[why]
driver missed the check.
[how]
add the check.
add min display clock = 100mhz check based on dccg doc.
[note]
add SetPhyclkVoltageByFreq as confirmed with smu, but not enabled in
this change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP will suspend and resume DMCUB. Driver should just wait for DMCUB to
finish the auto load before continuining instead of placing it into
reset, wiping its firmware state and reinitializing.
If we don't let DMCUB fully finish initializing for S0ix then some state
will be lost and screen corruption can occur due to incorrect address
translation.
[How]
Use dmub_srv callbacks to determine in DMCUB is running and wait for
auto-load to complete before continuining.
In S0ix DMCUB will be running and DAL fw so initialize will skip.
In S3 DMCUB will not be running and we will do a full hardware init.
In S3 DMCUB will be running but will not be DAL fw so we will also do
a full hardware init.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. Current code hard codes link to PHY mapping in dc link level per asic
per revision.
This is not scalable. In long term the mapping will be obatined from
DMUB and store in dc resource.
2. Depending on DCN revision and endpoint type, the definition of
dio_output_idx dio_output_type and phy_idx are not consistent. We need
to unify the meaning of these hardware indices across different system
configuration.
[how]
1. Temporarly move the hardcoded mapping to dc_resource level, which
should have full awareness of asic specific configuration and add a TODO
comment to move the mapping to DMUB.
2. populate dio_output_idx/phy_idx for all configuration, define
usb4_enabled bit instead of dio_output_type as an external enum.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Depend on res_pool->res_cap->num_timing_generator to query timing
gernerator information, it would case underflow at the fused display
pipes case.
Due to the res_pool->res_cap->num_timing_generator records default
timing generator resource built in driver, not the current chip.
[How]
Some ASICs would be fused display pipes less than the default setting.
In dcnxx_resource_construct function, driver would obatin real timing
generator count and store it into res_pool->timing_generator_count.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This makes it clearer which codepaths are in use specifically in
one state or the other.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This codepath should be running in both s0ix and s3, but only does
currently because s3 and s0ix are both set in the s0ix case.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To pair with the workaround which always reset the ASIC in suspend.
Otherwise, the reset which relies on BACO will fail.
Fixes: daf8de0874 ("drm/amdgpu: always reset the asic in suspend (v2)")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Malicious mailbox event1 fails driver loading on vega10.
A dummy event6 prevent driver from taking response from malicious event1 as its own.
[how]
On vega10, send a mailbox event6 before sending event1.
Signed-off-by: James Yao <yiqing.yao@amd.com>
Reviewed-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we are the primary adapter (i.e., the one used by the firwmare
framebuffer), disable runtime pm. This fixes a regression caused
by commit 55285e21f0 which results in the displays waking up
shortly after they go to sleep due to the device coming out of
runtime suspend and sending a hotplug uevent.
v2: squash in reworked fix from Evan
Fixes: 55285e21f0 ("fbdev/efifb: Release PCI device's runtime PM ref during FB destroy")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=215203
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1840
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To pair with the workaround which always reset the ASIC in suspend.
Otherwise, the reset which relies on BACO will fail.
Fixes: daf8de0874 ("drm/amdgpu: always reset the asic in suspend (v2)")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This merges two fixes that haven't been sent to me yet, but I wanted to get in.
One amdgpu fix, but one nouveau regression fixer.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chips with no display hardware should return false for
DC support.
v2: drop Arcturus and Aldebaran
Fixes: f7f12b2582 ("drm/amdgpu: default to true in amdgpu_device_asic_has_dc_support")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reported-by: Tareque Md.Hanif <tarequemd.hanif@yahoo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "plane_state" pointer was access before checking if it was NULL.
Avoid a possible NULL pointer dereference by accessing the plane
address after the check.
Addresses-Coverity-ID: 1493892 ("Dereference before null check")
Fixes: 3f68c01be9 ("drm/amd/display: add cyan_skillfish display support")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the platform suspend happens to fail and the power rail
is not turned off, the GPU will be in an unknown state on
resume, so reset the asic so that it will be in a known
good state on resume even if the platform suspend failed.
v2: handle s0ix
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By setting mp1_state as PP_MP1_STATE_UNLOAD, MP1 will do some proper cleanups and
put itself into a state ready for PNP. That can workaround some random resuming
failure observed on BOCO capable platforms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function enable_stream_features(), the variable "old_downspread.raw"
could be uninitialized if core_link_read_dpcd() fails, however, it is
used in the later if statement, and further, core_link_write_dpcd()
may write random value, which is potentially unsafe.
Fixes: 6016cd9dba ("drm/amd/display: add helper for enabling mst stream features")
Cc: stable@vger.kernel.org
Signed-off-by: Yizhuo Zhai <yzhai003@ucr.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's not only supported by HG/PX laptops. It's supported
by all dGPUs which supports BOCO/BACO functionality (runtime
D3).
BOCO - Bus Off, Chip Off. The entire chip is powered off.
This is controlled by ACPI.
BACO - Bus Active, Chip Off. The chip still shows up
on the PCI bus, but the device itself is powered
down.
v2: fix missed HG/PX reference
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
== Description ==
Setting values of pm attributes through sysfs
should not be allowed in SRIOV mode.
These calls will not be processed by FW anyway,
but error handling on sysfs level should be improved.
== Changes ==
This patch prohibits performing of all set commands
in SRIOV mode on sysfs level.
It offers better error handling as calls that are
not allowed will not be propagated further.
== Test ==
Writing to any sysfs file in passthrough mode will succeed.
Writing to any sysfs file in ONEVF mode will yield error:
"calling process does not have sufficient permission to execute a command".
Signed-off-by: Marina Nikolic <Marina.Nikolic@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise the RAS error count couldn't be queried from sysfs.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Stanley.Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A minor typo.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When reboot the link res map should be persisted. So during boot up,
driver will look at the map to determine which link should take priority
to use certain link res. This is to ensure that link res remains
unshuffled after a reboot.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When there are more DP2.0 RXs connected than the number HPO DP link
encoders we have, we need to dynamically allocate HPO DP link encoder to
the port that needs it.
