Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some irqs which are applicable for sdm845 target are no
longer applicable for sc7180 and sc7280 targets. Add a
flag to indicate the irqs which are obsolete for a
particular target so that these irqs are skipped while
checking for matching irq lookup index.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617688895-26275-4-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently, each register in the dpu interrupt set is allowed
to have a maximum of 32 interrupts. With the introduction
of INTF_5_VSYNC and INTF_5_UNDERRUN irqs for EDP panel,
the total number of interrupts under INTR_STATUS register
in dpu_irq_map will exceed 32. Increase the range of each
interrupt register to 64 to handle this.
This patch has dependency on the below series:
https://patchwork.kernel.org/project/linux-arm-msm/list/?series=461193
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617688895-26275-2-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The reset value of INTF_CONFIG2 register is changed
for SC7280 family. Changes are added to program
this register correctly based on the target.
DATA_HCTL_EN in INTF_CONFIG2 register allows data
to be transferred at a different rate than video
timing. When this is set, the number of data per
line follows DISPLAY_DATA_HCTL register value.
This change adds support to program these
registers for sc7280 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617685792-14376-5-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
A new register called CTL_FETCH_ACTIVE is introduced in
SC7280 family which is used to inform the HW about
the pipes which are active in the current ctl path.
This change adds support to program this register
based on the active pipes in the current composition.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617685792-14376-4-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Interface block offsets are different for SC7280 family
when compared to existing targets. These offset values
are used to access the interface irq registers. This
change adds proper interface offsets for SC7280 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1617685792-14376-3-git-send-email-mkrishn@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that tracking is wired up for potentially evictable GEM objects,
wire up shrinker and the remaining GEM bits for unpinning backing pages
of inactive objects.
Disabled by default for now, with an 'enable_eviction' module param to
enable so that we can get some more testing on the range of generations
(and iommu pairings) supported.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-9-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Shoot down any mmap's *first* before put_pages(). Also add a WARN_ON
that the object is locked (to make it clear that this doesn't race with
msm_gem_fault()) and remove a redundant WARN_ON (since is_purgable()
already covers that case).
Fixes: 68209390f1 ("drm/msm: shrinker support")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-8-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Objects that are potential for swapping out are (1) willneed (ie. if
they are purgable/MADV_WONTNEED we can just free the pages without them
having to land in swap), (2) not on an active list, (3) not dma-buf
imported or exported, and (4) not vmap'd. This repurposes the purged
list for objects that do not have backing pages (either because they
have not been pinned for the first time yet, or in a later patch because
they have been unpinned/evicted.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-7-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently nearly everything, other than newly allocated objects which
are not yet backed by pages, is pinned and resident in RAM. But it will
be nice to have some stats on what is unpinned once that is supported.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-6-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently these always go together, either when we purge MADV_WONTNEED
objects or when the object is freed. But for unpin, we want to be able
to purge (unmap from iommu) the vma, while keeping the iova range
allocated (so we can remap back to the same GPU virtual address when the
object is re-pinned.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-5-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently this doesn't matter since we keep the pages pinned until the
object is destroyed. But when we start unpinning pages to allow objects
to be evicted to swap, it will.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
So we don't have to duplicate the boilerplate for eviction.
This also lets us re-use the main scan loop for vmap shrinker.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
If you mess something up, you don't really need to see the same warn on
splat 4000 times pumped out a slow debug UART port..
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210405174532.1441497-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently DPU driver scales bandwidth and core clock for sc7180 only,
while the rest of chips get static bandwidth votes. Make all chipsets
scale bandwidth and clock per composition requirements like sc7180 does.
Drop old voting path completely.
Tested on RB3 (SDM845) and RB5 (SM8250).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210401020533.3956787-2-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fill clk_inefficiency_factor, bw_inefficiency_factor and
min_prefill_lines in hw catalog data for sdm845 and sm8[12]50.
Efficiency factors are blindly copied from sc7180 data, while
min_prefill_lines is based on downstream display driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210401020533.3956787-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
SM8250 platform has a 8-Levels VIG QoS setting. This setting was missed
due to bad interaction with b8dab65b5a ("drm/msm/dpu: Move
DPU_SSPP_QOS_8LVL bit to SDM845 and SC7180 masks"), which was applied in
parallel.
Fixes: d21fc5dfc3 ("drm/msm/dpu1: add support for qseed3lite used on sm8250")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210318105435.2011222-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-25-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The src_truthtable config is not used for some of phys, which use other
means of configuring the master/slave usecases. Inline this function
with the goal of removing src_pll_id argument in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-24-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The 7nm, 10nm and 14nm drivers would store interim data used during
VCO/PLL rate setting in the global dsi_pll_Nnm structure. Move this data
structures to the onstack storage. While we are at it, drop
unused/static 'config' data, unused config fields, etc.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-23-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop duplicate fields pdev and id from dsi_pll_Nnm instances. Reuse
those fields from the provided msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-22-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All PHY drivers would map dsi_pll area. Some PHY drivers would also
map dsi_phy area again (a leftover from old PHY/PLL separation). Move
all ioremaps to the common dsi_phy driver code and drop individual
ioremapped areas from PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-21-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the struct msm_dsi_pll abstraction, by including vco's clk_hw
directly into struct msm_dsi_phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-19-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make save_state/restore callbacks accept struct msm_dsi_phy rather than
struct msm_dsi_pll. This moves them to struct msm_dsi_phy_ops, allowing
us to drop struct msm_dsi_pll_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-18-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
10nm and 7nm already do not use these helpers, as they handle setting
slave DSI clocks after enabling VCO. Modify the rest of PHY drivers to
remove unnecessary indirection and drop enable_seq/disable_seq PLL
callbacks.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-17-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of setting the variable and then using it just in the one place,
determine vco_delay directly at the PLL configuration time.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-16-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
These drivers do not use vco_delay variable, so drop it from all of
them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-15-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Morph msm_dsi_pll_save/restore_state() into msm_dsi_phy_save/restore_state(),
thus removing last bits of knowledge about msm_dsi_pll from dsi_manager.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-14-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devm_of_clk_add_hw_provider() to register provided clocks. This
allows dropping the remove function alltogether.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-13-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devres-enabled version of clock registration functions. This lets us
remove dsi_pll destroy callbacks completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-12-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_dsi_pll_set_usecase() function is not used outside of individual DSI
PHY drivers, so drop it in favour of calling the the respective
set_usecase functions directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-10-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
With the current upstream driver the msm_dsi_phy_type enum does not make
much sense: all DSI PHYs are probed using the dt bindings, the phy type
is not passed between drivers. Use quirks in phy individual PHY drivers
to differentiate minor harware differences and drop the enum.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-8-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all PLL-related callbacks into struct msm_dsi_phy_cfg. This limits
the amount of data in the struct msm_dsi_pll.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-7-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only PLL using multiple enable sequences is the 28nm PLL, which just
does the single step in the loop. Push that support back into the PLL
code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-6-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Each phy version is tightly coupled with the corresponding PLL code,
there is no need to keep them separate. Fuse source files together in
order to simplify DSI code.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-5-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
DSI PHY init callback would either map dsi_phy_regulator or dsi_phy_lane
depending on the PHY type. Replace those callbacks with configuration
options governing mapping those regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the error checking logic in the dp_debug module could
pass zero to PTR_ERR and it causes the below kbot warnings:
drivers/gpu/drm/msm/dp/dp_debug.c:378 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:387 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:396 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:405 dp_debug_init()
warn: passing zero to 'PTR_ERR'
Debugfs functions are not supposed to be checked in the normal
case so delete this code. Also it silences the above Smatch
warnings that we're checking for NULL when these functions only
return error pointers.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1614971839-2686-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix an incorrect NULL check reported by kbot in the MSM DP driver
smatch warnings:
drivers/gpu/drm/msm/dp/dp_hpd.c:37 dp_hpd_connect()
error: we previously assumed 'hpd_priv->dp_cb' could be null
(see line 37)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1614971839-2686-2-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix a couple of indentation warnings reported by
kbot across MSM DP driver:
New smatch warnings:
drivers/gpu/drm/msm/dp/dp_debug.c:229 dp_test_data_show()
warn: inconsistent indenting
drivers/gpu/drm/msm/dp/dp_power.c:203 dp_power_clk_enable()
warn: inconsistent indenting
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1614971839-2686-1-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM8996 core_mmss clock was commented out due to some
strange issues that others were experiencing.
At least SONY Tone family is working perfectly fine with this clock
declared and gets it up and running without any error.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228124328.136397-1-konrad.dybcio@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Set the flag vblank_disable_immediate = true to turn off vblank irqs
immediately as soon as drm_vblank_put is requested so that there are
no irqs triggered during idle state. This will reduce cpu wakeups
and help in power saving.
To enable vblank_disable_immediate flag the underlying KMS driver
needs to support high precision vblank timestamping and also a
reliable way of providing vblank counter which is incrementing
at the leading edge of vblank.
This patch also brings in changes to support vblank_disable_immediate
requirement in dpu driver.
Changes in v1:
- Specify reason to add vblank timestamp support. (Rob).
- Add changes to provide vblank counter from dpu driver.
Changes in v2:
- Fix warn stack reported by Rob Clark with v2 patch.
Changes in v3:
- Move back to HW frame counter (Rob).
Changes in v4:
- Frame count mismatch was causing a DRM WARN stack spew.
DPU HW will increment the frame count at the end of
the sync, where as vblank will be triggered at the
fetch_start counter which is calculated as v_total - vfp.
This is to start fetching early for panels with low
vbp w.r.t hw latency lines.
Add logic to detect the line count if it falls between
vactive and v_total then return incremented frame count value.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Link: https://lore.kernel.org/r/1613651746-12783-1-git-send-email-kalyan_t@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Performance counts, and ALWAYS_ON counters used for capturing GPU
timestamps, lose their state across suspend/resume cycles. Userspace
tooling for performance monitoring needs to be aware of this. For
example, after a suspend userspace needs to recalibrate it's offset
between CPU and GPU time.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Link: https://lore.kernel.org/r/20210325012358.1759770-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
We were not programing the correct bit while clearing the perfcounter oob.
So, clear it correctly using the new 'clear' bit. This fixes the below
error:
[drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set PERFCOUNTER: 0x80000000
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1617630433-36506-1-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The driver already has support for sm8150/sm8250, but the compatibles were
never added.
Also inverse the non-mdp4 condition in add_display_components() to avoid
having to check every new compatible in the condition.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
After spending a non-negligible time trying to figure out why
dpu_kms_init() would dereference a NULL dpu_kms->pdev, it turns out that
in addition to adding the new compatible to the msm_drv of_match_table
one also need to teach add_display_components() to register the child
nodes - which includes the DPU platform_device.
Replace the open coded test for compatibles with a check against the
match data of the mdss device to save others this trouble in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210317025634.3987908-1-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is a spelling mistake in debugfs gem stats. Fix it. Also
re-align output to cater for the extra 1 character.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210406133939.425987-1-colin.king@canonical.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The last patch lost the breakdown of active vs inactive GEM objects in
$debugfs/gem. But we can add some better stats to summarize not just
active vs inactive, but also purgable/purged to make up for that.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-5-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In normal cases the gem obj lock is acquired first before mm_lock. The
exception is iterating the various object lists. In the shrinker path,
deadlock is avoided by using msm_gem_trylock() and skipping over objects
that cannot be locked. But for debugfs the straightforward thing is to
split things out into a separate list of all objects protected by it's
own lock.
Fixes: d984457b31 ("drm/msm: Add priv->mm_lock to protect active/inactive lists")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
When the system is under heavy memory pressure, we can end up with lots
of concurrent calls into the shrinker. Keeping a running tab on what we
can shrink avoids grabbing a lock in shrinker->count(), and avoids
shrinker->scan() getting called when not profitable.
Also, we can keep purged objects in their own list to avoid re-traversing
them to help cut down time in the critical section further.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unused since commit c951a9b284 ("drm/msm: Remove msm_gem_free_work")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use an explicit set_pgtable_quirks method instead that just passes
the actual quirk bitmask instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20210401155256.298656-20-hch@lst.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Update the 3d merge as active in the data path only if
the hw block is selected in the configuration.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 73bfb790ac ("msm:disp:dpu1: setup display datapath for SC7180 target")
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Message-Id: <1617364493-13518-1-git-send-email-kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
I suppose the microcode version check for a650 is incorrect. It checks
for the version 1.95, while the firmware released have major version of 0:
0.91 (vulnerable), 0.99 (fixing the issue).
Lower version requirements to accept firmware 0.99.
Fixes: 8490f02a3c ("drm/msm: a6xx: Make sure the SQE microcode is safe")
Cc: Akhil P Oommen <akhilpo@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210331140223.3771449-1-dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON. This
isn't the thing that userspace is looking for.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Commit 7bf168c8fe ("drm/msm: Fix speed-bin support not to
access outside valid memory"), reworked the nvmem reading of
"speed_bin", but in doing so dropped handling of the -ENOENT
case which was previously documented as "fine".
That change resulted in the db845c board display to fail to
start, with the following error:
adreno 5000000.gpu: [drm:a6xx_gpu_init] *ERROR* failed to read speed-bin (-2). Some OPPs may not be supported by hardware
Thus, this patch simply re-adds the ENOENT handling so the lack
of the speed_bin entry isn't fatal for display, and gets things
working on db845c.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Fixes: 7bf168c8fe ("drm/msm: Fix speed-bin support not to access outside valid memory")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Message-Id: <20210330013408.2532048-1-john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We should set the platform device's driver data to NULL here so that
code doesn't assume the struct drm_device pointer is valid when it could
have been destroyed. The lifetime of this pointer is managed by a kref
but when msm_drm_init() fails we call drm_dev_put() on the pointer which
will free the pointer's memory. This driver uses the component model, so
there's sort of two "probes" in this file, one for the platform device
i.e. msm_pdev_probe() and one for the component i.e. msm_drm_bind(). The
msm_drm_bind() code is using the platform device's driver data to store
struct drm_device so the two functions are intertwined.
This relationship becomes a problem for msm_pdev_shutdown() when it
tests the NULL-ness of the pointer to see if it should call
drm_atomic_helper_shutdown(). The NULL test is a proxy check for if the
pointer has been freed by kref_put(). If the drm_device has been
destroyed, then we shouldn't call the shutdown helper, and we know that
is the case if msm_drm_init() failed, therefore set the driver data to
NULL so that this pointer liveness is tracked properly.
Fixes: 9d5cbf5fe4 ("drm/msm: add shutdown support for display platform_driver")
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Message-Id: <20210325212822.3663144-1-swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
DPU runtime resume will request for a min vote on the AXI bus as
it is a necessary step before turning ON the AXI clock.
The change does below
1) Move the icc path set before requesting runtime get_sync.
2) remove the dependency of hw catalog for min ib vote
as it is initialized at a later point.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When putting iMX5 into suspend, the following flow is
observed:
[ 70.023427] [<c07755f0>] (msm_atomic_commit_tail) from [<c06e7218>]
(commit_tail+0x9c/0x18c)
[ 70.031890] [<c06e7218>] (commit_tail) from [<c0e2920c>]
(drm_atomic_helper_commit+0x1a0/0x1d4)
[ 70.040627] [<c0e2920c>] (drm_atomic_helper_commit) from
[<c06e74d4>] (drm_atomic_helper_disable_all+0x1c4/0x1d4)
[ 70.050913] [<c06e74d4>] (drm_atomic_helper_disable_all) from
[<c0e2943c>] (drm_atomic_helper_suspend+0xb8/0x170)
[ 70.061198] [<c0e2943c>] (drm_atomic_helper_suspend) from
[<c06e84bc>] (drm_mode_config_helper_suspend+0x24/0x58)
In the i.MX5 case, priv->kms is not populated (as i.MX5 does not use any
of the Qualcomm display controllers), causing a NULL pointer
dereference in msm_atomic_commit_tail():
[ 24.268964] 8<--- cut here ---
[ 24.274602] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
[ 24.283434] pgd = (ptrval)
[ 24.286387] [00000000] *pgd=ca212831
[ 24.290788] Internal error: Oops: 17 [#1] SMP ARM
[ 24.295609] Modules linked in:
[ 24.298777] CPU: 0 PID: 197 Comm: init Not tainted 5.11.0-rc2-next-20210111 #333
[ 24.306276] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 24.312442] PC is at msm_atomic_commit_tail+0x54/0xb9c
[ 24.317743] LR is at commit_tail+0xa4/0x1b0
Fix the problem by calling drm_mode_config_helper_suspend/resume()
only when priv->kms is available.
