Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.
So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.
intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.
v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder
v4:
- using the HOBL vswing table until training fails completely (Ville)
v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement
v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active
BSpec: 49291
BSpec: 49399
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The value we program to DDI_BUF_CTL changes at the following places:
- At enabling/disabling the output to configure the port width etc, and
to enable/disable the DDI BUF function.
- At the beginning/end of link re-training to disable/re-enable the DDI
BUF function.
- On HSW/BDW/SKL to change the voltage swing/pre-emph levels.
Except of the above the value we program to the DDI_BUF_CTL register
(intel_dp->DP) doesn't change, so no need to reprogram the register when
changing the link training patterns (which is programmed via the
DP_TP_CTL register on DDI platforms).
v2:
- Fix the commit message wrt. voltage/pre-emph level values in
intel_dp->DP. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
According to BSpec this flag should not be changed while the DDI
function is enabled. On BDW+ the DP_TP_CTL register spec also states it
explicitly that the HW takes care of enabling/disabling the scrambling
for training patterns (and it must stay enabled for normal pixel
output). Assume that this HW automatic handling of scrambling is also
true for HSW.
BSpec: 8013, 7557, 50484
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Explicitly check for i830 when assigning the .get_cdclk() vfunc,
and then deal with the case of not having assigned the vfunc
separately. Less confusing, and gets rid of the checkpatch complaint
about using {} on one branch but not the others.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There's a pointless hole in struct intel_cdclk_vals, get rid of it.
Fortunately we already use named initializers so the order does not
matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Since g4x the CFB base only takes a 28bit offset into stolen.
Not sure if the CFB is allowed to start below that limit but
then extend beyond it. Let's assume not and just restrict the
allocation to the first 256MiB (in the unlikely case
we have more stolen than that).
v2: s/BIT/BIT_ULL/ (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714201945.18959-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some types
of hardware can generate the full range of signals that they're capable
of. The remainder is mostly minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=v6MG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Since DP-specific information is stored in driver's structures, every
driver needs to implement subconnector property by itself.
v2: updates to match previous commit changes
v3: rebase
v4: renamed a function call
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Jeevan B <jeevan.b@intel.com>
Signed-off-by: Oleg Vasilev <oleg.vasilev@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #and acked for merging
Tested-by: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1587732655-17544-2-git-send-email-jeevan.b@intel.com
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larget cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
-
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages
-----BEGIN PGP SIGNATURE-----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=Yvtd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"New xilinx displayport driver, AMD support for two new GPUs (more
header files), i915 initial support for RocketLake and some work on
their DG1 (discrete chip).
The core also grew some lockdep annotations to try and constrain what
drivers do with dma-fences, and added some documentation on why the
idea of indefinite fences doesn't work.
The long list is below.
I do have some fixes trees outstanding, but I'll follow up with those
later.
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larger cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages"
* tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm: (1747 commits)
drm/msm: use kthread_create_worker instead of kthread_run
drm/msm/mdp5: Add MDP5 configuration for SDM636/660
drm/msm/dsi: Add DSI configuration for SDM660
drm/msm/mdp5: Add MDP5 configuration for SDM630
drm/msm/dsi: Add phy configuration for SDM630/636/660
drm/msm/a6xx: add A640/A650 hwcg
drm/msm/a6xx: hwcg tables in gpulist
drm/msm/dpu: add SM8250 to hw catalog
drm/msm/dpu: add SM8150 to hw catalog
drm/msm/dpu: intf timing path for displayport
drm/msm/dpu: set missing flush bits for INTF_2 and INTF_3
drm/msm/dpu: don't use INTF_INPUT_CTRL feature on sdm845
drm/msm/dpu: move some sspp caps to dpu_caps
drm/msm/dpu: update UBWC config for sm8150 and sm8250
drm/msm/dpu: use right setup_blend_config for sm8150 and sm8250
drm/msm/a6xx: set ubwc config for A640 and A650
drm/msm/adreno: un-open-code some packets
drm/msm: sync generated headers
drm/msm/a6xx: add build_bw_table for A640/A650
drm/msm/a6xx: fix crashstate capture for A650
...
drm/i915 features for v5.9, batch #2
Highlights:
- Very early DG1 enabling (Abdiel, Lucas, Anusha)
Gem/GT:
- Fix spinlock recursion on signaling a signaled request (Chris)
- Perf: Use GTT when saving/restoring engine GPR (Umesh Nerlige Ramappa)
- SSEU refactoring, debugfs move under gt/ (Daniele, Venkata Sandeep Dhanalakota)
- Various GT refactoring and cleanup, preparation for future changes (Daniele)
- Adjust HuC state accordingly after GuC fetch error (Michał Winiarski)
- UC debugfs updates (Michał Winiarski)
- Only revoke the GGTT mmappings on aperture detiling changes (Chris)
- Only revoke mmap handlers if active (Chris)
- Split the context's obj:vma lut into its own mutex (Chris)
- Various memory, mmap and performance optimisations (Chris)
- Improve system stability in case of false CS events (Chris)
- Various refactorings and cleanup (Chris)
- Always reset the engine on execlist failures (Chris)
- Trace placement of timeline HWSP (Chris)
- Update dma-attributes for our sg DMA (Chris)
Display:
- TGL CDCLK workaround tweaks to unbreak 8K display support (Stanislav)
- A number of FBC fixes, along with i865 FBC enabling (Ville)
- Validate MST modes against PBN limits (Lyude, Shawn Lee)
- Do not access non-existing swizzle registers (Lucas)
- Revert GEN11+ HBR3 rate fix that caused issues on TGL (Matt Atwood)
- Update TGL+ combo phy initialization to match spec update (José)
- Fix HDCP Content Protection property state machine (Anshuman)
- Fix HDCP revoked keys handling (Ram)
- Improve DDI BUF status checks and waits (Manasi)
- Various SDVO+HDMI+DVI fixes around colorimetry, clocking, pixel repeat etc. (Ville)
- DP voltage swing function refactoring (José)
- WARN if max vswing/pre-emphasis violates the DP spec (Ville)
Other:
- Add new EHL PCI IDs (José)
- Unify struct intel_digital_port variable naming (Lucas)
- Various taint updates to aid debugging and improve CI (Michał Winiarski)
- Straggler conversions to new mmio register accessors (Daniele)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87a70029vz.fsf@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge v5.8-rc6 into drm-next
I've got a silent conflict + two trees based on fixes to merge.
Fixes a silent merge with amdgpu
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
Cross-subsystem Changes:
- Add ckoenig as dma-buf maintainer.
- Revert invalid fix for dma-fence-chain, and fix selftest.
- Add fixmes to amifb about APUS support.
- Use array3_size in fbcon_prepare_logo, and struct_size() in alloc_apertures.
- Fix leaks in neofb, fb/savage and omapfb.
- Other small fixes to fb code.
- Convert some dt bindings to schema for some panels, and fix simple-framebuffer dt example.
Core Changes:
- Add DRM_FORMAT_MOD_GENERIC_16_16_TILE as alias to DRM_FORMAT_MOD_SAMSUNG_16_16_TILE,
as it can be used more generic.
- Add support for multiple DispID extension blocks in edid.
- Use https instead of http for some of the urls.
- Use drm_* macros for logging in mipi-dsi and fb-helper.
- Further cleanup ttm_mem_reg handling.
- Remove duplicated words in comments.
Driver Changes:
- Use __drm_atomic_helper_crtc_reset in all atomic drivers.
- Add Amlogic Video FBC support to meson and fourcc to core.
- Refactor hisilicon's hibmc_drv_vdac.
- Create a TXP CRTC for vc4.
- Rework cursor support in ast.
- Fix runtime PM in STM.
- Allow bigger cursors in vkms.
- Cleanup sg handling in radeon and amdgpu, and stop creating dummy
gtt nodes with ttm fixed.
- Rework crtc handling in mgag200.
- Miscellaneous small fixes to meson, vgem, bridge/dw-hdmi,
panel/auo,b116xw03, panel/LG LB070WV8, lima, bridge/sil_sii8620,
virtio, tilcdc.
-----BEGIN PGP SIGNATURE-----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=XKYB
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
Cross-subsystem Changes:
- Add ckoenig as dma-buf maintainer.
- Revert invalid fix for dma-fence-chain, and fix selftest.
- Add fixmes to amifb about APUS support.
- Use array3_size in fbcon_prepare_logo, and struct_size() in alloc_apertures.
- Fix leaks in neofb, fb/savage and omapfb.
- Other small fixes to fb code.
- Convert some dt bindings to schema for some panels, and fix simple-framebuffer dt example.
Core Changes:
- Add DRM_FORMAT_MOD_GENERIC_16_16_TILE as alias to DRM_FORMAT_MOD_SAMSUNG_16_16_TILE,
as it can be used more generic.
- Add support for multiple DispID extension blocks in edid.
- Use https instead of http for some of the urls.
- Use drm_* macros for logging in mipi-dsi and fb-helper.
- Further cleanup ttm_mem_reg handling.
- Remove duplicated words in comments.
Driver Changes:
- Use __drm_atomic_helper_crtc_reset in all atomic drivers.
- Add Amlogic Video FBC support to meson and fourcc to core.
- Refactor hisilicon's hibmc_drv_vdac.
- Create a TXP CRTC for vc4.
- Rework cursor support in ast.
- Fix runtime PM in STM.
- Allow bigger cursors in vkms.
- Cleanup sg handling in radeon and amdgpu, and stop creating dummy
gtt nodes with ttm fixed.
- Rework crtc handling in mgag200.
- Miscellaneous small fixes to meson, vgem, bridge/dw-hdmi,
panel/auo,b116xw03, panel/LG LB070WV8, lima, bridge/sil_sii8620,
virtio, tilcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8b360d65-f228-9286-d247-3004156a5254@linux.intel.com
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Currently we're failing to recalculate the gen9 FBC w/a stride
unless something more drastic than just the modifier itself has
changed. This often leaves us with FBC enabled with the linear
fbdev framebuffer without the w/a stride enabled. That will cause
an immediate underrun and FBC will get promptly disabled.
Fix the problem by checking if the w/a stride is about to change,
and go through the full dance if so. This part of the FBC code
is still pretty much a disaster and will need lots more work.
But this should at least fix the immediate issue.
v2: Deactivate FBC when the modifier changes since that will
likely require resetting the w/a CFB stride
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200711080336.13423-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 0428ab013f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we're failing to recalculate the gen9 FBC w/a stride
unless something more drastic than just the modifier itself has
changed. This often leaves us with FBC enabled with the linear
fbdev framebuffer without the w/a stride enabled. That will cause
an immediate underrun and FBC will get promptly disabled.
Fix the problem by checking if the w/a stride is about to change,
and go through the full dance if so. This part of the FBC code
is still pretty much a disaster and will need lots more work.
But this should at least fix the immediate issue.
v2: Deactivate FBC when the modifier changes since that will
likely require resetting the w/a CFB stride
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200711080336.13423-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
According to the DP spec a DPTX must support vswing/pre-emphasis
up to and including level 2. Level 3 is optional (actually DP 1.4a
seems to make even level 3 mandatory for HBR2/3, while leaving it
optional for RBR/HBR1).
WARN if out encoders' .voltage_max()/.preemph_max() return
an illegal value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200709145845.18118-1-ville.syrjala@linux.intel.com
So far, max dot clock rate for MST mode rely on physcial
bandwidth limitation. It would caused compatibility issue
if source display resolution exceed MST hub output ability.
For example, source DUT had DP 1.2 output capability.
And MST docking just support HDMI 1.4 spec. When a HDMI 2.0
monitor connected. Source would retrieve EDID from external
and get max resolution 4k@60fps. DP 1.2 can support 4K@60fps
because it did not surpass DP physical bandwidth limitation.
Do modeset to 4k@60fps, source output display data but MST
docking can't output HDMI properly due to this resolution
already over HDMI 1.4 spec.
Refer to commit <fcf463807596> ("drm/dp_mst: Use full_pbn
instead of available_pbn for bandwidth checks").
Source driver should refer to full_pbn to evaluate sink
output capability. And filter out the resolution surpass
sink output limitation.
Changes since v1:
* Using mgr->base.lock to protect full_pbn.
Changes since v2:
* Add ctx lock.
Changes since v3:
* s/intel_dp_mst_mode_clock_exceed_pbn_bandwidth/
intel_dp_mst_mode_clock_exceeds_pbn_bw/
* Use the new drm_connector_helper_funcs.mode_valid_ctx to properly pipe
down the drm_modeset_acquire_ctx that the probe helpers are using, so
we can safely grab &mgr->base.lock without deadlocking
Changes since v4:
* Move drm_dp_calc_pbn_mode(mode->clock, bpp, false) > port->full_pbn
check
* Fix the bpp we use in drm_dp_calc_pbn_mode()
* Drop leftover (!mgr) check
* Don't check for if full_pbn is unset. To be clear - it _can_ be unset,
but if it is then it's certainly a bug in DRM or a non-compliant sink
as full_pbn should always be populated by the time we call
->mode_valid_ctx.
We should workaround non-compliant sinks with full_pbn=0, but that
should happen in the DP MST helpers so we can estimate the full_pbn
value as best we can.
Tested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Co-developed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200713170746.254388-3-lyude@redhat.com
HOBL means hours of battery life, it is a power-saving feature
were supported motherboards can use a special voltage swing table
that uses less power.