[how]
Only allocate HPO DP link encoder when it is needed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Update all accesses to use hpo dp link encoder through link resource
only.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This commit is to populate link res in preparation of the next commit.
The next commit will replace all existing code to use link res instead
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There will be a series of re-arch changes in Link Resource Management.
They are more and more muxable link resource objects and the resource is
insufficient for a one to one allocation to all links created.
Therefore a link resource sharing logic is required to determine which
link should use certain link resource.
This commit is the first one in this series that starts by defining a
link resource struct, this struct will be available to all interfaces
that need to perform link programming sequence.
In later commits, we will granduately decouple link resource objects out
of dc link. So instead of access a link resource from dc link. Current
link's resource can be accessible through pipe_ctx->link_res during
commit, or by calling dc_link_get_cur_link_res function with current
link passed in after commit.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Fixes and improvements in the LTTPR code
- Improve z-state
- Fix null pointer check
- Improve communication with s0i2
- Update multiple-display split policy
- Add missing registers
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These registers are currently missing from the DCN303 header files
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll exit optimized power state to do link detection but we won't enter
back into the optimized power state.
This could potentially block s2idle entry depending on the sequencing,
but it also means we're losing some power during the transition period.
[How]
Hook up the handler like DCN21. It was also missed like the
exit_optimized_pwr_state callback.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP spec specifies that DPRX shall use the read interval in the
TRAINING_AUX_RD_INTERVAL_PHY_REPEATER LTTPR DPCD register. This
register's bit definition is the same as the AUX read interval register
for DPRX.
[How}
Remove logic which forces AUX read interval to 100us for repeaters when
in LTTPR non-transparent mode.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise SMU won't mark Display as idle when trying to perform s2idle.
[How]
Mark the bit in the dcn31 codepath, doesn't apply to older ASIC.
It needed to be split from phy refclk off to prevent entering s2idle
when PSR was engaged but driver was not ready.
Fixes: 118a331516 ("drm/amd/display: Add DCN3.1 clock manager support")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bug fix for null function ptr (should check for NULL instead of not
NULL)
[How]
Fix if condition
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change of setting a timer callback on boot for 10 seconds is still
working, just lacked power down for DCN10.
[How]
Added power down for DCN10.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stutter period won't be less than 5000.0, but if PSR is enabled then we
can potentially enter Z9 when MPO is enabled.
SMU will try to enter Z9 too early in these cases (before PSR is
enabled) and we'll see underflow.
[How]
Block z-states (z9, z10) until we can add a new interface to SMU to
signal when we can support z10 but not z9.
We can revert this once the interface change is in.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current implementation is not scalable and retrofits the existing
standard link training code for purposes outside of its original design.
[How]
Refactor vendor specific link training sequence into its own separate
function to be called instead of the standard link training function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Max link rate should be limited to the maximum link rate support by any
LTTPR that are connected, including when operating in transparent mode.
[How]
Include transparent mode when factoring in LTTPR max supported link
rate.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
B0 PHY C map to F, D map to G driver use logic instance, dmub does the
remap. Driver still need use the right PHY instance to access right HW.
[how]
use phyical instance when program PHY register.
[note]
could move resync_control programming to dmub next.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the event guard is enabled and VF doesn't receive an ack from PF for full access,
the guest driver load crashes.
This is caused due to the call to ttm_device_clear_dma_mappings with non-initialized
mman during driver tear down.
This patch adds the necessary condition to check if the mman initialization passed or not
and takes the path based on the condition output.
Signed-off-by: Surbhi Kakarya <Surbhi.Kakarya@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch keeps the setting of sdma queue number to the same
after recent KFD code refactor. Additionally, improve code to
use switch case to list IP version to complete kfd device_info
structure filling for IH version assignment. This makes consistency
with the IP parse code in amdgpu_discovery.c.
v2: use dev_warn for the default switch case;
set default sdma queue per engine(8) and IH handler to v9. (Jonathan)
v3: Fix missed IP version check of Raven.
Fixes: f0dc99a6f7 ("drm/amdkfd: add kfd_device_info_init function")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is supported, although the offset is different from VG20, so fix
that with a variable and enable getting the product name and serial
number from the FRU. Do this for all SKUs since all SKUs have the FRU
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Aldebaran, the serial may be obtained from the FRU. Only overwrite
the serial with the unique_id if the serial is empty. This will support
printing serial numbers for mGPU devices where there are 2 unique_ids
for the 2 GPUs, but only one serial number for the board
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's supported, so support the unique_id sysfs file
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Having seen at least 1 42-character product_name, bump the number up to
64, and put that definition into amdgpu.h to make future adjustments
simpler.
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The psp bootloader functions code of psp_v13_0.c had been
optimized before. According the code style of psp_v13_0.c
to remove the redundant code of psp_v11_0.c.
v2: squash in drop unused variable (Alex)
Signed-off-by: yipechai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In amdgpu_driver_load_kms, when amdgpu_device_init returns error during driver modprobe, it
will start the error handle path immediately and call into amdgpu_device_unmap_mmio as well
to release mapped VRAM. However, in the following release callback, driver stills visits the
unmapped memory like vcn.inst[i].fw_shared_cpu_addr in vcn_v3_0_sw_fini. So a kernel crash occurs.
[How]
call amdgpu_device_unmap_mmio() if device is unplugged to prevent invalid memory address in
vcn_v3_0_sw_fini() when GPU initialization failure.