Fixes: ca8199f134 ("drm/msm/dpu: ensure device suspend happens during PM sleep")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause. Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
While passing the A530-specific lm_setup func to A530 and A540
to !A530 was fine back when only these two were supported, it
certainly is not a good idea to send A540 specifics to smaller
GPUs like A508 and friends.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In commit 9fc418430c ("drm/msm/dp: unplug interrupt missed after
irq_hpd handler") we dropped a reset of the aux phy during aux transfers
because resetting the phy during active communication caused us to miss
an hpd irq in some cases. Unfortunately, we also dropped the part of the
code that changes the aux phy tuning when an aux transfer fails due to a
timeout. That part of the code was calling into the phy driver to
reconfigure the aux TX swing controls, working around poor channel
quality. Let's restore this phy setting code so that aux channel
communication is more reliable.
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Fixes: 9fc418430c ("drm/msm/dp: unplug interrupt missed after irq_hpd handler")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Based on 362cadf34b ("drm/msm/dsi_pll_10nm: Fix variable usage for
pll_lockdet_rate")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 7nm:
remove the TODO by simply using that variable. This is a copy of
196145eb1a ("drm/msm/dsi_pll_10nm: Solve TODO for multiplier frac_bits
assignment").
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.
Cc: Jonathan Marek <jonathan@marek.ca>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When running the latest kernel on an sc7180 with KASAN I got this
splat:
BUG: KASAN: slab-out-of-bounds in a6xx_gpu_init+0x618/0x644
Read of size 4 at addr ffffff8088f36100 by task kworker/7:1/58
CPU: 7 PID: 58 Comm: kworker/7:1 Not tainted 5.11.0+ #3
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x3a8
show_stack+0x24/0x30
dump_stack+0x174/0x1e0
print_address_description+0x70/0x2e4
kasan_report+0x178/0x1bc
__asan_report_load4_noabort+0x44/0x50
a6xx_gpu_init+0x618/0x644
adreno_bind+0x26c/0x438
This is because the speed bin is defined like this:
gpu_speed_bin: gpu_speed_bin@1d2 {
reg = <0x1d2 0x2>;
bits = <5 8>;
};
As you can see the "length" is 2 bytes. That means that the nvmem
subsystem allocates only 2 bytes. The GPU code, however, was casting
the pointer allocated by nvmem to a (u32 *) and dereferencing. That's
not so good.
Let's fix this to just use the nvmem_cell_read_u16() accessor function
which simplifies things and also gets rid of the splat.
Let's also put an explicit conversion from little endian in place just
to make things clear. The nvmem subsystem today is assuming little
endian and this makes it clear. Specifically, the way the above sc7180
cell is interpreted:
NVMEM:
+--------+--------+--------+--------+--------+
| ...... | 0x1d3 | 0x1d2 | ...... | 0x000 |
+--------+--------+--------+--------+--------+
^ ^
msb lsb
You can see that the least significant data is at the lower address
which is little endian.
NOTE: someone who is truly paying attention might wonder about me
picking the "u16" version of this accessor instead of the "u8" (since
the value is 8 bits big) or the u32 version (just for fun). At the
moment you need to pick the accessor that exactly matches the length
the cell was specified as in the device tree. Hopefully future
patches to the nvmem subsystem will fix this.
Fixes: fe7952c629 ("drm/msm: Add speed-bin support to a618 gpu")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
core:
- vblank fence timing improvements
dma-buf:
- improve error handling
ttm:
- memory leak fix
msm:
- a6xx speedbin support
- a508, a509, a512 support
- various a5xx fixes
- various dpu fixes
- qseed3lite support for sm8250
- dsi fix for msm8994
- mdp5 fix for framerate bug with cmd mode panels
- a6xx GMU OOB race fixes that were showing up in CI
- various addition and removal of semicolons
- gem submit fix for legacy userspace relocs path
amdgpu:
- Clang warning fix
- S0ix platform shutdown/poweroff fix
- Misc display fixes
i915:
- color format fix
- -Wuninitialised reenabled
- GVT ww locking, cmd parser fixes
atyfb:
- fix build
rockchip:
- AFBC modifier fix
-----BEGIN PGP SIGNATURE-----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=hrdL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-02-26' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"This is mostly fixes but I missed msm-next pull last week. It's been
in drm-next.
Otherwise it's a selection of i915, amdgpu and misc fixes, one TTM
memory leak, nothing really major stands out otherwise.
core:
- vblank fence timing improvements
dma-buf:
- improve error handling
ttm:
- memory leak fix
msm:
- a6xx speedbin support
- a508, a509, a512 support
- various a5xx fixes
- various dpu fixes
- qseed3lite support for sm8250
- dsi fix for msm8994
- mdp5 fix for framerate bug with cmd mode panels
- a6xx GMU OOB race fixes that were showing up in CI
- various addition and removal of semicolons
- gem submit fix for legacy userspace relocs path
amdgpu:
- clang warning fix
- S0ix platform shutdown/poweroff fix
- misc display fixes
i915:
- color format fix
- -Wuninitialised reenabled
- GVT ww locking, cmd parser fixes
atyfb:
- fix build
rockchip:
- AFBC modifier fix"
* tag 'drm-next-2021-02-26' of git://anongit.freedesktop.org/drm/drm: (60 commits)
drm/panel: kd35t133: allow using non-continuous dsi clock
drm/rockchip: Require the YTR modifier for AFBC
drm/ttm: Fix a memory leak
drm/drm_vblank: set the dma-fence timestamp during send_vblank_event
dma-fence: allow signaling drivers to set fence timestamp
dma-buf: heaps: Rework heap allocation hooks to return struct dma_buf instead of fd
dma-buf: system_heap: Make sure to return an error if we abort
drm/amd/display: Fix system hang after multiple hotplugs (v3)
drm/amdgpu: fix shutdown and poweroff process failed with s0ix
drm/i915: Nuke INTEL_OUTPUT_FORMAT_INVALID
drm/i915: Enable -Wuninitialized
drm/amd/display: Remove Assert from dcn10_get_dig_frontend
drm/amd/display: Add vupdate_no_lock interrupts for DCN2.1
Revert "drm/amd/display: reuse current context instead of recreating one"
drm/amd/pm/swsmu: Avoid using structure_size uninitialized in smu_cmn_init_soft_gpu_metrics
fbdev: atyfb: add stubs for aty_{ld,st}_lcd()
drm/i915/gvt: Introduce per object locking in GVT scheduler.
drm/i915/gvt: Purge dev_priv->gt
drm/i915/gvt: Parse default state to update reg whitelist
dt-bindings: dp-connector: Drop maxItems from -supply
...
Many drivers reference the plane->state pointer in order to get the
current plane state in their atomic_update or atomic_disable hooks,
which would be the new plane state in the global atomic state since
_swap_state happened when those hooks are run.
Use the drm_atomic_get_new_plane_state helper to get that state to make it
more obvious.
This was made using the coccinelle script below:
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
(
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_disable = func,
...,
};
|
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_update = func,
...,
};
)
@ adds_new_state @
identifier plane_atomic_func.func;
identifier plane, state;
identifier new_state;
@@
func(struct drm_plane *plane, struct drm_atomic_state *state)
{
...
- struct drm_plane_state *new_state = plane->state;
+ struct drm_plane_state *new_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20210219120032.260676-1-maxime@cerno.tech
* a6xx speedbin support
* a508, a509, a512 support
* various a5xx fixes
* various dpu fixes
* qseed3lite support for sm8250
* dsi fix for msm8994
* mdp5 fix for framerate bug with cmd mode panels
* a6xx GMU OOB race fixes that were showing up in CI
* various addition and removal of semicolons
* gem submit fix for legacy userspace relocs path
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvh3tvLz_xtk=4x9xUfo2h2s4xkniOvC7HyLO2jrXnXkw@mail.gmail.com
Many drivers reference the plane->state pointer in order to get the
current plane state in their atomic_check hook, which would be the old
plane state in the global atomic state since _swap_state hasn't happened
when atomic_check is run.
Use the drm_atomic_get_old_plane_state helper to get that state to make
it more obvious.
This was made using the coccinelle script below:
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
static struct drm_plane_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@ replaces_old_state @
identifier plane_atomic_func.func;
identifier plane, state, plane_state;
@@
func(struct drm_plane *plane, struct drm_atomic_state *state) {
...
- struct drm_plane_state *plane_state = plane->state;
+ struct drm_plane_state *plane_state = drm_atomic_get_old_plane_state(state, plane);
...
}
@@
identifier plane_atomic_func.func;
identifier plane, state, plane_state;
@@
func(struct drm_plane *plane, struct drm_atomic_state *state) {
struct drm_plane_state *plane_state = drm_atomic_get_old_plane_state(state, plane);
<...
- plane->state
+ plane_state
...>
}
@ adds_old_state @
identifier plane_atomic_func.func;
identifier plane, state;
@@
func(struct drm_plane *plane, struct drm_atomic_state *state) {
+ struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane);
<...
- plane->state
+ old_plane_state
...>
}
@ include depends on adds_old_state || replaces_old_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && (adds_old_state || replaces_old_state) @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-6-maxime@cerno.tech
The current atomic helpers have either their object state being passed as
an argument or the full atomic state.
The former is the pattern that was done at first, before switching to the
latter for new hooks or when it was needed.
Let's convert all the remaining helpers to provide a consistent
interface, starting with the planes atomic_check.
The conversion was done using the coccinelle script below plus some
manual changes for vmwgfx, built tested on all the drivers.
@@
identifier plane, plane_state;
symbol state;
@@
struct drm_plane_helper_funcs {
...
int (*atomic_check)(struct drm_plane *plane,
- struct drm_plane_state *plane_state);
+ struct drm_atomic_state *state);
...
}
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
struct drm_plane_helper_funcs *FUNCS;
identifier f;
identifier dev;
identifier plane, plane_state, state;
@@
f(struct drm_device *dev, struct drm_atomic_state *state)
{
<+...
- FUNCS->atomic_check(plane, plane_state)
+ FUNCS->atomic_check(plane, state)
...+>
}
@ ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
... when != new_plane_state
}
@ adds_new_state depends on plane_atomic_func && !ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
+ struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ depends on plane_atomic_func @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane,
- struct drm_plane_state *new_plane_state
+ struct drm_atomic_state *state
)
{ ... }
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-4-maxime@cerno.tech
Most a6xx targets have security issues that were fixed with new versions
of the microcode(s). Make sure that we are booting with a safe version of
the microcode for the target and print a message and error if not.
v2: Add more informative error messages and fix typos
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The cleanup patch broke a6xx_gmu_clear_oob, fix it by adding the missing
bitshift operation.
Fixes: 555c50a4a1 ("drm/msm: Clean up GMU OOB set/clear handling")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We don't need to make up custom lock classes here, we can simply use
mutex_lock_nested() and pass in the index of the crtc to the locking
APIs instead. This helps lockdep understand that these are really
different locks while avoiding having to allocate custom lockdep
classes.
Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: b3d91800d9 ("drm/msm: Fix race condition in msm driver with async layer updates")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The function drm_gem_fb_prepare_fb() is a helper for atomic modesetting,
but currently located next to framebuffer helpers. Move it to GEM atomic
helpers, rename it slightly and adopt the drivers. Same for the rsp
simple-pipe helper.
Compile-tested with x86-64, aarch64 and arm. The patch is fairly large,
but there are no functional changes.
v3:
* remove out-comented line in drm_gem_framebuffer_helper.h
(Maxime)
v2:
* rename to drm_gem_plane_helper_prepare_fb() (Daniel)
* add tutorial-style documentation
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222141756.7864-1-tzimmermann@suse.de
Switch DRM drivers from drm_get_format_name() to %p4cc. This gets rid of a
large number of temporary variables at the same time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216155723.17109-4-sakari.ailus@linux.intel.com
A missing semicolon here causes my external display to stop working.
Indeed, missing the semicolon on the return statement leads to
dp_panel_update_tu_timings() not existing because the compiler thinks
it's part of the return statement of a void function, so it must not be
important.
$ ./scripts/bloat-o-meter before.o after.o
add/remove: 1/1 grow/shrink: 0/1 up/down: 7400/-7540 (-140)
Function old new delta
dp_panel_update_tu_timings - 7400 +7400
_dp_ctrl_calc_tu.constprop 18024 17900 -124
dp_panel_update_tu_timings.constprop 7416 - -7416
Total: Before=54440, After=54300, chg -0.26%
Add a semicolon so this function works like it used to.
Cc: Sean Paul <sean@poorly.run>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: cc9014bf63 ("drm/msm/dp/dp_ctrl: Move 'tu' from the stack to the heap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
DP_SW_RESET is the global SW reset that is used to initialize DP
controller. If DP_SW_RESET executed during connection setup,
two HPD related side effects may occurred,
1) pending HPD interrupts cleared unexpected
2) re start debounce logic which trigger another interrupt
This patch only issue DP_SW_RESET at boot up and pm_resume.
This patch also reinit video_comp before configure dp controller
to avoid missing VIDEO_READY interrupt.
Fixes: 9fc418430c ("drm/msm/dp: unplug interrupt missed after irq_hpd handler")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In moving code around, we ended up using the same pointer to
copy_from_user() the relocs tables as we used for the cmd table
entry, which is clearly not right. This went unnoticed because
modern mesa on non-ancent kernels does not actually use relocs.
But this broke ancient mesa on modern kernels.
Reported-by: Emil Velikov <emil.velikov@collabora.com>
Fixes: 20224d715a ("drm/msm/submit: Move copy_from_user ahead of locking bos")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
The maximum mdp clock rate on msm8974v2 is 320MHz. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
remove unneeded variable: "rc".
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_set_bw() is getting removed and dev_pm_opp_set_opp() should
be used instead. Migrate to the new API.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
DRM_DEV_ERROR should be used across this entire source: convert the
pr_err prints to the first as a cleanup.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 10nm:
remove the TODO by simply using that variable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In function dsi_pll_calc_dec_frac we are calculating the decimal
div start parameter by dividing the decimal multiple by the
fractional multiplier: the remainder of that operation is stored
to then get programmed to the fractional divider registers of
the PLL.
It's useless to call div_u64_rem to get the remainder and *then*
call div_u64 to get the division result, as the first is already
giving that result: let's fix it by just caring about the result
of div_u64_rem.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
1. Trigger the unplug event in msm_dp_display_disable() to shutdown audio
properly.
2. Reset the completion before signal the disconnect event.
Fixes: 158b9aa744 ("drm/msm/dp: wait for audio notification before disabling clocks")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
fix semicolon.cocci warnings:
drivers/gpu/drm/msm/dp/dp_ctrl.c:1161:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Rob Clark <robdclark@chromium.org>
fix semicolon.cocci warnings:
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:752:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix below warnings reported by coccicheck:
./drivers/gpu/drm/msm/msm_gem.c:991:3-9: WARNING: NULL check before some
freeing functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Lockdep complains about an AA deadlock when rebooting the device.
base-commit: 19c329f680
============================================
WARNING: possible recursive locking detected
5.4.91 #1 Not tainted
--------------------------------------------
reboot/5213 is trying to acquire lock:
ffffff80d13391b0 (&kms->commit_lock[i]){+.+.}, at: lock_crtcs+0x60/0xa4
but task is already holding lock:
ffffff80d1339110 (&kms->commit_lock[i]){+.+.}, at: lock_crtcs+0x60/0xa4
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&kms->commit_lock[i]);
lock(&kms->commit_lock[i]);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by reboot/5213:
__arm64_sys_reboot+0x148/0x2a0
device_shutdown+0x10c/0x2c4
drm_atomic_helper_shutdown+0x48/0xfc
modeset_lock+0x120/0x24c
lock_crtcs+0x60/0xa4
stack backtrace:
CPU: 4 PID: 5213 Comm: reboot Not tainted 5.4.91 #1
Hardware name: Google Pompom (rev1) with LTE (DT)
Call trace:
dump_backtrace+0x0/0x1dc
show_stack+0x24/0x30
dump_stack+0xfc/0x1a8
__lock_acquire+0xcd0/0x22b8
lock_acquire+0x1ec/0x240
__mutex_lock_common+0xe0/0xc84
mutex_lock_nested+0x48/0x58
lock_crtcs+0x60/0xa4
msm_atomic_commit_tail+0x348/0x570
commit_tail+0xdc/0x178
drm_atomic_helper_commit+0x160/0x168
drm_atomic_commit+0x68/0x80
This is because lockdep thinks all the locks taken in lock_crtcs() are
the same lock, when they actually aren't. That's because we call
mutex_init() in msm_kms_init() and that assigns one static key for every
lock initialized in this loop. Let's allocate a dynamic number of
lock_class_keys and assign them to each lock so that lockdep can figure
out an AA deadlock isn't possible here.
