While disconnecting from the AP due to bad channel switch
params (e.g. too long Tx block), do not send the firmware
'CSA abort' before disconnecting. That causes canceling the
immediate quiet and can cause transmitting data before the
disconnection happens.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.b9af359a675f.I996fc7eb3d94e9539f8b117017c428448c42c7ad@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3_CONFIG_CMD and D0I3_END_CMD should be the last\first
command upon suspend\resume correspondingly, otherwise,
FW will raise an assert (0x342).
There are firmware notifications that cause the driver to
send a command back to the firmware. If such a notification
is sent to the driver while the the driver prepares the
firmware for D3, operation, what is likely to happen is that
the handling of the notification will try to get the mutex
and will wait unil the driver finished configuring the
firmware for D3. Then the handling notification will get
the mutex and handle the notification which will lead to
the aforementioned ASSERT 342.
To avoid this, we need to prevent any command to be sent to
the firmware between the D3_CONFIG_CMD and the D0I3_END_CMD.
Check this in the utility layer that sends the host commands
and in the transport layer as well.
Flag the D3_CONFIG_CMD and the D0I3_END_CMD commands as
commands that must be sent even if the firmware has already
been configured for D3 operation.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.1935a993b471.I3192c93c030576ca16773c01b009c4d93610d6ea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop TX'ing because we are suspending, we
have two options: either we check system_pm_mode or we
check the mvm's status that has a bit for the suspend
flow.
The latter is better because test_bit is atomic. Also
add a call to synchronize_net after we set the bit to
make sure that all the new Tx see the bit before we
actually complete the suspend flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.243c88781302.I5c0379c5a7e5d49410569e7fcd2fff7a419c6dea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of pretending to have NAPI and then relying entirely on
interrupts anyway, properly implement NAPI and schedule the poll
when we get an interrupt, re-enabling the interrupt only after
the poll completed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.a5951ac4fc06.I9c84a147288fcfb1b019572c6758f2d92949f5d7@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the new api all the flush in the FW is done before we
get the response and in the response we only get the updated
read pointer and all queued packets don't get anymore rx_tx
per packet to free the queued packet, so driver needs to free
all queued packets on flushed queue at once after flush response.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4bd0eca8c0ef.I1601aad2eb2cc83f6f73b8ca52be57bb9fd626ab@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When restarting firmware with an ongoing scheduled scan, we
don't (and shouldn't) mark it as aborted as mac80211 will be
restarting it, and so no event should go out to userspace.
The appropriate comment regarding this wasn't moved to this
place, so add it.
However, we _do_ need to clean up our internal state, since
mac80211 will restart the scan, and we'll otherwise get to
the WARN_ON() a few lines below for no reason whatsoever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4ddc9b017268.Ie869b628ae56a5d776eba0e7b7f05f42fc566f2e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing features where the firmware may send some
notifications it can often be a lot easier to do that
from a test script. Remove most injection limitations
from debugfs to be able to do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.9aff3c6b4607.I03b0ae7df094734451445ffcb7f9f0274969f1c0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't trust the firmware with the sizes (or contents)
of notifications, accessing too much data could cause page
faults if the data doesn't fit into the allocated space. This
applies more on older NICs where multiple notifications can
be in a single RX buffer.
Add a general framework for checking a minimum size of any
notification in the RX handlers and use it for most. Some RX
handlers were already checking and I've moved the checks,
some more complex checks I left and made them _NO_SIZE for
the RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.3e155d5e5f90.I2121fa4ac7cd7eb98970d84b793796646afa3eed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210128144928.2557605-1-trix@redhat.com
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210127222344.2445641-1-trix@redhat.com
Similar to mt7921 devices, introduce coredump support for mt7663 chipset
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce coredump support to mt7921 driver.
The coredump would be produced when MCU met the fatal error or driver
sent out the specific cmd to force trigger it.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Register regdomain notifier to determine the channel domain the hw scan
should rely on.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce runtime PM to mt7921 driver
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu module for suspend and WoW support and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu module for sched_scan and hw_scan and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_connac_mcu common library and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce suspend/resume and WoW (Wake-on-WoWLAN) support to mt7921
driver to allow remote wakeu-up from the suspend state.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If device has enabled beacon hw filter rx beacons are not reported to
the host. Introduce beacon_loss mcu event to trigger mac80211 mlme
connection state machine in this configuration.
IEEE80211_VIF_BEACON_FILTER has not set in vif flags since hw beacon
filter is not enabled yet
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for hw beacon filter available in the mt7921 firmware.
According to mt7921e firmware, enabling hardware filter would rely on
mt7921_mcu_uni_bss_bcnft and disabling hardware filter still rely on legacy
mt7921_mcu_set_bss_pm.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable 802.11 power-save support available in mt7921 firmware
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
introduce schedule scan to control mt7921 firmware to do background scan in
defined plan to see if the matched SSID is available.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add debugfs support to dump driver statistics and hardware details.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7921e 802.11ax (Wi-Fi 6) 2x2:2SS chipset.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Filling ieee80211_ops with the mt7921 operations.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add EEPROM support to MT7921 to determine the capability the card has
such as indentificaiton, MAC address, the band and antenna number the
card able to support.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add DMA and register access support to MT7921e driver to set up the link
for the data movement between the host and MT7921 MAC, or the host and
MT7921 MCU.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7921 contains a microprocessor with which the host can use command/event
to communicate to implement offload features such as establish connection,
hardware scan and so on. The host has to download the ROM patch, RAM
firmware and finally activate the MCU to complete the MT7921
initialization.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Rx packet description parsing, Tx packet description compositon, handle
packet recycling and provide MAC information mt76 core needs to support
mac80211.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move power_save common code shared between mt7663 and mt7921 in
mt76_connac module
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move pm mt7663 data structure in mt76_connac.h introducing
mt76_connac_pm data struct. This is a preliminary patch to share pm code
between mt7663 and mt7921
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move WoW and suspend code in mt76_connac_mcu module in order to be reused in
mt7615 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move hw_scan/sched_scan in mt76_connac_mcu module in order to be reused in
mt7615 and mt7921 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_connac common mcu library for code sharing between mt7615 and
mt7921 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_vif data structure to share common fields between
mt7615_vif and mt7921_vif and create a mcu common library
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a memory leak in mt76_add_fragment routine returning the buffer
to the page_frag_cache when we receive a new fragment and the
skb_shared_info frag array is full.
Fixes: b102f0c522 ("mt76: fix array overflow on receiving too many fragments for a packet")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/4f9dd73407da88b2a552517ce8db242d86bf4d5c.1611616130.git.lorenzo@kernel.org
When CONFIG_ATH9K is built-in but LED support is in a loadable
module, both ath9k drivers fails to link:
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_deinit_leds':
gpio.c:(.text+0x36): undefined reference to `led_classdev_unregister'
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_init_leds':
gpio.c:(.text+0x179): undefined reference to `led_classdev_register_ext'
The problem is that the 'imply' keyword does not enforce any dependency
but is only a weak hint to Kconfig to enable another symbol from a
defconfig file.
Change imply to a 'depends on LEDS_CLASS' that prevents the incorrect
configuration but still allows building the driver without LED support.
The 'select MAC80211_LEDS' is now ensures that the LED support is
actually used if it is present, and the added Kconfig dependency
on MAC80211_LEDS ensures that it cannot be enabled manually when it
has no effect.
Fixes: 197f466e93 ("ath9k_htc: Do not select MAC80211_LEDS by default")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210125113654.2408057-1-arnd@kernel.org
Failed to transmit wmi management frames:
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
CPUx (skb_deuque) CPUy (__skb_queue_tail)
next=list
prev=list
struct sk_buff *skb = skb_peek(list); WRITE_ONCE(newsk->next, next);
WRITE_ONCE(list->qlen, list->qlen - 1);WRITE_ONCE(newsk->prev, prev);
next = skb->next; WRITE_ONCE(next->prev, newsk);
prev = skb->prev; WRITE_ONCE(prev->next, newsk);
skb->next = skb->prev = NULL; list->qlen++;
WRITE_ONCE(next->prev, prev);
WRITE_ONCE(prev->next, next);
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1.c2-00033-QCAHLSWMTPLZ-1
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608618887-8857-1-git-send-email-miaoqing@codeaurora.org
When connect to an AP with WPA mode, ath10k need to set need_ptk_4_way to
firmware in WMI_PEER_ASSOC_CMD, then the data path is disallow in
firmware, it will be allowed untill firmware finish the 4 way handshake.
It failed with a test case with below steps:
1. configure AP with WPA mode with ssid1 SimpleConnect_a_orbvt_ch1,
bssid1 and channel 1.
2. connect to ssid1 and ping success.
3. wait 10 seconds which is less than
IEEE80211_SCAN_RESULT_EXPIRE(30 seconds).
4. configure AP with OPEN mode with ssid2 SimpleConnect_b_z3a00_ch1,
but use same bssid1 and channel 1 of step 1.
5. disconnect ssid1.
6. connect to ssid2 and ping fail.
Fail reason:
When run step 6, ath10k_peer_assoc_h_crypto() called cfg80211_get_bss()
with bssid and chan info, but ssid1 and ssid2 have the same bssid and
channel, then there have 2 entry for ssid1 and ssid2 in cfg80211. The
ssid1's order is before ssid2 in bss_list, and ssid1's age is less than
the expire time which is IEEE80211_SCAN_RESULT_EXPIRE(30 seconds). Then
ssid1's entry is selected and ath10k_peer_assoc_h_crypto() parsed it and
get the rsnie and then need_ptk_4_way is set to firmware, so data path
is disallowed and it will not receive 4 way handshake for OPEN mode,
so ping fail in step 6.
This patch is to pass the ssid info to cfg80211_get_bss() as same as
cfg80211_mlme_assoc() and cfg80211_mlme_auth(), then it will find the
correct bss entry in above test case, then case success.
For AP mode, the ssid info is filled in ieee80211_start_ap(), for STATION
mode, it is filled in ieee80211_mgd_assoc(). Tested for both AP/STATION
mode with QCA6174 hw3.2 PCI, it is success start/connect/ping for
WPA/OPEN mode.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607312195-3583-3-git-send-email-wgong@codeaurora.org
ath10k assigns ath10k_mac_set_sar_specs to ath10k_ops, and
this function is called when user space application calls
NL80211_CMD_SET_SAR_SPECS. ath10k also registers SAR type,
and supported frequency ranges to wiphy so user space can
query SAR capabilities.
This SAR power limitation is compared to regulatory txpower
and selects the minimal one to set when station is connected.
Otherwise, it delays until the station is connected. If the
station is disconnected, it returns to regulatory txpower.
This feature is controlled by hw parameter: dynamic_sar_support.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203103728.3034-4-cjhuang@codeaurora.org
Fix a regression where everything in virt_wifi would just hang. This
happened due to overlapping changes between commit a05829a722
("cfg80211: avoid holding the RTNL when calling the driver") which
had originally needed to change the locking, but then I introduced
commit 2fe8ef1062 ("cfg80211: change netdev registration/unregistration
semantics") instead. virt_wifi somehow fell through the cracks when
I undid all the previous locking changes. Fix it now.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Reported-by: syzbot+3d2d5e6cc3fb15c6a0fd@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210127215941.2d6a97b09784.I4f1fac32f67045171be50931f44d77e150911bee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With a maximum length of 7991, the radio sometimes locks up under load when
transmitting A-MSDU frames to lots of stations. Using the lower limit makes
it work reliably again
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of holding it for the duration of an entire station schedule run,
which can block out competing tasks for a significant amount of time,
only hold it for scheduling one batch of packets for one station.
Improves responsiveness under load
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to commit '0e40dbd56d67 ("mt7601u: process URBs in status EPROTO
properly")', do no schedule rx_worker for urb marked with status set
-EPROTO
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For performance reasons, mt7915 supports using 2 PCIE gen1 links on
platforms that don't support gen2.
Add support for using this to move traffic for a second DBDC band onto
a dedicated link
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only clear dev->phy2 after the phy is gone, the driver may still need to access
it until shutdown is complete
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, TxBF can be run on both bands simultaneously.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mcu country code running mt7615_mcu_set_channel_domain routine in
mt7615_regd_notifier().
Filter out disabled channels in mt7615_mcu_set_channel_domain().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM band fields contain default values, assign 2.4 GHz to the
first band and 5 GHz to the second.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes allover the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgD96RAAoJEG4XJFUm622bubwH/2TxF5aLNnE49BdgksiorD1M
lr6r1QveG/VQkSVdecYV6wmJ/nzzR46Q3c7Ez3ZBnLpboSDmyK7gKIeGlHSLmMwC
YYt3Fnj1XF/UgPs+daCiF/yxz3v7lsDicl8wKYQgpKU/jDj8dfQ/ntM5p3s0tc5O
JaiWeDGQQRgbyE9g3enqW0vho/6luxI0MIOwcSnCLidsM6oAQowbmtzXDpmwagiR
Xyi0eLzSHSCOmH41VNphDZzlL61C6yCLavNpCvCxv/bElTX7XXynwiw3+i8FiU14
TQabyv0z0yd3pVCYp88TFf9cDe7uQ8MS6NG5CoYP3RXHJ1pDEy3a8yBBc1dp2Tc=
=a+lu
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes all over the driver
* tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: (24 commits)
mt7601u: fix kernel crash unplugging the device
iwlwifi: queue: bail out on invalid freeing
iwlwifi: mvm: guard against device removal in reprobe
iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit.
iwlwifi: mvm: clear IN_D3 after wowlan status cmd
iwlwifi: pcie: add rules to match Qu with Hr2
iwlwifi: mvm: invalidate IDs of internal stations at mvm start
iwlwifi: mvm: fix the return type for DSM functions 1 and 2
iwlwifi: pcie: reschedule in long-running memory reads
iwlwifi: pcie: use jiffies for memory read spin time limit
iwlwifi: pcie: fix context info memory leak
iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmap
iwlwifi: pcie: set LTR on more devices
iwlwifi: queue: don't crash if txq->entries is NULL
iwlwifi: fix the NMI flow for old devices
iwlwifi: pnvm: don't try to load after failures
iwlwifi: pnvm: don't skip everything when not reloading
iwlwifi: pcie: avoid potential PNVM leaks
iwlwifi: mvm: take mutex for calling iwl_mvm_get_sync_time()
iwlwifi: mvm: skip power command when unbinding vif during CSA
...
====================
Link: https://lore.kernel.org/r/20210126092202.6A367C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/core/tso.c got recent support for USO, and this broke iwlfifi
because the driver implemented a limited form of GSO.
Providing ->gso_type allows for skb_is_gso_tcp() to provide
a correct result.
Fixes: 3d5b459ba0 ("net: tso: add UDP segmentation support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209913
Link: https://lore.kernel.org/r/20210125150949.619309-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It causes high CPU load on the WA core, which can lead to extra latency when
using many stations. Dropping packets for long queues is managed by mac80211
fq_codel instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for passing flags for selecting the MCU target and query type
instead of trying to detect it based on the command id
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is causing some extreme latency spikes when sending traffic to
multiple stations at the same time. Disable this until the firmware issue
is sorted out
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add ht/vht implicit Tx beamforming support and enable it via debugfs.
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch for implicit beamforming support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When testmode can be enabled, the start() callback would already be
called, causing that txpower sku feature isn't really disabled after
testmode is enabled. This patch fix the issue.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Implement continuous tx state for MT7915 NIC testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to simplify setting state in mt7915
testmode, for adding the new continuous tx state.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support to set a special tx state in testmode: continuous tx,
which is used for sending tx without time gap.
Note that continuous tx mode doesn't send real packets, instead, it's
pure phy signal, and the waveform can be observed by instrument.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a testmode mcu command to clean up hw tx queue before a new
testmode tx starts.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If tx_time is set, calculate a new packet length based on tx time and
tx rate.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to calculate and apply ipg parameters in testmode
for MT7915 NIC.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Split parameter settings and mcu command update in mt7915_mcu_set_tx().
This is for reusing edca update function in testmode ipg setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Originally, tx queued limit is set to 1000 to prevent from running out
of tx token. If a new testmode tx is triggered while the previous one
hasn't finished yet, we'll wait a period of time until tx_done equals to
tx_queued. Normally, current queued limit can finish in 10 seconds.
However, if ipg is configured to a larger value, less than 1000 packets
can be done in the default timeout period, which may lead to a crash
when a new testmode tx triggered.
To deal with this, make tx queued limit dynamically adjusted according
to ipg value.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add attributes for setting tx inter-packet gap (ipg), duty cycle, and
transmission time in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add spatial extension (spe) index as a configurable parameter in testmode.
This is used for specifically configuring TX path, such as different
WF TX priority, number of antennas and spatial streams.
If spe_idx is not set, TX path depends on tx_antenna_mask; otherwise,
both spe_idx and tx_antenna_mask are referenced to decide TX path.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LDPC should be set when bw is larger than 20MHz to make
testmode tx work normally.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move chainmask from driver phy to mt76_phy since it is used by all
drivers. This is a preliminary patch to create a common mcu library used
by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mac_work delayed_work and mac_work_count in mt76_phy since it is
used by all drivers. This is a preliminary patch to create a common mcu
library used by mt7615 and mt7921 drivers
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move per-chip testmode data to mt7615_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move per-chip testmode data to mt7915_phy, to properly support
reg_backup and rx status of each band in testmode.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move testmode mtd variables to mt76_dev, since they are the same on
each phy.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add testmode support for DBDC NICs (both MT7615D and MT7915D work).
Testmode data and parameters are moved from per-dev to per-phy
for maintaining the value of each band.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch for DBDC and ipg config support
in testmode.
The wmm_idx of band1 should be configured by this command to
make band1 Tx work normally. Also, for setting ipg, FW needs a
non-empty bss_info structure to do edca parameters update.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware wouldn't add LLC-SNAP when skb->data_len is 0, which causes
Tx hang, so add a check to drop this kind of packet.
Tested-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in mt7915_mcu_set_radar_th routine:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: expected unsigned int [usertype] min_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3154:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: expected unsigned int [usertype] max_pri
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3155:17: got restricted __le32 [usertype]
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: warning: incorrect type in initializer (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: expected unsigned int [usertype] min_stgpr_diff
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:3162:17: got restricted __le32 [usertype]
Fixes: cee236e148 ("mt76: mt7915: fix endian issues")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for getting rf values from flash.
This is used for some test purposes and products.
If the mtd partition is configured in dts, driver will read from flash
to init eeprom command; if not, still init it with efuse's values.
An example:
&slot0 {
mt7915@0,0 {
reg = <0x0000 0 0 0 0>;
device_type = "pci";
mediatek,mtd-eeprom = <&factory 0x0000>;
};
};
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid races, run mt7915_configure_filter routine holding
mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reset token in mt7615_mac_reset_work() to avoid possible leakege.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reset buffering token in mt7915_mac_reset_work() to avoid possible leakege,
which leads to Tx stop after mac reset.
Tested-by: Bo Jiao <bo.jiao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MCU expects to set WLAN_CIPHER_SUITE_CCMP and WLAN_CIPHER_SUITE_AES_CMAC
at the same time, so adding an intermediate buffer for batch update.
Tested-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
memcpy operation is next to memset code, and the size to copy is equals to the size to
memset, so the memset operation is unnecessary, remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201223012516.24286-1-zhengyongjun3@huawei.com
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have already WARN_ON(!qc) for non-QOS frame on txq->sched_retry path,
but we continue to process, what makes no sense since tid is not
initialized. Non QOS frame should never happen when aggregation
is enabled on queue, so do not process that.
Patch should fix smatch warning:
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2822 il4965_hdl_tx() error: uninitialized symbol 'tid'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210119100621.439134-1-stf_xl@wp.pl
We can currently get a "command execute failure 19" error on beacon loss
if the signal is weak:
wlcore: Beacon loss detected. roles:0xff
wlcore: Connection loss work (role_id: 0).
...
wlcore: ERROR command execute failure 19
...
WARNING: CPU: 0 PID: 1552 at drivers/net/wireless/ti/wlcore/main.c:803
...
(wl12xx_queue_recovery_work.part.0 [wlcore])
(wl12xx_cmd_role_start_sta [wlcore])
(wl1271_op_bss_info_changed [wlcore])
(ieee80211_prep_connection [mac80211])
Error 19 is defined as CMD_STATUS_WRONG_NESTING from the wlcore firmware,
and seems to mean that the firmware no longer wants to see the quirk
handling for WLCORE_QUIRK_START_STA_FAILS done.
This quirk got added with commit 18eab43070 ("wlcore: workaround
start_sta problem in wl12xx fw"), and it seems that this already got fixed
in the firmware long time ago back in 2012 as wl18xx never had this quirk
in place to start with.
As we no longer even support firmware that early, to me it seems that it's
safe to just drop WLCORE_QUIRK_START_STA_FAILS to fix the error. Looks
like earlier firmware got disabled back in 2013 with commit 0e284c074e
("wl12xx: increase minimum singlerole firmware version required").
If it turns out we still need WLCORE_QUIRK_START_STA_FAILS with any
firmware that the driver works with, we can simply revert this patch and
add extra checks for firmware version used.
With this fix wlcore reconnects properly after a beacon loss.
Cc: Raz Bouganim <r-bouganim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210115065613.7731-1-tony@atomide.com
The LTR mechanism enables PCIE Endpoints to report the service latency
requirements and CPU will enter appropriate sleep state to save power
based on the LTR value.
8723de provides two registers to config the LTR, and the original setting
is too short for CPU to ente sleep state. The patch adjust the LTR setting.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210113014342.3615-1-pkshih@realtek.com
There are certain conditional expressions in rtl8821ae, where a boolean
variable is compared with true/false, in forms such as (foo == true) or
(false != bar), which does not comply with checkpatch.pl (CHECK:
BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
E.g., in drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c,
"if (rtlefuse->autoload_failflag == false)" can be replaced with
"if (!rtlefuse->autoload_failflag)"
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210110121525.2407-6-yashsri421@gmail.com
There are certain conditional expressions in rtl8192se, where a boolean
variable is compared with true/false, in forms such as (foo == true) or
(false != bar), which does not comply with checkpatch.pl (CHECK:
BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210110121525.2407-5-yashsri421@gmail.com
There are certain conditional expressions in rtl8188ee, where a boolean
variable is compared with true/false, in forms such as (foo == true) or
(false != bar), which does not comply with checkpatch.pl (CHECK:
BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
E.g., in drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c,
"if (mac->act_scanning == true)" can be replaced with
"if (mac->act_scanning)"
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210110121525.2407-4-yashsri421@gmail.com
There are certain conditional expressions in rtl8192c-common, where a
boolean variable is compared with true/false, in forms such as
(foo == true) or (false != bar), which does not comply with checkpatch.pl
(CHECK: BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
E.g., in drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c,
"else if (initialized == false) {" can be replaced with
"else if (!initialized) {"
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210110121525.2407-3-yashsri421@gmail.com
There are certain conditional expressions in rtl_pci, where a boolean
variable is compared with true/false, in forms such as (foo == true) or
(false != bar), which does not comply with checkpatch.pl (CHECK:
BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
E.g., in drivers/net/wireless/realtek/rtlwifi/ps.c,
"if (find_p2p_ie == true)" can be replaced with "if (find_p2p_ie)"
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210110121525.2407-2-yashsri421@gmail.com
If we find an entry without an SKB, we currently continue, but
that will just result in an infinite loop since we won't increment
the read pointer, and will try the same thing over and over again.
Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.abe2dedcc3ac.Ia6b03f9eeb617fd819e56dd5376f4bb8edc7b98a@changeid
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
In D3 resume flow, avoid the following race where sending
packets before updating the sequence number (sequence
number received from the wowlan status command response):
Thread 1:
__iwl_mvm_resume clears IWL_MVM_STATUS_IN_D3 and is cut
by thread 2 before reaching iwl_mvm_query_wakeup_reasons.
Thread 2:
iwl_mvm_mac_itxq_xmit calls iwl_mvm_tx_skb since
IWL_MVM_STATUS_IN_D3 is not set using a wrong sequence number.
Thread 1:
__iwl_mvm_resume continues and calls iwl_mvm_query_wakeup_reasons
updating the sequence number received from the firmware.
The next packet that will be sent now will cause sysassert 0x1096.
Fix the bug by moving 'clear IWL_MVM_STATUS_IN_D3' to after
sending the wowlan status command and updating the sequence
number.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.fe927ec939c6.I103d3321fb55da7e6c6c51582cfadf94eb8b6c58@changeid
Having sta_id not set for aux_sta and snif_sta can potentially lead to a
hard to debug issue in case remove station is called without an add. In
this case sta_id 0, an unrelated regular station, will be removed.
In fact, we do have a FW assert that occures rarely and from the debug
data analysis it looks like sta_id 0 is removed by mistake, though it's
hard to pinpoint the exact flow. The WARN_ON in this patch should help
to find it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5dc6dd9b22d5.I2add1b5ad24d0d0a221de79d439c09f88fcaf15d@changeid
The return type value of functions 1 and 2 were considered to be an
integer inside a buffer, but they can also be only an integer, without
the buffer. Fix the code in iwl_acpi_get_dsm_u8() to handle it as a
single integer value, as well as packed inside a buffer.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Fixes: 9db93491f2 ("iwlwifi: acpi: support device specific method (DSM)")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5757092adcd6.Ic24524627b899c9a01af38107a62a626bdf5ae3a@changeid
If we spin for a long time in memory reads that (for some reason in
hardware) take a long time, then we'll eventually get messages such
as
watchdog: BUG: soft lockup - CPU#2 stuck for 24s! [kworker/2:2:272]
This is because the reading really does take a very long time, and
we don't schedule, so we're hogging the CPU with this task, at least
if CONFIG_PREEMPT is not set, e.g. with CONFIG_PREEMPT_VOLUNTARY=y.
Previously I misinterpreted the situation and thought that this was
only going to happen if we had interrupts disabled, and then fixed
this (which is good anyway, however), but that didn't always help;
looking at it again now I realized that the spin unlock will only
reschedule if CONFIG_PREEMPT is used.
In order to avoid this issue, change the code to cond_resched() if
we've been spinning for too long here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 04516706bb ("iwlwifi: pcie: limit memory read spin time")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.217a9d6a6a12.If964cb582ab0aaa94e81c4ff3b279eaafda0fd3f@changeid
There's no reason to use ktime_get() since we don't need any better
precision than jiffies, and since we no longer disable interrupts
around this code (when grabbing NIC access), jiffies will work fine.
Use jiffies instead of ktime_get().
This cleanup is preparation for the following patch "iwlwifi: pcie: reschedule
in long-running memory reads". The code gets simpler with the weird clock use
etc. removed before we add cond_resched().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.621c948b1fad.I3ee9f4bc4e74a0c9125d42fb7c35cd80df4698a1@changeid
To avoid completion timeouts during device boot, set up the
LTR timeouts on more devices - similar to what we had before
for AX210.
This also corrects the AX210 workaround to be done only on
discrete (non-integrated) devices, otherwise the registers
have no effect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: edb625208d ("iwlwifi: pcie: set LTR to avoid completion timeout")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.fb819e19530b.I0396f82922db66426f52fbb70d32a29c8fd66951@changeid
The code was really awkward, we would first dereference
txq->entries when calling iwl_txq_genX_tfd_unmap and then
we would check that txq->entries is non-NULL.
Fix that by exiting if txq->entries is NULL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.173359fc236d.I75c7c2397d20df8d7fbc24cb16a5232d5c551889@changeid
I noticed that the flow that triggers an NMI on the firmware
for old devices (tested on 7265) doesn't work.
Apparently, the firmware / device is still in low power when
we write the register that triggers the NMI. We call the
"grab_nic_access" function to make sure the device is awake
but that wasn't enough. I played with this and noticed that
if we wait 1 ms after the device reports it is awake before
we write to the NMI register, the device always sees our
write and the firmware gets properly asserted.
Triggering an NMI to the firmware can be done with the
debugfs hook:
echo 1 > /sys/kernel/debug/iwlwifi/0000\:00\:03.0/iwlmvm/fw_nmi
What happened before is that the firmware would just stall
without running its NMI routine. Because of that the driver
wouldn't get the "firmware crashed" interrupt. After a while
the driver would notice that the firmware is not responding
to some command and it would read the error data from the
firmware, but this data is populated in the NMI service
routine in the firmware which was not called. So in the logs
it looked like:
iwlwifi 0000:00:03.0: Error sending REPLY_ERROR: time out after 2000ms.
iwlwifi 0000:00:03.0: Current CMD queue read_ptr 33 write_ptr 34
iwlwifi 0000:00:03.0: Loaded firmware version: 29.09bd31e1.0 7265D-29.ucode
iwlwifi 0000:00:03.0: 0x00000000 | ADVANCED_SYSASSERT
iwlwifi 0000:00:03.0: 0x00000000 | trm_hw_status0
iwlwifi 0000:00:03.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:00:03.0: 0x00000000 | branchlink2
iwlwifi 0000:00:03.0: 0x00000000 | interruptlink1
iwlwifi 0000:00:03.0: 0x00000000 | interruptlink2
iwlwifi 0000:00:03.0: 0x00000000 | data1
iwlwifi 0000:00:03.0: 0x00000000 | data2
iwlwifi 0000:00:03.0: 0x00000000 | data3
iwlwifi 0000:00:03.0: 0x00000000 | beacon time
iwlwifi 0000:00:03.0: 0x00000000 | tsf low
...
With this fix, immediately after we trigger the NMI to the
firmware, we get the expected:
iwlwifi 0000:00:03.0: Microcode SW error detected. Restarting 0x2000000.
iwlwifi 0000:00:03.0: Start IWL Error Log Dump:
iwlwifi 0000:00:03.0: Status: 0x00000040, count: 6
iwlwifi 0000:00:03.0: Loaded firmware version: 29.09bd31e1.0 7265D-29.ucode
iwlwifi 0000:00:03.0: 0x00000084 | NMI_INTERRUPT_UNKNOWN
iwlwifi 0000:00:03.0: 0x000002F1 | trm_hw_status0
iwlwifi 0000:00:03.0: 0x00000000 | trm_hw_status1
iwlwifi 0000:00:03.0: 0x00043D6C | branchlink2
iwlwifi 0000:00:03.0: 0x0004AFD6 | interruptlink1
iwlwifi 0000:00:03.0: 0x000008C4 | interruptlink2
iwlwifi 0000:00:03.0: 0x00000000 | data1
iwlwifi 0000:00:03.0: 0x00000080 | data2
iwlwifi 0000:00:03.0: 0x07030000 | data3
iwlwifi 0000:00:03.0: 0x003FD4C3 | beacon time
iwlwifi 0000:00:03.0: 0x00C22AC3 | tsf low
iwlwifi 0000:00:03.0: 0x00000000 | tsf hi
iwlwifi 0000:00:03.0: 0x00000000 | time gp1
iwlwifi 0000:00:03.0: 0x00C22AC3 | time gp2
iwlwifi 0000:00:03.0: 0x00000001 | uCode revision type
iwlwifi 0000:00:03.0: 0x0000001D | uCode version major
Notice the first line: "Microcode SW error detected:" which
is printed in the driver's ISR, which means that the driver
actually got an interrupt from the firmware saying that it
crashed. And then we have the properly populated error data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.70e67cc75d88.I6615cad4361862e7f3c9f2d3cafb6a8c61e16781@changeid
If loading the PNVM file failed on the first try during the
interface up, the file is unlikely to show up later, and we
already don't try to reload it if it changes, so just don't
try loading it again and again.
This also fixes some issues where we may try to load it at
resume time, which may not be possible yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6972592850 ("iwlwifi: read and parse PNVM file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.5ac6828a0bbe.I7d308358b21d3c0c84b1086999dbc7267f86e219@changeid
If we erroneously try to set the PNVM data again after it has
already been set, we could leak the old DMA memory. Avoid that
and warn, we shouldn't be doing this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6972592850 ("iwlwifi: read and parse PNVM file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.929c2d680429.I086b9490e6c005f3bcaa881b617e9f61908160f3@changeid
In the new CSA flow, we remain associated during CSA, but
still do a unbind-bind to the vif. However, sending the power
command right after when vif is unbound but still associated
causes FW to assert (0x3400) since it cannot tell the LMAC id.
Just skip this command, we will send it again in a bit, when
assigning the new context.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.64a2254ac5c3.Iaa3a9050bf3d7c9cd5beaf561e932e6defc12ec3@changeid
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removed the duplicated peer related function declaration
from core.h since those functions are already declared in peer.h
Founded in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608304793-20612-1-git-send-email-periyasa@codeaurora.org
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200205191043.21913-1-linus.luessing@c0d3.blue
Function ep_rx_complete is being called without NULL checking
in ath10k_htc_rx_completion_handler. Without such check, mal-
formed packet is able to cause jump to NULL.
ep->service_id seems a good candidate for sanity check as it is
used in usb.c.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622022055.16028-1-bruceshenzk@gmail.com
We can get the following in the logs every few minutes or so:
wlcore: ERROR exceeded max RX BA sessions
Let's downgrade the message to a debug message as suggested by the TI
support folks at:
https://e2e.ti.com/support/wireless-connectivity/wifi/f/968/p/352435/1244754
"The WL127x firmware supports max of 3 BA sessions. It cannot be increased.
I think the problem here is the peer trying to initiate a 4th BA session
(ADDBA request)."
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210101065955.63386-1-tony@atomide.com
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
A null pointer will be passed to a kfree() call after a kzalloc() call failed.
This code is useless. Thus delete the extra function call.
A goto statement is also no longer needed. Thus adjust an if branch.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201222135113.20680-1-zhengyongjun3@huawei.com
When the usb device being plugged out, before ieee80211 gets to know the
hw being removed, it gets to know that the association status changed,
and thus ask for the device to do the calibration. This causes error as
the hw is absent.
This can be avoid by checking the status of the device before sending
the calibration request to the device.
Signed-off-by: Zhi Han <z.han@gmx.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201217161657.GB12562@E480
When the usb device being plugged out, before the usb_driver:disconnect
called by e.g workqueue, it is possible that some URBs are still in
processing, and being marked as EPROTO in host controller.
Those URBs should not be scheduled in complete_rx callback function to
get further processing.
Signed-off-by: Zhi Han <z.han@gmx.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201217161302.GA12562@E480
This adds support for the BCM43666/4 which seems to be using the same
firmware as BCM4366 (4366c0). I found it in the Netgear R8000P router.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214101553.32097-1-zajec5@gmail.com
As the Marvell PCIE WiFi-Ex driver does not have any code or data
located in initmem, there is no need to annotate the mwifiex_pcie
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211133835.2970384-1-geert+renesas@glider.be
Fix the following coccicheck warning:
./drivers/net/wireless/realtek/rtw88/debug.c:800:17-23: WARNING:
Comparison of 0/1 to bool variable
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1610445040-23599-1-git-send-email-abaci-bugfix@linux.alibaba.com
To protect both of WL/BT performance while BT is under re-link state.
4-slot mode TDMA can make the re-link more sensitive and mitigate the WL
throughput drop.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210112021135.3823-1-pkshih@realtek.com
Hal function must follow the value that calculates from dynamic mechanism.
Force to set new_lvl to 4 damages receiving ability. System will not able
to reconnect to the AP if wifi unexpected disconnecting at this moment.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201228082516.16488-1-pkshih@realtek.com
Sometimes driver does not get tx report from firmware because wifi
environment is too noisy to get ack from AP about a TX frame,
or firmware is too busy to report driver in a estimated time.
But the condition will not affect wifi function or throughput.
So we reduce the log level to rtw_debug instead of scary backtrace.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201228082433.16431-1-pkshih@realtek.com
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201216130442.13869-1-zhengyongjun3@huawei.com
Clang warns in both mt7615 and mt7915:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:271:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:278:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WA;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:282:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WM;
~ ^~~~~~~~~~
3 warnings generated.
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:238:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_WM;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:240:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
2 warnings generated.
Use the proper type for the queue ID variables to fix these warnings.
Additionally, rename the txq variable in mt7915_mcu_send_message to be
more neutral like mt7615_mcu_send_message.
Fixes: e637763b60 ("mt76: move mcu queues to mt76_dev q_mcu array")
Link: https://github.com/ClangBuiltLinux/linux/issues/1229
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201229211548.1348077-1-natechancellor@gmail.com
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a970650 ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJf4h9uAAoJEG4XJFUm622byVMIAIwMhqVmDL7jqqOwd2xZa4jf
/QzAvx7tize/tBF6FubOpF+Bxzn4XaJzwFE97B0wwO6/rnxD2a56WUARuYF8ztnT
St18uYBU23n+QKfvL1qJI5Az0JXxia/cLDwvr8YPK3rmh2jmSOVyJSCUtHSJ+yQ2
hnJA3Af8ves3VpCZ2jqF7VcHM/xYfmoJZy3I7P6LpT5m+6FOqqdN8Mx6ei2aHEzY
+HHN26QoW35N2DCna+iTtEMpepWU8eoJmIOU+t881bRfZBoczc+WH99ZlSaVDUug
hl+Hy5bwDzN+HdGziSgWP6U5a+XNjRu6Y5dUpEm4YmL+uJeU4NPc0Q35nyx4RBM=
=fjHi
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
* tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
MAINTAINERS: switch to different email address
mt76: mt7915: fix MESH ifdef block
mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
mt76: sdio: remove wake logic in mt76s_process_tx_queue
mt76: usb: remove wake logic in mt76u_status_worker
ath11k: pci: disable ASPM L0sLs before downloading firmware
ath11k: qmi: try to allocate a big block of DMA memory first
rtlwifi: rise completion at the last step of firmware callback
mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
ath11k: Fix ath11k_pci_fix_l1ss()
ath11k: Fix error code in ath11k_core_suspend()
ath11k: start vdev if a bss peer is already created
ath11k: fix crash caused by NULL rx_channel
ath11k: add missing null check on allocated skb
====================
Link: https://lore.kernel.org/r/20201222163727.D4336C433C6@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a build error when CONFIG_MAC80211_MESH is not enabled:
../drivers/net/wireless/mediatek/mt76/mt7915/init.c:47:2: error: expected expression before '}' token
}, {
^
Fixes: af901eb4ab ("mt76: mt7915: get rid of dbdc debugfs knob")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Shayne Chen <shayne.chen@mediatek.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201218173202.23159-1-rdunlap@infradead.org
Similar to mmio/usb code path, remove wake logic in mt76s_process_tx_queue
routine. Starting from commit 90d494c99a ("mt76: improve tx queue
stop/wake"), the wake queue logic on the sdio status path is no longer
necessary since the hw queues are no longer stopped on the mt76 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d2d7d9d437f4dec2ef1df0ed070b9cf299f021ad.1607164041.git.lorenzo@kernel.org
Similar to mmio code path, remove wake logic in mt76u_status_worker handler.
Starting from commit 90d494c99a ("mt76: improve tx queue stop/wake")', the
wake queue logic on the usb status path is no longer necessary since the hw
queues are no longer stopped on the mt76 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/00009bf0cfdc9565e4432cad3ed51888c667c25d.1607164041.git.lorenzo@kernel.org
ath.git fixes for 5.11. Major changes:
ath11k
* add null check for skb allocation
* fix crash found during connect/disconnect stress testing
* fix for HT disabled case
* brown paperbag fixes for my bugs in suspend code
* fix an unnecessary qmi allocation during firmware bootup
* disable ASPM during firmware bootup to avoid issues
The "&ar->ab->base_lock" and "&ab->base_lock" locks are the same lock
but it's nicer to use the same name consistently everywhere.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9s7QAHDM2OTIo3a@mwanda
Sometimes QCA6390 doesn't switch to amss state as device enters
L1ss state, so disable L0sL1s during firmware downloading.
Driver recovers the ASPM to default value in start callback
or powerdown callback.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608218530-15426-1-git-send-email-kvalo@codeaurora.org
Not all firmware versions support allocating DMA memory in smaller blocks so
first try to allocate big block of DMA memory for QMI. If the allocation fails,
let firmware request multiple blocks of DMA memory with smaller size.
This also fixes an unnecessary error message seen during ath11k probe on
QCA6390:
ath11k_pci 0000:06:00.0: Respond mem req failed, result: 1, err: 0
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-22
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608127593-15192-1-git-send-email-kvalo@codeaurora.org
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-5-jouni@codeaurora.org
Now that ath/key.c may not be explicitly clearing keys from the key
cache, clear all key cache entries when disabling hardware to make sure
no keys are left behind beyond this point.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-3-jouni@codeaurora.org
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org
When the wlan is disabled, i.e when all the interfaces are
deleted, voltage regulator votes are not removed. This leads
to more power consumption even when wlan is disabled.
Move the adding/removing of voltage regulator votes as part
of hif power on/off in SNOC targets, so that these voltage
regulator votes are there only when wlan is enabled.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607713230-18382-1-git-send-email-pillair@codeaurora.org
Currently if the copy engine pipe init fails for snoc based
chipsets, the rri is not freed.
Fix this error handling for copy engine pipe init
failure.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 4945af5b26 ("ath10k: enable SRRI/DRRI support on ddr for WCN3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607713210-18320-1-git-send-email-pillair@codeaurora.org
All these conditions are reversed so presumably most of the function is
dead code. This caused a spurious warning:
[ 95.734922] ath11k_pci 0000:06:00.0: failed to set sysclk: 0
Fixes: 0699940755 ("ath11k: pci: fix L1ss clock unstable problem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9nGDHiTh+Z+asDy@mwanda
The "if (!ret)" condition is inverted and it should be "if (ret)". It means
that we return success when we had intended to return an error code. This also
caused a spurious warning even when the suspend was successful:
[ 297.186612] ath11k_pci 0000:06:00.0: failed to suspend hif: 0
Fixes: d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9nF17L2/EKOSbn/@mwanda
For QCA6390, bss peer must be created before vdev is to start. This
change is to start vdev if a bss peer is created. Otherwise, ath11k
delays to start vdev.
This fixes an issue in a case where HT/VHT/HE settings change between
authentication and association, e.g., due to the user space request
to disable HT.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211051358.9191-1-cjhuang@codeaurora.org
Currently the null check on a newly allocated skb is missing and
this can lead to a null pointer dereference is the allocation fails.
Fix this by adding a null check and returning -ENOMEM.
Addresses-Coverity: ("Dereference null return")
Fixes: 43ed15e1ee ("ath11k: put hw to DBS using WMI_PDEV_SET_HW_MODE_CMDID")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214232417.84556-1-colin.king@canonical.com
Now that relay_open() accepts const callbacks, make relay callbacks
const.
Link: https://lkml.kernel.org/r/7db0286c428f3a478dd7544afef04a3b131f1aa0.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that relay_open() accepts const callbacks, make relay callbacks
const.
Link: https://lkml.kernel.org/r/44e3d65b71025c462948d0c554061dc7b40ab488.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that relay_open() accepts const callbacks, make relay callbacks const.
Link: https://lkml.kernel.org/r/85cabc6d4b0d0ca43d4e0fb94897ccd16e3b7930.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ath.git patches for v5.11. Major changes:
ath11k
* suspend support for QCA6390 PCI devices
* support TXOP duration based RTS threshold
* mesh: add support for 256 bitmap in blockack frames in 11ax
Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.
At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.
During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state. During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org
Add ce irq enable and disable hif layer functions, so core module can enable
enable them without cleaning pipe and refilling pipe. Needed for suspend.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-10-git-send-email-kvalo@codeaurora.org
Implement wow enable ane wow wakeup commands which are needed for suspend.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-9-git-send-email-kvalo@codeaurora.org
Firmware will check all the pipes before entering WoW mode during suspend. If
ATH11K_HTC_FLAG_NEED_CREDIT_UPDATE is set, firmware treats this pipe needed to
return credit even though it's actually not required. If any pipe needs to
return credit, the suspend_complete message doesn't send to host but is
dropped. So host gets time out and WoW suspend failed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-8-git-send-email-kvalo@codeaurora.org
Stop dp rx pktlog when entering suspend and reap the mon_status buffer to keep
it empty. During resume restart the reap timer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-7-git-send-email-kvalo@codeaurora.org
When ath11k sends suspend command to firmware, firmware will
return suspend_complete events and add handlers for those.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-6-git-send-email-kvalo@codeaurora.org
Just when resume from WoW, the write to select_window doesn't take
effect immediately, so read the register again to ensure the write
operation is finished.
Another change is to reset select_window to ZERO because this
register isn't restored after WoW, so the content of this register
becomes ZERO too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-4-git-send-email-kvalo@codeaurora.org
For suspend support add suspend and resume to HIF layer. These ops are optional
and, for example, AHB bus driver does not need to implement these.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-3-git-send-email-kvalo@codeaurora.org
MHI suspend and resume isn't hooked in ath11k yet, so hook these
functions needed for suspend support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-2-git-send-email-kvalo@codeaurora.org
Currently 6G specific tlvs have duplicate entries which is causing
scan failures. Fix this by removing the duplicate entries of the same
tlv. This also fixes out-of-bound memory writes caused due to
adding tlvs when num_hint_bssid and num_hint_s_ssid are ZEROs.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Fixes: 74601ecfef ("ath11k: Add support for 6g scan hint")
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-7-git-send-email-kvalo@codeaurora.org
It's recommended to disable VDD4BLOW during initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-6-git-send-email-kvalo@codeaurora.org
For QCA6390, one PCI related clock drifts sometimes, and
it makes PCI link difficult to quit L1ss. Fix it by writing
some registers which are known to fix the problem.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-5-git-send-email-kvalo@codeaurora.org
For QCA6390, host needs to reset some registers before MHI power up to fix PCI
link unstable issue if hot reset happened. Also clear all pending interrupts
during power up.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-4-git-send-email-kvalo@codeaurora.org
It's recommended to use wmi command WMI_PDEV_SET_HW_MODE_CMDID to put hardware
to dbs mode instead of wmi_init command. This fixes a few strange stability
issues.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-3-git-send-email-kvalo@codeaurora.org
There was no way to detect if the firmware crashed so add a warning. At the
moment the firmware is not restarted or anything like that, so when this
happens ath11k modules need to be reloaded.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-2-git-send-email-kvalo@codeaurora.org
Use MHI provided APIs to allocate and free MHI controller to
improve MHI host driver handling. This also fixes a memory leak
as the MHI controller was allocated but never freed.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605634436-36506-1-git-send-email-bbhatt@codeaurora.org
When it has more than one restart_work queued meanwhile, the 2nd
restart_work is very easy to break the 1st restart work and lead
recovery fail.
Add a flag to allow only one restart work running untill
device successfully recovered.
It already has flag ATH10K_FLAG_CRASH_FLUSH, but it can not use this
flag again, because it is clear in ath10k_core_start. The function
ieee80211_reconfig(called by ieee80211_restart_work) of mac80211 do
many things and drv_start(call to ath10k_core_start) is 1st thing,
when drv_start complete, it does not mean restart complete. So it
add new flag and clear it in ath10k_reconfig_complete, because it
is the last thing called from drv_reconfig_complete of function
ieee80211_reconfig, after it, the restart process finished.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746bead6a0-d5e97c66-dedd-4b92-810e-c2e4840fafc9-000000@us-west-2.amazonses.com
In some devices difference in chip-id should be enough to pick
the right BDF. Add another support for chip-id based BDF selection.
With this new option, ath10k supports 2 fallback options.
