Fix the following coccicheck warning:
./drivers/net/phy/at803x.c:493:5-10: WARNING: Unsigned expression
compared with zero: value < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/1635325191-101815-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixed warning: Function parameter or member 'enable' not
described in 'genphy_c45_fast_retrain'
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211026102957.17100-1-luoj@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the network device supplies a supported interface bitmap, we can use
that during phylink's validation to simplify MAC drivers in two ways by
using the supported_interfaces bitmap to:
1. reject unsupported interfaces before calling into the MAC driver.
2. generate the set of all supported link modes across all supported
interfaces (used mainly for SFP, but also some 10G PHYs.)
Suggested-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To perform CDT of qca8081 phy:
1. disable hibernation.
2. force phy working in MDI mode.
3. force phy working in 1000BASE-T mode.
4. configure the related thresholds.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. The master/slave seed needs to be updated when the link can't
be created.
2. The case where two qca8081 PHYs are connected each other and
master/slave seed is generated as the same value also needs
to be considered, so adding this code change into read_status
instead of link_change_notify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 phy is a single port phy, configure
phy the lower seed value to make it linked as slave
mode easier.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the qca8081 phy driver config_init function, which includes:
1. Enable fast restrain.
2. Add 802.3az configurations.
3. Initialize ADC threshold as 100mv.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse at803x phy driver config_aneg excepting
adding 2500M auto-negotiation.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the at803x phy driver get_features excepting
adding 2500M capability.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Separate the function at803x_read_specific_status from
the at803x_read_status, since it can be reused by the
read_status of qca8081 phy driver excepting adding the
2500M speed.
2. Add the qca8081 read_status function qca808x_read_status.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 is a single port ethernet phy chip that supports
10/100/1000/2500 Mbps mode.
Add the basic phy driver features, and reuse the at803x
phy driver functions.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GENMASK() for the current speed value.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol feature is controlled by the MMD3.8012 bit5,
need to set this bit when the wol function is enabled.
The reg18 bit0 is for enabling WOL interrupt, when wol
occurs, the wol interrupt status reg19 bit0 is set to 1.
Call phy_trigger_machine if there are any other interrupt
pending in the function set_wol.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert at803x_set_wol to use phy_modify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->dev_addr will become a const soon(ish),
constify the local variables referring to it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ea269a6f72 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8365MB-VC ethernet switch controller has 4 internal PHYs for its
user-facing ports. All that is needed is to let the PHY driver core
pick up the IRQ made available by the switch driver.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY driver dp83867 has rich supports for OF-platform to fine-tune the PHY
chip during phy configuration. However, for non-OF platform, certain PHY
tunable parameters such as IO impedance and RX & TX internal delays are
critical and should be initialized to its default during PHY driver probe.
Tested-by: Clement <clement@intel.com>
Signed-off-by: Lay, Kuan Loon <kuan.loon.lay@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211013065941.2124858-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Give a name to known debug regs from Documentation instead of using
unknown hex values.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.
Fixes: b4df02b562 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.
Fixes: 15b9df4ece ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.
Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.
This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLIB device drivers must match by either numerical PHY ID or by their
.match_phy_device method. Matching by DT is not permitted.
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MDIO bus, we have PHYLIB devices and drivers, and we have non-
PHYLIB devices and drivers. PHYLIB devices are MDIO devices that are
wrapped with a struct phy_device.
Trying to bind a MDIO device with a PHYLIB driver results in out-of-
bounds accesses as we attempt to access struct phy_device members. So,
let's prevent this by ensuring that the type of the MDIO device
(indicated by the MDIO_DEVICE_FLAG_PHY flag) matches the type of the
MDIO driver (indicated by the MDIO_DEVICE_IS_PHY flag.)
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting
a new value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change
event notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup
on device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly
respond to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it
only in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xzZg
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from xfrm, bpf, netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with
nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change event
notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup on
device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly respond
to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it only
in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the embedded fast-ethernet PHY found on the QCA9561
WiSoC platform. It supports the usual Atheros PHY featureset including
the cable tester.
Tested on a Xiaomi MiRouter 4Q (QCA9561)
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20211005225401.10653-1-mail@david-bauer.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The string should be "tx_disable" to match the state enum.
