Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When reading from the flash memory of the device, the ice driver has two
interfaces available to it. First, it can use a mediated interface via
firmware that allows specifying a module ID. This allows reading from
specific modules of the active flash bank.
The second interface available is to perform flat reads. This allows
complete access to the entire flash. However, using it requires the
software to handle calculating module location and interpret pointer
addresses.
While most data required is accessible through the convenient first
interface, certain flash contents are not. This includes the CSS header
information associated with the Option ROM and NVM banks, as well as any
access to the "inactive" banks used as scratch space for performing
flash updates.
In order to access all of the relevant flash contents, software must use
the flat reads. Rather than forcing all flows to perform flat read
calculations, introduce a new abstraction for reading from the flash:
ice_read_flash_module. This function provides an abstraction for reading
from either the active or inactive flash bank at the requested module.
This interface is very similar to the abstraction provided via firmware,
but allows access to additional modules, as well as providing
a mechanism to request access to both flash banks.
At first glance, it might make sense for this abstraction to allow
specifying precisely which bank (1st or 2nd) the caller wishes to read.
This is simpler to implement but more difficult to use. In practice,
most callers only know whether they want the active bank, or the
inactive bank. Rather than force callers to determine for themselves
which bank to read from, implement ice_read_flash_module in terms of
"active" vs "inactive". This significantly simplifies the implementation
at the caller level and is a more useful abstraction over the flash
contents.
Make use of this new interface to refactor reading of the main NVM
version information. Instead of using the firmware's mediated ShadowRAM
function, use the ice_read_flash_module abstraction.
To do this, notice that most reads of the NVM are going to be in 2-byte
word chunks. To simplify using ice_read_flash_module for this case,
ice_read_nvm_module is introduced. This is a simple wrapper around
ice_read_flash_module which takes the correct pointer address for the
NVM bank, and forces the 2-byte word format onto the caller.
When reading the NVM versions, some fields are read from the Shadow RAM.
The Shadow RAM is the first 64KB of flash memory, and is populated
during device load. Most fields are copied from a section within the
active NVM bank. In order to read this data from both the active and
inactive NVM banks, we need to read not from the first 64KB of flash,
but instead from the correct offset into the NVM bank. Introduce
ice_read_nvm_sr_copy for this purpose. This function wraps around
ice_read_nvm_module and has the same interface as the ice_read_sr_word,
with the exception of allowing the caller to specify whether to read the
active or inactive flash bank.
With this change, it is now trivial to refactor ice_get_nvm_ver_info to
read using the software mediated ice_read_flash_module interface instead
of relying on the firmware mediated interface. This will be used in the
following change to implement support for stored versions in the devlink
info report.
Additionally, the overall ice_read_flash_module interface will be used
and extended to support all three major flash banks, and additionally to
support reading the flash image security revision information.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice flash contains two copies of each of the NVM, Option ROM, and
Netlist modules. Each bank has a pointer word and a size word. In order
to correctly read from the active flash bank, the driver must calculate
the offset manually.
During NVM initialization, read the Shadow RAM control word and
determine which bank is active for each NVM module. Additionally, cache
the size and pointer values for use in calculating the correct offset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver uses an array of structures which link an info name with
a function that formats the associated version data into a string.
All existing format functions simply format already captured static data
from the driver hw structure. Future changes will introduce format
functions for reporting the versions of flash sections stored but not
yet applied. This type of version data is not stored as a member of the
hw structure. This is because (a) it might not yet exist in the case
there is no pending flash update, and (b) even if it does, it might
change such as if an update is canceled or replaced by a new update
before finalizing.
We could simply have each format function gather its own data upon being
called. However, in some cases the raw binary version data is
a combination of multiple different reported fields. Additionally, the
current interface doesn't have a way for the function to indicate that
the version doesn't exist.
Refactor this function interface to take a new ice_info_ctx structure
instead of the buffer pointer and length. This context structure allows
for future extensions to pre-gather version data that is stored within
the context struct instead of the hw struct.
Allocate this context structure initially at the start of
ice_devlink_info_get. We use dynamic allocation instead of a local stack
variable in order to avoid using too much kernel stack once we extend it
with additional data structures.
Modify the main loop that drives the info reporting so that the version
buffer string is always cleared between each format. Explicitly check
that the format function actually filled in a version string of non-zero
length. If the string is not provided, simply skip this version without
reporting an error. This allows for introducing format functions of
versions which may or may not be present, such as the version of
a pending update that has not yet been activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_info structure has become somewhat of a dumping ground for
all of the fields related to flash version. It holds the NVM version and
EETRACK id, the OptionROM info structure, the flash size, the ShadowRAM
size, and more.
A future change is going to add the ability to read the NVM version and
EETRACK ID from the inactive NVM bank. To make this simpler, it is
useful to have these NVM version info fields extracted to their own
structure.
Rename ice_nvm_info into ice_flash_info, and create a separate
ice_nvm_info structure that will contain the eetrack and NVM map
version. Move the netlist_ver structure into ice_flash_info and rename it
ice_netlist_info for consistency.
Modify the static ice_get_orom_ver_info to take the option rom structure
as a pointer. This makes it more obvious what portion of the hw struct
is being modified. Do the same for ice_get_netlist_ver_info.
Introduce a new ice_get_nvm_ver_info function, which will be similar to
ice_get_orom_ver_info and ice_get_netlist_ver_info, used to keep the NVM
version extraction code co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When erasing, notify userspace of how long we will potentially take to
erase a module. Doing so allows userspace to report the timeout, giving
a clear indication of the upper time bound of the operation.
Since we're re-using the erase timeout value, make it a macro rather
than a magic number.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current MSI-X enablement logic tries to enable best-case MSI-X
vectors and if that fails we only support a bare-minimum set. This
includes a single MSI-X for 1 Tx and 1 Rx queue and a single MSI-X
for the OICR interrupt. Unfortunately, the driver fails to load when we
don't get as many MSI-X as requested for a couple reasons.
First, the code to allocate MSI-X in the driver tries to allocate
num_online_cpus() MSI-X for LAN traffic without caring about the number
of MSI-X actually enabled/requested from the kernel for LAN traffic.
So, when calling ice_get_res() for the PF VSI, it returns failure
because the number of available vectors is less than requested. Fix
this by not allowing the PF VSI to allocation more than
pf->num_lan_msix MSI-X vectors and pf->num_lan_msix Rx/Tx queues.
Limiting the number of queues is done because we don't want more than
1 Tx/Rx queue per interrupt due to performance conerns.
Second, the driver assigns pf->num_lan_msix = 2, to account for LAN
traffic and the OICR. However, pf->num_lan_msix is only meant for LAN
MSI-X. This is causing a failure when the PF VSI tries to
allocate/reserve the minimum pf->num_lan_msix because the OICR MSI-X has
already been reserved, so there may not be enough MSI-X vectors left.
Fix this by setting pf->num_lan_msix = 1 for the failure case. Then the
ICE_MIN_MSIX accounts for the LAN MSI-X and the OICR MSI-X needed for
the failure case.
Update the related defines used in ice_ena_msix_range() to align with
the above behavior and remove the unused RDMA defines because RDMA is
currently not supported. Also, remove the now incorrect comment.
Fixes: 152b978a1f ("ice: Rework ice_ena_msix_range")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently users could create more channels than LAN MSI-X available.
This is happening because there is no check against pf->num_lan_msix
when checking the max allowed channels and will cause performance issues
if multiple Tx and Rx queues are tied to a single MSI-X. Fix this by not
allowing more channels than LAN MSI-X available in pf->num_lan_msix.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the driver to copy the MAC address configured in ndo_set_mac_address
into dev_addr, even if the MAC filter already exists in HW. In some
situations (e.g. bonding) the netdev's dev_addr could have been modified
outside of the driver, with no change to the HW filter, so the driver
cannot assume that they match.
Fixes: 757976ab16 ("ice: Fix check for removing/adding mac filters")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is based on a similar change to i40e by Slawomir Laba:
"i40e: Implement flow for IPv6 next header (extension header)".
When a packet contains an IPv6 header with next header which is
an extension header and not a protocol one, the kernel function
skb_transport_header called with such sk_buff will return a
pointer to the extension header and not to the TCP one.
The above explained call caused a problem with packet processing
for skb with encapsulation for tunnel with ICE_TX_CTX_EIPT_IPV6.
The extension header was not skipped at all.
The ipv6_skip_exthdr function does check if next header of the IPV6
header is an extension header and doesn't modify the l4_proto pointer
if it points to a protocol header value so its safe to omit the
comparison of exthdr and l4.hdr pointers. The ipv6_skip_exthdr can
return value -1. This means that the skipping process failed
and there is something wrong with the packet so it will be dropped.
Fixes: a4e82a81f5 ("ice: Add support for tunnel offloads")
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The packet classifier would occasionally misrecognize an IPv6 training
packet when the next protocol field was 0. The correct value for
unspecified protocol is IPPROTO_NONE.
Fixes: 165d80d6ad ("ice: Support IPv6 Flow Director filters")
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
napi_gro_receive() can never return GRO_DROP
GRO_DROP can only be returned from napi_gro_frags()
which is the other NAPI GRO entry point.
Followup patch will remove GRO_DROP, because drivers
are not supposed to call napi_gro_frags() if prior
napi_get_frags() has failed.
Note that I have left the gro_dropped variable. I leave to ice
maintainers the decision to further remove it from ethtool -S results.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the Rx side, the next_to_use index points to the next item in the
HW ring to be refilled/allocated, and next_to_clean points to the next
item to potentially be processed.