The board name with chip-id as option looks as follows
board name 'bus=snoc,qmi-board-id=ff,qmi-chip-id=320'
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1
Tested-on: QCA6174 HW3.2 WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201207231824.v3.1.Ia6b95087ca566f77423f3802a78b946f7b593ff5@changeid
Kernel test robot reported warning:
drivers/net/wireless/mediatek/mt76/tx.c: In function
'mt76_txq_schedule':
>> drivers/net/wireless/mediatek/mt76/tx.c:499:21: warning: variable 'q'
>> set but not used [-Wunused-but-set-variable]
499 | struct mt76_queue *q;
| ^
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607542617-4005-1-git-send-email-jrdr.linux@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:123: warning: Function parameter or member 'dev' not described in 'iwl_acpi_get_dsm_object'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:123: warning: Function parameter or member 'rev' not described in 'iwl_acpi_get_dsm_object'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:123: warning: Function parameter or member 'func' not described in 'iwl_acpi_get_dsm_object'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:123: warning: Function parameter or member 'args' not described in 'iwl_acpi_get_dsm_object'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:142: warning: Function parameter or member 'dev' not described in 'iwl_acpi_get_dsm_u8'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:142: warning: Function parameter or member 'rev' not described in 'iwl_acpi_get_dsm_u8'
drivers/net/wireless/intel/iwlwifi/fw/acpi.c:142: warning: Function parameter or member 'func' not described in 'iwl_acpi_get_dsm_u8'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-17-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/fw/dbg.c:1932: warning: Function parameter or member 'reg_data' not described in 'iwl_dump_ini_mem'
drivers/net/wireless/intel/iwlwifi/fw/dbg.c:1932: warning: Excess function parameter 'reg' description in 'iwl_dump_ini_mem'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/iwl-phy-db.c:97: warning: Function parameter or member 'trans' not described in 'iwl_phy_db'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.c:340: warning: cannot understand function prototype: 'struct iwl_eeprom_enhanced_txpwr '
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:347: warning: Function parameter or member 'trans' not described in 'iwl_read_eeprom'
drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:347: warning: Function parameter or member 'eeprom' not described in 'iwl_read_eeprom'
drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:347: warning: Function parameter or member 'eeprom_size' not described in 'iwl_read_eeprom'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-8-lee.jones@linaro.org
Also add documentation for 'mvm'.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:400: warning: cannot understand function prototype: 'const u16 expected_tpt_legacy[IWL_RATE_COUNT] = '
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'mvm' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'tbl' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'scale_index' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'attempts' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'successes' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'window' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2677: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'mvm' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'lq_sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'band' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'mvm' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'lq_sta' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:4213: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_tx_protection'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-3-lee.jones@linaro.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/edd98d194bfc98b4be93a9bdc303630b719c0e66.1605896060.git.gustavoars@kernel.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly using the fallthrough pseudo-keyword as a
replacement for a number of "fall through" markings.
Notice that Clang doesn't recognize "fall through" comments as
implicit fall-through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117155904.GA14551@embeddedor
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly using the fallthrough pseudo-keyword as a
replacement for a number of "fall through" markings.
Notice that Clang doesn't recognize "fall through" comments as
implicit fall-through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117135053.GA13248@embeddedor
Added retry mechanism to ensure VMM enable bit is set during the
block transfer of data between host and WILC FW.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201208103739.28597-1-ajay.kathat@microchip.com
When waiting for a notification and then processing it,
we also need to check the size of the data before we use
it. Most places do that already, but fix the remaining
ones to do it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b29573bcba39.I4b7e72824d06dc0719a40021d933e29edfc14713@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification has several versions. Check the
notification size according to the expected notification version.
Notifications with incorrect size will be ignored.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.ee57c3214d05.I810d7de33fb08001ef1a2e24714d5b68932e088e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previously, we added checks that the contained MPDU size is long
enough, but really we should also check that the notification
itself fits into the data. Add some checks for that.
Also add unlikely() annotations on the previously added checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.51cc04cf1e3e.I7bfd6809f8f5feb75f79397646e6656e95688a0e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the channel switch delay that we would incur after the channel
switch actually happens is longer than the quiet time we're willing
to tolerate, disconnect as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.3bc3449922da.Ib0255deb67b2fc21317e274adcacb545bb1dc669@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some races in the hardware that can possibly lead to
a bus lockup later during a restart when we manage to kill the
firmware at a bad time (while it's accessing the bus).
To work around this, add support for a new handshake between
firmware and driver to ensure that the firmware is in a well-
known state before we kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a channel switch with a very long quiet period, we schedule
a work to disconnect after a while. This work runs in background. In the
meanwhile, we keep getting beacons and sending FW modify command for each.
This has a potential race, where we modify the CSA after we aborted it.
Protect the flow by setting csa_failed to true in case we abort, and check
it before sending the modify command.
This required a modification to the way we treat csa_failed in
iwl_mvm_post_channel_switch:
1. The variable isn't being reset anymore, so we can still look at it in
iwl_mvm_channel_switch_rx_beacon. This is fine, since we reset it when
starting a new CSA.
2. There is no more early return in case of csa_failed. This is fine,
since before this patch csa_failed was set only for GO, and for GO the
function is only resetting the power settings, which we want to restore
even in case of failure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b023856bdf39.I4ed0149e0018fe5e1ae3c2a1cbc614954016063f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We send some data to the firmware and expect to get it back,
but we shouldn't really trust the firmware on this. Check the
size of all the data we send down to avoid using bad or just
uninitialized data when the firmware doesn't respond right.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.a5a8173f16c7.I4fa68bb2b1c7dcc52ddd381c4042722d27c4a34d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the sequence/index/cmd_index unless we're doing
reclaim, they're not even valid in the other cases. Move the
variables and their assignments into the right if statement
and combine the two if statements into a single one as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.6207fdcc91a9.Ia71e766ead7560262f4bc6ad3da6f1117c498cd6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a bug in the lengths - the 'old length' needs to be calculated
using the 'old' pointer, of course, likely a copy/paste mistake. Fix
this.
Reported-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cf29c5b66b ("iwlwifi: dbg_ini: implement time point handling")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.c0105ddffa74.I1ddb243053ff763c91b663748b6a593ecc3b5634@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We set this here, but don't really use it until we've
enabled interrupts. But when enabling interrupts we
always overwrite this value anyway, so remove setting
it here, mostly in order not to have some additional
code duplicated later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.135d96297aca.Id2d26fff60b6c31202bb0a36e46948bda6a39d33@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is actually wrong, the bit used here by the image loader
is BIT(1), not BIT(2). The latter will be reused by the new
reset flow soon.
However, as we never had any complaints about not printing
the IML status or not handling the IML error interrupt (and
I suspect the code handling it was incorrectly anyway) just
remove the code for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.9a323f4a3493.Ic7aee4dbbf4be42287c338c2fa1b111473724116@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We keep the scan status per UID in scan_uid_status field when the
iwl_mvm_build_scan_cmd() function is called. If we error out after
this, e.g. due to FW restart being in progress, we're not cleaning
up properly, and can run into warnings later.
Clean up internal variables when starting fails after calling the
iwl_mvm_build_scan_cmd() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.970421a2f753.Id62b2da8a0ccccbb114407db82ca485d07749d39@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're currently doing accounting on the queue sync with an
atomic variable that counts down the number of remaining
notifications that we still need.
As we've been hitting issues in this area, modify this to
track a bitmap of queues, not just the number of queues,
and print out the remaining bitmap in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.0a3fa177cd6b.I7c69ff999419368266279ec27dd618eb450908b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For triggering an NMI in the firmware, we should only set BIT(24)
in the corresponding register, not the entire mask that's usable
by the driver.
This currently doesn't matter because the firmware only enables
BIT(24), but we'll start using BIT(25) for other purposes with an
upcoming API change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.2f982365d085.Id09daabfd331ba9e120abcbbedd2ad6448902ed0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If 12k A-MSDU size is requested, we will actually allocate 16k
due to page allocation. Thus, change it to actually mean 16k,
which is useful for certain sniffer use cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.84ae405829d4.I31184f4be31f7c3feb9a29aef3a111e70d15c64a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MPDU contained in a notification shouldn't be larger than the
notification size itself is, validate this.
Reported-by: Haggai Abramovsky <haggai.abramovsky@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7c721ad37014.Id5746874ecfa208b60baa62691b2d9dc5dd4d89c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Similarly to what I did to iwl_run_init_mvm_ucode, there is no
need to pass the read_nvm parameter. Either we have an NVM
and we don't need to read it, or we don't and we need to read it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.1b764faecfee.I2da0ada577fc16268125a4a15b5e725c18c643ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Curretly we only mark HW error state "after" trying to collect HW data,
but if any HW error happens while colleting HW data we go into endless
loop. avoid this by setting HW error state "before" collecting HW data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4c7e5a87da15.Ic35b2f28ff08f7ac23143c80f224d52eb97a0454@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to the 6GHz band (aka. Ultra High Band or UHB). This
allows us to scan and connect to channels in that band, including all
the relevant features, such as preferred scan channels, colocated
channels etc.
Co-developed-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Co-developed-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Co-developed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Co-developed-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Signed-off-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201210000657.0fdbfc3d7352.Idb648536faf21716e2ab2c6d6890d3e49f719cd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This data is not necessarily the same across devices as we may
modify it due to the number of antennas and for overrides (though
in practice overrides are likely to be identical), so modifying
the global data is wrong.
Make a copy of it in the NVM data and modify it there instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.6b4ee30c59e4.I0c30ef78b3bf727fe80b16a19c7588016d6b04bf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer need code that was introduced to differentiate
between two early versions of 8260.
We can remove this convoluted way to get the hardware version
that was needed because of a bug in the register's
configuration.
Moreover, since we no longer need to access the PRPH
registers, we no longer need to wake up the device,
request ownership, etc...
Remove all that.
This allows us to get the rid of the obsolete comment
about the AUX bus MISC address space which should have
been moved when this code was moved away from here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4a5665ccd8a6.Iff3879405c15758ba661c430e77dc2160ddada1c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This command should be used only when there's a real client station.
Currently it works, but since soon the driver will stop actually having
an auxiliary station by default, and this command requires _some_ valid
station, it needs to be removed from this flow.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.81b2acfe292b.I8c7372e6f72279e22966a2d0a9066521f9d2f1a0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ofdm_index[] is used to indicate how many power compensation is needed to
current thermal value. For internal PA module or 2.4G band, the min_index
is different from other cases.
This issue originally is reported by Dan. He found the size of ofdm_index[]
is 2, but access index 'i' may be equal to 2 if 'rf' is 2 in case of
'is2t'.
In fact, the chunk of code is added to wrong place, so move it back to
proper place, and then power compensation and buffer overflow are fixed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201207031903.7599-1-pkshih@realtek.com
Assure that frames with the fixed order flag are not reordered
relative to each other. This is accomplished by transmitting them
using a fixed priority independent of their QoS field.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104061823.197407-6-Mathy.Vanhoef@kuleuven.be
Currently 256 bitmap in blockack frames is being set only for AP mode.
Fix this to set whenever beacon has changed and has HE capability, there
by supporting mesh as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-5-pradeepc@codeaurora.org
HE operation IE in beacons is constructed based on userspace params,
which firmware might not be aware of. This causes firmware not to
configure TXOP duration based RTS threshold which could cause mismatch
in behaviour with respect to what is being advertised in beacons. This
patch sends HE operation IE fetched from beacon to firmware using
WMI interface for configuration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-4-pradeepc@codeaurora.org
These error paths need to drop the &ar->conf_mutex before returning.
Fixes: 690ace20ff ("ath11k: peer delete synchronization with firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X85sVGVP/0XvlrEJ@mwanda
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f932c887e013767cbdabfdddd671086e8ae63193.1605896060.git.gustavoars@kernel.org
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* Fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* Fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/52931e343af25f6dab4bd1d604889d2594a861dd.1605896060.git.gustavoars@kernel.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/967a171da3db43e4cdf38104876b4ec1cde46359.1605896060.git.gustavoars@kernel.org
I am trying to get the ath11k driver to work with VyOS and during the
build it tries to discover the firmware blobs which drivers require.
This doesn't work with ath11k because it doesn't use the MODULE_FIRMWARE
macro. This patch fixes that.
Signed-off-by: Devin Bayer <dev@doubly.so>
[kvalo@codeaurora.org: cleanup commit log, move to pci.c]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201202182705.dhkml4nb4rf2vwav@orac
When 8822CE is associating with AP, driver will poll status bit of
IQ calibration to confirm the IQ calibration is done, and then move on
the association process. Current polling time for IQ calibration is 6
seconds.
But occasionally driver fails in polling the status bit because the status
bit is not set after IQ calibration is done. When it happends, association
process will be serieously delayed up to 6 seconds. To avoid it, we reduce
polling time to 300ms, in which the IQ calibration can be done.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201208014503.12118-1-pkshih@realtek.com
'const struct dev_pm_ops rtw_pm_ops' is declared by pci.c, and it should be
declare as 'extern' in pci.h. Without 'extern' causes every file including
pci.h has an individual instance of rtw_pm_ops but not reference to the one
declared in pci.c
If kernel config, like test robot, doesn't build driver as module, it leads
multiple definition.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 2e86ef413a ("rtw88: pci: Add prototypes for .probe, .remove and .shutdown")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201208013746.11065-1-pkshih@realtek.com
mwifiex_cmd_802_11_ad_hoc_start() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Zhang Xiaohui <ruc_zhangxiaohui@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201206084801.26479-1-ruc_zhangxiaohui@163.com
The pointer 'entry' is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201204180459.1148257-1-colin.king@canonical.com
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: cc0b88cf5e ("[PATCH] Add adm8211 802.11b wireless driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607071638-33619-1-git-send-email-zhangchangzhong@huawei.com
When driver was developed, FCC regulation didn't enable channel 144
and there was no demand for channel 144 at that time. Although HW
actually supports channel 144, driver didn't announce channel 144.
Therefore, channel 144 (20 MHz), channel 142 (40 MHz) and channel
138 (80 MHz) couldn't be used.
Today, channel 144 has been enabled by regulations and
is gradually being supported. With test requirements,
we declare hw supports channel 144.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201204013823.3729-1-pkshih@realtek.com
Currently the variable 'interval' is not initialized and is only set
to 1 when oex_stat->bt_418_hid_existi is true. Fix this by inintializing
variable interval to 0 (which I'm assuming is the intended default).
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: 5b2e9a35e4 ("rtw88: coex: add feature to enhance HID coexistence performance")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203175142.1071738-1-colin.king@canonical.com
The assignment to pointer vif is redundant as the assigned value
is never read, hence it can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203174316.1071446-1-colin.king@canonical.com
As of 6-DEC-2019, NXP has acquired Marvell’s Wireless business
unit. This change is to update the license text accordingly.
commit 932183aa35 ("mwifiex: change license text from MARVELL
to NXP") does this, but it left out two files.
Signed-off-by: James Cao <zheng.cao@nxp.com>
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606814307-32715-1-git-send-email-ganapathi.bhat@nxp.com
Also strip out other duplicates from driver specific headers.
Ensure 'main.h' is explicitly included in 'pci.h' since the latter
uses some defines from the former. It avoids issues like:
from drivers/net/wireless/realtek/rtw88/rtw8822be.c:5:
drivers/net/wireless/realtek/rtw88/pci.h:209:28: error: ‘RTK_MAX_TX_QUEUE_NUM’ undeclared here (not in a function); did you mean ‘RTK_MAX_RX_DESC_NUM’?
209 | DECLARE_BITMAP(tx_queued, RTK_MAX_TX_QUEUE_NUM);
| ^~~~~~~~~~~~~~~~~~~~
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtw88/pci.c:1488:5: warning: no previous prototype for ‘rtw_pci_probe’ [-Wmissing-prototypes]
1488 | int rtw_pci_probe(struct pci_dev *pdev,
| ^~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1568:6: warning: no previous prototype for ‘rtw_pci_remove’ [-Wmissing-prototypes]
1568 | void rtw_pci_remove(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1590:6: warning: no previous prototype for ‘rtw_pci_shutdown’ [-Wmissing-prototypes]
1590 | void rtw_pci_shutdown(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~~~
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-18-lee.jones@linaro.org
Incase of hardware encryption, WMI_PEER_AUTH flag will be set by firmware
during install key. Since install key wont be done for software encryption
mode, firmware will not set this flag. Due to this, seeing traffic failure
in software encryption. Hence, avoid resetting peer auth flag if hardware
encryption disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606369414-25211-1-git-send-email-seevalam@codeaurora.org
In QCN9074 ath11k boot, firmware crash is observed in 64-bit
builds and is due to wrong 64 bit MSI address size. This patch
fixes the firmware crash. Read msi high addr if 64-bit addresses
allowed on MSI.
Tested-On: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606199334-18206-1-git-send-email-akolli@codeaurora.org
cppcheck possible warnings: (new ones prefixed by >>, may not real problems)
drivers/net/wireless/ath/ath10k/sdio.c:2234:2:
warning: Non-boolean value returned from function returning bool [returnNonBoolInBooleanFunction]
return param & HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW;
Reported-by: kernel test robot <rong.a.chen@intel.com>
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606103240-9868-1-git-send-email-wgong@codeaurora.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mcs value of HT mode reported by mt7915_mcu_get_rx_rate()
has already been converted to the expected format.
Tested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of stopping and waking only a single queue, handle all phy tx queues
mapped ot the same hardware queue.
Also allow the driver to block tx queues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915 automatically detects dbdc feature so drop debugfs knob.
Move if_comb, mt7915_rates, if_limits structs and mt7915_regd_notifier(),
mt7915_init_wiphy() routines at the begging of init.c in order to make
mt7915_register_ext_phy routine static
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7915 dbdc support. If dbdc is available, mt7915 primary phy
will work on 2.4GHz band, while secondary one on 5GHz band.
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce dbdc support to mt7915 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move properly support mt7915 dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_init_mcu_queue utility routine in order to allocate
dedicate q_mcu pointers for mcu hw queues. This is a preliminary patch
to move data queues in mt76_phy and add dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move hw data queues in mt76_phy for
mt7915 dbdc support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_init_tx_queue in mac80211.c since it is shared by all
drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to make the code more readable, rely on mt7915_eeprom_field
definitions for eeprom parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since wtbl workqueue is used only for rate handling, refactor code to
make it more clear
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY.
Note that two PHYs share global 32 omac slots with each other.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7915_mcu_bss_sync_tlv() is no longer used, so remove it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The omac_idx variable is u64 so we should use the 64-bit BIT_ULL().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make mt7915_eeprom_read routine static since it is used only in eeprom.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support to set tx frequency offset in testmode, which is usally used in
the pre-calibration stage.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support tx_power setting in testmode. Note that the tx power value of
antenna 1-3 equal to antenna 0.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support testmode rx and display rx statistic by parsing RXV packet
type, which is currently only enabled in testmode.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support testmode tx for MT7915A, including tx streams and HE rate
settings.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend enum mt76_testmode_tx_mode to support various HE rate modes.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Correct the bitfields of tx rateval and bw in tx descriptor.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prepare for setting different LTF (1x, 2x, and 4x) and GI (0.8us,
1.6us, 3.2us) combinations in HE rate mode.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add the parameter to control STBC function in testmode.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support to display snr value when dumping rx statistics.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Change ib_rssi and wb_rssi into array type, since they could be reported
by per-antenna.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Split tx and status path in mt76-usb module relying on mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve parallelism, convert rx path in mt76-usb module to
mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since rate configuration is run holding dev mutex, we can run key
configuration in mt7615_set_key for usb/sdio devices avoiding to
schedule the workqueue
Tested-by: Tested-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch to wep sw crypto for mt7615/mt7915 since wtbl require a sta
reference and wep key is not pairwise
Tested-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
SDIO-based WiFi would rely on an additional GPIO pin to wake up the host.
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_send_firmware routine in common code since it is actually
shared between mt7615, mt7663, mt7603 and mt7915 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some newer MT7628 based routers (notably the TP-Link Archer C50 v4) are
shipped with a chip-id of 0x7600 in the on-flash EEPROM. Add this as a
possible valid ID.
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2781
Suggested-by: Ron Asimi <ron.asimi@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76_free_device instead of ieee80211_free_hw if device probing
fails in order to remove the already allocated mt76 workqueue
Fixes: a86f1d01f5 ("mt76: move mt76 workqueue in common code")
Fixes: f1d962369d ("mt76: mt7915: implement HE per-rate tx power support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If THIS_MODULE is not set, the module would be removed while debugfs is
being used.
It eventually makes kernel panic.
Fixes: ec9742a8f3 ("mt76: mt7915: add .sta_add_debugfs support")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
sched quota is now updated in mt7663s_txrx_worker so there is no more
need of sched.lock mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Properly account current consumed ple quota in mt7663s_tx_pick_quota
routine and avoid possible underflow.
Fixes: 6ef2d665f6 ("mt76: mt7663s: split mt7663s_tx_update_sched in mt7663s_tx_{pick,update}_quota")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of mt7663s_sta_add routine and rely on mt7615_mac_sta_add
since sched quota is already initialized in mt7663s_mcu_init_sched
routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add sched_quota debugfs node for mt7663s. Scheduling quota stats
are useful for debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce cpu cycles, enable hw beacon filter by default if
the device is running offload fw with sta only interfaces.
Disable runtime pm for multi-vif scenario.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It was accidentally dropped while adding multiple wiphy support
Fixes fast-rx support and avoids handling reordering in both mac80211
and the driver
Cc: stable@vger.kernel.org
Fixes: c89d362541 ("mt76: add function for allocating an extra wiphy")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When per-packet rate reporting is enabled, the hardware can get stuck under
some conditions. It self-recovers quickly, but in practice this leads to
reduced performance.
In order to avoid running into this issue, disable per-packet rate reporting
by default and query the rx rate from firmware instead, unless monitor mode
is enabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Can be used by the caller to get the response data directly instead of using the
hack of storing the result in internal data structures from .mcu_parse_response
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware/hardware supports only 16 entries. Trying to use more can lead
to timeouts on some firmware versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the MT7915 info, the fields for the WLAN index / queue overlap with the
token id, and the MT_TX_FREE_PAIR bit indicates, which one is present.
If MT_TX_FREE_PAIR is set, skip processing the token index, since the data
will not be valid.
This fixes accidentally freeing tokens which are still in use by the
hardware with a wrong station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When looking for a MAC address slot, start by using main BSSID slots 1-3,
afterwards use 16 repeater mode BSSID slots, then start using the slots
usually used for AP mode.
This search order should prevent unnecessary conflicts with AP mode interfaces
on the same PHY
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer chipsets can deal with the same STA on multiple interfaces
Preparation for supporting more station interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is primarily for testing and can be used in combination with monitor
mode to make the card respond to packets sent to a specific MAC address.
For now this is only exposed as a debug/testing feature, later on the
approach might be used to support more concurrent station interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert status_work and net_work
to mt76 worker APIs.
Remove txrx_wq sdio workqueue since it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce sdio bus contention, disable interrupts during
txrx_worker processing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert txrx_work to mt76 worker
threads APIs.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7663 tx and rx processing in the same workqueue in order to
reduce jitter that can hit tcp performances. This is a preliminary patch
to switch to mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_load_patch in mt7615/mcu.c sometimes fails with:
mt7622-wmac 18000000.wmac: Failed to get patch semaphore
and returns -EAGAIN. But this error is returned all the way up to
mt7615_init_work with no actual retrial performed, leaving a
broken wireless phy.
Wait a bit and retry for up to 10 times before giving up.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MCU field should contain a boolean 0/1, not the flag itself.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Read per-stream measurements every 100 ms and build a simple moving average.
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This code does not ensure that the whole buffer is initialized and none
of the callers check for errors so potentially none of the buffer is
initialized. Add a memset to eliminate this bug.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda
ath.git patches for v5.11. Major changes:
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
The macro use will already have a semicolon.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201127175821.2756988-1-trix@redhat.com
Added multiple queues[BK,BE,VI,VO] to handle different priority data
packets. Before adding a packet to the queue, checked its priority from
the header, and then add to the suitable queue. The limit for each queue
is maintained separately. Also while passing the packets to the firmware
via VMM take care to select data packets based on priority and available
space.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-6-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_mgmt_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure case.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-4-ajay.kathat@microchip.com
Before returing from wilc_wlan_txq_add_net_pkt() invoke tx_complete_fn()
callback to free up allocated memory for failure cases.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201125114059.10006-3-ajay.kathat@microchip.com
Apart from a firmware binary the chip needs a config file used by the
FW. Add the config files to modinfo so that they can be read by
userspace.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201124120018.31358-1-matthias.bgg@kernel.org
Add toggle table related function to enhance WL throughput when WL coexist
with 4/18 HID.
The toggle table feature will toggle WL/BT priority table during WL slot,
it can decrease the impact from HID's frequently packets and prevent HID
lag.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-11-pkshih@realtek.com
Add modifications for A2DP interoperability issue of TWS earphones.
Some TWS earphones has low buffer size, so it's necessary to reduce
the slot period to let it get data more frequently.
(e.g. use 4-slot to replace the original 2-slot method).
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-10-pkshih@realtek.com
The original setting misses some necessary configuration.
Make coexistence slot align to beacon and check the connection situation
to know if we need to extend WLAN slot or not.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-9-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
Add a flag to make decision whether the mechanism
should go into free-run mode or not.
For now, it is always false, the flag assignment will
be implemented later.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-7-pkshih@realtek.com
Add TDMA slot type setting for later usage.
Since the transmission of HID profile is very frequently,
it may bring a big impact to WLAN performance.
To change slot type, it can make mechanism be more flexible.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-6-pkshih@realtek.com
In free run mode, this WLAN info updating is only related to AFH
information, not related to the connection state, which is the current
implementation.
Always update WLAN info in free run mode now.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-5-pkshih@realtek.com
Update A2DP+PAN+WL mechanism for CPT(Coexistence Performance Test) to
enhance WL/BT performance at the environment that some specific AP are
existing.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-4-pkshih@realtek.com
Add message for debugging usage and the program flow is no change.
Add a variable reserved for WLAN firmware synchronize.
Add a group of variable to save BT packet counter, it will be
assigned as mechanism judgment in the future. Now it is just for
debug usage.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-3-pkshih@realtek.com
When WLAN entering or leaving, it's necessary to run coexistence mechanism
to ensure the setting matched current status.
Without calling rtw_coex_run_coex(), WLAN poor throughput or bad A2DP
quality may happen.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-2-pkshih@realtek.com
This reverts commit 2860615076.
Since actually Buffalo WI-U3-866D is falied to power on with the change.
The rtl8812au driver code to power on is same with the rtl8821a code.
But the rtl8821ae included rtl8821a does not support USB interface.
So seems that rtl8812au should be supported by rt1l8821a code with USB.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201121003411.9450-1-ikegami.t@gmail.com
The NO_160 flag specifies if the device doesn't have 160 MHz support,
but we errorneously assumed the opposite. If the flag was set, we
were considering that 160 MHz was supported, but it's actually the
opposite. Fix it by inverting the bits, i.e. NO_160 is 0x1 and 160
is 0x0.
Fixes: d6f2134a38 ("iwlwifi: add mac/rf types and 160MHz to the device tables")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201202143859.375bec857ccb.I83884286b688965293e9810381808039bd7eedae@changeid
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
qmi_msg_handler[] and ath10k_qmi_ops are only used as input arguments
to qmi_handle_init() which accepts const pointers to both qmi_ops and
qmi_msg_handler. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122234031.33432-3-rikard.falkeborn@gmail.com
Should an error occur after calling 'ath10k_usb_create()', it should be
undone by a corresponding 'ath10k_usb_destroy()' call
Fixes: 4db66499df ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170358.1346065-1-christophe.jaillet@wanadoo.fr
If 'ath10k_usb_create()' fails, we should release some resources and report
an error instead of silently continuing.
Fixes: 4db66499df ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170342.1346011-1-christophe.jaillet@wanadoo.fr
The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.
Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71
The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1
Fixes: cea19a6ce8 ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org
If 'kzalloc' fails, we must return an error code.
While at it, remove a useless initialization of 'err' which could hide the
issue.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122173943.1366167-1-christophe.jaillet@wanadoo.fr
It is rather easy to add more entries to ath11k_skb_cb while forgetting the
size limit of ieee80211_tx_info->driver_data. So just check this during the
build to reduce the change of accidental buffer overflow in the skbuff->cb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-3-sven@narfation.org
It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):
[ 86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
[ 86.963192] pgd = ffffffc0008f0000
[ 86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
[ 86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[...]
[ 87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
[ 87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
[ 87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
[ 87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
[ 87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
[ 87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
[ 87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
[ 87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
[ 87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
[ 87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)
Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
(162 patches at the moment which are often not upstreamed but essential
to get ath11k working)
Fixes: e7f33e0c52 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unused structure ath11k_vdev_stop_status is removed.
'ath11k_mac_get_ar_vdev_stop_status' api has been replaced
with 'ath11k_mac_get_ar_by_vdev_id' inside vdev_stopped_event.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-4-git-send-email-mkenna@codeaurora.org
Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org
When the interface is added immediately after removing the
interface, vdev deletion in firmware might not have been
completed.
Hence, add vdev_delete_resp_event and wait_event_timeout
to synchronize with firmware.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-2-git-send-email-mkenna@codeaurora.org
Add the missing destroy_workqueue() before return from
cw1200_init_common in the error handling case.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119070842.1011-1-miaoqinglang@huawei.com
In rtl8723e_tx_fill_cmddesc(), skb->data is mapped to streaming DMA on
line 531:
dma_addr_t mapping = dma_map_single(..., skb->data, ...);
On line 534, skb->data is assigned to hdr after cast:
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
Then hdr->frame_control is accessed on line 535:
__le16 fc = hdr->frame_control;
This DMA access may cause data inconsistency between CPU and hardwre.
To fix this bug, hdr->frame_control is accessed before the DMA mapping.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119015218.12220-1-baijiaju1990@gmail.com
In rtl92de_tx_fill_cmddesc(), skb->data is mapped to streaming DMA on
line 667:
dma_addr_t mapping = dma_map_single(..., skb->data, ...);
On line 669, skb->data is assigned to hdr after cast:
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
Then hdr->frame_control is accessed on line 670:
__le16 fc = hdr->frame_control;
This DMA access may cause data inconsistency between CPU and hardwre.
To fix this bug, hdr->frame_control is accessed before the DMA mapping.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119015205.12162-1-baijiaju1990@gmail.com
In rtl92ce_tx_fill_cmddesc(), skb->data is mapped to streaming DMA on
line 530:
dma_addr_t mapping = dma_map_single(..., skb->data, ...);
On line 533, skb->data is assigned to hdr after cast:
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
Then hdr->frame_control is accessed on line 534:
__le16 fc = hdr->frame_control;
This DMA access may cause data inconsistency between CPU and hardwre.
To fix this bug, hdr->frame_control is accessed before the DMA mapping.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119015151.12110-1-baijiaju1990@gmail.com
In rtl88ee_tx_fill_cmddesc(), skb->data is mapped to streaming DMA on
line 677:
dma_addr_t mapping = dma_map_single(..., skb->data, ...);
On line 680, skb->data is assigned to hdr after cast:
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
Then hdr->frame_control is accessed on line 681:
__le16 fc = hdr->frame_control;
This DMA access may cause data inconsistency between CPU and hardwre.
To fix this bug, hdr->frame_control is accessed before the DMA mapping.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119015127.12033-1-baijiaju1990@gmail.com
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117160958.GA18807@embeddedor
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 17ff2c794f ("rsi: reset device changes for 9116")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605582454-39649-1-git-send-email-zhangchangzhong@huawei.com
The left-hand side of the assignment from cpu_to_le32() should be of
type __le32. This commit clears the warning reported by sparse when
building with C=1 CF="-D__CHECK_ENDIAN__".
Fixes: d56fd83cf9 ("brcmfmac: fix SDIO access for big-endian host")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Remi Depommier <rde@setrix.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201116001639.31958-1-rde@setrix.com
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: b7da53cd6c ("qtnfmac_pcie: use single PCIe driver for all platforms")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201114123347.29632-1-wanghai38@huawei.com
The variable u4tmp is overwritten by the following call and the assignment
is useless, so remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605332735-9648-1-git-send-email-kaixuxia@tencent.com
ezusb_read_ltv() is always invoked via the ->read_ltv() callback. This
callback is mostly invoked under orinoco_lock() which disables BH.
There are a few invocations during probe which occur in preemptible
context via:
ezusb_probe() -> orinoco_init() -> determine_fw_capabilities()
Extend `hermes_ops' with the ->read_ltv_pr callback which is implemented
with the same callback like ->read_ltv on `hermes_ops_local'.
On `ezusb_ops' ->read_ltv is used for callbacks under the lock which
need to poll.
The new ->read_ltv_pr() is used in the preemptible context in which it
is possible to wait for the completion. Provide HERMES_READ_RECORD_PR()
and hermes_read_wordrec_pr() which behave like their non _pr equivalents
and invoke ->read_ltv_pr().
This removes the last user of ezusb_req_ctx_wait() and can now be
removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-11-bigeasy@linutronix.de
All invocations of ezusb_docmd_wait() happen via ->cmd_wait(). This
callback is always invoked under the orinoco_lock() which disables BH.
Use ezusb_req_ctx_wait_poll() for ezusb_docmd_wait() because it must not
sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-10-bigeasy@linutronix.de
ezusb_doicmd_wait() is invoked via ->init_cmd_wait() callback.
This callback is only invoked hermesi_program_init() and
hermesi_program_end() which are the ->program_init() and ->program_end()
callbacks as assigned by `hermes_ops_local'. They are never used by the
USB interface since the USB interface provides its own set of callbacks
by `ezusb_ops'.
Replace ezusb_doicmd_wait() with a warning in case I missed the obvious.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-9-bigeasy@linutronix.de
All invocation of ezusb_write_ltv() happen via ->write_ltv() and are
performed under the orinoco_lock() which disables BH.
Use ezusb_req_ctx_wait_poll() for ezusb_write_ltv() because it must not
sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-8-bigeasy@linutronix.de
ezusb_read_pda() is invoked via ->read_pda() while firmware is loaded in
preemtible context.
Use ezusb_req_ctx_wait_compl() in ezusb_read_pda().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-7-bigeasy@linutronix.de
The ezusb_program() is invoked via ->program() in preemptible
context during firmware loading. This is also true for the
->program_init() and ->program_end() callback.
Use ezusb_req_ctx_wait_compl() in ezusb_program_init(),
ezusb_program_bytes(), ezusb_program_end() which are part of firmware
loading during device probe.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-6-bigeasy@linutronix.de
ezusb_init() is always invoked in preemptible context during device
probe. Only orinoco_up() -> orinoco_reinit_firmware() may invoke the
function from atomic context but this is never used for the USB
interface.
Use ezusb_req_ctx_wait_compl() for the ezusb_write_ltv() and
ezusb_docmd_wait() invocations from within ezusb_init().
Preserve the generic versions which have still other user via the
callback.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-5-bigeasy@linutronix.de
ezusb_xmit() sets ->in_rid in its request which means it does not wait
for an answer.
Use the ezusb_req_ctx_wait_skip() to denote that an answer is not
expected.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-4-bigeasy@linutronix.de
ezusb_access_ltv() sends the prepared request to the USB device.
Requests which have ->in_rid set expect an answer from the USB device
and the function has to wait until the URB with the answer arrives.
The function uses in_interrupt() to determine if it can simply sleep on
the completion and be woken up once the answer arrives or if it needs to
poll on the completion.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Aside of that in_interrupt() is not correct as it does not catch preempt
disabled regions in which sleeping is also not allowed.
Provide stubs which can be used as a replacement. The current default is
the current behaviour which sleeps/polls depending on in_interrupt().
The goal is to audit all callers and use either the poll or sleep
version.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-3-bigeasy@linutronix.de
ezusb_xmit() allocates a context which is leaked if
orinoco_process_xmit_skb() returns an error.
Move ezusb_alloc_ctx() after the invocation of
orinoco_process_xmit_skb() because the context is not needed so early.
ezusb_access_ltv() will cleanup the context in case of an error.
Fixes: bac6fafd4d ("orinoco: refactor xmit path")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201113212252.2243570-2-bigeasy@linutronix.de
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605248896-16812-1-git-send-email-zhangchangzhong@huawei.com
Fix sometimes FW information will be parsed as wrong value,
do a correction of sign bit to show the correct information.
(Ex, Value should be 20, but it shows 236.)
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-12-pkshih@realtek.com
Remove extend 5 ms related operation at WLAN media status notify.
The mechanism should be enable only while DUT connect to a AP that it
doesn't follow our power save control or its rate is decreasing unusually
sensitive. So we extend a extra slot to save the transmission rate.
The original logic will always extend WLAN slot.
It will lead to BT slot always decrease 5 ms.
Remove write scoreboard action at WLAN media status notify.
It has already done in WLAN info notify.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-11-pkshih@realtek.com
Remove some action which were writing scan bit to scoreboard,
since these behaviors are redundant.
It is already done in WLAN info notify.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-10-pkshih@realtek.com
Force set the coexistence to BT high priority during
WLAN initial/power-on step. Since the duration the related setting
may be not ready yet.
The score board is not related to scan when initialing, remove the scan
parameter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-9-pkshih@realtek.com
While the mechanism goes to 2G_free_run or WL5G_BT2G,
set BT to hardware PTA mode to get a more efficiently performance.
Add a flag to indicate antenna switch is supported or not so
that the IC serials which has different antenna structure can
set antenna correctly.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-8-pkshih@realtek.com
The updated parameter and original parameter all means TDMA-OFF.
The original setting write 0x8 to firmware, but it only works for
some old IC series.
To avoid the confusing, update a proper parameter.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-7-pkshih@realtek.com
Add the related coexistence mechanism about RF4CE and WLAN connected
flag to decide control packet is whether higher or normal priority.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-6-pkshih@realtek.com
Because sometimes hardware action may be unpredictable.
(Ex: after WLAN LPS...etc)
Add a check mechanism if the action is triggered by
some concerned case, it can force to write the table again.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-5-pkshih@realtek.com
When WLAN in critical procedure, such as connecting, scan and so on,
coexistence will notify BT by scoreboard.
While BT firmware received the scoreboard interrupt, it will adjust
BT page priority lower to avoid WLAN critical procedure suffering impact.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-4-pkshih@realtek.com
Because the WLAN RSSI report feature had been implemented at WLAN link info
update function, it is redundant to update WLAN RSSI while BT is updating
link info, so remove the update WLAN RSSI part.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-3-pkshih@realtek.com
Add considering for different WLAN beacon interval in coexistence
mechanism.
Because the WLAN beacon period may be not 100 ms, so it's necessary
to consider any beacon period and set timer according to the interval.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-2-pkshih@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8723d.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109090123.9254-1-pkshih@realtek.com
Set the rx_filter in ath11k_mac_config_mon_status_default(),
only when the rx_filter value exists in ath11k_debug_rx_filter().
Without this change, rx_filter gets set to 0 and peer rssi stats
aren't updating properly from firmware.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01230-QCAHKSWPL_SILICONZ-4
Fixes: ec48d28ba2 ("ath11k: Fix rx_filter flags setting for per peer rx_stats")
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605091117-11005-1-git-send-email-mkenna@codeaurora.org
This target IRAM recovery feature support is to copy target
IRAM contents available at ATH10K_MEM_REGION_TYPE_REG to host
memory for back up after firmware loaded. Target IRAM contents
are copied to wmi memory chunks allocated for the
WMI_IRAM_RECOVERY_HOST_MEM_REQ_ID and provide the wmi chunks
address to the firmware through wmi init command.
If firmware detects andy IRAM corruption through periodic
checksum validation, It will download the IRAM contents back
from the provided wmi memory chunks address using hif_memcpy.
This IRAM recovery feature prevent target assert in case of
unexpected target IRAM corruptions.
This patch also introduce a new feature flag 'iram-recovery' for
backward compatibility.
Tested-on: QCA9888 10.4-3.9.0.2-00094
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604657442-23674-1-git-send-email-vnaralas@codeaurora.org
STS Beamformee capability sent from firmware is overwritten as
num_tx_chains - 1.
When num_tx_chains is 2, then STS is set to invalid value 1.
Since STS is not limited by number of TX chain, not overwriting the
capability received from firmware.
Tested on: IPQ6018 WLAN.HK.2.4.0.1-00303-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <rgnanase@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604933229-15815-1-git-send-email-rgnanase@codeaurora.org
Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.
Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.
Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org
There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.
This is really up to the MHI device(channel) driver to manage the state
of its channels.
While at it, let's also remove the auto-start option from ath11k mhi
controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
-----BEGIN PGP SIGNATURE-----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=TGgF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace usbnet_get_stats64() with new identical core function
dev_get_tstats64() in all users and remove usbnet_get_stats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of qtnf_vif for storing a pointer
to the per-cpu counters. This allows us to use core functionality for
statistics handling.
The driver sets netdev->needs_free_netdev, therefore freeing the per-cpu
counters at the right point in time is a little bit tricky. Best option
seems to be to use the ndo_init/ndo_uninit callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Life time related setting is related to WLAN active port number,
not its mode. The original setting may cause poor WLAN performance.
In most case, WLAN TX limitation is helpful for BT in coexistence
scenario, especially for A2DP quality.
So this is necessary to fix the setting and constraint it.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-12-pkshih@realtek.com
Since coexistence issue is related to WL/BT and each digital/analog/rf,
and these issues are often critical with low failure rate, add more
debugging information is helpful to clarify issues.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-11-pkshih@realtek.com
Adaptive Frequency Hopping(AFH) is a method of transmitting
radio signals by rapidly changing the carrier frequency among
many distinct frequencies, which can avoid interference.
Add this feature to update AFH parameter for 8822b.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-10-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Add counter to count BT info C2H command for debug usage.
It could present the C2H channel situation.
Fix BT IQK state decision condition for counting.
The original condition is wrong, it would cause coexistence mechanism
going to the wrong strategy.
New format supports getting TDMA parameter from WL firmware, since
coexistence needs current TDMA parameter to decide strategy.
Remove unnecessary operations about scoreboard, it is not a must for
current version.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-8-pkshih@realtek.com
The original stop_dm flag is shared with the wifi and coexistence
mechanism internal usage, which represent two meanings, and makes
developers hard to debug.
Add a new flag manual_control for coexistence mechanism usage only.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-7-pkshih@realtek.com
To make sure the related ANT/RF_PARA setting will be expected result in COEX.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-6-pkshih@realtek.com
Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com
Use macro definition to replace magic number.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-4-pkshih@realtek.com
Update COEX parameters and logic to enhance WL/BT performance
while WL_Busy + A2DP in a less interference environment.
It can avoid the interference comes cross from each other
and earned more performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-3-pkshih@realtek.com
Some register definition and bit definition were incorrect.
e.g. REG_BT_COEX_V2 should be word alignment to meet the coding style.
e.g. set REG_BT_TDMA_TIME[5:0]=0x5,
But the original is to set REG_BT_TDMA_TIME[7:0]=0x5.
This will cause unexpected hardware behavior.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-2-pkshih@realtek.com
The inner do { ... } while loop is completely useless, all it does
is iterate over a switch-case statement, one bit at a time. This
can easily be replaced by simple if (status & bit) { ... } tests
for each bit. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-2-marex@denx.de
The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.
The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."
The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.
This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.
Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
The functions mwifiex_shutdown_sw() and mwifiex_reinit_sw() can be used
for more general purposes than the PCIe function level reset. Also, these
are even not PCIe-specific.
So, let's update the comments at the top of each function accordingly.
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142110.18144-3-kitakar@gmail.com
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Detect and avoid this endless loop.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
On some platforms, the preset values aren't correct and then we may
get a completion timeout in the firmware. Change the LTR configuration
to avoid that. The firmware will do some more complex reinit of this
later, but for the boot process we use ~250usec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d83d591c05ba.I42885c9fb500bc08b9a4c07c4ff3d436cc7a3c84@changeid
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
We need to feed the configuration id to remove session protection
properly.
Remember the conf_id when we add the session protection so that we
can give it back when we want to remove the session protection.
While at it, slightly improve the kernel doc for the conf_id
of the notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.3642f730333d.I01a98ecde62096d00d171cf34ad775bf80cb0277@changeid
The ROC that runs on the AUX ROC (meaning an ROC on the STA vif),
was added with the HOT_SPOT_CMD firmware command and must be
cancelled with that same command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.a317376154da.I44fa3637373ba4bd421cdff2cabc761bffc0735f@changeid
Currently, our max tpt is limited to max HT A-MPDU for LB,
and max VHT A-MPDU for HB. Configure HE exponent value correctly to
achieve HE max A-MPDU, both on LB and HB.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.4486852ebb56.I9eb0d028e31f183597fb90120e7d4ca87e0dd6cb@changeid
ath11k_peer_create() is called without its return value being checked,
meaning errors will be unhandled. Add missing check and, as the mutex is
unconditionally unlocked on leaving this function, simplify the exit
path.
Addresses-Coverity-ID: 1497531 ("Code maintainability issues")
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-1-alex.dewar90@gmail.com
gcc-10 shows a false-positive warning with CONFIG_KASAN:
drivers/net/wireless/ath/ath9k/dynack.c: In function 'ath_dynack_sample_tx_ts':
include/linux/etherdevice.h:290:14: warning: writing 4 bytes into a region of size 0 [-Wstringop-overflow=]
290 | *(u32 *)dst = *(const u32 *)src;
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
Until gcc is fixed, work around this by using memcpy() in place
of ether_addr_copy(). Hopefully gcc-11 will not have this problem.
Link: https://godbolt.org/z/sab1MK
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97490
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[kvalo@codeaurora.org: remove ifdef and add a comment]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-8-arnd@kernel.org
WDS has long been superseded by 4-addr AP/client and lacks such
fundamental features like encryption, capability negotiation,
and similar. As such, it was basically always unusable as is.
Back in 2016, in commit 8f20542386 ("wireless: deprecate WDS
and disable by default") I disabled it and made the Kconfig option
only available under CONFIG_EXPERT to turn it back on. Since then,
nobody has complained about that, and given the severe limitations
with the code, it's unlikely anyone would have a reason to.
Remove the Kconfig option now, so we can clean up the associated
code in follow-up patches.
Link: https://lore.kernel.org/r/20201109105103.7d1e44c50e21.I2c0a1705fd6491d9ba3400c88415ee2c4832ae98@changeid
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are missig brcmf_free() for brcmf_alloc(). Fix memory leak
by adding missed brcmf_free().
