The RTL8156 support CDC NCM mode. And users could set the configuration
of the USB device between vendor and NCM mode dynamically by themselves.
That is, the driver doesn't need to set vendor mode from NCM mode.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the timeout occurs, we still have to run the following process
for releasing patch request. Otherwise, the PHY would keep no link.
Therefore, use break to stop the loop of loading firmware and
release the patch request rather than return the function directly.
Fixes: 4a51b0e8a0 ("r8152: support PHY firmware for RTL8156 series")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new firmware type and method for RTL8156 series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.
Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bits operations to record and check the firmware.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.
For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until very recently, the usbnet framework only had support functions
for devices which reported the link speed by explicitly querying the
PHY over a MDIO interface. However, the cdc_ether devices send
notifications when the link state or link speeds change and do not
expose the PHY (or modem) directly.
Support funtions (e.g. usbnet_get_link_ksettings_internal()) to directly
query state recorded by the cdc_ether driver were added in a previous patch.
Instead of cdc_ether spewing the link speed into the dmesg buffer,
record the link speed encoded in these notifications and tell the
usbnet framework to use the new functions to get link speed/state.
User space can now get the most recent link speed/state using ethtool.
v4: added to series since cdc_ether uses same notifications
as cdc_ncm driver.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until very recently, the usbnet framework only had support functions
for devices which reported the link speed by explicitly querying the
PHY over a MDIO interface. However, the cdc_ncm devices send
notifications when the link state or link speeds change and do not
expose the PHY (or modem) directly.
Support funtions (e.g. usbnet_get_link_ksettings_internal()) to directly
query state recorded by the cdc_ncm driver were added in a previous patch.
So instead of cdc_ncm spewing the link speed into the dmesg buffer,
record the link speed encoded in these notifications and tell the
usbnet framework to use the new functions to get link speed/state.
Link speed/state is now available via ethtool.
This is especially useful given all current RTL8156 devices emit
a connection/speed status notification every 32ms and this would
fill the dmesg buffer. This implementation replaces the one
recently submitted in de658a195e :
"net: usb: cdc_ncm: don't spew notifications"
v2: rebased on upstream
v3: changed variable names
v4: rewrote commit message
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old method for reporting link speed assumed a driver uses the
generic phy (mii) MDIO read/write functions. CDC devices don't
expose the phy.
Add a primitive internal version reporting back directly what
the CDC notification/status operations recorded.
v2: rebased on upstream
v3: changed names and made clear which units are used
v4: moved hunks to correct patch; rewrote commmit messages
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic functions assumed devices provided an MDIO interface (accessed
via older mii code, not phylib). This is true only for genuine ethernet.
Devices with a higher level of abstraction or based on different
technologies do not have MDIO. To support this case, first rename
the existing functions with _mii suffix.
v2: rebased on changed upstream
v3: changed names to clearly say that this does NOT use phylib
v4: moved hunks to correct patch; reworded commmit messages
Signed-off-by : Oliver Neukum <oneukum@suse.com>
Tested-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923
Fixes: ec5791c202 ("r8152: separate the rx buffer size")
Reported-by: Robert Davies <robdavies1977@gmail.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e ("USB host CDC Phonet network interface driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver data for the data interface has already been set by
usb_driver_claim_interface() so drop the subsequent redundant
assignment.
Note that this also avoids setting the driver data three times in case
of a combined interface.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors in protocol should be logged when the driver aborts operations.
If the driver can carry on and "humor" the device, then emitting
the message as debug output level is fine.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several error paths in bind/probe code will only emit
output using dev_dbg. But if we are going to fail the
bind/probe, emit related output with "err" priority.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason for preventing the creation and removal
of qmimux network interfaces when the underlying interface
is up.
