Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes an error condition triggered when the code path which
transmits a S/G frame descriptor when the skb's headroom is not enough
for DPAA2's needs.
We are greated with a splat like the one below when a SGT structure is
recycled and that is because even though a dma_unmap is performed on the
Tx confirmation path, the unmap is not done with the proper size.
[ 714.464927] WARNING: CPU: 13 PID: 0 at drivers/iommu/io-pgtable-arm.c:281 __arm_lpae_map+0x2d4/0x30c
(...)
[ 714.465343] Call trace:
[ 714.465348] __arm_lpae_map+0x2d4/0x30c
[ 714.465353] __arm_lpae_map+0x114/0x30c
[ 714.465357] __arm_lpae_map+0x114/0x30c
[ 714.465362] __arm_lpae_map+0x114/0x30c
[ 714.465366] arm_lpae_map+0xf4/0x180
[ 714.465373] arm_smmu_map+0x4c/0xc0
[ 714.465379] __iommu_map+0x100/0x2bc
[ 714.465385] iommu_map_atomic+0x20/0x30
[ 714.465391] __iommu_dma_map+0xb0/0x110
[ 714.465397] iommu_dma_map_page+0xb8/0x120
[ 714.465404] dma_map_page_attrs+0x1a8/0x210
[ 714.465413] __dpaa2_eth_tx+0x384/0xbd0 [fsl_dpaa2_eth]
[ 714.465421] dpaa2_eth_tx+0x84/0x134 [fsl_dpaa2_eth]
[ 714.465427] dev_hard_start_xmit+0x10c/0x2b0
[ 714.465433] sch_direct_xmit+0x1a0/0x550
(...)
The dpaa2-eth driver uses an area of software annotations to transmit
necessary information from the Tx path to the Tx confirmation one. This
SWA structure has a different layout for each kind of frame that we are
dealing with: linear, S/G or XDP.
The commit referenced was incorrectly setting up the 'sgt_size' field
for the S/G type of SWA even though we are dealing with a linear skb
here.
Fixes: d70446ee1f ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201211171607.108034-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an 'of_node_put()' call when a tested device node is not available.
Fixes: 94ae899b20 ("dpaa2-mac: add PCS support through the Lynx module")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201206151339.44306-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Noticed some inconsistencies in packet statistics reporting.
This patch adds the missing Tx packet counter registers to
ethtool reporting and fixes the information strings for a
few of them.
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204171505.21389-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_OF is disabled, there is a harmless warning about
an unused variable:
enetc_pf.c: In function 'enetc_phylink_create':
enetc_pf.c:981:17: error: unused variable 'dev' [-Werror=unused-variable]
Slightly rearrange the code to pass around the of_node as a
function argument, which avoids the problem without hurting
readability.
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204120800.17193-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building FSL_DPAA_ETH the following build error shows up:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function ‘dpaa_fq_init’:
/tmp/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1135:9: error: too few arguments to function ‘xdp_rxq_info_reg’
1135 | err = xdp_rxq_info_reg(&dpaa_fq->xdp_rxq, dpaa_fq->net_dev,
| ^~~~~~~~~~~~~~~~
Commit b02e5a0ebb ("xsk: Propagate napi_id to XDP socket Rx path")
added an extra argument to function xdp_rxq_info_reg and commit
d57e57d0cd ("dpaa_eth: add XDP_TX support") didn't know about that
extra argument.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/r/20201203144343.790719-1-anders.roxell@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The timestamp fields should be copied to new skb too in
A-050385 workaround for later TX timestamping handling.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Link: https://lore.kernel.org/r/20201201075258.1875-1-yangbo.lu@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For XDP TX, even tough we start out with correctly aligned buffers, the
XDP program might change the data's alignment. For REDIRECT, we have no
control over the alignment either.
Create a new workaround for xdp_frame structures to verify the erratum
conditions and move the data to a fresh buffer if necessary. Create a new
xdp_frame for managing the new buffer and free the old one using the XDP
API.
Due to alignment constraints, all frames have a 256 byte headroom that
is offered fully to XDP under the erratum. If the XDP program uses all
of it, the data needs to be move to make room for the xdpf backpointer.
Disable the metadata support since the information can be lost.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Explicitly point that the current workaround addresses skbs. This change is
in preparation for adding a workaround for XDP scenarios.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After transmission, the frame is returned on confirmation queues for
cleanup. For this, store a backpointer to the xdp_frame in the private
reserved area at the start of the TX buffer.
No TX batching support is implemented at this time.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use an xdp_frame structure for managing the frame. Store a backpointer to
the structure at the start of the buffer before enqueueing for cleanup
on TX confirmation. Reserve DPAA_TX_PRIV_DATA_SIZE bytes from the frame
size shared with the XDP program for this purpose. Use the XDP
API for freeing the buffer when it returns to the driver on the TX
confirmation path.
The frame queues are shared with the netstack. The DPAA driver is a LLTX
driver so no explicit locking is required on transmission.
This approach will be reused for XDP REDIRECT.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the ndo_change_mtu callback to prevent users from setting an
MTU that would permit processing of S/G frames. The maximum MTU size
is dependent on the buffer size.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the XDP_DROP and XDP_PASS actions.
Avoid draining and reconfiguring the buffer pool at each XDP
setup/teardown by increasing the frame headroom and reserving
XDP_PACKET_HEADROOM bytes from the start. Since we always reserve an
entire page per buffer, this change only impacts Jumbo frame scenarios
where the maximum linear frame size is reduced by 256 bytes. Multi
buffer Scatter/Gather frames are now used instead in these scenarios.
Allow XDP programs to access the entire buffer.
The data in the received frame's headroom can be overwritten by the XDP
program. Extract the relevant fields from the headroom while they are
still available, before running the XDP program.
Since the headroom might be resized before the frame is passed up to the
stack, remove the check for a fixed headroom value when building an skb.
Allow the meta data to be updated and pass the information up the stack.
Scatter/Gather frames are dropped when XDP is enabled.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We maintain an skb backpointer in the software annotations area of Tx
frames. Introduce a structure for explicit handling.
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'
Fixes: ceeb03ad8e ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Explicitly enable the FSL_XGMAC_MDIO Kconfig option in order to have
MDIO access to internal and external PHYs.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201119145106.712761-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the control buffer descriptor (cbd) fields have endianness
restrictions while the commands passed into the control buffers
don't (with one exception). This patch fixes offending code,
by adding endianness accessors for cbd fields and removing the
unnecessary ones in case of data buffer fields. Currently there's
no need to convert all commands to little endian format, the patch
only focuses on fixing current endianness issues reported by sparse.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These particular fields are specified in the H/W reference
manual as having network byte order format, so enforce big
endian annotation for them and clear the related sparse
warnings in the process.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to a hardware issue, an access to MDIO registers
that is concurrent with other ENETC register accesses
may lead to the MDIO access being dropped or corrupted.
The workaround introduces locking for all register accesses
to the ENETC register space. To reduce performance impact,
a readers-writers locking scheme has been implemented.
The writer in this case is the MDIO access code (irrelevant
whether that MDIO access is a register read or write), and
the reader is any access code to non-MDIO ENETC registers.
Also, the datapath functions acquire the read lock fewer times
and use _hot accessors. All the rest of the code uses the _wa
accessors which lock every register access.
The commit introducing MDIO support is -
commit ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
but due to subsequent refactoring this patch is applicable on
top of a later commit.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and netfilter subtrees.
