Add driver for Qualcomm PCIe Endpoint controller based on the DesignWare
core with added Qualcomm-specific wrapper around the core. The driver
support is very basic such that it supports only enumeration, PCIe
read/write, and MSI. There is no ASPM and PM support for now but these will
be added later.
The driver is capable of using the PERST# and WAKE# side-band GPIOs for
operation and written on top of the DWC PCI framework.
[bhelgaas: wrap a few long lines]
Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: restructured the driver and fixed several bugs for upstream]
Link: https://lore.kernel.org/r/20210920065946.15090-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Clean up the users of PCIE_DW_EP and introduce idiom
depends on PCI_ENDPOINT
select PCIE_DW_EP
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Furthermore, there is no need to repeat menu dependencies (PCI).
Clean up the users of PCIE_DW_HOST and introduce idiom
depends on PCI_MSI_IRQ_DOMAIN
select PCIE_DW_HOST
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.
Code refactoring completed in the commit 39bc500650 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".
Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.
Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
If the clock is provided externally we need to make sure it is enabled
before starting PCI scan.
Link: https://lore.kernel.org/r/20210531085934.2662457-5-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Unused since commit e259c2926c ("PCI: pci-dra7xx: Prepare for deferred
probe with module_platform_driver").
Link: https://lore.kernel.org/r/20210531085934.2662457-4-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable building the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20210531085934.2662457-3-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The switch statement in the artpec6_pcie_probe() has a local code block
where "val" is defined and immediately used by the artpec6_pcie_readl().
This extra code block adds brackets at the same indentation level as the
switch statement itself which can hinder readability of the code.
Move the "val" declaration to the top of the function and remove
the extra code block from the switch statement.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701204401.1636562-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add support for the PCIe RC controller on Toshiba Visconti ARM SoCs. This
PCIe controller is based on the Synopsys DesignWare PCIe core.
Link: https://lore.kernel.org/r/20210811083830.784065-3-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Link: https://lore.kernel.org/r/20210802162630.2219813-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The i.MX8MQ PCIe PHY needs 1.8V in default but can be supplied by either a
1.8V or a 3.3V regulator.
The "vph-supply" DT property tells us which external regulator supplies the
PHY. If that regulator supplies anything over 3V, enable the PHY's internal
3.3V-to-1.8V regulator.
Link: https://lore.kernel.org/r/1622771269-13844-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers beyond
that point that otherwise would lead to an abort on the i.MX 6QuadPlus.
See commit 075af61c19 ("PCI: imx6: Limit DBI register length") that
resolves a similar issue on the i.MX 6Quad PCIe.
Link: https://lore.kernel.org/r/1613789388-2495-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
When devm_ioremap_resource() fails, __devm_ioremap_resource() prints an
error message including the device name, failure cause, and possibly
resource information.
Remove the error message from imx6_pcie_probe() since it's redundant.
Link: https://lore.kernel.org/r/20210511114547.5601-1-thunder.leizhen@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:
- 7f10074474 removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
pcie-tegra.c can no longer be built as a module. Restore that rule.
- 7f10074474 added "#ifdef CONFIG_PCIE_TEGRA194" around the native
driver, but that's only set when the driver is built-in (for a module,
CONFIG_PCIE_TEGRA194_MODULE is defined).
The ACPI quirk is completely independent of the rest of the native
driver, so move the quirk to its own file and remove the #ifdef in the
native driver.
- 7f10074474 added symbols that are always defined but used only when
CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:
drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]
Fixes: 7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
Link: https://lore.kernel.org/r/20210610064134.336781-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
- Use generic config accessors for TI AM65x (K3) to fix regression (Kishon
Vijay Abraham I)
- Move MSI Receiver init to dw_pcie_host_init() so it is re-initialized
along with the RC in resume (Jisheng Zhang)
- Remove unused pcie_app_rd() (Jiapeng Chong)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Move iATU detection earlier
PCI: dwc/intel-gw: Remove unused function
PCI: dwc: Move dw_pcie_msi_init() to dw_pcie_setup_rc()
PCI: keystone: Let AM65 use the pci_ops defined in pcie-designware-host.c
Add driver for the SiFive FU740 PCIe host controller.