Fixes: b3d91800d9 ("drm/msm: Fix race condition in msm driver with async layer updates")
Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that the bug is fixed in the minimal way for stable, go make the
code table-driven.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that we're not racing with GPU setup, also fix races of timestamps
against other timestamps. In freedreno CI, we were seeing this path trigger
timeouts on setting the GMU bit, producing:
[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0
and this triggered especially on the first set of tests right after
boot (it's probably easier to lose the race than one might think,
given that we start many tests in parallel, and waiting for NFS to
page in code probably means that lots of tests hit the same point of
screen init at the same time). As of this patch, the message seems to
have completely gone away.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We were using the same force-poweron bit in the two codepaths, so they
could race to have one of them lose GPU power early.
freedreno CI was seeing intermittent errors like:
[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0
and this issue could have contributed to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5a2 ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before the offending commit in msm_atomic_commit_tail wait_flush was
called once per frame, after the commit was submitted. After it
wait_flush is also called at the beginning to ensure previous
potentially async commits are done.
For cmd panels the source of wait_flush is a ping-pong irq notifying
a completion. The completion needs to be notified with complete_all so
multiple waiting parties (new async committers) can proceed.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Suggested-by: Rob Clark <robdclark@gmail.com>
Fixes: 2d99ced787 ("drm/msm: async commit support")
Signed-off-by: Rob Clark <robdclark@chromium.org>
The previous registers were *almost* correct, but instead of
PHYs, they were pointing at DSI PLLs, resulting in the PHY id
autodetection failing miserably.
Fixes: dcefc117cc ("drm/msm/dsi: Add support for msm8x94")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
SM8250 has quite unique qseed lut type: qseed3lite, which is a
lightweight version of qseed3 scaler.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is HPD unplug interrupts missed at scenario of an irq_hpd
followed by unplug interrupts with around 10 ms in between.
Since both AUX_SW_RESET and DP_SW_RESET clear pending HPD interrupts,
irq_hpd handler should not issues either aux or sw reset to avoid
following unplug interrupt be cleared accidentally. This patch
also postpone handling of irq_hpd until connected state if it
happened at connection pending state.
Changes in V2:
-- add postpone handling of irq_hpd until connected state
-- check DP_TRAINING_1 instead of DP_TRAINING_NONE
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The call to dpu_encoder_phys_cmd_prepare_for_kickoff is useless as
it's unused because the serialize_wait4pp variable is never set to
true by .. anything, literally: remove the call.
While at it, also reduce indentation by inverting the check for
dpu_encoder_phys_cmd_is_master.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When configuring the tearcheck, the parameters for the engine were
being set mostly as they should've been, but then it wasn't getting
configured to get the vsync indication from the TE GPIO input
because it was assumed that autorefresh could be enabled:
since a previous commit makes sure to disable the autorefresh bit
when committing to the cmd engine, it is now safe to just enable
the vsync pin input at tearcheck setup time (instead of erroneously
never enabling it).
Also, set the right sync_cfg_height to enable the DPU auto-generated
TE signal in order to avoid stalls in the event that we miss one
external TE signal: this will still trigger recovery mechanisms in
case the display is really unreachable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When a command mode display is used, it may be retaining the bootloader
configuration which, in most of the cases, enables the autorefresh
feature in order to keep the splash up.
Since there is no autorefresh management in this driver, wire up the
autorefresh ops in the dpu_hw_pingpong and disable the feature when
preparing for cmd commit: instead of disabling it when initializing
the command mode, this road was chosen as to open future possibility
of enabling and managing the autorefresh feature in the driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DSPP_BLK macro was ad-hoc made for SC7180, but this is wrong
because not all of the DPU DSPP versions can use the same DSPP block
configuration, and not all of them have got the same features.
For this reason, add two more params to the DSPP_BLK macro, so that
it is possible to specify the feature mask and the sblk config for
each DSPP.
Fixes: 4259ff7ae5 ("drm/msm/dpu: add support for pcc color block in dpu driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Not all DPU interface sub-block versions need the same value for
prog_fetch_lines_worst_case: add this to the INTF_BLK macro, so
that it becomes possible to vary it for other INTF versions.
For example, this is needed to implement support for older SoCs,
like MSM8998 and SDM630/660 and most probably will also be needed
for future SoCs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Not all DPU versions that are supported in this driver are supposed
to have a 8-Levels VIG QoS setting.
Move this flag to SDM845 and SC7180 specific masks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On DPUs prior to version 4 the VBIF_XINL_QOS_LVL_REMAP_000 register
is at 0x570 offset from vbif base instead of 0x590, due to the
VBIF_XINL_QOS_RP_REMAP_000 having less instances (less possible XINs).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The upstream API for some reason uses logbase2 instead of
just passing the argument as-is, whereas downstream CAF
kernel does the latter.
Hence, a mistake has been made when porting:
4 is the value that's supposed to be passed, but
log2(4) = 2. Changing the value to 16 (= 2^4) fixes
the issue.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Resetting the VBIF before power collapse is done to avoid getting
bogus FIFO entries during the suspend sequence or subsequent resume,
but this is doable only on Adreno 510 and Adreno 530, as the other
units will tendentially lock up.
Especially on Adreno 508, the GPU will show lockups and very bad
slownesses after processing the first frame.
Avoiding to execute the RBBM SW Reset before suspend will stop the
lockup issue from happening on at least Adreno 508/509/512.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The Adreno 508/509/512 GPUs are stripped versions of the Adreno
5xx found in the mid-end SoCs such as SDM630, SDM636, SDM660 and
SDA variants; these SoCs are usually provided with ZAP firmwares,
but they have no available GPMU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Tested-by: Martin Botka <martin.botka1@gmail.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The "main" if branch where we program the other registers for the
Adreno 5xx family of GPUs should not contain the PC_DBG_ECO_CNTL
register programming because this has logical similarity
differences from all the others.
A later commit will show the entire sense of this.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The PC_DBG_ECO_CNTL register on the Adreno A5xx family gets
programmed to some different values on a per-model basis.
At least, this is what we intend to do here;
Unfortunately, though, this register is being overwritten with a
static magic number, right after applying the GPU-specific
configuration (including the GPU-specific quirks) and that is
effectively nullifying the efforts.
Let's remove the redundant and wrong write to the PC_DBG_ECO_CNTL
register in order to retain the wanted configuration for the
target GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
A6XX GPUs have support for last level cache(LLC) also known
as system cache and need to set the bus attributes to
use it. Currently we use a generic adreno iommu address space
implementation which are also used by older GPU generations
which do not have LLC and might introduce issues accidentally
and is not clean in a way that anymore additions of GPUs
supporting LLC would have to be guarded under ifdefs. So keep
the generic code separate and make the address space creation
A6XX specific. We also have a helper to set the llc attributes
so that if the newer GPU generations do support them, we can
use it instead of open coding domain attribute setting for each
GPU.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Domain attribute setting for LLCC is guarded by !IS_ERR
check which works fine only when CONFIG_QCOM_LLCC=y but
when it is disabled, the LLCC apis return NULL and that
is not handled by IS_ERR check. Due to this, domain attribute
for LLCC will be set even on GPUs which do not support it
and cause issues, so correct this by using IS_ERR_OR_NULL
checks appropriately. Meanwhile also cleanup comment block
and remove unwanted blank line.
Fixes: 00fd44a1a4 ("drm/msm: Only enable A6xx LLCC code on A6xx")
Fixes: 474dadb8b0 ("drm/msm/a6xx: Add support for using system cache(LLC)")
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On at least MSM8998 it's possible to find Adreno 540.0 and 540.1
but I have never found any 540.2. In any case, the patchids 0-1
for A540 are completely supported by this driver and there is no
reason to disallow probing them (as they also share the same
firmware names).
Besides that, the patchid number is also used in the a5xx_power.c
function a540_lm_setup to disable the battery current limiter,
which makes faking the Adreno patchid to .2 (which would anyway
be sad) useless and even producing breakages.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The msm_gem_get_iova should be guarded with gpu != NULL and not aspace
!= NULL, because aspace is NULL when using vram carveout.
Fixes: 933415e24b ("drm/msm: Add support for private address space instances")
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some GPUs support different max frequencies depending on the platform.
To identify the correct variant, we should check the gpu speedbin
fuse value. Add support for this speedbin detection to a6xx family
along with the required fuse details for a618 gpu.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
- Fix DP vswing settings and handling (Imre, Ville)
- Various display code clean-up (Jani, Ville)
- Various display refactoring, including split out of pps, aux, and fdi (Ja\
ni, Dave)
- Add DG1 missing workarounds (Jose)
- Fix display color conversion (Chris, Ville)
- Try to guess PCH type even without ISA bridge (Zhenyu)
- More backlight refactor (Lyude)
- Support two CSC module on gen11 and later (Lee)
- Async flips for all ilk+ platforms (Ville)
- Clear color support for TGL (RK)
- Add a helper to read data from a GEM object page (Imre)
- VRR/Adaptive Sync Enabling on DP/eDP for TGL+ (Manasi, Ville Aditya)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmARc1oACgkQ+mJfZA7r
E8ovFAgAhBlnhrquGrgtuRmS5tkpLQShqiwrPv7ogDBkcayJ6Is+AO+FoE8kuzZO
q/TW2enkcRKFHhQnm9RA0Ayk+rwYqkEOcBU5gvzusdwbEjkygJfH/yA2ukAmaw32
QxP9A2pW+iWsEcqtMuOEu1ahu0Z8gnkCe8DakuBMf/0y5D9DairwaCC8nyZQdEJq
YFTxp+pILE57PhOVbKS3EZPbnl5t28NgCtMc8hjlPTWZxRSVV0eDrY2tx9vyhFhU
Eq8aLDxPKCRm18sg+J+lDytOvFoljXcglAEwPODVMmDNolG8R6aRQ9T6tG6qfxyI
UO1KyeYUHHEIJ4IBJKK+KWeUWLLBhA==
=3Jc8
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2021-01-27' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- HDCP 2.2 and HDCP 1.4 Gen12 DP MST support (Anshuman)
- Fix DP vswing settings and handling (Imre, Ville)
- Various display code clean-up (Jani, Ville)
- Various display refactoring, including split out of pps, aux, and fdi (Ja\
ni, Dave)
- Add DG1 missing workarounds (Jose)
- Fix display color conversion (Chris, Ville)
- Try to guess PCH type even without ISA bridge (Zhenyu)
- More backlight refactor (Lyude)
- Support two CSC module on gen11 and later (Lee)
- Async flips for all ilk+ platforms (Ville)
- Clear color support for TGL (RK)
- Add a helper to read data from a GEM object page (Imre)
- VRR/Adaptive Sync Enabling on DP/eDP for TGL+ (Manasi, Ville Aditya)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210127140822.GA711686@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmAOFRIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4lcH/jFAG+AXR6T2K3dG
adJmdAWQKdDj71Ruoyefx5GSbD0B+rM1UcxOQgmZem2127RJgfDBBVYyjSwh7H1F
LRJdN6+NKReL2OW/HMnufvpVMvWICTWHInyvsqKqp+Yo4GC5z46OtsmzSayYgTaP
v2G9auC/rSUlzmQux9EAbTKDeNGMum3dt2rfsmnIDymBSHoPbizXF93/2hoo9jwx
BZQCq0nYBCa9pEdsmgvqKkb/Y5+CSFoe02qdUZFIuwh6qd/XPfeDPSu4O3z4J9g6
x8G+f7doeU0nzsAP+K0lG7ulAygxRHm5Bn2rwVdlYfihAuPNyF+Ua3duxBvjOBEY
7w/UQ64=
=ZWS9
-----END PGP SIGNATURE-----
Merge tag 'v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge v5.11-rc5 into drm-next to clean up a bunch of conflicts we are dragging around.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 7c553f8b5a ("drm/dp: Revert "drm/dp: Introduce EDID-based
quirks"") removed drm_dp_get_edid_quirks() and changed the signature of
drm_dp_has_quirk() while they were still being used in msm. Fix the
breakage. Functionally, removing the EDID-based quirks has no impact on
msm.
[The above commit was merged to drm-intel-next; make two wrongs a right
by merging this fix through drm-intel-next as well.]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
References: http://lore.kernel.org/r/20210120105715.4391dd95@canb.auug.org.au
Fixes: 7c553f8b5a ("drm/dp: Revert "drm/dp: Introduce EDID-based quirks"")
Cc: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210120110708.32131-1-jani.nikula@intel.com
Using this code on A5xx (and probably older too) causes a
smmu bug.
Fixes: 474dadb8b0 ("drm/msm/a6xx: Add support for using system cache(LLC)")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Using the GPU with a VRAM Carveout is a security vulnerability.
Nevertheless it is sometimes required, especially when no IOMMU
implementation is available for a certain platform.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
vram.size is needed when binding a gpu without an iommu and is defined
in msm_init_vram(), so run that before binding it.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
irq_hpd event can only be executed at connected state. Therefore
irq_hpd event should be postponed if it happened at connection
pending state. This patch also make sure both link rate and lane
are valid before start link training.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
-----BEGIN PGP SIGNATURE-----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=orEC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-12-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
get_pages is only called in a locked context. Add a WARN_ON to make sure
it stays that way.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers
-----BEGIN PGP SIGNATURE-----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=BhU/
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Daniel Vetter:
"UAPI Changes:
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers"
* tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm: (117 commits)
drm/qxl: don't allocate a dma_address array
drm/nouveau: fix multihop when move doesn't work.
drm/i915/tgl: Fix REVID macros for TGL to fetch correct stepping
drm/i915: Fix mismatch between misplaced vma check and vma insert
drm/i915/perf: also include Gen11 in OATAILPTR workaround
Revert "drm/i915: re-order if/else ladder for hpd_irq_setup"
drm/amdgpu/disply: fix documentation warnings in display manager
drm/amdgpu: print mmhub client name for dimgrey_cavefish
drm/amdgpu: set mode1 reset as default for dimgrey_cavefish
drm/amd/display: Add get_dig_frontend implementation for DCEx
drm/radeon: remove h from printk format specifier
drm/amdgpu: remove h from printk format specifier
drm/amdgpu: Fix spelling mistake "Heterogenous" -> "Heterogeneous"
drm/amdgpu: fix regression in vbios reservation handling on headless
drm/amdgpu/SRIOV: Extend VF reset request wait period
drm/amdkfd: correct amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu log.
drm/amd/display: Adding prototype for dccg21_update_dpp_dto()
drm/amdgpu: print what method we are using for runtime pm
drm/amdgpu: simplify logic in atpx resume handling
drm/amdgpu: no need to call pci_ignore_hotplug for _PR3
...
- IOVA allocation optimisations and removal of unused code
- Introduction of DOMAIN_ATTR_IO_PGTABLE_CFG for parameterising the
page-table of an IOMMU domain
- Support for changing the default domain type in sysfs
- Optimisation to the way in which identity-mapped regions are created
- Driver updates:
* Arm SMMU updates, including continued work on Shared Virtual Memory
* Tegra SMMU updates, including support for PCI devices
* Intel VT-D updates, including conversion to the IOMMU-DMA API
- Cleanup, kerneldoc and minor refactoring
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl/XWy8QHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNPejB/46QsXATkWt7hbDPIxlUvzUG8VP/FBNJ6A3
/4Z+4KBXR3zhvZJOEqTarnm6Uc22tWkYpNS3QAOuRW0EfVeD8H+og4SOA2iri5tR
x3GZUCng93APWpHdDtJP7kP/xuU47JsBblY/Ip9aJKYoXi9c9svtssAqKr008wxr
knv/xv/awQ0O7CNc3gAoz7mUagQxG/no+HMXMT3Fz9KWRzzvTi6s+7ZDm2faI0hO
GEJygsKbXxe1qbfeGqKTP/67EJVqjTGsLCF2zMogbnnD7DxadJ2hP0oNg5tvldT/
oDj9YWG6oLMfIVCwDVQXuWNfKxd7RGORMbYwKNAaRSvmkli6625h
=KFOO
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull IOMMU updates from Will Deacon:
"There's a good mixture of improvements to the core code and driver
changes across the board.
One thing worth pointing out is that this includes a quirk to work
around behaviour in the i915 driver (see 65f746e828 ("iommu: Add
quirk for Intel graphic devices in map_sg")), which otherwise
interacts badly with the conversion of the intel IOMMU driver over to
the DMA-IOMMU APU but has being fixed properly in the DRM tree.
We'll revert the quirk later this cycle once we've confirmed that
things don't fall apart without it.
