This patch adds a new behavior to report touch major resolution
based on information provided by firmware.
In initial process, driver acquires touch information from touch ic.
It contains one byte about the resolution value of ABS_MT_TOUCH_MAJOR.
Touch driver will report touch major resolution by this information.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/1598581195-9874-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On an AMD chromebook, where the same I2C bus is shared by both Raydium
touchscreen and a trackpad device, it is observed that interleaving of
I2C messages when `raydium_i2c_read_message()` is called leads to the
Raydium touch IC reporting incorrect information. This is the sequence
that was observed to result in the above issue:
* I2C write to Raydium device for RM_CMD_BANK_SWITCH
* I2C write to trackpad device
* I2C read from trackpad device
* I2C write to Raydium device for setting address
* I2C read from Raydium device >>>> This provides incorrect
information
This change adds a new helper function `raydium_i2c_xfer()` that
performs I2C transactions to the Raydium device. It uses the register
address to decide if RM_CMD_BANK_SWITCH header needs to be sent to the
device (i.e. if register address is greater than 255, then bank switch
header is sent before the rest of the transaction). Additionally, it
ensures that all the I2C operations performed as part of
`raydium_i2c_xfer()` are done as a single i2c_transfer. This
guarantees that no other transactions are initiated to any other
device on the same bus in between. Additionally,
`raydium_i2c_{send|read}*` functions are refactored to use this new
helper function.
Verified with the patch across multiple reboots (>100) that the
information reported by the Raydium touchscreen device during probe
is correct.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20200821024006.3399663-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad controller driver supporting newer ICs
with enhanced precision reports and a new firmware update process
- an update to EXC3000 touch controller supporting additional parts
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: exc3000 - add support to query model and fw_version
Input: exc3000 - add reset gpio support
Input: exc3000 - add EXC80H60 and EXC80H84 support
dt-bindings: touchscreen: Convert EETI EXC3000 touchscreen to json-schema
Input: sentelic - fix error return when fsp_reg_write fails
Input: alps - remove redundant assignment to variable ret
Input: ims-pcu - return error code rather than -ENOMEM
Input: elan_i2c - add ic type 0x15
Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary
Input: uinput - fix typo in function name documentation
Input: ati_remote2 - add missing newlines when printing module parameters
Input: psmouse - add a newline when printing 'proto' by sysfs
Input: synaptics-rmi4 - drop a duplicated word
Input: elan_i2c - add support for high resolution reports
Input: elan_i2c - do not constantly re-query pattern ID
Input: elan_i2c - add firmware update info for ICs 0x11, 0x13, 0x14
Input: elan_i2c - handle firmware updated on newer ICs
Input: elan_i2c - add support for different firmware page sizes
Input: elan_i2c - fix detecting IAP version on older controllers
Input: elan_i2c - handle devices with patterns above 1
...
Expose model and fw_version via sysfs. Also query the model
in probe to make sure, that the I2C communication with the
device works before successfully probing the driver.
This is a bit complicated, since EETI devices do not have
a sync interface. Sending the commands and directly reading
does not work. Sending the command and waiting for some time
is also not an option, since there might be touch events in
the mean time.
Last but not least we do not cache the results, since this
interface can be used to check the I2C communication is still
working as expected.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20200805160520.456570-5-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add basic support for an optional reset gpio.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-4-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for EXC80H60 and EXCH84 controllers, which
use a different event type id and have two extra bits for the
resolution (so the maximum is 16K instead of 4K).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-3-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv2rA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngIgCfZOVj022X+paV81NwvO/TroMDA7oAn1C4XCmY
Fxz55oHIyk9lbQxsDhID
=ujqG
-----END PGP SIGNATURE-----
Merge tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems"
* tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (428 commits)
staging: most: fix up movement of USB driver
staging: rts5208: clear alignment style issues
staging: r8188eu: replace rtw_netdev_priv define with inline function
staging: netlogic: clear alignment style issues
staging: android: ashmem: Fix lockdep warning for write operation
drivers: most: add USB adapter driver
staging: most: Use %pM format specifier for MAC addresses
staging: ks7010: Use %pM format specifier for MAC addresses
staging: qlge: qlge_dbg: removed comment repition
staging: wfx: Use flex_array_size() helper in memcpy()
staging: rtl8723bs: Align macro definitions
staging: rtl8723bs: Clean up function declations
staging: rtl8723bs: Fix coding style errors
drivers: staging: audio: Fix the missing header file for helper file
staging: greybus: audio: Enable GB codec, audio module compilation.
staging: greybus: audio: Add helper APIs for dynamic audio modules
staging: greybus: audio: Resolve compilation error in topology parser
staging: greybus: audio: Resolve compilation errors for GB codec module
staging: greybus: audio: Maintain jack list within GB Audio module
staging: greybus: audio: Update snd_jack FW usage as per new APIs
...
The workaround of reading all messages until an invalid is received is a
way of forcing the CHG line high, which means that when using
edge-triggered interrupts the interrupt can be acquired.
With level-triggered interrupts the workaround is unnecessary.
Also, most recent maXTouch chips have a feature called RETRIGEN which, when
enabled, reasserts the interrupt line every cycle if there are messages
waiting. This also makes the workaround unnecessary.
Note: the RETRIGEN feature is only in some firmware versions/chips, it's
not valid simply to enable the bit.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
(cherry picked from ndyer/linux/for-upstream commit 1ae4e8281e491b22442cd5acdfca1862555f8ecb)
[gdavis: Fix conflicts due to v4.6-rc7 commit eb43335c40 ("Input:
atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_reset").]
Signed-off-by: George G. Davis <george_davis@mentor.com>
[jiada: reset use_retrigen_workaround at beginning of mxt_check_retrigen()
call mxt_check_retrigen() after mxt_acquire_irq() in mxt_initialize()
replace white-spaces with tab for MXT_COMMS_RETRIGEN
Changed to check if IRQ is level type]
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200727151637.23810-1-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into staging-next
We need the staging fixes in here, and it resolves a merge issue with an
iio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
This reverts commit 0617067163 - it turns
out that the resolution of 1 unit per mm was not correct for a number of
touch screens, causing touch sizes to be reported as way too large.
