Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't fill in phy_data.d1 in no-data RX, and thus we
pretend some data is actually filled in radiotap when it
isn't or has default (zero) values.
Fill in phy_data.d1 appropriately, and while at it also
move the info_type initialization into the initializer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.3d488885f77c.Ib97a2bc57c1e9fb98927dc6f802568db313abe3b@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's been a while that the firmware uses LONG_GROUP by default
and not LEGACY_GROUP.
Until now the firmware wrongly advertise the WOWLAN_GET_STATUS
command's version with LEGACY_GROUP, but it is now being fixed.
In order to support both firmwares, first try to get the version
number of the command with the LONG_GROUP and if the firmware
didn't advertise the command version with LONG_GROUP, try to get
the command version with LEGACY_GROUP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.cd6f4e421430.Iec07c746c8e65bc267e4750f38e4f74f2010ca45@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These two version updates deprecate the need to set/get the nonqos sequence
counter during suspend/resume flow respectively; NICs supporting this
version maintain this counter internally and don't lose it during the
suspend/resume flow.
Note that this means that for such NICs the NON_QOS_TX_COUNTER_CMD is no
longer ever sent.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.dd25dd667798.I8db9adcdbb133304b58cf417f8698611138c83b4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating in AP mode with NICs supporting the AP_LINK_PS hw flag,
mac80211 doesn't need to start/stop queueing tx for connected stations
because the FW already handles that.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.64df994c8fbb.I0fa5cda3a5f893a396eef30a01522422be359e69@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of unbinding, the FW would remove the session protection time
events without sending a notification, so explicitly cancel the
session protection, so future requests for mgd_prepare_tx() would not
assume that the session protection is running.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.7c30f85ed241.Ibc19fdbefca7135f2c4ea83d0aef6b81b5033dcd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the UNII4 setting from the ACPI table and use it in the
LARI_CONFIG_CHANGE_CMD accordingly.
This setting allows OEMs to enable or disable UNII4, bypassing the FW
defaults.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.223090c509c4.If03cb5393607ae494041b6187bcec134d6a1e06d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the session protection ends and the Driver is not
associated or a beacon was not heard, the Driver
prints "No beacons heard...".
That's confusing for the case where not associated.
Change the print when not associated to "Not associated...".
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.41a5a5a894fa.I9eabb76e7a3a7f4abbed8f2ef918f1df8e825726@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware can now request SMPS (due to thermal conditions), add
some code to honour such requests and bubble them up through the
stack, subject to our other SMPS constraints, e.g. from Bluetooth.
Then, if the firmware requests SMPS, then we know that it supports
a small extension to the PHY configuration API where a chain mask
of 0 means "use 1 but pick which one yourself", so in this case we
use that extension.
During firmware restart, we stay in the previous state, and the FW
will send us a notification at startup (only) if the temperature is
below the lower or above the high threshold, to sync the state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.85656b7684b9.I7a661a0758d070a750d3a91874d1a0f5fab9febc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
SMPS requests may differ per interfaces due to e.g. Bluetooth
only interfering on 2.4 GHz, so if that's the case we should,
in the case of multiple PHY contexts, still allow RX diversity
on PHY context that have no interfaces with SMPS requests.
Fix the code to pass through the PHY context in question and
skip interfaces with non-matching PHY context while iterating.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.123c6b05809d.I992e3d1c6a29850d02eeec01712b5b685b963a87@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have a P2P Device active, we attempt to only change the
PHY context it uses when we get a new remain-on-channel, if the
P2P Device is the only user of the PHY context.
This is fine if we're switching within a band, but if we're
switching bands then the switch implies a removal and re-add
of the PHY context, which isn't permitted by the firmware while
it's bound to an interface.
Fix the code to skip the unbind/release/... cycle only if the
band doesn't change (or we have old devices that can switch the
band on the fly as well.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.e9ac313f70f3.I713b9d109957df7e7d9ed0861d5377ce3f8fccd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the new BIOS DSM and Pass to FW if to disable\enable
11ax for Russia according to the BIOS key. This is
needed to enable OEMs to control enable/disable 11ax in Russia.
Also add support for future "enable 11ax in country X" features.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.a705f7cedff8.I580f1021cabcc37e88f5ec5e9a6bbf00aae514b6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas
Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of
a couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał
Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well
as the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of
cleanups and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmCRqDIACgkQqDIjiipP
6E8O2Qf5AQvSVoN9WYRBLo1+a4mkGsJ/wHQMEsOA4FVHft5/QVkRtpMNbSiyq00O
YTpNuoBqiYm/tSTyzK/5Oh+0ucgm/ef4c4dTyPjZYw2GB+3rYNRAXdX/tB6Ggjl/
oUArUCoSQZjOU6Y573B05rcHp1PVM/XL9LgD1uX76tXA1MaGvsyC0cyPRAdOANke
W83BWI0XMhv8B1bZwHVB2Oft5x6HhqWBl3HKbNOmPEMtwkqqBCFAqB0wNEH88ZTf
2hyBjBoZQHdMkJsC0piMvIyAjHZiIjQB47VWz31EvKB3/E28xCqRqPViPq9QbrA5
got0+oDbxI96T024ndXRomc0SSxZnw==
=5THg
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Remove duplicate error message for the amlogic driver (Tang Bin)
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of a
couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well as
the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of cleanups
and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
* tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (55 commits)
thermal/drivers/mtk_thermal: Remove redundant initializations of several variables
thermal/core/power allocator: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Lock the thermal zone while looping over instances
thermal/core/power_allocator: Update once cooling devices when temp is low
thermal/core/power_allocator: Maintain the device statistics from going stale
thermal/core: Create a helper __thermal_cdev_update() without a lock
dt-bindings: thermal: tsens: Document ipq8064 bindings
thermal/drivers/tsens: Add support for ipq8064-tsens
thermal/drivers/tsens: Drop unused define for msm8960
thermal/drivers/tsens: Replace custom 8960 apis with generic apis
thermal/drivers/tsens: Fix bug in sensor enable for msm8960
thermal/drivers/tsens: Use init_common for msm8960
thermal/drivers/tsens: Add VER_0 tsens version
thermal/drivers/tsens: Convert msm8960 to reg_field
thermal/drivers/tsens: Don't hardcode sensor slope
Documentation: driver-api: thermal: Remove thermal_notify_framework from documentation
thermal/core: Remove thermal_notify_framework
iwlwifi: mvm: tt: Replace thermal_notify_framework
dt-bindings: thermal: brcm,ns-thermal: Convert to the json-schema
...