When the HW Rx ring is fully refilled, i.e. no packets has been
processed, the next_to_use will be next_to_clean - 1. When the ring is
fully processed next_to_clean will be equal to next_to_use. The latter
case is where a bug is triggered.
If the next_to_use bits are not cleared, and the "fully processed"
state is entered, a stale descriptor can be processed.
The skb-path correctly clear the status bit for the next_to_use
descriptor, but the AF_XDP zero-copy path did not do that.
This change adds the status bits clearing of the next_to_use
descriptor.
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead doing the check for allocation in each loop, move it outside
the while loop and do it every NAPI loop.
This change boosts the xdpsock rxdrop scenario with 15% more
packets-per-second.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20201211085410.59350-1-bjorn.topel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Fixes: efc2214b60 ("ice: Add support for XDP")
Reported-and-analyzed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add space to the end of 'Unknown' string in order to avoid
concatenation with 'bps' string when formatting netdev log message.
Signed-off-by: Simon Perron Caissy <simon.perron.caissy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When printing messages with ice_debug, align the printed string to the
origin line of the message in order to ease debugging and tracking
messages back to their source.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
sparse warns about cast to/from restricted types which is not
an actual problem; silence the warning.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The maximum Admin Queue buffer size and NVM shadow RAM sector size are both
4 Kilobytes. Some comments refer to those as 4Kb which can be confused with
4 Kilobits. Update the comments to use the commonly used KB symbol instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vlan_ena was introduced to track whether VLAN filters are enabled on
the device, but
1) checking for num_vlan > 1 already gives us this information, and is
currently used in this way throughout the code
2) the logic for vlan_ena is broken when multiple VLANs are active
Just remove vlan_ena and use num_vlan instead.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the gate that prevents the OROM and netlist info from being
populated. The NVM now has the appropriate section for software to
reference the versioning info.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver is able to override the firmware when it comes to supporting
a more lenient link mode. This feature was limited to E810 devices. It
is now extended to E82X devices.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are times when the driver shouldn't return an error when the Get
PHY abilities AQ command (0x0600) returns an error. Instead the driver
should log that the error occurred and continue on. This allows the
driver to load even though the AQ command failed. The user can then
later determine the reason for the failure and correct it.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_flow_add_prof_sync(), struct ice_flow_prof_params has recently
grown in size hogging stack space when allocated there. Hogging stack
space should be avoided. Change allocation to be on the heap when needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Harikumar Bokkena <harikumarx.bokkena@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
When performing a flash update via devlink, device drivers may inform
user space of status updates via
devlink_flash_update_(begin|end|timeout|status)_notify functions.
It is expected that drivers do not send any status notifications unless
they send a begin and end message. If a driver sends a status
notification without sending the appropriate end notification upon
finishing (regardless of success or failure), the current implementation
of the devlink userspace program can get stuck endlessly waiting for the
end notification that will never come.
The current ice driver implementation may send such a status message
without the appropriate end notification in rare cases.
Fixing the ice driver is relatively simple: we just need to send the
begin_notify at the start of the function and always send an end_notify
no matter how the function exits.
Rather than assuming driver authors will always get this right in the
future, lets just fix the API so that it is not possible to get wrong.
Make devlink_flash_update_begin_notify and
devlink_flash_update_end_notify static, and call them in devlink.c core
code. Always send the begin_notify just before calling the driver's
flash_update routine. Always send the end_notify just after the routine
returns regardless of success or failure.
Doing this makes the status notification easier to use from the driver,
as it no longer needs to worry about catching failures and cleaning up
by calling devlink_flash_update_end_notify. It is now no longer possible
to do the wrong thing in this regard. We also save a couple of lines of
code in each driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers which implement the devlink flash update support, with the
exception of netdevsim, use either request_firmware or
request_firmware_direct to locate the firmware file. Rather than having
each driver do this separately as part of its .flash_update
implementation, perform the request_firmware within net/core/devlink.c
Replace the file_name parameter in the struct devlink_flash_update_params
with a pointer to the fw object.
Use request_firmware rather than request_firmware_direct. Although most
Linux distributions today do not have the fallback mechanism
implemented, only about half the drivers used the _direct request, as
compared to the generic request_firmware. In the event that
a distribution does support the fallback mechanism, the devlink flash
update ought to be able to use it to provide the firmware contents. For
distributions which do not support the fallback userspace mechanism,
there should be essentially no difference between request_firmware and
request_firmware_direct.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:
drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.
Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.
In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.
If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.
This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.
Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.
Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.
Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.
Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee0 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ice to the new infra, use share port tables.
Leave a tiny bit more error checking in place than usual,
because this driver really does quite a bit of magic.
We need to calculate the number of VxLAN and GENEVE entries
the firmware has reserved.
Thanks to the conversion the driver will no longer sleep in
an atomic section.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ice_get_open_tunnel_port() is always passed TNL_ALL
as the second parameter.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the recently added DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK
parameter in the ice flash update handler. Convert the overwrite mask
bitfield into the appropriate preservation level used by the firmware
when updating.
Because there is no equivalent preservation level for overwriting only
identifiers, this combination is rejected by the driver as not supported
with an appropriate extended ACK message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly
release memory associated with the VSI rings. If we had used devres
allocations for the rings, this would be ok. However, we use kzalloc and
kfree_rcu for these ring structures.
Using the correct label to cleanup the rings during ice_vsi_setup
highlights an issue in the ice_vsi_clear_rings function: it can leave
behind stale ring pointers in the q_vectors structure.
When releasing rings, we must also ensure that no q_vector associated
with the VSI will point to this ring again. To resolve this, loop over
all q_vectors and release their ring mapping. Because we are about to
free all rings, no q_vector should remain pointing to any of the rings
in this VSI.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.
This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.
An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs
Fixes: 3a858ba392 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It appears that the ice_suspend flow is missing a call to pci_save_state
and this is triggering the message "State of device not saved by
ice_suspend" and a call trace. Fix it.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.
v4:
Add missing kerneldoc for ICE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for dma_need_sync earlier to increase
performance. xsk_buff_dma_sync_for_cpu() takes an xdp_buff as
parameter and from that the xsk_buff_pool reference is dug out. Perf
shows that this dereference causes a lot of cache misses. But as the
buffer pool is now sent down to the driver at zero-copy initialization
time, we might as well use this pointer directly, instead of going via
the xsk_buff and we can do so already in xsk_buff_dma_sync_for_cpu()
instead of in xp_dma_sync_for_cpu. This gets rid of these cache
misses.
Throughput increases with 3% for the xdpsock l2fwd sample application
on my machine.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-11-git-send-email-magnus.karlsson@intel.com
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a collection of minor fixes including typos, white space, and
style. No functional changes.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The profile ID map lock should be held till the caller completes
all references of that profile entries.
The current code releases the lock right after the match search.
This caused a driver issue when the profile map entries were
referenced after it was freed in other thread after the lock was
released earlier.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the PTYPE lookup table to reflect values that can be set by the
hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Disable VLAN pruning when entering promiscuous mode, and re-enable it
when exiting.
Without this VLAN-over-bridge topologies created on the device won't be
functional unless rx-vlan-filter is explicitly disabled with ethtool.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the ice_init_hw_tbls, if the devm_kcalloc for es->written fails, catch
that error and bail out gracefully, instead of continuing with a NULL
pointer.
Fixes: 32d63fa1e9 ("ice: Initialize DDP package structures")
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of commit 248de22e63 ("i40e/i40evf: Account for frags
split over multiple descriptors in check linearize")
As part of testing workloads (read/write) using larger IO size (128K)
tx_timeout is observed and whenever it happens, it was due to
tx_linearize.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently VFs are only allowed to get 16, 4, and 1 queue pair by
default, which require 17, 5, and 2 MSI-X vectors respectively. This
is because each VF needs a MSI-X per data queue and a MSI-X for its
other interrupt. The calculation is based on the number of VFs created,
MSI-X available, and queue pairs available at the time of VF creation.
Unfortunately the values above exclude 2 queue pairs when only 3 MSI-X
are available to each VF based on resource constraints. The current
calculation would default to 2 MSI-X and 1 queue pair. This is a waste
of resources, so fix this by allowing 2 queue pairs per VF when there
are between 2 and 5 MSI-X available per VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This fix has been added to address memory leak issues resulting from
triggering a sudden driver reset which does not allow us to follow our
normal removal flows for SW XLT entries for advanced features.
- Adding call to destroy flow profile locks when clearing SW XLT tables.
- Extraction sequence entries were not correctly cleared previously
which could cause ownership conflicts for repeated reset-replay calls.
Fixes: 31ad4e4ee1 ("ice: Allocate flow profile")
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Display and count some useful hot-path statistics. The usefulness is as
follows:
- tx_restart: use to determine if the transmit ring size is too small or
if the transmit interrupt rate is too low.
- rx_gro_dropped: use to count drops from GRO layer, which previously were
completely uncounted when occurring.
- tx_busy: use to determine when the driver is miscounting number of
descriptors needed for an skb.
- tx_timeout: as our other drivers, count the number of times we've reset
due to timeout because the kernel only prints a warning once per netdev.
Several of these were already counted but not displayed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The page reuse statistic wasn't even being displayed to the user, even
though the driver counted it. Don't waste the struct space and hot-path
cycles since the driver doesn't display it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replacing flow profile locks with RSS profile locks in the function to
remove all RSS rules for a given VSI. This is to align the locks used
for RSS rule addition to VSI and removal during VSI teardown to avoid
a race condition owing to several iterations of the above operations.
