Commit c134d1f8c4 ("ath11k: Handle errors if peer creation fails") completely
broke AP mode on QCA6390:
kernel: [ 151.230734] ath11k_pci 0000:06:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant[2307]: Failed to set beacon parameters
wpa_supplicant[2307]: Interface initialization failed
wpa_supplicant[2307]: wlan0: interface state UNINITIALIZED->DISABLED
wpa_supplicant[2307]: wlan0: AP-DISABLED
wpa_supplicant[2307]: wlan0: Unable to setup interface.
wpa_supplicant[2307]: Failed to initialize AP interface
This was because commit c134d1f8c4 ("ath11k: Handle errors if peer creation
fails") added error handling for ath11k_peer_create(), which had been failing
all along but was unnoticed due to the missing error handling. The actual bug
was introduced already in commit aa44b2f3ec ("ath11k: start vdev if a bss peer is
already created").
ath11k_peer_create() was failing because for AP mode the peer is created
already earlier op_add_interface() and we should skip creation here, but the
check for modes was wrong. Fixing that makes AP mode work again.
This shouldn't affect IPQ8074 nor QCN9074 as they have hw_params.vdev_start_delay disabled.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: c134d1f8c4 ("ath11k: Handle errors if peer creation fails")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614006849-25764-1-git-send-email-kvalo@codeaurora.org
If CONFIG_ARCH_DMA_ADDR_T_64BIT=n:
drivers/net/wireless/ath/ath11k/qmi.c: In function ‘ath11k_qmi_respond_fw_mem_request’:
drivers/net/wireless/ath/ath11k/qmi.c:1690:8: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 5 has type ‘dma_addr_t’ {aka ‘unsigned int’} [-Wformat=]
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1691 | ab->qmi.target_mem[i].paddr,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| dma_addr_t {aka unsigned int}
drivers/net/wireless/ath/ath11k/debug.h:64:30: note: in definition of macro ‘ath11k_dbg’
64 | __ath11k_dbg(ar, dbg_mask, fmt, ##__VA_ARGS__); \
| ^~~
drivers/net/wireless/ath/ath11k/qmi.c:1690:34: note: format string is defined here
1690 | "qmi req mem_seg[%d] 0x%llx %u %u\n", i,
| ~~~^
| |
| long long unsigned int
| %x
Fixes: d5395a5486 ("ath11k: qmi: add debug message for allocated memory segment addresses and sizes")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210221182754.2071863-1-geert@linux-m68k.org
This reverts commit a56c14bb21.
ath_tx_process_buffer() doesn't dereference or check sta and passes it
to ath_tx_complete_aggr() and ath_tx_complete_buf().
ath_tx_complete_aggr() checks the pointer before use. No problem here.
ath_tx_complete_buf() doesn't check or dereference sta and passes it on
to ath_tx_complete(). ath_tx_complete() doesn't check or dereference sta,
but assigns it to tx_info->status.status_driver_data[0]
ath_tx_complete_buf() is called from ath_tx_complete_aggr() passing
null ieee80211_sta pointer.
There is a potential for dereference later on, if and when the
tx_info->status.status_driver_data[0]is referenced. In addition, the
rcu read lock might be released before referencing the contents.
ath_tx_complete_buf() should be fixed to check sta perhaps? Worth
looking into.
Reverting this patch because it doesn't solve the problem and introduces
memory leak by skipping buffer completion if the pointer (sta) is NULL.
Fixes: a56c14bb21 ("ath9k: fix ath_tx_process_buffer() potential null ptr dereference")
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210217211801.22540-1-skhan@linuxfoundation.org
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Cc: stable@vger.kernel.org
Reported-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210214184911.96702-1-nbd@nbd.name
WMI_CHAN_INFO_DFS_FREQ2 needs to be set in wmi vdev start command chan
info parameter, to enable radar detection for secondary segment in 160MHz.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01717-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613480547-28810-1-git-send-email-lavaks@codeaurora.org
Number of Sounding dimensions config received from firmware for
bandwidth above 80MHz is cleared, and proper value is not set again.
So not resetting it to accept the config from firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01689-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613460136-7170-1-git-send-email-lavaks@codeaurora.org
QCN9074 is PCI based 11ax radio.
- has 2G/5G/6G variants.
- has NSS 2x2 and 4x4 variants.
QCN9074 uses 45MB of HOST DDR memory, target requests host memory in
segments, each segment is of 2MB size and is physcial contiguous and
use static window configuration.
Currently there are still two issues with QCN9074, see below. So we don't add
QCN9074 PCI id yet to make sure the driver is loaded. The id will be added only
after the issues are fixed.
Issue 1:
ath11k_pci 0000:06:00.0: qmi failed memory request, err = -110
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-110
Issue 2:
ath11k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
ath11k_pci 0000:06:00.0: qmi failed set mode request, mode: 0, err = -110
ath11k_pci 0000:06:00.0: qmi failed to send wlan fw mode:-110
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-12-git-send-email-akolli@codeaurora.org
Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org
Define host CE configuration for QCN9074 since the max CE count is six.
Available MSI interrupt is five so cannot able to map the ce_id directly
for the msi_data_idx. Added get_ce_msi_idx ops in ath11k_hif_ops to get
the CE MSI idx which is used to initialize the CE ring.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-10-git-send-email-akolli@codeaurora.org
hal rx descriptor is different for QCN9074 target type. since
rx_msdu_end, rx_msdu_start, rx_mpdu_start elements are in
different placement/alignment. In order to have generic data path,
introduce platform specific hal rx descriptor access ops in
ath11k_hw_ops.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-9-git-send-email-akolli@codeaurora.org
Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org
Three window slots can be configure. First window slot
dedicate for dynamic selection and remaining two slots
dedicate for static selection. To optimise the window
selection, frequent registers (UMAC, CE) are configure
in static window slot. so that we minimise the window
selection. Other registers are configure in dynamic window
slot. Get the window start address from the respective
offset and access the read/write register.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-7-git-send-email-akolli@codeaurora.org
Add MHI config for QCN9074 also populate ath11k_hw_params for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-6-git-send-email-akolli@codeaurora.org
QCN9074 FW requests three types memory segments during the boot,
qmi mem seg type 1 of size 15728640
qmi mem seg type 4 of size 3735552
qmi mem seg type 3 of size 1048576
Segment type 3 is for M3 coredump memory.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-5-git-send-email-akolli@codeaurora.org
QCN9074 firmware uses 20MB of HOST DDR memory, fw requests
the memory in segmnets of size 1MB/512KB/256KB.
Increase the number of fw memory segments to 52.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-4-git-send-email-akolli@codeaurora.org
qmi service_ins_id is unique for QCA6390 and QCN9074,
this is needed for adding QCN9074 support. No functional
changes.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-3-git-send-email-akolli@codeaurora.org
Move ath11k_msi_config to array of structures to add multiple
pci devices support. No functional changes.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-2-git-send-email-akolli@codeaurora.org
ath_tx_process_buffer() references ieee80211_find_sta_by_ifaddr()
return pointer (sta) outside null check. Fix it by moving the code
block under the null check.
This problem was found while reviewing code to debug RCU warn from
ath10k_wmi_tlv_parse_peer_stats_info() and a subsequent manual audit
of other callers of ieee80211_find_sta_by_ifaddr() that don't hold
RCU read lock.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/43ed9abb9e8d7112f3cc168c2f8c489e253635ba.1613090339.git.skhan@linuxfoundation.org
Second set of patches for v5.12. Last time there was a smaller pull
request so unsurprisingly this time we have a big one. mt76 has new
hardware support and lots of new features, iwlwifi getting new
features and rtw88 got NAPI support. And the usual cleanups and fixes
all over.
Major changes:
ath10k
* support setting SAR limits via nl80211
rtw88
* support 8821 RFE type2 devices
* NAPI support
iwlwifi
* add new FW API support
* support for new So devices
* support for RF interference mitigation (RFI)
* support for PNVM (Platform Non-Volatile Memory, a firmware data
file) from BIOS
mt76
* add new mt7921e driver
* 802.11 encap offload support
* support for multiple pcie gen1 host interfaces on 7915
* 7915 testmode support
* 7915 txbf support
brcmfmac
* support for CQM RSSI notifications
wil6210
* support for extended DMG MCS 12.1 rate
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgJl5/AAoJEG4XJFUm622bCrcIAIwarm51aHq8R0Py0ZYBEiIM
STe/x3gjxVhzYHd438APchEMnePY6pWZ6e00GnZwMyWxZpMHK+yOYzWrewLvYI29
qyPFkjGdE6PhYjL+lJjYHn4M1cdAkO4t0FSvCy5OvOnuIgu0Yz3TXXQVxZtrzrIc
2q+bOR1kKaVBe8NOjggnxTWe4mTj6efeTkD0D5M+IbppERtmpcVLra9FSgz5IcLl
hlKyNNtiNo/CmQu0bGejXR7ip+JA08f5No6TOlEQKR6pBvBvwrvgXHsq9rfQO8qA
CDhz4DqfPPYMNXnJuFVAzYsw4raZblwTg5GtIjH7e0cbXxSAx50Ne2Hd850nkO8=
=eQGJ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
Second set of patches for v5.12. Last time there was a smaller pull
request so unsurprisingly this time we have a big one. mt76 has new
hardware support and lots of new features, iwlwifi getting new
features and rtw88 got NAPI support. And the usual cleanups and fixes
all over.
Major changes:
ath10k
* support setting SAR limits via nl80211
rtw88
* support 8821 RFE type2 devices
* NAPI support
iwlwifi
* add new FW API support
* support for new So devices
* support for RF interference mitigation (RFI)
* support for PNVM (Platform Non-Volatile Memory, a firmware data
file) from BIOS
mt76
* add new mt7921e driver
* 802.11 encap offload support
* support for multiple pcie gen1 host interfaces on 7915
* 7915 testmode support
* 7915 txbf support
brcmfmac
* support for CQM RSSI notifications
wil6210
* support for extended DMG MCS 12.1 rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I have received feedback that QCA6390 PCI support is working for many, and I'm
also using QCA6390 on my daily driver^Hlaptop. While there are issues still
to be resolved it's not really experimental anymore, so remove the experimental
warning from driver initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1613040697-20289-1-git-send-email-kvalo@codeaurora.org
ieee80211_find_sta_by_ifaddr() must be called under the RCU lock and
the resulting pointer is only valid under RCU lock as well.
Fix ath10k_wmi_tlv_op_pull_peer_stats_info() to hold RCU lock before it
calls ieee80211_find_sta_by_ifaddr() and release it when the resulting
pointer is no longer needed.
This problem was found while reviewing code to debug RCU warn from
ath10k_wmi_tlv_parse_peer_stats_info().
Link: https://lore.kernel.org/linux-wireless/7230c9e5-2632-b77e-c4f9-10eca557a5bb@linuxfoundation.org/
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210210212107.40373-1-skhan@linuxfoundation.org
Based on the comment block in this function and the FIXME for this, peer
being present for the offchannel tx is unlikely. Peer is deleted once tx
is complete. Change peer present msg to a warn to detect this condition.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/3b1f71272d56ee1d7f567fbce13bdb56cc06d342.1612915444.git.skhan@linuxfoundation.org
The SPR parameter set comprises OBSS PD threshold for SRG
and non SRG and Bitmap of BSS color and partial BSSID. This adds
support to configure fields of SPR element to firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01164-QCAHKSWPL_SILICONZ-1
Tested-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612843714-29174-1-git-send-email-rmanohar@codeaurora.org
ieee80211_report_used_skb of mac80211 use the frame_control of
ieee80211_hdr in sk_buff and indicate it to another function
ieee80211_mgd_conn_tx_status, then it queue work ieee80211_sta_work,
but ieee80211_is_auth(fc) in ieee80211_sta_work check fail when the
authentication has transmitted by ath10k.
When the ath10k report it with HTT_TX_COMPL_STATE_DISCARD, it will be
set without flag IEEE80211_TX_STAT_ACK, then mac80211 should try the
next authentication immeditely, but in fact mac80211 wait 1 second for
it, the reason is ieee80211_is_auth(fc) in ieee80211_sta_work check
fail for the sk_buff which is not restored, the data of sk_buff is not
the begin of ieee80211_hdr, in fact it is the begin of htt_cmd_hdr.
dmesg without this patch, it wait 1 second for the next retry when
ath10k report without IEEE80211_TX_STAT_ACK for authentication:
[ 6973.883116] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 1/3)
[ 6974.705471] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 2/3)
[ 6975.712962] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 3/3)
Restore the sk_buff make mac8011 retry the next authentication
immeditely which meet logic of mac80211.
dmesg with this patch, it retry the next immeditely when ath10k
report without IEEE80211_TX_STAT_ACK for authentication:
[ 216.734813] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 1/3)
[ 216.739914] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 2/3)
[ 216.745874] wlan0: send auth to 5e:6f:2b:0d:fb:d7 (try 3/3)
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612839530-2263-1-git-send-email-wgong@codeaurora.org
This error path leads to a Smatch warning:
drivers/net/wireless/ath/ath11k/mac.c:4269 ath11k_mac_op_start()
error: double unlocked '&ar->conf_mutex' (orig line 4251)
We're not holding the lock when we do the "goto err;" so it leads to a
double unlock. The fix is to hold the lock for a little longer.
