This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp and add it to the ethtool query
interface.
skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, QUICC_ENGINE depends on PPC32, so this in itself does not
change anything. In order to allow removing the PPC32 dependency from
QUICC_ENGINE and avoid allmodconfig build failures, add this explicit
dependency.
Also, the QE Ethernet has never been integrated on any non-PowerPC SoC
and most likely will not be in the future.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENETC hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. The CBS driver was loaded by the sch_cbs
interface when set in the QOS in the kernel.
Here is an example command to set 20Mbits bandwidth in 1Gbits port
for taffic class 7:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 cbs \
locredit -1470 hicredit 30 \
sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile,
make C=2 drivers/net/ethernet/freescale/enetc/enetc.o
one warning can be found:
drivers/net/ethernet/freescale/enetc/enetc.c:1439:5:
warning: symbol 'enetc_setup_tc_mqprio' was not declared.
Should it be static?
This patch make symbol enetc_setup_tc_mqprio static.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
ENETC has a register PSPEED to indicate the link speed of hardware.
It is need to update accordingly. PSPEED field needs to be updated
with the port speed for QBV scheduling purposes. Or else there is
chance for gate slot not free by frame taking the MAC if PSPEED and
phy speed not match. So update PSPEED when link adjust. This is
implement by the adjust_link.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EOPNOTSUPP instead of -EINVAL if the requested ioctl is not
implemented.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DPNI is connected to a MAC, export its associated counters.
Ethtool related functions are added in dpaa2_mac for returning the
number of counters, their strings and also their values.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an external PHY, pass the wake-on-lan request to the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is an attached PHY try to handle the requested ioctl with its
handler, which allows the userspace to access PHY registers, for
example. This will make mii-diag and similar tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_port_modes will be compiled if CONFIG_PHYLINK enabled,
dpaa2_mac_validate will be compiled if CONFIG_FSL_DPAA2_ETH enabled,
it should select CONFIG_PHYLINK when dpaa2_mac_validate call
phylink_set_port_modes
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_validate':
dpaa2-mac.c:(.text+0x3a1): undefined reference to `phylink_set_port_modes'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_connect':
dpaa2-mac.c:(.text+0x91a): undefined reference to `phylink_create'
dpaa2-mac.c:(.text+0x94e): undefined reference to `phylink_of_phy_connect'
dpaa2-mac.c:(.text+0x97f): undefined reference to `phylink_destroy'
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.o: In function `dpaa2_mac_disconnect':
dpaa2-mac.c:(.text+0xa9f): undefined reference to `phylink_disconnect_phy'
dpaa2-mac.c:(.text+0xab0): undefined reference to `phylink_destroy'
make: *** [vmlinux] Error 1
Fixes: 7194792308 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the phy_mode() function to return the if_mode through an
argument, similar to the new form of of_get_phy_mode().
This will help with handling errors in a common manner and also will fix
an always true condition.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2-eth driver now has support for connecting to its associated
PHY device found through standard OF bindings.
This happens when the DPNI object (that the driver probes on) gets
connected to a DPMAC. When that happens, the device tree is looked up by
the DPMAC ID, and the associated PHY bindings are found.
The old logic of handling the net device's link state by hand still
needs to be kept, as the DPNI can be connected to other devices on the
bus than a DPMAC: other DPNI, DPSW ports, etc. This logic is only
engaged when there is no DPMAC (and therefore no phylink instance)
attached.
The MC firmware support multiple type of DPMAC links: TYPE_FIXED,
TYPE_PHY. The TYPE_FIXED mode does not require any DPMAC management from
Linux side, and as such, the driver will not handle such a DPMAC.
Although PHYLINK typically handles SFP cages and in-band AN modes, for
the moment the driver only supports the RGMII interfaces found on the
LX2160A. Support for other modes will come later.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the function is called at every link up event, although the
FQID values will only change when the DPNI is disconnected from the
current object and reconnected to a different one.
The patch also avoids the forward declaration of update_tx_fqids.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all the frames that are in flight have time to be processed
before the interface is completely brought down. Add a missing delay
for the Rx path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User reports that an application making an (incorrect) call to
restart AN on a fixed link DPAA interface triggers an error in
the kernel log while the returned EINVAL should be enough.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, the frames dropped on receive or transmit
were not displayed in the ethtool statistics, leaving the dropped
frames unaccounted for.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a page to store the scatter gather table on the transmit path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading skb fields, use information from the DPAA frame
descriptor.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9c ("dpaa_eth: add support for hardware timestamping")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the buffers used for reception from netdev_frags to pages.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the DPAA Ethernet driver is using three buffer pools
for each interface, with three different sizes for the buffers
provided for the FMan reception path. This patch reduces the
number of buffer pools to one per interface. This change is in
preparation of another, that will be switching from netdev_frags
to page backed buffers for the receive path.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use platform_get_irq_byname_optional() and platform_get_irq_optional()
instead of platform_get_irq_byname() and platform_get_irq() for optional
IRQs to avoid below error message during probe:
[ 0.795803] fec 30be0000.ethernet: IRQ pps not found
[ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Condition was previously checked, removing duplicate code.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c92 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->if_mode" is type phy_interface_t which is an enum. In this
context GCC will treat the enum as an unsigned int so this error
handling is never triggered.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/gianfar.c:2070:6:
warning: symbol 'reset_gfar' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.
Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.
This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, a new counter for in flight
Tx frames is offered. Use it when bringing down the interface to
determine when all pending Tx frames have been processed by hardware
instead of sleeping a fixed amount of time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware versions expose more DPNI counters.
Export relevant ones via ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we prepare to read more pages from the DPNI stat counters,
reorganize the code a bit to make it easier to extend.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care about the individual files, we can remove the
stored dentry for the files, as they are not needed to be kept track of
at all.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t is better for reference counters since its
implementation can prevent overflows.
So convert atomic_t ref counters to refcount_t.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC ports can manage the MDIO bus via local register
interface. However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).
Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers. For instance, on the LS1028A QDS board
where MDIO muxing is required. Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.
The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access. It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules. This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.
Fixes following sparse warning:
warning: incorrect type in assignment (different address spaces)
expected void *priv
got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs
Fixes: ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHYLIB is not set, build enetc will fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c: undefined reference to `phy_disconnect'
enetc.c: undefined reference to `phy_start'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c: undefined reference to `phy_stop'
enetc.c: undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_set_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_mdio.o: In function `enetc_mdio_probe':
enetc_mdio.c: undefined reference to `mdiobus_alloc_size'
enetc_mdio.c: undefined reference to `mdiobus_free'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed a few places. One is in some ifdeffed code which will probably
never be re-enabled; the others are in drivers which can't currently be
compiled on x86.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add interrupt support for dpaa2 ptp clock,
including MC APIs and PPS interrupt support. Other events
haven't been supported in MC by now.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although dpaa2-ptp.c driver is a fsl_mc_driver which
is using MC APIs for register accessing, it's same IP
block with eTSEC/DPAA/ENETC 1588 timer.
This patch is to convert to reuse ptp_qoriq driver by
using register ioremap and dropping related MC APIs.
However the interrupts could only be handled by MC which
fires MSIs to ARM cores. So the interrupt enabling and
handling still rely on MC APIs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement mqprio qdisc support by mapping traffic classes to
different hardware enqueue priorities. The maximum number of
supported traffic classes is an attribute of each DPNI object.
The traffic classes map to hardware priorities from highest (0)
to lowest (highest prio number). The skb priority information
received from the stack is used to select the hardware Tx queue
on which to enqueue the frame.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPNI objects can have multiple traffic classes, as reflected by
the num_tc attribute. Until now we ignored its value and only
used traffic class 0.
This patch adds support for multiple Tx traffic classes; we have
num_queues x num_tcs hardware queues available for each interface.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code configuring xps on the netdev TX queues to a
separate function. A subsequent patch will need to call
this in another context as well.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is using netdev_alloc_frag() for allocation in the
->ndo_start_xmit() path. That one is always invoked in a BH disabled
region so we could also use napi_alloc_frag().
Use napi_alloc_frag() for skb allocation.
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment, the preempt_disable() statement is required
due to synchronisation in napi_alloc_frag(). The awful truth is that
local_bh_disable() is required because otherwise the NAPI poll callback
can be invoked while the open function setup buffers. This isn't
unlikely since the dpaa2 provides multiple devices.
The usage of napi_alloc_frag() has been removed in commit
27c874867c ("dpaa2-eth: Use a single page per Rx buffer")
which means that the comment is not accurate and the preempt_disable()
statement is not required.
Remove the outdated comment and the no longer required
preempt_disable().
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err() is more appropriate for printing error messages inside
drivers, so switch to dev_err().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this software may be used and distributed according to the terms of
the gnu public license version 2 incorporated herein by reference
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081035.599594316@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to configure multiple prioritized TX traffic
classes with mqprio.
Configure one BD ring per TC for the moment, one netdev
queue per TC.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keygen extracted fields are used as input for the hash that
determines the incoming frames distribution. Adding IPSEC SPI so
different IPSEC flows can be distributed to different CPUs.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure only the portals for the online CPUs are used.
Without this change, there are issues when someone boots with
maxcpus=n, with n < actual number of cores available as frames
either received or corresponding to the transmit confirmation
path would be offered for dequeue to the offline CPU portals,
getting lost.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blow sparse warning introduced by a previous patch.
