Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
(cherry picked from commit 3f61ef9777)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Alderlake-P was getting 'max time under evasion' messages when PSR2
is enabled, this is due PIPE_SCANLINE/PIPEDSL returning 0 over a
period of time longer than VBLANK_EVASION_TIME_US.
For PSR1 we had the same issue so intel_psr_wait_for_idle() was
implemented to wait for PSR1 to get into idle state but nothing was
done for PSR2.
For PSR2 we can't only wait for idle state as PSR2 tends to keep
into sleep state(ready to send selective updates).
Waiting for any state below deep sleep proved to be effective in
avoiding the evasion messages and also not wasted a lot of time.
v2:
- dropping the additional wait_for loops, only the _wait_for_atomic()
is necessary
- waiting for states below EDP_PSR2_STATUS_STATE_DEEP_SLEEP
v3:
- dropping intel_wait_for_condition_atomic() function
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005231851.67698-1-jose.souza@intel.com
The intermediate value 1000000 * 10 * 9671 overflows 32 bits, so force
promotion to a bigger type.
From the logs:
[drm:intel_dp_compute_config [i915]] DP link rate required 3657063 available -580783288
v2: Use mul_u32_u32() (Ville)
Fixes: 48efd014f0 ("drm/i915/dp: add max data rate calculation for UHBR rates")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026093407.11381-1-jani.nikula@intel.com
Reading out the DP encoders' DPCD during booting or resume is only
required for enabled encoders: such encoders may be modesetted during
the initial commit and the link training this involves depends on an
initialized DPCD. For DDI encoders reading out the DPCD is skipped, do
the same on pre-DDI platforms.
Atm, the first DPCD readout without a sink connected - which is a likely
scneario if the encoder is disabled - leaves intel_dp->num_common_rates
at 0, which resulted in
intel_dp_sync_state()->intel_dp_max_common_rate()
in a
intel_dp->common_rates[-1]
access. This by definition results in an undefined behaviour, though to
my best knowledge in all HW/compiler configurations it actually results
in accessing the array item type value preceding the array. In this
case the preceding value happens to be intel_dp->num_common_rates,
which is 0, so this issue - by luck - didn't cause a user visible
problem.
Nevertheless it's still an undefined behaviour and in CONFIG_UBSAN
builds leads to a kernel BUG() (which revealed this problem for us),
hence CC:stable.
A related problem in case the encoder is enabled but the sink is not
connected or the DPCD readout fails is fixed by the next patch.
v2: Amend the commit message describing the root cause of the
CONFIG_UBSAN BUG().
Fixes: a532cde31d ("drm/i915/tc: Fix TypeC port init/resume time sanitization")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
Reported-and-tested-by: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-2-imre.deak@intel.com
(cherry picked from commit 4ec5ffc341)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
8b/10b encoding format requires to reserve the first slot for
recording metadata. Real data transmission starts from the second slot,
with a total of available 63 slots available.
In 128b/132b encoding format, metadata is transmitted separately
in LLCP packet before MTP. Real data transmission starts from
the first slot, with a total of 64 slots available.
v2:
* Move total/start slots to mst_state, and copy it to mst_mgr in
atomic_check
v3:
* Only keep the slot info on the mst_state
* add a start_slot parameter to the payload function, to facilitate non
atomic drivers (this is a temporary workaround and should be removed when
we are moving out the non atomic driver helpers)
v4:
*fixed typo and formatting
v5: (no functional changes)
* Fixed formatting in drm_dp_mst_update_slots()
* Reference mst_state instead of mst_state->mgr for debugging info
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
[v5 nitpicks]
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-3-lyude@redhat.com
If we want to return from for_each_intel_connector_iter(), one
way is calling drm_connector_list_iter_end() before returning
to avoid memleak. The other way is just breaking from the bracket
and then returning after the outside drm_connector_list_iter_end().
Obviously, the second way makes code smaller and more clear.
Apply it to the function intel_dp_mst_atomic_master_trans_check().
Signed-off-by: He Ying <heying24@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022022243.138860-1-heying24@huawei.com
Reorganize the HDMI 4:2:0 handling a bit by introducing
intel_hdmi_output_format(). We already have the DP counterpart
and I want to unify the 4:2:0 handling across both a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015133921.4609-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename intel_hdmi_port_clock() into intel_hdmi_tmds_clock(), and
move the 4:2:0 TMDS clock halving into intel_hdmi_tmds_clock() so
the callers don't have to worry about such details.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015133921.4609-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Introduce a small helper which given the crtc state tells us
whether we're output YCbCr 4:2:0 or not. For native HDMI this
is rather simple as we just look at the output_format. But I
think the helper is beneficial since with DP HDMI DFPs we're
going to need a more complex variant, and I want to unify the
DP and HDMI sides of that as much as possible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015133921.4609-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
intel_hdmi_bpc_possible() is used by the DP code as well where
the native HDMI source limits do not apply. So let's split this
into a pair of functions: one for the source vs. one for the sink.
This is basically reverting some of commit 41828125ac ("drm/i915:
Move platform checks into intel_hdmi_bpc_possible()") slightly,
but in a nicer form. I guess I forgot at the time that the DP side
uses this too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015133921.4609-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Instead of open-coding the checks add functions for this, simplifying
the handling of CCS modifiers on future platforms.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-12-imre.deak@intel.com
Move the function to intel_fb.c and rename it adding the intel_fb_
prefix following the naming of exported functions.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-11-imre.deak@intel.com
Future platforms change the location of CCS AUX planes in CCS
framebuffers, so add intel_fb_is_ccs_aux_plane() to query for these
planes independently of the platform. This function can be used
everywhere instead of is_ccs_plane() (or is_ccs_plane() && !cc_plane()),
since all the callers are only interested in CCS AUX planes (and not CCS
color-clear planes).
Add the corresponding intel_fb_is_gen12_ccs_aux_plane(), which can be
used everywhere instead of is_gen12_ccs_plane(), based on the above
explanation.
This change also unexports the is_gen12_ccs_modifier(),
is_gen12_ccs_plane(), is_gen12_ccs_cc_plane() functions as they are only
used in intel_fb.c
v1-v2: Unchanged
v3: (Ville)
- Use ccs_aux instead of the ccs_ctrl term everywhere.
- Use color_plane instead of plane term for FB plane indicies.
v4: Fix version range check. (Jani)
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-10-imre.deak@intel.com
CCS CC planes are quite different from CCS AUX planes, even though we
regard the CC planes as a linear buffer having a 64 byte stride. Thus
it's clearer to check for either CCS plane types explicitly when we need
to handle them; add the required CCS CC planes check here, while the
next patch will change all is_ccs_plane()/is_gen12_ccs_plane() checks to
consider only the CCS AUX planes.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-9-imre.deak@intel.com
On future platforms the index of the color-clear plane will change from
the one used by the GEN12 RC CCS CC modifier, so add a way to retrieve
the index independently of the platform/modifier.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-8-imre.deak@intel.com
Move intel_format_info_is_yuv_semiplanar() to intel_fb.c . The number of
planes for YUV semiplanar formats using CCS modifiers will change on
future platforms. We can use the modifier descriptors to simplify
getting the plane numbers for all modifiers, prepare for that here.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-7-imre.deak@intel.com
Checking the modifiers that support interlacing makes the condition
simpler and avoids us having to add new modifiers to the list (presuming
all/most of the new modifiers won't support interlacing).
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-5-imre.deak@intel.com
Add a tiling atttribute to the modifier descriptor, which let's us
get the tiling without listing the modifiers twice.
v1-v2: Unchanged.
v3:
- Initialize .tiling to I915_TILING_NONE explicitly (Ville)
- Move from previous patch lookup_modifier() to here, where it's first
used.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-4-imre.deak@intel.com
Move the function retrieving the format override information for a given
format/modifier to intel_fb.c. We can store a pointer to the format list
in each modifier's descriptor instead of the corresponding switch/case
logic, avoiding the listing of the modifiers twice.
v1: Unchanged.
v2: Handle invalid modifiers in intel_fb_get_format_info() passed from
userspace. (CI/igt_kms_addfb_basic/addfb25-bad-modifier)
v3: Move lookup_modifier() to the next patch, where it's first used.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-3-imre.deak@intel.com
Add a table describing all the framebuffer modifiers used by i915 at one
place. This has the benefit of deduplicating the listing of supported
modifiers for each platform and checking the support of these modifiers
on a given plane. This also simplifies in a similar way getting some
attribute for a modifier, for instance checking if the modifier is a
CCS modifier type.
While at it drop the cursor plane filtering from skl_plane_has_rc_ccs(),
as the cursor plane is registered with DRM core elsewhere.
v1: Unchanged.
v2:
- Keep the plane caps calculation in the plane code and pass an enum
with these caps to intel_fb_get_modifiers(). (Ville)
- Get the modifiers calling intel_fb_get_modifiers() in i9xx_plane.c as
well.
v3:
- s/.id/.modifier/ (Ville)
- Keep modifier_desc vs. plane_cap filter conditions consistent. (Ville)
- Drop redundant cursor plane check from skl_plane_has_rc_ccs(). (Ville)
- Use from, until display version fields in modifier_desc instead of a mask. (Jani)
- Unexport struct intel_modifier_desc, separate its decl and init. (Jani)
- Remove enum pipe, plane_id forward decls from intel_fb.h, which are
not needed after v2.
v4:
- Reuse IS_DISPLAY_VER() instead of open-coding it. (Jani)
- Preserve the current modifier order exposed to user space. (Ville)
v5: Use }, { on one line to seperate the descriptor array elements. (Jani)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> (v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-2-imre.deak@intel.com
This reverts commit 05734ca2a8.
It's not graceful, instead it leads to boot time warning splats in the
case it is supposed to handle gracefully. Apparently the BIOS/GOP
enabling the port we end up skipping leads to state readout
problems. Back to the drawing board.