Summary:
- IOVA allocation optimisations and removal of unused code
- Introduction of DOMAIN_ATTR_IO_PGTABLE_CFG for parameterising the
page-table of an IOMMU domain
- Support for changing the default domain type in sysfs
- Optimisation to the way in which identity-mapped regions are
created
- Driver updates:
* Arm SMMU updates, including continued work on Shared Virtual
Memory
* Tegra SMMU updates, including support for PCI devices
* Intel VT-D updates, including conversion to the IOMMU-DMA API
- Cleanup, kerneldoc and minor refactoring"
* tag 'iommu-updates-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (50 commits)
iommu/amd: Add sanity check for interrupt remapping table length macros
dma-iommu: remove __iommu_dma_mmap
iommu/io-pgtable: Remove tlb_flush_leaf
iommu: Stop exporting free_iova_mem()
iommu: Stop exporting alloc_iova_mem()
iommu: Delete split_and_remove_iova()
iommu/io-pgtable-arm: Remove unused 'level' parameter from iopte_type() macro
iommu: Defer the early return in arm_(v7s/lpae)_map
iommu: Improve the performance for direct_mapping
iommu: avoid taking iova_rbtree_lock twice
iommu/vt-d: Avoid GFP_ATOMIC where it is not needed
iommu/vt-d: Remove set but not used variable
iommu: return error code when it can't get group
iommu: Fix htmldocs warnings in sysfs-kernel-iommu_groups
iommu: arm-smmu-impl: Add a space before open parenthesis
iommu: arm-smmu-impl: Use table to list QCOM implementations
iommu/arm-smmu: Move non-strict mode to use io_pgtable_domain_attr
iommu/arm-smmu: Add support for pagetable config domain attribute
iommu: Document usage of "/sys/kernel/iommu_groups/<grp_id>/type" file
iommu: Take lock before reading iommu group default domain type
...
Required backmerge since we will be based on top of v5.11, and there
has been a request to backmerge already to upstream some features.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
* Shutdown hook for GPU (to ensure GPU is idle before iommu goes away)
* GPU cooling device support
* DSI 7nm and 10nm phy/pll updates
* Additional sm8150/sm8250 DPU support (merge_3d and DSPP color
processing)
* Various DP fixes
* A whole bunch of W=1 fixes from Lee Jones
* GEM locking re-work (no more trylock_recursive in shrinker!)
* LLCC (system cache) support
* Various other fixes/cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGt0G=H3_RbF_GAQv838z5uujSmFd+7fYhL6Yg=23LwZ=g@mail.gmail.com
The only user of tlb_flush_leaf is a particularly hairy corner of the
Arm short-descriptor code, which wants a synchronous invalidation to
minimise the races inherent in trying to split a large page mapping.
This is already far enough into "here be dragons" territory that no
sensible caller should ever hit it, and thus it really doesn't need
optimising. Although using tlb_flush_walk there may technically be
more heavyweight than needed, it does the job and saves everyone else
having to carry around useless baggage.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/9844ab0c5cb3da8b2f89c6c2da16941910702b41.1606324115.git.robin.murphy@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The iommu pgtable support is only available when IOMMU support
is built into the kernel:
WARNING: unmet direct dependencies detected for IOMMU_IO_PGTABLE
Depends on [n]: IOMMU_SUPPORT [=n]
Selected by [y]:
- DRM_MSM [=y] && HAS_IOMEM [=y] && DRM [=y] && (ARCH_QCOM [=y] || SOC_IMX5 || ARM && COMPILE_TEST [=y]) && OF [=y] && COMMON_CLK [=y] && MMU [=y] && (QCOM_OCMEM [=y] || QCOM_OCMEM [=y]=n)
Fix the dependency accordingly. There is no need for depending on
CONFIG_MMU any more, as that is implied by the iommu support.
Fixes: b145c6e65e ("drm/msm: Add support to create a local pagetable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@chromium.org>
nr_rings is reset to 1, but when this function is called for a second
(and third!) time nr_rings > 1 is false, thus the else case is entered
to set up a buffer for the RPTR shadow and consequently written to
RB_RPTR_ADDR, hanging platforms without WHERE_AM_I firmware support.
Restructure the condition in such a way that shadow buffer setup only
ever happens when has_whereami is true; otherwise preemption is only
finalized when the number of ring buffers has not been reset to 1 yet.
Fixes: 8907afb476 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add support for color correction sub block on SM8150 and SM8250.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When using gem with vram carveout the page allocation is managed via
drm_mm. The necessary drm_mm_node is allocated in add_vma, but it is
referenced in msm_gem_object as well. It is freed before the drm_mm_node
has been deallocated leading to use-after-free on every single vram
allocation.
Currently put_iova is called before put_pages in both
msm_gem_free_object and msm_gem_purge:
put_iova -> del_vma -> kfree(vma) // vma holds drm_mm_node
/* later */
put_pages -> put_pages_vram -> drm_mm_remove_node(
msm_obj->vram_node)
// vram_node is a ref to
// drm_mm_node; in _msm_gem_new
It looks like del_vma does nothing else other than freeing the vma
object and removing it from it's list, so delaying the deletion should
be harmless.
This patch splits put_iova in put_iova_spaces and put_iova_vmas, so the
vma can be freed after the mm_node has been deallocated with the mm.
Note: The breaking commit separated the vma allocation from within
msm_gem_object to outside, so the vram_node reference became outside the
msm_gem_object allocation, and freeing order was therefore overlooked.
Fixes: 4b85f7f5cf ("drm/msm: support for an arbitrary number of address spaces")
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some usb type-c dongle use irq_hpd request to perform device connection
and disconnection. This patch add handling of both connection and
disconnection are based on the state of hpd_state and sink_count.
Changes in V2:
-- add dp_display_handle_port_ststus_changed()
-- fix kernel test robot complaint
Changes in V3:
-- add encoder_mode_set into struct dp_display_private
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 26b8d66a39 ("drm/msm/dp: promote irq_hpd handle to handle link training correctly")
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Update the qos remap only if the client type changes for the plane.
This will avoid unnecessary register programming and also avoid log
spam from the dpu_vbif_set_qos_remap() function.
changes in v2:
- get rid of the dirty flag and simplify the logic to call
_dpu_plane_set_qos_remap()
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.c:246: error: Cannot parse struct or union!
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_interrupts.c:756: error: Cannot parse struct or union!
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Shubhashree Dhar <dhar@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Mapping the imported pages of a DMA-buf into an userspace process
doesn't work as expected.
But we have reoccurring requests on this approach, so split the
functions for this and document that dma_buf_mmap() needs to be used
instead.
v2: split it into two functions
v3: rebased on latest changes
v4: update commit message a bit
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/403838/
In case of panels with low vertical back porch, the prefill bw
requirement will be high as we will have less time(vbp+pw) to
fetch and fill the hw latency buffers before start of first line
in active period.
For ex:
Say hw_latency_line_buffers = 24, and if blanking vbp+pw = 10
Here we need to fetch 24 lines of data in 10 line times.
This will increase the bw to the ratio of linebuffers to blanking.
DPU hw can also fetch data during vertical front porch provided
interface prefetch is enabled. Use vfp in the prefill calculation
as dpu driver enables prefetch if the blanking is not sufficient
to fill the latency lines.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
GPU targets with an MMU-500 attached have a slightly different process for
enabling system cache. Use the compatible string on the IOMMU phandle
to see if an MMU-500 is attached and modify the programming sequence
accordingly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The last level system cache can be partitioned to 32 different
slices of which GPU has two slices preallocated. One slice is
used for caching GPU buffers and the other slice is used for
caching the GPU SMMU pagetables. This talks to the core system
cache driver to acquire the slice handles, configure the SCID's
to those slices and activates and deactivates the slices upon
GPU power collapse and restore.
Some support from the IOMMU driver is also needed to make use
of the system cache to set the right TCR attributes. GPU then
has the ability to override a few cacheability parameters which
it does to override write-allocate to write-no-allocate as the
GPU hardware does not benefit much from it.
DOMAIN_ATTR_IO_PGTABLE_CFG is another domain level attribute used
by the IOMMU driver for pagetable configuration which will be used
to set a quirk initially to set the right attributes to cache the
hardware pagetables into the system cache.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
[saiprakash.ranjan: fix to set attr before device attach to iommu and rebase]
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The register read-modify-write construct is generic enough
that it can be used by other subsystems as needed, create
a more generic rmw() function and have the gpu_rmw() use
this new function.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
linux/rational.h is included more than once, Remove the one that isn't
necessary.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only usage of dsi_host_ops is to assign its address to the ops field
in the mipi_dsi_host struct, which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
'struct tu_algo_data' is huge ~400 Bytes.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/dp/dp_ctrl.c: In function ‘_dp_ctrl_calc_tu.constprop’:
drivers/gpu/drm/msm/dp/dp_ctrl.c:938:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:83:7: warning: no previous prototype for ‘state_kcalloc’ [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:95:7: warning: no previous prototype for ‘state_kmemdup’ [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:947:6: warning: no previous prototype for ‘a6xx_gpu_state_destroy’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/msm_gem_shrinker.c:108: warning: Function parameter or member 'dev' not described in 'msm_gem_shrinker_init'
drivers/gpu/drm/msm/msm_gem_shrinker.c:108: warning: Excess function parameter 'dev_priv' description in 'msm_gem_shrinker_init'
drivers/gpu/drm/msm/msm_gem_shrinker.c:126: warning: Function parameter or member 'dev' not described in 'msm_gem_shrinker_cleanup'
drivers/gpu/drm/msm/msm_gem_shrinker.c:126: warning: Excess function parameter 'dev_priv' description in 'msm_gem_shrinker_cleanup'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/msm_drv.c:124:15: warning: no previous prototype for ‘_msm_ioremap’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Function parameter or member 'plane' not described in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Function parameter or member 'fb' not described in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Excess function parameter 'Plane' description in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:200: warning: Function parameter or member 'plane' not described in '_dpu_plane_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:200: warning: Excess function parameter 'Plane' description in '_dpu_plane_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:232: warning: Function parameter or member 'src_width' not described in '_dpu_plane_calc_fill_level'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:232: warning: Excess function parameter 'src_wdith' description in '_dpu_plane_calc_fill_level'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1060: warning: Function parameter or member 'error' not described in 'dpu_plane_set_error'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:150: warning: Function parameter or member 'dpu_kms' not described in 'dpu_vbif_set_ot_limit'
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:150: warning: Excess function parameter 'vbif' description in 'dpu_vbif_set_ot_limit'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:247: warning: Excess function parameter 'Return' description in '_dpu_rm_check_lm_peer'
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:283: warning: Function parameter or member 'global_state' not described in '_dpu_rm_check_lm_and_get_connected_blks'
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:283: warning: Excess function parameter 'Return' description in '_dpu_rm_check_lm_and_get_connected_blks'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'ctx' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'fmt' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'flags' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'rect_mode' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'ctx' not described in 'dpu_hw_sspp_setup_rects'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'cfg' not described in 'dpu_hw_sspp_setup_rects'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'rect_index' not described in 'dpu_hw_sspp_setup_rects'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c:55: warning: Function parameter or member 'ctx' not described in '_stage_offset'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c:55: warning: Excess function parameter 'c' description in '_stage_offset'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'cur_slave' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'hw_pp' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'intfs_swapped' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'drm_enc' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'phys' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'extra_flush_bits' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1481: warning: Function parameter or member 'phys' not described in '_dpu_encoder_trigger_start'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1564: warning: Function parameter or member 'dpu_enc' not described in '_dpu_encoder_kickoff_phys'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
These tables are not large or overbearing, so moving them into the
source file seems like the right thing to do. The alternative is to
use __maybe_unused, which is undesirable.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:11:
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:7:23: warning: ‘qcom_compressed_supported_formats’ defined but not used [-Wunused-const-variable=]
7 | static const uint32_t qcom_compressed_supported_formats[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:48:23: warning: ‘plane_formats_yuv’ defined but not used [-Wunused-const-variable=]
48 | static const uint32_t plane_formats_yuv[] = {
| ^~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:17:23: warning: ‘plane_formats’ defined but not used [-Wunused-const-variable=]
17 | static const uint32_t plane_formats[] = {
| ^~~~~~~~~~~~~
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:124:19: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:124:19: note: (near initialization for ‘sm8250_dpu_caps.max_linewidth’)
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'fmt' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'a' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'r' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'g' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'b' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e0' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e1' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e2' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e3' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'uc' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'alpha' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'bp' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'flg' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'fm' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'np' not described in 'INTERLEAVED_RGB_FMT'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Fritz Koenig <frkoenig@google.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_blk.c:28: warning: Function parameter or member 'hw_blk' not described in 'dpu_hw_blk_init'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_blk.c:120: warning: Excess function parameter 'free_blk' description in 'dpu_hw_blk_put'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:31: warning: Enum value 'DPU_PERF_MODE_MAX' not described in enum 'dpu_perf_mode'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:34: warning: Cannot understand * @_dpu_core_perf_calc_bw() - to calculate BW per crtc
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'kms' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'crtc' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'state' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:249: warning: Cannot understand * @dpu_core_perf_crtc_release_bw() - request zero bandwidth
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'ctl' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'pipeline' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'enabled' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Excess function parameter 'enable' description in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'ctl' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'pipeline' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'flush_mask' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'start' not described in 'mdp5_ctl_commit'
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c: In function ‘dpu_encoder_virt_mode_set’:
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:981:31: warning: variable ‘num_dspp’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:976:30: warning: variable ‘topology’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c: In function ‘_dpu_encoder_virt_enable_helper’:
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1099:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c: In function ‘dpu_encoder_virt_disable’:
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1210:18: warning: variable ‘dpu_kms’ set but not used [-Wunused-but-set-variable]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c: In function ‘_dpu_core_perf_calc_crtc’:
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:113:25: warning: variable ‘dpu_cstate’ set but not used [-Wunused-but-set-variable]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c:299:5: warning: no previous prototype for ‘mdp5_disable’ [-Wmissing-prototypes]
drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c:319:5: warning: no previous prototype for ‘mdp5_enable’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c:581:5: warning: no previous prototype for ‘mdp5_crtc_setup_pipeline’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/adreno/a6xx_gpu.c:33:6: warning: no previous prototype for ‘a6xx_idle’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In situations where the GPU is mostly idle, all or nearly all buffer
objects will be in the inactive list. But if the system is under memory
pressure (from something other than GPU), we could still get a lot of
shrinker calls. Which results in traversing a list of thousands of objs
and in the end finding nothing to shrink. Which isn't so efficient.
Instead split the inactive_list into two lists, one inactive objs which
are shrinkable, and a second one for those that are not. This way we
can avoid traversing objs which we know are not shrinker candidates.
v2: Fix inverted logic think-o
Signed-off-by: Rob Clark <robdclark@chromium.org>
Previously we only held obj lock in the _active_get() path, and relied
on atomic_dec_return() to not be racy in the _active_put() path where
obj lock was not held.
But this is a false sense of security. Unlike obj lifetime refcnt,
where you do not expect to *increase* the refcnt after the last put
(which would mean that something has gone horribly wrong with the
object liveness reference counting), the active_count can increase
again from zero. Racing _active_put()s and _active_get()s could leave
the obj on the wrong mm list.
But in the retire path, immediately after the _active_put(), the
_unpin_iova() would acquire obj lock. So just move the locking earlier
and rely on that to protect obj->active_count.
Fixes: c5c1643cef ("drm/msm: Drop struct_mutex from the retire path")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the new vma_set_file() function to allow changing
vma->vm_file with the necessary refcount dance.
v2: add more users of this.
v3: add missing EXPORT_SYMBOL, rebase on mmap cleanup,
add comments why we drop the reference on two occasions.
v4: make it clear that changing an anonymous vma is illegal.
v5: move vma_set_file to mm/util.c
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://patchwork.freedesktop.org/patch/399360/
For sinks that do not support audio, there is no need to notify
audio subsystem of the connection event.
This will make sure that audio routes only to the primary display
when connected to such sinks.
changes in v2:
- Added fixes tag
- Removed nested if condition and removed usage of global pointer
Fixes: d13e36d7d2 ("drm/msm/dp: add audio support for Display Port on MSM")
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some dongles require link training done at irq_hpd request instead
of plugin request. This patch promote irq_hpd handler to handle link
training and setup hpd_state correctly.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some dongle will not clear LINK_STATUS_UPDATED bit after
DPCD read which cause link training failed. This patch
just read 6 bytes of DPCD link status from sink and return
without checking LINK_STATUS_UPDATED bit.
Only 8 bits are used to represent link rate at sinker DPCD.
The really link rate is 2.7Mb times the 8 bits value.
For example, 0x0A at DPCD is equal to 2.7Gb (10 * 2.7Mb).
This patch also convert 8 bits value of DPCD to really link
rate to fix worng link rate error during phy compliance test.
Fixes: 6625e2637d ("drm/msm/dp: DisplayPort PHY compliance tests fixup")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
DP compo phy have to be enable to start link training. When
link training failed phy need to be disabled so that next
link traning can be proceed smoothly at next plug in. This
patch de-initialize mainlink to disable phy if link training
failed. This prevent system crash due to
disp_cc_mdss_dp_link_intf_clk stuck at "off" state. This patch
also perform checking power_on flag at dp_display_enable() and
dp_display_disable() to avoid crashing when unplug cable while
display is off.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Connection state is not set correctly happen when either failure of link
train due to cable unplugged in the middle of aux channel reading or
cable plugged in while in suspended state. This patch fixes these problems.