- restricted __le32 degrades to integer
- restricted __le16 degrades to integer
Fixes: d398231219 ("enetc: add hardware timestamping support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function dpaa2_eth_cls_key_size() expects a 64bit argument,
but DPAA2_ETH_DIST_ALL is defined as UINT_MAX. Fix this.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PTR_ERR_OR_ZERO instead of PTR_ERR in cases where
zero is a valid input. Reported by smatch.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch reports a potential spectre vulnerability in the dpaa2-eth
driver, where the value of rxnfc->fs.location (which is provided
from user-space) is used as index in an array.
Add a call to array_index_nospec() to sanitize the access.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add get_ts_info interface for ethtool
to support getting timestamping capability.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add hardware timestamping support
for ENETC. On Rx, timestamping is enabled for all
frames. On Tx, we only instruct the hardware to
timestamp the frames marked accordingly by the stack.
Because the RX BD ring dynamic allocation has not been
supported and it is too expensive to use extended RX BDs
if timestamping is not used, a Kconfig option is used to
enable extended RX BDs in order to support hardware
timestamping. This option will be removed once RX BD
ring dynamic allocation is implemented.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f8b9958534.
The reverted change instructed the QMan hardware block to fetch
RX frame annotation and beginning of frame data to cache before
the core would read them.
It turns out that in rare cases, it's possible that a QMan
stashing transaction is delayed long enough such that, by the time
it gets executed, the frame in question had already been dequeued
by the core and software processing began on it. If the core
manages to unmap the frame buffer _before_ the stashing transaction
is executed, an SMMU exception will be raised.
Unfortunately there is no easy way to work around this while keeping
the performance advantages brought by QMan stashing, so disable
it altogether.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't disable the ipg clock in the regulator error path. The clock is
disable unconditionally two lines below the failed_regulator label.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just hook get_link to standard ethtool_op_get_link,
nothing special needed at this point.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that the Tx SG flag is fixed to 'on' is only
an oversight. Non-SG mode is also supported. Fix this
by allowing to turn SG off.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the unlikely case of TxBD extensions (i.e. ptp)
the driver tries to unmap the tx_swbd corresponding
to the extension, which is bogus as it has no buffer
attached.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix issue with the entry indexing in the sg frame cleanup code being
off-by-1. This problem showed up when doing some basic iperf tests and
manifested in traffic coming to a halt.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.
We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.
When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.
Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two macros to simplify reading DPNI options.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the Rx flow classification enable flag only if key config
operation is successful.
Fixes 3f9b5c9 ("dpaa2-eth: Configure Rx flow classification key")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the software Rx batching by using
netif_receive_skb_list instead of napi_gro_receive.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.
This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.
Fixes: 569dac6a5a ("dpaa2-eth: bql support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
Make logging of an ethernet address more consistent with
the rest of the kernel.
Miscellanea:
The %02hx use also did not quite match the u8 definition
of addr though that did not actually matter given normal
integer promotion rules.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the XDP_REDIRECT action.
The redirected frame is transmitted and confirmed on the regular Tx/Tx
conf queues. Frame is marked with the "XDP" type in the software
annotation, since it requires special treatment.
We don't have good hardware support for TX batching, so the
XDP_XMIT_FLUSH flag doesn't make a difference for now; ndo_xdp_xmit
performs the actual Tx operation on the spot.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We write different metadata information in the software annotation
area of Tx frames, depending on frame type. Make this more explicit
by introducing a type field and separate structures for single buffer
and scatter-gather frames.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPIO driver
- Add support for cache stashing and enable it in dpaa2-eth driver
GUTS driver
- Make fsl_guts_get_svr() API internal in favor of more generic
soc_device_match()
-----BEGIN PGP SIGNATURE-----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=tNfD
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.1 take4
DPIO driver
- Add support for cache stashing and enable it in dpaa2-eth driver
GUTS driver
- Make fsl_guts_get_svr() API internal in favor of more generic
soc_device_match()
* tag 'soc-fsl-next-v5.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Configure the amount of 64 bytes of frame, annotation and context data
that will be cache stashed for a specific frame queue. Since the frame
context is not used, configure that only 64 bytes of frame data and 64
bytes of annotation will be stashed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Passing the struct ptp_clock_info caps by parameter is passing over 130 bytes
of data by value on the stack. Optimize this by passing it by reference instead.
Also shinks the object code size:
Before:
text data bss dec hex filename
12596 2160 64 14820 39e4 drivers/ptp/ptp_qoriq.o
After:
text data bss dec hex filename
12567 2160 64 14791 39c7 drivers/ptp/ptp_qoriq.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for FEC devices.
Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:
#if defined(CONFIG_M523x) || defined(CONFIG_M527x)
|| defined(CONFIG_M528x) || defined(CONFIG_M520x)
|| defined(CONFIG_M532x) || defined(CONFIG_ARM)
|| defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add PTP clock driver for ENETC.
The driver reused QorIQ PTP clock driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strings containing "ptp_qoriq" or "qoriq_ptp" which were used for
structure/function names were complained by users. Let's just use
the unique "ptp_qoriq" to make these names more consistent.
This patch is just to unify the names using "ptp_qoriq". It hasn't
changed any functions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in mpc52xx_fec_tx_interrupt()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more buffers to the Rx buffer pool as soon as 7 of them
get consumed, instead of waiting for their number to drop
below a fixed threshold.
7 is the number of buffers that can be released in the pool
via a single DPIO command.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with MC10.14.0, dpaa2_io_service_enqueue_fq() API is
functional. Since there are a number of cases where it offers
better performance compared to the currently used enqueue
function, switch to it for firmware versions that support it.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While in NAPI context, free skbs by calling napi_consume_skb()
instead of dev_kfree_skb(), to take advantage of the bulk freeing
mechanism.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating page fragments via the network stack,
use the page allocator directly. For now, we consume one page
for each Rx buffer.
With the new memory model we are free to consider adding more
XDP support.
Performance decreases slightly in some IP forwarding cases.
No visible effect on termination traffic. The driver memory
footprint increases as a result of this change, but it is
still small enough to not really matter.
Another side effect is that now Rx buffer alignment requirements
are naturally satisfied without any additional actions needed.
Remove alignment related code, except in the buffer layout
information conveyed to MC, as hardware still needs to know the
alignment value we guarantee.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DPIO driver
- Clean up the remove path in the dpio driver so that successive
bind/unbind commands behave properly
- Add the ability to automatically create a device link between a
consumer device on the fsl-mc bus and a supplier one
- Add prefetch to dpio dequeue to improve performance
- Update the type of dpio APIs to align with buffer pool id register
field
guts driver
- Prevent allocation failure by reuse the machine type data from device
tree directly
-----BEGIN PGP SIGNATURE-----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=0PWU
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.1
DPIO driver
- Clean up the remove path in the dpio driver so that successive
bind/unbind commands behave properly
- Add the ability to automatically create a device link between a
consumer device on the fsl-mc bus and a supplier one
- Add prefetch to dpio dequeue to improve performance
- Update the type of dpio APIs to align with buffer pool id register
field
guts driver
- Prevent allocation failure by reuse the machine type data from device
tree directly
* tag 'soc-fsl-next-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: guts: reuse machine name from device tree
soc: fsl: dpio: Change bpid type to u16
soc: fsl: dpio: Add prefetch instruction
bus: fsl-mc: automatically add a device_link on fsl_mc_[portal,object]_allocate
soc: fsl: dpio: add a device_link at dpaa2_io_service_register
soc: fsl: dpio: store a backpointer to the device backing the dpaa2_io
soc: fsl: dpio: keep a per dpio device MC portal
soc: fsl: dpio: perform DPIO Reset on Probe
soc: fsl: dpio: use a cpumask to identify which cpus are unused
soc: fsl: dpio: cleanup the cpu array on dpaa2_io_down
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A ternary match table is used for RFS. If multiple entries in the table
match, the entry with the lowest numerical values index is chosen as the
matching entry. Entries in the table are identified using an index
which takes a value from 0 to PRFSCAPR[NUM_RFS]-1 when accessed by the
PSI (PF).
Portions of the RFS table can be assigned to each SI by the PSI (PF)
driver in PSIaRFSCFGR. Assignments are cumulative, the entries assigned
to SIn start after those assigned to SIn-1. The total assignments to
all SIs must be equal to or less than the number available to the port
as found in PRFSCAPR.
For RSS, the Toeplitz hash function used requires two inputs, a 40B
random secret key that is supplied through the PRSSKR0-9 registers as well
as the relevant pieces of the packet header (n-tuple). The 6 LSB bits of
the hash function result will then be used as a pointer to obtain the tag
referenced in the 64 entry indirection table. The result will provide a
winning group which will be used to help route the received packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSIs (VFs) may send a message to the PSI (PF) for general notification
or to gain access to hardware resources which requires host inspection.
These messages may vary in size and are handled as a partition copy
between two memory regions owned by the respective participants.
The PSI will respond with fail or success and a 16-bit message code.
The patch implements the vf to pf messaging mechanism above and, as the
first application making use of this support, it enables the VF to
configure its own primary MAC address.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds most h/w statistics counters: non-privileged SI conters, as
well as privileged Port and MAC counters available only to the PF.
Per ring software stats are also included.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE). As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.
Introduce basic PF and VF ENETC ethernet drivers. The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices. Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each. Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).
Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the device tree binding the phy-supply property is
optional. Use the regulator_get_optional API accordingly. The
code already handles NULL just fine.
