of_dma_configure is called by the core before probe gets called so this
is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the MBUS quirks are applied by our global notifier, we can
remove them from our CSI driver for the A31.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the MBUS quirks are applied by our global notifier, we can
remove them from our CSI driver for the A10.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the items in the TODO list were addressed, uapi was reviewed,
documentation written, checkpatch errors fixed, several bugs fixed.
There is no big reason to keep this driver in staging, so move it out.
Dt-bindings Verified with:
make ARCH=arm64 dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/rockchip-isp1.yaml
Fields of MAINTAINERS file sorted according to output of
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
--order
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[hverkuil: fix various checkpatch alignment warnings]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the SMMU translation is disabled in the
arm-smmu shutdown callback during reboot, if
any subsystem are still alive then IOVAs they
are using will become PAs on bus, which may
lead to crash.
So implemented shutdown callback, which detach iommu maps.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In concurrency usecase and reboot scenario we are seeing muliple
crashes related to iommu_map/iommu_unamp of core->fw.iommu_domain.
In one case we are seeing "Unable to handle kernel NULL pointer
dereference at virtual address 0000000000000008" crash, this is
because of core->fw.iommu_domain in venus_firmware_deinit() and
trying to map in venus_boot() during venus_sys_error_handler()
Call trace:
__iommu_map+0x4c/0x348
iommu_map+0x5c/0x70
venus_boot+0x184/0x230 [venus_core]
venus_sys_error_handler+0xa0/0x14c [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
In second case we are seeing "Unable to handle kernel paging request
at virtual address 006b6b6b6b6b6b9b" crash, this is because of
unmapping iommu domain which is already unmapped.
Call trace:
venus_remove+0xf8/0x108 [venus_core]
venus_core_shutdown+0x1c/0x34 [venus_core]
platform_drv_shutdown+0x28/0x34
device_shutdown+0x154/0x1fc
kernel_restart_prepare+0x40/0x4c
kernel_restart+0x1c/0x64
__arm64_sys_reboot+0x190/0x238
el0_svc_common+0xa4/0x154
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x10
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For core ops we are having only write protect but there
is no read protect, because of this in multithreading
and concurrency, one CPU core is reading without wait
which is causing the NULL pointer dereferece crash.
one such scenario is as show below, where in one CPU
core, core->ops becoming NULL and in another CPU core
calling core->ops->session_init().
CPU: core-7:
Call trace:
hfi_session_init+0x180/0x1dc [venus_core]
vdec_queue_setup+0x9c/0x364 [venus_dec]
vb2_core_reqbufs+0x1e4/0x368 [videobuf2_common]
vb2_reqbufs+0x4c/0x64 [videobuf2_v4l2]
v4l2_m2m_reqbufs+0x50/0x84 [v4l2_mem2mem]
v4l2_m2m_ioctl_reqbufs+0x2c/0x38 [v4l2_mem2mem]
v4l_reqbufs+0x4c/0x5c
__video_do_ioctl+0x2b0/0x39c
CPU: core-0:
Call trace:
venus_shutdown+0x98/0xfc [venus_core]
venus_sys_error_handler+0x64/0x148 [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently in calculate_inst_freq(), video driver is calculating
macro blocks per frame instead of macro blocks per second(mpbs).
Which results frequency is always setting to lower frequency (150MHz)
as per frequency table for sc7180. Hence the playback is not smooth.
Corrected this by correcting the mbps calculation in calculate_inst_freq().
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per current implementation, video driver is unvoting "videom-mem" path
for last video session during vdec_session_release().
While video playback when we try to suspend device, we see video clock
warnings since votes are already removed during vdec_session_release().
corrected this by putting dummy vote on "video-mem" after last video
session release and unvoting it during suspend.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per bandwidth table video driver is voting with average bandwidth
for "video-mem" and "cpu-cfg" paths as peak bandwidth is zero
in bandwidth table.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently video driver is voting for venus0-ebi path during buffer
processing with an average bandwidth of all the instances and
unvoting during session release.
While video streaming when we try to do XO-SD using the command
"echo mem > /sys/power/state command" , device is not entering
to suspend state and from interconnect summary seeing votes for venus0-ebi
Corrected this by voting for venus0-ebi path in venus_runtime_resume()
and unvote during venus_runtime_suspend().
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently video driver is voting after clk enable and un voting
before clk disable. This is incorrect, video driver should vote
before clk enable and unvote after clk disable.
Corrected this by changing the order of clk enable and clk disable.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Per the stateful codec specification, VIDIOC_G_SELECTION with a target
of V4L2_SEL_TGT_COMPOSE is supposed to return the crop area of capture
buffers containing the decoded frame. Until now the driver did not get
that information from the firmware and just returned the dimensions of
CAPTURE buffers.
The firmware unfortunately does not always provide the crop information
from the stream ; also make sure to detect when that happens and
fallback to providing the coded size in these cases.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The default codec after driver open is set to be H264 but the
instance format for capture is wrongly set to H263. Correct this
to H264.
For regular applications this is not a big issue because they set
the format through S_FMT but for example v4l2-compliance does not.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The profile and level in op_set_ctrl was recently changed but during
v4l2_ctrl_handler_setup profile and level control values are mangled.
Fixes: 435c53c369 ("media: venus: venc: Use helper to set profile and level")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if mtk_jpeg_clk_init() succeed, mtk_jpeg_probe() and mtk_jpeg_remove()
doesn't have a corresponding put_device(). Thus add a new helper
mtk_jpeg_clk_release() to fix it.
Fixes: b2f0d2724b ("[media] vcodec: mediatek: Add Mediatek JPEG Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To avoid potentially overflowing the kernel logs in the case
of corrupted streams, this commit replaces an error message with
a per-stream counter to be read through a driver-specific
control.
Applications can read the per-stream accumulated
error macroblocks count.
The old error message is replaced by a rate-limited debug message.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's possible that the VPU was initialized using just one buffer,
containing only codec headers.
In this case, right after the initialization and after updating
the FIFO read pointer, we need to iterate through all the coda_buffer_meta
and release any metas that have been already used by the VPU.
This issue is affecting indirectly the bitstream buffer fill
threshold, which depends on the meta end position of the first
queued meta, which is passed to coda_bitstream_can_fetch_past().
Without this fix, it's possible that for certain videos, the
bitstream buffer level is not filled properly, resulting in a PIC_RUN
timeout.
Reported-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 9495b7e92f ("driver core: platform: Initialize dma_parms for
platform devices") included dma_parms in platform_device. There's no need
to allocate again.
Fixes: 13483fc2f2 ("media: mtk-vcodec: set dma max segment size")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
isif_probe() invokes iounmap() on error handling paths, but it does not
reset the global state. So, later it can invoke iounmap() even when
ioremap() fails. This is the case also for isif_remove(). The patch
resets the global state after invoking iounmap() to avoid this.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace dmaengine_terminate_all() by dmaengine_terminate_sync()
to ensure that all pending dma operations are really finished.
This is not ensured by dmaengine_terminate_all() and this API
is deprecated, so better to use the _sync() variant.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Philippe CORNU <philippe.cornu@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only supported bus for the R-Car CSI-2 driver is CSI-2 DPHY, specify
this before parsing the fwnode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the fwnode_graph_get_endpoint_by_id() interface instead of
of_graph_get_endpoint_by_regs() to fetch the fwnode. This saves
translating between a device_node and fwnode_handle.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for suspend and resume by stopping and starting the video
pipeline while still retaining all buffers given to the driver by
user-space and internally allocated ones, this gives the application a
seamless experience.
Buffers are never returned to user-space unprocessed so user-space don't
notice when suspending. When resuming the driver restarts the capture
session using the internal scratch buffer, this happens before
user-space is unfrozen, this leads to speedy response times once the
application resumes its execution.
As the entire pipeline is stopped on suspend all subdevices in use are
also stopped, and if they enter a shutdown state when not streaming
(such as the R-Car CSI-2 driver) they too will be suspended and resumed
in sync with the VIN driver.
To be able to do keep track of which VINs should be resumed a new
internal state SUSPENDED is added to recode this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To support suspend and resume the ability to start and stop the hardware
needs to be available internally in the driver. Currently this code is
in the start and stop callbacks of the vb2_ops struct. In these
callbacks the code is intertwined with buffer allocation and freeing.
Prepare for suspend and resume support by breaking out the hardware
start/stop code into new methods.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of suspend/resume support cache the chsel value when
written to the register so it can be restored on resume if needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When returning buffers to user-space it's no longer needed to examine
the buffers given to hardware as recent changes guarantees the only
buffer present in the hardware registers when the driver is not in the
running state is the scratch buffer.
Remove the special case and rename the function to better describe it
now only deals with buffers queued to the driver but not yet recorded in
the hardware registers.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In its early stages the VIN driver did not use an internal scratch
buffer. This leads to a unnecessary complex start and stop behavior,
specially for TB/BT. The driver now always allocates a scratch buffer to
deal with buffer under-runs, use the scratch buffer to also simplify
starting and stopping.
When capture is starting use the scratch buffer instead of a user-space
buffers while syncing the driver with the hardware state. This allows
the driver to know that no user-space buffer is given to the hardware
before the running state is reached.
When capture is stopping use the scratch buffer instead of leaving the
user-space buffers in place and add a check that all user-space buffers
are processed by the hardware before transitioning from the stopping to
stopped state. This allows the driver to know all user-space buffers
given to the hardware are fully processed.
This change in itself does not improve the driver much but it paves the
way for future simplifications and enhancements. One direct improvement
of this change is that TB/BT buffers returned to user-space while stopping
will always contain both fields, that was not guaranteed before.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
None of these BUG_ON()'s is justified. BUG_ON() should only be used when
there is really no way to survive.
If at all these could be replaced by lockdep_assert_preemption_enabled() to
cover all invalid caller context and not just those covered by
in_interrupt().
But all functions which are invoked from those places contain already debug
mechanisms to catch wrong context, so having these extra checks is not
having any advantage.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_vcodec_release_enc_pm() will be called in two places:
a. mtk_vcodec_init_enc_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_enc_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_enc_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_enc_pm()
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeed, mtk_vcodec_init_enc_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 4e855a6efa ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_vcodec_release_dec_pm() will be called in two places:
a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_dec_pm()
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeed, mtk_vcodec_init_dec_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeeds, mtk_jpeg_clk_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 648372a87c ("media: platform: Change the call functions of getting/enable/disable the jpeg's clock")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make interrupt naming more consistent by using a common
pattern for video and jpeg interrupts.
With this commit, interrupts are shown as:
29: 0 0 GPC 12 Level coda-video
30: 0 0 GPC 3 Level coda-jpeg
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of printing just the device type, let's use
the device name, which makes the message more useful.
With this commit, the messages shown when the driver
is registered are:
coda 2040000.vpu: Firmware code revision: 570363
coda 2040000.vpu: Initialized CODA960.
coda 2040000.vpu: Firmware version: 3.1.1
coda 2040000.vpu: coda-jpeg-encoder registered as video0
coda 2040000.vpu: coda-jpeg-decoder registered as video1
coda 2040000.vpu: coda-video-encoder registered as video2
coda 2040000.vpu: coda-video-decoder registered as video3
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The H.264 small buffer padding is done under
the (ctx->qsequence == 0 && payload < 512) condition.
Given this is the exact same condition immediately
above, we can move it right there, making the code
slightly clearer.
This change shouldn't affect functionality as it's just
cosmetics.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ctx->initialized flag is set in __coda_decoder_seq_init,
so it's redundant to set it in coda_dec_seq_init_work.
Remove the redundant set, which allows to simplify the
implementation quite a bit.
This change shouldn't affect functionality as it's just
cosmetics.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mandatory compatible value 'renesas,rcar-gen2-vin' was added to all
Gen2 DTS files in 2017, remove the redundant device specific values from
the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If CONFIG_PM is n, gcc warns:
drivers/media/platform/marvell-ccic/mmp-driver.c:324:12: warning: ‘mmpcam_runtime_suspend’ defined but not used [-Wunused-function]
static int mmpcam_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/marvell-ccic/mmp-driver.c:310:12: warning: ‘mmpcam_runtime_resume’ defined but not used [-Wunused-function]
static int mmpcam_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
Mark them as __maybe_unused to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix build warnings when CONFIG_PM is not set/enabled:
../drivers/media/platform/marvell-ccic/mmp-driver.c:324:12: warning: 'mmpcam_runtime_suspend' defined but not used [-Wunused-function]
324 | static int mmpcam_runtime_suspend(struct device *dev)
../drivers/media/platform/marvell-ccic/mmp-driver.c:310:12: warning: 'mmpcam_runtime_resume' defined but not used [-Wunused-function]
310 | static int mmpcam_runtime_resume(struct device *dev)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The addition of MT8183 support added a dependency on the SCP remoteproc
module. However the initial patch used the "select" Kconfig directive,
which may result in the SCP module to not be compiled if remoteproc was
disabled. In such a case, mtk-vcodec would try to link against
non-existent SCP symbols. "select" was clearly misused here as explained
in kconfig-language.txt.
Replace this by a "depends" directive on at least one of the VPU and
SCP modules, to allow the driver to be compiled as long as one of these
is enabled, and adapt the code to support this new scenario.
Also adapt the Kconfig text to explain the extra requirements for MT8173
and MT8183.
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk-vcodec supports two kinds of firmware, VPU and SCP. Both were
supported from the same source files, but this is clearly unclean and
makes it more difficult to disable support for one or the other.
Move these implementations into their own file, after adding the
necessary private interfaces.
[hverkuil: smatch fix: mtk_vcodec_fw_vpu_init() error: uninitialized symbol 'rst_id'.]
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
pixelformat in vin priv structure holds V4L2_PIX_FMT_* and not
MEDIA_BUS_FMT_* so make sure we check against V4L2_PIX_FMT_* formats
while setting the VNIS_REG.
Fixes: 8c3e0f67df ("media: rcar-vin: Extend RAW8 support to all RGB layouts")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Merge dma-contiguous.h into dma-map-ops.h, after removing the comment
describing the contiguous allocator into kernel/dma/contigous.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add proper control type to the recently introduced
V4L2_CID_MPEG_VIDEO_FRAME_SKIP_MODE control. This will forward it to
v4l2_ctrl_new_std_menu() not v4l2_ctrl_new_std(), what causes the
failure. This fixes the following warning during driver initialization:
s5p_mfc_enc_ctrls_setup:2671: Adding control (18) failed
s5p_mfc_open:811: Failed to setup mfc controls
Fixes: ef56b3ee4f ("media: s5p-mfc: Use standard frame skip mode control")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the list of supported formats to include all RGB layouts of RAW8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the list of supported formats to include all RGB layouts of RAW8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
delta_run_work() calls delta_get_sync() that increments
the reference counter. In case of failure, decrement the reference
count by calling delta_put_autosuspend().
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
And also, when the call of function vpe_runtime_get() failed,
we won't call vpe_runtime_put().
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails
inside vpe_runtime_get().
Fixes: 4571912743 ("[media] v4l: ti-vpe: Add VPE mem to mem driver")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not
called in error handling paths. Thus replace the jump target
"err_release_buffers" by "err_pm_putw".
Fixes: 152e0bf602 ("media: stm32-dcmi: add power saving support")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Fixes: c5086f130a ("[media] s5p-mfc: Use clock gating only on MFC v5 hardware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
PM runtime put is not called in error handling paths.
Thus call pm_runtime_put_sync() if pm_runtime_get_sync() fails.
Fixes: 02afa816db ("media: camss: Add basic runtime PM support")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Fixes: 6eaafbdb66 ("[media] v4l: rcar-fcp: Keep the coding style consistent")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus call pm_runtime_put_noidle()
if pm_runtime_get_sync() fails.
Fixes: 2a18fbec1d ("media: rcar-vin: Move pm_runtime_{get,put} out of helpers")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus call pm_runtime_put_noidle()
if pm_runtime_get_sync() fails.
Fixes: 90dedce9bc ("media: rcar-vin: add function to manipulate Gen3 chsel value")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When coda_firmware_request() returns an error code,
a pairing runtime PM usage counter decrement is needed
to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Also, call pm_runtime_disable() when pm_runtime_get_sync() returns
an error code.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable YDS bit if bus_width and data_shift is set to 8 in parallel mode
for MEDIA_BUS_FMT_UYVY8_2X8 format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the SoC specific information for RZ/G2H (R8A774E1) SoC. Also add
the routing information between CSI2 and VIN (which is similar to
R-Car H3 except it lacks CSI41).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2H (R8A774E1) SoC.
The CSI-2 module of RZ/G2H is similar to R-Car H3.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rcar-fcp driver is also used on Renesas RZ/G2 SoCs. Update the
Kconfig entry description to reflect this.
[hverkuil: incorporated Laurent's suggestions for subject and commit log]
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The suspend/resume functions have no callers depending on
configuration, so they must be marked __maybe_unused to
avoid these harmless warnings:
drivers/media/platform/marvell-ccic/mmp-driver.c:347:12: warning:
'mmpcam_resume' defined but not used [-Wunused-function]
347 | static int mmpcam_resume(struct device *dev)
| ^~~~~~~~~~~~~
drivers/media/platform/marvell-ccic/mmp-driver.c:338:12: warning:
'mmpcam_suspend' defined but not used [-Wunused-function]
338 | static int mmpcam_suspend(struct device *dev)
| ^~~~~~~~~~~~~~
Fixes: 55cd34524a ("media: marvell-ccic: add support for runtime PM")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When platform_get_irq() fails, we should release
vfd and unregister pcdev->v4l2_dev just like the
subsequent error paths.
Fixes: d4e192cc44 ("media: mx2_emmaprp: Check for platform_get_irq() error")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver requests IRQs to disable them immediately. This is
potentially racy, fix this by requesting the IRQs to come disabled
instead using the IRQ_NOAUTOEN flag of irq_set_status_flags().
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2-compliance expects the driver to adjust the time per frame if it is
invalid (numerator or denominator set to 0). Adjust it to the default
value in these cases.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The time per frame was left initialized to 0/0, which make the driver
fail v4l2-compliance, and also leaves it potentially exposed to doing a
division by zero.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2-compliance requires ENUM_FRAMESIZES to support OUTPUT formats.
Reuse mtk_venc_find_format() to make sure both queues are considered
when serving an ENUM_FRAMESIZES.
[hverkuil: fixed some checkpatch alignment warnings]
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vidioc_enum_framesizes() assumes that all encoders support H.264 and VP8,
which is not necessarily true and requires to duplicate information about
the supported codecs which is already stored in the platform data.
Fix this by referring to the platform data to find out whether a given
format is supported. Since the supported sizes are all the same
regardless of the format, we can then return a copy of a static value if
the format is supported.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A default value of 0 means V4L2_FIELD_ANY, which is not correct.
Reported by v4l2-compliance.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This control is required by v4l2-compliance for encoders. A value of 1
should be suitable for all scenarios.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit 81735ecb62.
The hardware needs data to follow the previous alignment, so this extra
space was not superfluous after all. Besides, this also made
v4l2-compliance's G_FMT and S_FMT tests regress.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that all the supporting blocks are present, enable encoder for
MT8183.
