It's caused by reading memory out of boundary from target_ce_config_wlan.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-10-git-send-email-kvalo@codeaurora.org
The decoded_size is wrongly assigned in ath11k_qmi_msg_handlers and it results
in out of boundary access in qmi_decode. The correct decoded_size should be
calculated from the related ind_msg structure.
This issue is exposed with QCA6390 because it needs 11 small memory chunks
which are stored in qmi_wlanfw_request_mem_ind_msg_v01 and hence the
decoded_size exceeds the wrongly assigend decoded_size.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-9-git-send-email-kvalo@codeaurora.org
On x86 it's sometimes difficult to allocate a large contigous DMA
memory, so instead allocate blocks of small chunk memory.
In ath11k_qmi_msg_mem_request_cb() the error handling was cleaned up to avoid
an unused variable warning. Also changed the test from (ret < 0) to just (ret)
as the functions don't return any positive values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-8-git-send-email-kvalo@codeaurora.org
CE srng is used for control path and CE srng processing is done using tasklet
bottom half. Setup ce tasklet initialization and scheduling for control path.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-7-git-send-email-kvalo@codeaurora.org
Fill msi base address and msi data to be programmed in CE srang.
This is used by the srng to generate the msi interrupt.
Needed for PCI support.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-6-git-send-email-kvalo@codeaurora.org
QMI service instance id is used for qmi service lookup, IPQ8074 and QCA6390
uses different instance id for service lookup. Fill appropriate QMI service
instance id for respective targets.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-4-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.
Add support to create board name for different targets. This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.
As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.
At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org
PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org
QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org
Modem Host Interface (MHI) is a communication protocol to communicate with
external Qualcomm modems and Wi-Fi chipsets over high speed peripheral buses.
Even though MHI doesn’t dictate underlying physical layer, protocol and MHI
stack is structured for PCI based devices.
Register directly with MHI subsystem as a MHI device driver for firmware
download to QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-9-git-send-email-kvalo@codeaurora.org
This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org
Add support for setting up pci region and dma mask.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-6-git-send-email-kvalo@codeaurora.org
QCA6390 is a PCI based 11ax chipset, split AHB into own kernel module
ath11k_ahb.ko and add ath11k_pci.ko for PCI devices.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-5-git-send-email-kvalo@codeaurora.org
This is needed for splitting ahb and pci modules as they have different ring
mask settings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org
Define own firmware directory and settings for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org
With only IPQ8074 supported ath11k was only usable on Qualcomm architectures.
But now that we are adding QCA6390 PCI support to ath11k that's not the case
anymore and it can be used on any architecture supporting PCI. So remove the
dependency on ARCH_QCOM. After that there is also no need to depend on
COMPILE_TEST.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-2-git-send-email-kvalo@codeaurora.org
The mcs index of HT mode is 0 to 31, please refer http://mcsindex.com/.
Its spatial stream(Nss) number is from 1 to 4, mcs index is 0~7 for
Nss=1, 8~15 for Nss=2, 16~23 for Nss=3 and 24~31 is for Nss=4.
The mcs is reported from firmware in wmi_tlv_peer_stats_info of
event WMI_TLV_PEER_STATS_INFO_EVENTID, its range is from 0~15 for
QCA6174 SDIO and PCIe. It is for both Nss=1 and Nss=2, and it has 2
rate table supported_ht_mcs_rate_nss1 and supported_ht_mcs_rate_nss2
in ath10k, they are for Nss=1 and Nss=2, each table has 8 rates.
It need to find the matched row number with the mcs index, for example,
mcs index is 2, it is <=7, so it is Nss=1, and match row 2 in table of
Nss=1. If mcs index is 12, it is >= 8 and <= 15, so it is Nss=2, it
match row 4(12-8) in table of Nss=2. If mcs index is >=16, it is for
Nss=3/4, it need to add rate table, so it is not support in current
ath10k.
This patch is to find the row number in rate table of Nss=1 or Nss=2
with the mcs index reported from firmware.
This patch only effect the chips which supports_peer_stats_info of its
hw_params is true, it is true only for QCA6174 currently.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392294-13124-1-git-send-email-wgong@codeaurora.org
When using QCA6174 PCI devices working in station mode, after connected
to AP, tx bitrate is always '1.0 MBit/s' in output of command 'iw wlan0
station dump'. (QCA6174 SDIO devices are working fine.)
After this patch, it show correct bitrate:
Station c4:04:15:5d:97:22 (on wls1)
inactive time: 312 ms
rx bytes: 31496
rx packets: 173
tx bytes: 8625
tx packets: 46
tx retries: 0
tx failed: 0
signal: -76 [-88, -80] dBm
signal avg: -75 [-82, -77] dBm
tx bitrate: 39.0 MBit/s MCS 4
rx bitrate: 26.0 MBit/s MCS 3
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-4-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report many info to iw wlan0 link,
if it return for empty legacy and nss of arsta->txrate, then the other
stats after it will not be set.
It has 4 bit to set after the return:
NL80211_STA_INFO_TX_FAILED
NL80211_STA_INFO_RX_BITRATE
NL80211_STA_INFO_TX_BITRATE
NL80211_STA_INFO_TX_RETRIES
This patch not effect the info of above 4 bit for all hardware, reason
as below:
NL80211_STA_INFO_TX_FAILED is only for htt.disable_tx_comp is true, it
is for QCA6174 SDIO.
NL80211_STA_INFO_RX_BITRATE and NL80211_STA_INFO_TX_BITRATE are both
set in ath10k_mac_sta_get_peer_stats_info, it is only enabled for chips
which supports_peer_stats_info is true in hw_params, recently only for
QCA6174 SDIO, NL80211_STA_INFO_TX_BITRATE is set again in function
ath10k_mac_sta_get_peer_stats_info because the value which parsed from
arsta->tx_rate_code and arsta->tx_bitrate_kbps is correct for QCA6174
SDIO and PCIe, and the value arsta->txrate is not correct for QCA6174
SDIO and PCIe, so it need to set again with the correct value.
NL80211_STA_INFO_TX_RETRIES is use value of arsta->tx_retries, it is set
in ath10k_update_per_peer_tx_stats, which accumulate the retry_pkts in
HTT message from firmware, if the chips not support this feature, then
it is always 0 after accumulate, then iw wlan0 station dump always show
0 for retry count. If not set NL80211_STA_INFO_TX_RETRIES here, then it
is still 0, so the result is same, then set NL80211_STA_INFO_TX_RETRIES
has no effect.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-3-git-send-email-wgong@codeaurora.org
ath10k_sta_statistics is used to report info for iw wlan0 link,
it check ath10k_peer_stats_enabled, and ath10k_peer_stats_enabled
check WMI_SERVICE_PEER_STATS bit of ar->wmi.svc_map. SVCMAP() for
WMI_SERVICE_PEER_STATS was defined only for wmi_10x_svc_map and
wmi_10_4_svc_map interfaces, it missed in wmi_tlv_svc_map, so it is
not usable for iw wlan0 link for wmi tlv interface.
If firmware report WMI_TLV_SERVICE_PEER_STATS_INFO for wmi tlv, then
enable the WMI_SERVICE_PEER_STATS bit in ath10k, and then it pass check
in ath10k_peer_stats_enabled and ath10k_sta_statistics pass check.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00048
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597312029-32348-2-git-send-email-wgong@codeaurora.org
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719104041.57916-1-grandmaster@al2klimov.de
list_for_each_entry{_safe} is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry{_safe} is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry{_safe}, the element obtained
by list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change for the list_for_each_entry
case is as follows: (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595761112-11003-8-git-send-email-Julia.Lawall@inria.fr
Instead of using the firmware generated sequence number, use the one
already allocated by the mac80211 layer. This allows better control
of the sequence numbers and avoid to rely on same sequence for Data,
QOS Data and QOS Null Data packets.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-7-git-send-email-loic.poulain@linaro.org
This patch contains the following fixes:
- Use correct queue for submitting QoS packet. The queue id to use
is a one-to-one mapping with the TID.
- Don't encrypt a frame with IEEE80211_TX_INTFL_DONT_ENCRYPT flag.
- Use the 'special queue' for null packets, preventing the firmware
to submit it as AMPDU.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-5-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
The controller is capable of reporting TX indication which can be used
to report TX ack when IEEE80211_TX_CTL_REQ_TX_STATUS is set.
The support was only partially implemented.
The firmware can be configured for reporting event when a packet is
acked, without specifying which packet though. In order to send a
packet flagged with TX status callback, we need to stop the queue,
submit the packet and wait for the firmware ack event. Then the queue
can be restarted and mac80211 status callback called.
In case the packet is not acked, no ack event will be received,
therefore a timeout mechanism is introduced to restart the queue
and call the status cb in case no event is received after a 100ms.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-3-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
Typo "destoy" made me wonder if correct patch is wrong; fix it. No
functional change.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200724083910.GA31930@amd
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200719105052.57997-1-grandmaster@al2klimov.de
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfGukwAAoJEG4XJFUm622bIdwIAKYV3lplb6mXyDdF1b3Yoxar
0IDUglXlJN+VIgvUQG4wOvxgDw7jp6q95BRi58VjafIFm+orjILvYFmwThLPYfIS
dA0ML9+zGnRMC+SIjZktXKG9lridQXyqexWHCFF9dT147GsF8+LIbfqT6denCLf7
vP26RSMAMK5Ed01V9qb5rtitaVbr+Bx+c7adV8tLH/gkWeTEp4CaDhNOkMJ0uRCV
QPZ8duF1Hz/QVMn9PAA8xGTH4bxIfSfWVJfSjG1uq349CZ+MjHleDeYWKh524ThV
49YTabR2DIKOWSgNzG7jsitz7K/420Y/NpuNeGWO+7czgYe2uEIrGDZkYPUPoS4=
=PTR1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfFWQeAAoJEG4XJFUm622bVAwH/3r2oR+NS1kNDNGi9nrLAIav
trLgPa2VbgPVgTcwIckfvZFl6BK9zo1KG6u6jYp45C6uNBJNESjarf8aLAXvXdFt
t0yBkb6OCUq+efoOFbxV2im6ER57aN27POsn74xrCeR3fwZgY9QSHRMjQ5x1tjWH
JdVatT6jtu2LuxsTjfS0K5kjeuyE0vE1iCUlsQ5qwcSLODGa9u7ydheoNcLOHvss
ACun8zXvWqJhTar+iJHiTJTWyQPE6es0V1SAw0RnTuLRRmtv/Q9Zx4YOH2d3JkOC
55mfgO3uNzw8fcJ5hoILHtXxhI2qtSkdydIFbE1U9CgBKE39Uo0VgFf9fl6VJRg=
=7a5a
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
First set of patches for v5.9. This comes later than usual as I was
offline for two weeks. The biggest change here is moving Microchip
wilc1000 driver from staging. There was an immutable topic branch with
one commit moving the whole driver and the topic branch was pulled
both to staging-next and wireless-drivers-next. At the moment the only
reported conflict is in MAINTAINERS file, so I'm hoping the move
should go smoothly.
Other notable changes are ath11k getting 6 GHz band support and rtw88
supporting RTL8821CE. And there's also the usual fixes, API changes
and cleanups all over.
Major changes:
wilc1000
* move from drivers/staging to drivers/net/wireless/microchip
ath11k
* add 6G band support
* add spectral scan support
iwlwifi
* make FW reconfiguration quieter by not using warn level
rtw88
* add support for RTL8821CE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-2-refactormyself@gmail.com
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands. In this case, too, the non-gro path didn't bother checking
the return value. Plus, this had some clunky debugging functions that
duplicated code from elsewhere and was generally pretty messy. So, this
commit cleans that all up too.
Fixes: 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in napi_gro_receive()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org
To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.
Also remove a useless info print, it's more like a debug message anyway.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org
pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping
pdev_id ipq8074 ipq6018
------- ------- -------
0 0 0
1 2 1
2 1 Not applicable
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org
Convert to ath11k_hw_params to an array to make it possible add new hardware in
the future, for example IPQ6018 or QCA6390.
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-3-git-send-email-kvalo@codeaurora.org
A compromized ath10k peripheral is able to control the size argument
of memcpy in ath10k_pci_hif_exchange_bmi_msg.
The min result from previous line is not used as the size argument
for memcpy. Instead, xfer.resp_len comes from untrusted stream dma
input. The value comes from "nbytes" in ath10k_pci_bmi_recv_data,
which is set inside _ath10k_ce_completed_recv_next_nolock with the line
nbytes = __le16_to_cpu(sdesc.nbytes);
sdesc is a stream dma region which device can write to.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616132544.17478-1-bruceshenzk@gmail.com
We need this so that all hardware versions can coexist and
it's easier to manage everything then all hardware
directories are under ath11k directory.
Copy ath11k firmware files to
/lib/firmware/ath11k/IPQ8074/hw2.0/
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591709581-18039-3-git-send-email-akolli@codeaurora.org
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
Tested-on: QCA9984 PCI 10.4-3.6-00104
Tested-on: QCA9882 PCI 10.2.4-1.0-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591856446-26977-1-git-send-email-vnaralas@codeaurora.org
On wcn3990 we have "per_ce_irq = true". That makes the
ath10k_ce_interrupt_summary() function always return 0xfff. The
ath10k_ce_per_engine_service_any() function will see this and think
that _all_ copy engines have an interrupt. Without checking, the
ath10k_ce_per_engine_service() assumes that if it's called that the
"copy complete" (cc) interrupt fired. This combination seems bad.
Let's add a check to make sure that the "copy complete" interrupt
actually fired in ath10k_ce_per_engine_service().
This might fix a hard-to-reproduce failure where it appears that the
copy complete handlers run before the copy is really complete.
Specifically a symptom was that we were seeing this on a Qualcomm
sc7180 board:
arm-smmu 15000000.iommu: Unhandled context fault:
fsr=0x402, iova=0x7fdd45780, fsynr=0x30003, cbfrsynra=0xc1, cb=10
Even on platforms that don't have wcn3990 this still seems like it
would be a sane thing to do. Specifically the current IRQ handler
comments indicate that there might be other misc interrupt sources
firing that need to be cleared. If one of those sources was the one
that caused the IRQ handler to be called it would also be important to
double-check that the interrupt we cared about actually fired.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200609082015.1.Ife398994e5a0a6830e4d4a16306ef36e0144e7ba@changeid
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
With addition of 6Ghz channels, it is possible that wmi buffer size can
exceed the maximum wmi buffer size. So iterate over the channel list,
and send multiple messages till channel list is empty.
Also mark PSC channel flag for 6GHz channels accordingly.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-8-pradeepc@codeaurora.org
If 6 ghz channel is a Preferred Scanning Channel(PSC), mark
the channel flag accordingly when updating channel list to firmware.
This will be used when making scanning decision in 6GHz channels.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-6-pradeepc@codeaurora.org
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
As 6GHz cahnnel numbers overlap with those of 5GHz and 2GHz bands,
it is necessary to use frequency when determining the band info
in rx path.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-4-pradeepc@codeaurora.org
In some ath files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-4-f.suligoi@asem.it
ath10k_htt_tx_free_msdu_id() has a lockdep assertion that htt->tx_lock
is held. Acquire the lock in a couple of error paths when calling that
function to ensure this condition is met.
Fixes: 6421969f24 ("ath10k: refactor tx pending management")
Fixes: e62ee5c381 ("ath10k: Add support for htt_data_tx_desc_64 descriptor")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604105901.1.I5b8b0c7ee0d3e51a73248975a9da61401b8f3900@changeid
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
The ath10k/qmi.h header file contains a declaration for the function
ath10k_qmi_register_service_notifier(). This function doesn't exist.
Remove the declaration.