This controller is based on the DesignWare PCIe core.
Co-developed-by: Henry Styles <hes@sifive.com>
Co-developed-by: Erik Danie <erik.danie@sifive.com>
Co-developed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20210504105940.100004-6-greentime.hu@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Henry Styles <hes@sifive.com>
Signed-off-by: Erik Danie <erik.danie@sifive.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
If the host which makes use of IP's integrated MSI Receiver losts
power during suspend, we need to reinit the RC and MSI Receiver in
resume. But after we move dw_pcie_msi_init() into the core, we have no
API to do so. Usually the dwc users need to call dw_pcie_setup_rc() to
reinit the RC, we can solve this problem by moving dw_pcie_msi_init()
to dw_pcie_setup_rc().
Link: https://lore.kernel.org/r/20210325152604.6e79deba@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The PCIe controller in Tegra194 SoC is not ECAM-compliant. With the
current hardware design, ECAM can be enabled only for one controller (the
C5 controller) with bus numbers starting from 160 instead of 0. A different
approach is taken to avoid this abnormal way of enabling ECAM for just one
controller but to enable configuration space access for all the other
controllers. In this approach, ops are added through MCFG quirk mechanism
which access the configuration spaces by dynamically programming iATU
(internal AddressTranslation Unit) to generate respective configuration
accesses just like the way it is done in DesignWare core sub-system.
This issue is specific to Tegra194 and it would be fixed in the future
generations of Tegra SoCs.
Link: https://lore.kernel.org/r/20210416134537.19474-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
In config PCIE_TEGRA194_EP the mode incorrectly is referred to as
host mode. Fix it.
Link: https://lore.kernel.org/r/20201231032539.22322-1-wesley.sheng@amd.com
Signed-off-by: Wesley Sheng <wesley.sheng@amd.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
The only usage of them is to assign their address to the 'ops' field in
the pcie_port and the dw_pcie_ep structs, both which are pointers to
const. Make them const to allow the compiler to put them in read-only
memory.
Link: https://lore.kernel.org/r/20210207221604.48910-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
There are harmless warnings when compile testing the kernel with
CONFIG_TRIM_UNUSED_KSYMS:
drivers/pci/controller/dwc/pcie-al.o: no symbols
drivers/pci/controller/pci-thunder-ecam.o: no symbols
drivers/pci/controller/pci-thunder-pem.o: no symbols
The problem here is that the host drivers get built even when the
configuration symbols are all disabled, as they pretend to not be drivers
but are silently enabled because of the promise that ACPI-based systems
need no drivers.
Add back the normal symbols to have these drivers built, and change the
logic to otherwise only build them when both CONFIG_PCI_QUIRKS and
CONFIG_ACPI are enabled.
As a side-effect, this enables compile-testing the drivers on other
architectures, which in turn needs the acpi_get_rc_resources() function to
be defined.
Link: https://lore.kernel.org/r/20210308152501.2135937-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing this driver without ECAM support results in a link failure:
ld.lld: error: undefined symbol: pci_ecam_map_bus
>>> referenced by pcie-al.c
>>> pci/controller/dwc/pcie-al.o:(al_pcie_map_bus) in archive drivers/built-in.a
Select CONFIG_ECAM like the other drivers do.
Link: https://lore.kernel.org/r/20210308152501.2135937-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
After updating pci-dra7xx driver to probe with ti-sysc and genpd, I
noticed that dra7xx_pcie_probe() would not run if a power-domains property
was configured for the interconnect target module.
Turns out that module_platform_driver_probe uses platform_driver_probe(),
while builtin_platform_driver uses platform_driver_register().
Only platform_driver_register() works for deferred probe as noted in the
comments for __platform_driver_probe() in drivers/base/platform.c with a
line saying "Note that this is incompatible with deferred probing".