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: a1f5aac176 ("brcmfmac: don't realloc wiphy during PCIe reset")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603849967-22817-1-git-send-email-sw0312.kim@samsung.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function ‘_rtl8812ae_phy_get_txpower_limit’:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:2453:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-35-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function ‘rtl8821ae_phy_switch_wirelessband’:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:597:14: warning: variable ‘rxpath’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:597:6: warning: variable ‘txpath’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-34-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8723be/trx.c: In function ‘_rtl8723be_query_rxphystatus’:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/trx.c:53:6: warning: variable ‘cck_highpwr’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-33-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_bt_inquiry’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1451:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_wifi_idle_process’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:1519:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:2990:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c: In function ‘btc8821a2ant_action_hid_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c:3277:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function ‘_rtl88e_phy_path_a_iqk’:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1351:33: warning: variable ‘reg_ea4’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-30-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c: In function ‘_rtl8723be_phy_lc_calibrate’:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/phy.c:2181:36: warning: variable ‘lc_cal’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-29-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a1ant.c: In function ‘btc8821a1ant_run_coexist_mechanism’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a1ant.c:1904:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function ‘_rtl8723e_phy_iq_calibrate’:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1150:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_wifi_idle_process’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:40: warning: variable ‘bt_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:1631:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_sco’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2767:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2810:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2855:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_a2dp_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2929:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2976:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_hs’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:22: warning: variable ‘wifi_rssi_state1’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3028:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3066:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_pan_edr_hid’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3121:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp_pan_edr’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3185:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c: In function ‘btc8723b2ant_action_hid_a2dp’:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3244:5: warning: variable ‘wifi_rssi_state’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:455: warning: Function parameter or member 'txdesc' not described in '_rtl_tx_desc_checksum'
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:124: warning: Function parameter or member 'hw' not described in 'rtl92c_llt_write'
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:124: warning: Excess function parameter 'io' description in 'rtl92c_llt_write'
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:155: warning: Function parameter or member 'hw' not described in 'rtl92c_init_llt_table'
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:155: warning: Excess function parameter 'io' description in 'rtl92c_init_llt_table'
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-4-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ti/wlcore/spi.c:403: warning: Function parameter or member 'child' not described in 'wl12xx_spi_set_block_size'
drivers/net/wireless/ti/wlcore/spi.c:403: warning: Function parameter or member 'blksz' not described in 'wl12xx_spi_set_block_size'
drivers/net/wireless/ti/wlcore/spi.c:440: warning: Excess function parameter 'res' description in 'wlcore_probe_of'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-36-lee.jones@linaro.org
Link: https://lore.kernel.org/r/20201102112410.1049272-37-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_pcie_remove’:
drivers/net/wireless/marvell/mwifiex/pcie.c:432:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/marvell/mwifiex/pcie.c: In function ‘mwifiex_cleanup_pcie’:
drivers/net/wireless/marvell/mwifiex/pcie.c:3142:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-32-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/wl3501_cs.c:57:
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:143: warning: Excess function parameter 'reg_comain' description in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:469: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw>
Cc: de Melo <acme@conectiva.com.br>
Cc: Gustavo Niemeyer <niemeyer@conectiva.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-25-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/intersil/prism54/isl_ioctl.c:22:
inlined from ‘prism54_get_name’ at drivers/net/wireless/intersil/prism54/isl_ioctl.c:283:2:
drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Function parameter or member 'priv' not described in 'prism54_mib_mode_helper'
drivers/net/wireless/intersil/prism54/isl_ioctl.c:68: warning: Excess function parameter 'mib' description in 'prism54_mib_mode_helper'
drivers/net/wireless/intersil/prism54/isl_ioctl.c:127: warning: Function parameter or member 'priv' not described in 'prism54_mib_init'
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aurelien Alleaume <slts@free.fr>
Cc: Valerio Riedel <hvr@gnu.org>
Cc: "Luis R. Rodriguez" <mcgrof@ruslug.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ti/wl1251/cmd.c:70: warning: Function parameter or member 'buf_len' not described in 'wl1251_cmd_test'
drivers/net/wireless/ti/wl1251/cmd.c:70: warning: Excess function parameter 'len' description in 'wl1251_cmd_test'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:394: warning: Function parameter or member 'gfp' not described in 'brcmf_fweh_process_event'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-19-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c:380: warning: Function parameter or member 'pktlist' not described in 'brcmf_sdiod_sglist_rw'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c:380: warning: Excess function parameter 'pkt' description in 'brcmf_sdiod_sglist_rw'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-7-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_usb_ops.c:22: warning: Incorrect use of kernel-doc format: * rsi_usb_rx_thread() - This is a kernel thread to receive the packets from
drivers/net/wireless/rsi/rsi_91x_usb_ops.c:29: warning: Function parameter or member 'common' not described in 'rsi_usb_rx_thread'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_usb.c:26: warning: cannot understand function prototype: 'u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; '
drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Function parameter or member 'endpoint' not described in 'rsi_write_multiple'
drivers/net/wireless/rsi/rsi_91x_usb.c:88: warning: Excess function parameter 'addr' description in 'rsi_write_multiple'
drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'ep_num' not described in 'rsi_rx_urb_submit'
drivers/net/wireless/rsi/rsi_91x_usb.c:320: warning: Function parameter or member 'mem_flags' not described in 'rsi_rx_urb_submit'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-3-lee.jones@linaro.org
rt2800 only gives you survey for current channel.
Survey-based ACS algorithms are failing to perform their job when working
with rt2800.
Make rt2800 save survey for every channel visited and be able to give away
that information.
There is a bug registered https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.
Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
sgruszka: remove unused variable
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104142524.94375-1-stf_xl@wp.pl
halbtc_send_bt_mp_operation() uses in_interrupt() to determine if it is
safe to invoke wait_for_completion().
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Aside of that in_interrupt() is not correct as it does not catch preempt
disabled regions which neither can sleep.
halbtc_send_bt_mp_operation() is called from:
rtl_watchdog_wq_callback()
rtl_btc_periodical()
halbtc_get()
case BTC_GET_U4_BT_PATCH_VER:
halbtc_get_bt_patch_version()
which is preemtible context.
rtl_c2h_content_parsing()
btc_ops->btc_btinfo_notify()
rtl_btc_btinfo_notify()
exhalbtc_bt_info_notify()
ex_btc8723b1ant_bt_info_notify()
ex_btc8821a1ant_bt_info_notify()
ex_btc8821a2ant_bt_info_notify()
btcoexist->btc_set_bt_reg()
halbtc_set_bt_reg()
rtl_c2h_content_parsing() is in turn called from:
rtl_c2hcmd_wq_callback()
rtl_c2hcmd_launcher()
which is preemptible context and from:
_rtl_pci_rx_interrupt
rtl_c2hcmd_enqueue()
which is obviously not preemptible but limited to C2H_BT_MP commands
which does invoke rtl_c2h_content_parsing().
Aside of that it can be reached from:
halbtc_get()
case BTC_GET_U4_SUPPORTED_FEATURE:
halbtc_get_bt_coex_supported_feature()
case BTC_GET_U4_BT_FORBIDDEN_SLOT_VAL:
halbtc_get_bt_forbidden_slot_val()
case BTC_GET_U4_BT_DEVICE_INFO:
halbtc_get_bt_device_info()
case BTC_GET_U4_SUPPORTED_VERSION:
halbtc_get_bt_coex_supported_version()
case BTC_GET_U4_SUPPORTED_FEATURE:
halbtc_get_bt_coex_supported_feature()
btcoexist->btc_get_bt_afh_map_from_bt()
halbtc_get_bt_afh_map_from_bt()
btcoexist->btc_get_ble_scan_para_from_bt()
halbtc_get_ble_scan_para_from_bt()
btcoexist->btc_get_ble_scan_type_from_bt()
halbtc_get_ble_scan_type_from_bt()
btcoexist->btc_get_ant_det_val_from_bt()
halbtc_get_ant_det_val_from_bt()
btcoexist->btc_get_bt_coex_supported_version()
halbtc_get_bt_coex_supported_version()
btcoexist->btc_get_bt_coex_supported_feature()
halbtc_get_bt_coex_supported_feature()
None of these have a caller. Welcome to the wonderful world of HALs and
onion layers.
Remove in_interrupt() check.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-9-bigeasy@linutronix.de
is_any_client_connect_to_ap() is using in_interrupt() to determine whether
it should acquire the lock prior accessing the list.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
The function is called from:
- halbtc_get()
- halbtc_get()
halbtc_get_wifi_link_status()
- halbtc_display_dbg_msg()
halbtc_display_wifi_status()
halbtc_get_wifi_link_status()
All top level callers are part of the btc_coexist callback inferface and
are never invoked from a context which can hold the lock already.
The contexts which hold the lock are either protecting list add/del
operations or list walks which never call into any of the btc_coexist
interfaces.
In fact the conditional is outright dangerous because if this function
would be invoked from a BH disabled context the check would avoid taking
the lock while on another CPU the list could be manipulated under the lock.
Remove the in_interrupt() check and always acquire the lock.
To simplify the code further use list_empty() instead of walking the list
and counting the entries just to check the count for > 0 at the end.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-8-bigeasy@linutronix.de
The usage of in_atomic() in driver code is deprecated as it can not
always detect all states where it is not allowed to sleep.
All callers are in premptible thread context and all functions invoke core
functions which have checks for invalid calling contexts already.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-7-bigeasy@linutronix.de
hostap_get_wireless_stats() is the iw_handler_if::get_wireless_stats()
callback of this driver. This callback was not allowed to sleep until
commit a160ee69c6 ("wext: let get_wireless_stats() sleep") in v2.6.32.
Remove the therefore pointless in_atomic() check.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-6-bigeasy@linutronix.de
issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.
Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Add an may_sleep argument to issuecommand() indicating when it is save to
sleep and change schedule() to cond_resched() because it's pointless to
invoke schedule() if there is no request to reschedule.
Pass the may_sleep condition through the various call chains leading to
issuecommand().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-5-bigeasy@linutronix.de
issuecommand() is using in_atomic() to decide if it is safe to invoke
schedule() while waiting for the command to be accepted.
Usage of in_atomic() for this is only half correct as it can not detect all
condition where it is not allowed to schedule(). Also Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
Chasing the call chains leading up to issuecommand() is straight forward,
but airo_link() and airo_get_stats() would require to pass the context
through a quite large amount of functions.
As this is ancient hardware, avoid the churn and enforce the invocation of
those functions through the JOB machinery.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-4-bigeasy@linutronix.de
airo_get_wireless_stats() is the iw_handler_if::get_wireless_stats()
callback of this driver. This callback was not allowed to sleep until
commit a160ee69c6 ("wext: let get_wireless_stats() sleep") in v2.6.32.
airo still delegates the readout to a thread, which is not longer
necessary.
Invoke airo_read_wireless_stats() directly from the callback and remove
the now unused JOB_WSTATS handling.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-3-bigeasy@linutronix.de
The usage of in_irq()/in_interrupt() in drivers is phased out and the
BUG_ON()'s based on those are not covering all contexts in which these
functions cannot be called.
Aside of that BUG_ON() should only be used as last resort, which is clearly
not the case here.
A broad variety of checks in the invoked functions (always enabled or debug
option dependent) cover these conditions already, so the BUG_ON()'s do not
really provide additional value.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201101211536.2966644-2-bigeasy@linutronix.de
This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com
Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com
Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com
In current flow, driver issues power requests to firmware for entering or
leaving deep power mode. But driver does not wait for an ack from firmware
via reading CPWM register when driver requests to enter deep power mode.
The behavior will lead to unsynchronized state between firmware and driver.
Furthermore, consecutive same power requests may confuse firmware and leads
to unexpected value of CPWM register. This patch ensures that the power
request will wait for an ack from firmware and only send one power request
each time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-2-tehuang@realtek.com
BT firmware will report BLE-HID and BLE-RCU in different profile.
We can distinguish the two profile from BT info now.
Add the coexistence for BLE-HID coexistence,
it can make BLE HID work more smoothly.
BLE-HID need to Tx/Rx packet more frequently to respond
user operation, but RCU doesn't.
In the case of RCU coexistence, it will make Wi-Fi have a
higher priority to earn more Wi-Fi throughput.
If BLE-HID go for the same case,
it will make user feel mouse is lagging.
Desired BT firmware BT-COEX version: 0x1c
Desired WL firmware version: 9.9
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030055506.6560-1-pkshih@realtek.com
During realtek USB wireless NIC initialization, it's unexpected
disconnection will cause urb sumbmit fail. On the one hand,
_rtl_usb_cleanup_rx will be called to clean up rx stuff, especially for
rtl_wq. On the other hand, disconnection will cause rtl_usb_disconnect
and _rtl_usb_cleanup_rx to be called. So, rtl_wq will be flush/destroy
twice, which will cause non-canonical address 0xdead000000000122 access
and general protection fault.
Fixed this issue by remove _rtl_usb_cleanup_rx when urb sumbmit fail.
Signed-off-by: WeitaoWangoc <WeitaoWang-oc@zhaoxin.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603768580-2798-1-git-send-email-WeitaoWang-oc@zhaoxin.com
These full-mac chips use little-endian byte ordering. This patch
adds a few missing conversions to/from little-endian so that the
driver may be used with a big-endian host.
Signed-off-by: Remi Depommier <rde@setrix.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020174639.28892-1-rde@setrix.com
clang -Wextra warns about functions returning a 'const' integer:
drivers/net/wireless/realtek/rtw88/rtw8822b.c:90:8: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
static const u8 rtw8822b_get_swing_index(struct rtw_dev *rtwdev)
Remove the extra qualifier here.
Fixes: c97ee3e0be ("rtw88: add power tracking support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-7-arnd@kernel.org
There are thousands of warnings in a W=2 build from just one file:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/table.c:3788:15: warning: pointer targets in initialization of 'u8 *' {aka 'unsigned char *'} from 'char *' differ in signedness [-Wpointer-sign]
Change the types to consistently use 'const char *' for the
strings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-6-arnd@kernel.org
gcc -Wextra complains about the function type cast:
drivers/net/wireless/intersil/hostap/hostap_hw.c:3173:48: warning: cast between incompatible function types from ‘void (*)(struct tasklet_struct *)’ to ‘void (*)(long unsigned int)’ [-Wcast-function-type]
Avoid this by just using the regular tasklet_setup() function instead
of the incorrect homegrown version.
Fixes: 7433c96903 ("intersil: convert tasklets to use new tasklet_setup() API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-2-arnd@kernel.org
In case RSI9116 SDIO WiFi operates in STA mode against Intel 9260 in AP mode,
the association fails. The former is using wpa_supplicant during association,
the later is set up using hostapd:
iwl$ cat hostapd.conf
interface=wlp1s0
ssid=test
country_code=DE
hw_mode=g
channel=1
wpa=2
wpa_passphrase=test
wpa_key_mgmt=WPA-PSK
iwl$ hostapd -d hostapd.conf
rsi$ wpa_supplicant -i wlan0 -c <(wpa_passphrase test test)
The problem is that the TX EAPOL data descriptor RSI_DESC_REQUIRE_CFM_TO_HOST
flag and extended descriptor EAPOL4_CONFIRM frame type are not set in case the
AP is iwlwifi, because in that case the TX EAPOL packet is 2 bytes shorter.
The downstream vendor driver has this change in place already [1], however
there is no explanation for it, neither is there any commit history from which
such explanation could be obtained.
[1] https://github.com/SiliconLabs/RS911X-nLink-OSD/blob/master/rsi/rsi_91x_hal.c#L238
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015111616.429220-1-marex@denx.de
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-3-allen.lkml@gmail.com
Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.
This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Excess function parameter 'ptr' description in 'wmi_buffer_block'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-2-lee.jones@linaro.org
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.
This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
gcc -Wextra points out a type mismatch
drivers/net/wireless/ath/ath6kl/wmi.c: In function 'ath6kl_wmi_cmd_send':
drivers/net/wireless/ath/ath6kl/wmi.c:1825:19: warning: implicit conversion from 'enum <anonymous>' to 'enum wmi_data_hdr_data_type' [-Wenum-conversion]
1825 | false, false, 0, NULL, if_idx);
| ^~~~~
As far as I can tell, the numeric value is current here,
so just use the correct enum literal instead of 'false'.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-9-arnd@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'old' not described in 'ath_dynack_ewma'
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'new' not described in 'ath_dynack_ewma'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-40-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'rfBuf' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'reg32' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'numBits' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'firstBit' not described in 'ar5008_hw_phy_modify_rx_buffer'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1734:18: warning: ‘ar9300PciePhy_clkreq_disable_L1_2p2’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1727:18: warning: ‘ar9300PciePhy_clkreq_enable_L1_2p2’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9485_initvals.h:1009:18: warning: ‘ar9485_fast_clock_1_1_baseband_postamble’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9340_initvals.h:624:18: warning: ‘ar9340Modes_ub124_tx_gain_table_1p0’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9330_1p1_initvals.h:1013:18: warning: ‘ar9331_common_tx_gain_offset1_1’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-11-lee.jones@linaro.org
There are only a couple of these and none of them are conformant.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pri_detector.c:39: warning: Function parameter or member 'head' not described in 'pulse_elem'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'val' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'fraction' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'tolerance' not described in 'pde_get_multiple'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pattern_detector.c:34: warning: Function parameter or member 'region' not described in 'radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:141: warning: Function parameter or member 'region' not described in 'get_dfs_domain_radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'dpd' not described in 'channel_detector_get'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'freq' not described in 'channel_detector_get'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/regd.c:378: warning: Function parameter or member 'reg' not described in 'ath_reg_apply_ir_flags'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-20-lee.jones@linaro.org
Japan has new Radar types as per latest regulatory,
included under MKK_N in FW. So adding new enum in
ath11k to support it.
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.4.0.1-00041-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604563475-5782-1-git-send-email-lavaks@codeaurora.org
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits
No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org
driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.
caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.
This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.
The device tree requires an additional string to define the variant name
wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};
This would create the boarddata identifier for the board-2.bin search
* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
Monitor ring Rx buffer is not really modified between dma map
and unmap. So remove the unnecssary data sync before dma unmap.
This does not fix any visible issue, found in code review.
Compile tested only.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602744454-22969-1-git-send-email-vthiagar@codeaurora.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-4-allen.lkml@gmail.com
The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org
This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.
Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org
The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.
Also, increment the variable i inline for clarity
Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
The clang build reports this warning
fw.c:1485:21: warning: address of array 'rtwdev->chip->fw_fifo_addr'
will always evaluate to 'true'
if (!rtwdev->chip->fw_fifo_addr) {
fw_fifo_addr is an array in rtw_chip_info so it is always
nonzero. A better check is if the first element of the array is
nonzero. In the cases where fw_fifo_addr is initialized by rtw88b
and rtw88c, the first array element is 0x780.
Fixes: 0fbc2f0f34 ("rtw88: add dump firmware fifo support")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201011155438.15892-1-trix@redhat.com
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no new drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g+oQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAyQCghI58tN/Np3itPlZuc+HYFN7OHH8An1TKzCm1
bwkfw5qAcHab+R7KQZOA
=BaXS
-----END PGP SIGNATURE-----
Merge tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no staging drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (476 commits)
staging: comedi: check validity of wMaxPacketSize of usb endpoints found
staging: wfx: improve robustness of wfx_get_hw_rate()
staging: wfx: drop unicode characters from strings
staging: wfx: gpiod_get_value() can return an error
staging: wfx: increase robustness of hif_generic_confirm()
staging: wfx: wfx_init_common() returns NULL on error
staging: wfx: standardize the error when vif does not exist
staging: wfx: check memory allocation
staging: wfx: improve error handling of hif_join()
staging: dpaa2-switch: add a dpaa2_switch prefix to all functions in ethsw.c
staging: dpaa2-switch: add a dpaa2_switch_ prefix to all functions in ethsw-ethtool.c
staging: rtl8188eu: Fix long lines
dt-bindings: staging: wfx: silabs,wfx yaml conversion
staging: wfx: update copyrights dates
staging: wfx: fix QoS priority for slow buses
staging: wfx: fix BA sessions for older firmwares
staging: wfx: remove remaining code of 'secure link' feature
staging: wfx: fix handling of MMIC error
staging: vchiq: Fix list_for_each exit tests
staging: greybus: use __force when assigning __u8 value to snd_ctl_elem_type_t
...
Simplify the code by using new function dev_fetch_sw_netstats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/166259f2-084c-45d7-e610-2de2a0bdae06@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull crypto updates from Herbert Xu:
"API:
- Allow DRBG testing through user-space af_alg
- Add tcrypt speed testing support for keyed hashes
- Add type-safe init/exit hooks for ahash
Algorithms:
- Mark arc4 as obsolete and pending for future removal
- Mark anubis, khazad, sead and tea as obsolete
- Improve boot-time xor benchmark
- Add OSCCA SM2 asymmetric cipher algorithm and use it for integrity
Drivers:
- Fixes and enhancement for XTS in caam
- Add support for XIP8001B hwrng in xiphera-trng
- Add RNG and hash support in sun8i-ce/sun8i-ss
- Allow imx-rngc to be used by kernel entropy pool
- Use crypto engine in omap-sham
- Add support for Ingenic X1830 with ingenic"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (205 commits)
X.509: Fix modular build of public_key_sm2
crypto: xor - Remove unused variable count in do_xor_speed
X.509: fix error return value on the failed path
crypto: bcm - Verify GCM/CCM key length in setkey
crypto: qat - drop input parameter from adf_enable_aer()
crypto: qat - fix function parameters descriptions
crypto: atmel-tdes - use semicolons rather than commas to separate statements
crypto: drivers - use semicolons rather than commas to separate statements
hwrng: mxc-rnga - use semicolons rather than commas to separate statements
hwrng: iproc-rng200 - use semicolons rather than commas to separate statements
hwrng: stm32 - use semicolons rather than commas to separate statements
crypto: xor - use ktime for template benchmarking
crypto: xor - defer load time benchmark to a later time
crypto: hisilicon/zip - fix the uninitalized 'curr_qm_qp_num'
crypto: hisilicon/zip - fix the return value when device is busy
crypto: hisilicon/zip - fix zero length input in GZIP decompress
crypto: hisilicon/zip - fix the uncleared debug registers
lib/mpi: Fix unused variable warnings
crypto: x86/poly1305 - Remove assignments with no effect
hwrng: npcm - modify readl to readb
...
Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.
Major changes:
iwlwifi
* PNVM support (platform-specific phy config data)
* bump the FW API support to 59
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfgIilAAoJEG4XJFUm622b/MoH+wfx+CnW2J49uRAlAiAyJ8oW
pBKvJF1b6kbLeWurQPQH6ecmmYy0H/Cr8Zy4IW+YP7XN5PbSpDe4HXH6GkLP41fv
73kd0qHPFp42dmArImCqd8+9vAuh6C/taHSPV8klGaSfATUvvDIwgPrxGJnaGvwm
3E+SOnGcvqRV1fkBi7CArdIa1DzZwyu9q9zvQKbElmL7lX/r5kAzkHZqlMr3ZyjO
Gvuzvz9FIKvkU81IxtR8VXJh5RQ9WCXvsa00ZoP489jUz/lUoC2Rjofn55BcdAIh
1V4N7yOM2KFjDo3RWGZo+fqNo6LXREMyVQetmXCWPzFzCkMTN5FCWuj182dnYIM=
=9NpN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.
Major changes:
iwlwifi
* PNVM support (platform-specific phy config data)
* bump the FW API support to 59
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver looks for a PNVM file that contains FW configuration data
for each different HW combination. The FW requests the data for a
certain SKU_ID and the driver tries to find it in the PNVM file.
Read the file, parse its contents and send it to the trans.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.826bc607e57a.I1d93dd6e6651586878db57fac3e7c3f09d742c42@changeid
When adding support for version 3 of the GEO_TX_POWER_LIMIT command,
the table argument of iwl_sar_geo_init was changed from a pointer a 1d
array of now-removed iwl_per_chain_offset_group_v1 to a pointer to a 2d
array of iwl_per_chain_offset (iwl_per_chain_offset_group_v1 was a
struct containing 2 copies of iwl_per_chain_offset).
So even for version 2 where the second dimension is of length 2, which
means that the underlying memory layout of the array didn't change, this
requires a small change in the way we loop over it, and this was missed.
Additionally, for the case of version 3 where the second dimension is now
3, in order to fill the first two elements of each row correctly (lb and
hb), iwl_sar_geo_init must get the true number of bands supported.
But because we don't yet store any values for the 3rd (uhb) band, skip
that band.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.73605b6e0548.Id0ec98333277ff9e017e3938ae413b34acc68947@changeid
iwl_mvm_wowlan_program_keys is now setting data directly in
the KEK_KCK command, and the memset is clearing this later,
causing the data to be incomplete.
Just remove the memory clearing, the structure is local and
cleared in the declaration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.0f355b4578c5.Ifbb76a2814925f215a2c889c1792d46d5bd66ab8@changeid
We introduced a new flow to remove an on-going CSA but we
assumed the firwmare understands the
CHANNEL_SWITCH_TIME_EVENT_CMD. This is not true for 7265 and down.
Don't send this command for those devices, but rather use the older
command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.2574e3e47927.Ic0c56411da1096e9a45ee5c3383edf777c5baca0@changeid
We were using a very high latency for all 9560 devices so they all
would have time to stabilize. But this causes the system to be
slighly slower, so we can use the best values for each device.
This requires a new trans cfg struct for devices with longer latency
and some adjustments to the other structs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.34392f98fdb1.I3d3db14f6d1a8ecc547ca6afce8488816bd26081@changeid
ADD_STA_CMD_API_S ver 12 was added in order to properly support
auxiliary activities in CDB NICs. In the new version we don't need
to allocate an aux station at initialization, instead we add an
aux station only when an auxiliary activity that requires a dedicated Tx
queue is needed. For now the only case we need this kind of activity is
when using hot spot 2.0
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.700e6e2e3077.Icdd807b6a3ad3fed806449ea0a13f856aa20e632@changeid
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
The FW relies on the re-enablement of the TX in order to know
it can exit quiet mode. Currently in case of CSA with quiet mode,
the quiet mode is never cancelled, resulting in a complete traffic
hang.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.fee389c83ded.I09550fdadb61f899242d7e7b7578672372e2b7fe@changeid
If we have only a single RX queue, such as when MSI-X is not
available, we should not send the RFH_QUEUEU_CONFIG_CMD, because our
only queue is the same as the command queue and will be configured as
part of the context info. Our code was actually trying to send the
command with 0 queues, which caused UMAC assert 0x1D04.
Fix that by not sending the command when we have a single queue.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.c35eeb3299f8.I08f79a6ebe150a7d180b7005b24504bfdba6d8b5@changeid
The legacy_httxpowerdiff in rtl8192se is pretty much the same as
the legacy_ht_txpowerdiff for other chips. Use the same name to
keep the consistency.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201006035928.5566-1-chiu@endlessm.com
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
In ath11k_mac_setup_iface_combinations(), if memory cannot be assigned
for the variable limits, then the memory assigned to combinations will
be leaked. Fix this.
Addresses-Coverity-ID: 1497534 ("Resource leaks")
Fixes: 2626c26970 ("ath11k: add interface_modes to hw_params")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-2-alex.dewar90@gmail.com
Also demote a non-conforming kernel-doc function header.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_drv' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_trans' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:124: warning: Function parameter or member 'dbgfs_op_mode' not described in 'iwl_drv'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:1329: warning: Function parameter or member 'ucode_raw' not described in 'iwl_req_fw_callback'
drivers/net/wireless/intel/iwlwifi/iwl-drv.c:1329: warning: Function parameter or member 'context' not described in 'iwl_req_fw_callback'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-16-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:66: warning: Function parameter or member 'priv' not described in 'iwl_beacon_time_mask_low'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:66: warning: Function parameter or member 'tsf_bits' not described in 'iwl_beacon_time_mask_low'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:77: warning: Function parameter or member 'priv' not described in 'iwl_beacon_time_mask_high'
drivers/net/wireless/intel/iwlwifi/dvm/devices.c:77: warning: Function parameter or member 'tsf_bits' not described in 'iwl_beacon_time_mask_high'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'rate_n_flags' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'info' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1431: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_get_scd_ssn'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:695: warning: bad line:
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:701: warning: Function parameter or member 'priv' not described in 'iwl_set_rxon_channel'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:701: warning: Function parameter or member 'ctx' not described in 'iwl_set_rxon_channel'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:839: warning: Function parameter or member 'ctx' not described in 'iwl_full_rxon_required'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:1029: warning: Function parameter or member 'priv' not described in 'iwlagn_commit_rxon'
drivers/net/wireless/intel/iwlwifi/dvm/rxon.c:1029: warning: Function parameter or member 'ctx' not described in 'iwlagn_commit_rxon'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-13-lee.jones@linaro.org
2 of which do not attempt to document their parameters, 1 does a poor job.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:193: warning: Function parameter or member 'priv' not described in 'iwl_scan_cancel'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:205: warning: Function parameter or member 'priv' not described in 'iwl_scan_cancel_timeout'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'frame' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ta' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ies' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ie_len' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ssid' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'ssid_len' not described in 'iwl_fill_probe_req'
drivers/net/wireless/intel/iwlwifi/dvm/scan.c:570: warning: Function parameter or member 'left' not described in 'iwl_fill_probe_req'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-12-lee.jones@linaro.org
Fix misnamed, and missing descriptions likely due to doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'lq' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Excess function parameter 'sync' description in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'vif' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'smps_request' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Excess function parameter 'smps_requests' description in 'iwl_mvm_update_smps'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'priv' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'cur_ofdm' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'cur_ofdm_ht' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:145: warning: Function parameter or member 'msecs' not described in 'iwlagn_good_plcp_health'
drivers/net/wireless/intel/iwlwifi/dvm/rx.c:939: warning: Function parameter or member 'priv' not described in 'iwl_setup_rx_handlers'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-10-lee.jones@linaro.org
Looks as if it's never been used.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/ops.c:466:36: warning: ‘iwl_mvm_debug_names’ defined but not used [-Wunused-const-variable=]
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'priv' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'ctx' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'addr' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'is_ap' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:244: warning: Function parameter or member 'sta' not described in 'iwl_prep_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'priv' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'ctx' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'addr' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'is_ap' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'sta' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:332: warning: Function parameter or member 'sta_id_r' not described in 'iwl_add_station_common'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:390: warning: Function parameter or member 'priv' not described in 'iwl_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:390: warning: Function parameter or member 'sta_id' not described in 'iwl_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'priv' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'sta_id' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:459: warning: Function parameter or member 'addr' not described in 'iwl_remove_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:614: warning: Function parameter or member 'priv' not described in 'iwl_clear_ucode_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:614: warning: Function parameter or member 'ctx' not described in 'iwl_clear_ucode_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:648: warning: Function parameter or member 'priv' not described in 'iwl_restore_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:648: warning: Function parameter or member 'ctx' not described in 'iwl_restore_stations'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'priv' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'ctx' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:790: warning: Function parameter or member 'lq' not described in 'is_lq_table_valid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'priv' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'ctx' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'lq' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:822: warning: Function parameter or member 'flags' not described in 'iwl_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1270: warning: Function parameter or member 'priv' not described in 'iwlagn_alloc_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1270: warning: Function parameter or member 'ctx' not described in 'iwlagn_alloc_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1309: warning: Function parameter or member 'priv' not described in 'iwl_update_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1309: warning: Function parameter or member 'ctx' not described in 'iwl_update_bcast_station'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'priv' not described in 'iwl_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'sta_id' not described in 'iwl_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1348: warning: Function parameter or member 'tid' not described in 'iwl_sta_tx_modify_enable_tid'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-8-lee.jones@linaro.org
This is the only use of kerneldoc in the sourcefile and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'priv' not described in 'iwl_find_disconn_antenna'
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'average_sig' not described in 'iwl_find_disconn_antenna'
drivers/net/wireless/intel/iwlwifi/dvm/calib.c:770: warning: Function parameter or member 'data' not described in 'iwl_find_disconn_antenna'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-6-lee.jones@linaro.org
Neither of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:121: warning: Function parameter or member 'priv' not described in 'iwlagn_txfifo_flush'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:121: warning: Function parameter or member 'scd_q_msk' not described in 'iwlagn_txfifo_flush'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:779: warning: Function parameter or member 'priv' not described in 'iwlagn_set_rxon_chain'
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:779: warning: Function parameter or member 'ctx' not described in 'iwlagn_set_rxon_chain'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-5-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'priv' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'rate_n_flags' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:811: warning: Function parameter or member 'info' not described in 'iwlagn_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:1267: warning: Function parameter or member 'priv' not described in 'iwlagn_rx_reply_compressed_ba'
drivers/net/wireless/intel/iwlwifi/dvm/tx.c:1267: warning: Function parameter or member 'rxb' not described in 'iwlagn_rx_reply_compressed_ba'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-4-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:165: warning: cannot understand function prototype: 'const u16 expected_tpt_legacy[IWL_RATE_COUNT] = '
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:329: warning: Function parameter or member 'priv' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:329: warning: Function parameter or member 'lq_sta' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'tbl' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'scale_index' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'attempts' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:452: warning: Function parameter or member 'successes' not described in 'rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:681: warning: Function parameter or member 'sta' not described in 'rs_use_green'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'lq_sta' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'hdr' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:702: warning: Function parameter or member 'rate_type' not described in 'rs_get_supported_rates'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2628: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'priv' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/dvm/rs.c:2632: warning: Function parameter or member 'lq_sta' not described in 'rs_initialize_lq'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-3-lee.jones@linaro.org
None of these headers attempt to document any function parameters.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/dvm/main.c:388: warning: Function parameter or member 't' not described in 'iwl_bg_statistics_periodic'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:545: warning: Function parameter or member 't' not described in 'iwl_bg_ucode_trace'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:771: warning: Function parameter or member 'priv' not described in 'iwl_alive_start'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'priv' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'start_idx' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'num_events' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'mode' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'pos' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'buf' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1692: warning: Function parameter or member 'bufsz' not described in 'iwl_print_event_log'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'priv' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'capacity' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'num_wraps' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'next_entry' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'size' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'mode' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'pos' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'buf' not described in 'iwl_print_last_event_logs'
drivers/net/wireless/intel/iwlwifi/dvm/main.c:1772: warning: Function parameter or member 'bufsz' not described in 'iwl_print_last_event_logs'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-2-lee.jones@linaro.org
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfdzOKAAoJEG4XJFUm622bAxEH/2XBLA6RJ0/ypDYt32qj7q5/
hgV3tQkaCXTKnXo0O/6DtihdLD1gARg3Y8s1BY4wHzIZ57iR2LxKumzDS9f6S2oq
6/7OmBubZVzK8oii2bTleOu524Dfq6B019uOgtQJMAOT5S5X5uk25PDIfVCksv5m
ZKSNZINFqC2K9cQkXKP0cD0SSJDDHvcMjI8/nZ91mNLJ7StO3En4WDNMQJ7Jfa3M
VX18GI6XB/pqb18+QJwTXUKN4jODTYHH8zJ6LvYfDFq9vhN2GomdK5f3W9teIUwY
omQavKAFCPAhBja61IVGyo47ZB3MH57ECyuuBtAPv/ydcwAGXlJToHO8avM4K7I=
=WApP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Third set of patches for v5.10. Lots of iwlwifi patches this time, but
also few patches ath11k and of course smaller changes to other
drivers.
Major changes:
rtw88
* properly recover from firmware crashes on 8822c
* dump firmware crash log
iwlwifi
* protected Target Wake Time (TWT) implementation
* support disabling 5.8GHz channels via ACPI
* support VHT extended NSS capability
* enable Target Wake Time (TWT) by default
ath11k
* improvements to QCA6390 PCI support to make it more usable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
-----BEGIN PGP SIGNATURE-----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=B9Xl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, this time with:
* lots more S1G band support
* 6 GHz scanning, finally
* kernel-doc fixes
* non-split wiphy dump fixes in nl80211
* various other small cleanups/features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.10. Major changes:
ath11k
* improvements to QCA6390 PCI support, adding essential missing
features: ELF board files, packet log handling to avoid data stalls
and crash fixes
In bmps mode, beacons are filtered, and firmware is in charge
of monitoring the beacons and report changes or loss.
mac80211 must be advertised about such change to prevent it's
internal timer based beacon monitor to report beacon loss.
Fix that by setting/clearing the IEEE80211_VIF_BEACON_FILTER
vif flag on bmps entry/exit.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592471863-31402-2-git-send-email-loic.poulain@linaro.org
Host sends wmi command to allow hardware enter idle power
save mode in ath11k_mac_op_start function.
hw parameter idle_ps indicates whether idle power save is supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-8-git-send-email-kvalo@codeaurora.org
For QCA6390, Start a timer to update CE pipe 4 ring HP when shadow
register is enabled. Its' to avoid that HP isn't updated to target
register.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-7-git-send-email-kvalo@codeaurora.org
Start a timer to update REO HP if HP isn't updated to target.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-6-git-send-email-kvalo@codeaurora.org
The timer is to check if TCL HP isn't updated to target.
The timer will postpone itself if there are TX operations
during the interval, otherwise the timer handler updates
the HP again so the index value in HP register will be
forwarded to target register, and the timer stops afterwards.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-5-git-send-email-kvalo@codeaurora.org
For QCA6390, set wmi credit to 1 to avoid back-to-back write to
shadow register when shadow register is enabled.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-4-git-send-email-kvalo@codeaurora.org
To enable shadow register access, host needs to pass shadow
register configuration to firmware via qmi message. Host also
needs to update ring's HP or TP address to shadow register
address. The write operation to shadow register will be
forwarded to target register by hardware automatically, and
the write operation to shadow register is permitted even
when the target is in power save or sleep mode.
Update the shadow config whenever power up happens.
This feature is controlled by hw parameter supports_shadow_regs which is only
enabled for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org
For QCA6390, host can read and write registers below unwindowed
address directly without programming the window register. For
registers below bar0 + 4k - 32, host can read and write regardless
of the power save state. Shadow registers are located below
bar0 + 4K - 32.
Before MHI power up, there is no need to wakeup MHI so ini_done is
added to indicate it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-2-git-send-email-kvalo@codeaurora.org
Add packet log support for QCA6390, otherwise the data connection will stall
within a minute or so. Enable it via debugfs and use trace-cmd to capture the
pktlogs.
echo 0xffff 1 > /sys/kernel/debug/ath11k/qca6390\ hw2.0/mac0/pktlog_filter
The mon status ring doesn't support interrupt so far, so host starts
a timer to reap this ring. The timer handler also reaps the
rxdma_err_dst_ring in case of monitor mode.
As QCA6390 requires bss created ahead of starting vdev, so check
vdev_start_delay for monitor mode.
For QCA6390, it uses wbm_desc_rel_ring to return descriptors.
It also uses rx_refill_buf_ring to fill mon buffer instead of
rxdma_mon_buf_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601463073-12106-2-git-send-email-kvalo@codeaurora.org
QCA6390 does not support monitor mode at the moment so disable it altogether,
using a hack as mac80211 does not support disabling it otherwise. Add a boolean
to hw_params to know if hardware supports monitor mode.
IPQ8074 continues to support monitor mode normally.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-6-git-send-email-kvalo@codeaurora.org
There are different versions of QCA6390. Check TCSR_SOC_HW_VERSION to make sure
that the device is hw2.0, all the rest are unsupported.
This needs to be checked after ath11k_pci_claim() so move the whole switch choosing hw_ver.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-5-git-send-email-kvalo@codeaurora.org
As QCA6390 does not support mesh interfaces, move the interface_modes to
hw_params. Also create interface combinations dynamically so that it's easy to
change the values.
Now QCA6390 does not claim to support mesh interfaces to user space, but
IPQ8074 continues to do that.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-4-git-send-email-kvalo@codeaurora.org
For QCA6390, station vdev needs to delay startup but not for AP mode. On AP
mode vdev starts up immediately after bss peer is created in chanctx assignment
context.
This patch does not affect IPQ8074 family of devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-3-git-send-email-kvalo@codeaurora.org
The QCA6390 board I have, model 8291M-PR comes with an ELF board file. To get
this to at least somewhat work, I renamed bdwlan.e04 to 'board.bin' and then
added this patch to check for ELF magic string in the beginning of the file.
If that is found, use type ELF. After this the driver loads.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@codeaurora.org: use elf.h, minor cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-2-git-send-email-kvalo@codeaurora.org
debugfs_create_dir() returns an ERR_PTR in case of error, but never a
null pointer. There are a number of places where error-checking code can
accordingly be simplified.
Addresses-Coverity: CID 1497150: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497158: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497160: Memory - illegal accesses (USE_AFTER_FREE)
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200927132451.585473-1-alex.dewar90@gmail.com
* Protected TWT implementation;
* Support disabling 5.8GHz channels via ACPI;
* Support VHT extended NSS capability;
* A few fixes in the datapath;
* Enable TWT by default;
* Support new PPAG FW command version
* Move some trans code around for better abstraction;
* Some clean-ups in the ACPI code;
* A fix for AP mode;
* Updates in the ACPI code to support new tables and FW versions;
* FTM updates;
* A bit of reorganiztion in the queue code;
* A few debugging infra improvements;
* Add support for new GTK rekeying;
* A fix in the scanning code;
* Support for some new cards;
* Some updates for new or changed FW APIs;
* Some new FW API command version implementations;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=ytv5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-09-30-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi patches intended for v5.10
* Protected TWT implementation;
* Support disabling 5.8GHz channels via ACPI;
* Support VHT extended NSS capability;
* A few fixes in the datapath;
* Enable TWT by default;
* Support new PPAG FW command version
* Move some trans code around for better abstraction;
* Some clean-ups in the ACPI code;
* A fix for AP mode;
* Updates in the ACPI code to support new tables and FW versions;
* FTM updates;
* A bit of reorganiztion in the queue code;
* A few debugging infra improvements;
* Add support for new GTK rekeying;
* A fix in the scanning code;
* Support for some new cards;
* Some updates for new or changed FW APIs;
* Some new FW API command version implementations;
* Some other small fixes and clean-ups;
# gpg: Signature made Thu 01 Oct 2020 10:04:00 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
Add support for the new version of the alive notification, which
includes the SKU ID. We don't use the SKU ID yet, so we can just
handle the new notification as if it were version 4.
While at it, clean up a bit and rename the command and structure names
in the comments so that they are aligned with the ones used in the FW.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6024b149e9e2.Ifcadb506e994ec352e9ce54399719926bc1bb7ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request may specify the request scan dwell time.
However, this value may not always be optimal (e.g. short dwell
time for a passive channel). This may happen in a scan request
as a result of beacon report request, in which the AP may request
an active scan, thus setting a short dwell time, but the station
will perform a passive scan due to regulatory.
Ignore the scan duration parameter and always use the internal
scan dwell time which should be optimal.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6e1d2b8b4489.I9584bb40d44bf31131f57fdd32d5e8848d4fbdd8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To avoid duplicating code we need to call iwl_pcie_txq_update_byte_cnt_tbl
function from non bus independent code so make it bus independent.
Used spatch rule
@r1@
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->scd_bc_tbls
+trans->txqs.scd_bc_tbls
|
-iwl_pcie_txq_update_byte_cnt_tbl
+iwl_txq_gen1_update_byte_cnt_tbl
|
-iwl_pcie_txq_inval_byte_cnt_tbl
+iwl_txq_gen1_inval_byte_cnt_tbl
|
-iwl_pcie_tfd_unmap
+iwl_txq_gen1_tfd_unmap
|
-iwl_pcie_tfd_tb_get_addr
+iwl_txq_gen1_tfd_tb_get_addr
|
-iwl_pcie_tfd_tb_get_len
+iwl_txq_gen1_tfd_tb_get_len
|
-iwl_pcie_tfd_get_num_tbs
+iwl_txq_gen1_tfd_get_num_tbs
)
/* clean all new unused variables */
@ depends on r1@
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.8d33e791ec8c.Ica35125ed640aa3aa1ecc38fb5e8f1600caa8df6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is being updated to report version 11 of this
response in order to include BIGTK material. Parse it, but
for now keep the existing behaviour of disconnecting on any
rekeying with even IGTK presence, need to fix that before
BIGTK can be supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.b7098f097a5c.I4ae1c5b2186b0e04702233a7a7068d69cfd3361a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some bits declared here that simply don't exist
in the firmware, and some are missing (e.g. the key) from
what the firmware has. Align this and move all the fields
into a single one for this status word, which makes this a
bit easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.0ba403d72e7c.I5fa3aa0538f3fbf8c3885b27a1204b5b0464c20a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are printing the same thing twice, "Enabling TXQ #%d". Previously
the second print was including more information, but now it only
prints the queue number, which is already in the first print. Remove
the redundant one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.1c22d1bc0a88.I24e57317bdddc6c72f69725e1d95683a935e893d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The API added the ability to send for CDB nic what LMAC ID
the cmd belongs to.
Also driver always set apply_time to zero so no need to pass it as
a param and anyway in new API it's removed for no use.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fa11d1f523b6.Id105899da82c2b08ee62b57133c4ff72bfd0bb80@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New API for temperature measurement (DTS_MEASUREMENT_TRIGGER)
involves getting an immediate response from FW, and not waiting
for a notification like in previous APIs. Support new API while
keeping backwards compatibility.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.b4893554d8e7.Ia4d7f389d4ac3256fcfe3ce6144e924dd6dbf6eb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Every time we call init_cfg driver appends the enabled triggers
to the active triggers while this should be done only once per
driver load.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 14124b2578 ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.79bd622e604a.Ie0f79d2ea90ca5cdf363f56194ead81b0a2c6202@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently if group-id and command-id values are zero we
trigger and collect every RX frame,
this is not the right behavior and zero value
should be handled like any other filter.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 3ed34fbf9d ("iwlwifi: dbg_ini: support FW response/notification region type")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.6a0aae2c0507.I7bd72968279d586af420472707d53106b35efc08@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add an option for adding a PASN responder, specifying the HLTK and
TK (if not associated). When a receiving a range request for a
PASN responder, the driver will ask for a secured measurement with
the specified HLTK and TK.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.28c5f5266000.I2d58b72ff92c47ac33a6aacc27fbf3790b6dfc51@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For secure ranging with an associated station, the driver only needs
to set the HLTK. There is no need to add an internal station for PMF
since the FW will use the existing station which already has the TK
installed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fcebaa5c9bc8.Ic584cc47fee717d0bdb43965798dbdf45d89910a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The overcome instabilities in the RTT results add smoothing logic
to the reported results. In short, the smoothing logic tracks the
RTT average of each responder for a period of time, and in case
a new RTT results is found to be a spur, the tracked RTT average
is reported instead of the current RTT measurement.
Smooth logic debug configuration using iwl-dbg-cfg.ini:
- MVM_FTM_INITIATOR_ENABLE_SMOOTH: Set to 1 to enable smoothing logic
(default=0).
- MVM_FTM_INITIATOR_SMOOTH_ALPHA: A value between 0 - 100, defining
the weight of the current RTT results vs. the RTT average tracked
based on the previous results. A value of 100 means use only the
current RTT results.
- MVM_FTM_INITIATOR_SMOOTH_AGE_SEC: The maximal time in seconds in which
the RTT average tracked based on previous results is considered valid.
- MVM_FTM_INITIATOR_SMOOTH_UNDERSHOOT: if the current RTT is positive
and below the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
- MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT: if the current RTT is positive
and above the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.48a9cec2081b.Iaec1e29f738232adfe9e2ea8e9eb9b6ff0323ae1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Version 11 of the range request command adds support for setting
the PN for secure ranging. For now, this is not yet supported.
The same functions that are used for version 9 and 10 are also
used for version 11 as the common part is the same.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.6f9ed4140e8c.I046e0d9f6dfaafda9794e5eb2ee1f02fcad2851a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For new APIs this avoids checking every return if it's
IWL_FW_CMD_VER_UNKNOWN (99) or it's lower than the new API value
Done with spatch:
-iwl_fw_lookup_cmd_ver(E1, E2, E3)
+iwl_fw_lookup_cmd_ver(E1, E2, E3, IWL_FW_CMD_VER_UNKNOWN)
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.70bec6eb8008.I6ea78553801d33f7ed10fcd2e4be4ba781fe469a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the new version of the GEO_TX_POWER_LIMIT command.
This new version includes UHB values in the table, but for now, since
we don't have the ACPI values yet, we support the API, but don't set
the extra values.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.3700197ed1ed.Ia53fb9c4b5033683fd426d51a0ddc46fb444c805@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the version number to the iwl_geo_tx_power_profile_cmd structs and
move the union into a common place. Additionally, reuse the code that
sets elements that are at the same place in the struct across
different versions.
While at it remove an unused variable, add a comment and move the v2
specific element setting to inside the if statement. Additionally,
invert the if for slightly more readability.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.23ec241f16cd.I8cd21fc5a2498e820b50e1f49a4cbfe545afe30e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command can support more subbands and CDB, so
it can contain more data than earlier versions. Implement support for
the new version of the command, even though we don't have more data to
write to it yet.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.d709a8f17d1d.I9fa54883667c72dabf6d813c70be77538d9af38d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a common structure to contain all different versions of the
tx_power_cmd instead of making a union of the different structs
everywhere we need them. Also move the common part of these structs
into a separate structure (instead of reusing v3) and leave the
per_chain_restriction part out of the common part, because this will
change in version 6 of the command (which will be added soon).
