Gotos jumping to a return statement are not really useful, drop them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-42-miquel.raynal@bootlin.com
These warnings are reported by checkpatch.pl essentially.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-41-miquel.raynal@bootlin.com
Drop the text license and replace it with an equivalent SPDX license tag
identifier which also matches the MODULE_LICENSE("GPL").
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-40-miquel.raynal@bootlin.com
At least on a am4372, a simple:
$ cat /sys/bus/iio/devices/iio\:deviceX/in_voltage*_raw
can stall forever. It seems that it comes from the fact that the
internal state machine does not have enough time to return to its idle
state in this situation before receiving another request, leading to an
internal stall.
Add a tiadc_wait_idle() helper to ensure no new conversion is requested
while the FSM is still busy.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-39-miquel.raynal@bootlin.com
This bit is common to all devices (ADC, Touchscreen, Magnetic reader) so
make it clear that it can be used from any location by operating a
mechanical rename:
s/CNTRLREG_TSCSSENB/CNTRLREG_SSENB/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-31-miquel.raynal@bootlin.com
Clearly define the maximum open delay and sample delay. Use these
definitions in place of a mask (which works because this is the first
field in the register) and an open-coded value. While at it reword a
little bit the error messages to make them look clearer and similar.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-29-miquel.raynal@bootlin.com
Clean the ti_am335x_tscadc.h header by:
* converting masks to GENMASK()
* converting regular shifts to BIT()
* using FIELD_PREP() when relevant
Sometimes reorder the lines to be able to use the relevant bitmask.
Mind the s/%d/%ld/ change in a log due to the type change following the
use of FIELD_PREP() in the header.
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-28-miquel.raynal@bootlin.com
Add st,min-sample-time-nsecs to channel generic binding.
Sample time can be defined par channel node. If a channel
is configured as differential, the same sample time applies
for both inputs.
Keep support of legacy st,min-sample-time-nsecs property
for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-8-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of vrefint calibration.
If a channel is labeled as vrefint, get vrefint calibration
from non volatile memory for this channel.
vrefint channel is exposed as a processed channel returning
the actual value of vrefp:
vrefp = 3.3 x vrefint_cal / vrefint_data
A conversion on vrefint channel allows to update scale
factor according to vrefint deviation, compared to vrefint
calibration value.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-7-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of ADC2 internal channels VDDCORE, VREFINT and VBAT.
The reserved label name "vddcore", "vrefint" and "vbat" must
be used in Device Tree channel node, to enable the corresponding
internal channel.
Note: This patch does not provide support of internal channels
for F4 and H7.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-6-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of generic IIO channel binding:
./devicetree/bindings/iio/adc/adc.yaml
Keep support of st,adc-channels and st,adc-diff-channels
for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-5-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Split stm32_adc_chan_of_init channel initialization function into
several routines to increase readability and prepare channel
generic binding handling.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20211014131228.4692-4-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 2a9685d1a3 ("iio: adc: xilinx: use more devres helpers and
remove remove()") the `irq` field from XADC driver state struct is only
used in the `probe()` function.
Use the local `irq` variable throughout the `probe()` function and remove
the now unused field from the state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211017121551.24063-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-9-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-8-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
BTW, change the return value from 'ENXIO' to 'ENODEV',
perfer ENODEV which means no such device.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211008092858.495-7-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> #Meson8b Odroid-C1
Link: https://lore.kernel.org/r/20211008092858.495-6-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-5-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-4-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
Using dev_err_probe() can reduce code size, and the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211008092858.495-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The remove function and the goto sections are not necessary if devm
functions are used.
Convert device register to devm version. Add hook functions to release
device resources, and use them inside probe with devm_add_action,
which will release resources on driver detach.
To maintain the order of which device resources were released/reseted,
register the hook functions as soon as resources are obtained/initialized.
Since devres actions are called on driver detach, the remove
function and the error-handling goto sections are no longer necessary.
Signed-off-by: André Gustavo Nakagomi Lopez <andregnl@usp.br>
Link: https://lore.kernel.org/r/YWnMsGlc/I35gYvy@Andryuu.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
-----BEGIN PGP SIGNATURE-----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=htmG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO new device and feature support for the 5.16 cycle
Counter subsystem changes now sent separately.
This has been a busy cycle, so lots here and a few more stragglers to
come next week.
Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.
New device support
------------------
* adi,adxl313
- New driver and dt bindings for this low power accelerometer.
* adi,adxl355
- New driver and dt bindings for this accelerometer.
- Later series adds buffer support.
* asahi-kasei,ak8975
- Minor additions to driver to support ak09916
* aspeed,aspeed-adc
- Substantial rework plus feature additions to add support for the
ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
- Rework and support introduced for the sama7g5 parts.
* maxim,max31865
- New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
- New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
- New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
- New driver and bindings for this carbon dioxide gas sensor.
New features
------------
* Output buffer support. Works in a similar fashion to input buffers, but
in this case userspace pushes data into the kfifo which is then drained
to the device when a trigger occurs. Support added to the ad5766 DAC
driver.
* Core, devm_iio_map_array_register() to avoid need for
devm_add_action_or_reset() based cleanup in fully managed allocation
drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
few drivers where it really hard to ensure the correct data alignment in
an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
buffer so should be avoided whenever possible. Used in the ti,adc108s102,
invense,mpu3050 and adi,adis16400. This closes the last known set
of drivers with alignment issues at this interface.
* maxim,max1027
- Substantial rework to this driver main target of which was supporting
use of other triggers than it's own EOC interrupt.
- Transfer optimization.
* nxp,fxls8962af
- Threshold even support including using it as a wakeup source.
Cleanups, minor fixes etc
-------------------------
Chances of a common type to multiple drivers:
* devm_ conversion and drop of .remove() callbacks in:
- adi,ad5064
- adi,ad7291
- adi,ad7303
- adi,ad7746
- adi,ad9832
- adi,adis16080
- dialog,da9150-gpadc
- intel,mrfld_adc
- marvell,berlin2
- maxim,max1363
- maxim,max44000
- nuvoton,nau7802
- st_sensors (includes a lot of rework!)
- ti,ads8344
- ti,lp8788
* devm_platform_ioremap_resource() used to reduce boilerplate
- cirrus,ep93xx
- rockchip,saradc
- stm,stm32-dac
* Use dev_err_probe() in more places to both not print on deferred probe and
ensure a reason for the deferral is available for debug purposes.
- adi,ad8801
- capella,cm36651
- linear,ltc1660
- maxim,ds4424
- maxim,max5821
- microchip,mcp4922
- nxp,lpc18xx
- onnn,noa1305
- st,lsm9ds0
- st,st_sensors
- st,stm32-dac
- ti,afe4403
- ti,afe4404
- ti,dac7311
* Drop error returns in SPI and I2C remove() functions as they are ignored and
long term plan is to change these all over to returning void. In some cases
these patches just make it 'obvious' they always return 0 where it was the
case before but not easy to tell.
- adi,ad5380
- adi,ad5446
- adi,ad5686
- adi,ad5592r
- bosch,bma400
- bosch,bmc150
- fsl,mma7455
- honeywell,hmc5843
- kionix,kxsd9
- maxim,max5487
- meas,ms5611
- ti,afe4403
Driver specific changes
* adi,ad5770r
- Bring driver inline with documented bindings.
* adi,ad7746
- Trivial style fix
* adi,ad7949
- Express some magic values as the underlying parts via new #defines.
- Make it work with SPI controllers that don't support 14 or 16 bit messages
- Support selection of voltage reference from dt including expanding the
dt-bindings to cover this new functionality.
* adi,ad799x
- Implement selection of external reference voltage on AD7991, AD7995 and
AD7999.
- Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
- Move interrupt startup to better location in startup flow.
- Handle devices that cannot mask/unmask the drdy pin and must instead mask
at the interrupt controller. Applies to the adis16460 and adis16475 from
which we then drop equivalent code.
* adi,ltc2983
- Add support for optional reset pin.
- Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
- dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
- Typo fix.
* fsl,mma7660
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
- Avoid initializing regulators that aren't used.
* invensense,mpu3050
- Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
- Rework code to not use strcpy() and hence avoid possibility of wrong sized
buffers. Note this wasn't a bug, but the new code is a lot more readable.
- Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
- dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
- Enable COMPILE_TEST building.
* maxim,max1027
- Avoid returning success in an error path.
* nxp,imx8qxp
- Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
- Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
- Improve kconfig help text.
* st,lsm6dsx
- Move max_fifo_size into the fifo_ops structure where the other configuration
parameters are found.