With module_platform_driver_probe, we have platform_driver_probe() produce
-ENODEV error at device_initcall() level, and no further attempts are done.
Let's fix this by using module_platform_driver instead.
Note this is not an issue currently as we probe devices with simple-bus,
and only is needed as we start probing the device with ti-sysc, or when
probed with simple-pm-bus.
Note that we must now also remove __init for probe related functions to
avoid a section mismatch warning.
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Remove IRQ handler & data together for altera, brcmstb, dwc (Martin
Kaiser)
- Fix xgene race in installing chained IRQ handler (Martin Kaiser)
- Drop PCIE_RCAR config option (replaced by PCIE_RCAR_HOST) (Lad Prabhakar)
- Fix xgene comment about CRS vs CRS SV (Bjorn Helgaas)
* remotes/lorenzo/pci/misc:
PCI: hv: Fix typo
PCI: xgene: Fix CRS SV comment
PCI: brcmstb: Remove chained IRQ handler and data in one go
PCI: Drop PCIE_RCAR config option
PCI: xgene-msi: Fix race in installing chained irq handler
PCI: dwc: Remove IRQ handler and data in one go
PCI: altera-msi: Remove IRQ handler and data in one go
- Add support for SM8250 PCIe SF TBU clock (Dmitry Baryshkov)
- Use PHY_REFCLK_USE_PAD only for qcom ipq8064 (Ansuel Smith)
* pci/qcom:
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
The use of PHY_REFCLK_USE_PAD introduced a regression for apq8064 devices.
It was tested that while apq doesn't require the padding, ipq SoC must use
it or the kernel hangs on boot.
Link: https://lore.kernel.org/r/20201019165555.8269-1-ansuelsmth@gmail.com
Fixes: de3c4bf648 ("PCI: qcom: Add support for tx term offset for rev 2.1.0")
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.19+
We have removed the assumption that dw_pcie_ops always exists in the dwc
core driver, so we can remove the useless dw_pcie_ops now.
Link: https://lore.kernel.org/r/20210128144324.2fa8577c@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Chocron <jonnyc@amazon.com>
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The size parameter is unsigned long type which can accept size > 4GB. In
that case, the upper limit address must be programmed. Add support to
program the upper limit address and set INCREASE_REGION_SIZE in case size >
4GB.
Link: https://lore.kernel.org/r/1612250918-19610-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since outbound iATU permits size to be greater than 4GB for which the
support is also available, allow EP function to send u64 size instead of
truncating to u32.
Link: https://lore.kernel.org/r/1609929900-19082-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Since commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and
"addr_space" resource setup into common code"), the code
setting dbi_base when the config space is defined in 'ranges' property
instead of 'reg' is dead code as dbi_base is never NULL.
Rather than fix this, let's just drop the code. Using ranges has been
deprecated since 2014. The only platforms using this were exynos5440,
i.MX6 and Spear13xx. Exynos5440 is dead and has been removed. i.MX6 and
Spear13xx had PCIe support added just before this was deprecated and
were fixed within a kernel release or 2.
Link: https://lore.kernel.org/r/20201215194149.86831-1-robh@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fw_devlink will defer the probe until all suppliers are ready. We can't
use builtin_platform_driver_probe() because it doesn't retry after probe
deferral. Convert it to builtin_platform_driver().
Link: https://lore.kernel.org/r/20210120105246.23218-1-michael@walle.cc
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The LX2160A rev2 uses the same PCIe IP as LS2088A, but LX2160A rev2 PCIe
controller is integrated with different stride between PFs' register
address.
Link: https://lore.kernel.org/r/20201026051448.1913-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DesignWare core has a TLP digest (TD) override bit in one of the control
registers of ATU. This bit also needs to be programmed for proper ECRC
functionality. This is currently identified as an issue with DesignWare
IP version 4.90a.
