstanding ios for an adapter. This value, by default, is set to 65536,
which exceeds the maximum exchange counts supported on an adapter. The ndlp
cmd_qdepth has no relevance and outstanding io count should be capped at
the max exchange count with IO requests beyond that level getting bounced
back with an EBUSY status so that they are retried by the block layer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix small formatting and wording nits in Broadcom copyright header
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix up log messages and add an fcp error stat counter in the IO submit
code path to make diagnosing problems easier
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After making remoteport unregister requests, the ndlp nrport pointer was
stale.
Track when waiting for waiting for unregister completion callback and
adjust nldp pointer assignment. Add a few safety checks for NULL
pointer values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under large io load, the current sizing of asynchronous buffer counts
could be exceeded, indicated by a 2885 log message:
2885 Port Status Event: port status reg 0x81800000, port smphr
reg 0xc000, error 1=0x52004a01, error 2=0x0
Enlarge the async receive queue size. Allow for a configurable number
of buffers to be posted to each RQ, using the new attribute
lpfc_nvmet_mrq_post.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When debugging various issues, per IO channel IO statistics were useful
to understand what was happening. However, many of the stats were on a
port basis rather than an io channel basis.
Move statistics to an io channel basis.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The max_scsicmpl_time parameter can be used to perform scsi cmd queue
depth mgmt based on io completion time: the queue depth is reduced to
make completion time shorter. However, as soon as an io completes and
the completion time is within limits, the code immediately bumps the
queue depth limit back up to the target queue depth. Thus the procedure
restarts, effectively limiting the usefulness of adjusting queue depth
to help completion time.
This patch makes the following changes:
- Removes the code at io completion that resets the queue depth as soon
as within limits.
- As the code removed was where the target queue depth was first
applied, change target queue depth application so that it occurs when
the parameter is changed.
- Makes target queue depth a standard parameter: both a module
parameter and a sysfs parameter.
- Optimizes the command pending count by using atomics rather than
locks.
- Updates the debugfs nodelist stats to allow better debugging of
pending command counts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4
There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment. The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.
Fix by explicitly tracking sli4 vs sli3 and BG options. The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).
A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.
For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.
Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The G7 adapter supports 64G link speeds. Add support to the driver.
In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture. Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.
This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
Default is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver ignored checks on whether the link should be kept
administratively down after a link bounce. Correct the checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the attribute writeable.
Remove the ramp up to logic as its unnecessary, simply set depth. Add
debug message if depth changed, possibly reducing limit, yet our
outstanding count has yet to catch up with it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme target deferred receive logic waits for exchange resources,
the corresponding receive buffer is not replenished with the hardware.
This can result in a lack of asynchronous receive buffer resources in
the hardware, resulting in a "2885 Port Status Event: ... error
1=0x52004a01 ..." message.
Correct by replenishing the buffer whenenver the deferred logic kicks
in. Update corresponding debug messages and statistics as well.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
localport is being dereferenced to assign lport and then immediately
afterwards localport is being sanity checked to see if it is null. Fix
this by only dereferencing localport until after it has been null
checked.
Detected by CoverityScan, CID#1463038 ("Dereference before null check")
Fixes: 3a8cefbfc5ee ("scsi: lpfc: Beef up stat counters for debug")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior patch mixed up what argument in the macro was what, so min value
was placed as the "default" argument, and the default value was placed
as the "min" argument. Thus, when the default was applied, it looked
like the default was smaller than the allowed min.
Swap argument postions to correct.
[mkp: fixed checkpatch warning]
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If log verbose in not turned on, its hard to tell when certain error
paths get hit. Add stats counters and corresponding logic to
debugfs/sysfs to aid understanding what paths were traversed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for sg_seg_cnt is a bit convoluted. This patch tries to clean
up a couple of areas, especially around the +2 and +1 logic.
This patch:
- Cleans up the lpfc_sg_seg_cnt attribute to specify a real minimum
rather than making the minimum be whatever the default is.
- Removes the hardcoding of +2 (for the number of elements we use in a
sgl for cmd iu and rsp iu) and +1 (an additional entry to compensate
for nvme's reduction of io size based on a possible partial page)
logic in sg list initialization. In the case where the +1 logic is
referenced in host and target io checks, use the values set in the
transport template as that value was properly set.
There can certainly be more done in this area and it will be addressed
in combined host/target driver effort.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current default for async hw receive queues is 1, which presents
issues under heavy load as number of queues influence the available
async receive buffer limits.