So here parsing the VBT to check if this feature is supported.
BSpec: 20150
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708205512.21625-3-jose.souza@intel.com
Some platforms apply the FBC w/as in .init_clock_gating(), some
in fbc_activate(). Move them all to .init_clock_gating() for
consistentce. Also safer since we don't have to worry about the
RMWs clashing with any other runtime use of the same registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708131223.9519-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
.get_modes() is supposed to return the number of modes added to the
probed_modes list (not that anyone actually checks for anything
except zero vs. not zero). Let's do that. Also switch over to using
intel_connector_update_modes() instead of hand rolling it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-8-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
With SDVO the pipe config pixel_multiplier only concerns itself with the
data on the SDVO bus. Any HDMI specific pixel repeat must be handled by
the SDVO device itself. To do that simply configure the SDVO pixel
replication factor appropriately. We already set up the infoframe PRB
values correctly via the infoframe helpers.
There is no cap we can check for this. The spec says that 1X,2X,4X are
mandatory, anything else is optional. 1X and 2X are all we need so
we should be able to assume they work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The code assumes that DRM_MODE_FLAG_DBLCLK means that we enable the
pixel repeat feature. That only works with HDMI since it requires
AVI infoframe to signal the information to the sink. Hence even if
the mode dotclock would be valid we cannot currently assume that
we can just ignore the DBLCLK flag. Reject it for DVI sinks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-6-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SDVO/HDMI port register limited color range bit can only be used
with TMDS encoding and not SDVO encoding, ie. to be used only when
using the port as a HDMI port as opposed to a SDVO port. The SDVO
spec does have a note that some GMCHs might allow that, but gen4
bspec vehemently disagrees. I suppose on ILK+ it might work since
the color range handling is on the CPU side rather than on the PCH
side, so there is no clear linkage between the TMDS vs. SDVO
encoding and color range. Alas, I have no hardware to test that
theory.
To implement limited color range support for SDVO->HDMI we need to
ask the SDVO device to do the range compression. Do so, but first
check if the device even supports the colorimetry selection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Based on the platform, Bspec expects us to wait or poll with
timeout for DDI BUF IDLE bit to be set to 0 (non idle) or get active
after enabling DDI_BUF_CTL.
v2:
* Based on platform, fixed delay or poll (Ville)
* Use a helper to do this (Imre, Ville)
v3:
* Add a new function _active for DDI BUF CTL to be non idle (Ville)
v4:
* Use the timeout for GLK (Ville)
v5:
* Add bspec quote, change timeout to 500us (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-2-manasi.d.navare@intel.com
Modify the helper to add a fixed delay or poll with timeout
based on platform specification to check for either Idle bit
set (DDI_BUF_CTL is idle for disable case)
v2:
* Use 2 separate functions or idle and active (Ville)
v3:
* Change the timeout to 16usecs (Ville)
v4:
* Change the timeout 8, follow spec (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-1-manasi.d.navare@intel.com
drm_hdcp_check_ksvs_revoked() returns the number of revoked keys and
error codes when the SRM parsing is failed.
Errors in SRM parsing can't affect the HDCP auth, hence with this patch,
I915 will look out for revoked key count alone.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429134555.22106-1-ramalingam.c@intel.com
Content Protection property should be updated as per the kernel
internal state. Let's say if Content protection is disabled
by userspace, CP property should be set to UNDESIRED so that
reauthentication will not happen until userspace request it again,
but when kernel disables the HDCP due to any DDI disabling sequences
like modeset/DPMS operation, kernel should set the property to
DESIRED, so that when opportunity arises, kernel will start the
HDCP authentication on its own.
Somewhere in the line, state machine to set content protection to
DESIRED from kernel was broken and IGT coverage was missing for it.
This patch fixes it.
v2:
- Fixing hdcp CP state in connector atomic check function
intel_hdcp_atomic_check(). [Maarten]
This will require to check hdcp->value in intel_hdcp_update_pipe()
in order to avoid enabling hdcp, if it was already enabled.
v3:
- Rebased.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/350962/?series=72664&rev=2 #v1
Link: https://patchwork.freedesktop.org/patch/359396/?series=72251&rev=3 #v2
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630082048.22308-1-anshuman.gupta@intel.com
This is new step that was recently added to the combo phy
initialization.
v2:
- using intel_de_rmw()
v3:
- going back to read() modify and write() as group register can't be
read
BSpec: 49291
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625195252.39312-1-jose.souza@intel.com
The current fence_y_offset calculation is broken. I think it more or
less used to do the right thing, but then I changed the plane code
to put the final x/y source offsets back into the src rectangle so
now it's just subtraacting the same value from itself. The code would
never have worked if we allowed the framebuffer to have a non-zero
offset.
Let's do this in a better way by just calculating the fence_y_offset
from the final plane surface offset. Note that we don't align the
plane surface address to fence rows so with horizontal panning there's
often a horizontal offset from the fence start to the surface address
as well. We have no way to tell the hardware about that so we just
ignore it. Based on some quick tests the invlidation still happens
correctly. I presume due to the invalidation nuking at least the full
line (or a segment of multiple lines).
Fixes: 54d4d719fa ("drm/i915: Overcome display engine stride limits via GTT remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-4-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 5331889b5f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The initial CI results did not include a TGL system which includes a
panel that is having issues with patch. Revert while we triage.
This reverts commit 680c45c767.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702230957.30536-1-matthew.s.atwood@intel.com
Unlike all the other pre-snb desktop platforms i865 actually
supports FBC. Let's enable it.
Quote from the spec:
"DevSDG provides the same Run-Length Encoded Frame Buffer
Compression (RLEFBC) function as exists in DevMGM."
As i865 only has the one pipe we want to skip massaging the
plane<->pipe assignment aimed at getting FBC+LVDS working on
the mobile platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The MSG_FBC_REND_STATE register only exists on snb+. For older
platforms (would also work for snb+) we can simply rewite DSPSURF
to trigger a flip nuke.
While generally RMW is considered harmful we'll use it here for
simplicity. And since FBC doesn't exist in i830 we don't have to
worry about the DSPSURF double buffering hardware fails present
on that platform.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Consult the actual plane stride instead of the fb stride. The two
will disagree when we remap the gtt. The plane stride is what the
hw will be fed so that's what we should look at for the FBC
retrictions/cfb allocation.
Since we no longer require a fence we are going to attempt using
FBC with remapping, and so we should look at correct stride.
With 90/270 degree rotation the plane stride is stored in units
of pixels, so we need to conver it to bytes for the purposes
of calculating the cfb stride. Not entirely sure if this matches
the hw behaviour though. Need to reverse engineer that at some
point...
We also need to reorder the pixel format check vs. stride check
to avoid triggering a spurious WARN(stride & 63) with cpp==1 and
plane stride==32.
v2: Try to deal with rotated stride and related WARN
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 691f7ba58d ("drm/i915/display/fbc: Make fences a nice-to-have for GEN9+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702153723.24327-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We still need "Bump up CDCLK" workaround otherwise getting
underruns - however currently it blocks 8K as CDCLK = Pixel rate,
in 8K case would require CDCLK to be around 1 Ghz which is not
possible.
v2: - Convert to expression(max(min_cdclk, min(pixel_rate, max_cdclk))
(Ville Syrjälä)
- Use type specific min_t, max_t(Ville Syrjälä)
Fixes: 46d53e271c ("Revert "drm/i915: Remove unneeded hack now for CDCLK"")
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702091526.10096-1-stanislav.lisovskiy@intel.com
We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around
5 intel_dport
36 dport
479 intel_dig_port
352 dig_port
Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.
v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
The old epoch counter was left uninited, so the function returned a
changed state always.
While at it debug print the old epoch counter as well.
Fixes: 35205ee9ba ("drm/i915: Send hotplug event if edid had changed")
Cc: Kunal Joshi <kunal1.joshi@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701180001.15857-1-imre.deak@intel.com
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before encoder_type is set. This caused GEN11+ to incorrectly strip
HBR3 from source rates for edp. Move intel_dp_set_source_rates() to
after encoder_type is set. Add comment to intel_dp_is_edp() describing
unsafe usages.
v2: Alter intel_dp_set_source_rates final position (Ville/Manasi).
Remove outdated comment (Ville).
Slight optimization of control flow in intel_dp_init_connector.
Slight rewording in commit message.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630233310.10191-1-matthew.s.atwood@intel.com
To simplify things, call the combo PHY/TBT PLL calculation functions
directly from the corresponding combo/TypeC PLL get functions, instead of
calling the same calculation functions after having to recheck if the
given PHY is combo or TypeC.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629185848.20550-2-imre.deak@intel.com
When the reference clock is 38.4MHz, using the current TBT PLL
fractional divider value results in a slightly off TBT link frequency.
This causes an endless loop of link training success followed by a bad
link signaling and retraining at least on a Dell WD19TB TBT dock. The
workaround provided by the HW team is to divide the fractional divider
value by two. This fixed the link training problem on the ThinkPad dock.
The same workaround is needed on some EHL platforms and for combo PHY
PLLs, these will be addressed in a follow-up.
Bspec: 49204
References: HSDES#22010772725
References: HSDES#14011861142
Reported-and-tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629185848.20550-1-imre.deak@intel.com
Future patches will bring PSR2 selective fetch configuration
validation but most of the configuration checks will be used for HW
tracking and selective fetch so the reoder was necessary.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626010151.221388-2-jose.souza@intel.com
Often we seem to detect an underrun right after modeset on gen2.
It seems to be a spurious detection (potentially the pipe is still
in a wonky state when we enable the planes). An extra vblank wait
seems to cure it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The default fbc1 compression interval we use is 500 frames. That
translates to over 8 seconds typically. That's rather excessive
so let's drop it to 1 second.
The hardware will not attempt recompression unless at least one
line has been modified, so a shorter compression interval should
not cause extra bandwidth use in the purely idle scenario. Of
course in the mostly idle case we are possibly going to recompress
a bit more.
Should really try to find some kind of sweet spot to minimize
the energy usage...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The hardware host tracking won't nuke the entire cfb (unless the
entire fb is written through the gtt) so don't clear the busy_bits
for gtt tracking.
Not that it really matters anymore since we've lost ORIGIN_GTT usage
everywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-7-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The current fence_y_offset calculation is broken. I think it more or
less used to do the right thing, but then I changed the plane code
to put the final x/y source offsets back into the src rectangle so
now it's just subtraacting the same value from itself. The code would
never have worked if we allowed the framebuffer to have a non-zero
offset.
Let's do this in a better way by just calculating the fence_y_offset
from the final plane surface offset. Note that we don't align the
plane surface address to fence rows so with horizontal panning there's
often a horizontal offset from the fence start to the surface address
as well. We have no way to tell the hardware about that so we just
ignore it. Based on some quick tests the invlidation still happens
correctly. I presume due to the invalidation nuking at least the full
line (or a segment of multiple lines).
Fixes: 54d4d719fa ("drm/i915: Overcome display engine stride limits via GTT remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-4-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Added epoch counter checking to intel_encoder_hotplug
in order to be able process all the connector changes,
besides connection status. Also now any change in connector
would result in epoch counter change, so no multiple checks
are needed.
v2: Renamed change counter to epoch counter. Fixed type name.
v3: Fixed rebase conflict
v4: Remove duplicate drm_edid_equal checks from hdmi and dp,
lets use only once edid property is getting updated and
increment epoch counter from there.
Also lets now call drm_connector_update_edid_property
right after we get edid always to make sure there is a
unified way to handle edid change, without having to
change tons of source code as currently
drm_connector_update_edid_property is called only in
certain cases like reprobing and not right after edid is
actually updated.
v5: Fixed const modifiers, removed blank line
v6: Removed drm specific part from this patch, leaving only
i915 specific changes here.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630002700.5451-4-kunal1.joshi@intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Currently there is no null check for a failed memory allocation
on the dsb object and without this a null pointer dereference
error can occur. Fix this by adding a null check.
Note: added a drm_err message in keeping with the error message style
in the function.
Addresses-Coverity: ("Dereference null return")
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616114221.73971-1-colin.king@canonical.com
A single Ri mismatch doesn't automatically mean that the link integrity
is broken. Update and check of Ri and Ri' are done asynchronously. In
case an update happens just between the read of Ri' and the check against
Ri there will be a mismatch even if the link integrity is fine otherwise.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504123524.7731-1-oliver.barta@aptiv.com
The linetime watermark is a 9 bit value, which gives us
a maximum linetime of just below 64 usec. If the linetime
exceeds that value we currently just discard the high bits
and program the rest into the register, which angers the
state checker.
To avoid that let's just clamp the value to the max. I believe
it should be perfectly fine to program a smaller linetime wm
than strictly required, just means the hardware may fetch data
sooner than strictly needed. We are further reassured by the
fact that with DRRS the spec tells us to program the smaller
of the two linetimes corresponding to the two refresh rates.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625200003.12436-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The DP spec says:
"The transmitter shall support at least three levels of voltage
swing (Levels 0, 1, and 2).
If only three levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 10 (Level 2)),
this bit shall be set to 1, and cleared in all other cases.
If all four levels of voltage swing are supported (VOLTAGE
SWING SET field (bits 1:0) are programmed to 11 (Level 3)),
this bit shall be set to 1,and cleared in all other cases."
