There is no need to hold the group lock when unregistering the notifier,
but doing so triggers a warning about a possible cyclic lock dependency.
The lock warning cover the case where a subdevice is about to be bound
to the notifier at the same time as it's unregistered. The locking for
this scenario is handled in the v4l2-async framework so it's safe to
remove the lock in the driver. This match the locking logic in the
driver for when the notifier in question is registered.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VIN driver have an internal concept of capture groups that covers
multiple instances of the driver. This is handled using the shared media
graph and a single notifier shared between all VIN instances.
This design do not work well if an individual VIN where to be unbound on
its own. The design could be improved up on to allow for this but would
require large changes in the v4l2-async framework. To avoid the
situation suppress the bind and unbind nodes in sysfs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The fwnode is retrieved using fwnode_graph_get_endpoint_by_id() without
the FWNODE_GRAPH_DEVICE_DISABLED flag set. So there is no need to
explicitly check if the fwnode is available as it always will be when
the check is performed, remove it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename V4L2 async notifier functions, replacing "notifier" with "nf" and
removing "_subdev" at the end of the function names adding subdevs as you
can only add subdevs to a notifier. Also wrap and otherwise clean up long
lines.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (imx7)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the R-Car V3U (r8a779a0) to the driver. The V3U has the
VIN modules connected to a ISP instead of directly to the R-Car CSI-2
receivers. The reason being that the ISP performs channel selection
based on CSI-2 VC/DT pairs and routes the video data to different VIN
modules. In other SoC versions this filtering is done by the VIN modules
themself.
While the media graph is very different from other SoCs the only
difference in operating the VIN modules is that the VC/DT filtering
should be skipped as that is performed by the ISP.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSI-2 link notifications are no longer the only option for the VIN
group. Change the symbol prefix to rvin_csi2_ for all CSI-2 specific
code and move the link notification code to the correct section not to
mix it with the soon to be added R-Car ISP channel selector notification
helpers.
There is no functional change and apart from the symbol prefix change
all functions are moved verbatim.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media device operations structure will be different depending on
what media graph layout is used. Instead of hard-coding the R-Car CSI-2
layout allow the operations to be passed as an argument.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
New IP versions will have different media graphs and require a different
link setup. Breakout the specific link setup to a callback that are
associated with the group.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The R-Car VIN group notifier will be extend to support a new group of
subdevices, the R-Car ISP channel selector in addition to the existing
R-Car CSI-2 receiver subdevices.
The existing DT parsing code can be reused if the port and max number of
endpoints are provided as parameters instead of being hard-coded. While
at it align the group notifier parser function names with the rest of
the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VIN group notifier code is intertwined with the media graph layout
code for R-Car CSI-2 subdevices, this makes it hard to extend the group
to also support the R-Car ISP channel selector.
Before breaking the two concepts apart and extending it move the group
code to its final location. There is no functional change and all
functions are moved verbatim.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VIN group have always been connected to CSI-2 receivers and this
have spilled over to the naming of the array storing the subdevice
information. In preparation for connecting other types of subdevices
rename the array to remotes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for adding a new media graph layout move the code reuse
of the parallel notifier setup from probe directly to the current media
graph initialization function. This is needed as there will be no
parallel interface in the new graph layout.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cleanup code for the async notifiers can be refactored to own
functions to reduce code duplication and improve readability. While at
it rename the CSI-2 initialization function _csi2_ instead of _mc_ to
match.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The error paths of rvin_mc_init() do not clean up properly, fix this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The controls for the video device are created in different code paths
depending on if the driver is using the media graph centric model (Gen3)
or the device centric model (Gen2 and earlier). This have lead to code
duplication that can be consolidated.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the return error code is in ret is being assigned but not
used. It and should be returned by the return statement and currently
just 0 is being returned. Fix this.
Addresses-Coverity: ("Unused value")
Fixes: b9ad52aafe ("media: rcar-vin: Rework parallel firmware parsing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the CSI-2 firmware parsing code to not use the soon to be
removed v4l2_async_notifier_parse_fwnode_endpoints_by_port() helper. The
change only aims to prepare for the removing of the old helper and there
are no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of removing the usage of the old helper
v4l2_async_notifier_parse_fwnode_endpoints_by_port() use the
v4l2_async_subdev instead of fwnode_handle to match subdevices.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the parallel firmware parsing code to not use the soon to be
removed v4l2_async_notifier_parse_fwnode_endpoints_by_port() helper. The
change only aims to prepare for the removing of the old helper and there
are no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of removing the usage of the old helper
v4l2_async_notifier_parse_fwnode_endpoints_by_port() do not dynamically
allocate the whole structure containing the parameters for the parallel
interface, instead only allocate the v4l2_async_subdev structure. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for suspend and resume by stopping and starting the video
pipeline while still retaining all buffers given to the driver by
user-space and internally allocated ones, this gives the application a
seamless experience.
Buffers are never returned to user-space unprocessed so user-space don't
notice when suspending. When resuming the driver restarts the capture
session using the internal scratch buffer, this happens before
user-space is unfrozen, this leads to speedy response times once the
application resumes its execution.
As the entire pipeline is stopped on suspend all subdevices in use are
also stopped, and if they enter a shutdown state when not streaming
(such as the R-Car CSI-2 driver) they too will be suspended and resumed
in sync with the VIN driver.