This patch also replace ST_SUSPEND_PENDING with ST_DISPLAY_OFF.
Changes in V2:
-- Add more information to commit message.
Changes in V3:
-- change base
Changes in V4:
-- add Fixes tag
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
During suspend, dp host controller and hpd block are disabled due to
both ahb and aux clock are disabled. Therefore hpd plug/unplug interrupts
will not be generated. At dp_pm_resume(), reinitialize both dp host
controller and hpd block so that hpd plug/unplug interrupts will be
generated and handled by driver so that hpd connection state is updated
correctly. This patch will fix link training flaky issues.
Changes in v2:
-- use container_of to cast correct dp_display_private pointer
at both dp_pm_suspend() and dp_pm_resume().
Changes in v3:
-- replace hpd_state atomic_t with u32
Changes in v4
-- call dp_display_host_deinit() at dp_pm_suspend()
-- call dp_display_host_init() at msm_dp_display_enable()
-- fix phy->init_count unbalance which causes link training failed
Changes in v5
-- add Fixes tag
Fixes: 8ede2ecc3e (drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets)
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Similar to the previous patch, clear shadow on suspend to avoid timeouts
waiting for ringbuffer space.
Fixes: 8907afb476 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clear the shadow rptr on suspend. Otherwise, when we resume, we can
have a stale value until CP_WHERE_AM_I executes. If we suspend near
the ringbuffer wraparound point, this can lead to a chicken/egg
situation where we are waiting for ringbuffer space to write the
CP_WHERE_AM_I (or CP_INIT) packet, because we mistakenly believe that
the ringbuffer is full (due to stale rptr value in the shadow).
Fixes errors like:
[drm:adreno_wait_ring [msm]] *ERROR* timeout waiting for space in ringbuffer 0
in the resume path.
Fixes: d3a569fccf ("drm/msm: a6xx: Use WHERE_AM_I for eligible targets")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Only the following drivers aren't converted:
- amdgpu, because of the driver_feature mangling due to virt support.
Subsequent patch will address this.
- nouveau, because DRIVER_ATOMIC uapi is still not the default on the
platforms where it's supported (i.e. again driver_feature mangling)
- vc4, again because of driver_feature mangling
- qxl, because the ioctl table is somewhere else and moving that is
maybe a bit too much, hence the num_ioctls assignment prevents a
const driver structure.
- arcpgu, because that is stuck behind a pending tiny-fication series
from me.
- legacy drivers, because legacy requires non-const drm_driver.
Note that for armada I also went ahead and made the ioctl array const.
Only cc'ing the driver people who've not been converted (everyone else
is way too much).
v2: Fix one misplaced const static, should be static const (0day)
v3:
- Improve commit message (Sam)
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: kernel test robot <lkp@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201104100425.1922351-5-daniel.vetter@ffwll.ch
Register GPU as a devfreq cooling device so that it can be passively
cooled by the thermal framework.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The kernel test robot is not happy with that.
This reverts commit 2b5b95b1ff.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/394773/
Add the new vma_set_file() function to allow changing
vma->vm_file with the necessary refcount dance.
v2: add more users of this.
v3: add missing EXPORT_SYMBOL, rebase on mmap cleanup,
add comments why we drop the reference on two occasions.
v4: make it clear that changing an anonymous vma is illegal.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/394773/
Now that the inactive_list is protected by mm_lock, and everything
else on per-obj basis is protected by obj->resv, we no longer depend
on struct_mutex.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The obj->lock is sufficient for what we need.
This *does* have the implication that userspace can try to shoot
themselves in the foot by racing madvise(DONTNEED) with submit. But
the result will be about the same if they did madvise(DONTNEED) before
the submit ioctl, ie. they might not get want they want if they race
with shrinker. But iova fault handling is robust enough, so userspace
is only shooting it's own foot.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that we don't need struct_mutex in the free path, we can get rid of
the asynchronous free altogether.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that active_list/inactive_list is protected by mm_lock, we no longer
need dev->struct_mutex in the free_object() path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that we are not relying on dev->struct_mutex to protect the
ring->submits lists, drop the struct_mutex lock.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
It cannot be atomically updated with obj->active_count, and the only
purpose is a useless WARN_ON() (which becomes a buggy WARN_ON() once
retire_submits() is not serialized with incoming submits via
struct_mutex)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before we remove dev->struct_mutex from the retire path, we have to deal
with the situation of a submit retiring before the submit ioctl returns.
To deal with this, ring->submits will hold a reference to the submit,
which is dropped when the submit is retired. And the submit ioctl path
holds it's own ref, which it drops when it is done with the submit.
Also, add to submit list *after* getting/pinning bo's, to prevent badness
in case the completed fence is corrupted, and retire_worker mistakenly
believes the submit is done too early.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
One less place to rely on dev->struct_mutex.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before adding another lock, give ring->lock a more descriptive name.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Rather than relying on the big dev->struct_mutex hammer, introduce a
more specific lock for protecting the bo lists.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Small cleanup, update_fences() is used in the hangcheck path, but also
in the normal retire path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
It is somewhat redundant with the gpu tracepoints, and anyways not too
useful to justify spamming the log when debug traces are enabled.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We only want to use the _unlocked() variant in the unlocked case.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This also converts the special msm_gem_get_vaddr_active() to expect the
lock to already be held. There are two call-sites for this, one already
has the lock held, so it is more straightforward to just open-code the
locking for the other caller.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unfortunately, due to an dev_pm_opp locking interaction with
mm->mmap_sem, we need to do pm get before aquiring obj locks,
otherwise we can have anger lockdep with the chain:
opp_table_lock --> &mm->mmap_sem --> reservation_ww_class_mutex
For an explicit fencing userspace, the impact should be minimal
as we do all the fence waits before this point. It could result
in some needless resumes in error cases, etc.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We cannot switch to using obj->resv for locking without first moving all
the copy_from_user() ahead of submit_lock_objects(). Otherwise in the
mm fault path we aquire mm->mmap_sem before obj lock, but in the submit
path the order is reversed.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move grabbing the bo lock into shrinker, with a msm_gem_trylock() to
skip over bo's that are already locked. This gets rid of the nested
lock classes.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When we cut-over to using dma_resv_lock/etc instead of msm_obj->lock,
we'll need these for the submit path (where resv->lock is already held).
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We'll need to introduce a _locked() version of msm_gem_get_iova(), so we
need to make that name available.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This will make it easier to transition over to obj->resv locking for
everything that is per-bo locking.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The microcode bo's should never be madvise(WONTNEED), so these should
not be using msm_gem_get_vaddr_active().
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reading VCO rate for this PLL can cause boot stalls, if it is not
enabled. Guard clk_hw_get_rate with a call to
dsi_pll_28nm_clk_is_enabled().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The dev_pm_opp_of_add_table() api initializes the icc nodes for gpu
indirectly. So we can avoid using of_icc_get() api in the common
probe path. To improve this, move of_icc_get() to target specific code
where it is required.
This patch helps to fix duplicate gpu node listed in the interconnect
summary from the debugfs.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
c33b7c0389 ("drm/msm/dpu: add support for clk and bw scaling for
display") has added support for handling bandwidth voting in kms path in
addition to old mdss path. However this broke all other platforms since
_dpu_core_perf_crtc_update_bus() will now error out instead of properly
calculating bandwidth and core clocks. Fix
_dpu_core_perf_crtc_update_bus() to just skip bandwidth setting instead
of returning an error in case kms->num_paths == 0 (MDSS is used for
bandwidth management).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c33b7c0389 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Handle new merge_3d block setup in dpu encoder code. Pass correct mode
and id. Note, that merge_3d blocks are not handled via usual RM
reservation mechanism, as each merge_3d block is tied to two PPs, so by
reserving PP you get merge_3d automatically.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Handle setting up merge mode in merge_3d hardware block.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Active HW CTL blocks need separate handling for merge_3d flushes.
Implement necessary merge_3d configuration and flushing.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add initial support for merge3D hardware block on SM8[12]50. Merge3D is
reposible for merging contents of two LMs (two PPs) into single
interface.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of calling 4 callbacks to set pending masks, call just one to
update both pending_flush_mask and pending_intf_flush mask. Note, that
CMD mode support incorrectly did not update pending_intf_flush mask,
breaking CMD support on SC7180/SM8x50.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement the shutdown callback for adreno gpu platform device
to safely shutdown it before a system reboot. This helps to avoid
futher transactions from gpu after the smmu is moved to bypass mode.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Set link rate by using OPP set rate api so that CX level will be set
accordingly based on the link rate.
Changes in v2:
-- remove dev from dp_ctrl_put() parameters
-- Add more information to commit message
Changes in v3:
-- return when dev_pm_opp_set_clkname() failed
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
clk_prepare_enable() and clk_disable_unprepare() will check
NULL clock parameter, so It is not necessary to add additional checks.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ff73ff1940 ("drm/msm/dsi: Populate the 10nm PHY funcs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Rob Clark <robdclark@chromium.org>
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c6659785df ("drm/msm/dsi/pll: call vco set rate explicitly")
Signed-off-by: Rob Clark <robdclark@chromium.org>
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Bandwidth code was being used as test link rate. Fix this by converting
bandwidth code to test link rate
Do not reset voltage and pre-emphasis level during IRQ HPD attention
interrupt. Also fix pre-emphasis parsing during test link status process
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
DRM_MSM fails to build with DRM_MSM_DP=n; add the missing stub.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, also create a label to put clkname.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use a SCHED_FIFO kthread_worker for async atomic commits. We have a
hard deadline if we don't want to miss a frame.
Signed-off-by: Rob Clark <robdclark@chromium.org>
lockdep dislikes seeing locks unwound in a non-nested fashion.
Fixes: b3d91800d9 ("drm/msm: Fix race condition in msm driver with async layer updates")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
When there are back to back commits with async cursor update,
there is a case where second commit can program the DPU hw
blocks while first didn't complete flushing config to HW.
Synchronize the compositions such that second commit waits
until first commit flushes the composition.
This change also introduces per crtc commit lock, such that
commits on different crtcs are not blocked by each other.
Changes in v2:
- Use an array of mutexes in kms to handle commit
lock per crtc. (Rob Clark)
Changes in v3:
- Add wrapper functions to handle lock and unlock of
commit_lock for each crtc. (Rob Clark)
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl+IiPwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYPKEQ//TM8vxjucnRl/pklpMin49dJorwiVvROLhQqLmdxw
286ZKpVzYYAPc7LnNqwIBugnFZiXuHu8xPKQkIiOa2OtNDTwhKNoBxOAmOJaV6DD
8JfEtZYeX5mKJ/Nqd2iSkIqOvCwZ9Wzii+aytJ2U88wezQr1fnyF4X49MegETEey
FHWreSaRWZKa0MMRu9AQ0QxmoNTHAQUNaPc0PeqEtPULybfkGOGw4/ghSB7WcKrA
gtKTuooNOSpVEHkTas2TMpcBp6lxtOjFqKzVN0ml+/nqq5NeTSDx91VOCX/6Cj76
mXIg+s7fbACTk/BmkkwAkd0QEw4fo4tyD6Bep/5QNhvEoAriTuSRbhvLdOwFz0EF
vhkF0Rer6umdhSK7nPd7SBqn8kAnP4vBbdmB68+nc3lmkqysLyE4VkgkdH/IYYQI
6TJ0oilXWFmU6DT5Rm4FBqCvfcEfU2dUIHJr5wZHqrF2kLzoZ+mpg42fADoG4GuI
D/oOsz7soeaRe3eYfWybC0omGR6YYPozZJ9lsfftcElmwSsFrmPsbO1DM5IBkj1B
gItmEbOB9ZK3RhIK55T/3u1UWY3Uc/RVr+kchWvADGrWnRQnW0kxYIqDgiOytLFi
JZNH8uHpJIwzoJAv6XXSPyEUBwXTG+zK37Ce769HGbUEaUrE71MxBbQAQsK8mDpg
7fM=
=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
Split out all the bits that are purely for dma_map_ops implementations
and related code into a new <linux/dma-map-ops.h> header so that they
don't get pulled into all the drivers. That also means the architecture
specific <asm/dma-mapping.h> is not pulled in by <linux/dma-mapping.h>
any more, which leads to a missing includes that were pulled in by the
x86 or arm versions in a few not overly portable drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
* DSI support for sm8150/sm8250
* Support for per-process GPU pagetables (finally!) for a6xx.
There are still some iommu/arm-smmu changes required to
enable, without which it will fallback to the current single
pgtable state. The first part (ie. what doesn't depend on
drm side patches) is queued up for v5.10[1].
* DisplayPort support. Userspace DP compliance tool support
is already merged in IGT[2]
* The usual assortment of smaller fixes/cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvqjuzH=Po_9EzzFsp2Xq3tqJUTKfsA2g09XY7_+6Ypfw@mail.gmail.com
Fix the incorrect function prototype for dp_debug_get()
in the dp_debug module to address compilation warning.
Also add prototype for msm_dp_debugfs_init() for fixing compilation
issue with other defconfigs.
changes in v2:
- add prototype for msm_dp_debugfs_init()
Fixes: f913454aae ("drm/msm/dp: move debugfs node to /sys/kernel/debug/dri/*/")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
GEM object functions deprecate several similar callback interfaces in
struct drm_driver. This patch replaces the per-driver callbacks with
per-instance callbacks in msm. The only exception is gem_prime_mmap,
which is non-trivial to convert.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923102159.24084-10-tzimmermann@suse.de
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX2jGxQAKCRDj7w1vZxhR
xR3DAQCiZOnaxVcY49iG4343Z1aHHaIEShbnB0bDdaWstn7kiQD/UXBXUoOSFoFQ
FkTsW31JsdXNnWP5e6/eJd2Lb6waVAA=
=VlsU
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-09-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.10:
UAPI Changes:
Cross-subsystem Changes:
- virtio: Merged a PR for patches that will affect drm/virtio
Core Changes:
- dev: More devm_drm convertions and removal of drm_dev_init
- atomic: Split out drm_atomic_helper_calc_timestamping_constants of
drm_atomic_helper_update_legacy_modeset_state
- ttm: More rework
Driver Changes:
- i915: selftests improvements
- panfrost: support for Amlogic SoC
- vc4: one fix
- tree-wide: conversions to devm_drm_dev_alloc,
- ast: simplifications of the atomic modesetting code
- panfrost: multiple fixes
- vc4: multiple fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921152956.2gxnsdgxmwhvjyut@gilmour.lan
We found two unused variables new_cnt and old_cnt when build kernel with
W=1.
So delete it.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Leave the inuse count intact on map failure to keep the accounting
accurate.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the case where we have a back-to-back submission that shares the same
BO, this BO will be prematurely moved to inactive_list while retiring the
first submit. But it will be still part of the second submit which is
being processed by the GPU. Now, if the shrinker happens to be triggered at
this point, it will result in a premature purging of this BO.
To fix this, we need to refcount BO while doing submit and retire. Then,
it should be moved to inactive list when this refcount becomes 0.
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The dependency on interconnect in the Kconfig was introduced to avoid
the case of interconnect=m and driver=y, but the interconnect framework
has been converted from tristate to bool now. Remove the dependency as
the framework can't be a module anymore.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Commit 604234f336 ("drm/msm: Enable expanded apriv support for a650")
was checking the result of adreno_is_a650() before the gpu revision
got probed in adreno_gpu_init() so it was always coming across as
false. Snoop into the revision ID ahead of time to correctly set the
hw_apriv flag so that it can be used by msm_gpu to properly setup
global buffers.
Fixes: 604234f336 ("drm/msm: Enable expanded apriv support for a650")
Reported-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Tested-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We shouldn't be waiting for an event here with a timeout of 100ms when
we're not in the 'timeout' arm of the if condition. Instead we should be
sleeping in the interruptible state (S) until something happens and we
need to wakeup. Right now this kthread is running almost all the time
because it sleeps for 100ms, wakes up, sees there's nothing to do, and
then starts the process all over again. Looking at top it shows up in
the D state (uninterruptible) because it uses wait_event_timeout(). FIx
this up.
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Reported-by: Douglas Anderson <dianders@chromium.org>
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Please pull a set of fixes for various DRM drivers that finally resolve
incorrect usage of the scatterlists (struct sg_table nents and orig_nents
entries), what causes issues when IOMMU is used.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910080505.24456-1-m.szyprowski@samsung.com
Make the necessary changes to the DP driver to use the qmp phy from the
common phy framework instead of rolling our own in the drm subsystem.
This also removes the PLL code and adds proper includes so things build.
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
No need to fix the number of resolutions to one during the video
pattern CTS test. The userspace test client will handle both
the hotplug as well as picking the right resolution for the test.
Changes in v2: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the debugfs nodes needed for the video pattern
compliance tests to MSM DP driver.