Current release - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous release - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even
if inner packet has IP_DF (don't fragment) set in its header
(when TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break
gso support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous release - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need
to be dropped
- always clone the skbs to make sure they have a reference on
the socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5R2w
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
Tx checksumming has been defeatured and completely removed
from the h/w reference manual. Made a little cleanup for the
TSE case as this is complementary code.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201103140213.3294-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver uses in_irq() + in_serving_softirq() magic to decide if NAPI
scheduling is required or packet processing.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
Use the `sched_napi' argument passed by the callback. It is set true if
called from the interrupt handler and NAPI should be scheduled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
The headroom reserved for received frames needs to be aligned to an
RX specific value. There is currently a discrepancy between the values
used in the Ethernet driver and the values passed to the FMan.
Coincidentally, the resulting aligned values are identical.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Impose a larger RX private data area only when the A050385 erratum is
present on the hardware. A smaller buffer size is sufficient in all
other scenarios. This enables a wider range of linear Jumbo frame
sizes in non-erratum scenarios, instead of turning to multi
buffer Scatter/Gather frames. The maximum linear frame size is
increased by 128 bytes for non-erratum arm64 platforms.
Cleanup the hardware annotations header defines in the process.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hi Linus,
Please, pull the following patches that replace zero-length arrays with
flexible-array members.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=vyu3
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on the second option,
using skb_realloc_headroom() to create a new skb to accommodate
PTP frames. Turns out that this method is not reliable, as
reallocation of skbs for PTP frames along with the required
overhead (skb_set_owner_w, consume_skb) is causing random
crashes in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time on the same device
(as seen in James' report).
Note that these crashes don't occur with a single TCP stream,
nor with multiple concurrent UDP streams, but only when multiple
TCP streams are run concurrently with the PTP packet flow
(doing skb reallocation).
This patch enforces the first method, by requesting enough
headroom from the stack to accommodate PTP frames, and so avoiding
skb_realloc_headroom() & co, and the crashes no longer occur.
There's no reason not to set needed_headroom to a large enough
value to accommodate PTP frames, so in this regard this patch
is a fix.
Reported-by: James Jurack <james.jurack@ametek.com>
Fixes: bee9e58c9e ("gianfar:don't add FCB length to hard_header_len")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201020173605.1173-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on skb_realloc_headroom()
to create new skbs to accommodate PTP frames. Turns out that
this method is not reliable in this context at least, as
skb_realloc_headroom() for PTP frames can cause random crashes,
mostly in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time with the PTP flow
on the same device (as seen in James' report). I also noticed
that when the system is loaded by sending multiple TCP streams,
the driver receives cloned skbs in large numbers.
skb_cow_head() instead proves to be stable in this scenario,
and not only handles cloned skbs too but it's also more efficient
and widely used in other drivers.
The commit introducing skb_realloc_headroom in the driver
goes back to 2009, commit 93c1285c5d
("gianfar: reallocate skb when headroom is not enough for fcb").
For practical purposes I'm referencing a newer commit (from 2012)
that brings the code to its current structure (and fixes the PTP
case).
Fixes: 9c4886e5e6 ("gianfar: Fix invalid TX frames returned on error queue when time stamping")
Reported-by: James Jurack <james.jurack@ametek.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201029081057.8506-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.
Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.
Fixes: f166f890c8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang warns about the extra parentheses in this comparison:
drivers/net/ethernet/freescale/ucc_geth.c:1361:28:
warning: equality comparison with extraneous parentheses
if ((ugeth->phy_interface == PHY_INTERFACE_MODE_SGMII))
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
It seems clear the intent here is to do a comparison not an
assignment, so drop the extra parentheses to avoid any confusion.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201023033236.3296988-1-mpe@ellerman.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple level MAC configuration based on phy interface type
from general port configuration.
Group together MAC and link configuration code.
Decouple external mdio bus creation from interface type
parsing. No longer return an (unhandled) error code when
phy_node not found, use phy_node to indicate whether the
port has a phy or not. No longer fall-through when serdes
configuration fails for the link modes that require
internal link configuration.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When packets are received on the error queue, this function under
net_ratelimit():
netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");
does not get printed. Instead we only see:
[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed
Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new group of devlink traps - PARSER_ERROR_DROPS.
This consists of registering the array of parser error drops supported,
controlling their action through the .trap_group_action_set() callback
and reporting an erroneous skb received on the error queue
appropriately.
DPAA2 devices do not support controlling the action of independent
parser error traps, thus the .trap_action_set() callback just returns an
EOPNOTSUPP while .trap_group_action_set() actually notifies the hardware
what it should do with a frame marked as having a header error.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support in dpaa2-eth for devlink. For the moment, just
register the device with devlink, add the corresponding devlink port and
implement the .info_get() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
mpc52xx_fec_stop() uses in_interrupt() to check if it is safe to sleep. All
callers run in well defined contexts.
Pass an argument from the callers indicating whether it is safe to sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a null-check for _pcs_, but it is being dereferenced
prior to this null-check. So, if _pcs_ can actually be null,
then there is a potential null pointer dereference that should
be fixed by null-checking _pcs_ before being dereferenced.
Addresses-Coverity-ID: 1497159 ("Dereference before null check")
Fixes: 94ae899b20 ("dpaa2-mac: add PCS support through the Lynx module")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SHARED_FS is enabled on a DPNI object the flow steering tables are
shared between all the traffic classes. Modify the driver so that we
only add a new flow steering entry on the TC#0 when this new option is
enabled.
Signed-off-by: Ionut-robert Aron <ionut-robert.aron@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to dpaa2_eth_link_state_update() is a leftover from the time
when on DPAA2 platforms the PHYs were started at boot time so when an
ifconfig was issued on the associated interface, the link status needed
to be checked directly from the ndo_open() callback.
This is not needed anymore since we are now properly integrated with the
PHY layer thus a link interrupt will come directly from the PHY
eventually without the need to call the sync function.
Fix this up by removing the call to dpaa2_eth_link_state_update().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to check if both the MDIO controller node and its
child node, the PCS device, are available since there is no chance that
the child node would be enabled when the parent it's not.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.
Fixes: 39344a8962 ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe. On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present. Since 0f183fd151 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.
Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include PCS support in the dpaa2-eth driver by integrating it with the
new Lynx PCS module. There is not much to talk about in terms of changes
needed in the dpaa2-eth driver since the only steps necessary are to
find the MDIO device representing the PCS, register it to the Lynx PCS
module and then let phylink know if its existence also.
After this, the PCS callbacks will be treated directly by Lynx, without
interraction from dpaa2-eth's part.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix below sparse warning in dpmac.c.
warning: cast to restricted __le64
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add PTP sync packet one-step timestamping support.
Before egress, one-step timestamping enablement needs,
- Enabling timestamp and FAS (Frame Annotation Status) in
dpni buffer layout.
- Write timestamp to frame annotation and set PTP bit in
FAS to mark as one-step timestamping event.
- Enabling one-step timestamping by dpni_set_single_step_cfg()
API, with offset provided to insert correction time on frame.
The offset must respect all MAC headers, VLAN tags and other
protocol headers accordingly. The correction field update can
consider delays up to one second. So PTP frame needs to be
filtered and parsed, and written timestamp into Sync frame
originTimestamp field.
The operation of API dpni_set_single_step_cfg() has to be done
when no one-step timestamping frames are in flight. So we have
to make sure the last one-step timestamping frame has already
been transmitted on hardware before starting to send the current
one. The resolution is,
- Utilize skb->cb[0] to mark timestamping request per packet.
If it is one-step timestamping PTP sync packet, queue to skb queue.
If not, transmit immediately.
- Schedule a work to transmit skbs in skb queue.
- mutex lock is used to ensure the last one-step timestamping packet
has already been transmitted on hardware through TX confirmation queue
before transmitting current packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a preparation for next hardware one-step timestamping
support. For DPAA2, the one step timestamping configuration on
hardware registers has to be done when there is no one-step timestamping
packet in flight. So we will have to use workqueue and skb queue
for such packets transmitting, to make sure waiting the last packet has
already been sent on hardware, and starting to transmit the current one.