* st,st_sensors:
- Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
- Add missing I2C dependency.
* ti,twl6030
- Small code tidy up.
* tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (148 commits)
iio: imx8qxp-adc: mark PM functions as __maybe_unused
iio: pressure: ms5611: Make ms5611_remove() return void
iio: potentiometer: max5487: Don't return an error in .remove()
iio: magn: hmc5843: Make hmc5843_common_remove() return void
iio: health: afe4403: Don't return an error in .remove()
iio: dac: ad5686: Make ad5686_remove() return void
iio: dac: ad5592r: Make ad5592r_remove() return void
iio: dac: ad5446: Make ad5446_remove() return void
iio: dac: ad5380: Make ad5380_remove() return void
iio: accel: mma7455: Make mma7455_core_remove() return void
iio: accel: kxsd9: Make kxsd9_common_remove() return void
iio: accel: bmi088: Make bmi088_accel_core_remove() return void
iio: accel: bmc150: Make bmc150_accel_core_remove() return void
iio: accel: bma400: Make bma400_remove() return void
drivers:iio:dac:ad5766.c: Add trigger buffer
iio: triggered-buffer: extend support to configure output buffers
iio: kfifo-buffer: Add output buffer support
iio: Add output buffer support
iio: documentation: Document scd4x calibration use
drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
...
Without CONFIG_PM_SLEEP, the runtime suspend/resume functions
are unused, producing a warning:
drivers/iio/adc/imx8qxp-adc.c:433:12: error: 'imx8qxp_adc_runtime_resume' defined but not used [-Werror=unused-function]
433 | static int imx8qxp_adc_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/imx8qxp-adc.c:419:12: error: 'imx8qxp_adc_runtime_suspend' defined but not used [-Werror=unused-function]
419 | static int imx8qxp_adc_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Mark them as __maybe_unused to shut up the compiler.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211013144338.2261316-1-arnd@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that output (kfifo) buffers are supported, we need to extend the
{devm_}iio_triggered_buffer_setup_ext() parameter list to take a direction
parameter.
This allows us to attach an output triggered buffer to a DAC device.
Unfortunately it's a bit difficult to add another macro to avoid changing 5
drivers where {devm_}iio_triggered_buffer_setup_ext() is used.
Well, it's doable, but may not be worth the trouble vs just updating all
these 5 drivers.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mihail Chindris <mihail.chindris@analog.com>
Link: https://lore.kernel.org/r/20211007080035.2531-4-mihail.chindris@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of the AD7991_REF_SEL bit and support using the external
reference voltage if 'vref-supply' is present. Use VCC voltage supply
as reference if no extra reference is supplied.
Signed-off-by: Florian Boor <florian.boor@kernelconcepts.de>
Link: https://lore.kernel.org/r/20210930104249.2924336-1-florian.boor@kernelconcepts.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Return -ETIMEDOUT on timeout instead of success.
Fixes: 1f7b4048b3 ("iio: adc: max1027: Use the EOC IRQ when populated for single reads")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the newly introduce iio_push_to_buffers_with_ts_unaligned() function
to ensure a bounce buffer is used to provide the required alignment and
space padding needed by the IIO core which requires the timestamp
is naturally aligned. There will be a performance cost to this change
but it will ensure the driver works on platforms that do not support
unaligned 8 byte assignments, and with consumer drivers that may
assume natural alignment of the timestamp.
Issue found as part of an audit of all calls to
iio_push_to_buffers_with_timestamp()
Fixes: 7e87d11c9b ("iio: adc: Add support for TI ADC108S102 and ADC128S102")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20210613151039.569883-3-jic23@kernel.org
This is a simple conversion for to device-managed with using
devm_request_threaded_irq(), disabling the regulator via a
devm_add_action_or_reset() hook and finally using
devm_iio_device_register().
The i2c_set_clientdata() call is removed as it becomes redundant after this
change.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926194315.7742-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Otherwise most build checks will omit this driver from a compile-test due
to it's dependency only on the BERLIN_ARCH symbol.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926192642.4051329-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver requires only a devm_add_action_or_reset() hook for the
power-down of the device, and then devm_iio_device_register() can be used
directly.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926192642.4051329-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver already hooks a similar unwind callback via
devm_add_action_or_reset().