In function to get RSS rules for given VSI and protocol header replacing
the pointer reference of the RSS entry with a copy of hash value to
ensure thread safety.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
set_rss_lut can fail due to incorrect vsi_id mask. vsi_id is 10 bit
but mask was 0x1FF whereas it should be 0x3FF.
For vsi_num >= 512, FW set_rss_lut can fail with return code
EACCESS (VSI ownership issue) because software was providing
incorrect vsi_num (dropping 10th bit due to incorrect mask) for
set_rss_lut admin command
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The grst_delay variable in ice_check_reset contains the maximum time
(in 100 msec units) that the driver will wait for a reset event to
transition to the Device Active state. The value is the sum of three
separate components:
1) The maximum time it may take for the firmware to process its
outstanding command before handling the reset request.
2) The value in RSTCTL.GRSTDEL (the delay firmware inserts between first
seeing the driver reset request and the actual hardware assertion).
3) The maximum expected reset processing time in hardware.
Referring to this total time as "grst_delay" is misleading and
potentially confusing to someone checking the code and cross-referencing
the hardware specification.
Fix this by renaming the variable to "grst_timeout", which is more
descriptive of its actual use.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/intel/ice/ice_main.c:4214:12: warning:
'ice_resume' defined but not used [-Wunused-function]
4214 | static int ice_resume(struct device *dev)
| ^~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_main.c:4150:12: warning:
'ice_suspend' defined but not used [-Wunused-function]
4150 | static int ice_suspend(struct device *dev)
| ^~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Depending on PAGE_SIZE, the following unused parameter warning can be
reported:
drivers/net/ethernet/intel/ice/ice_txrx.c: In function ‘ice_rx_frame_truesize’:
drivers/net/ethernet/intel/ice/ice_txrx.c:513:21: warning: unused parameter ‘size’ [-Wunused-parameter]
unsigned int size)
The 'size' variable is used only when PAGE_SIZE >= 8192. Add __maybe_unused
to remove the warning.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
For the FW logging info AQ command, we currently set the ICE_AQ_FLAG_RD
in order to work around a FW issue. This issue has been fixed so remove the
workaround.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The scope of the macro local variable 'i' can be reduced. Do so to avoid
static analysis tools from complaining.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of ice_setup_pf_sw() a PF VSI is setup; release the VSI in case of
failure.
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the PF VSI's context parameters are left in a bad state when
going into safe mode. This is causing VLAN traffic to not pass. Fix this
by configuring the PF VSI to allow all VLAN tagged traffic.
Also, remove redundant comment explaining the safe mode flow in
ice_probe().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This is a port of i40e commit 705639572e ("i40e: need_wakeup flag might
not be set for Tx").
Quoting the original commit message:
"The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an interrupt
since interrupts are disabled in the napi poll loop) between the time we
stopped processing the Tx completions and interrupts are enabled again.
In this case, the need_wakeup flag will have been cleared at the end of
the Tx completion processing as we believe we will get an interrupt from
the outstanding completion at a later point in time. But if this
completion interrupt occurs before interrupts are enable, we lose it and
should at that point really have set the need_wakeup flag since there
are no more outstanding completions that can generate an interrupt to
continue the processing. When this happens, user space will see a Tx
queue need_wakeup of 0 and skip issuing a syscall, which means will
never get into the Tx processing again and we have a deadlock."
As a result, packet processing stops. This patch introduces a fix for
this issue, by always setting the need_wakeup flag at the end of an
interrupt processing. This ensures that the deadlock will not happen.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Distribute the Tx queues evenly across all queue groups. This will
help the queues to get more equal sharing among the queues when all
are in use.
In the previous algorithm, the next queue group node will be picked up
only after the previous one filled with max children.
For example: if VSI is configured with 9 queues, the first 8 queues
will be assigned to queue group 1 and the 9th queue will be assigned to
queue group 2.
The 2 queue groups split the bandwidth between them equally (50:50).
The first queue group node will share the 50% bandwidth with all of
its children (8 queues). And the second queue group node will share
the entire 50% bandwidth with its only children.
The new algorithm will fix this issue.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
By default the queues are configured in legacy mode. The default
BW settings for legacy/advanced modes are different. The existing
code was using the advanced mode default value of 1 which was
incorrect. This caused the unbalanced BW sharing among siblings.
The recommended default value is applied.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask bits before accessing the profile type field.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a user sets the value of the TX or RX descriptors to some non-default
value using 'ethtool -G' then we need to not overwrite the values when
we rebuild the VSI. The VSI rebuild could happen as a result of a user
setting the number of queues via the 'ethtool -L' command. Fix this by
checking to see if the value we have stored is non-zero and if it is
then don't change the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Return ICE_ERR_DOES_NOT_EXIST return code if admin command error code is
ICE_AQ_RC_ENOENT (not exist). ice_aq_sw_rules is used when switch
rule is getting added/deleted/updated. In case of delete/update
switch rule, admin command can return ICE_AQ_RC_ENOENT error code
if such rule does not exist, hence return ICE_ERR_DOES_NOT_EXIST error
code from ice_aq_sw_rule, so that caller of this function can decide
how to handle ICE_ERR_DOES_NOT_EXIST.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Signed-off-by: Nick Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the driver experiences a link event (especially link up)
there can be multiple events generated. Some of these are
link fault and still have a state of DOWN set. The problem
happens when the link comes UP during the PF driver handling
one of the LINK DOWN events. The status of the link is updated
and is now seen as UP, so when the actual LINK UP event comes,
the port information has already been updated to be seen as UP,
even though none of the UP activities have been completed.
After the link information has been updated in the link
handler and evaluated for MEDIA PRESENT, if the state
of the link has been changed to UP, treat the DOWN event
as an UP event since the link is now UP.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After a GLOBR, the link was broken so that a link
up situation was being seen as a link down.
The problem was that the rebuild process was updating
the port_info link status without doing any of the
other things that need to be done when link changes.
This was causing the port_info struct to have current
"UP" information so that any further UP interrupts
were skipped as redundant.
The rebuild flow should *not* be updating the port_info
struct link information, so eliminate this and leave
it to the link event handling code.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a bug where the LFC settings are not being preserved
through a link event. The registers in question are the ones
that are touched (and restored) when a set_local_mib AQ command
is performed.
On a link-up event, make sure that a set_local_mib is being
performed.
Move the function ice_aq_set_lldp_mib() from the DCB specific
ice_dcb.c to ice_common.c so that the driver always has access
to this AQ command.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the newly added pldmfw library to implement device flash update for
the Intel ice networking device driver. This support uses the devlink
flash update interface.
The main parts of the flash include the Option ROM, the netlist module,
and the main NVM data. The PLDM firmware file contains modules for each
of these components.
Using the pldmfw library, the provided firmware file will be scanned for
the three major components, "fw.undi" for the Option ROM, "fw.mgmt" for
the main NVM module containing the primary device firmware, and
"fw.netlist" containing the netlist module.
The flash is separated into two banks, the active bank containing the
running firmware, and the inactive bank which we use for update. Each
module is updated in a staged process. First, the inactive bank is
erased, preparing the device for update. Second, the contents of the
component are copied to the inactive portion of the flash. After all
components are updated, the driver signals the device to switch the
active bank during the next EMP reset (which would usually occur during
the next reboot).
Although the firmware AdminQ interface does report an immediate status
for each command, the NVM erase and NVM write commands receive status
asynchronously. The driver must not continue writing until previous
erase and write commands have finished. The real status of the NVM
commands is returned over the receive AdminQ. Implement a simple
interface that uses a wait queue so that the main update thread can
sleep until the completion status is reported by firmware. For erasing
the inactive banks, this can take quite a while in practice.
To help visualize the process to the devlink application and other
applications based on the devlink netlink interface, status is reported
via the devlink_flash_update_status_notify. While we do report status
after each 4k block when writing, there is no real status we can report
during erasing. We simply must wait for the complete module erasure to
finish.
With this implementation, basic flash update for the ice hardware is
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a flash update, the pending status of the update can be determined
from the device capabilities.
Read the appropriate device capability and store whether there is
a pending update awaiting a reboot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures, identifiers, and helper functions for several AdminQ
commands related to performing a firmware update for the ice hardware.
These will be used in future code for implementing the devlink
.flash_update handler.
Signed-off-by: Cudzilo, Szymon T <szymon.t.cudzilo@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends function parsing response from Discover Device
Capability AQC to check if the device supports unified NVM update flow.
Signed-off-by: Jacek Naczyk <jacek.naczyk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2020-06-25
This series contains updates to i40e driver and removes the individual
driver versions from all of the Intel wired LAN drivers.
Shiraz moves the client header so that it can easily be shared between
the i40e LAN driver and i40iw RDMA driver.
Jesse cleans up the unused defines, since they are just dead weight.
Alek reduces the unreasonably long wait time for a PF reset after reboot
by using jiffies to limit the maximum wait time for the PF reset to
succeed. Added additional logging to let the user know when the driver
transitions into recovery mode. Adds new device support for our 5 Gbps
NICs.
Todd adds a check to see if MFS is set after warm reboot and notifies
the user when MFS is set to anything lower than the default value.
Arkadiusz fixes a possible race condition, where were holding a
spin-lock while in atomic context.
v2: removed code comments that were no longer applicable in patch 2 of
the series. Also removed 'inline' from patch 4 and patch 8 of the
series. Also re-arranged code to be able to remove the forward
function declarations. Dropped patch 9 of the series, while the
author works on cleaning up the commit message.
v3: Updated patch 8 description to answer Jakub's questions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The READ_ONCE macro is used when reading rings prior to accessing the
statistics pointer. The corresponding WRITE_ONCE usage when allocating and
freeing the rings to ensure protected access was not in place. Introduce
this.