thermal_notify_framework just updates for a single trip point where as
thermal_zone_device_update does other bookkeeping like updating the
temperature of the thermal zone and setting the next trip point etc.
Replace thermal_notify_framework with thermal_zone_device_update as the
later is more thorough.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-2-thara.gopinath@linaro.org
It is not very useful to WARN if we can't send a host command
The firmware is likely in a bad situation and the fact that
we didn't send the host command has an impact on the firmware
only, not on the driver. The driver could clean up all its
state.
Don't WARN in this case, but just leave a smaller note.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.0324abc169c8.I4f9b769bc38d68f8ed43f77d2cd75e8f1993e964@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we switch channel, we may miss a few beacons on the
new channel. Don't disconnect if the time event for the
switch ends before we hear the beacons.
Note that this is relevant only for old devices that still
use the TIME_EVENT firmware API for channel switch.
The check that we hear a beacon before the time event
ends was meant to be used for the association time event
and not for the channel switch time event.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411132130.3d710091a0bd.I37a161ffdfb099a10080fbdc3b70a4deb76952e2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We cannot lock a mutex while we're in an RCU critical section. At
the same time, we're accessing data structures that are protected
by the mvm->mutex anyway, so just move the entire locking here to
use only that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.4d27bd36e10e.I1fd8e8fe442c41a5deaa560452b598ed7a60ada5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Power save (PS) should only be enabled when we reach the max phy rate.
Before we reach it (MCS_9) for VHT, we should keep trying to improve the
throughput.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.2a2fb9f9c25e.I7c7bbcfbdc1d35d2c3338778fb397dd5b08ea0e8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
umac_error_table In TLV address was read using mask on MSB
but on the same table in alive message it was without which
caused mismatch in devices with different memory region MSB
Signed-off-by: Roee Goldfiner <roee.h.goldfiner@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210411124417.179fee442115.Ib6eabe86cfda0b6044f07c07448c366b6e07e53d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of implementing the DSM evaluation function in the MVM code,
refactor it so it can be generalized and part of the common ACPI
implementation.
Signed-off-by: Harish Mitty <harish.mitty@intel.com>
[reworded subject and commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.a24af3551aac.I8e6bd5eb05f853b6331fa4823750f7ba8ffe46e6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the new BIOS DSM and Pass to FW if to disable\enable
11ax for Ukraine according to the BIOS key. this is
needed to enable OEMs to control enable/disable 11ax in Ukraine
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.055654e7707e.If7eaf9839cd5d59729a235df07e31668b408e740@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for ppag in China by reading revision 2 of the ppag table
from ACPI, and passing the data to the FW.
This is needed to enable OEMs to control ppag enablement
in China.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.69af388d0dce.I8cfddf9e6837bf394b00390181b4b774ded19acd@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do queue sync, it's confusing that we have the structures
declared in the FW API header files that aren't really firmware,
and the union is also confusing - especially now in the code that
checks the size on the return.
So rework this: change the type of sync and whether to do it in a
synchronous fashion to arguments, and build the data structure in
the function, so we don't need the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.f62833fd9893.I612d7ac1c655ec4880329360e15d207698c750bc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.d11c9bcdb4aa.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"Fully associated" means that we heard a beacon with the DTIM
information and the firmware is configured to track the beacons.
Since the firmware needs to track the beacons for the CSA, we
can't configure the firmware for CSA before it knows when the
beacons are expected otherwise we'd get ASSERT 301D.
If we are required to start CSA before we told the firmware
when the beacons are expected to arrive, just report a
failure and let mac80211 disconnect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.9adaedeb59e4.Idaad6aaf3f9759d023b8e00b10064915c0db9aa3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When moving to the new channel, we block TX until we hear the
first beacon. if it is not heard, we proceed to disconnect.
Since TX is blocked (without mac80211 being aware of it) the frame
is stuck, resulting with queue hang.
Instead, reenable TX before reporting on the connection loss.
As we are on the new channel, there is no problem with that,
even if the original CSA had quiet mode.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210330162204.eb4f2ff1b863.Ib16238106b33d58b2b7688dc6297018b915ecef4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unfortunately, since beacon protection isn't fully available
yet, we didn't notice that there are problems with it and
that the replay detection isn't working correctly. We were
relying only on mac80211, since iwl_mvm_rx_crypto() exits
when !ieee80211_has_protected(), which is of course true for
protected (but not encrypted) management frames.
Fix this to properly detect protected (but not encrypted)
management frames and handle them - we continue to only care
about beacons since for others everything can and will be
checked in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: b1fdc2505a ("iwlwifi: mvm: advertise BIGTK client support if available")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.23c990843369.I09c262a8f6f9852cc8f513cdcb31a7f8f87dd8af@changeid
When The driver in D3 and FW crash happens, trans->system_pm_mode
is not reset to IWL_PLAT_PM_MODE_DISABLED which causes the driver
not to send INIT conmmands and D3 resume fails.
This patch contains the fix for resetting trans->system_pm_mode to
IWL_PLAT_PM_MODE_DISABLED and D3 resume is successful.
