With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath11k does MHI
register reading in this state. The issue was reported on Dell XPS 13
9310 but is seen also on XPS 15 and XPS 17 laptops.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041722.5271-1-bqiang@codeaurora.org
On some platforms it's not possible to allocate 32 MSI vectors for various
reasons, be it kernel configuration, VT-d disabled, buggy BIOS etc. So
ath11k was not able to use QCA6390 PCI devices on those platforms. Add
support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled. This
is because when interrupt migration happens, the msi_data may change.
However, msi_data is already programmed to rings during initial phase and
ath11k has no way to know that msi_data is changed during run time and
reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as QCA6390 doesn't set this flag too. Ath11k doesn't need to leave
IRQ enabled in suspend state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041714.5219-1-bqiang@codeaurora.org
This is to prepare for one MSI vector support. IRQ enable and disable
of CE and DP are done only in case of multiple MSI vectors.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041705.5167-1-bqiang@codeaurora.org
Like ATH11K_PCI_IRQ_CE0_OFFSET, define ATH11K_PCI_IRQ_DP_OFFSET for
DP to save the IRQ instead of base_vector from MSI config.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041655.5112-1-bqiang@codeaurora.org
This change adds two flags to indicate whether IRQ handler for CE
and DP can be called. This is because in one MSI vector case,
interrupt is not disabled in hif_stop and hif_irq_disable. Otherwise,
MHI interrupt is disabled too.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041646.5060-1-bqiang@codeaurora.org
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts
are initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq
is called, so ath11k reads msi_data again after request_irq is called,
and then the correct msi_data is programmed into QCA6390 hardware
components. Without this change, spurious interrupt occurs in case of
one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI
vectors, ath11k always get the same msi_data before and after request_irq,
that's why this change is only required when one MSI vector is to be
supported.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041636.5008-1-bqiang@codeaurora.org
Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':
Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
Hence, disable wakeup/release mhi using hw_param for other hardwares.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
Fixes: a05bd85133 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com
The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.
But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 01e34233c6 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org
DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.
Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org
Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.
The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.
BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com
Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.
This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.
ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com
Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.
Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
The DMA buffers of dbring which is used for spectral/cfr
starts at certain offset from original kmalloc() returned buffer.
This is not cache line aligned.
And also driver tries to access the data that is immediately before
this offset address (i.e. buff->paddr) after doing dma map.
This will cause cache line sharing issues and data corruption,
if CPU happen to write back cache after HW has dma'ed the data.
Fix this by mapping a cache line aligned buffer to dma.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com
Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.
This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.
The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)
Ath11k uses both these configurations to disable credit flow for the
WMI path completely.
Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:
country AU: DFS-ETSI
(2400 - 2483.5 @ 40), (36)
(5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
(5470 - 5600 @ 80), (27), DFS
(5650 - 5730 @ 80), (27), DFS
(5730 - 5850 @ 80), (36)
(57000 - 66000 @ 2160), (43), NO-OUTDOOR
If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:
* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")
There are several wrong assumption in the ath11k code:
* there is always a valid range below the weather radar
(actually: there could be no range below the weather radar range OR range
could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
(actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
(actually: the range could be smaller than 20 MHz)
These wrong assumption will lead in this example to a rule
(5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW
which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:
WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
[...]
Call trace:
[<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
[<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
[<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
[<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
[<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
[<ffffffc0000a9784>] worker_thread+0x25c/0x448
[<ffffffc0000aedc8>] kthread+0xd0/0xd8
[<ffffffc000085550>] ret_from_fork+0x10/0x40
ath11k c000000.wifi: failed to perform regd update : -22
Invalid regulatory domain detected
To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.
When these checks are in place, the processed rules for AU would end up as
country AU: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 36), (N/A)
(5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
(5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW
and will be accepted by the wireless regulatory code.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
There is a race condition whereby the tx completion handler can be invoked
before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we
could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because
it was not yet incremented). Ideally, this trace should be seen only if
mgmt tx has not happened but tx completion is received, and it is not
expected in this race condition.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com
Set proper values for max_regpower, max_power, max_antenna_gain as it
is because firmware will convert power values to 0.5dbm steps by
multiplying it with 2.
If txpower is not set, it will lead to cca stuck resulting in latency
issues for QCN9074.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com
In radio tap header, BAD FCS flag is not updated properly because
driver failed to update FCS_ERR flag in monitor mode.
In rx_desc, FCS_ERR information is available in rx_attention
structure and presence of this field indicates corresponding frame
failed FCS check.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com
When station connect to AP, the wmi command sequence is:
peer_create->vdev_start->vdev_up
and sequence of station disconnect fo AP is:
peer_delete->vdev_down->vdev_stop
The sequence of disconnect is not opposite of connect, it caused firmware
crash when it handle wmi vdev stop cmd when the AP is support TWT of
802.11 ax, because firmware need access the bss peer for vdev stop cmd.