Let's follow that exactly instead of the current apporach
where we can set those also for vswing/preemph levels 0 or 1
(or 2 when the platform max is 3).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Catch up with upstream, in particular to get c1e8d7c6a7 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
During encoder enabling we clear the flag before starting the ACT
sequence and wait for the flag, but the clearing is missing during
encoder disabling, add it there too. Since nothing cleared the flag
automatically we could've run subsequent disabling steps too early.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-5-imre.deak@intel.com
It's not clear if the DP_TP_STATUS flags other than the ACT sent flag
have some side-effect, so don't clear those; we don't depend on the
state of these flags anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-4-imre.deak@intel.com
During transcoder enabling we'll configure the transcoder in MST mode
and enable the VC payload allocation, which will start the ACT sequence.
Before waiting for the ACT sequence completion, we need to clear the ACT
sent flag, but based on the above we can do this right before enabling
the transcoder.
For clarity, move the flag clearing closer to where we wait for it.
While at it also factor out some common code.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-3-imre.deak@intel.com
During the initial probing of an MST sink, MST core will determine the
sink's link bandwidth based on its own version of the sink link
rate/lane count caps it reads from the DPCD. At a later point (after
probing and 1 or more modesets) i915 may limit the link parameters wrt.
the original source/sink common caps above due to link training failures
during a modeset and the resulting link training fallback logic.
Based on the above a modeset following another modeset with a link
training error will compute the i915 HW specific and DP protocol timing
parameters (data/link M/N and MST TU values) taking into account only
the unlimited source/sink common caps, but not taking into account the
fallback limits. This will also let DRM core oversubscribe the actual
link bandwidth during the MST payload allocation.
Prevent the above problem by disabling the link training fallback on MST
links for now, until the MST probe time initialization and the MST
compute config logic can deal with changing link parameters.
The misconfigured timings lead at least to a
'Timed out waiting for DP idle patterns'
error.
v2: (Ville)
- Print link training error message on the MST path too.
- Clarify the problem in the commit log.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-2-imre.deak@intel.com
MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.
One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a
'Timed out waiting for ACT sent when disabling'
error, due to reading from the incorrect DP_TP_STATUS register.
This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.
v2:
- Correct the failure scenario in the commit log. (José)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com
Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.
The stragglers are:
* i915.force_probe and i915.modeset. Needed before dev_priv is
available. This is fine because the parameters are read-only and never
modified.
* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
I915_STATE_WARN_ON would result in massive and ugly churn. This is
handled by not exposing the parameter via debugfs, and leaving the
parameter writable in sysfs. This may be fixed up in follow-up work.
* i915.inject_probe_failure. Only makes sense in terms of the module,
not the device. This is handled by not exposing the parameter via
debugfs.
v2: Fix uc i915 lookup code (Michał Winiarski)
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com
Since the PWM framework is switching struct pwm_state.duty_cycle's
datatype to u64, prepare for this transition by using DIV_ROUND_UP_ULL
to handle a 64-bit dividend.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For all ddi, encoder->type holds output type as ddi,
assigning it to individual o/p types is no more valid.
Fixes: 362bfb995b ("drm/i915/tgl: Add DKL PHY vswing table for HDMI")
v2: Rebase, no functional change.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612082237.11886-1-vandita.kulkarni@intel.com
(cherry picked from commit 94641eb6c6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:
[ 870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[ 871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[ 871.019212] mce: [Hardware Error]: TSC 135a261fe61
[ 871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[ 871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 871.019212] Kernel panic - not syncing: Fatal machine check
[ 871.019212] Kernel Offset: disabled
Bspec: 4287
Fixes: fa37a21327 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com
(cherry picked from commit c980216dd2)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
For all ddi, encoder->type holds output type as ddi,
assigning it to individual o/p types is no more valid.
Fixes: 362bfb995b ("drm/i915/tgl: Add DKL PHY vswing table for HDMI")
v2: Rebase, no functional change.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612082237.11886-1-vandita.kulkarni@intel.com
Some TypeC -> native DP adapters, at least the Club 3D CAC-1557 adapter,
incorrectly filter out HPD short pulses with a duration less than
~540 usec, leading to MST probe failures.
According to the DP Standard 2.0 section 5.1.4:
- DP sinks should generate short pulses in the 500 usec -> 1 msec range
- DP sources should detect short pulses in the 250 usec -> 2 msec range
According to the DP Alt Mode on TypeC Standard section 3.9.2, adapters
should detect and forward short pulses according to how sources should
detect them as specified in the DP Standard (250 usec -> 2 msec).
Based on the above filtering out short pulses with a duration less than
540 usec is incorrect.
To make such adapters work add support for a driver polling on MST
inerrupt flags, and wire this up in the i915 driver. The sink can clear
an interrupt it raised after 110 msec if the source doesn't respond, so
use a 50 msec poll period to avoid missing an interrupt. Polling of the
MST interrupt flags is explicitly allowed by the DP Standard.
This fixes MST probe failures I saw using this adapter and a DELL U2515H
monitor.
v2:
- Fix the wait event timeout for the no-poll case.
v3 (Ville):
- Fix the short pulse duration limits in the commit log prescribed by the
DP Standard.
- Add code comment explaining why/how polling is used.
- Factor out a helper to schedule the port's hpd irq handler and move it
to the rest of hotplug handlers.
- Document the new MST callback.
- s/update_hpd_irq_state/poll_hpd_irq/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200604184500.23730-2-imre.deak@intel.com
Currently MST on a port can get enabled/disabled from the hotplug work
and get disabled from the short pulse work in a racy way. Fix this by
relying on the MST state checking in the hotplug work and just schedule
a hotplug work from the short pulse handler if some problem happened
during the MST interrupt handling.
This removes the explicit MST disabling in case of an AUX failure, but
if AUX fails, then probably the detection will also fail during the
scheduled hotplug work and it's not guaranteed that we'll see
intermittent errors anyway.
While at it also simplify the error checking of the MST interrupt
handler.
v2:
- Convert intel_dp_check_mst_status() to return bool. (Ville)
- Change the intel_dp->is_mst check to an assert, since after this patch
the condition can't change after we checked it previously.
- Document the return value from intel_dp_check_mst_status().
v3:
- Remove the intel_dp->is_mst check from intel_dp_check_mst_status().
There is no point in checking the same condition twice, even though
there is a chance that the hotplug work running concurrently changes
it.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605094801.17709-1-imre.deak@intel.com
DSC is not supported on DP MST streams so just don't add this entry for
MST connectors.
This also fixes an OOPS, caused by the encoder->digport cast, which is
not valid for MST encoders.
v2:
- Check encoder, which is unset for an MST connector, before it gets
enabled.
v3:
- Just don't add this debugfs file for MST connectors. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609184140.4937-1-imre.deak@intel.com
According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:
[ 870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[ 871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[ 871.019212] mce: [Hardware Error]: TSC 135a261fe61
[ 871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[ 871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 871.019212] Kernel panic - not syncing: Fatal machine check
[ 871.019212] Kernel Offset: disabled
Bspec: 4287
Fixes: fa37a21327 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com
RKL doesn't have DSI outputs, so we shouldn't try to read out the DSI
transcoder registers.
v2(MattR):
- Just set the 'extra panel mask' to edp | dsi0 | dsi1 and then mask
against the platform's cpu_transcoder_mask to filter out the ones
that don't exist on a given platform. (Ville)
v3(MattR):
- Only include DSI transcoders on gen11+ again. (Ville)
- Use for_each_cpu_transcoder_masked() for loop. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-5-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
HPD pin handling for RKL+TGP is a special case; we effectively select
the HPD pin based on the DDI (A,B,D,E) rather than the PHY (A,B,C,D).
This differs from the regular behavior of RKL+CMP (and also TGL+TGP).
v2:
- Rather than providing a custom hpd_pin mapping table, just assign
encoder->hpd_pin in a custom manner for this setup. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-4-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rocket Lake uses the same 'abox0' mechanism to handle pixel data
transfers from memory that gen11 platforms used, rather than the
abox1/abox2 interfaces used by TGL/DG1. For the most part this is a
hardware implementation detail that's transparent to driver software,
but we do have to program a couple of tuning registers (MBUS_ABOX_CTL
and BW_BUDDY registers) according to which ABOX instances are used by a
platform. Let's track the platform's ABOX usage in the device info
structure and use that to determine which instances of these registers
to program.
As an exception to this rule is that even though TGL/DG1 use ABOX1+ABOX2
for data transfers, we're still directed to program the ABOX_CTL
register for ABOX0; so we'll handle that as a special case.
v2:
- Store the mask of platform-specific abox registers in the device
info structure.
- Add a TLB_REQ_TIMER() helper macro. (Aditya)
v3:
- Squash ABOX and BW_BUDDY patches together and use a single mask for
both of them, plus a special-case for programming the ABOX0 instance
on all gen12. (Ville)
Bspec: 50096
Bspec: 49218
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-2-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Avoid a NULL dereference for a mismatched encoder type, hit when
probing state for all encoders.
This is a band aid to prevent the OOPS as the right fix is "probably to
swap the psr vs infoframes.enable checks, or outright disappear from
this function" (Ville).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1892
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200525124912.16019-1-chris@chris-wilson.co.uk
(cherry picked from commit 22da5d846d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This reverts commit 82ea174dc5.
Unfortunately according to our recent findings there is still some
unidentified factor, requiring CDCLK to be set higher - otherwise we
still get underruns on some multipipe configurations, despite CDCLK
being set according to BSpec formula. So getting again back into debug
mode to indentify the cause, meanwhile setting CDCLK=Pixel rate back in
order to remove regression in 10% of the cases due to FIFO underruns.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: cd19154608 ("drm/i915: Adjust CDCLK accordingly to our DBuf bw needs")
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200608065552.21728-1-stanislav.lisovskiy@intel.com
- Includes gvt-next-fixes-2020-05-28
- Use after free fix for display global state.
- Whitelisting context-local timestamp on Gen9
and two scheduler fixes with deps (Cc: stable)
- Removal of write flag from sysfs files where
ineffective
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200604150454.GA59322@jlahtine-desk.ger.corp.intel.com
The IO buffer Wake and Fast Wake bit size and value have been changed from
Gen12+. It programs the default value of IO buffer Wake and Fast Wake on
Gen12+. It adds definitions of IO buffer Wake and Fast Wake for pre Gen12
and Gen12+. And it aligns PSR2 definition macros.
v2: Fix macro definitions. (José)
v3: Addressed review comments from José
- Add missing default values of IO_BUFFER_WAKE and FAST_WAKE for GEN9+
- Change a style of macro naming in order to use lines as input.
- Update Todo comments.
v4: Add parentheses to macros to avoid precedence issues.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200607143614.185246-1-gwan-gyeong.mun@intel.com
We accidentally dropped matching for DVO_PORT_DPE from the VBT mapping
table when we refactored the function. Restore it.
Fixes: 4628142aec ("drm/i915/rkl: provide port/phy mapping for vbt")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606031803.3309624-1-matthew.d.roper@intel.com
This parameter is meant to be used when PSR issues are found as some
issues in the past was due wrong values set in VBT so this would be
a quick and easy way to ask users or for us to check if the issue is
due VBT values.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520212756.354623-1-jose.souza@intel.com
RKL doesn't have PSR2 HW tracking, it was replaced by software/manual
tracking. The driver is required to track the areas that needs update
and program hardware to send selective updates.
So until the software tracking is implemented, PSR2 needs to be disabled
for platforms without PSR2 HW tracking.
BSpec: 50422
BSpec: 50424
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-15-matthew.d.roper@intel.com
RKL uses DDI's A, B, TC1, and TC2 which need to map to combo PHY's A-D.
Bspec: 49181
Cc: Imre Deak <imre.deak@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-6-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
As latest update we have now 2 voltage swing tables for DP over DKL
PHY with only one difference in Level 0 pre-emphasis 3.
So with 2 tables for DP is time to have one single function to return
all DKL voltage swing tables.
BSpec: 49292
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com
Previous patch didn't take into account all pipes
but only those in state, which could cause wrong
CDCLK conclcusions and calculations.
Also there was a severe issue with min_cdclk being
assigned to 0 every compare cycle.
Too bad this was found by me only after merge.
This could be also causing the issues in test, however
not clear - anyway marking this as fixing the
"Adjust CDCLK accordingly to our DBuf bw needs".
v2: - s/pipe/crtc->pipe/
- save a bit of instructions by
skipping inactive pipes, without
getting 0 DBuf slice mask for it.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: cd19154608 ("drm/i915: Adjust CDCLK accordingly to our DBuf bw needs")
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200601173058.5084-1-stanislav.lisovskiy@intel.com
Certain combo PHYs act as a compensation master to other PHYs and need
to be initialized with a special irefgen bit in the PORT_COMP_DW8
register. Previously PHY A was the only compensation master (for PHYs
B & C), but RKL adds a fourth PHY which is slaved to PHY C instead.
Bspec: 49291
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-12-matthew.d.roper@intel.com
The pin mapping for the final two outputs varies according to which PCH
is present on the platform: with TGP the pins are remapped into the TC
range, whereas with CMP they stay in the traditional combo output range.
Bspec: 49181
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-9-matthew.d.roper@intel.com
RKL uses the DDI A, DDI B, DDI USBC1, DDI USBC2 from the DE point of
view, so all DDI/pipe/transcoder register use these indexes to refer to
them. Combo phy and IO functions follow another namespace that we keep
as "enum phy". The VBT in theory would use the DE point of view, but
that does not happen in practice.