This gets rid of the following warning:
fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converted to use "imply" instead of "select" for PTP_1588_CLOCK
driver selecting. This could break the hard dependency between
the PTP clock subsystem and ethernet drivers.
This patch also set "default y" for dpaa2 ptp driver building to
provide user an available ptp clock in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export detailed driver counters through debugfs.
Statistics already available in ethtool are presented in a
structured manner. Includes per-core, per-FQ and per-channel statistics.
Also transition from module_fsl_mc_driver to explicit module_init/exit
in order to create the debugfs directory besides registering the driver.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform dpaa2_eth_queue_count into a macro to follow the
the convention used by dpaa2_eth_fs_count and other functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, on interface down we disabled NAPI and
then manually drained any remaining ingress frames. This could lead
to a situation when, under heavy traffic, the data availability
notification for some of the channels would not get rearmed correctly.
Change the implementation such that we let all remaining ingress frames
be processed as usual and only disable NAPI once the hardware queues
are empty.
We also add a wait on the Tx side, to allow hardware time to process
all in-flight Tx frames before issueing the disable command.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically add a device link between the actual device requesting the
dpaa2_io_service_register and the underlying dpaa2_io used. This link
will ensure that when a DPIO device, which is indirectly used by other
devices, is unbound any consumer devices will be also unbound from their
drivers.
For example, any DPNI, bound to the dpaa2-eth driver, which is using
DPIO devices will be unbound before its supplier device.
Also, add a new parameter to the dpaa2_io_service_[de]register functions
to specify the requesting device (ie the consumer).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comments in the switch statement for XDP action to indicate
fallthrough is intended.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters for xdp processed frames to the channel statistics.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused counter. Reorder fields in channel stats structure
to match the ethtool strings order and make it easier to print them
with ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send frames back on the same port for XDP_TX action.
Since the frame buffers have been allocated by us, we can recycle
them directly into the Rx buffer pool instead of requesting a
confirmation frame upon transmission complete.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support enqueueing Rx FDs back to hardware, we need to
DMA map Rx buffers as bidirectional.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of freeing the RX buffers, release them back into the pool.
We wait for the maximum number of buffers supported by a single
release command to accumulate before issuing the command.
Also, don't unmap the Rx buffers at the beginning of the Rx routine
anymore, since that would require remapping them before release.
Instead, just do a DMA sync at first and only unmap if the frame is
meant for the stack.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll use function free_bufs() on the XDP path as well, so move
it higher in order to avoid a forward declaration.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve XDP_PACKET_HEADROOM bytes in Rx buffers to allow XDP
programs to increase frame header size.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We keep one XDP program reference per channel. The only actions
supported for now are XDP_DROP and XDP_PASS.
Until now we didn't enforce a maximum size for Rx frames based
on MTU value. Change that, since for XDP mode we must ensure no
scatter-gather frames can be received.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool control of the DPAA QMan portal interrupt coalescing
settings.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove directly accessing device_node.type pointer and use the accessors
instead. This will eventually allow removing the type pointer.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for byte queue limit.
On NAPI poll, we save the total number of Tx confirmed frames/bytes
and register them with bql at the end of the poll function.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the frame consume callback signature:
* the entire FQ structure is passed to the callback instead
of just the queue index
* the NAPI structure can be easily obtained from the channel
it is associated to, so we don't need to pass it explicitly
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPNI object on which we build a network interface has a
certain number of {Rx, Tx, Tx confirmation} frame queues as
resources. The default hardware setup offers one queue of each
type, as well as one DPCON channel, for each core available
in the system.
There are however cases where the number of queues is greater
than the number of cores or channels. Until now, we configured
and used all the frame queues associated with a DPNI, even if it
meant assigning multiple queues of one type to the same channel.
Update the driver to only use a number of queues equal to the
number of channels, ensuring each channel will contain exactly
one Rx and one Tx confirmation queue.
>From the user viewpoint, this change is completely transparent.
Performance wise there is no impact in most scenarios. In case
the number of queues is larger than and not a multiple of the
number of channels, Rx hash distribution offers now better load
balancing between cores, which can have a positive impact on
overall system performance.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl_mc_portal_allocate can fail when the requested MC portals are
not yet probed by the fsl_mc_allocator. In this situation, the driver
should defer the probe.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl_mc_object_allocate function can fail because not all allocatable
objects are probed by the fsl_mc_allocator at the call time. Defer the
dpaa2-eth probe when this happens.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit db65f35f50 ("net: fec: add support of ethtool get_regs") introduce
ethool "--register-dump" interface to dump all FEC registers.
But not all silicon implementations of the Freescale FEC hardware module
have the FRBR (FIFO Receive Bound Register) and FRSR (FIFO Receive Start
Register) register, so we should not be trying to dump them on those that
don't.
To fix it we create a quirk flag, FEC_QUIRK_HAS_RFREG, and check it before
dump those RX FIFO registers.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware ArchDef, the PTV1 field in FD[CTRL]
is ignored by WRIOP, so setting it for Tx FDs is pointless.
Remove all references to it from the code.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ch parameter is never used in the dpaa2_eth_tx_conf function but
since its prototype must match the type defined in the consume field of
struct dpaa2_eth_fq, just mark it as __always_unused.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv parameter is never used in the build_linear_skb and
drain_channel function. Remove it from the function definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 3 cases of possible uninitialized variables are false
positives since they are used only as output parameters.
Nonetheless, fix the warnings.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2_eth_set_dist_key function is only used in a single file.
Make it static.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ARCH_LAYERSCAPE and COMPILE_TEST dependencies are already implied
through the FSL_MC_BUS dep, so there's no need to state it explicitly.
Also, the fsl-mc bus depends on COMPILE_TEST only for some
architectures (arm, arm64, ppc, x86), so it's not correct to
claim build support unconditionally.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.
Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.
The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and improve dpaa2-ptp driver
in some places.
- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2734:34: warning:
tentative array definition assumed to have one element
static const struct of_device_id dpaa_match[];
^
1 warning generated.
Turns out that since this driver was introduced in commit 9ad1a37493
("dpaa_eth: add support for DPAA Ethernet"), this declaration has been
unused. Remove it to silence the warning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for inserting and deleting Rx flow classification
rules through ethtool.
We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.
Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For firmware versions that support it, configure an Rx flow
classification key at probe time.
Hardware expects all rules in the classification table to share
the same key. So we setup a key containing all supported fields
at driver init and when a user adds classification rules through
ethtool, we will just mask out the unused header fields.
Since the key composition process is the same for flow
classification and hashing, reuse existing code where possible.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the array of supported header fields will be used for
Rx flow classification as well, rename it from "hash_fields" to
the more inclusive "dist_fields".
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification through ethtool.
Starting with version 10.7.0, the Management Complex(MC) offers
a new set of APIs for separate configuration of Rx hashing and
classification keys.
Update the Rx flow hashing support to use the new API, if available.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During certain heavy network loads TX could time out
with TX ring dump.
TX is sometimes never restarted after reaching
"tx_stop_threshold" because function "fec_enet_tx_queue"
only tests the first queue.
In addition the TX timeout callback function failed to
recover because it also operated only on the first queue.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the only users of the oldadv/newadv variables
accidentally left the now-unused declarations behind:
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam':
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable]
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable]
Fixes: 70814e819c ("net: ethernet: Add helper for set_pauseparam for Asym Pause")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the Rx flow hash key was a 5-tuple (IP src, IP dst,
IP nextproto, L4 src port, L4 dst port) fixed value that we
configured at probe.
Add support for configuring this hash key at runtime.
We support all standard header fields configurable through ethtool,
but cannot differentiate between flow types, so the same hash key
is applied regardless of protocol.
We also don't support the discard option.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIV_ROUND_UP has implemented the code-opened function. Therefore, just
replace the implementation with DIV_ROUND_UP.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both WARN_ON() and WARN_ONCE() already contain an unlikely(), so it's not
necessary to wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not define again the polynomial but use header with existing define.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use generic kernel CRC32 implementation because it:
1. Should be faster (uses lookup tables),
2. Removes duplicated CRC generation code,
3. Uses well-proven algorithm instead of coding it one more time.
Suggested-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic kernel CRC32 implementation because it:
1. Should be faster (uses lookup tables),
2. Removes duplicated CRC generation code,
3. Uses well-proven algorithm instead of coding it one more time.
Suggested-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable last_rule_idx is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'last_rule_idx' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'inc' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'inc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the get_ts_info interface for ethtool to check
the timestamping capability.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add hardware timestamping support
for dpaa_eth. On Rx, timestamping is enabled for
all frames. On Tx, we only instruct the hardware
to timestamp the frames marked accordingly by the
stack.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defined frame description command FM_FD_CMD_UPD for
prepended data updating.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add fman_port_get_tstamp() interface
to get timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add set_tstamp interface for memac,
dtsec, and 10GEC controllers to configure HW timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to share fman event interrupt because
the 1588 timer driver will also use this interrupt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While compile-testing on arm64 with gcc-8.1, I ran into a build diagnostic:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_probe':
drivers/net/ethernet/freescale/fec_main.c:3517:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(irq_name, "int%d", i);
^~
drivers/net/ethernet/freescale/fec_main.c:3517:21: note: directive argument in the range [0, 2147483646]
sprintf(irq_name, "int%d", i);
^~~~~~~
drivers/net/ethernet/freescale/fec_main.c:3517:3: note: 'sprintf' output between 5 and 14 bytes into a destination of size 8
sprintf(irq_name, "int%d", i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
It appears this has never shown on ppc32 or arm32 for an unknown reason, but
now gcc fails to identify that the 'irq_cnt' loop index has an upper bound
of 3, and instead uses a bogus range.