Fixes: c83c500b55 ("ath11k: enable idle power save mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[kvalo@codeaurora.org: move also rcu_assign_pointer() call]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YBk4GoeE+yc0wlJH@mwanda
FW reports Tx/Rx extended MCS 12.1 to driver as "26". Driver will
convert this into base MCS 7 + EXTENDED_SC_DMG flag so kernel can do
the correct phy rate conversion. Also add log prints to print "12.1"
instead of "26" for extended MCS.
Signed-off-by: Max Chen <mxchen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1609977050-7089-3-git-send-email-mxchen@codeaurora.org
Add new level ATH10K_DBG_STA debug_mask for printing
sta related logs. This will be useful to check the
debug logs of connection and changes related to
station.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612463738-16542-1-git-send-email-tamizhr@codeaurora.org
Multiple structures in the carl9170 driver have alignment
impossible alignment constraints that gcc warns about when
building with 'make W=1':
drivers/net/wireless/ath/carl9170/fwcmd.h:243:2: warning: alignment 1 of 'union <anonymous>' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/carl9170/wlan.h:373:1: warning: alignment 1 of 'struct ar9170_rx_frame_single' is less than 2 [-Wpacked-not-aligned]
In the carl9170_cmd structure, multiple members that have an explicit
alignment requirement of four bytes are added into a union with explicit
byte alignment, but this in turn is part of a structure that also has
four-byte alignment.
In the wlan.h header, multiple structures contain a ieee80211_hdr member
that is required to be two-byte aligned to avoid alignmnet faults when
processing network headers, but all members are forced to be byte-aligned
using the __packed tag at the end of the struct definition.
In both cases, leaving out the packing does not change the internal
layout of the structure but changes the alignment constraint of the
structure itself.
Change all affected structures to only apply packing where it does
not violate the alignment requirement of the contained structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210204162926.3262598-1-arnd@kernel.org
Tx descriptor search index field should be updated with hw peer id
and not by AST Hash as per the HW/FW recommendation. Incorrect search
index causes throughput degradation in all scenario for all the
platforms. so updated the search index field with hw peer id, which
is a common change applicable for all the platforms. Also no need of these
configuration for non station type. seen 10% throughput increase in WDS
traffic with this change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612410960-9120-1-git-send-email-periyasa@codeaurora.org
The ieee80211_find_sta_by_ifaddr call in
ath10k_wmi_tlv_parse_peer_stats_info must be called while holding the
RCU read lock. Otherwise, the following warning will be seen when RCU
usage checking is enabled:
=============================
WARNING: suspicious RCU usage
5.10.3 #8 Tainted: G W
-----------------------------
include/linux/rhashtable.h:594 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by ksoftirqd/1/16.
stack backtrace:
CPU: 1 PID: 16 Comm: ksoftirqd/1 Tainted: G W 5.10.3 #8
Hardware name: HP Grunt/Grunt, BIOS Google_Grunt.11031.104.0 09/05/2019
Call Trace:
dump_stack+0xab/0x115
sta_info_hash_lookup+0x71/0x1e9 [mac80211]
? lock_is_held_type+0xe6/0x12f
? __kasan_kmalloc+0xfb/0x112
ieee80211_find_sta_by_ifaddr+0x12/0x61 [mac80211]
ath10k_wmi_tlv_parse_peer_stats_info+0xbd/0x10b [ath10k_core]
ath10k_wmi_tlv_iter+0x8b/0x1a1 [ath10k_core]
? ath10k_wmi_tlv_iter+0x1a1/0x1a1 [ath10k_core]
ath10k_wmi_tlv_event_peer_stats_info+0x103/0x13b [ath10k_core]
ath10k_wmi_tlv_op_rx+0x722/0x80d [ath10k_core]
ath10k_htc_rx_completion_handler+0x16e/0x1d7 [ath10k_core]
ath10k_pci_process_rx_cb+0x116/0x22c [ath10k_pci]
? ath10k_htc_process_trailer+0x332/0x332 [ath10k_core]
? _raw_spin_unlock_irqrestore+0x34/0x61
? lockdep_hardirqs_on+0x8e/0x12e
ath10k_ce_per_engine_service+0x55/0x74 [ath10k_core]
ath10k_ce_per_engine_service_any+0x76/0x84 [ath10k_core]
ath10k_pci_napi_poll+0x49/0x141 [ath10k_pci]
net_rx_action+0x11a/0x347
__do_softirq+0x2d3/0x539
run_ksoftirqd+0x4b/0x86
smpboot_thread_fn+0x1d0/0x2ab
? cpu_report_death+0x7f/0x7f
kthread+0x189/0x191
? cpu_report_death+0x7f/0x7f
? kthread_blkcg+0x31/0x31
ret_from_fork+0x22/0x30
Fixes: 0f7cb26830 ("ath10k: add rx bitrate report for SDIO")
Signed-off-by: Anand K Mistry <amistry@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210202134451.1.I0d2e83c42755671b7143504b62787fd06cd914ed@changeid
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJgHW7nAAoJEG4XJFUm622bgd0IAKtEBcjfqnR2wW7Rt6Ah/Uch
vInrZ+5YOhjamoCvZHhTwdvUEmuRYJBT8ZqfO5x3X0GlIaJe1PlJhlvOs/9PkQ9G
eMSFcy1D/uSb3KoRRLq8lNaAy7NAyajg11IhRAeQFLeBkZgI43PGq6j7sbYCerah
87trNNlHagio9p4q9FGXVtJ2cJGQdNHM8jn4dw5Uue45YArkhj6VBh3EZl9dqV+F
XmxK+qvIcK1KPzw6nZ/0dGf8B6dnXaljn0cAzAo8QPSaZI+jozY52y3XdoKVqYRF
ekqDra4Xl/uKVZR1vb2jE5T/NtmzZI63uifndL6esEjwJMrrkRy9+alHwIxt2rU=
=KZD7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.12
First set of patches for v5.12. A smaller pull request this time,
biggest feature being a better key handling for ath9k. And of course
the usual fixes and cleanups all over.
Major changes:
ath9k
* more robust encryption key cache management
brcmfmac
* support BCM4365E with 43666 ChipCommon chip ID
* tag 'wireless-drivers-next-2021-02-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (35 commits)
iwl4965: do not process non-QOS frames on txq->sched_retry path
mt7601u: process tx URBs with status EPROTO properly
wlcore: Fix command execute failure 19 for wl12xx
mt7601u: use ieee80211_rx_list to pass frames to the network stack as a batch
rtw88: 8723de: adjust the LTR setting
rtlwifi: rtl8821ae: fix bool comparison in expressions
rtlwifi: rtl8192se: fix bool comparison in expressions
rtlwifi: rtl8188ee: fix bool comparison in expressions
rtlwifi: rtl8192c-common: fix bool comparison in expressions
rtlwifi: rtl_pci: fix bool comparison in expressions
wlcore: Downgrade exceeded max RX BA sessions to debug
wilc1000: use flexible-array member instead of zero-length array
brcmfmac: clear EAP/association status bits on linkdown events
brcmfmac: Delete useless kfree code
qtnfmac_pcie: Use module_pci_driver
mt7601u: check the status of device in calibration
mt7601u: process URBs in status EPROTO properly
brcmfmac: support BCM4365E with 43666 ChipCommon chip ID
wilc1000: fix spelling mistake in Kconfig "devision" -> "division"
mwifiex: pcie: Drop bogus __refdata annotation
...
====================
Link: https://lore.kernel.org/r/20210205161901.C7F83C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210128144928.2557605-1-trix@redhat.com
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210127222344.2445641-1-trix@redhat.com
When CONFIG_ATH9K is built-in but LED support is in a loadable
module, both ath9k drivers fails to link:
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_deinit_leds':
gpio.c:(.text+0x36): undefined reference to `led_classdev_unregister'
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_init_leds':
gpio.c:(.text+0x179): undefined reference to `led_classdev_register_ext'
The problem is that the 'imply' keyword does not enforce any dependency
but is only a weak hint to Kconfig to enable another symbol from a
defconfig file.
Change imply to a 'depends on LEDS_CLASS' that prevents the incorrect
configuration but still allows building the driver without LED support.
The 'select MAC80211_LEDS' is now ensures that the LED support is
actually used if it is present, and the added Kconfig dependency
on MAC80211_LEDS ensures that it cannot be enabled manually when it
has no effect.
Fixes: 197f466e93 ("ath9k_htc: Do not select MAC80211_LEDS by default")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210125113654.2408057-1-arnd@kernel.org
Failed to transmit wmi management frames:
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
CPUx (skb_deuque) CPUy (__skb_queue_tail)
next=list
prev=list
struct sk_buff *skb = skb_peek(list); WRITE_ONCE(newsk->next, next);
WRITE_ONCE(list->qlen, list->qlen - 1);WRITE_ONCE(newsk->prev, prev);
next = skb->next; WRITE_ONCE(next->prev, newsk);
prev = skb->prev; WRITE_ONCE(prev->next, newsk);
skb->next = skb->prev = NULL; list->qlen++;
WRITE_ONCE(next->prev, prev);
WRITE_ONCE(prev->next, next);
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1.c2-00033-QCAHLSWMTPLZ-1
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608618887-8857-1-git-send-email-miaoqing@codeaurora.org
When connect to an AP with WPA mode, ath10k need to set need_ptk_4_way to
firmware in WMI_PEER_ASSOC_CMD, then the data path is disallow in
firmware, it will be allowed untill firmware finish the 4 way handshake.
It failed with a test case with below steps:
1. configure AP with WPA mode with ssid1 SimpleConnect_a_orbvt_ch1,
bssid1 and channel 1.
2. connect to ssid1 and ping success.
3. wait 10 seconds which is less than
IEEE80211_SCAN_RESULT_EXPIRE(30 seconds).
4. configure AP with OPEN mode with ssid2 SimpleConnect_b_z3a00_ch1,
but use same bssid1 and channel 1 of step 1.
5. disconnect ssid1.
6. connect to ssid2 and ping fail.
Fail reason:
When run step 6, ath10k_peer_assoc_h_crypto() called cfg80211_get_bss()
with bssid and chan info, but ssid1 and ssid2 have the same bssid and
channel, then there have 2 entry for ssid1 and ssid2 in cfg80211. The
ssid1's order is before ssid2 in bss_list, and ssid1's age is less than
the expire time which is IEEE80211_SCAN_RESULT_EXPIRE(30 seconds). Then
ssid1's entry is selected and ath10k_peer_assoc_h_crypto() parsed it and
get the rsnie and then need_ptk_4_way is set to firmware, so data path
is disallowed and it will not receive 4 way handshake for OPEN mode,
so ping fail in step 6.
This patch is to pass the ssid info to cfg80211_get_bss() as same as
cfg80211_mlme_assoc() and cfg80211_mlme_auth(), then it will find the
correct bss entry in above test case, then case success.
For AP mode, the ssid info is filled in ieee80211_start_ap(), for STATION
mode, it is filled in ieee80211_mgd_assoc(). Tested for both AP/STATION
mode with QCA6174 hw3.2 PCI, it is success start/connect/ping for
WPA/OPEN mode.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607312195-3583-3-git-send-email-wgong@codeaurora.org
ath10k assigns ath10k_mac_set_sar_specs to ath10k_ops, and
this function is called when user space application calls
NL80211_CMD_SET_SAR_SPECS. ath10k also registers SAR type,
and supported frequency ranges to wiphy so user space can
query SAR capabilities.
This SAR power limitation is compared to regulatory txpower
and selects the minimal one to set when station is connected.
Otherwise, it delays until the station is connected. If the
station is disconnected, it returns to regulatory txpower.
