- Don't setup portdrv IRQs if there are no port drivers that use them, to
conserve vectors and avoid spurious events (Jan Kiszka)
* pci/portdrv:
PCI/portdrv: Do not setup up IRQs if there are no users
- Apply bus offset correctly in DMA address calculation, which used the
wrong sign before (Wang Lu)
* pci/p2pdma:
PCI/P2PDMA: Apply bus offset correctly in DMA address calculation
- Document sysfs "irq" attribute, which contains either the INTx IRQ (the
intended behavior) or the first MSI IRQ (historical mistake retained for
backwards compatibility) (Barry Song)
- Rework "irq" sysfs show function to explicitly fetch first MSI IRQ
instead of depending on core to put it in dev->irq, to enable future core
cleanup (Barry Song)
* pci/msi:
PCI/sysfs: Explicitly show first MSI IRQ for 'irq'
PCI: Document /sys/bus/pci/devices/.../irq
- Ignore Link Down/Up caused by error-induced Hot Reset so endpoint driver
can remain bound to device during error recovery (Lukas Wunner)
- Remove unused resume err_handler (Lukas Wunner)
- Remove unused pcie_port_bus_{,un}register() declarations (Lukas Wunner)
- Skip compiling err.c when CONFIG_PCIEAER not set (Lukas Wunner)
* pci/hotplug:
PCI/ERR: Reduce compile time for CONFIG_PCIEAER=n
PCI/portdrv: Remove unused pcie_port_bus_{,un}register() declarations
PCI/portdrv: Remove unused resume err_handler
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
- Drop the struct pci_dev.driver pointer, which is redundant with the
struct device.driver pointer (Uwe Kleine-König)
* pci/driver:
PCI: Remove struct pci_dev->driver
PCI: Use to_pci_driver() instead of pci_dev->driver
x86/pci/probe_roms: Use to_pci_driver() instead of pci_dev->driver
perf/x86/intel/uncore: Use to_pci_driver() instead of pci_dev->driver
powerpc/eeh: Use to_pci_driver() instead of pci_dev->driver
usb: xhci: Use to_pci_driver() instead of pci_dev->driver
cxl: Use to_pci_driver() instead of pci_dev->driver
cxl: Factor out common dev->driver expressions
xen/pcifront: Use to_pci_driver() instead of pci_dev->driver
xen/pcifront: Drop pcifront_common_process() tests of pcidev, pdrv
nfp: use dev_driver_string() instead of pci_dev->driver->name
mlxsw: pci: Use dev_driver_string() instead of pci_dev->driver->name
net: marvell: prestera: use dev_driver_string() instead of pci_dev->driver->name
net: hns3: use dev_driver_string() instead of pci_dev->driver->name
crypto: hisilicon - use dev_driver_string() instead of pci_dev->driver->name
powerpc/eeh: Use dev_driver_string() instead of struct pci_dev->driver->name
ssb: Use dev_driver_string() instead of pci_dev->driver->name
bcma: simplify reference to driver name
crypto: qat - simplify adf_enable_aer()
scsi: message: fusion: Remove unused mpt_pci driver .probe() 'id' parameter
PCI/ERR: Factor out common dev->driver expressions
PCI: Drop pci_device_probe() test of !pci_dev->driver
PCI: Drop pci_device_remove() test of pci_dev->driver
PCI: Return NULL for to_pci_driver(NULL)
- Rename pcibios_add_device() to pcibios_device_add() since it's called
from pci_device_add() (Oliver O'Halloran)
- Don't try to enable AtomicOps on VFs, since they can only be enabled on
the PF (Selvin Xavier)
* pci/enumeration:
PCI: Do not enable AtomicOps on VFs
PCI: Rename pcibios_add_device() to pcibios_device_add()
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Apple PCIe controller doesn't directly feed the endpoint's Requester ID
to the IOMMU (DART), but instead maps RIDs onto Stream IDs (SIDs). The DART
and the PCIe controller must thus agree on the SIDs that are used for
translation (by using the 'iommu-map' property).
For this purpose, parse the 'iommu-map' property each time a device gets
added, and use the resulting translation to configure the PCIe RID-to-SID
mapper. Similarly, remove the translation if/when the device gets removed.
This is all driven from a bus notifier which gets registered at probe time.
Hopefully this is the only PCI controller driver in the whole system.
[bhelgaas: squash indentation from Zhaoyu Liu <zackary.liu.pro@gmail.com>:
https://lore.kernel.org/r/20211031135544.GA1616@pc]
Link: https://lore.kernel.org/r/20210929163847.2807812-10-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Probe for the 'msi-ranges' property, and implement the MSI support in the
form of the usual two-level hierarchy.
Note that contrary to the wired interrupts, MSIs are shared among all the
ports.
Link: https://lore.kernel.org/r/20210929163847.2807812-8-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the per-port interrupt controller that deals with both INTx
signalling and management interrupts.
This allows the Link-up/Link-down interrupts to be wired, allowing the
bring-up to be synchronised (and provide debug information). The framework
can further be used to handle the rest of the per port events if and when
necessary.
Likewise, INTx signalling is implemented so that end-points can actually be
used.
Link: https://lore.kernel.org/r/20210929163847.2807812-7-maz@kernel.org
Link: https://lore.kernel.org/r/20211004150552.3844830-1-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that everything is in place at the poweroff sequence, this driver can
use module_platform_driver(), which allows it to be removed.
Link: https://lore.kernel.org/r/53b40494252444a9b830827922c4e3a301b8f863.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic under .remove ops is missing a call to dw_pcie_host_deinit(). Add
it, in order to allow the DWC core to be properly cleaned up.
Link: https://lore.kernel.org/r/838621e1c84ebaac153ccd9c36ea5e1254c61ead.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic at kirin_pcie_gpio_request() enables some clkreq GPIO lines.
Disable them during power-off.
Link: https://lore.kernel.org/r/f403e590843de1a581cade2d534d34715706f54e.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Instead of having two copies of the same logic, place the power-off logic
in a separate function.
No functional changes.
Link: https://lore.kernel.org/r/64f6e8da3e5fff38b6c8fcb208ace46efe6555bb.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
There's nothing preventing this driver from being loaded as a module.
Change its config from bool to tristate.
Link: https://lore.kernel.org/r/b5e7cfe9df09b492750bd6db0f0c911eaae8c2d4.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Apple's PCIe controller requires clocks to be configured in order to
bring up the hardware. Add the register pokes required to do so.
Adapted from Corellium's driver via Mark Kettenis's U-Boot patches.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-6-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
particularly the Apple M1. This driver exposes the internal bus used for
the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
radios requires additional drivers beyond what's necessary for PCIe itself.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-5-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Just as we now allow an interrupt map to be parsed when part of an
interrupt controller, there is no reason to ignore an interrupt map that
would be part of a pci device node such as a root port since we already
allow interrupt specifiers.
Allow the matching of such property when local to the node of a PCI
device, which allows the device itself to use the interrupt map for for
its own purpose.
Link: https://lore.kernel.org/r/20210929163847.2807812-4-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Host crashes when pci_enable_atomic_ops_to_root() is called for VFs with
virtual buses. The virtual buses added to SR-IOV have bus->self set to NULL
and host crashes due to this.
PID: 4481 TASK: ffff89c6941b0000 CPU: 53 COMMAND: "bash"
...
#3 [ffff9a9481713808] oops_end at ffffffffb9025cd6
#4 [ffff9a9481713828] page_fault_oops at ffffffffb906e417
#5 [ffff9a9481713888] exc_page_fault at ffffffffb9a0ad14
#6 [ffff9a94817138b0] asm_exc_page_fault at ffffffffb9c00ace
[exception RIP: pcie_capability_read_dword+28]
RIP: ffffffffb952fd5c RSP: ffff9a9481713960 RFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff89c6b1096000 RCX: 0000000000000000
RDX: ffff9a9481713990 RSI: 0000000000000024 RDI: 0000000000000000
RBP: 0000000000000080 R8: 0000000000000008 R9: ffff89c64341a2f8
R10: 0000000000000002 R11: 0000000000000000 R12: ffff89c648bab000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff89c648bab0c8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9a9481713988] pci_enable_atomic_ops_to_root at ffffffffb95359a6
#8 [ffff9a94817139c0] bnxt_qplib_determine_atomics at ffffffffc08c1a33 [bnxt_re]
#9 [ffff9a94817139d0] bnxt_re_dev_init at ffffffffc08ba2d1 [bnxt_re]
Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit in Device
Control 2 is reserved for VFs. The PF value applies to all associated VFs.
Return -EINVAL if pci_enable_atomic_ops_to_root() is called for a VF.
Link: https://lore.kernel.org/r/1631354585-16597-1-git-send-email-selvin.xavier@broadcom.com
Fixes: 35f5ace5de ("RDMA/bnxt_re: Enable global atomic ops if platform supports")
Fixes: 430a23689d ("PCI: Add pci_enable_atomic_ops_to_root()")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files
and scripts from Mauro. We are almost at the place where we
can properly check that the running kernel's sysfs abi is
documented fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPbjQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ync9gCfXKMUI1GAnCfJWAwTdTcd18q5akoAoMw32/AH
0yh5TjAWFyFd7xz5d7qs
=itsC
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
Here is the big set of staging driver updates and cleanups for 5.16-rc1.
Overall we ended up removing a lot of code this time, a bit over 20,000
lines are now gone thanks to a lot of cleanup work by many developers.
Nothing huge in here functionality wise, just loads of cleanups:
- r8188eu driver major cleanups and removal of unused and dead
code
- wlan-ng minor cleanups
- fbtft driver cleanups
- most driver cleanups
- rtl8* drivers cleanups
- rts5208 driver cleanups
- vt6655 driver cleanups
- vc04_services drivers cleanups
- wfx cleanups on the way to almost getting this merged out of
staging (it's close!)
- tiny mips changes needed for the mt7621 drivers, they have
been acked by the respective subsystem maintainers to go
through this tree.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPZQQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yml9wCeJl83anYno0xh+UP6CsEkbe64VJEAoIEKyry/
tlUowcatxGfz3aYA1wTc
=FyAK
-----END PGP SIGNATURE-----
Merge tag 'staging-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates and cleanups for
5.16-rc1.
Overall we ended up removing a lot of code this time, a bit over
20,000 lines are now gone thanks to a lot of cleanup work by many
developers.
Nothing huge in here functionality wise, just loads of cleanups:
- r8188eu driver major cleanups and removal of unused and dead code
- wlan-ng minor cleanups
- fbtft driver cleanups
- most driver cleanups
- rtl8* drivers cleanups
- rts5208 driver cleanups
- vt6655 driver cleanups
- vc04_services drivers cleanups
- wfx cleanups on the way to almost getting this merged out of
staging (it's close!)
- tiny mips changes needed for the mt7621 drivers, they have been
acked by the respective subsystem maintainers to go through this
tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (622 commits)
staging: r8188eu: hal: remove goto statement and local variable
staging: rtl8723bs: hal remove the assignment to itself
staging: rtl8723bs: fix unmet dependency on CRYPTO for CRYPTO_LIB_ARC4
staging: vchiq_core: get rid of typedef
staging: fieldbus: anybus: reframe comment to avoid warning
staging: r8188eu: fix missing unlock in rtw_resume()
staging: r8188eu: core: remove the goto from rtw_IOL_accquire_xmit_frame
staging: r8188eu: core: remove goto statement
staging: vt6655: Rename `dwAL7230InitTable` array
staging: vt6655: Rename `dwAL2230PowerTable` array
staging: vt6655: Rename `dwAL7230InitTableAMode` array
staging: vt6655: Rename `dwAL7230ChannelTable2` array
staging: vt6655: Rename `dwAL7230ChannelTable1` array
staging: vt6655: Rename `dwAL7230ChannelTable0` array
staging: vt6655: Rename `dwAL2230ChannelTable1` array
staging: vt6655: Rename `dwAL2230ChannelTable0` array
staging: r8712u: fix control-message timeout
staging: rtl8192u: fix control-message timeouts
staging: mt7621-dts: add missing SPDX license to files
staging: vchiq_core: fix quoted strings split across lines
...
We already include <linux/device.h> and <linux/msi.h>, which
include <asm/device.h> and <asm/msi.h>.
Drop the redundant includes of <asm/device.h> and <asm/msi.h>.