See https://crbug.com/1085648
Reported-by: Harry Cutts <hcutts@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull input updates from Dmitry Torokhov:
- a new driver for the Azoteq IQS269A capacitive touch controller
- a new driver for the Cypress CY8CTMA140 touchscreen
- updates to Elan and ft5x06 touchscreen drivers
- assorted driver fixes
- msm-vibrator has been removed as we have a more generic solution
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: adi - work around module name confict
Input: iqs269a - add missing I2C dependency
Input: elants - refactor elants_i2c_execute_command()
Input: elants - override touchscreen info with DT properties
Input: elants - remove unused axes
Input: add support for Azoteq IQS269A
dt-bindings: input: Add bindings for Azoteq IQS269A
Input: imx_sc_key - use devm_add_action_or_reset() to handle all cleanups
Input: remove msm-vibrator driver
dt-bindings: Input: remove msm-vibrator
Input: elants_i2c - provide an attribute to show calibration count
Input: introduce input_mt_report_slot_inactive()
dt-bindings: input: touchscreen: elants_i2c: convert to YAML
Input: add driver for the Cypress CY8CTMA140 touchscreen
dt-bindings: touchscreen: Add CY8CTMA140 bindings
Input: edt-ft5x06 - prefer asynchronous probe
Input: edt-ft5x06 - improve power management operations
Input: edt-ft5x06 - move parameter restore into helper
Input: edt-ft5x06 - fix get_default register write access
Input: atkbd - receive and use physcode->keycode mapping from FW
...
Allow overriding of information from hardware and support additional
common DT properties like axis inversion. This is required for eg.
Nexus 7 and TF300T where the programmed values in firmware differ
from reality.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[moved "prop" before DMA buffer]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/49ea996878264f7c8bde25204e4ddf4b1e85ae71.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Driver only ever reports MT events and input_mt_init_slots() sets up
emulated axes already. Clear the capabilities not generated directly
and move MT axes setup, so they are visible by input_mt_init_slots().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/d5eee8cd305adb144a11264d70da94f7b6570366.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is an non-touch case by non-calibration after update firmware.
Elan could know calibrate or not by calibration count.
The value of '0xffff' means we didn't calibrate after update firmware.
If calibrate success, it will plus one and change to '0x0000'.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/1588754932-5902-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_report_slot_state() ignores "tool" argument when the slot is
closed, which has caused a bit of confusion. Let's introduce
input_mt_report_slot_inactive() to report inactive slot state.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200508055656.96389-2-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge tag 'v5.6' into next
Sync up with mainline to get device tree and other changes.
This adds a new driver for the Cypress CY8CTMA140 touchscreen.
This driver is inspired by out-of-tree code for the Samsung
GT-S7710 mobile phone.
I have tried to compare the structure and behaviour of this
touchscreen to the existing CYTTSP and CYTTSP4 generics and
it seems pretty different. It is also different in character
from the cy8ctmg110_ts.c. It appears to rather be vaguely
related to the Melfas MMS114 driver, yet distinctly
different.
Dmitry Torokhov rewrote the key scanning code during the
submission process so the driver is a joint work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200506123435.187432-2-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Probing the device takes a while, because we sleep for 300 ms after a
reset; allow asynchronous probing so this can happen in the background
while other devices are being probed.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-5-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to restore the parameters if we switch between the
factory/work mode and during the resume process if we switched off the
power-supply. Therefore refactor edt_ft5x06_work_mode() and move the
"restore the parameters" into a helper routine so we can reuse it later.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-3-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit b6eba86030 ("Input: edt-ft5x06 - add offset support for
ev-ft5726") offset-x and offset-y is supported. Devices using those
offset parameters don't support the offset parameter so we need to add
the NO_REGISTER check for edt_ft5x06_ts_get_defaults().
Fixes: b6eba86030 ("Input: edt-ft5x06 - add offset support for ev-ft5726")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-2-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS345L is another first generation touch screen from Melfas,
which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization.
Apparently MMS345L does not have the MMS152_COMPAT_GROUP register
that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as
an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading
from the MMS152_COMPAT_GROUP register. This might also help in case
there is some other device-specific quirk in the future.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200423102431.2715-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on available information this uses the singletouch irtouch
protocol. This is tested and confirmed to be fully functional on
the BonXeon TP hardware I have.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20200413184217.55700-1-james.hilliard1@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS345L is another first generation touch screen from Melfas,
which uses the same registers as MMS152.
However, using I2C_M_NOSTART for it causes errors when reading:
i2c i2c-0: sendbytes: NAK bailout.
mms114 0-0048: __mms114_read_reg: i2c transfer failed (-5)
The driver works fine as soon as I2C_M_NOSTART is removed.
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200405170904.61512-1-stephan@gerhold.net
[dtor: removed separate mms345l handling, made everyone use standard
transfer mode, propagated the 10bit addressing flag to the read part of the
transfer as well.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Elan uses the least significant bit of byte 33 to signal the type of
contact (finger versus palm). The default value is 1 for all firmwares,
which is reported as MT_TOOL_FINGER. If firmware supports palm detection,
the bit will change to 0 and the driver will report such contact as
MT_TOOL_PALM.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://lore.kernel.org/r/1585551756-29066-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"An update to the Goodix touchscreen driver to enable it work properly
on various Bay Trail and Cherry Trail devices, and a few other
assorted changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: update SPDX tag for input-event-codes.h
Input: i8042 - add Acer Aspire 5738z to nomux list
Input: goodix - fix compilation when ACPI support is disabled
dt-bindings: touchscreen: Convert edt-ft5x06 to json-schema
Input: of_touchscreen - explicitly choose axis
Input: goodix - support gt9147 touchpanel
dt-bindings: touchscreen: goodix: support of gt9147
Input: goodix - add support for Goodix GT917S
Input: goodix - use string-based chip ID
dt-bindings: input: touchscreen: add compatible string for Goodix GT917S
Input: goodix - add support for more then one touch-key
Input: goodix - fix spurious key release events
Input: goodix - try to reset the controller if the i2c-test fails
Input: goodix - restore config on resume if necessary
Input: goodix - make goodix_send_cfg() take a raw buffer as argument
Input: goodix - add minimum firmware size check
Input: goodix - save a copy of the config from goodix_read_config()
Input: goodix - move defines to above struct goodix_ts_data declaration
Input: goodix - add support for controlling the IRQ pin through ACPI methods
Input: goodix - add support for getting IRQ + reset GPIOs on Bay Trail devices
...
acpi_evaluate_object() and acpi_execute_simple_method() are not part of
the group of ACPI related functions which get stubbed by
include/linux/acpi.h when ACPI support is disabled, so the
IRQ_PIN_ACCESS_ACPI_METHOD handling code must be stubbed out.