This feature is controlled by hw parameter: dynamic_sar_support.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201203103728.3034-4-cjhuang@codeaurora.org
memcpy operation is next to memset code, and the size to copy is equals to the size to
memset, so the memset operation is unnecessary, remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201223012516.24286-1-zhengyongjun3@huawei.com
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removed the duplicated peer related function declaration
from core.h since those functions are already declared in peer.h
Founded in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608304793-20612-1-git-send-email-periyasa@codeaurora.org
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200205191043.21913-1-linus.luessing@c0d3.blue
Function ep_rx_complete is being called without NULL checking
in ath10k_htc_rx_completion_handler. Without such check, mal-
formed packet is able to cause jump to NULL.
ep->service_id seems a good candidate for sanity check as it is
used in usb.c.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622022055.16028-1-bruceshenzk@gmail.com
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a970650 ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJf4h9uAAoJEG4XJFUm622byVMIAIwMhqVmDL7jqqOwd2xZa4jf
/QzAvx7tize/tBF6FubOpF+Bxzn4XaJzwFE97B0wwO6/rnxD2a56WUARuYF8ztnT
St18uYBU23n+QKfvL1qJI5Az0JXxia/cLDwvr8YPK3rmh2jmSOVyJSCUtHSJ+yQ2
hnJA3Af8ves3VpCZ2jqF7VcHM/xYfmoJZy3I7P6LpT5m+6FOqqdN8Mx6ei2aHEzY
+HHN26QoW35N2DCna+iTtEMpepWU8eoJmIOU+t881bRfZBoczc+WH99ZlSaVDUug
hl+Hy5bwDzN+HdGziSgWP6U5a+XNjRu6Y5dUpEm4YmL+uJeU4NPc0Q35nyx4RBM=
=fjHi
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.11
First set of fixes for v5.11, more fixes than usual this time. For
ath11k we have several fixes for QCA6390 PCI support and mt76 has
several. Also one build fix for mt76.
mt76
* fix two NULL pointer dereference
* fix build error when CONFIG_MAC80211_MESH is disabled
rtlwifi
* fix use-after-free in firmware handling code
ath11k
* error handling fixes
* fix crash found during connect and disconnect test
* handle HT disable better
* avoid printing qmi memory failure during firmware bootup
* disable ASPM during firmware bootup
* tag 'wireless-drivers-2020-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
MAINTAINERS: switch to different email address
mt76: mt7915: fix MESH ifdef block
mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
mt76: sdio: remove wake logic in mt76s_process_tx_queue
mt76: usb: remove wake logic in mt76u_status_worker
ath11k: pci: disable ASPM L0sLs before downloading firmware
ath11k: qmi: try to allocate a big block of DMA memory first
rtlwifi: rise completion at the last step of firmware callback
mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
ath11k: Fix ath11k_pci_fix_l1ss()
ath11k: Fix error code in ath11k_core_suspend()
ath11k: start vdev if a bss peer is already created
ath11k: fix crash caused by NULL rx_channel
ath11k: add missing null check on allocated skb
====================
Link: https://lore.kernel.org/r/20201222163727.D4336C433C6@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "&ar->ab->base_lock" and "&ab->base_lock" locks are the same lock
but it's nicer to use the same name consistently everywhere.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9s7QAHDM2OTIo3a@mwanda
Sometimes QCA6390 doesn't switch to amss state as device enters
L1ss state, so disable L0sL1s during firmware downloading.
Driver recovers the ASPM to default value in start callback
or powerdown callback.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608218530-15426-1-git-send-email-kvalo@codeaurora.org
Not all firmware versions support allocating DMA memory in smaller blocks so
first try to allocate big block of DMA memory for QMI. If the allocation fails,
let firmware request multiple blocks of DMA memory with smaller size.
This also fixes an unnecessary error message seen during ath11k probe on
QCA6390:
ath11k_pci 0000:06:00.0: Respond mem req failed, result: 1, err: 0
ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-22
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608127593-15192-1-git-send-email-kvalo@codeaurora.org
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-5-jouni@codeaurora.org
Now that ath/key.c may not be explicitly clearing keys from the key
cache, clear all key cache entries when disabling hardware to make sure
no keys are left behind beyond this point.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-3-jouni@codeaurora.org
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org
When the wlan is disabled, i.e when all the interfaces are
deleted, voltage regulator votes are not removed. This leads
to more power consumption even when wlan is disabled.
Move the adding/removing of voltage regulator votes as part
of hif power on/off in SNOC targets, so that these voltage
regulator votes are there only when wlan is enabled.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607713230-18382-1-git-send-email-pillair@codeaurora.org
Currently if the copy engine pipe init fails for snoc based
chipsets, the rri is not freed.
Fix this error handling for copy engine pipe init
failure.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 4945af5b26 ("ath10k: enable SRRI/DRRI support on ddr for WCN3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607713210-18320-1-git-send-email-pillair@codeaurora.org
All these conditions are reversed so presumably most of the function is
dead code. This caused a spurious warning:
[ 95.734922] ath11k_pci 0000:06:00.0: failed to set sysclk: 0
Fixes: 0699940755 ("ath11k: pci: fix L1ss clock unstable problem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9nGDHiTh+Z+asDy@mwanda
The "if (!ret)" condition is inverted and it should be "if (ret)". It means
that we return success when we had intended to return an error code. This also
caused a spurious warning even when the suspend was successful:
[ 297.186612] ath11k_pci 0000:06:00.0: failed to suspend hif: 0
Fixes: d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X9nF17L2/EKOSbn/@mwanda
For QCA6390, bss peer must be created before vdev is to start. This
change is to start vdev if a bss peer is created. Otherwise, ath11k
delays to start vdev.
This fixes an issue in a case where HT/VHT/HE settings change between
authentication and association, e.g., due to the user space request
to disable HT.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211051358.9191-1-cjhuang@codeaurora.org
Currently the null check on a newly allocated skb is missing and
this can lead to a null pointer dereference is the allocation fails.
Fix this by adding a null check and returning -ENOMEM.
Addresses-Coverity: ("Dereference null return")
Fixes: 43ed15e1ee ("ath11k: put hw to DBS using WMI_PDEV_SET_HW_MODE_CMDID")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214232417.84556-1-colin.king@canonical.com
Now that relay_open() accepts const callbacks, make relay callbacks
const.
Link: https://lkml.kernel.org/r/7db0286c428f3a478dd7544afef04a3b131f1aa0.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that relay_open() accepts const callbacks, make relay callbacks
const.
Link: https://lkml.kernel.org/r/44e3d65b71025c462948d0c554061dc7b40ab488.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that relay_open() accepts const callbacks, make relay callbacks const.
Link: https://lkml.kernel.org/r/85cabc6d4b0d0ca43d4e0fb94897ccd16e3b7930.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.
At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.
During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state. During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org
Add ce irq enable and disable hif layer functions, so core module can enable
enable them without cleaning pipe and refilling pipe. Needed for suspend.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-10-git-send-email-kvalo@codeaurora.org
Implement wow enable ane wow wakeup commands which are needed for suspend.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-9-git-send-email-kvalo@codeaurora.org
Firmware will check all the pipes before entering WoW mode during suspend. If
ATH11K_HTC_FLAG_NEED_CREDIT_UPDATE is set, firmware treats this pipe needed to
return credit even though it's actually not required. If any pipe needs to
return credit, the suspend_complete message doesn't send to host but is
dropped. So host gets time out and WoW suspend failed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-8-git-send-email-kvalo@codeaurora.org
Stop dp rx pktlog when entering suspend and reap the mon_status buffer to keep
it empty. During resume restart the reap timer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-7-git-send-email-kvalo@codeaurora.org
When ath11k sends suspend command to firmware, firmware will
return suspend_complete events and add handlers for those.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-6-git-send-email-kvalo@codeaurora.org
Just when resume from WoW, the write to select_window doesn't take
effect immediately, so read the register again to ensure the write
operation is finished.
Another change is to reset select_window to ZERO because this
register isn't restored after WoW, so the content of this register
becomes ZERO too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-4-git-send-email-kvalo@codeaurora.org
For suspend support add suspend and resume to HIF layer. These ops are optional
and, for example, AHB bus driver does not need to implement these.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-3-git-send-email-kvalo@codeaurora.org
MHI suspend and resume isn't hooked in ath11k yet, so hook these
functions needed for suspend support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-2-git-send-email-kvalo@codeaurora.org
Currently 6G specific tlvs have duplicate entries which is causing
scan failures. Fix this by removing the duplicate entries of the same
tlv. This also fixes out-of-bound memory writes caused due to
adding tlvs when num_hint_bssid and num_hint_s_ssid are ZEROs.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Fixes: 74601ecfef ("ath11k: Add support for 6g scan hint")
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-7-git-send-email-kvalo@codeaurora.org
It's recommended to disable VDD4BLOW during initialisation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-6-git-send-email-kvalo@codeaurora.org
For QCA6390, one PCI related clock drifts sometimes, and
it makes PCI link difficult to quit L1ss. Fix it by writing
some registers which are known to fix the problem.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-5-git-send-email-kvalo@codeaurora.org
For QCA6390, host needs to reset some registers before MHI power up to fix PCI
link unstable issue if hot reset happened. Also clear all pending interrupts
during power up.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-4-git-send-email-kvalo@codeaurora.org
It's recommended to use wmi command WMI_PDEV_SET_HW_MODE_CMDID to put hardware
to dbs mode instead of wmi_init command. This fixes a few strange stability
issues.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-3-git-send-email-kvalo@codeaurora.org
There was no way to detect if the firmware crashed so add a warning. At the
moment the firmware is not restarted or anything like that, so when this
happens ath11k modules need to be reloaded.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607609124-17250-2-git-send-email-kvalo@codeaurora.org
Use MHI provided APIs to allocate and free MHI controller to
improve MHI host driver handling. This also fixes a memory leak
as the MHI controller was allocated but never freed.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605634436-36506-1-git-send-email-bbhatt@codeaurora.org
When it has more than one restart_work queued meanwhile, the 2nd
restart_work is very easy to break the 1st restart work and lead
recovery fail.
Add a flag to allow only one restart work running untill
device successfully recovered.
It already has flag ATH10K_FLAG_CRASH_FLUSH, but it can not use this
flag again, because it is clear in ath10k_core_start. The function
ieee80211_reconfig(called by ieee80211_restart_work) of mac80211 do
many things and drv_start(call to ath10k_core_start) is 1st thing,
when drv_start complete, it does not mean restart complete. So it
add new flag and clear it in ath10k_reconfig_complete, because it
is the last thing called from drv_reconfig_complete of function
ieee80211_reconfig, after it, the restart process finished.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746bead6a0-d5e97c66-dedd-4b92-810e-c2e4840fafc9-000000@us-west-2.amazonses.com
In some devices difference in chip-id should be enough to pick
the right BDF. Add another support for chip-id based BDF selection.
With this new option, ath10k supports 2 fallback options.
The board name with chip-id as option looks as follows
board name 'bus=snoc,qmi-board-id=ff,qmi-chip-id=320'
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1
Tested-on: QCA6174 HW3.2 WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201207231824.v3.1.Ia6b95087ca566f77423f3802a78b946f7b593ff5@changeid
Assure that frames with the fixed order flag are not reordered
relative to each other. This is accomplished by transmitting them
using a fixed priority independent of their QoS field.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104061823.197407-6-Mathy.Vanhoef@kuleuven.be
Currently 256 bitmap in blockack frames is being set only for AP mode.
Fix this to set whenever beacon has changed and has HE capability, there
by supporting mesh as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-5-pradeepc@codeaurora.org
HE operation IE in beacons is constructed based on userspace params,
which firmware might not be aware of. This causes firmware not to
configure TXOP duration based RTS threshold which could cause mismatch
in behaviour with respect to what is being advertised in beacons. This
patch sends HE operation IE fetched from beacon to firmware using
WMI interface for configuration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-4-pradeepc@codeaurora.org
These error paths need to drop the &ar->conf_mutex before returning.
Fixes: 690ace20ff ("ath11k: peer delete synchronization with firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X85sVGVP/0XvlrEJ@mwanda
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f932c887e013767cbdabfdddd671086e8ae63193.1605896060.git.gustavoars@kernel.org
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
I am trying to get the ath11k driver to work with VyOS and during the
build it tries to discover the firmware blobs which drivers require.
This doesn't work with ath11k because it doesn't use the MODULE_FIRMWARE
macro. This patch fixes that.
Signed-off-by: Devin Bayer <dev@doubly.so>
[kvalo@codeaurora.org: cleanup commit log, move to pci.c]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201202182705.dhkml4nb4rf2vwav@orac
Incase of hardware encryption, WMI_PEER_AUTH flag will be set by firmware
during install key. Since install key wont be done for software encryption
mode, firmware will not set this flag. Due to this, seeing traffic failure
in software encryption. Hence, avoid resetting peer auth flag if hardware
encryption disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606369414-25211-1-git-send-email-seevalam@codeaurora.org
In QCN9074 ath11k boot, firmware crash is observed in 64-bit
builds and is due to wrong 64 bit MSI address size. This patch
fixes the firmware crash. Read msi high addr if 64-bit addresses
allowed on MSI.