[acourbot: refactor, cleanup and split]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Different chips have different supported formats. Move the list of
supported formats to the platform data, and split the output and capture
formats into two lists to make it easier to find the default format for
each queue.
[hverkuil: fixed some checkpatch alignment warnings]
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Different chips have different supported bitrate ranges. Move the min
and max supported bitrates to the platform data.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Firmwares for encoders newer than MT8173 will include an ABI version
number in their initialization ack message. Add the capacity to manage
it and make initialization fail if the firmware ABI is of a version that
we don't support.
For MT8173, this ABI version field is reserved and thus undefined ; thus
ignore it on this chip. There should only be one firmware version available
for it anyway.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support the new extended firmware used by MT8183's encoder.
[acourbot: refactor, cleanup and split]
[hverkuil: fixed some checkpatch alignment warnings]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for communicating with the SCP firmware, which will be used
by MT8183.
[acourbot: refactor, cleanup and split]
[hverkuil: fixed some checkpatch alignment warnings]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MT8183's codec firmware is run by a different remote processor from
MT8173. While the firmware interface is basically the same, the way to
invoke it differs. Abstract all firmware calls under a layer that will
allow us to handle both firmware types transparently.
[acourbot: refactor, cleanup and split]
[pihsun: fix error path and add mtk_vcodec_fw_release]
[hverkuil: fixed some checkpatch alignment warnings]
[hverkuil: fixed merge conflicts]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Reviewed-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Please pull a set of fixes for various DRM drivers that finally resolve
incorrect usage of the scatterlists (struct sg_table nents and orig_nents
entries), what causes issues when IOMMU is used.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910080505.24456-1-m.szyprowski@samsung.com
In order to boot some of the new Venus firmware versions TZ call to set
virtual address ranges is needed. Add virtual address ranges for CP and
CP_NONPIX in resource structure and use them when loading and booting
the firmware on remote processor.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We have a new helper to set profile and level use it
instead.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the returned profile and level is not aligned with
v4l2 ctrl id. Correct that by use the helpers which translate
the v4l2 <-> hfi mapping internally.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Get and set VP9 codec profile and levels.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Introduce a helper to set and get profile and levels which
includes the translation between v4l2 ctrl ids and HFI ids.
The input arguments are always in v4l2 ids space.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the rcar-csi2 driver embeds it in the rcar_csi2
structure. This causes memory corruption when the notifier is destroyed
at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally.
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the rcar-drif driver embeds it in the
rcar_drif_graph_ep structure. This causes memory corruption when the
notifier is destroyed at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The fwnode reference corresponding to the endpoint is leaked in an error
path of the rcar_drif_parse_subdevs() function. Fix it, and reorganize
fwnode reference handling in the function to release references early,
simplifying error paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When devm_ioremap_resource() fails, isp should be
freed just like other error paths in isp_probe.
Fixes: 8644cdf972 ("[media] omap3isp: Replace many MMIO regions by two")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Documentation/DMA-API-HOWTO.txt states that the dma_map_sg() function
returns the number of the created entries in the DMA address space.
However the subsequent calls to the dma_sync_sg_for_{device,cpu}() and
dma_unmap_sg must be called with the original number of the entries
passed to the dma_map_sg().
struct sg_table is a common structure used for describing a non-contiguous
memory buffer, used commonly in the DRM and graphics subsystems. It
consists of a scatterlist with memory pages and DMA addresses (sgl entry),
as well as the number of scatterlist entries: CPU pages (orig_nents entry)
and DMA mapped pages (nents entry).
It turned out that it was a common mistake to misuse nents and orig_nents
entries, calling DMA-mapping functions with a wrong number of entries or
ignoring the number of mapped entries returned by the dma_map_sg()
function.
To avoid such issues, lets use a common dma-mapping wrappers operating
directly on the struct sg_table objects and use scatterlist page
iterators where possible. This, almost always, hides references to the
nents and orig_nents entries, making the code robust, easier to follow
and copy/paste safe.
dma_map_sgtable() function returns zero or an error code, so adjust the
return value check for the vsp1_du_map_sg() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into patchwork
Linux 5.9-rc4
* tag 'v5.9-rc4': (1001 commits)
Linux 5.9-rc4
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
...
-----BEGIN PGP SIGNATURE-----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=OwNa
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a compilation fix issue with ti-vpe on arm 32 bits
- two Kconfig fixes for imx214 and max9286 drivers
- a kernel information leak at v4l2-core on time32 compat ioctls
- some fixes at rc core unbind logic
- a fix at mceusb driver for it to not use GFP_ATOMIC
- fixes at cedrus and vicodec drivers at the control handling logic
- a fix at gpio-ir-tx to avoid disabling interruts on a spinlock
* tag 'media/v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mceusb: Avoid GFP_ATOMIC where it is not needed
media: gpio-ir-tx: spinlock is not needed to disable interrupts
media: rc: do not access device via sysfs after rc_unregister_device()
media: rc: uevent sysfs file races with rc_unregister_device()
media: max9286: Depend on OF_GPIO
media: i2c: imx214: select V4L2_FWNODE
media: cedrus: Add missing v4l2_ctrl_request_hdl_put()
media: vicodec: add missing v4l2_ctrl_request_hdl_put()
media: media/v4l2-core: Fix kernel-infoleak in video_put_user()
media: ti-vpe: cal: Fix compilation on 32-bit ARM
Sparse warns about this symbol:
drivers/media/platform/qcom/venus/hfi_venus.c:133:5: warning: symbol 'venus_fw_debug' was not declared. Should it be static?
Because hfi_venus.c doesn't include a header file with the
extern. So, move it to core.h, with is included by both
hfi_venus.c and dbgfs.c.
This way, if something changes with it, warnings or errors
will be produced.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here we introduce debug prefixes for dev_dbg groups by level of
importance - Venus{Low,Med,High,FW} Enabling the particular level
will be done by dynamic debug.
For example to enable debug messages with low level:
echo 'format "VenusLow" +p' > debugfs/dynamic_debug/control
If you want to enable all levels:
echo 'format "Venus" +p' > debugfs/dynamic_debug/control
All the features which dynamic debugging provide are preserved.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This will be useful when debugging specific issues related to
firmware HFI interface.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the standard menu control for frame skip mode in the MFC
driver. The legacy private menu control is kept for backward
compatibility.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds support for frame-skip-mode standard v4l2 control in
encoder driver. The control is implemented based on the
combination of client selected bitrate-mode and frame-skip-mode.
Once The client selected bitrate-mode (constant or variable) and
the frame-skip-mode is not disabled we set variable framerate for
rate controller.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds implementation of V4L2_CID_MPEG_VIDEO_CONSTANT_QUALITY v4l
control when the bitrate mode is CQ.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the recovery mechanism is using two hfi functions
to destroy and create interface queues. For the purpose of
recovery we don't need to free and allocate the memory used
for interface message queues, that's why we introduce new
function which just reinit the queues. Also this will give
to the recovery procedure one less reason to fail (if for
some reason we couldn't allocate memory).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After power domains and clock restructuring the recovery for
sdm845 and v4 did not work properly. Fix that by reworking the
recovery function and the sequence.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the hfi_parser has been called only once during driver
probe. To prepare the parser function to be called multiple times
from recovery we need to initialize few variables which are used
during parsing time.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On dragonboard-410c (apq8016) with HFI_VERSION_1XX, the reported
framerate is in unit of 1/65535 fps (for fine grained control).
So the current reported supported frame intervals is wrong (max
is 1/65535 fps), leading to encoding issues or format negotiation
failures with gstreamer.
Fix that by setting the framerate denominator to coherent value
based on the the framerate factor.
The factor is not always the same, e.g. with db820c (apq8096) HFI
reports framerate in fps unit. So only apply that for HFI_VERSION_1XX.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are few list handling issues while adding and deleting
node in the registered buf list in the driver.
1. list addition - buffer added into the list during buf_init
while not deleted during cleanup.
2. list deletion - In capture streamoff, the list was reinitialized.
As a result, if any node was present in the list, it would
lead to issue while cleaning up that node during buf_cleanup.
Corresponding call traces below:
[ 165.751014] Call trace:
[ 165.753541] __list_add_valid+0x58/0x88
[ 165.757532] venus_helper_vb2_buf_init+0x74/0xa8 [venus_core]
[ 165.763450] vdec_buf_init+0x34/0xb4 [venus_dec]
[ 165.768271] __buf_prepare+0x598/0x8a0 [videobuf2_common]
[ 165.773820] vb2_core_qbuf+0xb4/0x334 [videobuf2_common]
[ 165.779298] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 165.784053] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 165.789067] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 165.794624] v4l_qbuf+0x48/0x58
[ 1797.556001] Call trace:
[ 1797.558516] __list_del_entry_valid+0x88/0x9c
[ 1797.562989] vdec_buf_cleanup+0x54/0x228 [venus_dec]
[ 1797.568088] __buf_prepare+0x270/0x8a0 [videobuf2_common]
[ 1797.573625] vb2_core_qbuf+0xb4/0x338 [videobuf2_common]
[ 1797.579082] vb2_qbuf+0x78/0xb8 [videobuf2_v4l2]
[ 1797.583830] v4l2_m2m_qbuf+0x80/0xf8 [v4l2_mem2mem]
[ 1797.588843] v4l2_m2m_ioctl_qbuf+0x2c/0x38 [v4l2_mem2mem]
[ 1797.594389] v4l_qbuf+0x48/0x58
Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
vidioc_streamoff can be called multiple times from userspace, but we
should only call media_pipeline_stop when we're actually setup.
This became more noticeable after commit 2a2599c663 ("[media] media:
entity: Catch unbalanced media_pipeline_stop calls") was merged as it
added a WARN for unbalanced calls to media_pipeline_stop.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is no longer used since the conversion to DT
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a no-op as it is never set and is a remnant from non-DT days
that can be safely removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some devices, there may be multiple camera sensors attached
to the same port. Make sure we probe all of them, not just the
first one.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of keeping a local copy of how many sensors we've probed
(which may not even properly represent the number of sensors
probed if we have a port without a sensor), use the global
num_sensors counter that has the actual number used.
This will also make it easier to add support for multiple sensors
being connected to the same port.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ee7160e57c ("[media] s5p-fimc: Add support for JPEG capture")
added support for JPEG capture, but missed setting a register when the
parallel port was used rather than the CSIS device.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit bae4500399 ("[media] exynos4-is: Add missing entity function
initialization") tried to suppress the warnings such as
s5p-fimc-md camera: Entity type for entity FIMC.0 was not initialized!
However, this missed setting for the subdev. Set it now to avoid the
ugly warnings on boot.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Not all devices use the CSIS device, some may use the FIMC directly in
which case the CSIS device isn't registered. This leads to a nullptr
exception when starting the stream as the CSIS device is always
referenced. Instead, if getting the CSIS device fails, try getting the
FIMC directly to check if we are using the subdev API
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On FIMC variants which don't have writeback channel, there is no need to
access system registers. This patch makes the driver request sysreg
regmap conditionally depending on whether writeback is supported.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The S5PV210 platform only supports device tree based booting
where the FIMC variant data is parsed directly from
the device tree, hence the now unused static data can be removed.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no need to request the "idle" pinctrl state in the driver as that
is implemented in the driver core and the pinctrl_pm_* API can be used for
switching between the default and the idle state.
Simplify the pinctrl code to only request and check for the mandatory
"default" pinctrl state.
Switching between the default/idle pinctrl state is not yet implemented
in the driver and this patch doesn't change that.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The "idle" pinctrl state is optional as documented in the DT binding.
The change introduced by the commit being reverted makes that pinctrl state
mandatory and breaks initialization of the whole media driver, since the
"idle" state is not specified in any mainline dts.
This reverts commit 18ffec7505 ("media: exynos4-is: Add missed check for pinctrl_lookup_state()")
to fix the regression.
Fixes: 18ffec7505 ("media: exynos4-is: Add missed check for pinctrl_lookup_state()")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the definitions introduced by commit "media: camss: add support
for vidioc_enum_framesizes ioctl" instead of the hardcoded values.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VIDIOC_ENUM_FRAMESIZES support in the video capture driver is required by
libcamera. Without this change libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:1059 /dev/video0[cap]: Unable to enumerate
frame sizes: Inappropriate ioctl for device"
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement mbus_code filtering for format enumeration.
Without this patch libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:982 /dev/video0[cap]: Media bus code
filtering not supported by the device"
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media device is not usable by userspace before all devices involved
in capture are present in the system. Move registering of the media
device to the async complete callback.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the VIN device is part of a group of VIN devices (all Gen3 boards)
there is no reason to only unregister the group notifier if the VIN that
registers the notifier is removed. The VIN that registers the notifier
is always the last VIN device to be bound, so keeping the notifier
around after any VIN is unbound creates an unbalanced state where no VIN
in the group is operational.
Fix this by unconditionally unregistering the notifier when any VIN
device is unbound. Unregistering the notifier will lead to unbound()
being called and all video devices exposed by any VIN instance to be
removed.
The lock was only needed to protect the check which VIN registers the
notifier and is no longer needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On MMP3, the camera block lives on a separate power island. We want to
turn it off if the CCIC is not in use to conserve power.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This simplifies things a bit and makes adding runtime PM a bit more
straightforward.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sole reason for this was so that it would be possible to get a
mmp_camera from a platform_device in suspend/resume/remove hooks, because
drvdata used to be used by the v4l core.
Since commit 95db3a60e0 ("[media] v4l: Add a media_device pointer to the
v4l2_device structure") it is no longer case and thus we can make things
a great deal simpler.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 95db3a60e0 ("[media] v4l: Add a media_device pointer
to the v4l2_device structure") the v4l core doesn't insist on using drvdata
itself. Therefore we can use it ourselves, making things somewhat simpler.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The following W=1 build warning is seen on a m68k:
drivers/media/platform/fsl-viu.c: At top level:
drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined
36 | #define out_be32(v, a) iowrite32be(a, (void __iomem *)v)
|
In file included from ./arch/m68k/include/asm/io_mm.h:25,
from ./arch/m68k/include/asm/io.h:8,
from ./include/linux/io.h:13,
from ./include/linux/irq.h:20,
from ./include/asm-generic/hardirq.h:13,
from ./arch/m68k/include/generated/asm/hardirq.h:1,
from ./include/linux/hardirq.h:9,
from ./include/linux/interrupt.h:11,
from drivers/media/platform/fsl-viu.c:17:
./arch/m68k/include/asm/raw_io.h:32: note: this is the location of the previous definition
32 | #define out_be32(addr,l) (void)((*(__force volatile u32 *) (addr)) = (l))
Avoid the out_be32() and in_be32() redefinitions when building for CONFIG_M68K
in the same way we currently do for CONFIG_PPC and CONFIG_MICROBLAZE.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle report:
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:963:6-31:
WARNING: Comparison to bool
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle reports:
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:197:14-35:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:198:7-29:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:451:12-19:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:1159:6-15:
WARNING: Comparison to bool
By replacing (cond == true) with (cond) and (cond == false) with
(!cond)
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following coccinelle report:
drivers/media/platform/sunxi/sun8i-rotate/sun8i_rotate.c:751:2-9:
line 751 is redundant because platform_get_irq() already prints an error
By removing the useless call to dev_err()
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add mtk jpeg encode v4l2 driver based on jpeg decode, because that jpeg
decode and encode have great similarities with function operation.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add varability which would be used between jpeg dec and enc to a match
data structure, it will make the code linear.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename existing functions/defines/variables with a _dec prefix and
without dec_ prefix to prepare for the addition of the jpeg encoder
feature.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the files which are for decode feature. This is preparing
path since the jpeg enc patch will be added later.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the generic clk_bulk_* helpers to enable and disable clocks.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call mtk_jpeg_try_fmt_mplane() to replace the original computation of
sizeimage and bytesperline, because that mtk_jpeg_try_fmt_mplane()
already did it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jpeg doesn't support colorspace conversion, so it shouldn't accept any
other colorspace in S_FMT.
Change the colorspace of jpeg to the fixed value.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The standard v4l2_pix_format_mplane structure contains width/height/
sizeimage/bytesperline, so use v4l2_pix_format_mplane to replace them.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete the unused ctx parameter.
Using mtk_jpeg_formats and num_formats parameters is more generic,
because that jpeg enc will also use it.
Delete the macro definition of MTK_JPEG_FMT_TYPE_OUTPUT and
MTK_JPEG_FMT_TYPE_CAPTURE, because that MTK_JPEG_FMT_FLAG_DEC_OUTPUT
and MTK_JPEG_FMT_FLAG_DEC_CAPTURE are enough.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The function of mtk_jpeg_adjust_fmt_mplane() equals
mtk_jpeg_g_fmt_vid_mplane(), so use mtk_jpeg_g_fmt_vid_mplane() to
replace it .
Delete the unused ctx parameter.
Using fourcc to distinguish between different formats is more generic,
because that jpeg enc will also use it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum width and height supported by JPEG dec is 65535, so change
them from 8192 to 65535.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
JPEG dec does't support setting a compose rectangle, so remove
mtk_jpeg_dec_s_selection().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move MTK_JPEG_COMP_MAX definition to mtk_jpeg_core.h file, because it
is used by mtk_jpeg_core.c file.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use clamp() to replace mtk_jpeg_bound_align_image() and round() to
replace mtk_jpeg_align().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change register offset hex numerals from uppercase to lowercase.
Change data type of max/min width/height from integer to unsigned
integer.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete zeroing the reserved fields because that the core already
does it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no need to queue an empty buffer for signaling a last frame,
because all frames are separate from each other in JPEG.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a delayed work scheduled before starting the hardware and
canceled in the interrupt handler. If the delayed work is executed, it
resets the hardware and reports the failure to V4L2, so that the
execution can continue from next frames.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add v4l2_m2m_suspend() function call in mtk_jpeg_suspend() to make sure
that the current frame is processed completely before suspend.
Add v4l2_m2m_resume() function call in mtk_jpeg_resume() to unblock the
driver from scheduling next frame.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete the resetting hardware flow in suspend and resume function
because that resetting operation will be done in device_run().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call pm_runtime_get_sync() before starting a frame and then
pm_runtime_put() after completing it. This can save power for the time
between processing two frames.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver can be instantiated multiple times, e.g. for a decoder and
an encoder. Moreover, other drivers could coexist on the same system.
This makes the static video node number assignment pointless, so switch
to automatic assignment instead.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete platform_get_resource operation for irq.
Return actual value rather than EINVAL when fail to get and request
irq.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let v4l2_ctrl_subscribe_event() do the job for other types except
V4L2_EVENT_SOURCE_CHANGE.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Note that sun4i-csi didn't unregister the video device at all. That's
now fixed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Kconfig help text for VIDEO_MEDIATEK_VCODEC was referring to a
single module named mtk-vcodec, while this driver produces two modules
named mtk-vcodec-dec and mtk-vcodec-enc. Fix that.