For consistency use the same #if condition as which is used to replace
goodix_add_acpi_gpio_mappings with a stub.
Fixes: c5fca48532 ("Input: goodix - add support for controlling the IRQ pin through ACPI methods")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200401014529.GL75430@dtor-ws
[dtor: stubbed out the ACPI method accessors]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and use
of new apis, a libfs fix, a debugfs api change, and some driver core
deferred probe rework.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHLIg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yle2ACgjJJzRJl9Ckae3ms+9CS4OSFFZPsAoKSrXmFc
Z7goYQdZo1zz8c0RYDrJ
=Y91m
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and
use of new apis, a libfs fix, a debugfs api change, and some driver
core deferred probe rework.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (44 commits)
Revert "driver core: Set fw_devlink to "permissive" behavior by default"
driver core: Set fw_devlink to "permissive" behavior by default
driver core: Replace open-coded list_last_entry()
driver core: Read atomic counter once in driver_probe_done()
libfs: fix infoleak in simple_attr_read()
driver core: Add device links from fwnode only for the primary device
platform/x86: touchscreen_dmi: Add info for the Chuwi Vi8 Plus tablet
platform/x86: touchscreen_dmi: Add EFI embedded firmware info support
Input: icn8505 - Switch to firmware_request_platform for retreiving the fw
Input: silead - Switch to firmware_request_platform for retreiving the fw
selftests: firmware: Add firmware_request_platform tests
test_firmware: add support for firmware_request_platform
firmware: Add new platform fallback mechanism and firmware_request_platform()
Revert "drivers: base: power: wakeup.c: Use built-in RCU list checking"
drivers: base: power: wakeup.c: Use built-in RCU list checking
component: allow missing unbind callback
debugfs: remove return value of debugfs_create_file_size()
debugfs: Check module state before warning in {full/open}_proxy_open()
firmware: fix a double abort case with fw_load_sysfs_fallback
arch_topology: Fix putting invalid cpu clk
...
The 'axis + 1' calculation is implicit and potentially error prone.
Moreover, few lines before the axis is set explicitly for both X and Y.
Do the same when retrieving different properties for X and Y.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200303180917.12563-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for it by adding compatible and supported chip data
(default settings used).
The chip data on GT9147 is similar to GT912, like
- config data register has 0x8047 address
- config data register max len is 240
- config data checksum has 8-bit
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/1583144308-3781-3-git-send-email-yannick.fertre@st.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix GT917S is a touchscreen chip from Goodix that is in the GT1x
family.
Add its support by assigning the gt1x config to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-4-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For Goodix GT917S chip, the chip ID string is "917S", which contains not
only numbers now.
Use string-based chip ID in the driver to support this chip and further
chips with alphanumber ID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-3-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
GpioIo (Shared, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0019
}
})
Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}
There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().
This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.
Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.
This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.
Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.
And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.
So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.
This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.
This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately sofar we have been unable to get permission to redistribute
icn8505 touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with an icn8505 touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the icn8505 driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-9-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately sofar we have been unable to get permission to redistribute
Silead touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with a Silead touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the silead driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-8-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions are supposed to return negative error codes but instead
it returns true on failure and false on success. The error codes are
eventually propagated back to user space.
Fixes: 48a2b78348 ("Input: add Raydium I2C touchscreen driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200303101306.4potflz7na2nn3od@kili.mountain
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch supports reporting resolution for ABS_MT_TOUCH_MAJOR event.
This information is needed in showing pressure/width radius.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/1582766000-23023-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Cube I15-TC don't match the default display,
with 0,0 touches being reported when touching at the top-right of
the screen.
Add a quirk to invert the x coordinate.
Reported-and-tested-by: Arkadiy <arkan49@yandex.ru>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the Ilitek ili2120 touchscreen found in the
Fairphone 2 smartphone.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20200209151904.661210-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The is_visible function expects the permissions associated with an
attribute of the sysfs group or 0 if an attribute is not visible.
Change the code to return the attribute permissions when the attribute
should be visible which resolves the warning:
Attribute calibrate: Invalid permissions 01
Fixes: cc12ba1872 ("Input: ili210x - optionally show calibrate sysfs attribute")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20200209145628.649409-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191210141103.15910-1-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl4SYegeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4m4H+QGCUN8SXN+2B+0/
BfzOf7PFoKzAx3NwDbJQIZqhSl+Zfa4n3VGPEF8sXsvoQgdYvuJnS/5JiAZ9iRIH
HAfFzegzQ3mCl8Du+SqCvQKs2Jt4OMCX62KGRebRBhpoKfZdwmN7n7pn9lWO771K
9rxTpeItXhmK46jOFRbi5oyQfmkfSfyUN1b9CB53FXFS+ZDkDNA7QQiIYnKOD7SZ
RrL7czhZ580QOC61qOlnz1GIhRzvU5SXg4OtuI3YfoOJRY5FKC3YtOgLReT0vPs+
vEhAyP93upVXIhqm10WHNjd4t4a45Vy5ff64uFsQ9QV4nnqsC2C70YwWbVDdtz/W
Lm0mvE8=
=NECs
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rc5' into next
Sync up with mainline to get SPI "delay" API changes.
We do not have to handle the wake-irq within the driver because the pm
core can handle this for us. The only use case for the suspend/resume
callbacks was to handle the wake-irq so we can remove the callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since day one the touch controller acts as wakeup-source. This seems to
be wrong since the device supports deep-sleep mechanism [1] which
requires a reset to leave it. Also some designs won't use the
touchscreen as wakeup-source.
According discussion [2] we decided to break backward compatibility and
go the common way by using the 'wakeup-source' device-property.
[1] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x26.pdf
[2] https://patchwork.kernel.org/patch/11149037/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It seems that the include order is historical increased and no one takes
care of it. Fix this to align it with the common rule to be in a
alphabetical order.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid flashing incompatible firmware onto a device we should check
whether "Remark ID" in firmware matches with the one in the controller.
This function is supported by Elan's latest version of boot code, so the
driver decides whether to perform the check based on the boot code version.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/00a901d5af3c$193e9cd0$4bbbd670$@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306373-29581-1-git-send-email-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Only show the 'calibrate' sysfs attribute on chip flavours
which support calibration by writing to a calibration register.
Do this by adding a flag to the chip operations structure.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-2-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Optionally allow the touch screen resolution to be set by adding
it to the chip operations structure. If it is omitted (left zero),
the resolution defaults to 64K. Which is the previously hard-coded
value.