[bhelgaas: fix typos/grammar errors]
Link: https://lore.kernel.org/r/20201230165723.673-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
- Support multiple ATU memory regions (Rob Herring)
- Warn if non-prefetchable memory aperture is > 32-bit (Vidya Sagar)
- Allow programming ATU for >4GB memory (Vidya Sagar)
- Move ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup to common code (Rob
Herring)
- Remove unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset to reduce dependencies on
bootloader (Rob Herring)
- Use the default MSI irq_chip for dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework and simplify DWC MSI initialization (Rob Herring)
- Move link handling to DWC common code (Rob Herring)
- Move dw_pcie_msi_init() calls to DWC common code (Rob Herring)
- Move dw_pcie_setup_rc() calls to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob Herring)
- Revert "keystone: Drop duplicated 'num-viewport'" to prepare for
detecting number of iATU regions without help from DT (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of DWC iATU windows from device registers (Rob Herring)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add samsung,exynos-pcie and samsung,exynos-pcie-phy bindings for
Exynos5433 variant (Marek Szyprowski)
- Rework phy-exynos-pcie driver to support Exynos5433 PCIe PHY (Jaehoon
Chung)
- Rework pci-exynos.c to support Exynos5433 PCIe host (Jaehoon Chung)
- Move tegra "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read tegra dbi" base address in application logic (Vidya Sagar)
- Fix tegra ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set Tegra194 DesignWare IP version to 0x490A (Vidya Sagar)
- Continue tegra unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable tegra LTSSM during L2 entry (Vidya Sagar)
- Add SM8250 SoC PCIe DT bindings and support (Manivannan Sadhasivam)
- Add SM8250 BDF to SID mapping (Manivannan Sadhasivam)
- Set 32-bit DMA mask for DWC MSI target address allocation (Vidya Sagar)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: qcom: Add SM8250 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
PCI: tegra: Disable LTSSM during L2 entry
PCI: tegra: Check return value of tegra_pcie_init_controller()
PCI: tegra: Continue unconfig sequence even if parts fail
PCI: tegra: Set DesignWare IP version
PCI: tegra: Fix ASPM-L1SS advertisement disable code
PCI: tegra: Read "dbi" base address to program in application logic
PCI: tegra: Move "dbi" accesses to post common DWC initialization
PCI: dwc: exynos: Rework the driver to support Exynos5433 variant
phy: samsung: phy-exynos-pcie: rework driver to support Exynos5433 PCIe PHY
dt-bindings: phy: exynos: add the samsung,exynos-pcie-phy binding
dt-bindings: PCI: exynos: add the samsung,exynos-pcie binding
dt-bindings: PCI: exynos: drop samsung,exynos5440-pcie binding
PCI: dwc: Detect number of iATU windows
PCI: dwc: Move inbound and outbound windows to common struct
Revert "PCI: dwc/keystone: Drop duplicated 'num-viewport'"
PCI: dwc: Remove unnecessary wrappers around dw_pcie_host_init()
PCI: dwc: Move dw_pcie_setup_rc() to DWC common code
PCI: dwc: Move dw_pcie_msi_init() into core
PCI: dwc: Move link handling into common code
PCI: dwc: Rework MSI initialization
PCI: dwc: Move MSI interrupt setup into DWC common code
PCI: dwc: Drop the .set_num_vectors() host op
PCI: dwc/dra7xx: Use the common MSI irq_chip
PCI: dwc: Ensure all outbound ATU windows are reset
PCI: dwc/intel-gw: Remove some unneeded function wrappers
PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code
PCI: dwc/intel-gw: Move ATU offset out of driver match data
PCI: dwc: Add support to program ATU for >4GB memory
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Support multiple ATU memory regions
Add ECAM-related constants to provide a set of standard constants
defining memory address shift values to the byte-level address that can
be used to access the PCI Express Configuration Space, and then move
native PCI Express controller drivers to use the newly introduced
definitions retiring driver-specific ones.
Refactor pci_ecam_map_bus() function to use newly added constants so
that limits to the bus, device function and offset (now limited to 4K as
per the specification) are in place to prevent the defective or
malicious caller from supplying incorrect configuration offset and thus
targeting the wrong device when accessing extended configuration space.