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When compiled on 32-bit ARM, the CAL driver fails with the FIELD_PREP()
macro complaining that the mask is not constant. While all callers of
the inline cal_write_field() function pass a constant mask, the mask
parameter itself is a variable, which likely doesn't please the
compiler.
Fix it by replacing FIELD_PREP() with a manual implementation.
Fixes: 50797fb30b ("media: ti-vpe: cal: Turn reg_(read|write)_field() into inline functions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to add OPP tables and perf voting on the OPP powerdomain.
This is needed so venus votes on the corresponding performance state
for the OPP powerdomain along with setting the core clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Post a successful pm_ops->core_get, an error in probe
should exit by doing a pm_ops->core_put which seems
to be missing. So fix it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For other error
paths after this call, things are the same.
Fix this by adding pm_runtime_put_noidle() after 'err_runtime_disable'
label. But in this case, the error path after pm_runtime_put_sync()
will decrease PM usage counter twice. Thus add an extra
pm_runtime_get_noresume() in this path to balance PM counter.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the newly introduced get_mbus_config() subdevice pad operation to
retrieve the remote subdevice MIPI CSI-2 bus configuration and configure
the number of active data lanes accordingly.
In order to be able to call the remote subdevice operation cache the
index of the remote pad connected to the single CSI-2 input port.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the PXA camera driver to use the new set_mbus_config pad operation.
For this platform the change is not only cosmetic, as the pxa driver is
currently the only driver in mainline to make use of the g_mbus_config
and s_mbus_config video operations.
The existing driver semantic is the following:
- Collect all supported mbus config flags from the remote end
- Match them with the supported PXA mbus configuration flags
- If the remote subdevice allows multiple options for for VSYNC, HSYNC
and PCLK polarity, use platform data requested settings
The semantic of the new get_mbus_config and set_mbus_config differs from
the corresponding video ops, particularly in the fact get_mbus_config
reports the current mbus configuration and not the set of supported
configuration options, with set_mbus_config always reporting the actual
mbus configuration applied to the remote subdevice.
Adapt the driver to perform the following
- Set the remote subdevice mbus configuration according to the PXA
platform data preferences.
- If the applied configuration differs from the requested one (i.e. the
remote subdevice does not allow changing one setting) make sure that
- The remote end does not claim for DATA_ACTIVE_LOW, which seems not
supported by the platform
- The bus mastering roles match
While at there remove a few checks performed on the media bus
configuration at get_format() time as they do not belong there.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl8tEbwACgkQCF8+vY7k
4RUvgw//bIP9Jisg0wfUtjm34cRIKZ13PfMRYlaMKcz4Q2YVIcOCJN+xJ2kUo5M9
D78q91g0u90OjsYIDJe/P8oKxluwr0RgXkHKsgywA+OiTIvJIEFxuvn7uiNMHFCJ
BgU7inSZ39odgtrSbvqNAzOQgEqjx38I1NZathkRO1fr775Q5ZOhLn0fH1JroMsC
mgfVB76p9R/UjYlYZLHumQPyxkAfN02xXmuXAqiIGBVLi/57eyuhT4qYC8FAbse6
rYhiV3RHcZiiV0aec2HPP0BqRo5D3uIQW6Qv6FcSK8UDGpeBL8tX62Y47rqiPZED
RExDlAHnTZgUSgquXzc+OtOolfWPctFAg6uLVHm7VVnzDOkJLQUrKWj18hEqLu87
8H9BTo+DhDys1MUhJfzItTRsvcjke0SJUWsVhF8CWAI0PpnBH/inwLQhq2jcpsJb
x2VxjnXJ1iyLw6zD4tJpMWhQwbpHSVjQ2cGK7w0ppMqytWxK9KJCROCrJup0T3EY
lidp0gzymGZQxtpaUFksSAlsdjKUglrh3d1xCryZt5uepvMIFiPp+Vn6Ixmq+S8U
UKBhW15EhVbAQdJLw5O0vsxQ/4AVSIbGXUpV6BA9mnMw9ZbDL62qB6iumCykByZC
UyEvm/+MLLg1Y9JhyHmJzi6VI9gGZG9ayTpswhUlG4EGQDZ+U0w=
=SYqr
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Legacy soc_camera driver was removed from staging
- New I2C sensor related drivers: dw9768, ch7322, max9271, rdacm20
- TI vpe driver code was re-organized and had new features added
- Added Xilinx MIPI CSI-2 Rx Subsystem driver
- Added support for Infrared Toy and IR Droid devices
- Lots of random driver fixes, new features and cleanups
* tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (318 commits)
media: camss: fix memory leaks on error handling paths in probe
media: davinci: vpif_capture: fix potential double free
media: radio: remove redundant assignment to variable retval
media: allegro: fix potential null dereference on header
media: mtk-mdp: Fix a refcounting bug on error in init
media: allegro: fix an error pointer vs NULL check
media: meye: fix missing pm_mchip_mode field
media: cafe-driver: use generic power management
media: saa7164: use generic power management
media: v4l2-dev/ioctl: Fix document for VIDIOC_QUERYCAP
media: v4l2: Correct kernel-doc inconsistency
media: v4l2: Correct kernel-doc inconsistency
media: dvbdev.h: keep * together with the type
media: v4l2-subdev.h: keep * together with the type
media: videobuf2: Print videobuf2 buffer state by name
media: colorspaces-details.rst: fix V4L2_COLORSPACE_JPEG description
media: tw68: use generic power management
media: meye: use generic power management
media: cx88: use generic power management
media: cx25821: use generic power management
...
camss_probe() does not free camss on error handling paths. The patch
introduces an additional error label for this purpose. Besides, it
removes call of v4l2_async_notifier_cleanup() from
camss_of_parse_ports() since its caller, camss_probe(), cleans up all
its resources itself.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to call of_node_put(comp->dev_node); on the error paths in this
function.
Fixes: c8eb2d7e82 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state() and pci_enable/disable_device() to do required
operations. In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If platform_driver_register() fails within vpss_init() resources are not
cleaned up. The patch fixes this issue by introducing the corresponding
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implementation of media controller centric device configuration will add
code to the CAMERARX support section, which is already quite big. Move
it to a separate file to make the code more manageable. No functional
change is included.
The cal_camerarx_init_regmap() function is kept in cal.c and renamed to
cal_init_camerarx_regmap() as it's not specific to one CAMERARX
instance, but related to the whole CAL device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for the split of the camerarx code to a separate file, move
the CAL I/O accessors to cal.h. This requires renaming the accessors
with a cal_prefix, as the current names are too generic and prone to
namespace clashes.
The reg_read() and read_write() macros, that cover both CAL and CAMERARX
register access, are split in two groups of inline functions, one for
CAL access and one for CAMERARX access.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for implementation of media controller centric device
configuration, move all the video node handling support to a separate
file.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Specifying 'int' explicitly is generally preferred in the kernel for
unsigned int types. Fix the only wrong occurrence.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The phy->sensor NULL check in cal_camerarx_get_external_rate() is not
needed, as the V4L2 video devices are only registered when the sensor is
bound. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The external pixel rate is retrieved when starting the camerarx and only
used then. There's no need to store it in the cal_camerarx structure, it
can be returned by cal_camerarx_get_external_info() and explicitly
passed to cal_camerarx_config().
While at it, rename cal_camerarx_get_external_info() to
cal_camerarx_get_external_rate() to better reflect the function's
purpose.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor the camerarx start and stop procedure to group all the
corresponding operations in two functions, cal_camerarx_start() and
cal_camerarx_stop() instead of splitting them in multiple steps called
from the vb2 stream start and stop functions. This reduces the coupling
between the camerarx and the contexts, and better models the camerarx
hardware.
The cal_camerarx_start() is a reworked version of cal_camerarx_init()
with the description of the start procedure updated to match the AM65x,
DRA7[124567]x and DRA80xM TRMs. The cal_camerarx_wait_ready() function
is inlined in cal_camerarx_start() to better describe the start
procedure.
No functional change is included in the camerarx start and stop
procedures themselves, but the interleaving of the start steps with the
context configuration has been changed in cal_start_streaming().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for the camerarx refactoring, reorder functions without any
functional change to ease review of the refactoring itself.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx_max_lanes() function is a one-liner that has a single
caller. It doesn't improve readability. Inline it in its caller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To avoid making the cal_ctx structure layoug depend on the size of the
cal_formats array, allocate the active_fmt array dynamically. This
prepares for splitting the driver in multiple files.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for splitting the V4L2 API support to a separate file, call
cal_ctx_v4l2_init_formats() from cal_ctx_v4l2_register().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the media controller API by registering a media device and
initializing the media entities corresponding to the video devices. The
context initialization is slightly refactored as a result. The media
graph will be built in a subsequent change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_dev structure stores the platform_device pointer, but most
accesses to that field need the device pointer. Store the struct device
pointer directly to simplify the code, and use to_platform_device() in
the two locations that need the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print the hardware revision in the X.Y.R format, which is more readable
that the 32-bit hex value. For the hardware info register, only print
its value if it doesn't contain what we expect.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read the hardware revision and info right after allocating resources, as
there's no need to delay doing so until all initialization is complete.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create four functions to handle initialization, cleanup, registration
and unregistration of the V4L2 (and soon media controller) objects:
- init() is meant to be called early at probe time to initialize the
objects, before they get used from within the kernel
- cleanup() is the counterpart of init, and is meant to be called at the
end of the remove sequence to free all objects
- register() is meant to be called at the end of the probe sequence, to
register the userspace-facing devices
- unregister() is the counterpart of register, and is meant to be called
at the beginning for the remove sequence, to disallow access from
userspace
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CAL_NUM_CSI2_PORTS macro instead of the hardcoded numerical
value 2 to iterate over the CSI-2 ports.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isvcirqset() isn't used. The isportirqset() doesn't increase
readability. Inline the latter and simply drop the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CAL_NUM_CSI2_PORTS macro isn't a register definition. Move it to
cal.c, and fix indentation of the other macros while at it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver happens the use the same number of CAMERARX and context, but
coupling their cleanup at remove time is wrong. To prepare for the
introduction of additional contexts, decouple the two.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_quickdump_regs() dumps registers for the two CAMERARX instances.
Retrieve those instances from the cal_dev directly instead of going
through the contexts, and simplify the code by using a loop.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The async notifier is meant to bind to subdevs connected to the CSI-2
ports. Those ports are modelled by the CAMERARX phy instances. To
prepare for additional decoupling of contexts and phys, make the
notifier operate on phys. We still initialize and register the context
V4L2 support in the async notifier complete operation as that's our
signal that the userspace API is ready to be exposed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to create one async notifier per CAL context. Merge them
all in a single notifier, stored in cal_dev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The subdev notifier handling assumes a 1:1 mapping between CAL contexts
and notifiers. To prepare for merging the multiple notifiers into a
single one, retrieve the CAL context from the async subdev structure
instead of from the notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initialization of the context based on the connected sensor is split
between the async notifier .bound() and .complete() operations. Move it
all to a separate function and call it from .bound() operation to
prepare for the move of the notifiers from the contexts to the cal_dev.
Only V4L2 registration is kept in the .complete() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use ARRAY_SIZE(cal->ctx) to iterate over the cal->ctx array instead of
using the numerical value from the CAL_NUM_CONTEXT macro (or, worse,
hardcoding the value 2). This will allow reworking contexts with less
changes in the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DT port nodes corresponding to the CSI-2 inputs belong to the
CAMERARX instances. Move parsing of the DT properties to a new
cal_camerarx_parse_dt() function, called by cal_camerarx_create().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx_create() function allocates resources with devm_*, and
thus doesn't need any manual cleanup. Those won't hold true for long, as
we will need to store resources that have no devm_* allocation variant
in cal_camerarx. Furthermore, devm_kzalloc() is the wrong memory
allocation API for structures that can be accessed from userspace, as
device nodes can be kept open across device removal.
Add a cal_camerarx_destroy() function to destroy a CAMERARX instance
explicitly, and switch to kzalloc() for memory allocation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In cal_remove(), unregister the video devices as the first operation,
before cleaning up the V4L2 objects, to avoid use-after-free. This isn't
a complete solution yet, as video nodes can be kept open across
unregistration.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create cal_ctx_v4l2_unregister() and cal_ctx_v4l2_cleanup() functions to
unregister and cleanup the V4L2-related objects from the context, and
call them in cal_remove() and in the error path of cal_probe().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to delay most of the video device initialization until
the sensor subdevs are bound. Split the initialization and registration,
and perform the initialization when creating the context.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_device structure is meant to represent the whole device. In the
CAL case, this corresponds to the CAL, the CAMERARX instances and the
connected sensors. There should thus be a single v4l2_device instance.
Replace the per-context instance with a global instance in the cal_dev
structure.
Don't set the v4l2_device name manually as v4l2_device_register() sets
it to a value that is suitable for the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for decoupling the v4l2_device from the cal_ctx, don't set
the control handler in the v4l2_device and expect the video node to use
it automatically, but set the video node control handler directly. This
requires adding the sensor subdev controls to the control handler
manually, as that operation was performed on the v4l2_device by
v4l2_device_register_subdev().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Letting the v4l2_fwnode_endpoint_parse() function determine the bus type
automatically is deprecated. Set the bus type to DPHY manually as the TI
CAL only supports DPHY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the manual of_get_next_port() and of_get_next_endpoint()
implementations and the corresponding logic in the caller with a call to
of_graph_get_endpoint_by_regs(). This greatly simplifies OF parsing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Using the endpoint reg value to pass the CSI-2 source virtual channel ID
in DT is a hack, isn't documented in the DT bindings, and isn't used in
neither upstream DT nor TI official overlays. Hardcode the virtual
channel to 0 to simplify reworking the code, proper virtual channel
support will be implemented later.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_create_instance() function creates a CAL context. Rename it to
cal_ctx_create() to make its purpose more explicit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_probe() function is a bit long, add comments to delimitate
sections in order to improve readability. The platform_set_drvdata()
call is moved to a more logical place as a result.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_get_camerarx_regmap() function is called in a single place.
Inline it in its caller, as it results in a clear code flow.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the syscon_regmap_lookup_by_phandle_args() function to replace
manual lookup of the syscon regmap offset. This simplifies the
cal_camerarx_init_regmap() implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify the cal_probe() function by splitting the CAMERARX syscon
regmap retrieval to a separate function. A few local variables are
renamed in the process to shorten them (syscon_camerrx_*) or to make
them more accurate (parent isn't the parent OF node but the CAL device's
own OF node).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_dev field of the cal_dev structure is initialized but never
used. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace a manually unrolled loop with an explicit for loop to increase
readability when creating the CAMERARX and context instances. The
explicit NULL initialization of cal->phy[] and cal->ctx[] is removed, as
the cal structure is zeroed when allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the context-specific print macro to replace the last usage of the
v4l2_* print macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of retrieving the struct device for the platform device from the
v4l2_device, get it from the platform device directly. This prepares for
cleanups related to v4l2_device handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_capability bus_info field, filled by the VIDIOC_QUERYCAP ioctl
handler, specifies the location of the device in the system. For
platform devices, V4L2 specifies that the value must be "platform:"
followed by the device name. Fix the cal_querycap() function to set the
right value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The csi2_port field of the cal_ctx structure holds the context index,
and is independent from the CSI-2 port (even if it currently has the
same numerical value). Rename it to index to avoid the ambiguity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename all functions related to contexts with a cal_ctx_ prefix to
increase readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_data_get_num_csi2_phy() function simply returns
cal->data->num_csi2_phy, and is not consistently used across the driver,
as most accesses to cal->data->num_csi2_phy are open-coded. We could fix
those open-coded accesses to use cal_data_get_num_csi2_phy(), but that
wouldn't bring much in terms of readability, so inline
cal_data_get_num_csi2_phy() in its only caller instead, and drop the
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Group the CAMERARX functions together to make the overall driver
structure easier to navigate. This only moves functions around, no
functional change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename all functions related to CAMERARX with a cal_camerarx_ prefix,
and pass them a cal_camerarx pointer. This performs most of the
decoupling of the CAMERARX from the context.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor is connected to the CAMERARX. Store its pointer, as well as
the sensor pixel rate and the endpoint, in the cal_camerarx. This
prepares for decoupling the cal_camerarx and cal_ctx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Prepare for passing the cal_camerarx pointer instead of the cal_ctx
pointer to CAMERARX-related functions by adding print macros for
cal_camerarx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the dev_* print macros instead of the v4l2_* print macros. This
prepares for a common print infrastructure that will also support the
cal_camerarx instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Store a pointer to the cal_dev and the cal_camerarx instance number in
the cal_camerarx structure. This prepares for passing a cal_camerarx
pointer instead of a cal_ctx pointer to multiple functions that deal
with the CAMERARX.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx structure describes the PHY, there's no need for an
internal structure named phy. Removed that level of indirection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Name all variables that point to a cal_camerax instance 'phy' instead of
'cc'. The name 'cc' refers to Camera Core, but is not commonly used in
the driver or in datasheets.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Name all variables pointing to a cal_dev instance 'cal', instead of a
combination of 'caldev' and 'dev'. 'caldev' is only used in a few places
and could have been renamed to 'dev', but 'dev' is confusing as it's
also used for struct device instances. This generates lots of changes,
but increases readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_csi2_phy contains platform data for the CAMERARX blocks. Rename
it to cal_camerarx_data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The various data structures that describe the components of the camera
access layer (CAL) are named without much consistency. Start cleaning
this up by renaming the structure that describes the CAMERARX block,
cc_data, to cal_camerarx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the csi2_phy_config() function to avoid its forward declaration. No
functional change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_dev flags field is a copy of data->flags. Use the latter and
remove the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove structure fields that are never set, set and never read, or set
to a fixed value. This allows removal of a global variable and a macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The global static const cal_regmap_config template is only used in a
single location, to initialize 3 fields of a local variable. Two of
those fields then get overwritten. Remove the template and set the last
remaining field manually. Simplify the code by hardcoding the field
values instead of calculating them for a variable that always has the
same value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that no platform data fields are modified at runtime, make the
corresponding structures const. The const qualifier for integer fields
is removed as it's not required anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Several structure fields declared as int store positive values only.