So the tx timestamping flag in private data may not reflect the actual
request for the one-step timestamping packets of skb queue. This also
affects skb headroom allocation. Let's use skb->cb[0] to mark the
timestamping request for each skb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke dpaa2_eth_enable_tx_tstamp() once in code after building FD,
rather than calling it in dpaa2_eth_build_single_fd(),
dpaa2_eth_build_sg_fd_single_buf(), and dpaa2_eth_build_sg_fd().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a global ptp_qoriq structure pointer, and export to use.
The ptp clock operations will be used in dpaa2-eth driver.
For example, supporting one step timestamping needs to write
current time to hardware frame annotation before sending and
then hardware inserts the delay time on frame during sending.
So in driver, at least clock gettime operation will be needed
to make sure right time is written to hardware frame annotation
for one step timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add APIs of 1588 single step timestamping.
- dpni_set_single_step_cfg
- dpni_get_single_step_cfg
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/freescale/fec_ptp.c:523:6: warning:
variable 'ns' set but not used [-Wunused-but-set-variable]
523 | u64 ns;
| ^~
After commit 6605b730c0 ("FEC: Add time stamping code and a PTP
hardware clock"), variable 'ns' is never used in fec_time_keep(),
so removing it to avoid build warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the correct resolution for the conflict from
merging the "net" tree fix:
commit 26cb7085c8 ("enetc: Remove the mdio bus on PF probe bailout")
with the "net-next" new work:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
that moved mdio bus allocation to an ealier stage of
the PF probing routine.
Fixes: a57066b1a0 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some static functions in the dpaa2-eth driver don't have the dpaa2_eth_
prefix and this is becoming an inconvenience when looking at, for
example, a perf top output and trying to determine easily which entries
are dpaa2-eth related. Ammend this by adding the prefix to all the
functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the error path for regulator disable.
Fixes: 9269e5560b ("net: fec: add phy-reset-gpios PROBE_DEFER check")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch warning:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
alloc_channel() warn: passing zero to 'ERR_PTR'
setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.
In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.
Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.
To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory allocation for ethernet address hash table.
The code was wrongly allocating an array for eth hash table which
is incorrect because this is the main structure for eth hash table
(struct eth_hash_t) that contains inside a number of elements.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a safe check to avoid dereferencing null pointer
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter 'priority' is incorrectly forced to zero which ultimately
induces logically dead code in the subsequent lines.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check before using returned value to avoid dereferencing null pointer.
Fixes: 18a6c85fcc ("fsl/fman: Add FMan Port Support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Potentially overflowing expression (ts_freq << 16 and intgr << 16)
declared as type u32 (32-bit unsigned) is evaluated using 32-bit
arithmetic and then used in a context that expects an expression of
type u64 (64-bit unsigned) which ultimately is used as 16-bit
unsigned by typecasting to u16. Fixed by using an unsigned 32-bit
integer since the value is truncated anyway in the end.
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of invalid rule, a positive value EINVAL is returned here.
I think this is a typo error. It is necessary to return an error value.
Cc: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
For ENETC ports that register an external MDIO bus,
the bus doesn't get removed on the error bailout path
of enetc_pf_probe().
This issue became much more visible after recent:
commit 07095c025a ("net: enetc: Use DT protocol information to set up the ports")
Before this commit, one could make probing fail on the error
path only by having register_netdev() fail, which is unlikely.
But after this commit, because it moved the enetc_of_phy_get()
call up in the probing sequence, now we can trigger an mdiobus_free()
bug just by forcing enetc_alloc_msix() to return error, i.e. with the
'pci=nomsi' kernel bootarg (since ENETC relies on MSI support to work),
as the calltrace below shows:
kernel BUG at /home/eiz/work/enetc/net/drivers/net/phy/mdio_bus.c:648!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
Hardware name: LS1028A RDB Board (DT)
pstate: 80000005 (Nzcv daif -PAN -UAO BTYPE=--)
pc : mdiobus_free+0x50/0x58
lr : devm_mdiobus_free+0x14/0x20
[...]
Call trace:
mdiobus_free+0x50/0x58
devm_mdiobus_free+0x14/0x20
release_nodes+0x138/0x228
devres_release_all+0x38/0x60
really_probe+0x1c8/0x368
driver_probe_device+0x5c/0xc0
device_driver_attach+0x74/0x80
__driver_attach+0x8c/0xd8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x154/0x200
driver_register+0x64/0x120
__pci_register_driver+0x44/0x50
enetc_pf_driver_init+0x24/0x30
do_one_initcall+0x60/0x1c0
kernel_init_freeable+0x1fc/0x274
kernel_init+0x14/0x110
ret_from_fork+0x10/0x34
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_imdio_remove() is missing from the enetc_pf_probe()
bailout path. Not surprisingly because enetc_setup_serdes()
is registering the imdio bus for internal purposes, and it's
not obvious that enetc_imdio_remove() currently performs the
teardown of enetc_setup_serdes().
To fix this, define enetc_teardown_serdes() to wrap
enetc_imdio_remove() (improve code maintenance) and call it
on bailout and remove paths.
Fixes: 975d183ef0 ("net: enetc: Initialize SerDes for SGMII and USXGMII protocols")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
TBF can only be offloaded on DPAA2 when it's the root qdisc, ie it's a
per port shaper.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setup done for MQPRIO into a separate function so that
with the addition of another offload we do not crowd
dpaa2_eth_setup_tc(). After this restructuring it's easier to see what
is supported in terms of Qdisc offloading.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic dynamic interrupt moderation (dim)
framework to implement adaptive interrupt coalescing
on Rx. With the per-packet interrupt scheme, a high
interrupt rate has been noted for moderate traffic flows
leading to high CPU utilization. The 'dim' scheme
implemented by the current patch addresses this issue
improving CPU utilization while using minimal coalescing
time thresholds in order to preserve a good latency.
On the Tx side use an optimal time threshold value by
default. This value has been optimized for Tx TCP
streams at a rate of around 85kpps on a 1G link,
at which rate half of the Tx ring size (128) gets filled
in 1500 usecs. Scaling this down to 2.5G links yields
the current value of 600 usecs, which is conservative
and gives good enough results for 1G links too (see
next).
Below are some measurement results for before and after
this patch (and related dependencies) basically, for a
2 ARM Cortex-A72 @1.3Ghz CPUs system (32 KB L1 data cache),
using 60secs log netperf TCP stream tests @ 1Gbit link
(maximum throughput):
1) 1 Rx TCP flow, both Rx and Tx processed by the same NAPI
thread on the same CPU:
CPU utilization int rate (ints/sec)
Before: 50%-60% (over 50%) 92k
After: 13%-22% 3.5k-12k
Comment: Major CPU utilization improvement for a single flow
Rx TCP flow (i.e. netperf -t TCP_MAERTS) on a single
CPU. Usually settles under 16% for longer tests.
2) 4 Rx TCP flows + 4 Tx TCP flows (+ pings to check the latency):
Total CPU utilization Total int rate (ints/sec)
Before: ~80% (spikes to 90%) ~100k
After: 60% (more steady) ~4k
Comment: Important improvement for this load test, while the
ping test outcome does not show any notable
difference compared to before.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable programming of the interrupt coalescing registers
and allow manual configuration of the coalescing time
thresholds via ethtool. Packet thresholds have been fixed
to predetermined values as there's no point in making them
run-time configurable, also anticipating the dynamic interrupt
moderation (DIM) algorithm which uses fixed packet thresholds
as well. If the interface is up when the operation mode of
traffic interrupt events is changed by the user (i.e. switching
from default per-packet interrupts to coalesced interrupts),
the traffic needs to be paused in the process.