Raise the default to the either the current hw limit (16) or the number
of hw qs configured (io channel value).
Revise the attribute definition for mrq to better reflect what we do for
hw queues. E.g. 0 means default to optimal (# of cpus), non-zero
specifies a specific limit. Before this change, mrq=0 meant target mode
was disabled. As 0 now has a different meaning, rework the if tests to
use the better nvmet_support check.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
This patch calls the new nvme transport routine for dev_loss_tmo
whenever the SCSI fc transport calls the lldd to make a dynamic
change to a remote ports dev_loss_tmo.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The descriptions for lpfc_xri_split and lpfc_enable_fc4_type were
poor. Revise for better understanding:
lpfc_xri_split - Percentage of FCP XRI resources versus NVME
lpfc_enable_fc4_type - Enable FC4 Protocol support - FCP / NVME
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver crashes when attempting to use a freed ndpl pointer.
The pci_remove_one handler runs on a separate kernel thread. The order
of the removal is starting by freeing all of the ndlps and then
disabling interrupts. In between these two events the driver can still
receive an ELS and process it. When it tries to use the ndlp pointer
will be NULL
Change the order of the pci_remove_one vs disable interrupts so that
interrupts are disabled before the ndlp's are freed.
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJZscDNAAoJEAVr7HOZEZN4DWIQAK/UkkrvKpV/jLATM/yi7CoL
QidY86Hmwwl7A9HQ+2fjLfAsye0xcCzRwkucKK90IP5b4pefHhiJJfiMKAAe3TUW
xstnY5z5jaOhDG4nyJFoSm5fH5qXkMnJ8NZRK8f6Qg5yBN5dStEKqoBboNsz4KBI
md7idw0mbp5i2GXlJwSpc5eDS97GiPL6WkwgGaGKfXF1NDau0GbEdjijfz55haCD
pMhY7WJh/71RfOq/1ThXT1Z3khOlVcKXrkdO+602n7zh/klRBRtBC8m2a6xCfZPj
n7Pb/s0jhCQPd+e/Xtv7WEbY8uNOCrGoVgZ6U5EGrT5IeTfep24ackYqerjMhE63
esi4BJY8lUP9SGleLMgjYWyCHdmxBJRa7UI614DWN/H0QoGP6j/2EzGoi5Fw04vC
H8/+aqPPWZc9KUBioRYo8xWO8YgMqL2eyXY+Tc9cwxqAe2T6k/NC1zJVgDFKXfzb
QoWW4v9NNmYwf5vL/7tNgkeTMFQV66yUR7dR3SGTSk8UIrJ40ok0JyUAsDg86ZAH
BfMkWwhWQ6Byoel0Y7Ti88T49Cox/64r/I0ux06Qgg99+KpRLT7z20+GLIEHgXxg
116C39rgvYKqzc7W8RCyj8qSROuMVzg6QFbB6n+1PEsYIX2O8A2Re3jdS34q2LbX
aBDm/Lfdl4kkJrV9xY6P
=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
Add Buffer to buffer credit recovery support to the driver. This is a
negotiated feature with the peer that allows for both sides to detect
dropped RRDY's and FC Frames and recover credit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Various oops including cpu LOCKUPs were seen.
For asynchronously received ius where the driver must assign exchange
resources, the resources were on a single get (free) list and put list
(finished, waiting to be put on get list). As all cpus are sharing the
lists, an interrupt for a receive frame may have to wait for all the
other cpus to place their done work onto the put list before it can
acquire the lock to pull from the list.
Fix by breaking the resource lists into per-cpu lists or at least more
than 1 list with cpu's sharing the lists). A cpu would allocate from the
free list for its own cpu, and put its done work on the its own put list
- avoiding the contention. As cpu load may vary, when empty, a cpu may
grab from another cpu, thereby changing resource distribution. But
searching for a resource only occurs on 1 or a few cpus until a single
resource can be allocated. if the condition reoccurs, it starts looking
at a different cpu.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, calls to nvmet_fc_rcv_fcp_req() always copied the
FC-NVME cmd iu to a temporary buffer before returning, allowing
the driver to immediately repost the buffer to the hardware.
To address timing conditions on queue element structures vs async
command reception, the nvmet_fc transport occasionally may need to
hold on to the command iu buffer for a short period. In these cases,
the nvmet_fc_rcv_fcp_req() will return a special return code
(-EOVERFLOW). In these cases, the LLDD must delay until the new
defer_rcv lldd callback is called before recycling the buffer back
to the hw.