While at it, rename per_chain_restriction to per_chain to shorten it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.4f0bea9fe077.Ib3b540a8288af32d6fa213448e13f82763f85bc9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On newer hardware, we have the full checksum, so use it to report
CHECKSUM_COMPLETE and avoid the protocol specific hardware parsing.
Note that the hardware already parses/removes the SNAP header, so
we actually literally get what we need to report to the stack, as
we're expected to checksum everything after the L2 header (which
is translated/added by mac80211).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.869e829c815d.I70f374865b0acafc675a8d7959912eeaeb595acf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have the same info in two variables,
If umac_error_event_table is 0, we know that UMAC log is not supported,
so we don't need the support_umac_log field.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.299959eeb47b.Ie1f3eecc06e3620098dda74f674f6409b90fe7fa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Change the iwl_all_tsc_rsc struct to hold a sta_id (__le32) field,
while preserving the union, used in the older version.
- Adjust the use of this command according to the TLV.
Signed-off-by: Dan Halperin <Dan1.Halperin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.8c621903db59.I1cc7afedc0ff2009fe1abf007684339f299b73aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The the driver prevents new Tx from being sent during the remove-station
flow is by invalidating the fw_id_to_mac_id rcu of that station.
However, if there was any Tx still in-flight (tx-cmd was sent but the
ba-notif wasn't received yet) the ba-response to those frames is simply
ignored without actually reclaiming anything. This later causes the
driver to think that that some of the station's queues aren't empty when
in practice they are which causes errors in the station remove flow.
Fix this by performing the tx-reclaim also if the rcu is invalid. any DB
that can't be updated due to this is not very important at this stage
since the station is about to be removed soon anyways.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.72c604b4eda9.I21e75b31a9401870d18747355d4f4305b2fe1db8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a missing break, the management multicast key was installed even
though we don't really support it. Fix that, so mac80211 would know that
it should protect frames in software.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.019a64e96d44.I609a995611ac5286e442cd54f764eaf4a7249ac0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support v2 of regulatory capability flags parsed from the device
NVM. New API support is determined by FW lookup of the MCC update
command resposnse version, where version 6 supports the new API.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.3d47f4e8ab98.I0fdd2ce23166c18284d2a7a624c40f35ea81cbc2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Evaluate the appropriate DSM from ACPI to set ETSI SRD 5.8GHz
channels to passive or disabled, default behaviour is enabled.
Add enums and refactor evaluation of DSM functions for better
readablity and more informative debug prints.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.816130ee75e0.I727a217be7c967a97960b197a816fc053d10c48a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is an issue in the HW DMA engine in the 9000 family of devices
when more than 6 RX queues are used. The issue is that the FW may
hang when IWL_MVM_RXQ_NSSN_SYNC notifications are sent.
Fix this by limiting the number of RX queues to 6 in the 9000 family
of devices.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.37d90f9ceb0c.I8dfe8a7d3a7ac9f0bc9d93e4a03f8165d8c999d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are reports that 8822CE fails to work rtw88 with "failed to read DBI
register" error. Also I have a system with 8723DE which freezes the whole
system when the rtw88 is probing the device.
According to [1], platform firmware may not properly power manage the
device during shutdown. I did some expirements and putting the device to
D3 can workaround the issue.
So let's power cycle the device by putting the device to D3 at shutdown
to prevent the issue from happening.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411#c9
BugLink: https://bugs.launchpad.net/bugs/1872984
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200928165508.20775-1-kai.heng.feng@canonical.com
rtl_lps_enter() and rtl_lps_leave() are using in_interrupt() to detect
whether it is safe to acquire a mutex or if it is required to defer to a
workqueue.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
in_interrupt() also is only partially correct because it fails to chose the
correct code path when just preemption or interrupts are disabled.
Add an argument 'may_block' to both functions and adjust the callers to
pass the context information.
The following call chains were analyzed to be safe to block:
rtl_watchdog_wq_callback()
rlf_lps_leave/enter()
rtl_op_suspend()
rtl_lps_leave()
rtl_op_bss_info_changed()
rtl_lps_leave()
rtl_op_sw_scan_start()
rtl_lps_leave()
The following call chains were analyzed to be unsafe to block:
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
setup_special_tx()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_tx_isr
rtl_lps_leave()
halbtc_leave_lps()
rtl_lps_leave()
This leaves four callers of rtl_lps_enter/leave() where the analyzis
stopped dead in the maze of several nested pointer based callchains and
lack of rtlwifi hardware to debug this via tracing:
halbtc_leave_lps(), halbtc_enter_lps(), halbtc_normal_lps(),
halbtc_pre_normal_lps()
These four have been cautionally marked to be unable to block which is the
safe option, but the rtwifi wizards should be able to clarify that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers in is phased out.
rtl_dbg() a printk based debug aid is using in_interrupt() in the
underlying C function _rtl_dbg_out() which is almost identical to
_rtl_dbg_print(). The only difference is the printout of in_interrupt().
The decoding of in_interrupt() as hexvalue is non-trivial and aside of
being phased out for driver usage the return value is just by chance the
masked preempt count value and not a boolean.
These home brewn printk debug aids are tedious to work with and provide
only minimal context. They should be replaced by trace_printk() or a debug
tracepoint which automatically records all context information.
To make progress on the in_interrupt() cleanup, make rtl_dbg() use
_rtl_dbg_print() and remove _rtl_dbg_out().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
INIT_DELAYED_WORK() takes two arguments: A pointer to the delayed work and
a function reference for the callback.
The rtl code casts all function references to (void *) because the
callbacks in use are not matching the required function signature. That's
error prone and bad pratice.
Some of the callback functions are also global, but only used in a single
file.
Clean the mess up by:
- Adding the proper arguments to the callback functions and using them in
the container_of() constructs correctly which removes the hideous
container_of_dwork_rtl() macro as well.
- Removing the type cast at the initializers
- Making the unnecessary global functions static
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
libertas uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug macro prints (INT) when in_interrupt() returns true. The value of
this information is dubious as it does not distinguish between the various
contexts which are covered by in_interrupt().
As the usage of in_interrupt() in drivers is phased out and the same
information can be more precisely obtained with tracing, remove the
in_interrupt() conditional from this debug printk.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
mwifiex uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
hfa384x_cmd() and prism2_hw_reset() check in_interrupt() at function entry
and if true emit a printk at debug loglevel and return. This is clearly debug
code.
Both functions invoke functions which can sleep. These functions already
have appropriate debug checks which cover all invalid contexts, while
in_interrupt() fails to detect context which just has preemption or
interrupts disabled.
Remove both checks as they are incomplete, debug only and already covered
by the subsequently invoked functions properly. If called from invalid
context the resulting back trace is definitely more helpful to analyze the
problem than a printk at debug loglevel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt) in driver code is phased out.
The iwlwifi_dbg tracepoint records in_interrupt() seperately, but that's
superfluous because the trace header already records all kind of state and
context information like hardirq status, softirq status, preemption count
etc.
Aside of that the recording of in_interrupt() as boolean does not allow to
distinguish between the possible contexts (hard interrupt, soft interrupt,
bottom half disabled) while the trace header gives precise information.
Remove the duplicate information from the tracepoint and fixup the caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Luca Coelho <luca@coelho.fi>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out.
The debugging macros in these drivers use in_interrupt() to print 'I' or
'U' depending on the return value of in_interrupt(). While 'U' is confusing
at best and 'I' is not really describing the actual context (hard interupt,
soft interrupt, bottom half disabled section) these debug macros originate
from the pre ftrace kernel era and their value today is questionable. They
probably should be removed completely.
The macros weere added initially for ipw2100 and then spreaded when the
driver was forked.
Remove the in_interrupt() usage at least..
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
brcmf_fweh_process_event() uses in_interrupt() to select the allocation
mode GFP_KERNEL/GFP_ATOMIC. Aside of the above reasons this check is
incomplete as it cannot detect contexts which just have preemption or
interrupts disabled.
All callchains leading to brcmf_fweh_process_event() can clearly identify
the calling context. Convey a 'gfp' argument through the callchains and let
the callers hand in the appropriate GFP mode.
This has also the advantage that any change of execution context or
preemption/interrupt state in these callchains will be detected by the
memory allocator for all GFP_KERNEL allocations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcrmgf_netif_rx() uses in_interrupt to chose between netif_rx() and
netif_rx_ni(). in_interrupt() usage in drivers is phased out.
Convey the execution mode via an 'inirq' argument through the various
callchains leading to brcmf_netif_rx():
brcmf_pcie_isr_thread() <- Task context
brcmf_proto_msgbuf_rx_trigger()
brcmf_msgbuf_process_rx()
brcmf_msgbuf_process_msgtype()
brcmf_msgbuf_process_rx_complete()
brcmf_netif_mon_rx()
brcmf_netif_rx(isirq = false)
brcmf_netif_rx(isirq = false)
brcmf_sdio_readframes() <- Task context sdio_claim_host() might sleep
brcmf_rx_frame(isirq = false)
brcmf_sdio_rxglom() <- Task context sdio_claim_host() might sleep
brcmf_rx_frame(isirq = false)
brcmf_usb_rx_complete() <- Interrupt context
brcmf_rx_frame(isirq = true)
brcmf_rx_frame()
brcmf_proto_rxreorder()
brcmf_proto_bcdc_rxreorder()
brcmf_fws_rxreorder()
brcmf_netif_rx()
brcmf_netif_rx()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
brcmf_sdio_isr() is using in_interrupt() to distinguish if it is called
from a interrupt service routine or from a worker thread.
Passing such information from the calling context is preferred and
requested by Linus, so add an argument `in_isr' to brcmf_sdio_isr() and let
the callers pass the information about the calling context.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and
a tree wide effort to clean up and consolidate the (ab)usage of
in_interrupt() and related checks is happening.
handle_regs_int() is always invoked as part of URB callback which is either
invoked from hard or soft interrupt context.
Remove the magic assertion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[876.898735] ath11k_pci 0000:06:00.0: Unknown eventid: 0x16005
[879.283250] ath11k_pci 0000:06:00.0: Unknown eventid: 0x1d00a
No functional changes. Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600948691-6901-1-git-send-email-govinds@codeaurora.org
This addresses the following gcc warning with "make W=1":
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1331:18: warning:
‘ar9580_1p0_pcie_phy_clkreq_enable_L1’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1338:18: warning:
‘ar9580_1p0_pcie_phy_clkreq_disable_L1’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1345:18: warning:
‘ar9580_1p0_pcie_phy_pll_on_clkreq’ defined but not used [-Wunused-const-variable=]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600831531-8573-1-git-send-email-liheng40@huawei.com
In wl3501_detach(), link->priv is checked for a NULL value before being
passed to free_netdev(). However, it cannot be NULL at this point as it
has already been passed to other functions, so just remove the check.
Addresses-Coverity: CID 710499: Null pointer dereferences (REVERSE_INULL)
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200926174558.9436-1-alex.dewar90@gmail.com
Currently if an unsupported iftype is detected the error return path
does not free the cmd_skb leading to a resource leak. Fix this by
free'ing cmd_skb.
Addresses-Coverity: ("Resource leak")
Fixes: 805b28c05c ("qtnfmac: prepare for AP_VLAN interface type support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925132224.21638-1-colin.king@canonical.com
In the transmit power table, it is important to know what the regulatory
currently is. For different regulatories, there are different
transmit power limits. Show which regulatory the driver is currently
using.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-6-tehuang@realtek.com
This patch adds a function which is able to dump firmware fifo when
firmware crashes. If firmware needs more than one time to dump all logs,
it will set a bit called "more bit" in the header of the first log, and
driver needs to set a register to inform firmware that it is ready for the
next dump.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-5-tehuang@realtek.com
Rtw88 currently has a function to dump reserved page section of the
firmware fifo. Reserved page is just part of the firmware fifo, there
are multiple sections in the firmware fifo for different usages, such as
firmware rx fifo and tx fifo.
This commit adds a function to check not only the reserved page section
but also other parts of the firmware fifo. In addition, we need to dump
firmware fifo to dump the debug log message if firmware crashes.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-4-tehuang@realtek.com
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise S1G Capabilities and channels to mac80211.
Requires a few fixups to account for missing
sband->bitrates, and a custom regulatory db to actually
enable the S1G channels.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-18-thomas@adapt-ip.com
[small code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G beacons are different from normal management beacons, so write
the timestamp to the correct location there.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-17-thomas@adapt-ip.com
[rewrite commit message that was not useful after patch reordering]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfbhn8AAoJEG4XJFUm622bFnMH/jI1Q+DXi2/sn3L01onNABqE
0M/HiZj/Gli2kYrIFiXKzCCVZBA/5CIZefh8Q+brsH4ZonJriTJ/VnJcGdDU68FK
ZqWSAkJ6+pJSaq7O/LofoTw+G0N64GPVN88ZqDMSoCyS8LDsE2QSjX6WEdeX7i9t
BWLcdXJ/brPzxtoH43c+w05syM+NCzPACUEKADa0KU5pg+MKHqtL/2FN8CecyU8k
ylzwH7w99mLBU3dDi8Q+EcUzOa0E+B7h56+BCcy/opCPZl0u2KGKcX/bRib1BwIB
wAChlEppwK/x8G8ViqxkrDVn1IiY2mnlFvdExuOlWqmVqwcccY8lEe19iAnzrV4=
=Xrmx
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild bot reported than link fails when CONFIG_ATH11K_DEBUGFS is disabled:
drivers/net/wireless/ath/ath11k/dp_rx.c:1662: undefined reference to `ath11k_debugfs_htt_ext_stats_handler'
This was because I had missed to move the static inline version of the function
(which are used when CONFIG_ATH11K_DEBUGFS is disabled) to debufs_htt_stats.h.
Also move ath11k_debugfs_htt_stats_req() at the same time. And create a stub
also for ath11k_debugfs_htt_stats_init() for consistency, even if it's not
needed.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 568f06036e ("ath11k: debugfs: move some function declarations to correct header files")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601024241-16594-1-git-send-email-kvalo@codeaurora.org
Remove A-MSDU max_tx_fragments constraint for sdio since the check is
already performed in mt7663s_tx_run_queue routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a missing offchannel condition for channel switch reason, which
bypasses DPD calibration to reduce scanning time.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes variable types in mt76x02_dfs_create_sequence and
mt76x02_dfs_add_event_to_sequence
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release mcu message memory in case of failure in mt7915_mcu_add_beacon
routine
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Taking the same approach as initvals_phy.h.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:218:35: warning: ‘mt76x0_dcoc_tab’ defined but not used [-Wunused-const-variable=]
218 | static const struct mt76_reg_pair mt76x0_dcoc_tab[] = {
| ^~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:86:35: warning: ‘mt76x0_bbp_init_tab’ defined but not used [-Wunused-const-variable=]
86 | static const struct mt76_reg_pair mt76x0_bbp_init_tab[] = {
| ^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:48:35: warning: ‘mt76x0_mac_reg_table’ defined but not used [-Wunused-const-variable=]
48 | static const struct mt76_reg_pair mt76x0_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt76x0/initvals.h:14:35: warning: ‘common_mac_reg_table’ defined but not used [-Wunused-const-variable=]
14 | static const struct mt76_reg_pair common_mac_reg_table[] = {
| ^~~~~~~~~~~~~~~~~~~~
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unlock dfs channels for mt7615 devices since the driver supports
radar detection. Dfs pattern detector has been tested successfully by
mt7615 users.
Do not unlock DFS frequencies for mt7663 devices since it has not been
tested yet.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid using stale isr values, check return value from
sdio_readsb() in mt7663s_rx_work()
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce sdio tx aggregation to reduce bus transaction ands improve tx
throughput. For the moment the skb are copied in a dedicated buffer
since mmc APIs do not support sg table for zero-copy.
Since skb data are already copied in xmit_buff[], avoid linearization in
ma80211 layer. Relying on tx aggregation, we improve tx tpt of ~65%.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Look just at reported quota since the hw sporadically reports mcu tx
quota without setting WHIER_TX_DONE_INT_EN bit
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move frame pad computation out of mt76_skb_adjust_pad routine.
This is a preliminary patch to introduce sdio tx aggregation.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce sdio tx aggregation
Tested-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to not update the available quota in case of a tx error, split
mt7663s_tx_update_sched in mt7663s_tx_{pick,update}_quota routines
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the sdio engine does not report quota for altx queue, move
ctl/mgmt traffic to standard data queues
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set poll timeout to 3s for mt7622 devices in order to avoid fw hangs.
Swap mt7622_trigger_hif_int and doorbell configuration order in
mt7615_mcu_drv_pmctrl routine.
Introduce mt7615_mcu_lp_drv_pmctrl routine to take care of drv_own
configuration for runtime-pm.
Fixes: 08523a2a1d ("mt76: mt7615: add mt7615_pm_wake utility routine")
Fixes: 894b7767ec ("mt76: mt7615: improve mt7615_driver_own reliability")
Fixes: 757b0e7fd6 ("mt76: mt7615: avoid polling in fw_own for mt7663")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MCU field should contain a boolean 0/1, not the flag itself.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt7615/testmode.c: In function mt7615_tm_set_tx_power
drivers/net/wireless/mediatek/mt76/mt7615/testmode.c:83:7: warning: variable ‘index’ set but not used [-Wunused-but-set-variable]=
commit 4f0bce1c88 ("mt76: mt7615: implement testmode support")
involved this unused variable, remove it.
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the switch to using AQL by default, mtxq->retry_q is never filled anymore
Remove it to get rid of a few more unnecessary cycles in the tx path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Compared to mac80211 ACs, MT7915 queue numbers are in reverse order
There is no need for the defensive WARN_ON_ONCE, so we can simplify
the function to avoid the array lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This improves performance by allowing the scheduler to move the tx scheduling
work to idle CPUs. Since tx scheduling work is very latency sensitive and
kept short via AQL, sched_set_fifo_low is used to keep worker priority above
normal tasks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid keeping work like tx scheduling pinned to the CPU it was
scheduled from, it makes sense to switch from tasklets to kernel threads.
Unlike a workqueue, this one only allows one fixed worker function to be
executed by the worker thread. Because of that, there is less locking
and less code for scheduling involved.
This is important because the tx worker is scheduled often in a hot path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not alter the tx/rx chain settings during channel setup, antennas are
remapped by the testmode specific register writes already
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoid firmware falling into spectrum mode since that will set
unexpected PSE/PLE thresholds which lead to Tx hang.
This mode should be cleaned before firmware download stage.
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some devices using MT7628 or MT7603 have only one antenna chain connected.
Detect these using the EEPROM rx/tx path settings
Reported-by: Qin Wei <me@vonger.cn>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On 7615 and newer, DMA completion only triggers unmap, but not free of queued
skbs, since pointers to packets are queued internally.
Because of that, there is no need to process the main data queue immediately
on DMA completion.
To improve performance, mask out the DMA data queue completion interrupt and
process the queue only when we receive a txfree event.
This brings the number of interrupts under load down to a small fraction.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous scheduling round may have been limited by AQL.
More frames might be available after the tx free run.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tx cleanup and tx enqueuing can run in parallel. In order to avoid queue
starvation issues under load, update q->queued immediately.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since DMA completion does not imply tx completion, it makes more sense to
poll for airtime from mt7915_mac_tx_free.
Reduce the runtime of the function by moving all items from dev->sta_poll_list
to a local list once and process any stations that were added afterwards
on the next run
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- change the WTBL LMAC access function to set the mapping window only once
- use ac * 2 as offset, since each AC has separate words for rx and tx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix length field corruption in usb dma header introduced adding sdio
support
Fixes: 75b10f0cbd ("mt76: mt76u: add mt76_skb_adjust_pad utility routine")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a possible NULL pointer dereference in mt76_testmode_dump() since
nla_nest_start returns NULL in case of error
Fixes: f0efa86215 ("mt76: add API for testmode support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize wcid to global_wcid if msta is NULL in mt7615_pm_wake_work
routine since wcid will be dereferenced running mt76_tx()
Fixes: 2b8cdfb28d ("mt76: mt7615: wake device before pushing frames in mt7615_tx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a memory leak in mt7615_tm_set_tx_power routine if
mt7615_eeprom_get_target_power_index fails.
Moreover do not account req_header twice in mcu skb allocation.
Fixes: 4f0bce1c88 ("mt76: mt7615: implement testmode support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7663s have to rely on MMC_PM_KEEP_POWER in pm_flags for to avoid SDIO
power is being shut off.
To fix sdio access failure like "mt7663s mmc1:0001:1: sdio write failed:
-22" for the first sdio command to access the bus in the resume handler.
Fixes: a66cbdd657 ("mt76: mt7615: introduce mt7663s support")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warnings in mt7663s driver:
drivers/net/wireless/mediatek/mt76/mt7615/sdio_mcu.c:78:62: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_mcu.c:110:62: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_txrx.c:229:64: warning:
Using plain integer as NULL pointer
drivers/net/wireless/mediatek/mt76/mt7615/sdio_txrx.c:263:64: warning:
Using plain integer as NULL pointer
Fixes: a66cbdd657 ("mt76: mt7615: introduce mt7663s support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce scope of mutex_acquire/mutex_release in mt7615_reset_test_set
routine in order to fix the following static checker warning:
drivers/net/wireless/mediatek/mt76/mt7615/debugfs.c:179
mt7615_reset_test_set()
warn: inconsistent returns 'dev->mt76.mutex'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ea4906c4be ("mt76: mt7615: wake device before accessing regmap in debugfs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This disables the software A-MSDU aggregation in mac80211 and enables hardware
offloading
Suggested-by: Yiwei Chung <yiwei.chung@mediatek.com>
Suggested-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the txwi data as primary source information to avoid touching skb data
Use bitfield instead of state variable + spinlock
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615 and newer drivers do not need this, since they use sequence number offload
Moving this code also reduces the number of callsites to make it easier to review
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Queueing a per-sta work item from the tx free path can become very expensive
under load. This work is only supposed to pull rate control stats every
second and deal with rate control changes.
Additionally, the rate control update code was wrong, because it was
confusing bit masks and bit numbers in test_bit.
Fix this by introducing a dedicated device work item for rate control
updates, and by polling station stats from the phy mac work.
Stations requiring polling or rate control updates are added to lists
protected by dev->sta_poll_lock.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only clear unmasked interrupts. If an interrupt is temporarily masked,
its pending events need to be processed later, even if another interrupt
happened in the mean time.
Disable interrupts in one call before scheduling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If an interrupt is temporarily masked, its pending events need to be processed
later, even if another interrupt happened in the mean time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only clear unmasked interrupts. If an interrupt is temporarily masked,
its pending events need to be processed later, even if another interrupt
happened in the mean time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A small part of the first skb buffer is passed to the firmware for parsing
via DMA, while the full buffer is passed as part of the TXP.
Avoid calling DMA unmap on the first part (with a different length than map)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to maximize parallelism, split status work in tx status work
and rx net work
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As it has been done for tx and rx processing, move tx/rx status
processing into mt76s_txrx_wq workqueue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move rx processing to mt76s_txrx_wq in order to minimize the interval when
the sdio bus is locked during rx
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76s_txrx_wq workqueue and move tx processing from kthread to
a dedicated work. This is preliminary patch to improve mt7663s throughput
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free the mcu skb in case of error in mt76s_tx_queue_skb_raw routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reschedule runtime-pm after receiving a tx interrupt.
Update runtime-pm last activity before injecting packets
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not tx packets in mt76_txq_send_burst() or mt76_txq_schedule_list()
if the device is in runtime-pm
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
wq queue is always updated holding mt76 spinlock. Grab mt76 lock in
mt7615_queue_key_update() before putting a new element at the end of the
queue.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize set_drv_ctrl and set_fw_ctrl function pointers in
mt7663s_mcu_init. This is a preliminary patch to enable runtime-pm for
mt7663s chipset.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce set_drv_ctrl and set_fw_ctrl function pointers in
mt7615_mcu_ops data structure. This is a preliminary patch to enable
runtime-pm for non-pci chipsets
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_EE_WIFI_CONF field can be used to detect if the chipset is MT7615D.
Thus, add support to automatically register ext_phy if DBDC is detected.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If rtw_core_init() fails to load the wow firmware, rtw_core_deinit()
will not get called to clean up the regular firmware.
Ensure that an error loading the wow firmware does not produce an oops
for the regular firmware by waiting on its completion to be signalled
before returning. Also release the loaded firmware.
Fixes: c8e5695eae ("rtw88: load wowlan firmware if wowlan is supported")
Cc: Chin-Yen Lee <timlee@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200920132621.26468-3-afaerber@suse.de
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1576:6: warning:
variable 'ret' set but not used [-Wunused-but-set-variable]
1576 | int ret;
| ^~~
driver_for_each_device() has been declared with __must_check, so the
return value should be checked.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600481191-14250-1-git-send-email-zhangchangzhong@huawei.com
After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200923052442.24141-1-nbd@nbd.name
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "tsid" is a user controlled u8 which comes from debugfs. Values
more than 15 are invalid because "active_tsids" is a 16 bit variable.
If the value of "tsid" is more than 31 then that leads to a shift
wrapping bug.
Fixes: 8fffd9e5ec ("ath6kl: Implement support for QOS-enable and QOS-disable from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918142732.GA909725@mwanda
There were two asignments to num_keep_alive_pattern, remove the first one which is wrong.
No functional changes. Compile tested only.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600361190-22047-1-git-send-email-kvalo@codeaurora.org
In commit 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params") the
wmi config initialisation was moved to hw_ops->wmi_init_config() but the old
initialisation values were accidentally left to ath11k_wmi_cmd_init(). This
is very confusing, so remove the redundant values.
And this was actually so confusing that in commit aa2092a9ba ("ath11k: add
raw mode and software crypto support") I actually it caused a bug: when
ATH11K_FLAG_RAW_MODE was enabled rx_decap_mode was assigned back to
TARGET_DECAP_MODE_NATIVE_WIFI in ath11k_init_wmi_config_ipq8074(). Fix this at
the same time.
Compile tested only.
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600356507-29237-1-git-send-email-kvalo@codeaurora.org
IPQ6018 supported with 4 bytes FFT BIN size. so supported 4 bytes
parsing logic in FFT report process. since spectral_fft_sz is
configured as zero in hw_params, spectral is not supported in
QCA6390 platform.
Tested-on: IPQ6018 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600236776-4042-1-git-send-email-periyasa@codeaurora.org
Some of the function declarations are for functions in debugfs_htt_stats.c and
debugfs_sta.c, move them to corresponding header files. As debugfs_sta.h didn't
exist create it.
Also in debugfs_htt_stats.h move dunction declarations to the end of the file.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-4-git-send-email-kvalo@codeaurora.org
If CONFIG_ATH11K_DEBUGFS is disabled there are warnings debug.c:
drivers/net/wireless/ath/ath11k/debug.c:36:20: warning: 'htt_bp_lmac_ring' defined but not used [-Wunused-variable]
36 | static const char *htt_bp_lmac_ring[HTT_SW_LMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/debug.c:15:20: warning: 'htt_bp_umac_ring' defined but not used [-Wunused-variable]
15 | static const char *htt_bp_umac_ring[HTT_SW_UMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
Fix this by refactoring debugfs code to debugfs.c. This also reduces the number
of ifdefs in debug.c and makes it easier to maintain the code.
No functional changes. Compile tested only.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-1-git-send-email-kvalo@codeaurora.org
Return value form wait_for_completion_timeout should to be checked.
This is detected by Coverity: #CID:1464479 (CHECKED_RETURN)
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200621095136.7xdbzkthoxuw2qow@debian.debian-2
This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
In order to get 802.11ac working the way we want, additional parameters
need to be passed down to the firmware.
This patch takes the full remaining set of parameters defined in the
downstream riva/inc/wlan_hal_cfg.h and imports them into hal.h with some
minor name length adjustments.
This addition will allow us to pass a larger firmware configuration set
later on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-2-bryan.odonoghue@linaro.org
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
This commit encodes the 802.11ac PHY mode for a given channel in the upper
bits of the hw_value field. This allows for a neat read-out and application
of the relevant PHY setting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
Adds HW_VALUE_PHY(hw_value) an access macro that will be used to
extract a hardware specific PHY setting for a given channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-4-bryan.odonoghue@linaro.org
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to
extract the channel number from struct ieee80211_channel->hw_value in
preparation for also storing PHY settings for 802.11ac in the upper bits of
hw_value.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-2-bryan.odonoghue@linaro.org
Board Data File (BDF) is loaded upon driver boot-up procedure.
The right board data file is identified using bus and qmi-board-id.
The problem, however, can occur when the (default) board data
file cannot fulfill with the vendor requirements and it is
necessary to use a different board data file.
Also using the chip_id for identifying the board data helps
in dealing with different variants of the board data file based
on the RF card. If the chip_id is not programmed, a default value
of 0xff will be used for parsing the board data file.
Add the support to get the variant field from DTSI and
use this information along with the chip_id to load the vendor
specific BDF.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v2";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v1";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=snoc,qmi-board-id=16,qmi-chip-id=0,variant=xyz-v1
* bus=snoc,qmi-board-id=17,qmi-chip-id=0,variant=xyz-v2
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600157948-2042-1-git-send-email-pillair@codeaurora.org
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1155:27-47: WARNING:
Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1156:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:1159:3-23: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074437.3459305-1-yanaijie@huawei.com
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2680:27-47: WARNING:
Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2683:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2686:3-23: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074428.3459234-1-yanaijie@huawei.com
This addresses the following coccinelle warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:721:27-47:
WARNING: Comparison of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:722:3-23: WARNING:
Assignment of 0/1 to bool variable
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/dm.c:725:2-22: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200919074412.3459163-1-yanaijie@huawei.com
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been
designed to operate in standalone fashion. As a result we can drop the
dead code now present in wcn36xx_smd_config_bss() and happily remove one
kzalloc from the BSS config path as we do so.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-8-bryan.odonoghue@linaro.org
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the
version 0 data-path in wcn36xx_smd_config_bss() to use
wcn36xx_smd_config_bss_v0().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-7-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of
functionally decomposing wcn36xx_smd_config_bss().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-6-bryan.odonoghue@linaro.org
This patch updates wcn36xx_smd_config_bss_v1() to update on internally
derived parameters only, specifically making use of STA v1 wrapper routines
previously added.
Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg
which gives us options in later patches to eliminate the kzalloc() in
wcn36xx_smd_config_bss entirely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-5-bryan.odonoghue@linaro.org
This commit moves BSS parameter setup to a separate function
wcn36xx_smd_set_bss_params(). This will allow for further functional
decomposition and fewer kzalloc() operations in subsequent patches.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-4-bryan.odonoghue@linaro.org
In order to facilitate functional decomposition of
wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later
in function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-3-bryan.odonoghue@linaro.org
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly
defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-2-bryan.odonoghue@linaro.org
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which
calls into wcn36xx_smd_set_sta_params() and then subsequently sets
version-1 specific parameters.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-8-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function
is to decide if the BSS is VHT capable and if so set the appropriate bit
in the BSS parameter structure for passing to the firmware.
VHT Channel width set is not set since we don't support 160MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-7-bryan.odonoghue@linaro.org
Adds a routine to allow setting the LDPC bit for HT parameter passing
inside the version 1 STA parameters data structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-6-bryan.odonoghue@linaro.org
This commit adds support for setting VHT parameters based on the declared
VHT capability bits in the VHT capability structure.
We cannot do 160MHz so VHT Channel width set should be zero.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-5-bryan.odonoghue@linaro.org
Toggling the LDPC enabled bit is possible only via the extended V1
data-structure. This function provides a means of setting the default
depending on chip-type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-4-bryan.odonoghue@linaro.org
This commit adds support for setting default VHT parameters, which are
exposed by the extended version 1 STA parameter type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-3-bryan.odonoghue@linaro.org
This patch converts the internal data structure used to store data-rates
from version 0 to version 1.
This allows us to extend out the internal storage to represent VHT
parameters.
Using the extended version 1 data-structure allows us to avoid a whole raft
of version 1 specific fixup functions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-3-bryan.odonoghue@linaro.org
In order to pass VHT parameters to wcn3680 we need to use a super-set of
the V1 data-structures with additional VHT parameters tacked on.
This patch adds the additional fields to the STA and BSS parameter
structures.
Since neither wcn3620 nor wcn3660 support VHT the size of the passed
message is fixed to the previous message length. Subsequent changes will
differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger
message size.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-2-bryan.odonoghue@linaro.org
IPQ8074 HW uses rproc with AHB as underlying hif layer.
Move rproc references from common core layer to target
hif layer. Remove IS_ENABLED check for CONFIG_REMOTEPROC
as it's not required anymore.
No functional changes. Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600090615-18904-1-git-send-email-govinds@codeaurora.org
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/hw.c:861:6-35: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-10-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:566:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:572:13-19: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:581:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:587:13-19: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-9-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:616:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:621:13-19: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:626:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:631:13-19: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-8-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:831:14-49: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-7-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:1816:5-13: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:1825:5-13: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:1839:5-13: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-6-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:1897:5-13: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-5-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:161:14-17: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:168:13-16: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:179:14-17: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/mac.c:186:13-16: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-4-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c:1106:14-18: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-3-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/hw.c:797:6-33: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918102505.16036-2-zhengbin13@huawei.com
The wilc_wfi_init_mon_int() forgets to clean up resource when
register_netdevice() failed. Add the missed call to fix it.
And the return value of netdev_priv can't be NULL, so remove
the unnecessary error handling.
Fixes: 588713006e ("staging: wilc1000: avoid the use of 'wilc_wfi_mon' static variable")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200917123019.206382-1-huangguobin4@huawei.com
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:191:5-13: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:205:5-13: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:211:5-13: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:625:5-30: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910141642.127006-4-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/trx.c:592:5-9: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/trx.c:633:5-9: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910141642.127006-3-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/rf.c:52:5-22: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/rf.c:482:6-14: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910141642.127006-2-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:777:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:782:13-19: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:787:14-20: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:792:13-19: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:871:6-33: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/hw.c:1070:5-13: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910135917.143723-4-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:735:5-9: WARNING: Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:776:5-9: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910135917.143723-3-zhengbin13@huawei.com
Fixes coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1584:14-18: WARNING: Comparison to bool
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910135917.143723-2-zhengbin13@huawei.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_lcn.c:108:18: warning: unused variable 'dot11lcn_gain_tbl_rev1' [-Wunused-const-variable]
static const u32 dot11lcn_gain_tbl_rev1[] = {
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-29-lee.jones@linaro.org
Firmware may have SAE authenticator code built-in. This is detected by
the driver and indicated in the wiphy features flags. User space can use
this flag to determine whether or not to provide the password material
in the nl80211 start AP command to offload the SAE authentication in AP
mode.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817073316.33402-5-stanley.hsu@cypress.com
Firmware may have authenticator code built-in. This is detected by the
driver and indicated in the wiphy features flags. User space can use
this flag to determine whether or not to provide the pre-shared key
material in the nl80211 start AP command to offload the 4-way handshake
in AP mode.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817073316.33402-3-stanley.hsu@cypress.com
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfW5XtAAoJEG4XJFUm622bnuoIAIx8xplr5UYZv/qaMyvBaoNQ
gG7AU3IUs4QibSUabpE7kBpdLVX9O4mC5nLWCutGH1dTrJGIQsnuncW206yOAZPp
+MPOauxBmfkBm61RmJ3beGXan6ZGlE7rwkO0Pf+mqrWk4XVovItKpJUuR+IWliu/
gdVbdC2Uu7bQlv44MI/3xOpx5Xvk5gq/4tPcTOE3b57wIyln0NSKJYOoOuL+i2f/
WDiTgPyA/9x+llrf6sA+oLmEN2F8TpVWSDv6F4mA5E9uYjJrJMEJLosSzohU7+ou
j7gvCMv5F8+XnQYX4T/qJ05axBDQO2zRJ6YynWDoqQss4XW8xaiuQCEmaiHE8GM=
=kS8U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.10. Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.
To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0
To enable software crypto:
insmod ath11k.ko crypto_mode=1
These modes could be helpful in debugging crypto related issues.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com
Drop some bogus Kconfig selects that are not entirely accurate, and
unnecessary to begin with, since the same Kconfig options also select
LIB80211 features that already imply the selected functionality (AES
for CCMP, ARC4 and ECB for TKIP)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp
clang static analyzer reports this problem
init.c:739:8: warning: Called function pointer
is null (null dereference)
ret = adapter->if_ops.check_fw_status( ...
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In mwifiex_dnld_fw, there is an earlier check for check_fw_status(),
The check was introduced for usb support at the same time this
check in _mwifiex_fw_dpc() was made
if (adapter->if_ops.dnld_fw) {
ret = adapter->if_ops.dnld_fw(adapter, &fw);
} else {
ret = mwifiex_dnld_fw(adapter, &fw);
}
And a dnld_fw function initialized as part the usb's
mwifiex_if_ops.
The other instances of mwifiex_if_ops for pci and sdio
both set check_fw_status.
So the first check is not needed and can be removed.
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906200548.18053-1-trix@redhat.com
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com
Add peer max mpdu length configuration support in peer_assoc_he
parameters. Noticed low throughput for the STA which
supports HE, HT and not VHT in MU-MIMO case without this
configuration
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588611900-21185-2-git-send-email-tamizhr@codeaurora.org
There is a success path where "ret" isn't initialized where we never
have a ATH11K_SPECTRAL_TAG_SCAN_SEARCH and then ret isn't initialized.
Fixes: 9d11b7bff9 ("ath11k: add support for spectral scan")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200619142922.GA267142@mwanda
clang static analyzer reports this problem
mac.c:6204:2: warning: Attempt to free released memory
kfree(ar->mac.sbands[NL80211_BAND_2GHZ].channels);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The channels pointer is allocated in ath11k_mac_setup_channels_rates()
When it fails midway, it cleans up the memory it has already allocated.
So the error handling needs to skip freeing the memory.
There is a second problem.
ath11k_mac_setup_channels_rates(), allocates 3 channels. err_free
misses releasing ar->mac.sbands[NL80211_BAND_6GHZ].channels
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906212625.17059-1-trix@redhat.com
Add support to vote for chain-1 voltage regulator
in WCN3990.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593194502-13164-3-git-send-email-pillair@codeaurora.org
Setting F2 block size to 128 bytes for BCM4329 allows to significantly
improve RX throughput on NVIDIA Tegra20. Before this change the throughput
was capped to 30 Mbit/s on Tegra, now throughput is at 40 Mbit/s, which is
a maximum throughput for the BCM4329 chip. The F2 block size is borrowed
from the downstream BCMDHD driver. The comment in the BCMDHD driver says
that 128B improves throughput and turns out that it works for the brcmfmac
as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-4-digetx@gmail.com
The chip ID was already printed out at the time when debug message about
the changed F2 watermark is printed, hence let's drop the unnecessary part
of the debug messages. This cleans code a tad and also allows to re-use
the F2 watermark debug messages by multiple chips.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-3-digetx@gmail.com
This patch fixes SDHCI CRC errors during of RX throughput testing on
BCM4329 chip if SDIO BUS is clocked above 25MHz. In particular the
checksum problem is observed on NVIDIA Tegra20 SoCs. The good watermark
value is borrowed from downstream BCMDHD driver and it's matching to the
value that is already used for the BCM4339 chip, hence let's re-use it
for BCM4329.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200830191439.10017-2-digetx@gmail.com
These variables only used in sdio.c, move them to .c file
can silence these warnings:
In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com
In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
static const u8 tos_to_tid_inv[] = {
^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
^~~~~~~~~~~~~~~~~~~~~~~
move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com
Remove function return type const in rtw8821c_get_swing_index().
This is unused, and unnecessary to be const.
All warnings (new ones prefixed by >>):
>> drivers/net/wireless/realtek/rtw88/rtw8821c.c:71:8: warning: type
qualifiers ignored on function return type [-Wignored-qualifiers]
71 | static const u8 rtw8821c_get_swing_index(struct rtw_dev *rtwdev)
| ^~~~~
Fixes: f745eb9ca5 ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902053402.12839-1-yhchuang@realtek.com
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com
A definition of this macro was kept until all drivers had been converted.
It can now be deleted.
This change also renames _rtl_dbg_trace() to _rtl_dbg_out().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831185046.30307-1-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8821ae. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831184536.29950-1-Larry.Finger@lwfinger.net
In order for the firmware to process extended V1 parameters with the
addtional VHT fields added we need to first enable the feature bit DOT11AC.
Once done the version number in the HAL message header will be acted upon
by the firmware.
Extended V1 parameters are a prerequisite for 802.11ac speeds since we
cannot communicate VHT parameters to the firmware absent the extended data
structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-11-bryan.odonoghue@linaro.org
Two pointers are already defined in this function "bss" and "sta" which
point to fields within msg_body->bss_params.
We can substantially reduce the amount of extraneous text in this function
by making use of those pointers. This change makes the code easier to read
and modify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-10-bryan.odonoghue@linaro.org
Specify the number of spatial streams in ieee80211_rx_status. For non VHT
data-rates the wireless core doesn't care about this field, however for VHT
data-rates it does.
Every version of wcn36xx has one spatial stream, so specify nss for
wcn3620, wcn3660 and wcn3680 now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-7-bryan.odonoghue@linaro.org
The rate_idx is the index of the bitrate in the supported rate table.
However the 5Ghz band has a smaller legacy bitrate table than 2.4Ghz
since it does not have the DSSS bitrates (1, 2, 5.5, 11).
So in 5Ghz band the index should adjusted accrodingly (-4).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[bod: Made sure fix is only applied if the rate_idx > n_bitrates]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-6-bryan.odonoghue@linaro.org
If DT indicates we are dealing with a WCN3680 mark the rf_id field as
RF_IRIS_WCN3680 allowing for further chip-specific logic.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-3-bryan.odonoghue@linaro.org
The WCN3680 has some specific behaviours that we want to capture to
distinguish it from the WCN3620 and WCN3660 respectively.