Tested-On: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606199334-18206-1-git-send-email-akolli@codeaurora.org
cppcheck possible warnings: (new ones prefixed by >>, may not real problems)
drivers/net/wireless/ath/ath10k/sdio.c:2234:2:
warning: Non-boolean value returned from function returning bool [returnNonBoolInBooleanFunction]
return param & HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW;
Reported-by: kernel test robot <rong.a.chen@intel.com>
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606103240-9868-1-git-send-email-wgong@codeaurora.org
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfyTQyAAoJEG4XJFUm622bCdcIAIyVnqdW7pnoDmWIyQmAEnD9
vGARkzghPHXnufpOzohyDdxT12X9klhrxSVIgzEgH1/pl3i1PpnF6KXyGFCC44Lw
wrLXhQygPzmIW1IZtJJE3G72WExXoRjWx6LD1I7C7oEIduqFixXADmK2tKzFp795
Jxum+sOeT6+Dk1OvO/fIroBHX73mRE9zAuiTIMpt2G1j8uXs9QVfcTbTrUshLASN
0sX9J6JutltBuM4G7+bFpVzKnLnlQ7ebUaF6nvTCQsgHWZwkS7yAubSWX9sFohbR
UXgQHNE83s/esOg7nBxAfqTKP8mbxsobmxZtxE5GR5vFY5FJDxqP9Zc2KzPp39w=
=CbX/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.11
First set of patches for v5.11. rtw88 getting improvements to work
better with Bluetooth and other driver also getting some new features.
mhi-ath11k-immutable branch was pulled from mhi tree to avoid
conflicts with mhi tree.
Major changes:
rtw88
* major bluetooth co-existance improvements
wilc1000
* Wi-Fi Multimedia (WMM) support
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
* tag 'wireless-drivers-next-2020-12-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (180 commits)
wl1251: remove trailing semicolon in macro definition
airo: remove trailing semicolon in macro definition
wilc1000: added queue support for WMM
wilc1000: call complete() for failure in wilc_wlan_txq_add_cfg_pkt()
wilc1000: free resource in wilc_wlan_txq_add_mgmt_pkt() for failure path
wilc1000: free resource in wilc_wlan_txq_add_net_pkt() for failure path
wilc1000: added 'ndo_set_mac_address' callback support
brcmfmac: expose firmware config files through modinfo
wlcore: Switch to using the new API kobj_to_dev()
rtw88: coex: add feature to enhance HID coexistence performance
rtw88: coex: upgrade coexistence A2DP mechanism
rtw88: coex: add action for coexistence in hardware initial
rtw88: coex: add function to avoid cck lock
rtw88: coex: change the coexistence mechanism for WLAN connected
rtw88: coex: change the coexistence mechanism for HID
rtw88: coex: update AFH information while in free-run mode
rtw88: coex: update the mechanism for A2DP + PAN
rtw88: coex: add debug message
rtw88: coex: run coexistence when WLAN entering/leaving LPS
Revert "rtl8xxxu: Add Buffalo WI-U3-866D to list of supported devices"
...
====================
Link: https://lore.kernel.org/r/20201203185732.9CFA5C433ED@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ath.git patches for v5.11. Major changes:
ath11k
* Fast Initial Link Setup (FILS) discovery and unsolicited broadcast
probe response support
* qcom,ath11k-calibration-variant Device Tree setting
* cold boot calibration support
* new DFS region: JP
wnc36xx
* enable connection monitoring and keepalive in firmware
ath10k
* firmware IRAM recovery feature
mhi
* merge mhi-ath11k-immutable branch to make MHI API change go smoothly
This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.
This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org
qmi_msg_handler[] and ath10k_qmi_ops are only used as input arguments
to qmi_handle_init() which accepts const pointers to both qmi_ops and
qmi_msg_handler. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122234031.33432-3-rikard.falkeborn@gmail.com
Should an error occur after calling 'ath10k_usb_create()', it should be
undone by a corresponding 'ath10k_usb_destroy()' call
Fixes: 4db66499df ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170358.1346065-1-christophe.jaillet@wanadoo.fr
If 'ath10k_usb_create()' fails, we should release some resources and report
an error instead of silently continuing.
Fixes: 4db66499df ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170342.1346011-1-christophe.jaillet@wanadoo.fr
The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.
Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71
The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1
Fixes: cea19a6ce8 ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org
If 'kzalloc' fails, we must return an error code.
While at it, remove a useless initialization of 'err' which could hide the
issue.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122173943.1366167-1-christophe.jaillet@wanadoo.fr
It is rather easy to add more entries to ath11k_skb_cb while forgetting the
size limit of ieee80211_tx_info->driver_data. So just check this during the
build to reduce the change of accidental buffer overflow in the skbuff->cb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-3-sven@narfation.org
It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):
[ 86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
[ 86.963192] pgd = ffffffc0008f0000
[ 86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
[ 86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[...]
[ 87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
[ 87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
[ 87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
[ 87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
[ 87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
[ 87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
[ 87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
[ 87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
[ 87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
[ 87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)
Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
(162 patches at the moment which are often not upstreamed but essential
to get ath11k working)
Fixes: e7f33e0c52 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
Unused structure ath11k_vdev_stop_status is removed.
'ath11k_mac_get_ar_vdev_stop_status' api has been replaced
with 'ath11k_mac_get_ar_by_vdev_id' inside vdev_stopped_event.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-4-git-send-email-mkenna@codeaurora.org
Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org
When the interface is added immediately after removing the
interface, vdev deletion in firmware might not have been
completed.
Hence, add vdev_delete_resp_event and wait_event_timeout
to synchronize with firmware.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-2-git-send-email-mkenna@codeaurora.org
Set the rx_filter in ath11k_mac_config_mon_status_default(),
only when the rx_filter value exists in ath11k_debug_rx_filter().
Without this change, rx_filter gets set to 0 and peer rssi stats
aren't updating properly from firmware.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01230-QCAHKSWPL_SILICONZ-4
Fixes: ec48d28ba2 ("ath11k: Fix rx_filter flags setting for per peer rx_stats")
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605091117-11005-1-git-send-email-mkenna@codeaurora.org
This target IRAM recovery feature support is to copy target
IRAM contents available at ATH10K_MEM_REGION_TYPE_REG to host
memory for back up after firmware loaded. Target IRAM contents
are copied to wmi memory chunks allocated for the
WMI_IRAM_RECOVERY_HOST_MEM_REQ_ID and provide the wmi chunks
address to the firmware through wmi init command.
If firmware detects andy IRAM corruption through periodic
checksum validation, It will download the IRAM contents back
from the provided wmi memory chunks address using hif_memcpy.
This IRAM recovery feature prevent target assert in case of
unexpected target IRAM corruptions.
This patch also introduce a new feature flag 'iram-recovery' for
backward compatibility.
Tested-on: QCA9888 10.4-3.9.0.2-00094
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604657442-23674-1-git-send-email-vnaralas@codeaurora.org
STS Beamformee capability sent from firmware is overwritten as
num_tx_chains - 1.
When num_tx_chains is 2, then STS is set to invalid value 1.
Since STS is not limited by number of TX chain, not overwriting the
capability received from firmware.
Tested on: IPQ6018 WLAN.HK.2.4.0.1-00303-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <rgnanase@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604933229-15815-1-git-send-email-rgnanase@codeaurora.org
Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.
Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.
Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org
There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.
This is really up to the MHI device(channel) driver to manage the state
of its channels.
While at it, let's also remove the auto-start option from ath11k mhi
controller.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
ath11k_peer_create() is called without its return value being checked,
meaning errors will be unhandled. Add missing check and, as the mutex is
unconditionally unlocked on leaving this function, simplify the exit
path.
Addresses-Coverity-ID: 1497531 ("Code maintainability issues")
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-1-alex.dewar90@gmail.com
gcc-10 shows a false-positive warning with CONFIG_KASAN:
drivers/net/wireless/ath/ath9k/dynack.c: In function 'ath_dynack_sample_tx_ts':
include/linux/etherdevice.h:290:14: warning: writing 4 bytes into a region of size 0 [-Wstringop-overflow=]
290 | *(u32 *)dst = *(const u32 *)src;
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
Until gcc is fixed, work around this by using memcpy() in place
of ether_addr_copy(). Hopefully gcc-11 will not have this problem.
Link: https://godbolt.org/z/sab1MK
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97490
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[kvalo@codeaurora.org: remove ifdef and add a comment]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-8-arnd@kernel.org
Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.
This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Excess function parameter 'ptr' description in 'wmi_buffer_block'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-2-lee.jones@linaro.org
This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.
This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org
This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org
The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:
quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
FW doesn't receive acks for gLinkFailTxCnt number of packets, then
link will be disconnected."
The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.
Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.
In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.
Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083' wcn3680
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org
gcc -Wextra points out a type mismatch
drivers/net/wireless/ath/ath6kl/wmi.c: In function 'ath6kl_wmi_cmd_send':
drivers/net/wireless/ath/ath6kl/wmi.c:1825:19: warning: implicit conversion from 'enum <anonymous>' to 'enum wmi_data_hdr_data_type' [-Wenum-conversion]
1825 | false, false, 0, NULL, if_idx);
| ^~~~~
As far as I can tell, the numeric value is current here,
so just use the correct enum literal instead of 'false'.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-9-arnd@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'old' not described in 'ath_dynack_ewma'
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'new' not described in 'ath_dynack_ewma'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-40-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'rfBuf' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'reg32' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'numBits' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'firstBit' not described in 'ar5008_hw_phy_modify_rx_buffer'
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1734:18: warning: ‘ar9300PciePhy_clkreq_disable_L1_2p2’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1727:18: warning: ‘ar9300PciePhy_clkreq_enable_L1_2p2’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9485_initvals.h:1009:18: warning: ‘ar9485_fast_clock_1_1_baseband_postamble’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9340_initvals.h:624:18: warning: ‘ar9340Modes_ub124_tx_gain_table_1p0’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9330_1p1_initvals.h:1013:18: warning: ‘ar9331_common_tx_gain_offset1_1’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-11-lee.jones@linaro.org
There are only a couple of these and none of them are conformant.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pri_detector.c:39: warning: Function parameter or member 'head' not described in 'pulse_elem'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'val' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'fraction' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'tolerance' not described in 'pde_get_multiple'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/dfs_pattern_detector.c:34: warning: Function parameter or member 'region' not described in 'radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:141: warning: Function parameter or member 'region' not described in 'get_dfs_domain_radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'dpd' not described in 'channel_detector_get'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'freq' not described in 'channel_detector_get'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/regd.c:378: warning: Function parameter or member 'reg' not described in 'ath_reg_apply_ir_flags'
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-20-lee.jones@linaro.org
Japan has new Radar types as per latest regulatory,
included under MKK_N in FW. So adding new enum in
ath11k to support it.
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.4.0.1-00041-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604563475-5782-1-git-send-email-lavaks@codeaurora.org
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits
No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org
driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org
The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.
But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:
Invalid regulatory domain detected
------------[ cut here ]------------
WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
[...]
ath11k c000000.wifi1: failed to perform regd update : -22
The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.
Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org
The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.
The command can happen to look like
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00
instead of
0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org
cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.
caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.
This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.
The device tree requires an additional string to define the variant name
wifi@c000000 {
status = "okay";
qcom,ath11k-calibration-variant = "Cigtech-WF-188";
};
This would create the boarddata identifier for the board-2.bin search
* bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
Monitor ring Rx buffer is not really modified between dma map
and unmap. So remove the unnecssary data sync before dma unmap.
This does not fix any visible issue, found in code review.
Compile tested only.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602744454-22969-1-git-send-email-vthiagar@codeaurora.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-4-allen.lkml@gmail.com
The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org
This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.
Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org
The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.
Also, increment the variable i inline for clarity
Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com
In ath11k_mac_setup_iface_combinations(), if memory cannot be assigned
for the variable limits, then the memory assigned to combinations will
be leaked. Fix this.
Addresses-Coverity-ID: 1497534 ("Resource leaks")
Fixes: 2626c26970 ("ath11k: add interface_modes to hw_params")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-2-alex.dewar90@gmail.com
In bmps mode, beacons are filtered, and firmware is in charge
of monitoring the beacons and report changes or loss.
mac80211 must be advertised about such change to prevent it's
internal timer based beacon monitor to report beacon loss.