This refactor also allows for the ".bus_shift" initialisers to be
dropped when the user is not using a custom value as a default value
will be used as per the PCI Express Specification.
Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>,
and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create()
issue with .bus_shift and to Vladimir for proposing the fix.
[bhelgaas: incorporate Vladimir's fix, update commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Set DMA mask to 32-bit while allocating the MSI target address so that
the address is usable for both 32-bit and 64-bit MSI capable devices.
Throw a warning if it fails to set the mask to 32-bit to alert that
devices that are only 32-bit MSI capable may not work properly.
Link: https://lore.kernel.org/r/20201117165312.25847-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
For SM8250, we need to write the BDF to SID mapping in PCIe controller
register space for proper working. This is accomplished by extracting
the BDF and SID values from "iommu-map" property in DT and writing those
in the register address calculated from the hash value of BDF. In case
of collisions, the index of the next entry will also be written.
For the sake of it, let's introduce a "config_sid" callback and do it
conditionally for SM8250.
Link: https://lore.kernel.org/r/20201208121402.178011-4-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
SDM845. Hence the support is added reusing the members of ops_2_7_0.
The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
callback, which will be added in successive commit.
Link: https://lore.kernel.org/r/20201208121402.178011-3-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PCIe cards like Marvell SATA controller and some of the Samsung NVMe
drives don't support taking the link to L2 state. When the link doesn't
go to L2 state, Tegra194 requires the LTSSM to be disabled to allow PHY
to start the next link up process cleanly during suspend/resume sequence.
Failing to disable LTSSM results in the PCIe link not coming up in the
next resume cycle.
Link: https://lore.kernel.org/r/20201203133451.17716-6-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The return value of tegra_pcie_init_controller() must be checked before
PCIe link up check and registering debugfs entries subsequently as it
doesn't make sense to do these when the controller initialization itself
has failed.
Link: https://lore.kernel.org/r/20201203133451.17716-5-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the driver checks for error value of different APIs during the
uninitialization sequence. It just returns from there if there is any error
observed for one of those calls. Comparatively it is better to continue the
uninitialization sequence irrespective of whether some of them are
returning error. That way, it is more closer to complete uninitialization.
Link: https://lore.kernel.org/r/20201203133451.17716-4-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Set the DesignWare IP version for Tegra194 to 0x490A. This would be used
by the DesigWare sub-system to do any version specific configuration
(Ex:- TD bit programming for ECRC).
Link: https://lore.kernel.org/r/20201203133451.17716-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If the absence of CLKREQ# signal is indicated by the absence of
"supports-clkreq" in the device-tree node, current driver is disabling
the advertisement of ASPM-L1 Sub-States *before* the ASPM-L1 Sub-States
offset is correctly initialized. Since default value of the ASPM-L1SS
offset is zero, this is causing the Vendor-ID wrongly programmed to 0x10d2
instead of Nvidia's 0x10de thereby the quirks applicable for Tegra194 are
not being applied. This patch fixes this issue by refactoring the
code that disables the ASPM-L1SS advertisement.
Link: https://lore.kernel.org/r/20201203133451.17716-2-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controller in Tegra194 requires the "dbi" region base address to be
programmed in one of the application logic registers to enable CPU access
to the "dbi" region. But, commit a0fd361db8 ("PCI: dwc: Move "dbi",
"dbi2", and "addr_space" resource setup into common code") moved the code
that reads the whereabouts of "dbi" region to the common code causing the
existing code in pcie-tegra194.c file to program NULL in the application
logic registers. This is causing null pointer dereference when the "dbi"
registers are accessed. This issue is fixed by explicitly reading the
"dbi" base address from DT node.
Link: https://lore.kernel.org/r/20201125192554.5401-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space"
resource setup into common code") moved the code that sets up dbi_base
to DWC common code thereby creating a requirement to not access the "dbi"
region before calling common DWC initialization code. But, Tegra194
already had some code that programs some of the "dbi" registers resulting
in system crash. This patch addresses that issue by refactoring the code
to have accesses to the "dbi" region only after common DWC initialization.