They pretty much do the same thing, so this change converts it to the
devm_iio_map_array_register().
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20210926162859.3567685-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For this conversion, the 2 regulators (being enabled) require each a
devm_add_action_or_reset() hook registration.
For the other functions, there are device-managed variants.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926162110.3536436-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a trivial conversion to device-managed functions.
The mutex_destroy() calls are redundant, as the data will be free'd anyway.
And the IRQ and IIO register functions both have device-managed
equivalents.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210926154932.3287590-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903072917.45769-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903072917.45769-5-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903072917.45769-4-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only call in the remove hook is the iio_map_array_unregister() call.
Since we have a devm_iio_map_array_register() function now, we can use that
and remove the remove hook entirely.
The IIO device was registered with the devm_iio_device_register() prior to
this change.
Also, the platform_set_drvdata() can be removed now, since it was used only
in the remove hook.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210903072917.45769-3-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver tries to initialize all possible regulators from the DT, then
match the external regulators with each channel and then release all unused
regulators.
We can change the logic a bit to initialize regulators only when at least
one channel needs them.
This change creates a mx25_gcq_ext_regulator_setup() function that is
called only for the external regulators. If there's already a reference to
an external regulator, the function will just exit early with no error.
This way, the driver doesn't need to keep any track of these regulators
during init.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210625074325.9237-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
External triggers do not necessarily need the EOC interrupt to be
populated to work properly. The end of conversion status may either come
from an interrupt or from a sufficient enough extra delay. IRQs are not
mandatory so move the triggered buffer setup out of the IRQ condition
and add the logic to wait enough time for all the requested conversions
to be in the device's FIFO.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-17-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no reason to limit this driver to its internal trigger. The
only difference being, when using an external trigger, the sample
conversion must be manually started.
Drop the ->validate_trigger() hook in order to allow other triggers to
be bound.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-16-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
So far the End-Of-Conversion interrupt was only used in conjunction with
the internal trigger to process the data. Let's extend the use of this
interrupt handler to support regular single-shot conversions as well.
Doing so requires writing our own hard IRQ handler. This handler has to
check if buffers are enabled or not:
*** Buffers disabled condition ***
This means the user requested a single conversion and the sample is
ready to be retrieved.
-> This implies adding the relevant completion boilerplate.
*** Buffers enabled condition ***
Triggers are used. So far there is only support for the internal
trigger but this trigger might soon be attached to another device as
well so it is the core duty to decide which handler to call in order
to process the data. The core will decide to either:
* Call the internal trigger handler which will extract the data that
is already present in the ADC FIFOs
or
* Call the trigger handler of another driver when using this trigger
with another device, even though this call will be slightly delayed
by the fact that the max1027 IRQ is a data-ready interrupt rather
than a real trigger:
-> The new handler will manually inform the core about the trigger
having transitioned by directly calling iio_trigger_poll() (which
iio_trigger_generic_data_rdy_poll() initially did).
In order for the handler to be "source" agnostic, we also need to change
the private pointer and provide the IIO device instead of the trigger
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-15-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The threaded handler is not populated, this means there is nothing
running in process context so let's switch to the regular
devm_request_irq() call instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-14-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For now this helper only waits for the maximum duration of a single
conversion.
In practice, a "temperature measurement" will take twice this
time because it will also carry another analog conversion but as here we
will only care about the temperature conversion which happens first, we
can still only wait for a single sample and get the right data.
This helper will soon be improved to properly handle the end of
conversion interrupt as well as a higher number of samples.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create a max1027_read_scan() helper which will make clearer the future IRQ
handler updates (no functional change).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-12-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When hardware buffers are enabled (the cnvst pin being the trigger), one
should not mess with the device state by requesting a single channel
read.
There is already a iio_buffer_enabled() check in *_read_single_value()
to merely prevent this situation but the check is inconsistent since
buffers can be enabled after the if clause anyway. Instead, use the core
mutex by calling iio_device_claim/release_direct_mode().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-11-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We don't expect the (hardware) cnvst trigger to be enabled at boot time,
this is a user choice made in sysfs and there is a dedicated callback to
enable/disable this trigger. Hence, we can just ensure it is disabled in
the probe at initialization time and then assume that whenever a
->read_raw() call happens, the trigger has been disabled and conversions
will start on register write.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-9-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The call to max1027_enable_trigger() is the same in both cases thanks to
the 'state' variable, so factorize a little bit to simplify the code and
explain why we call this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-8-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are two ways to physically trigger a conversion:
- A falling edge on the cnvst pin
- A write operation on the conversion register
Let's create a helper for this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-7-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it clear that the *_set_trigger_state() hook is responsible for
cnvst based conversions by renaming the helper. This may avoid
confusions with software trigger support that is going to be
introduced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-6-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.