References: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_21255/bat-adlp-4/boot0.txt
Fixes: 05734ca2a8 ("drm/i915/bios: gracefully disable dual eDP for now")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019114334.24643-1-jani.nikula@intel.com
Right now the only user of psr_pause/resume is intel_cdclk but
additional users will be added in the future and we may need
do reference counting for PSR pause and resume, for now only adding a
warn_on so this cases do not go unnoticed.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jouni Hogander <jouni.hogander@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020003558.222198-2-jose.souza@intel.com
This power domain to disable DC states will be used in places outside
of DPLL, so making the name more generic.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Caz Yokoyama <caz.yokoyama@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020003558.222198-1-jose.souza@intel.com
Add an assert that lookups from the intel_dp->common_rates[] array
are always valid.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-7-imre.deak@intel.com
If the DPCD sink rate values read from the sink are invalid, the
driver will sanitize this in intel_dp_set_common_rates(), by setting a
default 162000 link rate in common rates and printing a WARN().
WARN()s should only be triggered by bugs in the code and not by external
factors like the above (an invalid DPCD injected maliciously or read from a
buggy monitor). So fixup the invalid DPCD sink rate values already and print
an error in this case (since it's still a user visible problem).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-6-imre.deak@intel.com
Print an error if the DPCD sink max lane count is invalid and fix it up.
While at it also add an assert that the link max lane count (derived
from intel_dp_max_common_lane_count(), potentially reduced by the LT
fallback logic) value is also valid.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-5-imre.deak@intel.com
Atm until the DPCD for a connector is read the max link rate and lane
count params are invalid. If the connector is modeset, in
intel_dp_compute_config(), intel_dp_common_len_rate_limit(max_link_rate)
will return 0, leading to a intel_dp->common_rates[-1] access.
Fix the above by making sure the max link params are always valid.
The above access leads to an undefined behaviour by definition, though
not causing a user visible problem to my best knowledge, see the previous
patch why. Nevertheless it is an undefined behaviour and it triggers a
BUG() in CONFIG_UBSAN builds, hence CC:stable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-4-imre.deak@intel.com
Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
Reading out the DP encoders' DPCD during booting or resume is only
required for enabled encoders: such encoders may be modesetted during
the initial commit and the link training this involves depends on an
initialized DPCD. For DDI encoders reading out the DPCD is skipped, do
the same on pre-DDI platforms.
Atm, the first DPCD readout without a sink connected - which is a likely
scneario if the encoder is disabled - leaves intel_dp->num_common_rates
at 0, which resulted in
intel_dp_sync_state()->intel_dp_max_common_rate()
in a
intel_dp->common_rates[-1]
access. This by definition results in an undefined behaviour, though to
my best knowledge in all HW/compiler configurations it actually results
in accessing the array item type value preceding the array. In this
case the preceding value happens to be intel_dp->num_common_rates,
which is 0, so this issue - by luck - didn't cause a user visible
problem.
Nevertheless it's still an undefined behaviour and in CONFIG_UBSAN
builds leads to a kernel BUG() (which revealed this problem for us),
hence CC:stable.
A related problem in case the encoder is enabled but the sink is not
connected or the DPCD readout fails is fixed by the next patch.
v2: Amend the commit message describing the root cause of the
CONFIG_UBSAN BUG().
Fixes: a532cde31d ("drm/i915/tc: Fix TypeC port init/resume time sanitization")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
Reported-and-tested-by: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-2-imre.deak@intel.com
Use the new link training delay helpers, fixing the delays for
128b/132b.
For existing 8b/10b functionality, this will cause additional 1-byte
DPCD reads for LTTPR delays instead of using the cached values. It's
just too complicated to combine generic helpers with local caching in a
sensible way.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014150059.28957-3-jani.nikula@intel.com
Let's add lpt_pch_disable() as the counterpart to
lpt_pch_enable().
Note that unlike the ilk+ code the fdi_link_train()
and fdi_disable() calls are still left directly in
intel_crt.c. If we wanted to move those we'd need to
add lpt_pch_pre_enable(). But the two fdi direct fdi
calls are pretry symmetric so it doesn't seem too bad
to just keep them as is.
v2: Make lpt_disable_pch_transcoder() static (lkp@intel.com)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-10-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reanme intel_ddi_fdi_post_disable() to hsw_fdi_disable() and
relocate it next to all the other code dealing with FDI_RX.
intel_ddi.c has now been cleansed of FDI_RX.
In order to avoid exposing intel_disable_ddi_buf() outside
intel_ddi.c we can just open code the DDI_BUF_CTL write. The
enable side already has all that stuff open coded so
this actually is more symmetric. But we do need to remeber
to bring the intel_wait_ddi_buf_idle() call over from
inside intel_disable_ddi_buf().
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-9-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Hoover the remaining open coded PCH modeset sequence bits
out from ilk_crtc_disable(). Somewhat annoyingly the
enable vs. disable is a bit asymmetric so we need two
functions for the disable case.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-8-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Move the lpt_get_iclkip() call from hsw_crt_get_config()
since that's where we have the lpt_program_iclkip() call
as well.
Tehcnically this isn't perhaps quite right since iCLKIP
is providing the CRT dotclock. So one can argue all of
it should be directly in intel_crt.c. But since the CRT
port is the only one on the PCH sticking it all into the
PCH code seems OK.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-7-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Pull the ilk+ PCH state readout into its own function and relocate
to the appropriate file.
The clock readout parts are perhaps a bit iffy since we depend
on the gmch DPLL readout code. But we can think about the clock
readout big picture later.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-6-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Nuke the hsw_get_ddi_port_state() eyesore by putting the
readout code into intel_pch_display.c, and calling it directly
from hsw_crt_get_config().
Note that the nuked TRANS_DDI_FUNC_CTL readout from
hsw_get_ddi_port_state() is now etirely redundant since we
get called from the encoder->get_config() so we already know
we're dealing with the correct DDI port. Previously the
code was called from a place where that wasn't known so
it had to checked manually.
v2: Clarify the TRANS_DDI_FUNC_CTL change (Dave)
Nuke the now unused *TRANS_DDI_FUNC_CTL_VAL_TO_PORT() (Dave)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018153525.21597-1-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Use the clean "atomic_state+crtc" approach of passing
arguments to the top level PCH modeset code.
And while at it we can also just pass the whole crtc to
ilk_disable_pch_transcoder().
v2: Elimiate double space between function args (Dave)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-4-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Start moving the code for PCH modeset sequence/etc. to
its own file.
Still not sure about the file name though...
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-3-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Move the PCH refclk stuff (including all the LPT/WPT
iCLKIP/CLKOUT_DP things) to its own file.
We also suck in the mPHY programming from intel_fdi.c
since we're the only caller.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-2-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
intel_load_plane_csc_black() is specific to icl+ so deserves
a name reflecting that fact. Also rename the variables to
standard form so I won't get confused reading the code.
v2: icl+ not glk+
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-5-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com>
We are inside the vblank evade critical section here, racing
against the raster beam. There is no time to print debug
messages.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-4-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com>
There's lots of expensive stuff inserted between the PLANE_CTL
and PLANE_SURF writes even though the comment before the PLANE_CTL
write says not to put stuff there. Move it all to a more apporiate
place.
There's also a weird PLANE_COLOR_CTL RMW in there. I guess because
force_black was computed way too late originally, but that is now
sorted.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
No real reason to have this pxp state computation in
intel_atomic_check_planes(). Just stuff it into skl_plane_check().
There was also some funny state copying being done from the
old plane state to the new plane state when the plane is anyway
disabled.
The one thing we presumably must remember to do is copy
over the decrypt state when assigning a Y plane for planar
YCbCr scanout, so that the Y plane's PLANE_SURF will get the
appropriate bit set. The force_black thing should not matter
as I'm pretty sure all that stuff is ignored for the Y plane.
I suppose this was the reason for the odd placement for the
state computation, but I see no reason to deviate from the
standard way of doing these things. This also guarantees
that we don't calculate things differently between the
linked UV and Y plane.
v2: Only do stuff for icl+ since 'force_black' depends
on the plane CSC which is an icl+ feature
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-2-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com> #v1
We don't have hpd support on i8xx/i915 which means hotplug_funcs==NULL.
Let's not oops when loading the driver on one those machines.
v2: Drop the redundant function pointer check (Jani)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: cd030c7c11 ("drm/i915: constify hotplug function vtable.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014090941.12159-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DKL_TX_LOADGEN_SHARING_PMD_DISABLE doesn't even seem to exist,
also the spec says to skip all loadgen stuff.
The code was dead anyway since it wasn't actually writing the value
anywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The snb+ pcode mailbox code is not sideband, so split it out to a
separate file. As can be seen from the #include changes, very few places
use both sideband and pcode.
Code movement only.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/185deb18eb739e5ae019e27834b9997dcc1347bc.1634207064.git.jani.nikula@intel.com
For the time being, neither the power sequencer nor the backlight code
properly support two eDP panels simultaneously. While the software
states will be independent, the same sets of registers will be used for
both eDP panels, clobbering the hardware state and leading to errors.
Gracefully disable dual eDP until proper support has been added.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005175636.24669-1-jani.nikula@intel.com
The VLV/CHV sideband code is pretty distinct from the rest of the
sideband code. Split it out to new vlv_sideband.[ch].
Pure code movement with relevant #include changes, and a tiny checkpatch
fix on top.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/755ebbbaf01fc6d306b763b6ef60f45e671ba290.1634119597.git.jani.nikula@intel.com
As per the comment on top of acpi_evaluate_dsm():
| * Evaluate device's _DSM method with specified GUID, revision id and
| * function number. Caller needs to free the returned object.
We should free the returned object of acpi_evaluate_dsm() to avoid memory
leakage. Otherwise the kmemleak splat will be triggered at boot time (if we
compile kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE=y).