To work around the warning, this changes the sprintf to snprintf with the
correct buffer length.
Fixes: 78cc6e7ef9 ("net: ethernet: freescale: Allow FEC with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This comment is outdated as fec_ptp_ioctl has been replaced by fec_ptp_set/fec_ptp_get
since commit 1d5244d0e4 ("fec: Implement the SIOCGHWTSTAMP ioctl")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no license information in the header of
this file.
The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in tx_fw_stat_gstrings text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check port->rev_info.major >= 6 is being performed twice, thus
the inner second check is always true and is redundant, hence it
can be removed. Detected by cppcheck.
drivers/net/ethernet/freescale/fman/fman_port.c:1394]: (warning)
Identical inner 'if' condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a simpler and generic method for for finding (and mapping)
the TBIPA register.
Instead of relying of complicated logic for finding the TBIPA register
address based on the MDIO or MII register block base
address, which even in some cases relies on undocumented shadow registers,
a second "reg" entry for the mdio bus devicetree node specifies the TBIPA
register.
Backwards compatibility is kept, as the existing logic is applied when
only a single "reg" mapping is specified.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform device is no longer used for DMA mapping so the
(questionable) setting of the DMA ops done here is no longer
needed. Removing it together with the HAS_DMA dependency that
it required.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_errors counter is incremented by the dpaa_xmit caller.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fd_format has already been initialized at this point.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent changes that make the driver probing compatible with DSA
were not propagated in the dpa_remove() function, breaking the
module unload function. Using the proper device to address the issue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec7711 ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds allmulticast option for memac, dtsec
and 10GEC controllers.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid some Rx errors not being
accounted.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue in the code mapping the skb fragments into
scatter-gather frames was evidentiated by netperf
TCP_SENDFILE tests. The size was set wrong for all
fragments but the first, affecting the transmission
of any skb with more than one fragment.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADVERTISED_Asym_Pause bit was being improperly set when both
rx and tx pause were enabled. When rx and tx are both enabled, only
the ADVERTISED_Pause bit is supposed to be set.
Signed-off-by: Jake Moroni <mail@jakemoroni.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment stated that a thread was started, but
that is not the case.
Signed-off-by: Jake Moroni <mail@jakemoroni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c021ec60] skb_pull+0x24/0x44
LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[df7edf40] [c023352c] net_rx_action+0x21c/0x274
[df7edf90] [c0329000] __do_softirq+0xd8/0x240
[df7edff0] [c000c108] call_do_irq+0x24/0x3c
[c0597e90] [c00041dc] do_IRQ+0x64/0xc4
[c0597eb0] [c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes: 6c389fc931 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX8 is a ARMv8 based SoC, that uses the same FEC IP as the
earlier, ARMv7 based, i.MX SoCs. Allow the driver to work on ARM64.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes in probe error path:
- Restore dev_id before failed_ioremap path.
Fixes: ("net: fec: restore dev_id in the cases of probe error")
- Call of_node_put(phy_node) before failed_phy path.
Fixes: ("net: fec: Support phys probed from devicetree and fixed-link")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer probe if regulator is not ready. E.g. some regulator is fixed
regulator controlled by i2c expander gpio, the i2c device may be probed
after the driver, then it should handle the case of defer probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static variable dev_id always plus one before netdev registerred.
It should restore the dev_id value in the cases of probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:
log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed
The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
the refclk on and off again during operation (according to their
datasheet). Nonetheless exactly this behaviour was introduced for power
saving reasons by commit e8fcfcd568 ("net: fec: optimize the clock management to save power").
Therefore add support for the phy_reset_after_clk_enable function from
phylib to mitigate this issue.
Generally speaking this issue is only relevant if the ref clk for the
PHY is generated by the SoC and therefore the PHY is configured to
"REF_CLK In Mode". In our specific case (PCB) this problem does occur at
about every 10th to 50th POR of an LAN8710 connected to an i.MX6SOLO
SoC. The typical symptom of this problem is a "swinging" ethernet link.
Similar issues were reported by users of the NXP forum:
https://community.nxp.com/thread/389902https://community.nxp.com/message/309354
With this patch applied the issue didn't occur for at least a few
hundret PORs of our board.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to LS1021A RM, the value of PAL can be set so that the start of the
IP header in the receive data buffer is aligned to a 32-bit boundary. Normally,
setting PAL = 2 provides minimal padding to ensure such alignment of the IP
header.
However every incoming packet's 8-byte time stamp will be inserted into the
packet data buffer as padding alignment bytes when hardware time stamping is
enabled.
So we set the padding 8+2 here to avoid the flooded alignment faults:
root@128:~# cat /proc/cpu/alignment
User: 0
System: 17539 (inet_gro_receive+0x114/0x2c0)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 17539
User faults: 2 (fixup)
Also shown when exception report enablement
CPU: 0 PID: 161 Comm: irq/66-eth1_g0_ Not tainted 4.1.21-rt13-WR8.0.0.0_preempt-rt #16
Hardware name: Freescale LS1021A
[<8001b420>] (unwind_backtrace) from [<8001476c>] (show_stack+0x20/0x24)
[<8001476c>] (show_stack) from [<807cfb48>] (dump_stack+0x94/0xac)
[<807cfb48>] (dump_stack) from [<80025d70>] (do_alignment+0x720/0x958)
[<80025d70>] (do_alignment) from [<80009224>] (do_DataAbort+0x40/0xbc)
[<80009224>] (do_DataAbort) from [<80015398>] (__dabt_svc+0x38/0x60)
Exception stack(0x86ad1cc0 to 0x86ad1d08)
1cc0: f9b3e080 86b3d072 2d78d287 00000000 866816c0 86b3d05e 86e785d0 00000000
1ce0: 00000011 0000000e 80840ab0 86ad1d3c 86ad1d08 86ad1d08 806d7fc0 806d806c
1d00: 40070013 ffffffff
[<80015398>] (__dabt_svc) from [<806d806c>] (inet_gro_receive+0x114/0x2c0)
[<806d806c>] (inet_gro_receive) from [<80660eec>] (dev_gro_receive+0x21c/0x3c0)
[<80660eec>] (dev_gro_receive) from [<8066133c>] (napi_gro_receive+0x44/0x17c)
[<8066133c>] (napi_gro_receive) from [<804f0538>] (gfar_clean_rx_ring+0x39c/0x7d4)
[<804f0538>] (gfar_clean_rx_ring) from [<804f0bf4>] (gfar_poll_rx_sq+0x58/0xe0)
[<804f0bf4>] (gfar_poll_rx_sq) from [<80660b10>] (net_rx_action+0x27c/0x43c)
[<80660b10>] (net_rx_action) from [<80033638>] (do_current_softirqs+0x1e0/0x3dc)
[<80033638>] (do_current_softirqs) from [<800338c4>] (__local_bh_enable+0x90/0xa8)
[<800338c4>] (__local_bh_enable) from [<8008025c>] (irq_forced_thread_fn+0x70/0x84)
[<8008025c>] (irq_forced_thread_fn) from [<800805e8>] (irq_thread+0x16c/0x244)
[<800805e8>] (irq_thread) from [<8004e490>] (kthread+0xe8/0x104)
[<8004e490>] (kthread) from [<8000fda8>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397960
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation functions already display some informaton in case of
memory allocation failure. There is no need to add an extra 'dev_err' here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'of_phy_find_device()' fails, we must undo the previous 'of_node_get()'
call, as done the the following error handling code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to release explicitly some devm_ allocated resources.
If the 'mac_probe()' probe function fails, they will be released
automatically, as already done in the other error handling paths of
this function.
Also goto '_return_of_get_parent' as in the other error handling paths.
This is useless (priv->fixed_link is NULL at this point), but at least
it is consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c6e26ea8c8 ("dpaa_eth: change device used") has removed usage of
'dev_set_drvdata()' in the 'mac_probe() function.
This call should also be axed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the dpaa_bp_alloc() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is better for code locality and should slightly
speed up normal interrupts.
This also allows PPS clock output to start working for
i.mx7. This is because i.mx7 was already using the limit
of 3 interrupts, and needed another.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now build this driver on ARM, so I ran into a randconfig build
warning that presumably had existed on powerpc already.
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function 'sg_fd_to_skb':
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1712:18: error: 'skb' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm slightly changing the logic here, to make it obvious to the
compiler that 'skb' is always initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comment is no longer valid for a long time now.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change just renames the FMan driver modules, using a common prefix
for the DPAA FMan and DPAA Ethernet drivers. Besides making the names more
aligned, this allows writing udev rules that match on either driver name,
if needed, using the fsl_dpaa_* prefix. The change of netdev dev required
for the DSA probing makes the previous rules written using this prefix
fail, this change makes them work again, ensuring backwards compatibility
for their users.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change device used for DMA mapping to the MAC device that is an
of_device, with proper DMA ops. Using this device for the netdevice
should also address the issue with DSA scenarios that need the
netdevice to be backed by an of_device.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan MAC driver allocates a platform device for the Ethernet
driver to probe on. Setting pdev->dev.of_node with the MAC node
triggers the MAC driver probing of the new platform device. While
this fails quickly and does not affect the functionality of the
drivers, it is incorrect and must be removed. This was added to
address a report that DSA code using of_find_net_device_by_node()
is unable to use the DPAA interfaces. Error message seen before
this fix:
fsl_mac dpaa-ethernet.0: __devm_request_mem_region(mac) failed
fsl_mac: probe of dpaa-ethernet.0 failed with error -16
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes unused timer and its old initialization call.