Signed-off-by: Leslie Shi <Yuliang.Shi@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* dpu plane state cleanup in prep for multirect
* dpu debugfs cleanup (and moving things to atomic_print_state) in prep
for multirect
* dp support for sc7280
* struct_mutex removal
* include more GMU state in gpu devcore dumps
* add support for a506
* remove old eDP sub-driver (never was used in any upstream supported
devices and modern things with eDP will use DP sub-driver instead)
* debugfs to disable hw gpu hang detect for (igt tests)
* debugfs for dumping display hw state
* and the usual assortment of cleanup and bug fixes
There still seems to be a timing issue with dpu, showing up on sc7180
devices, after the bridge probe-order change. Ie. things work great if
loglevel is high enough (or enough debug options are enabled, etc).
We'll continue to debug this in the new year.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGs+vwr0nkwgYzuYAsCoHtypWpWav+yVvLZGsEJy8tJ56A@mail.gmail.com
[Why]
A porting error on a previous patch left the block of code that
causes the crash from a NULL pointer dereference.
More specifically, we try to access link_enc before it's assigned in
the USB4 case in the following assignment:
config.dio_output_idx = link_enc->transmitter - TRANSMITTER_UNIPHY_A;
[How]
That assignment occurs later depending on the ASIC version. It's only
needed on DCN31 and only after link_enc is already assigned.
Fixes: 986430446c ("drm/amd/display: fix a crash on USB4 over C20 PHY")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll exit optimized power state to do link detection but we won't enter
back into the optimized power state.
This could potentially block s2idle entry depending on the sequencing,
but it also means we're losing some power during the transition period.
[How]
Hook up the handler like DCN21. It was also missed like the
exit_optimized_pwr_state callback.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise SMU won't mark Display as idle when trying to perform s2idle.
[How]
Mark the bit in the dcn31 codepath, doesn't apply to older ASIC.
It needed to be split from phy refclk off to prevent entering s2idle
when PSR was engaged but driver was not ready.
Fixes: 118a331516 ("drm/amd/display: Add DCN3.1 clock manager support")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change of setting a timer callback on boot for 10 seconds is still
working, just lacked power down for DCN10.
[How]
Added power down for DCN10.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
B0 PHY C map to F, D map to G driver use logic instance, dmub does the
remap. Driver still need use the right PHY instance to access right HW.
[how]
use phyical instance when program PHY register.
[note]
could move resync_control programming to dmub next.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some boards(like RX550) seem to have garbage in the upper
16 bits of the vram size register. Check for
this and clamp the size properly. Fixes
boards reporting bogus amounts of vram.
after add this patch,the maximum GPU VRAM size is 64GB,
otherwise only 64GB vram size will be used.
Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A porting error on a previous patch left the block of code that
causes the crash from a NULL pointer dereference.
More specifically, we try to access link_enc before it's assigned in
the USB4 case in the following assignment:
config.dio_output_idx = link_enc->transmitter - TRANSMITTER_UNIPHY_A;
[How]
That assignment occurs later depending on the ASIC version. It's only
needed on DCN31 and only after link_enc is already assigned.
Fixes: 986430446c ("drm/amd/display: fix a crash on USB4 over C20 PHY")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Aldebaran chip passthrough case we need to intimate SMU
about special handling for SBR.On older chips we send
LightSBR to SMU, enabling the same for Aldebaran. Slight
difference, compared to previous chips, is on Aldebaran, SMU
would do a heavy reset on SBR. Hence, the word Heavy
instead of Light SBR is used for SMU to differentiate.
Reviewed by: Shaoyun.liu <Shaoyun.liu@amd.com>
Signed-off-by: sashank saye <sashank.saye@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When an application having open file access to a node forks, its shared
mappings also get reflected in the address space of child process even
though it cannot access them with the object permissions applied. With the
existing permission checks on the gem objects, it might be reasonable to
also create the VMAs with VM_DONTCOPY flag so a user space application
doesn't need to explicitly call the madvise(addr, len, MADV_DONTFORK)
system call to prevent the pages in the mapped range to appear in the
address space of the child process. It also prevents the memory leaks
due to additional reference counts on the mapped BOs in the child
process that prevented freeing the memory in the parent for which we had
worked around earlier in the user space inside the thunk library.
Additionally, we faced this issue when using CRIU to checkpoint restore
an application that had such inherited mappings in the child which
confuse CRIU when it mmaps on restore. Having this flag set for the
render node VMAs helps. VMAs mapped via KFD already take care of this so
this is needed only for the render nodes.
To limit the impact of the change to user space consumers such as OpenGL
etc, limit it to KFD BOs only.
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Yat Sin <david.yatsin@amd.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CP supports unmap queue with reset mode which only destroys specific queue without affecting others.
Replacing whole gpu reset with reset queue mode for RAS poison consumption
saves much time, and we can also fallback to gpu reset solution if reset
queue fails.
v2: Return directly if process is NULL;
Reset queue solution is not applicable to SDMA, fallback to legacy
way;
Call kfd_unref_process after lookup process.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new interface unmaps queues with reset mode for the process consumes
RAS poison, it's only for compute queue.
v2: rename the function to reset_queues.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So we can set reset mode for unmap operation, no functional change.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a reset parameter for umc page retirement, let user decide whether
call gpu reset in umc page retirement.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expand RLCG interface for new GC read & write commands.
New interface will only be used if the PF enables the flag in pf2vf msg.
v2: Added a description for the scratch registers
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: David Nieto <david.nieto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver needs to call get_xgmi_info() before ip_init
to determine whether it needs to handle a pending hive reset.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: David Nieto <david.nieto@amd.com>
Reviewed by: shaoyun.liu <Shaoyun.lui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Modify GC register access from MMIO to RLCG if the indirect
flag is set
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: David Nieto <david.nieto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Modify GC register access from MMIO to RLCG if the
indirect flag is set
v2: Replaced ternary operator with if-else for better
readability
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: David Nieto <david.nieto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add helper macros to change register access
from direct to indirect.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: David Nieto <david.nieto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Recently, there is security policy update under SRIOV.
We need to filter the registers that hit the violation
and move the code to the host driver side so that
the guest driver can execute correctly.
Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chips with no display hardware should return false for
DC support.
v2: drop Arcturus and Aldebaran
Fixes: f7f12b2582 ("drm/amdgpu: default to true in amdgpu_device_asic_has_dc_support")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reported-by: Tareque Md.Hanif <tarequemd.hanif@yahoo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By setting mp1_state as PP_MP1_STATE_UNLOAD, MP1 will do some proper cleanups and
put itself into a state ready for PNP. That can workaround some random resuming
failure observed on BOCO capable platforms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the platform suspend happens to fail and the power rail
is not turned off, the GPU will be in an unknown state on
resume, so reset the asic so that it will be in a known
good state on resume even if the platform suspend failed.
v2: handle s0ix
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the s0ix entry need retain gfx in the gfxoff state,so here need't
set gfx cgpg in the S0ix suspend-resume process. Moreover move the S0ix
check into SMU12 can simplify the code condition check.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1712
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We mustn't forget to update our FBC state even if we don't have
to reallocate the CFB. Otherwise we won't refresh our notion
of what eg. the new fence or the new override CFB stride
should be. Using the wrong CFB stride in particular can cause
underruns and could even corrupt other stuff in stolen.
Fixes: f4cfdbb02c ("drm/i915/fbc: Nuke state_cache")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4774
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216110822.8461-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit 798c5daf3c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Increment composite fence seqno on each fence creation.
Fixes: 544460c338 ("drm/i915: Multi-BB execbuf")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214195913.35735-1-matthew.brost@intel.com
(cherry picked from commit 62eeb9ae13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
'prev_engine' was declared inside the output loop and checked in the
inner after at least 1 pass of either loop. The variable should be
declared outside both loops as it needs to be persistent across the
entire loop structure.
Fixes: e5e32171a2 ("drm/i915/guc: Connect UAPI to GuC multi-lrc interface")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211219001909.24348-1-matthew.brost@intel.com
(cherry picked from commit cbffbac9c1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
* bridge/lvds: Fix DT bindings
* vmwgfx: Fix several issues with the recent conversion to GEM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmHEP1sACgkQaA3BHVML
eiOgnQgAmjsV2Y21demsRAgdAFdQa4QgNClnDUOPZpwfoWpaV9lXl4eh0h2z7Jv8
Akh/s219AoGUAuvJ050tCp3w7H0b9qGSwCohyUa7BLQCcA+Ecd3/2ogD12vbQLMU
WHfPD1a7r5UHaj7X9vtm8kAU/SrbAxtdL+JHPHBqbbeG0PyiU7tWYqC5JoLL81+D
EjYhMxtxdv0WbkgOE4K+cMnYZTq3FVhYHSXUOWaP/nwH9w/l+tDjCYwKPV9bKYYW
XL71PHg0k/3YKPo/iPqh7hmLY+NXDDN7wioTvrk60cBUIeH8YgHpDJEXaFxmEYrs
fiLfJBo706zS/gsZGAP3XqYY7spU5A==
=uWo8
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2021-12-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* bridge/lvds: Fix DT bindings
* vmwgfx: Fix several issues with the recent conversion to GEM
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YcRAH8lYbsoSCeY9@linux-uq9g.fritz.box
Driver Changes:
- Added bits of DG2 support around page table handling (Stuart Summers, Matthew Auld)
- Fixed wakeref leak in PMU busyness during reset in GuC mode (Umesh Nerlige Ramappa)
- Fixed debugfs access crash if GuC failed to load (John Harrison)
- Bring back GuC error log to error capture, undoing accidental earlier breakage (Thomas Hellström)
- Fixed memory leak in error capture caused by earlier refactoring (Thomas Hellström)
- Exclude reserved stolen from driver use (Chris Wilson)
- Add memory region sanity checking and optional full test (Chris Wilson)
- Fixed buffer size truncation in TTM shmemfs backend (Robert Beckett)
- Use correct lock and don't overwrite internal data structures when stealing GuC context ids (Matthew Brost)
- Don't hog IRQs when destroying GuC contexts (John Harrison)
- Make GuC to Host communication more robust (Matthew Brost)
- Continuation of locking refactoring around VMA and backing store handling (Maarten Lankhorst)
- Improve performance of reading GuC log from debugfs (John Harrison)
- Log when GuC fails to reset an engine (John Harrison)
- Speed up GuC/HuC firmware loading by requesting RP0 (Vinay Belgaumkar)
- Further work on asynchronous VMA unbinding (Thomas Hellström, Christian König)
- Refactor GuC/HuC firmware handling to prepare for future platforms (John Harrison)
- Prepare for future different GuC/HuC firmware signing key sizes (Daniele Ceraolo Spurio, Michal Wajdeczko)
- Add noreclaim annotations (Matthew Auld)
- Remove racey GEM_BUG_ON between GPU reset and GuC communication handling (Matthew Brost)
- Refactor i915->gt with to_gt(i915) to prepare for future platforms (Michał Winiarski, Andi Shyti)
- Increase GuC log size for CONFIG_DEBUG_GEM (John Harrison)
- Fixed engine busyness in selftests when in GuC mode (Umesh Nerlige Ramappa)
- Make engine parking work with PREEMPT_RT (Sebastian Andrzej Siewior)
- Replace X86_FEATURE_PAT with pat_enabled() (Lucas De Marchi)
- Selftest for stealing of guc ids (Matthew Brost)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YcRvKO5cyPvIxVCi@tursulin-mobl2
Some GPU heavy test programs manage to trigger the hangcheck quite often.
If there are no other GPU users in the system and the test program
exhibits a very regular structure in the commandstreams that are being
submitted, we can end up with two distinct submits managing to trigger
the hangcheck with the FE in a very similar address range. This leads
the hangcheck to believe that the GPU is stuck, while in reality the GPU
is already busy working on a different job. To avoid those spurious
GPU resets, also remember and consider the last completed fence seqno
in the hang check.
Reported-by: Joerg Albert <joerg.albert@iav.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Convert free_work into delayed_work, similar to ttm to allow converting the
blocking lock in __i915_gem_free_objects to a trylock.