[ 390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0
[ 390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g
[ 390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0
[ 390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0
[ 390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39
[ 399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39
[ 399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0
[ 399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0
[ 399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0
[ 399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0
[ 399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0
The opposite sequence of disconnect should be:
vdev_down->vdev_stop->peer_delete
This patch change the sequence of disconnect for station as above
opposite sequence for QCA6390, firmware not crash again with this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com
parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com
Currently in ath11k_mac_op_sta_statistics() there is the following
logic:
if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;
Unfortunately if this condition is true then the function returns without
setting parameters that follow the txrate. To address this issue remove the
return and instead invert the logic to set the txrate logic if
(arsta->txrate.legacy || arsta->txrate.nss).
The same was done also in ath10k in commit 1cd6ba8ae3 ("ath10k: remove return
for NL80211_STA_INFO_TX_BITRATE").
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org
When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW
is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also
need to be set, otherwise it is invalid because spec in IEEE Std
802.11™‐2020 as below.
Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield
VHT Extended NSS BW Capable, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS
BW Support subfield of the VHT Capabilities Information field.
dmesg have a message without this patch:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not
set it in ieee80211_register_hw(). So it is better to set it in ath11k.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org
Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
Currently while loop is used to find the tx completion ring number and
it is not required since the tx ring mask and the group id can be combined
to directly fetch the ring number. Hence remove the while loop
and directly get the ring number from tx mask and group id.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org
Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org
Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE
from cacheable memory so that descriptors could be prefetched during
tx completion handling.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org
In datapath, add branch predictors where required in the process rx().
This protects high value rx path without having performance overhead.
Also while processing rx packets, the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org
The usage of quota variable inside ath11k_dp_rx_process_received_packets()
is redundant. Since we would queue only max packets to the list before
calling this function so it would never exceed quota. Hence removing
usage of quota variable.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org
The Active Pdev and CAC check are done for each msdu in
ath11k_dp_rx_process_received_packets which is a overhead.
To avoid this overhead, collect all msdus in a per mac msdu
list and pass to function.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org
In ath11k_dp_process_rx(), after processing rx_desc from
ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free()
is accessed everytime because of done flag is not set.
To avoid this additional access to ath11k_hal_srng_dst_num_free(),
increment total_msdu_reaped only when continuation is not set and
update done flag correspondingly.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org
In data path, to reduce the CPU cycles spending on descriptor access
wrapper function, changed those functions as static inline.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org
tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.
Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org
Host driver doesn't need to process CE8 interrupts (used
by target independently)
The volume of interrupts is huge within short interval,
CPU0 CPU1 CPU2 CPU3
14022188 0 0 0 GIC 71 Edge ce8
Hence disabling unused CE8 interrupt will improve CPU usage.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org
Currently the updated bandwidth for the peer will be configured
to the firmware after channel switch from the sta_rc_update_wk.
If the updated bandwidth is greater than the configured peer phymode
during the peer assoc may result firmware assert.
For example, initially AP is in HE40 mode and the peer phymode is
configured as MODE_11AX_HE40 during peer assoc. Now user change the
channel width to HE80 then, the peer bandwidth will be updated as
HE80 to the firmware.
This will trigger firmware assert due to peer bandwidth is greater than
the peer phymode.
Fix this issue by sending peer assoc command before setting the updated
peer bandwith to firmware.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com
Below compilation error is reported when built with W=1,
drivers/net/wireless/ath/ath11k/mac.c:5408:22: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter]
changed_flags is set, but left unused. So, remove unnecessary set.
Compile tested only.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636609967-5114-1-git-send-email-quic_seevalam@quicinc.com
In CE pipe cleanup, DMA memory gets freed by the aligned address
(base_addr_owner_space) which is wrong. It needs to be freed
by the address (base_addr_owner_space_unaligned) returned by
dma_alloc. So free the dma memory by the proper address.
This was found in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636561290-18966-1-git-send-email-quic_periyasa@quicinc.com
In STA kickout event processing, the peer object is protected
under spin lock BH. Release this lock after picking up the vdev_id
from the peer object instead after ieee80211_report_low_ack().
This will minimize the lock hold period which will improve
performance since base_lock is used across the data path.
This was found in code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636560388-24955-1-git-send-email-quic_periyasa@quicinc.com
When there is an error in add interface process from
ath11k_mac_set_kickout(), the code attempts to handle a
fallback for add_interface. When this fallback succeeds, the
driver returns zero rather than error code. This leads to
success for the non created VAP. In cleanup, driver gets
remove interface callback for the non created VAP and
proceeds to self peer delete request which leads to FW assert.