Signed-off-by: Ciara Loftus <ciara.loftus@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
When setting the PHY cfg (CQ cmd 0x0601), if the firmware responds
with an EMODE error, software will ignore the error as it simply
means that manageability (ex: BMC) is in control of the link and that
the new setting may not be applied.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The logic was missing for adding back perfect flows after flow director
filter delete. The code now adds perfect flows into the HW tables after
filter delete.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VSI is built (i.e. reset, set channels, etc.)
the coalesce settings will be preserved in most cases. However, when the
number of q_vectors are increased the settings for the new q_vectors
will be set to the driver defaults of AIM on, Rx/Tx ITR 50, and INTRL 0.
This is causing issues with how the ethtool layer gets the current
coalesce settings since it only uses q_vector 0. So, assume that the user
set the coalesce settings globally (i.e. ethtool -C eth0) and use q_vector
0's settings for all of the new q_vectors.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ceb2f00707 ("ice: Use pci_get_dsn()") changed the code to
use a new function to get the Device Serial Number. It also changed
the case of the filename for loading a package on a specific NIC
from lowercase to uppercase. Change the filename back to
lowercase since that is what we specified.
Fixes: ceb2f00707 ("ice: Use pci_get_dsn()")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, cuddle multiple lines of function signatures to be
consistent throughout the code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VF driver has the ability to request reset via VIRTCHNL_OP_RESET_VF.
This is a required step in VF driver load. Currently, the PF is only
allowing a VF to request reset using this method after the VF has
already communicated resources via VIRTCHNL_OP_GET_VF_RESOURCES.
However, this is incorrect because the VF can request reset before
requesting resources. Fix this by allowing the VF to request a reset
once it has been initialized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver prevents a user from doing
modprobe ice
ethtool -L eth0 combined 5
ip link set eth0 up
The ethtool command fails, because the driver is checking to see if the
interface is down before allowing the get_channels to proceed (even for
a set_channels).
Remove this check and allow the user to configure the interface
before bringing it up, which is a much better usability case.
Fixes: 87324e747f ("ice: Implement ethtool ops for channels")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF is modifying the VF's port VLAN on the fly when
configured via iproute. This is okay for most cases, but if the VF
already has guest VLANs configured the PF has to remove all of those
filters so only VLAN tagged traffic that matches the port VLAN will
pass. Instead of adding functionality to track which guest VLANs have
been added, just reset the VF each time port VLAN parameters are
modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As currently, we are supporting only 5 PHY_SPEEDs for phy_type_high.
Thus, we should adjust the value of ICE_PHY_TYPE_HIGH_MAX_INDEX to 5.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To allow for resets during package download, increase the timeout period
after performing a PFR. The time waited is the global config lock
timeout plus the normal PFSWR timeout.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not recognize when there is an 802.1AD VLAN
tag right after the dmac/smac (outermost VLAN tag). If any DCB map is
applied and/or DCB is enabled this is causing the hardware to insert a
VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet.
Fix this by preventing VLAN tag 0 from being added when any VLAN is
already present after dmac/smac (software offloaded) or skb (hardware
offloaded).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a UMEM is present on a queue when an interface/queue pair is being
enabled, the driver will try to prepare the Rx buffers in advance to
improve performance. However, if fill queue is shorter than HW Rx ring,
the driver will report failure after getting the last address from the
fill queue.
This still lets the driver process the packets correctly during the NAPI
poll, but leads to a constant NAPI rescheduling. Not allocating the
buffers in advance would result in a potential performance decrease.
Commit d57d76428a ("xsk: Add API to check for available entries in FQ")
provides an API that lets drivers check the number of addresses that the
fill queue holds.
Notify the user if fill queue is not long enough to prepare all buffers
before packet processing starts, and allocate the buffers during the
NAPI poll. If the fill queue size is sufficient, prepare Rx buffers in
advance.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need both rx_status and rx_error parameters, as the latter is
a subset of the former. Remove rx_error completely and check the right bit
in rx_status.
Rename rx_status to rx_status0, and rx_status_err1 to
rx_status1. This naming more closely reflects the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When writing the driver's struct ice_tlan_ctx structure, do not write the
8-bit element int_q_state with the associated internal-to-hardware field
which is 122-bits, otherwise the helper function ice_write_byte() will use
undefined behavior when setting the mask used for that write. This should
not cause any functional change and will avoid use of undefined behavior.
Also, update a comment to highlight this structure element is not written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current implementation number of XDP Tx queues is the same as
the number of transmit queues, which is not always true. This
patch changes this number to match the number of receive queues.
XDP programs are running on Rx rings, so what we actually need to
provide is the XDP Tx ring per each Rx ring so that the whole XDP
ecosystem is functional, e.g. if the result of XDP prog is XDP_TX
then you have the need to access the XDP Tx ring.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx program is loaded and packets are sent from
interface, VSI statistics are not updated. This patch adds
packets sent on Tx XDP ring to VSI ring stats.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx rings are destroyed the number of XDP Tx queues
is not changing. This patch is changing this number to 0.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if the PVID is set in the VLAN handling section of the VSI
context the driver still allows VLAN stripping to be enabled/disabled.
VLAN stripping should only be modifiable when the PVID is not set. Fix
this by preventing VLAN stripping modification when PVID is set.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are only including illegal_bytes and rx_crc_errors in the
PF netdev's rx_error counter. There are many more causes of Rx errors
that the device supports and reports via Ethtool. Accumulate all Rx
errors in the PF netdev's rx_error counter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Handle memory leaks during control queue initialization and
buffer allocation failures. The macro ICE_FREE_CQ_BUFS is modified to
re-use for this fix.
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The manage MAC write command was implemented in an overly complex way
that actually didn't work, as it wasn't symmetric to the manage MAC
read command, and was feeding bytes out of order to the firmware. Fix
the implementation by just using a simple array to represent the MAC
address when it is being written via firmware command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove is_zero_ether_add() check when setting the VF default LAN address.
This check assumed that the address had been delete and zeroed before
calling ice_vc_add_mac_addr(). Now the default LAN address will be set
to the last unicast MAC address added by the VF.
The default LAN address is reported by the PF via ndo_get_vf_config.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver had an unused define that can be removed. Found by
compiler -Werror=unused-macros check.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the remaining signed vs unsigned issues, which appear
when compiling with -Werror=sign-compare.
Many of these are because there is an external interface that is passing
an int to us (which we can't change) but that we (rightfully) store
and compare against as an unsigned in our data structures.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-22
This series contains updates to virtchnl and the ice driver.
Geert Uytterhoeven fixes a data structure alignment issue in the
virtchnl structures.
Henry adds Flow Director support which allows for the redirection on
ntuple rules over six patches. Initially Henry adds the initial
infrastructure for Flow Director, and then later adds IPv4 and IPv6
support, as well as being able to display the ntuple rules.
Bret add Accelerated Receive Flow Steering (aRFS) support which is used
to steer receive flows to a specific queue. Fixes a transmit timeout
when the VF link transitions from up/down/up because the transmit and
receive queue interrupts are not enabled as part of VF's link up. Fixed
an issue when the default VF LAN address is changed and after reset the
PF will attempt to add the new MAC, which fails because it already
exists. This causes the VF to be disabled completely until it is removed
and enabled via sysfs.
Anirudh (Ani) makes a fix where the ice driver needs to call set_mac_cfg
to enable jumbo frames, so ensure it gets called during initialization
and after reset. Fix bad register reads during a register dump in
ethtool by removing the bad registers.
Paul fixes an issue where the receive Malicious Driver Detection (MDD)
auto reset message was not being logged because it occurred after the VF
reset.
Victor adds a check for compatibility between the Dynamic Device
Personalization (DDP) package and the NIC firmware to ensure that
everything aligns.
Jesse fixes a administrative queue string call with the appropriate
error reporting variable. Also fixed the loop variables that are
comparing or assigning signed against unsigned values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The "ethtool -d" handler reads registers in the ice_regs_dump_list array
and returns read values back to the userspace.
The register offsets PFINT0_ITR* are not valid as per the specification
and reading these causes a "unable to handle kernel paging request" bug
in the driver. Remove these registers from ice_regs_dump_list.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if a unicast MAC is set via ndo_set_vf_mac, the PF driver will
set the VF's dflt_lan_addr.addr once some basic checks have passed. The
VF is then reset. During reset the PF driver will attempt to program the
VF's MAC from the dflt_lan_addr.addr field. This fails when the MAC
already exists on the PF's switch.
This is causing the VF to be completely disabled until removing/enabling
any VFs via sysfs.
Fix this by checking if the unicast MAC exists before triggering a VF
reset directly in ndo_set_vf_mac. Also, add a check if the unicast MAC
is set to the same value as before and return 0 if that is the case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the iavf is loaded and a VF link transitions from up to
down to up again a Tx timeout will be triggered. This happens because
Tx/Rx queue interrupts are only enabled when receiving the
VIRTCHNL_OP_CONFIG_MAP_IRQ message, which happens on reset or initial
iavf driver load, but not when bringing link up. This is problematic
because they are disabled on the VIRTCHNL_OP_DISABLE_QUEUES message,
which is part of bringing a VF's link down. However, they are not
enabled on the VIRTCHNL_OP_ENABLE_QUEUES message, which is part of
bringing a VF's link up.
