We have code in the ice driver which allocates the pin_config structure
if n_pins is > 0, but we never set n_pins to be greater than zero.
There's no reason to keep this code until we actually have pin_config
support. Remove this. We can re-add it properly when we implement
support for pin_config for E810-T devices.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver accidentally copied the ice_for_each_rxq iterator when
implementing enablement of the ptp_tx bit for the Tx rings. We still
load the Tx rings and set the ptp_tx field, but we iterate over the
count of the num_rxq.
If the number of Tx and Rx queues differ, this could either cause
a buffer overrun when accessing the tx_rings list if num_txq is greater
than num_rxq, or it could cause us to fail to enable Tx timestamps for
some rings.
This was not noticed originally as we generally have the same number of
Tx and Rx queues.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enables PCIe PTM (Precision Time Measurement) support in the igc
driver. Notifies the PCI devices that PCIe PTM should be enabled.
PCIe PTM is similar protocol to PTP (Precision Time Protocol) running
in the PCIe fabric, it allows devices to report time measurements from
their internal clocks and the correlation with the PCIe root clock.
The i225 NIC exposes some registers that expose those time
measurements, those registers will be used, in later patches, to
implement the PTP_SYS_OFFSET_PRECISE ioctl().
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213667
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23 ("e1000e: add support for LTR on I217/I218")
Suggested-by: Yee Li <seven.yi.lee@gmail.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437 ("igc: Add support for taprio offloading")
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Check PCI state to remove device safely.
Trace:
BUG: unable to handle page fault for address: 000000000000b604
Oops: 0000 [#1] SMP NOPTI
RIP: 0010:igc_rd32+0x1c/0x90 [igc]
Call Trace:
igc_ptp_suspend+0x6c/0xa0 [igc]
igc_ptp_stop+0x12/0x50 [igc]
igc_remove+0x7f/0x1c0 [igc]
pci_device_remove+0x3e/0xb0
__device_release_driver+0x181/0x240
Fixes: 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
Fixes: b03c49cde6 ("igc: Save PTP time before a reset")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e0 ("iavf: fix MAC address setting for VFs when filter is rejected")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <Gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886 ("i40e: Fix queue-to-TC mapping on Tx")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails,
We should restore the previous state and clean up the
resources. Add the missing clear af_xdp_zc_qps and unmap dma
to fix this bug.
Fixes: d49e286d35 ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair")
Fixes: 4a9b32f30f ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As follow-up to the discussion with Jakub Kicinski about iavf locking
being insufficient [1] convert iavf to use mutexes instead of bitops.
The locking logic is kept as is, just a drop-in replacement of
enum iavf_critical_section_t with separate mutexes.
The only difference is that the mutexes will be destroyed before the
module is unloaded.
[1] https://lwn.net/ml/netdev/20210316150210.00007249%40intel.com/
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Internal tests found out that the latest code doesn't bring up 1PPS out
as expected. As a result of incorrect define used to round the time up
the time was round down to the past second boundary.
Fix define used for rounding to properly round up to the next Top of
second in ice_ptp_cfg_clkout to fix it.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210813165018.2196013-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
iavf driver should set RSS LUT and key unconditionally in reset
path. Currently, the driver does not do that. This patch fixes
this issue.
Fixes: 2c86ac3c70 ("i40evf: create a generic config RSS function")
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When VFs are setup and torn down in quick succession, it is possible
that a VF is torn down by the PF while the VF's virtchnl requests are
still in the PF's mailbox ring. Processing the VF's virtchnl request
when the VF itself doesn't exist results in undefined behavior. Fix
this by adding a check to stop processing virtchnl requests when VF
teardown is in progress.
Fixes: ddf30f7ff8 ("ice: Add handler to configure SR-IOV")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add failed_counter to i21x_doublecheck(). There is possibility that
loop will never end.
With this patch the loop will stop after maximum 3 retries
to write to MTA_REGISTER
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix missing failed message if driver does not have enough queues to
complete TC command. Without this fix no message is displayed in dmesg.
Fixes: a9ce82f744 ("i40e: Enable 'channel' mode in mqprio for TC configs")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In SW DCB mode the packets sent receive incorrect UP tags. They are
constructed correctly and put into tx_ring, but UP is later remapped by
HW on the basis of TCTUPR register contents according to Tx queue
selected, and BW used is consistent with the new UP values. This is
caused by Tx queue selection in kernel not taking into account DCB
configuration. This patch fixes the issue by implementing the
ndo_select_queue NDO callback.
Fixes: fd0a05ce74 ("i40e: transmit, receive, and NAPI")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of PHY type error occurs, the message was too generic.
Add additional info to PHY type error indicating that it can be
wrong cable connected.
Fixes: 124ed15bf1 ("i40e: Add dual speed module support")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d0704 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct the message flow between driver and firmware when disabling
queues.
Previously in case of PF reset (due to required reinit after reconfig),
the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up
occasionally. The error was not a real issue of hardware or firmware,
it was caused by wrong sequence of messages invoked by the driver.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the cycle time is set to maximum of 1s, the TX Hang timeout need to
be increase to avoid possible TX Hang.
There is no dedicated number specific in data sheet for the timeout factor.
Timeout factor was determined during the debugging to solve the "Tx Hang"
issues that happen in some cases mainly during ETF(Earliest TxTime First).
This can be test by using TSN Schedule Tx Tools udp_tai sample application.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
According to datasheet section 8.12.19, when there's no TSN offloading
Shadow_QbvCycle bit[29:0] must be set to zero for basic scheduling.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one phy->type: copper. There is no point checking
phy->type during the igc_has_link method from the watchdog that
invoked every 2 seconds.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices have only one PHY vendor. There is no point checking
_I_PHY_ID during the link establishment and auto-negotiation process.
This patch comes to clean up these pointless checkings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a spelling mistake in the comment block.
Signed-off-by: Tree Davies <tdavies@darkphysics.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Minor fixes to allow debug prints more readable.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platforms
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be
available on the next Intel Client platform (Lunar Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After transferring the MAC-PHY interface to the SMBus set the PHY
to S0ix low power idle mode.
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Per guidance from the CSME architecture team, it may take
up to 1 second for unconfiguring dynamic power gating mode.
Practically it can take more time. Wait up to 2.5 seconds to indicate
dynamic power gating exit from the S0ix configuration. Detect
scenarios that take more than 1 second but less than 2.5 seconds
will emit warning message.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On the corporate system, the driver will ask from the CSME
(manageability engine) to perform device settings are required
to allow S0ix residency.
This patch provides initial support.
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Julian Wiedmann says:
====================
s390/qeth: updates 2021-07-20
please apply the following patch series for qeth to netdev's net-next tree.
This removes the deprecated support for OSN-mode devices, and does some
follow-on cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cf8331825a.
There are better Linux interfaces to export the different LED modes
and blinking reasons.
Revert this patch for now and come up with better solution later.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210719101640.16047-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_config_vf_promiscuous_mode() calls
i40e_getnum_vf_vsi_vlan_filters() without acquiring the
mac_filter_hash_lock spinlock.
This is unsafe because mac_filter_hash may get altered in another thread
while i40e_getnum_vf_vsi_vlan_filters() traverses the hashes.
Simply adding the spinlock in i40e_getnum_vf_vsi_vlan_filters() is not
possible as it already gets called in i40e_get_vlan_list_sync() with the
spinlock held. Therefore adding a wrapper that acquires the spinlock and
call the correct function where appropriate.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Fix-suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Each i225 has three LEDs. Export them via the LED class framework.
Each LED is controllable via sysfs. Example:
$ cd /sys/class/leds/igc_led0
$ cat brightness # Current Mode
$ cat max_brightness # 15
$ echo 0 > brightness # Mode 0
$ echo 1 > brightness # Mode 1
The brightness field here reflects the different LED modes ranging
from 0 to 15.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently flex filters are only used for filters containing user data.
However, it makes sense to utilize them also for filters having
multiple conditions, because that's not supported by the driver at the
moment. Add it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allows Flex Filters to be installed.
The previous restriction to the types of filters that can be installed
can now be lifted.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex filter mechanism to extend the current ethtool filter
operations by intercoperating the user data. This allows to match
eight more bytes within a Ethernet frame in addition to macs, ether
types and vlan.
The matching pattern looks like this:
* dest_mac [6]
* src_mac [6]
* tpid [2]
* vlan tci [2]
* ether type [2]
* user data [8]
This can be used to match Profinet traffic classes by FrameID range.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel i225 NIC has the possibility to add flex filters which can
match up to the first 128 byte of a packet. These filters are useful
for all kind of packet matching. One particular use case is Profinet,
as the different traffic classes are distinguished by the frame id
range which cannot be matched by any other means.
Add code to configure and enable flex filters.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets
in subflow receive buffers longer than necessary, delaying
MPTCP-level ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack: do not renew entry stuck in tcp SYN_SENT state
- netfilter: conntrack: do not mark RST in the reply direction coming
after SYN packet for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmDu3mMACgkQMUZtbf5S
Irsjxg//UwcPJMYFmXV+fGkEsWYe1Kf29FcUDEeANFtbltfAcIfZ0GoTbSDRnrVb
HcYAKcm4XRx5bWWdQrQsQq/yiLbnS/rSLc7VRB+uRHWRKl3eYcaUB2rnCXsxrjGw
wQJgOmztDCJS4BIky24iQpF/8lg7p/Gj2Ih532gh93XiYo612FrEJKkYb2/OQfYX
GkbnZ0kL2Y1SV+bhy6aT5azvhHKM4/3eA4fHeJ2p8e2gOZ5ni0vpX0xEzdzKOCd0
vwR/Wu3h/+2QuFYVcSsVguuM++JXACG8MAS/Tof78dtNM4a3kQxzqeh5Bv6IkfTu
rokENLq4pjNRy+nBAOeQZj8Jd0K0kkf/PN9WMdGQtplMoFhjjV25R6PeRrV9wwPo
peozIz2MuQo7Kfof1D+44h2foyLfdC28/Z0CvRbDpr5EHOfYynvBbrnhzIGdQp6V
xgftKTOdgz2Djgg8HiblZund1FA44OYerddVAASrIsnSFnIz1VLVQIsfV+GLBwwc
FawrIZ6WfIjzRSrDGOvDsbAQI47T/1jbaPJeK6XgjWkQmjEd6UtRWRZLYCxemQEw
4HP3sWC96BOehuD8ylipVE1oFqrxCiOB/fZxezXqjo8dSX3NLdak4cCHTHoW5SuZ
eEAxQRaBliKd+P7hoy9cZ57CAu3zUa8kijfM5QRlCAHF+zSxaPs=
=QFnb
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
This PR contains a replacement driver for Intel iWarp hardware. This new
driver supports the old ethernet hardware and also newer chips that can do
ROCE. Otherwise this contains the typical mix of patches:
- Driver updates and cleanups for bnxt_re, cxgb4, mlx4, and mlx5
- Many static checker driven code clean ups, including a wide refcount_t
conversion
- Several series for the hns driver, more HIP09 HW capabilities, migration
to new HW register manipulators, and code cleanups
- Minor fixes and improvements in srp, rts, and cm
- Improvements throughout for sysfs related code to use DEVICE_ATTR_*,
make the ib_port sysfs first-class, and overall use sysfs APIs properly
- Intel's new irdma driver replacing i40iw
- rxe general clean ups and Memory Window support
-----BEGIN PGP SIGNATURE-----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=wyqt
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This contains a replacement driver for Intel iWarp hardware. This new
driver supports the old ethernet hardware and also newer chips that
can do ROCE.