Fix that by setting/clearing the IEEE80211_VIF_BEACON_FILTER
vif flag on bmps entry/exit.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592471863-31402-2-git-send-email-loic.poulain@linaro.org
Host sends wmi command to allow hardware enter idle power
save mode in ath11k_mac_op_start function.
hw parameter idle_ps indicates whether idle power save is supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-8-git-send-email-kvalo@codeaurora.org
For QCA6390, Start a timer to update CE pipe 4 ring HP when shadow
register is enabled. Its' to avoid that HP isn't updated to target
register.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-7-git-send-email-kvalo@codeaurora.org
Start a timer to update REO HP if HP isn't updated to target.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-6-git-send-email-kvalo@codeaurora.org
The timer is to check if TCL HP isn't updated to target.
The timer will postpone itself if there are TX operations
during the interval, otherwise the timer handler updates
the HP again so the index value in HP register will be
forwarded to target register, and the timer stops afterwards.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-5-git-send-email-kvalo@codeaurora.org
For QCA6390, set wmi credit to 1 to avoid back-to-back write to
shadow register when shadow register is enabled.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-4-git-send-email-kvalo@codeaurora.org
To enable shadow register access, host needs to pass shadow
register configuration to firmware via qmi message. Host also
needs to update ring's HP or TP address to shadow register
address. The write operation to shadow register will be
forwarded to target register by hardware automatically, and
the write operation to shadow register is permitted even
when the target is in power save or sleep mode.
Update the shadow config whenever power up happens.
This feature is controlled by hw parameter supports_shadow_regs which is only
enabled for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org
For QCA6390, host can read and write registers below unwindowed
address directly without programming the window register. For
registers below bar0 + 4k - 32, host can read and write regardless
of the power save state. Shadow registers are located below
bar0 + 4K - 32.
Before MHI power up, there is no need to wakeup MHI so ini_done is
added to indicate it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-2-git-send-email-kvalo@codeaurora.org
Add packet log support for QCA6390, otherwise the data connection will stall
within a minute or so. Enable it via debugfs and use trace-cmd to capture the
pktlogs.
echo 0xffff 1 > /sys/kernel/debug/ath11k/qca6390\ hw2.0/mac0/pktlog_filter
The mon status ring doesn't support interrupt so far, so host starts
a timer to reap this ring. The timer handler also reaps the
rxdma_err_dst_ring in case of monitor mode.
As QCA6390 requires bss created ahead of starting vdev, so check
vdev_start_delay for monitor mode.
For QCA6390, it uses wbm_desc_rel_ring to return descriptors.
It also uses rx_refill_buf_ring to fill mon buffer instead of
rxdma_mon_buf_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601463073-12106-2-git-send-email-kvalo@codeaurora.org
QCA6390 does not support monitor mode at the moment so disable it altogether,
using a hack as mac80211 does not support disabling it otherwise. Add a boolean
to hw_params to know if hardware supports monitor mode.
IPQ8074 continues to support monitor mode normally.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-6-git-send-email-kvalo@codeaurora.org
There are different versions of QCA6390. Check TCSR_SOC_HW_VERSION to make sure
that the device is hw2.0, all the rest are unsupported.
This needs to be checked after ath11k_pci_claim() so move the whole switch choosing hw_ver.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-5-git-send-email-kvalo@codeaurora.org
As QCA6390 does not support mesh interfaces, move the interface_modes to
hw_params. Also create interface combinations dynamically so that it's easy to
change the values.
Now QCA6390 does not claim to support mesh interfaces to user space, but
IPQ8074 continues to do that.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-4-git-send-email-kvalo@codeaurora.org
For QCA6390, station vdev needs to delay startup but not for AP mode. On AP
mode vdev starts up immediately after bss peer is created in chanctx assignment
context.
This patch does not affect IPQ8074 family of devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-3-git-send-email-kvalo@codeaurora.org
The QCA6390 board I have, model 8291M-PR comes with an ELF board file. To get
this to at least somewhat work, I renamed bdwlan.e04 to 'board.bin' and then
added this patch to check for ELF magic string in the beginning of the file.
If that is found, use type ELF. After this the driver loads.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@codeaurora.org: use elf.h, minor cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601399736-3210-2-git-send-email-kvalo@codeaurora.org
debugfs_create_dir() returns an ERR_PTR in case of error, but never a
null pointer. There are a number of places where error-checking code can
accordingly be simplified.
Addresses-Coverity: CID 1497150: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497158: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497160: Memory - illegal accesses (USE_AFTER_FREE)
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200927132451.585473-1-alex.dewar90@gmail.com
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[876.898735] ath11k_pci 0000:06:00.0: Unknown eventid: 0x16005
[879.283250] ath11k_pci 0000:06:00.0: Unknown eventid: 0x1d00a
No functional changes. Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600948691-6901-1-git-send-email-govinds@codeaurora.org
This addresses the following gcc warning with "make W=1":
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1331:18: warning:
‘ar9580_1p0_pcie_phy_clkreq_enable_L1’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1338:18: warning:
‘ar9580_1p0_pcie_phy_clkreq_disable_L1’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9580_1p0_initvals.h:1345:18: warning:
‘ar9580_1p0_pcie_phy_pll_on_clkreq’ defined but not used [-Wunused-const-variable=]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600831531-8573-1-git-send-email-liheng40@huawei.com
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfbhn8AAoJEG4XJFUm622bFnMH/jI1Q+DXi2/sn3L01onNABqE
0M/HiZj/Gli2kYrIFiXKzCCVZBA/5CIZefh8Q+brsH4ZonJriTJ/VnJcGdDU68FK
ZqWSAkJ6+pJSaq7O/LofoTw+G0N64GPVN88ZqDMSoCyS8LDsE2QSjX6WEdeX7i9t
BWLcdXJ/brPzxtoH43c+w05syM+NCzPACUEKADa0KU5pg+MKHqtL/2FN8CecyU8k
ylzwH7w99mLBU3dDi8Q+EcUzOa0E+B7h56+BCcy/opCPZl0u2KGKcX/bRib1BwIB
wAChlEppwK/x8G8ViqxkrDVn1IiY2mnlFvdExuOlWqmVqwcccY8lEe19iAnzrV4=
=Xrmx
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild bot reported than link fails when CONFIG_ATH11K_DEBUGFS is disabled:
drivers/net/wireless/ath/ath11k/dp_rx.c:1662: undefined reference to `ath11k_debugfs_htt_ext_stats_handler'
This was because I had missed to move the static inline version of the function
(which are used when CONFIG_ATH11K_DEBUGFS is disabled) to debufs_htt_stats.h.
Also move ath11k_debugfs_htt_stats_req() at the same time. And create a stub
also for ath11k_debugfs_htt_stats_init() for consistency, even if it's not
needed.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 568f06036e ("ath11k: debugfs: move some function declarations to correct header files")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601024241-16594-1-git-send-email-kvalo@codeaurora.org
The "tsid" is a user controlled u8 which comes from debugfs. Values
more than 15 are invalid because "active_tsids" is a 16 bit variable.
If the value of "tsid" is more than 31 then that leads to a shift
wrapping bug.
Fixes: 8fffd9e5ec ("ath6kl: Implement support for QOS-enable and QOS-disable from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918142732.GA909725@mwanda
There were two asignments to num_keep_alive_pattern, remove the first one which is wrong.
No functional changes. Compile tested only.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600361190-22047-1-git-send-email-kvalo@codeaurora.org
In commit 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params") the
wmi config initialisation was moved to hw_ops->wmi_init_config() but the old
initialisation values were accidentally left to ath11k_wmi_cmd_init(). This
is very confusing, so remove the redundant values.
And this was actually so confusing that in commit aa2092a9ba ("ath11k: add
raw mode and software crypto support") I actually it caused a bug: when
ATH11K_FLAG_RAW_MODE was enabled rx_decap_mode was assigned back to
TARGET_DECAP_MODE_NATIVE_WIFI in ath11k_init_wmi_config_ipq8074(). Fix this at
the same time.
Compile tested only.
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600356507-29237-1-git-send-email-kvalo@codeaurora.org
IPQ6018 supported with 4 bytes FFT BIN size. so supported 4 bytes
parsing logic in FFT report process. since spectral_fft_sz is
configured as zero in hw_params, spectral is not supported in
QCA6390 platform.
Tested-on: IPQ6018 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600236776-4042-1-git-send-email-periyasa@codeaurora.org
Some of the function declarations are for functions in debugfs_htt_stats.c and
debugfs_sta.c, move them to corresponding header files. As debugfs_sta.h didn't
exist create it.
Also in debugfs_htt_stats.h move dunction declarations to the end of the file.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-4-git-send-email-kvalo@codeaurora.org
If CONFIG_ATH11K_DEBUGFS is disabled there are warnings debug.c:
drivers/net/wireless/ath/ath11k/debug.c:36:20: warning: 'htt_bp_lmac_ring' defined but not used [-Wunused-variable]
36 | static const char *htt_bp_lmac_ring[HTT_SW_LMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/debug.c:15:20: warning: 'htt_bp_umac_ring' defined but not used [-Wunused-variable]
15 | static const char *htt_bp_umac_ring[HTT_SW_UMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
Fix this by refactoring debugfs code to debugfs.c. This also reduces the number
of ifdefs in debug.c and makes it easier to maintain the code.
No functional changes. Compile tested only.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-1-git-send-email-kvalo@codeaurora.org
Return value form wait_for_completion_timeout should to be checked.
This is detected by Coverity: #CID:1464479 (CHECKED_RETURN)
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200621095136.7xdbzkthoxuw2qow@debian.debian-2
This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
This patch adds ieee802.11 VHT flags for the wcn3680b.
- RX_STBC1
- SU Beamformee
- MU Beamformee
- VHT80 SGI
- Single spatial stream
RX LDPC is declared as supported in the datasheet but not enabled at this
time.
After this patch is applied an AP should see the wcn3680 as an 802.11ac
capable device.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-5-bryan.odonoghue@linaro.org
This commit adds VHT rates to the wcn36xx_update_allowed_rates() routine.
Thus allowing the driver to latch the declared rates and transmit them to
the firmware in the same way as other 80211.n rates are.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-4-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
In order to get 802.11ac working the way we want, additional parameters
need to be passed down to the firmware.
This patch takes the full remaining set of parameters defined in the
downstream riva/inc/wlan_hal_cfg.h and imports them into hal.h with some
minor name length adjustments.
This addition will allow us to pass a larger firmware configuration set
later on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-2-bryan.odonoghue@linaro.org
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
This commit encodes the 802.11ac PHY mode for a given channel in the upper
bits of the hw_value field. This allows for a neat read-out and application
of the relevant PHY setting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-5-bryan.odonoghue@linaro.org
Adds HW_VALUE_PHY(hw_value) an access macro that will be used to
extract a hardware specific PHY setting for a given channel.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-4-bryan.odonoghue@linaro.org
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
Adds HW_VALUE_CHANNEL(hw_value) an access macro that will be used to
extract the channel number from struct ieee80211_channel->hw_value in
preparation for also storing PHY settings for 802.11ac in the upper bits of
hw_value.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-2-bryan.odonoghue@linaro.org
Board Data File (BDF) is loaded upon driver boot-up procedure.
The right board data file is identified using bus and qmi-board-id.
The problem, however, can occur when the (default) board data
file cannot fulfill with the vendor requirements and it is
necessary to use a different board data file.
Also using the chip_id for identifying the board data helps
in dealing with different variants of the board data file based
on the RF card. If the chip_id is not programmed, a default value
of 0xff will be used for parsing the board data file.
Add the support to get the variant field from DTSI and
use this information along with the chip_id to load the vendor
specific BDF.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v2";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "xyz-v1";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=snoc,qmi-board-id=16,qmi-chip-id=0,variant=xyz-v1
* bus=snoc,qmi-board-id=17,qmi-chip-id=0,variant=xyz-v2
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600157948-2042-1-git-send-email-pillair@codeaurora.org
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been
designed to operate in standalone fashion. As a result we can drop the
dead code now present in wcn36xx_smd_config_bss() and happily remove one
kzalloc from the BSS config path as we do so.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-8-bryan.odonoghue@linaro.org
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the
version 0 data-path in wcn36xx_smd_config_bss() to use
wcn36xx_smd_config_bss_v0().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-7-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of
functionally decomposing wcn36xx_smd_config_bss().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-6-bryan.odonoghue@linaro.org
This patch updates wcn36xx_smd_config_bss_v1() to update on internally
derived parameters only, specifically making use of STA v1 wrapper routines
previously added.
Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg
which gives us options in later patches to eliminate the kzalloc() in
wcn36xx_smd_config_bss entirely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-5-bryan.odonoghue@linaro.org
This commit moves BSS parameter setup to a separate function
wcn36xx_smd_set_bss_params(). This will allow for further functional
decomposition and fewer kzalloc() operations in subsequent patches.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-4-bryan.odonoghue@linaro.org
In order to facilitate functional decomposition of
wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later
in function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-3-bryan.odonoghue@linaro.org
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly
defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-2-bryan.odonoghue@linaro.org
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which
calls into wcn36xx_smd_set_sta_params() and then subsequently sets
version-1 specific parameters.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-8-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function
is to decide if the BSS is VHT capable and if so set the appropriate bit
in the BSS parameter structure for passing to the firmware.
VHT Channel width set is not set since we don't support 160MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-7-bryan.odonoghue@linaro.org
Adds a routine to allow setting the LDPC bit for HT parameter passing
inside the version 1 STA parameters data structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-6-bryan.odonoghue@linaro.org
This commit adds support for setting VHT parameters based on the declared
VHT capability bits in the VHT capability structure.
We cannot do 160MHz so VHT Channel width set should be zero.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-5-bryan.odonoghue@linaro.org
Toggling the LDPC enabled bit is possible only via the extended V1
data-structure. This function provides a means of setting the default
depending on chip-type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-4-bryan.odonoghue@linaro.org
This commit adds support for setting default VHT parameters, which are
exposed by the extended version 1 STA parameter type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-3-bryan.odonoghue@linaro.org
This patch converts the internal data structure used to store data-rates
from version 0 to version 1.
This allows us to extend out the internal storage to represent VHT
parameters.
Using the extended version 1 data-structure allows us to avoid a whole raft
of version 1 specific fixup functions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-3-bryan.odonoghue@linaro.org
In order to pass VHT parameters to wcn3680 we need to use a super-set of
the V1 data-structures with additional VHT parameters tacked on.
This patch adds the additional fields to the STA and BSS parameter
structures.
Since neither wcn3620 nor wcn3660 support VHT the size of the passed
message is fixed to the previous message length. Subsequent changes will
differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger
message size.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-2-bryan.odonoghue@linaro.org
IPQ8074 HW uses rproc with AHB as underlying hif layer.
Move rproc references from common core layer to target
hif layer. Remove IS_ENABLED check for CONFIG_REMOTEPROC
as it's not required anymore.
No functional changes. Compile tested only.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600090615-18904-1-git-send-email-govinds@codeaurora.org
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfW5XtAAoJEG4XJFUm622bnuoIAIx8xplr5UYZv/qaMyvBaoNQ
gG7AU3IUs4QibSUabpE7kBpdLVX9O4mC5nLWCutGH1dTrJGIQsnuncW206yOAZPp
+MPOauxBmfkBm61RmJ3beGXan6ZGlE7rwkO0Pf+mqrWk4XVovItKpJUuR+IWliu/
gdVbdC2Uu7bQlv44MI/3xOpx5Xvk5gq/4tPcTOE3b57wIyln0NSKJYOoOuL+i2f/
WDiTgPyA/9x+llrf6sA+oLmEN2F8TpVWSDv6F4mA5E9uYjJrJMEJLosSzohU7+ou
j7gvCMv5F8+XnQYX4T/qJ05axBDQO2zRJ6YynWDoqQss4XW8xaiuQCEmaiHE8GM=
=kS8U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.
To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0
To enable software crypto:
insmod ath11k.ko crypto_mode=1
These modes could be helpful in debugging crypto related issues.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com
Add peer max mpdu length configuration support in peer_assoc_he
parameters. Noticed low throughput for the STA which
supports HE, HT and not VHT in MU-MIMO case without this
configuration
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588611900-21185-2-git-send-email-tamizhr@codeaurora.org
There is a success path where "ret" isn't initialized where we never
have a ATH11K_SPECTRAL_TAG_SCAN_SEARCH and then ret isn't initialized.
Fixes: 9d11b7bff9 ("ath11k: add support for spectral scan")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200619142922.GA267142@mwanda
clang static analyzer reports this problem
mac.c:6204:2: warning: Attempt to free released memory
kfree(ar->mac.sbands[NL80211_BAND_2GHZ].channels);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The channels pointer is allocated in ath11k_mac_setup_channels_rates()
When it fails midway, it cleans up the memory it has already allocated.
So the error handling needs to skip freeing the memory.
There is a second problem.
ath11k_mac_setup_channels_rates(), allocates 3 channels. err_free
misses releasing ar->mac.sbands[NL80211_BAND_6GHZ].channels
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906212625.17059-1-trix@redhat.com
Add support to vote for chain-1 voltage regulator
in WCN3990.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593194502-13164-3-git-send-email-pillair@codeaurora.org
In order for the firmware to process extended V1 parameters with the
addtional VHT fields added we need to first enable the feature bit DOT11AC.
Once done the version number in the HAL message header will be acted upon
by the firmware.
Extended V1 parameters are a prerequisite for 802.11ac speeds since we
cannot communicate VHT parameters to the firmware absent the extended data
structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-11-bryan.odonoghue@linaro.org
Two pointers are already defined in this function "bss" and "sta" which
point to fields within msg_body->bss_params.
We can substantially reduce the amount of extraneous text in this function
by making use of those pointers. This change makes the code easier to read
and modify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-10-bryan.odonoghue@linaro.org
Specify the number of spatial streams in ieee80211_rx_status. For non VHT
data-rates the wireless core doesn't care about this field, however for VHT
data-rates it does.
Every version of wcn36xx has one spatial stream, so specify nss for
wcn3620, wcn3660 and wcn3680 now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-7-bryan.odonoghue@linaro.org
The rate_idx is the index of the bitrate in the supported rate table.
However the 5Ghz band has a smaller legacy bitrate table than 2.4Ghz
since it does not have the DSSS bitrates (1, 2, 5.5, 11).
So in 5Ghz band the index should adjusted accrodingly (-4).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[bod: Made sure fix is only applied if the rate_idx > n_bitrates]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-6-bryan.odonoghue@linaro.org
If DT indicates we are dealing with a WCN3680 mark the rf_id field as
RF_IRIS_WCN3680 allowing for further chip-specific logic.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-3-bryan.odonoghue@linaro.org
The WCN3680 has some specific behaviours that we want to capture to
distinguish it from the WCN3620 and WCN3660 respectively.
Add an identifier for this purpose.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-2-bryan.odonoghue@linaro.org
As of the patch ("ath10k: Keep track of which interrupts fired, don't
poll them") we now have no users of this hardware parameter. Remove
it.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200709082024.v2.2.I083faa4e62e69f863311c89ae5eb28ec5a229b70@changeid
If we have a per CE (Copy Engine) IRQ then we have no summary
register. Right now the code generates a summary register by
iterating over all copy engines and seeing if they have an interrupt
pending.
This has a problem. Specifically if _none_ if the Copy Engines have
an interrupt pending then they might go into low power mode and
reading from their address space will cause a full system crash. This
was seen to happen when two interrupts went off at nearly the same
time. Both were handled by a single call of ath10k_snoc_napi_poll()
but, because there were two interrupts handled and thus two calls to
napi_schedule() there was still a second call to
ath10k_snoc_napi_poll() which ran with no interrupts pending.
Instead of iterating over all the copy engines, let's just keep track
of the IRQs that fire. Then we can effectively generate our own
summary without ever needing to read the Copy Engines.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200709082024.v2.1.I4d2f85ffa06f38532631e864a3125691ef5ffe06@changeid
Currently the NAPI processing loops through all
the copy engines and processes a particular copy
engine is the copy completion is set for that copy
engine. The host driver is not supposed to access
any copy engine register after clearing the interrupt
status register.
This might result in kernel crash like the one below
[ 1159.220143] Call trace:
[ 1159.220170] ath10k_snoc_read32+0x20/0x40 [ath10k_snoc]
[ 1159.220193] ath10k_ce_per_engine_service_any+0x78/0x130 [ath10k_core]
[ 1159.220203] ath10k_snoc_napi_poll+0x38/0x8c [ath10k_snoc]
[ 1159.220270] net_rx_action+0x100/0x3b0
[ 1159.220312] __do_softirq+0x164/0x30c
[ 1159.220345] run_ksoftirqd+0x2c/0x64
[ 1159.220380] smpboot_thread_fn+0x1b0/0x288
[ 1159.220405] kthread+0x11c/0x12c
[ 1159.220423] ret_from_fork+0x10/0x18
To avoid such a scenario, we generate an interrupt
summary by reading the copy completion for all the
copy engine before actually processing any of them.
This will avoid reading the interrupt status register
for any CE after the interrupt status is cleared.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593193967-29897-1-git-send-email-pillair@codeaurora.org
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
variable _len_.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616225132.GA19873@embeddedor
'ar9170_qmap' is used in some source files which include carl9170.h,
but not all of them. A 'defined but not used' warning is thrown when
compiling the ones which do not use it.
Fixes the following W=1 kernel build warning(s)
from drivers/net/wireless/ath/carl9170/carl9170.h:57,
In file included from drivers/net/wireless/ath/carl9170/carl9170.h:57,
drivers/net/wireless/ath/carl9170/carl9170.h:71:17: warning: ‘ar9170_qmap’ defined but not used [-Wunused-const-variable=]
NB: Snipped - lots of these repeat
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827093351.GA1627017@dell
There has been no attempt to document any of the function parameters here.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'dev' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'ops' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'rops' not described in 'wil_platform_init'
drivers/net/wireless/ath/wil6210/wil_platform.c:27: warning: Function parameter or member 'wil_handle' not described in 'wil_platform_init'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073832.GW3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'wil' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'num_descriptors' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:43: warning: Function parameter or member 'descriptor_size' not described in 'wil_pmc_alloc'
drivers/net/wireless/ath/wil6210/pmc.c:229: warning: Function parameter or member 'wil' not described in 'wil_pmc_free'
drivers/net/wireless/ath/wil6210/pmc.c:229: warning: Function parameter or member 'send_pmc_cmd' not described in 'wil_pmc_free'
drivers/net/wireless/ath/wil6210/pmc.c:307: warning: Function parameter or member 'wil' not described in 'wil_pmc_last_cmd_status'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'filp' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'buf' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'count' not described in 'wil_pmc_read'
drivers/net/wireless/ath/wil6210/pmc.c:320: warning: Function parameter or member 'f_pos' not described in 'wil_pmc_read'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073718.GV3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'wil' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'ring' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:155: warning: Function parameter or member 'i' not described in 'wil_ring_alloc_skb_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'wil' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1161: warning: Function parameter or member 'sring' not described in 'wil_tx_sring_handler'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tso_desc_type' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'is_ipv4' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'tcp_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'skb_net_hdr_len' not described in 'wil_tx_desc_offload_setup_tso_edma'
drivers/net/wireless/ath/wil6210/txrx_edma.c:1328: warning: Function parameter or member 'mss' not described in 'wil_tx_desc_offload_setup_tso_edma'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073545.GU3248864@dell
None of these headers provide any parameter documentation.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'wil' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'vring' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'i' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:259: warning: Function parameter or member 'headroom' not described in 'wil_vring_alloc_skb'
drivers/net/wireless/ath/wil6210/txrx.c:309: warning: Function parameter or member 'wil' not described in 'wil_rx_add_radiotap_header'
drivers/net/wireless/ath/wil6210/txrx.c:309: warning: Function parameter or member 'skb' not described in 'wil_rx_add_radiotap_header'
drivers/net/wireless/ath/wil6210/txrx.c:444: warning: Function parameter or member 'wil' not described in 'wil_vring_reap_rx'
drivers/net/wireless/ath/wil6210/txrx.c:444: warning: Function parameter or member 'vring' not described in 'wil_vring_reap_rx'
drivers/net/wireless/ath/wil6210/txrx.c:610: warning: Function parameter or member 'wil' not described in 'wil_rx_refill'
drivers/net/wireless/ath/wil6210/txrx.c:610: warning: Function parameter or member 'count' not described in 'wil_rx_refill'
drivers/net/wireless/ath/wil6210/txrx.c:1011: warning: Function parameter or member 'wil' not described in 'wil_rx_handle'
drivers/net/wireless/ath/wil6210/txrx.c:1011: warning: Function parameter or member 'quota' not described in 'wil_rx_handle'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'skb' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'tso_desc_type' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'is_ipv4' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'tcp_hdr_len' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1643: warning: Function parameter or member 'skb_net_hdr_len' not described in 'wil_tx_desc_offload_setup_tso'
drivers/net/wireless/ath/wil6210/txrx.c:1674: warning: Function parameter or member 'd' not described in 'wil_tx_desc_offload_setup'
drivers/net/wireless/ath/wil6210/txrx.c:1674: warning: Function parameter or member 'skb' not described in 'wil_tx_desc_offload_setup'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'wil' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'vif' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'ring' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2240: warning: Function parameter or member 'check_stop' not described in '__wil_update_net_queues'
drivers/net/wireless/ath/wil6210/txrx.c:2430: warning: Function parameter or member 'vif' not described in 'wil_tx_complete'
drivers/net/wireless/ath/wil6210/txrx.c:2430: warning: Function parameter or member 'ringid' not described in 'wil_tx_complete'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073442.GT3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/interrupt.c:652: warning: Function parameter or member 'irq' not described in 'wil6210_thread_irq'
drivers/net/wireless/ath/wil6210/interrupt.c:652: warning: Function parameter or member 'cookie' not described in 'wil6210_thread_irq'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073338.GS3248864@dell
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/wmi.c:52: warning: Incorrect use of kernel-doc format: * Addressing - theory of operations
drivers/net/wireless/ath/wil6210/wmi.c:70: warning: Incorrect use of kernel-doc format: * @sparrow_fw_mapping provides memory remapping table for sparrow
drivers/net/wireless/ath/wil6210/wmi.c:80: warning: cannot understand function prototype: 'const struct fw_map sparrow_fw_mapping[] = '
drivers/net/wireless/ath/wil6210/wmi.c:107: warning: Cannot understand * @sparrow_d0_mac_rgf_ext - mac_rgf_ext section for Sparrow D0
drivers/net/wireless/ath/wil6210/wmi.c:115: warning: Cannot understand * @talyn_fw_mapping provides memory remapping table for Talyn
drivers/net/wireless/ath/wil6210/wmi.c:158: warning: Cannot understand * @talyn_mb_fw_mapping provides memory remapping table for Talyn-MB
drivers/net/wireless/ath/wil6210/wmi.c:236: warning: Function parameter or member 'x' not described in 'wmi_addr_remap'
drivers/net/wireless/ath/wil6210/wmi.c:255: warning: Function parameter or member 'section' not described in 'wil_find_fw_mapping'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'wil' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:278: warning: Function parameter or member 'size' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:307: warning: Function parameter or member 'wil' not described in 'wmi_addr'
drivers/net/wireless/ath/wil6210/wmi.c:307: warning: Function parameter or member 'ptr' not described in 'wmi_addr'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'wil' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'vif' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'cid' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1589: warning: Function parameter or member 'ringid' not described in 'wil_find_cid_ringid_sta'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'vif' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'id' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'd' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:1876: warning: Function parameter or member 'len' not described in 'wmi_evt_ignore'
drivers/net/wireless/ath/wil6210/wmi.c:2588: warning: Function parameter or member 'wil' not described in 'wmi_rxon'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200827073201.GR3248864@dell
The return error check on the call to ath11k_pci_get_user_msi_assignment is
missing. If an error does occur, num_vectors is still set to zero and
later on a division by zero can occur when variable vector is being
calculated. Fix this by adding an error check after the call.