[bhelgaas: squash in fix from Wan Jiabing <wanjiabing@vivo.com>:
https://lore.kernel.org/r/20211104063720.29375-1-wanjiabing@vivo.com]
Link: https://lore.kernel.org/r/20211013003145.1107148-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce7 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Use the preferred generic header file linux/io.h that already includes the
corresponding asm/io.h file.
Link: https://lore.kernel.org/r/20211013003145.1107148-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Merge PCI device power management updates for 5.16-rc1:
- Make the association of ACPI device objects with PCI devices more
straightforward and simplify the code doing that for all devices
in general (Rafael Wysocki).
- Eliminate struct pci_platform_pm_ops and handle the both of its
users (PCI and Intel MID) directly in the PCI bus code (Rafael
Wysocki).
- Simplify and clarify ACPI PCI device PM helpers (Rafael Wysocki).
- Fix ordering of operations in pci_back_from_sleep() (Rafael
Wysocki).
* pm-pci:
PCI: PM: Fix ordering of operations in pci_back_from_sleep()
PCI: PM: Do not call platform_pci_power_manageable() unnecessarily
PCI: PM: Make pci_choose_state() call pci_target_state()
PCI: PM: Rearrange pci_target_state()
PCI: PM: Simplify acpi_pci_power_manageable()
PCI: PM: Drop struct pci_platform_pm_ops
PCI: ACPI: PM: Do not use pci_platform_pm_ops for ACPI
PCI: PM: Do not use pci_platform_pm_ops for Intel MID PM
ACPI: glue: Look for ACPI bus type only if ACPI companion is not known
ACPI: glue: Drop cleanup callback from struct acpi_bus_type
PCI: ACPI: Drop acpi_pci_bus
The PHY layer need to access APB registers too, for Kirin 970. So place
them into a named regmap.
Link: https://lore.kernel.org/r/daf0e4bda5a69a5ac8484e70f09351a959805c8c.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin driver contains both PHY and generic PCI driver.
The best would be, instead, to support a PCI PHY driver, making the driver
more generic.
However, it is too late to remove the Kirin 960 PHY, as a change like that
would make the DT schema incompatible with past versions.
So, add support for an external PHY driver without removing the existing
Kirin 960 PHY from it.
Link: https://lore.kernel.org/r/f38361df2e9d0dc5a38ff942b631f7fef64cdc12.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin PCIe driver contains internally a PHY interface for
Kirin 960.
As the next patches will add support for using an external PHY driver,
reorganize the driver in a way that the PHY part will be self-contained.
This could be moved to a separate PHY driver, but a change like that would
mean a non-backward-compatible DT schema change.
Link: https://lore.kernel.org/r/ad2f4aa6bbb71d5c9af0139704672f75f12644fc.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Add pci_find_dvsec_capability to locate a Designated Vendor-Specific
Extended Capability with the specified Vendor ID and Capability ID.
The Designated Vendor-Specific Extended Capability (DVSEC) allows one or
more "vendor" specific capabilities that are not tied to the Vendor ID
of the PCI component. Where the DVSEC Vendor may be a standards body
like CXL.
Cc: David E. Box <david.e.box@linux.intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-pci@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163379787943.692348.6814373487017444007.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Aardvark supports PCIe Hot Reset via PCIE_CORE_CTRL1_REG.
Use it for implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL
register on emulated bridge.
With this, the function pci_reset_secondary_bus() starts working and can
reset connected PCIe card. Custom userspace script [1] which uses setpci
can trigger PCIe Hot Reset and reset the card manually.
[1] https://alexforencich.com/wiki/en/pcie/hot-reset-linux
Link: https://lore.kernel.org/r/20211028185659.20329-7-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b68
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
The bare "unsigned" type implicitly means "unsigned int", but the preferred
coding style is to use the complete type name.
Update the bare use of "unsigned" to the preferred "unsigned int".
No change to functionality intended.
See a1ce18e4f9 ("checkpatch: warn on bare unsigned or signed declarations
without int").
Link: https://lore.kernel.org/r/20211013014136.1117543-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The variable 'rc' is being initialized with a value that is never read.
Remove the redundant assignment.
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210910161417.91001-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Add driver for the PCIe controller of the MT7621 SoC.
[bhelgaas: rename from pci-mt7621.c to pcie-mt7621.c; also rename Kconfig
symbol from PCI_MT7621 to PCIE_MT7621]
Link: https://lore.kernel.org/r/20210922050035.18162-3-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ordering of operations in pci_back_from_sleep() is incorrect,
because the device may be in D3cold when it runs and pci_enable_wake()
needs to access the device's configuration space which cannot be
done in D3cold.
Fix this by calling pci_set_power_state() to put the device into D0
before calling pci_enable_wake() for it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r5.0, sec 7.5.3.16, Downstream Ports must disable LTR if the link
goes down (the Port goes DL_Down status). This is a problem because the
Downstream Port's dev->ltr_path is still set, so we think LTR is still
enabled, and we enable LTR in the Endpoint. When it sends LTR messages,
they cause Unsupported Request errors at the Downstream Port.
This happens in the reset path, where we may enable LTR in
pci_restore_pcie_state() even though the Downstream Port disabled LTR
because the reset caused a link down event.
It also happens in the hot-remove and hot-add path, where we may enable LTR
in pci_configure_ltr() even though the Downstream Port disabled LTR when
the hot-remove took the link down.
In these two scenarios, check the upstream bridge and restore its LTR
enable if appropriate.
The Unsupported Request may be logged by AER as follows:
pcieport 0000:00:1d.0: AER: Uncorrected (Non-Fatal) error received: id=00e8
pcieport 0000:00:1d.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=00e8(Requester ID)
pcieport 0000:00:1d.0: device [8086:9d18] error status/mask=00100000/00010000
pcieport 0000:00:1d.0: [20] Unsupported Request (First)
In addition, if LTR is not configured correctly, the link cannot enter the
L1.2 state, which prevents some machines from entering the S0ix low power
state.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211012075614.54576-1-mingchuang.qiao@mediatek.com
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mingchuang Qiao <mingchuang.qiao@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The sysfs "irq" file contains the legacy INTx IRQ. Or, if the device has
MSI enabled, it contains the first MSI IRQ instead.
Previously this file showed the pci_dev.irq value directly. But we'd
prefer to use pci_dev.irq only for the INTx IRQ and decouple that from any
MSI or MSI-X IRQs.
If the device has MSI enabled, explicitly look up and show the first MSI
IRQ in the sysfs "irq" file. Otherwise, show the INTx IRQ.
This removes the requirement that msi_capability_init() set pci_dev.irq to
the first MSI IRQ when enabling MSI and pci_msi_shutdown() restore the INTx
IRQ when disabling MSI.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210825102636.52757-3-21cnbao@gmail.com
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pci_dev->driver with to_pci_driver(). This is a step toward
removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sole non-static function in err.c, pcie_do_recovery(), is only
called from:
* aer.c (if CONFIG_PCIEAER=y)
* dpc.c (if CONFIG_PCIE_DPC=y, which depends on CONFIG_PCIEAER)
* edr.c (if CONFIG_PCIE_EDR=y, which depends on CONFIG_PCIE_DPC)
Thus, err.c need not be compiled if CONFIG_PCIEAER=n.
Also, pci_uevent_ers() and pcie_clear_device_status(), which are called
from err.c, can be #ifdef'ed away unless CONFIG_PCIEAER=y.
Since x86_64_defconfig doesn't enable CONFIG_PCIEAER, this change may
slightly reduce compile time for anyone doing a test build with that
config.
Link: https://lore.kernel.org/r/98f9041151268c1c035ab64cca320ad86803f64a.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 3e41a317ae ("PCI/AER: Remove unused aer_error_resume()")
removed the resume err_handler from AER. Since no other port service
implements the callback, support for it can be removed from portdrv.
It can be revived later if need be, preferably by re-using the
pcie_port_device_iter() iterator.
Link: https://lore.kernel.org/r/25334149b604e005058aeb0fdf51e01f991d5d74.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <kbusch@kernel.org>
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pdev->driver with to_pci_driver(). This is a step toward removing
pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
pcifront_common_process() exits early if pcidev or pcidev->driver are NULL,
so simplify it by not checking them again.
[bhelgaas: split flag change to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
On the SC7280, the clock source for gcc_pcie_1_pipe_clk_src must be the
TCXO while gdsc is enabled. After PHY init successful clock source should
switch to pipe clock for gcc_pcie_1_pipe_clk_src.
Link: https://lore.kernel.org/r/1633628923-25047-6-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Add struct qcom_pcie_cfg as match data for all platforms. Assign
appropriate platform ops into struct qcom_pcie_cfg and read using
of_device_get_match_data() in qcom_pcie_probe().
Link: https://lore.kernel.org/r/1633628923-25047-5-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Not all events are supported by every gen/variant of the Switchtec
firmware. To solve this, since Gen4, a new bit in each event header
is introduced to indicate if an event is supported by the firmware.
Link: https://lore.kernel.org/r/20211014141859.11444-6-kelvin.cao@microchip.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ENOTSUPP is not a SUSV4 error code, and the following checkpatch.pl
warning will be given for new patches which still use ENOTSUPP.
WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
See the link below for the discussion.
https://lore.kernel.org/netdev/20200511165319.2251678-1-kuba@kernel.org/
Replace ENOTSUPP with EOPNOTSUPP to align with future patches which will
be using EOPNOTSUPP.
Link: https://lore.kernel.org/r/20211014141859.11444-5-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gen4 firmware adds DMA VEP and NVMe VEP support in VEP (virtual EP)
instance ID register in addtion to management EP, update the way of
getting management VEP instance ID.
Link: https://lore.kernel.org/r/20211014141859.11444-4-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If an error is encountered when executing a MRPC command, the firmware
will set the status register to SWITCHTEC_MRPC_STATUS_ERROR and return
the error code in the return value register.
Add handling of SWITCHTEC_MRPC_STATUS_ERROR on status register when
completing a MRPC command.
Link: https://lore.kernel.org/r/20211014141859.11444-3-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A firmware hard reset may be initiated by various mechanisms including a
UART interface, TWI sideband interface from BMC, MRPC command from
userspace, etc. The switchtec management driver is unaware of these
resets.
The reset clears PCI state including the BARs and Memory Space Enable
bits, so the device no longer responds to the MMIO accesses the driver
uses to operate it.
MMIO reads to the device will fail with a PCIe error. When the root
complex handles that error, it typically fabricates ~0 data to complete
the CPU read.
Check for this sort of error by reading the device ID from MMIO space.
This ID can never be ~0, so if we see that value, it probably means the
PCIe Memory Read failed and we should return an error indication to the
application using the switchtec driver.
Link: https://lore.kernel.org/r/20211014141859.11444-2-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With UML having enabled (simulated) PCI on UML, VMD breaks
allyesconfig/allmodconfig compilation because it assumes
it's running on X86_64 bare metal, and has hardcoded API
use of ARCH=x86. Make it depend on !UML to fix this.
Link: https://lore.kernel.org/r/20210811162530.affe26231bc3.I131b3c1e67e3d2ead6e98addd256c835fbef9a3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
The code block related to the if-statement in cpqhp_set_irq() is
somewhat awkwardly formatted making the code hard to read.
Make it readable. No change to functionality intended.
Link: https://lore.kernel.org/r/20211013011412.1110829-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, when msi_populate_sysfs() failed, we saved the error return
value as dev->msi_irq_groups, which leads to a page fault when
free_msi_irqs() calls msi_destroy_sysfs().
To prevent this, leave dev->msi_irq_groups alone when msi_populate_sysfs()
fails.
Found by the Hulk Robot when injecting a memory allocation fault in
msi_populate_sysfs():
BUG: unable to handle page fault for address: fffffffffffffff4
...
Call Trace:
msi_destroy_sysfs+0x30/0xa0
free_msi_irqs+0x11d/0x1b0
Fixes: 2f170814bd ("genirq/msi: Move MSI sysfs handling from PCI to MSI core")
Link: https://lore.kernel.org/r/20211012071556.939137-1-wanghai38@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Barry Song <song.bao.hua@hisilicon.com>
Save the struct pci_driver pointer from pdev->driver instead of repeating
it several times. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When the device core calls the .probe() callback for a device, the device
is never bound, so pci_dev->driver is always NULL.
Remove the unnecessary test of !pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When the driver core calls pci_device_remove(), there is a driver bound
to the device, so pci_dev->driver is never NULL.