Since it was already deleted on the fallback of add interface,
return the actual error code instead of fallback return code.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636558557-2874-1-git-send-email-quic_periyasa@quicinc.com
Firmware expects host to authorize the peer after the successful key
install. But host authorize the peer before the key install, this trigger
the firmware assert which leads to Q6 crash. To avoid this Q6 crash, host
should authorize the peer after the key install. So introduce is_authorized
in peer object to identify that peer is authorize or not. When
IEEE80211_STA_CONTROL_PORT flag is unset, peer move to authorize state
before the vdev up. When the same flag is set then peer move to authorize
state after vdev up. So added authorise check in ath11k_bss_assoc() to
handle the earlier state transition case. Also added the WMI authorize
procedure in ath11k_mac_op_sta_state() to handle the non-earlier state
transition case.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636554200-12345-1-git-send-email-quic_periyasa@quicinc.com
AUTH flag is needed when peer assoc command is sent from host in
security mode for non-assoc cases. Firmware will handle AUTH flag
when client is associating as AUTH flag will be set after key exchange.
For internally provided peer assoc commands from host, there won't be
any key exchange, so AUTH flag is expected to be set in host.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635177786-20854-1-git-send-email-quic_ramess@quicinc.com
HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message
was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from
bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in
the request message.
In commit 701e48a43e ("ath11k: add packet log support for QCA6390"), both
HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask
calculation is not valid for platforms which has multiple pdevs with 1 rxdma
per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it
to consider pdev_idx as well, to make it compatible for both single and multi
pd cases.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1
Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org
To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.
Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.
To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org
It's more descriptive to use the actual enum used by the firmware instead of a
boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org
Commit 6f4d70308e ("ath11k: support SMPS configuration for 6 GHz") changed
"if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap &
WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means
NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz.
However, WCN6855 supports 6 GHz but it does not support feature
NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for
WCN6855.
Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not
support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's
the only other device supporting 6 GHz band.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-3-jouni@codeaurora.org
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org
ath.git patches for v5.16. Major changes:
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011054919.77071-1-bqiang@codeaurora.org
Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.
This is a theoretical fix found during code review, no visible impact.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org
When doing "rmmod ath11k_pci", ath11k performs global SOC reset
and MHI reset, where 0 address access is captured by IOMMU. See
log below:
...
[ 133.953860] ath11k_pci 0000:02:00.0: setting mhi state: DEINIT(1)
[ 133.959714] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
[ 133.973854] ath11k_pci 0000:02:00.0: MHISTATUS 0xff04
[ 133.974095] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020]
...
This issue is also observed in SSR process, cause a similar
sequence as above is performed.
Such an invalid access occurs because, during rmmod or SSR, MSI
address is cleared but HW MSI functionality not disabled, thus HW
target is able to raise an MSI transaction with 0 as MSI address.
So it can be fixed by simply disabling MSI before reset. For SSR,
since MSI functionality is still needed after target is brought
back, we need to reenable it.
Also change naming of some interfaces related.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-5-jouni@codeaurora.org
Variable fw_size is being assigned a value that is never read and
being re-assigned a new value in the next statement. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Fixes: 336e7b53c8 ("ath11k: clean up BDF download functions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211006105529.1011239-1-colin.king@canonical.com
Stephen reported that ath11k was failing to build on m68k and xtensa:
In file included from <command-line>:0:0:
In function 'ath11k_peer_assoc_h_smps',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:2362:2:
include/linux/compiler_types.h:317:38: error: call to '__compiletime_assert_650' declared with attribute error: FIELD_GET: type of reg too small for mask
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/compiler_types.h:298:4: note: in definition of macro '__compiletime_assert'
prefix ## suffix(); \
^
include/linux/compiler_types.h:317:2: note: in expansion of macro '_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^
include/linux/bitfield.h:52:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG((_mask) > (typeof(_reg))~0ull, \
^
include/linux/bitfield.h:108:3: note: in expansion of macro '__BF_FIELD_CHECK'
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/net/wireless/ath/ath11k/mac.c:2079:10: note: in expansion of macro 'FIELD_GET'
smps = FIELD_GET(IEEE80211_HE_6GHZ_CAP_SM_PS,
Fix the issue by using le16_get_bits() to specify the size explicitly.
Fixes: 6f4d70308e ("ath11k: support SMPS configuration for 6 GHz")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity complains that a constant variable guards dead code. In fact,
mpdu_buf is set NULL and never updated.
4834err_merge_fail:
null: At condition mpdu_buf, the value of mpdu_buf must be NULL.
dead_error_condition: The condition mpdu_buf cannot be true.
CID 92162 (#1 of 1): 'Constant' variable guards dead code (DEADCODE)
dead_error_line: Execution cannot reach the expression decap_format !=
DP_RX_DECAP_TYPE_RAW inside this statement: if (mpdu_buf && decap_forma....