Signed-off-by: Ravi Darsi <ravi.darsi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.ad170ad48409.Ifc6b10e8b3f235876af91d0e23e90b462d270eff@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, for all devices and families, failing getting the temp
from the fw is indicated in the log as ERR.
This is too severe for two reasons:
1. The driver has a fall back - and schedules the next temp
read immediately after failing to read temp from the fw.
2. The temp read implementation in the fw is different between
HWs, and on older devices the flow is a-sync and may timeout.
Reducing the print severity from ERR to WARN will allow to
track the issue if it will appear many times, but not frighten users
if it appears once.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210172142.dfd423b2b2ef.Icd576dc3e2e7174d3ed9c1c32f48ea0013699e72@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the NVM until fairly late in the flow and
since this flow will be split soon, get the NVM later to
unite it with the parts that really need it.
Gather all what needs the NVM into a function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.bab0e65c4909.I789f3eb577b216ad1688269e036ce9fa4880f532@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The STA_CTXT_HE_NIC_NOT_ACK_ENABLED flag tells the firmware
whether *we* support ack-enabled.
So what should be checked is our *own* capability and not
the *peer's* capability.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.59f44e210096.I8f31968f6f7303255e212d869ca0131becd309aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Return value of the iwl_mvm_load_nvm_to_nic func is not analyzed. If load
NVM to nic func fails and NVM is not loaded to fw properly, then fw may
behave badly and lead to some strange issue. This commit will analyze
return value and if load NVM to nic has failed, then the error code is
sent to the previous func, which will trigger WRT log collection.
iwl_fw_dbg_error_collect() func collects dump only if tri type is
FW_DBG_TRIGGER_ALIVE_TIMEOUT. But when Load NVM to nic function fails
trig_type is FW_DBG_TRIGGER_DRIVER. This commit also has code changes to
collect dump when trig_type is FW_DBG_TRIGGER_DRIVER.
Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.32998850192a.Ic58d08cb6944ca55e343ff0032c82cfa7821e588@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the firmware support for internal station for auxiliary
activities, there is no need to configure an auxiliary station
as part of SCAN_CFG_CMD. Thus, this configuration was removed
from the corresponding structure.
Align the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.9b8da8408692.I7fe99d73cd67ffc817c2ef6af4c9932ce9fc50b2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the actions that were taken after the registration can
be taken before the registration to mac80211.
This will help to defer part of the op_mode_mvm_start
function to a later stage in case the device is not
available.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.c03cc5db67c1.Ia928ca34d25a73d959a345ffbe4f1217c3f17394@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
BIOS provides RFI feature enable/disable state via WiFi DSM ACPI
object. By default the feature should be disabled.
The GUID for this feature is different from the one driver currently
uses, so need to provide a set of new definitions.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.242bfe368981.Iaccce1e2fa3986b174d0b08942aa4fbf8bb94a95@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.
This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The call to iwl_sar_geo_init() was moved to the end of the
iwl_mvm_sar_geo_init() function, after the table revision is assigned
to the FW command. But the revision is only known after
iwl_sar_geo_init() is called, so we were always assigning zero to it.
Fix that by moving the assignment code after the iwl_sar_geo_init()
function is called.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 45acebf8d6 ("iwlwifi: fix sar geo table initialization")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.cef55ef3a065.If96c60f08d24c2262c287168a6f0dbd7cf0f8f5c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some change conflicts apparently cause a confusion between a local
variable being used to send the PPAG command and the introduction of a
union for this command. Most parts of the local command were never
copied from the stored data, so the FW was getting garbage in the
tables instead of getting valid values.
Fix this by completely removing the local and using only the union
that we have stored in fwrt.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.d090e0301023.I7d57f4d7da9a3297734c51cf988199323c76916d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the PPAG table from ACPI, we should store everything in
our fwrt structure, so it can be accessed later. But we had a local
ppag_table variable in the function and were erroneously storing the
enabled/disabled flag in it instead of storing it in the fwrt. Fix
this by removing the local variable and storing everything directly in
fwrt.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.889862e6d393.I8b894c1b2b3fe0ad2fb39bf438273ea47eb5afa4@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value we receive from ACPI is a long long unsigned integer but the
values should be treated as signed char. When comparing the received
value with ACPI_PPAG_MIN_LB/HB, we were doing an unsigned comparison,
so the negative value would actually be treated as a very high number.
To solve this issue, assign the value to our table of s8's before
making the comparison, so the value is already converted when we do
so.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.b0ec69f312bc.If77fd9c61a96aa7ef2ac96d935b7efd7df502399@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
-----BEGIN PGP SIGNATURE-----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=c570
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
We should only allow PPAG to be enabled by OEMs that are in the
approved list. In order to do this, we need to compare the system
vendor string retrieved from SMBIOS to a list maintained in the
driver. If the vendor string is not in the list, we don't allow PPAG
to be used.
For now the list is empty, but entries will be added to it
individually, in subsequent patches.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.c9d35b7d8748.I4e4cf61d8fa6ff91d9b0cab2b1ec9ede4be346f5@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When version 2 of the PER_PLATFORM_ANT_GAIN_CMD was implemented, we
started copying the values from the command that we have stored into a
local instance. But we accidentally forgot to copy the enabled flag,
so in practice PPAG is never really enabled. Fix this by copying the
flag from our stored data a we should.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f2134f66f4 ("iwlwifi: acpi: support ppag table command v2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.24d7bf754ad5.I0e8abc2b8747508b6118242533d68c856ca6dffb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should only collect debug data after exiting suspend state, that's
why we delete the current place in d3.c file, and add it to fwrt flows
that occur while we can still access the fw and collect debug data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210131201908.eaf378ed403c.I46fae3ee6da1a4b476515b8ad51ad1c0ea2d8381@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Once the all the stations completed the switch, we need
to clear csa_tx_blocked_vif. This was missing. We also
need to re-enable the broadcast / multicast stations.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5b813753bdb.Id58979b678974c3ccf44d8b381c68165ac55a3d3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we abort the scan because of a firmware crash, we
need to cancel the delayed work that monitors the scan
completion. Otherwise it'll kick and try to restart the
firmware yet another time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.a497faa942dd.Ibc155ad36da9de7eb0ddcdd826ddf8dd6607d2ac@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were starting the early time-point too late in non-unified
firmwares. Unlike with unified firmwares, we were starting it only
after reading the NVM, so errors in the NVM read phase were not
logged.