Changes in v2: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move the MSM DP debugfs node from /sys/kernel/debug/drm_dp
to /sys/kernel/debug/dri/*/ as required for video pattern
compliance test suite.
Changes in v2: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
To prepare the MSM DP driver for running video pattern
compliance tests introduce debugfs module for it.
Changes in v2: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the current implementation, there is a very small window for
the audio side to safely signal the hdmi_code_shutdown() before
the clocks are disabled.
Add some synchronization between the DP display and DP audio module
to safely disable the clocks to avoid unclocked access from audio
side.
In addition, audio side can open the sound card even if DP monitor
is not connected. Avoid programming hardware registers in this case
and bail out early.
Changes in v4:
- removed some leftover prints
Changes in v5:
- fix crash when user tries to play audio in suspended
state
Changes in v6:
- rebased on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signal the hotplug disconnect event to the audio side in the
event handler so that they are notified earlier and have more
time to process the disconnect event.
Changes in v2: none
Changes in v3: none
Changes in v4: rebase on top of latest patchset of dependency
Changes in v5: rebase on top of latest patchset of dependency
Changes in v6: none
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the hook_plugged_cb op for the MSM DP driver to signal connect
and disconnect events to the hdmi-codec driver which in-turn shall
notify the audio subsystem to start a new or teardown an existing
session.
Changes in v2: none
Changes in v3: none
Changes in v4: rebase on top of latest patchset of dependency
Changes in v5: rebase on top of latest patchset of dependency
Changes in v6: none
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce audio support for Display Port on MSM chipsets.
This change integrates DP audio sub-module with the main
Display Port platform driver.
In addition, this change leverages hdmi_codec_ops to expose
the operations to the audio driver.
Changes in v2: fix up a compilation issue on drm-next branch
Changes in v3: none
Changes in v4: none
Changes in v5: none
Changes in v6: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Store the dp_display in the platform driver data instead of the
dp_display_private.
This is required to allow other sub-modules to reuse the platform
driver data.
Changes in v3: none
Changes in v4: none
Changes in v5: none
Changes in v6: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
add event thread to execute events serially from event queue. Also
timeout mode is supported which allow an event be deferred to be
executed at later time. Both link and phy compliant tests had been
done successfully.
Changes in v2:
-- Fix potential deadlock by removing redundant connect_mutex
-- Check and enable link clock during modeset
-- Drop unused code and fix function prototypes.
-- set sink power to normal operation state (D0) before DPCD read
Changes in v3:
-- push idle pattern at main link before timing generator off
-- add timeout handles for both connect and disconnect
Changes in v4:
-- add ST_SUSPEND_PENDING to handles suspend/modeset test operations
-- clear dp phy aux interrupt status when ERR_DPPHY_AUX error
-- send segment addr during edid read
-- clear bpp depth before MISC register write
Changes in v5:
-- add ST_SUSPENDED to fix crash at resume
Changes in v6:
-- at msm_dp_display_enable() do not return until resume_done to avoid
kms commit timeout
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Configure HPD registers in DP controller and
enable HPD interrupt.
Add interrupt to handle HPD connect and disconnect events.
Changes in v8: None
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add display port support in DPU by creating hooks
for DP encoder enumeration and encoder mode
initialization.
changes in v2:
- rebase on [2] (Sean Paul)
- remove unwanted error checks and
switch cases (Jordan Crouse)
[1] https://lwn.net/Articles/768265/
[2] https://lkml.org/lkml/2018/11/17/87
changes in V3:
-- Moved this change as part of the DP driver changes.
-- Addressed compilation issues on the latest code base.
Changes in v6:
-- Fix checkpatch.pl warning
Changes in v7: Remove depends-on tag from commit message.
Changes in v8: None
Changes in v9: None
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the needed DP PLL specific files to support
display port interface on msm targets.
The DP driver calls the DP PLL driver registration.
The DP driver sets the link and pixel clock sources.
Changes in v2:
-- Update copyright markings on all relevant files.
-- Use DRM_DEBUG_DP for debug msgs.
Changes in v4:
-- Update the DP link clock provider names
Changes in V5:
-- Addressed comments from Stephen Boyd, Rob clark.
Changes in V6:
-- Remove PLL as separate driver and include PLL as DP module
-- Remove redundant clock parsing from PLL module and make DP as
clock provider
-- Map USB3 DPCOM and PHY IO using hardcoded register address and
move mapping form parser to PLL module
-- Access DP PHY modules from same base address using offsets instead of
deriving base address of individual module from device tree.
-- Remove dp_pll_10nm_util.c and include its functionality in
dp_pll_10nm.c
-- Introduce new data structures private to PLL module
Changes in v7:
-- Remove DRM_MSM_DP_PLL config from Makefile and Kconfig
-- Remove set_parent from determin_rate API
-- Remove phy_pll_vco_div_clk from parent list
-- Remove flag CLK_DIVIDER_ONE_BASED
-- Remove redundant cell-index property parsing
Changes in v8:
-- Unregister hardware clocks during driver cleanup
Changes in v9:
-- Remove redundant Kconfig option DRM_MSM_DP_10NM_PLL
Changes in v10:
-- Limit 10nm PLL function scope
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the needed displayPort files to enable DP driver
on msm target.
"dp_display" module is the main module that calls into
other sub-modules. "dp_drm" file represents the interface
between DRM framework and DP driver.
Changes in v12:
-- Add support of pm ops in display port driver
-- Clear bpp depth bits before writing to MISC register
-- Fix edid read
Previous Change log:
https://lkml.kernel.org/lkml/20200818051137.21478-3-tanmay@codeaurora.org/
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Co-developed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Co-developed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Co-developed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As newer GPU families are added it makes less sense to maintain a
"generic" version functions for older families. Move adreno_submit()
and get_rptr() into the target specific code for a2xx, a3xx and a4xx.
Add a parameter to adreno_flush to pass the target specific WPTR register
instead of relying on the generic register.
All of this gets rid of the last of the REG_ADRENO offsets so remove all
all the register definitions and infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Support the WHERE_AM_I opcode for the A618, A630 and A640 GPUs if the
microcode supports it. The WHERE_AM_I opcode allows the RPTR shadow
to be updated in priviliged memory which protects the shadow from being
read or written from user submissions.
A650 already supports extended APRIV have built in hardware support for
to access privilged memory from the CP and can go back to using the
hardware RPTR shadow feature.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Newer microcode versions have support for the CP_WHERE_AM_I opcode which
allows the RPTR shadow memory to be marked as privileged to protect it
from corruption. Move the RPTR shadow into its own buffer and protect it
it if the current microcode version supports the new feature.
We can also re-enable preemption for those targets that support
CP_WHERE_AM_I. Start out by preemptively assuming that we can enable
preemption and disable it in a5xx_hw_init if the microcode version comes
back as too old.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In $debugfs/gem we already show any vma(s) associated with an object.
Also show process names if the vma's address space is a per-process
address space.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for using per-instance pagetables if all the dependencies are
available.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Add support for allocating private address space instances. Targets that
support per-context pagetables should implement their own function to
allocate private address spaces.
The default will return a pointer to the global address space.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support to create a io-pgtable for use by targets that support
per-instance pagetables. In order to support per-instance pagetables the
GPU SMMU device needs to have the qcom,adreno-smmu compatible string and
split pagetables enabled.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the aperture settings from the IOMMU domain to set up the virtual
address range for the GPU. This allows us to transparently deal with
IOMMU side features (like split pagetables).
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that we can get the ctx from the submitqueue, the extra arg is
redundant.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[split out of previous patch to reduce churny noise]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Each submitqueue is attached to a context. Add a pointer to the
context to the submitqueue at create time and refcount it so
that it stays around through the life of the queue.
Co-developed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This will be populated by adreno-smmu, to provide a way for coordinating
enabling/disabling TTBR0 translation.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In a later patch, the drvdata will not directly be 'struct msm_gpu *',
so add a helper to reduce the churn.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently it doesn't matter, since we free the ctx immediately. But
when we start refcnt'ing the ctx, we don't want old dangling list
entries to hang around.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It's allocating an array of a6xx_gpu_state_obj structure rathor than
its pointers.
This patch fix it.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The function iommu_domain_alloc returns NULL on platforms without IOMMU
such as msm8974. This resulted in PTR_ERR(-ENODEV) being assigned to
gpu->aspace so the correct code path wasn't taken.
Fixes: ccac7ce373 ("drm/msm: Refactor address space initialization")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.
Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
This allows DSI driver to work with sm8150 and sm8250. The sdm845 config
is re-used as the config is the same.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
The clk_pre/clk_post values in shared_timings are used instead, and these
are unused.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The Documentation/DMA-API-HOWTO.txt states that the dma_map_sg() function
returns the number of the created entries in the DMA address space.
However the subsequent calls to the dma_sync_sg_for_{device,cpu}() and
dma_unmap_sg must be called with the original number of the entries
passed to the dma_map_sg().
struct sg_table is a common structure used for describing a non-contiguous
memory buffer, used commonly in the DRM and graphics subsystems. It
consists of a scatterlist with memory pages and DMA addresses (sgl entry),
as well as the number of scatterlist entries: CPU pages (orig_nents entry)
and DMA mapped pages (nents entry).
It turned out that it was a common mistake to misuse nents and orig_nents
entries, calling DMA-mapping functions with a wrong number of entries or
ignoring the number of mapped entries returned by the dma_map_sg()
function.
To avoid such issues, lets use a common dma-mapping wrappers operating
directly on the struct sg_table objects and use scatterlist page
iterators where possible. This, almost always, hides references to the
nents and orig_nents entries, making the code robust, easier to follow
and copy/paste safe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Rob Clark <robdclark@gmail.com>
This reduces the spam in dmesg when we start hitting the shrinker, and
replaces it with something we can put on a timeline while profiling or
debugging system issues.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Technically the GMU specific one is a bit redundant, but it was useful
to track down a bug.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
This function is called quite often if you have a blinking cursor on the
screen, hello page flip. Let's drop this debug print here because it
means enabling the print via the module parameter starts to spam the
debug console.
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The cstate->num_mixers member is only set to a non-zero value once
dpu_encoder_virt_mode_set() is called, but the atomic check function can
be called by userspace before that. Let's avoid the div-by-zero here and
inside _dpu_crtc_setup_lm_bounds() by skipping this part of the atomic
check if dpu_encoder_virt_mode_set() hasn't been called yet. This fixes
an UBSAN warning:
UBSAN: Undefined behaviour in drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:860:31
division by zero
CPU: 7 PID: 409 Comm: frecon Tainted: G S 5.4.31 #128
Hardware name: Google Trogdor (rev0) (DT)
Call trace:
dump_backtrace+0x0/0x14c
show_stack+0x20/0x2c
dump_stack+0xa0/0xd8
__ubsan_handle_divrem_overflow+0xec/0x110
dpu_crtc_atomic_check+0x97c/0x9d4
drm_atomic_helper_check_planes+0x160/0x1c8
drm_atomic_helper_check+0x54/0xbc
drm_atomic_check_only+0x6a8/0x880
drm_atomic_commit+0x20/0x5c
drm_atomic_helper_set_config+0x98/0xa0
drm_mode_setcrtc+0x308/0x5dc
drm_ioctl_kernel+0x9c/0x114
drm_ioctl+0x2ac/0x4b0
drm_compat_ioctl+0xe8/0x13c
__arm64_compat_sys_ioctl+0x184/0x324
el0_svc_common+0xa4/0x154
el0_svc_compat_handler+0x
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We could get a vblank event racing with the current atomic commit,
resulting in sending the pageflip event to userspace early, causing
tearing. On the other hand, complete_commit() ensures that the
pending flush is complete.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Add drm_device argument to drm_prime_pages_to_sg(), so we can
call dma_max_mapping_size() to figure the segment size limit
and call into __sg_alloc_table_from_pages() with the correct
limit.
This fixes virtio-gpu with sev. Possibly it'll fix other bugs
too given that drm seems to totaly ignore segment size limits
so far ...
v2: place max_segment in drm driver not gem object.
v3: move max_segment next to the other gem fields.
v4: just use dma_max_mapping_size().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20200907112425.15610-2-kraxel@redhat.com
Commit '6f6a73c8b715d595977774d48450a734297ab21f' from Linus' tree
The fixes reverts cause a bit of a conflict pain with intel next,
start fixing it up here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
A few fixes for a potential RPTR corruption issue.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGvnr6Nhz2J0sjv2G+j7iceVtaDiJDT8T88uW6jiBfOGKQ@mail.gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into drm-next
Backmerge 5.9-rc4 as there is a nasty qxl conflict
that needs to be resolved.
Signed-off-by: Dave Airlie <airlied@redhat.com>
XX_print like pfp_print/me_print/meq_print/roq_print are just
used in file a5xx_debugfs.c. And these function always return
0, this return value is meaningless.
This change is to make the code a bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that it isn't causing problems to use dma_map/unmap, we can drop the
hack of using dma_sync in certain cases.
Signed-off-by: Rob Clark <robdclark@chromium.org>
MSM bus scaling has moved on to use interconnect framework
and downstream bus scaling apis are not present anymore.
Remove them as they are nop anyways in the current code,
no functional change.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
MSM bus scaling has moved on to use interconnect framework
and downstream bus scaling apis are not present anymore.
Remove them as they are nop anyways in the current code,
no functional change.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to scale src clk and bandwidth as
per composition requirements.
Interconnect registration for bw has been moved to mdp
device node from mdss to facilitate the scaling.
Changes in v1:
- Address armv7 compilation issues with the patch (Rob)
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Disable the RPTR shadow across all targets. It will be selectively
re-enabled later for targets that need it.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
a650 supports expanded apriv support that allows us to map critical buffers
(ringbuffer and memstore) as as privileged to protect them from corruption.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The main a5xx preemption record can be marked as privileged to
protect it from user access but the counters storage needs to be
remain unprivileged. Split the buffers and mark the critical memory
as privileged.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
core:
- Take modeset bkl for legacy drivers.
dp_mst:
- Allow null crtc in dp_mst.
i915:
- Fix command parser desc matching with masks
amdgpu:
- Misc display fixes
- Backlight fixes
- MPO fix for DCN1
- Fixes for Sienna Cichlid
- Fixes for Navy Flounder
- Vega SW CTF fixes
- SMU fix for Raven
- Fix a possible overflow in INFO ioctl
- Gfx10 clockgating fix
msm:
- opp/bw scaling patch followup
- frequency restoring fux
- vblank in atomic commit fix
- dpu modesetting fixes
- fencing fix
etnaviv:
- scheduler interaction fix
- gpu init regression fix
exynos:
- Just drop __iommu annotation to fix sparse warning.
omap:
- locking state fix.
-----BEGIN PGP SIGNATURE-----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=ZmIT
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2020-08-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"As expected a bit of an rc3 uptick, amdgpu and msm are the main ones,
one msm patch was from the merge window, but had dependencies and we
dropped it until the other tree had landed. Otherwise it's a couple of
fixes for core, and etnaviv, and single i915, exynos, omap fixes.
I'm still tracking the Sandybridge gpu relocations issue, if we don't
see much movement I might just queue up the reverts. I'll talk to
Daniel next week once he's back from holidays.
core:
- Take modeset bkl for legacy drivers
dp_mst:
- Allow null crtc in dp_mst
i915:
- Fix command parser desc matching with masks
amdgpu:
- Misc display fixes
- Backlight fixes
- MPO fix for DCN1
- Fixes for Sienna Cichlid
- Fixes for Navy Flounder
- Vega SW CTF fixes
- SMU fix for Raven
- Fix a possible overflow in INFO ioctl
- Gfx10 clockgating fix
msm:
- opp/bw scaling patch followup
- frequency restoring fux
- vblank in atomic commit fix
- dpu modesetting fixes
- fencing fix
etnaviv:
- scheduler interaction fix
- gpu init regression fix
exynos:
- Just drop __iommu annotation to fix sparse warning
omap:
- locking state fix"
* tag 'drm-fixes-2020-08-28' of git://anongit.freedesktop.org/drm/drm: (41 commits)
drm/amd/display: Fix memleak in amdgpu_dm_mode_config_init
drm/amdgpu: disable runtime pm for navy_flounder
drm/amd/display: Retry AUX write when fail occurs
drm/amdgpu: Fix buffer overflow in INFO ioctl
drm/amd/powerplay: Fix hardmins not being sent to SMU for RV
drm/amdgpu: use MODE1 reset for navy_flounder by default
drm/amd/pm: correct the thermal alert temperature limit settings
drm/amdgpu: add asd fw check before loading asd
drm/amd/display: Keep current gain when ABM disable immediately
drm/amd/display: Fix passive dongle mistaken as active dongle in EDID emulation
drm/amd/display: Revert HDCP disable sequence change
drm/amd/display: Send DISPLAY_OFF after power down on boot
drm/amdgpu/gfx10: refine mgcg setting
drm/amd/pm: correct Vega20 swctf limit setting
drm/amd/pm: correct Vega12 swctf limit setting
drm/amd/pm: correct Vega10 swctf limit setting
drm/amd/pm: set VCN pg per instances
drm/amd/pm: enable run_btc callback for sienna_cichlid
drivers: gpu: amd: Initialize amdgpu_dm_backlight_caps object to 0 in amdgpu_dm_update_backlight_caps
drm/amd/display: Reject overlay plane configurations in multi-display scenarios
...