Add an identifier for this purpose.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-2-bryan.odonoghue@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9218:18: warning: ‘papd_cal_scalars_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9151:18: warning: ‘papd_comp_epsilon_tbl_core1_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9084:18: warning: ‘papd_cal_scalars_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_n.c:9017:18: warning: ‘papd_comp_epsilon_tbl_core0_rev3’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phytbl_lcn.c:1510:33: warning: ‘dot11lcnphytbl_rx_gain_info_rev1’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-30-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:16:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_spurwar_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:19036:6: warning: variable ‘tempval’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_tempsense_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:21983:28: warning: variable ‘RfctrlMiscReg6_save’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_rssi_compute_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:22986:6: warning: variable ‘phyRx0_l’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_runsamples_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23101:6: warning: variable ‘lpf_bw_ctl_miscreg4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23100:50: warning: variable ‘lpf_bw_ctl_miscreg3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_iqcal_gainparams_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:23406:6: warning: variable ‘idx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a2_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24707:7: warning: variable ‘phy_a6’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function ‘wlc_phy_a3_nphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:24999:7: warning: variable ‘phy_a11’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-29-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:11:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_rx_iq_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1366:29: warning: variable ‘RFOverride0_old’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_radio_2064_channel_tune_4313’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:21: warning: variable ‘qFvco’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:14: warning: variable ‘qFref’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1667:6: warning: variable ‘qFxtal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_idle_tssi_est’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2856:6: warning: variable ‘idleTssi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_tx_iqlo_soft_cal_full’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:53: warning: variable ‘locc4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:46: warning: variable ‘locc3’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:39: warning: variable ‘locc2’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3861:32: warning: variable ‘iqcc0’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_lcnphy_periodic_cal’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4196:6: warning: variable ‘rx_iqcomp_sz’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4195:33: warning: variable ‘rx_iqcomp’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4194:16: warning: variable ‘full_cal’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c: In function ‘wlc_phy_txpwr_srom_read_lcnphy’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4919:7: warning: variable ‘opo’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intersil/prism54/isl_ioctl.c: In function ‘prism54_update_stats’:
drivers/net/wireless/intersil/prism54/isl_ioctl.c:166:6: warning: variable ‘j’ set but not used [-Wunused-but-set-variable]
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aurelien Alleaume <slts@free.fr>
Cc: Valerio Riedel <hvr@gnu.org>
Cc: "Luis R. Rodriguez" <mcgrof@ruslug.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:24: warning: Incorrect use of kernel-doc format: * rsi_sdio_master_access_msword() - This function sets the AHB master access
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:32: warning: Function parameter or member 'adapter' not described in 'rsi_sdio_master_access_msword'
drivers/net/wireless/rsi/rsi_91x_sdio_ops.c:32: warning: Function parameter or member 'ms_word' not described in 'rsi_sdio_master_access_msword'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtw88/debug.c: In function ‘rtw_debug_get_mac_page’:
drivers/net/wireless/realtek/rtw88/debug.c:430:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtw88/debug.c: In function ‘rtw_debug_get_bb_page’:
drivers/net/wireless/realtek/rtw88/debug.c:450:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/wl3501_cs.c:57:
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'reg_domain' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:143: warning: Function parameter or member 'channel' not described in 'iw_valid_channel'
drivers/net/wireless/wl3501_cs.c:162: warning: Function parameter or member 'reg_domain' not described in 'iw_default_channel'
drivers/net/wireless/wl3501_cs.c:248: warning: Function parameter or member 'this' not described in 'wl3501_set_to_wla'
drivers/net/wireless/wl3501_cs.c:270: warning: Function parameter or member 'this' not described in 'wl3501_get_from_wla'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'this' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'data' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:467: warning: Function parameter or member 'len' not described in 'wl3501_send_pkt'
drivers/net/wireless/wl3501_cs.c:729: warning: Function parameter or member 'this' not described in 'wl3501_block_interrupt'
drivers/net/wireless/wl3501_cs.c:746: warning: Function parameter or member 'this' not described in 'wl3501_unblock_interrupt'
drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'irq' not described in 'wl3501_interrupt'
drivers/net/wireless/wl3501_cs.c:1124: warning: Function parameter or member 'dev_id' not described in 'wl3501_interrupt'
drivers/net/wireless/wl3501_cs.c:1257: warning: Function parameter or member 'dev' not described in 'wl3501_reset'
drivers/net/wireless/wl3501_cs.c:1420: warning: Function parameter or member 'link' not described in 'wl3501_detach'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Fox Chen <mhchen@golf.ccl.itri.org.tw>
Cc: de Melo <acme@conectiva.com.br>
Cc: Gustavo Niemeyer <niemeyer@conectiva.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/intersil/hostap/hostap_cs.c:196:
drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
1806 | u16 tx_control, fc;
| ^~
In file included from drivers/net/wireless/intersil/hostap/hostap_plx.c:264:
drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
1806 | u16 tx_control, fc;
| ^~
In file included from drivers/net/wireless/intersil/hostap/hostap_pci.c:221:
drivers/net/wireless/intersil/hostap/hostap_hw.c: In function ‘prism2_tx_80211’:
drivers/net/wireless/intersil/hostap/hostap_hw.c:1806:18: warning: variable ‘fc’ set but not used [-Wunused-but-set-variable]
1806 | u16 tx_control, fc;
| ^~
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-20-lee.jones@linaro.org
- File headers do not make for good kernel-doc candidates
- Kernel-doc header lines should start with " *"
- Fix doc-rot issue
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_sdio.c:25: warning: cannot understand function prototype: 'u16 dev_oper_mode = DEV_OPMODE_STA_BT_DUAL; '
drivers/net/wireless/rsi/rsi_91x_sdio.c:802: warning: bad line: from the device.
drivers/net/wireless/rsi/rsi_91x_sdio.c:842: warning: Function parameter or member 'pfunction' not described in 'rsi_init_sdio_interface'
drivers/net/wireless/rsi/rsi_91x_sdio.c:842: warning: Excess function parameter 'pkt' description in 'rsi_init_sdio_interface'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-17-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'name' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'requested_packet' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'suppr_transit_count' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'send_tim_signal' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_pending_bmp' not described in 'brcmf_fws_mac_descriptor'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:389: warning: Function parameter or member 'traffic_lastreported_bmp' not described in 'brcmf_fws_mac_descriptor'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'status' not described in 'zd_rx_rate'
drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Excess function parameter 'rx_status' description in 'zd_rx_rate'
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'hw' not described in 'zd_mac_tx_status'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'skb' not described in 'zd_mac_tx_status'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Function parameter or member 'tx_status' not described in 'zd_mac_tx_status'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:433: warning: Excess function parameter 'flags' description in 'zd_mac_tx_status'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:487: warning: Function parameter or member 'urb' not described in 'zd_mac_tx_failed'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:487: warning: Excess function parameter 'dev' description in 'zd_mac_tx_failed'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:927: warning: Function parameter or member 'hw' not described in 'zd_op_tx'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:927: warning: Excess function parameter 'dev' description in 'zd_op_tx'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:963: warning: Function parameter or member 'hw' not described in 'filter_ack'
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:963: warning: Excess function parameter 'dev' description in 'filter_ack'
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Michael Wu <flamingice@sourmilk.net>
Cc: "Luis R. Rodriguez" <mcgrof@winlab.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-11-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'rx_frame' not described in 'zd_rx_rate'
drivers/net/wireless/zydas/zd1211rw/zd_chip.c:1385: warning: Function parameter or member 'status' not described in 'zd_rx_rate'
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:12:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c: In function ‘wlc_phy_upd_env_txpwr_rate_limits’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:11: warning: variable ‘vbat’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_cmn.c:1516:5: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:434: warning: Function parameter or member 'upriv' not described in 'ezusb_req_queue_run'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'req' not described in 'ezusb_fill_req'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'length' not described in 'ezusb_fill_req'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'rid' not described in 'ezusb_fill_req'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'data' not described in 'ezusb_fill_req'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'frame_type' not described in 'ezusb_fill_req'
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:716: warning: Function parameter or member 'reply_count' not described in 'ezusb_fill_req'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-8-lee.jones@linaro.org
Most likely caused by doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2048: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-7-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/3945.c:104: warning: Function parameter or member 'il' not described in 'il3945_disable_events'
drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'il' not described in 'il3945_tx_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'txq_id' not described in 'il3945_tx_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/3945.c:273: warning: Function parameter or member 'idx' not described in 'il3945_tx_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/3945.c:299: warning: Function parameter or member 'il' not described in 'il3945_hdl_tx'
drivers/net/wireless/intel/iwlegacy/3945.c:299: warning: Function parameter or member 'rxb' not described in 'il3945_hdl_tx'
drivers/net/wireless/intel/iwlegacy/3945.c:637: warning: Function parameter or member 'il' not described in 'il3945_hw_txq_free_tfd'
drivers/net/wireless/intel/iwlegacy/3945.c:637: warning: Function parameter or member 'txq' not described in 'il3945_hw_txq_free_tfd'
drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'il' not described in 'il3945_hw_build_tx_cmd_rate'
drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'cmd' not described in 'il3945_hw_build_tx_cmd_rate'
drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'info' not described in 'il3945_hw_build_tx_cmd_rate'
drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'hdr' not described in 'il3945_hw_build_tx_cmd_rate'
drivers/net/wireless/intel/iwlegacy/3945.c:686: warning: Function parameter or member 'sta_id' not described in 'il3945_hw_build_tx_cmd_rate'
drivers/net/wireless/intel/iwlegacy/3945.c:838: warning: Function parameter or member 'il' not described in 'il3945_txq_ctx_reset'
drivers/net/wireless/intel/iwlegacy/3945.c:1003: warning: Function parameter or member 'il' not described in 'il3945_hw_txq_ctx_free'
drivers/net/wireless/intel/iwlegacy/3945.c:1044: warning: Function parameter or member 'new_reading' not described in 'il3945_hw_reg_adjust_power_by_temp'
drivers/net/wireless/intel/iwlegacy/3945.c:1044: warning: Function parameter or member 'old_reading' not described in 'il3945_hw_reg_adjust_power_by_temp'
drivers/net/wireless/intel/iwlegacy/3945.c:1053: warning: Function parameter or member 'temperature' not described in 'il3945_hw_reg_temp_out_of_range'
drivers/net/wireless/intel/iwlegacy/3945.c:1069: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_txpower_get_temperature'
drivers/net/wireless/intel/iwlegacy/3945.c:1107: warning: Function parameter or member 'il' not described in 'il3945_is_temp_calib_needed'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'scan_tbl_idx' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'rate_idx' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'clip_pwrs' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1328: warning: Function parameter or member 'band_idx' not described in 'il3945_hw_reg_set_scan_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1383: warning: Function parameter or member 'il' not described in 'il3945_send_tx_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1460: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_set_new_power'
drivers/net/wireless/intel/iwlegacy/3945.c:1522: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_get_ch_txpower_limit'
drivers/net/wireless/intel/iwlegacy/3945.c:1552: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_comp_txpower_temp'
drivers/net/wireless/intel/iwlegacy/3945.c:1712: warning: Function parameter or member 'il' not described in 'il3945_commit_rxon'
drivers/net/wireless/intel/iwlegacy/3945.c:1845: warning: Function parameter or member 'il' not described in 'il3945_reg_txpower_periodic'
drivers/net/wireless/intel/iwlegacy/3945.c:1889: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_get_ch_grp_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:1889: warning: Function parameter or member 'ch_info' not described in 'il3945_hw_reg_get_ch_grp_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'il' not described in 'il3945_hw_reg_get_matched_power_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'requested_power' not described in 'il3945_hw_reg_get_matched_power_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'setting_idx' not described in 'il3945_hw_reg_get_matched_power_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:1924: warning: Function parameter or member 'new_idx' not described in 'il3945_hw_reg_get_matched_power_idx'
drivers/net/wireless/intel/iwlegacy/3945.c:2055: warning: Function parameter or member 'il' not described in 'il3945_txpower_set_from_eeprom'
drivers/net/wireless/intel/iwlegacy/3945.c:2313: warning: Function parameter or member 'il' not described in 'il3945_init_hw_rate_table'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/3945-rs.c:136: warning: Function parameter or member 'rs_sta' not described in 'il3945_rate_scale_flush_wins'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'rs_sta' not described in 'il3945_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'win' not described in 'il3945_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'success' not described in 'il3945_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'retries' not described in 'il3945_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:243: warning: Function parameter or member 'idx' not described in 'il3945_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'il_rate' not described in 'il3945_rs_tx_status'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'sband' not described in 'il3945_rs_tx_status'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'sta' not described in 'il3945_rs_tx_status'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'il_sta' not described in 'il3945_rs_tx_status'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:429: warning: Function parameter or member 'skb' not described in 'il3945_rs_tx_status'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'il_r' not described in 'il3945_rs_get_rate'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'sta' not described in 'il3945_rs_get_rate'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'il_sta' not described in 'il3945_rs_get_rate'
drivers/net/wireless/intel/iwlegacy/3945-rs.c:606: warning: Function parameter or member 'txrc' not described in 'il3945_rs_get_rate'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/3945-mac.c:821: warning: Function parameter or member 'il' not described in 'il3945_setup_handlers'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:915: warning: Function parameter or member 'il' not described in 'il3945_dma_addr2rbd_ptr'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:915: warning: Function parameter or member 'dma_addr' not described in 'il3945_dma_addr2rbd_ptr'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:932: warning: Function parameter or member 'il' not described in 'il3945_rx_queue_restock'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:979: warning: Function parameter or member 'il' not described in 'il3945_rx_allocate'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:979: warning: Function parameter or member 'priority' not described in 'il3945_rx_allocate'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1179: warning: Function parameter or member 'il' not described in 'il3945_rx_handle'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'il' not described in 'il3945_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'image' not described in 'il3945_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1663: warning: Function parameter or member 'len' not described in 'il3945_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'il' not described in 'il3945_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'image' not described in 'il3945_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1703: warning: Function parameter or member 'len' not described in 'il3945_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1739: warning: Function parameter or member 'il' not described in 'il3945_verify_ucode'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:1821: warning: Function parameter or member 'il' not described in 'il3945_read_ucode'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:2061: warning: Function parameter or member 'il' not described in 'il3945_set_ucode_ptrs'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:2093: warning: Function parameter or member 'il' not described in 'il3945_init_alive_start'
drivers/net/wireless/intel/iwlegacy/3945-mac.c:2135: warning: Function parameter or member 'il' not described in 'il3945_alive_start'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-4-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:850:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1027:20: warning: variable ‘scb_ampdu’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-3-lee.jones@linaro.org
Saves on 10's of complains about 'defined but not used' variables.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/marvell/mwifiex/main.h:57,
from drivers/net/wireless/marvell/mwifiex/main.c:22:
drivers/net/wireless/marvell/mwifiex/pcie.h:310:41: warning: ‘mwifiex_pcie8997’ defined but not used [-Wunused-const-variable=]
310 | static const struct mwifiex_pcie_device mwifiex_pcie8997 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:300:41: warning: ‘mwifiex_pcie8897’ defined but not used [-Wunused-const-variable=]
300 | static const struct mwifiex_pcie_device mwifiex_pcie8897 = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/pcie.h:292:41: warning: ‘mwifiex_pcie8766’ defined but not used [-Wunused-const-variable=]
292 | static const struct mwifiex_pcie_device mwifiex_pcie8766 = {
| ^~~~~~~~~~~~~~~~
NB: Repeats 10's of times - snipped for brevity.
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Xinming Hu <huxinming820@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-2-lee.jones@linaro.org
As of the patch ("ath10k: Keep track of which interrupts fired, don't
poll them") we now have no users of this hardware parameter. Remove
it.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200709082024.v2.2.I083faa4e62e69f863311c89ae5eb28ec5a229b70@changeid
If we have a per CE (Copy Engine) IRQ then we have no summary
register. Right now the code generates a summary register by
iterating over all copy engines and seeing if they have an interrupt
pending.
This has a problem. Specifically if _none_ if the Copy Engines have
an interrupt pending then they might go into low power mode and
reading from their address space will cause a full system crash. This
was seen to happen when two interrupts went off at nearly the same
time. Both were handled by a single call of ath10k_snoc_napi_poll()
but, because there were two interrupts handled and thus two calls to
napi_schedule() there was still a second call to
ath10k_snoc_napi_poll() which ran with no interrupts pending.
Instead of iterating over all the copy engines, let's just keep track
of the IRQs that fire. Then we can effectively generate our own
summary without ever needing to read the Copy Engines.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200709082024.v2.1.I4d2f85ffa06f38532631e864a3125691ef5ffe06@changeid
Currently the NAPI processing loops through all
the copy engines and processes a particular copy
engine is the copy completion is set for that copy
engine. The host driver is not supposed to access
any copy engine register after clearing the interrupt
status register.
This might result in kernel crash like the one below
[ 1159.220143] Call trace:
[ 1159.220170] ath10k_snoc_read32+0x20/0x40 [ath10k_snoc]
[ 1159.220193] ath10k_ce_per_engine_service_any+0x78/0x130 [ath10k_core]
[ 1159.220203] ath10k_snoc_napi_poll+0x38/0x8c [ath10k_snoc]
[ 1159.220270] net_rx_action+0x100/0x3b0
[ 1159.220312] __do_softirq+0x164/0x30c
[ 1159.220345] run_ksoftirqd+0x2c/0x64
[ 1159.220380] smpboot_thread_fn+0x1b0/0x288
[ 1159.220405] kthread+0x11c/0x12c
[ 1159.220423] ret_from_fork+0x10/0x18
To avoid such a scenario, we generate an interrupt
summary by reading the copy completion for all the
copy engine before actually processing any of them.
This will avoid reading the interrupt status register
for any CE after the interrupt status is cleared.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593193967-29897-1-git-send-email-pillair@codeaurora.org
In p54p_tx(), skb->data is mapped to streaming DMA on line 337:
mapping = pci_map_single(..., skb->data, ...);
Then skb->data is accessed on line 349:
desc->device_addr = ((struct p54_hdr *)skb->data)->req_id;
This access may cause data inconsistency between CPU cache and hardware.
To fix this problem, ((struct p54_hdr *)skb->data)->req_id is stored in
a local variable before DMA mapping, and then the driver accesses this
local variable instead of skb->data.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802132949.26788-1-baijiaju@tsinghua.edu.cn
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c: In function ‘_rtl92c_phy_iq_calibrate’:
drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c:1223:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: zhengbin <zhengbin13@huawei.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-30-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:504:18: warning: ‘brcmf_fws_prio2fifo’ defined but not used [-Wunused-const-variable=]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-25-lee.jones@linaro.org
No parameters were documented and it's the only one in the file.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/4965-calib.c:608: warning: Function parameter or member 'il' not described in 'il4965_find_disconn_antenna'
drivers/net/wireless/intel/iwlegacy/4965-calib.c:608: warning: Function parameter or member 'average_sig' not described in 'il4965_find_disconn_antenna'
drivers/net/wireless/intel/iwlegacy/4965-calib.c:608: warning: Function parameter or member 'data' not described in 'il4965_find_disconn_antenna'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/4965-rs.c:156: warning: cannot understand function prototype: 's32 expected_tpt_legacy[RATE_COUNT] = '
drivers/net/wireless/intel/iwlegacy/4965-rs.c:406: warning: Function parameter or member 'tbl' not described in 'il4965_rs_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:406: warning: Function parameter or member 'scale_idx' not described in 'il4965_rs_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:406: warning: Function parameter or member 'attempts' not described in 'il4965_rs_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:406: warning: Function parameter or member 'successes' not described in 'il4965_rs_collect_tx_data'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:629: warning: Function parameter or member 'il' not described in 'il4965_rs_use_green'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:629: warning: Function parameter or member 'sta' not described in 'il4965_rs_use_green'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:645: warning: Function parameter or member 'lq_sta' not described in 'il4965_rs_get_supported_rates'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:645: warning: Function parameter or member 'hdr' not described in 'il4965_rs_get_supported_rates'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:645: warning: Function parameter or member 'rate_type' not described in 'il4965_rs_get_supported_rates'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2130: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2134: warning: Function parameter or member 'il' not described in 'il4965_rs_initialize_lq'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2134: warning: Function parameter or member 'conf' not described in 'il4965_rs_initialize_lq'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2134: warning: Function parameter or member 'sta' not described in 'il4965_rs_initialize_lq'
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2134: warning: Function parameter or member 'lq_sta' not described in 'il4965_rs_initialize_lq'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_debugfs.c:21: warning: Incorrect use of kernel-doc format: * rsi_sdio_stats_read() - This function returns the sdio status of the driver.
drivers/net/wireless/rsi/rsi_91x_debugfs.c:28: warning: Function parameter or member 'seq' not described in 'rsi_sdio_stats_read'
drivers/net/wireless/rsi/rsi_91x_debugfs.c:28: warning: Function parameter or member 'data' not described in 'rsi_sdio_stats_read'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_ht.c: In function ‘b43_phy_ht_op_init’:
drivers/net/wireless/broadcom/b43/phy_ht.c:904:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-18-lee.jones@linaro.org
The function headers are either very weakly documented or not at all.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'reg50' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:94: warning: Function parameter or member 'saved_regs_part2' not described in 'brcmf_btcoex_info'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:233: warning: Function parameter or member 'btci' not described in 'btcmf_btcoex_save_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:253: warning: Function parameter or member 'btci' not described in 'brcmf_btcoex_restore_part1'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:273: warning: Function parameter or member 't' not described in 'brcmf_btcoex_timerfunc'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'vif' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Function parameter or member 'duration' not described in 'brcmf_btcoex_set_mode'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/btcoex.c:453: warning: Excess function parameter 'cfg' description in 'brcmf_btcoex_set_mode'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-17-lee.jones@linaro.org
These are clearly not suitable for kernel-doc.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/4965-mac.c:234: warning: Function parameter or member 'il' not described in 'il4965_dma_addr2rbd_ptr'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:234: warning: Function parameter or member 'dma_addr' not described in 'il4965_dma_addr2rbd_ptr'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:251: warning: Function parameter or member 'il' not described in 'il4965_rx_queue_restock'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:301: warning: Function parameter or member 'il' not described in 'il4965_rx_allocate'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:301: warning: Function parameter or member 'priority' not described in 'il4965_rx_allocate'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:1138: warning: Function parameter or member 'il' not described in 'il4965_set_rxon_chain'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:1943: warning: Function parameter or member 'il' not described in 'il4965_hw_txq_ctx_free'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:1971: warning: Function parameter or member 'il' not described in 'il4965_txq_ctx_alloc'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2068: warning: Function parameter or member 'il' not described in 'il4965_txq_ctx_stop'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2109: warning: Function parameter or member 'il' not described in 'il4965_tx_queue_stop_scheduler'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2109: warning: Function parameter or member 'txq_id' not described in 'il4965_tx_queue_stop_scheduler'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2122: warning: Function parameter or member 'il' not described in 'il4965_tx_queue_set_q2ratid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2122: warning: Function parameter or member 'ra_tid' not described in 'il4965_tx_queue_set_q2ratid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2122: warning: Function parameter or member 'txq_id' not described in 'il4965_tx_queue_set_q2ratid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'il' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'txq_id' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'tx_fifo' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'sta_id' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'tid' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2153: warning: Function parameter or member 'ssn_idx' not described in 'il4965_txq_agg_enable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2285: warning: Function parameter or member 'il' not described in 'il4965_txq_agg_disable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2285: warning: Function parameter or member 'txq_id' not described in 'il4965_txq_agg_disable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2285: warning: Function parameter or member 'ssn_idx' not described in 'il4965_txq_agg_disable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2285: warning: Function parameter or member 'tx_fifo' not described in 'il4965_txq_agg_disable'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2500: warning: Function parameter or member 'il' not described in 'il4965_tx_status_reply_compressed_ba'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2500: warning: Function parameter or member 'agg' not described in 'il4965_tx_status_reply_compressed_ba'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2500: warning: Function parameter or member 'ba_resp' not described in 'il4965_tx_status_reply_compressed_ba'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2651: warning: Function parameter or member 'il' not described in 'il4965_tx_status_reply_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2651: warning: Function parameter or member 'agg' not described in 'il4965_tx_status_reply_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2651: warning: Function parameter or member 'tx_resp' not described in 'il4965_tx_status_reply_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2651: warning: Function parameter or member 'txq_id' not described in 'il4965_tx_status_reply_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2651: warning: Function parameter or member 'start_idx' not described in 'il4965_tx_status_reply_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2761: warning: Function parameter or member 'il' not described in 'il4965_hdl_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2761: warning: Function parameter or member 'rxb' not described in 'il4965_hdl_tx'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2882: warning: Function parameter or member 'il' not described in 'il4965_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2882: warning: Function parameter or member 'rate_n_flags' not described in 'il4965_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2882: warning: Function parameter or member 'info' not described in 'il4965_hwrate_to_tx_control'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2908: warning: Function parameter or member 'il' not described in 'il4965_hdl_compressed_ba'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:2908: warning: Function parameter or member 'rxb' not described in 'il4965_hdl_compressed_ba'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3514: warning: Function parameter or member 'il' not described in 'il4965_alloc_bcast_station'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3554: warning: Function parameter or member 'il' not described in 'il4965_update_bcast_station'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3587: warning: Function parameter or member 'il' not described in 'il4965_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3587: warning: Function parameter or member 'sta_id' not described in 'il4965_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3587: warning: Function parameter or member 'tid' not described in 'il4965_sta_tx_modify_enable_tid'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3916: warning: Function parameter or member 'il' not described in 'il4965_hw_txq_free_tfd'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:3916: warning: Function parameter or member 'txq' not described in 'il4965_hw_txq_free_tfd'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4059: warning: Function parameter or member 't' not described in 'il4965_bg_stats_periodic'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4169: warning: Function parameter or member 'il' not described in 'il4965_setup_handlers'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4211: warning: Function parameter or member 'il' not described in 'il4965_rx_handle'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4767: warning: Function parameter or member 'ucode_raw' not described in 'il4965_ucode_callback'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:4767: warning: Function parameter or member 'context' not described in 'il4965_ucode_callback'
drivers/net/wireless/intel/iwlegacy/4965-mac.c:5269: warning: Function parameter or member 'il' not described in 'il4965_alive_start'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_coex.c:24: warning: Function parameter or member 'coex_cb' not described in 'rsi_coex_determine_coex_q'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-15-lee.jones@linaro.org
The function parameter is not documented and either are any of the
other functions in this source file.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:69: warning: Function parameter or member 'c' not described in 'is_nvram_char'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_ps.c:26: warning: Function parameter or member 'state' not described in 'str_psstate'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:27:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:845:6: warning: variable ‘mcl’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_phy_reset’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1779:7: warning: variable ‘phy_in_reset’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_ucode_download’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:2273:23: warning: variable ‘wlc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_b_coreinit’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3176:6: warning: variable ‘sflags’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_set_chanspec’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3902:7: warning: variable ‘switchband’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_down’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5182:7: warning: variable ‘dev_gone’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_ofdm_rateset_war’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5393:5: warning: variable ‘r’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘mac80211_wlc_set_nrate’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5876:6: warning: variable ‘bcmerror’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function ‘brcms_c_d11hdrs_mac80211’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:6213:7: warning: variable ‘short_preamble’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_mgmt.c:713: warning: Function parameter or member 'mac_addr' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:713: warning: Function parameter or member 'vap_id' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:713: warning: Function parameter or member 'vap_status' not described in 'rsi_set_vap_capabilities'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-7-lee.jones@linaro.org
Some formatting issues, some missing and some extra descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:162: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'oui' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:181: warning: Function parameter or member 'elts' not described in 'brcmf_p2p_action_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:196: warning: Function parameter or member 'query_data' not described in 'brcmf_p2psd_gas_pub_act_frame'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:210: warning: Function parameter or member 'extra_listen' not described in 'brcmf_config_af_params'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Function parameter or member 'ifp' not described in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'ndev' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:776: warning: Excess function parameter 'action' description in 'brcmf_p2p_run_escan'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'wdev' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:977: warning: Function parameter or member 'cookie' not described in 'brcmf_p2p_remain_on_channel'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1063: warning: Function parameter or member 'channel' not described in 'brcmf_p2p_act_frm_search'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1337: warning: Function parameter or member 'mac' not described in 'brcmf_p2p_gon_req_collision'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'cfg' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Function parameter or member 'if_type' not described in 'brcmf_p2p_ifchange'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2046: warning: Excess function parameter 'mac' description in 'brcmf_p2p_ifchange'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-6-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
from drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:18:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_finalize’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:648:25: warning: variable ‘sgi’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus_complete’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:856:18: warning: variable ‘rr_retry_limit’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:855:5: warning: variable ‘antselid’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:41: warning: variable ‘tx_error’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:853:7: warning: variable ‘update_rate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c: In function ‘brcms_c_ampdu_dotxstatus’:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1037:28: warning: variable ‘tx_info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/ampdu.c:1035:28: warning: variable ‘ini’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_mac80211.c:1021: warning: Function parameter or member 'sta' not described in 'rsi_mac80211_set_key'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821071644.109970-3-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intersil/hostap/hostap_ioctl.c: In function ‘prism2_translate_scan’:
drivers/net/wireless/intersil/hostap/hostap_ioctl.c:1958:13: warning: variable ‘hostscan’ set but not used [-Wunused-but-set-variable]
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-29-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/if_usb.c:56: warning: Function parameter or member 'urb' not described in 'if_usb_write_bulk_callback'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:73: warning: Function parameter or member 'cardp' not described in 'if_usb_free'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'intf' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:146: warning: Function parameter or member 'id' not described in 'if_usb_probe'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:244: warning: Function parameter or member 'intf' not described in 'if_usb_disconnect'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:272: warning: Function parameter or member 'cardp' not described in 'if_usb_send_fw_pkt'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'cardp' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'payload' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'nb' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:372: warning: Function parameter or member 'data' not described in 'usb_tx_block'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:625: warning: Function parameter or member 'urb' not described in 'if_usb_receive'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'priv' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'type' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'payload' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:714: warning: Function parameter or member 'nb' not described in 'if_usb_host_to_card'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'cardp' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:742: warning: Function parameter or member 'ivalue' not described in 'if_usb_issue_boot_command'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'data' not described in 'check_fwfile_format'
drivers/net/wireless/marvell/libertas_tf/if_usb.c:766: warning: Function parameter or member 'totlen' not described in 'check_fwfile_format'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-28-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Function parameter or member 'device' not described in 'lbs_get_firmware_async'
drivers/net/wireless/marvell/libertas/firmware.c:134: warning: Excess function parameter 'dev' description in 'lbs_get_firmware_async'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-27-lee.jones@linaro.org
'vif' is a function parameter which is oddly overwritten within the
function, but never read back. 'timeout' is set, but never checked.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c: In function ‘brcmf_p2p_scan_prep’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:894:31: warning: parameter ‘vif’ set but not used [-Wunused-but-set-parameter]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c: In function ‘brcmf_p2p_tx_action_frame’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1549:6: warning: variable ‘timeout’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/4965.c:35: warning: Function parameter or member 'il' not described in 'il4965_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/4965.c:35: warning: Function parameter or member 'image' not described in 'il4965_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/4965.c:35: warning: Function parameter or member 'len' not described in 'il4965_verify_inst_sparse'
drivers/net/wireless/intel/iwlegacy/4965.c:66: warning: Function parameter or member 'il' not described in 'il4965_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/4965.c:66: warning: Function parameter or member 'image' not described in 'il4965_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/4965.c:66: warning: Function parameter or member 'len' not described in 'il4965_verify_inst_full'
drivers/net/wireless/intel/iwlegacy/4965.c:105: warning: Function parameter or member 'il' not described in 'il4965_verify_ucode'
drivers/net/wireless/intel/iwlegacy/4965.c:329: warning: Function parameter or member 'il' not described in 'il4965_load_bsm'
drivers/net/wireless/intel/iwlegacy/4965.c:416: warning: Function parameter or member 'il' not described in 'il4965_set_ucode_ptrs'
drivers/net/wireless/intel/iwlegacy/4965.c:451: warning: Function parameter or member 'il' not described in 'il4965_init_alive_start'
drivers/net/wireless/intel/iwlegacy/4965.c:583: warning: Function parameter or member 'eeprom_voltage' not described in 'il4965_get_voltage_compensation'
drivers/net/wireless/intel/iwlegacy/4965.c:583: warning: Function parameter or member 'current_voltage' not described in 'il4965_get_voltage_compensation'
drivers/net/wireless/intel/iwlegacy/4965.c:668: warning: Function parameter or member 'il' not described in 'il4965_interpolate_chan'
drivers/net/wireless/intel/iwlegacy/4965.c:668: warning: Function parameter or member 'channel' not described in 'il4965_interpolate_chan'
drivers/net/wireless/intel/iwlegacy/4965.c:668: warning: Function parameter or member 'chan_info' not described in 'il4965_interpolate_chan'
drivers/net/wireless/intel/iwlegacy/4965.c:1242: warning: Function parameter or member 'il' not described in 'il4965_send_tx_power'
drivers/net/wireless/intel/iwlegacy/4965.c:1537: warning: Function parameter or member 'il' not described in 'il4965_txq_update_byte_cnt_tbl'
drivers/net/wireless/intel/iwlegacy/4965.c:1537: warning: Function parameter or member 'txq' not described in 'il4965_txq_update_byte_cnt_tbl'
drivers/net/wireless/intel/iwlegacy/4965.c:1537: warning: Function parameter or member 'byte_cnt' not described in 'il4965_txq_update_byte_cnt_tbl'
drivers/net/wireless/intel/iwlegacy/4965.c:1564: warning: Function parameter or member 'il' not described in 'il4965_hw_get_temperature'
drivers/net/wireless/intel/iwlegacy/4965.c:1564: warning: Excess function parameter 'stats' description in 'il4965_hw_get_temperature'
drivers/net/wireless/intel/iwlegacy/4965.c:1633: warning: Function parameter or member 'il' not described in 'il4965_is_temp_calib_needed'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-25-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_hal.c:25: warning: cannot understand function prototype: 'struct ta_metadata metadata_flash_content[] = '
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-24-lee.jones@linaro.org
Too many, not enough, misnamed and formatting problems, all resolved.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_mgmt.c:24: warning: cannot understand function prototype: 'struct bootup_params boot_params_20 = '
drivers/net/wireless/rsi/rsi_91x_mgmt.c:487: warning: Excess function parameter 'type' description in 'rsi_mgmt_pkt_to_core'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:538: warning: Function parameter or member 'sta_id' not described in 'rsi_hal_send_sta_notify_frame'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:538: warning: Function parameter or member 'vif' not described in 'rsi_hal_send_sta_notify_frame'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:615: warning: Function parameter or member 'sta_id' not described in 'rsi_send_aggregation_params_frame'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:711: warning: Function parameter or member 'mode' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:711: warning: Function parameter or member 'mac_addr' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:711: warning: Function parameter or member 'vap_id' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:711: warning: Function parameter or member 'vap_status' not described in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:711: warning: Excess function parameter 'opmode' description in 'rsi_set_vap_capabilities'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:794: warning: Function parameter or member 'sta_id' not described in 'rsi_hal_load_key'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:794: warning: Function parameter or member 'vif' not described in 'rsi_hal_load_key'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1053: warning: Function parameter or member 'curchan' not described in 'rsi_band_check'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1173: warning: Excess function parameter 'channel' description in 'rsi_send_radio_params_update'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1299: warning: Function parameter or member 'sta' not described in 'rsi_send_auto_rate_request'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1299: warning: Function parameter or member 'sta_id' not described in 'rsi_send_auto_rate_request'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1299: warning: Function parameter or member 'vif' not described in 'rsi_send_auto_rate_request'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'opmode' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'addr' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'sta' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'sta_id' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'assoc_cap' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Function parameter or member 'vif' not described in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1459: warning: Excess function parameter 'bssid' description in 'rsi_inform_bss_status'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1543: warning: Function parameter or member 'common' not described in 'rsi_send_block_unblock_frame'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1543: warning: Function parameter or member 'block_event' not described in 'rsi_send_block_unblock_frame'
drivers/net/wireless/rsi/rsi_91x_mgmt.c:1587: warning: Excess function parameter 'Return' description in 'rsi_send_rx_filter_frame'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-21-lee.jones@linaro.org
- File headers should not be kernel-doc
- Misnaming issues
- Missing function parameter documentation
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_mac80211.c:24: warning: cannot understand function prototype: 'const struct ieee80211_channel rsi_2ghz_channels[] = '
drivers/net/wireless/rsi/rsi_91x_mac80211.c:739: warning: Function parameter or member 'vif' not described in 'rsi_get_connected_channel'
drivers/net/wireless/rsi/rsi_91x_mac80211.c:739: warning: Excess function parameter 'adapter' description in 'rsi_get_connected_channel'
drivers/net/wireless/rsi/rsi_91x_mac80211.c:868: warning: Function parameter or member 'changed_flags' not described in 'rsi_mac80211_conf_filter'
drivers/net/wireless/rsi/rsi_91x_mac80211.c:868: warning: Excess function parameter 'changed' description in 'rsi_mac80211_conf_filter'
drivers/net/wireless/rsi/rsi_91x_mac80211.c:946: warning: Function parameter or member 'sta' not described in 'rsi_hal_key_config'
drivers/net/wireless/rsi/rsi_91x_mac80211.c:1245: warning: Function parameter or member 'vif' not described in 'rsi_perform_cqm'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-19-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_main.c:157: warning: Function parameter or member 'rx_pkt' not described in 'rsi_read_pkt'
drivers/net/wireless/rsi/rsi_91x_main.c:157: warning: Excess function parameter 'rcv_pkt' description in 'rsi_read_pkt'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/mediatek/mt7601u/phy.c:1216: warning: Function parameter or member 'dac' not described in 'mt7601u_set_tx_dac'
drivers/net/wireless/mediatek/mt7601u/phy.c:1216: warning: Excess function parameter 'path' description in 'mt7601u_set_tx_dac'
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas/main.c:727: warning: Function parameter or member 't' not described in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:727: warning: Excess function parameter 'data' description in 'lbs_cmd_timeout_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Function parameter or member 't' not described in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:761: warning: Excess function parameter 'data' description in 'lbs_tx_lockup_handler'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Function parameter or member 't' not described in 'auto_deepsleep_timer_fn'
drivers/net/wireless/marvell/libertas/main.c:784: warning: Excess function parameter 'data' description in 'auto_deepsleep_timer_fn'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-15-lee.jones@linaro.org
They're never read, so there is no reason for them to exist.
They just cause the compiler to complain.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/st/cw1200/wsm.c: In function ‘wsm_ba_timeout_indication’:
drivers/net/wireless/st/cw1200/wsm.c:1033:5: warning: variable ‘dummy2’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/st/cw1200/wsm.c:1031:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-14-lee.jones@linaro.org
Keeping this around to act as documentation, since its use is
currently #if'ed out at the end of the function.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intersil/hostap/hostap_ap.c: In function ‘handle_assoc’:
drivers/net/wireless/intersil/hostap/hostap_ap.c:1507:8: warning: variable ‘txt’ set but not used [-Wunused-but-set-variable]
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-12-lee.jones@linaro.org
This is the only use of kerneldoc in the sourcefile and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/debug.c:1373: warning: Function parameter or member 'il' not described in 'il_dbgfs_unregister'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-10-lee.jones@linaro.org
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Also demote one stray non-kernel-doc header.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'priv' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'extra' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:44: warning: Function parameter or member 'resp' not described in 'lbtf_cmd_copyback'
drivers/net/wireless/marvell/libertas_tf/cmd.c:80: warning: Function parameter or member 'priv' not described in 'lbtf_update_hw_spec'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'priv' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:150: warning: Function parameter or member 'channel' not described in 'lbtf_set_channel'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'priv' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:277: warning: Function parameter or member 'cmdnode' not described in '__lbtf_cleanup_and_insert_cmd'
drivers/net/wireless/marvell/libertas_tf/cmd.c:442: warning: Function parameter or member 'priv' not described in 'lbtf_allocate_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:490: warning: Function parameter or member 'priv' not described in 'lbtf_free_cmd_buffer'
drivers/net/wireless/marvell/libertas_tf/cmd.c:527: warning: Function parameter or member 'priv' not described in 'lbtf_get_cmd_ctrl_node'
drivers/net/wireless/marvell/libertas_tf/cmd.c:561: warning: Function parameter or member 'priv' not described in 'lbtf_execute_next_command'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-8-lee.jones@linaro.org
Firstly a rename, then a split (there are 2 'len's that need documenting).
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ti/wlcore/cmd.c:832: warning: Function parameter or member 'buf_len' not described in 'wl1271_cmd_test'
drivers/net/wireless/ti/wlcore/cmd.c:832: warning: Excess function parameter 'len' description in 'wl1271_cmd_test'
drivers/net/wireless/ti/wlcore/cmd.c:862: warning: Function parameter or member 'cmd_len' not described in 'wl1271_cmd_interrogate'
drivers/net/wireless/ti/wlcore/cmd.c:862: warning: Function parameter or member 'res_len' not described in 'wl1271_cmd_interrogate'
drivers/net/wireless/ti/wlcore/cmd.c:862: warning: Excess function parameter 'len' description in 'wl1271_cmd_interrogate'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Hari Nagalla <hnagalla@gmail.com>
Cc: Guy Mishol <guym@ti.com>
Cc: Maital Hahn <maitalm@ti.com>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-7-lee.jones@linaro.org
There are only 2 kernel-doc headers in this file and both are
incorrect. The first one does not attempt to document the function at
all and the second one is suffering from severe doc-rot; the format is
wrong and only 1 out of 3 parameters are being documented.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/marvell/libertas_tf/main.c:129: warning: Function parameter or member 't' not described in 'command_timer_fn'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'card' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'dmdev' not described in 'lbtf_add_card'
drivers/net/wireless/marvell/libertas_tf/main.c:554: warning: Function parameter or member 'ops' not described in 'lbtf_add_card'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_core.c:23: warning: Incorrect use of kernel-doc format: * rsi_determine_min_weight_queue() - This function determines the queue with
drivers/net/wireless/rsi/rsi_91x_core.c:30: warning: Function parameter or member 'common' not described in 'rsi_determine_min_weight_queue'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-4-lee.jones@linaro.org
The file header should not be kernel-doc. Add missing 'rec_pkt'
description. Update 'rsi_91x_init()'s parameter description.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/rsi/rsi_91x_main.c:17: warning: Function parameter or member 'fmt' not described in 'pr_fmt'
drivers/net/wireless/rsi/rsi_91x_main.c:156: warning: Function parameter or member 'rx_pkt' not described in 'rsi_read_pkt'
drivers/net/wireless/rsi/rsi_91x_main.c:287: warning: Function parameter or member 'oper_mode' not described in 'rsi_91x_init'
drivers/net/wireless/rsi/rsi_91x_main.c:287: warning: Excess function parameter 'void' description in 'rsi_91x_init'
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-3-lee.jones@linaro.org
'freq_list' is used in some source files which include hostap.h, but
not all. The compiler complains about the times it's not used. Mark
it as __maybe_used to tell the compiler that this is not only okay,
it's expected.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/intersil/hostap/hostap_80211_tx.c:9:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
In file included from drivers/net/wireless/intersil/hostap/hostap_main.c:31:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
In file included from drivers/net/wireless/intersil/hostap/hostap_proc.c:10:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
In file included from drivers/net/wireless/intersil/hostap/hostap_hw.c:50,
from drivers/net/wireless/intersil/hostap/hostap_cs.c:196:
At top level:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
In file included from drivers/net/wireless/intersil/hostap/hostap_hw.c:50,
from drivers/net/wireless/intersil/hostap/hostap_pci.c:221:
At top level:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
In file included from drivers/net/wireless/intersil/hostap/hostap_hw.c:50,
from drivers/net/wireless/intersil/hostap/hostap_plx.c:264:
At top level:
drivers/net/wireless/intersil/hostap/hostap.h:11:19: warning: ‘freq_list’ defined but not used [-Wunused-const-variable=]
Cc: Jouni Malinen <j@w1.fi>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-2-lee.jones@linaro.org
Tasklet conversion patch introduced a build
warning in _rtl_usb_init_rx, this patch fixes the warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: d3ccc14dfe ("rtlwifi/rtw88: convert tasklets to use new tasklet_setup() API")
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831043659.281712-1-allen.lkml@gmail.com
Tasklet conversion patches intoruced a build warning
in init_usb_rx(), this patch fixes the same.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 26721b0246 ("zd1211rw: convert tasklets to use new tasklet_setup() API")
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200831043425.281538-1-allen.lkml@gmail.com
Change the misleading macro name to one that is more descriptive for
rtl8723-common. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-14-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8723be. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-13-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8723ae. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-12-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192se. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-11-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192ee. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-10-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192de. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-9-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192cu. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-8-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192ce. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-7-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8192-common. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-6-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
rtl8188ee. Changes suggested by ckeckpatch.pl have been made.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-5-Larry.Finger@lwfinger.net
Change the misleading macro name to one that is more descriptive for
btcoexist.
This change exposed some conditions reported by checkpatch.pl.
These are also fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-4-Larry.Finger@lwfinger.net
The macro name RT_TRACE makes it seem that it is used for tracing, when
is actually used for debugging. Change the name to rtl_dbg. Any Sparse
errors exposed by this change were also fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-3-Larry.Finger@lwfinger.net
The macro name RT_TRACE makes it seem that it is used for tracing, when
is actually used for debugging. Change the name to RT_DEBUG.
This step creates the new macro while keeping the old RT_TRACE to allow
building. It will be removed at the end of the patch series.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-2-Larry.Finger@lwfinger.net
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
variable _len_.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616225132.GA19873@embeddedor
'ar9170_qmap' is used in some source files which include carl9170.h,
but not all of them. A 'defined but not used' warning is thrown when
compiling the ones which do not use it.
Fixes the following W=1 kernel build warning(s)
from drivers/net/wireless/ath/carl9170/carl9170.h:57,
In file included from drivers/net/wireless/ath/carl9170/carl9170.h:57,
drivers/net/wireless/ath/carl9170/carl9170.h:71:17: warning: ‘ar9170_qmap’ defined but not used [-Wunused-const-variable=]
NB: Snipped - lots of these repeat
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827093351.GA1627017@dell
There has been no attempt to document any of the function parameters here.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'dev' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'ops' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'rops' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'wil_handle' not described in 'wil_platform_init'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073832.GW3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'wil' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'num_descriptors' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'descriptor_size' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:229: warning: Function parameter or member 'wil' not described in 'wil_pmc_free'
drivers/net/wireless/ath/wil6210/pmc.c:229: warning: Function parameter or member 'send_pmc_cmd' not described in 'wil_pmc_free'
drivers/net/wireless/ath/wil6210/pmc.c:307: warning: Function parameter or member 'wil' not described in 'wil_pmc_last_cmd_status'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'filp' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'buf' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'count' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'f_pos' not described in 'wil_pmc_read'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073718.GV3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'wil' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'ring' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'i' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'wil' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'sring' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tso_desc_type' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'is_ipv4' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tcp_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'skb_net_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'mss' not described in 'wil_tx_desc_offload_setup_tso_edma'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073545.GU3248864@dell
None of these headers provide any parameter documentation.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'wil' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'vring' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'i' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'headroom' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:309: warning: Function parameter or member 'wil' not described in 'wil_rx_add_radiotap_header'
drivers/net/wireless/ath/wil6210/txrx.c:309: warning: Function parameter or member 'skb' not described in 'wil_rx_add_radiotap_header'
drivers/net/wireless/ath/wil6210/txrx.c:444: warning: Function parameter or member 'wil' not described in 'wil_vring_reap_rx'
drivers/net/wireless/ath/wil6210/txrx.c:444: warning: Function parameter or member 'vring' not described in 'wil_vring_reap_rx'
drivers/net/wireless/ath/wil6210/txrx.c:610: warning: Function parameter or member 'wil' not described in 'wil_rx_refill'
drivers/net/wireless/ath/wil6210/txrx.c:610: warning: Function parameter or member 'count' not described in 'wil_rx_refill'
drivers/net/wireless/ath/wil6210/txrx.c:1011: warning: Function parameter or member 'wil' not described in 'wil_rx_handle'
drivers/net/wireless/ath/wil6210/txrx.c:1011: warning: Function parameter or member 'quota' not described in 'wil_rx_handle'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'skb' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'tso_desc_type' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'is_ipv4' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'tcp_hdr_len' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'skb_net_hdr_len' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1674: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup'
drivers/net/wireless/ath/wil6210/txrx.c:1674: warning: Function parameter or member 'skb' not described in 'wil_tx_desc_offload_setup'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'wil' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'vif' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'ring' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'check_stop' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2430: warning: Function parameter or member 'vif' not described in 'wil_tx_complete'
drivers/net/wireless/ath/wil6210/txrx.c:2430: warning: Function parameter or member 'ringid' not described in 'wil_tx_complete'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073442.GT3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/interrupt.c:652: warning: Function parameter or member 'irq' not described in 'wil6210_thread_irq'
drivers/net/wireless/ath/wil6210/interrupt.c:652: warning: Function parameter or member 'cookie' not described in 'wil6210_thread_irq'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073338.GS3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wmi.c:52: warning: Incorrect use of kernel-doc format: * Addressing - theory of operations
drivers/net/wireless/ath/wil6210/wmi.c:70: warning: Incorrect use of kernel-doc format: * @sparrow_fw_mapping provides memory remapping table for sparrow
drivers/net/wireless/ath/wil6210/wmi.c:80: warning: cannot understand function prototype: 'const struct fw_map sparrow_fw_mapping[] = '
drivers/net/wireless/ath/wil6210/wmi.c:107: warning: Cannot understand * @sparrow_d0_mac_rgf_ext - mac_rgf_ext section for Sparrow D0
drivers/net/wireless/ath/wil6210/wmi.c:115: warning: Cannot understand * @talyn_fw_mapping provides memory remapping table for Talyn
drivers/net/wireless/ath/wil6210/wmi.c:158: warning: Cannot understand * @talyn_mb_fw_mapping provides memory remapping table for Talyn-MB
drivers/net/wireless/ath/wil6210/wmi.c:236: warning: Function parameter or member 'x' not described in 'wmi_addr_remap'
drivers/net/wireless/ath/wil6210/wmi.c:255: warning: Function parameter or member 'section' not described in 'wil_find_fw_mapping'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'wil' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'size' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:307: warning: Function parameter or member 'wil' not described in 'wmi_addr'
drivers/net/wireless/ath/wil6210/wmi.c:307: warning: Function parameter or member 'ptr' not described in 'wmi_addr'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'wil' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'vif' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'cid' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'ringid' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'vif' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'id' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'd' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'len' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:2588: warning: Function parameter or member 'wil' not described in 'wmi_rxon'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073201.GR3248864@dell
The return error check on the call to ath11k_pci_get_user_msi_assignment is
missing. If an error does occur, num_vectors is still set to zero and
later on a division by zero can occur when variable vector is being
calculated. Fix this by adding an error check after the call.
Addresses-Coverity: ("Division or modulo by zero")
Fixes: d4ecb90b38 ("ath11k: enable DP interrupt setup for QCA6390")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819111452.52419-1-colin.king@canonical.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-5-allen.cryptic@gmail.com
When devm_clk_get() returns -EPROBE_DEFER, spi_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 854d66df74 ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200819115426.29852-1-dinghao.liu@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly
and remove .data fieldd
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-17-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly
and remove .data field.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-16-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-15-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-14-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-12-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly
and remove .data field.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-11-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-10-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-9-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-8-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-7-allen.cryptic@gmail.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly
and remove .data field.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-6-allen.cryptic@gmail.com
Following commit e186967865 ("mwifiex: Prevent memory corruption
handling keys") the mwifiex driver fails to authenticate with certain
networks, specifically networks with 256 bit keys, and repeatedly asks
for the password. The kernel log repeats the following lines (id and
bssid redacted):
mwifiex_pcie 0000:01:00.0: info: trying to associate to '<id>' bssid <bssid>
mwifiex_pcie 0000:01:00.0: info: associated to bssid <bssid> successfully
mwifiex_pcie 0000:01:00.0: crypto keys added
mwifiex_pcie 0000:01:00.0: info: successfully disconnected from <bssid>: reason code 3
Tracking down this problem lead to the overflow check introduced by the
aforementioned commit into mwifiex_ret_802_11_key_material_v2(). This
check fails on networks with 256 bit keys due to the current storage
size for AES keys in struct mwifiex_aes_param being only 128 bit.
To fix this issue, increase the storage size for AES keys to 256 bit.
Fixes: e186967865 ("mwifiex: Prevent memory corruption handling keys")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reported-by: Kaloyan Nikolov <konik98@gmail.com>
Tested-by: Kaloyan Nikolov <konik98@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200825153829.38043-1-luzmaximilian@gmail.com
Using dev_kfree_skb for tx skbs breaks AQL. This worked until now only
by accident, because a mac80211 issue breaks AQL on drivers with firmware
rate control that report the rate via ieee80211_tx_status_ext as struct
rate_info.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200812144943.91974-1-nbd@nbd.name
The implementation of embedding WTBL update inside the STA_REC update is buggy
on the MT7615 v2 firmware. This leads to connection issues after a station has
connected and disconnected again.
