Switch to the net core rx/tx byte/packet counter infrastructure.
This simplifies the code, only small drawback is some memory overhead
because we use just one queue, but allocate the counters per cpu.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes: 424a646e07 ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For several network drivers it was reported that using
__napi_schedule_irqoff() is unsafe with forced threading. One way to
fix this is switching back to __napi_schedule, but then we lose the
benefit of the irqoff version in general. As stated by Eric it doesn't
make sense to make the minimal hard irq handlers in drivers using NAPI
a thread. Therefore ensure that the hard irq handler is never
thread-ified.
Fixes: 9a899a35b0 ("r8169: switch to napi_schedule_irqoff")
Link: https://lkml.org/lkml/2020/10/18/19
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4d3ef84a-c812-5072-918a-22a6f6468310@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that system freezes on r8169 driver load on a system
using ether_clk. The original change was done under the assumption
that the clock isn't needed for basic operations like chip register
access. But obviously that was wrong.
Therefore effectively revert the original change, and in addition
leave the clock active when suspending and WoL is enabled. Chip may
not be able to process incoming packets otherwise.
Fixes: 9f0b54cd16 ("r8169: move switching optional clock on/off to pll power functions")
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver.
Fixes: a7a92cf815 ("r8169: sync PCIe PHY init with vendor driver 8.047.01")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.
There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well
w/o firmware, however for a stable link at 1Gbps firmware revision
0.0.2 is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two managed helpers for mdiobus - devm_mdiobus_alloc()
and devm_mdiobus_register(). The idea behind devres is that the release
callback releases whatever resource the devm function allocates. In the
mdiobus case however there's no devres associated with the device by
devm_mdiobus_register(). Instead the release callback for
devm_mdiobus_alloc(): _devm_mdiobus_free() unregisters the device if
it is marked as managed.
This all seems wrong. The managed structure shouldn't need to know or
care about whether it's managed or not - and this is the case now for
struct mii_bus. The devres wrapper should be opaque to the managed
resource.
This changeset makes devm_mdiobus_alloc() and devm_mdiobus_register()
conform to common devres standards: devm_mdiobus_alloc() allocates a
devres structure and registers a callback that will call mdiobus_free().
__devm_mdiobus_register() allocated another devres and registers a
callback that will unregister the bus.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far RTL8401 was treated like a RTL8101e, means we relied on the BIOS
to configure MAC and PHY properly. Make RTL8401 a separate chip version
and copy MAC / PHY config from r8101 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip versions 13, 14, 15 are treated the same by the driver, therefore
let's merge them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek added new members to the RTL8125 chip family, therefore rename
RTL8125 to RTL8125a. Then we use the same chip naming as in the r8125
vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify rtl8169_runtime_resume() by calling rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the critical sections are protected with RTNL lock, we don't
need a separate mutex any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most relevant ops (open, close, ethtool ops) are protected with RTNL
lock by net core. Make sure that such ops can't be interrupted by
e.g. (runtime-)suspending by taking the RTNL lock in suspend ops
and the PCI error handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out bringing device up to a new function rtl8169_up(), similar
to rtl8169_down() for bringing the device down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the netdevice is marked as detached now when parent is not
accessible we can remove quite some checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the netdevice as detached whenever we go into PCI D3hot.
This allows to remove some checks e.g. from ethtool ops because
dev_ethtool() checks for netif_device_present() in the beginning.
In this context move waking up the queue out of rtl_reset_work()
because in cases where netif_device_attach() is called afterwards
the queue should be woken up by the latter function only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically the firmware takes care that tp->ocp_base is reset to its
default value. That's not the case (at least) for RTL8117.
As a result subsequent PHY access reads/writes the wrong page and
the link is broken. Fix this be resetting tp->ocp_base explicitly.
Fixes: 229c1e0dfd ("r8169: load firmware for RTL8168fp/RTL8117")
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we can not configure irq coalescing when link is down. Allow the
user to do this, and assume that he wants to configure irq coalescing
for highest speed. Otherwise the irq rate is low enough anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relevant chip clocks are disabled in rtl_pll_power_down(), therefore
move calling clk_disable_unprepare() there. Similar for enabling the
clock.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Counters are updated whenever we go down, therefore move the call to
rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() meanwhile does more than a hw reset, therefore rename
it to rtl8169_cleanup(). In addition move calling napi_disable() to this
function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() may be called under RTNL lock, therefore switch to
synchronize_net().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following scenario WoL isn't configured properly:
- Driver is loaded, interface isn't brought up within 10s, so driver
runtime-suspends.