Provide a table to convert the child devices to the "correct" port
numbering we use. Now this is the output we get while reading the VBT:
DDIA:
[drm:intel_bios_port_aux_ch [i915]] using AUX A for port A (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:275:DDI A]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:275:DDI A]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x1 for port A (VBT)
DDIB:
[drm:intel_bios_port_aux_ch [i915]] using AUX B for port B (platform default)
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:291:DDI B]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x2 for port B (VBT)
DDI USBC1:
[drm:intel_bios_port_aux_ch [i915]] using AUX D for port D (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:295:DDI D]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:295:DDI D]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x3 for port D (VBT)
DDI USBC2:
[drm:intel_bios_port_aux_ch [i915]] using AUX E for port E (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:306:DDI E]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:306:DDI E]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x9 for port E (VBT)
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-7-matthew.d.roper@intel.com
The DP spec says:
"When the combination of the requested pre-emphasis level and
voltage swing exceeds the capability of a DPTX, the DPTX shall
set the pre-emphasis level according to the request and use the
highest voltage swing it can output with the given pre-emphasis level."
and
"When a DPTX reads a request beyond the limits of this Standard,
the DPTX shall set the pre-emphasis level according to the request
and set the highest voltage swing level it can output with the
given pre-emphasis level. If a DPTX is requested for 9.5dB of
pre-emphasis level (may be supported for a DPTX) and cannot support
that level, it shall set the pre-emphasis level to the next
highest level, 6dB."
Ie. we should first validate the pre-emphasis, and then select
the appropriate vswing for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-6-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
According to the DP spec supporting vswing 1 + preemph 2 is
mandatory. We don't have the hw settings for that though. In
order to pretend to follow the DP spec let's just select
vswing 0 + preemph 2 in this case (the DP spec says to use
the requested preemph in preference to the vswing when the
requested values aren't supported).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
cpt/ppt support pre-emphasis level 3. Let's actually declare
support for it, instead of clamping things to level 2.
Also tweak the if-ladder in intel_dp_voltage_max() to match
intel_dp_pre_emphasis_max() to make it easier to compare them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cometlake is a small refresh of Coffeelake, but since we have found out a
difference in the plaforms, we need to identify them as separate platforms.
Since we previously took Coffeelake/Cometlake as identical, update all
IS_COFFEELAKE() to also include IS_COMETLAKE().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602140541.5481-1-chris@chris-wilson.co.uk
If an error is encountered during the DSI initialization setup, the
drm connector object also needs to be cleaned up along with the encoder.
The error can happen due to a missing mode in the VBT or for other
reasons.
v2: Rephrase the commit message to make it more clear.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522202630.7604-1-vivek.kasireddy@intel.com
While the current locking/serialization of the global state
suffices for protecting the obj->state access and the actual
hardware reprogramming, we do have a problem with accessing
the old/new states during nonblocking commits.
The state computation and swap will be protected by the crtc
locks, but the commit_tails can finish out of order, thus also
causing the atomic states to be cleaned up out of order. This
would mean the commit that started first but finished last has
had its new state freed as the no-longer-needed old state by the
other commit.
To fix this let's just refcount the states. obj->state amounts
to one reference, and the intel_atomic_state holds extra references
to both its new and old global obj states.
Fixes: 0ef1905ecf ("drm/i915: Introduce better global state handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527200245.13184-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit f8c86ffa28)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While the current locking/serialization of the global state
suffices for protecting the obj->state access and the actual
hardware reprogramming, we do have a problem with accessing
the old/new states during nonblocking commits.
The state computation and swap will be protected by the crtc
locks, but the commit_tails can finish out of order, thus also
causing the atomic states to be cleaned up out of order. This
would mean the commit that started first but finished last has
had its new state freed as the no-longer-needed old state by the
other commit.
To fix this let's just refcount the states. obj->state amounts
to one reference, and the intel_atomic_state holds extra references
to both its new and old global obj states.
Fixes: 0ef1905ecf ("drm/i915: Introduce better global state handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527200245.13184-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Currently the plane property doesn't have support for YCBCR_BT2020,
which enables the corresponding color conversion mode on plane CSC.
Enabling the plane property for the planes for GLK & ICL+ platforms.
Also as per spec, update the Plane Color CSC from YUV601_TO_RGB709
to YUV601_TO_RGB601.
V2: Enabling support for YCBCT_BT2020 for HDR planes on
platforms GLK & ICL
V3: Refined the condition check to handle GLK & ICL+ HDR planes
Also added BT2020 handling in glk_plane_color_ctl.
V4: Combine If-else into single If
V5: Drop the checking for HDR planes and enable YCBCR_BT2020
for platforms GLK & ICL+.
V6: As per Spec, update PLANE_COLOR_CSC_MODE_YUV601_TO_RGB709
to PLANE_COLOR_CSC_MODE_YUV601_TO_RGB601 as per Ville's
feedback.
V7: Rebased
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200601073544.11291-1-kishore.kadiyala@intel.com
There's no reason for I915_MODE_FLAG_INHERITED to exist as a flag
anymore. Just make it a boolean.
v2: Deal with sanitize_watermarks()
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103936.11850-1-ville.syrjala@linux.intel.com
Replace the use of mode->private_flags with a truly private bitmaks
in our own crtc state. We also need a copy in the crtc itself so the
vblank code can get at it. We already have scanline_offset in there
for a similar reason, as well as the vblank->hwmode which is assigned
via drm_calc_timestamping_constants(). Fortunately we now have a
nice place for doing the crtc_state->crtc copy in
intel_crtc_update_active_timings() which gets called both for
modesets and init/resume readout.
The one slightly iffy spot is the INHERITED flag which we want to
preserve until userspace/fb_helper does the first proper commit after
actually calling .detecti() on the connectors. Otherwise we don't have
the full sink capabilities (audio,infoframes,etc.) when .compute_config()
gets called and thus we will fail to enable those features when the
first userspace commit happens. The only internal commit we do prior to
that should be from intel_initial_commit() and there we can simply
preserve the INHERITED flag from the readout.
v2: Deal with INHERITED in sanitize_watermarks() as well
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103904.11727-1-ville.syrjala@linux.intel.com
The drrs code dereferences mode->vrefresh via some really long chain
of structures/pointers. Couldn't get coccinelle to see through all
that so let's add some local variables to help it.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-3-ville.syrjala@linux.intel.com
drivers/gpu/drm/i915/display/intel_dsb.c:177 intel_dsb_reg_write() warn: variable dereferenced before check 'dsb' (see line 175)
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200524233900.25598-1-chris@chris-wilson.co.uk
Pre-allocate command buffer in atomic_commit using intel_dsb_prepare
function which also includes pinning and map in cpu domain.
No functional change is dsb write/commit functions.
Now dsb get/put function is removed and ref-count mechanism is
not needed. Below dsb api added to do respective job mentioned
below.
intel_dsb_prepare - Allocate, pin and map the buffer.
intel_dsb_cleanup - Unpin and release the gem object.
RFC: Initial patch for design review.
v2: included _init() part in _prepare(). [Daniel, Ville]
v3: dsb_cleanup called after cleanup_planes. [Daniel]
v4: dsb structure is moved to intel_crtc_state from intel_crtc. [Maarten]
v5: dsb get/put/ref-count mechanism removed. [Maarten]
v6: Based on review feedback following changes are added,
- replaced intel_dsb structure by pointer in intel_crtc_state. [Maarten]
- passing intel_crtc_state to dsp-api to simplify the code. [Maarten]
- few dsb functions prototype modified to simplify code.
v7: added few cosmetic changes suggested by Jani and null check for
crtc_state in dsb_cleanup removed as suggested by Maarten.
v8: changed the function parameter to intel_crtc_state* of
ivb_load_lut_ext_max() from intel_crtc. [Maarten]
v9: error handling improved in _write() and prepare(). [Maarten]
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520130737.11240-1-animesh.manna@intel.com
Removed duplicate include and fixed comment > 80 chars.
v2: Added newline after system include and between functions
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522131843.20477-1-stanislav.lisovskiy@intel.com
According to BSpec max BW per slice is calculated using formula
Max BW = CDCLK * 64. Currently when calculating min CDCLK we
account only per plane requirements, however in order to avoid
FIFO underruns we need to estimate accumulated BW consumed by
all planes(ddb entries basically) residing on that particular
DBuf slice. This will allow us to put CDCLK lower and save power
when we don't need that much bandwidth or gain additional
performance once plane consumption grows.
v2: - Fix long line warning
- Limited new DBuf bw checks to only gens >= 11
v3: - Lets track used Dbuf bw per slice and per crtc in bw state
(or may be in DBuf state in future), that way we don't need
to have all crtcs in state and those only if we detect if
are actually going to change cdclk, just same way as we
do with other stuff, i.e intel_atomic_serialize_global_state
and co. Just as per Ville's paradigm.
- Made dbuf bw calculation procedure look nicer by introducing
for_each_dbuf_slice_in_mask - we often will now need to iterate
slices using mask.
- According to experimental results CDCLK * 64 accounts for
overall bandwidth across all dbufs, not per dbuf.
v4: - Fixed missing const(Ville)
- Removed spurious whitespaces(Ville)
- Fixed local variable init(reduced scope where not needed)
- Added some comments about data rate for planar formats
- Changed struct intel_crtc_bw to intel_dbuf_bw
- Moved dbuf bw calculation to intel_compute_min_cdclk(Ville)
v5: - Removed unneeded macro
v6: - Prevent too frequent CDCLK switching back and forth:
Always switch to higher CDCLK when needed to prevent bandwidth
issues, however don't switch to lower CDCLK earlier than once
in 30 minutes in order to prevent constant modeset blinking.
We could of course not switch back at all, however this is
bad from power consumption point of view.
v7: - Fixed to track cdclk using bw_state, modeset will be now
triggered only when CDCLK change is really needed.
v8: - Lock global state if bw_state->min_cdclk is changed.
- Try getting bw_state only if there are crtcs in the commit
(need to have read-locked global state)
v9: - Do not do Dbuf bw check for gens < 9 - triggers WARN
as ddb_size is 0.
v10: - Lock global state for older gens as well.
v11: - Define new bw_calc_min_cdclk hook, instead of using
a condition(Manasi Navare)
v12: - Fixed rebase conflict
v13: - Added spaces after declarations to make checkpatch happy.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520150058.16123-1-stanislav.lisovskiy@intel.com
We quite often need now to iterate only particular dbuf slices
in mask, whether they are active or related to particular crtc.
v2: - Minor code refactoring
v3: - Use enum for max slices instead of macro
Let's make our life a bit easier and use a macro for that.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-6-stanislav.lisovskiy@intel.com
Checking with hweight8 if plane configuration had
changed seems to be wrong as different plane configs
can result in a same hamming weight.
So lets check the bitmask itself.
v2: Fixed "from" field which got corrupted for some weird reason
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520145827.15887-1-stanislav.lisovskiy@intel.com
In Gen11+ whenever we might exceed DBuf bandwidth we might need to
recalculate CDCLK which DBuf bandwidth is scaled with.
Total Dbuf bw used might change based on particular plane needs.
Thus to calculate if cdclk needs to be changed it is not enough
anymore to check plane configuration and plane min cdclk, per DBuf
bw can be calculated only after wm/ddb calculation is done and
all required planes are added into the state. In order to keep
all min_cdclk related checks in one place let's extract it into
separate function, checking and modifying any_ms.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-3-stanislav.lisovskiy@intel.com
We need to calculate cdclk after watermarks/ddb has been calculated
as with recent hw CDCLK needs to be adjusted accordingly to DBuf
requirements, which is not possible with current code organization.
Setting CDCLK according to DBuf BW requirements and not just rejecting
if it doesn't satisfy BW requirements, will allow us to save power when
it is possible and gain additional bandwidth when it's needed - i.e
boosting both our power management and perfomance capabilities.
This patch is preparation for that, first we now extract modeset
calculation from modeset checks, in order to call it after wm/ddb
has been calculated.
v2: - Extract only intel_modeset_calc_cdclk from intel_modeset_checks
(Ville Syrjälä)
v3: - Clear plls after intel_modeset_calc_cdclk
v4: - Added r-b from previous revision to commit message
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-2-stanislav.lisovskiy@intel.com
Since the number of platforms with this restriction are growing, let's
separate out the platform logic into a has_phy_misc() function.
Bspec: 50107
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-11-matthew.d.roper@intel.com
RKL power wells are similar to TGL power wells, but have some important
differences:
* PG1 now has pipe A's VDSC (rather than sticking it in PG2)
* PG2 no longer exists
* DDI-C (aka TC-1) moves from PG1 -> PG3
* PG5 no longer exists due to the lack of a fourth pipe
Also note that what we refer to as 'DDI-C' and 'DDI-D' need to actually
be programmed as TC-1 and TC-2 even though this platform doesn't have TC
outputs.
Bspec: 49234
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-9-matthew.d.roper@intel.com
RKL only has five universal planes, plus a cursor. Since the
bottom-most universal plane is considered the primary plane, set the
number of sprites available on this platform to 4.
In general, the plane capabilities of the remaining planes stay the same
as TGL. However the NV12 Y-plane support moves down to the new top two
planes and now only the bottom three planes can be used for NV12 UV.