Local variable mpdu_buf is assigned only once, to a constant value, making it
effectively constant throughout its scope. If this is not the intent, examine
the logic to see if there is a missing assignment that would make mpdu_buf not
remain constant.
4835 if (mpdu_buf && decap_format != DP_RX_DECAP_TYPE_RAW) {
Fix this by removing mpdu_buf and unreachable code.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927150743.19816-1-tim.gardner@canonical.com
For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.
Note that this issue is only found on Intel platform.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Parse SMPS configuration from IEs and configure. Without this,
SMPS is not enabled for 6 GHz band.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913175510.193005-3-jouni@codeaurora.org
Currently A-MPDU aggregation parameters are not being configured
during peer association for 6 GHz band. Hence, extract these
parameters from station's capabilities received in association
request and send to firmware. Without this, A-MPDU aggregation
is not happening in 6 GHz band.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913175510.193005-2-jouni@codeaurora.org
Scan failure can not be recovered from when running a loop of the
following steps:
1. run scan: "iw wlan scan".
2. run command: echo assert > /sys/kernel/debug/ath11k/qca6490\ hw2.0/simulate_fw_crash
immediately after step 1.
result:
scan failed and can not recover even when wlan recovery succeeds:
command failed: Device or resource busy (-16)
reason:
When scan arrives, WMI_START_SCAN_CMDID is sent to the firmware and
function ath11k_mac_op_hw_scan() returns, then simulate_fw_crash arrives
and the scan started event does not arrive, and then it starts to do
recovery of wlan. __ath11k_mac_scan_finish() which is called from
ath11k_core_halt() is one step of recovery, it will not call
ieee80211_scan_completed() by logic currently because the scan state is
ATH11K_SCAN_STARTING. Thus it leads the scan not being completed in
mac80211, and leads all consecutive scans failing with -EBUSY in
nl80211_trigger_scan even after wlan recovery success.
Indicate scan complete with aborted flag to mac80211 for
ATH11K_SCAN_STARTING to allow recovery from scan failed with "Device or
resource busy (-16)" after wlan recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-3-jouni@codeaurora.org
ath11k prints "Received scan event for unknown vdev" when doing the
following test:
1. trigger scan
2. wait 0.2 second
3. iw reg set or 11d scan complete from firmware
Reason: When iw reg set or 11d scan complete, the new country code will
be set to the firmware, and the new regdomain info indicated to ath11k,
then the new channel list will be sent to the firmware. The firmware
will cancel the current scan after receiving WMI_SCAN_CHAN_LIST_CMDID
which is used for the new channel list, and the state of ath11k is
ATH11K_SCAN_RUNNING, then ath11k_get_ar_on_scan_abort() returns NULL and
ath11k_scan_event() returns at this point and does not indicate scan
completion to mac80211.
Indicate scan completion to mac80211 and get rid of the "Received scan
event for unknown vdev" print for the above case.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-2-jouni@codeaurora.org
When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.
[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Add HTT stats support for,
29-ATH11K_DBG_HTT_EXT_STATS_PEER_CTRL_PATH_TXRX_STATS:
Used to dump the control path txrx stats for each connected peer.
Usage:
echo 29 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/netdev\:wlan0/stations/
<sta mac>/htt_peer_stats.
31-ATH11K_DBG_HTT_EXT_STATS_PDEV_TX_RATE_TXBF_STATS:
Used to dump the per pdev tx rate txbf stats.
Usage:
echo 31 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
32-ATH11k_DBG_HTT_EXT_STATS_TXBF_OFDMA:
Used to dump the TXBF ofdma stats for all ofdma users.
Usage:
echo 32 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
37-ATH11K_DBG_HTT_EXT_PHY_COUNTERS_AND_PHY_STATS:
Used to dump the mac and phy txrx counts and phy stats like per chain rssi
and ANI level.
Usage:
echo 37 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type
cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00486-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-6-jouni@codeaurora.org
In debugfs_htt_stats.c, masking and shifting is done to get
stats values. Instead use GENMASK and FIELD_GET to improve
code readability and maintenance.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-5-jouni@codeaurora.org
To support the HTT Stats DebugFS interface a single large buffer that
contains the stats must be provided to the DebugFS infrastructure.
In the current code, for each class of stats, the stats are first
formatted in a local on-stack buffer, and then the local buffer is
copied to the large DebugFS buffer.
This logic has a problem when, for a given class, the formatted
stats exceed the size of the on-stack buffer. When this occurs the
stats for this class is truncated. In addition, this logic is
inefficient since it introduces an unnecessary memory copy.