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC_ENET_TS_TIMER is not checked in the interrupt routine
so there is no need to enable it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
uf_info.regs is resource_size_t i.e. phys_addr_t that can be either u32
or u64 according to CONFIG_PHYS_ADDR_T_64BIT.
The printk format is thus adaptet to u64 and the regs value cast to u64
to take both u32 and u64 into account.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_ids on the stack, instead make them static.
Makes the object code smaller by over 700 bytes:
Before:
text data bss dec hex filename
28785 5832 192 34809 87f9 fman.o
After:
text data bss dec hex filename
27921 5992 192 34105 8539 fman.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the skb hash when then FMan Keygen hash result is available.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool control of the Rx flow hashing. By default RSS is
enabled, this allows to turn it off by bypassing the FMan Keygen
block and sending all traffic on the default Rx frame queue.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a block of 128 Rx frame queues per port. The FMan hardware will
send traffic on one of these queues based on the FMan port Parse
Classify Distribute setup. The hash computed by the FMan Keygen
block will select the Rx FQ.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FMan Keygen with a hardcoded scheme to spread
incoming traffic on a FQ range based on source and destination IPs
and ports.
Signed-off-by: Iordache Florinel <florinel.iordache@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is only stored in a const field of a
mdiobb_ctrl structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented workarounds for the following dTSEC Erratum:
A002, A004, A0012, A0014, A004839 on several operations
that involve MAC CFG register changes: adjust link,
rx pause frames, modify MAC address.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
19057 392 0 19449 4bf9 drivers/net/ethernet/freescale/gianfar.o
File size After adding 'const':
text data bss dec hex filename
19249 192 0 19441 4bf1 drivers/net/ethernet/freescale/gianfar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit (5567e98919) inserted a dependency on DMA
API that requires HAS_DMA to be added in Kconfig.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the use of arch_setup_dma_ops() that was not exported
and was breaking loadable module compilation.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure dma_ops are set, to be later used by the Ethernet driver.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.
Add the missing empty stub to fix the build failure.
Fixes: Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.
Tested on an IMX51.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
Since commit 5093bb965a ("powerpc/QE: switch to the cpm_muram
implementation"), muram area is not part of immrbar mapping anymore
so immrbar_virt_to_phys() is not usable anymore.
Fixes: 5093bb965a ("powerpc/QE: switch to the cpm_muram implementation")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Li Yang <pku.leo@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The errata ERR007885 HW fix don't add to i.MX6ul ENET IP version,
so add sw workaroud for the chip.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the errata number ERR006358 comment typo.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many boards use i2c/spi expander gpio as phy-reset-gpios and these
gpios maybe registered after fec port, driver should check the return
value of .of_get_named_gpio().
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, it requires to trasfer ->dev to dma_alloc_coherent()
API, otherwise allocate failed and print kernel warning.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, the BD pointer is 64bit, and the high-order 32-bits
of the address is effective, so replace usigned with (void *) type to
aovid 64bit address is casted to 32bit in .fec_enet_get_nextdesc() and
.fec_enet_get_prevdesc() functions.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add return value check after calling .of_property_read_u32() to avoid
the warning reported by coverity.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_8xx is being deprecated. Since the includes dependent on
CONFIG_8xx are useless, just drop them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the setup_tc ndo to configure prioritised Tx traffic classes.
Priorities range from 0 (lowest) to 3 (highest). The driver assigns
NR_CPUS queues to each traffic class.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Each traffic class corresponds to a WQ priority level. The number of Tx
netdev queues and frame queues is increased to NR_CPUS queues for each
traffic class. In addition, the priority of the Rx, Error and Conf queues
is lowered but their order is maintained.
By default, only one traffic class is enabled, only the low priority Tx
queues are used and only the corresponding netdev queues are advertised.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
This commit adds the ndo_do_ioctl() callback which allows the userspace to
access PHY registers, for example. This will make mii-diag and similar
tools work.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake, en_tsu_err_exeption should
be en_tsu_err_exception
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be >= instead of > here. It means that we don't increment
the free count enough so it becomes off by one.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use an intermediate variable to handle an error code
in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
'of_node_put(fpi->phy_node)' should also be called if we branch to
'out_deregister_fixed_link' error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In spite of switching to paged allocation of Rx buffers, the driver still
called dma_unmap_single() in the Rx queues tear-down path.
The DMA region unmapping code in free_skb_rx_queue() basically predates
the introduction of paged allocation to the driver. While being refactored,
it apparently hasn't reflected the change in the DMA API usage by its
counterpart gfar_new_page().
As a result, setting an interface to the DOWN state now yields the following:
# ip link set eth2 down
fsl-gianfar ffe24000.ethernet: DMA-API: device driver frees DMA memory with wrong function [device address=0x000000001ecd0000] [size=40]
------------[ cut here ]------------
WARNING: CPU: 1 PID: 189 at lib/dma-debug.c:1123 check_unmap+0x8e0/0xa28
CPU: 1 PID: 189 Comm: ip Tainted: G O 4.9.5 #1
task: dee73400 task.stack: dede2000
NIP: c02101e8 LR: c02101e8 CTR: c0260d74
REGS: dede3bb0 TRAP: 0700 Tainted: G O (4.9.5)
MSR: 00021000 <CE,ME> CR: 28002222 XER: 00000000
GPR00: c02101e8 dede3c60 dee73400 000000b6 dfbd033c dfbd36c4 1f622000 dede2000
GPR08: 00000007 c05b1634 1f622000 00000000 22002484 100a9904 00000000 00000000
GPR16: 00000000 db4c849c 00000002 db4c8480 00000001 df142240 db4c84bc 00000000
GPR24: c0706148 c0700000 00029000 c07552e8 c07323b4 dede3cb8 c07605e0 db535540
NIP [c02101e8] check_unmap+0x8e0/0xa28
LR [c02101e8] check_unmap+0x8e0/0xa28
Call Trace:
[dede3c60] [c02101e8] check_unmap+0x8e0/0xa28 (unreliable)
[dede3cb0] [c02103b8] debug_dma_unmap_page+0x88/0x9c
[dede3d30] [c02dffbc] free_skb_resources+0x2c4/0x404
[dede3d80] [c02e39b4] gfar_close+0x24/0xc8
[dede3da0] [c0361550] __dev_close_many+0xa0/0xf8
[dede3dd0] [c03616f0] __dev_close+0x2c/0x4c
[dede3df0] [c036b1b8] __dev_change_flags+0xa0/0x174
[dede3e10] [c036b2ac] dev_change_flags+0x20/0x60
[dede3e30] [c03e130c] devinet_ioctl+0x540/0x824
[dede3e90] [c0347dcc] sock_ioctl+0x134/0x298
[dede3eb0] [c0111814] do_vfs_ioctl+0xac/0x854
[dede3f20] [c0111ffc] SyS_ioctl+0x40/0x74
[dede3f40] [c000f290] ret_from_syscall+0x0/0x3c
--- interrupt: c01 at 0xff45da0
LR = 0xff45cd0
Instruction dump:
811d001c 7c66482e 813d0020 9061000c 807f000c 5463103a 7cc6182e 3c60c052
386309ac 90c10008 4cc63182 4826b845 <0fe00000> 4bfffa60 3c80c052 388402c4
---[ end trace 695ae6d7ac1d0c47 ]---
Mapped at:
[<c02e22a8>] gfar_alloc_rx_buffs+0x178/0x248
[<c02e3ef0>] startup_gfar+0x368/0x570
[<c036aeb4>] __dev_open+0xdc/0x150
[<c036b1b8>] __dev_change_flags+0xa0/0x174
[<c036b2ac>] dev_change_flags+0x20/0x60
Even though the issue was discovered in 4.9 kernel, the code in question
is identical in the current net and net-next trees.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QBMan CGR options needs to be zeroed before calling the init
function
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fsl/fman drivers will use of_platform_populate() on all
supported platforms. Call of_platform_populate() to probe the
FMan sub-nodes.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
QSGMII ports were not advertising 1G speed.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
Ensure correct access to the big endian QMan HW through proper
accessors.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 407066f8f3 ("net: fec: Support phys probed from devicetree and
fixed-link")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
looking up a fixed-link phydev during probe.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() during
initialisation when later freeing the struct fman_mac.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on commit d8d2635419 ("ptp: Introduce a high
resolution frequency adjustment method.")
The gianfar devices offer a frequency resolution of about 0.46 ppb
(depends on actual value of tmr_add, for the calculation assumed
0x80000000). This patch lets users of the device benefit from the increased
frequency resolution when tuning the clock. Thanks to the rounding the
maximum error between the requested frequency and the applied frequency
will then be about 0.23 ppb.
Tested on a v3.3.8 kernel on a real gianfar device. Verified compilation
on net-next (currently at v4.9-rc5).
