Since the recent patch in this area, we no longer allocate 64k
for a single queue, but only 1k, which still means a full page.
Use a DMA pool to reduce this further, since we will have a lot
of queues in a typical system that can share pages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.6e84c79aea30.Ie9a417132812d110ec1cc87852f101477c01cfcb@changeid
On newer hardware, the tx_queue debugfs file would need to
allocate 37.5kib data since there are 512 queues, which is
too much. Rather than resorting to kludges like kvmalloc(),
use the seq_file API to print out the data.
While at it, also fix a NULL pointer dereference here, the
txq pointer from trans_pcie->txqs[] may be NULL if that
queue hasn't been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200417131727.491cf8224c49.I7f154d81e5becef3b5ff22d7c6e36170bde0d7d5@changeid
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the read_config32 op to allow dumping the config space when
needed.
Change-Id: Ib2d254a38a4bfb95dcc3d04eec91781827a0c623
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----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=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
L0S states have been found to be unstable with our devices and in
newer hardware they are not supported at all, so we must always set
the L0S_DISABLED bit. Previously we were only disabling L0S states if
L1 was supported, because the assumption was that transitions from L0S
to L1 state was the problematic case. But now we should never use
L0S, so do it regardless of whether L1 is supported or not.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit has been misnamed since the initial implementation of the
driver. The correct semantics is that setting this bit disables L0S
states, and we already clearly use it as such in the code. Rename it
to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have only 2k RBs like on the latest (AX210) hardware, then
even on x86 where PAGE_SIZE is 4k we currently waste half of the
memory.
If this is the case, return partial pages from the allocator and
track the offset in each RBD (to be able to find the data in them
and remap them later.)
This might also address other platforms with larger PAGE_SIZE by
putting more RBs into a single large page.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need to map *everything* of the RX buffers, we won't use
that much, map only the part we're going to use. This save some
IOMMU space (if applicable and it can deal with that) and also
prepares a bit for mapping partial pages for 2K buffers later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable bufsz is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new debug TLVs API preprocessing.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow collecting monitor data in ini debug mode.
Implement both SMEM and DRAM monitor regions dumping.
For DRAM monitor, support DBGC1, DBGC2 and DBGC3 and support several
DRAM fragments per DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Legacy DRAM monitor does not support multi buffers.
Remove this infra.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't handle failures in the rb_allocator workqueue allocation
correctly. To fix that, move the code earlier so the cleanup is
easier and we don't have to undo all the interrupt allocations in
this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We got a crash in iwl_trans_pcie_get_cmdlen(), while the TFD was
being accessed to sum up the lengths.
We want to access the TFD here, which is the information for the
hardware. We always only allocate 32 buffers for the cmd queue,
but on newer hardware (using TFH) we can also allocate only a
shorter hardware array, also only 32 TFDs. Prior to the TFH, we
had to allocate a bigger TFD array but would make those point to
a smaller set of buffers.
Additionally, now max_tfd_queue_size is up to 65536, so we can
access *way* out of bounds of a really only 32-entry array, so
it crashes.
Fix this by making the TFD index depend on which hardware we are
using right now.
While changing the calculation, also fix it to not use void ptr
arithmetic, but cast to u8 * before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the
local argument that we received. This will allow us to not to set the
cfg during iwl_trans_alloc() so it can be decided later.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is always set to IWL_PLAT_PM_MODE_DISABLED
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We have a too generic condition that switches from Qu configurations
to QnJ configurations. We need to exclude some configurations so that
they are not erroneously switched. Add the ax201 configuration to the
list of exclusions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows where the driver checks if it runs in ini mode.
Some of these flows are no longer used in ini mode or there is another
condition that check the ini mode in the same flow. Either way, those
conditions are redundant. Remove the redundant conditions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we dump only the first 64 bytes of the PCI config space,
which leaves out some important things, such as the base address
registers.
Increase it to 352 for the PCI device and to 524 for the rootport to
make sure we include everything we need.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Improve the robustness of the dump collection flow in case of an early
error:
1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if
they were already enabled
2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only
if the device is enabled
3. check Tx command queue was already allocated before trying to collect it
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 22000 series FW that was meant to be used with hr is
also the FW that is used for hr1 and has a different RF ID.
Add support to load the hr FW when hr1 RF ID is detected.
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and chainge few cards structs names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add few PCI ID'S for 22000 and fix the wrong name for one
of the structs
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver attempts to clear persistence bit on any device familiy even
though only 9000 and 22000 families require it. Clear the bit only on
the relevant device families.