The patch reorganizing the set_freq function made it so the gmu resume
doesn't always set the frequency, because a6xx_gmu_set_freq() exits early
when the frequency hasn't been changed. Note this always happens when
resuming GMU after recovering from a hang.
Use a simple workaround to prevent this from happening.
Fixes: 1f60d11423 ("drm: msm: a6xx: send opp instead of a frequency")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
For production devices, the debugbus sections will typically be fused
off and empty in the gpu device coredump. But since this may contain
data like cache contents, don't capture it by default.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Backport note: maybe wait some time for the crashdec MR[1] to look for
both the old typo'd name and the corrected name to land in mesa 20.2
[1] https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/6242
Fixes: 1707add815 ("drm/msm/a6xx: Add a6xx gpu state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
New Qualcomm firmware has changed a way it reports back the 'started'
event. Support new register values.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This has roughly the same effect as drm_atomic_helper_wait_for_vblanks(),
basically just ensuring that vblank accounting is enabled so that we get
valid timestamp/seqn on pageflip events.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Define shutdown callback for display drm driver,
so as to disable all the CRTCS when shutdown
notification is received by the driver.
This change will turn off the timing engine so
that no display transactions are requested
while mmu translations are getting disabled
during reboot sequence.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Changes in v2:
- Remove NULL check from msm_pdev_shutdown (Stephen Boyd)
- Change commit text to reflect when this issue
was uncovered (Sai Prakash Ranjan)
Signed-off-by: Rob Clark <robdclark@chromium.org>
This patches replaces the previously used static DDR vote and uses
dev_pm_opp_set_bw() to scale GPU->DDR bandwidth along with scaling
GPU frequency. Also since the icc path voting is handled completely
in the opp driver, remove the icc_path handle and its usage in the
drm driver.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GPU has no business writing into the ringbuffer, let's make it
readonly to the GPU.
Fixes: 7198e6b031 ("drm/msm: add a3xx gpu support")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We need to set it to the most recent completed fence, not the most
recent submitted. Otherwise we have races where we think we can retire
submits that the GPU is not finished with, if the GPU doesn't manage to
overwrite the seqno before we look at it.
This can show up with hang recovery if one of the submits after the
crashing submit also hangs after it is replayed.
Fixes: f97decac5f ("drm/msm: Support multiple ringbuffers")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:817 dpu_crtc_enable() error: uninitialized symbol 'request_bandwidth'.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Plane validation uses an API drm_calc_scale which will
return src/dst value as a scale ratio.
when viewing the range on a scale the values should fall in as
Upscale ratio < Unity scale < Downscale ratio for src/dst formula
Fix the min and max scale ratios to suit the API accordingly.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Kristian H. Kristensen <hoegsberg@google.com>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In TEST_ONLY commit, rm global_state will duplicate the
object and request for new reservations, once they pass
then the new state will be swapped with the old and will
be available for the Atomic Commit.
This patch fixes some of missing links in the resource
reservation sequence mentioned above.
1) Creation of duplicate state in test_only commit (Rob)
2) Allocate and release the resources on every modeset.
3) Avoid allocation only when active is false.
In a modeset operation, swap state happens well before
disable. Hence clearing reservations in disable will
cause failures in modeset enable.
Allow reservations to be cleared/allocated before swap,
such that only newly committed resources are pushed to HW.
Changes in v1:
- Move the rm release to atomic_check.
- Ensure resource allocation and free happens when active
is not changed i.e only when mode is changed.(Rob)
Changes in v2:
- Handle dpu_kms_get_global_state API failure as it may
return EDEADLK (swboyd).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
These functions are now empty and no longer
useful so remove the functions and their uses.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Bernard Zhao <bernard@vivo.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>,
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Icenowy Zheng <icenowy@aosc.io>,
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: dri-devel@lists.freedesktop.org,
Cc: linux-kernel@vger.kernel.org
Cc: opensource.kernel@vivo.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # Fixed build and a few warnings
Link: https://patchwork.freedesktop.org/patch/msgid/9e13761020750b1ce2f1fabee23ef6e2a2942882.camel@perches.com
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
Use kthread_create_worker to simplify the code and optimise
the manager struct: msm_drm_thread. With this change, we
could remove struct element (struct task_struct *thread &
struct kthread_worker worker), instead, use one point (struct
kthread_worker *worker).
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This commit adds support for the MDP5 IP on Snapdragon
636/660.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This also applies to sdm630/636 and their SDA
counterparts.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This commit adds support for the MDP5 IP on Snapdragon
630. The configuration is different from SDM660's, as
the latter one has two DSI outputs.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
These SoCs make use of the 14nm phy, but at different
addresses than other 14nm units.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Initialize hardware clock-gating registers on A640 and A650 GPUs.
At least for A650, this solves some performance issues.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This will allow supporting different hwcg tables for a6xx.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This brings up basic video mode functionality for SM8250 DPU. Command mode
and dual mixer/intf configurations are not working, future patches will
address this. Scaler functionality and multiple planes is also untested.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This brings up basic video mode functionality for SM8150 DPU. Command mode
and dual mixer/intf configurations are not working, future patches will
address this. Scaler functionality and multiple planes is also untested.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[fixup max_linewidth warning]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Calculate the correct timings for displayport, from downstream driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This fixes flushing of INTF_2 and INTF_3 on SM8150 and SM8250 hardware.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The INTF_INPUT_CTRL feature is not available on sdm845, so don't set it.
This also adds separate feature bits for INTF (based on downstream) instead
of using CTL feature bit for it, and removes the unnecessary NULL check in
the added bind_pingpong_blk function.
Fixes: 73bfb790ac ("msm:disp:dpu1: setup display datapath for SC7180 target")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This isn't something that ever changes between planes, so move it to
dpu_caps struct. Making this change will allow more re-use in the
"SSPP sub blocks config" part of the catalog, in particular when adding
support for SM8150 and SM8250 which have different max_linewidth.
This also sets max_hdeci_exp/max_vdeci_exp to 0 for sc7180, as decimation
is not supported on the newest DPU versions. (note that decimation is not
implemented, so this changes nothing)
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Update the UBWC registers to the right values for sm8150 and sm8250.
This removes broken dpu_hw_reset_ubwc, which doesn't work because the
"force blk offset to zero to access beginning of register region" hack is
copied from downstream, where mapped region starts 0x1000 below what is
used in the upstream driver.
Also simplifies the overly complicated change that was introduced in
e4f9bbe9f8 to work around dpu_hw_reset_ubwc being broken.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
All DPU versions starting from 4.0 use the sdm845 version, so check for
that instead of checking each version individually. This chooses the right
function for sm8150 and sm8250.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This is required for A640 and A650 to be able to share UBWC-compressed
images with other HW such as display, which expect this configuration.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Small cleanup, lets not open-code bits/bitfields that are properly
defined in the rnndb xml (and therefore have builders in the generated
headers)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We haven't sync'd for a while.. pull in updates to get definitions for
some fields in pkt7 payloads.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This sets up bw tables for A640/A650 similar to A618/A630, 0 DDR bandwidth
vote, and the CNOC vote. A640 has the same CNOC addresses as A630 and was
working, but this is required for A650 to work.
Eventually the bw table should be filled by querying the interconnect
driver for each BW in the dts, but use these dummy tables for now.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
A650 has a separate RSCC region, so dump RSCC registers separately, reading
them from the RSCC base. Without this change a GPU hang will cause a system
reset if CONFIG_DEV_COREDUMP is enabled.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We don't expect to find vbif_nrt or regdma on sdm845, but were clogging
up dmesg with errors about it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
If split-lm is used (for ex, on sdm845), we can have multiple ping-
pongs, but only a single phys encoder. We need to configure dithering
on each of them.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On targets where GMU is available, GMU takes over the ownership of GX GDSC
during its initialization. So, move the refcount-get on GX PD before we
initialize the GMU. This ensures that nobody can collapse the GX GDSC
once GMU owns the GX GDSC. This patch fixes some GMU OOB errors seen
during GPU wake up during a system resume.
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On some qualcomm platforms DPU needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This can happen a lot when things go pear shaped. Lets not flood dmesg
when this happens.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This patch changes the plumbing to send the devfreq recommended opp rather
than the frequency. Also consolidate and rearrange the code in a6xx to set
the GPU frequency and the icc vote in preparation for the upcoming
changes for GPU->DDR scaling votes.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change enables dither block for primary interface
in display.
Enabled for 6bpc in the current version.
Changes in v1:
- Remove redundant error checks (Rob).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
If there is no interconnect-names, but there is an interconnects
property, then of_icc_get(dev, "gfx-mem"); would return an error
rather than NULL.
Also, if there is no interconnect-names property, there will never
be a ocmem path. But of_icc_get(dev, "ocmem") would return -EINVAL
instead of -ENODATA. Just don't bother trying in this case.
v2: explicity check for interconnect-names property
Fixes: 08af4769c7 ("drm/msm: handle for EPROBE_DEFER for of_icc_get")
Fixes: 00bb9243d3 ("drm/msm/gpu: add support for ocmem interconnect path")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Setup an RGB HW pipe as cursor which can be used on
secondary interface.
For SC7180 2 HW pipes are enumerated as cursors
1 - primary interface
2 - secondary interface
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
"The PM core always increments the runtime usage counter
before calling the ->suspend() callback and decrements it
after calling the ->resume() callback"
DPU and DSI are managed as runtime devices. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend was not getting called
and it kept the clocks on which resulted in target not
entering into XO shutdown.
Add changes to force suspend on runtime devices during pm sleep.
Changes in v1:
- Remove unnecessary checks in the function
_dpu_kms_disable_dpu (Rob Clark).
Changes in v2:
- Avoid using suspend_late to reset the usagecount
as suspend_late might not be called during suspend
call failures (Doug).
Changes in v3:
- Use force suspend instead of managing device usage_count
via runtime put and get API's to trigger callbacks (Doug).
Changes in v4:
- Check the return values of pm_runtime_force_suspend and
pm_runtime_force_resume API's and pass appropriately (Doug).
Changes in v5:
- With v4 patch, test cycle has uncovered issues in device resume.
On bubs: cmd tx failures were seen as SW is sending panel off
commands when the dsi resources are turned off.
Upon suspend, DRM driver will issue a NULL composition to the
dpu, followed by turning off all the HW blocks.
v5 changes will serialize the NULL commit and resource unwinding
by handling them under PM prepare and PM complete phases there by
ensuring that clks are on when panel off commands are being
processed.
Changes in v6:
- Use drm_mode_config_helper_suspend/resume() instead of legacy API
drm_atomic_helper_suspend/resume() (Doug).
Trigger runtime callbacks from the suspend/resume call to turn
off the resources.
Changes in v7:
- Add "__maybe_unused" to the functions to avoid compilation
failures. Cleanup unnecessary configs (Doug).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Check for errors instead of silently not using icc if the msm driver
probes before the interconnect driver.
Allow ENODATA for ocmem path, as it is optional and this error
is returned when "gfx-mem" path is provided but not "ocmem".
Because msm_gpu_cleanup assumes msm_gpu_init has been called, the icc path
init needs to be after msm_gpu_init for the error path to work.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
These never get set back to 0 when probing fails, so an attempt to probe
again results in broken behavior. Fix the problem by setting thse to zero
before they are used.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
adreno_gpu_init calls pm_runtime_enable, so adreno_gpu_cleanup needs to
call pm_runtime_disable.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge v5.8-rc6 into drm-next
I've got a silent conflict + two trees based on fixes to merge.
Fixes a silent merge with amdgpu
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only when vblanks are supported ofc.
Some drivers do this already, but most unfortunately missed it. This
opens up bugs after driver load, before the crtc is enabled for the
first time. syzbot spotted this when loading vkms as a secondary
output. Given how many drivers are buggy it's best to solve this once
and for all in shared helper code.
Aside from moving the few existing calls to drm_crtc_vblank_reset into
helpers (i915 doesn't use helpers, so keeps its own) I think the
regression risk is minimal: atomic helpers already rely on drivers
calling drm_crtc_vblank_on/off correctly in their hooks when they
support vblanks. And driver that's failing to handle vblanks after
this is missing those calls already, and vblanks could only work by
accident when enabling a CRTC for the first time right after boot.
Big thanks to Tetsuo for helping track down what's going wrong here.
There's only a few drivers which already had the necessary call and
needed some updating:
- komeda, atmel and tidss also needed to be changed to call
__drm_atomic_helper_crtc_reset() intead of open coding it
- tegra and msm even had it in the same place already, just code
motion, and malidp already uses __drm_atomic_helper_crtc_reset().
- Laurent noticed that rcar-du and omap open-code their crtc reset and
hence would actually be broken by this patch now. So fix them up by
reusing the helpers, which brings the drm_crtc_vblank_reset() back.
Only call left is in i915, which doesn't use drm_mode_config_reset,
but has its own fastboot infrastructure. So that's the only case where
we actually want this in the driver still.
I've also reviewed all other drivers which set up vblank support with
drm_vblank_init. After the previous patch fixing mxsfb all atomic
drivers do call drm_crtc_vblank_on/off as they should, the remaining
drivers are either legacy kms or legacy dri1 drivers, so not affected
by this change to atomic helpers.
v2: Use the drm_dev_has_vblank() helper.
v3: Laurent pointed out that omap and rcar-du used drm_crtc_vblank_off
instead of drm_crtc_vblank_reset. Adjust them too.
v4: Laurent noticed that rcar-du and omap open-code their crtc reset
and hence would actually be broken by this patch now. So fix them up
by reusing the helpers, which brings the drm_crtc_vblank_reset() back.
v5: also mention rcar-du and ompadrm in the proper commit message
above (Laurent).
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://syzkaller.appspot.com/bug?id=0ba17d70d062b2595e1f061231474800f076c7cb
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot+0871b14ca2e2fb64f6e3@syzkaller.appspotmail.com
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Emil Velikov <emil.velikov@collabora.com>
Cc: zhengbin <zhengbin13@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-tegra@vger.kernel.org
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612160056.2082681-1-daniel.vetter@ffwll.ch
A few fixes, mostly fallout from the address space refactor and dpu
color processing.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv0SSXArdYs=mOLqJPJdkvk8CpxaJGecqgbOGazQ2n5og@mail.gmail.com
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
msm_gem_address_space_create() changed to take a start/length instead
of a start/end for the iova space but all of the callers were just
cut and pasted from the old usage. Most of the mistakes have been fixed
up so just catch up the rest.
Fixes: ccac7ce373 ("drm/msm: Refactor address space initialization")
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We don't want it under CONFIG_DRM_MSM_GPU_STATE, we need it all the
time (like the other GPUs do).
Fixes: ccac7ce373 ("drm/msm: Refactor address space initialization")
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Previously the address space went from 16M to ~0u, but with the
refactor one of the 'f's was dropped, limiting us to 256MB.
Additionally, the new interface takes a start and size, not start and
end, so we can't just copy and paste.
Fixes regressions in dEQP-VK.memory.allocation.random.*
Fixes: ccac7ce373 ("drm/msm: Refactor address space initialization")
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Ingo suggested that since the new sched_set_*() functions are
implemented using the 'nocheck' variants, they really shouldn't ever
fail, so remove the return value.
Cc: axboe@kernel.dk
Cc: daniel.lezcano@linaro.org
Cc: sudeep.holla@arm.com
Cc: airlied@redhat.com
Cc: broonie@kernel.org
Cc: paulmck@kernel.org
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Use sched_set_fifo(); Effectively changes prio from 16 to 50.
Cc: airlied@redhat.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
This week I started seeing GPU crashes on my DragonBoard 845c
which I narrowed down to being caused by commit ccac7ce373
("drm/msm: Refactor address space initialization").
Looking through the patch, Jordan and I couldn't find anything
obviously wrong, so I ended up breaking that change up into a
number of smaller logical steps so I could figure out which part
was causing the trouble.
Ends up, visually counting 'f's is hard, esp across a number
of lines:
0xfffffff != 0xffffffff
This patch corrects the end value we pass in to
msm_gem_address_space_create() in
adreno_iommu_create_address_space() so that it matches the value
used before the problematic patch landed.