Fixes: 4005a7cb4f ("net: phy: sftp: print debug message with text, not numbers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has
been reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYVmC1A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfCQCgtQ0kdPoPdUG6mPCn45rrbJQLBY4AnRL5JyhO
zB60l6C2EHHnLnRxMnQq
=gygB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has been
reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues"
* tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: also call kernfs_set_rev() for positive dentry
driver core: Add debug logs when fwnode links are added/deleted
driver core: Create __fwnode_link_del() helper function
driver core: Set deferred probe reason when deferred by driver core
net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents
driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD
driver core: fw_devlink: Improve handling of cyclic dependencies
cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf
debugfs: debugfs_create_file_size(): use IS_ERR to check for error
Syzbot reported memory leak in MDIO bus interface, the problem was in
wrong state logic.
MDIOBUS_ALLOCATED indicates 2 states:
1. Bus is only allocated
2. Bus allocated and __mdiobus_register() fails, but
device_register() was called
In case of device_register() has been called we should call put_device()
to correctly free the memory allocated for this device, but mdiobus_free()
calls just kfree(dev) in case of MDIOBUS_ALLOCATED state
To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED
_before_ calling device_register(), because put_device() should be
called even in case of device_register() failure.
Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/
Fixes: 46abc02175 ("phylib: give mdio buses a device tree presence")
Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit ab609f25d1.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/
Acked-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the downshift tunable for the Marvell 88x3310 PHY.
Downshift is only usable with firmware 0.3.5.0 and later.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a69 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8804 PHY has same features as that of LAN8814 PHY except that it
doesn't support 1588, SyncE or Q-USGMII.
This PHY is found inside the LAN966X switches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPY115 need reset PHY when it comes out from loopback mode if the firmware
version number (lower 8 bits) is equal to or below 0x76.
Fixes: 7d901a1e87 ("net: phy: add Maxlinear GPY115/21x/24x driver")
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are many instances of PHYs that depend on a switch to supply a
resource (Eg: interrupts). Switches also expects the PHYs to be probed
by their specific drivers as soon as they are added. If that doesn't
happen, then the switch would force the use of generic PHY drivers for
the PHY even if the PHY might have specific driver available.
fw_devlink=on by design can cause delayed probes of PHY. To avoid, this
we need to set the FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for the switch's
fwnode before the PHYs are added. The most generic way to do this is to
set this flag for the parent of MDIO busses which is typically the
switch.
For more context:
https://lore.kernel.org/lkml/YTll0i6Rz3WAAYzs@lunn.ch/#t
Fixes: ea718c6990 ("Revert "Revert "driver core: Set fw_devlink=on by default""")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210915170940.617415-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we enable APD and DLL/RXC/TXC disable we need to use
bcm54xx_suspend() in order not to do a read/modify/write of the BMCR
register which is incompatible with the desired settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two Ethernet PHYs support IDDQ-SR therefore wire-up the suspend
and resume callbacks to point to bcm54xx_suspend() and bcm54xx_resume().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for putting the PHY into IDDQ Soft Recovery mode by setting
the TOP_MISC register bits accordingly. This requires us to implement a
custom bcm54xx_suspend() routine which diverges from genphy_suspend() in
order to configure the PHY to enter IDDQ with software recovery as well
as avoid doing a read/modify/write on the BMCR register.
Doing a read/modify/write on the BMCR register means that the
auto-negotation bit may remain which interferes with the ability to put
the PHY into IDDQ-SR mode. We do software reset upon suspend in order to
put the PHY back into its state prior to suspend as recommended by the
datasheet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spacing and improve name for 83xx phy following other phy in the
same driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resume/suspend function to qca83xx internal phy.
We can't use the at803x generic function as the documentation lacks of
any support for WoL regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For qca8327 internal phy there are 2 different switch variant with 2
different phy id. Add this missing variant so the internal phy can be
correctly identified and fixed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter points out that we have a code path that permits a NULL
netdev pointer to be passed to netif_carrier_off(), which will cause
a kernel oops. In any case, we need to set pl->old_link_state to false
to have the desired effect when there is no netdev present.
Fixes: f97493657c ("net: phylink: add suspend/resume support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
72165 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
create a new macro and set of functions for this different process type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210917181551.2836036-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable the DAC early wake when then link operates at 10BaseT allows
power savings in the hundreds of milli Watts by shutting down the
transmitter. A number of errata have been issued for various Gigabit
PHYs and the recommendation is to enable both the early and forced DAC
wake to be on the safe side. This needs to be done dynamically based
upon the link state, which is why a link_change_notify callback is
utilized.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210916212742.1653088-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 3ac8eed625, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Fixes: 3ac8eed625 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently changes to the advertising state via ethtool do not cause any
reselection of the configured interface mode after the SFP is already
inserted and initially configured.