Each HW has different address to the write protection register. Use the
right register for each HW
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 8954e1eb22 ("iwlwifi: trans: Clear persistence bit when starting the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will let us introduce a mechanism to start with rfkill
faked, and put 0 here to override it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug prints to the ini flow and rewrite existing prints to provide
more information
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses msix causes-register to handle both msix and non msix
interrupts when performing sync nmi. On devices that do not support
msix this register is unmapped and accessing it causes a kernel panic.
Solve this by differentiating the two cases and accessing the proper
causes-register in each case.
Reported-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new configuration with a new firmware name for quz devices.
And, since these devices have the same PCI device and subsystem IDs,
we need to add some code to switch from a normal qu firmware to the
quz firmware.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to perform monitor dumping on AX210 device family
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only add the size of the tx command to the dump file size if it is set
in the dump_mask.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rename few structs to fit the new marketing names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow modules from outside pcie to call sync_nmi.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a few PCI ID'S for 22000 and killer series in addition to
chainging the marketing name.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When flushing TX queues no new TX should go into the system.
However, in the following scenario we get TX:
1. Queues are stopped and there are packets in overflow queue
2. Station is removed and flush begins
3. Flush empties space, and reclaim path TXes SKB from overflow
queue.
Note that the fact the queues are stopped during the process
doesn't matter - the packet will be TXed since the TX path
doesn't care if TX queues are stopped or not, just if there is
space in the queue, which there is, since we just freed a
packet.
A fix here is rather complicated, since the flow is very racy.
Change code not to warn if we are TXing from overflow TX.
In case there is TX from both overflow TX and TX path we will
miss a warning we optimally had, but we can live with that.
Make sure we don't return before overflow queue is empty, otherwise
we will think queues are empty, but they will be refilled, resulting
with assert.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 3955525d5d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Both iwl_trans_fw_error and iwl_force_nmi initiate async recovery flow.
Calling them both is redundant and causing a race.
Solve this by removing the call to iwl_trans_fw_error.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: cfadc3ffcc ("iwlwifi: pcie: stop the firmware when we restart it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.
Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.
since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.
Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409ba3 ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
That's what we pass, and we don't want/need any negative values.
Found by sparse/smatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we use a dumping mask, checking if only monitor was requested
is redundant. Remove the unneeded code.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function was only used by 9000 A-step devices, which we don't
support anymore, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the cfg struct names is mistakenly "iwl22000", when it should
be "iwl22560".
Chage-Id: If9fbfa4bceef81d028c90c98d47115fbe39da547
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Fixes: 2f7a386319 ("iwlwifi: rename the temporary name of A000 to the official 22000")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices with PCI ID 0x2723, which is supposed to be 22260, are
actually not. So we need to differentiate them by checking the hw_rev
and change the cfg accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't populate the array prop on the stack but instead make it static.
Makes the object code smaller by 30 bytes:
Before:
text data bss dec hex filename
80138 15382 576 96096 17760 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
After:
text data bss dec hex filename
79948 15542 576 96066 17742 drivers/net/wireless/intel/iwlwifi/pcie/trans.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW debug data will oneshot read all data available in DRAM
and fill the supplied user buffer. In case the read request
is greater than the new data in DRAM, the driver will write
all data it has and return the buffer immediately.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have to choose different configuration and different firmwares
depending on the external RF module that is installed. Since the
external module is not represented in the PCI IDs, we need to change
the configuration at runtime, after checking the RF ID of the module
installed. We have a bit of a mess in the code that does this,
because it applies cfg's according to the RF ID only, ignoring the
integrated module that is in use.
Fix that for some devices by adding correct configurations for them
and not ignoring the integrated module's type when making the
decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In D3 suspend flow in 9260 gen2 HW, the NIC receives two PERST signals.
The first PERST is expected and indicates the device on coming resume flow.
The second PERST causes FW restart FW restart.
In order to avoid this issue, the FW set the persistence bit on.
Once this bit is set, the FW ignores reset attempts.
The problem is when the FW gets assert during D3 and then the persistence
bit is set and causes the FW to ignore reset.
To handle this issue, the FW opens the preg bit which allows access
to the persistence bit, so that the driver clear the persistence bit
and reset the NIC.
The flow is as follows:
the driver checks if the persistence bit is set.
If the bit is set, the driver checks if he can clear the bit.
If the driver can not clear the bit then there is no point to continue
configuring the NIC since it will fail.
The fix was added is in start HW flow instead of the resume flow since in
general, if the persistence bit is set, the driver can not start the FW.
So it is good to check it when we start configuring the NIC.
The driver does not need to close the preg bit since the FW close it
during the start flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices we will have more than one debug buffer.
Prepare the infrastructure for allocation and release of
multiple debug buffers by grouping the variables in an array
of structures and moving it to trans section, where they will
be visible to opmode and FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