To address these issues, update the logic to no longer use a local
on-stack buffer, and instead write the formatted data directly into
the large DebugFS buffer.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-4-jouni@codeaurora.org
Get rid of macro HTT_DBG_OUT and replace it with scnprintf().
The macro does not do anything else. Added required new line
characters to scnprintf() for proper display.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-3-jouni@codeaurora.org
Renaming of macro is done to describe the macro functionality
better as the macro functionality is modified in next patch-sets.
No functional changes are done.
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913223148.208026-2-jouni@codeaurora.org
The buffer pointed to by event is not freed in case
ATH11K_FLAG_UNREGISTERING bit is set, resulting in
memory leak, so fix it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-4-jouni@codeaurora.org
Current code clears debug registers after SOC global reset performed
in ath11k_pci_sw_reset. However at that time those registers are
not accessible due to reset, thus they are actually not cleared at all.
For WCN6855, it may cause target fail to initialize. This issue can be
fixed by moving clear action ahead.
In addition, on some specific platforms, need to add delay to wait
those registers to become accessible.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-3-jouni@codeaurora.org
There are MSDUs whose length are invalid. For example,
attackers may inject on purpose truncated A-MSDUs with
invalid MSDU length.
Such MSDUs are marked with an err bit set in rx attention
tlvs, so we can check and drop them.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210913180246.193388-2-jouni@codeaurora.org
WCN6855 has 2 phys, one is 2G, another is 5G/6G, so it should copy the
cap info of 6G band under the check of WMI_HOST_WLAN_5G_CAP as well as
for the 5G band. Some chips like QCN9074 only have 6G, not have 2G and
5G, and this 6G capability is also under WMI_HOST_WLAN_5G_CAP, so this
change will not disturb it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-4-jouni@codeaurora.org
For some chips such as WCN6855, single_pdev_only is set in struct
ath11k_hw_params which means ath11k calls ieee80211_register_hw() only
once and create only one device interface, and that device interface
supports all 2G/5G/6G channels.
ath11k_mac_setup_channels_rates() sets up the channels and it is called
for each device interface. It is called only once for single_pdev_only,
and then set up all channels for 2G/5G/6G. The logic of
ath11k_mac_setup_channels_rates() is not suitable for single_pdev_only,
it leads to all 6G channels being disabled for the device interface
which is single_pdev_only such as WCN6855.
Add channel frequency checks for the 6G band and enable the 6G channels
properly based on what is supported by the chip.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-3-jouni@codeaurora.org
WCN6855 uses single_pdev_only, so it supports both the 5G and 6G bands
in the same ath11k/pdev and it needs to enable ht_cap/vht_cap for the 5G
band, otherwise it will downgrade to non-HT mode for the 5G band. Some
chips like QCN9074 only support the 6G band, not the 5G band, and use
the flag ar->supports_6ghz which is true to discard ht_cap/vht_cap.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210804181217.88751-2-jouni@codeaurora.org
When ath11k receives survey request, choose the 6 GHz band when enabled.
Without this, survey request does not include any 6 GHz band results,
thereby causing auto channel selection to fail.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-3-jouni@codeaurora.org
Frequency in rx status is being filled incorrectly in the 6 GHz band as
channel number received is invalid in this case which is causing packet
drops. So fix that.
Fixes: 5dcf42f8b7 ("ath11k: Use freq instead of channel number in rx path")
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-2-jouni@codeaurora.org
Add support for the 6 GHz channel 2 with center frequency 5935 MHz and
operating class 136 per IEEE Std 802.11ax-2021, Table E-4.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210722102054.43419-1-jouni@codeaurora.org
When the driver sends a peer create cmd, the firmware responds with
WMI_PEER_CREATE_CONF_EVENTID to confirm the firmware received
WMI_PEER_CREATE_CMDID. Since the peer create conf event is not handled
in ath11k_wmi_tlv_op_rx, we are getting unknown event id warning prints
during peer creation.
Add WMI_PEER_CREATE_CONF_EVENTID in wmi_tlv_event_id and handle
the same as unsupported event id under wmi logs.
warning prints:
[ 4382.230817] ath11k_pci 0000:01:00.0: Unknown eventid: 0x601a
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-9-jouni@codeaurora.org
Facing below warning prints when we do wifi down in multiple VAPs scenario.
warning print:
ath11k c000000.wifi: No VIF found for vdev 2
...
ath11k c000000.wifi: No VIF found for vdev 0
In ath11k_mac_get_arvif_by_vdev_id(), we iterate all the radio to get the
arvif for the requested vdev_id through ath11k_mac_get_arvif().
ath11k_mac_get_arvif() throws a warning message if the given vdev_id is
not found in the given radio. So to avoid the warning message, add
the allocated_vdev_map cross check against the given vdev_id before using
ath11k_mac_get_arvif() to ensure that vdev_id is allocated in the
given radio.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-8-jouni@codeaurora.org
In scenario when a peer is disassociating, there could be
multiple places where a reo cmd ring is accessed, such as
during aggregation teardown, tid queue cleanup, etc.