Fix this by re-enabling the VF's Rx and Tx queue interrupts when they
were previously configured. This is done by first checking to make
sure the previous value in QINT_[R|T]QCTL.MSIX_INDX is not 0, which
is used to represent the OICR in the VF's interrupt space. If the
MSIX_INDX is non-zero then enable the interrupt by setting the
QINT_[R|T]CTL.CAUSE_ENA bit to 1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.
Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.
The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.
The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.
In the Rx path the following things can happen:
1. New aRFS entries are added to the hash table and the state is
set to ICE_ARFS_INACTIVE so the filter can be updated in HW
by the ice_service_task path.
2. aRFS entries have their Rx Queue updated if we receive a
pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
The state is set to ICE_ARFS_INACTIVE so the filter can be
updated in HW by the ice_service_task path.
3. aRFS entries marked as ICE_ARFS_TODEL are deleted
In the ice_service_task path the following things can happen:
1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
updated in HW.
and their state is updated to ICE_ARFS_ACTIVE.
2. aRFS entries are deleted from HW and their state is updated
to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option. It is specified by providing
an offset followed by a 2 byte match value. Offset is measured from the
start of the MAC address.
The following restrictions apply to flex-bytes. The specified offset must
be an even number and be smaller than 0x1fe.
Example usage:
ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 12 dst-port 13 user-def 0x10ffff action 32
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the function easier to identify as being part of the ice driver,
prepend ice to the function name.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Self-explanatory.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable status cannot be zero due to a prior check of it; remove this
check.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move filter functions to separate file.
Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.
Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Memory allocated in the ice_add_prof_id_vsig() function wasn't being
properly freed if an error occurred inside the for-loop in the function.
In particular, 'p' wasn't being freed if an error occurred before it was
added to the resource list at the end of the for-loop.
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.
The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.
Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the ice driver is setting a PHY configuration,
which causes a link drop, and then additionally it calls
for a nway_reset, which restarts auto-negotiation on the
link, which also causes a link drop. These two link
events in such close timing is causing the FW to not be
able to generate a link interrupt for the driver to
respond to.
Remove the unnecessary auto-negotiation restart from the
set pauseparams flow. Also remove error path that
would have performed an ice_down/ice_up as that is
also unnecessary.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation for contiguous TC check
is assuming that the UPs will be mapped to TCs in
a linear progressing fashion. This is obviously
not always true.
Change the check to allow for various UP2TC mapping
configurations.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.
In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement promiscuous support for VF VSIs. Behaviour of promiscuous support
is based on VF trust as well as the, introduced, vf-true-promisc flag.
A trusted VF with vf-true-promisc disabled will be the default VSI, which
means that all traffic without a matching destination MAC address in the
device's internal switch will be forwarded to this VF VSI.
A trusted VF with vf-true-promisc enabled will go into "true promiscuous
mode". This amounts to the VF receiving all ingress and egress traffic
that hits the device's internal switch.
An untrusted VF will only receive traffic destined for that VF.
The vf-true-promisc-support flag cannot be toggled while any VF is in
promiscuous mode. This flag should be set prior to loading the iavf driver
or spawning VF(s).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.
As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.
This includes both a version and the first few bytes of a hash of the
module contents.
fw.netlist -> the version information extracted from the netlist module
fw.netlist.build-> first 4 bytes of the hash of the contents, similar
to fw.mgmt.build
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove MEM_TYPE_ZERO_COPY in favor of the new MEM_TYPE_XSK_BUFF_POOL
APIs.
v4->v5: Fixed "warning: Excess function parameter 'alloc' description
in 'ice_alloc_rx_bufs_zc'" and "warning: Excess function
parameter 'xdp' description in
'ice_construct_skb_zc'". (Jakub)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20200520192103.355233-10-bjorn.topel@gmail.com
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
Intel drivers implement native AF_XDP zerocopy in separate C-files,
that have its own invocation of bpf_prog_run_xdp(). The setup of
xdp_buff is also handled in separately from normal code path.
This patch update XDP frame_sz for AF_XDP zerocopy drivers i40e, ice
and ixgbe, as the code changes needed are very similar. Introduce a
helper function xsk_umem_xdp_frame_sz() for calculating frame size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/158945347511.97035.8536753731329475655.stgit@firesoul
This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".
For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.
The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).
There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945347002.97035.328088795813704587.stgit@firesoul
Fix to return a error code from the error handling case
instead of 0, as done elsewhere in this function.
Fixes: 31ad4e4ee1 ("ice: Allocate flow profile")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a unique board identifier using "board.id" for devlink's
.info_get command.
Obtain this by reading the NVM for the PBA identification string.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The devlink .info_get callback allows the driver to report detailed
version information. The following devlink versions are reported with
this initial implementation:
"fw.mgmt" -> The version of the firmware that controls PHY, link, etc
"fw.mgmt.api" -> API version of interface exposed over the AdminQ
"fw.mgmt.build" -> Unique build id of the source for the management fw
"fw.undi" -> Version of the Option ROM containing the UEFI driver
"fw.psid.api" -> Version of the NVM image format.
"fw.bundle_id" -> Unique identifier for the combined flash image.
"fw.app.name" -> The name of the active DDP package.
"fw.app" -> The version of the active DDP package.
With this, devlink dev info can report at least as much information as
is reported by ETHTOOL_GDRVINFO.
Compare the output from ethtool vs from devlink:
$ ethtool -i ens785s0
driver: ice
version: 0.8.1-k
firmware-version: 0.80 0x80002ec0 1.2581.0
expansion-rom-version:
bus-info: 0000:3b:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial number 00-01-ab-ff-ff-ca-05-68
versions:
running:
fw.mgmt 2.1.7
fw.mgmt.api 1.5
fw.mgmt.build 0x305d955f
fw.undi 1.2581.0
fw.psid.api 0.80
fw.bundle_id 0x80002ec0
fw.app.name ICE OS Default Package
fw.app 1.3.1.0
More pieces of information can be displayed, each version is kept
separate instead of munged together, and each version has an identifier
which comes with associated documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of .get_eeprom only enables reading from the
Shadow RAM portion of the NVM contents. Implement support for reading
the entire flash contents instead of only the initial portion contained
in the Shadow RAM.
A complete dump can take several seconds, but the ETHTOOL_GEEPROM ioctl
is capable of reading only a limited portion at a time by specifying the
offset and length to read.
In order to perform the reads directly, several functions are made non
static. Additionally, the unused ice_read_sr_buf_aq and ice_read_sr_buf
functions are removed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When reading from the NVM using a flat address, it is useful to know the
upper bound on the size of the flash contents. This value is not stored
within the NVM.
We can determine the size by performing a bisection between upper and
lower bounds. It is known that the size cannot exceed 16 MB (offset of
0xFFFFFF).
Use a while loop to bisect the upper and lower bounds by reading one
byte at a time. On a failed read, lower the maximum bound. On
a successful read, increase the lower bound.
Save this as the flash_size in the ice_nvm_info structure that contains
data related to the NVM.
The size will be used in a future patch for implementing full NVM read
via ethtool's GEEPROM command.
The maximum possible size for the flash is bounded by the size limit for
the NVM AdminQ commands. Add a new macro, ICE_AQC_NVM_MAX_OFFSET, which
can be used to represent this upper bound.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM version and Option ROM version information is stored within the
struct ice_nvm_ver_info structure. The data for the NVM is stored as
a 2byte value with the major and minor versions each using one byte from
the field. The Option ROM is stored as a 4byte value that contains
a major, build, and patch number.
Modify the code to immediately extract the version values and store them
in a new struct ice_orom_info. Remove the now unnecessary
ice_get_nvm_version function.
Update ice_ethtool.c to use the new fields directly from the structured
data.
This reduces complexity of the code that prints these versions in
ice_ethtool.c
Update the macro definitions and variable names to use the term "orom"
instead of "oem" for the Option ROM version. This helps increase the
clarity of the Option ROM version code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:
1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
boundaries. The sectors are also 4Kb in size.
Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.
This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.
Use this new function as the implementation of ice_read_sr_word_aq.
The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_read_sr_aq function returns words in the Little Endian format.
Remove the need for __force and typecasting by using a local variable in
the ice_read_sr_word_aq function.
Additionally clarify explicitly that the ice_read_sr_aq function takes
storage for __le16 values instead of using u16.
Being explicit about the endianness of this data helps when using tools
like sparse to catch endian-related issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function comment for ice_get_nvm_version indicated that the ver_hi
and ver_lo values were 16 bits. In fact, they are only uint8_t values,
meaning that they have a maximum size of 8 bits. Fix the comment to
match the correct size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable name 'type' is not very descriptive. Replace instances of
those with a variable name that is more descriptive or replace it if not
needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using ENOTSUPP almost always results in some bizarre error message to
be printed in userspace. This is likely because ENOTSUPP was defined for
the NFS protocol (as per a comment in include/linux/errno.h). Use
EOPNOTSUPP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ed5a3f664c ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.
Fixes: ed5a3f664c ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
checkpatch complains "CHECK:DEPRECATED_API: Deprecated use of 'strlcpy',
prefer 'stracpy or strscpy' instead"; use strscpy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VLAN pruning is not always being set correctly due to a previous change
that set Tx antispoof off. ice_vsi_is_vlan_pruning_ena() currently checks
for both Tx antispoof and Rx pruning. The expectation for this function is
to only check Rx pruning so fix the check.
Fixes: cd6d6b8331 ("ice: Fix VF spoofchk")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching from SW DCB to FW DCB it is necessary
to renegotiate DCBx so that the FW agent can have up
to date information about the DCB settings of the link
partner.
Perform an autoneg restart on the link when activating
FW DCB.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While testing DCB for a corner case in which mode is switched from IEEE to
CEE and pfc_ena bitmask unchanged then DCBX mode doesn't get updated.