This patch is a no-op and was just found by code inspection.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Check for "AR6003 or later" is slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath6kl.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-8-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'thermal_cooling_device_register()' fails, we must undo what has been
allocated so far. So we must go to 'err_thermal_destroy' instead of
returning directly
In case of error in 'ath11k_thermal_register()', the previous
'thermal_cooling_device_register()' call must also be undone. Move the
'ar->thermal.cdev = cdev' a few lines above in order for this to be done
in 'ath11k_thermal_unregister()' which is called in the error handling
path.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513201454.258111-1-christophe.jaillet@wanadoo.fr
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151758.GA4962@embeddedor
HTT EXT stats comes in stream of TLVs spanning over multiple
messages. Currently completion is being sent for each message
which is creating a race where stats_req is being accessed
for filling in second message after the memory is already
freed in release operation. Fix this by issuing completion
once all the messages are received and processed. Driver
knows this info from DONE bit set in htt msg.
Also fix locking required for htt stats.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589221074-28778-1-git-send-email-pradeepc@codeaurora.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151120.GA4469@embeddedor
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508075323.81128-1-weiyongjun1@huawei.com
Pointer info is being assigned twice, once at the start of the function
and secondly when it is just about to be accessed. Remove the redundant
initialization and keep the original assignment to info that is close
to the memcpy that uses it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507164318.56570-1-colin.king@canonical.com
gcc-10 correctly points out a bug with a zero-length array in
struct ath10k_pci:
drivers/net/wireless/ath/ath10k/ahb.c: In function 'ath10k_ahb_remove':
drivers/net/wireless/ath/ath10k/ahb.c:30:9: error: array subscript 0 is outside the bounds of an interior zero-length array 'struct ath10k_ahb[0]' [-Werror=zero-length-bounds]
30 | return &((struct ath10k_pci *)ar->drv_priv)->ahb[0];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/ath/ath10k/ahb.c:13:
drivers/net/wireless/ath/ath10k/pci.h:185:20: note: while referencing 'ahb'
185 | struct ath10k_ahb ahb[0];
| ^~~
The last addition to the struct ignored the comments and added
new members behind the array that must remain last.
Change it to a flexible-array member and move it last again to
make it work correctly, prevent the same thing from happening
again (all compilers warn about flexible-array members in the
middle of a struct) and get it to build without warnings.
Fixes: 521fc37be3 ("ath10k: Avoid override CE5 configuration for QCA99X0 chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-2-arnd@arndb.de
gcc-10 started warning about out-of-bounds access for zero-length
arrays:
In file included from drivers/net/wireless/ath/ath10k/core.h:18,
from drivers/net/wireless/ath/ath10k/htt_rx.c:8:
drivers/net/wireless/ath/ath10k/htt_rx.c: In function 'ath10k_htt_rx_tx_fetch_ind':
drivers/net/wireless/ath/ath10k/htt.h:1683:17: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'struct htt_tx_fetch_record[0]' [-Wzero-length-bounds]
1683 | return (void *)&ind->records[le16_to_cpu(ind->num_records)];
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/htt.h:1676:29: note: while referencing 'records'
1676 | struct htt_tx_fetch_record records[0];
| ^~~~~~~
Make records[] a flexible array member to allow this, moving it behind
the other zero-length member that is not accessed in a way that gcc
warns about.
Fixes: 22e6b3bc5d ("ath10k: add new htt definitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200509120707.188595-1-arnd@arndb.de
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151921.GA5083@embeddedor
In case of error, 'qcom_wcnss_open_channel()' must be undone by a call to
'rpmsg_destroy_ept()', as already done in the remove function.
Fixes: 5052de8def ("soc: qcom: smd: Transition client drivers from smd to rpmsg")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507043619.200051-1-christophe.jaillet@wanadoo.fr
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507041127.GA31587@embeddedor
Bus level header files needs to be abstracted by upper
layer. Remove bus layer includes by adding appropriate header
files.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-4-govinds@codeaurora.org
Current design supports only AHB interface for
11ax chipset. Refactor the code by adding hif layer
for bus level abstraction to support PCI based device.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200506094400.4740-2-govinds@codeaurora.org
Sparse warned:
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: warning: incorrect
type in assignment (different base types)
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: expected
restricted __le32 [usertype] reset_after_request
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3013:34: got unsigned int
[usertype] reset
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Fixes: 0f7cb26830 ("ath10k: add rx bitrate report for SDIO")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588747649-18051-1-git-send-email-kvalo@codeaurora.org
gcc-10 warns about accesses inside of a zero-length array:
drivers/net/wireless/ath/wil6210/cfg80211.c: In function 'wil_cfg80211_scan':
drivers/net/wireless/ath/wil6210/cfg80211.c:970:23: error: array subscript 255 is outside the bounds of an interior zero-length array 'struct <anonymous>[0]' [-Werror=zero-length-bounds]
970 | cmd.cmd.channel_list[cmd.cmd.num_channels++].channel = ch - 1;
| ~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/ath/wil6210/wil6210.h:17,
from drivers/net/wireless/ath/wil6210/cfg80211.c:11:
drivers/net/wireless/ath/wil6210/wmi.h:477:4: note: while referencing 'channel_list'
477 | } channel_list[0];
| ^~~~~~~~~~~~
Turn this into a flexible array to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200505143332.1398524-1-arnd@arndb.de
Currently when the sending of any management pkt
via wmi command fails, the packet is being unmapped
freed in the error handling. But the idr entry added,
which is used to track these packet is not getting removed.
Hence, during unload, in wmi cleanup, all the entries
in IDR are removed and the corresponding buffer is
attempted to be freed. This can cause a situation where
one packet is attempted to be freed twice.
Fix this error by rmeoving the msdu from the idr
list when the sending of a management packet over
wmi fails.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588667015-25490-1-git-send-email-pillair@codeaurora.org
The qmi infrastructure sends the client a del_server
event when the client releases its qmi handle. This
is not the msg indicating the actual qmi server exiting.
In such cases the del_server msg should not be processed,
since the wifi firmware does not reset its qmi state.
Hence skip the processing of del_server event when the
driver is unloading.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588663061-12138-1-git-send-email-pillair@codeaurora.org
The driver is not handling monitor status descriptor whenever
the done bit of status descriptor is not set by hardware. This leave
a stale entry in monitor status ring and flooding warning message.
Fix that by removing the descriptor and move forward to next one
in monitor status ring.
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588642063-6950-1-git-send-email-rmanohar@codeaurora.org
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504201224.GA32282@embeddedor
Some devices like TP-Link TL-WN722N produces this kind of messages
frequently.
kernel: ath: phy0: Short RX data len, dropping (dlen: 4)
This warning is useful for developers to recognize that the device
(Wi-Fi dongle or USB hub etc) is noisy but not for general users. So
this patch make this warning to debug message.
Reported-By: Denis <pro.denis@protonmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207539
Fixes: cd486e627e ("ath9k_htc: Discard undersized packets")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504214443.4485-1-masashi.honma@gmail.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504200838.GA31974@embeddedor
This patch add supports to reset the per peer htt stats.
Usage:
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/<peer MAC addr>/htt_peer_stats_reset
While doing so, sync the wmi services between FW and host.
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588610147-20231-1-git-send-email-tamizhr@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
htt stats are not working after htt peer stats display
and also after htt peer stats reset. Trying to dump htt
stats shows "Resource temporarily unavailable".
This is because of "ar->debug.htt_stats.stats_req" member is being
consecutively used for all htt stats without being reset
during the previous usage. Hence assigning NULL to this member
after freeing the allocated memory fixes the issue.
console logs below:
# echo 9 >/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
9
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats
cat: can't open '/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats'
: Resource temporarily unavailable
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588592755-10427-1-git-send-email-ssreeela@codeaurora.org
Fix the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:2964:1-39: WARNING: Assignment
of 0/1 to bool variable
drivers/net/wireless/ath/ath11k/dp_rx.c:2965:1-38: WARNING: Assignment
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113336.41249-1-yanaijie@huawei.com
Add the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-4-git-send-email-pillair@codeaurora.org
Move the msa resources setup out of qmi init and
setup the msa resources as a part of probe before
the qmi init is done.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-3-git-send-email-pillair@codeaurora.org
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
As the exisiting CE configurations are defined in global, there
are the chances of QCA99X0 family chipsets CE configurations
are getting changed by the ath10k_pci_override_ce_config()
function.
The override will be hit and CE5 configurations will be changed,
when the user bring up the QCA99X0 chipsets along with QCA6174
or QCA9377 chipset. (Bring up QCA99X0 family chipsets after
QCA6174 or QCA9377).
Hence, fixing this issue by moving the global CE configuration
to radio specific CE configuration.
Tested hardware: QCA9888 & QCA6174
Tested firmware: 10.4-3.10-00047 & WLAN.RM.4.4.1.c3-00058
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587649759-14381-1-git-send-email-mkenna@codeaurora.org
In Multi-AP VAP scenario with frequent interface up-down, there is a
chance that ath11k_mgmt_over_wmi_tx_work() will dequeue a skb
corresponding to currently deleted/stopped vdev.
FW will assert on receiving mgmt_tx_wmi cmd for already deleted vdev.
Hence adding validation checks for arvif present on the corresponding
ar before sending mgmt_tx_wmi cmd.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588049126-1490-2-git-send-email-murugana@codeaurora.org
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: d0998eb84e ("ath11k: optimise ath11k_dp_tx_completion_handler")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104621.23752-1-weiyongjun1@huawei.com
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5d ("ath10k: add large size for BMI download data for SDIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com
As of now HE operation element in bss_conf includes variable length
optional field followed by other HE variable. Though the optional
field never be used, actually it is referring to next member of the
bss_conf structure which is not correct. Fix it by declaring needed
HE operation fields within bss_conf itself.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Link: https://lore.kernel.org/r/1587768108-25248-2-git-send-email-rmanohar@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For legacy mode, tx bitrate not show correct sometimes, for example:
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 19672 bytes (184 packets)
TX: 9851 bytes (87 packets)
signal: -51 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 2.8 MBit/s
This patch use the tx bitrate info from WMI_TLV_PEER_STATS_INFO_EVENTID
report from firmware, and tx bitrate show correct.
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 13973 bytes (120 packets)
TX: 6737 bytes (57 packets)
signal: -52 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 54.0 MBit/s
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, it is enabled only for
"qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-5-wgong@codeaurora.org
The rate code and rate kbps report by WMI_TLV_PEER_STATS_INFO_EVENTID
from firmware contains all the bitrate info which include OFDM, CCK,
HT/VHT, and mac80211 need the struct rate_info which include below
parameters:
flags: bitflag of flags from &enum rate_info_flags
mcs: mcs index if struct describes an HT/VHT/HE rate
legacy: bitrate in 100kbit/s for 802.11abg
nss: number of streams (VHT & HE only)
bw: bandwidth (from &enum rate_info_bw)
For OFDM/CCK, its rate kbps indicate the bitrate, for HT/VHT, mac80211
need the above 5 parameters to cacluate the bitrate and show by iw.
After parse the bitrate info, iw show the correct rx bitrate:
localhost ~ # iw wlan0 link
rx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
rx bitrate: 40.5 MBit/s MCS 2 40MHz
rx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 54.0 MBit/s
rx bitrate: 48.0 MBit/s
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-4-wgong@codeaurora.org
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
For wmi tlv type, firmware disable peer stats info by default, after
enable it, firmware will report WMI_TLV_PEER_STATS_INFO_EVENTID if
ath10k send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware.
Enable it will only set a flag in firmware, firmware will not report
it without receive request WMI command.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-2-wgong@codeaurora.org
The '>' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath5k/ani.c:504:56-61: WARNING: conversion to
bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094037.23048-1-yanaijie@huawei.com
ADC & I/Q calibrations could take infinite time to comple, since they
depend on received frames. In particular the I/Q mismatch calibration
requires receiving of OFDM frames for completion. But in the 2.4GHz
band, a station could receive only CCK frames for a very long time.
And while we wait for the completion of one of the mentioned
calibrations, the NF calibration is blocked. Moreover, in some
environments, I/Q calibration is unable to complete until a correct
noise calibration will be performed due to AGC behaviour.
In order to avoid delaying NF calibration on forever, limit the maximum
duration of ADCs & I/Q calibrations. If the calibration is not completed
within the maximum time, it will be interrupted and a next calibration
will be performed. The code that selects the next calibration has been
reworked to the loop so incompleted calibration will be respinned later.
Ð maximum calibration time of 30 seconds was selected to give the
calibration enough time to complete and to not interfere with the long
(NF) calibration.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-7-ryazanov.s.a@gmail.com
Previously after the calibration validity period is over,
calibrations are invalidated in a one at time manner. So, for AR9002
family, which has three calibrations, the full recalibration interval
becomes 3 x ATH_RESTART_CALINTERVAL. And each next calibration will be
separated by the ATH_RESTART_CALINTERVAL time from a previous one.
It seems like it is better to do whole recalibration at once. Also, this
change makes the driver behaviour a little simpler. So, invalidate all
calibrations at once at the end of the calibration validity interval.
This change affects only AR9002 chips family, since the AR9003 utilize
only a single calibration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-6-ryazanov.s.a@gmail.com
NF calibration and other elements of long calibration are usually faster
than ADCs & I/Q calibrations due to independence of receiption of the
OFDM signal. Moreover sometime I/Q calibration can not be completed at
all without preceding NF calibration. This is due to AGC, which has a
habit to block a weak signal without regular NF calibration. Thus, we do
not need to deferr the long calibration forever.
So, if the long calibration is requested, then deferr the ADCs & I/Q
calibration(s) and run the longcal (the NF calibration in particular) to
obtain fresh noise data.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-5-ryazanov.s.a@gmail.com
Each of AGC & I/Q calibrations can take a long time. Long calibration
and NF calibration in particular are forbiden for parallel run with
ADC & I/Q calibrations. So, the chip could not be ready to perform the
long calibration at the time of request. And a request to perform the
long calibration may be lost.
In order to fix this, preserve the long calibration request as a
calibration state flag and restore the long calibration request each
time the calibration function is called again (i.e. on each subsequent
ivocation of the short calibration).
This feature will be twice useful after the next change, which will
make it possible to start the long calibration before all ADCs & I/Q
calibrations are completed.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-4-ryazanov.s.a@gmail.com
The NFCAL_PENDING flag is set by the ath9k_hw_start_nfcal() routine,
so there is no reason to set it manually after calling it during the
AR9002 calibrations initialization.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-3-ryazanov.s.a@gmail.com
ADC calibration is only required for a 80 MHz sampling rate (i.e. for
40 MHz channels), when the chip utilizes the pair of ADCs in interleved
mode. Calibration on a 20 MHz channel will never be completed.
Previous channel check is trying to exclude all channels where the
calibration will get stuck. It effectively blocks the calibration run
for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g.
legacy mode channels).
Fix this issue by reworking the channel check to explicitly allow ADCs
gain & DC offset calibrations for HT40 channels only. Also update the
complicated comment to make it clear that these calibrations are for
multi-ADC mode only.
Stuck ADCs calibration blocks the NF calibration, what could make it
impossible to work in a noisy evironment: too big Rx attentuation,
invalid RSSI value, etc. So this change is actually more of a NF
calibration fix rather then the ADC calibration fix.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sdio chip use DMA buffer to receive TX packet from ath10k, and it has
limitation of each buffer, if the packet size exceed the credit size,
it will trigger error in firmware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422084719.3479-1-wgong@codeaurora.org
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-3-wgong@codeaurora.org
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
This patch change the TX packet from single packet to a large length
bundle packet, max size is 32, it results in significant performance
improvement on TX path.
Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it
improves TCP RX throughput (values in Mbps):
TCP-RX TCP-TX UDP-RX UDP-TX
use workqueue_tx_complete 423 357 448 412
change it to ar->workqueue 410 360 449 414
change it to ar->workqueue_aux 405 339 446 401
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
It only enable bundle for sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-2-wgong@codeaurora.org
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion
to bool not needed here
drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123745.4159-1-yanaijie@huawei.com
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:255:46-51: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123718.3384-1-yanaijie@huawei.com
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
Convert ath10k_hif_swap_mailbox() to a more generic op so that bus drivers can
do more than just swap the mailbox, for example set power save settings like in
the following sdio patch.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-2-git-send-email-kvalo@codeaurora.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
should not overwrite the error code. No buffer available then return
invalid. For other failures return the error code of actual failure.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586776872-25766-1-git-send-email-gsamin@codeaurora.org
Rx_filter flags are set with default filter flags during
wifi up/down sequence even though the 'ext_rx_stats' debugfs
is enabled as 1. So, that we are not getting proper per peer
rx_stats.