When this happens during firmware recovery where accessing of FW/HW
resources/registers is not recommended, accessing reo cmd ring in
this case could lead to crash or undefined behaviour.
Hence avoid this by checking for corresponding flag to avoid
accessing reo cmd ring during firmware recovery.
Sample crash:
[ 3936.456050] Unhandled fault: imprecise external abort (0x1c06) at 0x54bb842a
[ 3936.456411] WARN: Access Violation!!!, Run "cat /sys/kernel/debug/qcom_debug_logs/tz_log" for more details
[ 3936.467997] pgd = b4474000
[ 3936.477440] [54bb842a] *pgd=6fa61831, *pte=7f95d59f, *ppte=7f95de7e
<snip>
[ 3937.177436] [<8030ab10>] (_raw_spin_unlock_bh) from [<7f5e9eb8>] (ath11k_hal_reo_cmd_send+0x440/0x458 [ath11k])
[ 3937.185730] [<7f5e9eb8>] (ath11k_hal_reo_cmd_send [ath11k]) from [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd+0x2c/0xcc [ath11k])
[ 3937.195524] [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd [ath11k]) from [<7f602f10>] (ath11k_peer_rx_tid_reo_update+0x84/0xbc [ath11k])
[ 3937.206984] [<7f602f10>] (ath11k_peer_rx_tid_reo_update [ath11k]) from [<7f605a9c>] (ath11k_dp_rx_ampdu_stop+0xa8/0x130 [ath11k])
[ 3937.218532] [<7f605a9c>] (ath11k_dp_rx_ampdu_stop [ath11k]) from [<7f5f6730>] (ath11k_mac_op_ampdu_action+0x6c/0x98 [ath11k])
[ 3937.230250] [<7f5f6730>] (ath11k_mac_op_ampdu_action [ath11k]) from [<c7b6e890>] (___ieee80211_stop_rx_ba_session+0x98/0x144 [mac80211])
[ 3937.241499] [<c7b6e890>] (___ieee80211_stop_rx_ba_session [mac80211]) from [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions+0x4c/0xf4 [)
[ 3937.253833] [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions [mac80211]) from [<c7b63460>] (ieee80211_sta_eosp+0x5b8/0x960 [mac80211])
[ 3937.266764] [<c7b63460>] (ieee80211_sta_eosp [mac80211]) from [<c7b66da8>] (__sta_info_flush+0x9c/0x134 [mac80211])
[ 3937.278826] [<c7b66da8>] (__sta_info_flush [mac80211]) from [<c7b7bd00>] (ieee80211_stop_ap+0x14c/0x28c [mac80211])
[ 3937.289240] [<c7b7bd00>] (ieee80211_stop_ap [mac80211]) from [<7f509cf0>] (__cfg80211_stop_ap+0x4c/0xd8 [cfg80211])
[ 3937.299629] [<7f509cf0>] (__cfg80211_stop_ap [cfg80211]) from [<7f4dddec>] (cfg80211_leave+0x24/0x30 [cfg80211])
[ 3937.310041] [<7f4dddec>] (cfg80211_leave [cfg80211]) from [<7f4de03c>] (cfg80211_netdev_notifier_call+0x174/0x48c [cfg80211])
[ 3937.320457] [<7f4de03c>] (cfg80211_netdev_notifier_call [cfg80211]) from [<80339928>] (notifier_call_chain+0x40/0x68)
[ 3937.331636] [<80339928>] (notifier_call_chain) from [<803399a8>] (raw_notifier_call_chain+0x14/0x1c)
[ 3937.342221] [<803399a8>] (raw_notifier_call_chain) from [<8073bb00>] (call_netdevice_notifiers+0xc/0x14)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01240-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-7-jouni@codeaurora.org
Firmware crash is seen randomly, because of sending wrong vdev_id
in vdev_create command. This is due to free_vdev_map value being 0.
free_vdev_map is getting assigned after ieee80211_register_hw. In
some race conditions, add_interface api is getting called before
assigning value to free_vdev_map. Fix this by assigning free_vdev_map
before ieee80211_register_hw.
Also, moved ar->cc_freq_hz and ar->txmgmt_idr initialization before
ieee80211_register_hw to avoid such race conditions.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00948-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-6-jouni@codeaurora.org
Firmware blocks all data traffic until the key is plumbed. But, with
software encryption mode, key is never plumbed to firmware. Due to this,
a traffic failure in software encryption mode has been observed. Hence,
firmware has introduced a flag to differentiate software encryption
mode. This flag can be passed during vdev_start command.