Other than that, this contains the typical mix of patches:
- Driver updates and cleanups for bnxt_re, cxgb4, mlx4, and mlx5
- Many static checker driven code clean ups, including a wide
refcount_t conversion
- Several series for the hns driver, more HIP09 HW capabilities,
migration to new HW register manipulators, and code cleanups
- Minor fixes and improvements in srp, rts, and cm
- Improvements throughout for sysfs related code to use
DEVICE_ATTR_*, make the ib_port sysfs first-class, and overall use
sysfs APIs properly
- Intel's new irdma driver replacing i40iw
- rxe general clean ups and Memory Window support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (211 commits)
RDMA/core: Always release restrack object
RDMA/mlx5: Don't access NULL-cleared mpi pointer
RDMA/irdma: Fix potential overflow expression in irdma_prm_get_pbles
RDMA/irdma: Check contents of user-space irdma_mem_reg_req object
RDMA/rxe: Missing unlock on error in get_srq_wqe()
RDMA/cma: Fix rdma_resolve_route() memory leak
RDMA/core/sa_query: Remove unused argument
RDMA/cma: Fix incorrect Packet Lifetime calculation
RDMA/cma: Protect RMW with qp_mutex
RDMA/cma: Remove unnecessary INIT->INIT transition
RDMA/hns: Add window selection field of congestion control
RDMA/hfi1: Remove use of kmap()
RDMA/irdma: Remove use of kmap()
RDMA/bnxt_re: Fix uninitialized struct bit field rsvd1
IB/isert: Align target max I/O size to initiator size
RDMA/hns: Fix incorrect vlan enable bit in QPC
MAINTAINERS: Update Broadcom RDMA maintainers
RDMA/irdma: Use the queried port attributes
RDMA/rxe: Fix redundant skb_put_zero
RDMA/rxe: Fix extra copy in prepare_ack_packet
...
Assignment to *ring should be done after correctness check of the
argument queue.
Fixes: 91db364236 ("igb: Refactor igb_configure_cbs()")
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Fixes: 047e0030f1 ("igb: add new data structure for handling interrupts and NAPI")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 111b9dc5c9 ("e1000e: add aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb9 ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72 ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: c9a11c23ce ("igc: Add netdev")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 6fabd715e6 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Static analysis reports this problem
igc_main.c:4944:20: warning: The left operand of '&'
is a garbage value
if (!(phy_data & SR_1000T_REMOTE_RX_STATUS) &&
~~~~~~~~ ^
phy_data is set by the call to igc_read_phy_reg() only if
there is a read_reg() op, else it is unset and a 0 is
returned. Change the return to -EOPNOTSUPP.
Fixes: 208983f099 ("igc: Add watchdog")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If this 'kzalloc()' fails we must free some resources as in all the other
error handling paths of this function.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_get_vf_vsi() is being called twice for the same VSI. Remove the
unnecessary call/assignment.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Remove the VSI info from previous aggregator after moving the VSI to a
new aggregator.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.
Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.
This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is modeled after one by Scott Peterson for i40e.
Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.
Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.
Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Complete to commit def4ec6dce ("e1000e: PCIm function state support")
Check the PCIm state only on CSME systems. There is no point to do this
check on non CSME systems.
This patch fixes a generation a false-positive warning:
"Error in exiting dmoff"
Fixes: def4ec6dce ("e1000e: PCIm function state support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change that made i40e use new udp_tunnel infrastructure
uses a method that expects to be called under rtnl lock.
However, not all codepaths do the lock prior to calling
i40e_setup_pf_switch.
Fix that by adding additional rtnl locking and unlocking.
Fixes: 40a98cb6f0 ("i40e: convert to new udp_tunnel infrastructure")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As reported by Alex Sergeev, the i40e driver is incrementing the PTP
clock at 40Gb speeds when linked at 5Gb. Fix this bug by making
sure that the right multiplier is selected when linked at 5Gb.
Fixes: 3dbdd6c2f7 ("i40e: Add support for 5Gbps cards")
Cc: stable@vger.kernel.org
Reported-by: Alex Sergeev <asergeev@carbonrobotics.com>
Suggested-by: Alex Sergeev <asergeev@carbonrobotics.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel drivers all have rcu_read_lock()/rcu_read_unlock() pairs around
XDP program invocations. However, the actual lifetime of the objects
referred by the XDP program invocation is longer, all the way through to
the call to xdp_do_flush(), making the scope of the rcu_read_lock() too
small. This turns out to be harmless because it all happens in a single
NAPI poll cycle (and thus under local_bh_disable()), but it makes the
rcu_read_lock() misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> # i40e
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-12-toke@redhat.com
Disabling autonegotiation was allowed only for 10GBaseT PHY.
The condition was changed to check if link media type is BaseT.
Fixes: 3ce12ee9d8 ("i40e: Fix order of checks when enabling/disabling autoneg in ethtool")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Karen Sornek <karen.sornek@intel.com>
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When vsi->type == I40E_VSI_FDIR, we have caught the return value of
i40e_vsi_request_irq() but without further handling. Check and execute
memory clean on failure just like the other i40e_vsi_request_irq().
Fixes: 8a9eb7d3cb ("i40e: rework fdir setup and teardown")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDPuyMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvxgH/RKvSuRPwkJ2Jcp9
VLi5kCbqtJlYLq6tB6peSJ8otKgxkcRwC0pIY4LlYIAWYboktLQ5RKp/9nB2h2FN
aMZUMu6AI/lVJyFMI5MnKnJIUiUq+WXR3lSSlw68vwFLFdzqUZFNq+bqeiVvnIy1
yqA6naj24Tu/RbYffQoPvdSJcU2SLXRMxwD8HRGiU2d51RaFsOvsZvF+P5TVcsEV
ZmttJeER21CaI/A809eqaFmyGrUOcZZK9roZEbMwanTZOMw18biEsLu/UH4kBX01
JC4+RlGxcWjQ5YNZgChsgoOK/CHzc6ITztTntdeDWAvwZjQFzV7pCy4/3BWne3O+
5178yHM=
=o8cN
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc7' into rdma.git for-next
Linux 5.13-rc7
Needed for dependencies in following patches. Merge conflict in rxe_cmop.c
resolved by compining both patches.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the unused ptype struct value, which makes table init easier for
the zero entries, and use ranged initializer to remove a bunch of code
(works with gcc and clang). There is no significant functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the unused ptype struct value, which makes table init easier for
the zero entries, and use ranged initializer to remove a bunch of code
(works with gcc and clang). There is no significant functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The hardware is reporting the type of the hash used for RSS
as a PTYPE field in the receive descriptor. Use this value to set
the skb packet hash type by extending the hash type table to
cover all 10-bits of possible values (requiring some variables
to be changed from u8 to u16), and then use that table to convert
to one of the possible values in enum pkt_hash_types.
While we're here, remove the unused ptype struct value, which
makes table init easier for the zero entries, and use ranged
initializer to remove a bunch of code (works with gcc and clang).
Without this change, the kernel will recalculate the hash in software,
which can consume extra CPU cycles.
Co-developed-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The continue statement in the for-loop is redundant. Re-work the hw_lock
check to remove it.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following compilation warning if PTP_1588_CLOCK is not enabled
drivers/net/ethernet/intel/ice/ice_ptp.h:149:1:
error: return type defaults to ‘int’ [-Werror=return-type]
ice_ptp_request_ts(struct ice_ptp_tx *tx, struct sk_buff *skb)
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ptp_read_system_prets and ptp_read_system_postts functions already
check for the NULL value of the ptp_system_timestamp structure pointer.
There is no need to check this manually in the ice driver code. Remove
the checks.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Function 'ice_is_vsi_valid' is declared twice, remove the
repeated declaration.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the local variable since it's only used once. Instead, use it
directly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are some places where the scope of a variable can
be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The entry for PTYPE 2 in the ice_ptype_lkup table incorrectly states
that this is an L2 packet with no payload. According to the datasheet,
this PTYPE is actually unused and reserved.
Fix the lookup entry to indicate this is an unused entry that is
reserved.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The entry for PTYPE 90 indicates that the payload is layer 3. This does
not match the specification in the datasheet which indicates the packet
is a MAC, IPv6, UDP packet, with a payload in layer 4.
Fix the lookup table to match the data sheet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.
The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.
Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.
To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.
In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.
For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.
Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.
This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.
It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.
Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.
Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.
With this change, E810 devices should be able to perform basic PTP
functionality.
Future changes will extend the support to cover the E822-based devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.
Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.
The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.
If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is
PHC - (lower_32_bits(PHC) - timestamp)
If the Rx timestamp was captured after the PHC time, then the real
timestamp is
PHC + (timestamp - lower_32_bits(PHC))
These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.
In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.
Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.
Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.
To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.
Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.
With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that the driver registers a PTP clock device that represents the
clock hardware, it is important that the clock index is reported via the
ethtool .get_ts_info callback.
The underlying hardware resource is shared between multiple PF
functions. Only one function owns the hardware resources associated with
a timer, but multiple functions may be associated with it for the
purposes of timestamping.
To support this, the owning PF will store the clock index into the
driver shared parameters buffer in firmware. Other PFs will look up the
clock index by reading the driver shared parameter on demand when
requested via the .get_ts_info ethtool function.
In this way, all functions which are tied to the same timer are able to
report the clock index. Userspace software such as ptp4l performs
a look up on the netdev to determine the associated clock, and all
commands to control or configure the clock will be handled through the
controlling PF.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.
For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.
Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.
The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit ae15e0ba1b ("ice: Change number of XDP Tx queues to match
number of Rx queues") tried to address the incorrect setting of XDP
queue count that was based on the Tx queue count, whereas in theory we
should provide the XDP queue per Rx queue. However, the routines that
setup and destroy the set of Tx resources are still based on the
vsi->num_txq.
Ice supports the asynchronous Tx/Rx queue count, so for a setup where
vsi->num_txq > vsi->num_rxq, ice_vsi_stop_tx_rings and ice_vsi_cfg_txqs
will be accessing the vsi->xdp_rings out of the bounds.
Parameterize two mentioned functions so they get the size of Tx resources
array as the input.
Fixes: ae15e0ba1b ("ice: Change number of XDP Tx queues to match number of Rx queues")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-06-07
This series contains updates to virtchnl header file and ice driver.
Brett adds capability bits to virtchnl to specify whether a primary or
secondary MAC address is being requested and adds the implementation to
ice. He also adds storing of VF MAC address so that it will be preserved
across reboots of VM and refactors VF queue configuration to remove the
expectation that configuration be done all at once.
Krzysztof refactors ice_setup_rx_ctx() to remove configuration not
related to Rx context into a new function, ice_vsi_cfg_rxq().
Liwei Song extends the wait time for the global config timeout.
Salil Mehta refactors code in ice_vsi_set_num_qs() to remove an
unnecessary call when the user has requested specific number of Rx or Tx
queues.
Jesse converts define macros to static inlines for NOP configurations.
Jake adds messaging when devlink fails to read device capabilities and
when pldmfw cannot find the requested firmware. Adds a wait for reset
completion when reporting devlink info and reinitializes NVM during
rebuild to ensure values are current.
Ani adds detection and reporting of modules exceeding supported power
levels and changes an error message to a debug message.
Paul fixes a clang warning for deadcode.DeadStores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clang generates deadcode.DeadStores warnings when a variable
is used to read a value, but then that value isn't used later
in the code. Fix this warning.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Failing to add or remove LLDP filter doesn't seem to be a fatal
error, so downgrade the dev_err message to a dev_dbg message.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When flashing a new firmware image onto the device, the pldmfw library
parses the image contents looking for a matching record. If no record
can be found, the function reports an error of -ENOENT. This can produce
a very confusing error message and experience for the user:
$devlink dev flash pci/0000🆎00.0 file image.bin
devlink answers: No such file or directory
This is because the ENOENT error code is interpreted as a missing file
or directory. The pldmfw library does not have direct access to the
extack pointer as it is generic and non-netdevice specific. The only way
that ENOENT is returned by the pldmfw library is when no record matches.
Catch this specific error and report a suitable extended ack message:
$devlink dev flash pci/0000🆎00.0 file image.bin
Error: ice: Firmware image has no record matching this device
devlink answers: No such file or directory
In addition, ensure that we log an error message to the console whenever
this function fails. Because our driver specific PLDM operation
functions potentially set the extended ACK message, avoid overwriting
this with a generic message.
This change should result in an improved experience when attempting to
flash an image that does not have a compatible record.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When filling out information for the DEVLINK_CMD_INFO_GET, the driver
needs to read some device capabilities. Add an extack message to
properly inform the caller of the failure, as we do for other failures
in this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial:
The driver had previously attempted to use #define
macros to make functions that have no use in certain
configs disappear. Using static inlines instead allows
for certain static checkers to process the code better,
and results in no functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If user has explicitly requested the number of {R,T}XQs, then it is
unnecessary to get the count of already available {R,T}XQs from the
PF avail_{r,t}xqs bitmap. This value will get overridden by user specified
value in any case.
Re-organize this code for improving the flow, readability and efficiency.