Hence, fixing this by setting the missing rx_filter when
ext_rx_stats is already set/enabled.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-3-git-send-email-mkenna@codeaurora.org
After setting fixed vht-rate if new station is trying to
assoc with mu_bfee cap, or if a sta is already connected
with mu_bfee cap then set the fixed vht-rate and
reconnecting the sta, FW assert is happening.
So to avoid this, reset the MU_BEAMFORMEE bit in vht->caps,
if mcs_index is invalid for nss 1.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-2-git-send-email-mkenna@codeaurora.org
Debugfs pdev entries should be cleaned up during the crash
on recovery. If not, mac register will fail for the reason
that it is already registered during core reconfigure.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-1-git-send-email-mkenna@codeaurora.org
During RX, accessing the reo dest ring descriptor directly is consuming
a lot of CPU cycles. Accessing the descriptor after copying it locally
has improved CPU usage by around ~10-15% while measuring throughput
in RX DBTC test cases(all radios are involved in the throughput
measurement).
HW tested: IPQ8074
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421797-885-1-git-send-email-mpubbise@codeaurora.org
Unlike CE interrupts, DP interrupts are not enabled/disabled at
source; they are enabled/disabled only at GIC level, therefore
it is required to set IRQ_DISABLE_UNLAZY flag to avoid spurious
interrupts.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421013-23025-1-git-send-email-mpubbise@codeaurora.org
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
sdio bus bandwidth is low, sometimes for high performance TX test,
it will lack of ath10k_sdio_bus_request, it will print message:
ath10k_sdio mmc1:0001:1: unable to allocate bus request for async request
change the num from 64 to 1024 will not happen it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-3-wgong@codeaurora.org
For sdio chip, it is high latency bus, all the TX packet's content will
be tranferred from HOST memory to firmware memory via sdio bus, then it
need much more memory in firmware than low latency bus chip, for low
latency chip, such as PCI-E, it only need to transfer the TX descriptor
via PCI-E bus to firmware memory. For sdio chip, reduce the complexity of
TX logic will help TX efficiency since its memory is limited, and it will
reduce the TX circle's time of each packet and then firmware will have more
memory for TX since TX complete also need memeory.
This patch disable TX complete indication from firmware for htt data
packet, it will not have TX complete indication from firmware to ath10k.
It will cut the cost of bus bandwidth of TX complete and make the TX
logic of firmware simpler, it results in significant performance
improvement on TX path.
Udp TX throughout is 130Mbps without this patch, and it arrives
400Mbps with this patch.
The downside of this patch is the command "iw wlan0 station dump" will
show 0 for "tx retries" and "tx failed" since all tx packet's status
is success.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200212080415.31265-2-wgong@codeaurora.org
In ath9k_hif_usb_rx_cb interface number is assumed to be 0.
usb_ifnum_to_if(urb->dev, 0)
But it isn't always true.
The case reported by syzbot:
https://lore.kernel.org/linux-usb/000000000000666c9c05a1c05d12@google.com
usb 2-1: new high-speed USB device number 2 using dummy_hcd
usb 2-1: config 1 has an invalid interface number: 2 but max is 0
usb 2-1: config 1 has no interface number 0
usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice=
1.08
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
general protection fault, probably for non-canonical address
0xdffffc0000000015: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0
Call Trace
__usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650
usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716
dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966
call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404
expire_timers kernel/time/timer.c:1449 [inline]
__run_timers kernel/time/timer.c:1773 [inline]
__run_timers kernel/time/timer.c:1740 [inline]
run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786
__do_softirq+0x21e/0x950 kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x178/0x1a0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:546 [inline]
smp_apic_timer_interrupt+0x141/0x540 arch/x86/kernel/apic/apic.c:1146
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829
Reported-and-tested-by: syzbot+40d5d2e8a4680952f042@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200404041838.10426-6-hqjagain@gmail.com
Currently sta airtime is updated without any lock in case of
host based airtime calculation. Which may result in accessing the
invalid sta pointer in case of continuous station connect/disconnect.
This patch fix the kernel null pointer dereference by updating the
station airtime with proper RCU lock in case of host based airtime
calculation.
Proceeding with the analysis of "ARM Kernel Panic".
The APSS crash happened due to OOPS on CPU 0.
Crash Signature : Unable to handle kernel NULL pointer dereference
at virtual address 00000300
During the crash,
PC points to "ieee80211_sta_register_airtime+0x1c/0x448 [mac80211]"
LR points to "ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core]".
The Backtrace obtained is as follows:
[<bf880238>] (ieee80211_sta_register_airtime [mac80211]) from
[<bf945a38>] (ath10k_txrx_tx_unref+0x17c/0x364 [ath10k_core])
[<bf945a38>] (ath10k_txrx_tx_unref [ath10k_core]) from
[<bf9428e4>] (ath10k_htt_txrx_compl_task+0xa50/0xfc0 [ath10k_core])
[<bf9428e4>] (ath10k_htt_txrx_compl_task [ath10k_core]) from
[<bf9b9bc8>] (ath10k_pci_napi_poll+0x50/0xf8 [ath10k_pci])
[<bf9b9bc8>] (ath10k_pci_napi_poll [ath10k_pci]) from
[<c059e3b0>] (net_rx_action+0xac/0x160)
[<c059e3b0>] (net_rx_action) from [<c02329a4>] (__do_softirq+0x104/0x294)
[<c02329a4>] (__do_softirq) from [<c0232b64>] (run_ksoftirqd+0x30/0x90)
[<c0232b64>] (run_ksoftirqd) from [<c024e358>] (smpboot_thread_fn+0x25c/0x274)
[<c024e358>] (smpboot_thread_fn) from [<c02482fc>] (kthread+0xd8/0xec)
Tested HW: QCA9888
Tested FW: 10.4-3.10-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585736290-17661-1-git-send-email-vnaralas@codeaurora.org
Enable radar detection in secondary segment for VHT160 and VHT80+80 mode
on DFS channels. Otherwise, when injecting radar pulse in the secondary
segment, the DUT can't detect radar pulse.
Tested: qca9984 with firmware ver 10.4-3.10-00047
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-2-git-send-email-ssreeela@codeaurora.org
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.comhttps://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585574792-719-1-git-send-email-ssreeela@codeaurora.org
The mgmt tx count reference is incremented/decremented on every mgmt tx and on
tx completion event from firmware.
In case of an unexpected mgmt tx completion event from firmware,
the counter would underflow. Avoid this by decrementing
only when the tx count is greater than 0.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585567028-9242-1-git-send-email-srirrama@codeaurora.org
Increase the tx completion ring size to 0x8000.Also set the
idr size to be same as the completion ring size.
This avoids backpressure on the TX Completion and
corresponding TCL Data ring during high data traffic.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585567006-9173-1-git-send-email-srirrama@codeaurora.org
Currently the error message refers to the command WMI_TWT_DIeABLE_CMDID
which looks like a cut-n-paste mangled typo. Fix the message to match
the command WMI_BSS_COLOR_CHANGE_ENABLE_CMDID that failed.
Fixes: 5a032c8d19 ("ath11k: add WMI calls required for handling BSS color")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200327192639.363354-1-colin.king@canonical.com
Pktlog data are different among the chipset & chipset versions.
As part of enhancing the user space script to decode the pktlog
trace events generated, it is desirable to know which chipset or
which chipset version has provided the events and thereby decode
the pktlogs appropriately.
Pktlog checksum helps to determine the chipset variant which is
given by the firmware in the struct wmi_ready_event.
Pktlog checksums are computed during the firmware build.
So, adding that pktlog checksum in the pklog trace events.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585234155-30574-1-git-send-email-mkenna@codeaurora.org
There is a race condition, when the user writes 'hw-restart' and
'hard' in the simulate_fw_crash debugfs file without any delay.
In the above scenario, the firmware dump work queue(scheduled by
'hard') should be handled gracefully, while the target is in the
'hw-restart'.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Co-developed-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213077-28439-1-git-send-email-mkenna@codeaurora.org
Add support to test aggregation procedures (addba/addba_resp/delba)
manually by adding the required callbacks in sta debugfs files.
To enable automatic aggregation in target,
echo 0 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
To send addba response,
echo 0 25 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
To send addba,
echo 1 32 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
To send delba,
echo 0 1 37 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213026-28406-1-git-send-email-mkenna@codeaurora.org
drivers/net/wireless/ath/ath11k/thermal.h:45:1:
warning: no return statement in function returning non-void [-Wreturn-type]
drivers/net/wireless/ath/ath11k/core.c:416:28: error:
passing argument 1 of 'ath11k_thermal_unregister' from incompatible pointer type [-Werror=incompatible-pointer-types]
Add missing return 0 in ath11k_thermal_set_throttling,
and fix ath11k_thermal_unregister param type.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200403083414.31392-1-yuehaibing@huawei.com
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.
Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.
Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.
Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of pdev based reo destination ring
selection is replaced by hash based ring selection so as to
ensure all the available rings are utilized for better performance.
The 4 reo destination rings are selected by the HW based on the
hash value computed from the received packet based on the 5 tuple
{ip src/ip dst/src port/dst port/protocol}. Out of the 32 hash values
used by the hw, the driver assigns 8 values per reo destination ring
to each of the 4 reo destination rings.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before dumping tx_stats proper validation was not been taken care of.
Due to which we were encountering null pointer dereference(kernel panic).
This scenario will arise when a station is getting disconnected and
we are changing the STA state by ath11k_mac_op_sta_state and assigning
tx_stats as NULL and after this the mac80211 will destroy the
debugfs entry from where we are trying to read the stats.
If anyone tries to dump tx_stats for that STA in between setting
tx_stats to NULL and debugfs file removal without checking the NULL
value it will run into a NULL pointer exception.
Proceeding with the analysis of "ARM Kernel Panic".
The APSS crash happened due to OOPS on CPU 3.
Crash Signature : Unable to handle kernel NULL pointer dereference at
virtual address 00000360
During the crash,
PC points to "ath11k_debug_htt_stats_init+0x16ac/0x1acc [ath11k]"
LR points to "ath11k_debug_htt_stats_init+0x1688/0x1acc [ath11k]".
The Backtrace obtained is as follows:
[<ffffffbffcfd8590>] ath11k_debug_htt_stats_init+0x16ac/0x1acc [ath11k]
[<ffffffc000156320>] do_loop_readv_writev+0x60/0xa4
[<ffffffc000156a5c>] do_readv_writev+0xd8/0x19c
[<ffffffc000156b54>] vfs_readv+0x34/0x48
[<ffffffc00017d6f4>] default_file_splice_read+0x1a8/0x2e4
[<ffffffc00017c56c>] do_splice_to+0x78/0x98
[<ffffffc00017c63c>] splice_direct_to_actor+0xb0/0x1a4
[<ffffffc00017c7b4>] do_splice_direct+0x84/0xa8
[<ffffffc000156f40>] do_sendfile+0x160/0x2a4
[<ffffffc000157980>] SyS_sendfile64+0xb4/0xc8
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dumping the SRNG stats during FW assert, this would help
in debugging ring stuck issues.
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fill the channel information from rx channel for the packet
which has invalid channel info from meta data.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Firmware sends HTT event to host whenever there is a
backpressure on RX rings, Handling such event and dumping
info on the console under the "ATH11K_DBG_DP_HTT" debug level.
Fetching RX ring backpressure histogram from FW via htt_stats debugfs.
#echo "24" > /sys/kernel/debug/ath11k/ipq8074/macX/htt_stats_type
#cat /sys/kernel/debug/ath11k/ipq8074/macX/htt_stats
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds code to handle the BSS_CHANGED_BSS_COLOR flag. It will
trigger the propagation of BSS color settings into the FW. Handling is
slightly different between AP and STA interfaces.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the he_operation field of the beacon sets a BSS color, we need to inform
the FW of the settings. This patch adds the WMI command handlers required
to do so.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver currently does not use wake_txq_queue. This leads to the
tx_queue_len being defaulted to 1000. Setting this parameter will
change the queue_len to 4096 which is more fitting for HE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enabling PN checking in the hardware; hardware checks
the PN of the received packets and reports the errors
to the host for further handling; default action is to
drop such packets. TSC (TKIP sequence counter)
validation is also offloaded.
Hardware validates PN/TSC only for unicast packets;
for group addressed packets, PN validation is done
in mac80211.
PN errors are reported to the driver via WBM RX release
ring and can be dumped by using the following command.
"cat /sys/kernel/debug/ath11k/soc_rx_stats | grep -i pn"
Sample Output:
PN check fail: 210
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IPQ8074 HW has support to verify the PN of the received frames.
For all frames except for fragmented ones, HW checks the PN and
delivers them to the driver. For fragmented frames, driver is
required to do a little more; it has to reassemble the fragments
and then reinject them to the HW for verifying the PN. Currently,
to keep the logic simple, PN verifcation is disabled in HW and is
handled in mac80211 for all the frames (fragmented and unfragmented).
On the contrary, offloading PN Validation to the HW brings important
benefits. It reduces CPU cycles spent on the host CPU for verifying
the same; helps in enabling features which improve performance like
mac80211 fast RX path, enabling multiple REO rings for parallel RX
processing, 802.11 decapsulation offloading. All these features are
dependent on PN offload which in turn is dependent on handling of
the received fragments in the driver.
When TKIP security is used, additional handling is required while
processing the fragments; since MIC is computed on an MSDU in TKIP,
only the last fragment has the MIC info. In this case, driver has to
compute the MIC after reassembly and compare it against the MIC
present in the frame. For this, MICHAEL_MIC kernel crypto library
APIs are used and the dependencies are appropriately set.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994 ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CONFIG_ATH5K_AHB could be enabled on ATH25 system without enabling
ATH5K driver itself. This does not make sense because CONFIG_ATH5K_AHB
controls object build within drivers/net/wireless/ath/ath5k/ so enabling
it without CONFIG_ATH5K brings nothing.
Add proper dependency to CONFIG_ATH5K_AHB.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there is WMI command failure, 'peer->sta' was not getting
cleaned up, and mac80211 frees the 'sta' memory, which is causing
the below page fault.
Cleaning up the sta pointer in ath11k whenever peer delete command
is sent.
Unable to handle kernel paging request at virtual address 200080000006a
pgd = ffffffc02a774000
[200080000006a] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
.
.
.
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.4.60 #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc00083c6d0 ti: ffffffc00083c6d0 task.ti: ffffffc00083c6d0
PC is at ath11k_dp_rx_process_mon_status+0x114/0x4e0 [ath11k]
LR is at ath11k_dp_rx_process_mon_status+0xe8/0x4e0 [ath11k]
pc : [<ffffffbffcf8e544>] lr : [<ffffffbffcf8e518>] pstate: 60000145
sp : ffffffc000833a30
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PPDU_CTRL type is missing in current pktlog dumps.
PPDU_CTRL is sent on CE5 with len 2560 bytes, current
driver ignores the payload len greter than 2048.
PPDU_CTRL of 2560 bytes is sent in two fragments of len 2028
and 532 bytes, but firmware reports pkt header has length as 2560
for both of the fragments.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In multi AP VAP scenario, when user bring down the interfaces. mac80211 mark
the interface down for the duplicated VAP and removed from the
local->interfaces list. ath11k_mac_get_arvif() is dependent on
ieee80211_iterate_active_interfaces_atomic() API to find the vdev id
in a given radio. In disassociation path, ath11k_mac_get_arvif() not
able to find the given vdev id since that VAP is removed from the
local->interfaces list. since sta_state callback throws error, mac80211 log
the below WARN_ON_ONCE message.