- WoL is set.
- Interface is brought up, stored WoL setting isn't applied.
It has always been like that, but the scenario seems to be quite
theoretical as I haven't seen any bug report yet. Therefore treat
the change as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 9d3679fe0f ("r8169: inline rtl8169_make_unusable_by_asic")
this constant isn't used any longer, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of problems it facilitates the bug analysis if we know whether
DASH is active. Therefore emit a message in probe if this is the case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Th referenced change added an extra hw reset to rtl8169_net_suspend()
what makes WoL fail on few chip versions. Therefore skip the extra
reset if we're going down and WoL is enabled.
In rtl_shutdown() rtl8169_hw_reset() is called by rtl8169_net_suspend()
already if needed, therefore avoid issues issue by removing the extra
call. The fix was tested on a system with RTL8168g.
Meanwhile rtl8169_hw_reset() does more than a hw reset and should be
renamed. But that's net-next material.
Fixes: 8ac8e8c64b ("r8169: make rtl8169_down central chip quiesce function")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify handling the power management callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call netif_napi_del() manually, free_netdev() does this for us.
In addition reorder calls to match reverse order of calls in probe().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168f/RTL8411 with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168evl with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168h with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync hw config for RTL8168g with r8168 vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mask argument as it's not used by r8168ep_ocp_read().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers read the full 32bit value, therefore the mask argument can
be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to r8168 vendor driver DASHv3 chips like RTL8168fp/RTL8117
need a special addressing for OCP access.
Fix is compile-tested only due to missing test hardware.
Fixes: 1287723aa1 ("r8169: add support for RTL8117")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In [0] a user reported reproducible tx timeouts on RTL8168f except
PktCntrDisable is set and irq coalescing is enabled.
Realtek told me that they are not aware of any related hw issue on
this chip version, therefore root cause is still unknown. It's not
clear whether the issue affects one or more chip versions in general,
or whether issue is specific to reporter's system.
Due to this level of uncertainty, and due to the fact that I'm aware
of this one report only, let's apply the workaround on net-next only.
After this change setting irq coalescing via ethtool can reliably
avoid the issue on the affected system.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=207205
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the compiler decide about inlining, and as confirmed by Eric it's
better to use WRITE_ONCE here to ensure that the descriptor ownership
is transferred to NIC immediately.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the goto from the rx error handling branch into the else branch,
and in general avoid having the main rx work in the else branch.
In addition ensure proper reverse xmas tree order of variables in the
for loop.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After having switched to devm_mdiobus_register() also this remaining
call to mdiobus_unregister() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
93882c6f21 ("r8169: switch from netif_xxx message functions to
netdev_xxx") removed the last module parameter from the driver,
therefore there's no need any longer to include linux/moduleparam.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 9de5d235b6 ("net: phy: fix aneg restart in phy_ethtool_set_eee")
we don't need the check for aneg being enabled any longer, and as
discussed with Russell configuring the EEE advertisement should be
supported even if we're in a half-duplex mode currently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync the reset preparation for chips from RTL8168g with the r8168 and
r8125 vendor drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for waiting for FIFO's to be empty, again the name is
borrowed from the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper for setting RXDV_GATED_EN, the 2ms delay is copied from
the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a helper for this waiting function, name of the helper is
borrowed from the vendor driver. In addition don't return in the two
hw_init functions if the first wait runs into a timeout, there's no
benefit in doing so.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
r8169 never had native support for the RTL8401, however it reportedly
worked with the fallback to RTL8101e [0]. Therefore let's add this
as an explicit assignment.
[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=956868
Fixes: b4cc2dcc9c ("r8169: remove default chip versions")
Reported-by: Camaleón <noelamac@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new flexible sleep function fsleep() to merge the udelay and msleep
polling functions. We can safely do this because no polling function
is used in atomic context in this driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper eth_hw_addr_crc to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Considering the few messages we have in the driver, there's not really
a benefit in being able to control them on a message type level.