This scope of improvement was found during the review of the ICE driver
code.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Cc: intel-wired-lan@lists.osuosl.org
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It may need hold Global Config Lock a longer time when download DDP
package file, extend the timeout value to 5000ms to ensure that
download can be finished before other AQ command got time to run,
this will fix the issue below when probe the device, 5000ms is a test
value that work with both Backplane and BreakoutCable NVM image:
ice 0000:f4:00.0: VSI 12 failed lan queue config, error ICE_ERR_CFG
ice 0000:f4:00.0: Failed to delete VSI 12 in FW - error: ICE_ERR_AQ_TIMEOUT
ice 0000:f4:00.0: probe failed due to setup PF switch: -12
ice: probe of 0000:f4:00.0 failed with error -12
Signed-off-by: Liwei Song <liwei.song@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when a VF requests queue configuration via
VIRTCHNL_OP_CONFIG_VSI_QUEUES the PF driver expects that this message
will only be called once and we always assume the queues being
configured start from 0. This is incorrect and is causing issues when
a VF tries to send this message for multiple queue blocks. Fix this by
using the queue_id specified in the virtchnl message and allowing for
individual Rx and/or Tx queues to be configured.
Also, reduce the duplicated for loops for configuring the queues by
moving all the logic into a single for loop.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move AF_XDP logic and buffer allocation out of ice_setup_rx_ctx() to a
new function ice_vsi_cfg_rxq(), so the function actually sets up the Rx
context.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
If a VM reboots and/or VF driver is unloaded, its cached hardware MAC
address (hw_lan_addr.addr) is cleared in some cases. If the VF is
trusted, then the PF driver allows the VF to clear its old MAC address
even if this MAC was configured by a host administrator. If the VF is
untrusted, then the PF driver allows the VF to clear its old MAC
address only if the host admin did not set it.
For the trusted VF case, this is unexpected and will cause issues
because the host configured MAC (i.e. via XML) will be cleared on VM
reboot. For the untrusted VF case, this is done to be consistent and it
will allow the VF to keep the same MAC across VM reboot.
Fix this by introducing dev_lan_addr to the VF structure. This will be
the VF's MAC address when it's up and running and in most cases will be
the same as the hw_lan_addr. However, to address the VM reboot and
unload/reload problem, the driver will never allow the hw_lan_addr to be
cleared via VIRTCHNL_OP_DEL_ETH_ADDR. When the VF's MAC is changed, the
dev_lan_addr and hw_lan_addr will always be updated with the same value.
The only ways the VF's MAC can change are the following:
- Set the VF's MAC administratively on the host via iproute2.
- If the VF is trusted and changes/sets its own MAC.
- If the VF is untrusted and the host has not set the MAC via iproute2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently there is no way for a VF driver to specify if it wants to
change it's hardware address. New bits are being added to virtchnl.h
in struct virtchnl_ether_addr that allow for the VF to correctly
communicate this information. However, legacy VF drivers that don't
support the new virtchnl.h bits still need to be supported. Make a
best effort attempt at saving the VF's primary/device address in the
legacy case and depend on the VIRTCHNL_ETHER_ADDR_PRIMARY type for
the new case.
Legacy case - If a unicast MAC is being added and the
hw_lan_addr.addr is empty, then populate it. This assumes that the
address is the VF's hardware address. If a unicast MAC is being
added and the hw_lan_addr.addr is not empty, then cache it in the
legacy_last_added_umac.addr. If a unicast MAC is being deleted and it
matches the hw_lan_addr.addr, then zero the hw_lan_addr.addr.
Also, if the legacy_last_added_umac.addr has not expired, copy the
legacy_last_added_umac.addr into the hw_lan_addr.addr. This is done
because we cannot guarantee the order of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR.
New case - If a unicast MAC is being added and it's specified as
VIRTCHNL_ETHER_ADDR_PRIMARY, then replace the current
hw_lan_addr.addr. If a unicast MAC is being deleted and it's type
is specified as VIRTCHNL_ETHER_ADDR_PRIMARY, then zero the
hw_lan_addr.addr.
Untrusted VFs - Only allow above legacy/new changes to their
hardware address if the PF has not set it administratively via
iproute2.
Trusted VFs - Always allow above legacy/new changes to their
hardware address even if the PF has administratively set it via
iproute2.
Also, change the variable dflt_lan_addr to hw_lan_addr to clearly
represent the purpose of this variable since it's purpose is to
act as a hardware programmed MAC address for the VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add HW VLAN acceleration protocol handling. In case of HW VLAN tagging,
we need that protocol available in the ndo_start_xmit(), so that it will be
stored in a new fields in the skb.
HW offloading is set to OFF by default.
Users are allow to turn on/off Rx/Tx HW VLAN acceleration via ethtool.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Minor fix of indentation in igc_defines.h
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The MDICNFG register from igc registers is not used so remove it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The CR_1000T_ASYM_PAUSE bit from igc defines is not used so remove it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Complete to commit c8d4725e98 ("intel: Update drivers to use
ethtool_sprintf")
Update the igc driver to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Suggested-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.
SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.
Then ethernet header has to have to correct value for
the protocol though.
Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).
Fixes: 0c3a6101ff ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ethtool incorrectly reported supported and advertised auto-negotiation
settings for a backplane PHY image which did not support auto-negotiation.
This can occur when using media or PHY type for reporting ethtool
supported and advertised auto-negotiation settings.
Remove setting supported and advertised auto-negotiation settings based
on PHY type in ice_phy_type_to_ethtool(), and MAC type in
ice_get_link_ksettings().
Ethtool supported and advertised auto-negotiation settings should be
based on the PHY image using the AQ command get PHY capabilities with
media. Add setting supported and advertised auto-negotiation settings
based get PHY capabilities with media in ice_get_link_ksettings().
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VSI rebuild can be failed for LAN queue config, then the VF's VSI will
be NULL, the VF reset should be stopped with the VF entering into the
disable state.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282c ("ice: clear VF ARQLEN register on reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12bb018c53 ("ice: Refactor VF reset") caused a regression
that removes the ability for a VF to request a different amount of
queues via VIRTCHNL_OP_REQUEST_QUEUES. This prevents VF drivers to
either increase or decrease the number of queue pairs they are
allocated. Fix this by using the variable vf->num_req_qs when
determining the vf->num_vf_qs during VF VSI creation.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
silently introduced a regression and broke the Tx side of AF_XDP in copy
mode. xsk_pool on ice_ring is set only based on the existence of the XDP
prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed.
That is not something that should happen for copy mode as it should use
the regular data path ice_clean_tx_irq.
This results in a following splat when xdpsock is run in txonly or l2fwd
scenarios in copy mode:
<snip>
[ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 106.057269] #PF: supervisor read access in kernel mode
[ 106.062493] #PF: error_code(0x0000) - not-present page
[ 106.067709] PGD 0 P4D 0
[ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45
[ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50
[ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00
[ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206
[ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800
[ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800
[ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800
[ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff
[ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018
[ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000
[ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0
[ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.192898] PKRU: 55555554
[ 106.195653] Call Trace:
[ 106.198143] <IRQ>
[ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice]
[ 106.205087] ice_napi_poll+0x3e/0x590 [ice]
[ 106.209356] __napi_poll+0x2a/0x160
[ 106.212911] net_rx_action+0xd6/0x200
[ 106.216634] __do_softirq+0xbf/0x29b
[ 106.220274] irq_exit_rcu+0x88/0xc0
[ 106.223819] common_interrupt+0x7b/0xa0
[ 106.227719] </IRQ>
[ 106.229857] asm_common_interrupt+0x1e/0x40
</snip>
Fix this by introducing the bitmap of queues that are zero-copy enabled,
where each bit, corresponding to a queue id that xsk pool is being
configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and
checked within ice_xsk_pool(). The latter is a function used for
deciding which napi poll routine is executed.
Idea is being taken from our other drivers such as i40e and ixgbe.
Fixes: c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 73f1071c1d ("igc: Add support for XDP_TX action")
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different errors
can occur. The support was only partial. Several errors where not
logged which would confuse the user quite a lot not knowing where and
why the packets disappeared.
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When using native XDP with the igb driver, the XDP frame data doesn't point to
the beginning of the packet. It's off by 16 bytes. Everything works as expected
with XDP skb mode.
Actually these 16 bytes are used to store the packet timestamps. Therefore, pull
the timestamp before executing any XDP operations and adjust all other code
accordingly. The igc driver does it like that as well.
Tested with Intel i210 card and AF_XDP sockets.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Kconfig and Makefile to build irdma driver.
Remove i40iw driver and add an alias in irdma.
Remove legacy exported symbols i40e_register_client
and i40e_unregister_client from i40e as they are no
longer used.
irdma is the replacement driver that supports X722.
Link: https://lore.kernel.org/r/20210602205138.889-16-shiraz.saleem@intel.com
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Tony Nguyen says:
====================
iwl-next Intel Wired LAN Driver Updates 2021-06-01
This pull request is targeting net-next and rdma-next branches.
These patches have been reviewed by netdev and rdma mailing lists[1].
This series adds RDMA support to the ice driver for E810 devices and
converts the i40e driver to use the auxiliary bus infrastructure
for X722 devices. The PCI netdev drivers register auxiliary RDMA devices
that will bind to auxiliary drivers registered by the new irdma module.
[1] https://lore.kernel.org/netdev/20210520143809.819-1-shiraz.saleem@intel.com/
---
v3:
- ice_aq_add_rdma_qsets(), ice_cfg_vsi_rdma(), ice_[ena|dis]_vsi_rdma_qset(),
and ice_cfg_rdma_fltr() no longer return ice_status
- Remove null check from ice_aq_add_rdma_qsets()
v2:
- Added patch 'i40e: Replace one-element array with flexible-array
member'
Changes since linked review (v6):
- Removed unnecessary checks in i40e_client_device_register() and
i40e_client_device_unregister()
- Simplified the i40e_client_device_register() API
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_IGB_HWMON is n, gcc warns:
drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17:
warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_therm_limit[4] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17:
warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_temp_data[4] = {
^~~~~~~~~~~~~~~~~~~
Move it into #ifdef block to fix this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert i40e to use the auxiliary bus infrastructure to export
the RDMA functionality of the device to the RDMA driver.
Register i40e client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the new auxiliary rdma driver (irdma) to
attach to.
The global i40e_register_client and i40e_unregister_client symbols
will be obsoleted once irdma replaces i40iw in the kernel
for the X722 device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace union with a couple of pointers in order to fix the following
out-of-bounds warning:
CC [M] drivers/net/ethernet/intel/ixgbe/ixgbe_common.o
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c: In function ‘ixgbe_host_interface_command’:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3729:13: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
3729 | bp->u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
| ~~~~~~~~~~^~~~
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3682:7: note: while referencing ‘u32arr’
3682 | u32 u32arr[1];
| ^~~~~~
This helps with the ongoing efforts to globally enable -Warray-bounds.
Link: https://github.com/KSPP/linux/issues/109
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210527173424.362456-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in struct
i40e_qvlist_info instead of one-element array, and use the struct_size()
helper.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the sparse warnings in the ixgbe crypto offload code. These
changes were made in the most conservative way (force cast)
in order to hopefully not break the code. I suspect that the
code might still be broken on big-endian architectures, but
no one is complaining, so I'm just leaving it functionally
the same.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <snelson@pensando.io>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe hardware needs some very specific programming for
certain registers, which led to some misguided usage of ntohs
instead of using be16_to_cpu(), as well as a home grown swap
followed by an ntohs. Sparse didn't like this at all, and this
fixes the C=2 build, with code that uses native kernel interface.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igbvf driver for some reason never strongly typed it's descriptor
formats. Make this driver like the rest of the Intel drivers and use
__le* for our little endian descriptors.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) found that there were two drivers
who had not been convered to call the csum_replace_by_diff() function
with sparse clean arguments. Most if not all drivers force the cast
like this patch does. So these drivers are now joining the party
(a bit late), but with no functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb PTP code was using htons() on a constant to try to
byte swap the value before writing it to a register. This byte
swap has the consequence of triggering sparse conflicts between
the register write which expect cpu ordered input, and the code
which generated a big endian constant. Just override the cast
to make sure code doesn't change but silence the warning.
Can't do a __swab16 in this case because big endian systems
would then write the wrong value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb driver was trying hard to be sparse correct, but somehow
ended up converting a variable into little endian order and then
tries to OR something with it.
A much plainer way of doing things is to leave all variables and
OR operations in CPU (non-endian) mode, and then convert to
little endian only once, which is what this change does.