This makes qmi_wwan mux implementation more similar to the
rmnet one, simplifying userspace management of the same
logical interfaces.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 134f98bcf1.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some messages are before calling register_netdev(), so replace
netif_err() with dev_err().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return error code if autosuspend_en, eee_get, or eee_set don't exist.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
U1/U2 shoued be enabled for USB 3.0 or later. The USB 2.0 doesn't
support it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.
Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass through mode is to allow packets in MAP format to be passed
on to the stack. rmnet driver can be used to process and demultiplex
these packets.
Pass through mode can be enabled when the device is in raw ip mode only.
Conversely, raw ip mode cannot be disabled when pass through mode is
enabled.
Userspace can use pass through mode in conjunction with rmnet driver
through the following steps-
1. Enable raw ip mode on qmi_wwan device
2. Enable pass through mode on qmi_wwan device
3. Create a rmnet device with qmi_wwan device as real device using netlink
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/1611560015-20034-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add qmimux interface sysfs file qmap/mux_id to show qmap id set
during the interface creation, in order to provide a method for
userspace to associate QMI control channels to network interfaces.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize tasklet using tasklet_init() rather than open-coding it.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In general, device drivers should not be enabled by default.
Fixes: 657bc1d10b ("r8153_ecm: avoid to be prior to r8152 driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210113144309.1384615-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit enables the use of the r8153_ecm driver, introduced with
commit c1aedf015e ("net/usb/r8153_ecm: support ECM mode for
RTL8153") for the Lenovo Powered USB-C Hub (17ef:721e) based on the
Realtek RTL8153B chip.
This results in the following driver preference:
- if r8152 is available, use the r8152 driver
- if r8152 is not available, use the r8153_ecm driver
This is done to prevent the NIC from constantly sending pause frames
when the host system enters standby (fixed by using the r8152 driver
in "r8152: Add Lenovo Powered USB-C Travel Hub"), while still allowing
the device to work with the r8153_ecm driver as a fallback.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-3-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Signed-off-by: Leon Schuermann <leon@is.currently.online>
Tested-by: Leon Schuermann <leon@is.currently.online>
Link: https://lore.kernel.org/r/20210111190312.12589-2-leon@is.currently.online
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Fixes: 039ee17d1b ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Link: https://lore.kernel.org/r/20210108095839.3335-1-andrey.zhizhikin@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When measuring the throughput (iperf3 + TCP) while routing on a
not-so-powerful device (Mediatek MT7621, 880MHz CPU), I noticed that I
achieved significantly lower speeds with QMI-based modems than for
example a USB LAN dongle. The CPU was saturated in all of my tests.
With the dongle I got ~300 Mbit/s, while I only measured ~200 Mbit/s
with the modems. All offloads, etc. were switched off for the dongle,
and I configured the modems to use QMAP (16k aggregation). The tests
with the dongle were performed in my local (gigabit) network, while the
LTE network the modems were connected to delivers 700-800 Mbit/s.
Profiling the kernel revealed the cause of the performance difference.
In qmimux_rx_fixup(), an SKB is allocated for each packet contained in
the URB. This SKB has too little headroom, causing the check in
skb_cow() (called from ip_forward()) to fail. pskb_expand_head() is then
called and the SKB is reallocated. In the output from perf, I see that a
significant amount of time is spent in pskb_expand_head() + support
functions.
In order to ensure that the SKB has enough headroom, this commit
increases the amount of memory allocated in qmimux_rx_fixup() by
LL_MAX_HEADER. The reason for using LL_MAX_HEADER and not a more
accurate value, is that we do not know the type of the outgoing network
interface. After making this change, I achieve the same throughput with
the modems as with the dongle.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20210106122403.1321180-1-kristian.evensen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
Fixes: c1aedf015e ("net/usb/r8153_ecm: support ECM mode for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/1394712342-15778-394-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace usbnet_get_stats64() with new identical core function
dev_get_tstats64() in all users and remove usbnet_get_stats64().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of usbnet for storing a pointer
to the per-cpu counters. This allows us to use core functionality for
statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of qmimux_priv for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support ECM mode based on cdc_ether with relative mii functions,
when CONFIG_USB_RTL8152 is not set, or the device is not supported
by r8152 driver.