This is happening because the function ice_dcb_get_mode() is called
in a "no change detected block" instead of "change detected block".
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the "Link detected" field is not shown when the device goes
into safe mode. This is because the safe mode Ethtool ops does not set the
get_link function. Fix this by setting the safe mode Ethtool op get_link
function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:
pci_disable_msix()
free_msi_irqs()
...
BUG_ON(irq_has_action(entry->irq + i));
...
To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.
[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.
[2] Call ice_free_vfs() before disabling the service task.
[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.
Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.
Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when the device runs out of MSI-X interrupts a cryptic and
unhelpful message is printed. This will cause confusion when hitting this
case. Fix this by clearing up the error message for both SR-IOV and non
SR-IOV use cases.
Also, make a few minor changes to increase clarity of variables.
1. Change per VF MSI-X and queue pair variables in the PF structure.
2. Use ICE_NONQ_VECS_VF when determining pf->num_msix_per_vf instead of
the magic number "1". This vector is reserved for the OICR.
All of the resource tracking functions were moved to avoid adding
any forward declaration function prototypes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unlike the XL710 series, 800-series hardware can allocate more than 4
MSI-X vectors per VF. This patch enables that functionality. We
dynamically allocate vectors and queues depending on how many VFs are
enabled. Allocating the maximum number of VFs replicates XL710
behavior with 4 queues and 4 vectors. But allocating a smaller number
of VFs will give you 16 queues and 16 vectors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sergei Shtylyov pointed out that two instances of parenthesis are not
needed, so remove them.
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
The pci_get_dsn() function will perform two pci_read_config_dword calls
to read the lower and upper config dwords. It bitwise ORs them into
a u64 value. Instead of using put_unaligned_le32 to convert the value to
LE32 format, just use the %016llX printf specifier. This will print the
u64 correct, putting the most significant byte of the value first. Since
pci_get_dsn() correctly orders the two dwords into a u64, this should
produce equivalent results in less code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported parameters.
As a side effect of these changes the info message about
the bad parameter will no longer be printed. We also
always reject the tx_coalesce_usecs_high param, even
if the target queue pair does not have a TX queue.
Error code changes from EINVAL to EOPNOTSUPP.
v2: allow adaptive TX
v3: adjust commit message for new error code and member name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product's name has changed; update the macro identifier accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add E823 device ids and convert conditional expressions to a more
appropriate switch statement.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for device id 0x159b.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were several strings found without line feeds, fix
them by adding a line feed, as is typical. Without this
lotsofmessagescanbejumbledtogether.
This patch has known checkpatch warnings from long lines
for the NL_* messages, because checkpatch doesn't know
how to ignore them.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase the maximum time that the driver will wait for a PF reset from
200 milliseconds to 300 milliseconds, to account for possibility of
a slightly longer than expected PF reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for a new AF_XDP feature that has already been introduced in
upstreamed Intel NIC drivers. If a user space application signals that
it might sleep using the new bind flag XDP_USE_NEED_WAKEUP, the driver
will then set this flag if it has no more buffers on the NIC Rx ring and
yield to the application. For Tx, it will set the flag if it has no
outstanding Tx completion interrupts and return to the application.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lldpad is using the value reported in the DCB config for
max_tc as the max allowed number of TCs, not the current
max. ICE driver was reporting it as current maximum TC.
Change DCB_NL function to report maximum TC allowed by
this device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to detect if DCB is in IEEE or CEE mode. Without this the code
will always report as IEEE mode which is incorrect and confuses the
user.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Couple of DCBNL ops are required for configuring ETS in SW DCB CEE mode. If
these functions are not added, it'll break the CEE functionality.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when the PF reduces its number of channels via ethtool and
then VFs are created there may be stale data for some of the Rx queues
belonging to VFs. This happens when a VF reuses an Rx queue that was
previously used by the PF. Specifically, the QRXFLXP_CNTXT register
will have incorrect values. Fix this by always clearing the relevant
values in the QRXFLXP_CNTXT register for VF queues.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Order intermediate VSIG list correct in order to correctly match existing
VSIG lists.
When overriding pre-existing TCAM entries, properly delete the existing
entry and remove it from the change/update list.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.
Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().
Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.
Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.
To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Validate the inputs for SW DCB config received either via lldptool or pcap
file. And don't apply DCB for bad bandwidth inputs. Without this patch, any
config having bad inputs will cause the loss of link making PF unusable
even after driver reload. Recoverable only via system reboot.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configuration/command below is failing when the VF in the xml
file is already bound to the host iavf driver.
pci_0000_af_0_0.xml:
<interface type='hostdev' managed='yes'>
<source>
<address type='pci' domain='0x0000' bus='0xaf' slot='0x0' function='0x0'/>
</source>
<mac address='00🇩🇪ad:00:11:01'/>
</interface>
> virsh attach-device domain_name pci_0000_af_0_0.xml
error: Failed to attach device from pci_0000_af_0_0.xml
error: Cannot set interface MAC/vlanid to 00🇩🇪ad:00:11:01/0 for
ifname ens1f1 vf 0: Device or resource busy
This is failing because the VF has not been completely removed/reset
after being unbound (via the virsh command above) from the host iavf
driver and ice_set_vf_mac() checks if the VF is disabled before waiting
for the reset to finish.
Fix this by waiting for the VF remove/reset process to happen before
checking if the VF is disabled. Also, since many functions for VF
administration on the PF were more or less calling the same 3 functions
(ice_wait_on_vf_reset(), ice_is_vf_disabled(), and ice_check_vf_init())
move these into the helper function ice_check_vf_ready_for_cfg(). Then
call this function in any flow that attempts to configure/query a VF
from the PF.
Lastly, increase the maximum wait time in ice_wait_on_vf_reset() to
800ms, and modify/add the #define(s) that determine the wait time.
This was done for robustness because in rare/stress cases VF removal can
take a max of ~800ms and previously the wait was a max of ~300ms.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.
If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if a user sets an odd [tx|rx]-usecs value through ethtool,
the request is denied because the hardware is set to have an ITR
granularity of 2us. This caused poor customer experience. Fix this by
aligning to a register allowed value, which results in rounding down.
Also, print a once per ring container type message to be clear about
our intentions.
Also, change the ITR_TO_REG define to be the bitwise and of the ITR
setting and the ICE_ITR_MASK. This makes the purpose of ITR_TO_REG more
obvious.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject says it all.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0290bd291c ("netdev: pass the stuck queue to the timeout handler")
introduced a new argument to the function but missed adding the description
of the argument to the function header comment. Add it now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiling with gcc-9.2.1 with W=1 points out warnings about the improper
function parameter list. Fix it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.
There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vc_ena_qs_msg() we are incorrectly validating the
virtchnl queue select bitmaps. The virtchnl_queue_select rx_queues and
tx_queue bitmap is being compared against ICE_MAX_BASE_QS_PER_VF, but
the problem is that these bitmaps can have a value greater than
ICE_MAX_BASE_QS_PER_VF. Fix this by comparing the bitmaps against
BIT(ICE_MAX_BASE_QS_PER_VF).
Also, add the function ice_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.
Arkady Gilinksky's patch on the intel-wired-lan mailing list
("i40e/iavf: Fix msg interface between VF and PF") made me
aware of this issue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF driver sends the PF a request to disable Rx queues
we will disable them one at a time, even if the VF driver sent us a
batch of queues to disable. This is causing issues where the Rx queue
disable times out with LFC enabled. This can be improved by detecting
when the VF is trying to disable all of its queues.
Also remove the variable num_qs_ena from the ice_vf structure as it was
only used to see if there were no Rx and no Tx queues active. Instead
add a function that checks if both the vf->rxq_ena and vf->txq_ena
bitmaps are empty.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vsi_get_qs() we set the mapping_mode for Tx and Rx to
vsi->[tx|rx]_mapping_mode, but the problem is vsi->[tx|rx]_mapping_mode
have not been set yet. This was working because ICE_VSI_MAP_CONTIG is
defined to 0. Fix this by being explicit with our mapping mode by
initializing the Tx and Rx structure's mapping_mode to
ICE_VSI_MAP_CONTIG and then setting the vsi->[tx|rx]_mapping_mode to the
[tx|rx]_qs_cfg.mapping_mode values.
Also, only assign the vsi->[tx|rx]_mapping_mode when the queues are
successfully mapped to the VSI. With this change there was no longer a
need to initialize the ret variable to 0 so remove that.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.
1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.
In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.
Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.
This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.
Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF can see other's broadcast and multicast traffic because
it always has a VLAN filter for VLAN 0. Fix this by removing/adding the
VF's VLAN 0 filter when a port VLAN is added/removed respectively.
This required a few changes.
1. Move where we add VLAN 0 by default for the VF into
ice_alloc_vsi_res() because this is when we determine if a port VLAN is
present for load and reset.
2. Moved where we kill the old port VLAN filter in
ice_set_vf_port_vlan() to the very end of the function because it allows
us to save the old port VLAN configuration upon any failure case.
3. During adding/removing of a port VLAN via ice_set_vf_port_vlan() we
also need to remove/add the VLAN 0 filter rule respectively.
4. Improve log messages.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when configuring a port VLAN for a VF we are only shifting the
QoS bits by 12. This is incorrect. Fix this by getting rid of the ICE
specific VLAN defines and use the kernel VLAN defines instead.
Also, don't assign a value to vlanprio until the VLAN ID and QoS
parameters have been validated.