Therefore simplify the code and switch to the netdev_xxx message
functions. In addition add net_ratelimit() to messages that can be
printed from a hot path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing an unrelated change, checkpatch complained about this
redundant out-of-memory message. Therefore remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter handling functions can only fail if rtl8169_do_counters()
times out. In the poll function we emit an error message in case of
timeout, therefore we don't have to propagate the timeout all the
way up just to print another message basically saying the same.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net core - __dev_set_promiscuity - prints a message already when
promiscuous mode in entered/left, therefore we don't have to do this
in the driver too. Also the driver message would be misleading
(would be because "link" message level is disabled per default)
because it would print "promisc mode enabled" even if it's being
left. Reason is that __dev_change_flags() calls dev_set_rx_mode()
before touching the promisc flag.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a not needed parameter in rtl8169_set_magic_reg.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 supports the same PME_SIGNAL handling as all later RTL8168
chip variants.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sync definition of max jumbo packet size with vendor driver and reserve
22 bytes for VLAN ethernet header plus checksum.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information about a HW constraint that time limit must
not be set to 0 if the frame limit is >0. Add a check for this and
reject invalid parameter combinations.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_PREP() to make the code better readable, and avoid the loop.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports only frame limits 0, 4, 8, .. 60 internally.
Returning EINVAL for all val % 4 != 0 seems to be a little bit too
unfriendly to the user. Therefore round up the frame limit to the next
supported value. In addition round up the time limit, else a very low
limit could be rounded down to 0, and interpreted as "ignore value"
by the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time limit provided by userspace is multiplied with 1000,
what could result in an overflow. Therefore change the time limit
parameter unit from ns to us, and avoid the problematic operation.
If there's no matching scale because provided time limit is too big,
return ERANGE instead of EINVAL to provide a hint to the user what's
wrong.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use FIELD_GET() macro to make the code better readable. In addition
change the logic to round the time limit up, not down. Reason is that
a time limit <1us would be rounded to 0 currently, what would be
interpreted as "no time limit set".
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx and tx scale are the same always. Simplify the code by using one
scale for rx and tx only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_device argument is just used to get a struct rtl8169_private
pointer via netdev_priv(). Therefore pass the struct rtl8169_private
pointer directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of consumer mainboards where the BIOS leaves the PHY
in a state that it's reporting an invalid PHY ID. To detect such cases
add the PHY ID to the error message if no dedicated PHY driver is found.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bits in RxConfig are controlled by the following dev->feature's:
- NETIF_F_RXALL
- NETIF_F_HW_VLAN_CTAG_RX (since RTL8125)
We have to take care that RxConfig gets fully configured in
rtl_hw_start() after e.g. resume from hibernation. Therefore:
- Factor out setting the feature-controlled RxConfig bits to a new
function rtl_set_rx_config_features() that is called from
rtl8169_set_features() and rtl_hw_start().
- Don't deal with RX_VLAN_8125 in rtl_init_rxcfg(), it will be set
by rtl_set_rx_config_features().
- Don't handle NETIF_F_RXALL in rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's sufficient to do the masking once in probe() for clearing
unwanted bits that may have been set by the BIOS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.
No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline rtl8169_make_unusable_by_asic() and simplify it:
- Address field doesn't need to be poisoned because descriptor is
owned by CPU now
- desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(),
therefore we don't have to preserve any field parts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been a number of reports that using SG/TSO on different chip
versions results in tx timeouts. However for a lot of people SG/TSO
works fine. Therefore disable both features by default, but allow users
to enable them. Use at own risk!
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out mapping the tx skb to a new function rtl8169_tx_map(). This
allows to remove redundancies, and rtl8169_get_txd_opts1() has only
one user left, so it can be inlined.
As a result rtl8169_xmit_frags() is significantly simplified, and in
rtl8169_start_xmit() the code is simplified and better readable.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mtu is greater than TD_MSS_MAX, then TSO is disabled, see
rtl8169_fix_features(). Because mss is less than mtu, we can't have
the case mss > TD_MSS_MAX in the TSO path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev_stats_to_stats64() do the copy work for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing opts2 belongs to preparing the descriptor for DMA engine use.