Make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_csi2_phy structure has lost its 'fields' field that used to
clash with the 'base_fields' field. Rename base_fields to fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PHY regmap fields are created dynamically at runtime. They don't
belong to the platform data that should be constant. Move them to the
cc_data structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to constify cal_csi2_phy, avoid modifying the base_fields
array at runtime. As the array now only needs to stored two values
instead of a full struct reg_field instance, save memory by using a
custom structure for the base_fields elements.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The base_fields field of cal_csi2_phy points to a fixed-size array of
struct reg_field. This level of indirection isn't needed, embed the
array directly in struct cal_csi2_phy.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Many loop indices only take positive values. Make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The found_port variable contains a boolean value, make it a bool.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A few local variables are needlessly initialized. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The static cal_formats array contains const data, make it const. This
requires turning a few cal_fmt pointers into const pointers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Turn the reg_(read|write)_field() macros into inline functions for
additional type safety. Use the FIELD_GET() and FIELD_PREP() macros
internally instead of reinventing the wheel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CAL_VERSION macro is used once only, in MODULE_VERSION(). This
doesn't improve readability, inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_irq() function reads three IRQ status registers and stores their
values in three different variables. As each value is processed right
after reading the corresponding register, a single variable is enough.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet numbers the IRQ registers starting from 0. Update the
numbering scheme to match the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet numbers the CSI-2 PHYs (external to the CAL) starting from
1, but the PPI inputs to the CAL starting from 0. Update the numbering
scheme for csi2_port to match the datasheet, which also simplifies the
driver by removing the need to constantly subtract 1 from the value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CPORT mentioned in the CAL documentation has nothing to do with the
CSI-2 ports. It's a remnant of CSI-3 support (or an attempt to achieve
it), and now only serves as an arbitraty tag value used to associate
data samples with contexts. Add a cport field to the cal_ctx structure
and use it instead of the CSI-2 port number where a CPORT is required by
the hardware. The value of the cport field is currently the same as the
csi2_port field, so there's no functional change, but this will help
reworking CPORT and CSI-2 port handling separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the cal_complete_ctx() function earlier in the file to avoid a
foward declaration. There is no functional change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Memory allocated with 'v4l2_m2m_init()' must be freed by a corresponding
call to 'v4l2_m2m_release()'
Also reorder the code at the end of the probe function so that
'video_register_device()' is called last.
Update the error handling path accordingly.
Fixes: 5ce60d790a ("[media] s5p-g2d: Add DT based discovery support")
Fixes: 918847341a ("[media] v4l: add G2D driver for s5p device family")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: checkpatch: align with parenthesis]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's all too easy to get confused by the V4L2_TYPE_IS_OUTPUT
macro, when it's used as !V4L2_TYPE_IS_OUTPUT.
Reduce the risk of confusion with macro to explicitly
check for the CAPTURE queue type case.
This change does not affect functionality, and it's
only intended to make the code more readable.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: checkpatch: align with parenthesis]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The component offsets were computed in a negative way: they were
subtracted from the actual color component value.
So, a higher offset was reducing the component value.
This is not really desirable, as the offset is a 2's complements
number with 1 bit for sign and 12 value bits, so we would like to be able
to also add to the component, not only subtract.
The reported number in v4l2 is fine, a range from -4095 to +4095.
However when configuring a negative value for the offset, this would in
fact not function, because with the old code, the number was subtracted
from the max value. By setting something negative, it was overflowing in
fact. Reworked the component offsets by placing the real value as the
v4l2 ctrls.
Now, the values are the real number that is added or subtracted from
the component.
The negative values received from v4l2 are already in 2's complements, so
there is no need for conversion.
This actually simplifies a lot the computation procedure, eliminating the
need for the macros that convert from v4l2 values to ISC values and
viceversa.
Also the ZERO_VAL is eliminated, as 0 is now 0, as it's supposed to be.
Example after this change:
# v4l2-ctl --set-ctrl=red_component_offset=-150 -L
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=16 value=20 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0 flags=update
do_white_balance 0x0098090d (button) : flags=inactive, write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=3 step=1 default=3 value=3 flags=slider
red_component_gain 0x009819c0 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
green_red_component_gain 0x009819c2 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
green_blue_component_gain 0x009819c3 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
red_component_offset 0x009819c4 (int) : min=-4095 max=4095 step=1 default=0 value=-150 flags=slider
blue_component_offset 0x009819c5 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
green_red_component_offset 0x009819c6 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
green_blue_component_offset 0x009819c7 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
The auto white balance algorithm is unchanged, but the obtained value to
'subtract' is now converted to negative and saved as a v4l2 control and
displayed properly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TI DAVINCI SERIES MEDIA DRIVER: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver didn't call _vb2_fop_release in the sun4i_csi_release
function. Without that call the vb2 queue is not properly canceled and
buffers may not be freed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For no obvious reason VB2_DMABUF was not enabled. Add this.
Also both read and write file ops were set, but this was not enabled
in the vb2 io_modes or in the device_caps capabilities. Drop this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes a v4l2-compliance warning:
Required ioctls:
warn: v4l2-test-media.cpp(52): empty bus_info
test MEDIA_IOC_DEVICE_INFO: OK
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting the output CSC mode is required for a YUV output, but must not
be set when the input is also YUV. Doing this (as tested with a YUV420P
to YUV420P conversion) results in wrong colors.
Adapt the logic to only set the output CSC mode when the output is YUV and
the input is RGB. Also add a comment to clarify the rationale.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This introduces two macros: RGA_COLOR_FMT_IS_YUV and RGA_COLOR_FMT_IS_RGB
which allow quick checking of the colorspace familily of a RGA color format.
These macros are then used to refactor the logic for CSC mode selection.
The two nested tests for input colorspace are simplified into a single one,
with a logical and, making the whole more readable.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
fimc_md_get_pinctrl() misses a check for pinctrl_lookup_state().
Add the missed check to fix it.
Fixes: 4163851f7b ("[media] s5p-fimc: Use pinctrl API for camera ports configuration]")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not possible for "pcdev->mclk" to be zero because we check for
that earlier and set it to 20000000 in that situation. If it were
possible, that would be a problem because it could have lead to an Oops
in the error handling when we call v4l2_clk_unregister(pcdev->mclk_clk);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the driver was picked-up the starting of the PHY have changed
quiet a bit. An artifact of these changes is the now poorly named
callback confirm_start(). It used to confirm start of the PHY but now
performs post PHY start initialization, rename it to phy_post_init() to
reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Several drivers implement the same enclosed_rectangle() function to
check if a rectangle is enclosed into another. Replace this with the
newly added v4l2_rect_enclosed() helper function.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds support for MEDIA_BUS_FMT_SRGGB8_1X8 format for CSI2
input.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for MEDIA_BUS_FMT_SRGGB8_1X8 format in rcar-vin by setting
format type to RAW8 in VNMC register and appropriately setting the bpp
and bytesperline to enable V4L2_PIX_FMT_SRGGB8.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Up until now the VIN was capable to convert any of its supported input mbus
formats to any of it's supported output pixel formats. With the addition of
RAW formats this is no longer true.
This patch invalidates the pipeline by adding a check if given vin input
format can be converted to supported output pixel format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we are considering the instances which are available
in core->inst list for load calculation in min_loaded_core()
function, but this is incorrect because by the time we call
decide_core() for second instance, the third instance not
filled yet codec_freq_data pointer.
Solve this by considering the instances whose session has started.
Cc: stable@vger.kernel.org # v5.7+
Fixes: 4ebf969375 ("media: venus: introduce core selection")
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the confusing SoC Camera reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since components are registered in a list, the numeric component id that
specified a location in an array is not necessary.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions mtk_mdp_register/unregister_component have been created to
add / remove items from the list of components.
This will eventually enable us to specify a list of components in the
device tree instead of hardcoding them into this driver.
The list is modified by a single thread at driver probe time, and will
not be traversed by another thread until the call to pm_runtime_enable
at the end of probing.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is a cleanup to better handle errors during MDP probe.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These fields are not used and can be removed.
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mtk-mdp driver uses states to check if the formats have been set
on the capture and output when turning the streaming on, setting
controls or setting the selection rectangles.
Those states are reset when 0 buffers are requested like when checking
capabilities.
This patch removes all format checks and set one by default as queues in
V4L2 are expected to always have a format set.
https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-streamon.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-ctrl.htmlhttps://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/vidioc-g-selection.html
Signed-off-by: Francois Buergisser <fbuergisser@chromium.org>
Signed-off-by: Eizan Miyamoto <eizan@chromium.org>
Reviewed-by: Enric Balletbo I Serra <enric.balletbo@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes coccicheck warning:
./drivers/media/platform/coda/coda-jpeg.c:331:3-31:
alloc with no test, possible model on line 354
Add NULL check after kmalloc.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently for msm_csiphy, msm_csid, and msm_ispif subdevices the media
entity function field is set to MEDIA_ENT_F_IO_V4L. This is incorrect
as MEDIA_ENT_F_IO_V4L implies V4L2 video node.
Change it to MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER as this is the best
fit from the functions defined in include/uapi/linux/media.h.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the use of dev->archdata.iommu and use the private per-device
pointer provided by IOMMU core code instead.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200625130836.1916-2-joro@8bytes.org
After mm.h was removed from the asm-generic version of cacheflush.h,
s390 allyesconfig shows several warnings of the following nature:
In file included from arch/s390/include/generated/asm/cacheflush.h:1,
from drivers/media/platform/omap3isp/isp.c:42:
include/asm-generic/cacheflush.h:16:42: warning: 'struct mm_struct' declared inside parameter list will not be visible outside of this definition or declaration
As Geert and Laurent point out, this driver does not need this header in
the two files that include it. Remove it so there are no warnings.
Link: http://lkml.kernel.org/r/20200622234740.72825-2-natechancellor@gmail.com
Fixes: e0cf615d72 ("asm-generic: don't include <linux/mm.h> in cacheflush.h")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
preview_init_entities() does not call v4l2_ctrl_handler_free() when
it fails.
Add the missed function to fix it.
Fixes: de1135d44f ("[media] omap3isp: CCDC, preview engine and resizer")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mccic_register() forgets to cleanup the notifier in its error handler.
mccic_shutdown() also misses calling v4l2_async_notifier_cleanup().
Add the missed calls to fix them.
Fixes: 3eefe36cc0 ("media: marvell-ccic: use async notifier to get the sensor")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When platform_get_resource() returns an error code, a
pairing runtime PM usage counter decrement is needed
to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For all error
paths after pm_runtime_get_sync(), things are the same.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Xilinx MIPI CSI-2 Rx Subsystem soft IP is used to capture images
from MIPI CSI-2 camera sensors and output AXI4-Stream video data ready
for image processing. Please refer to PG232 for details.
The CSI2 Rx controller filters out all packets except for the packets
with data type fixed in hardware. RAW8 packets are always allowed to
pass through.
It is also used to setup and handle interrupts and enable the core. It
logs all the events in respective counters between streaming on and off.
The driver supports only the video format bridge enabled configuration.
Some data types like YUV 422 10bpc, RAW16, RAW20 are supported when the
CSI v2.0 feature is enabled in design. When the VCX feature is enabled,
the maximum number of virtual channels becomes 16 from 4.
Signed-off-by: Vishal Sagar <vishal.sagar@xilinx.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=HeJz
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull more media updates from Mauro Carvalho Chehab:
- a set of atomisp patches. They remove several abstraction layers, and
fixes clang and gcc warnings (that were hidden via some macros that
were disabling 4 or 5 types of warnings there). There are also some
important fixes and sensor auto-detection on newer BIOSes via ACPI
_DCM tables.
- some fixes
* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
media: rkvdec: Fix H264 scaling list order
media: v4l2-ctrls: Unset correct HEVC loop filter flag
media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
media: v4l2-subdev.rst: correct information about v4l2 events
media: s5p-mfc: Properly handle dma_parms for the allocated devices
media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
media: cedrus: Implement runtime PM
media: cedrus: Program output format during each run
media: atomisp: improve ACPI/DMI detection logs
media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
media: Revert "media: atomisp: Add some ACPI detection info"
media: atomisp: improve sensor detection code to use _DSM table
media: atomisp: get rid of an iomem abstraction layer
media: atomisp: get rid of a string_support.h abstraction layer
media: atomisp: use strscpy() instead of less secure variants
media: atomisp: set DFS to MAX if sensor doesn't report fps
media: atomisp: use different dfs failed messages
media: atomisp: change the detection of ISP2401 at runtime
media: atomisp: use macros from intel-family.h
media: atomisp: don't set hpll_freq twice with different values
...
Commit 9495b7e92f ("driver core: platform: Initialize dma_parms for
platform devices") in v5.7-rc5 added allocation of dma_parms structure to
all platform devices. Then vb2_dma_contig_set_max_seg_size() have been
changed not to allocate dma_parms structure and rely on the one allocated
by the device core. Lets allocate the needed structure also for the
devices created for the 2 MFC device memory ports.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 9495b7e92f ("driver core: platform: Initialize dma_parms for platform devices")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to lead to some crazy include loops when using
asm-generic/cacheflush.h on more architectures, so leave it to the arch
header for now.
[hch@lst.de: fix warning]
Link: http://lkml.kernel.org/r/20200520173520.GA11199@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Will Deacon <will@kernel.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200515143646.3857579-7-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement a notifier bound op to register media links from the remote
sub-device's source pad(s) to the video-mux sink pad(s).
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use v4l2_subdev_get_fwnode_pad_1_to_1() as the get_fwnode_pad operation.
The video mux maps fwnode port numbers and pad indexes 1:1.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of using the convenience function
v4l2_async_register_fwnode_subdev(), parse the video-mux input endpoints
and set up the async sub-devices without using callbacks. The video-mux
knows which ports it must parse (the input ports) and how to handle
unconnected remotes, so it makes the code simpler to transfer control
of endpoint parsing to the driver.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since its inclusion in v3.9, no users of the SuperH VEU mem2mem video
processing driver have appeared upstream. All VEU devices in SuperH
board code still bind to the "uio_pdrv_genirq" driver instead.
The original author marked the driver orphaned in v3.15.
Remove the driver; it can always be resurrected from git history when
needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Landley <rob@landley.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set the V4L2_CAP_IO_MC capability flag and remove the driver specific
vidioc_enum_input, vidioc_g_input and vidioc_s_input callbacks for the
media controller enabled part of the driver. Also add support mbus_code
filtering for format enumeration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It is spurious to call 'clk_disable_unprepare()' when
'clk_prepare_enable()' has not been called yet.
Re-order the error handling path to avoid it.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: err_exlusive_rate -> err_exclusive_rate]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
gcc warns about empty array declarations, which we get in this driver
when compile-testing without CONFIG_OF:
drivers/media/platform/ti-vpe/cal.c:2194:34: warning: array 'cal_of_match' assumed to have one element
2194 | static const struct of_device_id cal_of_match[];
Since all users of this driver do need CONFIG_OF anyway, there is no
point in making the array definition conditional to save space, so
just remove the #ifdef and move the array up a little.
Fixes: 343e89a792 ("[media] media: ti-vpe: Add CAL v4l2 camera capture driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to latest H/W manual v1.50, the description of channel
number in the VCDT/VCDT2 register is decremented by one.
Therefore, this patch fixes it about comment.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to the v4l spec s_fmt must return EBUSY while the
particular queue is streaming. Add such check in encoder and
decoder s_fmt methods.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to stateful Codec API the decoder will process all
remaining buffers from before the source change event in
dynamic-resolution-change state and mark the last buffer with
V4L2_BUF_FLAG_LAST.
In Venus case the firmware doesn't mark that last buffer and
some mechanism have to be created in v4l decoder driver.
Fortunately the firmware interface (HFI) claims that the
decoder output buffers will be returned to v4l decoder
driver before it send the insufficient event.
In order to do that we save last queued in the driver capture
buffer in the event_notify and issue flush on output firmware
buffers queue. Once the saved buffer is returned (as a result of
flush command) we mark it as LAST. For all that possible we
extend HFI flush command with one more argument and one more
flush_done HFI driver callback.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the list initialization is done only in
dynamic-resolution-change state, which leads to list corruptions
and use-after-free. Init list_head unconditionally in
vdec_stop_capture called by vb2 stop_streaming without takeing
into account current codec state.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Once the hfi_session_flush is issued by the vdec all queued
buffers to firmware should be returned to the v4l driver. Some
of those buffers are not processed at the time of flush command,
those buffers has filled len zero (no data). Catch that in
buffer_done callback and mark not filled capture buffers with
error state so that client can discard them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently calling venus_helper_buffers_done() will return buffers to
user for both capture and output queues in the same call. This is
wrong because both queues are really separate and calling
stop_streaming on one queue shouldn't return buffers for the other.
Solve this by add a new queue type argument and fix the clients of
the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The array is not changed in the code, so make it const.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hfi_destroy function is called too early in remove method. It
destroys a mutex which is used later in the .remove from pmruntime.
Solve the issue by moving hfi_destroy after last usage of the mutex.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the encoder enables the rate control algorithms if the bitrate
control is non-zero. Implement the V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE
and V4L2_CID_MPEG_VIDEO_MB_RC_ENABLE controls to allow userspace to
choose frame-level or macroblock-level rate control updates, or to
explicitly disable rate control. Both controls are initially enabled to
keep the current behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enabling CONFIG_DMA_API_DEBUG=y and CONFIG_DMA_API_DEBUG_SG=y will
enable extra validation on DMA operations ensuring that the size
restraints are met.
When using the FCP in conjunction with the VSP1/DU, and display frames,
the size of the DMA operations is larger than the default maximum
segment size reported by the DMA core (64K). With the DMA debug enabled,
this produces a warning such as the following:
"DMA-API: rcar-fcp fea27000.fcp: mapping sg segment longer than device
claims to support [len=3145728] [max=65536]"
We have no specific limitation on the segment size which isn't already
handled by the VSP1/DU which actually handles the DMA allcoations and
buffer management, so define a maximum segment size of up to 4GB (a 32
bit mask).
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 7b49235e83 ("[media] v4l: Add Renesas R-Car FCP driver")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
aliases property name must include only lowercase and '-'. Fix in dts
and driver.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer 'common' is being assigned with a value that is never read,
the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As CEC support doesn't depend on MEDIA_SUPPORT, let's
place the platform drivers outside the media menu.
As a side effect, instead of depends on PCI, seco driver
can select it (and DMI).
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The stop-state timeout needs to be over 100us as per CSI spec. With the
CAL fclk of 266 MHZ on DRA76, with the current value the driver uses,
the timeout is 24us. Too small timeout will cause failure to enable the
streaming.
Also, the fclk can be different on other SoCs, as is the case with AM65x
where the fclk is 250 MHz.
This patch fixes the timeout by calculating it correctly based on the
fclk rate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sometimes there is a timeout when waiting for the Stop-State. Testing
shows that sometimes we need to wait more than what the current code
does. It is not clear how long this wait can be, but it is based on how
quickly the sensor provides a valid clock, and how quickly CAL syncs to
it.
Change the code to make it more obvious how long we'll wait, and set a
wider range for usleep_range. Increase the timeout to 750ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sometimes there is a timeout when waiting for the 'ComplexIO Reset
Done'. Testing shows that sometimes we need to wait more than what the
current code does. It is not clear how long this wait can be, but it is
based on how quickly the sensor provides a valid clock, and how quickly
CAL syncs to it.
Change the code to make it more obvious how long we'll wait, and set a
wider range for usleep_range. Increase the timeout to 750ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To make csi2_wait_for_phy() more readable, move code to separate
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: delete empty line before } ]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set DMA max seg size correctly to get rid of warnings on 64 bit
platforms:
DMA-API: cal 6f03000.cal: mapping sg segment longer than device claims to support [len=720896] [max=65536]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL_CSI2_CTX register has LINES field, which, according to the
documentation, should be programmed to the number of lines transmitted
by the camera. If the number of lines is unknown, it can be set to 0.
The driver sets the field to 0 for some reason, even if we know the
number of lines.