Fixed it by storing the allocated_vdev_map in each radio structure to maintain
the created vdev id bits. so that we can directly mask this against the given
vdev_id to find out the ar from the vdev_id.
WARN LOG:
WARNING: at net/mac80211/sta_info.c:1008
CPU: 2 PID: 2135 Comm: hostapd Not tainted #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc03a43d800 ti: ffffffc03a43d800 task.ti: ffffffc03a43d800
PC is at sta_set_sinfo+0x9dc/0xad4 [mac80211]
LR is at sta_set_sinfo+0x9cc/0xad4 [mac80211]
pc : [<ffffffbffce2a008>] lr : [<ffffffbffce29ff8>] pstate: 20000145
sp : ffffffc02cedb5f0
x29: ffffffc02cedb5f0 x28: ffffffc03a43d800
x27: 0000000000000014 x26: 0000000000000001
x25: ffffffc02cfc4000 x24: ffffffc036905508
x23: 0000000000000012 x22: ffffffc02cedb670
x21: ffffffc03bc64880 x20: ffffffc036904f80
x19: ffffffc02ae31000 x18: 00000000b019f3a1
x17: 0000000057f30331 x16: 00000000d8d1998e
x15: 0000000000000066 x14: 393a35383a36343a
x13: 6337203a6e6f6974 x12: 6174732065746169
x11: 636f737361736964 x10: 206f742064656c69
x9 : 6146203a31696669 x8 : 6337203a6e6f6974
x7 : 6174732065746169 x6 : ffffffc0008c33f6
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 00000000ffffff92
x1 : 0000000000000000 x0 : ffffffbffcea1091
---[ end trace 63c4b1c527345d5a ]---
Call trace:
[<ffffffbffce2a008>] sta_set_sinfo+0x9dc/0xad4 [mac80211]
[<ffffffbffce2a2c4>] __sta_info_flush+0xec/0x130 [mac80211]
[<ffffffbffce3dc48>] ieee80211_nan_func_match+0x1a34/0x23e4 [mac80211]
[<ffffffbffcde03e0>] __cfg80211_stop_ap+0x60/0xf0 [cfg80211]
[<ffffffbffcdb6d08>] __cfg80211_leave+0x110/0x150 [cfg80211]
[<ffffffbffcdb6d78>] cfg80211_leave+0x30/0x48 [cfg80211]
[<ffffffbffcdb6fbc>] cfg80211_init_wdev+0x22c/0x808 [cfg80211]
[<ffffffc0000afe28>] notifier_call_chain+0x50/0x84
[<ffffffc0000afefc>] raw_notifier_call_chain+0x14/0x1c
[<ffffffc0004ae94c>] call_netdevice_notifiers_info+0x5c/0x6c
[<ffffffc0004ae96c>] call_netdevice_notifiers+0x10/0x18
[<ffffffc0004aea80>] __dev_close_many+0x54/0xc0
[<ffffffc0004aeb50>] dev_close_many+0x64/0xdc
[<ffffffc0004b0b70>] rollback_registered_many+0x138/0x2f4
[<ffffffc0004b0d4c>] rollback_registered+0x20/0x34
[<ffffffc0004b34b4>] unregister_netdevice_queue+0x68/0xa8
[<ffffffbffce3870c>] ieee80211_if_remove+0x84/0xc0 [mac80211]
[<ffffffbffce3e588>] ieee80211_nan_func_match+0x2374/0x23e4 [mac80211]
[<ffffffbffcdc29e8>] cfg80211_wext_giwscan+0x1000/0x1140 [cfg80211]
[<ffffffbffcb2a87c>] backport_genlmsg_multicast_allns+0x158/0x1b4 [compat]
[<ffffffc0004e0944>] genl_family_rcv_msg+0x258/0x2c0
[<ffffffc0004e09f4>] genl_rcv_msg+0x48/0x6c
[<ffffffc0004dfb50>] netlink_rcv_skb+0x5c/0xc4
[<ffffffc0004e06d8>] genl_rcv+0x34/0x48
[<ffffffc0004df570>] netlink_unicast+0x12c/0x1e0
[<ffffffc0004df9a4>] netlink_sendmsg+0x2bc/0x2dc
[<ffffffc00049a540>] sock_sendmsg+0x18/0x2c
[<ffffffc00049ab94>] ___sys_sendmsg+0x1bc/0x248
[<ffffffc00049ba24>] __sys_sendmsg+0x40/0x68
[<ffffffc00049ba5c>] SyS_sendmsg+0x10/0x20
[<ffffffc000085db0>] el0_svc_naked+0x24/0x28
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k_mac_get_ar_by_vdev_id() get protected under rcu lock
and unlock. peer association confirmation event get used this API
without rcu protection, so corrected it.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parse and store the out-of-band rates reported by the FW.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will start using ieee80211_tx_status_ext() so we do not need to track
tx rates inside a struct ieee80211_tx_info. It is currently not possible
to populate that struct with HE rate info anyhow.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns a few times (trimmed for brevity):
../drivers/net/wireless/ath/ath11k/debugfs_sta.c:185:7: warning:
variable 'rate_idx' is used uninitialized whenever 'if' condition is
false [-Wsometimes-uninitialized]
It is not wrong, rate_idx is only initialized in the first if block.
However, this is not necessarily an issue in practice because rate_idx
will only be used when initialized because
ath11k_accumulate_per_peer_tx_stats only uses rate_idx when flags is not
set to RATE_INFO_FLAGS_HE_MCS, RATE_INFO_FLAGS_VHT_MCS, or
RATE_INFO_FLAGS_MCS. Still, it is not good to stick uninitialized values
into another function so initialize it to zero to prevent any issues
down the line.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/832
Reported-by: ci_notify@linaro.org
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix warnings which were recently introduced:
drivers/net/wireless/ath/ath10k/ahb.c:462: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/ahb.c:470: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/sdio.c:697: space prohibited before that close parenthesis ')'
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Ftrace is one of the last W^X violators (after this only KLP is
left). These patches move it over to the generic text_poke()
interface and thereby get rid of this oddity. This requires a
surprising amount of surgery, by Peter Zijlstra.
- x86/AMD PMUs: add support for 'Large Increment per Cycle Events' to
count certain types of events that have a special, quirky hw ABI
(by Kim Phillips)
- kprobes fixes by Masami Hiramatsu
Lots of tooling updates as well, the following subcommands were
updated: annotate/report/top, c2c, clang, record, report/top TUI,
sched timehist, tests; plus updates were done to the gtk ui, libperf,
headers and the parser"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
perf/x86/amd: Add support for Large Increment per Cycle Events
perf/x86/amd: Constrain Large Increment per Cycle events
perf/x86/intel/rapl: Add Comet Lake support
tracing: Initialize ret in syscall_enter_define_fields()
perf header: Use last modification time for timestamp
perf c2c: Fix return type for histogram sorting comparision functions
perf beauty sockaddr: Fix augmented syscall format warning
perf/ui/gtk: Fix gtk2 build
perf ui gtk: Add missing zalloc object
perf tools: Use %define api.pure full instead of %pure-parser
libperf: Setup initial evlist::all_cpus value
perf report: Fix no libunwind compiled warning break s390 issue
perf tools: Support --prefix/--prefix-strip
perf report: Clarify in help that --children is default
tools build: Fix test-clang.cpp with Clang 8+
perf clang: Fix build with Clang 9
kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic
tools lib: Fix builds when glibc contains strlcpy()
perf report/top: Make 'e' visible in the help and make it toggle showing callchains
perf report/top: Do not offer annotation for symbols without samples
...
There is a spelling mistake in a wcn36xx_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ar5523_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the required USB ID for running SMCWUSBT-G2 wireless adapter (SMC
"EZ Connect g").
This device uses ar5523 chipset and requires firmware to be loaded. Even
though pid of the device is 4507, this patch adds it as 4506 so that
AR5523_DEVICE_UG macro can set the AR5523_FLAG_PRE_FIRMWARE flag for pid
4507.
Signed-off-by: Mert Dirik <mertdirik@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use device_get_match_data() here to simplify the code a bit.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some printks in here don't have newlines at the end, meaning the log
will be sort of hard to read. Add newlines.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two error paths where "ret" wasn't set. Also one error path
we set the error code to -EINVAL but we should just preserve the error
code from ath11k_hal_srng_get_entrysize(). That function only returns
-EINVAL so this doesn't change anything.
I removed the "ret = 0;" initializers so that hopefully GCC will be able
to detect these sorts of bugs in the future.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN to the list of known
fields. Not doing so will result in wireshark not calculating the
bitrate correctly.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the unlikely event that cap->supported_bands has neither
WMI_HOST_WLAN_2G_CAP set or WMI_HOST_WLAN_5G_CAP set then pointer
band is null and a null dereference occurs when assigning
band->n_iftype_data. Move the assignment to the if blocks to
avoid this. Cleans up static analysis warnings.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 9f056ed8ee ("ath11k: add HE support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds missing rx rate info stats like pilot evm,
per chain rssi, per user ul ppdu and mpdu counts and
ul ofdma rate info etc.
And add null checks for memory alloc failures.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the structure ts is not inititalized and ts.flags contains
garbage values from the stack. This is being passed into function
ath11k_dp_tx_status_parse that bit-wise or'ing in settings into the
ts.flags field. To avoid flags (and other fields) from containing
garbage, initialize the structure to zero before use.
Addresses-Coverity: ("Uninitialized scalar variable)"
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The channel info parameters are required by the firmware to process TxBf
parameters. Currently TxBf is passed prior to the channel info. This patch
moves TxBf setup after the channel setup.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch enables HE tlvs in ppdu stats for pktlog lite mode.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_ATH11K_DEBUGFS is disabled, but CONFIG_MAC80211_DEBUGFS
is turned on, the driver fails to build:
drivers/net/wireless/ath/ath11k/debugfs_sta.c: In function 'ath11k_dbg_sta_open_htt_peer_stats':
drivers/net/wireless/ath/ath11k/debugfs_sta.c:416:4: error: 'struct ath11k' has no member named 'debug'
ar->debug.htt_stats.stats_req = stats_req;
^~
It appears that just using the former symbol is sufficient here,
adding a Kconfig dependency takes care of the corner cases.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some targets ex: QCS404, SCM permissions for MSA region is
statically configured in TrustZone fw. Add SCM call disable option
for such targets to avoid duplicate permissions.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 76d164f582.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When simulate random transfer fail for sdio write and read, it crash
sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. it crash, the act len of ath10k_htc_hdr is higher than allocate len, it cause panic:
[ 99.723482] skbuff: skb_over_panic: text:00000000caa0f780 len:57013 put:57013 head:000000004116f24a data:0000000019ecb4dc tail:0xdef5 end:0x640 dev:<NULL>
[ 99.737697] ------------[ cut here ]------------
[ 99.742327] kernel BUG at /mnt/host/source/src/third_party/kernel/v4.19/net/core/skbuff.c:104!
[ 99.750937] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 99.831154] Process kworker/0:2 (pid: 151, stack limit = 0x00000000728010bf)
[ 99.838200] CPU: 0 PID: 151 Comm: kworker/0:2 Tainted: G W 4.19.85 #48
[ 99.846022] Hardware name: MediaTek krane sku0 board (DT)
[ 99.851429] Workqueue: events sdio_irq_work
[ 99.855614] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 99.860402] pc : skb_panic+0x64/0x68
[ 99.863974] lr : skb_panic+0x64/0x68
[ 99.867542] sp : ffffff8008833a90
[ 99.870850] x29: ffffff8008833ac0 x28: ffffffe52e337370
[ 99.876159] x27: ffffffe52e328a90 x26: 000000000000e0d0
[ 99.881469] x25: ffffffe52e336b60 x24: 000000000000deb5
[ 99.886779] x23: ffffffe52e340680 x22: ffffffe4efd47e00
[ 99.892088] x21: 000000000000deb5 x20: ffffffa516d85b4c
[ 99.897397] x19: ffffffa526928037 x18: 0000000000000000
[ 99.902706] x17: 000000000000003c x16: ffffffa5265b6c80
[ 99.908015] x15: 0000000000000006 x14: 3a76656420303436
[ 99.913325] x13: 0000000000029bf0 x12: 0000000000000000
[ 99.918634] x11: 0000000000000000 x10: 0000000000000000
[ 99.923943] x9 : a3b907e4b2783000 x8 : a3b907e4b2783000
[ 99.929253] x7 : 0000000000000000 x6 : ffffffa526f66d76
[ 99.934563] x5 : 0000000000000000 x4 : 0000000000000000
[ 99.939872] x3 : 000000000002a5ab x2 : ffffffe53feed918
[ 99.945182] x1 : ffffffe53fee4a08 x0 : 000000000000008e
[ 99.950491] Call trace:
[ 99.952937] skb_panic+0x64/0x68
[ 99.956165] skb_put+0x7c/0x84
[ 99.959224] ath10k_sdio_irq_handler+0x740/0xbb8 [ath10k_sdio]
[ 99.965055] process_sdio_pending_irqs+0x58/0x1a4
[ 99.969758] sdio_run_irqs+0x34/0x60
[ 99.973329] sdio_irq_work+0x1c/0x28
[ 99.974930] cros-ec-spi spi2.0: SPI transfer timed out
[ 99.976904] process_one_work+0x210/0x410
[ 99.976911] worker_thread+0x234/0x3dc
[ 99.976923] kthread+0x120/0x130
[ 99.982090] cros-ec-spi spi2.0: spi transfer failed: -110
[ 99.986054] ret_from_fork+0x10/0x18
[ 99.986063] Code: aa1403e2 2a1503e4 a90023e9 97e37d1a (d4210000)
[ 99.986068] ---[ end trace cb6d948c5a0fd6c7 ]---
[ 100.017250] Kernel panic - not syncing: Fatal exception
[ 100.018879] cros-ec-spi spi2.0: Command xfer error (err:-110)
[ 100.023659] SMP: stopping secondary CPUs
[ 100.023703] Kernel Offset: 0x251dc00000 from 0xffffff8008000000
[ 100.023707] CPU features: 0x0,2188200c
[ 100.023709] Memory Limit: none
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 8 bytes will be considered as ath10k_htc_hdr,
but actually the 8 bytes is not the ath10k_htc_hdr, so the act_len
from this ath10k_htc_hdr is not correct, if it is a big value, such
as 57013, it will trigger skb_panic.
Drop the skb with invalid length will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The description of ath10k_pci_dump_memory_sram() is inaccurate, an error
can never be returned, it is always the length. Update the comment to
reflect.
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/wil6210/main.c:765:1-14: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/txrx.c:1143:1-19: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1516:4-23: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1523:4-23: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1538:4-30: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1545:4-30: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath9k/ar9003_aic.c:409:2-12: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wil6210 driver locks a mutex in begin() ethtool_ops callback and
unlocks it in complete() so that all ethtool requests are serialized. This
is not going to work correctly with netlink interface; e.g. when ioctl
triggers a netlink notification, netlink code would call begin() again
while the mutex taken by ioctl code is still held by the same task.
Let's get rid of the begin() and complete() callbacks and move the mutex
locking into the remaining ethtool_ops handlers except get_drvinfo which
only copies strings that are not changing so that there is no need for
serialization.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The FIELD_SIZEOF() macro was redundant, and is being removed from the
kernel. Since commit c593642c8b ("treewide: Use sizeof_field() macro")
this is one of the last users of the old macro, so replace it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three of the WMI command handlers were not casting to the right data type.
Lets make the code consistent with the other handlers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
set_cqm_rssi_config() is used by the kernel to configure connection
quality monitor RSSI threshold.
wil6210 uses WMI_SET_LINK_MONITOR_CMDID to set the RSSI threshold to
FW which in turn reports RSSI threshold changes with
WMI_LINK_MONITOR_EVENTID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wil6210 AP has a separate ring for transmitting multicast packets,
multicast packets are transmitted without an ack from the receiver side.
Therefore, 802.11 spec defines some low MCS rates for multicat packets.
However, there is no guarantee that these packets were really received
and handled on the client side.