This patch also prepares the ground for introducing DIM on Rx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'struct enetc_bdr' is already '____cacheline_aligned_in_smp'.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt coalescing registers naming in the current revision
of the Ref Man (RM) is ICR, deprecating the ICIR name used
in earlier (draft) versions of the RM.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A reliable traffic pause (and reconfiguration) procedure
is needed to be able to safely make h/w configuration
changes during run-time, like changing the mode in which the
interrupts are operating (i.e. with or without coalescing),
as opposed to making on-the-fly register updates that
may be subject to h/w or s/w concurrency issues.
To this end, the code responsible of the run-time device
configurations that basically starts resp. stops the traffic
flow through the device has been extracted from the
the enetc_open/_close procedures, to the separate standalone
enetc_start/_stop procedures. Traffic stop should be as
graceful as possible, it lets the executing napi threads to
to finish while the interrupts stay disabled. But since
the napi thread will try to re-enable interrupts by clearing
the device's unmask register, the enable_irq/ disable_irq
API has been used to avoid this potential concurrency issue
and make the traffic pause procedure more reliable.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's time to differentiate between Rx and Tx ring sizes.
Not only Tx rings are processed differently than Rx rings,
but their default number also differs - i.e. up to 8 Tx rings
per device (8 traffic classes) vs. 2 Rx rings (one per CPU).
So let's set Tx rings sizes to half the size of the Rx rings
for now, to be conservative.
The default ring sizes were decreased as well (to the next
lower power of 2), to reduce the memory footprint, buffering
etc., since the measurements I've made so far show that the
rings are very unlikely to get full.
This change also anticipates the introduction of the
dynamic interrupt moderation (dim) algorithm which operates
on maximum packet thresholds of 256 packets for Rx and 128
packets for Tx.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dma_coerce_mask_and_coherent() fails, the alloced netdev need to be freed.
Fixes: 060ad66f97 ("dpaa_eth: change DMA device")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable and clk_disable_unprepare already
checked NULL clock parameter, so the additional checks are
unnecessary, just remove them.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DT information rather than in-band information from bootloader to
set up MAC for XGMII. For RGMII use the DT indication in addition to
RGMII defaults in hardware.
However, this implies that PHY connection information needs to be
extracted before netdevice creation, when the ENETC Port MAC is
being configured.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC has ethernet MACs capable of SGMII, 2500BaseX and USXGMII. But in
order to use these protocols some SerDes configurations need to be
performed. The SerDes is configurable via an internal PCS PHY which is
connected to an internal MDIO bus at address 0.
This patch basically removes the dependency on bootloader regarding
SerDes initialization.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to use snprintf() on a constant string, nor using magic
constant in the fixed code was a good idea.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Code of the form "if(x) x = 0" replaced with "x = 0".
Code of the form "if(x == a) x = a" removed.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initializing with 0 makes it much easier to identify time stamps from
otherwise uninitialized clock.
Initialization of PTP clock with current kernel time makes little sense as
PTP time scale differs from UTC time scale that kernel time represents.
It only leads to confusion when no actual PTP initialization happens, as
these time scales differ in a small integer number of seconds (37 at the
time of writing.)
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PPS feature could be useful even when hardware time stamping
of network packets is not in use, so remove offending check
for this condition from fec_ptp_enable_pps().
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix support for external PTP-aware devices such as DSA or PTP PHY:
Make sure we never time stamp tx packets when hardware time stamping
is disabled.
Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fsl_mc_get_endpoint() function can return an error or directly a
NULL pointer in case the peer device is not under the root DPRC
container. Treat this case also, otherwise it would lead to a NULL
pointer when trying to access the peer fsl_mc_device.
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If there is no valid MAC address in the device tree,
use a random MAC address.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC allocates 2K buffers, but looses some of it due to
alignment. It can however support an MTU bigger than the default. This
is particularly interesting when used in combination with Ethernet
switches supporting DSA, which have extra headers. The DSA core will
try to increase the MTU to support these extra headers. If the max
size defaults to that of standard Ethernet we get a warning. By
setting the max to what the driver actually supports, we avoid this
warning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memset().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ISR, we poll the event register for the queues in need of
service and then enter polled mode. After this point, the event
register will never be read again until we exit polled mode.
In a scenario where a UDP flow is routed back out through the same
interface, i.e. "router-on-a-stick" we'll typically only see an rx
queue event initially. Once we start to process the incoming flow
we'll be locked polled mode, but we'll never clean the tx rings since
that event is never caught.
Eventually the netdev watchdog will trip, causing all buffers to be
dropped and then the process starts over again.
Rework the NAPI poll to keep trying to consome the entire budget as
long as new events are coming in, making sure to service all rx/tx
queues, in priority order, on each pass.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On link down, the draining of the S/G cache should be done on all
_possible_ CPUs not just the ones that are online in that moment.
Fix this by changing the iterator.
Fixes: d70446ee1f ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous commit, in case of insufficient SKB headroom on the Tx
path instead of reallocing the SKB we now send a S/G frame descriptor.
Export the number of occurences of this case as a per CPU counter (in
debugfs) and a total number in the ethtool statistics - "tx converted sg
frames'.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of realloc-ing the skb on the Tx path when the provided headroom
is smaller than the HW requirements, create a Scatter/Gather frame
descriptor with only one entry.
Remove the '[drv] tx realloc frames' counter exposed previously through
ethtool since it is no longer used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rings bitmap of an interrupt vector encodes
which of the device's rings were assigned to that
interrupt vector.
Hence the iteration range of the tx rings bitmap
(for_each_set_bit()) should be the total number of
Tx rings of that netdevice instead of the number of
rings assigned to the interrupt vector.
Since there are 2 cores, and one interrupt vector for
each core, the number of rings asigned to an interrupt
vector is half the number of available rings.
The impact of this error is that the upper half of the
tx rings could still generate interrupts during napi
polling.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Two of the function parameters (qtype and index) were misspelled in the
associated descriptions of dpni_[set/get]_taildrop which led to sparse
warnings. Fix this by using the exact same names as present in the
function definition.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth.h header file includes dpaa2-eth-trace.h which includes
back dpaa2-eth leading to a recursion in the include path. Fix this by
removing the include of dpaa2-eth.h in the trace header.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should keep retrying to acquire buffers through the software portals
as long as the function returns -EBUSY and the number of retries is
__below__ DPAA2_ETH_SWP_BUSY_RETRIES.
Fixes: ef17bd7cc0 ("dpaa2-eth: Avoid unbounded while loops")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before passing the result of skb_to_sgvec() to dma_map_sg() check if any
error was returned.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of multiple traffic classes support, the number
of available frame queues grew significantly, overly inflating the
debugfs FQ statistics entry. Update it to only show the queues
which are actually in use (i.e. have a non-zero frame counter).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow metering entries in IEEE 802.1Qci is an optional function for a
flow filtering module. Flow metering is two rates two buckets and three
color marker to policing the frames. This patch only enable one rate one
bucket and in color blind mode. Flow metering instance are as
specified in the algorithm in MEF 10.3 and in Bandwidth Profile
Parameters. They are:
a) Flow meter instance identifier. An integer value identifying the flow
meter instance. The patch use the police 'index' as thin value.
b) Committed Information Rate (CIR), in bits per second. This patch use
the 'rate_bytes_ps' represent this value.
c) Committed Burst Size (CBS), in octets. This patch use the 'burst'
represent this value.
d) Excess Information Rate (EIR), in bits per second.
e) Excess Burst Size per Bandwidth Profile Flow (EBS), in octets.