Therefore move it into rtl8169_mark_to_asic().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until ae84bc1873 ("r8169: don't use bit LastFrag in tx descriptor
after send") we used to access another bit in the descriptor, therefore
it seems the barrier was needed. Since this commit DescOwn is the
only bit we're interested in, so the barrier isn't needed any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the parameters taken by rtl8169_unmap_tx_skb, this makes
usage of this function easier to read and understand.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far tx_skb->skb is the only member of the two structs that is not
reset. Make understanding the code easier by resetting both structs
completely in rtl8169_unmap_tx_skb.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly improve the code by converting this while to a for loop.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper pci_status_get_and_clear_errors() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out PCI_STATUS error bit handling let drivers
use the same collection of error bits. To facilitate bisecting we do this
in a separate patch per affected driver. For the r8169 driver we have to
add PCI_STATUS_PARITY to the error bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only call rtl8169_xmit_frags() if the skb is actually fragmented.
This avoid a small overhead for non-fragmented skb's, and it allows
to simplify rtl8169_xmit_frags() a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These constants are used in one place only, so we can remove them and
use the values directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by using the new helper tcp_v6_gso_csum_prep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register RxMissed exists on few early chip versions only, however all
chip versions have the number of missed RX packets in the hardware
counters. Therefore remove using RxMissed and get the number of missed
RX packets from the hardware stats.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge enabling and disabling jumbo packets to one function to make
the code a little simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently code snippet (RTL_R32(tp, TxConfig) >> 20) & 0xfcf is used
in few places to extract the chip XID. Change the code to do the XID
extraction only once.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In few places we do a PCI commit by reading an arbitrary chip register.
It's not always obvious that the read is meant to be a PCI commit,
therefore add a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev->features a few lines later allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done for all RTL8169 chip versions in rtl8169_init_phy already.
Therefore we can remove it here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_link_chg_patch() can be called from rtl_open() to rtl8169_close()
only. And in rtl8169_close() phy_stop() ensures that this function
isn't called afterwards. So we don't need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d3654 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defaults for min_mtu and max_mtu are set by ether_setup(), which is
called from devm_alloc_etherdev(). Let rtl_jumbo_max() only return
a positive value if actually jumbo packets are supported. This also
allows to remove constant Jumbo_1K which is a little misleading anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl8169_ioctl with new generic function phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move chip-specific PHY configurations to separate source file
r8169_phy_config.c. This improves maintainability of the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out PHY configuration to a separate source
file move commonly used definitions to new header file r8169.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename rtl_apply_firmware() to r8169_apply_firmware() before exporting
it to avoid namespace clashes with other drivers for Realtek hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the phy_device as parameter to rtl8168d_apply_firmware_cond(),
this avoids having to access rtl8169_private internals.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl_writephy and rtl_readphy with the respective phylib
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move configuring EEE on MAC side out of the PHY configuration.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing this ERI register is a MAC setting, so move it to
rtl_hw_start_8106().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch rtl_writephy_batch() to phylib functions, as a result we can
avoid passing a rtl8169_private parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions use only the phy_device member of rtl8169_private,
so we can pass the phy_device as parameter directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of factoring out rtl8169scd_hw_phy_config() move this
quirk to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless debug statement. This also allows to remove the
net_device parameter from rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preperation of factoring out the PHY configuration to a separate
source file this patch:
- avoids accessing rtl8169_private internals by passing the phy_device
and mac_version as separate parameters
- renames rtl_hw_phy_config to r8169_hw_phy_config to avoid namespace
clashes with other drivers for Realtek hardware
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use constant EnAnaPLL for bit 14 as in vendor driver. The vendor
driver sets this bit for chip version 02 only, but I'm not aware of
any issues, so better leave it as it is.
In addition remove the useless debug message.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by moving the call to rtl_enable_eee() from the
individual PHY configs to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to recent changes we don't need the call to rtl_rar_exgmac_set()
and longer at this place. It's called from rtl_rar_set() which is
called in rtl_init_mac_address() and rtl8169_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and factor out this magic from rtl8168h_2_hw_phy_config()
and name it based on the vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3b ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