Remove the unnecessary test of pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cppcheck warns that pci_dev_str_match_path() passes pointers to signed ints
to sscanf("%x"), which expects pointers to *unsigned* ints:
invalidScanfArgType_int drivers/pci/pci.c:312 %x in format string (no. 2) requires 'unsigned int *' but the argument type is 'signed int *'.
Declare the variables as unsigned to avoid this issue.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211008222732.2868493-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"dom_req" is a u16 but varargs automatically promotes it to int, so there's
no point in using the %h modifier. Drop it.
See cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]") and 70eb2275ff ("checkpatch: add
warning for unnecessary use of %h[xudi] and %hh[xudi]").
Link: https://lore.kernel.org/r/20211008222732.2868493-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When enabling VMD in BIOS setup (Ice Lake Processor: Whitley platform),
the host OS cannot boot successfully with the following error message:
nvme nvme0: I/O 12 QID 0 timeout, completion polled
nvme nvme0: Shutdown timeout set to 6 seconds
DMAR: DRHD: handling fault status reg 2
DMAR: [INTR-REMAP] Request device [0x00:0x00.5] fault index 0xa00 [fault reason 0x25] Blocked a compatibility format interrupt request
The request device is the VMD controller:
# lspci -s 0000:00.5 -nn
0000:00:00.5 RAID bus controller [0104]: Intel Corporation Volume
Management Device NVMe RAID Controller [8086:28c0] (rev 04)
`git bisect` points to this offending commit ee81ee84f8 ("PCI:
vmd: Disable MSI-X remapping when possible"), which disables VMD MSI
remapping. The IOMMU hardware blocks the compatibility format
interrupt request because Interrupt Remapping Enable Status (IRES) and
Extended Interrupt Mode Enable (EIME) are enabled. Please refer to
section "5.1.4 Interrupt-Remapping Hardware Operation" in Intel VT-d
spec.
To fix the issue, VMD driver still enables the interrupt remapping
irrespective of VMD_FEAT_CAN_BYPASS_MSI_REMAP if the IOMMU subsystem
enables the interrupt remapping.
Test configuration is shown as follows:
* Two VMD controllers
1. 8086:28c0 (Whitley's VMD)
2. 8086:201d (Purley's VMD: The issue does not appear in this
controller. Just make sure if any side effect occurs.)
* w/wo intremap=off
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214219
Link: https://lore.kernel.org/r/20210901124047.1615-1-adrianhuang0701@gmail.com
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Cc: Jon Derrick <jonathan.derrick@intel.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
On the Qualcomm sc8180x platform the bootloader does something related
to PCI that leaves a pending "msi" interrupt, which with the current
ordering often fires before init has a chance to enable the clocks that
are necessary for the interrupt handler to access the hardware.
Move the host_init() call before the registration of the "msi" interrupt
handler to ensure the host driver has a chance to enable the clocks.
The assignment of the bridge's ops and child_ops is moved along, because
at least the TI Keystone driver overwrites these in its host_init
callback.
Link: https://lore.kernel.org/r/20210823154958.305677-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Qualcomm PCIe Endpoint controller based on the DesignWare
core with added Qualcomm-specific wrapper around the core. The driver
support is very basic such that it supports only enumeration, PCIe
read/write, and MSI. There is no ASPM and PM support for now but these will
be added later.
The driver is capable of using the PERST# and WAKE# side-band GPIOs for
operation and written on top of the DWC PCI framework.
[bhelgaas: wrap a few long lines]
Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: restructured the driver and fixed several bugs for upstream]
Link: https://lore.kernel.org/r/20210920065946.15090-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
In certain cases we need a variant of pci_read_vpd()/pci_write_vpd() that
does not check against dev->vpd.len. Such cases are:
- Reading VPD if dev->vpd.len isn't set yet (in pci_vpd_size())
- Devices that map non-VPD information to arbitrary places in VPD address
space (example: Chelsio T3 EEPROM write-protect flag)
Therefore add pci_read_vpd_any() and pci_write_vpd_any() that check against
PCI_VPD_MAX_SIZE only.
Link: https://lore.kernel.org/r/93ecce28-a158-f02a-d134-8afcaced8efe@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
- Fix potential memory leak on a error path in eBPF.
- Fix handling of zpci device on reserve.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmFg0FoACgkQjYWKoQLX
FBg3jgf8DLCs6JwK8GOz40CuZsajARwuagZy0udc3GbcZVNUog6GP7hJBU6q8pkm
JQMTl1C7Pe81p/aTOx2IIplV+owAVRnwdNBmj/psmZrI5P0CvLtTc4gVuCZJHJy4
9qt83KocgrN4G2K7qZDfiEAv+Ae/F7r20K5ZBX0exZBkOFeXZzUYVwWxM3pV45XB
Zx5AWmpHGGZFaS3EKW7E5VqswlGYIfUzGaXezN/cIl5HzMqqQMYo77eCJAWr//1z
s2s+vvEUBLGuHS8pDdXq8qR7Fq93cJSS7eo5zLVgtyZHr3Nn3+IlA0WKmPU3SmPE
+19I3L5hR0Ap6xh4ASgxciexnXFttQ==
=bGB2
-----END PGP SIGNATURE-----
Merge tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems.
-----BEGIN PGP SIGNATURE-----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=H0kg
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems"
* tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
Remove includes that are not needed, to speed up (re)compilation.
Most of these are relics from splitting the driver in a host and a
common part.
[bhelgaas: use driver tag analogous to rcar-ep]
Link: https://lore.kernel.org/r/54bed9a0e6991490ddb2b07e5abfaf40a7a62928.1633090577.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Remove includes that are not needed, to speed up (re)compilation. Include
<linux/pm_runtime.h>, which is needed, and was included implicitly through
<linux/phy/phy.h> before.
Most of these are relics from splitting the driver in a host and a common
part and adding endpoint support.
[bhelgaas: use driver tag consistent with cadence-ep, designware-ep]
Link: https://lore.kernel.org/r/7c708841a2bf84f85b14a963271c3e99c8ba38a5.1633090444.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmFeykwTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXhRLCADXOOSGKk4L1vWssRRhLmMXI45ElocY
EbZ/mXcQhxKnlVhdMNnupGjz+lU5FQGkCCWlhmt9Ml2O6R+lDx+zIUS8BK3Nkom9
twWjueMtum6yFwDMGYALhptVLjDqVFG71QcW0incghpnAx4s2FVE8h38md5MuUFY
Kqqf/dRkppSePldHFrRG/e4c6r0WyTsJ6Z9LTU0UYp5GqJcmUJlx7TxxqzGk5Fti
GpQ5cFS7JX8xHAkRROk/dvwJte1RRnBAW6lIWxwAaDJ6Gbg7mNfOQe7n+/KRO7ZG
gC5hbkP9tMv2nthLxaFbpu791U4lMZ2WiTLZvbgCseO3FCmToXWZ6TDd
=1mdq
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Replace uuid.h with types.h in a header (Andy Shevchenko)
- Avoid sleeping in atomic context in PCI driver (Long Li)
- Avoid sending IPI to self when it shouldn't (Vitaly Kuznetsov)
* tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Avoid erroneously sending IPI to 'self'
hyper-v: Replace uuid.h with types.h
PCI: hv: Fix sleep while in non-sleep context when removing child devices from the bus
If acpi_pci_find_companion() is called for a device whose parent
pointer is NULL, it will crash when attempting to get the ACPI
companion of the parent due to a NULL pointer dereference in
the ACPI_COMPANION() macro.
This was not a problem before commit 375553a932 ("PCI: Setup ACPI
fwnode early and at the same time with OF") that made pci_setup_device()
call pci_set_acpi_fwnode() and so it allowed devices with NULL parent
pointers to be passed to acpi_pci_find_companion() which is the case
in pci_iov_add_virtfn(), for instance.
Fix this issue by making acpi_pci_find_companion() check the device's
parent pointer upfront and bail out if it is NULL.
While pci_iov_add_virtfn() can be changed to set the device's parent
pointer before calling pci_setup_device() for it, checking pointers
against NULL before dereferencing them is prudent anyway and looking
for ACPI companions of virtual functions isn't really useful.
Fixes: 375553a932 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/linux-acpi/8e4bbd5c59de31db71f718556654c0aa077df03d.camel@linux.ibm.com/
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
If the system has multiple VMD controllers, the driver does not assign
a number to each controller, so when analyzing the interrupt through
/proc/interrupts, the names of all controllers are the same, which is
not very convenient for problem analysis. Here, try to assign a number
to each VMD controller.
Link: https://lore.kernel.org/r/1631884404-24141-1-git-send-email-brookxu.cn@gmail.com
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Clean up the users of PCIE_DW_EP and introduce idiom
depends on PCI_ENDPOINT
select PCIE_DW_EP
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Furthermore, there is no need to repeat menu dependencies (PCI).
Clean up the users of PCIE_DW_HOST and introduce idiom
depends on PCI_MSI_IRQ_DOMAIN
select PCIE_DW_HOST
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
Link: https://lore.kernel.org/r/20211005180952.6812-14-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
PCIe config space can be initialized also before pci_bridge_emul_init()
call, so move rootcap initialization after PCI config space initialization.
This simplifies the function a little since it removes one if (ret < 0)
check.
Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Avoid code repetition in advk_pcie_rd_conf() by handling errors with
goto jump, as is customary in kernel.
Link: https://lore.kernel.org/r/20211005180952.6812-9-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Use the proper macro instead of hard-coded (-1) value.
Suggested-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Link: https://lore.kernel.org/r/20211004133453.18881-2-mgurtovoy@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop two invocations of platform_pci_power_manageable() that are not
necessary, because the functions called when it returns 'true' do the
requisite "power manageable" checks themselves.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
The pci_choose_state() and pci_target_state() implementations are
somewhat divergent without a good reason, because they are used
for similar purposes.
Change the pci_choose_state() implementation to use pci_target_state()
internally except for transitions to the working state of the system
in which case it is expected to return D0.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Make pci_target_state() return D3cold or D0 without checking PME
support if the current power state of the device is D3cold or if it
does not support the standard PCI PM, respectively.
Next, drop the tergat_state local variable that has become redundant
from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Make acpi_pci_power_manageable() more straightforward.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
After previous changes there are no more users of struct
pci_platform_pm_ops in the tree, so drop it along with all of the
remaining related code.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
pci_remap_iospace() was originally meant as an architecture specific helper
but it moved into generic code after all architectures had the same
requirements. MIPS has different requirements so it should not be shared.
The way for doing this will be using a macro 'pci_remap_iospace' defined
for those architectures that need a special treatment. Hence, put core API
function inside preprocesor conditional code for 'pci_remap_iospace'
definition.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210925203224.10419-5-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.
Code refactoring completed in the commit 39bc500650 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".
Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.
Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert sprintf() in sysfs "show" functions to sysfs_emit() in order to
check for buffer overruns in sysfs outputs.
Link: https://lore.kernel.org/r/1630472957-26857-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Header file linux/pci_ids.h defines AMCC vendor id (0x10e8) macro named
PCI_VENDOR_ID_AMCC. So use this macro instead of driver custom macro.
Link: https://lore.kernel.org/r/20210927134356.11799-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
If the clock is provided externally we need to make sure it is enabled
before starting PCI scan.
Link: https://lore.kernel.org/r/20210531085934.2662457-5-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Unused since commit e259c2926c ("PCI: pci-dra7xx: Prepare for deferred
probe with module_platform_driver").
Link: https://lore.kernel.org/r/20210531085934.2662457-4-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable building the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20210531085934.2662457-3-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Built-in graphics at 07:00.0 on HP EliteDesk 805 G6 doesn't work because
graphics can't get the BAR it needs. The BIOS configuration is
correct: BARs 0 and 2 both fit in the 00:08.1 bridge window.
But that 00:08.1 window covers two host bridge apertures from _CRS.
Previously we assumed this was illegal, so we clipped the window to fit
into one aperture (see 0f7e7aee2f ("PCI: Add pci_bus_clip_resource() to
clip to fit upstream window")).
pci_bus 0000:00: root bus resource [mem 0x10020200000-0x100303fffff window]
pci_bus 0000:00: root bus resource [mem 0x10030400000-0x100401fffff window]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100401fffff 64bit pref]
pci 0000:07:00.0: reg 0x10: [mem 0x10030000000-0x1003fffffff 64bit pref]
pci 0000:07:00.0: reg 0x18: [mem 0x10040000000-0x100401fffff 64bit pref]
pci 0000:00:08.1: can't claim BAR 15 [mem 0x10030000000-0x100401fffff 64bit pref]: no compatible bridge window
pci 0000:00:08.1: [mem 0x10030000000-0x100401fffff 64bit pref] clipped to [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:07:00.0: can't claim BAR 0 [mem 0x10030000000-0x1003fffffff 64bit pref]: no compatible bridge window
pci 0000:07:00.0: can't claim BAR 2 [mem 0x10040000000-0x100401fffff 64bit pref]: no compatible bridge window
However, the host bridge apertures are contiguous, so there's no need to
clip in this case. Coalesce contiguous apertures so we can allocate from
the entire contiguous region.