This patch sets the number of lines properly, which will allow the HW to
discard extra lines (if the sensor would send such for some reason),
and, according to documentation: "This leads to regular video timings
and avoids potential artifacts".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After ComplexIO reset, a dummy read to PHY is needed as per CAL spec to
finish the reset. Currently the driver reads a ComplexIO register, not
PHY register. Fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the code to enable and disable ComplexIO power to its own function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify the code by using reg_write_field() where trivially possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove a bunch of IRQ defines, of which only CAL_HL_IRQ_ENABLE and
CAL_HL_IRQ_CLEAR are used, and these defines only end up obfuscating
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These macros only obfuscate the code, so drop them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of having identical code block to handle irqs for the two CAL
ports, we can have a for loop and a single code block.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver does not print any errors on ComplexIO reset timeout or when
waiting for stop-state, making it difficult to debug and notice
problems.
Add error prints for these cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAL reports various errors via IRQs, which are not handled at all by the
current driver. Add code to enable and catch those IRQs and print
errors. This will make it much easier to notice and debug issues with
sensors.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix: spaces preferred around that '-']
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that cal_runtime_get and cal_runtime_put are only direct wrappers to
pm_runtime_get/put, we can drop cal_runtime_get and cal_runtime_put.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to do errata handling every time CAL is being enabled. The code
is currently in cal_runtime_get(), which is not the correct place for
it.
Move the code to cal_runtime_resume, which is called every time CAL is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
i913_errata() sets a bit to 1 in PHY_REG10, but for some reason uses
CAL_CSI2_PHY_REG0_HSCLOCKCONFIG_DISABLE for the bit value. The value of
that macro is 1, so it works, but is still wrong.
Fix this to 1.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IRQENABLE_SET registers are (usually) not meant to be read, only written
to. The current driver needlessly uses read-modify-write cycle to enable
IRQ bits.
The read-modify-write has no bad side effects here, but it's still
better to clean this up by only using write.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the CAL driver stops streaming, it will shut everything down
without waiting for the current frame to finish. This leaves the CAL DMA
in a slightly undefined state, and when CAL DMA is enabled when the
stream is started the next time, the old DMA transfer will continue.
It is not clear if the old DMA transfer continues with the exact
settings of the original transfer, or is it a mix of old and new
settings, but in any case the end result is memory corruption as the
destination memory address is no longer valid.
I could not find any way to ensure that any old DMA transfer would be
discarded, except perhaps full CAL reset. But we cannot do a full reset
when one port is getting enabled, as that would reset both ports.
This patch tries to make sure that the DMA transfer is finished properly
when the stream is being stopped. I say "tries", as, as mentioned above,
I don't see a way to force the DMA transfer to finish. I believe this
fixes the corruptions for normal cases, but if for some reason the DMA
of the final frame would stall a lot, resulting in timeout in the code
waiting for the DMA to finish, we'll again end up with unfinished DMA
transfer. However, I don't know what could cause such a timeout.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Venus driver is voting Configuration NoC during .probe but not clear
voting in .suspend. Because of this NoC is up during shutdown also. As a
consequence the whole device could leak energy while in .suspend.
So correct this by moving voting in .resume and unvoting
in .suspend
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement pmruntime autosuspend in video decoder. This will
allow to save power while the userspace is inactive for some
reasonable period of time. Here we power-off venus core clocks
and power domain and don't touch vcodec because it is under
hardware control. The later decision is made to simplify the
code and avoid a mess in the power management code.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each jpeg can have the huffman tables optimized for its specific content
meaning that the table lenghts and values don't match the standard table
of substitutions so there's no reason to hardcode and expect the standard
lengths, otherwise we just end up rejecting optimized jpegs altogether.
Tested on CODA960.
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Similar to commit 9ee50a9489 ("media: coda: lock capture queue wakeup
against encoder stop command"), make sure that a JPEG decoder stop
command running concurrently with a decoder finish_run always either
flags the last returned buffer or wakes up the capture queue to signal
the end of stream condition afterwards.
This was not necessary for BIT processor contexts because of the need to
release the bitstream buffer with the stream end condition. In contrast,
the JPEG decoder can be finished with decoding the image between the
time the application queues the last output buffer and the time it
issues the decoder stop command.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If a JPEG decoding application queues the last capture and output
buffers, issues a decoder stop command after the decoding is already
done, and then dequeues the last capture buffer, it is not marked as
last. Detect this condition in the decoder stop command and mark the
last buffer on the capture done list.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split marking the last metadata entry into a helper function to simplify
coda_decoder_cmd.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG decoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG decoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can decode
4:2:2 subsampled JPEG images into YUV422P.
[m.felsch@pengutronix.de: fix qsequence counting by explicitly
checking for the !use_bit case]
[hverkuil-cisco@xs4all.nl: fix 'warning: missing braces around initializer']
[mchehab+huawei@kernel.org: fix 'BRACES: Unbalanced braces around else statement']
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The BIT decoders always write 16x16 macroblocks. Align stride and height to
avoid spilling luma data into the top of the chroma planes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Changing from "depends on" to "select" may cause some
side-effects. This patch is not ready to be merged yet,
as it requires some adjustments.
So, let's revert it.
This reverts commit a3b91d8bd1.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those documents don't really describe the driver API.
Instead, they contain development-specific information.
Yet, as the main index file describes the content of it as:
"how specific kernel subsystems work
from the point of view of a kernel developer"
It seems to be the better fit.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are lots of drivers that only work when the media controller
and/or the V4L2 subdev APIs are present.
Right now, someone need to first enable those APIs before
using those drivers.
Well, ideally, drivers, should, instead *optionally*
depend on it, in order for PC camera drivers to be able to use
them, but nowadays most drivers are UVC cameras, with don't
require a sensor driver.
So, be it.
Let's instead make them select the MEDIA_CONTROLLER and the
SUBDEV API, in order to make easier for people to be able
of enabling them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most of media Kconfig/Makefile files already has SPDX,
but there are a few ones still missing. Add it to them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now, if one has an hybrid TV card, it has to select
both analog and digital TV support, as otherwise the needed
core support won't be selected.
Change the logic to auto-select the core support for those
drivers, as this is a way more intuitive.
It should be noticed that, as now both DVB_CORE and VIDEO_DEV
defaults depends on selecting a hybrid cards, we had to remove
the explicit dependencies there, in order to avoid circular
dependencies.
That requires some tricks:
1) the prompt should not be not visible when an hybrid card
is selected, as the user shold not change it.
2) When a media hybrid device is selected, the modular
option for DVB_CORE and VIDEO_DEV will follow the
MEDIA_SUPPORT dependency, as we can't have a core
built with "y" with a driver built as module.
Note: while here, moved two pure V4L2 PCI drivers out of the
"hybrid" part of config and consider pvrusb2 as an hybrid
device.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the first test device was added (vivi.c), there were just
one file. I was too lazy on that time to create a separate
directory just for it, so I kept it together with platform.
Now, we have vivid, vicodec, vim2m and vimc. Also, a new
virtual driver has been prepared to support DVB API.
So, it is time to solve this mess, by placing test stuff
on a separate directory.
It should be noticed that we also have some skeleton drivers
(for V4L and for DVB). For now, we'll keep them separate,
as they're not really test drivers, but instead, just
examples. The DVB frontend ones will likely be part of a new DVB
test driver. By that time, it should make sense to move them
here as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When the platform drivers got added, they were all part of
complex camera support. This is not the case anymore, as we
now have codecs and other stuff there too.
So, fix the dependencies, in order to not require users to
manually select something that it doesn't make sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
With the latest cleanup in qcom scm driver the secure monitor
call for setting the remote processor state returns EINVAL when
it is called for the first time and after another scm call
auth_and_reset. The error returned from scm call could be ignored
because the state transition is already done in auth_and_reset.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mt8173 VPU firmware has been moved to a sub-folder of
linux-firmware, so load vpu-fw from the new location first,
if it fails, then from the old one.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initial physical address was one too low for the outputs.
E.g. if 1.0.0.0 was expected, then it was set to 0.0.0.0, and
2.0.0.0 became 1.0.0.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Johan Korsnes <johan.korsnes@gmail.com>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch makes use of to_vpfe() to get a pointer to vpfe_device
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of of_clk_get and print an error
message if not EPROBE_DEFER.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to not print an error message when the
device probe operation is deferred.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to defer probe when auxiliary clock
"hdmi-cec" is registered in the system not has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf15 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.
Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following smatch warning in the error path:
drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
warn: inconsistent returns 'mutex:&inst->lock'.
Locked on: line 952
Unlocked on: line 963
line 968
by goto mutex unlock.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the previously introduced v4l2-mem2mem core APIs to handle the drainig,
stopped and next-buf-is-last states.
With these changes, the v4l2-compliance still passes with the following
commands :
>>>><><><><><><><><><><><><><><><><>< 15.53 fps
15.53 fps
><><><><><><><><><><><><>< 13.99 fps
13.99 fps
><><><><><><><><><><><>< 13.52 fps
13.52 fps
><><><><><><><><><><><><>< 13.41 fps
13.41 fps
><><><><><><><><><><><><>< 13.21 fps
13.21 fps
><><><><><><><><><><><>< 13.09 fps
13.09 fps
><><><><><><><
STOP ENCODER
<<<
EOS EVENT
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video0: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [1]
v4l2-compliance SHA: 7ead0e1856b89f2e19369af452bb03fd0cd16793, 64 bits
[...]
Total for vicodec device /dev/video1: 50, Succeeded: 50, Failed: 0, Warnings: 0
The full output is available at [2]
No functional changes should be noticed.
[1] https://termbin.com/25nn
[2] https://termbin.com/dza4
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Suggested-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
disable_irqs() was mistakenly disabling all interrupts when called.
This cause all port stream to stop even if only stopping one of them.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In future patch, the release of the device will move
to the release callback of v4l2_device. Therefore the
device will be released only when the last fh will be
closed. Dynamic allocation will then be needed since
when the device is unbounded and then bounded again,
it might be that the probe callback will run before
the release of the last device is finished. In that
case both operations will run on the same memory
concurrently and cause memory corruption.
This patch also removes the pdev field of
vimc_device since it is not needed anymore.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
replace 'vimc->pdev.dev' with 'vimc->mdev.dev'
in debug prints and in assignment to
vimc_ent_device.dev. This helps to unify the debug
statements. This will also eliminate the need to use
the pdev field in vimc_device in future patch.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the dma channel request error code is EPROBE_DEFER there is no need to
print error message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Video engine in AST2600 has the exactly same register set with
AST2500 except VR084 register which provides more precise JPEG
size read back. This commit adds support for the difference and
adds 'aspeed,ast2600-video-engine' compatible OF string.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VP9 bitstream specification indicate segment data should reset to
default when meet key frames, intra only frames or enable error
resilience mode. So memset segmentation map buffer before every
decode process is not appropriate.
Reset segment data only when needed, then start decoder hardware
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allwinner A83T contains rotation core which can rotate and flip images.
Add a driver for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: MAINTAINERS paths were out of date, fix that]
[hverkuil-cisco@xs4all.nl: VFL_TYPE_GRABBER -> _VIDEO]
[hverkuil-cisco@xs4all.nl: Fix module build]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, v4l2_pipeline_pm_use() prototype is:
int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.
Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.
It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.
And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ... prevented restarting CCDC through its interrupt handler when
it's about to be disabled. It missed to address the case when CCDC might
be enabled due to queueing a buffer. Do that now.
Fixes: dd12ed17ce ("omap3isp: Don't restart CCDC if we're about to stop")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to use dynamic video codec assignment add a new sdm845-v2
DT compatible and new venus_resource structure to cover the binding
where all pmdomains and clocks are under the venus_core control.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Handle 10bit video streams in the decoder by using dithering, i.e
the decoder output buffers will be in 8bit format.
The runtime handling is implemented by sending v4l2 event to
userspace application, then the application should stop the
streaming on capture queue and initiate format negotiation, and
start streaming again.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Presently the core (vcodec pipelines) assignment is static. Here we
introduce dynamic load balancing across the cores depending on the
current session load. The load on earch core is calculated and core
with minimum load is assigned to given instance. This will be
applicable on Venus v4 with more than one vcodec cores.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Redesign core (vcodec) clock control to give the venus core more
freedom to control them in order to make possible to use core
selection feature on Venus IP v4.
Move all clock and pmdomain functions in separate file and abstract
power control with common operations per Venus IP version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those two properties are not implemented for Venus v4 (sdm845),
thus don't set them to firmware.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace explicit use of members of struct resource by %pR to print
the resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some older MSM8916 Venus firmware versions also seem to indicate
support for encoding HEVC, even though they really can't.
This will lead to errors later because hfi_session_init() fails
in this case.
HEVC is already ignored for "dec_codecs", so add the same for
"enc_codecs" to make these old firmware versions work correctly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ignore errors returned from kthread_stop since the
vimc subdevices should still be notified that
streaming stopped so they can release the memory for
the streaming, and also kthread should be set to NULL.
kthread_stop can return -EINTR in case the thread
did not yet run. This can happen if userspace calls
streamon and streamoff right after.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a mistakenly written self assignment in
`static int vpfe_enum_fmt_vid_cap(..)`.
Fixed it according to Prabhakar Lad's feedback.
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver forgets to disable and unprepare clock when remove.
Add a call to clk_disable_unprepare() to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hardware does not support capturing the field types
V4L2_FIELD_SEQ_TB and V4L2_FIELD_SEQ_BT. To capture in these formats the
driver needs to adjust the offset of the capture buffer and capture
twice to each vb2 buffer.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To support SEQ_TB/BT not all buffers given to the hardware will be
equal, the driver needs to keep track of different buffer types. Move
the tracking of buffers given to hardware into a struct so additional
tracking fields can be associated with each buffer.
[hverkuil: fix small checkpatch warning]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case kthread_run fails, the vimc subdevices
should be notified that streaming stopped so they can
release the memory for the streaming. Also, kthread should be
set to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This exposes the white balance configuration of the ISC as v4l2 controls
into userspace.
There are 8 controls available:
4 gain controls, sliders, for each of the BAYER components: R, B, GR, GB.
These gains are multipliers for each component, in format unsigned 0:4:9
with a default value of 512 (1.0 multiplier).
4 offset controls, sliders, for each of the BAYER components: R, B, GR, GB.
These offsets are added/substracted from each component, in format signed
1:12:0 with a default value of 0 (+/- 0)
To expose this to userspace, added 8 custom controls, in an auto cluster.
To summarize the functionality:
The auto cluster switch is the auto white balance control, and it works
like this:
AWB == 1: autowhitebalance is on, the do_white_balance button is inactive,
the gains/offsets are inactive, but volatile and readable.
Thus, the results of the whitebalance algorithm are available to userspace
to read at any time.
AWB == 0: autowhitebalance is off, cluster is in manual mode, user can
configure the gain/offsets directly. More than that, if the
do_white_balance button is pressed, the driver will perform
one-time-adjustment, (preferably with color checker card) and the userspace
can read again the new values.
With this feature, the userspace can save the coefficients and reinstall
them for example after reboot or reprobing the driver.
[hverkuil: fix checkpatch warning]
[hverkuil: minor spacing adjustments in the functionality description]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the preferred form for GPL2+, and add IBM and Intel as the authors.
The driver was initially upstreamed by Eddie from IBM, and has had major
contributions from Jae at Intel.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The aspeed video IP has some differences between SoC families. Currently
the driver decides which registers to use at compile time, which means
a single kernel can not be used between platforms.
Switch to using runtime configuration of the registers that vary between
SoC families. This is in preparation for upcoming ast2600 support.
[hverkuil: replace ;; by ;]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the recently introduced function devm_platform_ioremap_resource to
save a few lines of code. This makes the driver match common platform
device probe patterns.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isif_config_defaults structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When adding support for NV12 it was overlooked that the pixel format is
only supported on some VIN channels. Fix this by adding a check to only
accept NV12 on the supported channels 0, 1, 4, 5, 8, 9, 12 and 13.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Before extending the special pixel format handling turn the multiple if
statements into a switch.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Only ARGB32-type pixelformat were assumed to have 4 components, which is
wrong since RGB32-type pixelformats may have an alpha channel, so they
should also assume 4 color components.
The XRGB32-type pixelformats really have only 3 color components, but this
complicated matters since that creates strides that are sometimes width * 3
and sometimes width * 4, and in fact this can result in buffer overflows.
Keep things simple by just always processing all 4 color components.
In the future we might want to optimize this again for the XRGB32-type
pixelformats, but for now keep it simple and robust.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v5.4 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
-----BEGIN PGP SIGNATURE-----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=sGdY
-----END PGP SIGNATURE-----
Merge tag 'media/v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New staging driver for Rockship ISPv1 unit
- New staging driver for Rockchip MIPI Synopsys DPHY RX0
- y2038 fixes at V4L2 API (backward-compatible)
- A dvb core fix when receiving invalid EIT sections
- Some clang-specific warnings got fixed
- Added support for touch V4L2 interface at vivid
- Several drivers were converted to use the new
i2c_new_scanned_device() kAPI
- Added sm1 support at meson's vdec driver
- Several other driver cleanups, fixes and improvements
* tag 'media/v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (207 commits)
media: staging/intel-ipu3: remove TODO item about acronyms
media: v4l2-fwnode: Print the node name while parsing endpoints
media: Revert "media: staging/intel-ipu3: make imgu use fixed running mode"
media: mt9v111: constify copied structure
media: platform: VIDEO_MEDIATEK_JPEG can also depend on MTK_IOMMU
media: uvcvideo: Add a quirk to force GEO GC6500 Camera bits-per-pixel value
media: uvcvideo: Avoid cyclic entity chains due to malformed USB descriptors
media: hantro: fix post-processing NULL pointer dereference
media: rcar-vin: Use correct pixel format when aligning format
media: MAINTAINERS: add entry for Rockchip ISP1 driver
media: staging: rkisp1: add TODO file for staging
media: staging: rkisp1: add document for rkisp1 meta buffer format
media: staging: rkisp1: add output device for parameters
media: staging: rkisp1: add capture device for statistics
media: staging: rkisp1: add user space ABI definitions
media: staging: rkisp1: add streaming paths
media: staging: rkisp1: add Rockchip ISP1 base driver
media: staging: phy-rockchip-dphy-rx0: add Rockchip MIPI Synopsys DPHY RX0 driver
media: staging: dt-bindings: add Rockchip MIPI RX D-PHY RX0 yaml bindings
media: staging: dt-bindings: add Rockchip ISP1 yaml bindings
...
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes
-----BEGIN PGP SIGNATURE-----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=oFrI
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
When aligning the format the pixel format that is being processed shall
be used to figure out alignment constraints, not the currently active
pixel format. The alignment might be part of a try operation and shall
not be effected by the active format. Fix this by looking at the correct
pixel format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the newer API returning an ERRPTR and use the new helper to bail
out.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Despite using M2M in both the decoder and encoder, this driver used
vb2_v4l2_buffer as its base buffer structure, and placed a list_head
right after the buffer declaration in order to match the layout of a
v4l2_m2m_buffer. This is very dangerous as it means the driver will
break should the layout of v4l2_m2m_buffer change.