The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.
For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.
Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Memory allocation errors automatically trigger the right logs, no need
to have our own.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow checkpatch.pl's main advices before hacking into the driver, mainly:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int *' to bare use of 'unsigned *'
CHECK: Comparison to NULL could be written "!foo"
CHECK: Alignment should match open parenthesis
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sync if statement with the actual warning.
Fixes: 9504db5765 ("iio: adc: tsc2046: fix a warning message in tsc2046_adc_update_scan_mode()")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007093007.1466-2-o.rempel@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105631.1474-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105646.1576-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The previous driver does't apply the necessary scaling to take the
voltage range into account.
We change readback value from raw data to input voltage to fix case
IIO_CHAN_INFO_PROCESSED.
Fixes: ace4cdfe67 ("iio: adc: mt2701: Add Mediatek auxadc driver for mt2701.")
Signed-off-by: Hui Liu <hui.liu@mediatek.com>
Link: https://lore.kernel.org/r/20210926073028.11045-2-hui.liu@mediatek.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add clk_disable_unprepare() on error path in rzg2l_adc_pm_runtime_resume().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210819132416.175644-1-yangyingliang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The macro MAX1X29_CHANNELS() already calls MAX1X27_CHANNELS().
Calling MAX1X27_CHANNELS() before MAX1X29_CHANNELS() in the definition
of MAX1X31_CHANNELS() declares the first 8 channels twice. So drop this
extra call from the MAX1X31 channels list definition.
Fixes: 7af5257d84 ("iio: adc: max1027: Prepare the introduction of different resolutions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
10-bit devices must shift the value twice.
This is not needed anymore on 12-bit devices.
Fixes: ae47d009b5 ("iio: adc: max1027: Introduce 12-bit devices support")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A successful 'regulator_enable()' call should be balanced by a
corresponding 'regulator_disable()' call in the error handling path of the
probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: 913b864686 ("iio: adc: Add TI ADC128S052")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/85189f1cfcf6f5f7b42d8730966f2a074b07b5f5.1629542160.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently when a timeout occurs in rzg2l_adc_hw_init the error -EBUSY is
assigned to ret but the error code is used as the function is hard-coded
to return 0. The variable ret is 0 before entering the while-loop hence
the fix is just to return ret at the end of the function to return the
success 0 or -EBUSY return code.
Addresses-Coverity: ("Unused value")
Fixes: d484c21bac ("iio: adc: Add driver for Renesas RZ/G2L A/D converter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210817172111.495897-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch completes the declare of ADC register bitfields and uses the
same prefix ASPEED_ADC_* for these bitfields. In addition, tidy up space
alignment of the codes.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210831071458.2334-4-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the driver to register via devm_iio_device_register().
The regulator disable is moved on a devm_add_action_or_reset() hook.
And the spi_set_drvdata() isn't required anymore.
And finally, the ads8344_remove() can be removed as well.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903073707.46892-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update copyright and authors information (corrected e-mail address), and
add myself as one of the authors.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-9-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to sama7g5 ADC which is similar with sama5d2/sam9x60 device.
Differences are highlighted by compatible.
Main differences include 16 channels instead of 12 and missing
resistive touchscreen.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-8-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add helper for the COR register. This helper allows to modify the COR
register, removes duplicate code and improves readability.
The COR offset is now part of the register layout. This will allow
different platform with a different offset to use the same helper.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-7-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some platforms have separated the end-of-conversion information from the
usual ISR/IMR/IER/IDR registers, into EOC_ISR/EOC_IMR/EOC_IER/EOC_IDR.