Some applications that rely on multicast packets, may prefer to
transmit these packets as a unicast to ensure reliability, and also
to ensure better performance with high MCS rates.
multicast to unicast is done by duplicating multicast packets to all
clients and changing the DA (multicast) to the MAC address of the
client.
see NL80211_CMD_SET_MULTICAST_TO_UNICAST for more info.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix incorrect definitions of MAC ID bits inside Rx status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ucode_debug memory region defined as 4K bytes. Fix this according to
Talyn device memory map.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
max_assoc_sta can receive values (from the user or from the FW)
that are higher than WIL6210_MAX_CID.
Verify that cid doesn't exceed the upper bound of WIL6210_MAX_CID.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some crash dump cases mem_lock is already taken, error
returns and crash dump copy fails.
In this case wait until mem_lock available instead of failing
the operation.
Also take the mem_lock for writing to prevent other threads from
altering the state of the device while collecting crash dump.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mem_lock is taken for the entire wil_reset().
Optimize this by taking mem_lock just before device is
being reset and release the lock after FW download.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump all the Rx status message on different errors to allow more
visibility of the case.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the signal stregth decays smoothly and physical connnection
is already gone and no deauth has arrived, the qcom soc is not
able to indicate neither WCN36XX_HAL_MISSED_BEACON_IND nor
WCN36XX_HAL_MISSED_BEACON_IND. It was noticed that such situation gets
even more reproducible, when the driver fails to enter bmps mode - which is
highly likely to occur. Thus, in order to provide proper disconnection
of the connected STA, let mac80211 handle it, instead of wcn3xx driver.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
storage interface descriptors to avoid submitting an URB to an invalid
endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The list iterator is always non-NULL so it doesn't need to be checked.
I also removed the unnecessary initializer because the list iterator is
always initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath11k_ce_alloc_ring() function returns error pointers on error, not
NULL. The rest of the driver assumes that "pipe->src_ring" is either
valid or NULL so this patch introduces a temporary varaible to avoid
leaving it as an error pointer.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The callers unlock this lock so this error path has a double unlock.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error handling when the call to ath11k_hal_srng_get_entrysize fails
leaks skb, fix this by returning via the err_free return path that will
ensure the skb is free'd.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable radioup is not uninitalized so it may contain a garbage
value and hence the detection of a radio that is not up is buggy.
Fix this by initializing it to zero.
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently a return path is leaking the previously allocate reg_info. Fix
this by exiting via the return path mem_free. Since the return value ret
is defaulted to 0, there is no need to re-assign ret to the 0 before
the goto.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
drivers/net/wireless/ath/ath11k/wmi.c:1827:23: warning: implicit
conversion from enumeration type 'enum wmi_scan_priority' to different
enumeration type 'enum scan_priority' [-Wenum-conversion]
arg->scan_priority = WMI_SCAN_PRIORITY_LOW;
~ ^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
wmi_scan_priority and scan_priority have the same values but the wmi one
has WMI prefixed to the names. Since that enum is already being used,
get rid of scan_priority and switch its one use to wmi_scan_priority to
fix this warning.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/808
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several spelling mistakes in warning and debug messages,
fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch sets the correct BA buffer size when we are in HE mode.
Without this change we are not able to receive 256 bitmapped BA frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code currently uses the wrong pdev id when enabling TWT. Fix this by
using the correct ones.
Fixes: e65a616f4e74 ("ath11k: add TWT support")
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function into dp_tx.c allows gcc to optimize the code better
and also avoid chace invalidates and context switches.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the current code does 4 memcpys for each completion frame.
1) duplicate the desc
2 + 3) inside kfifo insertion
4) kfifo remove
The code simply drops the kfifo and uses a trivial ring buffer. This
requires a single memcpy for insertion. There is no removal needed as
we can simply use the inserted data for processing. As the code runs
inside the NAPI context it is atomic and there is no need for most of
the locking.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the fields are only used by debugfs. Move the parsing of these
from the data hot path to the debugfs code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no point in zero'ing out the structure if we set all values in the
following line.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After applying this setting the TX performance issue of STA interfaces is
gone and we can see TX performance go up to ~900mbit on HE80.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a WMI call helper to set the powersave mode of a STA interface.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd+P4eAAoJEG4XJFUm622bnOQH/RHSFFQNjxfPboZoozKb0/mT
6YtrG+0K1z8E21Os2bd+s4aRJgq1oGKDocMie5y53M38qQ5N3FchzcGopNRCRy/a
gF1PzEqceOysbEtPOx4yI+c0Gfi7rS0SjEyf2XKGowXsoIZh4j+1xlWbF/JtHt6n
J901W1GW0ZUCHaP8KuZcbsS2nfdV8tFW2NQW3Xuhy+nOdBhNRL/lKSvlhZLCCAfY
f1eJrB0rAzQpCqw8Wuz2JzWsxBiTt+6Ucuzv4EkFVrt7Xnj00feghTKJkVDqa+fL
B9hTiiYh8sLGJkYHsZLDZIzAdOW8jmun1I+XFsjdl7ucLRYz6U8NL9jc6oIGK00=
=KJmM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some typo:
s/to to/to/
s/even/event/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The capabilities for the HE mesh are generated from the capabilities
reported by the fw. But the firmware only reports the overall capabilities
and not the one which are specific for mesh. Some of them (TWT, MU UL/DL,
TB PPDU, ...) require an infrastructure setup with a main STA (AP)
controlling the operations. This is not the case for mesh and thus these
capabilities are removed from the list of capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5 ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ath.git patches for v5.6. Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
Some sdio chips of rome QCA6174's regulatory domain code of EEPROM is
empty, then ath_is_world_regd will return false for this case, and
it will lead function __ath_reg_dyn_country not work, thus the regdomain
will not update for NL80211_REGDOM_SET_BY_COUNTRY_IE type, it result
ath10k set the same regdomain/reg_5ghz_ctl/reg_2ghz_ctl to firmware,
then the tx power will not changed with different regdomain's AP. The
regulatory domain code of EEPROM of some QCA6174 PCIE chip is 0x6c, it
means world wide regdomain, for this chip, it does not have the issue.
For empty reulatory domain code chip, set it to world regulatory domain
in functio ath_regd_sanitize, then it will fix the issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.
htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 224776520e ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently HTT_PPDU_STATS_TAG_USR_COMPLTN_ACK_BA_STATUS tag of PPDU stats
doesn't have valid success bytes info of management frames.
So skip update peer stats for management packets.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update tx duration in station info form PPDU stats
so that users can dump tx duration of the station.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Guard interval value which comes from VHT_SIG_A TLV has a mapping
where value 0 corresponds to LGI, 1 and 3 corresponds to SGI.
Value 3 which is SGI(0.4us) in VHT was incorrectly mapped to a GI
of 3.2us(only applicable in HE) resulting in incorrect rx GI stats.
Fixing the mapping.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove tail check to avoid last amsdu leak.
recycle skb in ppdu id wrap around case
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adverise MPDU start spacing as no restriction in ht capabilities,
Since IPQ8074 hw support all sorts of mpdu start spcing. With this
observed minor uplink performance improvement in lower data frame
size case with Veriwave clients.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the number of tx and rx chains properly on drv_set_antenna().
This will ensure the related ht/vht/he caps are properly recalculated
based on the tx/rx chains set.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add necessary peer assoc params in WMI debug message
while sending the peer assoc command to firmware
to aid in debugging.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
qmi firmware ready event start to initialize the core modules and
the sequence executed with mutex lock. In case of any failure
mutex should be unlocked otherwise it will hang during the recovery.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power
for traffic to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will
be based on the regulatory requirements. If the user given
transmit power is greater than the allowed tx power in the given
channel, then the firmware will use the maximum tx power in the
same channel.
Max and Min tx power values will depends on number of tx chain
masks. The allowed tx power range values are from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to
the default tx power for the station.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currenly in delba process calling ath11k_peer_rx_tid_delete() updates
reo with desc invalid and add tid queue to the flush list. If station
send data traffic without addba req and before tid flush, hw gives
those packets as invalid desc reo error. Since we are dropping these
invalid desc packets results in traffic stall.
This patch fix this issue by updating the reo queue with bawindow size 1
instead of tid removal in delba process.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing already stored first msdu data after the skb expand trigger
use_after_free, since first msdu got deleted. so do the descriptor copy
operation before the skb expand operation.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WMI_VDEV_SET_WMM_PARAMS commmand expects the txoplimit param in the units of
32 microseconds. convert the txop unit from 32 microseconds to absolute
microseconds leads to the higher burst values which is incorrect. so no need
to convert the txop unit from 32 microseconds to absolute microseconds.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes sending the pdev id(0,1,2 for mac0, mac1, mac2)
to FW in wmi cmd pktlog enable/disable.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio does not support wow, this patch is to enable it. When system enter
sleep state, if wowlan is enabled, then sdio chip will keep power if
platform support keep power, after resume, it will not need to re-load
firmware again.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change log level from warn to dbg level of mpdu status
of sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.
This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure the number of WBM_IDLE_LINK ring descriptors is power
of 2. This increases the number of descriptors to 32k from the
current ~18k to fix the target assert because of the shortage in
the descriptors in WBM_IDLE_LINK ring. Remove unnecessary
power of 2 calculation in ath11k_dp_link_desc_setup() as it is
not required after this change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV length was 0 for TLV tag 'WMI_TAG_ARRAY_STRUCT' causing
Q6 to crash when trying to configure pktlog filter via debugfs.
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
skb_panic is hit during msdu coalescing whenever
enough tailroom is not allocated based on the remaining
msdu length which is spread across in different rx buffers.
Compute the extra length for resizing the skb based on
the total msdu length and the msdu length of the first buffer.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove unused counter to avoid taking locks inorder to optimize
cpu load.
Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased
from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap
mode.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In conf_tx() mac operation callback, we are truncating the tx
params cw_min and cw_max due to lower data type cast. so modified
the data type of cwmin and cwmax to avoid the trucation issue.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch drops ath11k_hal_rx_parse_dst_ring_desc(). This function was
creating a huge amount of load, which lead to a signifcant latency delay
when processing data in the RX path.
Pegging the processing on a specific core and running perf --top we get
the following output when running HE80 at a fixed bandwidth of 1gbit.
with patch
19.19% [ath11k] [k] ath11k_dp_process_rx
5.02% [ath11k] [k] ath11k_dp_rx_tid_del_func
4.39% [kernel] [k] v7_dma_inv_range
4.15% [kernel] [k] __slab_alloc.constprop.1
4.03% [kernel] [k] dev_gro_receive
3.86% [kernel] [k] tcp_gro_receive
3.07% [ip_tables] [k] ipt_do_table
2.96% [kernel] [k] dma_cache_maint_page
without patch
21.64% [ath11k] [k] ath11k_hal_rx_parse_dst_ring_desc
10.80% [ath11k] [k] ath11k_dp_process_rx
3.77% [kernel] [k] v7_dma_inv_range
3.48% [kernel] [k] dev_gro_receive
3.32% [ath11k] [k] ath11k_dp_rx_tid_del_func
3.17% [mac80211] [k] ieee80211_rx_napi
2.70% [kernel] [k] dma_cache_maint_page
2.65% [mac80211] [k] ieee80211_sta_ps_transition
When removing the the bandwidth limit and rerunning the test we see an
overall throughput improvement of 3-400mbit when running 4x4 HE80.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that ath11k STA mode UL throughput is low.
This is due to packets delivered to FW from TCL instead of TQM.
TCL AST search fail causes packet delivered to FW, fix this by
properly configuring the TCL address search type and ast_hash.
STA UL throughput is improved 10times with 11AC AP.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current ath11k driver failed to parse
wmi_tlv_svc_rdy_ext_parse if there is change in
wmi_mac_phy_capabilities length with below error.
ath11k c000000.wifi1: failed to extract mac caps, idx :0
ath11k c000000.wifi1: failed to parse tlv -22
This is needed to get firmware version
WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handled the error case with proper resource cleanup and
moved the handling into a separate function from
ath11k_mac_sta_state.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Previous configuartion of htt stats sounding info and pdev cca stats
are invalid due to that getting time out error.
Changing htt stats sounding info value from 0xFF to 0x00 and htt pdev cca
stats from 0x10 to 0x00
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes the ath9k_pci_owl_loader to use the
same iowrite32 memory accessor that ath9k_pci is using
to communicate with the PCI(e) chip.
This will fix endian issues that came up during testing
with loaned AVM Fritz!Box 7360 (Lantiq MIPS SoCs + AR9287).
Fixes: 5a4f2040fd ("ath9k: add loader for AR92XX (and older) pci(e)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.
htc.c:803: ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881: ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trigger the WMI call en/disabling OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add target wait time wmi calls to the driver. En/disable the support
from when the bss_config changes. We ignore the cmd completion events.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add basic HE support to the driver. The sband_iftype data is generated from
the capabilities read from the FW.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unexecuted code while handling amsdu packets.
The same logic is done before calling ath11k_dp_rx_msdu_coalesce
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX rate stats for the retried packets for a station comes through
tx completion events. Assigning hw reported bandwidth information
directly to station's txrate bandwidth will cause below warning.
Fix this warning by converting the hw reported bandwidth to
mac80211 base bandwidth.
[ 134.758190] PC is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.765730] LR is at cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.875014] [<ffffffbffca8d708>] cfg80211_calculate_bitrate+0x1bc/0x214 [cfg80211]
[ 134.877192] [<ffffffbffcaa9704>] nl80211_put_sta_rate+0x54/0xf24 [cfg80211]
[ 134.884829] [<ffffffbffcaa9d48>] nl80211_put_sta_rate+0x698/0xf24 [cfg80211]
[ 134.891687] [<ffffffbffcaaa490>] nl80211_put_sta_rate+0xde0/0xf24 [cfg80211]
[ 134.898975] [<ffffffc0004de748>] genl_lock_dumpit+0x30/0x4c
[ 134.905998] [<ffffffc0004dc264>] netlink_dump+0xf4/0x248
[ 134.911291] [<ffffffc0004dc910>] __netlink_dump_start+0xe0/0x174
[ 134.916850] [<ffffffc0004df114>] genl_family_rcv_msg+0x130/0x2c0
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can regularly see the following message.
- "ath11k c000000.wifi1: failed to find the peer with peer_id 4"
This happens when the FW starts sending stats for the peer whilst the
peer is not fully associated. Convert this info message to a debug one.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Everytime a new peer gets associated, we see the following message in the log
- ath11k c000000.wifi1: Unknown eventid: 0x6017
Ignore this event for now. We probably need to handle the event properly when
we add OMI support.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 expects the definition of what HE rate info is available inside a
struct prepended to the skb.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
There is a check on the retry counter invalid_buf_id_retry that is always
false because invalid_buf_id_retry is initialized to zero on each iteration
of a while-loop. Fix this by initializing the retry counter before the
while-loop starts.
Addresses-Coverity: ("Logically dead code")
Fixes: b4a967b7d0 ("wil6210: reset buff id in status message after completion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 dBm
signal avg: -82 dBm
after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 [-84, -88] dBm
signal avg: -82 [-84, -87] dBm
For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.
rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128
rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128
after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.
iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
signal: -70 [-77, -72] dBm
signal avg: -69 [-78, -72] dBm
iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
signal: -47 [-55, -48, -87, -88] dBm
signal avg: -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
signal: -43 [-46, -45, -79, -84] dBm
signal avg: -43 [-46, -46, -82, -83] dBm
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the BDF download QMI message has the end field set to 1, it signals
the end of the transfer, and triggers the firmware to do a CRC check. The
BDFs for msm8998 devices fail this check, yet the firmware is happy to
still use the BDF. It appears that this error is not caught by the
downstream drive by concidence, therefore there are production devices
in the field where this issue needs to be handled otherwise we cannot
support wifi on them. So, attempt to detect this scenario as best we can
and treat it as non-fatal.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.
Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random
mac address for netdetect case.
iw command:
iw phy0 wowlan enable net-detect net-detect
randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30
freqs 2412 matches ssid foo.