And plus some other parameters. This patch set EIR/EBS default disable
and color blind mode.
v1->v2 changes:
- Use div_u64() as division replace the '/' report:
All errors (new ones prefixed by >>):
ld: drivers/net/ethernet/freescale/enetc/enetc_qos.o: in function `enetc_flowmeter_hw_set':
>> enetc_qos.c:(.text+0x66): undefined reference to `__udivdi3'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base on the tc flower offload police action add max frame size by the
parameter 'mtu'. Tc flower device driver working by the IEEE 802.1Qci
stream filter can implement the max frame size filtering. Add it to the
current hardware tc flower stearm filter driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we know the xgmac hardware always has a c45
compliant bus, let's try scanning for c22 capable
PHYs first. If we fail to find any, then it will
fall back to c45 automatically.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI support for xgmac MDIO bus registration while maintaining
the existing DT support.
The function mdiobus_register() inside of_mdiobus_register(), brings
up all the PHYs on the mdio bus and attach them to the bus.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN tag insertion/extraction offload is correctly
activated at probe time but deactivation of this feature
(i.e. via ethtool) is broken. Toggling works only for
Tx/Rx ring 0 of a PF, and is ignored for the other rings,
including the VF rings.
To fix this, the existing VLAN offload toggling code
was extended to all the rings assigned to a netdevice,
instead of the default ring 0 (likely a leftover from the
early validation days of this feature). And the code was
moved to the common set_features() function to fix toggling
for the VF driver too.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tlen field into struct tso_t, and change tso_start()
to return skb_transport_offset(skb) + tso->tlen
This removes from callers the need to use tcp_hdrlen(skb) and
will ease UDP segmentation offload addition.
v2: calls tso_start() earlier in otx2_sq_append_tso() [Jakub]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/sch_generic.h does not need to be included, remove it.
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.
Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.
With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.
Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class. This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.
Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.
Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit da722186f6 (net: fec: set GPR bit on suspend by DT
configuration) set the GPR reigster offset and bit in driver for
wake on lan feature.
But it introduces two issues here:
- one SOC has two instances, they have different bit
- different SOCs may have different offset and bit
So to support wake-on-lan feature on other i.MX platforms, it should
configure the GPR reigster offset and bit from DT.
So the patch is to improve the commit da722186f6 (net: fec: set GPR
bit on suspend by DT configuration) to support multiple ethernet
instances on i.MX series.
v2:
* switch back to store the quirks bitmask in driver_data
v3:
* suggested by Sascha Hauer, use a struct fec_devinfo for
abstracting differences between different hardware variants,
it can give more freedom to describe the differences.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa-eth driver probes on compatible string for the MAC node, and
the fman/mac.c driver allocates a dpaa-ethernet platform device that
triggers the probing of the dpaa-eth net device driver.
All of this is fine, but the problem is that the struct device of the
dpaa_eth net_device is 2 parents away from the MAC which can be
referenced via of_node. So of_find_net_device_by_node can't find it, and
DSA switches won't be able to probe on top of FMan ports.
It would be a bit silly to modify a core function
(of_find_net_device_by_node) to look for dev->parent->parent->of_node
just for one driver. We're just 1 step away from implementing full
recursion.
Actually there have already been at least 2 previous attempts to make
this work:
- Commit a1a50c8e4c ("fsl/man: Inherit parent device and of_node")
- One or more of the patches in "[v3,0/6] adapt DPAA drivers for DSA":
https://patchwork.ozlabs.org/project/netdev/cover/1508178970-28945-1-git-send-email-madalin.bucur@nxp.com/
(I couldn't really figure out which one was supposed to solve the
problem and how).
Point being, it looks like this is still pretty much a problem today.
On T1040, the /sys/class/net/eth0 symlink currently points to
../../devices/platform/ffe000000.soc/ffe400000.fman/ffe4e6000.ethernet/dpaa-ethernet.0/net/eth0
which pretty much illustrates the problem. The closest of_node we've got
is the "fsl,fman-memac" at /soc@ffe000000/fman@400000/ethernet@e6000,
which is what we'd like to be able to reference from DSA as host port.
For of_find_net_device_by_node to find the eth0 port, we would need the
parent of the eth0 net_device to not be the "dpaa-ethernet" platform
device, but to point 1 level higher, aka the "fsl,fman-memac" node
directly. The new sysfs path would look like this:
../../devices/platform/ffe000000.soc/ffe400000.fman/ffe4e6000.ethernet/net/eth0
And this is exactly what SET_NETDEV_DEV does. It sets the parent of the
net_device. The new parent has an of_node associated with it, and
of_dev_node_match already checks for the of_node of the device or of its
parent.
Fixes: a1a50c8e4c ("fsl/man: Inherit parent device and of_node")
Fixes: c6e26ea8c8 ("dpaa_eth: change device used")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver level bulking to the XDP_TX action.
An array of frame descriptors is held for each Tx frame queue and
populated accordingly when the action returned by the XDP program is
XDP_TX. The frames will be actually enqueued only when the array is
filled. At the end of the NAPI cycle a flush on the queued frames is
performed in order to enqueue the remaining FDs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the WRIOP version, the buffer size on the RX path must by a
multiple of 64 or 256. Handle this restriction properly by aligning down
the buffer size to the necessary value. Also, use the new buffer size
dynamically computed instead of the compile time one.
Fixes: 27c874867c ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver reserve some headroom used for hardware and
software annotation area in RX/TX buffers. Thus, xdp.data_hard_start
doesn't start at page boundary.
When XDP is configured the area reserved via dpaa2_fd_get_offset(fd) is
448 bytes of which XDP have reserved 256 bytes. As frame_sz is
calculated as an offset from xdp_buff.data_hard_start, an adjust from
the full PAGE_SIZE == DPAA2_ETH_RX_BUF_RAW_SIZE.
When doing XDP_REDIRECT, the driver doesn't need this reserved headroom
any-longer and allows xdp_do_redirect() to use it. This is an advantage
for the drivers own ndo-xdp_xmit, as it uses part of this headroom for
itself. Patch also adjust frame_sz in this case.
The driver cannot support XDP data_meta, because it uses the headroom
just before xdp.data for struct dpaa2_eth_swa (DPAA2_ETH_SWA_SIZE=64),
when transmitting the packet. When transmitting a xdp_frame in
dpaa2_eth_xdp_xmit_frame (call via ndo_xdp_xmit) is uses this area to
store a pointer to xdp_frame and dma_size, which is used in TX
completion (free_tx_fd) to return frame via xdp_return_frame().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Link: https://lore.kernel.org/bpf/158945339348.97035.8562488847066908856.stgit@firesoul
I ran into a randconfig build failure with CONFIG_FIXED_PHY=m
and CONFIG_GIANFAR=y:
x86_64-linux-ld: drivers/net/ethernet/freescale/gianfar.o:(.rodata+0x418): undefined reference to `fixed_phy_change_carrier'
It seems the same thing can happen with dpaa and ucc_geth, so change
all three to do an explicit 'select FIXED_PHY'.
The fixed-phy driver actually has an alternative stub function that
theoretically allows building network drivers when fixed-phy is
disabled, but I don't see how that would help here, as the drivers
presumably would not work then.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "location" is controlled by the user via the ethtool_set_rxnfc()
function. This update_cls_rule() function checks for array overflows
but it doesn't check if the value is negative. I have changed the type
to unsigned to prevent array underflows.
Fixes: afb90dbb5f ("dpaa2-eth: Add ethtool support for flow classification")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create an independent function that takes a particular frame queue and
an array of frame descriptors and tries to enqueue them until it hits
the maximum number fo retries. The same function will be used in the
next patch also on the XDP_TX path.