Set the ili2117 resolution to 2048, as indicated in its datasheet.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver's method to retrieve the firmware version on ili2117/
ili2118 chip flavours is incorrect. The firmware version register
address and layout are wrong.
The firmware version is not actually used anywhere inside or
outside this driver. There is a dev_dbg() print, but that is
only visible when the developer explicitly compiles in debug
support.
Don't make the code more complicated to preserve a feature that
no-one is using. Remove all code associated with chip firmware
version.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112164429.11225-1-TheSven73@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
device_get_match_data is available now, so we can replace the call
to of_device_get_match_data and remove the FIXME comment.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20191007203343.101466-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When I2C client is instantiated with I2C_CLIENT_WAKE flag (either via
"wakeup-source" device property, or via board info flag), it will mark the
main IRQ line as wakeup IRQ, which will ensure that it will be enabled for
wakeup when system transitions to suspend state. Since our suspend/resume
handlers were only managing IRQ wakeup state, they are no longer needed,
and can be removed.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I2C devices that are supposed to be wakeup sources should be instantiated
with I2C_CLIENT_WAKE flag (which can be either set by in board info, or
retrieved from "wakeup-source" property); individual drivers should not be
marking devices as wakeup sources unconditionally.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing if/else if/else on the chip's model number let's define
chip operations structure and use it to perform indirect calls. With number
of protocols supported by the driver growing, this makes it better
maintainable.
This change includes fixes to checks whether the driver should continue
polling the controller by Sven Van Asbroeck <thesven73@gmail.com>.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using devm_input_allocate_device() that set's up the parent for
us, no need to do it ourselves.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() may fail and we need to handle such failures.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to using threaded IRQ so that we do not need to
manage the interrupt and work separately, and we do not acknowledge
interrupt until we finished handling it completely.
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Tested-by: Marek Vasut <marex@denx.de> # ILI2117
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI2117 touch controller. This controller is similar
to the ILI210x and ILI251x, except for the following differences:
- Reading out of touch data must happen at most 300 mS after the
interrupt line was asserted. No command must be sent, the data
are returned upon pure I2C read of 43 bytes long.
- Supports 10 simultaneous touch inputs.
- Touch data format is slightly different.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org> # for DT binding
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts tsc6507x-ts driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Link: https://lore.kernel.org/r/20191017204217.106453-5-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts ts4800-ts driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Link: https://lore.kernel.org/r/20191017204217.106453-4-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts sur40 driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Link: https://lore.kernel.org/r/20191017204217.106453-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have added polled mode to the normal input devices with the intent of
retiring input_polled_dev. This converts raspberrypi-ts driver to use the
polling mode of standard input devices and removes dependency on
INPUT_POLLDEV.
Link: https://lore.kernel.org/r/20191017204217.106453-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the support for enabling optional regulator that may be used as VCC
source.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Rob Herring <robh@kernel.org> # bindings
Link: https://lore.kernel.org/r/20191029005806.3577376-2-megous@megous.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the driver to the slotted variant of multitouch protocol (MT-B)
with in-kernel tracking of the contacts.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The receiving buffer is allocated separately from the main driver
data structure, and is naturally DMA-safe, so mark it as such when
building I2C transfer message.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The finger structure size is quite small and allocating it together with
the main driver structure will not increase likelyhood of allocation
failing, but reduces number of objects needing to be tracked by the
allocator and devm.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be putting the chip into reset while interrupts are enabled
and ISR may be running. Fix this by installing a custom devm action and
powering off the device/resetting GPIO line from there. This ensures proper
ordering.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When I2C client is created with I2C_CLIENT_WAKE flag (which happens
either because we have "wakeup-source" device property or the flag
was passed in when creating an I2C client manually), I2C core will
take care of configuring interrupt as wakeup source on suspend.
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not unconditionally configure the touchscreen as wakeup source but
rather rely on I2C core to do that when requested (either via
"wakeup-source" device property, or when creating a client with
I2C_CLIENT_WAKE flag).
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Avoid complex 2-variable loop when parsing touchscreen data to make the
code clearer.
Acked-by: Martin Kepplinger <martink@posteo.de>
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no gpio functions used in the driver that is exported
by the gpio.h header, so remove this unneeded header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20191026185958.24158-3-festevam@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no gpio functions used in the driver that is exported
by the gpio.h header, so remove this unneeded header.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20191026185958.24158-2-festevam@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen device is a GPIO consumer, not a GPIO controller,
so there is no need to include <linux/gpio.h>.
Remove the unneeded header file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20191026185958.24158-1-festevam@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl210Z8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGv+kIAKRpO7EuDokQL4qp
hxEEaCMJA1T055EMlNU6FVAq/ZbmapzreUyNYiRMpPWKGTWNMkhIcZQfysYeGZz5
y/KRxAiVxlcB+3v3yRmoZd/XoQmhgvJmqD4zhaGI2Utonow4f/SGSEFFZqqs9WND
4HJROjZHgQ4JBxg9Z+QMo0FxbV/DCZpEOUq51N9WJywyyDRb18zotE83stpU+pE2
fjqT7mk0NLrnYXuDRAbFC1Aau9ed4H6LlwLmxaqxq/Pt5Rz7wIKwKL9HIT4Dm/0a
qpani6phhHWL7MwUpa2wkEonFCD03rJFl3DUVJo64Ijh4up5D/jyXQ+GKV2P4WKJ
275Rb5Q=
=WiZZ
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rc5' into next
Sync up with mainline.
Pull input fix from Dmitry Torokhov:
"A fix for st1232 driver to properly report coordinates for 2nd and
subsequent fingers when more than one is on the surface"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: st1232 - fix reporting multitouch coordinates
Pull input fixes from Dmitry Torokhov:
"The main change is that we are reverting blanket enablement of SMBus
mode for devices with Elan touchpads that report BIOS release date as
2018+ because there are older boxes with updated BIOSes that still do
not work well in SMbus mode.
We will have to establish whitelist for SMBus mode it looks like"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: elantech - enable SMBus on new (2018+) systems"
Input: synaptics-rmi4 - avoid processing unknown IRQs
Input: soc_button_array - partial revert of support for newer surface devices
Input: goodix - add support for 9-bytes reports
Input: da9063 - fix capability and drop KEY_SLEEP
Previous change moved platform data definition into the driver, making it
unusable for users. Given that we want to move away from custom platform
data structures, and always use device properties (DT, ACPI or static) to
configure devices, let's complete the removal.