Bspec: 49181
Bspec: 49251
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-8-matthew.d.roper@intel.com
The RKL platform has different memory characteristics from past
platforms. Update the values used by our memory bandwidth calculations
accordingly.
Bspec: 53998
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-7-matthew.d.roper@intel.com
UAPI Changes:
- drm/i915: Show per-engine default property values in sysfs
By providing the default values configured into the kernel via sysfs, it
is much more convenient for userspace to restore those sane defaults, or
at least know what are considered good baseline. This is useful, for
example, to cleanup after any failed userspace prior to commencing new
jobs.
Cross-subsystem Changes:
- video/hdmi: Add Unpack only function for DRM infoframe
- Includes pull request gvt-next-2020-05-12
Driver Changes:
- Restore Cherryview back to full-ppgtt (Chris, Mika)
- Document locking guidelines for i915 (Chris, Daniel, Joonas)
- Fix GitLab #1746: Handle idling during i915_gem_evict_something busy loops (Chris)
- Display WA #1105: Require linear fb stride to be multiple of 512 bytes on
gen9/glk (Ville)
- Add Wa_14010685332 for ICP/ICL (Matt R)
- Restrict w/a 1607087056 for EHL/JSL (Swathi)
- Fix interrupt handling for DP AUX transactions on Tigerlake (Imre)
- Revert "drm/i915/tgl: Include ro parts of l3 to invalidate" (Mika)
- Fix HDC pipeline flush hardware bit on Gen12 (Mika)
- Flush L3 when flushing render on Gen12 (Mika)
- Invalidate aux table entries forcibly between BB on Gen12 (Mika)
- Add aux table invalidate for all engines on Gen12 (Mika)
- Force pte cacheline to main memory Gen8+ (Mika)
- Add and enable TGL+ SAGV support (Stanislav)
- Implement vm_ops->access on i915 mmaps for GDB (Chris, Kristian)
- Replace zero-length array with flexible-array (Gustavo)
- Improve batch buffer pool effectiveness to mitigate soft-rc6 hit (Chris)
- Remove wait priority boosting (Chris)
- Keep driver module referenced when PMU is active (Chris)
- Sanitize RPS interrupts upon resume (Chris)
- Extend pcode read timeout to 20 ms (Chris)
- Wait for ACT sent before enabling MST pipe (Ville)
- Extend support to async relocations to SNB (Chris)
- Remove CNL pre-prod workarounds (Ville)
- Don't enable WaIncreaseLatencyIPCEnabled when IPC is disabled (Sultan)
- Record the active CCID from before reset (Chris)
- Mark concurrent submissions with a weak-dependency (Chris)
- Peel dma-fence-chains for await to allow engine-to-engine sync (Lionel)
- Prevent using semaphores to chain up to external fences (Chris)
- Fix GLK watermark calculations (Ville)
- Emit await(batch) before MI_BB_START (Chris)
- Reset execlists registers before HWSP (Chris)
- Drop no-semaphore boosting in favor of fast timeslicing (Chris)
- Fix enabled infoframe states of lspcon (Gwan-gyeong)
- Program DP SDPs on pipe updates (Gwan-gyeong)
- Stop sending DP SDPs on ddi disable (Gwan-gyeong)
- Store CS timestamp frequency in Hz (Ville)
- Remove unused HAS_FWTABLE macro (Pascal)
- Use batchbuffer chaining for relocations to save ring space (Chris)
- Try different engines for relocs if MI ops not supported (Chris, Tvrtko)
- Lazily acquire the device wakeref for freeing objects (Chris)
- Streamline display code arithmetics around rounding etc. (Ville)
- Use bw state for per crtc SAGV evaluation (Stanislav)
- Track active_pipes in bw_state (Stanislav)
- Nuke mode.vrefresh usage (Ville)
- Warn if the FBC is still writing to stolen on removal (Chris)
- Added new PCode commands prepping for QGV rescricting (Stansilav)
- Stop holding onto the pinned_default_state (Chris)
- Propagate error from completed fences (Chris)
- Ignore submit-fences on the same timeline (Chris)
- Pull waiting on an external dma-fence into its routine (Chris)
- Replace the hardcoded I915_FENCE_TIMEOUT with Kconfig (Chris)
- Mark up the racy read of execlists->context_tag (Chris)
- Tidy up the return handling for completed dma-fences (Chris)
- Introduce skl_plane_wm_level accessor (Stanislav)
- Extract SKL SAGV checking (Stanislav)
- Make active_pipes check skl specific (Stanislav)
- Suspend tasklets before resume sanitization (Chris)
- Remove redundant exec_fence (Chris)
- Mark the addition of the initial-breadcrumb in the request (Chris)
- Transfer old virtual breadcrumbs to irq_worker (Chris)
- Read the DP SDPs from the video DIP (Gwan-gyeong)
- Program DP SDPs with computed configs (Gwan-gyeong)
- Add state readout for DP VSC and DP HDR Metadata Infoframe SDP
(Gwan-gyeong)
- Add compute routine for DP PSR VSC SDP (Gwan-gyeong)
- Use new DP VSC SDP compute routine on PSR (Gwan-gyeong)
- Restrict qgv points which don't have enough bandwidth. (Stanislav)
- Nuke pointless div by 64bit (Ville)
- Static checker code fixes (Nathan, Mika, Chris)
- Add logging function for DP VSC SDP (Gwan-gyeong)
- Include HDMI DRM infoframe, DP HDR metadata and DP VSC SDP in the
crtc state dump (Gwan-gyeong)
- Make timeslicing explicit engine property (Chris, Tvrtko)
- Selftest and debugging improvements (Chris)
- Align variable names with BSpec (Ville)
- Tidy up gen8+ breadcrumb emission code (Chris)
- Turn intel_digital_port_connected() in a vfunc (Ville)
- Use stashed away hpd isr bits in intel_digital_port_connected() (Ville)
- Extract i915_cs_timestamp_{ns_to_ticks,tick_to_ns}() (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515160703.GA19043@jlahtine-desk.ger.corp.intel.com
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
(cherry picked from commit ae9b6cfe13)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:
drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~
Move the function itself into that #ifdef as well.
Fixes: 81b55ef1f4 ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de
(cherry picked from commit 794bdcf71f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON.
Conversion is done with below sementic patch:
@@
identifier func, T;
@@
func(...) {
...
struct drm_i915_private *T = ...;
<+...
-WARN_ON(
+drm_WARN_ON(&T->drm,
...)
...+>
}
@@
identifier func, T;
@@
func(struct intel_digital_port *T,...) {
+struct drm_i915_private *i915 = to_i915(T->base.base.dev);
<+...
-WARN_ON(
+drm_WARN_ON(&i915->drm,
...)
...+>
}
changes since v1:
- Add i915 local variable and use it in drm_WARN_ON (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-5-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN* over WARN* calls.
changes since v1:
- Added dev_priv local variable and used it in drm_WARN* calls (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-4-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct i915_power_domains
struct is available.
Conversion is done with below sementic patch:
@@
identifier func, T;
@@
func(struct i915_power_domains *T,...) {
+ struct drm_i915_private *i915 = container_of(T, struct drm_i915_private, power_domains);
<+...
-WARN_ON(
+drm_WARN_ON(&i915->drm,
...)
...+>
}
changes since v1:
- Fix commit subject (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-2-pankaj.laxminarayan.bharadiya@intel.com
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
I've checked a bunch of gen3/4 machines and all seem to have
consistent FSB frequency information in the CLKCFG register.
So let's read out hrawclk on all gen3+ machines. Although
apart from g4x/pnv aux/pps dividers we only really need this
for for i965g/gm cs timestamp increment.
The CLKCFG memory clock values seem less consistent but we
don't care about those here.
For posterity here's a list of CLKCFG vs. FSB dumps from
a bunch of machines (only missing lpt for a full set):
machine CLKCFG FSB
alv1 0x00001411 533
alv2 0x00000420 400 (Chris)
gdg1 0x20000022 800
gdg2 0x20000022 800
cst 0x00010043 666
blb 0x00002034 1333
pnv1 0x00000423 666
pnv2 0x00000433 666
965gm 0x00004342 800
946gz 0x00000022 800
965g 0x00000422 800
g35 0x00000430 1066
0x00000434 1333
ctg1 0x00644056 1066
ctg2 0x00644066 1066
elk1 0x00012420 1066
0x00012424 1333
0x00012436 1600
0x00012422 800
elk2 0x00012040 1066
For the mobile parts the chipset docs generally have these
documented to some degree (alv being the exception).
The two settings w/o any evidence are 0x5=400MHz on desktop
and 0x7=1333MHz on mobile. Though the mobile 1333MHz case
probably doesn't even exist since ctg is only documented
to go up to 1066MHz.
v2: Fix 400mhz readout for Chris's alv/celeron machine
Do a clean mobile vs. dekstop split since that's really
what seems to be going on
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-3-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Document the fact that we aren't reading out the actual FSB
frequency but rather just the state of the FSB straps.
Some BIOSen allow you to configure the two independently.
So if someone sets the two up in an inconsistent manner
we'll get the wrong answer here and thus will end up with
incorrect aux/pps clock dividers. Alas, proper docs are no
longer around so we can't do any better.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Looks like elk redefines some of the CLKCFG FSB values to
make room for 400 MHz FSB. The setting overlaps with one of
the 266MHz settings (which is even documented in the ctg docs,
and cofirmed to be correct on my ctg). So we limit the special
case to elk only.
Though it might also be that we have some kind of desktop vs.
mobile difference going on here as eg. both g35 and elk
use 0x0 for the 266 MHz setting, vs. 0x6 used by ctg). The
g35 doesn't let me select 400MHz for the FSB strap so can't
confirm which way it would go here. But anyways as it seems
only elk has the 400MHz option we shouldn't lose anything
by limiting the special case to it alone.
My earlier experiments on this appear to have been nonsense as
the comment I added claims that FSB strap of 400MHz results in
a value of 0x4, but I've now retested it and I definitely get a
value of 0x6 instead. So let's remove that bogus comment.
v2: s/_ELK/_ALT/ in the define in anticipation of a full
mobile vs. desktop CLKCFG split
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Encapsulate the dbuf state more by moving the pre/post
plane functions out from intel_display.c. We stick them
into intel_pm.c since that's where the rest of the code
lives for now.
Eventually we should add a new file for this stuff at which
point we also need to decide if it makes sense to even split
the wm code from the ddb code, or to keep them together.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-11-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Add a global state to track the dbuf slices. Gets rid of all the nasty
coupling between state->modeset and dbuf recomputation. Also we can now
totally nuke state->active_pipe_changes.
dev_priv->wm.distrust_bios_wm still remains, but that too will get
nuked soon.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The low level dbuf slice code is rather inconsitent with its
functiona naming and organization. Make it more consistent.
Also share the enable/disable functions between all platforms
since the same code works just fine for all of them.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-8-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Polish some of the dbuf code to give more meaningful debug
messages and whatnot. Also we can switch over to the per-device
debugs/warns at the same time.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-7-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:
drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~
Move the function itself into that #ifdef as well.
Fixes: 81b55ef1f4 ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de
Put the overlay color conversion unit into 10bit mode if the
pipe isn't using the 8bit legacy gamma. Not 100% sure this is
what the intention of the bit was but makes at least some sense to
me.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-4-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
As with the video sprites the colorkey is always specified
as 8bpc. For 10bpc primary plane formats we just ignore the
two lsbs of each component. For C8 we'll replicate the same
key to each chanel, which is what the hardware wants.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Apparently the 128x128 and 256x256 ARGB cursor modes were
only added on LPT/CST.
While the display section of bspec isn't super clear on the
subject, it does highlight these two modes in a different
color, has a few changlog entries indicating the 256x256 mode
was added for a LPT DCN, and that the 128x128 mode was also
added later (though no DCN/platform note there).
The "device dependencies" bspec section does list the 256x256x32
as a new feature for LPT/CST, and goes on to mention that current
hw only has the 64x64x32 mode (which reinforces the notion that
the 128x128 mode was also added at the same time).
Testing on actual hardware confirms all of this. CI shows all
the 128x128 and 256x256 tests failing on GDG, and my ALV
definitely doesn't like them.
So we shall limit GDG/ALV to 64x64 only. And while at it
let's adjust the mobile gen2 case to list the two platforms
explicitly so that the if-ladder looks reasonably uniform.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-2-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
According to BSpec 53998, we should try to
restrict qgv points, which can't provide
enough bandwidth for desired display configuration.
Currently we are just comparing against all of
those and take minimum(worst case).
v2: Fixed wrong PCode reply mask, removed hardcoded
values.
v3: Forbid simultaneous legacy SAGV PCode requests and
restricting qgv points. Put the actual restriction
to commit function, added serialization(thanks to Ville)
to prevent commit being applied out of order in case of
nonblocking and/or nomodeset commits.
v4:
- Minor code refactoring, fixed few typos(thanks to James Ausmus)
- Change the naming of qgv point
masking/unmasking functions(James Ausmus).
- Simplify the masking/unmasking operation itself,
as we don't need to mask only single point per request(James Ausmus)
- Reject and stick to highest bandwidth point if SAGV
can't be enabled(BSpec)
v5:
- Add new mailbox reply codes, which seems to happen during boot
time for TGL and indicate that QGV setting is not yet available.
v6:
- Increase number of supported QGV points to be in sync with BSpec.
v7: - Rebased and resolved conflict to fix build failure.