Solve this by moving the time-point to the same place as we do with
unified firmwares, i.e. just before we go into the wait-alive code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.bb6d28ceca01.I770fdf3b9b9fa555fe0935926e32cc3509d980de@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The "supp" variable doesn't need to be unsigned long, only
"tmp" is used with for_each_set_bit(). "supp" should just
be a u16, since that's how it's sent to the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.762e50704a39.I014bc7898f90c734f8e9be2a3efaf9bf8b7db6db@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware has support, then advertise it to the stack and
send the key down. Since we re-check the protection in the host
anyway, we don't really need to do anything on RX except that we
should drop frames that the firmware _knows_ are replay errors,
since beacon filtering might otherwise result in replays being
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5a3d53301b3.I23e84c9bb0b039d9106a07e9d6847776757f9029@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we check the length, we only check that the advertised
data length fits into the data we have, but currently not
that it actually matches correctly.
This should be harmless, but if the first two bytes are zero,
then the iwl_rx_packet_payload_len() ends up negative, and
that might later cause issues if unsigned variables are used,
as this is not something that's normally expected.
Change the validation here to precisely validate the lengths
match, to avoid such issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.5184dfc2a445.I0631d2e4f6ffb93cf06618edb035c45bd6d1d7b9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In roaming flows and during reassociation, its possible that data frames
such as EAPOLs for 4 way handshake/ 802.1x authentication are initially set
to higher MCS rate. Though these are pruned down to a lower legacy rate
before sending to the FW, driver also emits a kernel warning - intended for
non-data frames. Add checks to avoid such warnings for data frames, while
also enhancing the debug data printed.
Signed-off-by: Krishnanand Prabhu <krishnanand.prabhu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.d9ded010c4ce.Ie1d5a33d7175c0bcb35c10b5729748646671da31@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While disconnecting from the AP due to bad channel switch
params (e.g. too long Tx block), do not send the firmware
'CSA abort' before disconnecting. That causes canceling the
immediate quiet and can cause transmitting data before the
disconnection happens.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.b9af359a675f.I996fc7eb3d94e9539f8b117017c428448c42c7ad@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3_CONFIG_CMD and D0I3_END_CMD should be the last\first
command upon suspend\resume correspondingly, otherwise,
FW will raise an assert (0x342).
There are firmware notifications that cause the driver to
send a command back to the firmware. If such a notification
is sent to the driver while the the driver prepares the
firmware for D3, operation, what is likely to happen is that
the handling of the notification will try to get the mutex
and will wait unil the driver finished configuring the
firmware for D3. Then the handling notification will get
the mutex and handle the notification which will lead to
the aforementioned ASSERT 342.
To avoid this, we need to prevent any command to be sent to
the firmware between the D3_CONFIG_CMD and the D0I3_END_CMD.
Check this in the utility layer that sends the host commands
and in the transport layer as well.
Flag the D3_CONFIG_CMD and the D0I3_END_CMD commands as
commands that must be sent even if the firmware has already
been configured for D3 operation.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.1935a993b471.I3192c93c030576ca16773c01b009c4d93610d6ea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop TX'ing because we are suspending, we
have two options: either we check system_pm_mode or we
check the mvm's status that has a bit for the suspend
flow.
The latter is better because test_bit is atomic. Also
add a call to synchronize_net after we set the bit to
make sure that all the new Tx see the bit before we
actually complete the suspend flow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.243c88781302.I5c0379c5a7e5d49410569e7fcd2fff7a419c6dea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the new api all the flush in the FW is done before we
get the response and in the response we only get the updated
read pointer and all queued packets don't get anymore rx_tx
per packet to free the queued packet, so driver needs to free
all queued packets on flushed queue at once after flush response.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4bd0eca8c0ef.I1601aad2eb2cc83f6f73b8ca52be57bb9fd626ab@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When restarting firmware with an ongoing scheduled scan, we
don't (and shouldn't) mark it as aborted as mac80211 will be
restarting it, and so no event should go out to userspace.
The appropriate comment regarding this wasn't moved to this
place, so add it.
However, we _do_ need to clean up our internal state, since
mac80211 will restart the scan, and we'll otherwise get to
the WARN_ON() a few lines below for no reason whatsoever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4ddc9b017268.Ie869b628ae56a5d776eba0e7b7f05f42fc566f2e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing features where the firmware may send some
notifications it can often be a lot easier to do that
from a test script. Remove most injection limitations
from debugfs to be able to do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.9aff3c6b4607.I03b0ae7df094734451445ffcb7f9f0274969f1c0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We shouldn't trust the firmware with the sizes (or contents)
of notifications, accessing too much data could cause page
faults if the data doesn't fit into the allocated space. This
applies more on older NICs where multiple notifications can
be in a single RX buffer.