Both r8152 and r8153_ecm would check the return value of
rtl8152_get_version() in porbe(). If rtl8152_get_version()
return none zero value, the r8152 is used for the device
with vendor mode. Otherwise, the r8153_ecm is used for the
device with ECM mode.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/1394712342-15778-392-Taiwan-albertk@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-28-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In set_ethernet_addr(), if get_registers() succeeds, the ethernet address
that was read must be copied over. Otherwise, a random ethernet address
must be assigned.
get_registers() returns 0 if successful, and negative error number
otherwise. However, in set_ethernet_addr(), this return value is
incorrectly checked.
Since this return value will never be equal to sizeof(node_id), a
random MAC address will always be generated and assigned to the
device; even in cases when get_registers() is successful.
Correctly modifying the condition that checks if get_registers() was
successful or not fixes this problem, and copies the ethernet address
appropriately.
Fixes: b2a0f274e3 ("net: rtl8150: Use the new usb control message API.")
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201011173030.141582-1-anant.thazhemadam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
When the router is rebooted without a power cycle, the USB device
remains connected but its configuration is reset. This results in
a non-working ethernet connection with messages like this in syslog:
usb 2-2: RX packet too long: 65535 B
Re-enable ethernet mode when receiving a packet with invalid size of
0xffff.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Obviously this driver version doesn't make sense. Go with the default
and let ethtool display the kernel version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add usb ids of the Cellient MPL200 card.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic eth_platform_get_mac_address() which can get a MAC
address from other than DT platform specific sources too. Check if the
obtained address is valid.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2:
If reading the MAC address from eeprom fail don't throw an error, use randomly
generated MAC instead. Either way the adapter will soldier on and the return
type of set_ethernet_addr() can be reverted to void.
v1:
Fix a bug in set_ethernet_addr() which does not take into account possible
errors (or partial reads) returned by its helpers. This can potentially lead to
writing random data into device's MAC address registers.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Added small note about why set_registers() can't be used to substitute
set_register().
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-2-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-3-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment above nc_vendor_write() suggests that the function could become
async so that is usable in `in_interrupt()' context or that it already is
safe to be called from such a context.
Eitherway: The function did not become async since v2.4.9.2 (2002) and it
must be not be called from `in_interrupt()' context because it sleeps on
mutltiple occations.
Remove the misleading comment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
kaweth_async_set_rx_mode() invokes kaweth_contol() and has two callers:
- kaweth_open() which is invoked from preemptible context
.
- kaweth_start_xmit() which holds a spinlock and has bottom halfs disabled.
If called from kaweth_start_xmit() kaweth_async_set_rx_mode() obviously
cannot block, which means it can't call kaweth_control(). This is detected
with an in_interrupt() check.
Replace the in_interrupt() check in kaweth_async_set_rx_mode() with an
argument which is set true by the caller if the context is safe to sleep,
otherwise false.
Now kaweth_control() is only called from preemptible context which means
there is no need for GFP_ATOMIC allocations anymore. Replace it with
usb_control_msg(). Cleanup the code a bit while at it.
Finally remove kaweth_control() since the last user is gone.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kaweth_control() is almost the same as usb_control_msg() except for the
memory allocation mode (GFP_ATOMIC vs GFP_NOIO) and the in_interrupt()
check.
All the invocations of kaweth_control() are within the probe function in
fully preemtible context so there is no reason to use atomic allocations,
GFP_NOIO which is used by usb_control_msg() is perfectly fine.
Replace kaweth_control() invocations from probe with usb_control_msg().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based MCT U3-A9003 USB
3.0 ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the missing .stop entry in the Belkin driver_info structure.