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case of defer probe we should not print an error message.
This also aligns with how defer probe is handled in the other GPIOs
used by this driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pixcir datasheet lists the registers addresses in decimal and
so are PIXCIR_REG_POWER_MODE and PIXCIR_REG_INT_MODE defined in decimal.
Change the error messages to print the register addresses in decimal
instead of hexadecimal for better readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Keep the header files in alphabetical order to keep it
more organized.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All the defined symbols from linux/platform_data/pixcir_i2c_ts.h
are only used by the pixcir_i2c_ts driver, so move all the definitions
locally and get rid of the pixcir_i2c_ts.h file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen device is a GPIO consumer, not a GPIO controller,
so there is no need to include <linux/gpio.h>.
Remove the unneeded header file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of Goodix touchscreen firmwares use 9-bytes finger
report format instead of common 8-bytes format.
This report format may be present as:
struct goodix_contact_data {
uint8_t unknown1;
uint8_t track_id;
uint8_t unknown2;
uint16_t x;
uint16_t y;
uint16_t w;
}__attribute__((packed));
Add support for such format and use it for Lenovo Yoga Book notebook
(which uses a Goodix touchpad as a touch keyboard).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- input core allows hardware drivers to specify a [more precise]
timestamp (normally taken in top half) to better track velocity of
contacts
- input_dev instances now support "polling" mode so that drivers could
use the same object for polled and interrupt-driven operation. The
plan is to convert existing drivers and retire input_polled_dev API
- a new driver for the FlySky FS-iA6B RC receiver
- a refresh of BU21013 touchpad driver
- w90x900 keyboard and touchpad drivers are removed as the platform is
gone
- assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: sidewinder - make array seq static const, makes object smaller
Input: reset device timestamp on sync
Input: bu21013_ts - switch to using standard touchscreen properties
Input: bu21013_ts - switch to using MT-B (slotted) protocol
Input: bu21013_ts - fix suspend when wake source
Input: bu21013_ts - use interrupt from I2C client
Input: bu21013_ts - remove support for platform data
Input: bu21013_ts - convert to using managed resources
Input: bu21013_ts - remove useless comments
Input: bu21013_ts - annotate supend/resume methods as __maybe_unused
Input: bu21013_ts - rename some variables
Input: bu21013_ts - convert to use GPIO descriptors
ARM: ux500: improve BU21013 touchpad bindings
Input: i8042 - enable wakeup on a stable struct device
Input: soc_button_array - use platform_device_register_resndata()
Input: psmouse - drop all unneeded functions from mouse headers
Input: add support for polling to input devices
Input: wacom_w8001 - allocate additional space for 'phys'
Input: cros_ec_keyb - add back missing mask for event_type
Input: remove dev_err() usage after platform_get_irq()
...
This switches the driver over to the standard touchscreen properties for
coordinate transformation, while keeping old bindings working as well.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MT-B protocol is more efficient and everyone expects it. We use in-kernel
tracking to identify contacts.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the touchscreen is configured as wakeup source we should not be cutting
off power to it.
Also, now that the driver relies on I2C client to supply IRQ, we do not
need to explicitly enable and disable IRQ for wakeup: if device is created
as wakeup source, I2C core will mark interrupt as wakeup one.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of trying to map INT GPIO to interrupt, let's use one supplied by
I2C client. If there is none - bail. This will also allow us to treat INT
GPIO as optional, as per the binding.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are no current users of the platform data in the tree, and
any new users should either use device tree, or static device
properties to describe the device.
This change drop the platform data definition and handling and moves the
driver over to generic device properties API. We also drop support for the
external clock. If it is needed we will have to extend the bindings to
supply the clock reference and handle it properly in the driver.
Also, wakeup setting should be coming from I2C client.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The comments for individual functions in the driver do not provide any
additional information beyond what function names indicate.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead if #ifdef-ing out suspend and resume methods, let's mark
them as __maybe_unused to get better compile time coverage.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"bu21013_data" and "struct bu21013_ts_data" are a tad long, let's call them
"ts" and "struct bu21013_ts".
Also rename retval to error in bu21013_init_chip() and adjust formatting;
i2c_smbus_write_byte_data() returns negative on error and 0 on success, so
we simply test if whether erro is 0 or not.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver can use GPIO descriptors rather than GPIO numbers
without any problems, convert it. Name the field variables after
the actual pins on the chip rather than the "reset" and "touch"
names from the devicetree bindings that are vaguely inaccurate.
No in-tree users pass GPIO numbers in platform data so drop
this. Descriptor tables can be used to get these GPIOs from a board
file if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GCC warns that the output of our call to 'snprintf' in 'w8001_connect'
may be truncated since both 'serio->phys' and 'w8001->phys' are 32 bytes
in length. Increase the amount of space allocated for the latter to
compensate.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl1QegseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGavMH/RBaR39ct3XXpPzC
yxmKJn/n692NXFKusfsfasitGHMdFom6HaCcKx4PpzX1QHnR34LJtMd1QvwM8cHz
FtbC68HyZBB91JOUzC38GbRufvVUsSeXg8YeBiF6BOoOP06OcOG+DKoPcKBOMXsR
MtJmgxEyedLT7ozEPTpowVBWulELJxkbe1MCc93xDXdOqT+aMuxZBASMJIgrufS7
uJTsJ/afHz6F29Mj6Q9lfIJJSHqSfMK/rPGP54xRdBgMWmAmNjA2aExyCK8PE/Yb
TChsrDjDz38ePuVaWfjtwFNWlWcq0Do8vJdPuAxZDdfaJlQDXQHCWXsJjrWD6oNy
ZhCq0zE=
=HcEO
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rc4' into next
Sync up with mainline to bring in device_property_count_u32 andother
newer APIs.
Pull input updates from Dmitry Torokhov:
- newer systems with Elan touchpads will be switched over to SMBus
- HP Spectre X360 will be using SMbus/RMI4
- checks for invalid USB descriptors in kbtab and iforce
- build fixes for applespi driver (misconfigs)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add sanity checks
Input: applespi - use struct_size() helper
Input: kbtab - sanity check for endpoint type
Input: usbtouchscreen - initialize PM mutex before using it
Input: applespi - add dependency on LEDS_CLASS
Input: synaptics - enable RMI mode for HP Spectre X360
Input: elantech - annotate fall-through case in elantech_use_host_notify()
Input: elantech - enable SMBus on new (2018+) systems
Input: applespi - fix trivial typo in struct description
Input: applespi - select CRC16 module
Input: applespi - fix warnings detected by sparse
The ARM w90x900 platform is getting removed, so this driver is obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A few vendor specific bindings are now covered by common bindings.