To be able to do keep track of which VINs should be resumed a new
internal state SUSPENDED is added to recode this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mandatory compatible value 'renesas,rcar-gen2-vin' was added to all
Gen2 DTS files in 2017, remove the redundant device specific values from
the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable YDS bit if bus_width and data_shift is set to 8 in parallel mode
for MEDIA_BUS_FMT_UYVY8_2X8 format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the SoC specific information for RZ/G2H (R8A774E1) SoC. Also add
the routing information between CSI2 and VIN (which is similar to
R-Car H3 except it lacks CSI41).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media device is not usable by userspace before all devices involved
in capture are present in the system. Move registering of the media
device to the async complete callback.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the VIN device is part of a group of VIN devices (all Gen3 boards)
there is no reason to only unregister the group notifier if the VIN that
registers the notifier is removed. The VIN that registers the notifier
is always the last VIN device to be bound, so keeping the notifier
around after any VIN is unbound creates an unbalanced state where no VIN
in the group is operational.
Fix this by unconditionally unregistering the notifier when any VIN
device is unbound. Unregistering the notifier will lead to unbound()
being called and all video devices exposed by any VIN instance to be
removed.
The lock was only needed to protect the check which VIN registers the
notifier and is no longer needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the SoC specific information for RZ/G2N(R8A774B1) SoC.
The VIN module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most but not all Gen3 hardware support outputting NV12, add a flag to
indicate which SoCs do support it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Simplify these function implementations by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to adding support for RGB pixel formats with an alpha
component add a control to allow the user to control which alpha value
should be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the SoC specific information for RZ/G2M(r8a774a1) SoC.
The VIN module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changes to v4l2-fwnode in commit [1] triggered a lockdep warning in
rcar-vin. The first attempt to solve this warning in the rcar-vin driver
was incomplete and only pushed the warning to happen at stream on time
instead of at probe time.
This change reverts the incomplete fix and properly fixes the warning by
removing the need to hold the rcar-vin specific group lock when calling
v4l2_async_notifier_parse_fwnode_endpoints_by_port(). And instead takes
it in the callback where it's really needed.
[1] commit eae2aed1ea ("media: v4l2-fwnode: Switch to
v4l2_async_notifier_add_subdev")
Fixes: 6458afc8c4 ("media: rcar-vin: remove unneeded locking in async callbacks")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a block of code in rvin_group_link_notify() that prevents
enabling a link to a VIN node if any entity in the media graph is
in use. This prevents enabling a VIN link even if there is an in-use
entity somewhere in the graph that is independent of the link's
pipeline.
For example, the code block will prevent enabling a link from
the first rcar-csi2 receiver to a VIN node even if there is an
enabled link somewhere far upstream on the second independent
rcar-csi2 receiver pipeline.
If this code block is meant to prevent modifying a link if any entity
in the graph is actively involved in streaming (because modifying
the CHSEL register fields can disrupt any/all running streams), then
the entities stream counts should be checked rather than the use counts.
(There is already such a check in __media_entity_setup_link() that verifies
the stream_count of the link's source and sink entities are both zero,
but that is insufficient, since there should be no running streams in
the entire graph).
Modify the code block to check the entity stream_count instead of the
use_count (and elaborate on the comment). VIN node links can now be
enabled even if there are other independent in-use entities that are
not streaming.
Fixes: c0cc5aef31 ("media: rcar-vin: add link notify for Gen3")
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to the RZ/G2 User's manual, RZ/G2E and R-Car E3 VIN
blocks are identical, therefore use R-Car E3 definitions to add
RZ/G2E support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The locking implemented in the async notifier callbacks are unnecessary
as the global list_lock in v4l2-async.c is held whenever one of the
callbacks are called.
The locking in itself is not harmful however it produces a LOCKDEP
warning between the global v4l2-async list_lock and the rcar-vin local
locking schema. Remove the rcar-vin locking for the async callbacks to
reduce complexity and silent the false LOCKDEP warning.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the R8A77980 SoC support to the R-Car VIN driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add R-Car E3 R8A77990 SoC to the rcar-vin supported ones.
Based on the experimental patch from Magnus Damm.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The fwnode endpoint and reference parsing functions in v4l2-fwnode.c
are modified to make use of v4l2_async_notifier_add_subdev().
As a result the notifier->subdevs array is no longer allocated or
re-allocated, and by extension the max_subdevs value is also no
longer needed.
Callers of the fwnode endpoint and reference parsing functions must now
first initialize the notifier with a call to v4l2_async_notifier_init().
This includes the function v4l2_async_register_subdev_sensor_common(),
and the intel-ipu3, omap3isp, and rcar-vin drivers.
Since the notifier->subdevs array is no longer allocated in the
fwnode endpoint and reference parsing functions, the callers of
those functions must never reference that array, since it is now
NULL. Of the drivers that make use of the fwnode/ref parsing,
only the intel-ipu3 driver references the ->subdevs[] array,
(in the notifier completion callback), so that driver has been
modified to iterate through the notifier->asd_list instead.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When adding support for parallel subdev for Gen3 it was missed that the
symbol 'i' in rvin_group_link_notify() was already declared, remove the
dupe as it's only used as a loop variable this have no functional
change. This fixes warning:
rcar-core.c:117:52: originally declared here
rcar-core.c:173:30: warning: symbol 'i' shadows an earlier one
Fixes: 1284605dc8 ("media: rcar-vin: Handle parallel subdev in link_notify")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a 'bool from_other_dev' argument: set to true if the two
handlers refer to different devices (e.g. it is true when
inheriting controls from a subdev into a main v4l2 bridge
driver).
This will be used later when implementing support for the
request API since we need to skip such controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kconfig and Makefile doesn't have license line, thus,
these are GPL-2.0 as default.
All ohter files are GPL-2.0+ as original license.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handle parallel subdevices in link_notify callback. If the notified link
involves a parallel subdevice, do not change routing of the VIN-CSI-2
devices and mark the VIN instance as using a parallel input. If the
CSI-2 link setup succeeds instead, mark the VIN instance as using CSI-2.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