While it is not typical to change the advertised link modes for an
interface using an SFP in certain use cases it is desirable. In the case
of a SFP port that is capable of handling both SFP and SFP+ modules it
will automatically select between 1G and 10G modes depending on the
supported mode of the SFP. However if the SFP module is capable of
working in multiple modes (e.g. a SFP+ DAC that can operate at 1G or
10G), one end of the cable may be attached to a SFP 1000base-x port thus
the SFP+ end must be manually configured to the 1000base-x mode in order
for the link to be established.
This change causes the ethtool setting of advertised mode changes to
reselect the interface mode so that the link can be established.
Additionally when a module is inserted the advertising mode is reset to
match the supported modes of the module.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang reports that Wake-on-Lan with the stmmac ethernet driver broke
when moving the incorrect handling of mac link state out of mac_config().
This reason this breaks is because the stmmac's WoL is handled by the MAC
rather than the PHY, and phylink doesn't cater for that scenario.
This patch adds the necessary phylink code to handle suspend/resume events
according to whether the MAC still needs a valid link or not. This is the
barest minimum for this support.
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Tested-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling interrupts via device tree for the internal PHYs on the
mv88e6390 DSA switch does not work. The driver insists to use poll mode.
Stage one debugging shows that the fwnode_mdiobus_phy_device_register
function calls fwnode_irq_get properly, and phy->irq is set to a valid
interrupt line initially.
But it is then cleared.
Stage two debugging shows that it is cleared here:
phy_probe:
/* Disable the interrupt if the PHY doesn't support it
* but the interrupt is still a valid one
*/
if (!phy_drv_supports_irq(phydrv) && phy_interrupt_is_valid(phydev))
phydev->irq = PHY_POLL;
Okay, so does the "Marvell 88E6390 Family" PHY driver not have the
.config_intr and .handle_interrupt function pointers? Yes it does.
Stage three debugging shows that the PHY device does not attempt a probe
against the "Marvell 88E6390 Family" driver, but against the "mv88x3310"
driver.
Okay, so why does the "mv88x3310" driver match on a mv88x6390 internal
PHY? The PHY IDs (MARVELL_PHY_ID_88E6390_FAMILY vs
MARVELL_PHY_ID_88X3310) are way different.
Stage four debugging has us looking through:
phy_device_register
-> device_add
-> bus_probe_device
-> device_initial_probe
-> __device_attach
-> bus_for_each_drv
-> driver_match_device
-> drv->bus->match
-> phy_bus_match
Okay, so as we said, the MII_PHYSID1 of mv88e6390 does not match the
mv88x3310 driver's PHY mask & ID, so why would phy_bus_match return...
Ahh, phy_bus_match calls a shortcircuit method,
phydrv->match_phy_device, and does not even bother to compare the PHY ID
if that is implemented.
So of course, we go inside the marvell10g.c driver and sure enough, it
implements .match_phy_device and does not bother to check the PHY ID.
What's interesting though is that at the end of the device_add() from
phy_device_register(), the driver for the internal PHYs _is_ the proper
"Marvell 88E6390 Family". This is because "mv88x3310" ends up failing to
probe after all, and __device_attach_driver(), to quote:
/*
* Ignore errors returned by ->probe so that the next driver can try
* its luck.
*/
The next (and only other) driver that matches is the 6390 driver. For
this one, phy_probe doesn't fail, and everything expects to work as
normal, EXCEPT phydev->irq has already been cleared by the previous
unsuccessful probe of a driver which did not implement PHY interrupts,
and therefore cleared that IRQ.
Okay, so it is not just Marvell 6390 that has PHY interrupts broken.
Stuff like Atheros, Aquantia, Broadcom, Qualcomm work because they are
lexicographically before Marvell, and stuff like NXP, Realtek, Vitesse
are broken.
This goes to show how fragile it is to reset phydev->irq = PHY_POLL from
the actual beginning of phy_probe itself. That seems like an actual bug
of its own too, since phy_probe has side effects which are not restored
on probe failure, but the line of thought probably was, the same driver
will attempt probe again, so it doesn't matter. Well, looks like it
does.
Maybe it would make more sense to move the phydev->irq clearing after
the actual device_add() in phy_device_register() completes, and the
bound driver is the actual final one.