This patch adds support for the new nvmet_fc transport defer_rcv
callback and recognition of the new error code when passing commands
to the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since unsol rcv ISR and command cmpl ISR both access/lock this list,
separate get/put lists will reduce contention.
Replaced
struct list_head lpfc_nvmet_ctx_list;
with
struct list_head lpfc_nvmet_ctx_get_list;
struct list_head lpfc_nvmet_ctx_put_list;
and all correpsonding locks and counters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First line of nvme_info output is not consistent. There is an Extra
colon in the format.
First line of output will contain one of the following strings:
NVME Initiator Enabled
NVME Target Enabled
NVME Disabled
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Administrator intervention is currently required to get good numbers
when switching from running latency tests to IOPS tests.
The configured interrupt coalescing values will greatly effect the
results of these tests. Currently, the driver has a single coalescing
value set by values of the module attribute. This patch changes the
driver to support auto-configuration of the coalescing value based on
the total number of outstanding IOs and average number of CQEs processed
per interrupt for an EQ. Values are checked every 5 seconds.
The driver defaults to the automatic selection. Automatic selection can
be disabled by the new lpfc_auto_imax module_parameter.
Older hardware can only change interrupt coalescing by mailbox
command. Newer hardware supports change via a register. The patch
support both.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On hbacmd reset failure, observing wrong string "nline" in kernel log.
On failure, non negative value (1) is returned from sysfs store
routine. It is interpreted as count by kernel and store routine is
called again with the remaining characters as input.
Fix: Return negative error code (-EIO) in case of failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME FC counters don't reflect actual results
Since counters are not atomic, or protected by a lock, the values often
get screwed up.
Make them atomic, like NVMET. Fix up sysfs and debugfs display
accordingly Added Outstanding IOs to stats display
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While debugging Devloss and recovery, debugfs and sysfs were found to
not show the NVME port roles consistently.
The port role FC_PORT_ROLE_NVME_DISCOVERY was added with the devloss
bringup and the other issues were just oversight.
Add NVME Target and DISCSRVC to debugfs nodeinfo and sysfs nvme info
handlers. The full port role was added to the NVME data only not the
generic nodelist.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As the devloss API was implemented in the nvmei driver, an evaluation of
the nvme transport and the lpfc driver showed dual management of the
rports. This creates a bug possibility when the thread count and SAN
size increases.
The nvmei driver code was based on a very early transport and was not
revisited until the devloss API was introduced.
Remove the listhead in the driver's rport data structure and the
listhead in the driver's lport data structure. Remove all rport_list
traversal. Convert the driver to use the nrport (nvme rport) pointer
that is now NULL or nonNULL depending on a devloss action. Convert
debugfs and nvme_info in sysfs to use the fc_nodes list in the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add nvme initiator devloss support
The existing implementation was based on no devloss behavior in the
transport (e.g. immediate teardown) so code didn't properly handle
delayed nvme rport device unregister calls. In addition, the driver was
not correctly cycling the rport port role for each
register-unregister-reregister process.
This patch does the following:
Rework the code to properly handle rport device unregister calls and
potential re-allocation of the remoteport structure if the port comes
back in under dev_loss_tmo.
Correct code that was incorrectly cycling the rport port role for each
register-unregister-reregister process.
Prep the code to enable calling the nvme_fc transport api to dynamically
update dev_loss_tmo when the scsi sysfs interface changes it.
Memset the rpinfo structure in the registration call to enforce "accept
nvme transport defaults" in the registration call. Driver parameters do
influence the dev_loss_tmo transport setting dynamically.
Simplifies the register function: the driver was incorrectly searching
its local rport list to determine resume or new semantics, which is not
valid as the transport already handles this. The rport was resumed if
the rport handed back matches the ndlp->nrport pointer. Otherwise,
devloss fired and the ndlp's nrport is NULL.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous logic would just drop the IO.
Added logic to queue the IO to wait for an IO context resource from an
IO thats already in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently IO resources are mapped 1 to 1 with RQ buffers posted
Added logic to separate RQE buffers from IO op resources
(sgl/iocbq/context). During initialization, the driver will determine
how many SGLs it will allocate for NVMET (based on what the firmware
reports) and associate a NVMET IOCBq and NVMET context structure with
each one.
Now that hdr/data buffers are immediately reposted back to the RQ, 512
RQEs for each MRQ is sufficient. Also, since NVMET data buffers are now
128 bytes, lpfc_nvmet_mrq_post is not necessary anymore as we will
always post the max (512) buffers per NVMET MRQ.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