Switch to the v1 MCU API ops, since they have received much more testing and
should be more stable.
On MT7622 and later, the v2 API is more actively used, so we should keep using
it as well.
Fixes: 6849e29ed9 ("mt76: mt7615: add starec operating flow for firmware v2")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200812102332.11812-1-nbd@nbd.name
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_workarounds_rev3plus’:
drivers/net/wireless/broadcom/b43/phy_n.c:3346:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_nphy_spur_workaround’:
drivers/net/wireless/broadcom/b43/phy_n.c:4608:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:4641:4: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c: In function ‘b43_phy_initn’:
drivers/net/wireless/broadcom/b43/phy_n.c:6170:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/phy_n.c:6215:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Michael Buesch <m@bues.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-31-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/phy_common.c:467: warning: Function parameter or member 'work' not described in 'b43_phy_txpower_adjust_work'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Alexander A. Klimov" <grandmaster@al2klimov.de>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-27-lee.jones@linaro.org
Lots of these are either completely wrong or do not even attempt to
document any of the parameters. Others use an incorrect/dated format
which is not recognised by the kernel (... and are also wrong and
suffering from docrot).
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3011: warning: Function parameter or member 'priv' not described in 'ipw_alive'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3693: warning: Incorrect use of kernel-doc format: * Driver allocates buffers of this size for Rx
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3697: warning: Incorrect use of kernel-doc format: * ipw_rx_queue_space - Return number of free slots available in queue.
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3700: warning: Function parameter or member 'q' not described in 'ipw_rx_queue_space'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'priv' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'q' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'count' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'read' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'write' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'base' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3743: warning: Function parameter or member 'size' not described in 'ipw_queue_init'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3800: warning: Function parameter or member 'priv' not described in 'ipw_queue_tx_free_tfd'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3800: warning: Function parameter or member 'txq' not described in 'ipw_queue_tx_free_tfd'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3841: warning: Function parameter or member 'priv' not described in 'ipw_queue_tx_free'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3841: warning: Function parameter or member 'txq' not described in 'ipw_queue_tx_free'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:3869: warning: Function parameter or member 'priv' not described in 'ipw_tx_queue_free'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4474: warning: Function parameter or member 'priv' not described in 'ipw_rx_notification'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4474: warning: Function parameter or member 'notif' not described in 'ipw_rx_notification'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4935: warning: Function parameter or member 'priv' not described in 'ipw_queue_reset'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5008: warning: Function parameter or member 'priv' not described in 'ipw_queue_tx_reclaim'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5008: warning: Function parameter or member 'txq' not described in 'ipw_queue_tx_reclaim'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5008: warning: Function parameter or member 'qindex' not described in 'ipw_queue_tx_reclaim'
drivers/net/wireless/intel/ipw2x00/ipw2200.c:8456: warning: Function parameter or member 'priv' not described in 'ipw_sw_reset'
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Gerald Combs <gerald@ethereal.com>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
In file included from drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:30:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:288: warning: Function parameter or member 'wl' not described in 'brcms_free'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1127: warning: Function parameter or member 'pdev' not described in 'brcms_attach'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1222: warning: Function parameter or member 'pdev' not described in 'brcms_bcma_probe'
drivers/net/wireless/broadcom/brcm80211/brcmsmac/mac80211_if.c:1301: warning: Function parameter or member 'work' not described in 'brcms_driver_init'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-25-lee.jones@linaro.org
Also demote a commit block header which is clearly not suitable for kerneldoc.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c: In function ‘brcmf_fweh_handle_if_event’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:131:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:36: warning: Function parameter or member 'datalen' not described in 'brcmf_fweh_queue_item'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'code' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:44: warning: Function parameter or member 'name' not described in 'brcmf_fweh_event_name'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'emsg' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Function parameter or member 'data' not described in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'item' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:127: warning: Excess function parameter 'ifpp' description in 'brcmf_fweh_handle_if_event'
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:391: warning: Function parameter or member 'packet_len' not described in 'brcmf_fweh_process_event'
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c: In function ‘brcmf_fweh_handle_if_event’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.c:131:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43legacy/main.c: In function ‘b43legacy_interrupt_tasklet’:
drivers/net/wireless/broadcom/b43legacy/main.c:1344:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/ipw2x00/ipw2200.c: In function ‘ipw_irq_tasklet’:
drivers/net/wireless/intel/ipw2x00/ipw2200.c:1953:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/intel/ipw2x00/ipw2200.c: In function ‘ipw_rx’:
drivers/net/wireless/intel/ipw2x00/ipw2200.c:8251:9: warning: variable ‘w’ set but not used [-Wunused-but-set-variable]
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Gerald Combs <gerald@ethereal.com>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-17-lee.jones@linaro.org
Almost all of the headers in this file fail to reach the standards
required by kernel-doc and no "kernel-doc::" references are made to it
from the kernel's Documentation.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/common.c: In function ‘il_enqueue_hcmd’:
drivers/net/wireless/intel/iwlegacy/common.c:3126:6: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/intel/iwlegacy/common.c:697: warning: Function parameter or member 'il' not described in 'il_eeprom_init'
drivers/net/wireless/intel/iwlegacy/common.c:848: warning: Function parameter or member 'il' not described in 'il_mod_ht40_chan_info'
drivers/net/wireless/intel/iwlegacy/common.c:848: warning: Function parameter or member 'band' not described in 'il_mod_ht40_chan_info'
drivers/net/wireless/intel/iwlegacy/common.c:848: warning: Function parameter or member 'channel' not described in 'il_mod_ht40_chan_info'
drivers/net/wireless/intel/iwlegacy/common.c:848: warning: Function parameter or member 'eeprom_ch' not described in 'il_mod_ht40_chan_info'
drivers/net/wireless/intel/iwlegacy/common.c:848: warning: Function parameter or member 'clear_ht40_extension_channel' not described in 'il_mod_ht40_chan_info'
drivers/net/wireless/intel/iwlegacy/common.c:885: warning: Function parameter or member 'il' not described in 'il_init_channel_map'
drivers/net/wireless/intel/iwlegacy/common.c:1035: warning: Function parameter or member 'il' not described in 'il_get_channel_info'
drivers/net/wireless/intel/iwlegacy/common.c:1035: warning: Function parameter or member 'band' not described in 'il_get_channel_info'
drivers/net/wireless/intel/iwlegacy/common.c:1035: warning: Function parameter or member 'channel' not described in 'il_get_channel_info'
drivers/net/wireless/intel/iwlegacy/common.c:1351: warning: Function parameter or member 'il' not described in 'il_scan_cancel'
drivers/net/wireless/intel/iwlegacy/common.c:1365: warning: Function parameter or member 'il' not described in 'il_scan_cancel_timeout'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'il' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'frame' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'ta' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'ies' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'ie_len' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1617: warning: Function parameter or member 'left' not described in 'il_fill_probe_req'
drivers/net/wireless/intel/iwlegacy/common.c:1924: warning: Function parameter or member 'il' not described in 'il_prep_station'
drivers/net/wireless/intel/iwlegacy/common.c:1924: warning: Function parameter or member 'addr' not described in 'il_prep_station'
drivers/net/wireless/intel/iwlegacy/common.c:1924: warning: Function parameter or member 'is_ap' not described in 'il_prep_station'
drivers/net/wireless/intel/iwlegacy/common.c:1924: warning: Function parameter or member 'sta' not described in 'il_prep_station'
drivers/net/wireless/intel/iwlegacy/common.c:2009: warning: Function parameter or member 'il' not described in 'il_add_station_common'
drivers/net/wireless/intel/iwlegacy/common.c:2009: warning: Function parameter or member 'addr' not described in 'il_add_station_common'
drivers/net/wireless/intel/iwlegacy/common.c:2009: warning: Function parameter or member 'is_ap' not described in 'il_add_station_common'
drivers/net/wireless/intel/iwlegacy/common.c:2009: warning: Function parameter or member 'sta' not described in 'il_add_station_common'
drivers/net/wireless/intel/iwlegacy/common.c:2009: warning: Function parameter or member 'sta_id_r' not described in 'il_add_station_common'
drivers/net/wireless/intel/iwlegacy/common.c:2070: warning: Function parameter or member 'il' not described in 'il_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlegacy/common.c:2070: warning: Function parameter or member 'sta_id' not described in 'il_sta_ucode_deactivate'
drivers/net/wireless/intel/iwlegacy/common.c:2144: warning: Function parameter or member 'il' not described in 'il_remove_station'
drivers/net/wireless/intel/iwlegacy/common.c:2144: warning: Function parameter or member 'sta_id' not described in 'il_remove_station'
drivers/net/wireless/intel/iwlegacy/common.c:2144: warning: Function parameter or member 'addr' not described in 'il_remove_station'
drivers/net/wireless/intel/iwlegacy/common.c:2205: warning: Function parameter or member 'il' not described in 'il_clear_ucode_stations'
drivers/net/wireless/intel/iwlegacy/common.c:2237: warning: Function parameter or member 'il' not described in 'il_restore_stations'
drivers/net/wireless/intel/iwlegacy/common.c:2372: warning: Function parameter or member 'il' not described in 'il_is_lq_table_valid'
drivers/net/wireless/intel/iwlegacy/common.c:2372: warning: Function parameter or member 'lq' not described in 'il_is_lq_table_valid'
drivers/net/wireless/intel/iwlegacy/common.c:2401: warning: Function parameter or member 'il' not described in 'il_send_lq_cmd'
drivers/net/wireless/intel/iwlegacy/common.c:2401: warning: Function parameter or member 'lq' not described in 'il_send_lq_cmd'
drivers/net/wireless/intel/iwlegacy/common.c:2401: warning: Function parameter or member 'flags' not described in 'il_send_lq_cmd'
drivers/net/wireless/intel/iwlegacy/common.c:2539: warning: Function parameter or member 'q' not described in 'il_rx_queue_space'
drivers/net/wireless/intel/iwlegacy/common.c:2556: warning: Function parameter or member 'il' not described in 'il_rx_queue_update_write_ptr'
drivers/net/wireless/intel/iwlegacy/common.c:2556: warning: Function parameter or member 'q' not described in 'il_rx_queue_update_write_ptr'
drivers/net/wireless/intel/iwlegacy/common.c:2711: warning: Function parameter or member 'il' not described in 'il_txq_update_write_ptr'
drivers/net/wireless/intel/iwlegacy/common.c:2711: warning: Function parameter or member 'txq' not described in 'il_txq_update_write_ptr'
drivers/net/wireless/intel/iwlegacy/common.c:2751: warning: Function parameter or member 'il' not described in 'il_tx_queue_unmap'
drivers/net/wireless/intel/iwlegacy/common.c:2751: warning: Function parameter or member 'txq_id' not described in 'il_tx_queue_unmap'
drivers/net/wireless/intel/iwlegacy/common.c:2775: warning: Function parameter or member 'il' not described in 'il_tx_queue_free'
drivers/net/wireless/intel/iwlegacy/common.c:2775: warning: Function parameter or member 'txq_id' not described in 'il_tx_queue_free'
drivers/net/wireless/intel/iwlegacy/common.c:2775: warning: Excess function parameter 'txq' description in 'il_tx_queue_free'
drivers/net/wireless/intel/iwlegacy/common.c:2813: warning: Function parameter or member 'il' not described in 'il_cmd_queue_unmap'
drivers/net/wireless/intel/iwlegacy/common.c:2856: warning: Function parameter or member 'il' not described in 'il_cmd_queue_free'
drivers/net/wireless/intel/iwlegacy/common.c:2856: warning: Excess function parameter 'txq' description in 'il_cmd_queue_free'
drivers/net/wireless/intel/iwlegacy/common.c:2932: warning: Function parameter or member 'il' not described in 'il_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:2932: warning: Function parameter or member 'q' not described in 'il_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:2932: warning: Function parameter or member 'slots' not described in 'il_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:2932: warning: Function parameter or member 'id' not described in 'il_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:2966: warning: Function parameter or member 'il' not described in 'il_tx_queue_alloc'
drivers/net/wireless/intel/iwlegacy/common.c:2966: warning: Function parameter or member 'txq' not described in 'il_tx_queue_alloc'
drivers/net/wireless/intel/iwlegacy/common.c:2966: warning: Function parameter or member 'id' not described in 'il_tx_queue_alloc'
drivers/net/wireless/intel/iwlegacy/common.c:3006: warning: Function parameter or member 'il' not described in 'il_tx_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:3006: warning: Function parameter or member 'txq_id' not described in 'il_tx_queue_init'
drivers/net/wireless/intel/iwlegacy/common.c:3245: warning: Function parameter or member 'il' not described in 'il_hcmd_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/common.c:3245: warning: Function parameter or member 'txq_id' not described in 'il_hcmd_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/common.c:3245: warning: Function parameter or member 'idx' not described in 'il_hcmd_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/common.c:3245: warning: Function parameter or member 'cmd_idx' not described in 'il_hcmd_queue_reclaim'
drivers/net/wireless/intel/iwlegacy/common.c:3279: warning: Function parameter or member 'il' not described in 'il_tx_cmd_complete'
drivers/net/wireless/intel/iwlegacy/common.c:3425: warning: Function parameter or member 'il' not described in 'il_init_geos'
drivers/net/wireless/intel/iwlegacy/common.c:3949: warning: bad line:
drivers/net/wireless/intel/iwlegacy/common.c:3955: warning: Function parameter or member 'il' not described in 'il_set_rxon_channel'
drivers/net/wireless/intel/iwlegacy/common.c:4154: warning: Function parameter or member 'il' not described in 'il_irq_handle_error'
drivers/net/wireless/intel/iwlegacy/common.c:5019: warning: Function parameter or member 'hw' not described in 'il_mac_config'
drivers/net/wireless/intel/iwlegacy/common.c:5019: warning: Function parameter or member 'changed' not described in 'il_mac_config'
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlegacy/common.c: In function ‘il_enqueue_hcmd’:
drivers/net/wireless/intel/iwlegacy/common.c:3126:6: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Linux Wireless <ilw@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-15-lee.jones@linaro.org
- Ensure spaces appear after {for, if, while, etc}
- Ensure spaces to not appear after '('
- Ensure spaces to not appear before ')'
- Ensure spaces appear between ')' and '{'
- Ensure spaces appear after ','
- Ensure spaces do not appear before ','
- Ensure spaces appear either side of '='
- Ensure '{'s which open functions are on a new line
- Remove trailing whitespace
There are still a whole host of issues with this file, but this
patch certainly breaks the back of them.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Benjamin Reed <breed@users.sourceforge.net>
Cc: Javier Achirica <achirica@users.sourceforge.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Fabrice Bellet <fabrice@bellet.info>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/cisco/airo.c: In function ‘airo_init_module’:
drivers/net/wireless/cisco/airo.c:5663:21: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Benjamin Reed <breed@users.sourceforge.net>
Cc: Javier Achirica <achirica@users.sourceforge.net>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Fabrice Bellet <fabrice@bellet.info>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/broadcom/b43/main.c: In function ‘b43_dummy_transmission’:
drivers/net/wireless/broadcom/b43/main.c:785:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
drivers/net/wireless/broadcom/b43/main.c: In function ‘b43_do_interrupt_thread’:
drivers/net/wireless/broadcom/b43/main.c:2017:3: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Martin Langer <martin-langer@gmx.de>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <m@bues.ch>
Cc: van Dyk <kugelfang@gentoo.org>
Cc: Andreas Jaggi <andreas.jaggi@waterwave.ch>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Cc: linux-wireless@vger.kernel.org
Cc: b43-dev@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-8-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/atmel/atmel.c:4232: warning: Cannot understand This file is part of net.russotto.AtmelMACFW, hereto referred to
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-6-lee.jones@linaro.org
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-4-allen.cryptic@gmail.com
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'wil' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'dbg' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'base' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'tbl' not described in 'wil6210_debugfs_init_offset'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-22-lee.jones@linaro.org
Returning PTR_ERR(NULL) means success, but we should return -ENOMEM.
Fixes: 1399fb87ea ("ath11k: register MHI controller device for QCA6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826113417.GE393664@mwanda
In ath11k_qmi_prepare_bdf_download(), ath11k_core_firmware_request() is
called, but the returned pointer is not checked for errors. Rather the
variable ret (which will always be zero) is checked by mistake. Fix
this and replace the various gotos with simple returns for clarity.
While we are at it, move the call to memset, as variable bd is not used
on all code paths.
Fixes: 7b57b2ddec ("ath11k: create a common function to request all firmware files")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200825143040.233619-1-alex.dewar90@gmail.com
The ath9k driver hides all LEDs related code behind CONFIG_MAC80211_LEDS
ifdefs so it does not really require the MAC80211_LEDS. The code builds
fine. Convert the "select" into "imply" to allow disabling LED trigger
when not needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820194049.28055-1-krzk@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:627:18: warning: ‘ar5416Bank7’ defined but not used [-Wunused-const-variable=]
627 | static const u32 ar5416Bank7[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:548:18: warning: ‘ar5416Bank3’ defined but not used [-Wunused-const-variable=]
548 | static const u32 ar5416Bank3[][3] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:542:18: warning: ‘ar5416Bank2’ defined but not used [-Wunused-const-variable=]
542 | static const u32 ar5416Bank2[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:536:18: warning: ‘ar5416Bank1’ defined but not used [-Wunused-const-variable=]
536 | static const u32 ar5416Bank1[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:462:18: warning: ‘ar5416Bank0’ defined but not used [-Wunused-const-variable=]
462 | static const u32 ar5416Bank0[][2] = {
| ^~~~~~~~~~~
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:553:18: warning: ‘ar5416Bank6’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9001_initvals.h:462:18: warning: ‘ar5416Bank6_9100’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-19-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9002_initvals.h:900:18: warning: ‘ar9280PciePhy_clkreq_off_L1_9280’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-18-lee.jones@linaro.org
The ath9k_htc driver hides all LEDs related code behind
CONFIG_MAC80211_LEDS ifdefs so it does not really require the
MAC80211_LEDS. The code builds and works just fine. Convert the
"select" into "imply" to allow disabling LED trigger when not needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820120444.8809-1-krzk@kernel.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-3-allen.cryptic@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath6kl/wmi.c: In function ‘ath6kl_wmi_bitrate_reply_rx’:
drivers/net/wireless/ath/ath6kl/wmi.c:1204:6: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-15-lee.jones@linaro.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-2-allen.cryptic@gmail.com
For whatever reason, when connected to an open/no-security BSS,
the wcn36xx controller in bmps mode does not forward 'wake-up'
beacons despite AP sends DTIM with station AID.
Meaning that AP is not able to wakeup the station and needs to wait
for the station to wakeup by its own (TX data, keep alive pkt...),
causing serious latency issues and unexpected deauth.
When connected to AP with encryption enabled, this issue does not occur.
So a simple workaround is to only enable bmps support in that case.
Ideally, it should be propertly fixed to allow bmps support with open
BSS, whatever the issue is at driver or firmware level.
Tested on wcn3620 and wcn3680.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598363127-26066-1-git-send-email-loic.poulain@linaro.org
By default, after associated to an AP, the wcn36xx bitrate adjustment
algorithm starts sending data at 1Mbps, and increases the rate slowly
(1Mbps, 2Mbps, 6Mbps...) over the further TX packets.
Starting at 1Mbps usually causes the initial throughput to be really
low and the maximum possible bitrate to be reached after about hundreed
of TX packets.
That can be improved by setting a different initial bitrate for data
packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this
value can be a legacy or MCS rate.
This patch sets the starting bitrate value to MCS-5, which seems to be
a good compromise given it can be quickly adjusted low or up if necessary.
(and based on what I observed in the wild with some mobile devices)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598345341-4505-1-git-send-email-loic.poulain@linaro.org
For software-driven scan, rely on mac80211 software scan instead
of internal driver implementation. The internal implementation
cause connection trouble since it keep the antenna busy during
the entire scan duration, moreover it's only a passive scanning
(no probe request). Therefore, let mac80211 manages sw scan.
Note: we fallback to software scan if firmware does not report
scan offload support or if we need to scan the 5Ghz band (currently
not supported by the offload scan...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
update tx power limits of channels 12, 13 for FCC
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200824084453.29953-1-yhchuang@realtek.com
This gives the added bonus of not wasting an extra udelay() if we're
timing out -- we double-check the register state one last time before
returning.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821235733.1785009-1-briannorris@chromium.org
I'm not a standards expert, but this really looks to be undefined
behavior, when chip->dig_cck may be NULL. (And, we're trying to do a
NULL check a few lines down, because some chip variants will use NULL.)
Fixes: fc637a860a ("rtw88: 8723d: Set IG register for CCK rate")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821211716.1631556-1-briannorris@chromium.org
When devm_clk_get() returns -EPROBE_DEFER, spi_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 854d66df74 ("staging: wilc1000: look for rtc_clk clock in spi mode")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820055256.24333-1-dinghao.liu@zju.edu.cn
When devm_clk_get() returns -EPROBE_DEFER, sdio_priv
should be freed just like when wilc_cfg80211_init()
fails.
Fixes: 8692b047e8 ("staging: wilc1000: look for rtc_clk clock")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820054819.23365-1-dinghao.liu@zju.edu.cn
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
The error message if 'pci_set_consistent_dma_mask()' fails is misleading.
The function call uses 32 bits, but the error message reports 64.
Moreover, according to the comment above 'dma_set_mask_and_coherent()'
definition, such an error can never happen.
So, simplify code, axe the misleading message and use
'dma_set_mask_and_coherent()' instead of 'dma_set_mask()' +
'dma_set_coherent_mask()'
While at it, make some clean-up:
- add # when reporting allocated length to be consistent between
functions
- s/consistent/coherent/
- s/unsigned int/u32/ to be consistent between functions
- align some code
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819071853.113185-1-christophe.jaillet@wanadoo.fr
The only usage of ath11k_thermal_ops is to pass its address to
thermal_cooling_device_register() which takes a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ops for reset_tid_config to support reset TID
configuration. This send default configuration to the
target for the TIDs and stores default value in the host.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-5-git-send-email-tamizhr@codeaurora.org
This patch add ops for set_tid_config to support TID
specific configuration. Station specific TID configuration
will have more priority than vif specific TID configuration.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT service flag introduced
to notify host for TID config support. And RTS_CTS extended tid
configuration support advertised through the service flag
WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT.
TID specific noack configuration requires
aggregation should be disabled and rate for the data TID packets
should be basic rates. So, if the TID already configured
with noack policy then driver will ignore the aggregation
or TX rate related configuration for the same data TID.
In TX rate configuration should be applied with highest
preamble configuration(HT rates should not be applied
for the station which supports vht rates).
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-4-git-send-email-tamizhr@codeaurora.org
This patch adds WMI interface to configure station specific
TID configuration . Host needs to send station's MAC address
along with TID number and its configuration to target through
WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT flag is added to advertise
this support.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-2-git-send-email-tamizhr@codeaurora.org
When firmware crashes it's possible to create a coredump for later analysis,
add support to collect the register and memory info from SDIO devices.
The coredump configuration is different between QCA6174 PCI and QCA6174 SDIO,
so add specific registers and memory regions for the latter.
QCA6174 SDIO has two methods to dump the firmware: fastdump and slowdump.
Fastdump is not supported in olded versions of firmware, and for these ath10k
will automatically select slowdump. If firmware supports fastdump, ath10k will
automatically select it. QCA6174 SDIO firmware version
WLAN.RMH.4.4.1-00017-QCARMSWPZ-2 is the first version supporting fastdump.
For slowdump, ath10k_sdio_hif_diag_read() can not be used as the diag
window has a limit value, it is 4 bytes and the dump's buffer length is larger
than it, it will trigger error. So this patch adds ath10k_sdio_read_mem() to
read 4 bytes for each time.
Example output of a firmware crash:
ath10k_sdio mmc1:0001:1: simulating soft firmware crash
ath10k_sdio mmc1:0001:1: firmware crashed! (guid 413d98b1-84c0-4298-b605-2b10ec0c54a5)
ath10k_sdio mmc1:0001:1: qca6174 hw3.2 sdio target 0x05030000 chip_id 0x00000000 sub 0000:0000
ath10k_sdio mmc1:0001:1: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 1
ath10k_sdio mmc1:0001:1: firmware ver WLAN.RMH4.4.1-00126-QCARMSWP-1 api 6 features wowlan,ignore-otp,raw-mode crc32 b84317cf
ath10k_sdio mmc1:0001:1: board_file api 2 bmi_id 0:4 crc32 6364cfcc
ath10k_sdio mmc1:0001:1: htt-ver 3.69 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
ath10k_sdio mmc1:0001:1: firmware register dump:
ath10k_sdio mmc1:0001:1: [00]: 0x05030000 0x000015B3 0x0099908D 0x00955B31
ath10k_sdio mmc1:0001:1: [04]: 0x0099908D 0x00060730 0x00000018 0x004641A0
ath10k_sdio mmc1:0001:1: [08]: 0x0041FAA4 0x0041FA9C 0x00999070 0x00404490
ath10k_sdio mmc1:0001:1: [12]: 0x00000009 0xFFFFFFFF 0x00952CD0 0x00952CE6
ath10k_sdio mmc1:0001:1: [16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [20]: 0x4099908D 0x0040E9E8 0x00000001 0x00423AC0
ath10k_sdio mmc1:0001:1: [24]: 0x809F3189 0x0040EA48 0x00426240 0xC099908D
ath10k_sdio mmc1:0001:1: [28]: 0x809143A7 0x0040EA68 0x0041FAA4 0x00423A80
ath10k_sdio mmc1:0001:1: [32]: 0x809F1193 0x0040EA88 0x00411770 0x004117E0
ath10k_sdio mmc1:0001:1: [36]: 0x809F0EEE 0x0040EAA8 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [40]: 0x80911210 0x0040EAC8 0x00000008 0x00404130
ath10k_sdio mmc1:0001:1: [44]: 0x80911154 0x0040EB28 0x00400000 0x00000000
ath10k_sdio mmc1:0001:1: [48]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
ath10k_sdio mmc1:0001:1: [52]: 0x40910024 0x0040EB78 0x0040AB98 0x0040AB98
ath10k_sdio mmc1:0001:1: [56]: 0x00000000 0x0040EB98 0x009BB001 0x00040020
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-3-git-send-email-wgong@codeaurora.org
For some hw version, it has more than one bus type, it need to add bus
type to distinguish different chip.
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-2-git-send-email-wgong@codeaurora.org
The 4329 throughput drops from 40.2 Mbits/sec to 190 Kbits/sec in 2G
11n mode because the commit b41c232d33 ("brcmfmac: reserve 2 credits
for host tx control path"). To fix the issue, host driver only reserves
tx control credit when there is a txctl frame is pending to send. And
we also check available credit by using "not equal to 0" instead of
"greater than 0" because tx_max and tx_seq are circled positive numbers.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: b41c232d33 ("brcmfmac: reserve 2 credits for host tx control path")
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813070017.89023-1-wright.feng@cypress.com
ath.git patches for v5.10. Major changes:
ath11k
* add support for QCA6390 PCI devices
wcn36xx
* add support for TX ack
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
clang static analysis reports this problem
rndis_wlan.c:3147:25: warning: Assigned value is garbage or undefined
wiphy->max_num_pmkids = le32_to_cpu(caps.num_pmkids);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The setting of caps happens here, with a call to rndis_query_oid()
retval = rndis_query_oid(usbdev,
if (retval >= 0) {
Reviewing rndis_query_oid() shows that on success 0 is returned,
failure is otherwise. So the retval check is not tight enough.
So tighten the retval check. Similar problem in
rndis_wlan_get_caps().
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200811140219.8412-1-trix@redhat.com
A possible call chain is as follow:
mwifiex_sdio_interrupt (sdio.c)
--> mwifiex_main_process (main.c)
--> mwifiex_process_cmdresp (cmdevt.c)
--> mwifiex_process_sta_cmdresp (sta_cmdresp.c)
--> mwifiex_ret_802_11_scan (scan.c)
--> mwifiex_parse_single_response_buf (scan.c)
'mwifiex_sdio_interrupt()' is an interrupt function.
Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.
So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.
Fixes: 7c6fa2a843 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Clang static analysis reports this error
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803e ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com
When STBC is enabled, NSTS_SU value need to be accounted for VHT NSS
calculation for SU case.
Without this fix, 1SS + STBC enabled case was reported wrongly as 2SS
in radiotap header on monitor mode capture.
Tested-on: QCA9984 10.4-3.10-00047
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392971-3897-1-git-send-email-murugana@codeaurora.org
As a part of device shutdown the smmu driver will be
stopped and henceforth any IOVA address translation
will not be done. The wlan driver, being one of the
smmu driver consumer, should stop all the dma related
activity as a part of shutdown, and thereby ensuring
that no dma activity is done once the smmu driver
shuts down.
During the device shutdown, the smmu calls shutdown
for all its consumers in order to indicate them to
stop all their dma activities.
Register the shutdown handler to stop the wlan
driver and avoid any dma operations.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593193981-30161-1-git-send-email-pillair@codeaurora.org
For QCA6390, normal power up and power down can't bring MHI
to a workable state. This happens especially in warm reboot
and rmmod and insmod. Host needs to write a few registers to
bring MHI to normal state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeauroro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-10-git-send-email-kvalo@codeaurora.org
For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.
Add MISC_CAPS_TCL_0_ONLY to control it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org
For QCA6390, the num_radios is 1 but it needs to process 2 lmac rings.
So use NUM_RXDMA_PER_PDEV to do another loop.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-8-git-send-email-kvalo@codeaurora.org
QCA6390 doesn't enable V2 map and ummap event, so the addr search
flags and type is different from IPQ8074. Assign correct search flags
and type for QCA6390.
Without this change, ping sometimes fails. With this change, now ping
is always successful.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-7-git-send-email-kvalo@codeaurora.org
For QCA6390 firmware, bss peer must be created before vdev_start, so delay
vdev_start until bss peer is created.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-6-git-send-email-kvalo@codeaurora.org
For QCA6390, it processes the reg chan list event only for phy0,
and it goes to fallback if the phy_id is not valid. For a valid
phy_id but not 0, just discard the event.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-5-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
For QCA6390, it has 2 lmacs and thus 2 rxdmas. However, each rxdma has rxdma0
only, and doesn't have rxdma1. So for QCA6390, don't initialize rxdma1 related
rings such as rx_mon_buf_ring, rx_mon_dst_ring and rx_mon_desc_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-3-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org
For QCA6390, it uses peer_map and peer_unmap V1. IPQ8074 uses V2.
Redefine previous definition to peer_map2 and peer_unmap2.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-13-git-send-email-kvalo@codeaurora.org
For QCA6390, host puts hardware to Dual Band Simultaneous (DBS) mode by default
so both 2G and 5G bands can be used. Otherwise only the 5G band can be used.
QCA6390 doesn't provide band_to_mac configuration and firmware will do the
band_to_mac map.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-12-git-send-email-kvalo@codeaurora.org
QCA6390 has very different wmi config parameters compared to IPQ8074,
so use different function to initialize wmi init config parameters.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-11-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and only one HW is registered to
mac80211. This one pdev manages both 2G radio and 5G radio.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-10-git-send-email-kvalo@codeaurora.org
Disable CE interrupt otherwise interrupt may come before host
initialized related context. This also fixes unbalanced interrupt
enablement.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-9-git-send-email-kvalo@codeaurora.org
Move function to get msi_addr and msi_data before srng setup,
otherwise srng is setup with no MSI configuration.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-8-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt so it needs msi_addr and msi_data
to generate interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-7-git-send-email-kvalo@codeaurora.org
This macro is evil as it's accesses ab variable in a hidden way. It's better
for readibility to access ab->hw_params.ce_count directly.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-6-git-send-email-kvalo@codeaurora.org
This macro is evil as it's accesses ab variable in a hidden way. It's better
for readibility to access ab->hw_params.host_ce_config directly.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-5-git-send-email-kvalo@codeaurora.org
QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.
The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org
Now some of the HAL register macros access ab variable in a hidden way, make ab
variable visible in the macro by adding it as an argument.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-3-git-send-email-kvalo@codeaurora.org
QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org
There's no reason to have call for enable_pll_clk in ath10k_bmi_start(), move
it to ath10k_core_start() instead. This way it's possible to call
ath10k_bmi_start() from sdio.c during firmware dump creation. And also the
function call is more visible when it's in core.c.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597421745-4329-1-git-send-email-kvalo@codeaurora.org
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()'.
Fixes: 1863008369 ("ath10k: fix shadow register implementation for WCN3990")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802122227.678637-1-christophe.jaillet@wanadoo.fr
The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.
This is similar to a bug that syzkaller found in commit e4ff08a4d7
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda
The ath9k driver was so far only able to rekey PTK0 keys correctly due
to the best effort queue flush added with commit 62872a9b9a
("mac80211: Fix PTK rekey freezes and clear text leak").
Add the needed queue flush and set NL80211_EXT_FEATURE_CAN_REPLACE_PTK0
to tell mac80211 that the driver can now rekey PTK0 keys correctly and
no longer needs the best effort flush.
Effectively this prevents mac80211 to warn when rekeying a PTK0 key
only.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200804164152.175375-1-alexander@wetzel-home.de
The value for "aid" comes from skb->data so Smatch marks it as
untrusted. If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().
Fixes: 572e27c00c ("ath6kl: Fix AP mode connect event parsing and TIM updates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/base.c:1111: warning: Function parameter or member 'ah' not described in 'ath5k_drain_tx_buffs'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@winlab.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-21-lee.jones@linaro.org
No effort has been made to document any of the function parameters here.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_ies' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_len' not described in '_wil_cfg80211_merge_extra_ies'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/pcu.c:115: warning: Function parameter or member 'band' not described in 'ath5k_hw_get_frame_duration'
drivers/net/wireless/ath/ath5k/pcu.c:955: warning: Excess function parameter 'mode' description in 'ath5k_hw_pcu_init'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Reyk Floeter <reyk@openbsd.org>
Cc: "W. S. Bell" <mentor@madwifi.org>
Cc: Luis Rodriguez <mcgrof@winlab.rutgers.edu>
Cc: Pavel Roskin <proski@gnu.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-10-lee.jones@linaro.org
On QCA6390 reg_start and reg_size values are different from IPQ8074 so we need
to change the values runtime. As we can't modify a static const variable
hw_srng_config directly, instead use it as a template, copy it and modify the
copy with correct values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-12-git-send-email-kvalo@codeaurora.org
On x86 and other non-qcom platforms, host needs to explicitly tell the firmware
to use the internal sleep clock. Some QCA6390 modules have OTP burnt with
external sleep clock selected, and these modules can't work expectedly unless
firmware selects internal sleep clock.
Add a field to hw_params to support this difference.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-11-git-send-email-kvalo@codeaurora.org
It's caused by reading memory out of boundary from target_ce_config_wlan.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-10-git-send-email-kvalo@codeaurora.org
The decoded_size is wrongly assigned in ath11k_qmi_msg_handlers and it results
in out of boundary access in qmi_decode. The correct decoded_size should be
calculated from the related ind_msg structure.
This issue is exposed with QCA6390 because it needs 11 small memory chunks
which are stored in qmi_wlanfw_request_mem_ind_msg_v01 and hence the
decoded_size exceeds the wrongly assigend decoded_size.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-9-git-send-email-kvalo@codeaurora.org
On x86 it's sometimes difficult to allocate a large contigous DMA
memory, so instead allocate blocks of small chunk memory.
In ath11k_qmi_msg_mem_request_cb() the error handling was cleaned up to avoid
an unused variable warning. Also changed the test from (ret < 0) to just (ret)
as the functions don't return any positive values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-8-git-send-email-kvalo@codeaurora.org
CE srng is used for control path and CE srng processing is done using tasklet
bottom half. Setup ce tasklet initialization and scheduling for control path.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-7-git-send-email-kvalo@codeaurora.org
Fill msi base address and msi data to be programmed in CE srang.
This is used by the srng to generate the msi interrupt.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-6-git-send-email-kvalo@codeaurora.org
QMI service instance id is used for qmi service lookup, IPQ8074 and QCA6390
uses different instance id for service lookup. Fill appropriate QMI service
instance id for respective targets.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-4-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.
Add support to create board name for different targets. This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.
As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.
At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org
QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org
Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.
Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org
This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org
Add support for setting up pci region and dma mask.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-6-git-send-email-kvalo@codeaurora.org
QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org
This is needed for splitting ahb and pci modules as they have different ring
mask settings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org
Define own firmware directory and settings for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org
With only IPQ8074 supported ath11k was only usable on Qualcomm architectures.
But now that we are adding QCA6390 PCI support to ath11k that's not the case
anymore and it can be used on any architecture supporting PCI. So remove the
dependency on ARCH_QCOM. After that there is also no need to depend on
COMPILE_TEST.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-2-git-send-email-kvalo@codeaurora.org
The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.
The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.
It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.
This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.
This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
When using QCA6174 PCI devices working in station mode, after connected
to AP, tx bitrate is always '1.0 MBit/s' in output of command 'iw wlan0
station dump'. (QCA6174 SDIO devices are working fine.)
After this patch, it show correct bitrate:
Station c4:04:15:5d:97:22 (on wls1)
inactive time: 312 ms
rx bytes: 31496
rx packets: 173
tx bytes: 8625
tx packets: 46
tx retries: 0
tx failed: 0
signal: -76 [-88, -80] dBm
signal avg: -75 [-82, -77] dBm
tx bitrate: 39.0 MBit/s MCS 4
rx bitrate: 26.0 MBit/s MCS 3
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-4-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES
This patch not effect the info of above 4 bit for all hardware, reason
as below:
NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.
NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.
NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.
If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
The ioreadX() helpers have inconsistent interface. On some architectures
void *__iomem address argument is a pointer to const, on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200709072837.5869-3-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719104041.57916-1-grandmaster@al2klimov.de
list_for_each_entry{_safe} is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry{_safe} is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry{_safe}, the element obtained
by list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change for the list_for_each_entry
case is as follows: (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595761112-11003-8-git-send-email-Julia.Lawall@inria.fr
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
Typo "destoy" made me wonder if correct patch is wrong; fix it. No
functional change.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724083910.GA31930@amd
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719105052.57997-1-grandmaster@al2klimov.de
Merge misc updates from Andrew Morton:
- a few MM hotfixes
- kthread, tools, scripts, ntfs and ocfs2
- some of MM
Subsystems affected by this patch series: kthread, tools, scripts, ntfs,
ocfs2 and mm (hofixes, pagealloc, slab-generic, slab, slub, kcsan,
debug, pagecache, gup, swap, shmem, memcg, pagemap, mremap, mincore,
sparsemem, vmalloc, kasan, pagealloc, hugetlb and vmscan).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
mm: vmscan: consistent update to pgrefill
mm/vmscan.c: fix typo
khugepaged: khugepaged_test_exit() check mmget_still_valid()
khugepaged: retract_page_tables() remember to test exit
khugepaged: collapse_pte_mapped_thp() protect the pmd lock
khugepaged: collapse_pte_mapped_thp() flush the right range
mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible
mm: thp: replace HTTP links with HTTPS ones
mm/page_alloc: fix memalloc_nocma_{save/restore} APIs
mm/page_alloc.c: skip setting nodemask when we are in interrupt
mm/page_alloc: fallbacks at most has 3 elements
mm/page_alloc: silence a KASAN false positive
mm/page_alloc.c: remove unnecessary end_bitidx for [set|get]_pfnblock_flags_mask()
mm/page_alloc.c: simplify pageblock bitmap access
mm/page_alloc.c: extract the common part in pfn_to_bitidx()
mm/page_alloc.c: replace the definition of NR_MIGRATETYPE_BITS with PB_migratetype_bits
mm/shuffle: remove dynamic reconfiguration
mm/memory_hotplug: document why shuffle_zone() is relevant
mm/page_alloc: remove nr_free_pagecache_pages()
mm: remove vm_total_pages
...
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
- Add a new host cap bit and a corresponding DT property, to support power
cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host:
- Convert a few DT bindings to the json-schema
- mtk-sd: Add support for command queue through cqhci
- mtk-sd: Add support for the MT6779 variant
- renesas_sdhi_internal_dmac: Fix dma unmapping in the error path
- sdhci_am654: Add support for the AM65x PG2.0 variant
- sdhci_am654: Extend support for phys/clocks
- sdhci-cadence: Drop incorrect HW tuning for SD mode
- sdhci-msm: Add support for interconnect bandwidth scaling
- sdhci-msm: Enable internal voltage control
- sdhci-msm: Enable low power state for pinctrls
- sdhci-of-at91: Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli: Improve clock handling for GL975x
- sdhci-pci-o2micro: Add HW tuning for SDR104 mode
- sdhci-pci-o2micro: Fix support for O2 host controller Seabird1
-----BEGIN PGP SIGNATURE-----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=AwwR
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfKUIHAAoJEG4XJFUm622bXqkH/jgjKWh4b96Pv56jLPtyoPKj
q9ZvIS1MFhfeY/DFX2gAx34iOwDi7lRVsb1r8IX+rui+B4yTDkvgM2azduSfUpA7
+WOHaQdRYMbUa0YlvotaxFaHpqABKFnRd3zQKTMgT3LyVgj6OMiyHhc7DJTrBvMM
KR+Z6/aNmMccWcSR4OPPF8zPRmp7h5yLW55UgqfOm0JzRfCnXtq6vb6MUDxYelGm
ruvKP2W86m0DfQzPSwCEdSPkD/2aspi9HrMJNXm/cNqGk6AFQTZzPpQC6PowSrWA
9rpzBRti2OwDD6Q6QJqmWzQ8pclP4BMZWPyYBqaC8tTHDvD13OV/siZVk9nP+As=
=KOz+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mt76 driver had major conflicts within mt7615 directory. To make it easier for
every merge wireless-drivers to wireless-drivers-next and solve those
conflicts.
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721112302.22718-1-nsaenzjulienne@suse.de
wl1251_event_ps_report() should not always return 0 because
wl1251_ps_set_mode() may fail. Change it to return 'ret'.
Fixes: f7ad1eed4d ("wl1251: retry power save entry")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730073939.33704-1-wanghai38@huawei.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200728114128.1218310-1-vaibhavgupta40@gmail.com
In some Intersil files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723135254.594984-1-f.suligoi@asem.it
Add the missing platform_device_unregister() before return from
qtnf_core_mac_alloc() in the error handling case.
Fixes: 616f5701f4 ("qtnfmac: assign each wiphy to its own virtual platform device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200730064910.37589-1-wanghai38@huawei.com
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'ipw2100_msg_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_msg_allocate
Moreover, 'ipw2100_msg_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'status_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> status_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'bd_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> bd_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw2100_tx_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
Moreover, 'ipw2100_tx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw_queue_tx_init()' (ipw2200.c),
GFP_KERNEL can be used because it is called from a call chain that already
uses GFP_KERNEL and no spin_lock is taken in the between.
The call chain is:
ipw_up
--> ipw_load
--> ipw_queue_reset
--> ipw_queue_tx_init
'ipw_up()' already uses GFP_KERNEL for some other memory allocations.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101716.26185-1-christophe.jaillet@wanadoo.fr
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
No lock is taken in the between.
So it is safe to use GFP_KERNEL in 'ipw2100_tx_allocate()'.
BTW, 'ipw2100_queues_allocate()' also calls 'ipw2100_msg_allocate()' which
already allocates some memory using GFP_KERNEL.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200722101701.26126-1-christophe.jaillet@wanadoo.fr
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721150547.371763-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719111124.58167-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719110115.58085-1-grandmaster@al2klimov.de
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718100240.98593-1-grandmaster@al2klimov.de
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
The callbacks make use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device() and
pci_set_power_state() to do required operations. In generic mode, they are
no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
The .suspend() callback is invoking rt2x00lib_suspend() which needs to be
modified as generic rt2x00pci_suspend() has no pm_message_t type argument,
passed to it, which is required by it according to its declaration.
Although this variable remained unused in the function body. Hence, remove
it from the function definition & declaration.
rt2x00lib_suspend() is also invoked by rt2x00usb_suspend() and
rt2x00soc_suspend(). Thus, modify the functional call accordingly in their
function body.
Earlier, .suspend() & .resume() were exported and were used by the
following drivers:
- drivers/net/wireless/ralink/rt2x00/rt2400pci.c
- drivers/net/wireless/ralink/rt2x00/rt2500pci.c
- drivers/net/wireless/ralink/rt2x00/rt2800pci.c
- drivers/net/wireless/ralink/rt2x00/rt61pci.c
Now, we only need to bind "struct dev_pm_ops" variable to
"struct pci_driver". Thus, make the callbacks static. Declare an
"extern const struct dev_pm_ops" variable and bind PM callbacks to it. Now,
export the variable instead and use it in respective drivers.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717110928.454867-1-vaibhavgupta40@gmail.com
Moved macros used for Vendor/Device ID from wilc1000 driver to common
header file and changed macro name for consistency with other macros.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717051134.19160-1-ajay.kathat@microchip.com
In the implementation of mt7601u_mcu_msg_send(), skb is supposed to be
consumed on all execution paths. Release skb before returning if
test_bit() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200718052630.11032-1-navid.emamdoost@gmail.com
Missing this firmware is not fatal, my wifi card still works. Even more,
I couldn't find any documentation what it is or where to get it. So, I
don't think the users should be notified if it is missing. If you browse
the net, you see the message is present is in quite some logs. Better
remove it.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200625165210.14904-1-wsa@kernel.org
Without this patch, RTL8821CE will not have coex support,
and will crash the system because of the NULL pointers
for the coex functions.
While RTL8822C series are WiFi + BT combo chips, it needs
the co-existence mechanism for the device to work on both
WiFi and BT without interfering each other. And the coex
support has already been added before, most of the mechanisms
are implemented. The driver should just add corresponding
functions to operate on different types of chips and its
coex parameters.
Fixes: f745eb9ca5 ("rtw88: 8821c: Add 8821CE to Kconfig and Makefile")
Signed-off-by: Ping-Cheng Chen <pc.chen@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724054208.31115-1-yhchuang@realtek.com
The sparse tool complains as follows:
drivers/net/wireless/realtek/rtw88/rtw8821c.c:1374:32: warning:
symbol 'rtw8821c_rtw_pwr_track_tbl' was not declared. Should it be static?
This variable is not used outside of rtw8821c.c, so this commit
marks it static.
Fixes: 3a4312828c ("rtw88: 8821c: add power tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721134901.33968-1-weiyongjun1@huawei.com
It's very useful to send H2C command for debug usage. Add an entry
for sending H2C command to firmware.
usage example:
echo 42,00,00,43,02,00,00,00 > /sys/kernel/debug/ieee80211/phyX/rtw88
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-8-yhchuang@realtek.com
Sometimes mac80211 will just ask driver to change the interface
instead of to remove and then add a new one. And for driver, to
change the interface is just simply to remove and add a new one
but change the type of it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-6-yhchuang@realtek.com
The coex mechanism used to skip upon the freeze flag is raised.
That will cause the coex mechanism being skipped unexpectedly.
Coex only wanted to keep the TDMA table from being changed by
BT side.
So, check the freeze and reason, if the coex reason is coming
from BT info, skip it, to make sure the coex triggered by Wifi
itself can work.
This is required for the AP mode, while the control flow is
different with STA mode. When starting an AP mode, the AP mode
needs to start working immedaitely after leaving IPS, and the
freeze flag could be raised. If the coex info is skipped, then
the AP mode will not set the antenna owner, leads to TX stuck.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-5-yhchuang@realtek.com
Previous settings for TX descriptors of and reserved page packets
are insufficient.
For the sequence number of packets downloaded to reserved page, it
should be filled by hardware.