Fix this by directly using v4l2_m2m_buffer and updating the sites that
accessed the buffer accordingly.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In vpfe_register_ccdc_device(), failure to allocate dev->hw_ops
fields calls BUG_ON(). This patch returns the error to callers
instead of crashing. The issue was identified by a static
analysis tool, written by us.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/media/platform/sti/bdisp/bdisp-hw.c, 385:
msleep in bdisp_hw_reset
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341:
bdisp_hw_reset in bdisp_device_run
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317:
_raw_spin_lock_irqsave in bdisp_device_run
To fix this bug, msleep() is replaced with udelay().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl4SYegeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4m4H+QGCUN8SXN+2B+0/
BfzOf7PFoKzAx3NwDbJQIZqhSl+Zfa4n3VGPEF8sXsvoQgdYvuJnS/5JiAZ9iRIH
HAfFzegzQ3mCl8Du+SqCvQKs2Jt4OMCX62KGRebRBhpoKfZdwmN7n7pn9lWO771K
9rxTpeItXhmK46jOFRbi5oyQfmkfSfyUN1b9CB53FXFS+ZDkDNA7QQiIYnKOD7SZ
RrL7czhZ580QOC61qOlnz1GIhRzvU5SXg4OtuI3YfoOJRY5FKC3YtOgLReT0vPs+
vEhAyP93upVXIhqm10WHNjd4t4a45Vy5ff64uFsQ9QV4nnqsC2C70YwWbVDdtz/W
Lm0mvE8=
=NECs
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rc5' into patchwork
Linux 5.5-rc5
* tag 'v5.5-rc5': (1006 commits)
Linux 5.5-rc5
Documentation: riscv: add patch acceptance guidelines
riscv: prefix IRQ_ macro names with an RV_ namespace
clocksource: riscv: add notrace to riscv_sched_clock
apparmor: fix aa_xattrs_match() may sleep while holding a RCU lock
hexagon: define ioremap_uc
ocfs2: fix the crash due to call ocfs2_get_dlm_debug once less
ocfs2: call journal flush to mark journal as empty after journal recovery when mount
mm/hugetlb: defer freeing of huge pages if in non-task context
mm/gup: fix memory leak in __gup_benchmark_ioctl
mm/oom: fix pgtables units mismatch in Killed process message
fs/posix_acl.c: fix kernel-doc warnings
hexagon: work around compiler crash
hexagon: parenthesize registers in asm predicates
fs/namespace.c: make to_mnt_ns() static
fs/nsfs.c: include headers for missing declarations
fs/direct-io.c: include fs/internal.h for missing prototype
mm: move_pages: return valid node id in status if the page is already on the target node
memcg: account security cred as well to kmemcg
kcov: fix struct layout for kcov_remote_arg
...
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The A10/A20 Allwinner SoCs have two camera sensor interface blocks,
named CSI0 and CSI1. The two have the same register layouts with
slightly different features:
- CSI0 has an image signal processor (ISP); CSI1 doesn't
- CSI0 can support up to four separate channels under CCIR656;
CSI1 can only support one
- CSI0 can support up to 16-bit wide bus with YUV422;
CSI1 can support up to 24-bit wide bus with YUV444
For now the driver doesn't support wide busses, nor CCIR656. So the
only relevant difference is whether a clock needs to be taken and
enabled for the ISP.
Add structs to record the differences, tie them to the compatible
strings, and deal with the ISP clock. Support for the new CSI1
hardware block is added as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On Allwinner SoCs, some high memory bandwidth devices do DMA directly
over the memory bus (called MBUS), instead of the system bus. These
devices include the CSI camera sensor interface, video (codec) engine,
display subsystem, etc.. The memory bus has a different addressing
scheme without the DRAM starting offset.
Deal with this using the "interconnects" property from the device tree,
or if that is not available, set dev->dma_pfn_offset to PHYS_PFN_OFFSET.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The omap3isp driver set the new buffer and enabled the CCDC in a situation
a new buffer was available but streaming was about to be stopped on the
CCDC. This lead to frequent system crashes in case there were buffers
queued when streming was being stopped.
Fix this by first checking whether there's an intent to stop streaming and
if there isn't, then set the new buffer and re-enable CCDC.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isp was marked to have failed to stop if stopping streaming on an
external subdev failed. The return value from the external subdev should
be ignored instead as it is not part of the ISP and thus the ISP does not
need to be reset for that reason.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
The v4l2-compliance tests failed with the touch device when multiplanar was
enabled in vivid. Since it is perfectly fine to support the multiplanar API
for touch, add support for this in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_buffer's 'field' value was never initialized in vivid for the
touch capture device, causing v4l2-compliance errors.
Set it to NONE.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the sink pad of scaler subdevice to respond
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION ioctls with the following
targets: V4L2_SEL_TGT_COMPOSE_BOUNDS and V4L2_SEL_TGT_CROP.
* Add new const struct crop_rect_default to initialize subdev scaler
properly.
* Make changes in sink pad format reflect to the crop rectangle. E.g.
changing the frame format to a smaller size one can make the former
crop rectangle selects a non existing frame area. To solve this
situation the crop rectangle is clamped to the frame boundaries.
* Clamp crop rectangle respecting the sink bounds during set_selection
ioctl.
Co-developed-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Signed-off-by: Guilherme Alcarde Gallo <gagallo7@gmail.com>
Signed-off-by: Danilo Figueiredo Rocha <drocha.figueiredo@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISI was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISI width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This adds support for GREY and Y16 formats, based on Y10 mbus codes.
Y16 needs to go through preview path in the ISI, with 2 pixels per word,
and it fits the Y16 format. The ISI data lines need to be MSB aligned with
the sensor data lines.
GREY format in 8 bits per pixel is done by dropping the 2 LSB bits
from the Y10 format, and packed as 4 pixels per word.
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISC was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISC width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With some sensors, the mbus code must match the one that sensor supports.
In this case we should initialize the mbus_code of the fse/fie before
calling the subdev, and not after.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ISC can receive input from sensors using Y10 format directly
(10 bits greyscale). In this case, the ISC must dump the data directly,
either as GREY (8bit) or Y10 (10bit).
Y16 is not supported because we cannot align the MSB 10 bits to the MSB
inside the 16bit container.
For this format, the ISC internal pipeline cannot work (only works with
BAYER), so we must dump the data directly as 8bit/10bit.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case the format that the sensor sends is 8 bit only (like GREY for
example) we need to be able to bypass ISC pipeline and directly dump
8 bits.
That's why the hardcoded value of 16 bpp is not correct in all cases.
This change allows the output format to decide what is the correct bpp
(bits per pixel) such that the result is in the proper format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When decoding using the CODA internal rotator (for example NV12
capture), currently the value vb2_buf.index + CODA_MAX_FRAMEBUFFERS (19)
is written into the DEC_PIC_ROT_INDEX register. At least with firmware
version 3.1.1 this causes CODA hangups as soon as the register value
reaches 32. Instead, always write CODA_MAX_FRAMEBUFFERS.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Both platform_get_irq_byname() and platform_get_irq() already print an
error. Remove the redundant error message.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds JPEG encoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG encoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can encode
4:2:2 subsampled images into JPEGs of the same subsampling.
There are two additional tracepoints added to the coda driver that can
be used together with the v4l2:v4l2_qbuf and v4l2:v4l2_dqbuf tracepoints
to to follow video frames through the mem2mem device when encoding or
decoding with the CODA960 JPEG codec:
coda:coda_jpeg_run
coda:coda_jpeg_done
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
[hverkuil-cisco@xs4all.nl: removed unused k and q_data_dst variables]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CODA960 JPEG codec is controlled directly from the host, there is no
support in the BIT processor firmware. This patch adds the necessary
register definitions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Huffman bits tables are always 16 bytes long, and they are always
followed directly by the values tables, both in hardware and in JPEG
files. Just merge the two tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Always call finish_run when the hardware signals completion. This
will allow JPEG contexts to clean up even if job_abort was called
during the device_run.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In csc_set_coeff() we were previously checking if the format type was
V4L2_BUF_TYPE_VIDEO_OUTPUT or V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE as a
mean to figure out if the format was multiplanar or not. This was not
entirely accurate as the format type could also be a CAPTURE type
instead.
Fix this by removing the 'switch' construct and replacing them with
"if (V4L2_TYPE_IS_MULTIPLANAR(type))" instead.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver forgets to kill tasklet when probe fails and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support to emulate touch devices in vivid driver.
It generates touch patterns simulating single tap, double tap, triple
tap, move from left to right, zoom in, zoom out, palm press simulating
large area being pressed on screen, and simulating 16 different
simultaneous touch points.The values generated are based on
behavior of the rmi_f54 driver.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver misses destroying wdt_wq when remove like what is done when
probe fails.
Add the missed calls like what is done to job_wq to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver forgets to call destroy_workqueue when remove and probe fails.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Make sure that both enum_mbus_code() and enum_framesize() properly
populate the .which parameter member, otherwise -EINVAL is return
causing the subdev asynchronous registration handshake to fail.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When start_streaming fails after the buffers have been queued we have to
make sure all buffers are returned to user-space properly otherwise a
v4l2 level WARN is generated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we were using an arbitrarily small maximum resolution mostly
based on available sensor capabilities. However the hardware DMA limits
are much higher than the statically define maximum resolution we were
using.
There we rework the boundary check code to handle the maximum width and
height based on the maximum line width in bytes and re-calculating the
pixel width based on the given pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because V4L2 still uses a specific way to manage power state of devices
that predates runtime PM, bridge driver should power on and off sub
device explicitly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support the AM654
family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support
the DRA76x family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current CSI2 DPHY initialization sequence although
functional does not match with the documented sequence
in the Technical Reference Manual.
This may affect capture re-startability in stop/start
situations.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pixel processing unit was hard coded to only handle 8 bits per pixel
from input to output.
We now add handling for 10, 12 and 16 bits per pixel at the source and
setting the in-memory size (i.e. container size) to 16 bits for these 3
cases.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current method to calculate the ddr clk period is wrong.
Therefore the ths_term calculation is incorrect.
Also it was wrongly assumed that the ths_settle parameter
was based on the control clock instead of the pixel clock.
Since the DPHY can tolerate quite a bit a of variation,
capture was still mostly working with the 2 tested modes
when the pixel clock was close to the control clock
(i.e. 96 Mhz). But it would quickly stops working when
using different modes or when customers used different
sensors altogether.
Calculating the DDRClk period needs to take into account
the pixel bit width and the number of active data lanes.
Based on the latest technical reference manual these
parameters should now be calculated as follows:
THS_TERM: Programmed value = floor(20 ns/DDRClk period)
THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4
Also originally 'depth' was used to represent the number of
bits a pixel would use once stored in memory (i.e. the
container size). To accurately calculate the THS_* parameters
we need to use the actual number of bits per pixels coming
in from the sensor. So we are renaming 'depth' to 'bpp' (bits
per pixels) and update the format table to show the actual
number of bits per pixel being received.
The "container" size will be derived from the "bpp" value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Apply Errata i913 every time the functional clock is enabled.
This should take care of suspend/resume case as well.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.
This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.
Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow CAL to be able to export DMA buffer.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
First this patch adds a method to access the CTRL_CORE_CAMERRX_CONTROL
register to use the syscon mechanism. For backward compatibility we also
handle using the existing camerrx_control "reg" entry if a syscon node
is not found.
In addition the register bit layout for the CTRL_CORE_CAMERRX_CONTROL
changes depending on the device. In order to support this we need to use
a register access scheme based on data configuration instead of using
static macro.
In this case we make use of the regmap facility and create data set
based on the various device and phy available.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Looks like the preferred macro to define a single bit mask is BIT() and
not BIT_MASK().
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings for CAL_HL_IRQ_MASK]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Hj7G
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
* patchwork: (360 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
This reverts commit 3192b2ca79.
There are indications that this patch causes problems on some
platforms due to some hardware prefetch. Reverting this patch
for now until this is better understood.
Reported-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Update the compatible string to match the updated bindings.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable output side crop selections for the decoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1576): IS_DECODER(node)
test Cropping: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable capture side compose selections for the encoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1662): IS_ENCODER(node)
test Composing: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the implementation of aspeed_video_probe() the allocated memory for
video should be released if either devm_ioremap_resource()
or aspeed_video_init() or aspeed_video_setup_video() fails. Replace
kzalloc() with devm_kzalloc to avoid explicit release for video.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The irqlock spinlock has been unused from the start. Remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_compat_ioctl32() is the function that calls into
v4l2_file_operations->compat_ioctl32(), so setting that back to the same
function leads to a trivial endless loop, followed by a kernel
stack overrun.
Remove the incorrect assignment.
Cc: stable@vger.kernel.org
Fixes: 7472c1c691 ("[media] media: venus: vdec: add video decoder files")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The field kthread_sen in the vimc_sen_device is
not set and used. So remove the field and
the code that check if it is non NULL
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Cc: <stable@vger.kernel.org> # for v5.4 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This control represents a generic read/write area.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When driver is built as module and probe during insmod is deferred
because of sensor subdevs, there is NULL pointer deference because
mdev is cleaned up and then access it from v4l2_device_unregister().
Fix the wrong mdev and v4l2 dev order in error path of probe.
This fixes below null pointer deference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ca026f68
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[...]
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at ida_free+0x7c/0x160
LR is at xas_start+0x44/0x204
[...]
[<c0dafd60>] (ida_free) from [<c083c20c>] (__media_device_unregister_entity+0x18/0xc0)
[<c083c20c>] (__media_device_unregister_entity) from [<c083c2e0>] (media_device_unregister_entity+0x2c/0x38)
[<c083c2e0>] (media_device_unregister_entity) from [<c0843404>] (v4l2_device_release+0xd0/0x104)
[<c0843404>] (v4l2_device_release) from [<c0632558>] (device_release+0x28/0x98)
[<c0632558>] (device_release) from [<c0db1204>] (kobject_put+0xa4/0x208)
[<c0db1204>] (kct_put) from [<bf00bac4>] (fimc_capture_subdev_unregistered+0x58/0x6c [s5p_fimc])
[<bf00bac4>] (fimc_capture_subdev_unregistered [s5p_fimc]) from [<c084a1cc>] (v4l2_device_unregister_subdev+0x6c/0xa8)
[<c084a1cc>] (v4l2_device_unregister_subdev) from [<c084a350>] (v4l2_device_unregister+0x64/0x94)
[<c084a350>] (v4l2_device_unregister) from [<bf0101ac>] (fimc_md_probe+0x4ec/0xaf8 [s5p_fimc])
[...]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fixes: 9832e155f1 ("[media] media-device: split media initialization and registration")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().
These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
/* shutdown control thread */
vivid_grab_controls(dev, false);
mutex_unlock(&dev->mutex);
kthread_stop(dev->kthread_vid_cap);
dev->kthread_vid_cap = NULL;
mutex_lock(&dev->mutex);
But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.
To fix those issues let's:
1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Refactor some of the vivid_create_instance code by using a
new vivid_create_queue() helper function.
Also add some sanity checks for the node_types vs input/output_types
module options.
This patch resolves these two smatch parse errors:
drivers/media/platform/vivid/vivid-core.c:1679 vivid_create_instance() parse error: OOM: 3002600Kb sm_state_count = 6160113
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:1679
vivid_create_instance() parse error: __split_smt: function too hairy. Giving up after 33 seconds
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch fixes this error:
drivers/media/platform/ti-vpe/vpdma.c:767 dump_dtd() error: '%pad' expects argument of type 'dma_addr_t*', argument 2 has type 'uint*'
dtd->start_addr is a u32, so no need for %pad.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes this warning:
drivers/media/platform/am437x/am437x-vpfe.c:288 vpfe_ccdc_validate_param() warn: unsigned 'ccdcparam->alaw.gamma_wd' is never less than zero.
by dropping the gamma_wd < VPFE_CCDC_GAMMA_BITS_15_6 check
since VPFE_CCDC_GAMMA_BITS_15_6 is 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of validating the links to capture devices and subdevices with
the same function, use the default v4l function for links between
subdevices and only use a different function for validating between
capture device and subdevice.
This change should also ease future work to associate multiple mbus
codes for the same pixelformat in vimc_pix_map.
These changes were tested with
v4l2-compliance SHA: 3f806630e2ecbcebe31872b865c5c4b42f111a99, 64 bits
and passed all tests:
Grand Total for vimc device /dev/media0: 451, Succeeded: 451, Failed: 0, Warnings: 0
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@protonmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of components are only set, and never used.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The official name is "R-Car M3-N", not "R-Car M3N".
Fixes: 4e8c120de9 ("media: fdp1: Support M3N and E3 platforms")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel driver never touches the decoded buffers with the CPU.
All accesses are either done by hardware DMA masters or userspace
mapping the buffers. This means we don't need a kernel virtual
address mapping for those buffers at all. As those buffers are
usually quite large, we can save a good deal of kernel vmalloc
space by requesting to not have a kernel mapping set up for them.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The BIT decoder picture run temporarily locks the bitstream mutex while
the coda device mutex is locked, to refill the bitstream ring buffer.
Consequently, the decoder start command, which locks both mutexes when
flushing the bitstream ring buffer, must lock the coda device mutex
first as well, to avoid an ABBA deadlock.
Fixes: e7fd95849b ("media: coda: flush bitstream ring buffer on decoder restart")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.
Fixes: 1380f5754c ("[media] videobuf2: Add missing lock held on vb2_fop_release")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
"f->fmt.sdr.reserved" is uninitialized. As other peer drivers
like msi2500 and airspy do, the fix initializes it to avoid
memory disclosures.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2N(R8A774B1) SoC.
The CSI-2 module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the SoC specific information for RZ/G2N(R8A774B1) SoC.
The VIN module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most Gen3 boards can output frames in NV12 format, add support for this
with a runtime check that the running hardware supports it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most but not all Gen3 hardware support outputting NV12, add a flag to
indicate which SoCs do support it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a pixel format is not supported by the hardware NULL is returned by
rvin_format_from_pixel() for that fourcc. Verify that the pixel format
is supported using this or skip it when enumerating.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a process is interrupted while accessing the video device and the
device lock is contended, release() could return early and fail to free
related resources.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes: 28ffeebbb7 ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Cc: stable <stable@vger.kernel.org> # 4.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch corrects the SPDX License Identifier style
in header files related to Video drivers for Xilinx devices.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allwinner H3 SoC contains deinterlace unit, which has several modes of
operation - bypass, weave, bob and mixed (advanced) mode. I don't know
how mixed mode works, but according to Allwinner it gives best results,
so they use it exclusively. Currently this mode is also hardcoded here.
For each interleaved frame queued, this driver produces 2 deinterlaced
frames. Deinterlaced frames are based on 2 consequtive output buffers,
except for the first 2, where same output buffer is given to peripheral
as current and previous.
There is no documentation for this core, so register layout and fixed
values were taken from BSP driver.