Also, create the dpaa2_eth_xdp_fds structure to incorporate the array of
FDs as well as the number of FDs already populated.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'Dan Carpenter' reported:
This code frees "sfi" and then dereferences it on the next line:
> kfree(sfi);
> clear_bit(sfi->index, epsfp.psfp_sfi_bitmap);
This "sfi->index" should be "index".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:427:20: warning:
symbol 'enetc_act_fwd' was not declared. Should it be static?
drivers/net/ethernet/freescale/enetc/enetc_qos.c:966:20: warning:
symbol 'enetc_check_flow_actions' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the related system resources were not released when enetc_hw_alloc()
return error in the enetc_pci_mdio_probe(), add iounmap() for error
handling label "err_hw_alloc" to fix it.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.
Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Care has to be taken when setting the MII_SPEED register, or it can
trigger an MII event> That then upsets the polling, due to an
unexpected pending event.
Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul says:
====================
net/smc: extent buffer mapping and port handling
Add functionality to map/unmap and register/unregister memory buffers for
specific SMC-R links and for the whole link group. Prepare LLC layer messages
for the support of multiple links and extent the processing of adapter events.
And add further small preparations needed for the SMC-R failover support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add tc flower offload for the enetc IEEE 802.1Qci(PSFP)
function. There are four main feature parts to implement the flow
policing and filtering for ingress flow with IEEE 802.1Qci features.
They are stream identify(this is defined in the P802.1cb exactly but
needed for 802.1Qci), stream filtering, stream gate and flow metering.
Each function block includes many entries by index to assign parameters.
So for one frame would be filtered by stream identify first, then
flow into stream filter block by the same handle between stream identify
and stream filtering. Then flow into stream gate control which assigned
by the stream filtering entry. And then policing by the gate and limited
by the max sdu in the filter block(optional). At last, policing by the
flow metering block, index choosing at the fitering block.
So you can see that each entry of block may link to many upper entries
since they can be assigned same index means more streams want to share
the same feature in the stream filtering or stream gate or flow
metering.
To implement such features, each stream filtered by source/destination
mac address, some stream maybe also plus the vlan id value would be
treated as one flow chain. This would be identified by the chain_index
which already in the tc filter concept. Driver would maintain this chain
and also with gate modules. The stream filter entry create by the gate
index and flow meter(optional) entry id and also one priority value.
Offloading only transfer the gate action and flow filtering parameters.
Driver would create (or search same gate id and flow meter id and
priority) one stream filter entry to set to the hardware. So stream
filtering do not need transfer by the action offloading.
This architecture is same with tc filter and actions relationship. tc
filter maintain the list for each flow feature by keys. And actions
maintain by the action list.
Below showing a example commands by tc:
> tc qdisc add dev eth0 ingress
> ip link set eth0 address 10:00:80:00:00:00
> tc filter add dev eth0 parent ffff: protocol ip chain 11 \
flower skip_sw dst_mac 10:00:80:00:00:00 \
action gate index 10 \
sched-entry open 200000000 1 8000000 \
sched-entry close 100000000 -1 -1
Command means to set the dst_mac 10:00:80:00:00:00 to index 11 of stream
identify module. Then setting the gate index 10 of stream gate module.
Keep the gate open for 200ms and limit the traffic volume to 8MB in this
sched-entry. Then direct the frames to the ingress queue 1.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to let ethtool enable/disable the tc flower offload
features. Hardware ENETC has the feature of PSFP which is for per-stream
policing. When enable the tc hw offloading feature, driver would enable
the IEEE 802.1Qci feature. It is only set the register enable bit for
this feature not enable for any entry of per stream filtering and stream
gate or stream identify but get how much capabilities for each feature.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 29ae6bd1b0.
The commit breaks ethernet function on i.MX6SX, i.MX7D, i.MX8MM,
i.MX8MQ, and i.MX8QXP platforms. Boot yocto system by NFS mounting
rootfs will be failed with the commit.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2110:30-31:
WARNING comparing pointer to 0
Avoid pointer type value compared to 0.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to polled IO for MDIO completion assumes that MII events
are only generated for MDIO transactions. However on some SoCs writing
to the MII_SPEED register can also trigger an MII event. As a result,
the next MDIO read has a pending MII event, and immediately reads the
data registers before it contains useful data. When the read does
complete, another MII event is posted, which results in the next read
also going wrong, and the cycle continues.
By writing 0 to the MII_DATA register before writing to the speed
register, this MII event for the MII_SPEED is suppressed, and polled
IO works as expected.
Fixes: 29ae6bd1b0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Reported-by: Andy Duan <fugang.duan@nxp.com>
Suggested-by: Andy Duan <fugang.duan@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building arm32 allmodconfig:
ERROR: modpost: "__aeabi_uldivmod"
[drivers/net/ethernet/freescale/dpaa2/fsl-dpaa2-eth.ko] undefined!
frames and cdan are both of type __u64 (unsigned long long) so we need
to use div64_u64 to avoid this issues.
Fixes: 460fd830dd ("dpaa2-eth: add channel stat to debugfs")
Link: https://github.com/ClangBuiltLinux/linux/issues/1012
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute the average number of frames processed for each CDAN (Channel
Data Availability Notification) and export it to debugfs detailed
channel stats.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers ndo_setup_tc call should return -EOPNOTSUPP, when it cannot
support the qdisc type. Other return values will result in failing the
qdisc setup. This lead to qdisc noop getting assigned, which will
drop all TX packets on the interface.
Fixes: ab1e6de2bd ("dpaa2-eth: Add mqprio support")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the bulk enqueue feature in .ndo_xdp_xmit.
We cannot use the XDP_XMIT_FLUSH since the architecture is not capable
to store all the frames dequeued in a NAPI cycle so we instead are
enqueueing all the frames received in a ndo_xdp_xmit call right away.
After setting up all FDs for the xdp_frames received, enqueue multiple
frames at a time until all are sent or the maximum number of retries is
hit.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a function that both creates a frame descriptor from
an xdp_frame and enqueues it, split this into two stages.
Add the dpaa2_eth_xdp_create_fd that just transforms an xdp_frame into a
FD while the actual enqueue callback is called directly from the ndo for
each frame.
This is particulary useful in conjunction with bulk enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dpaa2-eth driver to use the bulk enqueue function introduced
with the change to QBMAN ring mode. At the moment, no functional changes
are made but rather the driver just transitions to the new interface
while still enqueuing just one frame at a time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enqueue dpaa2-eth callback now returns the number of successfully
enqueued frames. This is a preliminary patch necessary for adding
support for bulk ring mode enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO transaction normally starts with 32 1s as a preamble. However
not all devices requires such a preamble. Add a device tree property
which allows the preamble to be suppressed. This will half the size of
the MDIO transaction, allowing faster transactions. But it should only
be used when all devices on the bus support suppressed preamble.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.
Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC station interface (SI) has a VLAN filter list and a port
flag (PSIPVMR) by which it can be put in "VLAN promiscuous" mode, which
enables the reception of VLAN-tagged traffic even if it is not in the
VLAN filtering list.
Currently the handling of this setting works like this: the port starts
off as VLAN promiscuous, then it switches to enabling VLAN filtering as
soon as the first VLAN is installed in its filter via
.ndo_vlan_rx_add_vid. In practice that does not work out very well,
because more often than not, the first VLAN to be installed is out of
the control of the user: the 8021q module, if loaded, adds its rule for
802.1p (VID 0) traffic upon bringing the interface up.
What the user is currently seeing in ethtool is this:
ethtool -k eno2
rx-vlan-filter: on [fixed]
which doesn't match the intention of the code, but the practical reality
of having the 8021q module install its VID which has the side-effect of
turning on VLAN filtering in this driver. All in all, a slightly
confusing experience.
So instead of letting this driver switch the VLAN filtering state by
itself, just wire it up with the rx-vlan-filter feature from ethtool,
and let it be user-configurable just through that knob, except for one
case, see below.