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We set "tgec->cfg" to NULL before passing it to kfree(). There is no
need to set it to NULL at all. Let's just delete it.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only a handful of Freescale Ethernet drivers that don't
actually build with COMPILE_TEST:
* FEC, for which we would need to define a default register layout if no
supported architecture is defined
* UCC_GETH which depends on PowerPC cpm.h header (which could be moved
to a generic location)
* GIANFAR needs to depend on HAS_DMA to fix linking failures on some
architectures (like m32r)
We need to fix an unmet dependency to get there though:
warning: (FSL_XGMAC_MDIO) selects OF_MDIO which has unmet direct
dependencies (OF && PHYLIB)
which would result in CONFIG_OF_MDIO=[ym] without CONFIG_OF to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FS is a global symbol used by the x86 32-bit architecture, fixes builds
re-definitions:
>> drivers/net/ethernet/freescale/gianfar_ptp.c:75:0: warning: "FS"
>> redefined
#define FS (1<<28) /* FIPER start indication */
In file included from arch/x86/include/uapi/asm/ptrace.h:5:0,
from arch/x86/include/asm/ptrace.h:6,
from arch/x86/include/asm/math_emu.h:4,
from arch/x86/include/asm/processor.h:11,
from include/linux/mutex.h:19,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:15,
from include/linux/kobject.h:21,
from include/linux/device.h:17,
from
drivers/net/ethernet/freescale/gianfar_ptp.c:23:
arch/x86/include/uapi/asm/ptrace-abi.h:15:0: note: this is the
location of the previous definition
#define FS 9
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add trace points on the hot processing path.
Signed-off-by: Ruxandra Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export Frame Queue and Buffer Pool IDs through sysfs.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a series of counters to be exported through ethtool:
- add detailed counters for reception errors;
- add detailed counters for QMan enqueue reject events;
- count the number of fragmented skbs received from the stack;
- count all frames received on the Tx confirmation path;
- add congestion group statistics;
- count the number of interrupts for each CPU.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces the Freescale Data Path Acceleration Architecture
(DPAA) Ethernet driver (dpaa_eth) that builds upon the DPAA QMan,
BMan, PAMU and FMan drivers to deliver Ethernet connectivity on
the Freescale DPAA QorIQ platforms.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ac72b7b63 ("net: fec: align IP header in hardware") breaks
networking on mx28.
There is an erratum on mx28 (ENGR121613 - ENET big endian mode
not compatible with ARM little endian) that requires an additional
byte-swap operation to workaround this problem.
So call swap_buffer() prior to performing the IP header alignment
to restore network functionality on mx28.
Fixes: 3ac72b7b63 ("net: fec: align IP header in hardware")
Reported-and-tested-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare, clk_enable and their counterparts (at least the common clk
ones, but also most others) do check for the clk being NULL anyhow (and
return 0 then), so there is no gain when the caller checks, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
fs_enet_private, use stats from struct net_device. Also remove the now
unnecessary .ndo_get_stats function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mac address origin is not dt, you can only safely assign a mac
address after "link up" of the device. If the link is off the clocks are
disabled and because of issues assigning registers when clocks are off the
new mac address cannot be written in .ndo_set_mac_address() on some soc's.
This fix sets the mac address unconditionally in fec_restart(...) and
ensures consistency between fec registers and the network layer.
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9638d19e48 ("net: fec: add netif status check before set mac address")
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd like to eventually remove NO_IRQ on powerpc, so remove usages of it
from powerpc-only drivers.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurement shows that on a MPC8xx running at 132MHz, the optimal
limit is 112:
* 114 bytes packets are processed in 147 TB ticks with higher copybreak
* 114 bytes packets are processed in 148 TB ticks with lower copybreak
* 128 bytes packets are processed in 154 TB ticks with higher copybreak
* 128 bytes packets are processed in 148 TB ticks with lower copybreak
* 238 bytes packets are processed in 172 TB ticks with higher copybreak
* 238 bytes packets are processed in 148 TB ticks with lower copybreak
However it might be different on other processors
and/or frequencies. So it is useful to make it configurable.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the length of the packet is below the defined copybreak limit,
the received packet is copied into a newly allocated skb in order
to reuse the skb. This is only interesting if it allow us to avoid
a new DMA mapping. We shall therefore not DMA unmap and remap the
skb->data. Instead, we invalidate the cache
with dma_sync_single_for_cpu() once the received data has been
copied into the new skb.
The following measures have been obtained on a mpc885 running at 132Mhz.
Measurement is done using the timebase with packets sent to the target
with 'ping -s 1' (packet len is 60):
* Without this patch: 182 TB ticks
* With this patch: 143 TB ticks
As a comparison, if we set the copybreak limit to 0, then we get
148 TB ticks. It means that without this patch, duration is even
worse when copying received data to a new skb instead of
allocating a new skb for next packet to be received
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially, a NAPI TX routine has been implemented separately from
NAPI RX, as done on the freescale/gianfar driver.
By merging NAPI RX and NAPI TX, we reduce the amount of TX completion
interrupts.
Handling of the budget in association with TX interrupts is based on
indications provided at https://wiki.linuxfoundation.org/networking/napi
We never proceed more than the complete TX ring on a single run.
At the same time, we fix an issue in the handling of fep->tx_free:
It is only when fep->tx_free goes up to MAX_SKB_FRAGS that
we need to wake up the queue. There is no need to call
netif_wake_queue() at every packet successfully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC register MRBLR defines the maximum space in
the RX buffers and is set to 1536 by gianfar. This
reasonably covers the common use case where the MTU
is kept at default 1500. In that case, the largest
Ethernet frame size of 1518 plus an optional
GMAC_FCB_LEN of 8, and an additional padding of 8
to handle FSL_GIANFAR_DEV_HAS_TIMER totals to 1534
and nicely fit within the chosen MRBLR.
Alas, if the eTSEC is attached to a DSA enabled switch,
the (E)DSA header extension (4 or 8 bytes) causes every
maximum sized frame to be fragmented by the hardware.
This patch increases the maximum RX buffer size by 8
and rounds up to the next multiple of 64, which the
hardware's defines as RX buffer granularity.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of leftover symbol conflicts caused by hashtable.h
being included by netdevice.h; those were not caught as build failure
(they're "only" a warning, but in fact real bugs). Fix those up.
Fixes: e87a8f24c ("net: resolve symbol conflicts with generic hashtable.h")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A patch series including both cpuidle and FEC driver changes to
disable deeper idle states when FEC is active while board level
workaround for ERR006687 is not available
- A number patches to fix sparse warnings and spell errors
- A fix for TZIC FIQ translation from VIRQ to HWIRQ
- Support compatible of i.MX7 Solo SoC which has a subset of i.MX7 Dual
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcmFTAAoJEFBXWFqHsHzOxXoH/A5B4yRv82dM9L6KcCYqxc8B
UL8Rt11mMsezj/mSoikPjdDV7rKRcbSyY7ujUs0g9jhdKzl2sCCu9rXtYN+oeDpH
iJrndyQ8+Y0UDitmvZGwyW5HImUKuoMvFjJpg7D3WGs/2wACj9TVrrNl+AWawZXR
B+mNO6vT3MEnflzFKkcZmYhwtMXPmaGDc732pS6sgqBLjAJp8X37wWoWJ2lVG9zf
8fjEfUcB3jqWFr6YYJk/adWEjFwRBQ1QayY994Cxeym9kSo3BXfDJ3wcnG1sdOvF
jsM0fsV75gMQNCy8VqiHTNhLk5DGM5PYKQLrQ8r0yoAwvXLLAbu+gPXJSWrACig=
=yWZX
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC changes for 4.8:
- A patch series including both cpuidle and FEC driver changes to
disable deeper idle states when FEC is active while board level
workaround for ERR006687 is not available
- A number patches to fix sparse warnings and spell errors
- A fix for TZIC FIQ translation from VIRQ to HWIRQ
- Support compatible of i.MX7 Solo SoC which has a subset of i.MX7 Dual
* tag 'imx-soc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: add support for i.MX 7Solo
ARM: i.MX: Disable supervisor protect for i.MX51
ARM: imx6: fix missing <soc/imx/cpuidle.h> in cpuidle-imx6q.c
ARM: i.MX: Fix FIQ interrupt handling for TZIC
ARM: imx6: fix static declaration in include/soc/imx/cpuidle.h
ARM: imx6q: export cpuidle functions needed by fec driver
ARM: imx: fix missing include of common.h
ARM: imx: fix missing includes
ARM: imx6: disable deeper idle states when FEC is active w/o HW workaround
ARM: mach-imx6q: fix spelling mistake in error message
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/ethernet/freescale/gianfar.c:2278:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
trivial fix to spelling mistakes and add missing newline in pr_err
messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit hardware timestamping is enabled, an additional
TxBD would be added and would be set as the last TxBD with TXBD_LAST
and TXBD_INTERRUPT. However this has been broken by a patch recently.
This made the software couldn't get transmit hardware timestamps and
resulted in call trace. So, this patch is to fix this issue.
Fixes: 48963b4492 ("gianfar: Remove redundant ops for do_tstamp
from xmit()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the one
contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.
The obvious fix is to only clear a queue's bit when the queue was
emptied.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fec_mpc52xx driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fs-enet driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the ucc driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the gianfar driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ethtool api {get|set}_settings is deprecated.
We move the fec driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 55cd48c821 ("net: fec: stop the "rcv is not +last, " error
messages") introduces a write to a register that does not exist in
Coldfire.
Move the FEC_FTRL register access inside the FEC_QUIRK_HAS_RACC 'if' block,
so that we guarantee it will not be used on Coldfire CPUs.