Fixes: e20bd60bf6 ("net: usb: asix88179_178a: Add support for the Belkin B2B128")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based Toshiba USB 3.0
ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Keenetic Plus DSL is a xDSL modem that uses dm9620 as its USB interface.
Signed-off-by: Kamil Lorenc <kamil@re-ws.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, each PHY has their own configuration and it can be done
through an external PHY driver. The smsc95xx driver uses only the
hard-coded internal PHY configuration.
This patch adds phylib support to probe external PHY drivers for
configuring external PHYs.
The MDI-X configuration for the internal PHYs moves from
drivers/net/usb/smsc95xx.c to drivers/net/phy/smsc.c.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using `void *driver_priv` instead of `unsigned long data[]` is more
straightforward way to recover the `struct smsc95xx_priv *` from the
`struct net_device *`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes arguments netdev and phy_id from the functions
smsc95xx_mdio_read_nopm and smsc95xx_mdio_write_nopm. Both removed
arguments are recovered from a new argument `struct usbnet *dev`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If USB_NET_CDC_NCM is y and USB_NET_CDCETHER is m, build fails:
drivers/net/usb/cdc_ncm.o:(.rodata+0x1d8): undefined reference to `usbnet_cdc_update_filter'
Select USB_NET_CDCETHER for USB_NET_CDC_NCM to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e10dcb1b6b ("net: cdc_ncm: hook into set_rx_mode to admit multicast traffic")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the USB device's device tree node when looking for a MAC address.
The struct device embedded into the struct net_device does not have a
device tree node attached at all.
The reason why this went unnoticed is because the system where this was
tested was one of the few development units that had its OTP programmed,
as opposed to production systems where the MAC address is stored in a
separate EEPROM and is passed via device tree by the firmware.
Reported-by: EJ Hsu <ejh@nvidia.com>
Fixes: acb6d3771a ("r8152: Use MAC address from device tree if available")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This check an inherent race. It opens a race where
an error code has already been set or cleared yet
the URB has not been given back. We cannot do
such an optimization and must unlink unconditionally.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this fails, kmalloc() will print a report including
a stack trace. There is no need for a separate complaint.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver tries to reuse code for disconnect in case
of a failed probe.
If resources need to be freed after an error in probe, the
netdev must not be freed because it has never been registered.
Fix it by telling the helper which path we are in.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
We set set_rx_mode to usbnet_cdc_update_filter provided
by cdc_ether that simply admits all multicast traffic
if there is more than one multicast filter configured.
Signed-off-by: Miguel Rodríguez Pérez <miguel@det.uvigo.gal>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver overrides the net_device_ops structure used by usbnet
to be able to hook into .ndo_change_mtu. However, the structure was
missing the .ndo_set_rx_mode field, preventing the driver from
hooking into usbnet's set_rx_mode. This patch adds the missing callback to
usbnet_set_rx_mode in net_device_ops.
Signed-off-by: Miguel Rodríguez Pérez <miguel@det.uvigo.gal>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function can be reused by other usbnet minidrivers.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the function available to other drivers, like cdc_ncm.
Signed-off-by: Miguel Rodríguez Pérez <miguel@det.uvigo.gal>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_cdc_update_filter was getting the interface number from the
usb_interface struct in cdc_state->control. However, cdc_ncm does
not initialize that structure in its bind function, but uses
cdc_ncm_ctx instead. Getting intf directly from struct usbnet solves
the problem.
Signed-off-by: Miguel Rodríguez Pérez <miguel@det.uvigo.gal>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ax88172a_unbind() fails, make sure that the return code is
less than zero so that cleanup is done properly and avoid UAF.