(also, a bit frightening that drivers are permitted to bypass the MDIO
bus matching in such a trivial way and perform PHY reads and writes from
the .match_phy_device method, on devices that do not even belong to
them. In the general case it might not be guaranteed that the MDIO
accesses one driver needs to make to figure out whether to match on a
device is safe for all other PHY devices)
Fixes: a5de4be0aa ("net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210827132541.28953-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Configure speed if loopback is used. read_status is not called for
loopback.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct phy_device contains a pointer to the PHY driver and nearly
everywhere this pointer is used to access the PHY driver. Only
mdio_bus_phy_may_suspend() is still using to_phy_driver() instead of the
PHY driver pointer. Uniform PHY driver access by eliminating
to_phy_driver() use in mdio_bus_phy_may_suspend().
Only phy_bus_match() and phy_probe() are still using to_phy_driver(),
because PHY driver pointer is not available there.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_read_status and various other PHY functions support PHY specific
overriding of driver functions by using a PHY specific pointer to the
PHY driver. Add support of PHY specific override to phy_loopback too.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Wake-on-PHY feature support by enabling the Link Up Event.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for SFP cages connected to the Marvell 88E1512 transceiver.
88E1512 supports for SGMII/1000Base-X/100Base-FX media type with RGMII
on system interface. Configure PHY to appropriate mode depending on the
type of SFP inserted. On SFP removal configure PHY to the RGMII-copper
mode so RJ-45 port can still work.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/20210812134256.2436-1-i.bornyakov@metrotek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TJA1102 provides interrupt notification for the critical health states
like overtemperature and undervoltage.
The overtemperature bit is set if package temperature is beyond 155C°.
This functionality was tested by heating the package up to 200C°
The undervoltage bit is set if supply voltage drops beyond some critical
threshold. Currently not tested.
In a typical use case, both of this events should be logged and stored
(or send to some remote system) for further investigations.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5e63c7d38 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate arrays on the stack but instead them static const.
Makes the object code smaller by 280 bytes.
Before:
text data bss dec hex filename
24142 4368 192 28702 701e ./drivers/net/phy/mscc/mscc_ptp.o
After:
text data bss dec hex filename
23830 4400 192 28422 6f06 ./drivers/net/phy/mscc/mscc_ptp.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210801070155.139057-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic for discerning between KSZ8051 and KSZ87XX PHYs is incorrect
such that the that KSZ87XX switch is not identified correctly.
ksz8051_ksz8795_match_phy_device() uses the parameter ksz_phy_id
to discriminate whether it was called from ksz8051_match_phy_device()
or from ksz8795_match_phy_device() but since PHY_ID_KSZ87XX is the
same value as PHY_ID_KSZ8051, this doesn't work.
Instead use a bool to discriminate the caller.
Without this patch, the KSZ8795 switch port identifies as:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Generic PHY]
With the patch, it identifies correctly:
ksz8795-switch spi3.1 ade1 (uninitialized): PHY [dsa-0.1:03] driver [Micrel KSZ87XX Switch]
Fixes: 8b95599c55 ("net: phy: micrel: Discern KSZ8051 and KSZ8795 PHYs")
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore PHY_ID_BCM54811 accidently removed by commit 5d4358ede8.
Fixes: 5d4358ede8 ("net: phy: broadcom: Allow BCM54210E to configure APD")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate the follow versioncheck warning:
./drivers/net/phy/mxl-gpy.c: 9 linux/version.h not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit was probably not tested on net-next, since it did not
refactor the extra phy id check introduced in commit b856150c80 ("net:
phy: at803x: mask 1000 Base-X link mode").
Fixes: 8887ca5474 ("net: phy: at803x: simplify custom phy id matching")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to fiddle about with the supported mask after we have
validated the user's requested parameters. Simplify and streamline the
code by moving the linkmode copy and update of the autoneg bit after
validating the user's request.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the possibility to configure the RGMII RX/TX clock skew via
devicetree.
Simply set phy mode to "rgmii-id", "rgmii-rxid" or "rgmii-txid" and add
the "rx-internal-delay-ps" or "tx-internal-delay-ps" property to the
devicetree.
Furthermore, a warning is now issued if the phy mode is configured to
"rgmii" and an internal delay is set in the phy (e.g. by pin-strapping),
as in the dp83867 driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augment the phy link debug prints with the pause state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver to support the Maxlinear GPY115, GPY211, GPY212, GPY215,
GPY241, GPY245 PHYs. Separate from XWAY PHY driver because this series
has different register layout and new features not supported in XWAY PHY.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Acked-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