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some SoCs, such as the i.MX6, it is necessary to set a bit
in the SoC level GPR register before suspending for wake on lan
to work.
The fec platform callback sleep_mode_enable was intended to allow this
but the platform implementation was NAK'd back in 2015 [1]
This means that, currently, wake on lan is broken on mainline for
the i.MX6 at least.
So implement the required bit setting in the fec driver by itself
by adding a new optional DT property indicating the GPR register
and adding the offset and bit information to the driver.
[1] https://www.spinics.net/lists/netdev/msg310922.html
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit ed0a72e0de ("net/freescale: Clean drivers from static versions")
leave behind this, remove it .
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters
(other than adaptive rx, which will now be rejected by core).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22 ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit 3c68b8fffb ("dpaa_eth: FMan erratum A050385
workaround") even though it appears to have been an issue since the
introductory commit 9ad1a37493 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware timestamping support (PTP) on Rx requires extended
buffer descriptors, double the size of normal Rx descriptors.
On the current controller revision only the timestamping offload
requires extended Rx descriptors.
Since Rx timestamping can be turned on/off at runtime, make Rx ring
allocation configurable at runtime too. As a result, the static
config option FSL_ENETC_HW_TIMESTAMPING can be dropped and the
extended descriptors can be used only when Rx timestamping gets
activated.
The extension has the same size as the base descriptor, making
the descriptor iterators easy to update for the extended case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve maintainability of the code iterating the Rx buffer
descriptors to prepare it to support iterating extended Rx BD
descriptors as well.
Don't increment by one the h/w descriptor pointers explicitly,
provide an iterator that takes care of the h/w details.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the stats len computation code to make it easier
to add new stats counters.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existence of the DT port node is the first thing checked
at probe time, and probing won't reach this point if the node
is missing.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no valid MAC address in the device tree, use a random
MAC address.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the initialization of the MAC to be performed even if the
device tree does not provide a valid MAC address. Later a random
MAC address should be assigned by the Ethernet driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the set_mac_address() in the init() function.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core already zeroes out the struct ethtool_coalesce structure,
drivers don't have to set every field to 0 individually.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on ethtool to properly present the fact that FW and bus
are not available for the gianfar driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on ethtool to properly present the fact that FW is not
available for the ucc_geth driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on ethtool to properly present the fact that FW is not
available for the dpaa driver.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set static versions because linux kernel is
released all together with same version applicable to the whole
code base.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the DPAA2 ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config(), which are
more suited to the needs of the DPAA2 MC firmware than those available
via mac_config().
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -r so that PHY negotiation can be restarted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARCH_LAYERSCAPE isn't needed for this driver, it builds and
sends/receives traffic without this config option just fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing an unbind/bind operation the network is no longer
functional on i.MX6 (which has a single FEC instance):
# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind
# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/bind
[ 10.756519] pps pps0: new PPS source ptp0
[ 10.792626] libphy: fec_enet_mii_bus: probed
[ 10.799330] fec 2188000.ethernet eth0: registered PHC device 1
# udhcpc -i eth0
udhcpc: started, v1.31.1
[ 14.985211] fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
[ 14.993140] libphy: PHY fixed-0:00 not found
[ 14.997643] fec 2188000.ethernet eth0: could not attach to PHY
On SoCs with two FEC instances there are some cases where one FEC instance
depends on the other one being present. One such example is i.MX28, which
has the following FEC dependency as noted in the comments:
/*
* The i.MX28 dual fec interfaces are not equal.
* Here are the differences:
*
* - fec0 supports MII & RMII modes while fec1 only supports RMII
* - fec0 acts as the 1588 time master while fec1 is slave
* - external phys can only be configured by fec0
*
* That is to say fec1 can not work independently. It only works
* when fec0 is working. The reason behind this design is that the
* second interface is added primarily for Switch mode.
*
* Because of the last point above, both phys are attached on fec0
* mdio interface in board design, and need to be configured by
* fec0 mii_bus.
*/
Prevent the unbind operation to avoid these issues.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7b ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable network drivers to use phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not an error to unplug a cable from the ENETC port even with TSN
offloads, so don't spam the log with link-related messages from the
tc-taprio offload subsystem, a single notification is sufficient:
[10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down.
[10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down
Fixes: 2e47cb415f ("enetc: update TSN Qbv PSPEED set according to adjust link speed")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
-----BEGIN PGP SIGNATURE-----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=e4jk
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.6
QUICC Engine drivers
- Improve the QE drivers to be compatible with ARM/ARM64/PPC64
architectures
- Various cleanups to the QE drivers
* tag 'soc-fsl-next-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux: (49 commits)
soc: fsl: qe: remove set but not used variable 'mm_gc'
soc: fsl: qe: remove PPC32 dependency from CONFIG_QUICC_ENGINE
soc: fsl: qe: remove unused #include of asm/irq.h from ucc.c
net: ethernet: freescale: make UCC_GETH explicitly depend on PPC32
net/wan/fsl_ucc_hdlc: reject muram offsets above 64K
net/wan/fsl_ucc_hdlc: fix reading of __be16 registers
net/wan/fsl_ucc_hdlc: avoid use of IS_ERR_VALUE()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_fast.c
soc: fsl: qe: drop pointless check in qe_sdma_init()
soc: fsl: qe: drop use of IS_ERR_VALUE in qe_sdma_init()
soc: fsl: qe: avoid IS_ERR_VALUE in ucc_slow.c
soc: fsl: qe: refactor cpm_muram_alloc_common to prevent BUG on error path
soc: fsl: qe: drop broken lazy call of cpm_muram_init()
soc: fsl: qe: make cpm_muram_free() ignore a negative offset
soc: fsl: qe: make cpm_muram_free() return void
soc: fsl: qe: change return type of cpm_muram_alloc() to s32
serial: ucc_uart: access __be32 field using be32_to_cpu
serial: ucc_uart: limit brg-frequency workaround to PPC32
serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()
serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32
...
Link: https://lore.kernel.org/r/1578608351-23289-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the enetc driver is disabled, the mdio support fails to
get built:
drivers/net/dsa/ocelot/felix_vsc9959.o: In function `vsc9959_mdio_bus_alloc':
felix_vsc9959.c:(.text+0x19c): undefined reference to `enetc_hw_alloc'
felix_vsc9959.c:(.text+0x1d1): undefined reference to `enetc_mdio_read'
felix_vsc9959.c:(.text+0x1d8): undefined reference to `enetc_mdio_write'
Change the Makefile to enter the subdirectory for this as well.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper pointer to be passed as argument is hw
Detected using Coccinelle.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv->tx_ring[] has 16 elements but only priv->num_tx_rings are
set up, the rest are NULL. This ">" comparison should be ">=" to avoid
a potential crash.
Fixes: 0d08c9ec7d ("enetc: add support time specific departure base on the qos etf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This increases the MDIO hold time to 5 enet_clk cycles from the previous
value of 0. This is actually the out-of-reset value, that the driver was
previously overwriting with 0. Zero worked for the external MDIO, but
breaks communication with the internal MDIO buses on which the PCS of
ENETC SI's and Felix switch are found.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within the LS1028A SoC, the register map for the ENETC MDIO controller
is instantiated a few times: for the central (external) MDIO controller,
for the internal bus of each standalone ENETC port, and for the internal
bus of the Felix switch.
Refactoring is needed to support multiple MDIO buses from multiple
drivers. The enetc_hw structure is made an opaque type and a smaller
enetc_mdio_priv is created.
'mdio_base' - MDIO registers base address - is being parameterized, to
be able to work with different MDIO register bases.