Add a general framework for checking a minimum size of any
notification in the RX handlers and use it for most. Some RX
handlers were already checking and I've moved the checks,
some more complex checks I left and made them _NO_SIZE for
the RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.3e155d5e5f90.I2121fa4ac7cd7eb98970d84b793796646afa3eed@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes allover the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgD96RAAoJEG4XJFUm622bubwH/2TxF5aLNnE49BdgksiorD1M
lr6r1QveG/VQkSVdecYV6wmJ/nzzR46Q3c7Ez3ZBnLpboSDmyK7gKIeGlHSLmMwC
YYt3Fnj1XF/UgPs+daCiF/yxz3v7lsDicl8wKYQgpKU/jDj8dfQ/ntM5p3s0tc5O
JaiWeDGQQRgbyE9g3enqW0vho/6luxI0MIOwcSnCLidsM6oAQowbmtzXDpmwagiR
Xyi0eLzSHSCOmH41VNphDZzlL61C6yCLavNpCvCxv/bElTX7XXynwiw3+i8FiU14
TQabyv0z0yd3pVCYp88TFf9cDe7uQ8MS6NG5CoYP3RXHJ1pDEy3a8yBBc1dp2Tc=
=a+lu
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
Second set of fixes for v5.11. Like in last time we again have more
fixes than usual Actually a bit too much for my liking in this state
of the cycle, but due to unrelated challenges I was only able to
submit them now.
We have few important crash fixes, iwlwifi modifying read-only data
being the most reported issue, and also smaller fixes to iwlwifi.
mt76
* fix a clang warning about enum usage
* fix rx buffer refcounting crash
mt7601u
* fix rx buffer refcounting crash
* fix crash when unbplugging the device
iwlwifi
* fix a crash where we were modifying read-only firmware data
* lots of smaller fixes all over the driver
* tag 'wireless-drivers-2021-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers: (24 commits)
mt7601u: fix kernel crash unplugging the device
iwlwifi: queue: bail out on invalid freeing
iwlwifi: mvm: guard against device removal in reprobe
iwlwifi: Fix IWL_SUBDEVICE_NO_160 macro to use the correct bit.
iwlwifi: mvm: clear IN_D3 after wowlan status cmd
iwlwifi: pcie: add rules to match Qu with Hr2
iwlwifi: mvm: invalidate IDs of internal stations at mvm start
iwlwifi: mvm: fix the return type for DSM functions 1 and 2
iwlwifi: pcie: reschedule in long-running memory reads
iwlwifi: pcie: use jiffies for memory read spin time limit
iwlwifi: pcie: fix context info memory leak
iwlwifi: pcie: add a NULL check in iwl_pcie_txq_unmap
iwlwifi: pcie: set LTR on more devices
iwlwifi: queue: don't crash if txq->entries is NULL
iwlwifi: fix the NMI flow for old devices
iwlwifi: pnvm: don't try to load after failures
iwlwifi: pnvm: don't skip everything when not reloading
iwlwifi: pcie: avoid potential PNVM leaks
iwlwifi: mvm: take mutex for calling iwl_mvm_get_sync_time()
iwlwifi: mvm: skip power command when unbinding vif during CSA
...
====================
Link: https://lore.kernel.org/r/20210126092202.6A367C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/core/tso.c got recent support for USO, and this broke iwlfifi
because the driver implemented a limited form of GSO.
Providing ->gso_type allows for skb_is_gso_tcp() to provide
a correct result.
Fixes: 3d5b459ba0 ("net: tso: add UDP segmentation support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209913
Link: https://lore.kernel.org/r/20210125150949.619309-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we get into a problem severe enough to attempt a reprobe,
we schedule a worker to do that. However, if the problem gets
more severe and the device is actually destroyed before this
worker has a chance to run, we use a free device. Bump up the
reference count of the device until the worker runs to avoid
this situation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.871f0892e4b2.I94819e11afd68d875f3e242b98bef724b8236f1e@changeid
In D3 resume flow, avoid the following race where sending
packets before updating the sequence number (sequence
number received from the wowlan status command response):
Thread 1:
__iwl_mvm_resume clears IWL_MVM_STATUS_IN_D3 and is cut
by thread 2 before reaching iwl_mvm_query_wakeup_reasons.
Thread 2:
iwl_mvm_mac_itxq_xmit calls iwl_mvm_tx_skb since
IWL_MVM_STATUS_IN_D3 is not set using a wrong sequence number.
Thread 1:
__iwl_mvm_resume continues and calls iwl_mvm_query_wakeup_reasons
updating the sequence number received from the firmware.
The next packet that will be sent now will cause sysassert 0x1096.
Fix the bug by moving 'clear IWL_MVM_STATUS_IN_D3' to after
sending the wowlan status command and updating the sequence
number.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.fe927ec939c6.I103d3321fb55da7e6c6c51582cfadf94eb8b6c58@changeid
Having sta_id not set for aux_sta and snif_sta can potentially lead to a
hard to debug issue in case remove station is called without an add. In
this case sta_id 0, an unrelated regular station, will be removed.
In fact, we do have a FW assert that occures rarely and from the debug
data analysis it looks like sta_id 0 is removed by mistake, though it's
hard to pinpoint the exact flow. The WARN_ON in this patch should help
to find it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5dc6dd9b22d5.I2add1b5ad24d0d0a221de79d439c09f88fcaf15d@changeid
The return type value of functions 1 and 2 were considered to be an
integer inside a buffer, but they can also be only an integer, without
the buffer. Fix the code in iwl_acpi_get_dsm_u8() to handle it as a
single integer value, as well as packed inside a buffer.
Signed-off-by: Matt Chen <matt.chen@intel.com>
Fixes: 9db93491f2 ("iwlwifi: acpi: support device specific method (DSM)")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210122144849.5757092adcd6.Ic24524627b899c9a01af38107a62a626bdf5ae3a@changeid
In the new CSA flow, we remain associated during CSA, but
still do a unbind-bind to the vif. However, sending the power
command right after when vif is unbound but still associated
causes FW to assert (0x3400) since it cannot tell the LMAC id.