Addresses-Coverity: ("Division or modulo by zero")
Fixes: d4ecb90b38 ("ath11k: enable DP interrupt setup for QCA6390")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819111452.52419-1-colin.king@canonical.com
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-5-allen.cryptic@gmail.com
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-4-allen.cryptic@gmail.com
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'wil' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'dbg' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'base' not described in 'wil6210_debugfs_init_offset'
drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'tbl' not described in 'wil6210_debugfs_init_offset'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200819072402.3085022-22-lee.jones@linaro.org
Returning PTR_ERR(NULL) means success, but we should return -ENOMEM.
Fixes: 1399fb87ea ("ath11k: register MHI controller device for QCA6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826113417.GE393664@mwanda
In ath11k_qmi_prepare_bdf_download(), ath11k_core_firmware_request() is
called, but the returned pointer is not checked for errors. Rather the
variable ret (which will always be zero) is checked by mistake. Fix
this and replace the various gotos with simple returns for clarity.
While we are at it, move the call to memset, as variable bd is not used
on all code paths.
Fixes: 7b57b2ddec ("ath11k: create a common function to request all firmware files")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200825143040.233619-1-alex.dewar90@gmail.com
The ath9k driver hides all LEDs related code behind CONFIG_MAC80211_LEDS
ifdefs so it does not really require the MAC80211_LEDS. The code builds
fine. Convert the "select" into "imply" to allow disabling LED trigger
when not needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820194049.28055-1-krzk@kernel.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:627:18: warning: ‘ar5416Bank7’ defined but not used [-Wunused-const-variable=]
627 | static const u32 ar5416Bank7[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:548:18: warning: ‘ar5416Bank3’ defined but not used [-Wunused-const-variable=]
548 | static const u32 ar5416Bank3[][3] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:542:18: warning: ‘ar5416Bank2’ defined but not used [-Wunused-const-variable=]
542 | static const u32 ar5416Bank2[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:536:18: warning: ‘ar5416Bank1’ defined but not used [-Wunused-const-variable=]
536 | static const u32 ar5416Bank1[][2] = {
| ^~~~~~~~~~~
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:462:18: warning: ‘ar5416Bank0’ defined but not used [-Wunused-const-variable=]
462 | static const u32 ar5416Bank0[][2] = {
| ^~~~~~~~~~~
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-27-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar5008_initvals.h:553:18: warning: ‘ar5416Bank6’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-26-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9001_initvals.h:462:18: warning: ‘ar5416Bank6_9100’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-19-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath9k/ar9002_initvals.h:900:18: warning: ‘ar9280PciePhy_clkreq_off_L1_9280’ defined but not used [-Wunused-const-variable=]
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-18-lee.jones@linaro.org
The ath9k_htc driver hides all LEDs related code behind
CONFIG_MAC80211_LEDS ifdefs so it does not really require the
MAC80211_LEDS. The code builds and works just fine. Convert the
"select" into "imply" to allow disabling LED trigger when not needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820120444.8809-1-krzk@kernel.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-3-allen.cryptic@gmail.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath6kl/wmi.c: In function ‘ath6kl_wmi_bitrate_reply_rx’:
drivers/net/wireless/ath/ath6kl/wmi.c:1204:6: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200826093401.1458456-15-lee.jones@linaro.org
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200817090637.26887-2-allen.cryptic@gmail.com
For whatever reason, when connected to an open/no-security BSS,
the wcn36xx controller in bmps mode does not forward 'wake-up'
beacons despite AP sends DTIM with station AID.
Meaning that AP is not able to wakeup the station and needs to wait
for the station to wakeup by its own (TX data, keep alive pkt...),
causing serious latency issues and unexpected deauth.
When connected to AP with encryption enabled, this issue does not occur.
So a simple workaround is to only enable bmps support in that case.
Ideally, it should be propertly fixed to allow bmps support with open
BSS, whatever the issue is at driver or firmware level.
Tested on wcn3620 and wcn3680.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598363127-26066-1-git-send-email-loic.poulain@linaro.org
By default, after associated to an AP, the wcn36xx bitrate adjustment
algorithm starts sending data at 1Mbps, and increases the rate slowly
(1Mbps, 2Mbps, 6Mbps...) over the further TX packets.
Starting at 1Mbps usually causes the initial throughput to be really
low and the maximum possible bitrate to be reached after about hundreed
of TX packets.
That can be improved by setting a different initial bitrate for data
packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this
value can be a legacy or MCS rate.
This patch sets the starting bitrate value to MCS-5, which seems to be
a good compromise given it can be quickly adjusted low or up if necessary.
(and based on what I observed in the wild with some mobile devices)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598345341-4505-1-git-send-email-loic.poulain@linaro.org
For software-driven scan, rely on mac80211 software scan instead
of internal driver implementation. The internal implementation
cause connection trouble since it keep the antenna busy during
the entire scan duration, moreover it's only a passive scanning
(no probe request). Therefore, let mac80211 manages sw scan.
Note: we fallback to software scan if firmware does not report
scan offload support or if we need to scan the 5Ghz band (currently
not supported by the offload scan...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
The only usage of ath11k_thermal_ops is to pass its address to
thermal_cooling_device_register() which takes a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ops for reset_tid_config to support reset TID
configuration. This send default configuration to the
target for the TIDs and stores default value in the host.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-5-git-send-email-tamizhr@codeaurora.org
This patch add ops for set_tid_config to support TID
specific configuration. Station specific TID configuration
will have more priority than vif specific TID configuration.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT service flag introduced
to notify host for TID config support. And RTS_CTS extended tid
configuration support advertised through the service flag
WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT.
TID specific noack configuration requires
aggregation should be disabled and rate for the data TID packets
should be basic rates. So, if the TID already configured
with noack policy then driver will ignore the aggregation
or TX rate related configuration for the same data TID.
In TX rate configuration should be applied with highest
preamble configuration(HT rates should not be applied
for the station which supports vht rates).
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-4-git-send-email-tamizhr@codeaurora.org
This patch adds WMI interface to configure station specific
TID configuration . Host needs to send station's MAC address
along with TID number and its configuration to target through
WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID.
WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT flag is added to advertise
this support.
Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593875614-5683-2-git-send-email-tamizhr@codeaurora.org
When firmware crashes it's possible to create a coredump for later analysis,
add support to collect the register and memory info from SDIO devices.
The coredump configuration is different between QCA6174 PCI and QCA6174 SDIO,
so add specific registers and memory regions for the latter.
QCA6174 SDIO has two methods to dump the firmware: fastdump and slowdump.
Fastdump is not supported in olded versions of firmware, and for these ath10k
will automatically select slowdump. If firmware supports fastdump, ath10k will
automatically select it. QCA6174 SDIO firmware version
WLAN.RMH.4.4.1-00017-QCARMSWPZ-2 is the first version supporting fastdump.
For slowdump, ath10k_sdio_hif_diag_read() can not be used as the diag
window has a limit value, it is 4 bytes and the dump's buffer length is larger
than it, it will trigger error. So this patch adds ath10k_sdio_read_mem() to
read 4 bytes for each time.
Example output of a firmware crash:
ath10k_sdio mmc1:0001:1: simulating soft firmware crash
ath10k_sdio mmc1:0001:1: firmware crashed! (guid 413d98b1-84c0-4298-b605-2b10ec0c54a5)
ath10k_sdio mmc1:0001:1: qca6174 hw3.2 sdio target 0x05030000 chip_id 0x00000000 sub 0000:0000
ath10k_sdio mmc1:0001:1: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 1
ath10k_sdio mmc1:0001:1: firmware ver WLAN.RMH4.4.1-00126-QCARMSWP-1 api 6 features wowlan,ignore-otp,raw-mode crc32 b84317cf
ath10k_sdio mmc1:0001:1: board_file api 2 bmi_id 0:4 crc32 6364cfcc
ath10k_sdio mmc1:0001:1: htt-ver 3.69 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
ath10k_sdio mmc1:0001:1: firmware register dump:
ath10k_sdio mmc1:0001:1: [00]: 0x05030000 0x000015B3 0x0099908D 0x00955B31
ath10k_sdio mmc1:0001:1: [04]: 0x0099908D 0x00060730 0x00000018 0x004641A0
ath10k_sdio mmc1:0001:1: [08]: 0x0041FAA4 0x0041FA9C 0x00999070 0x00404490
ath10k_sdio mmc1:0001:1: [12]: 0x00000009 0xFFFFFFFF 0x00952CD0 0x00952CE6
ath10k_sdio mmc1:0001:1: [16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [20]: 0x4099908D 0x0040E9E8 0x00000001 0x00423AC0
ath10k_sdio mmc1:0001:1: [24]: 0x809F3189 0x0040EA48 0x00426240 0xC099908D
ath10k_sdio mmc1:0001:1: [28]: 0x809143A7 0x0040EA68 0x0041FAA4 0x00423A80
ath10k_sdio mmc1:0001:1: [32]: 0x809F1193 0x0040EA88 0x00411770 0x004117E0
ath10k_sdio mmc1:0001:1: [36]: 0x809F0EEE 0x0040EAA8 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [40]: 0x80911210 0x0040EAC8 0x00000008 0x00404130
ath10k_sdio mmc1:0001:1: [44]: 0x80911154 0x0040EB28 0x00400000 0x00000000
ath10k_sdio mmc1:0001:1: [48]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
ath10k_sdio mmc1:0001:1: [52]: 0x40910024 0x0040EB78 0x0040AB98 0x0040AB98
ath10k_sdio mmc1:0001:1: [56]: 0x00000000 0x0040EB98 0x009BB001 0x00040020
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-3-git-send-email-wgong@codeaurora.org
For some hw version, it has more than one bus type, it need to add bus
type to distinguish different chip.