Unlike ttm, the object should already be idle, as it's kept alive
by a reference through struct i915_vma->active, which is dropped
after all vma's are idle.
Because of this, we can use a no wait by default, or when the lock
is contested, we use ttm's 10 ms.
The trylock should only fail when the object is sharing it's resv with
other objects, and typically objects are not kept locked for a long
time, so we can safely retry on failure.
Fixes: be7612fd66 ("drm/i915: Require object lock when freeing pages during destruction")
Testcase: igt/gem_exec_alignment/pi*
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211222155622.2960379-1-maarten.lankhorst@linux.intel.com
It's not only supported by HG/PX laptops. It's supported
by all dGPUs which supports BOCO/BACO functionality (runtime
D3).
BOCO - Bus Off, Chip Off. The entire chip is powered off.
This is controlled by ACPI.
BACO - Bus Active, Chip Off. The chip still shows up
on the PCI bus, but the device itself is powered
down.
v2: fix missed HG/PX reference
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Replacing lagacy gpio interface of dsi driver with gpiod one.
- Implementing a generic GEM object mmap and use it instead of
exynos specific one.
- Dropping the use of label from dsi driver. Which also fixes
a build warning.
- Just trivial cleanup by dropping unnecessay code.
-----BEGIN PGP SIGNATURE-----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=Fgtp
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-next-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Four cleanups
- Replacing lagacy gpio interface of dsi driver with gpiod one.
- Implementing a generic GEM object mmap and use it instead of
exynos specific one.
- Dropping the use of label from dsi driver. Which also fixes
a build warning.
- Just trivial cleanup by dropping unnecessay code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211222035345.26595-1-inki.dae@samsung.com
This contains a fairly large rework that makes the buffer objects behave
more according to what the DMA-BUF infrastructure expects. A buffer
object cache is implemented on top of that to make certain operations
such as page-flipping more efficient by avoiding needless map/unmap
operations. This in turn is useful to implement asynchronous commits to
support legacy cursor updates.
Another fairly big addition is the NVDEC driver. This uses the updated
UABI introduced in v5.15-rc1 to provide access to the video decode
engines found on Tegra210 and later.
This also includes some power management improvements that are useful on
older devices in particular because they, together with a bunch of other
changes across the kernel, allow the system to scale down frequency and
voltages when mostly idle and prevent these devices from becoming
excessively hot.
The remainder of these changes is an assortment of cleanups and minor
fixes.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmG8nFoTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYhcEAC7MOuQHeNxG99+23nwtkdm1/pgsPXj
Nw8G87Q+AtnePykMaqmtxtxfXti3Vq8qL+bIgOzodXAPVYuqICOwU8MCukuPXn4X
OSfKzKKMKrqbzCpBVoAq1YfJX5QOv8BYNMzxCx7TVb0TGIT5cS5gEEjSUg9d4l37
qQnQRkO+/04yvKMN0UhMz4BwJG8xYxqAFa4byd3ZhQ5DZvb8wz/iEpUU3YbSTKuC
Ri0rUVKDJxhJIfZ/HkFLDw1lKhg3JpjM5Qz+Uly/OUSLVFNeHkaL0m/LqqWr1+ug
GIrkRtE+kvdezMFHtffdAL6xBbACHjkuiT4TN8OJuXO+o9TqJZyvLckV/DW/pdfY
UmVsu0ph9SpbTcUOUFJPpIN7/8cR+AiUo9TfUkNFsn+vO02Hmg8ZwMWucPdUTusj
/apVKz0vbs1xDQ9fV6tTtn+9o5UtO0kMJsWLm9v7je/odguo0hWoyf+aMNpstoXy
qZ0PLC0Ltky+5re4X4iwGjoOBQpNyYsl5Vcal0pSu+W5JxVAaB4q3UN/Y5pHopRP
YZFN/s5Tx1bfR2eySVnW72bm9N1elLUgYZQwx41eguRDdZaFo7EaPBS49AT6BD8X
COMvB8Sbb5r4wZQL2RVom3dhPEhhuSfGXszxcLf1O6oEyZXtSL1EnZiJkhC440Va
umD6K8ynnXHnzA==
=y3U1
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.17-rc1' of https://gitlab.freedesktop.org/drm/tegra into drm-next
drm/tegra: Changes for v5.17-rc1
This contains a fairly large rework that makes the buffer objects behave
more according to what the DMA-BUF infrastructure expects. A buffer
object cache is implemented on top of that to make certain operations
such as page-flipping more efficient by avoiding needless map/unmap
operations. This in turn is useful to implement asynchronous commits to
support legacy cursor updates.
Another fairly big addition is the NVDEC driver. This uses the updated
UABI introduced in v5.15-rc1 to provide access to the video decode
engines found on Tegra210 and later.
This also includes some power management improvements that are useful on
older devices in particular because they, together with a bunch of other
changes across the kernel, allow the system to scale down frequency and
voltages when mostly idle and prevent these devices from becoming
excessively hot.
The remainder of these changes is an assortment of cleanups and minor
fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211217142912.558095-1-thierry.reding@gmail.com
AMD systems currently lay out MCA bank types such that the type of bank
number "i" is either the same across all CPUs or is Reserved/Read-as-Zero.
For example:
Bank # | CPUx | CPUy
0 LS LS
1 RAZ UMC
2 CS CS
3 SMU RAZ
Future AMD systems will lay out MCA bank types such that the type of
bank number "i" may be different across CPUs.
For example:
Bank # | CPUx | CPUy
0 LS LS
1 RAZ UMC
2 CS NBIO
3 SMU RAZ
Change the structures that cache MCA bank types to be per-CPU and update
smca_get_bank_type() to handle this change.
Move some SMCA-specific structures to amd.c from mce.h, since they no
longer need to be global.
Break out the "count" for bank types from struct smca_hwid, since this
should provide a per-CPU count rather than a system-wide count.