This probably fixes a bug that might have been seen only on
big endian systems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) finds some issues with how the driver
dealt with the (very difficult) hardware that in some generations
uses little-endian, and in others uses big endian, for the VLAN
field. The code as written picks __le16 as a type and for some
hardware revisions we override it to __be16 as done in this
patch. This impacted the VF driver as well so fix it there too.
Also change the vlan_tci assignment to override the sparse
warning without changing functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb and igc driver both use a trick of creating a local type
pointer on the stack to ease dealing with a receive descriptor in
64 bit chunks for printing. Sparse however was not taken into
account and receive descriptors are always in little endian
order, so just make the unions use __le64 instead of u64.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The error check and set_bit are placed in such a way that sparse (C=2)
warns:
.../fm10k_pci.c:1395:9: warning: context imbalance in 'fm10k_msix_mbx_pf' - different lock contexts for basic block
Which seems a little odd, but the code can obviously be moved
to where the variable is being set without changing functionality
at all, and it even seems to make a bit more sense with the check
closer to the set.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse checker (C=2) found an assignment where we were mixing
types when trying to convert from data read directly from the
device NVM, to an array in CPU order in-memory, which
unfortunately the driver tries to do in-place.
This is easily solved by using the swap operation instead of an
assignment, and is already proven in other Intel drivers to be
functionally correct and the same code, just without a sparse
warning.
The change is the same in all three drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sparse tool was warning on some implicit conversions from
little endian data read from the EEPROM on the e100 cards.
Fix these by being explicit about the conversions using
le16_to_cpu().
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9 ("ixgbe: Enable jumbo frames support w/ SR-IOV")
Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmitting packets via AF_XDP zero-copy mechanism.
The packet transmission itself is implemented by igc_xdp_xmit_zc() which
is called from igc_clean_tx_irq() when the ring has AF_XDP zero-copy
enabled. Likewise i40e and ice drivers, the transmission budget used is
the number of descriptors available on the ring.
A new tx buffer type is introduced to 'enum igc_tx_buffer_type' to
indicate the tx buffer uses memory from xsk pool so it can be properly
cleaned after transmission or when the ring is cleaned.
The I225 controller has only 4 Tx hardware queues so the main difference
between igc and other Intel drivers that support AF_XDP zero-copy is
that there is no tx ring dedicated exclusively to XDP. Instead, tx
rings are shared between the network stack and XDP, and netdev queue
lock is used to ensure mutual exclusion. This is the same approach
implemented to support XDP_TX and XDP_REDIRECT actions.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for receiving packets via AF_XDP zero-copy mechanism.
Add a new flag to 'enum igc_ring_flags_t' to indicate the ring has
AF_XDP zero-copy enabled so proper ring setup is carried out during ring
configuration in igc_configure_rx_ring().
RX buffers can now be allocated via the shared pages mechanism (default
behavior of the driver) or via xsk pool (when AF_XDP zero-copy is
enabled) so a union is added to the 'struct igc_rx_buffer' to cover both
cases.
When AF_XDP zero-copy is enabled, rx buffers are allocated from the xsk
pool using the new helper igc_alloc_rx_buffers_zc() which is the
counterpart of igc_alloc_rx_buffers().
Likewise other Intel drivers that support AF_XDP zero-copy, in igc we
have a dedicated path for cleaning up rx irqs when zero-copy is enabled.
This avoids adding too many checks within igc_clean_rx_irq(), resulting
in a more readable and efficient code since this function is called from
the hot-path of the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Up to this point, Tx buffers are associated with either a skb or a xdpf,
and the IGC_TX_FLAGS_XDP flag was enough to distinguish between these
two case. However, with upcoming patches that will add AF_XDP zero-copy
support, a third case will be introduced so this flag-based approach
won't fit well.
In preparation to land AF_XDP zero-copy support, replace the
IGC_TX_FLAGS_XDP flag by an enum which will be extended once zero-copy
support is introduced to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
unmaps Tx buffers into its own local helper so we can reuse it, avoiding
code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
updates the driver RX stats in its own local helper so it can be reused
in the zero-copy path. Likewise, encapsulate TX stats code as well.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor XDP rxq info registration code, preparing the driver for AF_XDP
zero-copy support which is added by upcoming patches.
Currently, xdp_rxq and memory model are both registered during RX
resource setup time by igc_xdp_register_rxq_info() helper. With AF_XDP,
we want to register the memory model later on while configuring the ring
because we will know which memory model type to register
(MEM_TYPE_PAGE_SHARED or MEM_TYPE_XSK_BUFF_POOL).
The helpers igc_xdp_register_rxq_info() and igc_xdp_unregister_rxq_
info() are not useful anymore so they are removed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc_clean_rx_ring() helper, preparing the code for AF_XDP
zero-copy support which is added by upcoming patches.
The refactor consists of encapsulating page-shared specific code into
its own helper, leaving common code that will be shared by both
page-shared and xsk pool in igc_clean_rx_ring().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor __igc_xdp_run_prog() helper from igc_xdp_run_prog(),
preparing the code for AF_XDP zero-copy support which is added
by upcoming patches.
The existing igc_xdp_run_prog() caters to regular XDP rx path
which has to verify if bpf_prog is not NULL. Zero-copy
path assumes that bpf_prog is not NULL and hence this check is
not required. Therefore it makes sense to refactor the common
code into a helper function, to avoid code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move the helper igc_xdp_is_enabled() to igc_xdp.h so it can be reused in
igc_xdp.c by upcoming patches that will introduce AF_XDP zero-copy
support to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a misspell word "retreived" in comment, so fix it to "retrieved".
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "slot" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "the" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "in" and "to" in comments, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "slot" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the xdp_{init,prepare}_buff() helpers instead of
an open-coded version.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0a ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the FDIR entry is found, just return the result directly to break
the loop.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The maximum number (2) of flex-byte support is derived from ethtool
use-def data size (8 byte).
Change the magic number 2 to macro definition, and add the comment to
track the design thinking, so the code is clear and easily maintained.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both iavf_free_all_tx_resources() and iavf_free_all_rx_resources() have
already been called in the very same function.
Remove the duplicate calls.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The minimum size of admin send/receive queue is 1 and 2 respectively.
The admin send queue can't be set to 1 because in that case, the
firmware would fail to init.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the minimum of the number of descriptors thus we will allocate the
minimal ring buffers for kdump.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Set the number of the MSI-X vectors to 1. When MSI-X is enabled,
it's not allowed to use more TC queue pairs than MSI-X vectors
(pf->num_lan_msix) exist. Thus the number of Tx and Rx pairs
(vsi->num_queue_pairs) will be equal to the number of MSI-X vectors,
i.e., 1.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor repeated link state reporting code into a separate helper
functions: i40e_set_vf_link_state() i40e_vc_link_speed2mbps().
Add support of VIRTCHNL_VF_CAP_ADV_LINK_SPEED;
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provide the ability to enable SCTP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the SCTP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable UDP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the UDP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Provides the ability to enable TCP RSS hashing by ethtool.
It gives users option of generating RSS hash based on the TCP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the virtchnl message interface to VF, so that VF can request RSS
input set(s) based on PF's capability.
This framework allows ethtool RSS config support on the VF driver.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, RSS hash input is not available to AVF by ethtool, it is set
by the PF directly.
Add the RSS configure support for AVF through new virtchnl message, and
define the capability flag VIRTCHNL_VF_OFFLOAD_ADV_RSS_PF to query this
new RSS offload support.
Signed-off-by: Jia Guo <jia.guo@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Bo Chen <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the driver gets the VF's VSI by using a long string of
dereferences (i.e. vf->pf->vsi[vf->lan_vsi_idx]). If the method to get
the VF's VSI were to change the driver would have to change it in every
location. Fix this by adding the helper ice_get_vf_vsi().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pointer vsi is being re-assigned a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add code to support UDP segmentation offload (USO) for
hardware that supports it.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As the hardware is capable of supporting UDP segmentation offload, add a
capability bit to virtchnl.h to communicate this and have the driver
advertise its support.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Declare bitmap of allowed commands on VF. Initialize default
opcodes list that should be always supported. Declare array of
supported opcodes for each caps used in virtchnl code.
Change allowed bitmap by setting or clearing corresponding
bit to allowlist (bit set) or denylist (bit clear).
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose EEE Tx and Rx low power idle counters via ethtool
A EEE TX or RX LPI event occurs when the transmitter or the receiver
enters EEE (IEEE802.3az) LPI state.
ethtool --statistics <iface>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs) - much like i210, which is used as
inspiration for this patch. It enables two possible functions, namely
time stamping external events and periodic output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
For the external events time stamping, when the SDP (configured as input
by user) level changes, an interrupt is generated and the kernel
Precision Time Protocol (PTP) is informed.
For the periodic output signals, the i225 is configured to generate them
(so the SDP level will change periodically) and the driver also has to
keep updating the time of the next level change. However, this work is
not necessary for some frequencies as the i225 takes care of them
(namely, anything with a half-cycle of 500ms, 250ms, 125ms or < 70ms).
While i225 allows up to four timers to be used to source the time used
on the external events or output signals, this patch uses only one of
those timers. Main reason is to keep it simple, as it's not clear how
these extra timers would be exposed to users. Note that currently a NIC
can expose a single PTP device.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device can produce one interrupt on the full second, much
like i210 - from where this patch is inspired.
This patch sets up the full second interruption on the i225 and when
receiving it, it sends a PPS event to PTP (Precision Time Protocol)
kernel subsystem.
The PTP subsystem exposes the PPS events via ioctl and sysfs, and one
can use the `testptp` tool (tools/testing/selftests/ptp) to check that
the events are being generated.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new function which checks MTA_REGISTER if its filled correctly.
If not then writes again to same register.
There is possibility that i210 and i211 could not accept
MTA_REGISTER settings, specially when you add and remove
many of multicast addresses in short time.
Without this patch there is possibility that multicast settings will be
not always set correctly in hardware.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i210 has a total of 24KB of transmit packet buffer. When in Qav mode,
this buffer is divided into four pieces, one for each Tx queue.
Currently, 8KB are given to each of the two SR queues and 4KB are given
to each of the two SP queues.
However, it was noticed that such distribution can make best effort
traffic (which would usually go to the SP queues when Qav is enabled, as
the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic)
perform poorly. Using iperf3 to measure, one could see the performance
of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps),
with no TSN traffic competing.
This patch redistributes the 24KB to each queue equally: 6KB each. On
tests, there was no notable performance reduction of best effort traffic
performance when there was no TSN traffic competing.
Below, more details about the data collected:
All experiments were run using the following qdisc setup:
qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3
queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1
clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0
index 0 cmd S gatemask 0xf interval 10000000
qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on
deadline_mode off skip_sock_check off
TSN traffic, when enabled, had this characteristics:
Packet size: 1500 bytes
Transmission interval: 125us
----------------------------------
Without this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%)
----------------------------------
With this patch:
----------------------------------
- TCP data:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1
- TCP data limiting iperf3 buffer size to 4K:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- TCP data limiting iperf3 buffer size to 192 bytes (smallest size without
serious performance degradation):
- No TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1
- With TSN traffic:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0
- UDP data at 1000Mbit/sec:
- No TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%)
- With TSN traffic:
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%)
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
RIP: 0010:i40e_xdp+0xdd/0x1b0 [i40e]
Call Trace:
[2160294.717292] ? i40e_reconfig_rss_queues+0x170/0x170 [i40e]
[2160294.717666] dev_xdp_install+0x4f/0x70
[2160294.718036] dev_change_xdp_fd+0x11f/0x230
[2160294.718380] ? dev_disable_lro+0xe0/0xe0
[2160294.718705] do_setlink+0xac7/0xe70
[2160294.719035] ? __nla_parse+0xed/0x120
[2160294.719365] rtnl_newlink+0x73b/0x860
Fixes: 41c445ff0f ("i40e: main driver core")
Co-developed-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Shujin Li <lishujin@kuaishou.com>
Signed-off-by: Jason Xing <xingwanli@kuaishou.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scope of this variable can be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF. Mostly this struct member was unused.
Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.
Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.
Basically unpack the "high bit means dynamic" logic
into bitfields.
Also, remove some unused ITR defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.
Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.
This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them. This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.
In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files. Use those definitions instead of open-coding the
same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the 'ixgbe_mc_addr_itr' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Broadcom PHY is used in switches, so add the ID, and hook it up.
This upstreams the Linux kernel patch from the network operating system
SONiC from February 2020 [1].