Let the driver parse the common bindings to make use of common
inverting and swapping mechnism. Aslo make use of
touchscreen_report_pos() to ensure the correct inverting-swapping
order.
The vendor specific properties are used as default (backward
compatibility) and gets overwritten by common bindings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_platform_ioremap_resource() internally have platform_get_resource()
and devm_ioremap_resource() in it. So instead of calling them separately
use devm_platform_ioremap_resource() directly.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver set the colorspace to SRGB, but that makes no sense for
a touchscreen. Use RAW instead. This also ensures consistency with the
v4l_pix_format_touch() call that's used in v4l2-ioctl.c.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Florian Echtler <floe@butterbrot.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pull more input updates from Dmitry Torokhov:
- Apple SPI keyboard and trackpad driver for newer Macs
- ALPS driver will ignore trackpoint-only devices to give the
trackpoint driver a chance to handle them properly
- another Lenovo is switched over to SMbus from PS/2
- assorted driver fixups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - fix a mismatch between a condition check and its comment
Input: psmouse - fix build error of multiple definition
Input: applespi - remove set but not used variables 'sts'
Input: add Apple SPI keyboard and trackpad driver
Input: alps - don't handle ALPS cs19 trackpoint-only device
Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
Input: adp5589 - initialize GPIO controller parent device
Input: iforce - remove empty multiline comments
Input: synaptics - fix misuse of strlcpy
Input: auo-pixcir-ts - switch to using devm_add_action_or_reset()
Input: gtco - bounds check collection indent level
Input: mtk-pmic-keys - add of_node_put() before return
Input: sun4i-lradc-keys - add of_node_put() before return
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0idTweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZesIAJDKicw2Voyx8K8m
3pXSK+71RuO/d3Y9M51mdfTMKRP4PHR9/4wVZ9wHPwC4dV6wxgsmIYCF69a1Wety
LD1MpDCP1DK5wVfPNKVX2xmj7ua6iutPtSsJHzdzM2TlscgsrFKjmUccqJ5JLwL5
c34nqwXWnzzRyI5Ga9cQSlwzAXq0vDHXyML3AnCosSsLX0lKFrHlK1zttdOPNkfj
dXRN62g3q+9kVQozzhDXb8atZZ7IkBk8Q0lujpNXW83Ci1VjaVNv3SB8GZTXIlLj
U15VdyuwfJDfpBgFBN6/unzVaAB6FFrEKy0jT1aeTyKarMKDKgOnJjn10aKjDNno
/bXsKKc=
=TVqV
-----END PGP SIGNATURE-----
Merge tag 'v5.2' into next
Sync up with mainline to resolve conflicts in iforce driver.
Converts ARM the text files to ReST, preparing them to be an
architecture book.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by Corentin Labbe <clabbe.montjoie@gmail.com> # For sun4i-ss
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad SMBus driver to fetch device parameters
(size, resolution) while it is still in PS/2 mode, before switching
over to SMBus, as in that mode some devices return garbage dimensions
- update to iforce joystick driver
- miscellaneous driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (48 commits)
Input: gpio_keys_polled - allow specifying name of input device
Input: edt-ft5x06 - simplify event reporting code
Input: max77650-onkey - add MODULE_ALIAS()
Input: atmel_mxt_ts - fix leak in mxt_update_cfg()
Input: synaptics - enable SMBUS on T480 thinkpad trackpad
Input: atmel_mxt_ts - fix -Wunused-const-variable
Input: joydev - extend absolute mouse detection
HID: quirks: Refactor ELAN 400 and 401 handling
Input: elan_i2c - export the device id whitelist
Input: edt-ft5x06 - use get_unaligned_be16()
Input: iforce - add the Saitek R440 Force Wheel
Input: iforce - use unaligned accessors, where appropriate
Input: iforce - drop couple of temps from transport code
Input: iforce - drop bus type from iforce structure
Input: iforce - use DMA-safe buffores for USB transfers
Input: iforce - allow callers supply data buffer when fetching device IDs
Input: iforce - only call iforce_process_packet() if initialized
Input: iforce - signal command completion from transport code
Input: iforce - do not combine arguments for iforce_process_packet()
Input: iforce - factor out hat handling when parsing packets
...
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=ABgl
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
Now that input_mt_report_slot_state() returns true if slot is active we no
longer need a temporary for the slot state.
Tested-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix leak (whose magnitude is the configuration file size) when the CRCs
match in mxt_update_cfg().
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Clang produces the following warning
drivers/input/touchscreen/atmel_mxt_ts.c:259:42: warning: unused
variable 'mxt_video_fops' [-Wunused-const-variable]
static const struct v4l2_file_operations mxt_video_fops = {
Since mxt_video_fops is only used inside an ifdef. It should
be moved inside the ifdef.
Link: https://github.com/ClangBuiltLinux/linux/issues/527
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing conversion by hand, let's use the proper accessors.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Pull input updates from Dmitry Torokhov:
"Just a few small fixups and switching a couple of Thinkpads to SMBus
for touchpads as PS/2 emulation is not working well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - enable SMBus on ThinkPad E480 and E580
Input: imx_keypad - make sure keyboard can always wake up system
Input: iqs5xx - get axis info before calling input_mt_init_slots()
Input: uinput - add compat ioctl number translation for UI_*_FF_UPLOAD
Input: silead - add MSSL0017 to acpi_device_id
Input: elantech - enable middle button support on 2 ThinkPads
Input: elan_i2c - increment wakeup count if wake source
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foudation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081203.770334822@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.720704315@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
But this only really works if all drivers use this, so convert
this touchscreen driver accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Florian Echtler <floe@butterbrot.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Calling input_mt_init_slots() copies ABS_MT_POSITION_X to ABS_X and
so on, but doing so before calling touchscreen_parse_properties()
leaves ABS_X min = max = 0 which may prompt an X server to ignore
the device.