After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41.
WCN3990, QCA9377, QCA6174 PCI also support this feature.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware with the build id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0.2-XXXX does
not support the QMI_WLFW_HOST_CAP_REQ_V01 message and will return the
QMI not supported error to the ath10k driver. Since not supporting this
message is not fatal to the firmware nor the ath10k driver, lets catch
this particular scenario and ignore it so that we can still bring up
wifi services successfully.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.
This will optimize the download firmware time cost.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.
The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unless we sleep for a while before transitioning the MSA memory to WLAN
the MPSS.AT.4.0.c2-01184-SDM845_GEN_PACK-1 firmware triggers a security
violation fairly reliably. Unforutnately recovering from this failure
always results in the entire system freezing.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 334f5b61a6.
This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:
err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219
Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded ret variable from ath5k_eeprom_read_spur_chans()
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change all files to add SPDX license identifiers and
remove license text.
This is only an administrative change, there is no change
in actual license or copyright for any file.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The `ar_usb` field of `ath10k_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath10k_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath10k_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath10k_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath10k_usb_alloc_urb_from_pipe` and
`ath10k_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref.
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Add driver tag to subject, fix build warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(kvalo: cherry picked from commit 1340cc631b in
wireless-drivers-next to wireless-drivers as this a frequently reported
regression)
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Regulatory rule defines in regd.c are used not only by ath9k but also
ath10k driver (haven't test other drivers) and thus should be
renamed from ATH9K* to ATH*.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The memory of ar->debug.tpc_stats_final is reallocated every debugfs
reading, it should be freed in ath10k_debug_destroy() for the last
allocation.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX)
or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds
access, so print a warning and reset to avoid memory corruption.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when pointer crash_data is null the present null check
will also check that crash_data->ramdump_buf is null and will cause
a null pointer dereference on crash_data. Fix this by using the ||
operator instead of &&.
Fixes: 3f14b73c38 ("ath10k: Enable MSA region dump support for WCN3990")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all data packets transmitted, host gets htt tx completion event. Some QCA9984
firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data
ack rssi values to host through htt event of data tx completion. Data ack rssi
values are valid if A0 bit is set in HTT rx message. So enable the feature also
for QCA9884.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[kvalo@codeaurora.org: improve commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
memcpy() in wmi_set_ie() and wmi_update_ft_ies() is called with
src == NULL and len == 0. This is an undefined behavior. Fix it
by checking "ie_len > 0" before the memcpy() calls.
As suggested by GCC documentation:
"The pointers passed to memmove (and similar functions in <string.h>)
must be non-null even when nbytes==0, so GCC can use that information
to remove the check after the memmove call." [1]
[1] https://gcc.gnu.org/gcc-4.9/porting_to.html
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memcpy() call with "idata == NULL && ilen == 0" results in undefined
behavior in ar5523_cmd(). For example, NULL is passed in callchain
"ar5523_stat_work() -> ar5523_cmd_write() -> ar5523_cmd()". This patch
adds ilen check before memcpy() call in ar5523_cmd() to prevent an
undefined behavior.
Cc: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
Cc: stable@vger.kernel.org
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rs_datalen is be16 so we need to convert it before printing.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, data variable in ar9003_hw_thermo_cal_apply() could be
uninitialized if ar9300_otp_read_word() will fail to read the value.
Initialize data variable with 0 to prevent an undefined behavior. This
will be enough to handle error case when ar9300_otp_read_word() fails.
Fixes: 80fe43f2bb ("ath9k_hw: Read and configure thermocal for AR9462")
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IRAM start address in coredump was wrong for QCA9984, QCA4019, QCA9888 and
QCA99x0.
Tested on: QCA9984, QCA4019
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Software version within WMI event ready message was displayed
in a not very useful decimal format. Change this info to be shown
in a hexadecimal format instead.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Displays lowest/highest supported channels for both 2ghz and 5ghz
bands as they're fetched within WMI service ready event.
These are shown in a frequency format.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdjLN3AAoJEG4XJFUm622bsBcH/1A/srmEN3bME86p9j0DS1Wb
A/8KPP88q9gczIDg+uZQCw1rTqHUrqkgbPxVCa64tKdPjqioRc9nW4CVhKh2OLTy
88Bwh/mJhxfh/+TTfYf397OsHr9NEVaFnEqjYeUxtyhRoZriUmAtKSd4/689czDP
AOdbkXShe8pUS+UvpizfpOHP28j4TbFOzcWn8qcGm1gqfuCHan+giaSw073vz+r4
fagOz470huyqCwx8LB21IzTCunox20W4IfN/G2AMoKx7tE9XbYr6kRR8vawffwm2
FVyhlnibkRQnRv77thg+zJZQ6UpJybsfM8Izpn1kTDFiRChNqvMtOKboz+IQOHg=
=4i7U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-09-26' of https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug code dereferences "skb" to print "skb->len" so we have to
print the message before we free "skb".
Fixes: f99fe49ff3 ("wil6210: add wil_netif_rx() helper function")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath10k_usb_hif_tx_sg the allocated urb should be released if
usb_submit_urb fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently, it has the basic feature of sdio tested success, so remove
it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a bunch of spelling mistakes in two ath drivers, fix
these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bmi_write32 and ath10k_bmi_read32 can fail. The fix
checks their statuses to avoid potential undefined behaviors.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current implementation of wmi init command,
there is no provision for the host driver to provide mem
chunks addresses with more than 32-bit, to the firmware.
WCN3990 is a 35-bit target and can accept mem chunks addresses
which are above 32-bit.
If firmware supports address range more than 32 bit, it
advertises the support by setting the WMI_SERVICE_EXTEND_ADDRESS
service. Based on this service fill the upper bits of paddr while
providing the mem chunks in the wmi init command.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSA memory region caries the hw descriptors information.
Dump MSA region in core dump as this is very helpful in debugging
hw issues.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMIC XO is the clock source for wifi rf clock in integrated wifi
chipset ex: WCN3990. Due to board layout errors XO frequency drifts
can cause wifi rf clock inaccuracy.
XO calibration test tree in Factory Test Mode is used to find the
best frequency offset(for example +/-2KHz )by programming XO trim
register. This ensure system clock stays within required 20 ppm
WLAN rf clock.
Retrieve the xo trim offset via system firmware (e.g., device tree),
especially in the case where the device doesn't have a useful EEPROM
on which to store the calibrated XO offset (e.g., for integrated Wifi).
Calibrated XO offset is sent to fw, which compensate the clock drift
by programing the XO trim register.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ath10k_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If 'sta->tdls' is false, no cleanup is executed, leading to memory/resource
leaks, e.g., 'arsta->tx_stats'. To fix this issue, perform cleanup before
go to the 'exit' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
driver sends QMI_WLFW_MSA_INFO_REQ_V01 QMI request to firmware
and in response expects range of addresses and size to be mapped.
Add condition to check whether addresses in response falls
under valid range otherwise return failure.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use ath10k_pci_soc_read32 / ath10k_pci_soc_write32 functions for
the rest of warm_reset functions. Until now these have been used
only for ath10k_pci_warm_reset_si0, but since they already exist
it makes sense to simplify code a bit.
Runtime tested with QCA9862.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bss_info_changed() handles various events from the upper layers. It
parses the changed bitfield and then configures the driver/firmware
accordingly. Each detected event is handled in a separate scope which is
independent of each other - but in the same function.
The commit f279294e9e ("ath10k: add support for configuring management
packet rate") changed this behavior by returning from this function
prematurely when some precondition was not fulfilled. All new event
handlers added after the BSS_CHANGED_BASIC_RATES event handler would then
also be skipped.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No frequency is currently specified for the single clock defined in the
snoc driver, so the clock wrappers reimplements the standard bulk API
provided by the clock framework. Change to this.
The single clock defined is marked as optional so this version of the
get API is used, but might need to be reconsidered in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator_get_optional() exists for cases where the driver needs do
behave differently depending on some regulator supply being present or
not, as we don't use this we can use the standard regulator_get() and
rely on its handling of unspecified regulators.
While the driver currently doesn't specify any loads the regulator
framework was updated last year to only account for load of enabled
regulators, so should the need appear it's better to apply load numbers
during initialization that dynamically.
With this the regulator wrappers have been reduced the become identical
to the standard bulk API provided by the regulator framework, so use
these instead of rolling our own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator operations is trying to set a voltage to a fixed value, by
giving some wiggle room. But some board designs specifies regulator
voltages outside this limited range. One such example is the Lenovo Yoga
C630, with vdd-3.3-ch0 in particular specified at 3.1V.
But consumers with fixed voltage requirements should just rely on the
board configuration to provide the power at the required level, so this
code should be removed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are special kinds of FW such as WMI only which
are used for testing, diagnostics and other specific
scenario.
Such FW is loaded during driver probe and the driver
disallows enabling any network interface, to avoid
operational issues.
In many cases it is used to debug early versions
of FW with new features, which sometimes fail
on startup.
Currently when such FW fails to load (for example,
because of init failure), the driver probe would fail
and shutdown the device making it difficult to debug
the early failure.
To fix this, ignore load failures in WMI only FW and
allow driver probe to succeed, making it possible to
continue and debug the FW load failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The short frame check in wil_sring_reap_rx_edma uses
skb->len which store the maximum frame length. Fix
this to use dmalen which is the actual length of
the received frame.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
writel_relaxed can be used in wil_debugfs_iomem_x32_set
since there is a wmb call immediately after.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Call cfg80211_inform_bss_frame_data to report cfg80211 on the
boottime_ns in order to prevent the scan results filtering due to
aging.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon driver rmmod, cancel_work_sync() can be invoked on
p2p.discovery_expired_work before this work struct was initialized.
This causes a WARN_ON with newer kernel version.
Add initialization of discovery_expired_work inside wil_vif_init().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMC is a hardware debug mechanism which allows capturing real time
debug data and stream it to host memory. The driver allocates memory
buffers and set them inside PMC ring of descriptors.
Add pmcring debugfs that application can use to read the binary
content of descriptors inside the PMC ring (cat pmcring).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move common part of wil_netif_rx_any into new helper function and add
support for non-gro receive using netif_rx_ni.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2 ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2 ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b2 ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_reg_rmw_single do not need return value to cope with different
cases. And change functon return type to void.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath6kl_htc_mbox_create(), when kzalloc() on line 2855 fails,
target->dev is assigned to NULL, and ath6kl_htc_mbox_cleanup(target) is
called on line 2885.
In ath6kl_htc_mbox_cleanup(), target->dev is used on line 2895:
ath6kl_hif_cleanup_scatter(target->dev->ar);
Thus, a null-pointer dereference may occur.
To fix this bug, kfree(target) is called and NULL is returned when
kzalloc() on line 2855 fails.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize acktimeout to the maximum configurable value in
ath_dynack_reset in order to not disconnect long distance static links
enabling dynack and even to take care of possible errors configuring
a static timeout. Moreover initialize station timeout value to the current
acktimeout value
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compute maximum configurable ackimeout/ctstimeout according to channel
width (clockrate)
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add compute timeout to last computation timestamp in
ath_dynack_reset in order to not run ath_dynack_compute_ackto
immediately
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts
timeouts and remove duplicated code
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.
Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.
Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/carl9170/usb.c: In function carl9170_usb_disconnect:
drivers/net/wireless/ath/carl9170/usb.c:1110:21:
warning: variable udev set but not used [-Wunused-but-set-variable]
It is not use since commit feb09b2933 ("carl9170:
fix misuse of device driver API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A null pointer would be passed to a call of the function “kfree”
directly after a call of the function “kcalloc” failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several occasions where a negative cid value is passed
into wil_cid_valid and this is converted into a u8 causing the
range check of cid >= 0 to always succeed. Fix this by making
the cid argument an int to handle any -ve error value of cid.
An example of this behaviour is in wil_cfg80211_dump_station,
where cid is assigned -ENOENT if the call to wil_find_cid_by_idx
fails, and this -ve value is passed to wil_cid_valid. I believe
that the conversion of -ENOENT to the u8 value 254 which is
greater than wil->max_assoc_sta causes wil_find_cid_by_idx to
currently work fine, but I think is by luck and not the
intended behaviour.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As clang points out, the vht_pfr is assigned to a struct member
without being initialized in one case:
drivers/net/wireless/ath/ath10k/mac.c:7528:7: error: variable 'vht_pfr' is used uninitialized whenever 'if' condition
is false [-Werror,-Wsometimes-uninitialized]
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7551:20: note: uninitialized use occurs here
arvif->vht_pfr = vht_pfr;
^~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7528:3: note: remove the 'if' if its condition is always true
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7483:12: note: initialize the variable 'vht_pfr' to silence this warning
u8 vht_pfr;
Add an explicit but probably incorrect initialization here.
I suspect we want a better fix here, but chose this approach to
illustrate the issue.
Fixes: 8b97b055dc ("ath10k: fix failure to set multiple fixed rate")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:926: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
drivers/net/wireless/ath/ath10k/pci.c:1072: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
While at it, also remove unnecessary initialisation of data_buf variable in both cases.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/swap.c:110: Possible unnecessary 'out of memory' message
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The workqueue need to flush and destory while remove sdio module,
otherwise it will have thread which is not destory after remove
sdio modules.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k will receive some message with invalid peer id from firmware.
reason is:
There are incoming frames to MAC hardware that NOT find relative
address search table, then peer id is invalid set by MAC hardware,
it is hardware's logic, so fix it in ath10k will be more convenient.
log:
ath10k_sdio mmc1:0001:1: Got RX ind from invalid peer: 65535
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the memory allocated for qmi handle is
not being freed during de-init which leads to memory leak.
Free the allocated qmi memory in qmi deinit
to avoid memory leak.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: fda6fee0001e ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It report error message while suspend/resume test.
dmesg log:
[ 150.749962] ath10k_sdio mmc1:0001:1: hif read32 not supported
[ 150.755728] ath10k_sdio mmc1:0001:1: failed to set coverage class: expected integer microsecond value in register
Reason is sdio chip does not support set_coverage_class as well as
pcie chip, remove the set_coverage_class handler will avoid it.
callstack of the error message:
OUTLINED_FUNCTION_6+0xc/0x14 [ath10k_core]
ath10k_mac_op_set_coverage_class+0x2c/0x40 [ath10k_core]
ieee80211_reconfig+0x5d0/0x108c [mac80211]
ieee80211_resume+0x34/0x6c [mac80211]
wiphy_resume+0xbc/0x13c [cfg80211]
dpm_run_callback+0xa4/0x168
device_resume+0x1d4/0x200
async_resume+0x1c/0x34
async_run_entry_fn+0x48/0xf8
process_one_work+0x178/0x2f8
worker_thread+0x1d8/0x2cc
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
the error log will not happen after this patch applied.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change fixes a rare race condition of handling WMI events after
wmi_call expires.
wmi_recv_cmd immediately handles an event when reply_buf is defined and
a wmi_call is waiting for the event.
However, in case the wmi_call has already timed-out, there will be no
waiting/running wmi_call and the event will be queued in WMI queue and
will be handled later in wmi_event_handle.
Meanwhile, a new similar wmi_call for the same command and event may
be issued. In this case, when handling the queued event we got WARN_ON
printed.
Fixing this case as a valid timeout and drop the unexpected event.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace all wmi_call timeouts that are less than 100 msec to use
WIL_WMI_CALL_GENERAL_TO_MS (100 msec) as a default. Some of the
current wmi_call timeouts are too short and fails to receive its
waiting events.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Base-band chips support multi RFs chips. Add support for reading
multiple RFs temperature via debugfs.
Signed-off-by: Tzahi Sabo <stzahi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set max_msdu_size in WMI_BCAST_DESC_RING_ADD_CMD to allow FW
to optimize the buffers allocation for bcast packets.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of wil_find_cid()/wil_find_cid_by_idx() is
validated with the lower boundary value.
Check the upper boundary value as well.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clear the FW and ucode log address on device initialization to allow
user space app identify when the address was set by FW/ucode and it can
start read.