Fixes: 8e55f99c51 ("drm/i915: Invoke another _DSM to enable MUX on HP Workstation laptops")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906033541.862-1-yuzenghui@huawei.com
(cherry picked from commit 149ac2e7ae)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Need to resync drm-intel-next with TTM and PXP stuff from
drm-intel-gt-next that is now in drm/drm-next.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The 128b/132b channel coding link training uses more straightforward TX
FFE preset values. Reuse voltage tries and max vswing for retry logic.
The delays for 128b/132b are still all wrong, but this is regardless a
step forward.
v2: Fix UHBR rate checks, use intel_dp_is_uhbr() helper
v3:
- Rebase
- Modify intel_dp_adjust_request_changed() and
intel_dp_link_max_vswing_reached() to take 128b/132b into
account. (Ville)
v4:
- Train request printing for TX FFE (Ville)
- Log 8b/10b vs. 128b/132b (Ville)
- Add helper for per-lane max vswing / tx ffe (Ville)
- Name functions with tx_ffe/vswing instead of 128b132b/8b10b
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011182144.22074-2-jani.nikula@intel.com
Add per-lane abstraction for max vswing reached to make follow-up
cleaner, as this one reverses the conditions.
v2: both conditions need to be true, reverse (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011182144.22074-1-jani.nikula@intel.com
UAPI Changes:
- Add uAPI for using PXP protected objects
Mesa changes: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/8064
- Add PCI IDs and LMEM discovery/placement uAPI for DG1
Mesa changes: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/11584
- Disable engine bonding on Gen12+ except TGL, RKL and ADL-S
Cross-subsystem Changes:
- Merges 'tip/locking/wwmutex' branch (core kernel tip)
- "mei: pxp: export pavp client to me client bus"
Core Changes:
- Update ttm_move_memcpy for async use (Thomas)
Driver Changes:
- Enable GuC submission by default on DG1 (Matt B)
- Add PXP (Protected Xe Path) support for Gen12 integrated (Daniele,
Sean, Anshuman)
See "drm/i915/pxp: add PXP documentation" for details!
- Remove force_probe protection for ADL-S (Raviteja)
- Add base support for XeHP/XeHP SDV (Matt R, Stuart, Lucas)
- Handle DRI_PRIME=1 on Intel igfx + Intel dgfx hybrid graphics setup (Tvrtko)
- Use Transparent Hugepages when IOMMU is enabled (Tvrtko, Chris)
- Implement LMEM backup and restore for suspend / resume (Thomas)
- Report INSTDONE_GEOM values in error state for DG2 (Matt R)
- Add DG2-specific shadow register table (Matt R)
- Update Gen11/Gen12/XeHP shadow register tables (Matt R)
- Maintain backward-compatible nested batch behavior on TGL+ (Matt R)
- Add new LRI reg offsets for DG2 (Akeem)
- Initialize unused MOCS entries to device specific values (Ayaz)
- Track and use the correct UC MOCS index on Gen12 (Ayaz)
- Add separate MOCS table for Gen12 devices other than TGL/RKL (Ayaz)
- Simplify the locking and eliminate some RCU usage (Daniel)
- Add some flushing for the 64K GTT path (Matt A)
- Mark GPU wedging on driver unregister unrecoverable (Janusz)
- Major rework in the GuC codebase, simplify locking and add docs (Matt B)
- Add DG1 GuC/HuC firmwares (Daniele, Matt B)
- Remember to call i915_sw_fence_fini on guc_state.blocked (Matt A)
- Use "gt" forcewake domain name for error messages instead of "blitter" (Matt R)
- Drop now duplicate LMEM uAPI RFC kerneldoc section (Daniel)
- Fix early tracepoints for requests (Matt A)
- Use locked access to ctx->engines in set_priority (Daniel)
- Convert gen6/gen7/gen8 read operations to fwtable (Matt R)
- Drop gen11/gen12 specific mmio write handlers (Matt R)
- Drop gen11 specific mmio read handlers (Matt R)
- Use designated initializers for init/exit table (Kees)
- Fix syncmap memory leak (Matt B)
- Add pretty printing for buddy allocator state debug (Matt A)
- Fix potential error pointer dereference in pinned_context() (Dan)
- Remove IS_ACTIVE macro (Lucas)
- Static code checker fixes (Nathan)
- Clean up disabled warnings (Nathan)
- Increase timeout in i915_gem_contexts selftests 5x for GuC submission (Matt B)
- Ensure wa_init_finish() is called for ctx workaround list (Matt R)
- Initialize L3CC table in mocs init (Sreedhar, Ayaz, Ram)
- Get PM ref before accessing HW register (Vinay)
- Move __i915_gem_free_object to ttm_bo_destroy (Maarten)
- Deduplicate frequency dump on debugfs (Lucas)
- Make wa list per-gt (Venkata)
- Do not define dummy vma in stack (Venkata)
- Take pinning into account in __i915_gem_object_is_lmem (Matt B, Thomas)
- Do not report currently active engine when describing objects (Tvrtko)
- Fix pdfdocs build error by removing nested grid from GuC docs (Akira)
- Remove false warning from the rps worker (Tejas)
- Flush buffer pools on driver remove (Janusz)
- Fix runtime pm handling in i915_gem_shrink (Maarten)
- Rework TTM object initialization slightly (Thomas)
- Use fixed offset for PTEs location (Michal Wa)
- Verify result from CTB (de)register action and improve error messages (Michal Wa)
- Fix bug in user proto-context creation that leaked contexts (Matt B)
- Re-use Gen11 forcewake read functions on Gen12 (Matt R)
- Make shadow tables range-based (Matt R)
- Ditch the i915_gem_ww_ctx loop member (Thomas, Maarten)
- Use NULL instead of 0 where appropriate (Ville)
- Rename pci/debugfs functions to respect file prefix (Jani, Lucas)
- Drop guc_communication_enabled (Daniele)
- Selftest fixes (Thomas, Daniel, Matt A, Maarten)
- Clean up inconsistent indenting (Colin)
- Use direction definition DMA_BIDIRECTIONAL instead of
PCI_DMA_BIDIRECTIONAL (Cai)
- Add "intel_" as prefix in set_mocs_index() (Ayaz)
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YWAO80MB2eyToYoy@jlahtine-mobl.ger.corp.intel.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a function for checking source MST support. Drop intel_dp->can_mst
and use intel_dp->mst_mgr.cbs to indicate the same. It's the single
point of truth without additional state variables. In code, "source
support" is also self-documenting as opposed to the vague "can mst".
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006101618.22066-1-jani.nikula@intel.com
Limit the supported UHBR rates based on the repeater support, if there
are repeaters.
This should be done in DP helper level, but that requires an overhaul of
the LTTPR handling, as the max rate is not enough to represent how
128b/132b rates may be masked along the way.
Curiously, the spec says:
* Shall be cleared to 00h when operating in 8b/10b Link Layer.
* Each LTTPR on the way back to the DPTX shall clear the bits that do
not correspond to the LTTPR's current bit rate.
It's rather vague if we can reliably use the field at this time due to
the wording "operating" and "current". But it would seem bizarre to have
to wait until trying to operate a 128b/132b link layer at a certain bit
rate to figure this out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007105727.18439-1-jani.nikula@intel.com
The UHBR check was using > instead of >=. Use the helper instead to
avoid mistakes. Also always use the non-UHBR values for HDMI.
v2: Use intel_crtc_has_dp_encoder() && intel_dp_is_uhbr() (Ville)
Fixes: 2817efaeb6 ("drm/i915/dg2: add SNPS PHY translations for UHBR link rates")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007124201.18686-1-jani.nikula@intel.com
As per the comment on top of acpi_evaluate_dsm():
| * Evaluate device's _DSM method with specified GUID, revision id and
| * function number. Caller needs to free the returned object.
We should free the returned object of acpi_evaluate_dsm() to avoid memory
leakage. Otherwise the kmemleak splat will be triggered at boot time (if we
compile kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE=y).
Fixes: 8e55f99c51 ("drm/i915: Invoke another _DSM to enable MUX on HP Workstation laptops")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906033541.862-1-yuzenghui@huawei.com
I suppose intel_dp_dump_link_status() might be useful for diagnosing
link training failures. Hoever we only call from the channel EQ phase
currently. Let's call it from the CR phase as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004170535.4173-6-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Unify all debug prints during link training to include information
on both the encoder and the LTTPR. We unify the format to something
like "[ENCODER:1:FOO][LTTPR 1] Something something". Though not
sure if those brackets around the dp_phy just make it look like
line noise? I'll accept suggestions on better formatting.
I'm slightly on the fence about also including the connector,
but technically only the DPRX is the SST connector (ie.
intel_dp->attached_connector). I suppose you could think of it
as the branch device/whatever in the topology, and we're training
the link leading to it. So that could argue for its inclusion.
But it's all getting a bit long alrady, so not going to do it
I think.
v2: Keep the connector name in the final passed/failed debug print
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004170535.4173-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we consider the max vswing reached when we transmit a
the max voltage level, but we don't consider pre-emphasis at all.
This kinda matches older DP specs that only had some vague text
about transmitting the maximum voltage swing. Latest versions
now say something vague about consider the sum of the vswing
and pre-emphasis fields in the ADJUST_REQUEST_LANE registers.
Very vague, and super confusing especially the fact that it
talks about transmitted voltgage swing in the same sentence
as it say to look at the requested values.
Also glanced at the link CTS spec, and that one seems to have
tests that assume contradicting behaviour. Some say to consider
just the vswing level we transmit, others say to check for
sum of transmitted vswing+preemph being 3.
So let's try to take some kind of sane middle ground here.
I think what could make sense is only consider max vswing
reached if MAX_SWING_REACHED==1 _and_ vswing+preemph==3.
That will allow things to go all the way up to vswing 3 +
pre-emph 0 or vswing 2 + pre-emph 1, depending on what
the maximum supported vswing is. Only considering the sum
of vswing+pre-emph doesn't make much sense to me since
we could terminate too early if the sink requests eg.
vswing 0 + pre-emph 3. And if we'd stick to the current
code we could terminate too early of the sink asks for
vswing 2 + pre-emph 0 when vswing level 3 is not supported.