Reported-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata A-007273 (For FMan V3 devices only):
FMan soft reset is not finished properly if one
of the Ethernet MAC clocks is disabled
Workaround:
Re-enable all disabled MAC clocks through the DCFG_CCSR_DEVDISR2
register prior to issuing an FMAN soft reset.
Re-disable the MAC clocks after the FMAN soft reset is done.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug introduced in e06a03b (fsl/fman: fix the pause_time test)
When pause_time is set to '0' - pause frames are disabled and
there's no need to apply dTSEC-A003 Errata workaround.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
is actually "active high". Thanks for Troy Kisky for pointing
that out.
Since the patch is in linux-next, this patch is incremental and doesn't
replace the original patch.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable workaround for MPC8548E erratum eTSEC 106,
"Excess delays when transmitting TOE=1 large frames".
(see commit 53fad77375 "gianfar: Enable eTSEC-20 erratum w/a
for P2020 Rev1")
This erratum was fixed in Rev 3.1.x.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in a case of error, dev_err is using fman->dev
before its initialization and "(NULL device *)" is printed.
This patch fixes this issue.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix endianness for the 64-bit hardware timestamp value with
be64_to_cpu to support both PowerPC platforms and ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace get_of_u32 with standard helper function of_property_read_u32
since the latter can process cpu endianness.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timestamp BD status updates that can be merged into the
same "do_tstamp" block, no need for extra save/restore
to the BD area. The code is more readable too.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mapping of the head BD before the mapping of fragments.
The TOE (h/w offload) decision logic block can be also moved up
(as the TOE flag belongs to the head BD), resulting in more
localized code (TOE logic vs BD mapping code blocks).
Note that, for this h/w, the R (status) bit for the head BD of a S/G
frame needs to be written last for a reliable transmission.
For the fragmented skb case, a local variable is used to temporarily
store the status info of the first BD, replacing a BD status read.
A merge of 2 "if(do_tstamp)" blocks was also possible.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need that for a custom hardware that needs the reverse reset
sequence.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap initial buffer on error.
Don't free skb until it has been unmapped.
Move cbd_bufaddr assignment closer to the mapping function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you don't own it, you shouldn't write to it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the interrupt routine processes this condition.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex macros every time we need to activate
a queue. Also, no need to call skb_get_queue_mapping when we already
know which queue it is using.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When first initialized, cur_tx points to the 1st
entry in the queue, and dirty_tx points to the last.
At this point, fec_enet_get_free_txdesc_num will
return tx_ring_size -2. If tx_ring_size -2 entries
are now queued, then fec_enet_get_free_txdesc_num
should return 0, but it returns tx_ring_size instead.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an overrun, the other flags are not
valid, so don't check them.
Also, don't pass bad frames up the stack.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the FTRL register will stop the fec from
trying to use multiple receive buffers.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnd Bergmann points out, using CONFIG_ARCH_MXC and/or SOC_IMX28
is wrong if some other ARM platform uses this device - the operation
of the driver would depend on an unrelated ARM platform that might
or might not be set for multi-platform kernels.
Prior to my previous patch, any other platforms using it would have
been broken already due to having the cbd_datlen/cbd_sc fields in
the wrong order, but byte ordering correctly, so no such platforms
can exist and work today.
In any case, it seems likely that only Freescale SoCs use this part,
and those are little-endian on ARM, so CONFIG_ARM is safe for them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver treats the device descriptors as CPU-endian, which appears
to be correct with the default endianness on both ARM (typically LE)
and PowerPC (typically BE) SoCs, indicating that the hardware block
is generated differently. Add endianness annotations and byteswaps as
necessary.
It's not clear that the ifdef there really is correct and shouldn't
just be #ifdef CONFIG_ARM, but I also can't test on anything but the
i.MX6 HummingBoard where this gets it working with a BE kernel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an additional patch to the one already submitted recently.
The previous patch was not complete, and the FCC port lock-up scenario
has been reproduced in lab.
I had an opportunity to check the current patch in lab and the FCC
port lock no longer freezes, while the previous patch still locks-up the
FCC port.
The current patch fixes a pointer arithmetic bug (second bug in the same
line), which leads FCC port lock-up during underrun/collision handling.
Within the tx_startup() function in mac-fcc.c, the address of last BD is
not calculated correctly. As a result of wrong calculation of the last BD
address, the next transmitted BD may be set to an area out of the transmit
BD ring. This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A quick set of bug fixes after there initial networking merge:
1) Netlink multicast group storage allocator only was tested with
nr_groups equal to 1, make it work for other values too. From
Matti Vaittinen.
2) Check build_skb() return value in macb and hip04_eth drivers, from
Weidong Wang.
3) Don't leak x25_asy on x25_asy_open() failure.
4) More DMA map/unmap fixes in 3c59x from Neil Horman.
5) Don't clobber IP skb control block during GSO segmentation, from
Konstantin Khlebnikov.
6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.
7) Fix SKB segment utilization estimation in xen-netback, from David
Vrabel.
8) Fix lockdep splat in bridge addrlist handling, from Nikolay
Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
bgmac: Fix reversed test of build_skb() return value.
bridge: fix lockdep addr_list_lock false positive splat
net: smsc: Add support h8300
xen-netback: free queues after freeing the net device
xen-netback: delete NAPI instance when queue fails to initialize
xen-netback: use skb to determine number of required guest Rx requests
net: sctp: Move sequence start handling into sctp_transport_get_idx()
ipv6: update skb->csum when CE mark is propagated
net: phy: turn carrier off on phy attach
net: macb: clear interrupts when disabling them
sctp: support to lookup with ep+paddr in transport rhashtable
net: hns: fixes no syscon error when init mdio
dts: hisi: fixes no syscon fault when init mdio
net: preserve IP control block during GSO segmentation
fsl/fman: Delete one function call "put_device" in dtsec_config()
hip04_eth: fix missing error handle for build_skb failed
3c59x: fix another page map/single unmap imbalance
3c59x: balance page maps and unmaps
x25_asy: Free x25_asy on x25_asy_open() failure.
mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
...
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
The Coccinelle semantic patch script "deref_null.cocci" pointed a problem
out in the implementation of the function "dtsec_config".
A null pointer was assigned to the data structure member "tbiphy" of the
variable "dtsec" if a matching device was not found.
A call of the function "put_device" was unnecessary then because
a previous call of the function "get_device" was not triggered.
Thus remove the function call "put_device" after the printing of the
desired error message.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
"priv" is allocated with devm_kzalloc() so freeing it here with kfree()
will lead to a double free.
Fixes: 3933961682 ('fsl/fman: Add FMan MAC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pause_time is unsigned so it can't be less than zero. The bug means
that we allow invalid pause-times.
Fixes: 57ba4c9b56 ('fsl/fman: Add FMan MAC support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM allmodconfig fails because of the addition of the FMAN driver:
drivers/built-in.o: In function `dtsec_restart_autoneg':
binder.c:(.text+0x173328): undefined reference to `mdiobus_read'
binder.c:(.text+0x173348): undefined reference to `mdiobus_write'
drivers/built-in.o: In function `dtsec_config':
binder.c:(.text+0x173d24): undefined reference to `of_phy_find_device'
drivers/built-in.o: In function `init_phy':
binder.c:(.text+0x1763b0): undefined reference to `of_phy_connect'
drivers/built-in.o: In function `stop':
binder.c:(.text+0x176014): undefined reference to `phy_stop'
drivers/built-in.o: In function `start':
binder.c:(.text+0x176078): undefined reference to `phy_start'
The reason is that the driver uses PHYLIB, but that is a loadable
module here, and fman itself is built-in.
This patch makes it possible to configure fman as a module as well
so we don't change the status of PHYLIB in an allmodconfig kernel,
and it adds a 'select PHYLIB' statement to ensure that phylib is
always built-in when fman is.
The driver uses "builtin_platform_driver(fman_driver);", which means
it cannot be unloaded, but it's still possible to have it as a loadable
module that gets loaded once and never removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5adae51a64 ("fsl/fman: Add FMan MURAM support")
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Ethernet MAC driver supporting the three
different types of MACs: dTSEC, tGEC and mEMAC.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Data Path Acceleration Architecture Frame Manger Port Driver.
The FMan driver uses a module called "Port" to represent the physical
TX and RX ports.
Each FMan version has different number of physical ports.
This patch adds The FMan Port configuration, initialization and
runtime control routines for both TX and RX.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Storage Profiles contain parameters that are used
by the FMan for frame reception and transmission.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Data Path Acceleration Architecture Frame Manger MAC support.
This patch adds The FMan MAC configuration, initialization and
runtime control routines.
This patch contains support for these types of MACs:
- dTSEC: Three speed Ethernet controller (10/100/1000 Mbps)
- tGEC: 10G Ethernet controller (10 Gbps)
- mEMAC: Multi-rate Ethernet MAC (10/100/1000/10000 Mbps)
Different FMan revisions have different type and number of MACs.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Data Path Acceleration Architecture Frame Manger Driver.
The FMan embeds a series of hardware blocks that implement a group
of Ethernet interfaces. This patch adds The FMan configuration,
initialization and runtime control routines.
The FMan driver supports several hardware versions
differentiated by things like:
- Different type of MACs
- Number of MAC and ports
- Available resources
- Different hardware errata
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Frame Manager Multi-User RAM support.