Previous commit 65db04053e ("PCI: Coalesce host bridge contiguous
apertures") was similar but sorted the apertures, and Guenter Roeck
reported a regression in ppc:sam460ex qemu emulation from nvme; see
https://lore.kernel.org/all/20210709231529.GA3270116@roeck-us.net/
[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212013
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210713125007.1260304-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Using struct pci_platform_pm_ops for ACPI adds unnecessary
indirection to the interactions between the PCI core and ACPI PM,
which is also subject to retpolines.
Moreover, it is not particularly clear from the current code that,
as far as PCI PM is concerned, "platform" really means just ACPI
except for the special casess when Intel MID PCI PM is used or when
ACPI support is disabled (through the kernel config or command line,
or because there are no usable ACPI tables on the system).
To address the above, rework the PCI PM code to invoke ACPI PM
functions directly as needed and drop the acpi_pci_platform_pm
object that is not necessary any more.
Accordingly, update some of the ACPI PM functions in question to do
extra checks in case the ACPI support is disabled (which previously
was taken care of by avoiding to set the pci_platform_ops pointer
in those cases).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
strtobool() is a wrapper around kstrtobool() that has been added for
backward compatibility.
There is no reason to use the old API, so use kstrtobool() directly.
Related: ef95159907 ("lib: move strtobool() to kstrtobool()")
Link: https://lore.kernel.org/r/20210915230127.2495723-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most of the "store" functions that handle userspace input via sysfs return
-EINVAL should the value fail validation and/or type conversion. This
error code is a clear message to userspace that the value is not a valid
input.
However, some of the "show" functions return input parsing error codes
as-is, which may be either -EINVAL or -ERANGE. The former would often be
from kstrtobool(), and the latter typically from other kstr*() functions
such as kstrtou8(), kstrtou32(), kstrtoint(), etc.
-EINVAL is commonly returned as the error code to indicate that the value
provided is invalid, but -ERANGE is not very useful in userspace.
Therefore, normalize the return error code to be -EINVAL for when the
validation and/or type conversion fails.
Link: https://lore.kernel.org/r/20210915230127.2495723-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check if the "CAP_SYS_ADMIN" capability flag is set before parsing user
input as it makes more sense to first check whether the current user
actually has the right permissions before accepting any input from such
user.
This will also make order in which enable_store() and msi_bus_store()
perform the "CAP_SYS_ADMIN" capability check consistent with other
PCI-related sysfs objects that first verify whether user has this
capability set.
Link: https://lore.kernel.org/r/20210915230127.2495723-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are only two users of struct pci_platform_pm_ops in the tree,
one of which is Intel MID PM and the other one is ACPI. They are
mutually exclusive and the MID PM should take precedence when they
both are enabled, but whether or not this really is the case hinges
on the specific ordering of arch_initcall() calls made by them.
The struct pci_platform_pm_ops abstraction is not really necessary
for just these two users, but it adds complexity and overhead because
of retoplines involved in using all of the function pointers in there.
It also makes following the code a bit more difficult than it would
be otherwise.
Moreover, Intel MID PCI PM doesn't even implement the majority of the
function pointers in struct pci_platform_pm_ops in a meaningful way,
so switch over the PCI core to calling the relevant MID PM routines,
mid_pci_set_power_state() and mid_pci_set_power_state(), directly as
needed and drop mid_pci_platform_pm.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
The acpi_pci_bus structure was used primarily for running
acpi_pci_find_companion() during PCI device objects registration,
but after commit 375553a932 ("PCI: Setup ACPI fwnode early and at
the same time with OF") that function is called by pci_setup_device()
via pci_set_acpi_fwnode(), which happens before calling
pci_device_add() on the new PCI device object, so its ACPI companion
has been set already when acpi_device_notify() runs and it will never
call ->find_companion() from acpi_pci_bus.
For this reason, modify acpi_device_notify() and
acpi_device_notify_remove() to call pci_acpi_setup() and
pci_acpi_cleanup(), respectively, directly on PCI device objects
and drop acpi_pci_bus altogether.
While at it, notice that pci_acpi_setup() and pci_acpi_cleanup()
can obtain the ACPI companion pointer, which is guaranteed to not
be NULL, from their callers and modify them to work that way so
as to reduce the number of redundant checks somewhat.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYU8xegAKCRCAXGG7T9hj
vvk2APwM85dFSMNHQo5+S35X+h+M8uKuqqvPYxVtKqQEwu3LXAEAg0cVgr1lWegI
X98f07/+M0rPJl24kgW/EIxAD9fsWAw=
=JILz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some minor cleanups and fixes of some theoretical bugs, as well as a
fix of a bug introduced in 5.15-rc1"
* tag 'for-linus-5.15b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/x86: fix PV trap handling on secondary processors
xen/balloon: fix balloon kthread freezing
swiotlb-xen: this is PV-only on x86
xen/pci-swiotlb: reduce visibility of symbols
PCI: only build xen-pcifront in PV-enabled environments
swiotlb-xen: ensure to issue well-formed XENMEM_exchange requests
Xen/gntdev: don't ignore kernel unmapping error
xen/x86: drop redundant zeroing from cpu_initialize_context()
In hv_pci_bus_exit, the code is holding a spinlock while calling
pci_destroy_slot(), which takes a mutex.
This is not safe for spinlock. Fix this by moving the children to be
deleted to a list on the stack, and removing them after spinlock is
released.
Fixes: 94d2276320 ("PCI: hv: Fix a race condition when removing the device")
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/linux-hyperv/20210823152130.GA21501@kili/
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/1630365207-20616-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The general convention for pcibios_* hooks is that they're named after the
corresponding pci_* function they provide a hook for. The exception is
pcibios_add_device() which provides a hook for pci_device_add().
Rename pcibios_add_device() to pcibios_device_add() so it matches
pci_device_add().
Also, remove the export of the microblaze version. The only caller must be
compiled as a built-in so there's no reason for the export.
Link: https://lore.kernel.org/r/20210913152709.48013-1-oohall@gmail.com
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com> # s390
Avoid registering service IRQs if there is no service that offers them
or no driver to register a handler against them. This saves IRQ vectors
when they are limited (e.g. on x86) and also avoids that spurious events
could hit a missing handler. Such spurious events need to be generated
by the Jailhouse hypervisor for active MSI vectors when enabling or
disabling itself.
Link: https://lore.kernel.org/r/8f9a13ac-8ab1-15ac-06cb-c131b488a36f@siemens.com
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.
Add a quirk to avoid bus resets on this device, which avoids the hang.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein <ingmar_klein@web.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
The bus offset is bus address - physical address, so the calculation in
__pci_p2pdma_map_sg should be: bus address = physical address + bus offset.
Correct the dma_address computation in __pci_p2pdma_map_sg().
Link: https://lore.kernel.org/r/20210909032528.24517-1-wanglu@dapustor.com
Signed-off-by: Wang Lu <wanglu@dapustor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The driver's module init function, pcifront_init(), invokes
xen_pv_domain() first thing. That construct produces constant "false"
when !CONFIG_XEN_PV. Hence there's no point building the driver in
non-PV configurations.
Drop the (now implicit and generally wrong) X86 dependency: At present,
XEN_PV can only be set when X86 is also enabled. In general an
architecture supporting Xen PV (and PCI) would want to have this driver
built.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/3a7f6c9b-215d-b593-8056-b5fe605dafd7@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Some AMD GPUs have built-in USB xHCI and USB Type-C UCSI controllers with
power dependencies between the GPU and the other functions as in
6d2e369f0d ("PCI: Add NVIDIA GPU multi-function power dependencies").
Add device link support for the AMD integrated USB xHCI and USB Type-C UCSI
controllers.
Without this, runtime power management, including GPU resume and temp and
fan sensors don't work correctly.
Reported-at: https://gitlab.freedesktop.org/drm/amd/-/issues/1704
Link: https://lore.kernel.org/r/20210903063311.3606226-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Commit 375553a932 ("PCI: Setup ACPI fwnode early and at the same time
with OF") added a call to pci_set_acpi_fwnode() in pci_setup_device(),
which unconditionally clears any fwnode previously set by
pci_set_of_node().
pci_set_acpi_fwnode() looks for ACPI_COMPANION(), which only returns the
existing fwnode if it was set by ACPI_COMPANION_SET(). If it was set by
OF instead, ACPI_COMPANION() returns NULL and pci_set_acpi_fwnode()
accidentally clears the fwnode. To fix this, look for any fwnode instead
of just ACPI companions.
Fixes a virtio-iommu boot regression in v5.15-rc1.
Fixes: 375553a932 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/r/20210913172358.1775381-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()") reads VPD at
enumeration-time to find the size. But this is quite slow, and we don't
need the size until we actually need data from VPD. Dave reported a boot
slowdown of more than two minutes [1].
Defer the VPD sizing until a driver or the user (via sysfs) requests
information from VPD.
If devices are quirked because VPD is known not to work, don't bother even
looking for the VPD capability. The VPD will not be accessible at all.
[1] https://lore.kernel.org/r/20210913141818.GA27911@codemonkey.org.uk/
Link: https://lore.kernel.org/r/20210914215543.GA1437800@bjorn-Precision-5520
Fixes: 7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add ACPI support to the PCI VMD driver (Rafael Wysocki).
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello).
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----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=8lPe
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add ACPI support to the PCI VMD driver, improve suspend-to-idle
support for AMD platforms and update documentation.
Specifics:
- Add ACPI support to the PCI VMD driver (Rafael Wysocki)
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello)
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko)"
* tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
Documentation: ACPI: Align the SSDT overlays file with the code
PCI: VMD: ACPI: Make ACPI companion lookup work for VMD bus
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"A new feature called restricted DMA pools. It allows SWIOTLB to
utilize per-device (or per-platform) allocated memory pools instead of
using the global one.
The first big user of this is ARM Confidential Computing where the
memory for DMA operations can be set per platform"
* 'stable/for-linus-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: (23 commits)
swiotlb: use depends on for DMA_RESTRICTED_POOL
of: restricted dma: Don't fail device probe on rmem init failure
of: Move of_dma_set_restricted_buffer() into device.c
powerpc/svm: Don't issue ultracalls if !mem_encrypt_active()
s390/pv: fix the forcing of the swiotlb
swiotlb: Free tbl memory in swiotlb_exit()
swiotlb: Emit diagnostic in swiotlb_exit()
swiotlb: Convert io_default_tlb_mem to static allocation
of: Return success from of_dma_set_restricted_buffer() when !OF_ADDRESS
swiotlb: add overflow checks to swiotlb_bounce
swiotlb: fix implicit debugfs declarations
of: Add plumbing for restricted DMA pool
dt-bindings: of: Add restricted DMA pool
swiotlb: Add restricted DMA pool initialization
swiotlb: Add restricted DMA alloc/free support
swiotlb: Refactor swiotlb_tbl_unmap_single
swiotlb: Move alloc_size to swiotlb_find_slots
swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing
swiotlb: Update is_swiotlb_active to add a struct device argument
swiotlb: Update is_swiotlb_buffer to add a struct device argument
...