Side note: I don't really understand why any of this stuff is
"specified" at all. There is already a limit of 5 attempts at
the same vswing+pre-emph level, and a total limit of 10
attempts. So might as well stick to the same max 5 attempts
across the board IMO.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004170535.4173-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The "digi_port" pointer can't be NULL and we have already dereferenced
it so checking for NULL is not necessary. Delete the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004103737.GC25015@kili
With patch "drm/i915/vbt: Fix backlight parsing for VBT 234+"
the size of bdb_lfp_backlight_data structure has been increased,
causing if-statement in the parse_lfp_backlight function
that comapres this structure size to the one retrieved from BDB,
always to fail for older revisions.
This patch calculates expected size of the structure for a given
BDB version and compares it with the value gathered from BDB.
Tested on Chromebook Pixelbook (Nocturne) (reports bdb->version = 221)
Fixes: d381baad29 ("drm/i915/vbt: Fix backlight parsing for VBT 234+")
Tested-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134606.227234-1-lma@semihalf.com
(cherry picked from commit 4378daf5d0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
(cherry picked from commit 7194dc998d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 989634fb49 ("drm/i915/audio: set HDA link parameters in
driver") makes HDMI audio on Lenovo P350 disappear.
So in addition to TGL, extend the logic to RKL to use BIOS provided
value to fix the regression.
Fixes: 989634fb49 ("drm/i915/audio: set HDA link parameters in driver")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906041300.508458-1-kai.heng.feng@canonical.com
(cherry picked from commit c6b40ee330)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since the VT-d vs. async flip issues are plaguing a wider range
of supported hw let's try to minimize the impact on normal
operation by flipping the relevant chicken bits on and off
as needed. I presume there is some power/perf impact on since
this is reducing some prefetching I think.
Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930190943.17547-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
When protected sufaces has flipped and pxp session is disabled,
display black pixels by using plane color CTM correction.
v2:
- Display black pixels in async flip too.
v3:
- Removed the black pixels logic for async flip. [Ville]
- Used plane state to force black pixels. [Ville]
v4 (Daniele): update pxp_is_borked check.
v5: rebase on top of v9 plane decryption moving the decrypt check
(Juston)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gaurav Kumar <kumar.gaurav@intel.com>
Cc: Shankar Uma <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924191452.1539378-15-alan.previn.teres.alexis@intel.com
Add support to enable/disable PLANE_SURF Decryption Request bit.
It requires only to enable plane decryption support when following
condition met.
1. PXP session is enabled.
2. Buffer object is protected.
v2:
- Used gen fb obj user_flags instead gem_object_metadata. [Krishna]
v3:
- intel_pxp_gem_object_status() API changes.
v4: use intel_pxp_is_active (Daniele)
v5: rebase and use the new protected object status checker (Daniele)
v6: used plane state for plane_decryption to handle async flip
as suggested by Ville.
v7: check pxp session while plane decrypt state computation. [Ville]
removed pointless code. [Ville]
v8 (Daniele): update PXP check
v9: move decrypt check after icl_check_nv12_planes() when overlays
have fb set (Juston)
v10 (Daniele): update PXP check again to match rework in earlier
patches and don't consider protection valid if the object has not
been used in an execbuf beforehand.
Cc: Bommu Krishnaiah <krishnaiah.bommu@intel.com>
Cc: Huang Sean Z <sean.z.huang@intel.com>
Cc: Gaurav Kumar <kumar.gaurav@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> #v9
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924191452.1539378-14-alan.previn.teres.alexis@intel.com
LTTPRs should support per-lane drive settings I think, and even if
they don't they should implement their own fallback logic to determine
suitable common drive settings to use for all the lanes.
v2: Actually check the correct thing
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-11-ville.syrjala@linux.intel.com
Adjust the link training code to accommodate per-lane drive settings,
if supported by the platform. Actually enabling this will involve
some changes to each platform's .set_signal_level() implementation,
so for the moment all supported platforms will keep using the current
codepath that just uses the same drive settings for all the lanes.
v2: Fix min() vs. max() fumble
v3: Compact the debug print to a single line
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-10-ville.syrjala@linux.intel.com
In order to have per-lane drive settings we need intel_ddi_level()
to accept the lane as a parameter. That is, the eventual goal is to
call intel_ddi_level() once for each lane. For now we just pass in
a hardcoded 0 and use the same settings for every lane. Ie. no
change in behaviour yet.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-9-ville.syrjala@linux.intel.com
Since intel_ddi_level() now looks at the buf_trans table there's
no point in having intel_ddi_hdmi_num_entries() around. Just
roll the necessary bits of locic into
intel_ddi_hdmi_level()/intel_ddi_level().
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-8-ville.syrjala@linux.intel.com
All callers of intel_ddi_level() duplicate the check+WARN
to make sure the returned level is actually present in the
appropriate buf_trans table. Let's push that stuff into
intel_ddi_level() so the callers don't have to worry about it.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-7-ville.syrjala@linux.intel.com
Currently .set_signal_levels() is only used by encoders in DP mode.
For most modern platforms there is no essential difference between
DP and HDMI, and both codepaths just end up calling the same function
under the hood. Let's get remove the need for that extra indirection
by moving .set_signal_levels() into the encoder from intel_dp.
Since we already plumb the crtc_state/etc. into .set_signal_levels()
the code will do the right thing for both DP and HDMI.
HSW/BDW/SKL are the only platforms that need a bit of care on
account of having to preload the hardware buf_trans register
with the full set of values. So we must still remember to call
hsw_prepare_{dp,hdmi}_ddi_buffers() to do said preloading, and
.set_signal_levels() will just end up selecting the correct entry
for DP, and also setting up the iboost magic for both DP and HDMI.
Note that previously on HSW/BDW/SKL we did write to DDI_BUF_CTL to
select the correct entry until link training started, now that we
call .set_signal_levels() already from hsw_ddi_pre_enable_dp() that
is no longer the case. But it's all safe now that the
intel_ddi_init_dp_buf_reg() call was hoisted up and it no longer
sets up the DDI_BUF_CTL_ENABLE bit (that is still deferred until
link training).
v2: Rebase due to has_{iboost,buf_trans_select}()
Add some notes about the DDI_BUF_CTL situation on HSW/BDW/SKL (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-4-ville.syrjala@linux.intel.com
Add a small helper to determine if DDI_BUF_CTL uses the
DDI_BUF_TRANS_SELECT field, and whether we have the
accompanying DDI_BUF_TRANS table in the hardware.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The DP spec says:
"If the receiver keeps the same value in the ADJUST_REQUEST_LANEx_y
register(s) while the LANEx_CR_DONE bits remain unset, the transmitter
must loop four times with the same voltage swing. On the fifth time,
the transmitter must down-shift to the lower bit rate and must repeat
the CR-lock training sequence as described below."
Lets fix the code to follow that instead of terminating after five
times of transmitting the same signal levels. The text in spec feels
a little bit ambiguous still, but this is my best guess at its meaning.
As a bonus this also gets rid of the train_set[0] stuff which
would not work for per-lane drive settings anyway.
Cc: Imre Deak <imre.deak@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001160826.17080-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While sanitizing the hardware state we're currently forcing
the pipe bottom color legacy csc/gamma bits on. That is not a
good idea as BIOSen are likely to leave gabage in the LUTs and
so doing this causes ugly visual glitches if and when the
planes covering the background get disabled. This was exactly
the case on this Dell Precision 5560 tgl laptop.
On icl+ we don't normally even use these legacy bits
anymore and instead use their GAMMA_MODE counterparts.
On earlier platforms the bits are used, but we still
shouldn't force them on without knowing what's in the LUT.
So two options, get rid of the whole thing, or do what
intel_color_commit() does to make sure the bottom color state
matches whatever out hardware readout produced. I chose the
latter since it'll match what happens on older platforms when
the primary plane gets turned off. In fact let's just call
intel_color_commit(). It'll also do some CSC programming but
since we don't have readout for that it'll actually just set
to all zeros. So in the unlikely case of CSC actually being
enabld by the BIOS we'll end up with all black until the first
atomic commit happens.
Still not totally sure what we should do about color management
features here in general. Probably the safest thing would be to
force everything off exactly at the same time when we disable
the primary plane as there is no guarantees that whatever the
LUTs/CSCs contain make any sense whatsoever without the
specific pixel data in the BIOS fb. And if we preserve the
primary plane then we should disable the color management
features exactly when the primary plane fb contents first
changes since the new content assumes more or less no
transformations. But of course synchronizing front buffer
rendering with anything else is a bit hard...
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3534
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928185105.3030-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
"CRTC fixup failed" is probably leftovers from pre-atomic days
when there was an actual fixup() function. Let's unify the debug
messages between encoder vs. crtc compute_config() calls.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930104133.30854-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Having two functions for this seems like excess duplication and
parameter juggling. Merge them together.
While at it, drop the extra error message, as wait_for_payload_credits()
already prints an error, and switch from incidental -EPERM (i.e. -1) to
actual error codes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f74f7462a36e76070db6b4c01616d0eb663b9938.1633000838.git.jani.nikula@intel.com
Move assert_panel_unlocked() to intel_pps.c and rename
assert_pps_unlocked(). Keep the functionality and the assert code
together.
There's still a bit of a split between the eDP PPS usage in intel_pps.c
and all the other PPS usage, and assert_pps_unlocked() is arguably more
related to the latter. However, intel_pps.c is the best fit for anything
touching the PPS registers.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a9b77692a145891789eefb0447e082cfc22aaa85.1632992608.git.jani.nikula@intel.com
With all the recent fixes PSR2 is properly working in Alderlake-P but
due to some issues that don't have software workarounds it will not be
supported in display steppings older than B0.