Just skip this command, we will send it again in a bit, when
assigning the new context.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130252.64a2254ac5c3.Iaa3a9050bf3d7c9cd5beaf561e932e6defc12ec3@changeid
Also add documentation for 'mvm'.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:400: warning: cannot understand function prototype: 'const u16 expected_tpt_legacy[IWL_RATE_COUNT] = '
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'mvm' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'tbl' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'scale_index' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'attempts' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'successes' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:684: warning: Function parameter or member 'window' not described in '_rs_collect_tx_data'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2677: warning: duplicate section name 'NOTE'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'mvm' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'lq_sta' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2682: warning: Function parameter or member 'band' not described in 'rs_initialize_lq'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'mvm' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:3761: warning: Function parameter or member 'lq_sta' not described in 'rs_program_fix_rate'
drivers/net/wireless/intel/iwlwifi/mvm/rs.c:4213: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_tx_protection'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126133152.3211309-3-lee.jones@linaro.org
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly using the fallthrough pseudo-keyword as a
replacement for a number of "fall through" markings.
Notice that Clang doesn't recognize "fall through" comments as
implicit fall-through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201117135053.GA13248@embeddedor
When waiting for a notification and then processing it,
we also need to check the size of the data before we use
it. Most places do that already, but fix the remaining
ones to do it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b29573bcba39.I4b7e72824d06dc0719a40021d933e29edfc14713@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification has several versions. Check the
notification size according to the expected notification version.
Notifications with incorrect size will be ignored.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.ee57c3214d05.I810d7de33fb08001ef1a2e24714d5b68932e088e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previously, we added checks that the contained MPDU size is long
enough, but really we should also check that the notification
itself fits into the data. Add some checks for that.
Also add unlikely() annotations on the previously added checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.51cc04cf1e3e.I7bfd6809f8f5feb75f79397646e6656e95688a0e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the channel switch delay that we would incur after the channel
switch actually happens is longer than the quiet time we're willing
to tolerate, disconnect as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.3bc3449922da.Ib0255deb67b2fc21317e274adcacb545bb1dc669@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some races in the hardware that can possibly lead to
a bus lockup later during a restart when we manage to kill the
firmware at a bad time (while it's accessing the bus).
To work around this, add support for a new handshake between
firmware and driver to ensure that the firmware is in a well-
known state before we kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a channel switch with a very long quiet period, we schedule
a work to disconnect after a while. This work runs in background. In the
meanwhile, we keep getting beacons and sending FW modify command for each.
This has a potential race, where we modify the CSA after we aborted it.
Protect the flow by setting csa_failed to true in case we abort, and check
it before sending the modify command.
This required a modification to the way we treat csa_failed in
iwl_mvm_post_channel_switch:
1. The variable isn't being reset anymore, so we can still look at it in
iwl_mvm_channel_switch_rx_beacon. This is fine, since we reset it when
starting a new CSA.
2. There is no more early return in case of csa_failed. This is fine,
since before this patch csa_failed was set only for GO, and for GO the
function is only resetting the power settings, which we want to restore
even in case of failure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b023856bdf39.I4ed0149e0018fe5e1ae3c2a1cbc614954016063f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We send some data to the firmware and expect to get it back,
but we shouldn't really trust the firmware on this. Check the
size of all the data we send down to avoid using bad or just
uninitialized data when the firmware doesn't respond right.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.a5a8173f16c7.I4fa68bb2b1c7dcc52ddd381c4042722d27c4a34d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We keep the scan status per UID in scan_uid_status field when the
iwl_mvm_build_scan_cmd() function is called. If we error out after
this, e.g. due to FW restart being in progress, we're not cleaning
up properly, and can run into warnings later.
Clean up internal variables when starting fails after calling the
iwl_mvm_build_scan_cmd() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.970421a2f753.Id62b2da8a0ccccbb114407db82ca485d07749d39@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're currently doing accounting on the queue sync with an
atomic variable that counts down the number of remaining
notifications that we still need.
As we've been hitting issues in this area, modify this to
track a bitmap of queues, not just the number of queues,
and print out the remaining bitmap in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.0a3fa177cd6b.I7c69ff999419368266279ec27dd618eb450908b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MPDU contained in a notification shouldn't be larger than the
notification size itself is, validate this.
Reported-by: Haggai Abramovsky <haggai.abramovsky@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7c721ad37014.Id5746874ecfa208b60baa62691b2d9dc5dd4d89c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Similarly to what I did to iwl_run_init_mvm_ucode, there is no
need to pass the read_nvm parameter. Either we have an NVM
and we don't need to read it, or we don't and we need to read it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.1b764faecfee.I2da0ada577fc16268125a4a15b5e725c18c643ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Curretly we only mark HW error state "after" trying to collect HW data,
but if any HW error happens while colleting HW data we go into endless
loop. avoid this by setting HW error state "before" collecting HW data.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4c7e5a87da15.Ic35b2f28ff08f7ac23143c80f224d52eb97a0454@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to the 6GHz band (aka. Ultra High Band or UHB). This
allows us to scan and connect to channels in that band, including all
the relevant features, such as preferred scan channels, colocated
channels etc.
Co-developed-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Co-developed-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Co-developed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Co-developed-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Signed-off-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201210000657.0fdbfc3d7352.Idb648536faf21716e2ab2c6d6890d3e49f719cd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This command should be used only when there's a real client station.
Currently it works, but since soon the driver will stop actually having
an auxiliary station by default, and this command requires _some_ valid
station, it needs to be removed from this flow.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.81b2acfe292b.I8c7372e6f72279e22966a2d0a9066521f9d2f1a0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Detect and avoid this endless loop.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
We need to feed the configuration id to remove session protection
properly.
Remember the conf_id when we add the session protection so that we
can give it back when we want to remove the session protection.