I'm not sure if maximum size of the image unit is capable to process is
governed by size of "flag" buffers, frequency or it really is some HW
limitation. Currently driver can process full HD image in ~15ms (7.5ms
for each capture buffer), which allows to process 1920x1080@60i video
smoothly in real time.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: add static to deinterlace_ioctl_ops]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add mean window size parameter for debayer filter as a control in
vimc-debayer.
vimc-debayer was patched to allow changing mean window parameter
of the filter without needing to reload the driver. The parameter
can now be set using a v4l2-ctl control(mean_window_size).
Co-developed-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Arthur Moraes do Lago <arthurmoraeslago@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the 'struct device *dev' field exists in each of the
entity structs, it can be moved to the common struct vimc_ent_devevice.
It is then used to replace 'pr_err' with 'dev_err' in the streamer
code.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since the pads array is of known small size, there is no reason to
allocate it separately. Instead, it is embedded in the entity struct.
This also conforms to the media controller doc:
'Most drivers will embed the pads array in a driver-specific structure,
avoiding dynamic allocation.'
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
[hverkuil-cisco@xs4all.nl: remove unused vimc_pads_init()]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
the struct vimc_platform_data is not used anymore and can be removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'vimc_pipeline_s_stream' is not used and can be
removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc is a single kernel module and does not need to
export any symbols therefore there is no need for these
declarations.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since this function only calls v4l2_device_unregister_subdev,
it is pointless.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
according to the docs, this function must be called during
the cleanup phase after unregistering the entity.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc_sen_add function first registers the subdevice and then
calls tpg_alloc. If tpg_alloc fails it unregisters the subdevice
and then frees vsen, this cause double free since the release
callback that follows subdevice unregistration also frees vsen.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the add callback returns NULL on failure and the array
is initialized to NULLs, there is no need for the intermediate
assignment to local var.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since NULL value for vimc entity pointer indicates
that entity creation failed and this is tested, the
pointers should be initialized to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the Kconfig dependency to CONFIG_PREEMPTION.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There appears to be a copy-paste error on the access of
csc_coeffs.y2r.r601.full.coeff, I believe csc_coeffs.2yr.r601.full.coeff
should be used instead. This is a moot point as the code is never
reached, but at least use the correct structure element.
Addresses-Coverity: ("Copy-paste error")
Fixes: 3ff3a712a9 ("media: ti-vpe: vpe: don't rely on colorspace member for conversion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes it detects a weird resolution such as 1024x287 when the
actual resolution is 1024x768. To resolve such an issue, this
commit adds clearing for hsync and vsync polarity register bits
at the beginning of the first mode detection. This is recommended
in the datasheet.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prevent inaccurate detections of resolution, this commit enables
clearing of hsync/vsync polarity bits based on probed sync state.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support metadata output in vivid driver.
Metadata output is used to set brightness, contrast, saturation
and hue.
Adds new files for metadata output.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds meatadata capture support in vivid driver.
Adds new files for metadata capture.
Adds vivid controls to generate PTS and SCR for metadata stream.
also fixes v4l2-compliance issues seen on metadata device.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Up to now VPE was relying on the colorspace value of struct v4l2_format
as an indication to perform color space conversion from YUV to RGB or
not.
Instead we should used the source/destination fourcc codes as a more
reliable indication to perform color space conversion or not.
To do so, we rework the csc module to use "struct v4l2_format *" as
parameters, and reorganize the coefficients tables in a more logical
way.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The RGB to YUV HD full range coefficients did not match the TRM values
and appeared to be a cut-n-paste from the YUV to RGB section.
Replace the entries with the values from the TRM.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All 4 of the "colorspace" components were not originally handled.
Causing issue related to xfer_func not being initialized properly.
This was found with v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For each queue we need to maintain resolutions, pixel format,
bytesperline, sizeimage, colorspace, etc.
Instead of manually adding more entries in the vpe_q_data struct, it is
better to just add a "struct v4l2_format" member and use that to store
all needed information.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil@xs4all.nl: fix checkpatch warning]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE uses VPDMA (built-in dma engine) to transfer data to and from the IP
and memory. VPDMA expect 32 bits addresses. To make sure that is always
the case set the DMA mask and coherent mask for the device.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using dma_addr_t as the type to hold address inside of a fix sized
descriptor used by the vpdma firmware is prone to fail when the expected
width is 32 bits and suddenly when CONFIG_LPAE is enabled the data size
is now 64 bits shifted the remaining members of the descriptor in memory
which confuses the firmware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(691): ret == 0
fail: v4l2-test-buffers.cpp(974): captureBufs(node, q, m2m_q,
frame_count, true)
test MMAP: FAIL
This caused the following Kernel Warning:
WARNING: CPU: 0 PID: 961 at
drivers/media/v4l2-core/videobuf2-core.c:1658
__vb2_queue_cancel+0x174/0x1d8
...
CPU: 0 PID: 961 Comm: v4l2-compliance Not tainted
4.14.62-01720-g20ecd717e87a #6
Hardware name: Generic DRA72X (Flattened Device Tree)
Backtrace:
[<c020b5bc>] (dump_backtrace) from [<c020b8a0>] (show_stack+0x18/0x1c)
r7:00000009 r6:60070013 r5:00000000 r4:c1053824
[<c020b888>] (show_stack) from [<c09232e8>] (dump_stack+0x90/0xa4)
[<c0923258>] (dump_stack) from [<c022b740>] (__warn+0xec/0x104)
r7:00000009 r6:c0c0ad50 r5:00000000 r4:00000000
[<c022b654>] (__warn) from [<c022b810>] (warn_slowpath_null+0x28/0x30)
r9:00000008 r8:00000000 r7:eced4808 r6:edbc9bac r5:eced4844
r4:eced4808
[<c022b7e8>] (warn_slowpath_null) from [<c0726f48>]
(__vb2_queue_cancel+0x174/0x1d8)
[<c0726dd4>] (__vb2_queue_cancel) from [<c0727648>]
(vb2_core_queue_release+0x20/0x40)
r10:ecc7bd70 r9:00000008 r8:00000000 r7:edb73010 r6:edbc9bac
r5:eced4844
r4:eced4808 r3:00000004
[<c0727628>] (vb2_core_queue_release) from [<c0729528>]
(vb2_queue_release+0x10/0x14)
r5:edbc9810 r4:eced4800
[<c0729518>] (vb2_queue_release) from [<c0724d08>]
(v4l2_m2m_ctx_release+0x1c/0x30)
[<c0724cec>] (v4l2_m2m_ctx_release) from [<bf0e8f28>]
(vpe_release+0x74/0xb0 [ti_vpe])
r5:edbc9810 r4:ed67a400
[<bf0e8eb4>] (vpe_release [ti_vpe]) from [<c070fccc>]
(v4l2_release+0x3c/0x80)
r7:edb73010 r6:ed176aa0 r5:edbc9868 r4:ed5119c0
[<c070fc90>] (v4l2_release) from [<c033cf1c>] (__fput+0x8c/0x1dc)
r5:ecc7bd70 r4:ed5119c0
[<c033ce90>] (__fput) from [<c033d0cc>] (____fput+0x10/0x14)
r10:00000000 r9:ed5119c0 r8:ece392d0 r7:c1059544 r6:ece38d80
r5:ece392b4
r4:00000000
[<c033d0bc>] (____fput) from [<c0246e00>] (task_work_run+0x98/0xb8)
[<c0246d68>] (task_work_run) from [<c022f1d8>] (do_exit+0x170/0xa80)
r9:ece351fc r8:00000000 r7:ecde3f58 r6:ffffe000 r5:ece351c0
r4:ece38d80
[<c022f068>] (do_exit) from [<c022fb6c>] (do_group_exit+0x48/0xc4)
r7:000000f8
[<c022fb24>] (do_group_exit) from [<c022fc00>]
(__wake_up_parent+0x0/0x28)
r7:000000f8 r6:b6c6a798 r5:00000001 r4:00000001
[<c022fbe8>] (SyS_exit_group) from [<c0207c80>]
(ret_fast_syscall+0x0/0x4c)
These warnings are caused by buffers which not properly cleaned
up/release during an abort use case.
In the abort cases the VPDMA desc buffers would still be mapped and the
in-flight VB2 buffers would not be released properly causing a kernel
warning from being generated by the videobuf2-core level.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(463): !pfmt.sizeimage
fail: v4l2-test-formats.cpp(736): \
Video Capture Multiplanar is valid, \
but TRY_FMT failed to return a format
test VIDIOC_TRY_FMT: FAIL
This failure is causd by the driver failing to handle out range
'bytesperline' values from user space applications.
VPDMA hardware is limited to 64k line stride (16 bytes aligned, so 65520
bytes). So make sure the provided or calculated 'bytesperline' is
smaller than the maximum value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
test VIDIOC_TRY_FMT: FAIL
This causes the following kernel panic:
Unable to handle kernel paging request at virtual address 56595561
pgd = ecd80e00
*pgd=00000000
Internal error: Oops: 205 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 930 Comm: v4l2-compliance Not tainted \
4.14.62-01715-gc8cd67f49a19 #1
Hardware name: Generic DRA72X (Flattened Device Tree)
task: ece44d80 task.stack: ecc6e000
PC is at __vpe_try_fmt+0x18c/0x2a8 [ti_vpe]
LR is at 0x8
Because the driver fails to properly check the 'num_planes' values for
proper ranges it ends up accessing out of bound data causing the kernel
panic.
Since this driver only handle single or dual plane pixel format, make
sure the provided value does not exceed 2 planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE's max height supported MAX_H is set to 1184 which is the
padded height from VC1 decoder output.
In case of 90, 270 degree rotated video processing, input to
VPE will be 1080x1920, 720x1280 etc and MAX_H needs to be set
correct value. Setting MAX_H to 2048 as worst case height.
Signed-off-by: Ram Prasad <x0038811@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In NV21 format, the chroma plane is written to memory such that the U
and V components are swapped for NV12.
Create a new entry in the VPDMA formats to describe the correct data
types used in the data descriptors.
Update all checks for NV12 and add NV21 there as well.
Add support for V4L2_PIX_FMT_NV21 format for both capture and output
streams.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
SEQ_BT indicates the buffer for bottom field needs to be processed
before the top field.
Simplify the field selection logic to support SEQ_BT as well.
Modify the interlace flags to include any of alternate, SEQ_TB, SEQ_BT.
Update other format error checking to consider SEQ_BT.
Replace SEQ_TB with SEQ_XX wherever applicable.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of saving a pointer to the 'fh' member of struct vpe_ctx to
later have to use container_of to retrieve the actual pointer to the
context structure, which seems to confuse static code analysis tool
anyways, just save the pointer to the actual structure and then retrieve
it directly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user
specified stride") and commit da4414eaed ("[media] media: ti-vpe: vpdma:
add support for user specified stride") resulted in the Motion Vector
stride to be the same as the image stride.
This caused memory corruption in the output image as mentioned in
commit 00db969964 ("[media] media: ti-vpe: vpe: Fix line stride
for output motion vector").
Fixes: 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user specified stride")
Fixes: da4414eaed ("[media] media: ti-vpe: vpdma: add support for user specified stride")
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When TI CAL was introduce as another driver under platform/ti-vpe
adding a second entry into the ti-vpe directory in the platform
Makefile caused issues during parallel build.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simplify these function implementations by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The image size is doubled for NV16 and is calculated as bytesperline *
height * 2 to accommodate the split of UV data. When writing the offset
to hardware, the width is used instead of bytesperline, fix this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rectangle used to correct the compose settings when changing the
format was created inside a helper function and not where it was used.
This is confusing and makes the code harder to read, fix this.
This cleanup is made possible due to refactoring elsewhere and there is
no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After recent refactoring the rectangle named crop no longer reflects it
usage, to contain the source rectangle. Fix this by renaming it. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f13d5f3619 ("media: vimc: Collapse component structure into a single monolithic driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The 2nd parameter of 'find_first_zero_bit()' is a number of bits, not of
bytes. So use 'csi2rx->max_lanes' instead of 'sizeof(lanes_used)'.
Fixes: 1fc3b37f34 ("media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As reported by jenkins@linuxtv.org, the build with i386 fails
with:
ld: drivers/media/platform/qcom/venus/helpers.o: in function `venus_helper_load_scale_clocks':
(.text+0x1d77): undefined reference to `__udivdi3'
ld: (.text+0x1dce): undefined reference to `__udivdi3'
make: *** [Makefile:1094: vmlinux] Error 1
That's because it divides an u32 bit integer by a u64 one.
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is possible for one HDMI connector to have multiple CEC adapters. The
typical real-world scenario is that where one adapter is used when the
device is in standby, and one that's better/smarter when the device is
powered up.
The cec-notifier changes were made with that in mind, but I missed that in
order to support this you need to tell cec_notifier_cec_adap_unregister()
which adapter you are unregistering from the notifier.
Add this additional argument. It is currently unused, but once all drivers
use this, the CEC core will be adapted for these use-cases.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e9fc8740-6be6-43a7-beee-ce2d7b54936e@xs4all.nl
When probed after the HDMI notifier, calling cec_notifier_cec_adap_register()
calls the enable() adapter callback, but the HW is not yet set up.
Moving cec_notifier_cec_adap_register() right before cec_register_adapter()
fixes the following crash:
Ignoring spurious kernel translation fault at virtual address 0000000000000008
[...]
Hardware name: Khadas VIM (DT)
[...]
pc : __do_kernel_fault+0xdc/0x120
lr : __do_kernel_fault+0xdc/0x120
[...]
Call trace:
__do_kernel_fault+0xdc/0x120
do_page_fault+0x180/0x458
do_translation_fault+0x64/0x70
do_mem_abort+0x3c/0x98
el1_da+0x20/0x94
meson_ao_cec_adap_enable+0x30/0x218 [ao_cec]
__cec_s_phys_addr+0x184/0x270
cec_s_phys_addr+0x44/0x60
cec_notifier_cec_adap_register+0x68/0x90
meson_ao_cec_probe+0xb0/0x288 [ao_cec]
[...]
el0_svc_compat+0x8/0x10
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 20958f9d5c ("media: meson/ao-cec: use cec_notifier_cec_adap_(un)register")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Current clock scaling calculations are same for vpu4 and
previous versions. For vpu4, Clock scaling calculations
are updated with cycles/mb and bitrate. This helps in
getting precise clock required.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vpp cycles for different types of codec.
It indicates the cycles required by video hardware
to process each macroblock. Add vsp cycles, cycles
required by stream processor. Initialize the codec
data with core resources.
Signed-off-by: Aniket Masule <amasule@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Failure to suspend (venus_suspend_3xx) happens when the system
is fresh booted and loading venus driver. This happens once and
after reload the venus driver modules the problem disrepair.
Fix the failure by skipping the check for WFI and IDLE bits if
PC_READY is on in control status register.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This aims to add a requests for bandwidth scaling depending
on the resolution and framerate (macroblocks per second). The
exact value of the requested bandwidth is get from a
pre-calculated tables for encoder and decoder.
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In downstream driver, there are two frequency tables defined,
one for the encoder and one for the decoder:
/* Encoders /
<972000 490000000 0x55555555>, / 4k UHD @ 30 /
<489600 320000000 0x55555555>, / 1080p @ 60 /
<244800 150000000 0x55555555>, / 1080p @ 30 /
<108000 75000000 0x55555555>, / 720p @ 30 */
/* Decoders /
<1944000 490000000 0xffffffff>, / 4k UHD @ 60 /
< 972000 320000000 0xffffffff>, / 4k UHD @ 30 /
< 489600 150000000 0xffffffff>, / 1080p @ 60 /
< 244800 75000000 0xffffffff>; / 1080p @ 30 */
It shows that encoder always needs a higher clock than decoder.
In current venus driver, the unified frequency table is aligned
with the downstream decoder table which causes performance issues
in encoding scenarios. Fix that by aligning frequency table on
worst case (encoding).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for cec-notifier to the cec-gpio driver.
This makes it possible to associate the CEC gpio pin with an HDMI
connector. This feature was always documented in the cec-gpio bindings:
Documentation/devicetree/bindings/media/cec-gpio.txt
But support for the hdmi-phandle property was never actually implemented in
this driver.
This patch adds support for this property.
It also fixes a few incorrect error returns in the probe() function, which
skipped the call to cec_delete_adapter().
Tested on a Raspberry Pi 3B with a modified vc4 driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware is capable to passing V4L2_FIELD_ALTERNATE to user-space.
Allow users to request this field format but still default to using the
hardware interlacer if alternating is not explicitly requested.
Before this change a sensor providing data using alternate would be
always combined to an interlaced frame. After this change the user can
request to receive frames as alternate if the sensor provides it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The crop and compose rectangles are reset when s_fmt is called
resulting in potentially valid rectangles being lost when updating the
format. Fix this by mapping the rectangles inside the new format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable to hold the video source information dimensions was poorly
named 'source'. This is confusing as a lot of other members of structs
share the same name with different purposes, rename it src_rect in
preparation of refactoring code.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_FIELD_IS_INTERLACED() can be used to make the code more
readable, use it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While refactoring code the return statement became corrupted, fix it by
returning the correct return code.
Reported-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 897e371389 ("media: rcar-vin: simplify how formats are set and reset"
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, if start streaming -> stop streaming -> start streaming
sequence is executed, driver will end job prematurely, if ctx->translen
is higher than 1, because "aborting" flag is still set from previous
stop streaming command.
Fix that by clearing "aborting" flag in start streaming handler.
Fixes: 96d8eab5d0 ("V4L/DVB: [v5,2/2] v4l: Add a mem-to-mem videobuf framework test device")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vbi stream is started, followed by video streaming,
the vid_cap_streaming and vid_out_streaming were not being set to true,
which would cause the video stream to stop when vbi stream is stopped.
This patch allows to set vid_cap_streaming and vid_out_streaming to true.
According to Hans Verkuil it appears that these 'if (dev->kthread_vid_cap)'
checks are a left-over from the original vivid development and should never
have been there.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check for a potentially NULL pointer that was overlooked and use shorter
accessors to the same data. While we are at it, sprinkle a few comments.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each of the supported decoder formats used to set the same RPC
interrupt handler by themselves, even though this could be done
by the IF init function itself. Move it to the right place and stop
making its symbol public.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mtk_q_data::fmt is actually a pointer and must be dereferenced as such.
This went under the radar because mtk_v4l2_debug() evaluates to nothing
unless DEBUG is defined.
[acourbot: split into its own commit]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array 'registers' on the stack but instead make it
static const. Makes the object code smaller by 45 bytes.
Before:
text data bss dec hex filename
17364 5000 0 22364 575c platform/s3c-camif/camif-regs.o
After:
text data bss dec hex filename
17255 5064 0 22319 572f platform/s3c-camif/camif-regs.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the beginning of the probe function, we have a call to
'request_muxed_region(BRA_SMB_BASE_ADDR, 7, "CEC00001")()'
A corresponding 'release_region()' is performed in the remove function but
is lacking in the error handling path.
Add it.
Fixes: b03c2fb97a ("media: add SECO cec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bus related static data included in the vpfe_fmt
static table can be derived dynamically instead.
This simplify the table and it's use.