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching
to support future vendor provided vfio-pci variants (Yishai Hadas,
Max Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first
open, last close, and device sets (Jason Gunthorpe, Max Gurtovoy,
Yishai Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
-----BEGIN PGP SIGNATURE-----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=nzK7
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching to
support future vendor provided vfio-pci variants (Yishai Hadas, Max
Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first open,
last close, and device sets (Jason Gunthorpe, Max Gurtovoy, Yishai
Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
* tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio: (37 commits)
vfio/pci: Introduce vfio_pci_core.ko
vfio: Use kconfig if XX/endif blocks instead of repeating 'depends on'
vfio: Use select for eventfd
PCI / VFIO: Add 'override_only' support for VFIO PCI sub system
PCI: Add 'override_only' field to struct pci_device_id
vfio/pci: Move module parameters to vfio_pci.c
vfio/pci: Move igd initialization to vfio_pci.c
vfio/pci: Split the pci_driver code out of vfio_pci_core.c
vfio/pci: Include vfio header in vfio_pci_core.h
vfio/pci: Rename ops functions to fit core namings
vfio/pci: Rename vfio_pci_device to vfio_pci_core_device
vfio/pci: Rename vfio_pci_private.h to vfio_pci_core.h
vfio/pci: Rename vfio_pci.c to vfio_pci_core.c
vfio/ap_ops: Convert to use vfio_register_group_dev()
s390/vfio-ap: replace open coded locks for VFIO_GROUP_NOTIFY_SET_KVM notification
s390/vfio-ap: r/w lock for PQAP interception handler function pointer
vfio/type1: Fix vfio_find_dma_valid return
vfio-pci/zdev: Remove repeated verbose license text
vfio: platform: reset: Convert to SPDX identifier
vfio: Remove struct vfio_device_ops open/release
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYTB6pAAKCRCAXGG7T9hj
vk9xAP9hUQtGdTb5eW9+3X3PHDON2jGbydAMtQ57WJLdqj0oFgD/cGV95PKv0jgg
zgw6Icf9Vp6APF/Ucd/dOB0B6qviJgw=
=PNRc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- some small cleanups
- a fix for a bug when running as Xen PV guest which could result in
not all memory being transferred in case of a migration of the guest
- a small series for getting rid of code for supporting very old Xen
hypervisor versions nobody should be using since many years now
- a series for hardening the Xen block frontend driver
- a fix for Xen PV boot code issuing warning messages due to a stray
preempt_disable() on the non-boot processors
* tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: remove stray preempt_disable() from PV AP startup code
xen/pcifront: Removed unnecessary __ref annotation
x86: xen: platform-pci-unplug: use pr_err() and pr_warn() instead of raw printk()
drivers/xen/xenbus/xenbus_client.c: fix bugon.cocci warnings
xen/blkfront: don't trust the backend response data blindly
xen/blkfront: don't take local copy of a request from the ring page
xen/blkfront: read response from backend only once
xen: assume XENFEAT_gnttab_map_avail_bits being set for pv guests
xen: assume XENFEAT_mmu_pt_update_preserve_ad being set for pv guests
xen: check required Xen features
xen: fix setting of max_pfn in shared_info
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
- Fix runtime PM imbalance in rcar_pcie_ep_probe() (Dinghao Liu)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Add L1 link state fix into data abort hook
PCI: rcar: Fix runtime PM imbalance in rcar_pcie_ep_probe()
- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
- Add domain_nr in struct pci_host_bridge (Boqun Feng)
- Use host bridge MSI domain for root buses if present (Boqun Feng)
- Allow ARM64 virtual host bridge with no ACPI companion (e.g., Hyper-V)
(Boqun Feng)
- Make Hyper-V enumeration more generic (Arnd Bergmann)
- Set Hyper-V domain_nr at probe-time (Boqun Feng)
- Set up Hyper-V MSI domain at bridge probe-time (Boqun Feng)
- Enable Hyper-V bridge probing on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hyper-v:
PCI: hv: Turn on the host bridge probing on ARM64
PCI: hv: Set up MSI domain at bridge probing time
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
PCI: hv: Generify PCI probing
arm64: PCI: Support root bridge preparation for Hyper-V
arm64: PCI: Restructure pcibios_root_bridge_prepare()
PCI: Support populating MSI domains of root buses via bridges
PCI: Introduce domain_nr in pci_host_bridge
- Convert bool in structs to bitfield (Kishon Vijay Abraham I)
- Work around J7200 non-PCIe SERDES lane electrical issue that prevents
PCIe link training (Nadeem Athani)
- Add J7200 PCIe support to j721e (Kishon Vijay Abraham I)
- Add AM64 PCIe support to j721e (Kishon Vijay Abraham I)
- Add J7200 and AM64 device IDs to endpoint test (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
misc: pci_endpoint_test: Add deviceID for AM64 and J7200
PCI: j721e: Add PCIe support for AM64
PCI: j721e: Add PCIe support for J7200
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
- Fix PIO config access status checking (Evan Wang)
- Increase config access polling delay to 1.5s (Pali Rohár)
- Add PCIe Root Capabilities to bridge emulation (Pali Rohár)
- Report Config Request Retry Status when Software Visibility enabled (Pali
Rohár)
- Add back configuration of PCIe resources from 'ranges' DT property and
pay attention to DT size and CPU/PCI offset to fix issues with I/O port
space (Pali Rohár)
- Serialize masking and unmasking legacy INTx interrupts (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
PCI: aardvark: Fix reporting CRS value
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Increase polling delay to 1.5s while waiting for PIO response
PCI: aardvark: Fix checking for PIO status
- Cache PCIe Device Capabilities register (Amey Narkhede)
- Add pcie_reset_flr() with 'probe' argument (Amey Narkhede)
- Add pdev->reset_methods[] array to track reset method ordering (Amey
Narkhede)
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
- Enable Bandwidth Notification only if port supports it (Stuart Hayes)
* pci/portdrv:
PCI/portdrv: Enable Bandwidth Notification only if port supports it
ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.
Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().
[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some systems, in order to get to the deepest low-power state of
the platform (which may be necessary to save significant enough
amounts of energy while suspended to idle. for example), devices on
the PCI bus exposed by the VMD driver need to be power-managed via
ACPI. However, the layout of the ACPI namespace below the VMD
controller device object does not reflect the layout of the PCI bus
under the VMD host bridge, so in order to identify the ACPI companion
objects for the devices on that bus, it is necessary to use a special
_ADR encoding on the ACPI side. In other words, acpi_pci_find_companion()
does not work for these devices, so it needs to be amended with a
special lookup logic specific to the VMD bus.
Address this issue by allowing the VMD driver to temporarily install
an ACPI companion lookup hook containing the code matching the devices
on the VMD PCI bus with the corresponding objects in the ACPI
namespace.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
An unnecessary "__ref" annotation was removed from the
"drivers/pci/xen_pcifront.c" file. The function where the annotation
was used was "pcifront_backend_changed()", which does not call any
functions annotated as "__*init" nor "__*exit". This makes "__ref"
unnecessary since this annotation is used to make the compiler ignore
section miss-matches when they are not happening here in the first
place.
In addition to the aforementioned change, some code style issues were
fixed in the same file.
Signed-off-by: Sergio Miguéns Iglesias <sergio@lony.xyz>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210830175305.13370-1-sergio@lony.xyz
Signed-off-by: Juergen Gross <jgross@suse.com>
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read
out again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs
in kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by
the router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105)
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JDGD
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
After recent introduction of new VPD API functions and user migration
these defines and inline functions aren't used outside VPD core any
longer.
Link: https://lore.kernel.org/r/d33e06bf-bc5e-ece7-bf35-7245ae224d1b@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_vpd_find_id_string() API function to retrieve the ID string from
VPD.
This way callers don't need pci_vpd_lrdt_size() any longer, and it can be
made private to the VPD core.
Link: https://lore.kernel.org/r/c5225bf6-8d29-970d-e271-0d7b52252630@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_vpd_find_tag() post-processing from pci_vpd_find_ro_info_keyword()
to pci_vpd_find_tag(). This simplifies function pci_vpd_find_id_string()
that will be added in a subsequent patch.
Link: https://lore.kernel.org/r/fb15393f-d3b2-e140-2643-570d3abd7382@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/96ca2a56-383e-9b61-9cba-4f1e5611dc15@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/71131eca-0502-7878-365f-30b6614161cf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to
the intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni).
-----BEGIN PGP SIGNATURE-----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=sx6G
-----END PGP SIGNATURE-----
Merge tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These address some PCI device power management issues, add new
hardware support to the RAPL power capping driver, add HWP guaranteed
performance change notification support to the intel_pstate driver,
replace deprecated CPU-hotplug functions in a few places, update CPU
PM notifiers to use raw spinlocks, update the PM domains framework
(new DT property support, Kconfig fix), do a couple of cleanups in
code related to system sleep, and improve the energy model and the
schedutil cpufreq governor.
Specifics:
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to the
intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni)"
* tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: domains: Fix domain attach for CONFIG_PM_OPP=n
powercap: Add Power Limit4 support for Alder Lake SoC
cpufreq: intel_pstate: Process HWP Guaranteed change notification
thermal: intel: Allow processing of HWP interrupt
notifier: Remove atomic_notifier_call_chain_robust()
PM: cpu: Make notifier chain use a raw_spinlock_t
PM: sleep: unmark 'state' functions as kernel-doc
arm64: dts: sc7180: Add required-opps for i2c
PM: domains: Add support for 'required-opps' to set default perf state
opp: Don't print an error if required-opps is missing
cpufreq: schedutil: Use kobject release() method to free sugov_tunables
PM: EM: Increase energy calculation precision
PM: sleep: check RTC features instead of ops in suspend_test
PM: sleep: s2idle: Replace deprecated CPU-hotplug functions
cpufreq: Replace deprecated CPU-hotplug functions
powercap: intel_rapl: Replace deprecated CPU-hotplug functions
PCI: PM: Enable PME if it can be signaled from D3cold
PCI: PM: Avoid forcing PCI_D0 for wakeup reasons inconsistently
PCI: Use pci_update_current_state() in pci_enable_device_flags()
HiSilicon KunPeng920 and KunPeng930 have devices that appear as PCI but are
actually on the AMBA bus. These fake PCI devices can support SVA via the
SMMU stall feature.
DT systems can indicate this in the device tree, but ACPI systems don't
have that mechanism, so add a "dma-can-stall" property manually for them.
[bhelgaas: add text from Robin as comment near quirk]
Link: https://lore.kernel.org/r/1626144876-11352-4-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The switch statement in the artpec6_pcie_probe() has a local code block
where "val" is defined and immediately used by the artpec6_pcie_readl().
This extra code block adds brackets at the same indentation level as the
switch statement itself which can hinder readability of the code.
Move the "val" declaration to the top of the function and remove
the extra code block from the switch statement.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701204401.1636562-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add support for the PCIe RC controller on Toshiba Visconti ARM SoCs. This
PCIe controller is based on the Synopsys DesignWare PCIe core.
Link: https://lore.kernel.org/r/20210811083830.784065-3-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Previously we assumed that all Root Ports and Switch Downstream Ports
supported Link Bandwidth Notification. Per spec, this is only required
for Ports supporting Links wider than x1 and/or multiple Link speeds
(PCIe r5.0, sec 7.5.3.6).
Because we assumed all Ports supported it, we tried to set up a Bandwidth
Notification IRQ, which failed for devices that don't support IRQs at all,
which meant pcieport didn't attach to the Port at all.
Check the Link Bandwidth Notification Capability bit and enable the service
only when the Port supports it.
[bhelgaas: commit log]
Fixes: e8303bb7a7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/r/20210512213314.7778-1-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Core changes:
- The usual set of small fixes and improvements all over the place, but nothing
outstanding
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI interrupts
of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements
-----BEGIN PGP SIGNATURE-----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=qyll
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates to the interrupt core and driver subsystems:
Core changes:
- The usual set of small fixes and improvements all over the place,
but nothing stands out
MSI changes:
- Further consolidation of the PCI/MSI interrupt chip code
- Make MSI sysfs code independent of PCI/MSI and expose the MSI
interrupts of platform devices in the same way as PCI exposes them.
Driver changes:
- Support for ARM GICv3 EPPI partitions
- Treewide conversion to generic_handle_domain_irq() for all chained
interrupt controllers
- Conversion to bitmap_zalloc() throughout the irq chip drivers
- The usual set of small fixes and improvements"
* tag 'irq-core-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
platform-msi: Add ABI to show msi_irqs of platform devices
genirq/msi: Move MSI sysfs handling from PCI to MSI core
genirq/cpuhotplug: Demote debug printk to KERN_DEBUG
irqchip/qcom-pdc: Trim unused levels of the interrupt hierarchy
irqdomain: Export irq_domain_disconnect_hierarchy()
irqchip/gic-v3: Fix priority comparison when non-secure priorities are used
irqchip/apple-aic: Fix irq_disable from within irq handlers
pinctrl/rockchip: drop the gpio related codes
gpio/rockchip: drop irq_gc_lock/irq_gc_unlock for irq set type
gpio/rockchip: support next version gpio controller
gpio/rockchip: use struct rockchip_gpio_regs for gpio controller
gpio/rockchip: add driver for rockchip gpio
dt-bindings: gpio: change items restriction of clock for rockchip,gpio-bank
pinctrl/rockchip: add pinctrl device to gpio bank struct
pinctrl/rockchip: separate struct rockchip_pin_bank to a head file
pinctrl/rockchip: always enable clock for gpio controller
genirq: Fix kernel doc indentation
EDAC/altera: Convert to generic_handle_domain_irq()
powerpc: Bulk conversion to generic_handle_domain_irq()
nios2: Bulk conversion to generic_handle_domain_irq()
...