To cope with both variants, helpers are being added, that will make
code more clear and more easy to read.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-6-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the driver to platform specific structures. This means:
- create a register layout struct that will hold offsets for registers
- create a platform struct that will hold platform information (number of
channels, indexes for different channels and pointer to layout struct)
- convert specific macros that are platform dependent into platform variables
This step is in fact a no-op, but allows the driver to be more flexible
and for future enhancement including adding new platforms that are partly
compatible with the current driver and differ slightly in register layout
or capabilities for example.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-5-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hw_init hardware init call must happen after the clock is prepared and
enabled. Otherwise, writing to the registers might lead to a block or
external abort.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-3-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch to devm_iio_device_register to finalize devm migration.
This removes the use for iio_device_unregister() and since
mutex_destroy() is not necessary here, remove it altogether.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-6-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for selecting the voltage reference from the devicetree.
This change is required to get valid readings with all three
vref hardware configurations supported by the ADC.
For instance if the ADC isn't provided with an external reference,
the sample request must specify an internal voltage reference to get a
valid reading.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports devices with 14-bit and 16-bit sample sizes.
This implies different SPI transfer lengths which are not always handled
properly by some SPI controllers.
To work around this limitation, define a big endian buffer used to split
the buffer into two 8-bit messages in the event that the controller
doesn't support 14-bit or 16-bit transfers.
A separate buffer is introduced here to avoid performing operations on
types of different endianness.
Since all transfers use the same bits_per_word value, move that logic to
the probe function, and let transfers default to the value defined in
the struct spi_device.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-3-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had been
maintained out-of-tree by Larry with the end goal of actually being able
to get this driver out of staging eventually. Despite that driver being
"newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to see,
that is why there are additions to the mfc and misc driver subsystems.
All of these were acked by the various subsystem maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+BKg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yku5gCgyMykJ2mwtEiQxfAWu13e2iZX29AAnjk38ANp
Un2sQXYnL9RVlcnjLg+X
=jMWL
-----END PGP SIGNATURE-----
Merge tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO and staging driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had
been maintained out-of-tree by Larry with the end goal of actually
being able to get this driver out of staging eventually. Despite that
driver being "newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to
see, that is why there are additions to the mfc and misc driver
subsystems. All of these were acked by the various subsystem
maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems"
[ Note: the r8188eu merge clashed with commit 89939e8906 ("staging:
rtlwifi: use siocdevprivate") from the networking tree. When resolving
the issue, I noted that the whole r8188eu rtw_android code is dead
since commit ae7471cae0 ("staging: r8188eu: remove rtw_ioctl
function").
End result: the merge resolution was to throw all of that away,
rather than do the mindless fixup to code that isn't actually
reachable - Linus ]
* tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (551 commits)
staging: vt6655: Remove filenames in files
staging: r8188eu: add extra TODO entries
staging: vt6656: Remove filenames in files
staging: wlan-ng: fix invalid assignment warning
staging: r8188eu: rename fields of struct rtl_ps
staging: r8188eu: remove ODM_DynamicPrimaryCCA_DupRTS()
staging: r8188eu: rename fields of struct dyn_primary_cca
staging: r8188eu: rename struct field Wifi_Error_Status
staging: r8188eu: Provide a TODO file for this driver
staging: r8188eu: remove unneeded variable
staging: r8188eu: remove unneeded conversions to bool
staging: r8188eu: remove {read,write}_macreg
staging: r8188eu: core: remove condition with no effect
staging: r8188eu: remove ethernet.h header file
staging: r8188eu: remove ip.h header file
staging: r8188eu: remove if_ether.h header file
staging: r8188eu: make rtw_deinit_intf_priv return void
staging: r8188eu: use is_multicast_ether_addr in os_dep/recv_linux.c
staging: r8188eu: use is_multicast_ether_addr in hal/rtl8188eu_xmit.c
staging: r8188eu: use is_multicast_ether_addr in core/rtw_xmit.c
...
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
-----BEGIN PGP SIGNATURE-----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=d/Fm
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd set of new IIO device support and cleanups for the 5.15 cycle.
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
* tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: Add driver for Renesas RZ/G2L A/D converter
dt-bindings: iio: adc: Add binding documentation for Renesas RZ/G2L A/D converter
iio: pressure: hp03: update device probe to register with devm functions
iio: adc: rockchip_saradc: add voltage notifier so get referenced voltage once at probe
iio: ltc2983: fix device probe
iio: potentiometer: Add driver support for AD5110
dt-bindings: iio: potentiometer: Add AD5110 in trivial-devices