[1]: https://github.com/Azure/sonic-linux-kernel/pull/122
Signed-off-by: Jostar Yang <jostar_yang@accton.com>
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A for-loop is using a u8 loop counter that is being compared to
a u32 cmp_dcbcfg->numapp to check for the end of the loop. If
cmp_dcbcfg->numapp is larger than 255 then the counter j will wrap
around to zero and hence an infinite loop occurs. Fix this by making
counter j the same type as cmp_dcbcfg->numapp.
Addresses-Coverity: ("Infinite loop")
Fixes: aeac8ce864 ("ice: Recognize 860 as iSCSI port in CEE mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b25587 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.
Fix the following call trace.
ixgbe 0000:17:00.1: disabling already-disabled device
Call Trace:
__ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
ixgbe_suspend+0x32/0x70 [ixgbe]
pci_pm_suspend+0x87/0x160
? pci_pm_freeze+0xd0/0xd0
dpm_run_callback+0x42/0x170
__device_suspend+0x114/0x460
async_suspend+0x1f/0xa0
async_run_entry_fn+0x3c/0xf0
process_one_work+0x1dd/0x410
worker_thread+0x34/0x3f0
? cancel_delayed_work+0x90/0x90
kthread+0x14c/0x170
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x30
Fixes: 6f82b25587 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe driver currently generates a NULL pointer dereference when
performing the ethtool loopback test. This is due to the fact that there
isn't a q_vector associated with the test ring when it is setup as
interrupts are not normally added to the test rings.
To address this I have added code that will check for a q_vector before
returning a napi_id value. If a q_vector is not present it will return a
value of 0.
Fixes: b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20 ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Init pointer with NULL in default switch case statement.
Previously the error was produced when compiling against sparse.
i40e_debugfs.c:582 i40e_dbg_dump_desc() error: uninitialized symbol 'ring'.
Fixes: 44ea803e2f ("i40e: introduce new dump desc XDP command")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove error handling through pointers. Instead use plain int
to return value from i40e_run_xdp(...).
Previously:
- sparse errors were produced during compilation:
i40e_txrx.c:2338 i40e_run_xdp() error: (-2147483647) too low for ERR_PTR
i40e_txrx.c:2558 i40e_clean_rx_irq() error: 'skb' dereferencing possible ERR_PTR()
- sk_buff* was used to return value, but it has never had valid
pointer to sk_buff. Returned value was always int handled as
a pointer.
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Fixes: 2e68931238 ("i40e: split XDP_TX tail and XDP_REDIRECT map flushing")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change parameters order in aq_get_phy_register() due to wrong
statistics in PHY reported by ethtool. Previously all PHY statistics were
exactly the same for all interfaces
Now statistics are reported correctly - different for different interfaces
Fixes: 0514db37dd ("i40e: Extend PHY access with page change flag")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Beyond a specific version of firmware, there is no need to provide
override values to the firmware when setting PHY capabilities. In this
case, we do not need to indicate whether we're in Strict or Lenient Link
Mode.
In the case of translating capabilities to the configuration structure,
the module compliance enforcement is already correctly set by firmware,
so the extra code block is redundant.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, use assignment instead of memset/memcpy
where possible
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return more appropriate error codes so that the right error
message is communicated to the user by ethtool.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_link_ksettings, change 'abilities' to 'phy_caps' and 'p' to
'pi'. This is more consistent with similar usages elsewhere in the
driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The loop checking for PF VSI doesn't make any sense. The VSI type
backing the netdev passed to ice_set_link_ksettings will always be
of type ICE_PF_VSI. Remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the recursive way of adding the nodes to the layer in order
to reduce the stack usage. Instead the algorithm is modified to use
a while loop.
The previous code was scanning recursively the nodes horizontally.
The total stack consumption will be based on number of nodes present
on that layer. In some cases it can consume more stack.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Retry sending some AQ commands, as result of EBUSY AQ error.
ice_aqc_opc_get_link_topo
ice_aqc_opc_lldp_stop
ice_aqc_opc_lldp_start
ice_aqc_opc_lldp_filter_ctrl
This change follows the latest guidelines from HW team. It is
better to retry the same AQ command several times, as the result
of EBUSY, instead of returning error to the caller right away.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If veb-stats was enabled, the ethtool stats triggered a warning
due to invalid size: 'unexpected stat size for veb.tc_%u_tx_packets'.
This was due to an incorrect structure definition for the statistics.
Structures and functions have been improved in line with requirements
for the presentation of statistics, in particular for the functions:
'i40e_add_ethtool_stats' and 'i40e_add_stat_strings'.
Fixes: 1510ae0be2 ("i40e: convert VEB TC stats to use an i40e_stats array")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix so that single packets are received immediately instead of in
batches of 8. If you sent 1 pps to a system, you received 8 packets
every 8 seconds instead of 1 packet every second. The problem behind
this was that the work_done reporting from the Tx part of the driver
was broken. The work_done reporting in i40e controls not only the
reporting back to the napi logic but also the setting of the interrupt
throttling logic. When Tx or Rx reports that it has more to do,
interrupts are throttled or coalesced and when they both report that
they are done, interrupts are armed right away. If the wrong work_done
value is returned, the logic will start to throttle interrupts in a
situation where it should have just enabled them. This leads to the
undesired batching behavior seen in user-space.
Fix this by returning the correct boolean value from the Tx xsk
zero-copy path. Return true if there is nothing to do or if we got
fewer packets to process than we asked for. Return false if we got as
many packets as the budget since there might be more packets we can
process.
Fixes: 3106c580fb ("i40e: Use batched xsk Tx interfaces to increase performance")
Reported-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed new static analysis findings:
"warn: inconsistent indenting" - introduced lately,
reported with lkp and smatch build.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The following is reported by checkpatch, correct it.
-----------------------------------------------
drivers/net/ethernet/intel/ice/ice_adminq_cmd.h
-----------------------------------------------
WARNING:NETWORKING_BLOCK_COMMENT_STYLE: networking block comments don't use an empty /* line, use /* Comment...
FILE: drivers/net/ethernet/intel/ice/ice_adminq_cmd.h:1428:
+/*
+ * Send to PF command (indirect 0x0801) ID is only used by PF
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
A few style issues reported by checkpatch have snuck into the code; resolve
the style issues.
COMPLEX_MACRO: Macros with complex values should be enclosed in parentheses
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, ice_vsi_setup_q_map() depends on the VSI's rss_size. However,
the Rx Queue Mapping section of the VSI context has no dependency on RSS.
Instead, limit the maximum number of Rx queues per TC based on the Rx
Queue mapping section of the VSI context, which currently allows for up
to 256 Rx queues per TC.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Align all ptype bitmap to follow ice_ptypes_xxx prefix.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use *malloc() instead of *calloc() when allocating only a single object as
opposed to an array of objects.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check for bail out condition before calling ice_aq_sff_eeprom
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit a012dca9f7 ("ice: add ethtool -m support for reading i2c eeprom
modules") unnecessarily added the ICE_AQ_FLAG_BUF flag to the descriptor
when sending the indirect Read/Write SFF EEPROM AQ command. The flag is
already added later in the code flow for all indirect AQ commands, i.e.
commands that provide an additional data buffer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change link misconfiguration message since the configuration
could be intended by the user.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is an issue when the Tx or Rx ring size increases using
'ethtool -L ...' where the new rings don't get the correct ITR
values because when we rebuild the VSI we don't know that some
of the rings may be new.
Fix this by looking at the original number of rings and
determining if the rings in ice_vsi_rebuild_set_coalesce()
were not present in the original rings received in
ice_vsi_rebuild_get_coalesce().
Also change the code to return an error if we can't allocate
memory for the coalesce data in ice_vsi_rebuild().
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are two package versions in the package binary. Today, these two
version numbers are the same. However, in the future that may change.
Update code to use the package info from the ice segment metadata
section, which is the package information that is actually downloaded to
the firmware during the download package process.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once a netdev is registered, the corresponding network interface can
be immediately used by userspace utilities (like say NetworkManager).
This can be problematic if the driver technically isn't fully up yet.
Move netdev registration to the end of probe, as by this time the
driver data structures and device will be initialized as expected.
However, delaying netdev registration causes a failure in the aRFS flow
where netdev->reg_state == NETREG_REGISTERED condition is checked. It's
not clear why this check was added to begin with, so remove it.
Local testing didn't indicate any issues with this change.
The state bit check in ice_open was put in as a stop-gap measure to
prevent a premature interface up operation. This is no longer needed,
so remove it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable and configure XPS. The driver code implemented sets up the Transmit
Packet Steering Map, which in turn will be used by the kernel in queue
selection during Tx.
Signed-off-by: Benita Bose <benita.bose@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove repeated words "to" and "try".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As per the spec, the WoL control word read from the NVM should be
interpreted as port numbers, and not PF numbers. So when checking
if WoL supported, use the port number instead of the PF ID.
Also, ice_is_wol_supported doesn't really need a pointer to the pf
struct, but just needs a pointer to the hw instance.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add handling of allocation fault for ice_vsi_list_map_info.
Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.
Fixes: 9daf8208dd ("ice: Add support for switch filter programming")
Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com>
Co-developed-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The original purpose of the ICE_DCBNL_DEVRESET was to protect
the driver during DCBNL device resets. But, the flow for
DCBNL device resets now consists of only calls up the stack
such as dev_close() and dev_open() that will result in NDO calls
to the driver. These will be handled with state changes from the
stack. Also, there is a problem of the dev_close and dev_open
being blocked by checks for reset in progress also using the
ICE_DCBNL_DEVRESET bit.
Since the ICE_DCBNL_DEVRESET bit is not necessary for protecting
the driver from DCBNL device resets and it is actually blocking
changes coming from the DCBNL interface, remove the bit from the
PF state and don't block driver function based on DCBNL reset in
progress.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the order of number of array members and member size parameters in a
*calloc() call.
Fixes: b3c3890489 ("ice: avoid unnecessary single-member variable-length structs")
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a possibility of race between ice_open or ice_stop calls
performed by OS and reset handling routine both trying to modify VSI
resources. Observed scenarios:
- reset handler deallocates memory in ice_vsi_free_arrays and ice_open
tries to access it in ice_vsi_cfg_txq leading to driver crash
- reset handler deallocates memory in ice_vsi_free_arrays and ice_close
tries to access it in ice_down leading to driver crash
- reset handler clears port scheduler topology and sets port state to
ICE_SCHED_PORT_STATE_INIT leading to ice_ena_vsi_txq fail in ice_open
To prevent this additional checks in ice_open and ice_stop are
introduced to make sure that OS is not allowed to alter VSI config while
reset is in progress.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iSCSI can use both TCP ports 860 and 3260. However, in our current
implementation, the ice_aqc_opc_get_cee_dcb_cfg (0x0A07) AQ command
doesn't provide a way to communicate the protocol port number to the
AQ's caller. Thus, we assume that 3260 is the iSCSI port number at the
AQ's caller layer.
Rely on the dcbx-willing mode, desired QoS and remote QoS configuration to
determine which port number that iSCSI will use.
Fixes: 0ebd3ff13c ("ice: Add code for DCB initialization part 2/4")
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac8 ("ice: Add support for control queues")
Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
An incorrect NVM update procedure can result in the driver failing probe.
In this case, the recommended resolution method is to update the NVM
using the right procedure. However, if the driver fails probe, the user
will not be able to update the NVM. So do not fail probe on link/PHY
errors.
Fixes: 1a3571b593 ("ice: restore PHY settings on media insertion")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for the XDP_REDIRECT action which enables XDP programs to
redirect packets arriving at I225 NIC. It also implements the
ndo_xdp_xmit ops, enabling the igc driver to transmit packets forwarded
to it by xdp programs running on other interfaces.
The patch tweaks the driver's page counting and recycling scheme as
described in the following two commits and implemented by other Intel
drivers in order to properly support XDP_REDIRECT action:
commit 8ce29c679a ("i40e: tweak page counting for XDP_REDIRECT")
commit 75aab4e10a ("i40e: avoid premature Rx buffer reuse")
This patch has been tested with the sample apps "xdp_redirect_cpu" and
"xdp_redirect_map" located in samples/bpf/.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for XDP_TX action which enables XDP programs to transmit
back receiving frames.
I225 controller has only 4 Tx hardware queues. Since XDP programs may
not even issue an XDP_TX action, this patch doesn't reserve dedicated
queues just for XDP like other Intel drivers do. Instead, the queues
are shared between the network stack and XDP. The netdev queue lock is
used to ensure mutual exclusion.