And for ps-poll packets in reserved page, to prevent AID being
changed by hardware, NAVUSEHDR should be set.
Additionally, the rate should be adjusted based on the current band
for mgmt and reserved page packets.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-4-yhchuang@realtek.com
Fix the transmission is not sent with short GI under
some conditions even if the receiver supports short GI.
If VHT capability IE exists in the beacon, the original
code uses the short GI for 80M field as driver's short GI
setting for transmission, even the current bandwidth is
not 80MHz.
Short GI supported fields for 20M/40M are informed in HT
capability information element, and short GI supported
field for 80M is informed in VHT capability information
element.
These three fields may be set to different values.
Driver needs to record each short GI support field for
each bandwidth, and send correct info depends on current
bandwidth to the WiFi firmware.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-3-yhchuang@realtek.com
Convert the type of LDPC field to boolen because
LDPC field of RA info H2C command to firmware
is only one bit.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-2-yhchuang@realtek.com
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions as through
the generic framework, PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200721125514.145607-1-vaibhavgupta40@gmail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719121224.58581-1-grandmaster@al2klimov.de
The variables ant_num and single_ant_path are being initialized with a
value that is never read and are being updated later with a new value.
The initializations are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723163214.995226-1-colin.king@canonical.com
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
-----BEGIN PGP SIGNATURE-----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=FR6T
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfGukwAAoJEG4XJFUm622bIdwIAKYV3lplb6mXyDdF1b3Yoxar
0IDUglXlJN+VIgvUQG4wOvxgDw7jp6q95BRi58VjafIFm+orjILvYFmwThLPYfIS
dA0ML9+zGnRMC+SIjZktXKG9lridQXyqexWHCFF9dT147GsF8+LIbfqT6denCLf7
vP26RSMAMK5Ed01V9qb5rtitaVbr+Bx+c7adV8tLH/gkWeTEp4CaDhNOkMJ0uRCV
QPZ8duF1Hz/QVMn9PAA8xGTH4bxIfSfWVJfSjG1uq349CZ+MjHleDeYWKh524ThV
49YTabR2DIKOWSgNzG7jsitz7K/420Y/NpuNeGWO+7czgYe2uEIrGDZkYPUPoS4=
=PTR1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of __mt76x02u_mcu_send_msg() the skb is consumed
all execution paths except one. Release skb before returning if
test_bit() fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free the second mcu skb if __mt76_mcu_skb_send_msg() fails to transmit
the first one in mt7615_mcu_wtbl_sta_add().
Fixes: 99c457d902 ("mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid possible overflows, move tx queue accounting from
mt7663s_tx_run_queue() to mt76s_tx_queue_skb_raw()/mt76s_tx_queue_skb()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7663s 802.11ac 2x2:2 chipset to mt7615 driver.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_sdio module as common layer to add mt7663s support
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7663-usb-sdio-common module as container for shared
code between usb and sdio driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As usb, sdio relies on mt76 workqueue to configure tx rate or upload
keys to the hw. This is a preliminary patch to add SDIO support to
mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_skb_adjust_pad to reuse the code adding sdio support to
mt7615 driver and remove code duplication. Move 4B header configuration
for usb devices out of mt76_skb_adjust_pad
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
usb and sdio relies on SF architecture. This is a preliminary patch to
add SDIO support to mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Smatch complains that "wcidx" value comes from the network and thus
cannot be trusted. In this case, it actually seems to come from the
firmware. If your wireless firmware is malicious then probably no
amount of carefulness can protect you.
On the other hand, these days we still try to check the firmware as much
as possible. Verifying that the index is within bounds will silence a
static checker warning. And it's harmless and a good exercise in kernel
hardening. So I suggest that we do add a bounds check.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix potential memory leak in mcu message handler on error condition.
Fixes: 0e6a29e477 ("mt76: mt7615: add support to read temperature from mcu")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix potential memory leak in mcu message handler on error condition.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix memory leak in set key.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reschedule runtime-pm delayed work if there is a new activity when ps
delayed work is already scheduled
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not schedule ps_work during hw scanning or hw scheduled frequency
scan
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On usb device rate configuration for sampling is performed relying on a
workqueue since it is not possible to access the device in the interrupt
context. Move the configuration of the probe_rate flag in the workqueue
in order to keep probe sampling in sync with actual rate configuration
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_driver_own can fail if it runs too close to mt7615_fw_own. In
order to improve mt7615_driver_own reliability, retry to get runtime-pm
ownership if mt7615_driver_own fails
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce idle-timeout knob in mt7615 debugfs in order to configure the
idle time to switch to low-power state
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to reduce number of received interrupts and power consumption,
enable hw beacon filter if runtime-pm is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce runtime-pm knob in mt7615 debugfs in order to enable/disable
runtime pm available in offload firmware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check MT76_STATE_PM in mt7615_driver_own/mt7615_firmware_own
in order to not requested power ownership if it is already granted
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Double-check if the device is in low-power state before accessing
registermap in mt7615_sta_rate_tbl_update() and in
mt7615_led_set_config()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt7615_pm_wake()/mt7615_pm_power_save_sched() directly in order to
wake the device from low power state in mt7615_mac_sta_{add,remove}
since they run holding mt76 mutex in common mt76 code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Queue frames pushed by mac80211 running mt7615_tx if the device is
low-power state. Run wake workqueue in order to swicth to full-power
before transmitting pending frames
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure the device is in full-power before pulling frames from
mac80211 queues
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure to run mt7615_mcu_set_roc() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure to run mt7615_mcu_set_wmm() holding mt76 mutex in order to
wake the device from low power state and avoid races
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure to run mt7615_dfs_init_radar_detector in mt7615_regd_notifier
holding mt76 mutex in order to avoid races and set the device in full
power
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set device in full power before performing hw scan or hw scheduled scan
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure to wake the device in mt7615_pci_suspend in order to properly
configure device registers before suspend
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_update_survey utility routine in order to compute
survey stats without waking up the device since it runs holding mt76 lock.
Run mt7615_pm_wake directly in mt7615_update_channel since it can run
with mt76.mutex held if called by mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce runtime-pm power_save delayed work used to enable
low-power after an inactivity period
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure the device is in full-power before uploading keys to the hw
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure the device is in full-power before reading regs in debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mutex_{acquire,release} utility routines in order to
switch in full-power/low-power before/after accessing device register-map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_pm_wake utility routine to wake the device from
runtime low-power state (lower-power state is currently supported by
offload firmware for pcie devices).
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76 workqueue from usb to common code in order to be reused adding
low-power support for mt7663 chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to the vendor sdk, mt7663 does not need to poll register after
firmware own. Since just mt7622 polls status register, set proper
timeout value according to the vendor sdk
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoid memcpy in Rx hot path to slightly improve performance.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable support for HC-M7662BU1 module on mt76x2u driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings, as well as displaying
rx statistics.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used for calibration in the manufacturing process.
It supports sending a configurable number of packets with a specific rate
and configurable tx power levels / antenna settings.
It also supports receiving packets and showing some statistics, including
packet counters and detailed RSSI information.
It will only be compiled in if CONFIG_NL80211_TESTMODE is enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All drivers use this in pretty much the same way. Moving it to core helps with
some checks for the upcoming testmode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that the bus access functions can use mapping for accessing full
register addresses, use it for WF_PHY registers to keep them constant.
Needed for follow-up work on testmode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unlike on earlier chips, DMA completion on MT7615 does not imply actually
having sent out any packets.
Since AQL will prevent filling the hardware queues and will only allow more
packets to be passed to the driver after tx completion, it makes much more
sense to schedule the tx tasklet there.
This is also needed for scheduling tx in testmode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76x2e prefix in mt76x2/pci.c and align to the rest of
mt76 code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw/fw
support always txq (altxq) in order to be in sync with mac txwi code
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is easy to add MU EDCA parameters in the future. This patch
also fixes a wrong cw_min assignment.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable MU-MIMO DL/UL and add relative counters in debugfs.
Currently MU modules read WTBL first to notify BA changes to
other cross modules, so adjust mt7915_mcu_sta_ba() accordingly.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In MT7915, hardware queue map is flexible. However, certain firmware modules
like MU and U-APSD presume a fixed queue order to adapt some devices that have
DMA scheduler with a strict order, so this patch can help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce U-APSD support in mt76 driver for AP interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For consistency with the rest of the code always rely on defined
macros for register access
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
kernel test robot <lkp@intel.com> found the following issue
and Kalle Valo forwarded it to Linux wireless.
drivers/net/wireless/mediatek/mt76/pci.c:8:6:
warning: no previous prototype for 'mt76_pci_disable_aspm'
Fix this by adding the missing include of mt76.h as Kalle
suggested.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
While looking at the ETSI regulatory domain definitions
and a patch, which allows more channels for ath10k, I also
checked the channels allowed for mt76.
ETSI regulations would possibly allow to add channels 32, 68,
96, 144, 169 and 173. IEEE 802.11-2016 defines no operating class
for channels 32, 68 and 96. This leaves us channels 144, 169 and 173,
which are included in this patch.
I tested 169 and 173 with a mt76 based USB dongle (AVM AC 860) and they
worked fine. If I saw that right, these channels are also covered by
register definitions inside the driver.
Channel 144 should also work, but gets disabled by the kernel as of now.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix up typo in Kconfig with indicating MT7663U is an 802.11ac device
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_for_each_q_rx whenever possible in order to simply the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfFWQeAAoJEG4XJFUm622bVAwH/3r2oR+NS1kNDNGi9nrLAIav
trLgPa2VbgPVgTcwIckfvZFl6BK9zo1KG6u6jYp45C6uNBJNESjarf8aLAXvXdFt
t0yBkb6OCUq+efoOFbxV2im6ER57aN27POsn74xrCeR3fwZgY9QSHRMjQ5x1tjWH
JdVatT6jtu2LuxsTjfS0K5kjeuyE0vE1iCUlsQ5qwcSLODGa9u7ydheoNcLOHvss
ACun8zXvWqJhTar+iJHiTJTWyQPE6es0V1SAw0RnTuLRRmtv/Q9Zx4YOH2d3JkOC
55mfgO3uNzw8fcJ5hoILHtXxhI2qtSkdydIFbE1U9CgBKE39Uo0VgFf9fl6VJRg=
=7a5a
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-2-refactormyself@gmail.com
Fix the regression introduced by commit c8685937d0 ("iwlwifi: move
pu devices to new table") by adding the ids and the configurations of
two missing Killer 1550 cards in order to configure and let them work
correctly again (following the new table convention).
Resolve bug 208141 ("Wireless ac 9560 not working kernel 5.7.2",
https://bugzilla.kernel.org/show_bug.cgi?id=208141).
Fixes: c8685937d0 ("iwlwifi: move pu devices to new table")
Signed-off-by: Alessio Bonfiglio <alessio.bonfiglio@mail.polimi.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200714091911.4442-1-alessio.bonfiglio@mail.polimi.it
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-3-refactormyself@gmail.com
The variable tid is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701135221.549700-1-colin.king@canonical.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-3-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-2-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
In the case of adm8211, after removing PCI helper functions, .suspend()
and .resume() became empty-body functions. Hence, define them NULL and
use dev_pm_ops.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629035031.169670-1-vaibhavgupta40@gmail.com
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves. The required operations are
done by PCI core.
PCI drivers are not expected to invoke PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_set_power_state(), etc. Their tasks are completed by PCI core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624174048.64754-1-vaibhavgupta40@gmail.com
Earlier, drivers had to manage the device's power states, and related
operations, themselves. With the generic approach, these are done by PCI
core.
The only driver-specific jobs, .suspend() and .resume() doing were invoking
PCI helper functions pci_save/restore_state() and
pci_set_power_state(). This is not recommeneded as PCI core takes care of
that. Hence they became empty-body functions, thus define them NULL.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623094454.12427-1-vaibhavgupta40@gmail.com
In case of an error, no one will use the allocated structure. Call
ieee80211_free_hw, same as in rtl_usb_disconnect.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-4-code@reto-schneider.ch
Prevent code from calling itself indirectly, causing the driver to hang
and consume 100% CPU.
Without this fix, the following script can bring down a single CPU
system:
```
while true; do
rmmod rtl8192cu
modprobe rtl8192cu
done
```
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-2-code@reto-schneider.ch
Sparse reports the following issue:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: warning: incorrect type in initializer (different base types)
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: expected restricted __le32 [usertype] *pdesc
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: got unsigned int [usertype] *
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604005733.7905-3-Larry.Finger@lwfinger.net
In some b43 files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-6-f.suligoi@asem.it
In at76c50x-usb.c the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-5-f.suligoi@asem.it
The wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-3-f.suligoi@asem.it
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
The length of the key comes from the network and it's a 16 bit number. It
needs to be capped to prevent a buffer overflow.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200708115857.GA13729@mwanda
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and we only need
the spinlock to see if we need to queue tx work or not. And wlcore_irq()
holds the mutex.
To simplify the locking, we can use spin_trylock and always queue tx
work unless we know there's nothing to do.
Let's also update the comment a bit while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-4-tony@atomide.com
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and
wlcore_irq() already holds the mutex calling wlcore_irq_locked().
And we only need the spinlock to see if we need to run the queue
or not.
To simplify the locking, we can use spin_trylock and always run the
tx queue unless we know there's nothing to do.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-3-tony@atomide.com
We can simplify the runtime resume ELP path by always setting and
clearing the completion in runtime resume. This way we can test for
WL1271_FLAG_IRQ_RUNNING after the resume write to see if we need
completion at all.
And in wlcore_irq(), we need to take spinlock for running the
completion and for the pm_wakeup_event(). Spinlock is not needed
around the bitops flags check for WL1271_FLAG_SUSPENDED so the
spinlocked sections get shorter.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-2-tony@atomide.com
This macro is already used in mwifiex driver for specifying upper limit and
is defined to value 3. So use it also in struct ieee80211_iface_limit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200626152938.12737-1-pali@kernel.org
New device ID 0xc82f found on Lenovo ThinkCenter.
Tested it with c822 driver, works good.
PCI id:
03:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd.
Device [10ec:c82f]
Subsystem: Lenovo Device [17aa:c02f]
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200612082745.204400-1-aaron.ma@canonical.com
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e37 ("rtw88: allows to enable/disable HCI link PS mechanism")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com
Since single rf path chips don't support TX SPBC, tell mac80211
to not advertise it.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
In order to get a better TX EVM, do calibration after association.
The calibration needed for 8821c is the IQK, which is done in the
firmware. Implement the rtw_chip_ops::phy_calibration() to trigger
firmware to calibrate.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-8-yhchuang@realtek.com
False alarm statistics can be used to adjust the RX gain. This
helps the driver to adapt to different circumstances.
Implement rtw_chip_ops::false_alarm_statistics() for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-7-yhchuang@realtek.com
Some RX packets contain also information about environment status.
Implement rtw_chip_ops::query_rx_desc() for 8821c. Parse the RX
descriptor which describes the current condition of the received
packet.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-6-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial
gain depends on field situation.
Define the register addresses for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-4-yhchuang@realtek.com
To configure the transmit power of 8821c implement trasmit
power index setting callback function for 8821c. This is very
similar to the callback function of 8822b.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-3-yhchuang@realtek.com
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips.
This patch adds the basic functions such as parameter tables, chip
information, power on flow.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type defining 'NETDEV_TX_OK' but this
driver returns '0' instead of 'NETDEV_TX_OK'.
Fix this by returning 'NETDEV_TX_OK' instead of '0'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629104009.84077-1-luc.vanoostenryck@gmail.com
Added version number info along with firmware name so driver can pick
the correct revision of FW file. Moved FW filename macro as part of
driver code & added MODULE_FIRMWARE to specify FW needed by module.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-6-ajay.kathat@microchip.com
Modify WILC1000 binary filename to use single unified wilc1000 FW.
A single wilc1000 binary is used for different wilc1000 revisions.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-5-ajay.kathat@microchip.com
Avoid below reported warning found when 'CONFIG_PM' config is
undefined.
'warning: unused variable 'wowlan_support' [-Wunused-const-variable]'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-4-ajay.kathat@microchip.com
Make use 'strlcpy' instead of 'strncpy' to overcome 'stringop-truncation'
compiler warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-3-ajay.kathat@microchip.com
The code in the BRCM80211 BRCMSMAC driver is using the legacy
GPIO API to to a complex check of the validity of the base of
the GPIO chip and whether it is present at all and then adding
an offset to the base of the chip.
Use the existing function to obtain a GPIO line internally
from a GPIO chip so we can use the offset directly and
modernize the code to use GPIO descriptors instead of integers
from the global GPIO numberspace.
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Frank Kao <frank.kao@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200711210150.4943-1-linus.walleij@linaro.org
The driver relies on the compatible string from DT to determine which
FW configuration file it should load. The DTS spec allows for '/' as
part of the compatible string. We change this to '-' so that we will
still be able to load the config file, even when the compatible has a
'/'. This fixes explicitly the firmware loading for
"solidrun,cubox-i/q".
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans deGoede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701112201.6449-1-matthias.bgg@kernel.org
Linux 3.6 introduces TSQ which has a per socket threshold for TCP Tx
packet to reduce latency. In flow control mode, host driver enqueues skb
in hanger and TCP doesn't push new skb frees until host frees the skb when
receiving fwstatus event. So set pacing shift 8 to send them as a single
large aggregate frame to the bus layer.
43455 TX TCP throughput in different FC modes on Linux 5.4.18
sk_pacing_shift : Throughput (fcmode=0)
10: 245 Mbps
9: 245 Mbps
8: 246 Mbps
7: 246 Mbps
sk_pacing_shift : Throughput (fcmode=1)
10: 182 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
sk_pacing_shift : Throughput (fcmode=2)
10: 180 Mbps
9: 197 Mbps
8: 206 Mbps
7: 207 Mbps
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-3-wright.feng@cypress.com
When USB or SDIO device got abnormal bus disconnection, host driver
tried to clean up the skbs in PSQ and TXQ (The skb's pointer in hanger
slot linked to PSQ and TSQ), so we should set the state of skb hanger slot
to BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb.
In brcmf_fws_bus_txq_cleanup it already sets
BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb, therefore we add the
same thing in brcmf_fws_psq_flush to avoid following warning message.
[ 1580.012880] ------------ [ cut here ]------------
[ 1580.017550] WARNING: CPU: 3 PID: 3065 at
drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49
brcmu_pkt_buf_free_skb+0x21/0x30 [brcmutil]
[ 1580.184017] Call Trace:
[ 1580.186514] brcmf_fws_cleanup+0x14e/0x190 [brcmfmac]
[ 1580.191594] brcmf_fws_del_interface+0x70/0x90 [brcmfmac]
[ 1580.197029] brcmf_proto_bcdc_del_if+0xe/0x10 [brcmfmac]
[ 1580.202418] brcmf_remove_interface+0x69/0x190 [brcmfmac]
[ 1580.207888] brcmf_detach+0x90/0xe0 [brcmfmac]
[ 1580.212385] brcmf_usb_disconnect+0x76/0xb0 [brcmfmac]
[ 1580.217557] usb_unbind_interface+0x72/0x260
[ 1580.221857] device_release_driver_internal+0x141/0x200
[ 1580.227152] device_release_driver+0x12/0x20
[ 1580.231460] bus_remove_device+0xfd/0x170
[ 1580.235504] device_del+0x1d9/0x300
[ 1580.239041] usb_disable_device+0x9e/0x270
[ 1580.243160] usb_disconnect+0x94/0x270
[ 1580.246980] hub_event+0x76d/0x13b0
[ 1580.250499] process_one_work+0x144/0x360
[ 1580.254564] worker_thread+0x4d/0x3c0
[ 1580.258247] kthread+0x109/0x140
[ 1580.261515] ? rescuer_thread+0x340/0x340
[ 1580.265543] ? kthread_park+0x60/0x60
[ 1580.269237] ? SyS_exit_group+0x14/0x20
[ 1580.273118] ret_from_fork+0x25/0x30
[ 1580.300446] ------------ [ cut here ]------------
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624091608.25154-2-wright.feng@cypress.com
commit 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
adds a reset function to recover firmware trap for PCIe bus. This commit
adds an implementation for SDIO bus.
Upon SDIO firmware trap, do below:
- Remove the device
- Reset hardware
- Probe the device again
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
Ignore FW event if the event's BSSID is different form the BSSID of the
currently connected AP. Check interface state is connected or not, if
state is not connected that can ignore link down event.
Signed-off-by: Able Liao <Able.Liao@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-4-chi-hsien.lin@cypress.com
Current brcmf_link_down() always call cfg80211_disconnected() with
locally_generated=1, which is not always the case. Add event source
argument on link down handler and set locally_generated based on the
real trigger.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-3-chi-hsien.lin@cypress.com
Unable to change back to visiable SSID because there is
no disable hidden ssid routine.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200618160739.21457-2-chi-hsien.lin@cypress.com
Commit 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg
method") did not initialize requested_dwell properly, resulting in an
always-false dwell time overflow check. Fix it by setting the correct
requested_dwell value.
Fixes: 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-7-chi-hsien.lin@cypress.com
This patch move the credit map setting to right place to avoid
brcmf_fws_return_credits() return without setting the credit map.
It fix the thoughput zero stalls issue in softAP mode when STA
using PM 1 mode.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
There is a mismatch of tx status flag values between host and firmware.
It makes the host mistake the flags and have incorrect behavior of credit
returns. So update the flags to sync with the firmware ones.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192.
Increase the message buffer max size same as wifi firmware for control
packets so return buffers can come back.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
Current credit borrowing allows only the access category BE to
borrow the credits. This change is to fix the credit borrowing
logic, to make borrowing available for all access categories
and also to borrow only from the lower categories. This fixes WFA
802.11n certs 5.2.27 failures.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
Bss info flag definition need to be fixed from 0x2 to 0x4
This flag is for rssi info received on channel.
All Firmware branches defined as 0x4 and this is bug in brcmfmac.
Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
The firmware state machines are not fully suitable for concurrent
station interface support, it may hit unexpected error if we have 2
different SSIDs and the roaming scenarios concurrently.
To avoid the bad user-experience if this is not fully validated, we
dis-allow user to create two concurrent station interfaces.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no
pending event or data. As a result, host driver does not poll firmware
console buffer before buffer overflow, which leads to missing firmware
logs. We should not stop SDIO watchdog if console_interval is non-zero
in debug build.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
When host driver retrieves mac addresses from dongle, driver copies memory
from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero
array which causes permanent MAC address in wiphy is all zero as well.
To fix this, we set drvr->mac before setting perm_addr.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
To truncate the additional bytes, if extra bytes have been received.
Current code only have a warning and proceed without handling it.
But in one of the crash reported by DVT, these causes the
crash intermittently. So the processing is limit to the skb->len.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfDJcKAAoJEG4XJFUm622boM4H+wTnBdnamYPASeJ8la5D5hyk
pXcPFYwTVjC48Cs+XWpcib2AQxrgZV8fF9SdbZqqCleZGGXSXsQb6WiaSr7JxFso
gbSaUHhYpfSOXdadNBI0ho/E+NFEsnIcIxMS2BJQTe9AUXCFY3oX56ut0ioSKx4P
rkgqTe0pvYUvLR4EOwCCWUndfrAgARy2KXqNsTmCCb5tXJf2leAjGyVRteX9RJQq
GSooKPrOJRLAiyId17D7kLPc8WHVv1KxBbRUgyC046s67CzDSEBw1jOy6Q2oncvI
ZCow/i7AuZSeSw3t6HRuy4ArMuRCafk1gKEbKw6TTVg47iGHn7JqrCs+l5do7hE=
=10X3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
First set of fixes for v5.8. Various important fixes for iwlwifi and
mt76.
iwlwifi
* fix sleeping under RCU
* fix a kernel crash when using compressed firmware images
mt76
* tx queueing fixes for mt7615/22/63
* locking fix
* fix a crash during watchdog reset
* fix memory leaks
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an immutable branch shared between wireless-drivers-next and
staging-next for moving wilc1000 driver out of staging to drivers/net/wireless
directory.
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Organize driver documentation by device type. Most documents
have fairly verbose yet uninformative names, so let users
first select a well defined device type, and then search for
a particular driver.
While at it rename the section from Vendor drivers to
Hardware drivers. This seems more accurate, besides people
sometimes refer to out-of-tree drivers as vendor drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid adding MT7615_EEPROM_SIZE twice.
Rename MT7615_EEPROM_EXTRA_DATA to MT7615_EEPROM_FULL_SIZE, since it already
includes MT7615_EEPROM_SIZE
Fixes: ad380ad1eb ("mt76: mt7615: add support for applying DC offset calibration from EEPROM")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622150716.49622-1-nbd@nbd.name
Fix the two following memory leaks in mt7663u_probe:
1- if device power-own times out, remove ieee80211 hw device.
2- if mt76u queues allocation fails, remove pending urbs.
Fixes: eb99cc95c3 ("mt76: mt7615: introduce mt7663u support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e4098f0c8a9ac51997de07f38c2bcdf7042d6db1.1592755166.git.lorenzo@kernel.org
Fixes a crash on MMIO devices when running into the watchdog reset
Fixes: d3377b78ce ("mt76: add HE phy modes and hardware queue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200615181341.81871-1-nbd@nbd.name
* tx queueing fixes for mt7615/22/63
* locking fix
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl7dBRsACgkQ130UHQKnbvUpiQCgjHAeT1fOKnFfFF5kHzECEyFS
1N8An0endTyFWAXCZd3aEgK4/nQN4LwR
=6f32
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-06-07' of https://github.com/nbd168/wireless
mt76 patches for 5.8
* tx queueing fixes for mt7615/22/63
* locking fix
# gpg: Signature made Sun 07 Jun 2020 06:17:47 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org
To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.
Also remove a useless info print, it's more like a debug message anyway.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org
pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping
pdev_id ipq8074 ipq6018
------- ------- -------
0 0 0
1 2 1
2 1 Not applicable
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org
Convert to ath11k_hw_params to an array to make it possible add new hardware in
the future, for example IPQ6018 or QCA6390.
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-3-git-send-email-kvalo@codeaurora.org
A compromized ath10k peripheral is able to control the size argument
of memcpy in ath10k_pci_hif_exchange_bmi_msg.
The min result from previous line is not used as the size argument
for memcpy. Instead, xfer.resp_len comes from untrusted stream dma
input. The value comes from "nbytes" in ath10k_pci_bmi_recv_data,
which is set inside _ath10k_ce_completed_recv_next_nolock with the line
nbytes = __le16_to_cpu(sdesc.nbytes);
sdesc is a stream dma region which device can write to.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616132544.17478-1-bruceshenzk@gmail.com
We need this so that all hardware versions can coexist and
it's easier to manage everything then all hardware
directories are under ath11k directory.
Copy ath11k firmware files to
/lib/firmware/ath11k/IPQ8074/hw2.0/
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591709581-18039-3-git-send-email-akolli@codeaurora.org
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
Tested-on: QCA9984 PCI 10.4-3.6-00104
Tested-on: QCA9882 PCI 10.2.4-1.0-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591856446-26977-1-git-send-email-vnaralas@codeaurora.org
On wcn3990 we have "per_ce_irq = true". That makes the
ath10k_ce_interrupt_summary() function always return 0xfff. The
ath10k_ce_per_engine_service_any() function will see this and think
that _all_ copy engines have an interrupt. Without checking, the
ath10k_ce_per_engine_service() assumes that if it's called that the
"copy complete" (cc) interrupt fired. This combination seems bad.
Let's add a check to make sure that the "copy complete" interrupt
actually fired in ath10k_ce_per_engine_service().
This might fix a hard-to-reproduce failure where it appears that the
copy complete handlers run before the copy is really complete.
Specifically a symptom was that we were seeing this on a Qualcomm
sc7180 board:
arm-smmu 15000000.iommu: Unhandled context fault:
fsr=0x402, iova=0x7fdd45780, fsynr=0x30003, cbfrsynra=0xc1, cb=10
Even on platforms that don't have wcn3990 this still seems like it
would be a sane thing to do. Specifically the current IRQ handler
comments indicate that there might be other misc interrupt sources
firing that need to be cleared. If one of those sources was the one
that caused the IRQ handler to be called it would also be important to
double-check that the interrupt we cared about actually fired.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200609082015.1.Ife398994e5a0a6830e4d4a16306ef36e0144e7ba@changeid
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
-----BEGIN PGP SIGNATURE-----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=MRiL
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.9
* Fix links to wiki;
* Some preparations for gcc-10;
* Make FW reconfiguration quieter by not using warn level;
* Some other small fixes and clean-up;
# gpg: Signature made Thu 11 Jun 2020 12:03:51 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
With addition of 6Ghz channels, it is possible that wmi buffer size can
exceed the maximum wmi buffer size. So iterate over the channel list,
and send multiple messages till channel list is empty.
Also mark PSC channel flag for 6GHz channels accordingly.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-8-pradeepc@codeaurora.org
If 6 ghz channel is a Preferred Scanning Channel(PSC), mark
the channel flag accordingly when updating channel list to firmware.
This will be used when making scanning decision in 6GHz channels.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-6-pradeepc@codeaurora.org
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
As 6GHz cahnnel numbers overlap with those of 5GHz and 2GHz bands,
it is necessary to use frequency when determining the band info
in rx path.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-4-pradeepc@codeaurora.org
In some Intel files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200605154112.16277-7-f.suligoi@asem.it
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185538.GA14674@embeddedor
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-10 complains when a zero-length array is accessed:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c: In function 'iwl_mvm_rx_ba_notif':
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1929:17: warning: array subscript 9 is outside the bounds of an interior zero-length array 'struct iwl_mvm_compressed_ba_tfd[0]' [-Wzero-length-bounds]
1929 | &ba_res->tfd[i];
| ~~~~~~~~~~~^~~
In file included from drivers/net/wireless/intel/iwlwifi/mvm/../fw/api/tdls.h:68,
from drivers/net/wireless/intel/iwlwifi/mvm/fw-api.h:68,
from drivers/net/wireless/intel/iwlwifi/mvm/sta.h:73,
from drivers/net/wireless/intel/iwlwifi/mvm/mvm.h:83,
from drivers/net/wireless/intel/iwlwifi/mvm/tx.c:72:
drivers/net/wireless/intel/iwlwifi/mvm/../fw/api/tx.h:769:35: note: while referencing 'tfd'
769 | struct iwl_mvm_compressed_ba_tfd tfd[0];
| ^~~
Change this structure to use a flexible-array member for 'tfd' instead,
along with the various structures using an zero-length ieee80211_hdr
array that do not show warnings today but might be affected by similar
issues in the future.
Fixes: 6f68cc367a ("iwlwifi: api: annotate compressed BA notif array sizes")
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200430213101.135134-3-arnd@arndb.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some ath files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-4-f.suligoi@asem.it
ath10k_htt_tx_free_msdu_id() has a lockdep assertion that htt->tx_lock
is held. Acquire the lock in a couple of error paths when calling that
function to ensure this condition is met.
Fixes: 6421969f24 ("ath10k: refactor tx pending management")
Fixes: e62ee5c381 ("ath10k: Add support for htt_data_tx_desc_64 descriptor")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604105901.1.I5b8b0c7ee0d3e51a73248975a9da61401b8f3900@changeid
The variable ret is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200420222449.99481-1-colin.king@canonical.com
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The correct variable name was replaced here by mistake by commit
ab27926d9e ("iwlwifi: fix devices with PCI Device ID 0x34F0 and 11ac RF
modules").
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20200210135817.31994-1-luca@lucaceresoli.net
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On AX200, the average power was showing positive instead of negative, but
otherwise matched the expected RSSI. Flip the value to negative before
giving to mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191126214744.1283-1-greearb@candelatech.com
[removed unnecessary check and some unnecessary parentheses]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL_WARN seems excessive here since this can happen during normal
operation. Every time I connect to a new network with 8086:24fd I get
this as KERN_WARNING on the console, which mildly distracts from other
more pressing messages. For example:
% sudo journalctl _TRANSPORT=kernel | grep -c 'FW already configured'
403
Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: https://lore.kernel.org/r/20191017144841.GA16393@chrisdown.name
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Overwrite hw queue id for non-bufferable management frames if the hw
support always txq (altxq) in order to be in sync with mac txwi code
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7622/mt7663 chipsets rely on a fixed reverse queue map order respect
to mac80211 one:
- q(0): IEEE80211_AC_BK
- q(1): IEEE80211_AC_BE
- q(2): IEEE80211_AC_VI
- q(3): IEEE80211_AC_VO
Fixes: cdad487405 ("mt76: mt7615: add dma and tx queue initialization for MT7622")
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
acs and wmm index are swapped in mt7615_queues_acq respect to the hw
design
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Coverage class callback can potentially run in parallel with other
routines (e.g. mt7615_set_channel) that configures timing registers.
Run coverage class callback holding mt76 mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All iwlwifi cards below the 22000 series are able to handle multiple
keyids per STA and allow the selection of the encryption key per MPDU.
These are therefore fully compatible with the Extended Key ID support
implementation in mac80211.
Enable Extended Key ID support for all dvm cards and the mvm cards not
using the incompatible new Tx API introduced for the 22000 series.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190819180540.2855-1-alexander@wetzel-home.de
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Firmware for sd8997 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8997_combo_v4.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8997.
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8977 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8977_combo_v2.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8977.
Fixes: 1a0f547831 ("mwifiex: add support for sd8977 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
-----BEGIN PGP SIGNATURE-----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=wdaG
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of changes, including
* many 6 GHz changes, though it's not _quite_ complete
(I left out scanning for now, we're still discussing)
* allow userspace SA-query processing for operating channel
validation
* TX status for control port TX, for AP-side operation
* more per-STA/TID control options
* move to kHz for channels, for future S1G operation
* various other small changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ath10k/qmi.h header file contains a declaration for the function
ath10k_qmi_register_service_notifier(). This function doesn't exist.
Remove the declaration.
This patch is a no-op and was just found by code inspection.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=nlI2
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third set of iwlwifi patches intended for v5.8
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 29 May 2020 10:38:28 AM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to
inform kernel about maximum number of p2p connections and stations in AP
mode.
During initialization of SD8997 wifi chip kernel prints warning:
mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217
This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets
appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure.
It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123559.29028-1-pali@kernel.org
During initialization of SD8997 wifi chip kernel prints warnings:
mwifiex_sdio mmc0:0001:1: Unknown api_id: 3
mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
This patch adds support for parsing all api ids provided by SD8997
firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123444.28957-1-pali@kernel.org
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.
The fix is to pad skb->data to at least ETH_ZLEN bytes.
Cc: <stable@vger.kernel.org>
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
When wlcore_fw_status() returns an error code, a pairing
runtime PM usage counter decrement is needed to keep the
counter balanced. It's the same for all error paths after
wlcore_fw_status().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522044906.29564-1-dinghao.liu@zju.edu.cn
The CCK TX setting when switch channel will fix the CCK to
path A only, so if the antenna is configured to path B
(e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK
packets can never be delivered to the air if only path B is
connected with an antenna (it can possibly be transmitted
through path A, but as path B is configured, the expected
behavior is incorrect).
This can also solve the racing issue of CCK TX setting between
driver and firmware. The CCK TX setting in driver should be
removed. Otherwise, the CCK TX setting would be wrong when the
racing occurs.
Fixes: 297bcf8222 ("rtw88: add support for set/get antennas")
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522091234.24495-1-yhchuang@realtek.com
For older versions of gcc, the array = {0}; will cause warnings:
drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim':
>> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning:
>> missing braces around initializer [-Wmissing-braces]
s8 bb_gain[2][8] = {0};
^
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near
initialization for 'bb_gain[0]') [-Wmissing-braces]
Fixes: 5ad4d8957b ("rtw88: set power trim according to efuse PG values")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Coex mechanism used to make BT have higher priority and more time to
transfer data when BT inquiry-page, which leads to poor WiFi performance.
Should take WiFi traffic into consideration. If the WiFi is having heavy
traffic, use another parameter to make sure WiFi has more chance to TX/RX,
while guarantee the priority of BT for inquiry. If the WiFi isn't busy
(connected or not), set proper parameter to fix originals.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-3-yhchuang@realtek.com
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
When wl12xx_cmd_role_disable() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520130806.14789-1-dinghao.liu@zju.edu.cn
When wlcore_hw_interrupt_notify() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520125724.12832-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124649.10848-1-dinghao.liu@zju.edu.cn
There are two error handling paths in this functon. When
wlcore_tx_work_locked() returns an error code, we should
decrease the runtime PM usage counter the same way as the
error handling path beginning from pm_runtime_get_sync().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124241.9931-1-dinghao.liu@zju.edu.cn
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200525134906.1672-1-rsalvaterra@gmail.com
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Check for "AR6003 or later" is slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath6kl.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-8-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Range request version 10 keeps the same command size as version 9
but uses 2 reserved fields for the responder beacon interval and
station id (if exists).
For now, since the beacon interval of unassoc APs is unknown, use
a value of 100 TUs which is a common value for many APs.
While at it, remove the definition for CCMP_256 cipher, since this
is not supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.b7ccdad0805f.I59ea7f773caed85a66c61401066ae169008442e6@changeid
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
Newer firmware versions will parse a few extra bits in the
context info to be able to determine whether we are using
bigger than 4k RBs, indicate 8k/12k to them if we actually
use those (e.g. for sniffer based on the module parameter).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.f83f994572ca.Ibcfd66c3f9b69e68a53b3b2df8331ffb225db655@changeid
ACPI Device Specific Method (DSM) allows standardized feature
configuration through the ACPI interface without the namespace
pollution of the usual mechanism (ACPI method for each feature).
Add generic function for evaluating DSM objects and function for
evaluating a DSM with no arguments and a single int return value.
also implement the required backport for UUID.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.c3242ff3ba5c.Icb48c8d61bede5dda7ef267bff10e4798e9dc77b@changeid
MT7611N is basically the same as MT7615N, except it only supports 5GHz
It is used by some TP-Link and Mercury wireless routers
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a NULL pointer dereference in mt7915_register_ext_phy since phy
data structure is allocated by mt76_alloc_phy routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are some spelling mistakes in some literal strings. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drivers/net/wireless/mediatek/mt76/mt7915/main.c:694:1: sparse:
sparse: context imbalance in 'mt7915_sta_rc_update' - wrong count at exit
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:303:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:304:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:305:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:319:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:327:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:345:41: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:355:33: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: sparse: invalid assignment: |=
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: left side has type unsigned int
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: right side has type restricted __le32
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move assignment of .data1 and .data2 to a single place and fix overwriting
of values from the template
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable or disable OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
With this patch, we can get ~20% gain in OBSS OTA environment.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x02_mcu_msg_send is run just by mmio code so get rid of
mt76_is_mmio() check
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJey69PAAoJEG4XJFUm622bIcEH/iT2M037SSfySAdykAvUQHJU
E1E9iZKJVVKZ+8nfTh03thtT4HyPC0jZMjWrqL5N4PFTKJKJo/t9HfAEq4niboGj
l2jeqQpujck7zUBKQh4HWWJiDtpOiMUS9noHSujnS4NThtRo/+/qxIiCz6nxVBix
DHKi+zZR4t05U3UYYivWc/CfojIXLrqeZl187MnDBV6LvNP8/en+HpmnCzp/trFn
qxBl2MWzr1oZf8j+t1UPtDVnUz1OMcHvnCQosQMeBwNtkkqKGc7Cip6VG/fqsLau
HdLwQWvsRByFT7yaXbwI+/uOMZhZ/KPWx9BdDdistegxyE8fZvjs/csfk7p3lSc=
=sKYR
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Second set of patches for v5.8. Lots of new features and new supported
hardware for mt76. Also rtw88 got new hardware support.
Major changes:
rtw88
* add support for Realtek 8723DE PCI adapter
* rename rtw88.ko/rtwpci.ko to rtw88_core.ko/rtw88_pci.ko
iwlwifi
* stop supporting swcrypto and bt_coex_active module parameters on
mvm devices
* enable A-AMSDU in low latency
mt76
* new devices for mt76x0/mt76x2
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from ./include/linux/firmware.h:6:0,
from drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:4:
In function ‘__mt7915_mcu_msg_send’,
inlined from ‘mt7915_mcu_send_message’ at drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:370:6:
./include/linux/compiler.h:396:38: error: call to ‘__compiletime_assert_545’ declared with attribute error: BUILD_BUG_ON failed: cmd == MCU_EXT_CMD_EFUSE_ACCESS && mcu_txd->set_query != MCU_Q_QUERY
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
./include/linux/compiler.h:377:4: note: in definition of macro ‘__compiletime_assert’
prefix ## suffix(); \
^~~~~~
./include/linux/compiler.h:396:2: note: in expansion of macro ‘_compiletime_assert’
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^~~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:39:37: note: in expansion of macro ‘compiletime_assert’
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^~~~~~~~~~~~~~~~~~
./include/linux/build_bug.h:50:2: note: in expansion of macro ‘BUILD_BUG_ON_MSG’
BUILD_BUG_ON_MSG(condition, "BUILD_BUG_ON failed: " #condition)
^~~~~~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:280:2: note: in expansion of macro ‘BUILD_BUG_ON’
BUILD_BUG_ON(cmd == MCU_EXT_CMD_EFUSE_ACCESS &&
^~~~~~~~~~~~
BUILD_BUG_ON is meaningless here, chang it to WARN_ON.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522034533.61716-1-yuehaibing@huawei.com
If 'thermal_cooling_device_register()' fails, we must undo what has been
allocated so far. So we must go to 'err_thermal_destroy' instead of
returning directly
In case of error in 'ath11k_thermal_register()', the previous
'thermal_cooling_device_register()' call must also be undone. Move the
'ar->thermal.cdev = cdev' a few lines above in order for this to be done
in 'ath11k_thermal_unregister()' which is called in the error handling
path.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513201454.258111-1-christophe.jaillet@wanadoo.fr
The for-loop seems to be redundant, the assignments for indexes
0..2 are being over-written by the last index 3 in the loop. Remove
the loop and use index 3 instead.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515102226.29819-1-colin.king@canonical.com
The mwifiex_cfg80211_dump_station() uses static variable for iterating
over a linked list of all associated stations (when the driver is in UAP
role). This has a race condition if .dump_station is called in parallel
for multiple interfaces. This corruption can be triggered by registering
multiple SSIDs and calling, in parallel for multiple interfaces
iw dev <iface> station dump
[16750.719775] Unable to handle kernel paging request at virtual address dead000000000110
...
[16750.899173] Call trace:
[16750.901696] mwifiex_cfg80211_dump_station+0x94/0x100 [mwifiex]
[16750.907824] nl80211_dump_station+0xbc/0x278 [cfg80211]
[16750.913160] netlink_dump+0xe8/0x320
[16750.916827] netlink_recvmsg+0x1b4/0x338
[16750.920861] ____sys_recvmsg+0x7c/0x2b0
[16750.924801] ___sys_recvmsg+0x70/0x98
[16750.928564] __sys_recvmsg+0x58/0xa0
[16750.932238] __arm64_sys_recvmsg+0x28/0x30
[16750.936453] el0_svc_common.constprop.3+0x90/0x158
[16750.941378] do_el0_svc+0x74/0x90
[16750.944784] el0_sync_handler+0x12c/0x1a8
[16750.948903] el0_sync+0x114/0x140
[16750.952312] Code: f9400003 f907f423 eb02007f 54fffd60 (b9401060)
[16750.958583] ---[ end trace c8ad181c2f4b8576 ]---
This patch drops the use of the static iterator, and instead every time
the function is called iterates to the idx-th position of the
linked-list.
It would be better to convert the code not to use linked list for
associated stations storage (since the chip has a limited number of
associated stations anyway - it could just be an array). Such a change
may be proposed in the future. In the meantime this patch can backported
into stable kernels in this simple form.
Fixes: 8baca1a34d ("mwifiex: dump station support in uap mode")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515075924.13841-1-pali@kernel.org
Currently ldo_pwr has the LDO25 voltage bits set to zero and then
it is overwritten with the new voltage setting. The assignment
looks incorrect, it should be bit-wise or'ing in the new voltage
setting rather than a direct assignment.
Addresses-Coverity: ("Unused value")
Fixes: 1afb5eb7a0 ("rtw88: 8723d: Add cfg_ldo25 to control LDO25")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200514181329.16292-1-colin.king@canonical.com
Rename the name of the kernel module for rtw88's core and pci.
Add proper prefix 'rtw88_' to easily recognize them, also can
avoid confusion with other drivers. (ex. r8822be in staging)
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-8-yhchuang@realtek.com
remove the unused about pci after extracting chip modules
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-7-yhchuang@realtek.com
Make objects about 8723d functions and 8723d tables,
i.e. rtw8723d.o and rtw8723d_table.o, an individual
kernel module called rtw88_8723d.ko.
For 8723d pcie chip, i.e. 8723DE chip, add a chip
entry point module called rtw88_8723de.ko which
will depend on rtw88_8723d.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-6-yhchuang@realtek.com
Make objects about 8822b functions and 8822b tables,
i.e. rtw8822b.o and rtw8822b_table.o, an individual
kernel module called rtw88_8822b.ko.
For 8822b pcie chip, i.e. 8822BE chip, add a chip
entry point module called rtw88_8822be.ko which
will depend on rtw88_8822b.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-5-yhchuang@realtek.com
Make objects about 8822c functions and 8822c tables,
i.e. rtw8822c.o and rtw8822c_table.o, an individual
kernel module called rtw88_8822c.ko.
For 8822c pcie chip, i.e. 8822CE chip, add a chip
entry point module called rtw88_8822ce.ko which
will depend on rtw88_8822c.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-4-yhchuang@realtek.com
In the current design, chip entry points are built into
the pci module. That makes the pci module depend on chips.
According to dependence, once the pci module is loaded,
kernel will load chip functionalities, including those that
may not be currently used.
We plan to split chip entry points from the pci module.
Thence we export pci symbols that will be used in chip
entry point modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-3-yhchuang@realtek.com
In the current design, various chip functions and tables
are built into rtw88 core. That causes kernel to load its
functionalities even if a chip isn't currently used. We
plan to make each chip's functionalities a separate
kernel module to reduce rtw88 core. And kernel will be
able to load the necessary.
Before extracting chip functionalities, we export symbols
inside rtw88 core which will be used in chip modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-2-yhchuang@realtek.com
Seven years ago we tried to fix a leak but actually introduced a double
free instead. It was an understandable mistake because the code was a
bit confusing and the free was done in the wrong place. The "skb"
pointer is freed in both _rtl_usb_tx_urb_setup() and _rtl_usb_transmit().
The free belongs _rtl_usb_transmit() instead of _rtl_usb_tx_urb_setup()
and I've cleaned the code up a bit to hopefully make it more clear.
Fixes: 36ef0b473f ("rtlwifi: usb: add missing freeing of skbuff")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513093951.GD347693@mwanda
* new devices for mt76x0/mt76x2
* mt7615 fixes
* mt7663 fixes
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
-----BEGIN PGP SIGNATURE-----
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAl69GP8ACgkQ130UHQKnbvUK1QCguAkkko7P79NpRiqd2MydjmWi
4dIAoIhmr8PEsh1fOsMBMqInupEnDKoZ
=biCw
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2020-05-14' of https://github.com/nbd168/wireless
mt76 patches for 5.8
* new devices for mt76x0/mt76x2
* mt7615 fixes
* mt7663 fixes
* support for non-offload firmware on mt7663
* hw/sched scan support for mt7663
* mt7615/mt7663 MSI support
* TDLS support
* mt7603/mt7615 rate control fixes
* new driver for mt7915
* wowlan support for mt7663
* suspend/resume support for mt7663
# gpg: Signature made Thu 14 May 2020 01:10:07 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
Fix typo defining ps_work in mt7615_register_ext_phy(). This is not a
real issue since 802.11 power save is not yet support by the external phy
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce essential bss information for multiple vifs hw_scan in
mt7615_mcu_uni_add_dev adding the interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce p2p-go/p2p-client suppor to mt76 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Differentiate hw scan channel time between passive and active scan
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_mcu_sched_scan_enable should be taken along with
mt7615_mcu_sched_scan_req to have proper scan plans initialization.