Enable WMI_VDEV_START_HW_ENCRYPTION_DISABLED flag in vdev_start command
to notify firmware to disable hardware encryption for a vdev. This is set
if raw mode software encryption is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01421-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-5-jouni@codeaurora.org
Whenever ath11k is bootup with a user country already set, cfg80211
notifies this country info to ath11k soon after registration, where the
notification is sent to the firmware for fetching the rules of this user
country input.
Multiple race conditions could be seen in this scenario where a new
request is either lost as pointed in [1] or a new regd overwrites the
default regd provided by the firmware during bootup. Note that, the
default regd is used for intersection purpose and hence it should not be
overwritten.
The main reason as pointed by [1] is the usage of ATH11K_FLAG_REGISTERED
flag which is updated after completion of core registration, whereas the
reg notification from cfg80211 and wmi events for the corresponding
request can happen much before that. Since the ATH11K_FLAG_REGISTERED is
currently used to determine if the event containing reg rules belong to
default regd or for user request, there is a possibility of the default
regd getting overwritten.
Since the default reg rules will be received only once per pdev on
firmware load, the above flag based check can be replaced with a check
to see if default_regd is already set, so that we can now always update
the new_regd. Also if the new_regd is set, this will be always used to
update the reg rules for the registered phy.
[1] https://patchwork.kernel.org/project/linux-wireless/patch/1829665.1PRlr7bOQj@ripper/
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-4-jouni@codeaurora.org
During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.
See below snap for example,
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered
root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC
In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.
This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Update the fields of pdev tx and tx firmware stats structure.
Missing fields resulted in wrong fw stats to be displayed as below.
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/
ipq8074\ hw2.0/mac0/fw_stats/pdev_stats | grep Illegal
Illegal rate phy errors 36839112
Note that this struct was missing its members from initial driver
support and this change doesn't introduce/modify the structure for
firmware changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-2-jouni@codeaurora.org
Fix sending rx_buf_sz to ath11k_dp_tx_htt_rx_filter_setup()
to enable pktlog full or lite mode. Depending on mode update the
trace buffer with log type full/lite.
Pktlog lite is a lighter version of pktlog. This can be used to capture
PPDU stats. These are useful for firmware performance debugging.
pktlog lite dumps are enabled using,
echo "0x0 1" > ath11k/IPQ8074 hw2.0/mac0/pktlog_filter
Tested On: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01233-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-1-jouni@codeaurora.org
Add support for rx decapsulation offload by advertising
the support to mac80211 during registration. Also ensure
the frames have the RX_FLAG_8023 flag set in decap offload
frames before passing to mac80211.
Since the packets delivered to the driver are in 802.3 format, these
can be sent to the network core with minimal processing in mac80211.
This helps in releasing some CPU cycles in the host processor and
thereby improving the performance.
Two exceptions are made before passing decap frames, one is
for EAPOL packets since mac80211 8023 fast rx for the sta
is set only after authorization, other case is for multicast
packets to validate PN in mac80211. In both the cases the
decap frames are converted to 80211 frame and sent to mac80211.
Ethernet decap can be enabled by using frame_mode modparam:
insmod ath11k frame_mode=2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00844-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721204217.120572-1-jouni@codeaurora.org
The ath11k_dbring_bufs_replenish() and ath11k_dbring_fill_bufs()
take a "gfp" parameter but they since they take spinlocks, the
allocations they do have to be atomic. This causes a bug because
ath11k_dbring_buf_setup passes GFP_KERNEL for the gfp flags.
The fix is to use GFP_ATOMIC and remove the unused parameters.
Fixes: bd6478559e ("ath11k: Add direct buffer ring support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210812070434.GE31863@kili
qmi tries to allocate a large contiguous dma memory at first,
on the AMD Ryzen platform it fails, then retries with small slices.
So set flag GFP_NOWARN to avoid flooding dmesg.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823063258.37747-1-aaron.ma@canonical.com
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code a bit according to the use of a flexible-array member in
struct scan_chan_list_params instead of a one-element array, and use the
struct_size() helper.