Apply the "const" qualifier to the struct smca_hwid_mcatypes array. The
values in this array should not change at runtime.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211216162905.4132657-3-yazen.ghannam@amd.com
Protect updates of struct i915_vma flags and async binding / unbinding
with the vm::mutex. This means that i915_vma_bind() needs to assert
vm::mutex held. In order to make that possible drop the caching of
kmap_atomic() maps around i915_vma_bind().
An alternative would be to use kmap_local() but since we block cpu
unplugging during sleeps inside kmap_local() sections this may have
unwanted side-effects. Particularly since we might wait for gpu while
holding the vm mutex.
This change may theoretically increase execbuf cpu-usage on snb, but
at least on non-highmem systems that increase should be very small.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211221200050.436316-5-thomas.hellstrom@linux.intel.com
First of all as discussed multiple times now kernel copies *must* always
wait for all fences in a BO before actually doing the copy. This is
mandatory.
Additional to that drop the handling when there can't be a shared slot
allocated on the source BO and just properly return an error code.
Otherwise this code path would only be tested under out of memory
conditions.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211221200050.436316-3-thomas.hellstrom@linux.intel.com
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Since the gt migration code was using only a single fence for
dependencies, these were collected in a dma_fence_array. However, it
turns out that it's illegal to use some dma_fences in a dma_fence_array,
in particular other dma_fence_arrays and dma_fence_chains, and this
causes trouble for us moving forward.
Have the gt migration code instead take a const struct i915_deps for
dependencies. This means we can skip the dma_fence_array creation
and instead pass the struct i915_deps instead to circumvent the
problem.
v2:
- Make the prev_deps() function static. (kernel test robot <lkp@intel.com>)
- Update the struct i915_deps kerneldoc.
v4:
- Rebase.
Fixes: 5652df829b ("drm/i915/ttm: Update i915_gem_obj_copy_ttm() to be asynchronous")
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211221200050.436316-2-thomas.hellstrom@linux.intel.com
Dropped the use of 'out' label from exynos_dsi_register_te_irq function
because the label isn't needed. This patch returns an error in each
error case directly not going to 'out' label.
With this patch build warning[1] is also fixed, which was reported by
kernel test robot <lkp@intel.com>
[1] https://www.spinics.net/lists/dri-devel/msg323803.html
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Moving the driver-specific mmap code into a GEM object function allows
for using DRM helpers for various mmap callbacks.
The respective exynos functions are being removed. The file_operations
structure exynos_drm_driver_fops is now being created by the helper macro
DEFINE_DRM_GEM_FOPS().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixed merge conflict.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Considering the current transition of the GPIO subsystem, remove all
dependencies of the legacy GPIO interface (linux/gpio.h and linux
/of_gpio.h) and replace it with the descriptor-based GPIO approach.
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
By default, GT (and GuC) run at RPn. Requesting for RP0
before firmware load can speed up DMA and HuC auth as well.
In addition to writing to 0xA008, we also need to enable
swreq in 0xA024 so that Punit will pay heed to our request.
SLPC will restore the frequency back to RPn after initialization,
but we need to manually do that for the non-SLPC path.
We don't need a manual override in the SLPC disabled case, just
use the intel_rps_set function to ensure consistent RPS state.
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Sujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216233022.21351-1-vinay.belgaumkar@intel.com
Always waiting for the exclusive fence resulted on some performance
regressions. So try to wait for the shared fences first, then the
exclusive fence should always be signaled already.
v2: fix incorrectly placed "(", add some comment why we do this.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Stefan Fritsch <sf@sfritsch.de>
Tested-by: Dan Moulding <dmoulding@me.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211209102335.18321-1-christian.koenig@amd.com
If GuC encounters an error during engine reset, the i915 driver
promotes to full GT reset. This includes an info message about why the
reset is happening. However, that is not treated as a failure by any
of the CI systems because resets are an expected occurrance during
testing. This kind of failure is a major problem and should never
happen. So, complain more loudly and make sure CI notices.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-4-John.C.Harrison@Intel.com
Lots of testing is done with the DEBUG_GEM config option enabled but
not the DEBUG_GUC option. That means we only get teeny-tiny GuC logs
which are not hugely useful. Enabling full DEBUG_GUC also spews lots
of other detailed output that is not generally desired. However,
bigger GuC logs are extremely useful for almost any regression debug.
So enable bigger logs for DEBUG_GEM builds as well.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-3-John.C.Harrison@Intel.com
Add support for telling the debugfs interface the size of the GuC log
dump in advance. Without that, the underlying framework keeps calling
the 'show' function with larger and larger buffer allocations until it
fits. That means reading the log from graphics memory many times - 16
times with the full 18MB log size.
v2: Don't return error codes from size query. Report overflow in the
error dump as well (review feedback from Daniele).
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-2-John.C.Harrison@Intel.com
Currently we allow rediculous amounts of kernel memory being allocated
via the etnaviv GEM_SUBMIT ioctl, which is a pretty easy DoS vector. Put
some reasonable limits in to fix this.
The commandstream size is limited to 64KB, which was already a soft limit
on older kernels after which the kernel only took submits on a best effort
base, so there is no userspace that tries to submit commandstreams larger
than this. Even if the whole commandstream is a single incrementing address
load, the size limit also limits the number of potential relocs and
referenced buffers to slightly under 64K, so use the same limit for those
arguments. The performance monitoring infrastructure currently supports
less than 50 performance counter signals, so limiting them to 128 on a
single submit seems like a reasonably future-proof number for now. This
number can be bumped if needed without breaking the interface.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Now that we require locking to evict, multiple vmas from the same object
might not be evicted. This is expected and required, because execbuf will
move to short-term pinning by using the lock only. This will cause these
tests to fail, because they create a ton of vma's for the same object.