With this change, I no longer see the GPU crashes that were
affecting me.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: freedreno@lists.freedesktop.org
Fixes: ccac7ce373 ("drm/msm: Refactor address space initialization")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the current implementation, mutex initialization
for encoder mutex locks are done during encoder
setup. This can lead to scenarios where the lock
is used before it is initialized. Move mutex_init
to dpu_encoder_init to avoid this.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix to return negative error code -ENOMEM with the use of
ERR_PTR from dpu_encoder_init.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Chen Tao <chentao107@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
In function msm_submitqueue_create, the queue is a local
variable, in return -EINVAL branch, queue didn`t add to ctx`s
list yet, and also didn`t kfree, this maybe bring in potential
memleak.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
[trivial commit msg fixup]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Request for color processing blocks only if they are
available in the display hw catalog and they are
sufficient in number for the selection.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Fixes: e47616df00 ("drm/msm/dpu: add support for color processing
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
* new gpu support: a405, a640, a650
* dpu: color processing support
* mdp5: support for msm8x36 (the thing with a405)
* some prep work for per-context pagetables (ie the part that
does not depend on in-flight iommu patches)
* last but not least, UABI update for submit ioctl to support
syncobj (from Bas)
-----BEGIN PGP SIGNATURE-----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=hIK6
-----END PGP SIGNATURE-----
Merge tag 'drm-next-msm-5.8-2020-06-08' of git://anongit.freedesktop.org/drm/drm
Pull drm msm updates from Dave Airlie:
"This tree has been in next for a couple of weeks, but Rob missed an
arm32 build issue, so I was awaiting the tree with a patch reverted.
- new gpu support: a405, a640, a650
- dpu: color processing support
- mdp5: support for msm8x36 (the thing with a405)
- some prep work for per-context pagetables (ie the part that does
not depend on in-flight iommu patches)
- last but not least, UABI update for submit ioctl to support syncobj
(from Bas)"
* tag 'drm-next-msm-5.8-2020-06-08' of git://anongit.freedesktop.org/drm/drm: (30 commits)
Revert "drm/msm/dpu: add support for clk and bw scaling for display"
drm/msm/a6xx: skip HFI set freq if GMU is powered down
drm/msm: Update the MMU helper function APIs
drm/msm: Refactor address space initialization
drm/msm: Attach the IOMMU device during initialization
drm/msm/dpu: dpu_setup_dspp_pcc() can be static
drm/msm/a6xx: a6xx_hfi_send_start() can be static
drm/msm/a4xx: add a405_registers for a405 device
drm/msm/a4xx: add adreno a405 support
drm/msm/a6xx: update a6xx_hw_init for A640 and A650
drm/msm/a6xx: enable GMU log
drm/msm/a6xx: update pdc/rscc GMU registers for A640/A650
drm/msm/a6xx: A640/A650 GMU firmware path
drm/msm/a6xx: HFI v2 for A640 and A650
drm/msm/a6xx: add A640/A650 to gpulist
drm/msm/a6xx: use msm_gem for GMU memory objects
drm/msm: add internal MSM_BO_MAP_PRIV flag
drm/msm: add msm_gem_get_and_pin_iova_range
drm/msm: Check for powered down HW in the devfreq callbacks
drm/msm/dpu: update bandwidth threshold check
...
I honestly don't exactly understand what's going on here, but the
current code is wrong for sure: It calls dma_buf_vunmap without ever
calling dma_buf_vmap.
What I'm not sure about is whether the WARN_ON is correct:
- msm imports dma-buf using drm_prime_sg_to_page_addr_arrays. Which is
a pretty neat layering violation of how you shouldn't peek behind
the curtain of the dma-buf exporter, but par for course. Note that
all the nice new helpers don't (and we should probably have a bit a
warning about this in the kerneldoc).
- but then in the get_vaddr() in msm_gem.c, we seems to happily wrap a
vmap() around any object with ->pages set (so including imported
dma-buf).
- I'm not seeing any guarantees that userspace can't use an imported
dma-buf for e.g. MSM_SUBMIT_CMD_BUF in a5xx_submit_in_rb, so no
guarantees that an imported dma-buf won't end up with a ->vaddr set.
But even if that WARN_ON is wrong, cleaning up a vmap() done by msm by
calling dma_buf_vunmap is the wrong thing to do.
v2: Rob said in review that we do indeed have a gap in get_vaddr() that
needs to be plugged. But the users I've found aren't legit users on
imported dma-buf, so we can just reject that.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200514201117.465146-1-daniel.vetter@ffwll.ch
This is causing multiple armv7 missing do_div() errors, so lets drop it
for now.
This reverts commit 04d9044f6c.
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Also skip the newly added HFI set freq path if the GMU is powered down,
which was missing because of patches crossing paths.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of using a bare unsigned type for the length value for map/unmap
functions pass in a size_t to more correctly match up with the underlying
APIs.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Refactor how address space initialization works. Instead of having the
address space function create the MMU object (and thus require separate but
equal functions for gpummu and iommu) use a single function and pass the
MMU struct in. Make the generic code cleaner by using target specific
functions to create the address space so a2xx can do its own thing in its
own space. For all the other targets use a generic helper to initialize
IOMMU but leave the door open for newer targets to use customization
if they need it.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[squash in rebase fixups]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Everywhere an IOMMU object is created by msm_gpu_create_address_space
the IOMMU device is attached immediately after. Instead of carrying around
the infrastructure to do the attach from the device specific code do it
directly in the msm_iommu_init() function. This gets it out of the way for
more aggressive cleanups that follow.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[squash in rebase fixups and fix for unused fxn]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes: 4259ff7ae5 ("drm/msm/dpu: add support for pcc color block in dpu driver")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes: 8167e6fa76 ("drm/msm/a6xx: HFI v2 for A640 and A650")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Spelling out _unlocked for each and every driver is a annoying.
Especially if we consider how many drivers, do not know (or need to)
about the horror stories involving struct_mutex.
Just drop the suffix. It makes the API cleaner.
Done via the following script:
__from=drm_gem_object_put_unlocked
__to=drm_gem_object_put
for __file in $(git grep --name-only $__from); do
sed -i "s/$__from/$__to/g" $__file;
done
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-25-emil.l.velikov@gmail.com
Vast majority of DRM (core and drivers) are struct_mutex free.
As such we have only a handful of cases where the locked helper should
be used. Make that stand out a little bit better.
Done via the following script:
__from=drm_gem_object_put
__to=drm_gem_object_put_locked
for __file in $(git grep --name-only --word-regexp $__from); do
sed -i "s/\<$__from\>/$__to/g" $__file;
done
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-12-emil.l.velikov@gmail.com
A405 device has a different set of registers than a4xx_registers. It
has no VMIDMT or XPU registers, and VBIF registers are different. Let's
add a405_registers for a405 device.
As adreno_is_a405() works only after adreno_gpu_init() gets called, the
assignments get moved down after adreno_gpu_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
It adds support for adreno a405 found on MSM8939. The adreno_is_a430()
check in adreno_submit() needs an extension to cover a405. The
downstream driver suggests it should cover the whole a4xx generation.
That's why it gets changed to adreno_is_a4xx(), while a420 is not
tested though.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Adreno 640 and 650 GPUs need some registers set differently.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This is required for a650 to work.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Update the gmu_pdc registers for A640 and A650.
Some of the RSCC registers on A650 are in a separate region.
Note this also changes the address of these registers:
RSCC_TCS1_DRV0_STATUS
RSCC_TCS2_DRV0_STATUS
RSCC_TCS3_DRV0_STATUS
Based on the values in msm-4.14 and msm-4.19 kernels.
v3: replaced adreno_is_a650 around ->rscc with checks for "rscc" resource
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Newer GPUs have different GMU firmware path.
v3: updated a6xx_gmu_fw_load based on feedback, including gmu_write_bulk,
and removed extra whitespace change
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add HFI v2 code paths required by Adreno 640 and 650 GPUs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add Adreno 640 and 650 GPU info to the gpulist.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This gives more fine-grained control over how memory is allocated over the
DMA api. In particular, it allows using an address range or pinning to
a fixed address.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This flag sets IOMMU_PRIV, which is required for some a6xx GMU objects.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This function allows pinning iova to a specific page range (for a6xx GMU).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Writing to the devfreq sysfs nodes while the GPU is powered down can
result in a system crash (on a5xx) or a nasty GMU error (on a6xx):
$ /sys/class/devfreq/5000000.gpu# echo 500000000 > min_freq
[ 104.841625] platform 506a000.gmu: [drm:a6xx_gmu_set_oob]
*ERROR* Timeout waiting for GMU OOB set GPU_DCVS: 0x0
Despite the fact that we carefully try to suspend the devfreq device when
the hardware is powered down there are lots of holes in the governors that
don't check for the suspend state and blindly call into the devfreq
callbacks that end up triggering hardware reads in the GPU driver.
Call pm_runtime_get_if_in_use() in the gpu_busy() and gpu_set_freq()
callbacks to skip the hardware access if it isn't active.
v3: Only check pm_runtime_get_if_in_use() for == 0 per Eric Anholt
v2: Use pm_runtime_get_if_in_use() per Eric Anholt
Cc: stable@vger.kernel.org
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Maximum allowed bandwidth has no dependency on the type
of panel used. Hence, cleanup the code to use max_bw_high
as the threshold value for bandwidth checks.
Update the maximum allowed bandwidth as 6.8Gbps for
SC7180 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to scale src clk and bandwidth as
per composition requirements.
Interconnect registration for bw has been moved to mdp
device node from mdss to facilitate the scaling.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support for color correction sub block
for SC7180 device.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds support to configure dspp blocks in
the dpu driver.
Macro description of the changes coming in this patch.
1) Add dspp definitions in the hw catalog.
2) Add capability to reserve dspp blocks in the display data path.
3) Attach the reserved block to the encoder.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Fritz Koenig <frkoenig@google.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When allocation for mdp5_kms fails, calling mdp5_destroy() leads to undefined
behaviour, likely a nullptr exception or use-after-free troubles.
Signed-off-by: Roy Spliet <nouveau@spliet.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
rd_full should be defined outside the CONFIG_DEBUG_FS region, in order
to be able to link the msm driver even when CONFIG_DEBUG_FS is disabled.
Fixes: e515af8d4a ("drm/msm: devcoredump should dump MSM_SUBMIT_BO_DUMP buffers")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This
1) Enables core DRM syncobj support.
2) Adds options to the submission ioctl to wait/signal syncobjs.
Just like the wait fence fd, this does inline waits. Using the
scheduler would be nice but I believe it is out of scope for
this work.
Support for timeline syncobjs is implemented and the interface
is ready for it, but I'm not enabling it yet until there is
some code for turnip to use it.
The reset is mostly in there because in the presence of waiting
and signalling the same semaphores, resetting them after
signalling can become very annoying.
v2:
- Fixed style issues
- Removed a cleanup issue in a failure case
- Moved to a copy_from_user per syncobj
v3:
- Fixed a missing declaration introduced in v2
- Reworked to use ERR_PTR/PTR_ERR
- Simplified failure gotos.
Used by: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/2769
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Using the following command will get compile warnings:
make W=1 drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.o ARCH=arm64
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘_dpu_crtc_program_lm_output_roi’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:91:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_atomic_begin’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:428:35: warning: variable
‘smmu_state’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc_smmu_state_data *smmu_state;
^~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_atomic_flush’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:489:25: warning: variable
‘event_thread’ set but not used [-Wunused-but-set-variable]
struct msm_drm_thread *event_thread;
^~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_destroy_state’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:565:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_duplicate_state’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:664:19: warning: variable
‘dpu_crtc’ set but not used [-Wunused-but-set-variable]
struct dpu_crtc *dpu_crtc;
^~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function
‘dpu_crtc_disable’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:693:26: warning: variable
‘priv’ set but not used [-Wunused-but-set-variable]
struct msm_drm_private *priv;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:691:27: warning: variable
‘mode’ set but not used [-Wunused-but-set-variable]
struct drm_display_mode *mode;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function ‘dpu_crtc_enable’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:766:26: warning: variable
‘priv’ set but not used [-Wunused-but-set-variable]
struct msm_drm_private *priv;
^~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c: In function ‘dpu_crtc_init’:
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:1292:18: warning: variable
‘kms’ set but not used [-Wunused-but-set-variable]
struct dpu_kms *kms = NULL;
^~~
drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:663: warning: Excess function
parameter 'Returns' description in 'dpu_crtc_duplicate_state'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
'in' is duplicated in the error message. Axe one of them.
While at it, slighly improve indentation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This change adds MDP5 configuration for MSM8x36-based SoCs,
like MSM8936, 8939 and their APQ variants.
The configuration is based on MSM8916's, but adds some notable
features, like ad and pp blocks, along with some register
changes.
changes since v1:
- add an ad block
- add a second mixer @ 0x47000
- adjust .max_width
- write a more descriptive commit message
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Including:
- ARM-SMMU support for the TLB range invalidation command in
SMMUv3.2.
- ARM-SMMU introduction of command batching helpers to batch up
CD and ATC invalidation.
- ARM-SMMU support for PCI PASID, along with necessary PCI
symbol exports.
- Introduce a generic (actually rename an existing) IOMMU
related pointer in struct device and reduce the IOMMU related
pointers.
- Some fixes for the OMAP IOMMU driver to make it build on 64bit
architectures.
- Various smaller fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=nhuS
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM-SMMU support for the TLB range invalidation command in SMMUv3.2
- ARM-SMMU introduction of command batching helpers to batch up CD and
ATC invalidation
- ARM-SMMU support for PCI PASID, along with necessary PCI symbol
exports
- Introduce a generic (actually rename an existing) IOMMU related
pointer in struct device and reduce the IOMMU related pointers
- Some fixes for the OMAP IOMMU driver to make it build on 64bit
architectures
- Various smaller fixes and improvements
* tag 'iommu-updates-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu: Move fwspec->iommu_priv to struct dev_iommu
iommu/virtio: Use accessor functions for iommu private data
iommu/qcom: Use accessor functions for iommu private data
iommu/mediatek: Use accessor functions for iommu private data
iommu/renesas: Use accessor functions for iommu private data
iommu/arm-smmu: Use accessor functions for iommu private data
iommu/arm-smmu: Refactor master_cfg/fwspec usage
iommu/arm-smmu-v3: Use accessor functions for iommu private data
iommu: Introduce accessors for iommu private data
iommu/arm-smmu: Fix uninitilized variable warning
iommu: Move iommu_fwspec to struct dev_iommu
iommu: Rename struct iommu_param to dev_iommu
iommu/tegra-gart: Remove direct access of dev->iommu_fwspec
drm/msm/mdp5: Remove direct access of dev->iommu_fwspec
ACPI/IORT: Remove direct access of dev->iommu_fwspec
iommu: Define dev_iommu_fwspec_get() for !CONFIG_IOMMU_API
iommu/virtio: Reject IOMMU page granule larger than PAGE_SIZE
iommu/virtio: Fix freeing of incomplete domains
iommu/virtio: Fix sparse warning
iommu/vt-d: Add build dependency on IOASID
...
A bit smaller this time around.. there are still a couple uabi
additions for vulkan waiting in the wings, but I punted on them this
cycle due to running low on time. (They should be easy enough to
rebase, and if it is a problem for anyone I can push a next+uabi
branch so that tu work can proceed.)
The bigger change is refactoring dpu resource manager and moving dpu
to use atomic global state. Other than that, it is mostly cleanups
and fixes.
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGuf1R4Xz-t9Z7_cwx9jD=b4wUvvwfqA5cHR8fCSXSd5XQ@mail.gmail.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GMU has very few memory allocations and uses a flat memory space so
there is no good reason to go out of our way to bypass the DMA APIs which
were basically designed for this exact scenario.
v7: Check return value of dma_set_mask_and_coherent
v4: Use dma_alloc_wc()
v3: Set the dma mask correctly and use dma_addr_t for the iova type
v2: Pass force_dma false to of_dma_configure to require that the DMA
region be set up and return error from of_dma_configure to fail probe.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Also log buffers with the DUMP flag set, to ensure we capture all useful
cmdstream in crashdump state with modern mesa.
Otherwise we miss out on the contents of "state object" cmdstream
buffers.
v2: add missing 'inline'
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
If the opp table specifies opp-supported-hw as a property but the driver
has not set a supported hardware value the OPP subsystem will reject
all the table entries.
Set a "default" value that will match the default table entries but not
conflict with any possible real bin values. Also fix a small memory leak
and free the buffer allocated by nvmem_cell_read().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes coccicheck warning:
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:27:51-52: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:109:51-52: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:167:12-13: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:167:22-23: WARNING comparing pointer to 0
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes coccicheck warning:
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c:242:48-49: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c:562:25-26: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_vid.c:562:48-49: WARNING comparing pointer to 0
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes coccicheck warning:
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c:414:52-53: WARNING comparing pointer to 0
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_cmd.c:443:56-57: WARNING comparing pointer to 0
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