Fixes: bd39bd2f00c3 ("mt76: mt7663: introduce WoW with net detect support")
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* Support new FW APIs;
* Remove some old and unused features;
* HW configuration rework continues;
* Some queues rework by Johannes;
* Enable A-AMSDU in low latency;
* Some debugging fixes;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=LNbB
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches intended for v5.8
* Support new FW APIs;
* Remove some old and unused features;
* HW configuration rework continues;
* Some queues rework by Johannes;
* Enable A-AMSDU in low latency;
* Some debugging fixes;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 08 May 2020 10:08:58 AM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151758.GA4962@embeddedor
HTT EXT stats comes in stream of TLVs spanning over multiple
messages. Currently completion is being sent for each message
which is creating a race where stats_req is being accessed
for filling in second message after the memory is already
freed in release operation. Fix this by issuing completion
once all the messages are received and processed. Driver
knows this info from DONE bit set in htt msg.
Also fix locking required for htt stats.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589221074-28778-1-git-send-email-pradeepc@codeaurora.org
Fix the following warning:
drivers/net/wireless/realtek/rtl818x/rtl8187/rtl8225.c:609:17: warning:
‘rtl8225z2_tx_power_ofdm’ defined but not used
static const u8 rtl8225z2_tx_power_ofdm[] = {
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513011754.28432-1-chentao107@huawei.com
sparse warnings: (new ones prefixed by >>)
>> drivers/net/wireless/realtek/rtw88/rtw8723d.c:1899:6: sparse: sparse:
symbol 'rtw8723d_pwr_track' was not declared. Should it be static?
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512103534.5889-1-yhchuang@realtek.com
8723D adds some experimental features to word 0x06 of cam entry, so fill
zeros to initialize them to off state. For existing chips, these two words
are reserved and always zeros, so this change is harmless for them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-9-yhchuang@realtek.com
8723D is a Wifi+BT combo card. To make them work properly, we need coex
mechanism to avoid interference, such as TX simultaneously. Basically,
coex.c provide main algorithm to deal with many use cases, and this commit
adds some parameters and ops differ from other chips, because coex
hardware and WiFi generation are changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-8-yhchuang@realtek.com
Since 8723D use different address of ltecoex register, this commit add a
new field in chip_info and fill proper address. Then, ltecoex_read_reg()
and ltecoex_reg_write() can use them to access ltecoex according to chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-7-yhchuang@realtek.com
Flush queue is used to check if queue is empty, before doing something
else. Since 8723D uses different registers and page number of
availabl/reserved occupy 8 bits instead of 16 bits, so use a 'wsize' field
to discriminate which rtw_read{8,16} is adopted.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-6-yhchuang@realtek.com
Without this patch, wifi card can't initialize properly due to BT in USB
suspend state. So, we disable BT USB suspend (wakeup) in shutdown callback
that is the moment before rebooting. To save BT USB power, we can't do this
in 'remove' callback.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-5-yhchuang@realtek.com
When chip's temperature is changed, RF characters are changed. To keep the
characters to be consistent, 8723d uses thermal meter to assist in
calibrating LCK, IQK, crystal and TX power.
A base thermal value is programmed in efuse, all calibration data in
MP process is based on this thermal value. So we calucate the delta of
thermal value between the base value, and use this delta to reference XTAL
and TX power offset tables to know how much we need to adjust.
For IQK and LCK, driver checks if delta of thermal value is over 8, then
they are triggered.
For crystal adjustment, when delta of thermal value is changed, we check
XTAL tables to get offset of XTAL value. If thermal value is larger than
base value, positive table (_p as suffix) is used. Otherwise, we use
negative table (_n as suffix). Then, we add offset to XTAL default value
programmed in efuse, and write sum value to register.
To compensate TX power, there are two hierarchical tables. First level use
delta of thermal value to access eight tables to yield delta of TX power
index. Then, plus base TX power index to get index of BB swing table
(second level tables) where register value is induced.
BB swing table can't deal with all cases, if index of BB swing table is
over the size of the table. In this case, TX AGC is used to compensate the
remnant part. Assume 'upper' is the upper bound of BB swing table, and
'target' is the desired index. Then, we can illustrate them as
compensation method BB swing TX AGC
------------------- -------- --------------
target > upper upper target - upper
target < 0 0 target
otherwise target 0
For debug purpose, add a column 'rem' to tx_pwr_tbl entry, and it looks
like
path rate pwr base (byr lmt ) rem
A CCK_1M 32(0x20) 34 -2 ( 0 -2) 0
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-4-yhchuang@realtek.com
IQ calibration is used to calibrate RF characteristic to yield expected
performance. Basically, we do calibration twice and compare the similarity
to determine calibration is good or not, if not we do the third
calibration, and then compare with the results of first and second
calibration. If it still not similar, IQK is failed.
Before doing calibration, we need to backup registers that will be
modified in calibration procedure, and restore these registers after
calibration is done.
A calibration procedure can divided into four sub-procedures that are
S1-TX, S1-RX, S0-TX and S0-RX. Where, S1 and S0 represent to path A and B
respectively. Each sub-procedure configure proper registers, and then
rigger one-shot calibration and poll until completion. For RX calibration,
it needs to do twice one-shot calibration, first one is to yield parameter
used by second one.
The result of TX part is stored for TX power tracking that adjusts TX AGC
to output expected power.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-3-yhchuang@realtek.com
LC calibration is done by hardware circuit. Driver sets the LCK bit to kick
start, and then poll the bit to check if it's done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-2-yhchuang@realtek.com
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
make mac_work per phy instead of per device and fix a possible deadlock
in mt7915_stop since mt7915_mac_work runs holding mt76 mutex
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add debug counters to track status of beamformer and beamformee.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows to set HE TxBF runtime stream capabilities
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable TxBF modules and trigger sounding process to support Tx beamformer.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a helper to reduce duplicate codes.
This is a preliminary patch to add Tx beamforming support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cancel possible power_save work before stopping the mt7663u interface
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing PLE/PSE base register definitions for mt7663u
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Copy key pointer value before running mt76_tx_status_skb_add() in
mt7663u_mac_write_txwi since it will be overwritten setting
mt76_tx_cb for probing frames
Co-developed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows host driver to get useful information of some important modules.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is useful for IBSS Mesh to adjust t_clockdrift.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reported-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver can manually set fixed rate for each peer through debugfs.
May use .set_bitrate_mask callback and iterate stations under the
current vif to achieve the aim once it supports HE rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add useful debug counters since this generation uses struct rate_info
to report HE tx rate.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This generation supports much more per-peer statistics than legacy ones,
so add .sta_add_debugfs accordingly.
This is convenient to set/get more settings/counters in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 expects the definition of what HE rate info is available
inside astruct prepended to the skb.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add basic HE BSS's info for interfaces. As for the advanced features
will be added gradually in the future patches.
(i.e. BSS color, TWT, spatial reuse and OFDMA)
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Shayne Chen <shayne.chen@mediatek.com>
Tested-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The capabilities for the HE interfaces are generated from the capabilities
reported by the firmware.
This should move to common file once we got other HE devices support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use firmware support for applying per-rate limit and power offsets.
This can support all HE RU types.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE rate reporting in Rx path
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for the MediaTek latest generation IEEE 802.11ax 4x4
device MT7915E, which supports concurrent dual-band operation at
both 5GHz and 2.4GHz.
Note that this patch just add basic part and will add more HE
capabilities support in the further patches.
The driver supports AP, Station, Mesh and monitor mode.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Suggested-by: Shihwei Lin <shihwei.lin@mediatek.com>
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Acked-by: Yiwei Chung <yiwei.chung@mediatek.com>
Acked-by: YF Luo <yf.luo@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The newer 802.11ax devices (i.e. MT7915E) can connect to much more
peers than previous generations.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enlarge slot to support 11ax 256 BA (256 MPDUs in an AMPDU)
Signed-off-by: Chih-Min Chen <chih-min.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure the mcu to scan all available channels if mac80211 does not
provide any frequency list
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support to sched scan with randomise addr
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce WoW with net detect support
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix mt7663 eeprom definitions for delta tx power parsing
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7615_eeprom_get_power_index can return negative error value.
Check mt7615_eeprom_get_power_index return value before using it
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If device has enabled beacon hw filter rx beacons are not reported to
the host. Introduce beacon_loss mcu event to trigger mac80211 mlme
connection state machine in this configuration.
IEEE80211_VIF_BEACON_FILTER has not set in vif flags since hw beacon
filter is not enabled yet
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add KCK and KEK offload support to mt7615 driver in order to
support GTK rekeying during PM suspend
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Signed-off-by: Wan-Feng Jiang <Wan-Feng.Jiang@mediatek.com>
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Soul Huang <Soul.Huang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested on Chromebok by "echo mem to /sys/power/state" to suspend and
then waked up by keyboard keystrokes to resume system.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce the mt7615_mcu_set_hif_suspend mcu command, which is usually
used to configure the interface including PCIe, USB or SDIO to the right
state during operation suspend / resume.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for hw beacon filter if available in the firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for passive frequency scanning to mt7615_mcu_hw_scan
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For the moment offload firmware supports just one entry in the scheduled
scan plan and so it runs till it is disabled by the userspace.
Do not mark the hw scheduled scan as disabled in mt7615_scan_work
after receiving a scan result
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_check_offload_capability routine to set hw/wiphy
offload capabilities according to the running firmware
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix SSID configuration performing hw frequency scanning
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
it will print an error message by itself when
devm_platform_ioremap_resource() goes wrong. so remove the duplicate
error message.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On top of the EEPROM target power, each rate can also has a power offset.
On many devices, this power offset is used to boost the tx power of lower
rates. Take this into account when parsing rate power.
The assumption here is, that the first rate (OFDM 6M or CCK 1M) has the
highest tx power
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of useless check in mt7663_load_n9 since it is used only for
mt7663 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7663 firmware v2 is used for embedded devices since it has more completed
features in AP mode.
Add the capability to specify which firmware load first (v3 or v2)
using prefer_offload_fw kernel parameter and fallback to the other one
if the selected firmware fails to load
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently mt7663 devices do not support DBDC so fw events have no info
about it. Fix mt7615_mcu_bss_event that wrongly use bss_idx as DBDC
band_idx while it is vif index.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce sta pointer to mt7615_mcu_add_bss_info signature in order to
avoid sta lookup in mt7615_mcu_bss_basic_tlv routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BMC entry for MT7663 unicmd firmware should be a broadcast/multicast entry,
not a unicast entry, that is GTK rekey offload would rely on.
Fixes: 138860679b ("mt76: mt7615: add more uni mcu commands")
Cc: Soul Huang <Soul.Huang@mediatek.com>
Suggested-by: YF Luo <Yf.Luo@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable mac80211 TDLS support by default. Disable TDLS hw filtering for
mt7615 devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt7615_mcu_add_bss_info routine before mt7615_mcu_sta_add since
the firmware requires the bss is created before the relative sta
Tested-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: YF Luo <yf.luo@mediatek.com>
Suggested-by: Lucy Hsu <lucy.hsu@mediatek.com>
Co-developed-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In VHT mode we can receive larger MPDUs. Increasing the buffer size reduces
fragmentation here, which should improve performance.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize tx_status_data pointer in order to enable Air Time Fairness
for mt7663u chipset
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since usb code can't access device registers in interrupt context, move
rcu_read_lock/rcu_read_unlock in mt7615_poll_tx routine. Moreover loop
over a local msta list in mt7615_mac_sta_poll since mt7663u driver will
not be able to complete the inner while loop before sta_poll_list list
is refilled by mt7615_mac_add_txs/mt7615_mac_fill_rx
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the vif is running in station mode the aid will be passed by mac80211
using bss_conf.aid. Fix aid configuration in mt7615_mcu_wtbl_generic_tlv
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Current mt7663 offload firmware can support up to 32 wtbl entries
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the firmware-own configuration has been applied polling
MT_CONN_HIF_ON_LPCTL register
Fixes: f40ac0f3d3 ("mt76: mt7615: introduce mt7663e support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add return code parsing for the following unified commands:
- MCU_UNI_CMD_DEV_INFO_UPDATE
- MCU_UNI_CMD_BSS_INFO_UPDATE
- MCU_UNI_CMD_STA_REC_UPDATE
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rx-queues debugfs node in order to dump rx queues status.
This would be useful for mcu fw debugging
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make Kconfig entry obvious for MT7663E
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable 802.11 power-save support available in mt7663 firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove IEEE80211_HW_PS_NULLFUNC_STACK capability from mt76_phy_init
routine since 802.11 ps is not currently supported by any devices and it
will conflict with mt7663 ps fw support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For sta mode mac80211 provides aid in vif->bss_conf.aid.
In order to properly support 802.11 power-save, configure correct aid
to mcu during sta association
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing register definitions in order to enable sensitivity tuning
for mt7663 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7663u 802.11ac 2x2:2 chipset to mt7615 driver.
Main difference respect to pcie code base is the usb code needs to
configure wtbl from non-atomic context
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Create mt7615-common module in order to collect shared code between usb
and mmio code. Move the following source files in mt7615-common module:
- main.c
- init.c
- mcu.c
- mac.c
- debugfs.c
- eeprom.c
- trace.c
Create the following source files for mmio only source code and move them
in mt7615e module:
- pci_init.c
- dma.c
- pci_mac.c
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
make mac_work per phy instead of per device and fix a possible deadlock
in mt7615_stop since mt7615_mac_work runs holding mt76 mutex
Fixes: fdd2e57076 ("mt76: mt7615: add dual-phy support for mac80211 ops")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sparse report warnings at mt76_tx_status_unlock() and mt76_tx_status_lock()
warning: context imbalance in mt76_tx_status_lock() - wrong count at exit
warning: context imbalance in mt76_tx_status_unlock() - unexpected unlock
The root cause is the additional __acquire(&dev->status_list.lock)
and __release(&dev->status_list.unlock) called
from inside mt76_tx_status_lock() and mt76_tx_status_unlock().
Remove __acquire(&dev->status_list.lock) annotation
Remove __releases(&dev->status_list.unlock)
Correct &dev->status_list.unlock to &dev->status_list.lock
-unlock not defined in the sk_buff_head struct
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable MSI/MSI-X PCI interrupts by default. This patch has been tested
using Banana Pi r64 board
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With MSI interrupts, IRQs must not be enabled from within the IRQ handler,
because that can lead to lost events.
Defer IRQ processing to a tasklet, which is also responsible for enabling
IRQs (to avoid race conditions against the handler)
Co-developed-by: Soul Huang <Soul.Huang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Soul Huang <soul.huang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix DMA unmap length estimation in mt7615_txp_skb_unmap_hw for mt7622
chipset
Fixes: 6aa4ed7927 ("mt76: mt7615: implement DMA support for MT7622")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Avoid having to attempt hw scan and fall back to software for every scan
on devices/firmware without hw scan support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check that val is not zero before aggr_per estimation in order to avoid a
possible division by 0
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is read from flash, it can contain tx DPD calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the EEPROM data is read from flash, it can contain DC offset calibration
data. Add support for sending the data to the firmware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The reference driver does not seem to enable it by default, only under certain
conditions, e.g. when a .bin file is loaded.
Make it opt-in via a device tree property for now, in case it is needed on some
boards.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The function “platform_get_irq” can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211/hostapd runs mt7615_set_channel with the same channel
parameters sending multiple rdd commands overwriting the previous ones.
This behaviour is causing tpt issues on dfs channels.
Fix the issue checking new channel freq/width with the running one.
Fixes: 5dabdf71e9 ("mt76: mt7615: add multiple wiphy support to the dfs support code")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rom patch is shared between Bluetooth and Wifi devices, so correct the
naming to allow two drivers to share the same file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce address parameter to mt7615_eeprom_init routine in order to be
reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Generalize mt7615_rate_desc introducing mt7615_wtbl_desc and
mt7615_key_desc data structures in order to configure the hw wtbl
in a non-atomic context for usb devices
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove key dependency from mt7615_mac_wtbl_update_key and export
mt7615_mac_wtbl_update_key, mt7615_mac_wtbl_update_pk and
mt7615_mac_wtbl_update_cipher in order to reuse them in usb code.
Move mt7615_mac_get_cipher in mac.h
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7615_mac_wtbl_addr in mac.h and add inline qualifier in order to
be reused adding usb support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce __mt7663_load_firmware routine to load firmware for usb
devices.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move register configuration out of mt7615_mac_set_rates since usb
driver can't access device register in interrupt context. Introduce
mt7615_mac_update_rate_desc routine to report rate info to
mt7615_mac_set_rates
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mt7615_write_txwi routine to support usb txwi configuration
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce headroom and tailroom to mt76_mcu_ops data structure in order
to unify the routine used for mcu message allocation. This is a
preliminary patch to add mt7663u support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_wr(dev, MT_CSR(0x010), 0x8208) that would cause
MT_PCIE_IRQ_ENABLE to be disabled; MT_PCIE_IRQ_ENABLE should always keep
on enabled when the driver is running.
0x44064 is a not existing address
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce rlm tlv header in bss_info mcu command in order to
inform the mcu about operating channel. Rlm header is necessary only if
the mcu is running low power functionalities (e.g offloaded scan)
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce BSS absence event that is reported when the fw
is leaving or entering current operational channel.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce scheduled scan support for mt7663e devices
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce hw scan support to mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Keep Rx filters default value if the firmware supports offload and
low power features.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_set_channel_domain routines in order to instruct
the mcu about supported band/channels. This is a preliminary patch to
add hw scan support to mt7663e driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable dfs RDD mcu commands for mt7663 driver since they are not
currently supported by the 7663 firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make scs configurable per phy since most of the chipsets do not
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable Noise floor estimation for mt7663 driver
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mib macros and use proper type for related counters.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7610 PCI id found on D-Link DWR-960 to pci_device_id table.
Run-tested on D-Link DWR-960 with no-name half-size mPCIE card
with mt7610e.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce Mercury UD13 dual-band dongle support to mt76x2u driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current version has a new USB ID and reports as an 0x7632 device.
Adding the IDs results in it working out of the box.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a MCU timeout occurs before a hw restart completes, another hw restart
is scheduled, and the station state gets corrupted.
To speed up dealing with that, do not issue any MCU commands after the first
timeout, and defer handling timeouts until the reset has completed.
Also ignore errors in MCU commands during start/config to avoid making user
space fail on this condition. If it happens, another restart is scheduled
quickly, and that usually recovers the hardware properly.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507192647.GA16710@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507191926.GA15970@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507190210.GA15375@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185914.GA15124@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185529.GA14639@embeddedor
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507185451.GA14603@embeddedor
caps_buf is always of size sizeof(*caps) because
sizeof(caps->auth_encr_pair) * 16 is always zero. Notice
that when using zero-length arrays, sizeof evaluates to zero[1].
So, the code introduced by
commit 0308383f95 ("rndis_wlan: get max_num_pmkids from device")
is logically dead, hence is never executed and can be removed. As a
consequence, the rest of the related code can be refactored a bit.
Notice that this code has been out there since March 2010.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200505235205.GA18539@embeddedor
Link: https://lore.kernel.org/r/20200507110741.37757-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1785:5-8:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508074351.19193-1-yanaijie@huawei.com
Fix sparse warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2206:5:
warning: symbol 'brcmf_p2p_get_conn_idx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508013249.95196-1-chenzhou10@huawei.com
When plumbing rxiv for (GTK) keys, current code does not use seq/seq_len
when present nor set iv_initialized for iovar wsec_key. This could
result in missing broadcast traffic after GTK rekey. The fix is setting
iv_initialized and using seq/seq_len for iovar wsec_key.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-4-git-send-email-wright.feng@cypress.com
The driver sends an action frame down and waits for dwell time to be
completed or aborted before sending out the next action frame.
Driver issues "scan abort" to cancel the current time slot, but this
doesn't have any effect because, we are not using scan engine for
sending action frame.
Fix is to use "actframe_abort" to cancels the current action frame.
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-3-git-send-email-wright.feng@cypress.com
Host driver parses and sets security params into FW passed by
supplicant. This has to be done after reiniting interface in the
firmware.
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-2-git-send-email-wright.feng@cypress.com
802.1d defines 0,3 for BE and 1,2 for BK. In pcie dongles, 0 & 3 are
mapped to 0 and 1,2 are mapped to 1. This change corrects this mapping,
so that BE & BK are given access precedence accordingly by pcie dongles.
Signed-off-by: Pramod Prakash <pramod.prakash@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-3-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151120.GA4469@embeddedor
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508075323.81128-1-weiyongjun1@huawei.com
Pointer info is being assigned twice, once at the start of the function
and secondly when it is just about to be accessed. Remove the redundant
initialization and keep the original assignment to info that is close
to the memcpy that uses it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507164318.56570-1-colin.king@canonical.com
gcc-10 correctly points out a bug with a zero-length array in
struct ath10k_pci:
drivers/net/wireless/ath/ath10k/ahb.c: In function 'ath10k_ahb_remove':
drivers/net/wireless/ath/ath10k/ahb.c:30:9: error: array subscript 0 is outside the bounds of an interior zero-length array 'struct ath10k_ahb[0]' [-Werror=zero-length-bounds]
30 | return &((struct ath10k_pci *)ar->drv_priv)->ahb[0];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/ath/ath10k/ahb.c:13:
drivers/net/wireless/ath/ath10k/pci.h:185:20: note: while referencing 'ahb'
185 | struct ath10k_ahb ahb[0];
| ^~~
The last addition to the struct ignored the comments and added
new members behind the array that must remain last.
Change it to a flexible-array member and move it last again to
make it work correctly, prevent the same thing from happening
again (all compilers warn about flexible-array members in the
middle of a struct) and get it to build without warnings.
Fixes: 521fc37be3 ("ath10k: Avoid override CE5 configuration for QCA99X0 chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-2-arnd@arndb.de
gcc-10 started warning about out-of-bounds access for zero-length
arrays:
In file included from drivers/net/wireless/ath/ath10k/core.h:18,
from drivers/net/wireless/ath/ath10k/htt_rx.c:8:
drivers/net/wireless/ath/ath10k/htt_rx.c: In function 'ath10k_htt_rx_tx_fetch_ind':
drivers/net/wireless/ath/ath10k/htt.h:1683:17: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'struct htt_tx_fetch_record[0]' [-Wzero-length-bounds]
1683 | return (void *)&ind->records[le16_to_cpu(ind->num_records)];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/htt.h:1676:29: note: while referencing 'records'
1676 | struct htt_tx_fetch_record records[0];
| ^~~~~~~
Make records[] a flexible array member to allow this, moving it behind
the other zero-length member that is not accessed in a way that gcc
warns about.
Fixes: 22e6b3bc5d ("ath10k: add new htt definitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-1-arnd@arndb.de
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151921.GA5083@embeddedor
In case of error, 'qcom_wcnss_open_channel()' must be undone by a call to
'rpmsg_destroy_ept()', as already done in the remove function.
Fixes: 5052de8def ("soc: qcom: smd: Transition client drivers from smd to rpmsg")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507043619.200051-1-christophe.jaillet@wanadoo.fr
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507041127.GA31587@embeddedor
Bus level header files needs to be abstracted by upper
layer. Remove bus layer includes by adding appropriate header
files.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-4-govinds@codeaurora.org
Current design supports only AHB interface for
11ax chipset. Refactor the code by adding hif layer
for bus level abstraction to support PCI based device.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-2-govinds@codeaurora.org
Sparse warned:
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: warning: incorrect
type in assignment (different base types)
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: expected
restricted __le32 [usertype] reset_after_request
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: got unsigned int
[usertype] reset
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Fixes: 0f7cb26830 ("ath10k: add rx bitrate report for SDIO")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588747649-18051-1-git-send-email-kvalo@codeaurora.org
gcc-10 warns about accesses inside of a zero-length array:
drivers/net/wireless/ath/wil6210/cfg80211.c: In function 'wil_cfg80211_scan':
drivers/net/wireless/ath/wil6210/cfg80211.c:970:23: error: array subscript 255 is outside the bounds of an interior zero-length array 'struct <anonymous>[0]' [-Werror=zero-length-bounds]
970 | cmd.cmd.channel_list[cmd.cmd.num_channels++].channel = ch - 1;
| ~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/ath/wil6210/wil6210.h:17,
from drivers/net/wireless/ath/wil6210/cfg80211.c:11:
drivers/net/wireless/ath/wil6210/wmi.h:477:4: note: while referencing 'channel_list'
477 | } channel_list[0];
| ^~~~~~~~~~~~
Turn this into a flexible array to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200505143332.1398524-1-arnd@arndb.de
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588667015-25490-1-git-send-email-pillair@codeaurora.org
The qmi infrastructure sends the client a del_server
event when the client releases its qmi handle. This
is not the msg indicating the actual qmi server exiting.
In such cases the del_server msg should not be processed,
since the wifi firmware does not reset its qmi state.
Hence skip the processing of del_server event when the
driver is unloading.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588663061-12138-1-git-send-email-pillair@codeaurora.org
The driver is not handling monitor status descriptor whenever
the done bit of status descriptor is not set by hardware. This leave
a stale entry in monitor status ring and flooding warning message.
Fix that by removing the descriptor and move forward to next one
in monitor status ring.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588642063-6950-1-git-send-email-rmanohar@codeaurora.org
There are several "flavors" of HW that have the same HW type, but
can be told apart after reading a certain perph register. This
is easy to do in runtime, but more complicated to do when looking
at the logs offline.
To make it easier to tell apart these "flavors" when looking at
the dumped dbg info, add these bits to the HW type, allowing
simple differentiation.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.330ea11d17ae.Ie59b25430a308090b15112ac6deedf4fbf487ff1@changeid
We don't really expect fragmented RBs, and don't seem to be seeing
them in practice since that would've caused a crash. Nevertheless,
we should be expecting the hardware to send them.
Parse the flag indicating a fragmented buffer, but then discard it
and any fragments thereof, at least for now. We need to do more
work in the higher layers to properly deal with this, since we may
not get "normal" firmware notifications that are fragmented, only
RX, and then we need to put it back together and add the necessary
API to report a chain of things to the higher layers, this doesn't
fit into the struct iwl_rx_cmd_buffer today.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.e78a59f70b1d.Ica656a98a4e4220d73edc97600edd680cbc97241@changeid
We can currently end up transmitting on an unallocated queue, if
the allocation fails. Stop doing that, by simply not transmitting.
We don't have any better strategy here, unfortunately, but the
previous commits make that much less likely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.dcf1801f25ef.I6d71e13ea042765800f2ee41401b8eb282527c34@changeid
When we have 256 block-ack support, we may need to be very fast
to provide a lot of frames to the hardware to transmit, but that
cannot be guaranteed. Use a longer queue size to have more time,
and the next possible queue size is 1024 since it must be a power
of two.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.851866c7e4c4.I13fa678929431f1694fd202c1da40aa476ab70fe@changeid
Since the recent patch in this area, we no longer allocate 64k
for a single queue, but only 1k, which still means a full page.
Use a DMA pool to reduce this further, since we will have a lot
of queues in a typical system that can share pages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.6e84c79aea30.Ie9a417132812d110ec1cc87852f101477c01cfcb@changeid
We currently attempt to allocate queues that are 512 entries long,
but that requires 32 KiB memory, which may not be available, at
least not contiguously. If we fail to allocate, attempt to use a
smaller queue all the way down to 16 entries (which fit into a
single page).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.c8548d7cc08a.I5059c410e628726cbce98d6311b690c632d00f97@changeid
The hardware needs a byte-count table with the size of each frame
on the queue to build A-MPDUs, but:
* newer generation no longer have the duplicated space at the end,
they can deal with the wrap properly - and we don't even fill
the dup anyway
* we have a maximum queue size of 512 right now and don't use the
theoretical hardware maximum of 65536.
Together, this reduces the byte count table DMA allocation from
64KiB (65536*2 + 64*2 rounded up) to 1 KiB (though that might be
rounded up to a full 4 KiB page by the allocator, not sure it can
share the allocations.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.c263b787b5ab.I059507a9760b1ce1d45d84dcaa91629a5cfb58e0@changeid
Used for debugging what FW API we are using to understand misalignment
with API changes.
The output looks like this as a yaml format
fw_api_ver:
0x0001:
name: MVM_ALIVE
cmd_ver: 99
notif_ver: 4
0x0108:
name: PHY_CONTEXT_CMD
cmd_ver: 2
notif_ver: 0
...
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424194456.18bf540ab8e0.I6217488f1740f0e6accd0cecd09dfd46bad88426@changeid
For ACK_ENABLED and 32BIT_BA_BITMAP flags check the station capabilities
rather than bss_conf.ack_enabled and bss_conf.multi_sta_back_32bit.
These fields are stations capabilities and should not be in bss_conf.
Also note that the bss_conf flags are set in station mode only.
In the next patch I will remove ack_enabled and multi_sta_back_32bit
from the bss_conf structure.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.bc7230b74f93.I144f73cd6a797a7060429981fee62572861bc76b@changeid
If we set amsdu_len one after another the second one overwrites
the orig_amsdu_len so allow only moving from debug to non debug state.
Also the TLC update check was wrong: it was checking that also the orig
is smaller then the new updated size, which is not the case in debug
amsdu mode.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.e565446a4fce.I9729d8c520d8b8bb4de9a5cdc62e01eb85168aac@changeid
This module parameter should not be mangled by users.
This relates to a very old driver and I doubt people can
really check the antenna coupling in a way that would make
the BT Coexistence work better with a real value.
Drop it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.6e566897ce0a.I8395a50c1c39522e542366064bff33a33009ce7b@changeid
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is dead for more than 10 years. Remove it.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/rf.c:476:6-14: WARNING:
Comparison to bool
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/rf.c:54:5-22: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113321.41118-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/pio.c:768:10-25: WARNING: Comparison
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113311.41026-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/b43/phy_n.c:5510:19-32: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113300.40895-1-yanaijie@huawei.com
Currently there is a check if priv is null when calling lbtf_remove_card
but not in a previous call to if_usb_reset_dev that can also dereference
priv. Fix this by also only calling lbtf_remove_card if priv is null.
It is noteable that there don't seem to be any bugs reported that the
null pointer dereference has ever occurred, so I'm not sure if the null
check is required, but since we're doing a null check anyway it should
be done for both function calls.
Addresses-Coverity: ("Dereference before null check")
Fixes: baa0280f08 ("libertas_tf: don't defer firmware loading until start()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200501173900.296658-1-colin.king@canonical.com
gcc-10 reports a warning for mwifiex_cmd_802_11_key_material_v1:
drivers/net/wireless/marvell/mwifiex/sta_cmd.c: In function 'mwifiex_cmd_802_11_key_material_v1':
cc1: warning: writing 16 bytes into a region of size 0 [-Wstringop-overflow=]
In file included from drivers/net/wireless/marvell/mwifiex/sta_cmd.c:23:
drivers/net/wireless/marvell/mwifiex/fw.h:993:9: note: at offset 0 to object 'action' with size 2 declared here
993 | __le16 action;
| ^~~~~~
As the warning makes no sense, I reported it as a bug for gcc. In the
meantime using a temporary pointer for the key data makes the code easier
to read and stops the warning.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94881
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430213101.135134-4-arnd@arndb.de
The variable 'rtlpriv->rfkill.rfkill_state' is bool and can directly
assigned to bool values.
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1725:14-42: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429140924.7750-1-yanaijie@huawei.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1060:6-12:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113357.41422-1-yanaijie@huawei.com
It was observed that P2P Cert. 5.1.19: DEVUT responds to Service
Discovery request failed due to DUT did not send GAS Comeback Response
after receiving request from test bed P2P peer. To fix this issue,
we need to add P2P Action Frame retry delay to enhance P2P connection
under VSDB and noisy environment, since the peer can be in other
channels under VSDB.
Signed-off-by: Justin Li <Justin.Li@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-4-git-send-email-wright.feng@cypress.com
P2P group formation fails since either peer is not able to send go-neg
confirm or dut is not able to send go-neg response. To fix this, retry
limit should be increased and dwell time check should be added.
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-3-git-send-email-wright.feng@cypress.com
With RSDB feature, firmware is able to support two P2P-AGO or two
P2P-GC at the same time. So we add the second p2p connection type
to map to the second P2P connection bsscfg.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-2-git-send-email-wright.feng@cypress.com
the related system resources were not released when pci_iomap() return
error in the rtw_pci_io_mapping() function. add pci_release_regions() to
fix it.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504083442.3033-1-zhengdejin5@gmail.com
Interface configuration table is used to configure PCI PHY that are
normally decided by design or bootstrap pin, and driver can do additional
settings by this table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-9-yhchuang@realtek.com
DIG sets only one IG register for most chips, but 8723D need to set
additional register for CCK rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-8-yhchuang@realtek.com
This ops is used to do statistics of false alarm periodically, and then
fine tune RX initial gain to adaptive different circumstance.
There are three steps, hold/get/reset counter, to retrieve false alarm
counters that consist of CCK and OFDM. In addition to false alarm
counters, it also collects CRC ok/error counters of CCK, OFDM and HT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-7-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
TX status report of 8723D differs from 8822B/8822C, it uses
C2H_CCX_TX_RPT (0x03) with different format. With sequence number
and TX status, driver can know if certain packet was transmitted
successfully.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-5-yhchuang@realtek.com
Set MAC/BB/RF register according to specified channel. The function
rtw_set_channel_mac() is used to set MAC registers, but 8723D only need
some of them.
For channel 14, we need to set different CCK DFIR values, so restore the
values when channel 1 to 13 is selected.
Spur calibration is needed in channel 13 and 14, and we do notch if spur
is over threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-4-yhchuang@realtek.com
This ops is used to parse RX descriptor to know the length of received
packet and containing PHY status. If PHY status is existing, the order is
RX descriptor, PHY status and then packet.
There are two types of PHY status, named CCK and OFDM. Their size are the
same, but formats are different.
struct ieee80211_rx_status is also filled depends on above information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-3-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial gain
depends on field situation. Since each chip has its own register address,
this commit defines 8723d specific address.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-2-yhchuang@realtek.com
Fix the following coccicheck warning:
drivers/net/wireless/ray_cs.c:2797:5-14: WARNING: Comparison of 0/1 to
bool variable
drivers/net/wireless/ray_cs.c:2798:2-11: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426103709.6730-1-yanaijie@huawei.com
The 'blocked' is a bool variable, and '==' expression itself is bool
too. So no need to convert it to 0/1.
This fixes the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/base.c:508:13-41: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094115.23294-1-yanaijie@huawei.com
Axe a memory allocation failure log message. This message is useless and
incorrect (vmalloc is not used here for the memory allocation)
This has been like that since the very beginning of this driver in
commit 43f66a6ce8 ("Add ipw2200 wireless driver.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424154527.27309-1-christophe.jaillet@wanadoo.fr
It's incorrect to use usleep in atomic context.
Switch to a macro which uses udelay instead of usleep to prevent the issue.
Fixes: 6343a6d4b2 ("rtw88: Add delay on polling h2c command status bit")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423073007.3566-1-kai.heng.feng@canonical.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504201224.GA32282@embeddedor
Some devices like TP-Link TL-WN722N produces this kind of messages
frequently.
kernel: ath: phy0: Short RX data len, dropping (dlen: 4)
This warning is useful for developers to recognize that the device
(Wi-Fi dongle or USB hub etc) is noisy but not for general users. So
this patch make this warning to debug message.
Reported-By: Denis <pro.denis@protonmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207539
Fixes: cd486e627e ("ath9k_htc: Discard undersized packets")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504214443.4485-1-masashi.honma@gmail.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504200838.GA31974@embeddedor
This patch add supports to reset the per peer htt stats.
Usage:
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/<peer MAC addr>/htt_peer_stats_reset
While doing so, sync the wmi services between FW and host.
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588610147-20231-1-git-send-email-tamizhr@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
htt stats are not working after htt peer stats display
and also after htt peer stats reset. Trying to dump htt
stats shows "Resource temporarily unavailable".
This is because of "ar->debug.htt_stats.stats_req" member is being
consecutively used for all htt stats without being reset
during the previous usage. Hence assigning NULL to this member
after freeing the allocated memory fixes the issue.
console logs below:
# echo 9 >/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
9
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats
cat: can't open '/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats'
: Resource temporarily unavailable
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588592755-10427-1-git-send-email-ssreeela@codeaurora.org
Fix the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:2964:1-39: WARNING: Assignment
of 0/1 to bool variable
drivers/net/wireless/ath/ath11k/dp_rx.c:2965:1-38: WARNING: Assignment
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113336.41249-1-yanaijie@huawei.com
Add the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-4-git-send-email-pillair@codeaurora.org
Move the msa resources setup out of qmi init and
setup the msa resources as a part of probe before
the qmi init is done.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-3-git-send-email-pillair@codeaurora.org
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
As the exisiting CE configurations are defined in global, there
are the chances of QCA99X0 family chipsets CE configurations
are getting changed by the ath10k_pci_override_ce_config()
function.
The override will be hit and CE5 configurations will be changed,
when the user bring up the QCA99X0 chipsets along with QCA6174
or QCA9377 chipset. (Bring up QCA99X0 family chipsets after
QCA6174 or QCA9377).
Hence, fixing this issue by moving the global CE configuration
to radio specific CE configuration.
Tested hardware: QCA9888 & QCA6174
Tested firmware: 10.4-3.10-00047 & WLAN.RM.4.4.1.c3-00058
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587649759-14381-1-git-send-email-mkenna@codeaurora.org
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
In doing this, make brcmf_debugfs_add_entry() return void as no one was
even paying attention to the return value.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafał Miłecki" <rafal@milecki.pl>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429101526.GA2094124@kroah.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:2359:6-40:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094053.23132-1-yanaijie@huawei.com
Miracast Certification clause 6.1.2 may fail if there is no WFD IE in
p2p assoc response. This change allows WFD IE to be added to p2p assoc
response.
Related WFA certification:
6.1.2 P-SnUT operating as a Group Owner accepts a WFD Session with a
Reference Source
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-6-git-send-email-chi-hsien.lin@cypress.com
P2p spec mentioned that the p2p device address should be the globally
administered address with locally administered bit set. Therefore,
follow this guideline by default.
When the primary interface is set to a locally administered address, the
locally administered bit cannot be set again. Generate a random locally
administered address for this case.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-5-git-send-email-chi-hsien.lin@cypress.com
Send p2p presence response from the p2p interface address instead
of the p2p device address. This is needed for p2p cert 6.1.9 to pass.
Signed-off-by: Madhan Mohan R <MadhanMohan.R@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-4-git-send-email-chi-hsien.lin@cypress.com
The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
When starting station mode on wlan0 and AP mode on wlan1, the apsta will
be disabled and cause data stall on wlan0(station). The apsta feature
with MCHAN(Multi-Channel Concurrent) or RSDB(Real Simultaneous
Dual-Band) can make STA+AP work on two bands concurrently.
Because of that, we keep apsta enabled if firmware supports MCHAN or
RSDB features
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-2-git-send-email-chi-hsien.lin@cypress.com
There are spelling mistakes in two rtw_err error messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424084733.7716-1-colin.king@canonical.com
Update RTL8822C devices' phy tables to v50.
The new parameters introduces new RFE type 5 for some new modules.
Also added a new regulatory CN for power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424073812.26896-1-yhchuang@realtek.com
In Multi-AP VAP scenario with frequent interface up-down, there is a
chance that ath11k_mgmt_over_wmi_tx_work() will dequeue a skb
corresponding to currently deleted/stopped vdev.
FW will assert on receiving mgmt_tx_wmi cmd for already deleted vdev.
Hence adding validation checks for arvif present on the corresponding
ar before sending mgmt_tx_wmi cmd.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588049126-1490-2-git-send-email-murugana@codeaurora.org
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: d0998eb84e ("ath11k: optimise ath11k_dp_tx_completion_handler")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104621.23752-1-weiyongjun1@huawei.com
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5d ("ath10k: add large size for BMI download data for SDIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com
* TX queue debugfs improvements;
* Support for a few new FW API versions;
* Remove deprecated scan FW API version;
* New hw configs and other related changes;
* Support for NPK buffers in debugging;
* More debugging fetures;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=b15k
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-04-24-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of iwlwifi patches intended for v5.8
* TX queue debugfs improvements;
* Support for a few new FW API versions;
* Remove deprecated scan FW API version;
* New hw configs and other related changes;
* Support for NPK buffers in debugging;
* More debugging fetures;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 24 Apr 2020 04:39:43 PM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- use copyright symbol;
- use :field: markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- use copyright symbol;
- use :field: markup;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- use copyright symbol;
- add a document title;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 takes care of rate control for the Beacon frames, so all
mac80211_hwsim needs to do here is advertise support for this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200425155713.25687-5-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While mac80211_hwsim does not need this to configure RX filters, it is
convenient to have this enabled for testing purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200425155713.25687-3-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For legacy mode, tx bitrate not show correct sometimes, for example:
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 19672 bytes (184 packets)
TX: 9851 bytes (87 packets)
signal: -51 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 2.8 MBit/s
This patch use the tx bitrate info from WMI_TLV_PEER_STATS_INFO_EVENTID
report from firmware, and tx bitrate show correct.
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 13973 bytes (120 packets)
TX: 6737 bytes (57 packets)
signal: -52 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 54.0 MBit/s
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, it is enabled only for
"qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-5-wgong@codeaurora.org
The rate code and rate kbps report by WMI_TLV_PEER_STATS_INFO_EVENTID
from firmware contains all the bitrate info which include OFDM, CCK,
HT/VHT, and mac80211 need the struct rate_info which include below
parameters:
flags: bitflag of flags from &enum rate_info_flags
mcs: mcs index if struct describes an HT/VHT/HE rate
legacy: bitrate in 100kbit/s for 802.11abg
nss: number of streams (VHT & HE only)
bw: bandwidth (from &enum rate_info_bw)
For OFDM/CCK, its rate kbps indicate the bitrate, for HT/VHT, mac80211
need the above 5 parameters to cacluate the bitrate and show by iw.
After parse the bitrate info, iw show the correct rx bitrate:
localhost ~ # iw wlan0 link
rx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
rx bitrate: 40.5 MBit/s MCS 2 40MHz
rx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 54.0 MBit/s
rx bitrate: 48.0 MBit/s
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-4-wgong@codeaurora.org
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
For wmi tlv type, firmware disable peer stats info by default, after
enable it, firmware will report WMI_TLV_PEER_STATS_INFO_EVENTID if
ath10k send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware.
Enable it will only set a flag in firmware, firmware will not report
it without receive request WMI command.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-2-wgong@codeaurora.org
The '>' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath5k/ani.c:504:56-61: WARNING: conversion to
bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094037.23048-1-yanaijie@huawei.com
ADC & I/Q calibrations could take infinite time to comple, since they
depend on received frames. In particular the I/Q mismatch calibration
requires receiving of OFDM frames for completion. But in the 2.4GHz
band, a station could receive only CCK frames for a very long time.
And while we wait for the completion of one of the mentioned
calibrations, the NF calibration is blocked. Moreover, in some
environments, I/Q calibration is unable to complete until a correct
noise calibration will be performed due to AGC behaviour.
In order to avoid delaying NF calibration on forever, limit the maximum
duration of ADCs & I/Q calibrations. If the calibration is not completed
within the maximum time, it will be interrupted and a next calibration
will be performed. The code that selects the next calibration has been
reworked to the loop so incompleted calibration will be respinned later.
Ð maximum calibration time of 30 seconds was selected to give the
calibration enough time to complete and to not interfere with the long
(NF) calibration.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-7-ryazanov.s.a@gmail.com
Previously after the calibration validity period is over,
calibrations are invalidated in a one at time manner. So, for AR9002
family, which has three calibrations, the full recalibration interval
becomes 3 x ATH_RESTART_CALINTERVAL. And each next calibration will be
separated by the ATH_RESTART_CALINTERVAL time from a previous one.
It seems like it is better to do whole recalibration at once. Also, this
change makes the driver behaviour a little simpler. So, invalidate all
calibrations at once at the end of the calibration validity interval.
This change affects only AR9002 chips family, since the AR9003 utilize
only a single calibration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-6-ryazanov.s.a@gmail.com
NF calibration and other elements of long calibration are usually faster
than ADCs & I/Q calibrations due to independence of receiption of the
OFDM signal. Moreover sometime I/Q calibration can not be completed at
all without preceding NF calibration. This is due to AGC, which has a
habit to block a weak signal without regular NF calibration. Thus, we do
not need to deferr the long calibration forever.
So, if the long calibration is requested, then deferr the ADCs & I/Q
calibration(s) and run the longcal (the NF calibration in particular) to
obtain fresh noise data.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-5-ryazanov.s.a@gmail.com
Each of AGC & I/Q calibrations can take a long time. Long calibration
and NF calibration in particular are forbiden for parallel run with
ADC & I/Q calibrations. So, the chip could not be ready to perform the
long calibration at the time of request. And a request to perform the
long calibration may be lost.
In order to fix this, preserve the long calibration request as a
calibration state flag and restore the long calibration request each
time the calibration function is called again (i.e. on each subsequent
ivocation of the short calibration).
This feature will be twice useful after the next change, which will
make it possible to start the long calibration before all ADCs & I/Q
calibrations are completed.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-4-ryazanov.s.a@gmail.com
The NFCAL_PENDING flag is set by the ath9k_hw_start_nfcal() routine,
so there is no reason to set it manually after calling it during the
AR9002 calibrations initialization.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-3-ryazanov.s.a@gmail.com
ADC calibration is only required for a 80 MHz sampling rate (i.e. for
40 MHz channels), when the chip utilizes the pair of ADCs in interleved
mode. Calibration on a 20 MHz channel will never be completed.
Previous channel check is trying to exclude all channels where the
calibration will get stuck. It effectively blocks the calibration run
for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g.
legacy mode channels).
Fix this issue by reworking the channel check to explicitly allow ADCs
gain & DC offset calibrations for HT40 channels only. Also update the
complicated comment to make it clear that these calibrations are for
multi-ADC mode only.
Stuck ADCs calibration blocks the NF calibration, what could make it
impossible to work in a noisy evironment: too big Rx attentuation,
invalid RSSI value, etc. So this change is actually more of a NF
calibration fix rather then the ADC calibration fix.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
sparse warnings: (new ones prefixed by >>)
>> drivers/net/wireless/realtek/rtw88/mac.c:653:5: sparse: sparse:
symbol '__rtw_download_firmware' was not declared. Should it be static?
>> drivers/net/wireless/realtek/rtw88/mac.c:817:5: sparse: sparse:
symbol '__rtw_download_firmware_legacy' was not declared. Should it be
static?
Fixes: 15d2fcc6b2 ("rtw88: add legacy firmware download for 8723D devices")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424101255.28239-1-yhchuang@realtek.com
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
-----BEGIN PGP SIGNATURE-----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=SKNj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three changes:
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add framework for supporting specific PHY filter configuration,
which allows for application of various FW defined PHY filters
(one per antenna). Change phy_cfg_cmd to the new API (ver3).
Reading of configuration from platform's ACPI tables to be added
later when tables are defined.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200418110539.242a8f979592.I13c77a8a8dbf1a169b5052c7af1f8401ff3991ad@changeid