Even with this patch PSR2 will no be enabled by default in ADL-P, it
still requires enable_psr2_sel_fetch to be set to true, what some
of our tests does.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-7-jose.souza@intel.com
The Wa_14014971508 is required to fix scanout when a feature that i915
do not support is enabled and this feature is not planned to be enabled
for adlp.
Keeping this workaround enabled can badly hurt power-savings when
a full frame fetch is required(see psr2_sel_fetch_plane_state_supported()
and psr2_sel_fetch_pipe_state_supported()).
Here a example that could badly hurt power-savings, userspace does
a page flip to a rotated plane, so CONTINUOS_FULL_FRAME set.
But then for a whole 30 seconds nothing in the screen requires updates
but because CONTINUOS_FULL_FRAME is set, it will not go into DC5/DC6.
Reverting Wa_14014971508 fixes that, as only a single frame will be
sent and then display can go to DC5/DC6 for those 30 seconds of
idleness.
BSpec: 54369
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-6-jose.souza@intel.com
Legacy cursor APIs are handled by intel_legacy_cursor_update(), that
calls drm_atomic_helper_update_plane() when going through the
slow/atomic path to update cursor, what was the case for PSR2
selective fetch.
drm_atomic_helper_update_plane() sets
drm_atomic_state->legacy_cursor_update to true when updating the
cursor plane, to allow several cursor updates to happen within the
same frame, as userspace does that.
If drivers waited for a vblank increment at the end of every cursor
movement that would cause a visible lag in the cursor.
But this optimization do not properly work with PSR2 selective fetch
dirt area calculation, for example if within a single frame the cursor
had 3 moves the final dirt area programmed to PSR2_MAN_TRK_CTL would
be based in the second movement as old state and third movement as new
state, not updating the area where cursor was in the first state.
So here switching back to the fast path approach in
intel_legacy_cursor_update() and handling cursor movements as
frontbuffer rendering(psr_force_hw_tracking_exit()), that is not the
most optimal for power-savings but is the solution that we have until
mailbox style updates is implemented.
Also removing the cursor workaround as not it is properly undestand
the issue and is know that it will never cover all the cases.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-5-jose.souza@intel.com
When PSR2 selective fetch is enabled writes to CURSURFLIVE alone do
not causes the panel to be updated when doing frontbuffer rendering.
From what I was able to figure from experiments the writes to
CURSURFLIVE takes PSR2 from deep sleep but panel is not updated
because PSR2_MAN_TRK_CTL has no start and end region set.
As we don't have the dirt area from current flush and invalidate API
and even if we did userspace could do several draws to frontbuffer and
we would need a way to append all the damaged areas of all the draws
that need to be part of next frame.
So here only programing PSR2_MAN_TRK_CTL to do a single full frame
fetch.
It is a safe approach as if scanout is in the visible area
the single full frame will only be visible for hardware in the next
frame because of the double buffering, and if scanout is in vblank
area it will be draw in the current frame.
No need to disable PSR and wait a few miliseconds to enable it again.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-4-jose.souza@intel.com
This unnecessary flushes are hurting power-savings are it causes
features like PSR, FBC and DRRS to disable it self to handle
frontbuffer rendering, below some explanation of why each removed
call is not necessary.
The flush in intel_prepare_plane_fb() is not required as framebuffer
will be flipped and power-saving features do the proper flip handling
in hardware.
intel_find_initial_plane_obj() flush is not required because it is
only executed during driver load and at this point the power-saving
features are not even enabled.
And the last one intelfb_create(), is also not required as at this
point the fbdev was just allocated, userspace will draw on
it what will trigger frontbuffer invalidates and flushes later on.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-3-jose.souza@intel.com
We are still missing the PSR2 selective fetch handling of multi-planar
formats but until proper handle is added we can workaround it by
doing full frames fetch when state has such formats.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-2-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
PSR2 selective is not supported over rotated and scaled planes.
We had the rotation check in intel_psr2_sel_fetch_config_valid()
but that code path is only execute when a modeset is needed and
those plane parameters can change without a modeset.
Pipe selective fetch restrictions are also needed, it could be added
in intel_psr_compute_config() but pippe scaling is computed after
it is executed, so leaving as is for now.
There is no much loss in this approach as it would cause selective
fetch to not enabled as for alderlake-P and newer will cause it to
switch to PSR1 that will have the same power-savings as do full pipe
fetch.
Also need to check those restricions in the second
for_each_oldnew_intel_plane_in_state() loop because the state could
only have a plane that is not affected by those restricitons but
the damaged area intersect with planes that has those restrictions,
so a full pipe fetch is required.
v2:
- also handling pipe restrictions
BSpec: 55229
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> # v1
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930001409.254817-1-jose.souza@intel.com
Get rid of the local copies and pointers of intel_dp->DP and
instead just poke at it directly. Makes it much easier to see
where it actually gets used/modified.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Setting DP_PORT_EN in intel_dp->DP is already handled by
intel_dp_enable_port() so there is no point in setting it also
from the link training code.
For DDI platforms a bit with that name doesn't even exist. The
counterpart is DDI_BUF_CTL_ENABLE, which is already set up by
intel_ddi_prepare_link_retrain(). Fortunately it is the same bit
so there was no harm in doing this from the platform independent
code as well. But it's just confusing when platform independent
code sets platform specific bits in intel_dp->DP. Just get rid
of it.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak.intel.com>
I want intel_dp->DP to be fully populated by the time the
initial vswing programming happens. To that end move the
intel_ddi_init_dp_buf_reg() call to an earlier spot.
Additionally we don't want intel_ddi_init_dp_buf_reg() to
set DDI_BUF_CTL_ENABLE since the port should only get enabled
at the start of link training (see intel_ddi_prepare_link_retrain()).
So any earlier write to the register should not set the enable bit.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we clear the leftover vswing/preemphasis values only
at the start of link training. That means the initial vswing
programming performed during modeset is going to use stale values
left over from the previous link training sequence, and then at
the start of link training we're going to reset the levels back
to 0. Seems much better to make sure we start with level 0 from
the get go.
Additionally if LTTPRs are present the leftover vswing/preemphasis
values are those of the last link in the chain, so not the values
that our PHY is even using after a successful link training sequence.
So let's make sure everything is cleared up before we start
programming anything.
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
With patch "drm/i915/vbt: Fix backlight parsing for VBT 234+"
the size of bdb_lfp_backlight_data structure has been increased,
causing if-statement in the parse_lfp_backlight function
that comapres this structure size to the one retrieved from BDB,
always to fail for older revisions.
This patch calculates expected size of the structure for a given
BDB version and compares it with the value gathered from BDB.
Tested on Chromebook Pixelbook (Nocturne) (reports bdb->version = 221)
Fixes: d381baad29 ("drm/i915/vbt: Fix backlight parsing for VBT 234+")
Tested-by: Lukasz Majczak <lma@semihalf.com>
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134606.227234-1-lma@semihalf.com
Ensure i915_vma_pin_iomap and vma_unpin are done with dpt->obj lock held.
I don't think there's much of a point in merging intel_dpt_pin() with
intel_pin_fb_obj_dpt(), they touch different objects.
Changes since v1:
- Fix using the wrong pointer to retrieve error code (Julia)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929085950.3063191-1-maarten.lankhorst@linux.intel.com
Let's not configure the single transcoder's TRANSCONF multiple
times with bigjoiner. No real harm I suppose but since we already
have the bigjoiner if statement directly above might as well suck
this in there and skip the redundant programming.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Adjust the HSW+ transcoder state readout to just read through
all the possible transcoders for the pipe, and stuff the results
in a bitmask.
We can conveniently cross check the bitmask for invalid
combinations of enabled transcoders, and later we can easily
extend the bitmask readout to handle the bigjoiner case.
One slight change in behaviour is that we no longer read out
the AONOFF->force_pfit.pfit bit for all the enabled "panel
transcoders". But having more than one enabled would anyway
be illegal so no big loss. Also the AONOFF selection should
only ever be used on HSW, which only has the EDP transcoder
an no DSI transcoders.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-10-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
FBC+Yf tiling seems to work just fine, and unlike with linear
the hardware does appear to correctly calculate the CFB stride
with using the override stride on both cfl and glk. So no need
for any additional tweaks.
Cc: Uma Shankar <uma.shankar@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210924141330.1515-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Stop using HBR2/3 support as a proxy for TPS3/4 support.
The two are no longer 1:1 in the hardware, arguably they
never were due to HSW ULX which does support TPS3 while
being limited to HBR1.
In more recent times GLK gained support for TPS4 while
being limited to HBR2. And on CNL+ some ports support
HBR3 while others are limited to HBR2, but all ports
support TPS4.
v2: s/INTEL_GEN/DISPLAY_VER/
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929162404.6717-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
When using a panel with a fixed mode we don't change the refresh
rate of the display. Reject any user requested mode which doesn't
match that fixed refresh rate.
Unfortunately when Xorg sees the scaling_mode property on the
connecor it likes to automagically cook up modes whose refresh
rate is a fair bit off from the fixed refresh rate we use. So
we have to give it some extra latitude so that we don't start to
reject all of it.
v2: sDVO now uses intel_panel_compute_config() too
v3: Add a debug message to inform the user what happened
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929184536.8332-1-ville.syrjala@linux.intel.com
Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.
Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.
v2: Use intel_panel_compute_config() with sDVO
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
When using a fixed mode we won't change the refresh rate ever.
So filter out all modes that don't match the fixed_mode's refresh
rate.
I'm going to declare the "rounded to nearest Hz refresh
rates must match" approach good enough for now.
Note that we could start supporting multiple refresh rates
with panels that can do it, but that would mean replacing
the single fixed mode concept with a list of fixed modes.
Then we could look for the closest match to the user's
requested refresh rate and use that. But all of that would
be a fair bit of work so we'll leave it for later.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2939
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3969
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All fixed mode panels should behave the same way when it comes to mode
filtering. Reuse the intel_panel_mode_valid() for all of them.