Unbind manually to prevent spurious -ENOSPC in those mock tests.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-8-maarten.lankhorst@linux.intel.com
In the next commits, we may not evict when refcount = 0.
igt_vm_isolation() continuously tries to pin/unpin at same address,
but also calls put() on the object, which means the object may not
be unpinned in time.
Instead of this, re-use the same object over and over, so they can
be unbound as required.
Changes since v1:
- Fix cleaning up obj_b on failure. (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-7-maarten.lankhorst@linux.intel.com
We will need the lock to unbind the vma, and wait for bind to complete.
Remove the special casing for the !ww path, and force ww locking for all.
Changes since v1:
- Pass err to for_i915_gem_ww handling for -EDEADLK handling.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-6-maarten.lankhorst@linux.intel.com
Big delta, but boils down to moving set_pages to i915_vma.c, and removing
the special handling, all callers use the defaults anyway. We only remap
in ggtt, so default case will fall through.
Because we still don't require locking in i915_vma_unpin(), handle this by
using xchg in get_pages(), as it's locked with obj->mutex, and cmpxchg in
unpin, which only fails if we race a against a new pin.
Changes since v1:
- aliasing gtt sets ZERO_SIZE_PTR, not -ENODEV, remove special case
from __i915_vma_get_pages(). (Matt)
Changes since v2:
- Free correct old pages in __i915_vma_get_pages(). (Matt)
Remove race of clearing vma->pages accidentally from put,
free it but leave it set, as only get has the lock.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-4-maarten.lankhorst@linux.intel.com
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Call drop_pages with the gem object lock held, instead of the other
way around. This will allow us to drop the vma bindings with the
gem object lock held.
We plan to require the object lock for unpinning in the future,
and this is an easy target.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-3-maarten.lankhorst@linux.intel.com
When reworking the code to move the eviction fence to the object,
the best code is removed code.
Remove some functions that are unused, and change the function definition
if it's only used in 1 place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
[mlankhorst: Remove new use of i915_active_has_exclusive]
Link: https://patchwork.freedesktop.org/patch/msgid/20211216142749.1966107-2-maarten.lankhorst@linux.intel.com
Previously assigned whole guc_id structure (list, spin lock) which is
incorrect, only assign the guc_id.id.
Fixes: 0f7976506d ("drm/i915/guc: Rework and simplify locking")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214170500.28569-3-matthew.brost@intel.com
(cherry picked from commit 939d8e9c87)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
s/ce/cn/ when grabbing guc_state.lock before calling
clr_context_registered.
Fixes: 0f7976506d ("drm/i915/guc: Rework and simplify locking")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214170500.28569-2-matthew.brost@intel.com
(cherry picked from commit b25db8c782)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In preparation of the multitile support, highlight the root GT by
calling it gt0 inside the drm i915 private data.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-11-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-10-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-9-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-8-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-7-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-6-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-5-andi.shyti@linux.intel.com
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-4-andi.shyti@linux.intel.com
To allow further refactoring and abstract away the fact that GT is
stored inside i915 private.
No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-3-andi.shyti@linux.intel.com
We now support a per-gt uncore, yet we're not able to infer which GT
we're operating upon. Let's store a backpointer for now.
At this point the early initialization of the gt needs to be
broken in two parts where the first is needed to assign to the gt
the i915 private data pointer and the uncore. A temporary
function has been made and the two parts are
__intel_gt_init_early() and intel_gt_init_early(). This split
will be fixed in the future with the multitile patch.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-2-andi.shyti@linux.intel.com
A CP_PROTECT entry for SMMU registers is missing for A540. According to
downstream sources its length is same as on A530 - 0x20000 bytes.
On all other revisions SMMU region length is 0x10000 bytes. Despite
this, we setup region of length 0x20000 on all revisions. This doesn't
cause any issues on those GPUs. As for preventing accesses to the region
from protected mode it was tested to work the same.
This patch drops the "if" condition in setup of CP_PROTECT entry because
it already includes all supported revisions except A540.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Link: https://lore.kernel.org/r/20211212160333.980343-2-vladimir.lypak@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Play a video on the raven (or PCO, raven2) platform, and then do the S3
test. When resume, the following error will be reported:
amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring
vcn_dec test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block
<vcn_v1_0> failed -110
amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
[why]
When playing the video: The power state flag of the vcn block is set to
POWER_STATE_ON.
When doing suspend: There is no change to the power state flag of the
vcn block, it is still POWER_STATE_ON.
When doing resume: Need to open the power gate of the vcn block and set
the power state flag of the VCN block to POWER_STATE_ON.
But at this time, the power state flag of the vcn block is already
POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm:
avoid duplicate powergate/ungate setting" patch will return the
amdgpu_dpm_set_powergating_by_smu function directly.
As a result, the gate of the power was not opened, causing the
subsequent ring test to fail.
[how]
In the suspend function of the vcn block, explicitly change the power
state flag of the vcn block to POWER_STATE_OFF.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix the message argument.
0: Allow power down
1: Disallow power down
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
vmw_user_bo_lookup can fail to lookup user buffers, especially because
the buffer handles come from the userspace. The return value has
to be checked before the buffers are put back.
This was spotted by Dan's Smatch statick checker:
drivers/gpu/drm/vmwgfx/vmwgfx_bo.c:574 vmw_user_bo_synccpu_release()
error: uninitialized symbol 'vmw_bo'.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215200224.3693345-1-zack@kde.org
(cherry picked from commit 60c9ecd705)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Before the driver had screen targets support we had to disable explicit
bringup of its infrastructure because it was breaking screen objects
support.
Since the implementation of screen targets landed there hasn't been a
reason to explicitly disable it and the options were never used.
Remove of all that unused code.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: d80efd5cb3 ("drm/vmwgfx: Initial DX support")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-3-zack@kde.org
(cherry picked from commit 11343099d5)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Old versions of the svga device used to export virtual vram, handling of
which was optimized on top of transparent hugepages support. Only very
old devices (OpenGL 2.1 support and earlier) used this code and at this
point performance differences are negligible.