The ENETC MDIO bus operations are exported from the fsl-enetc-mdio
kernel object, the same that registers the central MDIO controller (the
dedicated PF). The ENETC main driver has been changed to select it, and
use its exported helpers to further register its private MDIO bus. The
DSA Felix driver will do the same.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)
@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: 8151ee88ba ("dpaa_eth: use page backed rx buffers")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was
used on the remove path to free any allocated resources.
The ptp_qoriq IRQ is among these resources that are freed in
ptp_qoriq_free() even though it is also a managed one (allocated using
devm_request_threaded_irq).
Drop the resource managed version of requesting the IRQ in order to not
trigger a double free of the interrupt as below:
[ 226.731005] Trying to free already-free IRQ 126
[ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707
__free_irq+0x9c/0x2b8
[ 226.743435] Modules linked in:
[ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W
5.4.0-03629-gfd7102c32b2c-dirty #912
[ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT)
[ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO)
[ 226.766022] pc : __free_irq+0x9c/0x2b8
[ 226.769758] lr : __free_irq+0x9c/0x2b8
[ 226.773493] sp : ffff8000125039f0
(...)
[ 226.856275] Call trace:
[ 226.858710] __free_irq+0x9c/0x2b8
[ 226.862098] free_irq+0x30/0x70
[ 226.865229] devm_irq_release+0x14/0x20
[ 226.869054] release_nodes+0x1b0/0x220
[ 226.872790] devres_release_all+0x34/0x50
[ 226.876790] device_release_driver_internal+0x100/0x1c0
Fixes: d346c9e86d ("dpaa2-ptp: reuse ptp_qoriq driver")
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp and add it to the ethtool query
interface.
skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, QUICC_ENGINE depends on PPC32, so this in itself does not
change anything. In order to allow removing the PPC32 dependency from
QUICC_ENGINE and avoid allmodconfig build failures, add this explicit
dependency.
Also, the QE Ethernet has never been integrated on any non-PowerPC SoC
and most likely will not be in the future.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENETC hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. The CBS driver was loaded by the sch_cbs
interface when set in the QOS in the kernel.
Here is an example command to set 20Mbits bandwidth in 1Gbits port
for taffic class 7:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 cbs \
locredit -1470 hicredit 30 \
sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile,
make C=2 drivers/net/ethernet/freescale/enetc/enetc.o
one warning can be found:
drivers/net/ethernet/freescale/enetc/enetc.c:1439:5:
warning: symbol 'enetc_setup_tc_mqprio' was not declared.
Should it be static?
This patch make symbol enetc_setup_tc_mqprio static.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
ENETC has a register PSPEED to indicate the link speed of hardware.
It is need to update accordingly. PSPEED field needs to be updated
with the port speed for QBV scheduling purposes. Or else there is
chance for gate slot not free by frame taking the MAC if PSPEED and
phy speed not match. So update PSPEED when link adjust. This is
implement by the adjust_link.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EOPNOTSUPP instead of -EINVAL if the requested ioctl is not
implemented.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DPNI is connected to a MAC, export its associated counters.
Ethtool related functions are added in dpaa2_mac for returning the
number of counters, their strings and also their values.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an external PHY, pass the wake-on-lan request to the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an attached PHY try to handle the requested ioctl with its
handler, which allows the userspace to access PHY registers, for
example. This will make mii-diag and similar tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function is called at every link up event, although the
FQID values will only change when the DPNI is disconnected from the
current object and reconnected to a different one.
The patch also avoids the forward declaration of update_tx_fqids.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all the frames that are in flight have time to be processed
before the interface is completely brought down. Add a missing delay
for the Rx path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User reports that an application making an (incorrect) call to
restart AN on a fixed link DPAA interface triggers an error in
the kernel log while the returned EINVAL should be enough.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, the frames dropped on receive or transmit
were not displayed in the ethtool statistics, leaving the dropped
frames unaccounted for.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a page to store the scatter gather table on the transmit path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading skb fields, use information from the DPAA frame
descriptor.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the buffers used for reception from netdev_frags to pages.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the DPAA Ethernet driver is using three buffer pools
for each interface, with three different sizes for the buffers
provided for the FMan reception path. This patch reduces the
number of buffer pools to one per interface. This change is in
preparation of another, that will be switching from netdev_frags
to page backed buffers for the receive path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use platform_get_irq_byname_optional() and platform_get_irq_optional()
instead of platform_get_irq_byname() and platform_get_irq() for optional
IRQs to avoid below error message during probe:
[ 0.795803] fec 30be0000.ethernet: IRQ pps not found
[ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Condition was previously checked, removing duplicate code.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c92 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->if_mode" is type phy_interface_t which is an enum. In this
context GCC will treat the enum as an unsigned int so this error
handling is never triggered.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/gianfar.c:2070:6:
warning: symbol 'reset_gfar' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.
Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.
This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, a new counter for in flight
Tx frames is offered. Use it when bringing down the interface to
determine when all pending Tx frames have been processed by hardware
instead of sleeping a fixed amount of time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware versions expose more DPNI counters.
Export relevant ones via ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we prepare to read more pages from the DPNI stat counters,
reorganize the code a bit to make it easier to extend.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care about the individual files, we can remove the
stored dentry for the files, as they are not needed to be kept track of
at all.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC ports can manage the MDIO bus via local register
interface. However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).
Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers. For instance, on the LS1028A QDS board
where MDIO muxing is required. Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.
The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access. It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules. This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.
Fixes following sparse warning:
warning: incorrect type in assignment (different address spaces)
expected void *priv
got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHYLIB is not set, build enetc will fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c: undefined reference to `phy_disconnect'
enetc.c: undefined reference to `phy_start'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c: undefined reference to `phy_stop'
enetc.c: undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_set_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_mdio.o: In function `enetc_mdio_probe':
enetc_mdio.c: undefined reference to `mdiobus_alloc_size'
enetc_mdio.c: undefined reference to `mdiobus_free'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed a few places. One is in some ifdeffed code which will probably
never be re-enabled; the others are in drivers which can't currently be
compiled on x86.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add interrupt support for dpaa2 ptp clock,
including MC APIs and PPS interrupt support. Other events
haven't been supported in MC by now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same IP
block with eTSEC/DPAA/ENETC 1588 timer.
This patch is to convert to reuse ptp_qoriq driver by
using register ioremap and dropping related MC APIs.
However the interrupts could only be handled by MC which
fires MSIs to ARM cores. So the interrupt enabling and
handling still rely on MC APIs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement mqprio qdisc support by mapping traffic classes to
different hardware enqueue priorities. The maximum number of
supported traffic classes is an attribute of each DPNI object.
The traffic classes map to hardware priorities from highest (0)
to lowest (highest prio number). The skb priority information
received from the stack is used to select the hardware Tx queue
on which to enqueue the frame.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPNI objects can have multiple traffic classes, as reflected by
the num_tc attribute. Until now we ignored its value and only
used traffic class 0.
This patch adds support for multiple Tx traffic classes; we have
num_queues x num_tcs hardware queues available for each interface.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code configuring xps on the netdev TX queues to a
separate function. A subsequent patch will need to call
this in another context as well.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is using netdev_alloc_frag() for allocation in the
->ndo_start_xmit() path. That one is always invoked in a BH disabled
region so we could also use napi_alloc_frag().
Use napi_alloc_frag() for skb allocation.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment, the preempt_disable() statement is required
due to synchronisation in napi_alloc_frag(). The awful truth is that
local_bh_disable() is required because otherwise the NAPI poll callback
can be invoked while the open function setup buffers. This isn't
unlikely since the dpaa2 provides multiple devices.
The usage of napi_alloc_frag() has been removed in commit
27c874867c ("dpaa2-eth: Use a single page per Rx buffer")
which means that the comment is not accurate and the preempt_disable()
statement is not required.
Remove the outdated comment and the no longer required
preempt_disable().
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