* pm-pci:
PCI: PM: Enable PME if it can be signaled from D3cold
PCI: PM: Avoid forcing PCI_D0 for wakeup reasons inconsistently
PCI: Use pci_update_current_state() in pci_enable_device_flags()
* pm-sleep:
PM: sleep: unmark 'state' functions as kernel-doc
PM: sleep: check RTC features instead of ops in suspend_test
PM: sleep: s2idle: Replace deprecated CPU-hotplug functions
* pm-domains:
PM: domains: Fix domain attach for CONFIG_PM_OPP=n
arm64: dts: sc7180: Add required-opps for i2c
PM: domains: Add support for 'required-opps' to set default perf state
opp: Don't print an error if required-opps is missing
* powercap:
powercap: Add Power Limit4 support for Alder Lake SoC
powercap: intel_rapl: Replace deprecated CPU-hotplug functions
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Some systems, e.g., HiSilicon KunPeng920 and KunPeng930, have devices that
appear as PCI but are actually on the AMBA bus. Some of these fake PCI
devices support a PASID-like feature and they do have a working PASID
capability even though they do not use the PCIe Transport Layer Protocol
and do not support TLP prefixes.
Add a pasid_no_tlp bit for this "PASID works without TLP prefixes" case and
update pci_enable_pasid() so it can enable PASID on these devices.
Set this bit for HiSilicon KunPeng920 and KunPeng930.
[bhelgaas: squashed, commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/1626144876-11352-2-git-send-email-zhangfei.gao@linaro.org
Link: https://lore.kernel.org/r/1626144876-11352-3-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add 'override_only' field to struct pci_device_id to be used as part of
pci_match_device().
When set, a driver only matches the entry when dev->driver_override is
set to that driver.
In addition, add a helper macro named 'PCI_DEVICE_DRIVER_OVERRIDE' to
enable setting some data on it.
Next patch from this series will use the above functionality.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-10-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Use of_get_pci_domain_nr() to get the pci domain.
If the "linux,pci-domain" property is present, we assume that the PCIe
bridge is an individual bridge, hence we only need to parse one port.
Link: https://lore.kernel.org/r/20210823032800.1660-5-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Use platform_get_irq_byname() to get the irq number
if the "interrupt-names" property is defined.
Link: https://lore.kernel.org/r/20210823032800.1660-4-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
For the new dts format, add a new method to get
shared pcie-cfg base address and use it to configure
the PCIECFG controller
Link: https://lore.kernel.org/r/20210823032800.1660-3-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
irq_mask and irq_unmask callbacks need to be properly guarded by raw spin
locks as masking/unmasking procedure needs atomic read-modify-write
operation on hardware register.
Link: https://lore.kernel.org/r/20210820155020.3000-1-pali@kernel.org
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Add a predicate that returns if PCIe PTM (Precision Time Measurement)
is enabled.
It will only return true if it's enabled in all the ports in the path
from the device to the root.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make pci_enable_ptm() accessible from the drivers.
Exposing this to the driver enables the driver to use the
'ptm_enabled' field of 'pci_dev' to check if PTM is enabled or not.
This reverts commit ac6c26da29 ("PCI: Make pci_enable_ptm() private").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move PCI's MSI sysfs code to the irq core so that other busses such as
platform can reuse it.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210813035628.6844-2-21cnbao@gmail.com
Now we have everything we need, just provide a proper sysdata type for
the bus to use on ARM64 and everything else works.
Link: https://lore.kernel.org/r/20210726180657.142727-9-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Since PCI_HYPERV depends on PCI_MSI_IRQ_DOMAIN which selects
GENERIC_MSI_IRQ_DOMAIN, we can use dev_set_msi_domain() to set up the
MSI domain at probing time, and this works for both x86 and ARM64.
Therefore use it as the preparation for ARM64 Hyper-V PCI support.
As a result, no longer need to maintain ->fwnode in x86 specific
pci_sysdata, and make hv_pcibus_device own it instead.
Link: https://lore.kernel.org/r/20210726180657.142727-8-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change, just store and maintain the PCI domain number in
the ->domain_nr of pci_host_bridge. Note that we still need to keep
the copy of domain number in x86-specific pci_sysdata, because x86 is
not a PCI_DOMAINS_GENERIC=y architecture, so the ->domain_nr of
pci_host_bridge doesn't work for it yet.
Link: https://lore.kernel.org/r/20210726180657.142727-7-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In order to support ARM64 Hyper-V PCI, we need to set up the bridge at
probing time because ARM64 is a PCI_DOMAIN_GENERIC=y arch and we don't
have pci_config_window (ARM64 sysdata) for a PCI root bus on Hyper-V, so
it's impossible to retrieve the information (e.g. PCI domains, MSI
domains) from bus sysdata on ARM64 after creation.
Originally in create_root_hv_pci_bus(), pci_create_root_bus() is used to
create the root bus and the corresponding bridge based on x86 sysdata.
Now we create a bridge first and then call pci_scan_root_bus_bridge(),
which allows us to do the necessary set-ups for the bridge.
Link: https://lore.kernel.org/r/20210726180657.142727-6-boqun.feng@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Currently, at probing time, the MSI domains of root buses are populated
if either the information of MSI domain is available from firmware (DT
or ACPI), or arch-specific sysdata is used to pass the fwnode of the MSI
domain. These two conditions don't cover all, e.g. Hyper-V virtual PCI
on ARM64, which doesn't have the MSI information in the firmware and
couldn't use arch-specific sysdata because running on an architecture
with PCI_DOMAINS_GENERIC=y.
To support populating MSI domains of the root buses at the probing when
neither of the above condition is true, the ->msi_domain of the
corresponding bridge device is used: in pci_host_bridge_msi_domain(),
which should return the MSI domain of the root bus, the ->msi_domain of
the corresponding bridge is fetched first as a potential value of the
MSI domain of the root bus.
In order to use the approach to populate MSI domains, the driver needs
to dev_set_msi_domain() on the bridge before calling
pci_register_host_bridge(), and makes sure GENERIC_MSI_IRQ_DOMAIN=y.
Another advantage of this new approach is providing an arch-independent
way to populate MSI domains, which allows sharing the driver code as
much as possible between architectures.
Originally-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210726180657.142727-3-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently we retrieve the PCI domain number of the host bridge from the
bus sysdata (or pci_config_window if PCI_DOMAINS_GENERIC=y). Actually
we have the information at PCI host bridge probing time, and it makes
sense that we store it into pci_host_bridge. One benefit of doing so is
the requirement for supporting PCI on Hyper-V for ARM64, because the
host bridge of Hyper-V doesn't have pci_config_window, whereas ARM64 is
a PCI_DOMAINS_GENERIC=y arch, so we cannot retrieve the PCI domain
number from pci_config_window on ARM64 Hyper-V guest.
As the preparation for ARM64 Hyper-V PCI support, we introduce the
domain_nr in pci_host_bridge and a sentinel value to allow drivers to
set domain numbers properly at probing time. Currently
CONFIG_PCI_DOMAINS_GENERIC=y archs are only users of this
newly-introduced field.
Link: https://lore.kernel.org/r/20210726180657.142727-2-boqun.feng@gmail.com
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Interfaces and structs for saving and restoring PCI Capability state were
declared in include/linux/pci.h, but aren't needed outside drivers/pci/.
Move these to drivers/pci/pci.h:
struct pci_cap_saved_data
struct pci_cap_saved_state
void pci_allocate_cap_save_buffers()
void pci_free_cap_save_buffers()
int pci_add_cap_save_buffer()
int pci_add_ext_cap_save_buffer()
struct pci_cap_saved_state *pci_find_saved_cap()
struct pci_cap_saved_state *pci_find_saved_ext_cap()
Link: https://lore.kernel.org/r/20210802221728.1469304-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
PCIe Address Translation Services (ATS) provides a mechanism for a device
to provide an on-device caching translation agent (device IOTLB). We
already have a means to disable support for this feature via the pci=noats
option. For untrusted and externally facing devices, we not only disable
ATS support for the device, but we use Access Control Services (ACS)
Transaction Blocking to actively prevent devices from sending TLPs with
non-default AT field values.
Extend pci=noats to also make use of PCI_ACS_TB so that not only is ATS
disabled at the device, but blocked at the downstream ports. This provides
a means to further lock-down ATS for cases such as device assignment, where
it may not be the hardware configuration of the device that makes it
untrusted, but the driver running on the device.
Link: https://lore.kernel.org/r/162404966325.2362347.12176138291577486015.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since 39850ed510 ("PCI/PTM: Save/restore Precision Time Measurement
Capability for suspend/resume"), devices that have PTM capability but
don't enable it see this message on calls to pci_save_state():
no suspend buffer for PTM
Drop the message, it's perfectly fine not to use a capability.
Fixes: 39850ed510 ("PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume")
Link: https://lore.kernel.org/r/20210811185955.3112534-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David E. Box <david.e.box@linux.intel.com>
VPD checksum information and checksum calculation are specified by PCIe
r5.0, sec 6.28.2.2. Therefore checksum handling can and should be moved
into the PCI VPD core.
Add pci_vpd_check_csum() to validate the VPD checksum.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/1643bd7a-088e-1028-c9b0-9d112cf48d63@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All users of pci_vpd_find_info_keyword() are interested in the VPD RO
section only. In addition all calls are followed by the same activities to
calculate start of tag data area and size of the data area.
Add pci_vpd_find_ro_info_keyword() that combines these functionalities.
pci_vpd_find_info_keyword() can be phased out once all users are converted.
[bhelgaas: split pci_vpd_check_csum() to separate patch]
Link: https://lore.kernel.org/r/1643bd7a-088e-1028-c9b0-9d112cf48d63@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several users of the VPD API use a fixed-size buffer and read the VPD into
it for further usage. This requires special handling for the case that the
buffer isn't big enough to hold the full VPD data. Also the buffer is
often allocated on the stack, which isn't too nice.
Add pci_vpd_alloc() to dynamically allocate buffer of the correct size and
read VPD into it.
Link: https://lore.kernel.org/r/955ff598-0021-8446-f856-0c2c077635d7@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In commit 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a ("PCI: aardvark: Remove PCIe outbound window configuration")
Not much to see here. Half the fixes this time are for Qualcomm dts files,
fixing small mistakes on certain machines. The other fixes are:
- A 5.13 regression fix for freescale QE interrupt controller\
- A fix for TI OMAP gpt12 timer error handling
- A randconfig build regression fix for ixp4xx
- Another defconfig fix following the CONFIG_FB dependency rework
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Ohvh
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Not much to see here. Half the fixes this time are for Qualcomm dts
files, fixing small mistakes on certain machines. The other fixes are:
- A 5.13 regression fix for freescale QE interrupt controller\
- A fix for TI OMAP gpt12 timer error handling
- A randconfig build regression fix for ixp4xx
- Another defconfig fix following the CONFIG_FB dependency rework"
* tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: fsl: qe: fix static checker warning
ARM: ixp4xx: fix building both pci drivers
ARM: configs: Update the nhk8815_defconfig
bus: ti-sysc: Fix error handling for sysc_check_active_timer()
soc: fsl: qe: convert QE interrupt controller to platform_device
arm64: dts: qcom: sdm845-oneplus: fix reserved-mem
arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem
arm64: dts: qcom: sc7280: Fixup cpufreq domain info for cpu7
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping
arm64: dts: qcom: msm8992-bullhead: Remove PSCI
arm64: dts: qcom: c630: fix correct powerdown pin for WSA881x
Two legacy PCI sysfs objects "legacy_io" and "legacy_mem" were updated
to use an unified address space in the commit 636b21b501 ("PCI: Revoke
mappings like devmem"). This allows for revocations to be managed from
a single place when drivers want to take over and mmap() a /dev/mem
range.
Following the update, both of the sysfs objects should leverage the
iomem_get_mapping() function to get an appropriate address range, but
only the "legacy_io" has been correctly updated - the second attribute
seems to be using a wrong variable to pass the iomem_get_mapping()
function to.
Thus, correct the variable name used so that the "legacy_mem" sysfs
object would also correctly call the iomem_get_mapping() function.