- Fix NUM_QGV_POINTS to 8 and moved that to header file(James Ausmus)
v8: - Don't report an error if we can't restrict qgv points, as SAGV
can be disabled by BIOS, which is completely legal. So don't
make CI panic. Instead if we detect that there is only 1 QGV
point accessible just analyze if we can fit the required bandwidth
requirements, but no need in restricting.
v9: - Fix wrong QGV transition if we have 0 planes and no SAGV
simultaneously.
v10: - Fix CDCLK corruption, because of global state getting serialized
without modeset, which caused copying of non-calculated cdclk
to be copied to dev_priv(thanks to Ville for the hint).
v11: - Remove unneeded headers and spaces(Matthew Roper)
- Remove unneeded intel_qgv_info qi struct from bw check and zero
out the needed one(Matthew Roper)
- Changed QGV error message to have more clear meaning(Matthew Roper)
- Use state->modeset_set instead of any_ms(Matthew Roper)
- Moved NUM_SAGV_POINTS from i915_reg.h to i915_drv.h where it's used
- Keep using crtc_state->hw.active instead of .enable(Matthew Roper)
- Moved unrelated changes to other patch(using latency as parameter
for plane wm calculation, moved to SAGV refactoring patch)
v12: - Fix rebase conflict with own temporary SAGV/QGV fix.
- Remove unnecessary mask being zero check when unmasking
qgv points as this is completely legal(Matt Roper)
- Check if we are setting the same mask as already being set
in hardware to prevent error from PCode.
- Fix error message when restricting/unrestricting qgv points
to "mask/unmask" which sounds more accurate(Matt Roper)
- Move sagv status setting to icl_get_bw_info from atomic check
as this should be calculated only once.(Matt Roper)
- Edited comments for the case when we can't enable SAGV and
use only 1 QGV point with highest bandwidth to be more
understandable.(Matt Roper)
v13: - Moved max_data_rate in bw check to closer scope(Ville Syrjälä)
- Changed comment for zero new_mask in qgv points masking function
to better reflect reality(Ville Syrjälä)
- Simplified bit mask operation in qgv points masking function
(Ville Syrjälä)
- Moved intel_qgv_points_mask closer to gen11 SAGV disabling,
however this still can't be under modeset condition(Ville Syrjälä)
- Packed qgv_points_mask as u8 and moved closer to pipe_sagv_mask
(Ville Syrjälä)
- Extracted PCode changes to separate patch.(Ville Syrjälä)
- Now treat num_planes 0 same as 1 to avoid confusion and
returning max_bw as 0, which would prevent choosing QGV
point having max bandwidth in case if SAGV is not allowed,
as per BSpec(Ville Syrjälä)
- Do the actual qgv_points_mask swap in the same place as
all other global state parts like cdclk are swapped.
In the next patch, this all will be moved to bw state as
global state, once new global state patch series from Ville
lands
v14: - Now using global state to serialize access to qgv points
- Added global state locking back, otherwise we seem to read
bw state in a wrong way.
v15: - Added TODO comment for near atomic global state locking in
bw code.
v16: - Fixed intel_atomic_bw_* functions to be intel_bw_* as discussed
with Jani Nikula.
- Take bw_state_changed flag into use.
v17: - Moved qgv point related manipulations next to SAGV code, as
those are semantically related(Ville Syrjälä)
- Renamed those into intel_sagv_(pre)|(post)_plane_update
(Ville Syrjälä)
v18: - Move sagv related calls from commit tail into
intel_sagv_(pre)|(post)_plane_update(Ville Syrjälä)
v19: - Use intel_atomic_get_bw_(old)|(new)_state which is intended
for commit tail stage.
v20: - Return max bandwidth for 0 planes(Ville)
- Constify old_bw_state in bw_atomic_check(Ville)
- Removed some debugs(Ville)
- Added data rate to debug print when no QGV points(Ville)
- Removed some comments(Ville)
v21, v22, v23: - Fixed rebase conflict
v24: - Changed PCode mask to use ICL_ prefix
v25: - Resolved rebase conflict
v26: - Removed redundant NULL checks(Ville)
- Removed redundant error prints(Ville)
v27: - Use device specific drm_err(Ville)
- Fixed parenthesis ident reported by checkpatch
Line over 100 warns to be fixed together with
existing code style.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
[vsyrjala: Drop duplicate intel_sagv_{pre,post}_plane_update() prototypes
and drop unused NUM_SAGV_POINTS define]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-3-stanislav.lisovskiy@intel.com
Starting from TGL we need to have a separate wm0
values for SAGV and non-SAGV which affects
how calculations are done.
v2: Remove long lines
v3: Removed COLOR_PLANE enum references
v4, v5, v6: Fixed rebase conflict
v7: - Removed skl_plane_wm_level accessor from skl_allocate_pipe_ddb(Ville)
- Removed sagv_uv_wm0(Ville)
- can_sagv->use_sagv_wm(Ville)
v8: - Moved tgl_crtc_can_enable_sagv function up(Ville)
- Changed comment regarding pipe_wm usage(Ville)
- Call intel_can_enable_sagv and tgl_compute_sagv_wm only
for Gen12(Ville)
- Some sagv debugs removed(Ville)
- skl_print_wm_changes improvements(Ville)
- Do assignment instead of memcpy in
skl_pipe_wm_get_hw_state(Ville)
v9: - Removed can_sagv variable(Ville)
- Removed spurious line(Ville)
- Changed u32 to unsigned int as agreed(Ville)
- Assign sagv only for gen12 in
skl_pipe_wm_get_hw_state(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Remove the dead 'return false' from intel_crtc_can_enable_sagv()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-2-stanislav.lisovskiy@intel.com
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.
In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.
There are no changes to PSR mechanism.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
infoframes.enable.
It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-15-gwan-gyeong.mun@intel.com
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it adds a compute routine for PSR VSC SDP.
As PSR routine can not use infoframes.vsc of crtc state, it also adds new
writing of DP SDPs (Secondary Data Packet) for PSR.
PSR routine has its own scenario and timings of writing a VSC SDP.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: 1) Fix packing of VSC SDP where Pixel Encoding/Colorimetry Format is
not supported.
2) Change a checking of PSR state.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-14-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes(false) function on intel_ddi_post_disable_dp()
to make sure not to send VSC SDP and HDR Metadata Infoframe SDP.
v5: Polish commit message [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-13-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-12-gwan-gyeong.mun@intel.com
Compared to implementation of DP and HDMI's encoder->infoframes_enabled,
the lspcon's implementation returns its active state. (we expect enabled
infoframe states of HW.) It leads to pipe state mismatch error
when ddi_get_config is called.
Because the current implementation of lspcon is not ready to support
readout infoframes, we need to return 0 here.
In order to support readout to lspcon, we need to implement read_infoframe
and infoframes_enabled. And set_infoframes also have to set an appropriate
bit on crtc_state->infoframes.enable
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-11-gwan-gyeong.mun@intel.com
Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-10-gwan-gyeong.mun@intel.com
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
Dump out the DP VSC SDP in the normal crtc state dump
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
Use drm core's DP VSC SDP logging function
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-7-gwan-gyeong.mun@intel.com
Dump out the DP HDR Metadata Infoframe SDP in the normal crtc state dump.
HDMI Dynamic Range and Mastering (DRM) infoframe and DP HDR Metadata
Infoframe SDP use the same member variable in infoframes of crtc state.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-6-gwan-gyeong.mun@intel.com
It adds code to read the DP SDPs from the video DIP and unpack them into
the crtc state.
It adds routines that read out DP VSC SDP and DP HDR Metadata Infoframe SDP
In order to unpack DP VSC SDP, it adds intel_dp_vsc_sdp_unpack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to unpack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_unpack(). And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A naming rule and style of intel_read_dp_sdp() function references
intel_read_infoframe() function of intel_hdmi.c
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v5: Addressed review comments from Uma
- Polish commit message and comments
- Combine the if checks of sdp.HB2 and sdp.HB3
- Add 6bpc to unpacking of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-3-gwan-gyeong.mun@intel.com
Driver Changes:
- Fix GitLab #1698: Performance regression with Linux 5.7-rc1 on
Iris Plus 655 and 4K screen (Chris)
- Add Wa_14011059788 for Tigerlake (Matt A)
- Add per ctx batchbuffer wa for timestamp for Gen12 (Mika)
- Use indirect ctx bb to load cmd buffer control value
from context image to avoid corruption (Mika)
- Enable DP Display Audio WA (Uma, Jani)
- Update forcewake firmware ranges for Icelake (Radhakrishna)
- Add missing deinitialization cases of load failure for display (Jose)
- Implement TC cold sequences for Icelake and Tigerlake (Jose)
- Unbreak enable_dpcd_backlight modparam (Lyude)
- Move the late flush_submission in retire to the end (Chris)
- Demote "Reducing compressed framebufer size" message to info (Peter)
- Push MST link retraining to the hotplug work (Ville)
- Hold obj->vma.lock over for_each_ggtt_vma() (Chris)
- Fix timeout handling during TypeC AUX power well enabling for ICL (Imre)
- Fix skl+ non-scaled pfit modes (Ville)
- Prefer soft-rc6 over RPS DOWN_TIMEOUT (Chris)
- Sanitize GT first before poisoning HWSP (Chris)
- Fix up clock RPS frequency readout (Chris)
- Avoid reusing the same logical CCID (Chris)
- Avoid dereferencing a dead context (Chris)
- Always enable busy-stats for execlists (Chris)
- Apply the aggressive downclocking to parking (Chris)
- Restore aggressive post-boost downclocking (Chris)
- Scrub execlists state on resume (Chris)
- Add debugfs attributes for LPSP (Ansuman)
- Improvements to kernel selftests (Chris, Mika)
- Add tiled blits selftest (Zbigniew)
- Fix error handling in __live_lrc_indirect_ctx_bb() (Dan)
- Add pre/post plane updates for SAGV (Stanislav)
- Add ICL PG3 PW ID for EHL (Anshuman)
- Fix Sphinx build duplicate label warning (Jani)
- Error log non-zero audio power refcount after unbind (Jani)
- Remove object_is_locked assertion from unpin_from_display_plane (Chris)
- Use single set of AUX powerwell ops for gen11+ (Matt R)
- Prefer drm_WARN_ON over WARN_ON (Pankaj)
- Poison residual state [HWSP] across resume (Chris, Tvrtko)
- Convert request-before-CS assertion to debug (Chris)
- Carefully order virtual_submission_tasklet (Chris)
- Check carefully for an idle engine in wait-for-idle (Chris)
- Only close vma we open (Chris)
- Trace RPS events (Chris)
- Use the RPM config register to determine clk frequencies (Chris)
- Drop rq->ring->vma peeking from error capture (Chris)
- Check preempt-timeout target before submit_ports (Chris)
- Check HWSP cacheline is valid before acquiring (Chris)
- Use proper fault mask in interrupt postinstall too (Matt R)
- Keep a no-frills swappable copy of the default context state (Chris)
- Add atomic helpers for bandwidth (Stanislav)
- Refactor setting dma info to a common helper from device info (Michael)
- Refactor DDI transcoder code for clairty (Ville)
- Extend PG3 power well ID to ICL (Anshuman)
- Refactor PFIT code for readability and future extensibility (Ville)
- Clarify code split between intel_ddi.c and intel_dp.c (Ville)
- Move out code to return the digital_port of the aux ch (Jose)
- Move rps.enabled/active and use of RPS interrupts to flags (Chris)
- Remove superfluous inlines and dead code (Jani)
- Re-disable -Wframe-address from top-level Makefile (Nick)
- Static checker and spelling fixes (Colin, Nathan)
- Split long lines (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430124904.GA100924@jlahtine-desk.ger.corp.intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507185408.GA14561@embeddedor
Expose the hardcoded timeout for unsignaled foreign fences as a Kconfig
option, primarily to allow brave systems to disable the timeout and
solely rely on correct signaling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200509105021.12542-1-chris@chris-wilson.co.uk
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl6ztuYACgkQaA3BHVML
eiMWaAgAvYpXvBqBfE/5jOTa1zWQUX9VMbmMDUqSAgec5r/HVHjmlbsDWkLff2XG
rH7T2shMNJwluoCleHfRFYUfyUWMmXoMgri1elnf4EgddmekLZ6vNQjtAYMRFUfL
7VegcFw5D5Z28uxK5YGnaaSQob34LvD8UTgvnCVfDQzCjcEzGYi1d9XELm7kTHje
dF2FOWPeF8FTqP0XHM8RrHNXW/pUPy9qErpmb2bWYBQp7ebkI2Q4p6IZIpRQm757
bnKPIdMEcy4BWMk1xtzjEYEb4bGSZhozJUWKFwpm/AHNvTrQCt9hn0GSVrXiqBcR
UKb42BRxEVR29C/4n10pUcnnQmmi+Q==
=yzZ9
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-05-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.8:
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507072503.GA10979@linux-uq9g
All these ROUNDING_FACTORs and whatnot are making this thing hard to
read. Get rid of them. And let's massage some of the fractions to
give us less questionable intermediate results and perhaps less
divisions.