This changes the behaviour to match what we do for eDP, ie.
reject anything that doesn't exactly match the fixed mode
dimensions. Users can still manually provide different
sized modes which will be handled by the panel fitter just
as before. The difference is that we can no longer report
funny modes in the connector's mode list.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923200109.4459-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The PHY ownership release->AUX PW disable steps during a modeset
disable->PHY disconnect sequence can hang the system if the PHY
disconnect happens after disabling the PHY's PLL. The spec doesn't
require a specific order for these two steps, so this issue is still
being root caused by HW/FW teams. Until that is found, let's make
sure the disconnect happens before the PLL is disabled, and do this on
all platforms for consistency.
v2: Add a TODO comment to remove the w/a once the issue is root
caused/fixed. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-7-imre.deak@intel.com
After the previous patch the driver holds a power domain blocking
TC-cold whenever the port is locked, so we can remove the extra blocking
around the lock/unlock sequence.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-13-imre.deak@intel.com
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
While a TypeC port mode is locked a DISPLAY_CORE power domain reference
is held, which implies a runtime PM ref. By removing the ICL !legacy
port special casing, a TC_COLD_OFF power domain reference will be taken
for such ports, which also translates to a runtime PM ref on that
platform. A follow-up change will stop holding the DISPLAY_CORE power
domain while the port is locked.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-11-imre.deak@intel.com
For the ADL-P TBT mode the spec doesn't require blocking TC-cold by
using the legacy AUX power domain. To avoid the timeouts that this would
cause during PHY disconnect/reconnect sequences (which will be more
frequent after a follow-up change) use the TC_COLD_OFF power domain in
TBT mode on all platforms. On TGL this power domain blocks TC-cold via a
PUNIT command, while on other platforms the domain just takes a runtime
PM reference.
If the HPD live status indicates that the port mode needs to be reset
- for instance after switching from TBT to a DP-alt sink - still take
the AUX domain, since the IOM firmware handshake requires this.
v2: Rebased on v2 of the previous patch.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-5-imre.deak@intel.com
A follow-up change will select the TC-cold blocking power domain based
on the TypeC mode, prepare for that here.
Also bring intel_tc_cold_requires_aux_pw() earlier to its logical place
for readability.
No functional change.
v2: Add code comment about IOM reg accesses in TCCOLD. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-4-imre.deak@intel.com
A follow-up change will start to disconnect/re-connect PHYs around AUX
transfers and modeset enable/disables. To prepare for that add a new
TypeC PHY disconnected mode, to help tracking the TC-cold blocking power
domain status (no power domain in disconnected state, mode dependent
power domain in connected state).
v2: Move the !disconnected mode and phy-owned asserts in
__intel_tc_port_lock() later in the patchset, when the asserts will
hold. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-3-imre.deak@intel.com
A follow-up patch will disconnect/reconnect PHYs around AUX transfers
and modeset enable/disables. To prepare for that and make things
consistent for all TypeC modes stop connecting the PHY in legacy mode
without a sink being connected. This was done before since in legacy
mode the PHY is dedicated to display usage, so there was no point in
disconnecting it. However after the follow-up changes the TC-cold
blocking power domains will be held as long as the PHY is in the
connected state, so we'll need to disconnect/re-connect the PHY in all
TypeC modes to allow for power saving.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-7-imre.deak@intel.com
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
On ADL-P the PHY ready/complete flag is always set even in TBT-alt mode.
To avoid taking the PHY ownership and the following spurious "PHY sudden
disconnect" messages on this platform when connecting the PHY in TBT
mode, check if there is any DP-alt or legacy sink connected before
taking the ownership.
v2: (Jose)
- Fix debug message clarifying that a TBT sink can be connected.
- Add comments describing the PHY complete HW flag semantic differences
between adl-p and other platforms.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-2-imre.deak@intel.com
Waiting for the PHY complete flag to clear when releasing the PHY
ownership was add in
commit ddec362724 ("drm/i915: Wait for TypeC PHY complete flag to clear in safe mode")
This isn't required by the spec, the vague idea was to make the
handshake with the firmware more robust, without actual evidence for
when it would be needed. Checking this again, the flag doesn't clear on
ICL until after the PHY's PLL is disabled and the flag is permanently
set on ADL-P. To avoid the spurious timeout messages in dmesg, just
remove this wait.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-4-imre.deak@intel.com
On ADL-P the PHY ready (aka status complete on other platforms) flag is
always set, besides when a DP-alt, legacy sink is connected also when a
TBT sink is connected or nothing is connected. So assume the PHY to be
connected when both the TBT live status and PHY ready flags are set.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-3-imre.deak@intel.com
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
Display underrun in HDR mode when cursor is enabled.
RTL fix will be implemented CLKGATE_DIS_PSL_A bit 28-46520h.
As per W/A 1604331009, Disable cursor clock gating in HDR mode.
Bspec : 33451
Changes since V6:
- Address checkpatch warnings
- Bit ordering
Changes since V5:
- replace intel_de_read with intel_de_rmw - Jani
Changes since V4:
- Added WA needed check - Ville
- Replace BIT with REG_BIT - Ville
- Add WA enable/disable support back which was
added in V1 - Ville
Changes since V3:
- Disable WA when not in HDR mode or cursor plane
not active - Ville
- Extract required args from crtc_state - Ville
- Create HDR mode API using bdw_set_pipemisc ref - Ville
- Tested with HDR video as well full setmode, WA
applies and disables
Changes since V2:
- Made it general gen11 WA
- Removed WA needed check
- Added cursor plane active check
- Once WA enable, software will not disable
Changes since V1:
- Modified way CLKGATE_DIS_PSL bit 28 was modified
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929052442.2543054-1-tejaskumarx.surendrakumar.upadhyay@intel.com
This moves one wrapper from the pm->display side, and creates
wrappers for all the others, this should simplify things later.
One thing to note is that the code checks the existence of some
of these ptrs, so the wrappers are a bit complicated by that.
Suggested by Jani.
v2: fixup warnings in wrong place error.
v3 by Jani: fix intel_compute_global_watermarks() return value check
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ee2760c45896568c9dd9114a575509619bd44ef2.1632869550.git.jani.nikula@intel.com
The right parameter that selects second dsc engine is dsc_split.
Hence use dsc_split instead of slice_count while selecting the
cdclk in order to accommodate 1ppc limitaion of vdsc.
Fixes: fe01883fdc ("drm/i915: Get proper min cdclk if vDSC enabled")
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915054338.29869-1-vandita.kulkarni@intel.com
Commit 989634fb49 ("drm/i915/audio: set HDA link parameters in
driver") makes HDMI audio on Lenovo P350 disappear.
So in addition to TGL, extend the logic to RKL to use BIOS provided
value to fix the regression.
Fixes: 989634fb49 ("drm/i915/audio: set HDA link parameters in driver")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906041300.508458-1-kai.heng.feng@canonical.com
On FBC1 we can specify an arbitrary cfb stride. The hw will
simply throw away any compressed line that would exceed the
specified limit and keep using the uncompressed data instead.
Thus we can allow arbitrary compression limits.
The one thing we have to keep in mind though is that the cfb
stride is specified in units of 32B (gen2) or 64B (gen3+).
Fortunately X-tile is already 128B (gen2) or 512B (gen3+) wide
so as long as we limit outselves to the same 4x compression
limit that FBC2 has we are guaranteed to have a sufficiently
aligned cfb stride.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921152517.803-5-ville.syrjala@linux.intel.com
There's some kind of weird corner cases in FBC which requires
FBC segments to be separated by at least one extra cacheline.
Make sure that is present.
v2: Respin to fit in with skl_fbc_min_cfb_stride()
v3: Make it build
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921181245.15091-1-ville.syrjala@linux.intel.com
Apply the same 512 byte FBC segment alignment to glk+ as we use
on skl+. The only real difference is that we now have a dedicated
register for the FBC override stride. Not 100% sure which
platforms really need the 512B alignment, but it's easiest
to just do it on everything.
Also the hardware no longer seems to misclaculate the CFB stride
for linear, so we can omit the use of the override stride for
linear unless the stride is misaligned.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921152517.803-3-ville.syrjala@linux.intel.com
The code to calculate the cfb stride/size is a bit of mess.
The cfb size is getting calculated based purely on the plane
stride and plane height. That doesn't account for extra
alignment we want for the cfb stride. The gen9 override
stride OTOH is just calculated based on the plane width, and
it does try to make things more aligned but any extra alignment
added there is not considered in the cfb size calculations.
So not at all convinced this is working as intended. Additionally
the compression limit handling is split between the cfb allocation
code and g4x_dpfc_ctl_limit() (for the 16bpp case), which is just
confusing.
Let's streamline the whole thing:
- Start with the plane stride, convert that into cfb stride (cfb is
always 4 bytes per pixel). All the calculations will assume 1:1
compression limit since that will give us the max values, and we
don't yet know how much stolen memory we will be able to allocate
- Align the cfb stride to 512 bytes on modern platforms. This guarantees
the 4 line segment will be 512 byte aligned regardles of the final
compression limit we choose later. The 512 byte alignment for the
segment is required by at least some of the platforms, and just doing
it always seems like the easiest option
- Figure out if we need to use the override stride or not. For X-tiled
it's never needed since the plane stride is already 512 byte aligned,
for Y-tiled it will be needed if the plane stride is not a multiple
of 512 bytes, and for linear it's apparently always needed because the
hardware miscalculates the cfb stride as PLANE_STRIDE*512 instead of
the PLANE_STRIDE*64 that it use with linear.
- The cfb size will be calculated based on the aligned cfb stride to
guarantee we actually reserved enough stolen memory and the FBC hw
won't end up scribbling over whatever else is allocated in stolen
- The compression limit handling we just do fully in the cfb allocation
code to make things less confusing
v2: Write the min cfb segment stride calculation in a more
explicit way to make it clear what is going on
v3: Remeber to update fbc->limit when changing to 16bpp
Reviewed-by: Uma Shankar <uma.shankar@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210923042151.19052-1-ville.syrjala@linux.intel.com
PSR always had a requirement to only be enabled if there is active
planes but not following that never caused any issues.