Fixes: 636b21b501 ("PCI: Revoke mappings like devmem")
Link: https://lore.kernel.org/r/20210812132144.791268-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com
Signed-off-by: Marcin Bachry <hegel666@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Prike Liang <prike.liang@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
AM64 has the same PCIe IP as in J7200 with certain erratas not
applicable (quirk_detect_quiet_flag). Add support for "ti,am64-pcie-host"
compatible and "ti,am64-pcie-ep" compatible that is specific to AM64.
Link: https://lore.kernel.org/r/20210811123336.31357-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
J7200 has the same PCIe IP as in J721E with minor changes in the
wrapper. J7200 allows byte access of bridge configuration space
registers and the register field for LINK_DOWN interrupt is different.
J7200 also requires "quirk_detect_quiet_flag" to be set. Configure these
changes as part of driver data applicable only to J7200.
Link: https://lore.kernel.org/r/20210811123336.31357-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe fails to link up if SERDES lanes not used by PCIe are assigned to
another protocol. For example, link training fails if lanes 2 and 3 are
assigned to another protocol while lanes 0 and 1 are used for PCIe to
form a two lane link. This failure is due to an incorrect tie-off on an
internal status signal indicating electrical idle.
Status signals going from SERDES to PCIe Controller are tied-off when a
lane is not assigned to PCIe. Signal indicating electrical idle is
incorrectly tied-off to a state that indicates non-idle. As a result,
PCIe sees unused lanes to be out of electrical idle and this causes
LTSSM to exit Detect.Quiet state without waiting for 12ms timeout to
occur. If a receiver is not detected on the first receiver detection
attempt in Detect.Active state, LTSSM goes back to Detect.Quiet and
again moves forward to Detect.Active state without waiting for 12ms as
required by PCIe base specification. Since wait time in Detect.Quiet is
skipped, multiple receiver detect operations are performed back-to-back
without allowing time for capacitance on the transmit lines to
discharge. This causes subsequent receiver detection to always fail even
if a receiver gets connected eventually.
Add a quirk flag "quirk_detect_quiet_flag" to program the minimum
time the LTSSM should wait on entering Detect.Quiet state here.
This has to be set for J7200 as it has an incorrect tie-off on unused
lanes.
Link: https://lore.kernel.org/r/20210811123336.31357-3-kishon@ti.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Now that support for SR-IOV is added in PCIe endpoint core, add support
to configure virtual functions in the Cadence PCIe EP driver.
Link: https://lore.kernel.org/r/20210819123343.1951-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
No functional change. Simplify code to get register base address for
configuring PCI BAR.
Link: https://lore.kernel.org/r/20210819123343.1951-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
While the physical function has to be linked to endpoint controller, the
virtual function has to be linked to a physical function. Add support to
link a physical function to a virtual function in pci-ep-cfs.
Link: https://lore.kernel.org/r/20210819123343.1951-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support to add virtual function in endpoint core. The virtual
function can only be associated with a physical function instead of a
endpoint controller. Provide APIs to associate a virtual function with
a physical function here.
[weiyongjun1@huawei.com: PCI: endpoint: Fix missing unlock on error in
pci_epf_add_vepf() - Reported-by: Hulk Robot <hulkci@huawei.com>]
Link: https://lore.kernel.org/r/20210819123343.1951-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Change the type of probe argument in functions which implement reset
methods from int to bool to make the context and intent clear.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-10-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
_RST is a standard ACPI method that performs a function level reset of a
device (ACPI v6.3, sec 7.3.25).
Add pci_dev_acpi_reset() to probe for _RST method and execute if present.
The default priority of this reset is set to below device-specific and
above hardware resets.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-9-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Previously, the ACPI_COMPANION() of a pci_dev was usually set by
acpi_bind_one() in this path:
pci_device_add
pci_configure_device
pci_init_capabilities
device_add
device_platform_notify
acpi_platform_notify
acpi_device_notify # KOBJ_ADD
acpi_bind_one
ACPI_COMPANION_SET
However, things like pci_configure_device() and pci_init_capabilities()
that run before device_add() need the ACPI_COMPANION, e.g.,
acpi_pci_bridge_d3() uses a _DSD method to learn about D3 support. These
places had special-case code to manually look up the ACPI_COMPANION.
Set the ACPI_COMPANION earlier, in pci_setup_device(), so it will be
available while configuring the device. This covers both paths to creating
pci_dev objects:
pci_scan_single_device # for normal non-SR-IOV devices
pci_scan_device
pci_setup_device
pci_set_acpi_fwnode
pci_device_add
pci_iov_add_virtfn # for SR-IOV virtual functions
pci_setup_device
pci_set_acpi_fwnode
Also move the OF fwnode setup to the same spot.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210817180500.1253-8-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Use acpi_pci_power_manageable() instead of duplicating the logic in
acpi_pci_bridge_d3(). No functional change intended.
[bhelgaas: split out from
https://lore.kernel.org/r/20210817180500.1253-8-ameynarkhede03@gmail.com]
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the existing logic from acpi_pci_bridge_d3() to a separate function
pci_set_acpi_fwnode() to set the ACPI fwnode. No functional change
intended.
Link: https://lore.kernel.org/r/20210817180500.1253-7-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add "reset_method" sysfs attribute to enable user to query and set
preferred device reset methods and their ordering.
[bhelgaas: on invalid sysfs input, return error and preserve previous
config, as in earlier patch versions]
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-6-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
"reset_fn" indicates whether the device supports any reset mechanism.
Remove the use of reset_fn in favor of the reset_methods array that tracks
supported reset mechanisms of a device and their ordering.
The octeon driver incorrectly used reset_fn to detect whether the device
supports FLR or not. Use pcie_reset_flr() to probe whether it supports FLR.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-5-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Add reset_methods[] in struct pci_dev to keep track of reset mechanisms
supported by the device and their ordering.
Refactor probing and reset functions to take advantage of calling
convention of reset functions.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-4-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Most reset methods are of the form "pci_*_reset(dev, probe)". pcie_flr()
was an exception because it relied on a separate pcie_has_flr() function
instead of taking a "probe" argument.
Add "pcie_reset_flr(dev, probe)" to follow the convention. Remove
pcie_has_flr().
Some pcie_flr() callers that did not use pcie_has_flr() remain.
[bhelgaas: commit log, rework pcie_reset_flr() to use dev->devcap directly]
Link: https://lore.kernel.org/r/20210817180500.1253-3-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Add a new member called devcap in struct pci_dev for caching the PCIe
Device Capabilities register to avoid reading PCI_EXP_DEVCAP multiple
times.
Refactor pcie_has_flr() to use cached device capabilities.
Link: https://lore.kernel.org/r/20210817180500.1253-2-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
When the link is in L1, hardware should return it to L0
automatically whenever a transaction targets a component on the
other end of the link (PCIe r5.0, sec 5.2).
The R-Car PCIe controller doesn't handle this transition correctly.
If the link is not in L0, an MMIO transaction targeting a downstream
device fails, and the controller reports an ARM imprecise external
abort.
Work around this by hooking the abort handler so the driver can
detect this situation and help the hardware complete the link state
transition.
When the R-Car controller receives a PM_ENTER_L1 DLLP from the
downstream component, it sets PMEL1RX bit in PMSR register, but then
the controller enters some sort of in-between state. A subsequent
MMIO transaction will fail, resulting in the external abort. The
abort handler detects this condition and completes the link state
transition by setting the L1IATN bit in PMCTLR and waiting for the
link state transition to complete.
Link: https://lore.kernel.org/r/20210815181650.132579-1-marek.vasut@gmail.com
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Hyper-V vPCI protocol version 1_4 adds support for create interrupt
v3. Create interrupt v3 essentially makes the size of the vector
field bigger in the message, thereby allowing bigger vector values.
For example, that will come into play for supporting LPI vectors
on ARM, which start at 8192.
Link: https://lore.kernel.org/r/MW4PR21MB20026A6EA554A0B9EC696AA8C0159@MW4PR21MB2002.namprd21.prod.outlook.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Enable PCIe reference clock. There is no remove function that's why
this should be enough for simple operation.
Normally this clock is enabled by default by firmware but there are
usecases where this clock should be enabled by driver itself.
It is also good that PCIe clock is recorded in a clock framework.
Link: https://lore.kernel.org/r/ee6997a08fab582b1c6de05f8be184f3fe8d5357.1624618100.git.michal.simek@xilinx.com
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
When both the old and the new PCI drivers are enabled
in the same kernel, there are a couple of namespace
conflicts that cause a build failure:
drivers/pci/controller/pci-ixp4xx.c:38: error: "IXP4XX_PCI_CSR" redefined [-Werror]
38 | #define IXP4XX_PCI_CSR 0x1c
|
In file included from arch/arm/mach-ixp4xx/include/mach/hardware.h:23,
from arch/arm/mach-ixp4xx/include/mach/io.h:15,
from arch/arm/include/asm/io.h:198,
from include/linux/io.h:13,
from drivers/pci/controller/pci-ixp4xx.c:20:
arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h:221: note: this is the location of the previous definition
221 | #define IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE_VIRT+(x)))
|
drivers/pci/controller/pci-ixp4xx.c:148:12: error: 'ixp4xx_pci_read' redeclared as different kind of symbol
148 | static int ixp4xx_pci_read(struct ixp4xx_pci *p, u32 addr, u32 cmd, u32 *data)
| ^~~~~~~~~~~~~~~
Rename both the ixp4xx_pci_read/ixp4xx_pci_write functions and the
IXP4XX_PCI_CSR macro. In each case, I went with the version that
has fewer callers to keep the change small.
Fixes: f7821b4934 ("PCI: ixp4xx: Add a new driver for IXP4xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: soc@kernel.org
Link: https://lore.kernel.org/r/20210721151546.2325937-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pci_dev_str_match_path() is often called with a spinlock held so the
allocation has to be atomic. The call tree is:
pci_specified_resource_alignment() <-- takes spin_lock();
pci_dev_str_match()
pci_dev_str_match_path()
Fixes: 45db33709c ("PCI: Allow specifying devices using a base bus and path of devfns")
Link: https://lore.kernel.org/r/20210812070004.GC31863@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Exporting sysfs files that can't be accessed doesn't make much sense.
Therefore, if either a quirk or the dynamic size calculation result in VPD
being marked as invalid, treat this as though the device has no VPD
capability. One consequence is that the "vpd" sysfs file is not visible.
Link: https://lore.kernel.org/r/6a02b204-4ed2-4553-c3b2-eacf9554fa8d@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Determine VPD size in pci_vpd_init().
Quirks set dev->vpd.len to a non-zero value, so they cause us to skip the
dynamic size calculation. Prerequisite is that we move the quirks from
FINAL to HEADER so they are run before pci_vpd_init().
Link: https://lore.kernel.org/r/cc4a6538-557a-294d-4f94-e6d1d3c91589@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that struct pci_vpd is really small, simplify the code by embedding
struct pci_vpd directly in struct pci_dev instead of dynamically allocating
it.
Link: https://lore.kernel.org/r/d898489e-22ba-71f1-2f31-f1a78dc15849@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of having a separate flag, use vp->len != 0 as indicator that VPD
validity has been checked. Now vpd->len == PCI_VPD_SZ_INVALID indicates
that VPD is invalid.
Link: https://lore.kernel.org/r/9f777bc7-5316-e1b8-e5d4-f9f609bdb5dd@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some multi-function devices share VPD hardware across functions and don't
work correctly for concurrent VPD accesses to different functions.
Struct pci_vpd_ops was added by 932c435cab ("PCI: Add dev_flags bit to
access VPD through function 0") so that on these devices, VPD accesses to
any function would always go to function 0.
It's easier to just check for the PCI_DEV_FLAGS_VPD_REF_F0 quirk bit in the
two places we need it than to deal with the struct pci_vpd_ops.
Simplify the code by removing struct pci_vpd_ops and removing the indirect
calls.
[bhelgaas: check for !func0_dev earlier, commit log]
Link: https://lore.kernel.org/r/b2532a41-df8b-860f-461f-d5c066c819d0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Switch the PCI/MSI core to use the new mask/unmask functions. No functional
change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.311207034@linutronix.de
The existing mask/unmask functions are convoluted and generate suboptimal
assembly code.
Provide a new set of functions which will be used in later patches to
replace the exisiting ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/875ywetozb.ffs@tglx
msi_mask() is calculating the possible mask bits for MSI per vector
masking.