We instead replace the per bus data info with just
the usual bit per pixel value for each supported
pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The try_fmt was not actually trying out the provided format
but merely returning the current format basically like get_fmt.
In addition set_fmt should first invoked try_fmt to validate the
given format before applying it to the hardware.
To fix all of these the whole get/try/set ioctl functions had to
be reworked.
When calculating the bytesperline/stride and sizeimage format
member we don't need to locally store the current value of
bytesperpixel as it can easily get derived dynamically.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
checkpatch.pl nows reports several:
WARNING: Prefer using '"%s...", __func__' to using '<function name>',
this function's name, in a string.
So fix these for the whole driver.
At the same time remove the function entry trace log as those can be
enabled using ftrace instead.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using a statically defined format array would cause issue when
multiple vpfe instance would be connected to sub-device of
different capabilities. We need to use an instance based array
instead to properly maintain a per port/instance format list.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VIDIOC_S_STD should not return an error if the value is identical
to the current one.
This error was highlighted by the v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Returning queued vb2 buffers back to user space is a common
task best handled by a helper function.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming fails the h/w module might be left enabled
inadvertently. Make sure it is disabled in the error path.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We were originally attempting to stop all processing as soon
as possible, but the in-progress DMA operation cannot be canceled.
This led to the module being in a busy state and prevented proper
power management functionality.
The existing implementation would attempt to clean things up by waiting
up to 50ms. However when receiving video frame at 15fps or lower,
it meant an inter frame arrival rate of 66.6 ms or higher.
In such cases upon tear down the following message could be seen:
omap_hwmod: vpfe0: _wait_target_disable failed
This patch fixes this issue by adding a stopping state where
we would wait for the next Vsync before disabling the hardware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Previous generation of this driver were hard coded to handle
encoder/decoder where the first line never contains any data and
was therefore always skipped, however when dealing with actual
camera sensors the first line is always present.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently if vpfe is not active then it returns immediately in the
suspend and resume handlers. Change this so that it always performs the
pinctrl config so that we can still get proper sleep state configuration
on the pins even if we do not need to worry about fully saving and
restoring context.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move duplicated IS_SRC and IS_SINK dfines to common header. Rename
them to VIMC_IS_SRC and VIM_IS_SINK.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc uses Component API to split the driver into functional components.
The real hardware resembles a monolith structure than component and
component structure added a level of complexity making it hard to
maintain without adding any real benefit.
The sensor is one vimc component that would makes sense to be a separate
module to closely align with the real hardware. It would be easier to
collapse vimc into single monolithic driver first and then split the
sensor off as a separate module.
Collapse it into a single monolithic driver removing the Component API.
This patch removes the component API and makes minimal changes to the
code base preserving the functional division of the code structure.
Preserving the functional structure allows us to split the sensor off
as a separate module in the future.
Major design elements in this change are:
- Use existing struct vimc_ent_config and struct vimc_pipeline_config
to drive the initialization of the functional components.
- Make vimc_device and vimc_ent_config global by moving them to
vimc-common.h
- Add two new hooks add and rm to initialize and register, unregister
and free subdevs.
- All component API is now gone and bind and unbind hooks are modified
to do "add" and "rm" with minimal changes to just add and rm subdevs.
- vimc-core's bind and unbind are now register and unregister.
- Add a new field to vimc_device structure for saving the pointers to
struct vimc_ent_device(s) subdevs create in their "add" hooks. These
get used to create links and removing the subdevs. vimc-core allocates
this array which sized to number of entries in the topology defined in
the vimc_pipeline_config structure.
- vimc-core invokes "add" hooks from its vimc_register_devices().
The "add" hooks remain the same and register subdevs. They don't
create platform devices of their own and use vimc's pdev.dev as
their reference device. Each "add" hook returns pointer to its struct
vimc_ent_device. This is saved in the vimc_device ent_devs array.
- vimc-core invokes "rm" hooks from its unregister to unregister subdevs
and cleanup.
- vimc-core invokes "add" and "rm" hooks with pointer to struct vimc_device
and the corresponding vimc_ent_device saved in the ent_devs.
The following configure and stream test works on all devices.
media-ctl -d platform:vimc -V '"Sensor A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer A":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Sensor B":0[fmt:SBGGR8_1X8/640x480]'
media-ctl -d platform:vimc -V '"Debayer B":0[fmt:SBGGR8_1X8/640x480]'
v4l2-ctl -z platform:vimc -d "RGB/YUV Capture" -v width=1920,height=1440
v4l2-ctl -z platform:vimc -d "Raw Capture 0" -v pixelformat=BA81
v4l2-ctl -z platform:vimc -d "Raw Capture 1" -v pixelformat=BA81
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video1
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video2
v4l2-ctl --stream-mmap --stream-count=100 -d /dev/video3
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=QTT+
-----END PGP SIGNATURE-----
Merge tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new sensor driver for ov5675
- a new platform driver for Allwinner A10 sensor interface
- some new remote controller keymaps
- some cosmetic changes at V4L2 core in order to avoid #ifdefs and to
merge two core modules into one
- removal of bcm2048 radio driver from staging
- removal of davinci_vpfe video driver from staging
- regression fix since Kernel 5.1 at the legacy VideoBuffer version 1
core
- added some documentation for remote controller protocols
- pixel format documentation was split on two files
- lots of other driver improvements and cleanups
* tag 'media/v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (321 commits)
media: videobuf-core.c: poll_wait needs a non-NULL buf pointer
media: sun4i: Make sun4i_csi_formats static
media: imx: remove unused including <linux/version.h>
media: stm32-dcmi: Delete an unnecessary of_node_put() call in dcmi_probe()
media: pvrusb2: qctrl.flag will be uninitlaized if cx2341x_ctrl_query() returns error code
media: em28xx: Fix exception handling in em28xx_alloc_urbs()
media: don't do a 31 bit shift on a signed int
media: use the BIT() macro
media: ov9650: add a sanity check
media: aspeed-video: address a protential usage of an unitialized var
media: vicodec: make life easier for static analyzers
media: remove include stdarg.h from some drivers
v4l2-core: fix coding style for the two new c files
media: v4l2-core: Remove BUG() from i2c and spi helpers
media: v4l2-core: introduce a helper to unregister a i2c subdev
media: v4l2-core: introduce a helper to unregister a spi subdev
media: v4l2-core: move i2c helpers out of v4l2-common.c
media: v4l2-core: move spi helpers out of v4l2-common.c
media: v4l2-core: Module re-organization
media: usbvision: Remove dead code
...
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The sun4i_csi_formats array is only used in sun4i_v4l2.c, so it doesn't
make any sense to have it !static.
[Sakari Ailus: const static -> static const]
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A null pointer would be passed to a call of the function “of_node_put”
immediately after a call of the function “of_graph_get_next_endpoint”
failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On 32-bits archs, a signed integer has 31 bits plus on extra
bit for signal. Due to that, touching the 32th bit with something
like:
int bar = 1 << 31;
has an undefined behavior in C on 32 bit architectures, as it
touches the signal bit. This is warned by cppcheck.
Instead, force the numbers to be unsigned, in order to solve this
issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by cppcheck:
[drivers/media/dvb-frontends/cx24123.c:434]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:87]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
[drivers/media/pci/bt8xx/bttv-input.c:98]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
...
[drivers/media/v4l2-core/v4l2-ioctl.c:1391]: (error) Shifting signed 32-bit value by 31 bits is undefined behaviour
There are lots of places where we're doing 1 << 31. That's bad,
as, depending on the architecture, this has an undefined behavior.
The BIT() macro is already prepared to handle this, so, let's
just switch all "1 << number" macros by BIT(number) at the header files
with has 1 << 31.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> # exynos4-is and s3c-camif
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # omap3isp, vsp1, xilinx, wl128x and ipu3
Reviewed-by: Benoit Parrot <bparrot@ti.com> # am437x and ti-vpe
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While this might not occur in practice, if the device is doing
the right thing, it would be teoretically be possible to have
both hsync_counter and vsync_counter negatives.
If this ever happen, ctrl will be undefined, but the driver
will still call:
aspeed_video_update(video, VE_CTRL, 0, ctrl);
Change the code to prevent this to happen.
This was warned by cppcheck:
[drivers/media/platform/aspeed-video.c:653]: (error) Uninitialized variable: ctrl
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cppcheck incorrectly produces an error here:
[drivers/media/platform/vicodec/vicodec-core.c:1677]: (error) Pointer addition with NULL pointer.
While this is actually a false positive, it doesn't hurt to
reorder the checks to make the code simpler, handling first
the error patch, where no color or alpha components are there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It returns '0' even when a failure happens on jpeg buffer allocation
so this commit fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If an error occurs in this function, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, introduce two labels to perform
the cleanup work.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In fdp1_open(), 'ctx' is allocated through kzalloc(). However, it is not
deallocated if v4l2_ctrl_new_std() fails, leading to a memory leak bug. To
fix this issue, free 'ctx' before going to the 'done' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The older CSI drivers have camera capture interface different from the one
in the newer ones.
This IP is pretty simple. Some variants (one controller out of two
instances on some SoCs) have an ISP embedded, but there's no code that make
use of it, so we ignored that part for now.
[Sakari Ailus: Wrapped a few long lines, set mbus code using a macro.]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Makefile and Kconfig for the sun6i CSI driver are included in the main
Makefile / KConfig file. Since we're going to add a new CSI driver for an
older chip, and the Cedrus driver eventually, it makes more sense to put
those in our directory.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.
Fixes: 195ebc43bf ("[media] V4L: at91: add Atmel Image Sensor Interface (ISI) support")
Signed-off-by: Alexandre Kroupski <alexandre.kroupski@ingenico.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 5d7936b8e2 ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the goto in two
places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When support for the IPMMU is not enabled, the FDP driver may be
probe-deferred multiple times, causing several messages to be printed
like:
rcar_fdp1 fe940000.fdp1: FCP not found (-517)
rcar_fdp1 fe944000.fdp1: FCP not found (-517)
Fix this by reducing the message level to debug level, as is done in the
VSP1 driver.
Fixes: 4710b752e0 ("[media] v4l: Add Renesas R-Car FDP1 Driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_get_next_child() increments the reference count of the returning
device_node. Decrement it in the check if we are using the old or the
new DTB.
Fixes: ba1f1f70c2 ("[media] media: mtk-mdp: Fix mdp device tree")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Houlong Wei <houlong.wei@mediatek.com>
[hverkuil-cisco@xs4all.nl: use node instead of parent as temp variable]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit b6c61a6c37.
The requested pixelformat is being propagated from the capture to the
tpg in the sensor.
This was a bad design choice, as we start having the following issues:
* We set a pixelformat in the capture;
* We set matching media bus formats in the subdevices pads;
* Link validate looks fine (sizes matches, media bus formats matches);
* Issue: if some of the subdevice doesn't know how to generate the
requested pixelformat in the capture, then stream_on fails. This is bad
because capture says it supports that pixelformat, everything looks
fine, but it is not, and there is no way to find it out through the
links.
This patch was implemented so we could request any pixelformat from the
pipeline regardeless of the media bus format configured between pads.
Not all pixelformat can be mapped into a media bus code (e.g.
multiplanar formats), so with this patch we could request those
pixelformats from the tpg.
Solution: map pixelformats to media bus codes as before, and implement
conversions to other pixelformats in the capture to support multiplanar.
So first step to this solution is to revert this patch.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Lucas A. M. Magalhaes <lucmaga@gmail.com>
Tested-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3c1b9ac753.
Required to Revert "media: vimc: propagate pixel format in the stream"
which introduced the stream object in the vimc_ent_device struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Lucas A. M. Magalhaes <lucmaga@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The image stride was adjusted when it was written to hardware and not
when configuring the format. Calculate the correct stride value and
report it to userspace.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert omap_vout to the vb2 framework. After this change
'v4l2-compliance -s' passes all tests.
As usual, this vb2 conversion is a 'big bang' patch and hard to read.
Tested on a Pandaboard and a Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes the following v4l2-compliance failures:
- FIELD_ANY could be returned, which is not allowed.
- JPEG colorspace was set instead of SRGB.
- No control events.
- Empty bus_info in QUERYCAP.
- Overlay format handling wasn't zeroing bitmap/clips and
didn't return the chromakey correctly.
- G_FBUF didn't fill in many of the v4l2_framebuffer values.
Now also return the base address of the corresponding
framebuffer that this overlays.
- Missing ENUM/G/S_OUTPUT ioctls.
- ROTATE/VFLIP controls were added when the HW didn't support them.
With these changes 'v4l2-compliance' passes all non-streaming tests.
Tested on a Pandaboard and a Beagle XM board.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OMAP 4 TRM specifies that when using double-index addressing
the address increases by the ES plus the EI value minus 1 within
a frame. When a full frame is transferred, the address increases
by the ES plus the frame index (FI) value minus 1.
The omap-dma code didn't account for the 'minus 1' in the FI register.
To get correct addressing, add 1 to the src_icg value.
This was found when testing a hacked version of the media m2m-deinterlace.c
driver on a Pandaboard.
The only other source that uses this feature is omap_vout_vrfb.c,
and that adds a + 1 when setting the dst_icg. This is a workaround
for the broken omap-dma.c behavior. So remove the workaround at the
same time that we fix omap-dma.c.
I tested the omap_vout driver with a Beagle XM board to check that
the '+ 1' in omap_vout_vrfb.c was indeed a workaround for the omap-dma
bug.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://lore.kernel.org/r/952e7f51-f208-9333-6f58-b7ed20d2ea0b@xs4all.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
arch/microblaze/ defines out_be32() and in_be32(), so don't do that
again in the driver source.
Fixes these build warnings:
../drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined
../arch/microblaze/include/asm/io.h:50: note: this is the location of the previous definition
../drivers/media/platform/fsl-viu.c:37: warning: "in_be32" redefined
../arch/microblaze/include/asm/io.h:53: note: this is the location of the previous definition
Fixes: 29d7506863 ("media: fsl-viu: allow building it with COMPILE_TEST")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Error h264 bitstreams which picture info are out range of
decoder hardware specification, and no nal start code at the
beginning of the buffer, stop decoding and exit.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for V4L2_PIX_FMT_BGRA/X32 and V4L2_PIX_FMT_RGBA/X32 formats.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cache flags, timestamps and timecode structure of OUTPUT buffers
in per-instance structure array and fill correctly the same when
the CAPTURE buffers are done.
This will make v4l2-compliance decoder streaming test happy.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Correct handling of OUTPUT buffers field and make v4l2-compliance
happy.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This refactors code for start/stop streaming vb2 operations and
adds a state machine handling similar to the one in stateful codec
API documentation. One major change is that now the HFI session is
started on STREAMON(OUTPUT) and stopped on REQBUF(OUTPUT,count=0),
during that time STREAMOFF(CAP,OUT) just flush buffers but doesn't
stop the session. The other major change is that now the capture
and output queues are completely separated.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In most of the cases the client will know better what could be
the maximum size for compressed data buffers. Change the driver
to permit the user to set bigger size for the compressed buffer
but make reasonable sanitation.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Until now we returned num_output_bufs set during reqbuf but
that could be wrong when we implement stateful Codec API. So
get the minimum buffers for capture from HFI. This is supposed
to be called after stream header parsing, i.e. after dequeue
v4l2 event for change resolution.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds three more helper functions:
* for internal buffers reallocation, applicable when we are doing
dynamic resolution change
* for initial buffer processing of capture and output queue buffer
types
All of them will be needed for stateful Codec API support.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This makes hfi_session_init to return an error when it is
already called without a call to hfi_session_deinit.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Export few HFI functions to use them from decoder to implement
more granular control needed for stateful Codec API compliance.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make hfi_flush function to receive an argument for the type
of flush.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Here we export few helper function to use them from decoder to
implement more granular control needed for stateful Codec API
compliance.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Accept the buffer size requested by client and compare it
against driver calculated size and set the maximum to
bitstream plane.
Signed-off-by: Malathi Gottam <mgottam@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert the via-camera to the vb2 framework. With this change this
driver passes all 'v4l2-compliance -s' tests on my OLPC 1.5.
Also tested with the Sugar 'Record' application.
All tests were done under the OLPC official 5.0.8 kernel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
New RGB444, RGB555 and RGB32 variants were recently added. Now also
support them in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit "vivid: reorder CEC allocation and control set-up" missed that the CEC adapter
needs a valid vfd->name, and that was now filled in after the CEC adapter was
created, leading to an empty adapter name.
Fill in the name earlier.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that both Gen2 (video device centric) and Gen3 (media device
centric) modes of the driver have controls it is required to always
setup the controls when opening the devices. Remove the check which only
calls v4l2_ctrl_handler_setup() for Gen2 and call it unconditionally.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The R-Car VIN module supports V4L2_PIX_FMT_ARGB555 and
V4L2_PIX_FMT_ABGR32 pixel formats. Add the hardware register setup and
allow the alpha component to be changed while streaming using the
V4L2_CID_ALPHA_COMPONENT control.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warning for macro VNDMR_A8BIT]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to adding support for RGB pixel formats with an alpha
component add a control to allow the user to control which alpha value
should be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The value have nothing to do with ARGB1555, it controls if the alpha
component should be filled in for ARGB1555 or ARGB888. Rename it to
reflect this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework OF endpoint parsing for the omap3isp driver. This does add some
lines of code. The benefits are still clear:
- the great complication related to callbacks in endpoint parsing is gone;
instead endpoints are obtained port by port and
- endpoints may now have a default bus configuration which was not
possible while using callbacks. This driver does not benefit from that
feature, but as the omap3isp is one of the exemplary drivers, this works
as an example for driver developers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_async_notifier_add_fwnode_subdev() did not take a reference of
the added fwnode, relying on the caller to handle that instead, in essence
putting the fwnode to be added if there was an error.
As the reference is eventually released during the notifier cleanup, this
is not intuitive nor logical. Improve this by always getting a reference
when the function succeeds, and the caller releasing the reference when it
does not *itself* need it anymore.
Luckily, perhaps, there were just a handful of callers using the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The davinci-vpif driver dereferences its local endpoints after releasing
the reference to them.
The driver also puts its endpoints explicitly while the
of_graph_get_next_endpoint() does that, too, leading to obtaining a
reference once and releasing it twice.
Both are fixed by this patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for CSI2TX v2.1 version of the controller.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes mapping of lanes in DPHY_CFG register
of the controller. In the register, bit 0 means first data lane.
In Linux we currently assume lane 0 is clock.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds lane checks for CSI2TX, to prevent clock lane
being used as a data lane.
Signed-off-by: Jan Kotas <jank@cadence.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an extra condition to add the video output control class when the
device has some hdmi outputs defined. This is required to then always
be able to add the display present control, which is enabled when
there are some hdmi outputs.
This fixes the corner case where no_error_inj is enabled and the
device has no frame buffer but some hdmi outputs, as otherwise the
video output control class would be added anyway. Without this fix,
the sanity checks fail in v4l2_ctrl_new() as name is NULL.
Fixes: c533435ffb ("media: vivid: add display present control")
Cc: stable@vger.kernel.org # for 5.3
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