While at it, slightly improve the kernel doc for the conf_id
of the notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.3642f730333d.I01a98ecde62096d00d171cf34ad775bf80cb0277@changeid
The ROC that runs on the AUX ROC (meaning an ROC on the STA vif),
was added with the HOT_SPOT_CMD firmware command and must be
cancelled with that same command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: fe959c7b20 ("iwlwifi: mvm: use the new session protection command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.a317376154da.I44fa3637373ba4bd421cdff2cabc761bffc0735f@changeid
Currently, our max tpt is limited to max HT A-MPDU for LB,
and max VHT A-MPDU for HB. Configure HE exponent value correctly to
achieve HE max A-MPDU, both on LB and HB.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.4486852ebb56.I9eb0d028e31f183597fb90120e7d4ca87e0dd6cb@changeid
When adding support for version 3 of the GEO_TX_POWER_LIMIT command,
the table argument of iwl_sar_geo_init was changed from a pointer a 1d
array of now-removed iwl_per_chain_offset_group_v1 to a pointer to a 2d
array of iwl_per_chain_offset (iwl_per_chain_offset_group_v1 was a
struct containing 2 copies of iwl_per_chain_offset).
So even for version 2 where the second dimension is of length 2, which
means that the underlying memory layout of the array didn't change, this
requires a small change in the way we loop over it, and this was missed.
Additionally, for the case of version 3 where the second dimension is now
3, in order to fill the first two elements of each row correctly (lb and
hb), iwl_sar_geo_init must get the true number of bands supported.
But because we don't yet store any values for the 3rd (uhb) band, skip
that band.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.73605b6e0548.Id0ec98333277ff9e017e3938ae413b34acc68947@changeid
iwl_mvm_wowlan_program_keys is now setting data directly in
the KEK_KCK command, and the memset is clearing this later,
causing the data to be incomplete.
Just remove the memory clearing, the structure is local and
cleared in the declaration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.0f355b4578c5.Ifbb76a2814925f215a2c889c1792d46d5bd66ab8@changeid
We introduced a new flow to remove an on-going CSA but we
assumed the firwmare understands the
CHANNEL_SWITCH_TIME_EVENT_CMD. This is not true for 7265 and down.
Don't send this command for those devices, but rather use the older
command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.2574e3e47927.Ic0c56411da1096e9a45ee5c3383edf777c5baca0@changeid
ADD_STA_CMD_API_S ver 12 was added in order to properly support
auxiliary activities in CDB NICs. In the new version we don't need
to allocate an aux station at initialization, instead we add an
aux station only when an auxiliary activity that requires a dedicated Tx
queue is needed. For now the only case we need this kind of activity is
when using hot spot 2.0
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.700e6e2e3077.Icdd807b6a3ad3fed806449ea0a13f856aa20e632@changeid
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
The FW relies on the re-enablement of the TX in order to know
it can exit quiet mode. Currently in case of CSA with quiet mode,
the quiet mode is never cancelled, resulting in a complete traffic
hang.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.fee389c83ded.I09550fdadb61f899242d7e7b7578672372e2b7fe@changeid
If we have only a single RX queue, such as when MSI-X is not
available, we should not send the RFH_QUEUEU_CONFIG_CMD, because our
only queue is the same as the command queue and will be configured as
part of the context info. Our code was actually trying to send the
command with 0 queues, which caused UMAC assert 0x1D04.
Fix that by not sending the command when we have a single queue.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.c35eeb3299f8.I08f79a6ebe150a7d180b7005b24504bfdba6d8b5@changeid
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'rate_n_flags' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1379: warning: Function parameter or member 'info' not described in 'iwl_mvm_hwrate_to_tx_status'
drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1431: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_get_scd_ssn'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-14-lee.jones@linaro.org
Fix misnamed, and missing descriptions likely due to doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'lq' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Excess function parameter 'sync' description in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'vif' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'smps_request' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Excess function parameter 'smps_requests' description in 'iwl_mvm_update_smps'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-11-lee.jones@linaro.org
Looks as if it's never been used.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/ops.c:466:36: warning: ‘iwl_mvm_debug_names’ defined but not used [-Wunused-const-variable=]
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-9-lee.jones@linaro.org
Add support for the new version of the alive notification, which
includes the SKU ID. We don't use the SKU ID yet, so we can just
handle the new notification as if it were version 4.
While at it, clean up a bit and rename the command and structure names
in the comments so that they are aligned with the ones used in the FW.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6024b149e9e2.Ifcadb506e994ec352e9ce54399719926bc1bb7ee@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The scan request may specify the request scan dwell time.
However, this value may not always be optimal (e.g. short dwell
time for a passive channel). This may happen in a scan request
as a result of beacon report request, in which the AP may request
an active scan, thus setting a short dwell time, but the station
will perform a passive scan due to regulatory.
Ignore the scan duration parameter and always use the internal
scan dwell time which should be optimal.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.6e1d2b8b4489.I9584bb40d44bf31131f57fdd32d5e8848d4fbdd8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is being updated to report version 11 of this
response in order to include BIGTK material. Parse it, but
for now keep the existing behaviour of disconnecting on any
rekeying with even IGTK presence, need to fix that before
BIGTK can be supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.b7098f097a5c.I4ae1c5b2186b0e04702233a7a7068d69cfd3361a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some bits declared here that simply don't exist
in the firmware, and some are missing (e.g. the key) from
what the firmware has. Align this and move all the fields
into a single one for this status word, which makes this a
bit easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.0ba403d72e7c.I5fa3aa0538f3fbf8c3885b27a1204b5b0464c20a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are printing the same thing twice, "Enabling TXQ #%d". Previously
the second print was including more information, but now it only
prints the queue number, which is already in the first print. Remove
the redundant one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.1c22d1bc0a88.I24e57317bdddc6c72f69725e1d95683a935e893d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The API added the ability to send for CDB nic what LMAC ID
the cmd belongs to.