But that changes in Alderlake-P, leaving PSR enabled without
active planes causes transcoder/port underruns.
Similar behavior was fixed during the pipe disable sequence by
commit 84030adb9e ("drm/i915/display: Disable audio, DRRS and PSR before planes").
intel_dp_compute_psr_vsc_sdp() had to move from
intel_psr_enable_locked() to intel_psr_compute_config() because we
need to be able to disable/enable PSR from atomic states without
connector and encoder state.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
We were not completely following the selective fetch programming
sequence, here some things we were doing wrong:
- not programming plane selective fetch a PSR2_MAN_TRK_CTL registers
when doing a modeset
- programming PSR2_MAN_TRK_CTL out of vblank
With this changes the last remainig underrun found in Alderlake-P is
fixed.
Bspec: 55229
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-2-jose.souza@intel.com
Specification asks for DC_STATE_DEBUG_MASK_CORES to be set for all
platforms that supports DMC, not only for geminilake and broxton.
While at is also taking the oportunity to simply the code.
BSpec: 7402
BSpec: 49436
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-1-jose.souza@intel.com
Add support for remapping CCS FBs on ADL-P to remove the restriction
of the power-of-two sized stride and the 2MB surface offset alignment
for these FBs.
We can only remap the tiles on the main surface, not the tiles on the
CCS surface, so userspace has to generate the CCS surface aligning to
the POT size padded main surface stride (by programming the AUX
pagetable accordingly). For the required AUX pagetable setup, this
requires that either the main surface stride is 8 tiles or that the
stride is 16 tiles aligned (= 64 kbytes, the area mapped by one AUX
PTE).
v2:
- Init intel_remapped_info::plane_alignment only for remapped views and
do this from intel_fb_view_init().
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-6-imre.deak@intel.com
Atm the DPT object can accommodate only one VMA, so the VMA offset will
be always 0. Add an assert for this.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-4-imre.deak@intel.com
At the moment CCS FB strides must be power-of-two sized, but a follow-up
change will add support remapping these FBs, allowing the FB passed in
by userspace to have a non-POT sized stride. For these remapped FBs we
can only remap the main surface, not the CCS surface. This means that
userspace has to always generate the CCS surface aligning to the POT
stride padded main surface (by setting up the CCS AUX pagetables
accordingly). Adjust the CCS surface stride check to enforce this.
No functional change.
v2:
- Fix the gen12_ccs_aux_stride() is not static sparse warning.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-3-imre.deak@intel.com
The tile size for all surface types is 4 kbyte (or 2 kbyte on old
platforms), with the exception of the TGL/ADL CCS surface where the tile
size is 64 bytes. To be able to remap CCS FBs the CCS surface tile needs
to be defined as 4 kbyte as well (the granularity of GTT pages in a
remapped view).
The only place using the dimension of the 64 byte CCS area is the initial
check for the main vs. CCS plane origin coordinate match. To prepare for
adding support for remapping CCS FBs let's call the 64 byte CCS area a
'tile block' and add a helper to retrieve the dimensions for it.
No functional change.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-2-imre.deak@intel.com
Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.
Bspec: 64631
v2: Use the new derating value only for ADL-P(MattR)
Fixes: 4d32fe2f14 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
(cherry picked from commit f6d66fc8cf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
128b/132b has a separate transcoder DDI mode, which also requires the
MST transport select to be set. Note that we'll use DP MST also for
single-stream 128b/132b.
Having the FDI and 128b/132b modes share the register mode value
complicates things a bit.
v2:
- Use HAS_DP20 abstraction for 128b/132b mode (Ville)
- Use intel_dp_is_uhbr() helper
Bspec: 50493
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/279bfbd979e0256fae13a5231e07e2f4fb665c07.1631191763.git.jani.nikula@intel.com
Wa_16014451276 fixes the starting coordinate for PSR2 selective
updates. CHICKEN_TRANS definition of the workaround bit has a wrong
name based on workaround definition and HSD.
Wa_14014971508 allows the screen to continue to be updated when
coming back from DC5/DC6 and SF_SINGLE_FULL_FRAME bit is not kept
set in PSR2_MAN_TRK_CTL.
Wa_16012604467 fixes underruns when exiting PSR2 when it is in one
of its internal states.
Wa_14014971508 is still in pending status in BSpec but by
the time this is reviewed and ready to be merged it will be finalized.
v2:
- renamed register to ADLP_1_BASED_X_GRANULARITY
- added comment about all ADL-P supported panels being 1 based X
granularity
BSpec: 54369
BSpec: 50054
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-5-jose.souza@intel.com
drm_atomic_helper_damage_iter_init() + drm_atomic_for_each_plane_damage()
returns the full plane area in case no damaged area was set by
userspace or it was discarted by driver.
This is important to fix the rendering of userspace applications that
does frontbuffer rendering and notify driver about dirty areas but do
not set any dirty clips.
With this we don't need to worry about to check and mark the whole
area as damaged in page flips.
Another important change here is the move of
drm_atomic_add_affected_planes() call, it needs to called late
otherwise the area of all the planes would be added to pipe_clip and
not saving power.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-4-jose.souza@intel.com
Not sure why but when moving the cursor fast it causes some artifacts
of the cursor to be left in the cursor path, adding some pixels above
the cursor to the damaged area fixes the issue, so leaving this as a
workaround until proper fix is found.
This is reproducile on TGL and ADL-P.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-3-jose.souza@intel.com
BSpec states that the minimum number of frames before selective update
is 2, so making sure this minimum limit is fulfilled.
BSpec: 50422
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-2-jose.souza@intel.com
The release notes mentions that this version-
1. Fix for unblock indication to punit.
2. Robustness fix for DC6/6v abort scenarios.
Cc: Imre Deak <Imre Deak <imre.deak@intel.com>>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914215732.67135-2-anusha.srivatsa@intel.com
Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.
Bspec: 64631
v2: Use the new derating value only for ADL-P(MattR)
Fixes: 4d32fe2f14 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Users reported that after commit 2bbd6dba84 ("drm/i915: Try to use
fast+narrow link on eDP again and fall back to the old max strategy on
failure"), the screen starts to have wobbly effect.
Commit a5c936add6 ("drm/i915/dp: Use slow and wide link training for
everything") doesn't help either, that means the affected eDP 1.2 panels
only work with max params.
So use max params for panels < eDP 1.4 as Windows does to solve the
issue.
v3:
- Do the eDP rev check in intel_edp_init_dpcd()
v2:
- Check eDP 1.4 instead of DPCD 1.1 to apply max params
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3714
Fixes: 2bbd6dba84 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure")
Fixes: a5c936add6 ("drm/i915/dp: Use slow and wide link training for everything")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820075301.693099-1-kai.heng.feng@canonical.com
(cherry picked from commit d7f213c131)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
After DPRX link training, intel_dp_link_train_phy() did not
return the training result properly. If link training failed,
i915 driver would not run into link train fallback function.
And no hotplug uevent would be received by user space application.
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706152541.25021-1-shawn.c.lee@intel.com
(cherry picked from commit dab1b47e57)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On some Cherry Trail devices, DisplayPort over Type-C is supported through
a USB-PD microcontroller (e.g. a fusb302) + a mux to switch the superspeed
datalines between USB-3 and DP (e.g. a pi3usb30532). The kernel in this
case does the PD/alt-mode negotiation itself, rather then everything being
handled in firmware.
So the kernel itself picks an alt-mode, tells the Type-C "dongle" to switch
to DP mode and sets the mux accordingly. In this setup the HPD pin is not
connected, so the i915 driver needs to respond to a software event and scan
the DP port for changes manually.
This commit adds support for this. Together with the recent addition of
DP alt-mode support to the Type-C subsystem this makes DP over Type-C
work on these devices.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-7-hdegoede@redhat.com
On Intel platforms we know that the ACPI connector device
node order will follow the order the driver (i915) decides.
The decision is made using the custom Intel ACPI OpRegion
(intel_opregion.c), though the driver does not actually know
that the values it sends to ACPI there are used for
associating a device node for the connectors, and assigning
address for them.
In reality that custom Intel ACPI OpRegion actually violates
ACPI specification (we supply dynamic information to objects
that are defined static, for example _ADR), however, it
makes assigning correct connector node for a connector entry
straightforward (it's one-on-one mapping).
Changes in v2 (Hans de goede):
- Take a reference on the fwnode which we assign to the connector,
for ACPI nodes this is a no-op but in the future we may see
software-fwnodes assigned to connectors which are ref-counted.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-6-hdegoede@redhat.com
On some MST docking stations, rx_info can only be read after
RepeaterAuth_Send_ReceiverID_List and the RxStatus READY bit is set
otherwise the read will return -EIO.
This behavior causes the mst stream type1 capability test to fail to
read rx_info and determine if the topology supports type1 and fallback
to type0.
To fix this, check for type1 capability when we receive rx_info within
the AKE flow when we read RepeaterAuth_Send_ReceiverID_List instead
of an explicit read just for type1 capability checking.
This does require moving where we set stream_types to after
hdcp2_authenticate_sink() when we get rx_info but this occurs before we
do hdcp2_propagate_stream_management_info.
Also, legacy HDCP 2.0/2.1 are not type 1 capable either so check for
that as well.
Changes since v5:
- rename intel_set_stream_types() to intel_hdcp_prepare_streams()
(Anshuman)
Changes since v4:
- move topology_type1_capable to intel_digital_port and rename it as
hdcp_mst_type1_capable (Anshuman)
- make a helper function intel_set_stream_types() to set stream types
in hdcp2_authenticate_and_encrypt() (Anshuman)
- break on failure to set stream types and retry instead of returning
- remove no longer used declaration for streams_type1_capable()
Changes since v2:
- Remove no longer used variables in _intel_hdcp2_enable()
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-4-juston.li@intel.com
When reading RepeaterAuth_Send_ReceiverID_List, RxInfo is read by itself
once to retrieve the DEVICE_COUNT to calculate the size of the
ReceiverID list then read a second time as a part of reading ReceiverID
list.