Since frames can now be transmitted via XDP_TX, the igc_tx_buffer
structure is modified so we are able to save a reference to the xdp
frame for later clean up once the packet is transmitted. The tx_buffer
is mapped to either a skb or a xdpf so we use a union to save the skb
or xdpf pointer and have a bit in tx_flags to indicate which field to
use.
This patch has been tested with the sample app "xdp2" located in
samples/bpf/ dir.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the initial XDP support to the igc driver. For now, only XDP_PASS,
XDP_DROP, XDP_ABORTED actions are supported. Upcoming patches will add
support for the remaining XDP actions.
XDP configuration helpers are defined in a new file, igc_xdp.c. These
helpers are utilized in igc_main.c to implement the ndo_bpf callback.
XDP-related code that belongs to the driver's hot path is landed in
igc_main.c.
By default, the driver uses Rx buffers with 2 KB size. When XDP is
enabled, it uses larger buffers so we have enough space to accommodate
the headroom and tailroom required by XDP infrastructure. Also, the
driver doesn't support XDP functionality with frames that span over
multiple buffers so jumbo frames are not allowed for now.
The approach implemented follows the approach implemented in other Intel
drivers as much as possible for the sake of consistency across the
drivers.
Quick comment regarding igc_build_skb(): this patch doesn't touch it
because the function is never called. It seems its support is
incomplete/in progress. The function was added by commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers") but
ring_uses_build_skb() always return False since the IGC_RING_FLAG_RX_
BUILD_SKB_ENABLED isn't set anywhere in the driver code.
This patch has been tested with the sample app "xdp1" located in
samples/bpf/ dir.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While commit 13b5b7fd6a ("igc: Add support for Tx/Rx rings")
introduced code to handle larger packet buffers, it missed the
set/clear helpers which enable/disable that feature. Introduce
the missing helpers which will be use in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the Rx timestamp handling in preparation to land
XDP support.
Rx timestamps are put in the Rx buffer by hardware, before the packet
data. When creating the xdp buffer, we will need to check the Rx
descriptor to determine if the buffer contains timestamp information
and consider the offset when setting xdp.data.
The Rx descriptor check is already done in igc_construct_skb(). To
avoid code duplication, this patch moves the timestamp handling to
igc_clean_rx_irq() so both skb and xdp paths can reuse it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The RX frame truesize calculation is scattered throughout the RX code.
This patch creates the helper function igc_get_rx_frame_truesize() and
uses it where applicable.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igc driver implements the same page recycling scheme from other
Intel drivers which reuses the page by flipping the buffer. The code
to handle buffer flips is duplicated in many locations so introduce
the igc_rx_buffer_flip() helper and use it where applicable.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'skb' argument from igc_tx_cmd_type() is not used so remove it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup TC before the i40e_setup_pf_switch() call.
Memory must be initialized for all the queues
before using its resources.
Previously it could be possible that a call:
xdp_rxq_info_reg(&rx_ring->xdp_rxq, rx_ring->netdev,
rx_ring->queue_index, rx_ring->q_vector->napi.napi_id);
was made with q_vector being null.
Oops could show up with the following sequence:
- no driver loaded
- FW LLDP agent is on (flag disable-fw-lldp:off)
- link is up
- DCB configured with number of Traffic Classes that will not divide
completely the default number of queues (usually cpu cores)
- driver load
- set private flag: disable-fw-lldp:on
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Fixes: b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.
Fixes: d43d60e5eb ("i40e: ensure reset occurs when disabling VF")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add Asym_Pause to supported link modes (it is supported by HW).
Lack of Asym_Pause in supported modes can cause several problems,
i.e. it won't be possible to turn the autonegotiation on
with asymmetric pause settings (i.e. Tx on, Rx off).
Fixes: 4e91bcd5d4 ("i40e: Finish implementation of ethtool get settings")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding a couple of break statements instead of
just letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A bunch of header comments were showing warnings when compiling
with W=1. Fix them all at once. This changes only comments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct reported warnings for "warning: expecting prototype for ...
Prototype was for ... instead"
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option.
The user-def 0xAAAABBBBCCCCDDDD: BBBB is the 2 byte pattern while AAAA
corresponds to its offset in the packet. Similarly DDDD is the 2 byte
pattern with CCCC being the corresponding offset. The offset ranges from
0x0 to 0x1F7 (up to 504 bytes into the packet). The offset starts from
the beginning of the packet.
This feature can be used to allow customers to set flow director rules
for protocols headers that are beyond standard ones supported by ethtool
(e.g. PFCP or GTP-U).
Like for matching GTP-U's TEID value 0x10203040:
ethtool -N ens787f0v0 flow-type udp4 dst-port 2152 \
user-def 0x002e102000303040 action 13
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Support the addition and deletion of Ethernet filters.
Supported fields are: proto
Supported flow-types are: ether
Example usage:
ethtool -N ens787f0v0 flow-type ether proto 0x8863 action 6
ethtool -N ens787f0v0 flow-type ether proto 0x8864 action 7
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable ethtool ntuple filter support on the VF driver using the virtchnl
interface to the PF driver and the Flow director functionality in the
hardware.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable returning FDIR completion status by checking the
ctrl_vsi Rx queue descriptor value.
To enable returning FDIR completion status from ctrl_vsi Rx queue,
COMP_Queue and COMP_Report of FDIR filter programming descriptor
needs to be properly configured. After program request sent to ctrl_vsi
Tx queue, ctrl_vsi Rx queue interrupt will be triggered and
completion status will be returned.
Driver will first issue request in ice_vc_fdir_add_fltr(), then
pass FDIR context to the background task in interrupt service routine
ice_vc_fdir_irq_handler() and finally deal with them in
ice_flush_fdir_ctx(). ice_flush_fdir_ctx() will check the descriptor's
value, fdir context, and then send back virtual channel message to VF
by calling ice_vc_add_fdir_fltr_post(). An additional timer will be
setup in case of hardware interrupt timeout.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new FDIR filter type to forward GTPU packets by matching TEID or QFI.
The filter is only enabled when COMMS DDP package is downloaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new filter type that allow forward non-IP Ethernet packets base on its
ethertype. The filter is only enabled when COMMS DDP package is loaded.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new actions support for VF FDIR:
A passthrough action does not specify the destination queue, but
just allow the packet go to next pipeline stage, a typical use
cases is combined with a software mark (FDID) action.
Allow specify a 2^n continuous queues as the destination of a FDIR rule.
Packet distribution is based on current RSS configure.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add basic FDIR flow list and pattern / action parse functions for VF.
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The virtual channel is going to be extended to support FDIR and
RSS configure from AVF. New data structures and OP codes will be
added, the patch enable the FDIR part.
To support above advanced AVF feature, we need to figure out
what kind of data structure should be passed from VF to PF to describe
an FDIR rule or RSS config rule. The common part of the requirement is
we need a data structure to represent the input set selection of a rule's
hash key.
An input set selection is a group of fields be selected from one or more
network protocol layers that could be identified as a specific flow.
For example, select dst IP address from an IPv4 header combined with
dst port from the TCP header as the input set for an IPv4/TCP flow.
The patch adds a new data structure virtchnl_proto_hdrs to abstract
a network protocol headers group which is composed of layers of network
protocol header(virtchnl_proto_hdr).
A protocol header contains a 32 bits mask (field_selector) to describe
which fields are selected as input sets, as well as a header type
(enum virtchnl_proto_hdr_type). Each bit is mapped to a field in
enum virtchnl_proto_hdr_field guided by its header type.
+------------+-----------+------------------------------+
| | Proto Hdr | Header Type A |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
|Proto Hdrs | Proto Hdr | Header Type B |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | Proto Hdr | Header Type C |
| | +------------------------------+
| | | BIT 31 | ... | BIT 1 | BIT 0 |
| |-----------+------------------------------+
| | .... |
+-------------------------------------------------------+
All fields in enum virtchnl_proto_hdr_fields are grouped with header type
and the value of the first field of a header type is always 32 aligned.
enum proto_hdr_type {
header_type_A = 0;
header_type_B = 1;
....
}
enum proto_hdr_field {
/* header type A */
header_A_field_0 = 0,
header_A_field_1 = 1,
header_A_field_2 = 2,
header_A_field_3 = 3,
/* header type B */
header_B_field_0 = 32, // = header_type_B << 5
header_B_field_0 = 33,
header_B_field_0 = 34
header_B_field_0 = 35,
....
};
So we have:
proto_hdr_type = proto_hdr_field / 32
bit offset = proto_hdr_field % 32
To simply the protocol header's operations, couple help macros are added.
For example, to select src IP and dst port as input set for an IPv4/UDP
flow.
we have:
struct virtchnl_proto_hdr hdr[2];
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[0], IPV4)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[0], IPV4, SRC)
VIRTCHNL_SET_PROTO_HDR_TYPE(&hdr[1], UDP)
VIRTCHNL_ADD_PROTO_HDR_FIELD(&hdr[1], UDP, DST)
The byte array is used to store the protocol header of a training package.
The byte array must be network order.
The patch added virtual channel support for iAVF FDIR add/validate/delete
filter. iAVF FDIR is Flow Director for Intel Adaptive Virtual Function
which can direct Ethernet packets to the queues of the Network Interface
Card. Add/delete command is adding or deleting one rule for each virtual
channel message, while validate command is just verifying if this rule
is valid without any other operations.
To add or delete one rule, driver needs to config TCAM and Profile,
build training packets which contains the input set value, and send
the training packets through FDIR Tx queue. In addition, driver needs to
manage the software context to avoid adding duplicated rules, deleting
non-existent rule, input set conflicts and other invalid cases.
NOTE:
Supported pattern/actions and their parse functions are not be included in
this patch, they will be added in a separate one.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Simei Su <simei.su@intel.com>
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We are going to enable FDIR configure for AVF through virtual channel.
The first step is to add helper functions to support control VSI setup.
A control VSI will be allocated for a VF when AVF creates its
first FDIR rule through ice_vf_ctrl_vsi_setup().
The patch will also allocate FDIR rule space for VF's control VSI.
If a VF asks for flow director rules, then those should come entirely
from the best effort pool and not from the guaranteed pool. The patch
allow a VF VSI to have only space in the best effort rules.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separate IPv4 and IPv6 ptype bit mask table into 2 tables:
with or without L4 protocols.
When a flow filter without any l4 type is specified, the
ICE_FLOW_SEG_HDR_IPV_OTHER flag can be used to describe if user
want to create a IP rule target for all IP packet or just IP
packet without l4 header.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To apply different input set for GTP-U packet with or without extend
header as well as GTP-U uplink and downlink, we need to add TCAM mask
matching capability. This allows comprehending different PTYPE
attributes by examining flags from the parser. Using this method,
different profiles can be used by examining flag values from the parser.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol support in flow filter, these
include PPPoE, L2TPv3, GTP, PFCP, ESP and AH.
Signed-off-by: Ting Xu <ting.xu@intel.com>
Signed-off-by: Yahui Cao <yahui.cao@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To support FDIR input set with protocol field like DSCP, TTL,
PROT, etc. which is not word aligned, we need to enable field
vector masking.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add more protocol and field support for flow filter include:
ETH, VLAN, ICMP, ARP and TCP flag.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Chen Bo <BoX.C.Chen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The function e1000e_pm_prepare() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6926:12:
warning: 'e1000e_pm_prepare' defined but not used [-Wunused-function]
6926 | static int e1000e_pm_prepare(struct device *dev)
| ^~~~~~~~~~~~~~~~~
Fixes: ccf8b940e5 ("e1000e: Leverage direct_complete to speed up s2ram")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warnings:
./drivers/net/ethernet/intel/igc/igc_main.c:4961:2-14: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4955:2-14: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4933:1-13: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4592:1-24: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4438:2-25: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4396:2-25: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4018:2-25: WARNING:
Assignment of 0/1 to bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
MII_CR_LOOPBACK masks not in use in i225 device and can be removed.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Force PHY speed not supported for i225 devices.
MII_CR_SPEED masks not in use in i225 device and can be removed.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
MII_CR_RESET mask not in use in i225 device and can be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a couple of checks to make sure timestamping is on and that the
timestamp value from DMA is valid. This avoids any functional issues
that could come from a misinterpreted time stamp.
One of the functions changed doesn't need a return value added because
there was no value in checking from the calling locations.