This internal FMan memory block is used by the
FMan hardware modules, the management being made
through the generic allocator.
The FMan Internal memory, for example, is used for
allocating transmit and receive FIFOs.
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes FCC port lock-up, which occurs as a result of a bug
during underrun/collision handling. Within the tx_startup() function
in mac-fcc.c, the address of last BD is not calculated correctly.
As a result of wrong calculation of the last BD address, the next
transmitted BD may be set to an area out of the transmit BD ring.
This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the
Parser"), 'TSEC' model controllers (for example as seen on MPC8541E)
always have 8 bytes stripped from the front of received frames.
Only 'eTSEC' gianfar controllers have the RX Filer capability (amongst
other enhancements). Previously this was treated as always enabled
for both 'TSEC' and 'eTSEC' controllers.
In commit 15bf176db1 ("gianfar: Don't enable the Filer w/o the Parser")
a subtle change was made to the setting of 'uses_rxfcb' to effectively
always set it (since 'rx_filer_enable' was always true). This had the
side-effect of always stripping 8 bytes from the front of received frames
on 'TSEC' type controllers.
We now only enable the RX Filer capability on controller types that
support it, thereby avoiding the issue for 'TSEC' type controllers.
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb90 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gianfar driver has recently been enabled on arm64 but fails to build
since it check the return value of platform_get_irq() against NO_IRQ. Fix
this by instead checking for a negative error code.
Even on ARM where this code was previously being built this check was
incorrect since platform_get_irq() returns a negative error code which
may not be exactly the (unsigned int)(-1) that NO_IRQ is defined to be.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can be built on arm64 but relies on NO_IRQ to check the return
value of irq_of_parse_and_map() which fails to build on arm64 because the
architecture does not provide a NO_IRQ. Fix this to correctly check the
return value of irq_of_parse_and_map().
Even on ARM systems where the driver was previously used the check was
broken since on ARM NO_IRQ is -1 but irq_of_parse_and_map() returns 0 on
error.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in case of error no need to set num_tx and num_rx = 1, because in case of error
these variables will remain unchanged by of_property_read_u32 ie 1 only
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale hosts some ARMv8 based SoCs, and a generic convention
ARCH_LAYERSCAPE is used to cover such SoCs. Adding ARCH_LAYERSCAPE
to dependencies of NET_VENDOR_FREESCALE to support networking on those
SoCs.
The ARCH_LAYERSCAPE is introduced by:
commit: 53a5fde05 arm64: Use generic Layerscape SoC family naming
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use of_property_read_bool() for testing bool property
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
We are in a context where we can sleep, and the FEC PHY reset gpio
may be on an I2C expander. Use the cansleep() variant when
setting the GPIO value.
Based on a patch from Russell King for pci-mvebu.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx BSY error interrupt indicates that a frame was
received and discarded due to lack of buffers, so it's
a rx ring overflow condition and has nothing to do with
with bad rx packets. Use the right counter.
BSY conditions happen when the SoC is under performance
stress. Doing *more* work in stress situations by trying
to schedule NAPI is not a good idea as the stressed system
becomes still more stressed. The Rx interrupt is already
at work making sure the NAPI is scheduled.
So calling gfar_receive() here does not help. This issue
was present since day 1.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under one unusual circumstance it's possible to wrongly set
FILREN without enabling PRSDEP as well in the RCTRL register,
against the hardware specifications. With the default config
this does not happen because the default Rx offloads (Rx csum
and Rx VLAN) properly enable PRSDEP. But if anyone disables
all these offloads (via ethtool), we get a wrong configuration
were the Rx flow classification and hashing, and other Filer
based features (e.g. wake-on-filer interrupt) won't work.
This patch fixes the issue.
Also, account for Rx FCB insertion which happens every time
PRSDEP is set.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RQFCR_AND is duplicated.
Add missing space as well.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit afae5ad78b
"net/fsl_pq_mdio: streamline probing of MDIO nodes"
added support for different types of MDIO devices:
1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)
However, the implementation for types 1 and 4 would mistakenly assume
a mapping of the full MDIO register set, thereby computing the address
for the TBI register starting from the containing structure.
The TBI register would therefore be accessed at a wrong (much bigger)
address, not giving the expected result at all.
This patch restores the correct behavior we had prior to the above one.
The consequences of this bug are apparent when trying to access a PHY
with the same address as the value contained in the initial value of
the TBI register (normally 0); in that case you'll get answers from the
internal TBI device (even though MDIO/MDC pins are actually *also*
toggling on the physical bus!).
Beware that you also need to add a fake tbi node to your device tree
with an unused address.
Notice how this fix is related to commit
220669495b
"powerpc: Add TBI PHY node to first MDIO bus"
which fixed the behavior in kernel 3.3, which was later broken by the
above commit on kernel 3.7.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the MDIO subsystem it is also necessary to configure
the TBI register. Make sure the TBI is contained within the mapped
register range in order to:
a) make sure the address is computed correctly
b) make users aware that we're actually accessing that register
In case of error, print a message but continue anyway.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Timur Tabi <timur@tabi.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables eTSEC's filer (Rx parser) and the FGPI Rx
interrupt (Filer General Purpose Interrupt) as a wakeup
source event.
Upon entering suspend state, the eTSEC filer is given
a rule to match incoming L2 unicast packets. A packet
matching the rule will be enqueued in the Rx ring and
a FGPI Rx interrupt will be asserted by the filer to
wakeup the system. Other packet types will be dropped.
On resume the filer table is restored to the content
before entering suspend state.
The set of rules from gfar_filer_config_wol() could be
extended to implement other WoL capabilities as well.
The "fsl,wake-on-filer" DT binding enables this capability
on certain platforms that feature the necessary power
management infrastructure, targeting mainly printing and
imaging applications.
(refer to Power Management section of the SoC Ref Man)
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fec_ptp_enable_pps uses an open-coded implementation of ns_to_timespec,
which will be removed eventually as it is not y2038-safe on 32-bit
architectures. Two more instances of the same code in this file were
already converted to use the safe ns_to_timespec64 in commit 6630514fce
("ptp: fec: use helpers for converting ns to timespec"), this changes
the last one as well.
The seconds portion here is actually unused and we could just remove the
timespec variable, but using ns_to_timespec64 can still be better as the
implementation can be hand-optimized in the future.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Fugang Duan <b38611@freescale.com>
Cc: Luwei Zhou <b45643@freescale.com>
Cc: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have FEATURES_NEED_QUIESCE defined as we
can simply use NETIF_F_RXCSUM instead as done in other parts
of the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() increments the phy struct device refcount, which
we need to properly balance. Add code to network drivers using this
function to ensure that the struct device refcount is correctly
balanced.
For xgene, looking back in the history, we should be able to use
of_phy_connect() with a zero flags argument for the DT case as this is
how the driver used to operate prior to de7b5b3d79 ("net: eth: xgene:
change APM X-Gene SoC platform ethernet to support ACPI").
This leaves the Cavium Thunder BGX unfixed; fixing this driver is a
complicated task, one which the maintainers need to be involved with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist one issue by below case that case system hang:
ifconfig eth0 down
ifconfig eth0 hw ether 00:10:19:19:81:19
After eth0 down, all fec clocks are gated off. In the .fec_set_mac_address()
function, it will set new MAC address to registers, which causes system hang.
So it needs to add netif status check to avoid registers access when clocks are
gated off. Until eth0 up the new MAC address are wrote into related registers.
V2:
As Lucas Stach's suggestion, add a comment in the code to explain why it needed.
CC: Lucas Stach <l.stach@pengutronix.de>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fec MDIO write method succeeds its return value comes from
call to pm_runtime_get_sync().
But pm_runtime_get_sync() can also return 1.
In case of Micrel KSZ9031 PHY this value will then
be returned along the call chain of phy_write() ->
ksz9031_extended_write() -> ksz9031_center_flp_timing() ->
ksz9031_config_init() -> phy_init_hw() -> phy_attach_direct() ->
phy_connect_direct().
Then phy_connect() will cast it into a pointer using ERR_PTR(),
which then fec_enet_mii_probe() will try to dereference
resulting in an oops.
Fix it by normalizing return value of pm_runtime_get_sync()
to be zero if positive in MDIO write method.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch just to re-submit the patch "db3421c114cfa6326" because the
patch "4d494cdc92b3b9a0" remove the change.
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some MAC registers that need to be kept in sync
with the link state parameters, see adjust_link().
However, after a MAC soft reset default values for
these registers are assumed. In some cases (excepting
if down/ if up for example) adjust_link() does not see
that these values were reset to default because the
priv->old* link parameters were left unchanged.
So, reset the priv->old* link params as well during a
MAC reset to let adjust_link() restore the MAC link
settings to the actual link state values.
Fixes following case, for example:
Setting link to 100M, changing MTU (implies MAC reset),
link state remains unchanged to 100M but MAC registers
were reset to default (1G) breaking the connectivity w/
the PHY. Closing and re-opening the interface would
restore the MAC link parameters to the correct values.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clocks are initially active and thus the device is marked active.
This still keeps the PM refcount at 0, the pm_runtime_put_autosuspend()
call at the end of probe then leaves us with an invalid refcount of -1,
which in turn leads to the device staying in suspended state even though
netdev open had been called.
Fix this by initializing the refcount to be coherent with the initial
device status.
Fixes:
8fff755e9f (net: fec: Ensure clocks are enabled while using mdio bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