Also, save 25 (too many) bytes that were being allocated:
$ pahole -C channel_param drivers/net/wireless/ath/ath11k/reg.o
struct channel_param {
u8 chan_id; /* 0 1 */
u8 pwr; /* 1 1 */
u32 mhz; /* 2 4 */
/* Bitfield combined with next fields */
u32 half_rate:1; /* 4:16 4 */
u32 quarter_rate:1; /* 4:17 4 */
u32 dfs_set:1; /* 4:18 4 */
u32 dfs_set_cfreq2:1; /* 4:19 4 */
u32 is_chan_passive:1; /* 4:20 4 */
u32 allow_ht:1; /* 4:21 4 */
u32 allow_vht:1; /* 4:22 4 */
u32 allow_he:1; /* 4:23 4 */
u32 set_agile:1; /* 4:24 4 */
u32 psc_channel:1; /* 4:25 4 */
/* XXX 6 bits hole, try to pack */
u32 phy_mode; /* 8 4 */
u32 cfreq1; /* 12 4 */
u32 cfreq2; /* 16 4 */
char maxpower; /* 20 1 */
char minpower; /* 21 1 */
char maxregpower; /* 22 1 */
u8 antennamax; /* 23 1 */
u8 reg_class_id; /* 24 1 */
/* size: 25, cachelines: 1, members: 21 */
/* sum members: 23 */
/* sum bitfield members: 10 bits, bit holes: 1, sum bit holes: 6 bits */
/* last cacheline: 25 bytes */
} __attribute__((__packed__));
as previously, sizeof(struct scan_chan_list_params) was 32 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[1]; /* 6 25 */
/* size: 32, cachelines: 1, members: 3 */
/* padding: 1 */
/* last cacheline: 32 bytes */
};
and now with the flexible array transformation it is just 8 bytes:
$ pahole -C scan_chan_list_params drivers/net/wireless/ath/ath11k/reg.o
struct scan_chan_list_params {
u32 pdev_id; /* 0 4 */
u16 nallchans; /* 4 2 */
struct channel_param ch_param[]; /* 6 0 */
/* size: 8, cachelines: 1, members: 3 */
/* padding: 2 */
/* last cacheline: 8 bytes */
};
This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210823172159.GA25800@embeddedor
Firmware updates EEPROM support capability in QMI FW caps, send QMI BDF
download request message with file type EEPROM, to get caldata download
from EEPROM. Firmware takes more time to update cal data from EEPROM, so
increase QMI timeout.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-5-jouni@codeaurora.org
In current code, AHB/PCI uses two separate functions to download
BDF file. Refactor code and make a common function to send QMI BDF
download request for both AHB and PCI devices. This patch has no
functional change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-3-jouni@codeaurora.org
Reuse board_size from hw_params, add cal_offset to hw params.
This patch is clean up only, there is no change in functionality.
cal_size was unused, so remove that.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org
gcc-11 with the kernel address sanitizer prints a warning for this
driver:
In function 'ath11k_peer_assoc_h_vht',
inlined from 'ath11k_peer_assoc_prepare' at drivers/net/wireless/ath/ath11k/mac.c:1632:2:
drivers/net/wireless/ath/ath11k/mac.c:1164:13: error: 'ath11k_peer_assoc_h_vht_masked' reading 16 bytes from a region of size 4 [-Werror=stringop-overread]
1164 | if (ath11k_peer_assoc_h_vht_masked(vht_mcs_mask))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/mac.c: In function 'ath11k_peer_assoc_prepare':
drivers/net/wireless/ath/ath11k/mac.c:1164:13: note: referencing argument 1 of type 'const u16 *' {aka 'const short unsigned int *'}
drivers/net/wireless/ath/ath11k/mac.c:969:1: note: in a call to function 'ath11k_peer_assoc_h_vht_masked'
969 | ath11k_peer_assoc_h_vht_masked(const u16 vht_mcs_mask[NL80211_VHT_NSS_MAX])
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
According to analysis from gcc developers, this is a glitch in the
way gcc tracks the size of struct members. This should really get
fixed in gcc, but it's also easy to work around this instance
by changing the function prototype to no include the length of
the array.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99673
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210322160253.4032422-5-arnd@kernel.org
Populate the below hw parameters as per the QCN9074 support
1. FFT bin size as two bytes
2. Maximum FFT bin count as 1024
3. Summary report pad size as 16
4. FFT report header length as 24
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-5-jouni@codeaurora.org
User was not able to configure the spectral with the FFT bin count 32.
In all supported platforms, the expected minimum FFT bin count is 32 but
it was wrongly defined as 64. This restrict the user to not configure
down to the actually supported minimum FFT bin count. So update the
minimum FFT bin count as 32.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-4-jouni@codeaurora.org
Below parameters have been identified as configurable across the platforms.
So to scale the spectral across the platforms, move these parameter
into hw param.
1. Maximum FFT bins
2. Summary report pad size
3. FFT report header length
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-3-jouni@codeaurora.org
In IPQ8074, actual FFT bin size is two bytes but hardware reports it
with extra pad size of two bytes for each FFT bin. So finally each FFT
bin advertise as four bytes size in the collected data. This FFT pad is
not advertised in IPQ6018 platform. To accommodate this different
behavior across the platforms, introduce the hw param fft_pad_sz and use
it in spectral process. Also group all the spectral params under the new
structure in hw param structure for scalable in future.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721180809.90960-2-jouni@codeaurora.org