Also, there are many places we do (le16_to_cpu(vsi->info.pvid) &
VLAN_VID_MASK). Instead do (vf->port_vlan_info & VLAN_VID_MASK) because
we always save what's stored in vsi->info.pvid to vf->port_vlan_info in
the CPU's endianness.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for vf->link_up is incorrect because this field is only valid if
vf->link_forced is true. Fix this by adding the helper ice_is_vf_link_up()
to determine if the VF's link is up.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_vsi_manage_pvid() calls
ice_vsi_[set|kill]_pvid_fill_ctxt() when enabling/disabling a port VLAN
on a VSI respectively. These two functions have some duplication so just
move their unique pieces inline in ice_vsi_manage_pvid() and then the
duplicate code can be reused for both the enabling/disabling paths.
Before this patch the info.pvid field was not being written
correctly via ice_vsi_kill_pvid_fill_ctxt() so it was being hard coded
to 0 in ice_set_vf_port_vlan(). Fix this by setting the info.pvid field
to 0 before calling ice_vsi_update() in ice_vsi_manage_pvid().
We currently use vf->port_vlan_id to keep track of the port VLAN
ID and QoS, which is a bit misleading. Fix this by renaming it to
vf->port_vlan_info. Also change the name of the argument for
ice_vsi_manage_pvid() from vid to pvid_info.
In ice_vsi_manage_pvid() only save the fields that were modified
in the VSI properties structure on success instead of the entire thing.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.
Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the correct netif_msg_[tx,rx]_error() function to determine whether to
print the MDD event type.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove local variable num_q_vectors and use vsi->num_q_vectors instead
2. Remove local variable pf and pass vsi->back to ice_pf_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 1f45ebe0d8 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.
Fixes: 1f45ebe0d8 ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing. Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to 0.8.2-k
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide support to change or retrieve RSS hash options for a flow type.
The supported flow-types are: tcp4, tcp6, udp4, udp6, sctp4, sctp6.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set configuration for hardware RSS tables for VFs.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to optimize TCAM entries and reduce table resource usage by
searching for profiles that can be reused. Provide resource cleanup
of both hardware and software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Write the hardware tables based on the populated software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the TCAM entry with the profile data and the VSI group in the
respective SW structures. This will be subsequently used to write out
the tables to hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create an extraction sequence based on the packet header protocols to be
programmed and allocate a flow profile for the extraction sequence.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the driver to write the filtering hardware tables to allow for
changing of RSS rules. Upon loading of DDP package, a minimal configuration
should be written to hardware.
Introduce and initialize structures for storing configuration and make
the top level calls to configure the RSS tables to initial values. A packet
segment will be created but nothing is written to hardware yet.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable xmit_done is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd291c
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel ice driver to remove a redundant loop to find
stopped queue.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Coverity reports some of the calls to xdp_rxq_info_reg() as potential
issues, because the driver does not check its return value. However,
those calls are wrapped with "if (!xdp_rxq_info_is_reg(&ring->xdp_rxq))"
and this check alone is enough to be sure that the function will never
fail.
All possible states of xdp_rxq_info are:
- NEW,
- REGISTERED,
- UNREGISTERED,
- UNUSED.
The driver won't mark a queue as UNUSED under no circumstance, so the
return value can be ignored safely.
Add comments for Coverity right above calls to xdp_rxq_info_reg() to
suppress the warnings.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.
To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).
While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Coverity reports an error that is not really an error; suppress it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following the changes of commit 12299132b3 ("net: ethernet: intel: Demote
MTU change prints to debug"), change the MTU change message to netdev_dbg()
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when there are SR-IOV VF(s) and the user does "ip link show <pf
interface>" the VF unicast MAC addresses all show 00:00:00:00:00:00
if the unicast MAC was set via VIRTCHNL (i.e. not administratively set
by the host PF).
This is misleading to the host administrator. Fix this by setting the
VF's dflt_lan_addr.addr when the VF's unicast MAC address is
configured via VIRTCHNL. There are a couple cases where we don't allow
the dflt_lan_addr.addr field to be written. First, If the VF's
pf_set_mac field is true and the VF is not trusted, then we don't allow
the dflt_lan_addr.addr to be modified. Second, if the
dflt_lan_addr.addr has already been set (i.e. via VIRTCHNL).
Also a small refactor was done to separate the flow for add and delete
MAC addresses in order to simplify the logic for error conditions
and set/clear the VF's dflt_lan_addr.addr field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the flow for ice_set_vf_link_state() is not configuring link
the same as all other VF link configuration flows. Fix this by only
setting the necessary VF members in ice_set_vf_link_state() and then
call ice_vc_notify_link_state() to actually configure link for the
VF. This made ice_set_pfe_link_forced() unnecessary, so it was
deleted. Also, this commonizes the link flows for the VF to all call
ice_vc_notify_link_state().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove Rx flex descriptor metadata and flag programming; per specification
these registers cannot be written to as they are read only.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for all unused parameters, if ethtool sent one of them,
print info about that and return error.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After each rebuild driver deallocates q_vectors, so the interrupt
throttle rate (ITR) settings get lost.
Create a function to save and restore ITR for each queue. If a user
increases the number of queues, restore all the previous queue
settings for each existing queue, and the additional queues will
get the default setting.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the user sets itr_setting to zero from ethtool -C, the driver changes
this value to default in ice_cfg_itr (for example after changing ring
param). Remove code that sets default value in ice_cfg_itr and move it to
place where the driver allocates q_vectors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.
There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.
Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many things wrong with the function
ice_set_vf_spoofchk().
1. The VSI being modified is the PF VSI, not the VF VSI.
2. We are enabling Rx VLAN pruning instead of Tx VLAN anti-spoof.
3. The spoofchk setting for each VF is not initialized correctly
or re-initialized correctly on reset.
To fix [1] we need to make sure we are modifying the VF VSI.
This is done by using the vf->lan_vsi_idx to index into the PF's
VSI array.
To fix [2] replace setting Rx VLAN pruning in ice_set_vf_spoofchk()
with setting Tx VLAN anti-spoof.
To Fix [3] we need to make sure the initial VSI settings match what
is done in ice_set_vf_spoofchk() for spoofchk=on. Also make sure
this also works for VF reset. This was done by modifying ice_vsi_init()
to account for the current spoofchk state of the VF VSI.
Because of these changes, Tx VLAN anti-spoof needs to be removed
from ice_cfg_vlan_pruning(). This is okay for the VF because this
is now controlled from the admin enabling/disabling spoofchk. For the
PF, Tx VLAN anti-spoof should not be set. This change requires us to
call ice_set_vf_spoofchk() when configuring promiscuous mode for
the VF which requires ice_set_vf_spoofchk() to move in order to prevent
a forward declaration prototype.
Also, add VLAN 0 by default when allocating a VF since the PF is unaware
if the guest OS is running the 8021q module. Without this, MDD events will
trigger on untagged traffic because spoofcheck is enabled by default. Due
to this change, ignore add/delete messages for VLAN 0 from VIRTCHNL since
this is added/deleted during VF initialization/teardown respectively and
should not be modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8b ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f80 ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b16
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b16
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc40 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b16
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b16
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b8 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of xsk_umem_discard_addr to xsk_umem_release_addr to
better reflect the new naming of the AF_XDP queue manipulation
functions. As this functions is used by drivers implementing support
for AF_XDP zero-copy, it requires a name change to these drivers. The
function xsk_umem_release_addr_rq has also changed name in the same
fashion.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/1576759171-28550-10-git-send-email-magnus.karlsson@intel.com
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Update FW API minor version to align to current value advertised
by FW in new NVM images.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in ice_sched_cleanup_all checks whether the port info is NULL
prior to calling ice_sched_clear_port. However, ice_sched_clear_port
already checks whether port info is non-NULL.
More importantly, it also checks whether the port structure has been
initialized by checking its port_state field as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the
ip -s link show dev <PF> command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtchannel interface was repeating a lot of strings
and wasting storage space in the kernel. There was also
inconsistent messages for the same thing. Consolidate all
those messages and bit checks into a couple of helper functions.
Also, reduce stack space usage by simplifying getting the pointer
to the pf using a helper.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.
Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_clear_vsi_promisc() detects if the VLAN ID sent is not 0
and sets the recipe_id to ICE_SW_LKUP_PROMISC_VLAN in that case and
ICE_SW_LKUP_PROMISC if the VLAN_ID is 0. However this doesn't allow VLAN
0 promiscuous rules to be removed, but they can be added. Fix this by
checking if the promisc_mask contains ICE_PROMISC_VLAN_RX or
ICE_PROMISC_VLAN_TX. This change was made to match what is being done
for ice_set_vsi_promisc().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when adding/deleting vlans in ice_vc_process_vlan_msg()
we are calling ice_vsi_manage_vlan_stripping() to enable/disable
when adding and deleting a VLAN respectively. This is wrong
because adding/deleting VLANs has nothing to do with configuring
VLAN stripping. VLAN stripping is configured through the
following VIRTCHNL operations:
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Unfortunately we can't just remove this because then stripping
will never be configured on VF initialization. Fix this by
adding a new function that initializes (disables/enables) VLAN
stripping for the VF based on the device supported capabilities.
This allows us to remove the call to
ice_vsi_manage_vlan_stripping() in ice_vc_process_vlan_msg().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the host disables VLAN offloads on the VF by
not setting the VIRTCHNL_VF_OFFLOAD_VLAN capability bit
we will still honor VF VLAN configuration messages over
VIRTCHNL. These messages (i.e. enable/disable VLAN stripping
and VLAN filtering) should be blocked when the feature
is not supported. Fix that by adding a helper function to
determine if the VF is allowed to do VLAN operations based
on the host's VF configuration.