To solve this problem, wait to call input_mt_init_slots() until all
absolute axis information has been resolved (whether that's through
device tree via touchscreen_parse_properties() or from reading from
the device directly).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license gplv2 as published by the fsf
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.797597276@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 51 franklin street
fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 94 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141334.043630402@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 44 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170025.980374610@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this file is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this library if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.475087903@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see the file copying or write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071859.003492977@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version of 2 of the license or
at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.207758043@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the term of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170856.822819340@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling i2c_set_clientdata() is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On Chuwi Hi10 Plus, the Silead device id is MSSL0017.
Signed-off-by: Daniel Smith <danct12@disroot.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For systems in which the touch IRQ is acting as wakeup source, and that do
not support level-driven interrupts, the interrupt controller might not
latch the GPIO IRQ during sleep. In such cases, the interrupt will never
occur again after resume, hence the touch screen appears dead.
To fix this, check for the assertion of the attn gpio, and read form the
controller once in the resume path to read the hardware status and
to arm the IRQ again.
Introduce a mutex to guard eeti_ts_read() against parallel invocations
from different contexts.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Sven Neumann <Sven.Neumann@teufel.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A few new drivers:
- driver for Azoteq IQS550/572/525 touch controllers
- driver for Microchip AT42QT1050 keys
- driver for GPIO controllable vibrators
- support for GT5663 in Goodix driver
... along with miscellaneous driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - mark expected switch fall-through
Input: qt1050 - add Microchip AT42QT1050 support
Input: add support for Azoteq IQS550/572/525
Input: add a driver for GPIO controllable vibrators
Input: synaptics-rmi4 - fix enum_fmt
Input: synaptics-rmi4 - fill initial format
HID: input: add mapping for KEY_KBD_LAYOUT_NEXT
Input: add KEY_KBD_LAYOUT_NEXT
Input: hyperv-keyboard - add module description
Input: olpc_apsp - depend on ARCH_MMP
Input: sun4i-a10-lradc-keys - add support for A83T
Input: snvs_pwrkey - use dev_pm_set_wake_irq() to simplify code
Input: lpc32xx-key - add clocks property and fix DT binding example
Input: i8042 - signal wakeup from atkbd/psmouse
Input: goodix - add GT5663 CTP support
Input: goodix - add regulators suppot
Input: evdev - use struct_size() in kzalloc() and vzalloc()
Input: edt-ft5x06 - convert to use SPDX identifier
Input: edt-ft5x06 - enable ACPI enumeration
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzPgx4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf8IH/jkes7tKj7pWfsNW
uMjbm5T+Jh26sntRj+3OWOxcHRlejTH2MammnA9GIspBfF5LXkkmk40eeYhnTiVN
SzZqSFNLO0tRIHsd7hbxhTyOzHcWmymoEqY1jb8IPMyM5BB8TiS+1C0AVlOW1P/f
TO1gRcrddu1j80uCInRzNX5eAlvfrU4nK6GxjFdmy6b/bgYQiPfNA+jZbCWxc+48
ivBn9ifFCKlDzki81Dmi5R98c4R9UU3Z5LsqHjC4RIV64hpHdEwnOIkXQ+XY5mW9
7EOT1v6hJGch1ulH27ypgSZ7fhSCSYQJIY/LNWeJtdVclvlVepb2Vrx/8NUN60qC
E0MEn1Y=
=mCkr
-----END PGP SIGNATURE-----
Merge tag 'v5.1' into next
Sync up with mainline to bring in the latest APIs.
This patch adds support for the Azoteq IQS550/572/525 family of
trackpad/touchscreen controllers.
The driver has been tested with an IQS550EV02 evaluation board. A
demonstration of the driver's capabilities is available here:
https://youtu.be/sRNNx4XZBts
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GT5663 is capacitive touch controller with customized smart
wakeup gestures.
Add support for it by adding compatible and supported chip data.
The chip data on GT5663 is similar to GT1151, like
- config data register has 0x8050 address
- config data register max len is 240
- config data checksum has 16-bit
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix CTP controllers require AVDD28, VDDIO regulators for power-on
sequence.
The delay between these regualtor operations as per Power-on Timing
from datasheet[1] is 0 (T1 >= 0 usec).
So, enable and disable these regulators in proper order using normal
regulator functions without any delay in between.
[1] GT5663 Datasheet_English_20151106_Rev.01
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- update the ili210x touchscreen driver, refreshing the code and adding
support for ILI251X line
- add support for st1633 to the st1232 touchscreen driver
- add support for sx8650 to the the sx8654 touchscreen driver
- add support for Evervision FT5726 to the edt-ft5x06 touchscreen
driver
- add support for gt5688 to the Goodix touchscreen driver
- new vibrator driver for MSM SOCs
- miscellaneous fixes for the rest of input drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: wacom_serial4 - add support for Wacom ArtPad II tablet
Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
Input: msm-vibrator - use correct gpio header
Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
Input: i8042 - rework DT node name comparisons
Input: goodix - print values in case of inconsistencies
Input: goodix - refer to touchscreen.txt in device tree bindings
Input: goodix - support Goodix gt5688
Input: synaptics_i2c - remove redundant spinlock
Input: db9 - mark expected switch fall-through
Input: qt2160 - remove redundant spinlock
Input: st1232 - handle common DT bindings
Input: ims-pcu - switch to using brightness_set_blocking()
Input: st1232 - switch to gpiod API
Input: ili210x - fetch touchscreen geometry from DT
Input: msm-vibrator - tweak an error message
Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
Input: stmfts - acknowledge that setting brightness is a blocking call
Input: ili210x - switch to using devm_device_add_group()
...
When CONFIG_INPUT_POLLDEV is disabled, we get a link error:
drivers/input/touchscreen/raspberrypi-ts.o: In function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0xec): undefined reference to `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0xec): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_input_allocate_polled_device'
raspberrypi-ts.c:(.text+0x19c): undefined reference to `input_register_polled_device'
raspberrypi-ts.c:(.text+0x19c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `input_register_polled_device'
Select that symbol like we do from the other similar drivers.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
While here, correct MODULE_LICENSE() string to be aligned with license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ACPI allows to enumerate specific devices by using compatible strings.