While here, fix a couple of reverse christmas tree issues next to
the code being changed.
Fixes: f56e7bba22 ("igb: Pull timestamp from fragment before adding it to skb")
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The include guard "_E1000_HW_H_" is used by two separate header files in
two different drivers (e1000/e1000_hw.h and igb/e1000_hw.h). Using the
same include guard macro in more than one header file may cause
unexpected behavior from the compiler. Fix this by renaming the
duplicate guard in the igb driver.
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The include guard "_E1000_HW_H_" is used by header files in three
different drivers (e1000/e1000_hw.h, e1000e/hw.h, and igb/e1000_hw.h).
Using the same include guard macro in more than one header file may
cause unexpected behavior from the compiler. Fix the duplicate include
guard in the e1000e driver by renaming it.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
Update the Intel drivers to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-03-16
This series contains updates to i40e, ixgbe, and ice drivers.
Magnus Karlsson says:
Optimize run_xdp_zc() for the XDP program verdict being XDP_REDIRECT
in the xsk zero-copy path. This path is only used when having AF_XDP
zero-copy on and in that case most packets will be directed to user
space. This provides around 100k extra packets in throughput on my
server when running l2fwd in xdpsock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-03-15
This series contains updates to e1000e only.
Chen Yu says:
The NIC is put in runtime suspend status when there is no cable connected.
As a result, it is safe to keep non-wakeup NIC in runtime suspended during
s2ram because the system does not rely on the NIC plug event nor WoL to
wake up the system. Besides that, unlike the s2idle, s2ram does not need to
manipulate S0ix settings during suspend.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although there is platform issue of runtime suspend support
on CNP, it would be more flexible to let the user decide whether
to disable runtime or not because:
1. This can be done in userspace via
echo on > /sys/devices/pci0000\:00/0000\:00\:1f.d/power/control
2. More and more NICs would support runtime suspend, disabling the
runtime suspend on them by default would impact the validation.
Only disable runtime suspend on CNP in case of any user space regression.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The NIC is put in runtime suspend status when there is no cable connected.
As a result, it is safe to keep non-wakeup NIC in runtime suspended during
s2ram because the system does not rely on the NIC plug event nor WoL to wake
up the system. Besides that, unlike the s2idle, s2ram does not need to
manipulate S0ix settings during suspend.
This patch introduces the .prepare() for e1000e so that if the NIC is runtime
suspended the subsequent suspend/resume hooks will be skipped so as to speed
up the s2ram. The pm core will check whether the NIC is a wake up device so
there's no need to check it again in .prepare(). DPM_FLAG_SMART_PREPARE flag
should be set during probe to ask the pci subsystem to honor the driver's
prepare() result. Besides, the NIC remains runtime suspended after resumed
from s2ram as there is no need to resume it.
Tested on i7-2600K with 82579V NIC
Before the patch:
e1000e 0000:00:19.0: pci_pm_suspend+0x0/0x160 returned 0 after 225146 usecs
e1000e 0000:00:19.0: pci_pm_resume+0x0/0x90 returned 0 after 140588 usecs
After the patch:
echo disabled > //sys/devices/pci0000\:00/0000\:00\:19.0/power/wakeup
becomes 0 usecs because the hooks will be skipped.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
s/structue/structure/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize ice_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Optimize ixgbe_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little under 100k extra
packets in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Optimize i40e_run_xdp_zc() for the XDP program verdict being
XDP_REDIRECT in the xsk zero-copy path. This path is only used when
having AF_XDP zero-copy on and in that case most packets will be
directed to user space. This provides a little over 100k extra packets
in throughput on my server when running l2fwd in xdpsock.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Igb needs a similar fix as commit 75aab4e10a ("i40e: avoid
premature Rx buffer reuse")
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Longer explanation:
Intel NICs have a recycle mechanism. The main idea is that a page is
split into two parts. One part is owned by the driver, one part might
be owned by someone else, such as the stack.
t0: Page is allocated, and put on the Rx ring
+---------------
used by NIC ->| upper buffer
(rx_buffer) +---------------
| lower buffer
+---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX
t1: Buffer is received, and passed to the stack (e.g.)
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 1
t2: Buffer is received, and redirected
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
Now, prior calling xdp_do_redirect():
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 2
This means that buffer *cannot* be flipped/reused, because the skb is
still using it.
The problem arises when xdp_do_redirect() actually frees the
segment. Then we get:
page count == USHRT_MAX - 1
rx_buffer->pagecnt_bias == USHRT_MAX - 2
From a recycle perspective, the buffer can be flipped and reused,
which means that the skb data area is passed to the Rx HW ring!
To work around this, the page count is stored prior calling
xdp_do_redirect().
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ixgbe_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on __IXGBE_RX_BUILD_SKB_ENABLED flag.
Currently, the callsite of mentioned function is placed incorrectly
within ixgbe_setup_rx_resources() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.
Fix this by moving ixgbe_rx_offset() to ixgbe_configure_rx_ring() after
the flag setting, which happens to be set in ixgbe_set_rx_buffer_len.
Fixes: c0d4e9d223 ("ixgbe: store the result of ixgbe_rx_offset() onto ixgbe_ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on ICE_RX_FLAGS_RING_BUILD_SKB flag as well as XDP prog presence.
Currently, the callsite of mentioned function is placed incorrectly
within ice_setup_rx_ring() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.
Fix this by moving ice_rx_offset() to ice_setup_rx_ctx() after the flag
setting.
Fixes: f1b1f409bf ("ice: store the result of ice_rx_offset() onto ice_ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_rx_offset(), that is supposed to initialize the Rx buffer headroom,
relies on I40E_RXR_FLAGS_BUILD_SKB_ENABLED flag.
Currently, the callsite of mentioned function is placed incorrectly
within i40e_setup_rx_descriptors() where Rx ring's build skb flag is not
set yet. This causes the XDP_REDIRECT to be partially broken due to
inability to create xdp_frame in the headroom space, as the headroom is
0.
For the record, below is the call graph:
i40e_vsi_open
i40e_vsi_setup_rx_resources
i40e_setup_rx_descriptors
i40e_rx_offset() <-- sets offset to 0 as build_skb flag is set below
i40e_vsi_configure_rx
i40e_configure_rx_ring
set_ring_build_skb_enabled(ring) <-- set build_skb flag
Fix this by moving i40e_rx_offset() to i40e_configure_rx_ring() after
the flag setting.
Fixes: f7bb0d71d6 ("i40e: store the result of i40e_rx_offset() onto i40e_ring")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Co-developed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the wrong napi work done reporting in the xsk path of the ice
driver. The code in the main Rx processing loop was written to assume
that the buffer allocation code returns true if all allocations where
successful and false if not. In contrast with all other Intel NIC xsk
drivers, the ice_alloc_rx_bufs_zc() has the inverted logic messing up
the work done reporting in the napi loop.
This can be fixed either by inverting the return value from
ice_alloc_rx_bufs_zc() in the function that uses this in an incorrect
way, or by changing the return value of ice_alloc_rx_bufs_zc(). We
chose the latter as it makes all the xsk allocation functions for
Intel NICs behave in the same way. My guess is that it was this
unexpected discrepancy that gave rise to this bug in the first place.
Fixes: 5bb0c4b5eb ("ice, xsk: Move Rx allocation out of while-loop")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is one e1e_wphy() call in e1000_set_d0_lplu_state_82571
that we have caught its return value but lack further handling.
Check and terminate the execution flow just like other e1e_wphy()
in this function.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b7 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The comment describing the timestamps layout in the packet buffer is
wrong and the code is actually retrieving the timestamp in Timer 1
reference instead of Timer 0. This hasn't been a big issue so far
because hardware is configured to report both timestamps using Timer 0
(see IGC_SRRCTL register configuration in igc_ptp_enable_rx_timestamp()
helper). This patch fixes the comment and the code so we retrieve the
timestamp in Timer 0 reference as expected.
This patch also takes the opportunity to get rid of the hw.mac.type check
since it is not required.
Fixes: 81b055205e ("igc: Add support for RX timestamping")
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Supported Pause Frame always display "No" even though the Advertised
pause frame showing the correct setting based on the pause parameters via
ethtool. Set bit in link_ksettings to "Supported" for Pause Frame.
Before output:
Supported pause frame use: No
Expected output:
Supported pause frame use: Symmetric
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix Pause Frame Advertising when getting the advertisement via ethtool.
Remove setting the "advertising" bit in link_ksettings during default
case when Tx and Rx are in off state with Auto Negotiate off.
Below is the original output of advertisement link during Tx and Rx off:
Advertised pause frame use: Symmetric Receive-only
Expected output:
Advertised pause frame use: No
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This commit applies to the igc_reset_task the same changes that
were applied to the igb driver in commit 024a8168b7 ("igb:
reinit_locked() should be called with rtnl_lock")
and fix possible race in reset subtask.
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As explained in commit 29d98f54a4 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.
Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When iavf_process_config() fails, no error return code of
iavf_init_get_resources() is assigned.
To fix this bug, err is assigned with the return value of
iavf_process_config(), and then err is checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ixgbe_fdir_write_perfect_filter_82599() fails,
input allocated by kzalloc() has not been freed,
which leads to memleak.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Based on talks and indirect references ixgbe IPsec offlod do not
support IPsec tunnel mode offload. It can only support IPsec transport
mode offload. Now explicitly fail when creating non transport mode SA
with offload to avoid false performance expectations.
Fixes: 63a67fe229 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Antony Antony <antony@phenome.org>
Acked-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-02-22
Dave corrects reporting of max TCs to use the value from hardware
capabilities and setting of DCBx capability bits when changing between
SW and FW LLDP.
Brett fixes trusted VF multicast promiscuous not receiving expected
packets and corrects VF max packet size when a port VLAN is configured.
Henry updates available RSS queues following a change in channel count
with a user defined LUT.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: update the number of available RSS queues
ice: Fix state bits on LLDP mode switch
ice: Account for port VLAN in VF max packet size calculation
ice: Set trusted VF as default VSI when setting allmulti on
ice: report correct max number of TCs
====================
Link: https://lore.kernel.org/r/20210222235814.834282-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-02-19
This series contains updates to i40e driver only.
Slawomir resolves an issue with the IPv6 extension headers being
processed incorrectly.
Keita Suzuki fixes a memory leak on probe failure.
Mateusz initializes AQ command structures to zero to comply with
spec, fixes FW flow control settings being overwritten and resolves an
issue with adding VLAN filters after enabling FW LLDP. He also adds
an additional check when adding TC filter as the current check doesn't
properly distinguish between IPv4 and IPv6.
Sylwester removes setting disabled bit when syncing filters as this
prevents VFs from completing setup.
Norbert cleans up sparse warnings.
v2:
- Fix fixes tag on patch 7
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix endianness conversions
i40e: Fix add TC filter for IPv6
i40e: Fix VFs not created
i40e: Fix addition of RX filters after enabling FW LLDP agent
i40e: Fix overwriting flow control settings during driver loading
i40e: Add zero-initialization of AQ command structures
i40e: Fix memory leak in i40e_probe
i40e: Fix flow for IPv6 next header (extension header)
====================
Link: https://lore.kernel.org/r/20210219213606.2567536-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was possible to have Rx queues that were not available for use
by RSS. This would happen when increasing the number of Rx queues
while there was a user defined RSS LUT.
Always update the number of available RSS queues when changing the
number of Rx queues.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DCBX_CAP bits were not being adjusted when switching
between SW and FW controlled LLDP.
Adjust bits to correctly indicate which mode the
LLDP logic is in.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if an AVF driver doesn't account for the possibility of a
port VLAN when determining its max packet size then packets at MTU will
be dropped. It is not the VF driver's responsibility to account for a
port VLAN so fix this. To fix this, do the following:
1. Add a function that determines the max packet size a VF is allowed by
using the port's max packet size and whether the VF is in a port
VLAN. If a port VLAN is configured then a VF's max packet size will
always be the port's max packet size minus VLAN_HLEN. Otherwise it
will be the port's max packet size.
2. Use this function to verify the max packet size from the VF.
3. If there is a port VLAN configured then add 4 bytes (VLAN_HLEN) to
the VF's max packet size configuration.