Also, mirror the VF communicated capabilities in the host's
VF configuration.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware always returns 8 as the max number of supported TCs. However on
devices with more than 4 ports, the maximum number of TCs per port is
limited to 4. Check and, if necessary, correct the reporting of
capabilities for devices with more than 4 ports.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the number of functions the device has and use this number when
setting safe mode capabilities instead of calculating it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Co-developed-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is not capable of supporting SR-IOV -ENODEV is being
returned; -EOPNOTSUPP is more appropriate.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vc_dis_vf() tells iavf that it's going to perform a reset
and then performs a software reset. This is misleading based on
the function name because the VF does not get disabled. So fix
this by changing the name to ice_vc_reset_vf().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_cleanup_hdrs() has been stripped of most of its content, it only serves
as a wrapper for eth_skb_pad(). We can get rid of it altogether and
simplify the codebase.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print message to inform user of PCI link speed and width.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print message to inform user if unsupported module is inserted, and
extend the topology / configuration detection.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF_MBX_ARQLEN register array is per-PF, not global, so we should not
use the absolute VF ID as an index. Instead, use the per-PF VF ID.
This fixes an issue with VFs on PFs other than 0 not seeing reset.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without this check rebuild vsi can lead to kernel panic.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save state to correct recovery memory and I/O BARs address
after PCI bus reset. Without this after reset kernel can't
read device registers.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust ice_init_dcb to set the is_sw_lldp boolean
in the case where the FW has been detected to be
in an untenable state such that the driver
should forcibly make sure it is off.
This will ensure that the FW is in a known state.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of the driver unload flow, a PF reset is issued which may still
cause an interrupt to be generated by the device. Do not clear the
interrupt scheme until the reset is complete and there are no pending
transactions otherwise a hardware error may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCBx request non-contiguous TCs, then the driver will configure default
traffic class (TC0). This is done to prevent Tx hang since the driver
currently does not support non-contiguous TC.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Boot Configuration Section Block has been moved to the Preserved Field
Area (PFA) of NVM. Update the NVM reads that involves Boot Configuration
Section.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: Scott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.
I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.
Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.
In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.
This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;
With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.
In the followup patch the headroom/tailroom computation logic will be
introduced.
This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.
For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.
For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c. This allows us to
avoid using ifdefs to control the staticness of said functions.
Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit. Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no reason for treating DCB as first class citizen when configuring
the Tx queues and going through TCs. Reverse the logic and base the
configuration logic on rings, which is the object of interest anyway.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to 0.8.1-k
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.
Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device. If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions to initialize, parse, and clean structures representing
the DDP package.
Upon completion of package download, read and store the DDP package
contents to these structures. This configuration is used to
identify the default behavior and later used to update the HW table
entries.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the required defines, structures, and functions to enable downloading
a DDP package. Before download, checks are performed to ensure the package
is valid and compatible.
Note that package download is not yet requested by the driver as further
initialization is required to utilize the package.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_parse_caps is printing capabilities in a different way when
compared to the variable names. This makes it difficult to search for
the right strings in the debug logs. So this patch updates the
print strings to be exactly the same as the fields' name in the
structure.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should start out with a reasonable number of descriptors that
can prevent drops due to a CPU being in a power management state.
Change the default number of descriptors to 2048.
The user can always change the value at runtime. Transmit descriptor
counts are not modified because they don't need to change due to the
speed of the interface, or for power managed CPUs, but the code is
simplified to a fixed value for the transmit default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove q_left_tx and q_left_rx from the PF struct as these can be
obtained by calling ice_get_avail_txq_count and ice_get_avail_rxq_count
respectively.
The function ice_determine_q_usage is only setting num_lan_tx and
num_lan_rx in the PF structure, and these are later assigned to
vsi->alloc_txq and vsi->alloc_rxq respectively. This is an unnecessary
indirection, so remove ice_determine_q_usage and just assign values
for vsi->alloc_txq and vsi->alloc_rxq in ice_vsi_set_num_qs and use
these to set num_lan_tx and num_lan_rx respectively.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an additional boolean parameter to the ice_init_dcb
function. This boolean controls if the LLDP MIB change
events are registered for. Also, add a new function
defined ice_cfg_lldp_mib_change. The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb. The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add internal usage flag, bit 91 as described in spec.
Update width of internal queue state to 122 also as described in spec.
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes how and when the driver report link status, instead of
waiting till the call to enable queues for VF, we should report link
status earlier with opcode to get VF resources - So as to avoid reporting
erroneous information, especially when queues have not been configured.
In addition, we can also make a call to get and report link status change
after when queue is enabled, at least to report netdev or PHY link status.
This is in accordance to how link speed is being reported for PF...
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check the ICE_FLAG_DCB_CAPABLE before calling ice_init_pf_dcb.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is port of a fix from i40e commit 2ad1274fa3 ("i40e: don't
report link up for a VF who hasn't enabled queues")
Older VF drivers do not respond well to receiving a link
up notification before queues are enabled. This can cause their state
machine to think that it is safe to send traffic. This results in a Tx
hang on the VF.
Record whether the PF has actually enabled queues for the VF. When
reporting link status, always report link down if the queues aren't
enabled. In this way, the VF driver will never receive a link up
notification until after its queues are enabled.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a PFR (or bigger reset) occurs, the device clears the VF_MBX_ARQLEN
register for all VFs. But if a VFR is triggered by a VF, the device does
NOT clear this register, and the VF driver will never see the reset.
When this happens, the VF driver will eventually timeout and attempt
recovery, and usually it will be successful. But this makes resets take
a long time and there are occasional failures.
We cannot just blithely clear this register on every reset; this has
been shown to cause synchronization problems when a PFR is triggered
with a large number of VFs.
Fix this by clearing VF_MBX_ARQLEN when the reset source is not PFR.
GlobR will trigger PFR, so this test catches that occurrence as well.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has supported a transmit work limit
that was configurable from ethtool for a long time, but
there are no good use cases for having it be a variable
that can be changed at run time. In addition, this
variable was noted to be causing performance overhead
due to cache misses.
Just remove the variable and let the code use a constant
so that the functionality is maintained (a limit on the
number of transmits that will be cleaned in any one call
to the clean routines) without the cache miss.
Removes code, removes a variable, removes testing surface. Yay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a small bit of efficiency to the code by adding a
prefetch of the port_info structure in order to help
avoid a cache miss a little later on in execution.
Also add an unlikely statement to a branch which
generally will never happen in normal operation.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a simple patch to move the assignment to a local variable
closer to the site where the local variable is used. This
can help readability and also maybe performance, although the
performance enhancement is really dependent upon the compiler.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a couple of functions that don't need two arguments
passed in when the second argument already had access to
the pointer pointed to by the first.
Remove the unnecessary arguments.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_sched_get_tc_node uses pi->root without checking for NULL. Add a
check to prevent NULL pointer dereference.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places where we currently use ice_find_vsi_by_type
to get the PF (a.k.a. main) VSI. The PF VSI by definition is always
the first element in the pf->vsi array (i.e. pf->vsi[0]). So instead
add and use a new helper function ice_get_main_vsi, which just returns
pf->vsi[0].
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when vsi->req_txqs or vsi->req_rxqs are set we don't
correctly set the number of vsi->num_q_vectors. Fix this by
setting the number of queue vectors based on the max
between the vsi->alloc_txqs and vsi->alloc_rxqs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the VF adds a VLAN, VLAN pruning will be enabled for that VSI.
Also, when a VLAN gets deleted it will disable VLAN pruning even if other
VLAN(s) exists for the VF. Fix this by only disabling VLAN pruning on the
VF VSI when removing the last VF (i.e. vf->num_vlan == 0).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove code that enables DCB in initialization when SW LLDP is
activated. DCB flag is set or reset before in ice_init_pf_dcb
based on number of TCs. So there is not need to overwrite it.
Setting DCB without checking number of TCs can cause communication
problems with other cards. Host card sends packet with VLAN priority
tag, but client card doesn't strip this tag and ping doesn't work.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is currently a check in get_ndo_stats that
returns before updating stats if the VSI is down
or there are no Tx or Rx queues. This causes the
netdev to report zero stats with the netdev is down.
Remove the check so that the behavior of reporting
stats is the same as it was in IXGBE.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to ice_dis_vsi_txq() acts as the notification to the firmware
that the VF is being reset. Because of this, we need to make this call
every time we reset, regardless of whatever else we do to stop the Tx
queues.
Without this change, VF resets would fail to complete on interfaces that
were up and running.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the init path for DCB, the call to ice_init_dcb()
can return a non-zero value for either an actual
error, or due to the FW lldp engine being stopped.
We are currently treating all non-zero values only as
an indication that the FW LLDP engine is stopped.
Check for an actual error in the DCB init flow.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch limits the max TCs set by the driver to the value provided by
the firmware as per the capabilities of the device. Otherwise, hard coding
to 8 TC max would fail the device configurations with more than 4 ports.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conventionally, if the #defines/other are not needed by other header
files being included, #includes are done first followed by #defines
and other stuff. Move the #defines before the #includes to follow this
convention.
Suggested by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to inform the user if there is an issue
with the topology / configuration of the link.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the state of auto-negotiation when printing the Link
up message. Adds new text to the "NIC Link is up" line like
Autoneg: <True | False>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to recent specification versions, the field in the Queue Shutdown
AdminQ command consisting of the "driver unloading" indication is not a 4
byte field (it is byte.bit 16.0). Change it to a byte and remove the
unnecessary endian conversion.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the specification, a PF Reset must be done as part of the
driver unload flow.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