Enable that enumeration for EDT touchscreen devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_suspend':
drivers/input/touchscreen/ti_am335x_tsc.c:510:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/ti_am335x_tsc.c: In function 'titsc_resume':
drivers/input/touchscreen/ti_am335x_tsc.c:527:24: warning:
variable 'tscadc_dev' set but not used [-Wunused-but-set-variable]
It's not used any more after 333e07ec4b ("Input: ti_am335x_tsc: Mark TSC
device as wakeup source")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"Invalid config" gives little idea what's wrong. Print the values that
must not be 0 so we know which ones are off.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is required to specify generic touchscreen properties via DT.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_gpiod_get_optional() and gpiod_set_value_cansleep() instead
of the old API. The st1232_ts_power() now passes on the inverted "poweron"
value to reflect the correct logical value.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fetching the geometry from the ILI251x registers seems unreliable and
sometimes returns all zeroes. Add support for fetching the geometry and
axis inversion from DT instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By switching to devm_device_add_group() we can complete driver conversion
to using managed resources and get rid of ili210x_i2c_remove().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILI251x touch controller. This controller is similar
to the ILI210x, except for the following differences:
- Does not support I2C R-W transfer, Read must be followed by an
obscenely long delay, and then followed by Write
- Does support 10 simultaneous touch inputs.
- Touch data format is slightly different, pressure reporting does not
work although the touch data contain such information.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Perform the register access only after the I2C client data are set,
this is only done in preparation for the subsequent patch which
uses the I2C client data in the register IO function.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the packed structures for representing data as that does not
apply to other similar Ilitek touchscreens. Instead, implement a function
which parses the data and reports touch events and coordinates.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the driver to devm_request_irq(), drop the related unmanaged
deregistration code and add ili210x_irq_teardown() to tear the IRQ
down and cancel possible touchscreen pending work.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen can have a reset GPIO connected to it, add support
for such an arrangement.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The .get_pendown_state callback is set only by the platform data code,
which was just removed. Thus, get_pendown_state() always returns false,
so drop that altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is not a single user of the ili210x platform data in the kernel,
just drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should rely on the interrupt trigger (level vs edge) set up by the
firmware or board code instead of forcing what we consider appropriate.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some of the #defined register values are one-bit flags. Convert them to
use the BIT(x) macro instead of 1 byte hexadecimal values. This improves
readability and clarifies the intent.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
of_touchscreen.c provides a common interface for a axis inversion and
swapping of touchscreens. Therefore use it in the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 and sx8650 are quite similar, therefore add support for the
sx8650 within the sx8654 driver.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: use __be16 in sx8650_irq, add missing del_timer_sync]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the sx865[456] share the same datasheet and differ only in the
presence of a "capacitive proximity detection circuit" and a "haptics
motor driver for LRA/ERM" add them to the compatbiles. As the driver
doesn't implement these features it should be no problem.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sx8654 features a NRST input which may be connected to a GPIO.
Therefore add support for hard-resetting the sx8654 via this NRST.
If the reset-gpio property is provided the sx8654 is resetted via NRST
instead of the soft-reset via I2C.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds myself as an author of the st1232 driver module as Tony's
email address doesn't seem to work anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the Sitronix ST1633 touchscreen controller to the st1232
driver. A protocol spec can be found here:
www.ampdisplay.com/documents/pdf/AM-320480B6TZQW-TC0H.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
This patch removes common ADC settings in favor to use
stmpe811_adc_common_init that is present in MFD. This is necessary in
preparation for the stmpe-adc driver, because those two drivers have
common settings for the ADC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move defines that are ADC related to the header of the overlying MFD,
so they can be used from multiple sub-devices.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into for-linus
Sync with mainline to get linux/overflow.h among other things.
Fix link error when TOUCHSCREEN_RASPBERRYPI_FW is enabled as a module and
the dependent module is built-in. The 'depends on RASPBERRYPI_FIRMWARE' by
itself prevents the touchscreen driver from being built-in when the
firmware is configured as a module. However, the '|| COMPILE_TEST' still
allows it unless we explicitly prevent that configuration with
'|| (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)'.
ld: drivers/input/touchscreen/raspberrypi-ts.o: in function `rpi_ts_probe':
raspberrypi-ts.c:(.text+0x3a8): undefined reference to `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x3a8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_get'
ld: raspberrypi-ts.c:(.text+0x4c8): undefined reference to `rpi_firmware_property'
ld: raspberrypi-ts.c:(.text+0x4c8): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `rpi_firmware_property'
Rework so that TOUCHSCREEN_RASPBERRYPI_FW depends on
RASPBERRYPI_FIRMWARE=n if COMPILE_TEST is enabled.
Fixes: 0b9f28fed3 ("Input: add official Raspberry Pi's touchscreen driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately the evervision focaltech implementation uses two offset
registers, one for the x coordinate and one for y.
This patch extends the driver to handle those offset registers only for
devices that support these.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently only the threshold and gain parameters can be read.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Evervision displays are using different Focaltech touchscreen
controllers. This commit adds the initial support for the ones using the
FT5726 controller. Receiving the touch data is the same as for the
GENERIC_FT but the x and y cooridnates are swapped. The main differences
are the register addresses where the GAIN and THRESHOLD parameters are
stored.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into next
Merge with mainline to bring in the new APIs.
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
regmap_bulk_read() can return a non zero value on failure. The fix checks
if the function call succeeded before calling mod_timer. The issue was
identified by a static analysis tool.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A tiny pull request this merge window unfortunately, should get more
material in for the next release:
- new driver for Raspberry Pi's touchscreen (firmware interface)
- miscellaneous input driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G
Input: atmel_mxt_ts - don't try to free unallocated kernel memory
Input: drv2667 - fix indentation issues
Input: touchscreen - fix coding style issue
Input: add official Raspberry Pi's touchscreen driver
Input: nomadik-ske-keypad - fix a loop timeout test
Input: rotary-encoder - don't log EPROBE_DEFER to kernel log
Input: olpc_apsp - remove set but not used variable 'np'
Input: olpc_apsp - enable the SP clock
Input: olpc_apsp - check FIFO status on open(), not probe()
Input: olpc_apsp - drop CONFIG_OLPC dependency
clk: mmp2: add SP clock
dt-bindings: marvell,mmp2: Add clock id for the SP clock
Input: ad7879 - drop platform data support
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes the coding style problem reported
by checkpatch.pl as below:
ERROR: foo* bar should be "foo *bar"
Signed-off-by: Hardik Singh Rathore <hardiksingh.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add's support to Raspberry Pi's 7" Touch device. Instead of using a
conventional bus all information is copied into a memory mapped area by
RPi's firmware.
Based on the driver found in RPi's kernel repository.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
This driver supports configuration via platform data but
absolutely nothing in the upstream kernel uses it. Since this
configuration allows harmful practices such as encoding the
GPIO base for the chip, delete platform data support so that
no new platform using it gets introduced.
Also: include the right driver header, not <linux/gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