Also looks like a good helping of 64bit math stuff is needed to
avoid some of overflows present in the current code. There
might still be a few overflows, namely when calculating
link_clks_available/samples_room (would require a huge hblank
though), and potentially when calculating hblank_rise (not sure
how large link_clks_active can get).
It looks like we're still not calculating exactly what the spec says
since we truncate tu_data and tu_line early. But I'm too lazy to
figure out if we could avoid that.
v2: Fix typo in commit msg (Uma)
Remove ROUNDING_FACTOR define (Uma)
s/5*link_clk+5*cdclk/5*(link_clk+cdclk)/ (Chris)
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Since the code seems insistent on using the variable names from the
bspec formulat, let's be consistent and use those names for all
the things. For some reason 'link_clk' and 'lanes' were left out
in the code until now.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
mode.vrefresh is rounded to the nearest integer. You don't want to use
it anywhere that requires precision. Also I want to nuke it.
vtotal*vrefresh == 1000*clock/htotal, so let's use the latter.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Display WA #1105 says that FBC requires PLANE_STRIDE to be a multiple
of 512 bytes on gen9 and glk.
This is definitely true for glk as certain tests (such as
igt/kms_big_fb/linear-16bpp-rotate-0) are now failing when the
display resolution results in a plane stride which is not a
multiple of 512 bytes.
Curiously I was not able to reproduce this on a KBL. First I
suspected that our use of the FBC override stride explain this,
but after trying to use the override stride on glk the test
still failed. I did try both the old CHICKEN_MISC_4 way and
the new FBC_STRIDE way, neither had any effect on the result.
Anyways, we need this at least on glk. But let's trust the spec
and apply the w/a for all gen9 as well, despite being unable to
reproduce the problem.
v2: s/FBC_CHICKEN/FBC_STRIDE/ in commit msg
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 691f7ba58d ("drm/i915/display/fbc: Make fences a nice-to-have for GEN9+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
That is a preparation patch before next one where we
introduce old_bw_state and a bunch of other changes
as well.
In a review comment it was suggested to split out
at least that renaming into a separate patch, what
is done here.
v2: Removed spurious space
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200423075902.21892-8-stanislav.lisovskiy@intel.com
We need to calculate SAGV mask also in a non-modeset
commit, however currently active_pipes are only calculated
for modesets in global atomic state, thus now we will be
tracking those also in bw_state in order to be able to
properly access global data.
v2: - Removed pre/post plane SAGV updates from modeset(Ville)
- Now tracking active pipes in intel_can_enable_sagv(Ville)
v3: - lock global state if active_pipes change as well(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430195634.7666-1-stanislav.lisovskiy@intel.com
Future platforms require per-crtc SAGV evaluation
and serializing global state when those are changed
from different commits.
v2: - Add has_sagv check to intel_crtc_can_enable_sagv
so that it sets bit in reject mask.
- Use bw_state in intel_pre/post_plane_enable_sagv
instead of atomic state
v3: - Fixed rebase conflict, now using
intel_atomic_crtc_state_for_each_plane_state in
order to call it from atomic check
v4: - Use fb modifier from plane state
v5: - Make intel_has_sagv static again(Ville)
- Removed unnecessary NULL assignments(Ville)
- Removed unnecessary SAGV debug(Ville)
- Call intel_compute_sagv_mask only for modesets(Ville)
- Serialize global state only if sagv results change, but
not mask itself(Ville)
v6: - use lock global state instead of serialize(Ville)
v7: - use both global state lock and serialize depending on
if we need to change only global state or access hw
(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430191757.18206-1-stanislav.lisovskiy@intel.com
Let's just calculate the hsync rate on demand. No point in wasting
space storing it and risking the cached value getting out of sync
with reality.
v2: Move drm_mode_hsync() next to its only users
Drop the TODO
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-2-ville.syrjala@linux.intel.com
Pass the entire connector state to intel_{gmch,pch}_panel_fitting().
For now we just need to get at .scaling_mode but in the future we'll
want access to the margin properties as well.
v2: Deal with intel_dp_ycbcr420_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Make things a bit more abstract by replacing the pch_pfit.pos/size
raw register values with a drm_rect. Makes it slighly more convenient
to eg. compute the scaling factors.
v2: Use drm_rect_init()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Most of the pfit functions are of the form:
func()
{
if (pfit_enabled) {
...
}
}
Flip the pfit_enabled check around to flatten the functions.
And while we're touching all this let's do the usual
s/pipe_config/crtc_state/ replacement.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-2-ville.syrjala@linux.intel.com
Fix skl_update_scaler_crtc() to deal with different scaling
modes correctly. The current implementation assumes
DRM_MODE_SCALE_FULLSCREEN. Fortunately we don't expose any
border properties currently so the code does actually end
up doing the right thing (assigning a scaler for pfit).
The code does need to be fixed before any borders are
exposed.
Also we have redundant calls to skl_update_scaler_crtc() in
dp/hdmi .compute_config() which can be nuked. They were anyway
called before we had even computed the pfit state so were
basically nonsense. The real call we need to keep is in
intel_crtc_atomic_check().
v2: Deal witrh skl_update_scaler_crtc() in intel_dp_ycbcr420_config()
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-1-ville.syrjala@linux.intel.com
Fix the check for when an AUX power well enabling timeout is expected on
a legacy TypeC port.
Fixes: 89e01caac6 ("drm/i915: Use single set of AUX powerwell ops for gen11+")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422123440.19522-1-imre.deak@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct drm_device
pointer can be extracted.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406112800.23762-8-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct drm_device
pointer can be extracted.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406112800.23762-5-pankaj.laxminarayan.bharadiya@intel.com
The early check for compressed_bpp being zero is too early, as it is hit
also when DSC is not enabled. Move the checks down to where the values
are actually needed. This is a paranoid check for a situation that
should not happen, so we don't really care about handling it gracefully
apart from not oopsing.
Fixes: 48b8b04c79 ("drm/i915/display: Enable DP Display Audio WA")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1750
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420131632.23283-1-jani.nikula@intel.com
Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com
AUX power wells sometimes need additional handling besides just
programming the specific power well registers:
* Type-C PHY's also require additional Type-C register programming
* ICL combo PHY's require additional workarounds
* TGL & EHL combo PHY's can be treated like any other power well
Today we have dedicated aux ops for the ICL combo PHY and Type-C cases.
This works fine, but means that when a new platform shows up with
identical general power well handling, but different types of PHYs on
its outputs, we have to define an entire new power well table for that
platform and can't just re-use the table from the earlier platform -- as
an example, see ehl_power_wells[], which is a subset of
icl_power_wells[], *except* that we need to specify different AUX ops
for the third display.
If we instead create a single set of top-level aux ops that will check
the PHY type and then dispatch to the appropriate handlers, we can get
more reuse out of our power well definitions. This allows us to
immediately eliminate ehl_power_wells[] and simply reuse the ICL table;
if future platforms follow the same general power well assignments as
either ICL or TGL, we'll be able to re-use those tables in the same way.
Note that I've only changed ICL+ platforms over to using the new icl_aux
ops; at this point it's unlikely that we'll have any new platforms that
re-use gen9 or earlier power well configurations.
v2:
- ICL_AUX_PW_TO_PHY() won't return the proper PHY for TBT AUX power
wells. But we know those wells will only used on Type-C outputs
anyway, so we can just check is is_tc_tbt flag in the condition.
(Jose).
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-2-matthew.d.roper@intel.com
We shouldn't try to do link retraining from the short hpd handler.
We can't take any modeset locks there so this is racy as hell.
Push the whole thing into the hotplug work like we do with SST.
We'll just have to adjust the SST retraining code to deal with
the MST encoders and multiple pipes.
TODO: I have a feeling we should just rip this all out and
do a full modeset instead. Stuff like port sync and the tgl+
MST master transcoder stuff maybe doesn't work well if we
try to retrain without following the proper modeset sequence.
So far haven't done any actual tests to confirm that though.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-2-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Make intel_dp_check_mst_status() somewhat legible by humans.
Note that the return value of drm_dp_mst_hpd_irq() is always
either 0 or -ENOMEM, and we never did anything with the latter
so we can just ignore the whole thing.
We can also get rid of the direct drm_dp_mst_topology_mgr_set_mst(false)
call since returning -EINVAL causes the caller to do the very same call
for us.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Pass the encoder all the way down to
intel_ddi_transcoder_func_reg_val_get(). Allows us eliminate the
intel_ddi_get_crtc_encoder() eyesore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Push the TRANS_DDI_FUNC_CTL into the encoder enable hook. The disable
is already there, and as a followup will enable us to pass the encoder
all the way down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
No reason that I can see why we should enable TRANS_DDI_FUNC_CTL
before we set up the watermarks of configure the mbus stuff.
In fact reordering these seems to match the bspec sequence better,
and crucially will allow us to push the TRANS_DDI_FUNC_CTL enable
into the encoder enable hook as a followup.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-2-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Since intel_ddi_enable_pipe_clock() was pushed down into the
encoder hooks we can pass on the encoder instead of having
to use intel_ddi_get_crtc_encoder().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
This was sort of annoying me:
random:~$ dmesg | tail -1
[523884.039227] [drm] Reducing the compressed framebuffer size. This may lead to less power savings than a non-reduced-size. Try to increase stolen memory size if available in BIOS.
random:~$ dmesg | grep -c "Reducing the compressed"
47
This patch makes it DRM_INFO_ONCE() just like the similar message
farther down in that function is pr_info_once().
Cc: stable@vger.kernel.org
Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1745
Link: https://patchwork.freedesktop.org/patch/msgid/20180706190424.29194-1-pjones@redhat.com
[vsyrjala: Rebase due to per-device logging]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Looks like I accidentally made it so you couldn't force DPCD backlight
support on, whoops. Fix that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 17f5d57915 ("drm/i915: Force DPCD backlight mode on X1 Extreme 2nd Gen 4K AMOLED panel")
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413214407.1851002-1-lyude@redhat.com
We have some module unload/reload tests hitting an issue with i915
unbinding the component interface before the audio driver has properly
put the power. Log an error about it for ease of debugging. (Normally
this leads to a wakeref debug splat on the power well.)
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417065132.23048-1-jani.nikula@intel.com
The variable test_result is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417160829.112776-1-colin.king@canonical.com
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e20 ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
This is a expected timeout of static TC ports not conneceted, so
not throwing warnings that would taint CI.
v3:
- moved checks to tc_phy_aux_timeout_expected()
v4:
- moved and add comments to tc_phy_aux_timeout_expected()
v5:
- only checking tc_legacy_port for TC ports
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-8-jose.souza@intel.com
As described in "drm/i915/tc/icl: Implement TC cold sequences" users
of TC functions should held aux power well during access to avoid
read garbage due HW in TC cold state.
v3:
- renamed is_tc_cold_blocked() to assert_tc_cold_blocked()
- restored the removed 0xffffffff checks
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-7-jose.souza@intel.com
TC ports can enter in TCCOLD to save power and is required to request
to PCODE to exit this state before use or read to TC registers.
For TGL there is a new MBOX command to do that with a parameter to ask
PCODE to exit and block TCCOLD entry or unblock TCCOLD entry.
So adding a new power domain to reuse the refcount and only allow
TC cold when all TC ports are not in use.
v2:
- fixed missing case in intel_display_power_domain_str()
- moved tgl_tc_cold_request to intel_display_power.c
- renamed TGL_TC_COLD_OFF to TGL_TC_COLD_OFF_POWER_DOMAINS
- added all TC and TBT aux power domains to
TGL_TC_COLD_OFF_POWER_DOMAINS
v3:
- added one msec sleep when PCODE returns -EAGAIN
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
v4:
- Made failure to block or unblock TC cold a error
- removed 5msec timeout, instead giving PCODE 1msec by up 3 times to
recover from the internal error
v5:
- only sleeping 1msec when ret is -EAGAIN
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-6-jose.souza@intel.com
As part of ICL TC cold exit sequences we need to request aux power
well before lock the access to TC ports, so skiping the
intel_tc_port_ref_held() check for TC legacy ports.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-5-jose.souza@intel.com
This is required for legacy/static TC ports as IOM is not aware of
the connection and will not trigger the TC cold exit.
Just request PCODE to exit TCCOLD is not enough as it could enter
again before driver makes use of the port, to prevent it BSpec states
that aux powerwell should be held.
So here embedding the TC cold exit sequence into ICL aux enable,
it will enable aux and then request TC cold to exit.
The TC cold block(exit and aux hold) and unblock was added to some
exported TC functions for the others and to access PHY registers,
callers should enable and keep aux powerwell enabled during access.