Rename it to msi_multi_mask() and hand the MSI descriptor pointer into it
to simplify the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.203905260@linutronix.de
Handling of virtual MSI-X is obfuscated by letting pci_msix_desc_addr()
return NULL and checking the pointer.
Just use msi_desc::msi_attrib.is_virtual at the call sites and get rid of
that pointer check.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.151522318@linutronix.de
Three error exits doing exactly the same ask for a common error exit point.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.098828720@linutronix.de
msi_desc::masked is a misnomer. For MSI it's used to cache the MSI mask
bits when the device supports per vector masking. For MSI-X it's used to
cache the content of the vector control word which contains the mask bit
for the vector.
Replace it with a union of msi_mask and msix_ctrl to make the purpose clear
and fix up the usage sites.
No functional change
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729222543.045993608@linutronix.de
No point in looping over all entries when 64bit addressing mode is enabled
for nothing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210729222542.992849326@linutronix.de
The PCI core already ensures that the MSI[-X] state is correct when MSI[-X]
is disabled. For MSI the reset state is all entries unmasked and for MSI-X
all vectors are masked.
S390 masks all MSI entries and masks the already masked MSI-X entries
again. Remove it and let the device in the correct state.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20210729222542.939798136@linutronix.de
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acb ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
No point in using the raw write function from shutdown. Preparatory change
to introduce proper serialization for the msi_desc::masked cache.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.674391354@linutronix.de
The comments about preserving the cached state in pci_msi[x]_shutdown() are
misleading as the MSI descriptors are freed right after those functions
return. So there is nothing to restore. Preparatory change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.621609423@linutronix.de
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db0 ("PCI MSI: Unmask MSI if setup failed")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Reported-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de
When MSI-X is enabled the ordering of calls is:
msix_map_region();
msix_setup_entries();
pci_msi_setup_msi_irqs();
msix_program_entries();
This has a few interesting issues:
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e1 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e1 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de
The struct pci_vpd.flag member was used only to communicate between
pci_vpd_wait() and its callers. Remove the flag member and pass the value
directly to pci_vpd_wait() to simplify the code.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/e4ef6845-6b23-1646-28a0-d5c5a28347b6@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reading/writing 4 bytes should be fast enough even on a slow bus, therefore
pci_vpd_wait() doesn't have to be interruptible. Making it uninterruptible
allows to simplify the code.
In addition make VPD writes uninterruptible in general. It's about vital
data, and allowing writes to be interruptible may leave the VPD in an
inconsistent state.
Link: https://lore.kernel.org/r/258bf994-bc2a-2907-9181-2c7a562986d5@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vpd->len is initialized to PCI_VPD_MAX_SIZE, and if a quirk is used to set
a specific VPD size, then pci_vpd_set_size() sets vpd->valid, resulting in
pci_vpd_size() not being called. Therefore we can remove the old_size
argument. Note that we don't have to check off < PCI_VPD_MAX_SIZE because
that's implicitly done by pci_read_vpd().
Link: https://lore.kernel.org/r/ede36c16-5335-6867-43a1-293641348430@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, if we found any error in the VPD, we returned size 0, which
prevents access to all of VPD. But there may be valid resources in VPD
before the error, and there's no reason to prevent access to those.
"off" covers only VPD resources known to have valid header tags. In case
of error, return "off" (which may be zero if we haven't found any valid
header tags at all).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
VPD consists of a series of Small and Large Resources. Computing the size
of VPD requires only the length of each, which is specified in the generic
tag of each resource. We only expect to see ID_STRING, RO_DATA, and
RW_DATA in VPD, but it's not a problem if it contains other resource types
because all we care about is the size.
Drop the validity checking of Large Resource items.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
VPD is limited in size by the 15-bit VPD Address field in the VPD
Capability. Each resource tag includes a length that determines the
overall size of the resource. Reject any resources that would extend past
the maximum VPD size.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tag for toerh trees/branches to pull from in order to have a stable base
to build off of for the "Allow deferred execution of
iomem_get_mapping()" set of sysfs changes
Link: https://lore.kernel.org/r/20210729233235.1508920-1-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYQ0XAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymPsQCeLzeQco/wi96/nf2fhKqpAPsBtH4AoLqE8R7F
PDJCjDCLsbwL+7ZC2udo
=Fbxh
-----END PGP SIGNATURE-----
Merge tag 'sysfs_defferred_iomem_get_mapping-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core driver-core-next
sysfs: Allow deferred execution of iomem_get_mapping()
Tag for toerh trees/branches to pull from in order to have a stable base
to build off of for the "Allow deferred execution of
iomem_get_mapping()" set of sysfs changes
Link: https://lore.kernel.org/r/20210729233235.1508920-1-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'sysfs_defferred_iomem_get_mapping-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072402.15069-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are two users of iomem_get_mapping(), the struct file and struct
bin_attribute. The former has a member called "f_mapping" and the
latter has a member called "mapping", and both are poniters to struct
address_space.
Rename struct bin_attribute member to "f_mapping" to keep both meaning
and the usage consistent with other users of iomem_get_mapping().
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20210729233235.1508920-3-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer invocation of the iomem_get_mapping() to the sysfs open callback
so that it can be executed as needed when the binary sysfs object has
been accessed.
To do that, convert the "mapping" member of the struct bin_attribute
from a pointer to the struct address_space into a function pointer with
a signature that requires the same return type, and then updates the
sysfs_kf_bin_open() to invoke provided function should the function
pointer be valid.
Also, convert every invocation of iomem_get_mapping() into a function
pointer assignment, therefore allowing for the iomem_get_mapping()
invocation to be deferred to when the sysfs open callback runs.
Thus, this change removes the need for the fs_initcalls to complete
before any other sub-system that uses the iomem_get_mapping() would be
able to invoke it safely without leading to a failure and an Oops
related to an invalid iomem_get_mapping() access.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20210729233235.1508920-2-kw@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource() internally calls __devm_ioremap_resource() which
is where error checking and handling is actually taking place. i
Therefore, the dev_err() call in xgene_msi_probe() is redundant.
Remove it.
Link: https://lore.kernel.org/r/20210408132751.1198171-1-yangerkun@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ErKun Yang <yangerkun@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Don't populate the array err_msg on the stack but instead make it
static. Makes the object code smaller by 64 bytes.
While at it, add a missing const, as reported by checkpatch.
Compiled with gcc 11.0.1
Before:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25623 2844 32 28499 6f53 drivers/pci/controller/pci-tegra.o
After:
$ size drivers/pci/controller/pci-tegra.o
text data bss dec hex filename
25559 2844 32 28435 6f13 drivers/pci/controller/pci-tegra.o
Link: https://lore.kernel.org/r/5f3f35296b944b94546cc7d1e9cc6186484620d8.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Commit 9e38e690ac ("PCI: tegra: Fix OF node reference leak") has fixed
some node reference leaks in this function but missed some of them.
In fact, having 'port' referenced in the 'rp' structure is not enough to
prevent the leak, until 'rp' is actually added in the 'pcie->ports' list.
Add the missing 'goto err_node_put' accordingly.
Link: https://lore.kernel.org/r/55b11e9a7fa2987fbc0869d68ae59888954d65e2.1620148539.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Set CRSVIS flag in emulated root PCI bridge to indicate support for
Completion Retry Status.
Add check for CRSSVE flag from root PCI brige when issuing Configuration
Read Request via PIO to correctly returns fabricated CRS value as it is
required by PCIe spec.
Link: https://lore.kernel.org/r/20210722144041.12661-5-pali@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # e0d9d30b73 ("PCI: pci-bridge-emul: Fix big-endian support")
The 16-bit Root Capabilities register is at offset 0x1e in the PCIe
Capability. Rename current 'rsvd' struct member to 'rootcap'.
Link: https://lore.kernel.org/r/20210722144041.12661-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Measurements in different conditions showed that aardvark hardware PIO
response can take up to 1.44s. Increase wait timeout from 1ms to 1.5s to
ensure that we do not miss responses from hardware. After 1.44s hardware
returns errors (e.g. Completer abort).
The previous two patches fixed checking for PIO status, so now we can use
it to also catch errors which are reported by hardware after 1.44s.
After applying this patch, kernel can detect and print PIO errors to dmesg:
[ 6.879999] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100004
[ 6.896436] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
[ 6.913049] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100010
[ 6.929663] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100010
[ 6.953558] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100014
[ 6.970170] advk-pcie d0070000.pcie: Non-posted PIO Response Status: CA, 0xe00 @ 0x100014
[ 6.994328] advk-pcie d0070000.pcie: Posted PIO Response Status: COMP_ERR, 0x804 @ 0x100004
Without this patch kernel prints only a generic error to dmesg:
[ 5.246847] advk-pcie d0070000.pcie: config read/write timed out
Link: https://lore.kernel.org/r/20210722144041.12661-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da81 ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
There is an issue that when PCIe switch is connected to an Armada 3700
board, there will be lots of warnings about PIO errors when reading the
config space. According to Aardvark PIO read and write sequence in HW
specification, the current way to check PIO status has the following
issues:
1) For PIO read operation, it reports the error message, which should be
avoided according to HW specification.
2) For PIO read and write operations, it only checks PIO operation complete
status, which is not enough, and error status should also be checked.
This patch aligns the code with Aardvark PIO read and write sequence in HW
specification on PIO status check and fix the warnings when reading config
space.
[pali: Fix CRS handling when CRSSVE is not enabled]
Link: https://lore.kernel.org/r/20210722144041.12661-2-pali@kernel.org
Tested-by: Victor Gu <xigu@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # b1bd571447 ("PCI: aardvark: Indicate error in 'val' when config read fails")
PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().
[Note that if the device does not end up in D3cold and it cannot
signal PME from the original target power state, it will not signal
PME, so in that case the behavior does not change.]
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e8 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It is inconsistent to return PCI_D0 from pci_target_state() instead
of the original target state if 'wakeup' is true and the device
cannot signal PME from D0.
This only happens when the device cannot signal PME from the original
target state and any shallower power states (including D0) and that
case is effectively equivalent to the one in which PME singaling is
not supported at all. Since the original target state is returned in
the latter case, make the function do that in the former one too.
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 666ff6f83e ("PCI/PM: Avoid using device_may_wakeup() for runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In commit 7ef1c871da ("PCI: iproc: Use
pci_parse_request_of_pci_ranges()"), calling
devm_request_pci_bus_resources() was dropped from the common iProc
probe code, but is still needed for BCMA bus probing. Without it, there
will be lots of warnings like this:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x00c00000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00c00000]
Add back calling devm_request_pci_bus_resources() and adding the
resources to pci_host_bridge.windows for BCMA bus probe.
Link: https://lore.kernel.org/r/20210803215656.3803204-2-robh@kernel.org
Fixes: 7ef1c871da ("PCI: iproc: Use pci_parse_request_of_pci_ranges()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 669cbc7081 ("PCI: Move DT resource setup into
devm_pci_alloc_host_bridge()") made devm_pci_alloc_host_bridge() fail on
any DT resource parsing errors, but Broadcom iProc uses
devm_pci_alloc_host_bridge() on BCMA bus devices that don't have DT
resources. In particular, there is no 'ranges' property. Fix iProc by
making 'ranges' optional.
If 'ranges' is required by a platform, there's going to be more errors
latter on if it is missing.
Link: https://lore.kernel.org/r/20210803215656.3803204-1-robh@kernel.org
Fixes: 669cbc7081 ("PCI: Move DT resource setup into devm_pci_alloc_host_bridge()")
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roman Bacik <roman.bacik@broadcom.com>
Cc: Bharat Gooty <bharat.gooty@broadcom.com>
Cc: Abhishek Shah <abhishek.shah@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: Ray Jui <ray.jui@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: BCM Kernel Feedback <bcm-kernel-feedback-list@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Change pciconfig_read() syscall "err" return value from long to int. This
makes it consistent with pciconfig_write().
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210729233755.1509616-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.
If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.
When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno. But after
e4585da22a ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.
Userspace may rely on the ~0 data to detect errors, but after e4585da22a,
that would not detect CAP_SYS_ADMIN errors.
Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.
[bhelgaas: commit log, fold in Nathan's fix
https://lore.kernel.org/r/20210803200836.500658-1-nathan@kernel.org]
Fixes: e4585da22a ("pci syscall.c: Switch to refcounting API")
Link: https://lore.kernel.org/r/20210729233755.1509616-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Link: https://lore.kernel.org/r/20210802162630.2219813-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