On some MST docking stations, RxInfo can only be read after the RxStatus
READY bit is set otherwise the read will return -EIO. The spec states that
the READY bit should be cleared as soon as RxInfo has been read.
In this case, the first RxInfo read succeeds but after the READY bit is
cleared, the second read fails.
Fix it by reading RxInfo once and storing it before reading the rest of
RepeaterAuth_Send_ReceiverID_List once we know the size.
Modify get_receiver_id_list_size() to read and store RxInfo in the
message buffer and also parse DEVICE_COUNT so we know the size of
RepeaterAuth_Send_ReceiverID_List.
Afterwards, retrieve the rest of the message at the offset for
seq_num_V.
Changes in v5:
- Don't change the offset define for Send_ReceiverID_List
When reading, update message offset to account for RxInfo being read
Changes in v4:
- rebase and edit commit message
Changes in v3:
- remove comment
Changes in v2:
- remove unnecessary moving of drm_i915_private from patch 1
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-3-juston.li@intel.com
Update cp_irq_count_cached when reading messages rather than when
writing a message to make sure the value is up to date and not
stale from a previously handled CP_IRQ.
AKE flow doesn't always respond to a read with a ACK write msg.
E.g. AKE_Send_Pairing_Info will "timeout" because we received
a CP_IRQ for reading AKE_Send_H_Prime but no write occurred between that
and reading AKE_Send_Pairing_Info so cp_irq_count_cached is stale
causing the wait to return right away rather than waiting for a new
CP_IRQ.
Signed-off-by: Juston Li <juston.li@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-2-juston.li@intel.com
Driver has to swap the endian before send brightness level value
to tcon.
v2: Use __be16 instead of u16 to fix sparse warning.
v3: Send one or two bytes brightness value depend on the precision.
v4: get data length of brightness value more easily.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-6-shawn.c.lee@intel.com
So far, DCS backlight driver hardcode (0xFF) for max brightness level.
MIPI DCS spec allow max 0xFFFF for set_display_brightness (51h) command.
And VBT brightness precision bits can support 8 ~ 16 bits.
We should set correct precision bits in VBT that meet panel's request.
Driver can refer to this setting then configure max brightness level
in DCS backlight driver properly.
v2: modify variable name brightness_precision_bits instead of
max_brightness_level.
v3: fix checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-5-shawn.c.lee@intel.com
VDSC engine can process only 1 pixel per Cd clock. In case
VDSC is used and max slice count == 1, max supported pixel
clock should be 100% of CD clock. Then do min_cdclk and
pixel clock comparison to get proper min cdclk.
v2:
- Check for dsc enable and slice count ==1 then allow to
double confirm min cdclk value.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-4-shawn.c.lee@intel.com
According to chapter "Sending Commands to the Panel" in bspec #29738
and #49188. If driver try to send DCS long pakcet, we have to program
TX payload register at first. And configure TX header HW register later.
DSC long packet would not be sent properly if we don't follow this
sequence.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-3-shawn.c.lee@intel.com
Driver should wait for free header or payload buffer in FIFO.
It would be good to wait a while for HW to release credit before
give it up to write to HW. Without sending initailize command
sets completely. It would caused MIPI display can't light up properly.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-2-shawn.c.lee@intel.com
Frontbuffer rendering will be dropped for modern platforms but
before that we to prepare DRRS for it.
intel_drrs_flush and intel_drrs_invalidate will not be called
for platforms that will not support frontbuffer rendering so DRRS
needs another way to be notified about to page flips so it can change
between high and low refresh rates as needed.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-3-jose.souza@intel.com
Both functions are pretty much equal, with minor changes that can be
handled by a single parameter.
v3:
- not scheduling work from invalidate operations
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-2-jose.souza@intel.com
It started as a code style fix for the lines above 100 col but it
turned out to simplifications to intel_drrs_set_state().
Now it receives the desired refresh rate type, high or low.
v3:
- Fixed the mode refesh rate debug message
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-1-jose.souza@intel.com
Avoid extra caching of the data. This is slightly more subtle than one
would think. For one thing, we explicitly ignore 0 value in child device
ddc pin; this is specified as N/A and does not warrant a warning. For
another, we start looking for ddc pin collisions in sanitize using
unmapped pin numbering.
v2: Check !devdata in intel_bios_alternate_ddc_pin()
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e1dbf7cbdd2191439e760ab9098242dcec5fbb2e.1630512523.git.jani.nikula@intel.com
Added HBR3 support for ADL_P and ADL_S platform.
Bspec: 53597, 53720, 49185, 55409
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-6-animesh.manna@intel.com
Combo phy is limited to 5.4 GHz on low-voltage SKUs, but both eDP and DP
can do 8.1 GHz on combo phy.
Bspec: 49182, 49205, 49202
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-5-animesh.manna@intel.com
Only higher voltage sku can support HBR3 so a condition
check added in max source rate calculation for ehl/jsl.
Bspec: 32247, 20598
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-4-animesh.manna@intel.com
Combo phy is limited to 5.4 GHz on low-voltage SKUs. Combo phy DP is
limited to 5.4 GHz, while combo phy eDP can do 8.1 GHz.
Bspec: 20584, 20598, 49180, 49201
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-3-animesh.manna@intel.com
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before intel_encoder->type is set. This causes incorrect max source
rate to be used for display 11+. On EHL and JSL, HBR3 is used instead of
HBR2, and on the other affected platforms, HBR2 is used instead of HBR3.
Move intel_dp_set_source_rates() to after intel_encoder->type is
set. Add comment to intel_dp_is_edp() describing unsafe usages. Cleanup
intel_dp_init_connector() while at it.
Note: The same change was originally added as commit 680c45c767
("drm/i915/dp: Correctly advertise HBR3 for GEN11+"), but later reverted
due to issues in CI in commit d391301960 ("Revert "drm/i915/dp:
Correctly advertise HBR3 for GEN11+"").
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-2-animesh.manna@intel.com
Accidentally dropped the else in a rebase fail, causing the DG2 max rate
to be overwritten later in the if ladder.
Fixes: e752d1f9c1 ("drm/i915/dg2: add DG2 UHBR source rates")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901112815.16498-1-jani.nikula@intel.com
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t
-----BEGIN PGP SIGNATURE-----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=vZkA
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Highlights:
- i915 has seen a lot of refactoring and uAPI cleanups due to a
change in the upstream direction going forward
This has all been audited with known userspace, but there may be
some pitfalls that were missed.
- i915 now uses common TTM to enable discrete memory on DG1/2 GPUs
- i915 enables Jasper and Elkhart Lake by default and has preliminary
XeHP/DG2 support
- amdgpu adds support for Cyan Skillfish
- lots of implicit fencing rules documented and fixed up in drivers
- msm now uses the core scheduler
- the irq midlayer has been removed for non-legacy drivers
- the sysfb code now works on more than x86.
Otherwise the usual smattering of stuff everywhere, panels, bridges,
refactorings.
Detailed summary:
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t"
* tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm: (1318 commits)
drm/amd/display: Move AllowDRAMSelfRefreshOrDRAMClockChangeInVblank to bounding box
drm/amd/display: Remove duplicate dml init
drm/amd/display: Update bounding box states (v2)
drm/amd/display: Update number of DCN3 clock states
drm/amdgpu: disable GFX CGCG in aldebaran
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amdgpu: Add support for RAS XGMI err query
drm/amdkfd: Account for SH/SE count when setting up cu masks.
drm/amdgpu: rename amdgpu_bo_get_preferred_pin_domain
drm/amdgpu: drop redundant cancel_delayed_work_sync call
drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend
drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend
drm/amdkfd: map SVM range with correct access permission
drm/amdkfd: check access permisson to restore retry fault
drm/amdgpu: Update RAS XGMI Error Query
drm/amdgpu: Add driver infrastructure for MCA RAS
drm/amd/display: Add Logging for HDMI color depth information
drm/amd/amdgpu: consolidate PSP TA init shared buf functions
drm/amd/amdgpu: add name field back to ras_common_if
drm/amdgpu: Fix build with missing pm_suspend_target_state module export
...
Enable MIPI DSI support on ADL-P platform.
The esc clock changes, WA changes are taken care
in the previous patches.
As per the Bspec the seq remains to be same as TGL.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-3-vandita.kulkarni@intel.com
Wa_16012360555 SW will have to program the "LP to HS Wakeup Guardband"
field to account for the repeaters on the HS Request/Ready PPI signaling
between the Display engine and the DPHY.
v2: Fix build issue.
v3: Align to new naming (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-2-vandita.kulkarni@intel.com
We had a mix of intel_edp_drrs_*(), intel_dp_drrs_*() and
intel_dp_set_drrs_state(), so properly renaming all functions to
keep the same pattern.
While at it, also dropping intel_dp_set_drrs_state from the
documentation as it is a static function.
v3:
- dropping documentation style comment in static function
(intel_drrs_set_state)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-3-jose.souza@intel.com
intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce
some lines from it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com
At this point is sure that HSW and BDW will never have PSR enabled by
default, so here dropping it from device info and cleaning up code.
v2:
- enable psr support for display 9
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-1-jose.souza@intel.com
UHBR modes has higher link rate and added new values for programming
mpll of SNPS phy. No change in sequence, only the pll parameters
are different for UHBR modes.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827103843.527-1-jani.nikula@intel.com
Apparently the last reader of i915->active_pipes was removed with commit
ef79d62b5c ("drm/i915: Encapsulate dbuf state handling harder"), and
now it's only ever written to. Remove it completely.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826141830.889-1-jani.nikula@intel.com