Also driver always set apply_time to zero so no need to pass it as
a param and anyway in new API it's removed for no use.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fa11d1f523b6.Id105899da82c2b08ee62b57133c4ff72bfd0bb80@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New API for temperature measurement (DTS_MEASUREMENT_TRIGGER)
involves getting an immediate response from FW, and not waiting
for a notification like in previous APIs. Support new API while
keeping backwards compatibility.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.b4893554d8e7.Ia4d7f389d4ac3256fcfe3ce6144e924dd6dbf6eb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add an option for adding a PASN responder, specifying the HLTK and
TK (if not associated). When a receiving a range request for a
PASN responder, the driver will ask for a secured measurement with
the specified HLTK and TK.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.28c5f5266000.I2d58b72ff92c47ac33a6aacc27fbf3790b6dfc51@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For secure ranging with an associated station, the driver only needs
to set the HLTK. There is no need to add an internal station for PMF
since the FW will use the existing station which already has the TK
installed.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.fcebaa5c9bc8.Ic584cc47fee717d0bdb43965798dbdf45d89910a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The overcome instabilities in the RTT results add smoothing logic
to the reported results. In short, the smoothing logic tracks the
RTT average of each responder for a period of time, and in case
a new RTT results is found to be a spur, the tracked RTT average
is reported instead of the current RTT measurement.
Smooth logic debug configuration using iwl-dbg-cfg.ini:
- MVM_FTM_INITIATOR_ENABLE_SMOOTH: Set to 1 to enable smoothing logic
(default=0).
- MVM_FTM_INITIATOR_SMOOTH_ALPHA: A value between 0 - 100, defining
the weight of the current RTT results vs. the RTT average tracked
based on the previous results. A value of 100 means use only the
current RTT results.
- MVM_FTM_INITIATOR_SMOOTH_AGE_SEC: The maximal time in seconds in which
the RTT average tracked based on previous results is considered valid.
- MVM_FTM_INITIATOR_SMOOTH_UNDERSHOOT: if the current RTT is positive
and below the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
- MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT: if the current RTT is positive
and above the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.48a9cec2081b.Iaec1e29f738232adfe9e2ea8e9eb9b6ff0323ae1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Version 11 of the range request command adds support for setting
the PN for secure ranging. For now, this is not yet supported.
The same functions that are used for version 9 and 10 are also
used for version 11 as the common part is the same.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.6f9ed4140e8c.I046e0d9f6dfaafda9794e5eb2ee1f02fcad2851a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For new APIs this avoids checking every return if it's
IWL_FW_CMD_VER_UNKNOWN (99) or it's lower than the new API value
Done with spatch:
-iwl_fw_lookup_cmd_ver(E1, E2, E3)
+iwl_fw_lookup_cmd_ver(E1, E2, E3, IWL_FW_CMD_VER_UNKNOWN)
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.70bec6eb8008.I6ea78553801d33f7ed10fcd2e4be4ba781fe469a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the new version of the GEO_TX_POWER_LIMIT command.
This new version includes UHB values in the table, but for now, since
we don't have the ACPI values yet, we support the API, but don't set
the extra values.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.3700197ed1ed.Ia53fb9c4b5033683fd426d51a0ddc46fb444c805@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the version number to the iwl_geo_tx_power_profile_cmd structs and
move the union into a common place. Additionally, reuse the code that
sets elements that are at the same place in the struct across
different versions.
While at it remove an unused variable, add a comment and move the v2
specific element setting to inside the if statement. Additionally,
invert the if for slightly more readability.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.23ec241f16cd.I8cd21fc5a2498e820b50e1f49a4cbfe545afe30e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new version of the command can support more subbands and CDB, so
it can contain more data than earlier versions. Implement support for
the new version of the command, even though we don't have more data to
write to it yet.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.d709a8f17d1d.I9fa54883667c72dabf6d813c70be77538d9af38d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a common structure to contain all different versions of the
tx_power_cmd instead of making a union of the different structs
everywhere we need them. Also move the common part of these structs
into a separate structure (instead of reusing v3) and leave the
per_chain_restriction part out of the common part, because this will
change in version 6 of the command (which will be added soon).
While at it, rename per_chain_restriction to per_chain to shorten it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.4f0bea9fe077.Ib3b540a8288af32d6fa213448e13f82763f85bc9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On newer hardware, we have the full checksum, so use it to report
CHECKSUM_COMPLETE and avoid the protocol specific hardware parsing.
Note that the hardware already parses/removes the SNAP header, so
we actually literally get what we need to report to the stack, as
we're expected to checksum everything after the L2 header (which
is translated/added by mac80211).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.869e829c815d.I70f374865b0acafc675a8d7959912eeaeb595acf@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have the same info in two variables,
If umac_error_event_table is 0, we know that UMAC log is not supported,
so we don't need the support_umac_log field.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.299959eeb47b.Ie1f3eecc06e3620098dda74f674f6409b90fe7fa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- Change the iwl_all_tsc_rsc struct to hold a sta_id (__le32) field,
while preserving the union, used in the older version.
- Adjust the use of this command according to the TLV.
Signed-off-by: Dan Halperin <Dan1.Halperin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.8c621903db59.I1cc7afedc0ff2009fe1abf007684339f299b73aa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The the driver prevents new Tx from being sent during the remove-station
flow is by invalidating the fw_id_to_mac_id rcu of that station.
However, if there was any Tx still in-flight (tx-cmd was sent but the
ba-notif wasn't received yet) the ba-response to those frames is simply
ignored without actually reclaiming anything. This later causes the
driver to think that that some of the station's queues aren't empty when
in practice they are which causes errors in the station remove flow.
Fix this by performing the tx-reclaim also if the rcu is invalid. any DB
that can't be updated due to this is not very important at this stage
since the station is about to be removed soon anyways.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.72c604b4eda9.I21e75b31a9401870d18747355d4f4305b2fe1db8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