Also, the VIRTCHNL_OP_GET_VF_RESOURCES message provides the capability
to communicate a VF's max packet size. Use the new function for this
purpose.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF will only set a trusted VF as the default VSI when it
requests FLAG_VF_UNICAST_PROMISC over VIRTCHNL. However, when
FLAG_VF_MULTICAST_PROMISC is set it's expected that the trusted VF will
see multicast packets that don't have a matching destination MAC in the
devices internal switch. Fix this by setting the trusted VF as the
default VSI if either FLAG_VF_UNICAST_PROMISC or
FLAG_VF_MULTICAST_PROMISC is set.
Fixes: 01b5e89aab ("ice: Add VF promiscuous support")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the driver currently, we are reporting max number of TCs
to the DCBNL callback as a kernel define set to 8. This is
preventing userspace applications performing DCBx to correctly
down map the TCs from requested to actual values.
Report the actual max TC value to userspace from the capability
struct.
Fixes: b94b013eb6 ("ice: Implement DCBNL support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixes the following sparse warnings:
i40e_main.c:5953:32: warning: cast from restricted __le16
i40e_main.c:8008:29: warning: incorrect type in assignment (different base types)
i40e_main.c:8008:29: expected unsigned int [assigned] [usertype] ipa
i40e_main.c:8008:29: got restricted __le32 [usertype]
i40e_main.c:8008:29: warning: incorrect type in assignment (different base types)
i40e_main.c:8008:29: expected unsigned int [assigned] [usertype] ipa
i40e_main.c:8008:29: got restricted __le32 [usertype]
i40e_txrx.c:1950:59: warning: incorrect type in initializer (different base types)
i40e_txrx.c:1950:59: expected unsigned short [usertype] vlan_tag
i40e_txrx.c:1950:59: got restricted __le16 [usertype] l2tag1
i40e_txrx.c:1953:40: warning: cast to restricted __le16
i40e_xsk.c:448:38: warning: invalid assignment: |=
i40e_xsk.c:448:38: left side has type restricted __le64
i40e_xsk.c:448:38: right side has type int
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Fixes: 2a508c64ad ("i40e: fix VLAN.TCI == 0 RX HW offload")
Fixes: 3106c580fb ("i40e: Use batched xsk Tx interfaces to increase performance")
Fixes: 8f88b3034d ("i40e: Add infrastructure for queue channel support")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix insufficient distinction between IPv4 and IPv6 addresses
when creating a filter.
IPv4 and IPv6 are kept in the same memory area. If IPv6 is added,
then it's caught by IPv4 check, which leads to err -95.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When creating VFs they were sometimes not getting resources.
It was caused by not executing i40e_reset_all_vfs due to
flag __I40E_VF_DISABLE being set on PF. Because of this
IAVF was never able to finish setup sequence never
getting reset indication from PF.
Changed test_and_set_bit __I40E_VF_DISABLE in
i40e_sync_filters_subtask to test_bit and removed clear_bit.
This function should not set this bit it should only check
if it hasn't been already set.
Fixes: a7542b8760 ("i40e: check __I40E_VF_DISABLE bit in i40e_sync_filters_subtask")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix addition of VLAN filter for PF after enabling FW LLDP agent.
Changing LLDP Agent causes FW to re-initialize per NVM settings.
Remove default PF filter and move "Enable/Disable" to currently used
reset flag.
Without this patch PF would try to add MAC VLAN filter with default
switch filter present. This causes AQ error and sets promiscuous mode
on.
Fixes: c65e78f87f ("i40e: Further implementation of LLDP")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During driver loading flow control settings were written to FW
using a variable which was always zero, since it was being set
only by ethtool. This behavior has been corrected and driver
no longer overwrites the default FW/NVM settings.
Fixes: 373149fc99 ("i40e: Decrease the scope of rtnl lock")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Zero-initialize AQ command data structures to comply with
API specifications.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Fixes: f4492db16d ("i40e: Add NPAR BW get and set functions")
Signed-off-by: Andrzej Sawuła <andrzej.sawula@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with I40E_TX_CTX_EXT_IP_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a3fd9d8876 ("i40e/i40evf: Handle IPv6 extension headers in checksum offload")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable mfs_max is not initialized and is being compared to find
the maximum value. Fix this by initializing it to 0.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 90bc8e003b ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that the right argument to be passed is &tcp_ip6_spec->ip6dst,
not &tcp_ip6_spec->ip6src, when calling function ipv6_addr_any().
Addresses-Coverity-ID: 1501734 ("Copy-paste error")
Fixes: efca91e89b ("i40e: Add flow director support for IPv6")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output of ixgbe_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.
Add new 'rx_offset' field to ixgbe_ring that is meant to hold the
ixgbe_rx_offset() result and use it within ixgbe_clean_rx_irq().
Furthermore, use it within ixgbe_alloc_mapped_page().
Last but not least, un-inline the function of interest as it lives in .c
file so let compiler do the decision about the inlining.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Output of ice_rx_offset() is based on ethtool's priv flag setting, which
when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.
Add new 'rx_offset' field to ice_ring that is meant to hold the
ice_rx_offset() result and use it within ice_clean_rx_irq().
Furthermore, use it within ice_alloc_mapped_page().
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Output of i40e_rx_offset() is based on ethtool's priv flag setting,
which when changed, causes PF reset (disables napi, frees irqs, loads
different Rx mem model, etc.). This means that within napi its result is
constant and there is no reason to call it per each processed frame.
Add new 'rx_offset' field to i40e_ring that is meant to hold the
i40e_rx_offset() result and use it within i40e_clean_rx_irq().
Furthermore, use it within i40e_alloc_mapped_page().
Last but not least, un-inline the function of interest so that compiler
makes the decision about inlining as it lives in .c file.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fold the count decrement into the while-statement.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Whole zero-copy variant of clean Rx IRQ is executed when xsk_pool is
attached to rx_ring and it can happen only when XDP program is present
on interface. Therefore it is safe to assume that program is always
!NULL and there is no need for checking it in ice_run_xdp_zc.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
dev_validate_mtu checks that mtu value specified by user is not less
than min mtu and not greater than max allowed mtu. It is being done
before calling the ndo_change_mtu exposed by driver, so remove these
redundant checks in ice_change_mtu.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Similar thing has been done in i40e, as there is no real need for having
the sk_buff pointer in each rx_buf. Non-eop frames can be simply handled
on that pointer moved upwards to rx_ring.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There's no need for 'result' variable, we can directly return the
internal status based on action returned by xdp prog.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_is_non_eop had a leftover comment and unused skb argument which was
used for placing the skb onto rx_buf in case when current buffer was
non-eop one. This is not relevant anymore as commit e72e56597b
("i40e/i40evf: Moves skb from i40e_rx_buffer to i40e_ring") pulled the
non-complete skb handling out of rx_bufs up to rx_ring. Therefore,
let's adjust the function arguments that i40e_is_non_eop takes.
Furthermore, since there is already a function responsible for bumping
the ntc, make use of that and drop that logic from i40e_is_non_eop so
that the scope of this function is limited to what the name actually
states.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_cleanup_headers has a statement about check against skb being
linear or not which is not relevant anymore, so let's remove it.
Same case for i40e_can_reuse_rx_page, it references things that are not
present there anymore.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Net core handles the case where netdev has no xdp prog attached and
current prog is NULL. Therefore, remove such check within
i40e_xdp_setup.
Reviewed-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable ret is overwritten by the following call
i40e_clean_arq_element() and the assignment is useless, so remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow user to specify VLAN field and add it to flow director. Show VLAN
field in "ethtool -n ethx" command.
Handle VLAN type and tag field provided by ethtool command. Refactored
filter addition, by replacing static arrays with runtime dummy packet
creation, which allows specifying VLAN field.
Previously, VLAN field was omitted.
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow director for IPv6 is not supported.
1) Implementation of support for IPv6 flow director.
2) Added handlers for addition of TCP6, UDP6, SCTP6, IPv6.
3) Refactored legacy code to make it more generic.
4) Added packet templates for TCP6, UDP6, SCTP6, IPv6.
5) Added handling of IPv6 source and destination address for flow director.
6) Improved argument passing for source and destination portin TCP6, UDP6
and SCTP6.
7) Added handling of ethtool -n for IPv6, TCP6,UDP6, SCTP6.
8) Used correct bit flag regarding FLEXOFF field of flow director data
descriptor.
Without this patch, there would be no support for flow director on IPv6,
TCP6, UDP6, SCTP6.
Tested based on x710 datasheet by using:
ethtool -N enp133s0f0 flow-type tcp4 src-port 13 dst-port 37 user-def 0x44142 action 1
ethtool -N enp133s0f0 flow-type tcp6 src-port 13 dst-port 40 user-def 0x44142 action 2
ethtool -N enp133s0f0 flow-type udp4 src-port 20 dst-port 40 user-def 0x44142 action 3
ethtool -N enp133s0f0 flow-type udp6 src-port 25 dst-port 40 user-def 0x44142 action 4
ethtool -N enp133s0f0 flow-type sctp4 src-port 55 dst-port 65 user-def 0x44142 action 5
ethtool -N enp133s0f0 flow-type sctp6 src-port 60 dst-port 40 user-def 0x44142 action 6
ethtool -N enp133s0f0 flow-type ip4 src-ip 1.1.1.1 dst-ip 1.1.1.4 user-def 0x44142 action 7
ethtool -N enp133s0f0 flow-type ip6 src-ip fe80::3efd:feff:fe6f:bbbb dst-ip fe80::3efd:feff:fe6f:aaaa user-def 0x44142 action 8
Then send traffic from client which matches the criteria provided to ethtool.
Observe that packets are redirected to user set queues with ethtool -S <interface>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement Energy Efficient Ethernet (EEE) status getting & setting.
The i40e_get_eee() requesting PHY EEE capabilities from firmware.
The i40e_set_eee() function requests PHY EEE capabilities
from firmware and sets PHY EEE advertising to full abilities or 0
depending whether EEE is to be enabled or disabled.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks used by software based LLDP agent, which allows to
configure DCB feature from userspace.
Update copyright dates as appropriate.
If LLDP agent is turned off in BIOS, or after setting private flag
("disable-fw-lldp on"). The driver initialized DCB functionality with
default values, one traffic class with 100% bandwidth allocated.
The new netlink callbacks are required for software LLDP agent, it
must be able to acquire current DCB configuration of a network port
and apply DCB configuration changes, if required.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add extra handling on changing the "disable-fw-lldp" private
flag to properly initialize software based DCB feature.
Add default configuration of DCB functionality when Firmware
LLDP agent is turned off, in case of driver probe and device
reset on reconfiguration.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
Default configuration and new initialization flow for software based
DCB is required. If LLDP agent is turned off in BIOS, or after
setting private flag ("disable-fw-lldp on"). The driver initializes
DCB functionality with default values, one traffic class with 100%
bandwidth allocated.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add registers and definitions required for applying
DCB related hardware configuration.
Add functions responsible for calculating and setting proper
hardware configuration values for software based DCB functionality.
Add function responsible for invoking Admin Queue command, which
results in applying new DCB configuration to the hardware.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
New communication channel between software and hardware is required
for software driver. It must be able to calculate and configure all
the registers related for DCB feature.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-02-08
This series contains updates to i40e driver only.
Cristian makes improvements to driver XDP path. Avoids writing
next-to-clean pointer on every update, removes redundant updates of
cleaned_count and buffer info, creates a helper function to consolidate
XDP actions and simplifies some of the behavior.
Eryk adds messages to inform the user when MTU is larger than supported
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to link XDP prog with MTU larger than supported,
user is not informed why XDP linking fails. Adding proper
error message: "MTU too large to enable XDP".
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Consolidate the actions performed on the packet based on the XDP
program result into a separate function that is easier to read and
maintain. Simplify the i40e_construct_skb_zc function, so that the
input xdp buffer is always freed, regardless of whether the output
skb is successfully created or not. Simplify the behavior of the
i40e_clean_rx_irq_zc function, so that the current packet descriptor
is dropped when function i40_construct_skb_zc returns an error as
opposed to re-processing the same description on the next invocation.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, remove the redundant buffer info updates
(*bi = NULL). The buffers ready to be cleaned can easily be tracked
based on the ring next-to-clean variable, which is consistently
updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, remove the redundant updates of the cleaned_count
variable, as its value can be computed based on the ring next-to-clean
variable, which is consistently updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, avoid writing the ring next-to-clean pointer
value back to memory on every update, as it is not really necessary.
Instead, simply read it at initialization into a local copy, update
the local copy as necessary and write the local copy back to memory
after the last update.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