Because the code requires very old hardware versions to run it has
been largely untested and unused for a long time.
Furthermore removal of the ttm hugepages support in:
commit 0d97950953 ("drm/ttm: remove ttm_bo_vm_insert_huge()")
broke the coherency mode in vmwgfx when running with hugepages.
Fixes: 0d97950953 ("drm/ttm: remove ttm_bo_vm_insert_huge()")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-2-zack@kde.org
(cherry picked from commit 49d535d64d)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
On i386 size_t is of course 32bits and using long int throws warnings,
trivially fix it by using the dedicated size_t format.
This is enough to fix the following warning found by the kernel test
robot:
drivers/gpu/drm/vmwgfx/vmwgfx_gem.c: In function 'vmw_bo_print_info':
>> drivers/gpu/drm/vmwgfx/vmwgfx_gem.c:230:33: warning: format '%ld'
expects argument of type 'long int', but argument 4 has type 'size_t'
{aka 'unsigned int'} [-Wformat=]
230 | seq_printf(m, "\t\t0x%08x: %12ld bytes %s, type = %s",
| ~~~~^
| |
| long int
| %12d
231 | id, bo->base.base.size, placement, type);
| ~~~~~~~~~~~~~~~~~~
| |
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-1-zack@kde.org
(cherry picked from commit 72345114c9)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
1. Add support for MT8192
2. CMDQ refinement.
3. Miscellaneous clean up and reorder.
4. Set the default value of rotation to DRM_MODE_ROTATE_0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2VjD
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.17' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.16
1. Add support for MT8192
2. CMDQ refinement.
3. Miscellaneous clean up and reorder.
4. Set the default value of rotation to DRM_MODE_ROTATE_0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1639700370-3541-1-git-send-email-chunkuang.hu@kernel.org
The display driver wants to pass a custom flag to the DMA engine driver,
which it started doing by using the slave_id field that was traditionally
used for a different purpose.
As there is no longer a correct use for the slave_id field, it should
really be removed, and the remaining users changed over to something
different.
The new mechanism for passing nonstandard settings is using the
.peripheral_config field, so use that to pass a newly defined structure
here, making it clear that this will not work in portable drivers.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-10-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drm/i915 feature pull #2 for v5.17:
Features and functionality:
- Add eDP privacy screen support (Hans)
- Add Raptor Lake S (RPL-S) support (Anusha)
- Add CD clock squashing support (Mika)
- Properly support ADL-P without force probe (Clint)
- Enable pipe color support (10 bit gamma) for display 13 platforms (Uma)
- Update ADL-P DMC firmware to v2.14 (Madhumitha)
Refactoring and cleanups:
- More FBC refactoring preparing for multiple FBC instances (Ville)
- Plane register cleanups (Ville)
- Header refactoring and include cleanups (Jani)
- Crtc helper and vblank wait function cleanups (Jani, Ville)
- Move pipe/transcoder/abox masks under intel_device_info.display (Ville)
Fixes:
- Add a delay to let eDP source OUI write take effect (Lyude)
- Use div32 version of MPLLB word clock for UHBR on SNPS PHY (Jani)
- Fix DMC firmware loader overflow check (Harshit Mogalapalli)
- Fully disable FBC on FIFO underruns (Ville)
- Disable FBC with double wide pipe as mutually exclusive (Ville)
- DG2 workarounds (Matt)
- Non-x86 build fixes (Siva)
- Fix HDR plane max width for NV12 (Vidya)
- Disable IRQ for selftest timestamp calculation (Anshuman)
- ADL-P VBT DDC pin mapping fix (Tejas)
Merges:
- Backmerge drm-next for privacy screen plumbing (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87ee6f5h9u.fsf@intel.com
simpledrm and a user-space regression revert for fb-helper
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYbr2+QAKCRDj7w1vZxhR
xaI/AQDw8wCws8TXFMiU/5RHkYPVRXN1NSzHt8C/Pf44Yu6ZWwEAiuzP1OpnNyxP
WmQIC4vJ0NX4s63enEgQJ8gVznYkOwk=
=fTbn
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2021-12-16-1' of ssh://git.freedesktop.org/git/drm/drm-misc into drm-fixes
One null pointer dereference fix for ast, a pixel clock unit fix for
simpledrm and a user-space regression revert for fb-helper
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216082603.pm6yzlckmxvwnqyv@houat
Used on gfx9 based systems. Fixes incorrect CU counts reported
in the kernel log.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1833
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some old registers leftover from pre-silicon. No longer
relevant on real hardware. Remove.
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want to be able to call virt data exchange conditionally
after gmc sw init to reserve bad pages as early as possible.
Since this is a conditional call, we will need
to call it again unconditionally later in the init sequence.
Refactor the data exchange function so it can be
called multiple times without re-initializing the work item.
v2: Cleaned up the code. Kept the original call to init_exchange_data()
inside early init to initialize the work item, afterwards call
exchange_data() when needed.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed By: Shaoyun.liu <Shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use max() and min() in order to make code cleaner.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Play a video on the raven (or PCO, raven2) platform, and then do the S3
test. When resume, the following error will be reported:
amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring
vcn_dec test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block
<vcn_v1_0> failed -110
amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110
[why]
When playing the video: The power state flag of the vcn block is set to
POWER_STATE_ON.
When doing suspend: There is no change to the power state flag of the
vcn block, it is still POWER_STATE_ON.
When doing resume: Need to open the power gate of the vcn block and set
the power state flag of the VCN block to POWER_STATE_ON.
But at this time, the power state flag of the vcn block is already
POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm:
avoid duplicate powergate/ungate setting" patch will return the
amdgpu_dpm_set_powergating_by_smu function directly.
As a result, the gate of the power was not opened, causing the
subsequent ring test to fail.
[how]
In the suspend function of the vcn block, explicitly change the power
state flag of the vcn block to POWER_STATE_OFF.
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828
Signed-off-by: chen gong <curry.gong@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