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-2-git-send-email-wgong@codeaurora.org
ath.git patches for v5.10. Major changes:
ath11k
* add support for QCA6390 PCI devices
wcn36xx
* add support for TX ack
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
When STBC is enabled, NSTS_SU value need to be accounted for VHT NSS
calculation for SU case.
Without this fix, 1SS + STBC enabled case was reported wrongly as 2SS
in radiotap header on monitor mode capture.
Tested-on: QCA9984 10.4-3.10-00047
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392971-3897-1-git-send-email-murugana@codeaurora.org
As a part of device shutdown the smmu driver will be
stopped and henceforth any IOVA address translation
will not be done. The wlan driver, being one of the
smmu driver consumer, should stop all the dma related
activity as a part of shutdown, and thereby ensuring
that no dma activity is done once the smmu driver
shuts down.
During the device shutdown, the smmu calls shutdown
for all its consumers in order to indicate them to
stop all their dma activities.
Register the shutdown handler to stop the wlan
driver and avoid any dma operations.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593193981-30161-1-git-send-email-pillair@codeaurora.org
For QCA6390, normal power up and power down can't bring MHI
to a workable state. This happens especially in warm reboot
and rmmod and insmod. Host needs to write a few registers to
bring MHI to normal state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeauroro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-10-git-send-email-kvalo@codeaurora.org
For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.
Add MISC_CAPS_TCL_0_ONLY to control it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org
For QCA6390, the num_radios is 1 but it needs to process 2 lmac rings.
So use NUM_RXDMA_PER_PDEV to do another loop.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-8-git-send-email-kvalo@codeaurora.org
QCA6390 doesn't enable V2 map and ummap event, so the addr search
flags and type is different from IPQ8074. Assign correct search flags
and type for QCA6390.
Without this change, ping sometimes fails. With this change, now ping
is always successful.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-7-git-send-email-kvalo@codeaurora.org
For QCA6390 firmware, bss peer must be created before vdev_start, so delay
vdev_start until bss peer is created.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-6-git-send-email-kvalo@codeaurora.org
For QCA6390, it processes the reg chan list event only for phy0,
and it goes to fallback if the phy_id is not valid. For a valid
phy_id but not 0, just discard the event.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-5-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
For QCA6390, it has 2 lmacs and thus 2 rxdmas. However, each rxdma has rxdma0
only, and doesn't have rxdma1. So for QCA6390, don't initialize rxdma1 related
rings such as rx_mon_buf_ring, rx_mon_dst_ring and rx_mon_desc_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-3-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org
For QCA6390, it uses peer_map and peer_unmap V1. IPQ8074 uses V2.
Redefine previous definition to peer_map2 and peer_unmap2.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-13-git-send-email-kvalo@codeaurora.org
For QCA6390, host puts hardware to Dual Band Simultaneous (DBS) mode by default
so both 2G and 5G bands can be used. Otherwise only the 5G band can be used.
QCA6390 doesn't provide band_to_mac configuration and firmware will do the
band_to_mac map.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-12-git-send-email-kvalo@codeaurora.org
QCA6390 has very different wmi config parameters compared to IPQ8074,
so use different function to initialize wmi init config parameters.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-11-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and only one HW is registered to
mac80211. This one pdev manages both 2G radio and 5G radio.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-10-git-send-email-kvalo@codeaurora.org
Disable CE interrupt otherwise interrupt may come before host
initialized related context. This also fixes unbalanced interrupt
enablement.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-9-git-send-email-kvalo@codeaurora.org
Move function to get msi_addr and msi_data before srng setup,
otherwise srng is setup with no MSI configuration.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-8-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt so it needs msi_addr and msi_data
to generate interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-7-git-send-email-kvalo@codeaurora.org
This macro is evil as it's accesses ab variable in a hidden way. It's better
for readibility to access ab->hw_params.ce_count directly.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-6-git-send-email-kvalo@codeaurora.org
This macro is evil as it's accesses ab variable in a hidden way. It's better
for readibility to access ab->hw_params.host_ce_config directly.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-5-git-send-email-kvalo@codeaurora.org
QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.
The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org
Now some of the HAL register macros access ab variable in a hidden way, make ab
variable visible in the macro by adding it as an argument.
This is done in a separate patch to keep the patches simple. No functional changes.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-3-git-send-email-kvalo@codeaurora.org
QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org
There's no reason to have call for enable_pll_clk in ath10k_bmi_start(), move
it to ath10k_core_start() instead. This way it's possible to call
ath10k_bmi_start() from sdio.c during firmware dump creation. And also the
function call is more visible when it's in core.c.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597421745-4329-1-git-send-email-kvalo@codeaurora.org
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()'.
Fixes: 1863008369 ("ath10k: fix shadow register implementation for WCN3990")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802122227.678637-1-christophe.jaillet@wanadoo.fr
The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.
This is similar to a bug that syzkaller found in commit e4ff08a4d7
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda
The ath9k driver was so far only able to rekey PTK0 keys correctly due
to the best effort queue flush added with commit 62872a9b9a
("mac80211: Fix PTK rekey freezes and clear text leak").
Add the needed queue flush and set NL80211_EXT_FEATURE_CAN_REPLACE_PTK0
to tell mac80211 that the driver can now rekey PTK0 keys correctly and
no longer needs the best effort flush.
Effectively this prevents mac80211 to warn when rekeying a PTK0 key
only.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200804164152.175375-1-alexander@wetzel-home.de
The value for "aid" comes from skb->data so Smatch marks it as
untrusted. If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().
Fixes: 572e27c00c ("ath6kl: Fix AP mode connect event parsing and TIM updates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda
Kerneldoc expects attributes/parameters to be in '@*.: ' format and
gets confused if the variable does not follow the type/attribute
definitions.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/base.c:1111: warning: Function parameter or member 'ah' not described in 'ath5k_drain_tx_buffs'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@winlab.rutgers.edu>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-21-lee.jones@linaro.org
No effort has been made to document any of the function parameters here.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ies_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1749: warning: Function parameter or member 'ie_len' not described in '_wil_cfg80211_find_ie'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies1_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'ies2_len' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_ies' not described in '_wil_cfg80211_merge_extra_ies'
drivers/net/wireless/ath/wil6210/cfg80211.c:1780: warning: Function parameter or member 'merged_len' not described in '_wil_cfg80211_merge_extra_ies'
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/pcu.c:115: warning: Function parameter or member 'band' not described in 'ath5k_hw_get_frame_duration'
drivers/net/wireless/ath/ath5k/pcu.c:955: warning: Excess function parameter 'mode' description in 'ath5k_hw_pcu_init'
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Reyk Floeter <reyk@openbsd.org>
Cc: "W. S. Bell" <mentor@madwifi.org>
Cc: Luis Rodriguez <mcgrof@winlab.rutgers.edu>
Cc: Pavel Roskin <proski@gnu.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200814113933.1903438-10-lee.jones@linaro.org
On QCA6390 reg_start and reg_size values are different from IPQ8074 so we need
to change the values runtime. As we can't modify a static const variable
hw_srng_config directly, instead use it as a template, copy it and modify the
copy with correct values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-12-git-send-email-kvalo@codeaurora.org
On x86 and other non-qcom platforms, host needs to explicitly tell the firmware
to use the internal sleep clock. Some QCA6390 modules have OTP burnt with
external sleep clock selected, and these modules can't work expectedly unless
firmware selects internal sleep clock.
Add a field to hw_params to support this difference.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-11-git-send-email-kvalo@codeaurora.org
It's caused by reading memory out of boundary from target_ce_config_wlan.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-10-git-send-email-kvalo@codeaurora.org
The decoded_size is wrongly assigned in ath11k_qmi_msg_handlers and it results
in out of boundary access in qmi_decode. The correct decoded_size should be
calculated from the related ind_msg structure.
This issue is exposed with QCA6390 because it needs 11 small memory chunks
which are stored in qmi_wlanfw_request_mem_ind_msg_v01 and hence the
decoded_size exceeds the wrongly assigend decoded_size.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-9-git-send-email-kvalo@codeaurora.org
On x86 it's sometimes difficult to allocate a large contigous DMA
memory, so instead allocate blocks of small chunk memory.
In ath11k_qmi_msg_mem_request_cb() the error handling was cleaned up to avoid
an unused variable warning. Also changed the test from (ret < 0) to just (ret)
as the functions don't return any positive values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-8-git-send-email-kvalo@codeaurora.org
CE srng is used for control path and CE srng processing is done using tasklet
bottom half. Setup ce tasklet initialization and scheduling for control path.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-7-git-send-email-kvalo@codeaurora.org
Fill msi base address and msi data to be programmed in CE srang.
This is used by the srng to generate the msi interrupt.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-6-git-send-email-kvalo@codeaurora.org
QMI service instance id is used for qmi service lookup, IPQ8074 and QCA6390
uses different instance id for service lookup. Fill appropriate QMI service
instance id for respective targets.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-4-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.
Add support to create board name for different targets. This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.
As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.
At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org
QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org
Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.
Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org
This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org
Add support for setting up pci region and dma mask.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-6-git-send-email-kvalo@codeaurora.org
QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org
This is needed for splitting ahb and pci modules as they have different ring
mask settings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org
Define own firmware directory and settings for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org
With only IPQ8074 supported ath11k was only usable on Qualcomm architectures.
But now that we are adding QCA6390 PCI support to ath11k that's not the case
anymore and it can be used on any architecture supporting PCI. So remove the
dependency on ARCH_QCOM. After that there is also no need to depend on
COMPILE_TEST.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-2-git-send-email-kvalo@codeaurora.org
The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.
The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.
It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.
This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.
This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
When using QCA6174 PCI devices working in station mode, after connected
to AP, tx bitrate is always '1.0 MBit/s' in output of command 'iw wlan0
station dump'. (QCA6174 SDIO devices are working fine.)
After this patch, it show correct bitrate:
Station c4:04:15:5d:97:22 (on wls1)
inactive time: 312 ms
rx bytes: 31496
rx packets: 173
tx bytes: 8625
tx packets: 46
tx retries: 0
tx failed: 0
signal: -76 [-88, -80] dBm
signal avg: -75 [-82, -77] dBm
tx bitrate: 39.0 MBit/s MCS 4
rx bitrate: 26.0 MBit/s MCS 3
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-4-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES
This patch not effect the info of above 4 bit for all hardware, reason
as below:
NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.
NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.
NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.
If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719104041.57916-1-grandmaster@al2klimov.de
list_for_each_entry{_safe} is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry{_safe} is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry{_safe}, the element obtained
by list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change for the list_for_each_entry
case is as follows: (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595761112-11003-8-git-send-email-Julia.Lawall@inria.fr
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
Typo "destoy" made me wonder if correct patch is wrong; fix it. No
functional change.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724083910.GA31930@amd
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719105052.57997-1-grandmaster@al2klimov.de
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfGukwAAoJEG4XJFUm622bIdwIAKYV3lplb6mXyDdF1b3Yoxar
0IDUglXlJN+VIgvUQG4wOvxgDw7jp6q95BRi58VjafIFm+orjILvYFmwThLPYfIS
dA0ML9+zGnRMC+SIjZktXKG9lridQXyqexWHCFF9dT147GsF8+LIbfqT6denCLf7
vP26RSMAMK5Ed01V9qb5rtitaVbr+Bx+c7adV8tLH/gkWeTEp4CaDhNOkMJ0uRCV
QPZ8duF1Hz/QVMn9PAA8xGTH4bxIfSfWVJfSjG1uq349CZ+MjHleDeYWKh524ThV
49YTabR2DIKOWSgNzG7jsitz7K/420Y/NpuNeGWO+7czgYe2uEIrGDZkYPUPoS4=
=PTR1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfFWQeAAoJEG4XJFUm622bVAwH/3r2oR+NS1kNDNGi9nrLAIav
trLgPa2VbgPVgTcwIckfvZFl6BK9zo1KG6u6jYp45C6uNBJNESjarf8aLAXvXdFt
t0yBkb6OCUq+efoOFbxV2im6ER57aN27POsn74xrCeR3fwZgY9QSHRMjQ5x1tjWH
JdVatT6jtu2LuxsTjfS0K5kjeuyE0vE1iCUlsQ5qwcSLODGa9u7ydheoNcLOHvss
ACun8zXvWqJhTar+iJHiTJTWyQPE6es0V1SAw0RnTuLRRmtv/Q9Zx4YOH2d3JkOC
55mfgO3uNzw8fcJ5hoILHtXxhI2qtSkdydIFbE1U9CgBKE39Uo0VgFf9fl6VJRg=
=7a5a
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-2-refactormyself@gmail.com
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