Fixes: a9a51bd727 ("ax88172a: fix information leak on short answers")
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reported-by: syzbot+4cd84f527bf4a10fc9c1@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: syzbot+29dc7d4ae19b703ff947@syzkaller.appspotmail.com
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:
04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000: 000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010: 0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020: 0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030: 0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040: ffff ffff ffff ffff ffff ffff ffff ffff
0x0050: ffff ffff ffff ffff ffff ffff ffff ffff
0x0060: ffff 961f
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Telit LE910C1-EUX composition
0x1031: tty, tty, tty, rmnet
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a MAC address was passed via the device tree node for the r8152
device, use it and fall back to reading from EEPROM otherwise. This is
useful for devices where the r8152 EEPROM was not programmed with a
valid MAC address, or if users want to explicitly set a MAC address in
the bootloader and pass that to the kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable status is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is being initializeed with a value that is never read
and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If you do not find the OUT endpoint, you should say so,
rather than copy the error message for the IN endpoint.
Presumably a copy and paste error.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Dell Wireless 5816e to drivers/net/usb/qmi_wwan.c
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor driver does upon failing to read a valid MAC address from
EEPROM write the netdev's address back to EEPROM and invoking a EEPROM
reload operation. Based on this we can implement the ethtool_ops
set_eeprom and provide the means to populate the EEPROM from within
Linux.
It's worth noting that ax88179_get_eeprom() will return some default
data unless the content of the EEPROM is deemed "complete", so until the
EEPROM is fully populated (e.g. by running ethtool -e | ethtool -E)
data written with ax88179_set_eeprom() will appear not to stick.
The implementation is based on asix_set_eeprom(), from asix_common.c
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pegasus' own workqueue and replace it with system_long_wq.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.
Fixes: 0fa81b304a ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block")
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet creates network interfaces with min_mtu = 0 and
max_mtu = ETH_MAX_MTU.
These values are not modified by qmi_wwan when the network interface
is created initially, allowing, for example, to set mtu greater than 1500.
When a raw_ip switch is done (raw_ip set to 'Y', then set to 'N') the mtu
values for the network interface are set through ether_setup, with
min_mtu = ETH_MIN_MTU and max_mtu = ETH_DATA_LEN, not allowing anymore to
set mtu greater than 1500 (error: mtu greater than device maximum).
The patch restores the original min/max mtu values set by usbnet after a
raw_ip switch.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been using the fact that the QMI and DIAG functions
usually are the only ones with class/subclass/protocol being
ff/ff/ff on Quectel modems. This has allowed us to match the
QMI function without knowing the exact interface number,
which can vary depending on firmware configuration.
The ability to silently reject the DIAG function, which is
usually handled by the option driver, is important for this
method to work. This is done based on the knowledge that it
has exactly 2 bulk endpoints. QMI function control interfaces
will have either 3 or 1 endpoint. This rule is universal so
the quirk condition can be removed.
The fixed layouts known from the Gobi1k and Gobi2k modems
have been gradually replaced by more dynamic layouts, and
many vendors now use configurable layouts without changing
device IDs. Renaming the class/subclass/protocol matching
macro makes it more obvious that this is now not Quectel
specific anymore.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f25e1392fd removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fd ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device 0xa387 also supports MAC passthrough, therefore add it to the
whitelst.
BugLink: https://bugs.launchpad.net/bugs/1827961/comments/30
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function, and
while we're at it, we can remove a null write to skb->next by replacing
it with skb_mark_not_on_list.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_linearize() fails, we need to free the skb.
TSO makes skb bigger, and this bug might be the reason
Raspberry Pi 3B+ users had to disable TSO.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use __func__ to print the function name instead of hard coded string.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Display the return code as decimal integer.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6 ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
This patch corrects the SPDX License Identifier style in
header files related to drivers for USB Network devices.
This patch gives an explicit block comment to the
SPDX License Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the use of SW timestamping.
ax88179_178a uses the usbnet transmit function usbnet_start_xmit() which
implements software timestamping. ax88179_178a overrides ethtool_ops but
missed to set .get_ts_info. This caused SOF_TIMESTAMPING_TX_SOFTWARE
capability to be not available.
Signed-off-by: Andreas K. Besslein <besslein.andreas@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 8481141246 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