Link: https://lore.kernel.org/r/20201125192234.2270-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Exynos5440 SoC support has been dropped since commit 8c83315da1 ("ARM:
dts: exynos: Remove Exynos5440"). Rework this driver to support DWC PCIe
variant found in the Exynos5433 SoCs.
The main difference in Exynos5433 variant is lack of the MSI support
(the MSI interrupt is not even routed to the CPU).
[mszyprow: reworked the driver to support only Exynos5433 variant,
simplified code, rebased onto current kernel code, added
regulator support, converted to the regular platform driver,
removed MSI related code, rewrote commit message, added help]
Link: https://lore.kernel.org/r/20201113170139.29956-6-m.szyprowski@samsung.com
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Currently the number of inbound and outbound iATU windows are determined
from DT properties. Unfortunately, there's 'num-viewport' for RC mode
and 'num-ib-windows' and 'num-ob-windows' for EP mode, yet the number of
windows is not mode dependent. Also, 'num-viewport' is not clear whether
that's inbound, outbound or both. We can probably assume it's outbound
windows as that's all RC mode uses.
However, using DT properties isn't really needed as the number of
regions can be detected at runtime by poking the iATU registers. The
basic algorithm is just writing a target address and reading back what
we wrote. In the unrolled ATU case, we have to take care not to go
past the mapped region.
With this, we can drop num_viewport in favor of num_ob_windows instead.
Link: https://lore.kernel.org/r/20201105211159.1814485-17-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The number of inbound and outbound windows are defined by the h/w and
apply to both RC and EP modes, so move them to the appropriate struct.
Link: https://lore.kernel.org/r/20201105211159.1814485-16-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 421063efaf.
In preparation to detect the number of iATU regions instead of using DT
properties, we need to keep reading 'num-viewport' for the Keystone
driver which doesn't use the iATU in older versions of the IP.
However, note that Keystone has been broken for some time with upstream
dts files which don't set 'num-viewports'. The reverted commit did
make the property optional, but now it's mandatory again.
Link: https://lore.kernel.org/r/20201105211159.1814485-15-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Many calls to dw_pcie_host_init() are in a wrapper function with
nothing else now. Let's remove the pointless extra layer.
Link: https://lore.kernel.org/r/20201105211159.1814485-14-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
All RC complex drivers must call dw_pcie_setup_rc(). The ordering of the
call shouldn't be too important other than being after any RC resets.
There's a few calls of dw_pcie_setup_rc() left as drivers implementing
suspend/resume need it.
Link: https://lore.kernel.org/r/20201105211159.1814485-13-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
All the DWC drivers do link setup and checks at roughly the same time.
Let's use the existing .start_link() hook (currently only used in EP
mode) and move the link handling to the core code.
The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device.
Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There are 3 possible MSI implementations for the DWC host. The first is
using the built-in DWC MSI controller. The 2nd is a custom MSI
controller as part of the PCI host (keystone only). The 3rd is an
external MSI controller (typically GICv3 ITS). Currently, the last 2
are distinguished with a .msi_host_init() hook with the 3rd option using
an empty function. However we can detect the 3rd case with the presence
of 'msi-parent' or 'msi-map' properties, so let's do that instead and
remove the empty functions.
Link: https://lore.kernel.org/r/20201105211159.1814485-10-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linuxppc-dev@lists.ozlabs.org
Platforms using the built-in DWC MSI controller all have a dedicated
interrupt with "msi" name or at index 0, so let's move setting up the
interrupt to the common DWC code.
spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so
we need to prevent configuring the MSI interrupt by setting msi_irq
to negative.
Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There's no reason for the .set_num_vectors() host op. Drivers needing a
non-default value can just initialize pcie_port.num_vectors directly.
Link: https://lore.kernel.org/r/20201105211159.1814485-8-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