Signed-off-by: Tzahi Sabo <stzahi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace sprintf with snprintf which checks the destination buffer
size.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RBUFCAP support added in FW.
The RBUFCAP feature is amendment to the block ack mechanism to
prevent overloading of the recipient’s memory space, which may
happen in case the link speed is higher than STA’s capability
to process or consume incoming data.
The block ack policy (ba_policy) is now controlled by FW so driver
should ignore this field.
Add new debugfs "rbufcap" to configure RBUFCAP.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver updates Tx status ring HW tail only after it finishes
processing the whole status ring, while the HW is still transmitting
from other transmit rings. This can cause back-pressure on HW if
no status entries are available.
Update HW tail of Tx status ring without waiting for the end of the
processing to help feeding back the HW with status entries and to allow
additional packet transmission.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With multiple clients and in high throughput scenarios, Tx status ring
can get full and become a bottleneck in Tx transmission.
Set the default Tx status ring size order to 13, previous value was 12.
This will double the status ring size from 4K entries to 8K entries.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the FW is reset on every interface type change, because
of various FW bugs.
FW reset is not required when switching from STA to P2P client, hence
can be skipped.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch removes the error branch for (queue > ar->hw->queues).
It is no longer needed anymore as the "queue" value is validated by
cfg80211's parse_txq_params() before the driver code gets called.
Some background:
In the old days (linux 2.6 and early 3.x), the parse_txq_params()
function did not verify the "queue" value. That's why these drivers
had to do it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 3c0efb745a ("ath9k: discard undersized packets")
the lower bound of RX packets was set to 10 (min ACK size) to
filter those that would otherwise be treated as invalid at
mac80211.
Alas, short radar pulses are reported as PHY_ERROR frames
with length set to 3. Therefore their detection stopped
working after that commit.
NOTE: ath9k drivers built thereafter will not pass DFS
certification.
This extends the criteria for short packets to explicitly
handle PHY_ERROR frames.
Fixes: 3c0efb745a ("ath9k: discard undersized packets")
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power for traffic
to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will be based
on the regulatory requirements. If the user given transmit power is greater
than the allowed tx power in the given channel, then the firmware will use
the maximum tx power in the same channel.
Max and Min tx power values will depends on no of tx chain masks,
for QCA9984 allowed tx power range values from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to the default
tx power for the station.
Tested Hardware : QCA9984
Tested Firmware : 10.4-3.9.0.2-00046
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "WARNING" string confuses syzbot, which thinks it found
a crash [1].
Change the string to avoid such problem.
[1] https://lkml.org/lkml/2019/5/9/243
Reported-by: syzbot+c1b25598aa60dcd47e78@syzkaller.appspotmail.com
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For QCA988X target, pktlog gives details of the tx bitrate
which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts
in target to host CE pipe, which can impact more CPU usage
for targets ex:WCN3990 and also not required for all other
platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e8123bb74c ("ath10k: add per peer tx stats support for 10.2.4")
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name for UTF mode of SDIO has changed from utf-2.bin to
utf-sdio-2.bin, so it need to change in ath10k, otherwise it will
fail for UTF mode.
After change the name in ath10k, it will success for UTF mode of
SDIO/USB.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The command to simulate firmware crash:
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
It will send WMI_FORCE_FW_HANG_ASSERT to firmware, then it will trigger
CPU interrupt status register for SDIO chip, ath10k driver need to
configure it while enable SDIO interrupt, otherwise ath10k driver will
not get the assert error info.
After this change, it will success for simulate firmware crash.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_dbg() is called in ath10k_process_rx() with huge set of arguments
which is causing CPU overhead even when debug_mask is not set.
Good improvement was observed in the receive side performance when call
to ath10k_dbg() is avoided in the RX path.
Since currently all debug messages are sent via tracing infrastructure,
we cannot entirely avoid calling ath10k_dbg. Therefore, call to
ath10k_dbg() is made conditional based on tracing config in the driver.
Trasmit performance remains unchanged with this patch; below are some
experimental results with this patch and tracing disabled.
mesh mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP 840Mbps 76.53% 960Mbps 78.14%
UDP 1030Mbps 74.58% 1132Mbps 74.31%
Infra mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP Rx 1241Mbps 80.89% 1270Mbps 73.50%
UDP Rx 1433Mbps 81.77% 1472Mbps 72.80%
Tested platform : IPQ8064
hardware used : QCA9984
firmware ver : ver 10.4-3.5.3-00057
Signed-off-by: Kan Yan <kyan@chromium.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this op, it will not be possible to configure aggregation for
high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order to make the *htt_h2t_aggr_cfg_msg* op align better
with the rest of the htt ops (whom all have inline wrappers).
It also adds support for the case when the op is missing (function
pointer is NULL).
As a result of this, the name of the 32 bit implementation in htt_tx.c
was changed and the function was made static.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000435.742096485@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ifa_list is protected by rcu, yet code doesn't reflect this.
Add the __rcu annotations and fix up all places that are now reported by
sparse.
I've done this in the same commit to not add intermediate patches that
result in new warnings.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program see the file copying if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.384204437@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
tx_stats will be freed and set to NULL before debugfs_sta node is
removed in station disconnetion process. So if read the debugfs_sta
node there may be NULL pointer error. Add check for tx_stats before
use it to resove this issue.
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some SDIO chip, the peer id is 65535 for MPDU with error status,
then test_bit will trigger buffer overflow for peer's memory, if kasan
enabled, it will report error.
Reason is when station is in disconnecting status, firmware do not delete
the peer info since it not disconnected completely, meanwhile some AP will
still send data packet to station, then hardware will receive the packet
and send to firmware, firmware's logic will report peer id of 65535 for
MPDU with error status.
Add check for overflow the size of peer's peer_ids will avoid the buffer
overflow access.
Call trace of kasan:
dump_backtrace+0x0/0x2ec
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x250/0x26c
__asan_report_load8_noabort+0x20/0x2c
ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core]
ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x370
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x508/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware advertises the service WMI_TLV_SERVICE_MESH_11S
for mesh 11s. Map this wmi tlv service to enable mesh 11s
for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a disparity in wmi and wmi tlv vdev subtype
enum for WMI_VDEV_SUBTYPE_MESH_11S.
Add different enum for wmi tlv vdev subtype to support
vdev of subtype mesh 11s for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For SDIO chip, it does not have HTT connect step in boot phase of UTF
mode, so it does not need the swap configuration for UTF mode, otherwise
it will trigger UTF load fail. For normal mode, it is swap between HTT
and WMI, for UTF mode, it does not have HTT, so it can not swap between
HTT and WMI.
Disable swap mail box for UTF mode will let UTF mode load success.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum value for WMI_TLV_STAT_PDEV, WMI_TLV_STAT_VDEV
and WMI_TLV_STAT_PEER is wrong, due to which the vdev stats
are not received from firmware in wmi_update_stats event.
Fix the enum values for above stats to receive all stats
from firmware in WMI_TLV_UPDATE_STATS_EVENTID.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: f40a307eb9 ("ath10k: Fill rx duration for each peer in fw_stats for WCN3990)
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*ce_hdr) + CE_COUNT * sizeof(ce_hdr->entries[0])
with:
struct_size(ce_hdr, entries, CE_COUNT)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*rx) + (sizeof(struct htt_rx_indication_mpdu_range) * num_mpdu_ranges)
to :
struct_size(rx, mpdu_ranges, num_mpdu_ranges)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently instant rx_duration always fetching as zero
in fw_stats debugfs entry if extended peer stats event
supports.
This patch updates instant rx_duration in fw_stats entry
based on extended peer stats and maintaining backward
compatibility for 10.2/10.x.
Tested HW: QCA9984.
Tested FW: 10.4-3.6.0.1-00004.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In tx_stats debugfs, txrate->flags may contain multiple bits. For
example, RATE_INFO_FLAGS_SHORT_GI could be set, and tx stats bytes
and packets will be not updated correctly.
Fix this issue by using bit operation to check txrate->flags.
Tested HW: QCA9984
Tested Firmware: 10.4-3.9.0.1-00007
Signed-off-by: Brandon Huang <yanghuan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE4 is host to target HTT tx pipe, tx completion are not served
on time when CPU is loaded and this cause ce src ring full condition
due to less no of src buffer entries.
To mitigate the issue increase CE4 src buffer entries to 2048.
Testing:
Tested on QCS404 platform(WCN3990 HW)
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Board id and fw version is not printed by default in qmi
cap response message. Move board id and fw version logging
to info level for default logging.
[ 34.005399] ath10k_snoc a000000.wifi: qmi chip_id 0x30b chip_family 0x4001 board_id 0xff soc_id 0x40070000
[ 34.005432] ath10k_snoc a000000.wifi: qmi fw_version 0x3106836b fw_build_timestamp 2019-02-13 10:24 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.1-00875-QCAHLSWMTPL-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset HTT stats helps to get the aggregated HTT stats via
tracing and also we can clear the accumulated HTT stats with
this debugfs file.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extended the bit mask value of the HTT stats to get the Mu-MIMO
related stats via tracing.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Talyn the HW is responsible for power management enter / exit
flow, hence the deep sleep exit latency is significantly shorter than
in Sparrow.
In such a case HALP feature, that is meant to prevent long PCIe blocking
accesses, is no longer needed and can be removed for Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure rx_buff_mgmt is initialized before accessing it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When MISC interrupt is triggered due to HALP bit, in parallel
to mbox events handling by the MISC threaded IRQ, new mbox
interrupt can be missed in the following scenario:
1. MISC ICR is read in the IRQ handler
2. Threaded IRQ is completed and all MISC interrupts are unmasked
3. mbox interrupt is set by FW
4. HALP is masked
The mbox interrupt in step 3 can be missed due to constant high level
of ICM.
Masking all MISC IRQs instead of masking only HALP bit in step 4
will guarantee that ICM will drop to 0 and interrupt will be triggered
once MISC interrupts will be unmasked.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Save the parameter of max_assoc_sta per device.
On fw_ready event calculate the max_assoc_sta and save it per device,
do not overwrite the max_assoc_sta module param.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add printing of hwhead as part of desc ring and status ring debugfs.
Validate wil->rx_buff_mgmt and ring->ctx arrays before accessing them.
Dump Tx descriptor content even when it indicates invalid buff_id.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current board file loading procedure assumes that the board file
includes only one section.
New board files can include multiple sections.
Add the ability to read multiple addresses and max size from FW
file and load multiple sections from the board file into those
addresses.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add logging of the platform capabilities after retrieving it from the
platform driver.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_desc is defined in __wil_tx_vring_tso() and may not be set in
case len is 0, verify _desc is set.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt is set in ICM (ICR & ~IMV) rising trigger.
As the driver masks the IRQ after clearing it, there can
be a race where an additional spurious interrupt is triggered
when the driver unmask the IRQ.
This can happen in case HW triggers an interrupt after the clear
and before the mask.
To prevent the second spurious interrupt the driver needs to mask the
IRQ before reading and clearing it.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang fails to eliminate some dead code with always-taken branches
when CONFIG_PROFILE_ANNOTATED_BRANCHES is set, leading to a false-positive
warning:
drivers/net/wireless/ath/carl9170/mac.c:522:3: error: variable 'power' is used uninitialized whenever 'if' condition is
false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
Change both instances of BUG_ON(1) in carl9170 to the simpler BUG()
to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:
enum gro_result {
GRO_MERGED,
GRO_MERGED_FREE,
GRO_HELD,
GRO_NORMAL,
GRO_DROP,
GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;
In case *rc* evaluates to 5, we end up having an out-of-bounds read
at drivers/net/wireless/ath/wil6210/txrx.c:821:
wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n",
len, gro_res_str[rc]);
Fix this by adding element "GRO_CONSUMED" to array gro_res_str.
Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
Fixes: 194b482b50 ("wil6210: Debug print GRO Rx result")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Increase pulse width range from 1-2usec to 0-4usec.
During data traffic HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the success rate.
Tested ath10k hw and fw:
* QCA9888(10.4-3.5.1-00052)
* QCA4019(10.4-3.2.1.1-00017)
* QCA9984(10.4-3.6-00104)
* QCA988X(10.2.4-1.0-00041)
Tested ath9k hw: AR9300
Tested-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9330, AR9485, AR9531, AR9550, AR9561 and AR9565 all use same
channel set register configuration which allows for small code
size reduction.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove duplicate NO_CTL that is just 2 lines below.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_count_frames':
drivers/net/wireless/ath/ath9k/xmit.c:413:25: warning: variable 'fi' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_complete_aggr':
drivers/net/wireless/ath/ath9k/xmit.c:449:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_start':
drivers/net/wireless/ath/ath9k/xmit.c:2274:18: warning: variable 'avp' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c:2269:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]
These variables are not used any more
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath9k driver uses as maximum allowed txpower the constant
MAX_RATE_POWER. It is used to set a maximum txpower limit for the PHY
(which is combined txpower) and also the maximum txpower for per chain
rates. Its value 63 is derived from the maximum number the registers can
store for the per chain txpower.
The max txpower a user can set because of this is 31 dBm (floor(63 / 2)).
This also means that a device with multiple tx chains is even limited
further:
* 1 chain: 31 dBm per chain
* 2 chains: 28 dBm per chain
* 3 chains: 26 dBm per chain
This combined txpower limit of 31 dBm becomes even more problematic when
some extra antenna gain is set in the EEPROM. A high power device is then
no longer able to reach its potential limits.
Instead the code dealing with the combined txpower must use a higher limit
than 63 and only the code dealing with the per chain txpower have to use
the limit of 63. Since the antenna gain can be quite large and 8 bit
variables are often used in ath9k for txpower, a large, divisible by two
number like 254 is a good choice for this new limit.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As already noted a comment in ath_tx_complete_aggr(), the hardware will
occasionally send a TX status with the wrong tid number. If we trust the
value, airtime usage will be reported to the wrong AC, which can cause the
deficit on that AC to become very low, blocking subsequent attempts to
transmit.
To fix this, account airtime usage to the TID number from the original skb,
instead of the one in the hardware TX status report.
Reported-by: Miguel Catalan Cid <miguel.catalan@i2cat.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The check on status not being zero is redundant as previous code
paths that set status to an error value break out of the while
loop and hence status is never non-zero at the check. Remove
this redundant code.
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements. We need to add a couple bounds
checks to prevent array overflows.
I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.
Fixes: bdcd817079 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*ev) + ev->num_neighbors * sizeof(struct wmi_neighbor_info)
with:
struct_size(ev, neighbor, ev->num_neighbors)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*tbl) + num_entries * sizeof(struct wmi_bss_roam_info)
to :
struct_size(tbl, info, num_entries)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.
Also tone down the warning about SDIO being not ready yet.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.
Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not likely, the bundle allocation might fail.
Add proper error check and warning print.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().
To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.
call stack of use-after-free:
dump_backtrace+0x0/0x2d8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x258/0x274
__asan_report_load4_noabort+0x20/0x28
skb_pull+0xbc/0x114
ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core]
ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio]
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Allocated by one task:
kasan_kmalloc+0xa0/0x13c
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x144/0x208
__alloc_skb+0xec/0x394
alloc_skb_with_frags+0x8c/0x374
sock_alloc_send_pskb+0x520/0x5d4
sock_alloc_send_skb+0x40/0x50
__ip_append_data+0xf5c/0x1858
ip_make_skb+0x194/0x1d4
udp_sendmsg+0xf24/0x1ab8
inet_sendmsg+0x1b0/0x2e0
sock_sendmsg+0x88/0xa0
__sys_sendto+0x220/0x3a8
__arm64_sys_sendto+0x78/0x80
el0_svc_common+0x120/0x1e0
el0_svc_compat_handler+0x64/0x80
el0_svc_compat+0x8/0x18
Freed by another task:
__kasan_slab_free+0x120/0x1d4
kasan_slab_free+0x10/0x1c
kmem_cache_free+0x74/0x504
kfree_skbmem+0x88/0xc8
__kfree_skb+0x24/0x2c
consume_skb+0x114/0x18c
__ieee80211_tx_status+0xb7c/0xf60 [mac80211]
ieee80211_tx_status+0x224/0x270 [mac80211]
ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core]
ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x358
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Reported-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.
Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add an error print-out in case FW and board files load fails,
as such an error is not printed on all failures and user may
not understand why the interface up operations didn't succeed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since DR bit and buffer id are written in different dwords of
the status message, the DR bit can already be set to 1 while the
buffer id is not updated yet.
Resetting the buffer id in the status message will allow the driver
to identify such cases and re-read the status message until the buffer
id is written by HW.
In case DR bit is set but buffer id is zero, need to read the status
message again, until a valid id is identified.
In addition to that, move the completed buffer id to the tail of the
free list to prevent its immediate reuse in the upcoming refill.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver needs to expose RGF_USER_USAGE_2 register that contains
the offset of the ucode logging table.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to access control RGF_CAF_ICR cannot be accessed by host.
Such an access will cause device AHB logger to halt and it will not
capture future AHB fault if there is any.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions that send management TX frame have 3 possible
results: success and other side acknowledged receive (ACK=1),
success and other side did not acknowledge receive(ACK=0) and
failure to send the frame. The current implementation
incorrectly reports the ACK=0 case as failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the rx packet checksum of received packet according to edma
HW spec:
No need to calculate checksum in the following cases:
L4_status=0 and L3_status=0 - No L3 and no L4 known protocols found
L4_status=0 and L3_status=1 - L3 was found, and checksum check passed.
No known L4 protocol was found.
L4_status=1 - L4 was found, and checksum check passed.
Recalculate checksum in the following cases:
L4_status=3 and L3_status=1 - It means that L3 protocol was found,
and checksum passed, but L4 checksum failed.
L4_status=3 and L3_status=2 - Both L3 and L4 checksum check failed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
edma_rx_swtail dma memory free is missing.
Add this part of Rx desc ring free.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In addition to existing MAC address field in OTP, new field added for
OEM MAC address.
wil6210 gives precedence to the new OEM MAC address and will use it if
its valid.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check that the mid is valid and that it does not exceed the memory
size allocated to vifs array.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update max MCS to 15, which is supported by Talyn-MB.
This will allow collecting statistics on number of RX packets
in higher MCS.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Sparrow, FW might sleep long time due to T_Power_On calculation
in slow clock, so T_Power_On was set to zero to shorten the L1SS
wake-up time.
In Talyn-MB the L1SS wake-up procedure is handled by the PMU (HW),
hence T_Power_On calculation is accurate and should not be forced
to zero.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case there are connected stations, FW needs to disconnect
them before handling PCP stop. This flow can take several
seconds.
Increasing PCP stop timeout to 5 seconds to allow that.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing some of the memory of the device while the device is
resetting or suspending may cause unexpected error as the HW is still
not in a stable state. Prevent this access to guarantee successful
read/write memory operations.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having functions to access 802.3 header
members, source and destination addresses.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In AP mode with multiple clients, driver stops net queue
(netif_tx_stop_queue) upon first ring (serving specific client)
becoming full. This can have negative effect on transmission to
other clients which may still have room in their corresponding rings.
Implement new policy in which stop/wake net queue are not used. In
case there is no room in the ring for a transmitted packet, drop the
packet.
New policy can be helpful to debug performance issues, to guarantee
maximum utilization of net queues.
New policy is disabled by default and can be enabled by debugfs:
echo 1 > drop_if_ring_full
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 5.1. Major changes:
ath10k
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having
WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices like the Linksys EA6350v3, whose
country codes are not present in the original list. Without this patch,
all devices whose manufacturer programmed any of these code in their
EEPROM will not work.
The values for CTRY_UNITED_STATES2 and CTRY_UNITED_STATES3 were taken
from a post by Sven Eckelmann <sven.eckelmann@openmesh.com>:
<http://lists.infradead.org/pipermail/ath10k/2017-August/010014.html>
Signed-off-by: Oever Gonzalez <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...) In this case,
if snprintf would have written more characters than what the buffer
size (SIZE) is, then size will end up larger than SIZE. In later uses
of snprintf, SIZE - size will result in a negative number, leading to
problems. Note that size might already be too large by using size =
snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to
user space, then it will potentially allow for a buffer overflow and
information disclosure when size is greater than SIZE. When the size is
used to index the buffer directly, we can have memory corruption. This
also means when size = snprintf... is used, it may also cause problems
since size may become large. Copying to userspace is mitigated by the
HARDENED_USERCOPY kernel configuration.
The solution to these issues is to use scnprintf which returns the number
of characters actually written to the buffer, so the size variable will
never exceed SIZE.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_wmi_cmd_send could fail, so let's return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_of_init() function[0] was initially written on the assumption that
if someone had an explicit ath9k OF node that "there must be something
wrong, why would someone add an OF node if everything is fine"[1]
(Quoting Martin Blumenstingl <martin.blumenstingl@googlemail.com>)
"it turns out it's not that simple. with your requirements I'm now aware
of two use-cases where the current code in ath9k_of_init() doesn't work
without modifications"[1]
The "your requirements" Martin speaks of is the result of the fact that I
have a device (PowerCloud Systems CR5000) has some kind of default - not
unique mac address - set and requires to set the correct MAC address via
mac-address devicetree property, however:
"some cards come with a physical EEPROM chip [or OTP] so "qca,no-eeprom"
should not be set (your use-case). in this case AH_USE_EEPROM should be
set (which is the default when there is no OF node)"[1]
The other use case is:
the firmware on some PowerMac G5 seems to add a OF node for the ath9k
card automatically. depending on the EEPROM on the card AH_NO_EEP_SWAP
should be unset (which is the default when there is no OF node). see [3]
After this patch to ath9k_of_init() the new behavior will be:
if there's no OF node then everything is the same as before
if there's an empty OF node then ath9k will use the hardware EEPROM
(before ath9k would fail to initialize because no EEPROM data was
provided by userspace)
if there's an OF node with only a MAC address then ath9k will use
the MAC address and the hardware EEPROM (see the case above)
with "qca,no-eeprom" EEPROM data from userspace will be requested.
the behavior here will not change
[1]
Martin provides additional background on EEPROM swapping[1].
Thanks to Christian Lamparter <chunkeey@gmail.com> for all his help on
troubleshooting this issue and the basis for this patch.
[0]https://elixir.bootlin.com/linux/v4.20-rc7/source/drivers/net/wireless/ath/ath9k/init.c#L615
[1]https://github.com/openwrt/openwrt/pull/1645#issuecomment-448027058
[2]https://github.com/openwrt/openwrt/pull/1613
[3]https://patchwork.kernel.org/patch/10241731/
Fixes: 138b41253d ("ath9k: parse the device configuration from an OF node")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not an unexpected condition, so we don't need to be shouting to the
world about it.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22 ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes: dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prevent a namespace conflict as in following patches as skbuff.h will
include the crypto API.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 may call us with vif == NULL, if the station is not currently
active (e.g., not associated). It is trivially easy to reproduce a crash
by suspending the system when not connected to an AP:
[ 65.533934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
[ 65.574521] pc : ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.574538] lr : __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.599680] Process kworker/u12:1 (pid: 57, stack limit = 0x(____ptrval____))
[ 65.599682] Call trace:
[ 65.599695] ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.642064] __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.642079] ieee80211_flush_queues+0x34/0x40 [mac80211]
[ 65.642095] __ieee80211_suspend+0xfc/0x47c [mac80211]
[ 65.658611] ieee80211_suspend+0x30/0x3c [mac80211]
[ 65.658627] wiphy_suspend+0x15c/0x3a8 [cfg80211]
[ 65.672810] dpm_run_callback+0xf0/0x1f0
[ 65.672814] __device_suspend+0x3ac/0x4f8
[ 65.672819] async_suspend+0x34/0xbc
[ 65.684096] async_run_entry_fn+0x54/0x104
[ 65.684099] worker_thread+0x4cc/0x72c
[ 65.684102] kthread+0x134/0x13c
[ 65.684105] ret_from_fork+0x10/0x18
Fixes: 9de4162f09 ("ath10k: add peer flush in ath10k_flush for STATION")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We tried to revert commit d9c52fd17c ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8 ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove experimental tag from dynack Kconfig entry since it has
been tested on outdoor 25Km links
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to make propagation time estimation faster,
use current sample as ewma output value during 'late ack'
tracking
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check da->enabled flag first in ath_dynack_sample_tx_ts and
ath_dynack_sample_ack_ts routines in order to avoid useless
processing
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move debug log in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts
after timestamp buffer head/tail increments in order to make debugging
more user friendly
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Not all devices using this driver are backed by a PCI device, so it's
not fair to assume 'to_pci_dev()' is valid. Fortunately, we only were
using this to convert straight back to a bare 'device', which means we
were only doing no-op pointer arithmetic, and not actually accessing
potentially out-of-bounds memory. But this is still bad practice.
Just use 'ar->dev' directly, since that's really all we're looking for.
Fixes: 209b2a68de ("ath10k: add platform regulatory domain support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 2ea9f12cef ("ath10k: add new cipher suite support") added a new
n_cipher_suites HW param with a fallback value and a warning log. Commit
03a72288c5 ("ath10k: wmi: add hw params entry for wcn3990") later
added WCN3990 HW entries, but it missed the n_cipher_suites.
Rather than seeing this warning every boot
ath10k_snoc 18800000.wifi: invalid hw_params.n_cipher_suites 0
let's provide the appropriate value.
Cc: Rakesh Pillai <pillair@qti.qualcomm.com>
Cc: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
They're provided as callbacks in ath10k_hif_ops and should be accessed
that way, if needed outside of snoc.c, and anyway, they're currently
unused outside snoc.c.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to regulator error handling, we should only start tearing down
the 'i - 1' clock when clock 'i' fails to enable. Otherwise, we might
end up with an unbalanced clock, where we never successfully enabled the
clock, but we try to disable it anyway.
Fixes: a6a793f987 ("ath10k: vote for hardware resources for WCN3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I rarely see drivers specify precise voltage requirements like this, but
if we really have to...let's at least give a little wiggle room. Board
designs (and accompanying device trees) may not provide exactly the
voltage listed here, and we shouldn't fail to probe just because of
this.
Round these ranges down to the nearest volt, and provide a 0.05V margin.
The regulator should provide its own supported ranges, which will
helpfully intersect with these ranges.
I would just as well remove these ranges entirely, but if I understand
correctly, there's some reason that QCOM SoC's like to set zero /
non-zero voltages.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a regulator fails to set its voltage, we end up with an unbalanced
call to regulator_disable(), because the error path starts with the
current regulator (which was never enabled).
Factor out the "on" function to perform (and unwind if failed) a single
regulator at a time, and then main loop (ath10k_snoc_vreg_on()) can just
worry about unwinding the regulators that were already enabled.
It also helps to factor out the "off" function, to avoid repeating some
code here.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_wcn3990_clk_info and ath10k_wcn3990_vreg_info are not
WCN3990-specific structures. They hold generic data. So don't name them
with wcn3990 specifics.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch from spin_lock to spin_lock_irqsave, because
wmi_ev_lock is used inside interrupt handler.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After being associated with some EDMA rx traffic, upon "down" driver
doesn't free all skbs in the rx ring.
Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx
buffers, unmap the physical memory and free the skb.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx buffers in EDMA mode are initialized to 4 bytes aligned size.
Remove the unnecessary alignment code applied on rx buffer size.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RGF_CAF_ICR register location has changed in Talyn-MB.
Add RGF_CAF_ICR_TALYN_MB to support the new address.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All wil6210 device memory access should be 4 bytes aligned. In io
blob wil6210 did not force alignment for read function, this caused
alignment fault on some platforms.
Fixing that by accessing all 4 lower bytes and return to host the
requested data.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize unset variable, and verify that mid is valid.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 used to notify cfg80211_del_sta on every fw disconnect event.
In disable_ap_sme mode the userspace manages the protocol SME and
FW sends disconnect event only due to link loss.
In disable_ap_sme mode, indicate CQM packet loss to let the host
control the connection and disconnect the link if needed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Separate sending command to the fw from the event handling function to
simplify the disconnect flow and track the from_event flag correctly.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A successful call to wil_tx_ring takes skb reference so
it will only be freed in wil_tx_complete. Consume the skb
in wil_find_tx_bcast_2 to prevent memory leak.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP configuration is stored by the driver. Upon FW error, disconnect
notification is sent to user space for any associated stations. AP is
then internally restarted with the stored configuration.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When enlarging rx_ring_order module param, wil6210 fails to load
because there are not enough Rx buffers.
Fix this by enlarging number of Rx buffers at startup, if needed based
on rx_ring_order.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Talyn-MB, the 11ad throughput is higher and performance drops
may occur in the current RX configuration due to unavailability
of Rx buffers.
Increase the RX descriptor ring, RX status ring and number of RX
buffers to stabilize the performance in high throughput.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With current reset flow, Talyn sometimes get stuck causing PCIe
enumeration to fail. Fix this by removing some reset flow operations
that are not relevant for Talyn.
Setting bit 15 in RGF_HP_CTRL is WBE specific and is not in use for
all wil6210 devices.
For Sparrow, BIT_HPAL_PERST_FROM_PAD and BIT_CAR_PERST_RST were set
as a WA an HW issue.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setting the same fake hash to all skbs prevents
distributing different flows to different CPU cores.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056534 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201383 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
new_flags is not used after setting its value. It is safe to remove
the unused variable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/wmi-tlv.c: In function 'ath10k_wmi_tlv_op_gen_config_pno_start':
drivers/net/wireless/ath/ath10k/wmi-tlv.c:3455:6: warning:
variable 'tlv_len' set but not used [-Wunused-but-set-variable]
It never used since inroduction in commit
ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to some spelling mistakes in ath10k_err and ath10k_dbg
messages:
"capablity" -> "capability"
"registed" -> "registered"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I had a couple concerns with this code. First, we definitely need to
set the error code if the kzalloc() fails. Secondly, I was worried that
if we didn't set "arsta->tx_stats" to NULL after freeing it, then it
looks to me like it might lead to a use after free. I can't test that,
but it's harmless to set it to NULL so I did.
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The host driver currently expects the channel info event to be
received in pairs for all the channels, i.e. the first
chan_info event for a particular channel will not have the
COMPLETE flag set and the second chan_info event for the
same channel will have the COMPLETE flag set.
The HL2.0 firmware sends only one channel info event per channel
which is scanned without the COMPLETE flag set. After sending the
chan_info_event for all the channels, the HL2.0 firmware sends a
chan_info_event with COMPLETE flag set to indicate the completion
of the channel info event.
The firmware does not indicate this behavior with any service bitmap
and hence a new firmware feature flag is used to handle the modified
parsing of the channel info events, in the host driver, for the
firmware which sends single channel info event per scanned channel.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value from devm_memremap() is not checked correctly.
The test is done against a wrong variable. This patch fix it.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ar->target_version is same for QCA99x0, QCA4019, QCA9888
and QCA9984, this ended up in assigning the wrong hw_mem_layouts.
This patch adds additional hw_rev check to assign correct
hw_mem_layouts.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
QCA9984 firmware 10.4-3.5.3-00057
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA4019.
Tested on:
QCA4019 firmware 10.4-3.2.1.1-00017
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WCN3990 firmware becomes unavailable,
the host driver receives a FW down indication, post
which all the direct hardware register access should
be avoided, in order to prevent improper behavior in
the host driver.
Set the crash_flush flag when the host driver receives
a FW_DOWN_IND via qmi, in order to stop the untimely
hardware register access. Also handle the case, where
we need to do core register only for the first FW_READY
indication, which is when we initialize the host driver.
All the subsequent FW_READY indication will be received
in subsystem recovery case and we only need to do the
restart work. The state of driver is maintained using
flags to distinguish between first and subsequent FW_READY
indication received.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.
Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug mask to control debug info of ath10k qmi
messaging layer.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