Also adding TC cold check and warnig in tc_port_load_fia_params() as
at this point of the driver initialization we can't request power
wells, if we get this warning we will need to figure out how to handle
it.
v2:
- moved ICL TC cold exit function to intel_display_power
- using dig_port->tc_legacy_port to only execute sequences for legacy
ports, hopefully VBTs will have this right
- fixed check to call _hsw_power_well_continue_enable()
- calling _hsw_power_well_continue_enable() unconditionally in
icl_tc_phy_aux_power_well_enable(), if needed we will surpress timeout
warnings of TC legacy ports
- only blocking TC cold around fia access
v3:
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
returning -EAGAIN in in icl_tc_cold_exit()
- removed leftover tc_cold_wakeref
- added one msec sleep when PCODE returns -EAGAIN
v4:
- removed 5msec timeout, instead giving 1msec to whoever is using
PCODE to finish it up to 3 times
- added a comment about turn TC cold exit failure as a error in future
BSpec: 21750
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1296
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-4-jose.souza@intel.com
This is a preparation for ICL TC cold exit sequences.
v2:
- renamed new functions to hsw_power_well_enable_prepare()/complete()
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-3-jose.souza@intel.com
This is a similar function to intel_aux_power_domain() but it do not
care about TBT ports, this will be needed by ICL TC sequences.
v2:
- renamed to intel_legacy_aux_to_power_domain()
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-2-jose.souza@intel.com
Moving the code to return the digital port of the aux channel also
removing the intel_phy_is_tc() to make it generic.
digital_port will be needed in icl_tc_phy_aux_power_well_enable()
so adding it as a parameter to icl_tc_port_assert_ref_held().
While at at removing the duplicated call to icl_tc_phy_aux_ch() in
icl_tc_port_assert_ref_held().
v2:
- fixed build when DRM_I915_DEBUG_RUNTIME_PM is not set
- moved to before hsw_wait_for_power_well_enable() as it will be
needed by hsw_wait_for_power_well_enable() in a future patch
v4:
- fixed action of if (!dig_port), continue instead of return
Cc: You-Sheng Yang <vicamo@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-1-jose.souza@intel.com
Lets have a unified way to handle SAGV changes,
espoecially considering the upcoming Gen12 changes.
Current "standard" way of doing this in commit_tail
is pre/post plane updates, when everything which
has to be forbidden and not supported in new config
has to be restricted before update and relaxed after
plane update.
v2: - Removed unneeded returns(Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415143911.10244-5-stanislav.lisovskiy@intel.com
Add correspondent helpers to be able to get old/new bandwidth
global state object.
v2: - Fixed typo in function call
v3: - Changed new functions naming to use convention proposed
by Jani Nikula, i.e intel_bw_* in intel_bw.c file.
v4: - Change function naming back to intel_atomic* pattern,
was decided to rename in a separate patch series.
v5: - Fix function naming to match existing practices(Ville)
v6: - Removed spurious whitespace
v7: - Removed bw_state NULL checks(Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415143911.10244-3-stanislav.lisovskiy@intel.com
For certain DP VDSC bpp settings, hblank asserts before hblank_early,
leading to a bad audio state. Driver need to program "hblank early
enable" and "samples per line" parameters in AUDIO_CONFIG_BE
register.
This is Display Audio WA #1406928334 for 4k+VDSC usecase
applicable on DP encoders. Implemented the same.
v2: Fixed build failures on 32bit machine.
v3: Dropped u64, added helpers for sample room calculation,
other general comments as per Jani Nikula's feedback.
Also fixed connector type check (spotted by Anshuman)
v4: Addressed Jani Nikula and Kai's review comments.
v5: Addressed Anshuman's review comment and used crtc_* variable
to get timings.
v6: Dropped a redundant initialization.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416105419.9664-1-uma.shankar@intel.com
It requires a separate debugfs attribute to expose lpsp
status to user space, as there may be display less configuration
without any valid connected output, those configuration will not be
able to test lpsp status, if lpsp status exposed from a connector
based debugfs attribute.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-5-anshuman.gupta@intel.com
Add connector debugfs attributes for each intel
connector which is getting register.
v2:
- adding connector debugfs for each connector in
intel_connector_register() to fix CI failure for legacy connectors.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-4-anshuman.gupta@intel.com
New i915_pm_lpsp igt solution approach relies on connector specific
debugfs attribute i915_lpsp_capability, it exposes whether an output is
capable of driving lpsp.
v2:
- CI fixup.
v3:
- register i915_lpsp_info only for supported connector. [Jani]
- use intel_display_power_well_is_enabled() instead of looking
inside power_well count. [Jani]
- fixes the lpsp capable conditional logic. [Jani]
- combined the lpsp capable and enable info. [Jani]
v4:
- Separate out connector based debugfs i915_lpsp_capability
lpsp enable status would be exposes by different entry. [Animesh]
v5:
- Add Platform Gen condition to add i915_lpsp_capability
and some cosmetic nitpick changes. [Animesh]
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-3-anshuman.gupta@intel.com
Gen11 onwards PG3 is contains functions for pipe B,
external displays, and VGA. It make sense to add
a power well id with name ICL_DISP_PW_3 rather then
TGL_DISP_PW_3, Also PG3 power well id requires to
know if lpsp is enabled.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-2-anshuman.gupta@intel.com
As on ICL, we want to use the Type-C aux handlers for the TBT aux wells
to ensure the DP_AUX_CH_CTL_TBT_IO flag is set properly.
Fixes: 656409bbaf ("drm/i915/tgl: Add power well support")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The check was always succeeding even in case of a mismatch due to the
HDCP_STATUS_ENC bit being set. Make sure both bits are actually set.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Fixes: 2320175feb ("drm/i915: Implement HDCP for HDMI")
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328104100.12162-1-oliver.barta@aptiv.com
PLANE_CTL_FORMAT_AYUV is already supported, according to hardware
specification.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200407215546.5445-2-bob.j.paauwe@intel.com
Media decompression support should not be advertised on any display
planes for steppings A0-C0.
Bspec: 53273
Fixes: 2dfbf9d287 ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414211118.2787489-3-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Replace the TGL/ICL specific platform checks with a more generic check
using INTEL_GEN(). Fixes bug with broken audio after S3 resume on JSL
platforms.
An initial version of state save and restore of AUD_FREQ_CNTRL register
was added for subset of platforms in commit 87c1694533
("drm/i915: save AUD_FREQ_CNTRL state at audio domain suspend"). The state
save has proven to work well and it is needed in newer platforms, so needs
to be extended. Although the logic is not in practise needed on GEN9/10
systems, follow the hardware specification and apply state and restore on
all gen9+ platforms.
Bspec: 49281
Link: https://github.com/thesofproject/linux/issues/1719
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330144421.11632-1-kai.vehmanen@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJej453AAoJEAx081l5xIa+r7YQAIX48cUROehoNDhzEHnAxJuU
WZXNHKaMCaDPzAs6SyCtHiPFWH6trBR5McE2dXfg6qc33lnzROFNp5PLB7qb4O+q
+3QkJ5cGd1bohT7vn3omP9FxxZeD4H4bE/zat+yUPwMWJYSUz4m6w6Ya0rIPa8HS
d9nRL0Y6wGBhm8/E0WCB6fe5G96D1JOFGLhfbVajGlDW/I+eBiS5WEyrtlIW698K
Q7lTNOXKEi9kFEZiW39RbKwW3YwqOEiQf1k0KbvUqctq4qLskHD3MgJpmkAiGVPH
mSnTYPPyATILVGKcmEHR3oB9wuYsoPhNgGCVhhm1MppI8GVUzfk6uqOfdK8UNfDU
IRAZ05AynmMMFNu/4Fw0SyR1sbj4OtAiG0hWaJ6Ou9MBzhERGXfT3+/BzeHsR4MJ
+fVIbOArSCAeFTAkqcLVbMKjivAJjullpsj36DFn+lXmHnxB98zAkSNT5dQcDjzl
bp6FhJXm7pWYx8SvkGRneESqLdr2WVgyZmP6u+kgzZ5pPubWSDqY1IFu1exb5Sne
bf7HoPzQ6LyD5KgX5WdoJ5++bcvQ9G4/qDF96NY6emCMKcwnOaAzvtErxQLpFeWP
dZwnxHXXtxY4Z4r5bFURPeWX3rWX5f/cCZ8B7mTUDSTa4hgzV8yUX3ZQBc+9Knja
zuvnpm4j1BXFqOg0Xfsu
=ZTAf
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"As expected, more fixes did turn up in the latter part of the week.
The drm_local_map build regression fix is here, along with temporary
disabling of the hugepage work due to some amdgpu related crashes.
Otherwise it's just a bunch of i915, and amdgpu fixes.
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create"
* tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/ttm: Temporarily disable the huge_fault() callback
drm/bridge: analogix_dp: Split bind() into probe() and real bind()
drm/legacy: Fix type for drm_local_map.offset
drm/amdgpu/display: fix warning when compiling without debugfs
drm/amdgpu: unify fw_write_wait for new gfx9 asics
drm/amd/powerplay: error out on forcing clock setting not supported
drm/amdgpu: fix gfx hang during suspend with video playback (v2)
drm/amd/display: Check for null fclk voltage when parsing clock table
drm/amd/display: Acknowledge wm_optimized_required
drm/amd/display: Make cursor source translation adjustment optional
drm/amd/display: Calculate scaling ratios on every medium/full update
drm/amd/display: Program viewport when source pos changes for DCN20 hw seq
drm/amd/display: Fix incorrect cursor pos on scaled primary plane
drm/amd/display: change default pipe_split policy for DCN1
drm/amd/display: Translate cursor position by source rect
drm/amd/display: Update stream adjust in dc_stream_adjust_vmin_vmax
drm/amd/display: Avoid create MST prop after registration
drm/amdgpu/psp: dont warn on missing optional TA's
drm/amdgpu: update RAS related dmesg print
drm/amdgpu: resolve mGPU RAS query instability
...
This patch process phy compliance request by programming requested
vswing, pre-emphasis and test pattern.
v1: Initial patch.
v2: Fixes added during testing with test-scope. (Khaled/Clint/Manasi)
- pipe used as argument during registers programming instead of port.
- TRANS_CONF must be disable/enable as well during ddi disable/enable.
- harcoded PLTPAT 80 bit custom pattern as the DPR-100 does not set it
in the sink’s DPCDs
- TRANS_DDI_FUNC_CTL DDI_Select (Bits 27:30) need to reset/set during
disable/enable.
v3: used macros instead of numbers and some cosmetic changes. [Manasi]
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-8-animesh.manna@intel.com
These debugfs entry will help testapp to understand the test request
during dp phy compliance mode.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-6-animesh.manna@intel.com
During DP phy compliance auto test mode, sink will request
combination of different test pattern with differnt level of
vswing, pre-emphasis. Function added to prepare for it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-5-animesh.manna@intel.com
vswing/pre-emphasis adjustment calculation is needed in processing
of auto phy compliance request other than link training, so have
made non-static function.
No functional change.
v1: initial patch.
v2:
- used "intel_dp" prefix in function name. (Jani)
- used array notation instead pointer for link_status. (Ville)
v3: Scrapped the initial patch, modified commit description accordingly.
- made non-static function and used intel_dp prefix. (Jani, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-4-animesh.manna@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-8-jani.nikula@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-7-jani.nikula@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-5-jani.nikula@intel.com
Drive-by fix I noticed the other day - drm_dp_mst_has_audio() only ever
made sense back when we still had to validate ports before accessing
them in order to (attempt to) avoid NULL dereferences. Since we have
proper reference counting that guarantees we always can safely access
the MST port, there's no use in keeping this function around as all it
does is validate the port pointer before checking the audio status.
Note - drm_dp_mst_port->has_audio is technically protected by
drm_device->mode_config.connection_mutex, since it's only ever updated
from drm_dp_mst_get_edid(). Additionally, we change the declaration for
port in struct intel_connector to be properly typed, so we can directly
access it.
Changes since v1:
* Change type of intel_connector->port in a separate patch - Sean Paul
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406200646.1263435-2-lyude@redhat.com
The only reason for having this cast as void * before was because we
originally needed to use drm_dp_mst_get_port_validated() and friends in
order to (attempt to) safely access MST ports. However, we've since
improved how reference counting works with ports and mstbs such that we
can now rely on drm_dp_mst_port structs remaining in memory for as long
as the driver needs. This means we don't really need to cast this as
void* anymore, and can just access the struct directly.
We'll also need this for the next commit, so that we can remove
drm_dp_mst_port_has_audio().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406200646.1263435-1-lyude@redhat.com
DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
(cherry picked from commit 70988115ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
(cherry picked from commit f77a2db27f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On TypeC ports if a sink deasserts/reasserts its HPD signal, generating
a hotplug interrupt without the sink getting unplugged/replugged from
the connector, there can be an up to 3 seconds delay until the AUX
channel gets functional. To avoid detection failures this delay causes
retry the detection for 5 seconds.
I noticed this on ICL/TGL RVPs and a DELL XPS 13 7390 ICL laptop.
References: https://gitlab.freedesktop.org/drm/intel/issues/1067
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-2-imre.deak@intel.com
On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com
Move the final DP_TP_CTL frobbing of port sync to the master
encoder's enable hook. Now neatly out of sight from the high level
modeset code.
And thus we've eliminated all the special casing of port sync
in the high level modeset code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-14-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently only port sync pipes do the sequence such that
we first do the modeset part for every pipe and then do
the plane/etc. updates. Let's follow that apporach for
all pipes in skl+ so that we can properly integrate the
port sync into the normal modeset flow.
v2: Remove now stale TODO of port sync slave entries[]
s/oldnew/new/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-12-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Don't assume there is just one port sync slave. We might have several.
v2: Fix unitialized new_crtc_state usage (José)
Fix clearing of modeset_pipes for slaves
s/oldnew/new/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Transcoder port sync was introduced to the hardware in BDW. We
can trivially enable it for SKL+ since the same codepaths are
already used for ICL+ port sync. The only difference is the actual
location of the bits we need to poke.
We leave BDW out (at least for now) since it uses different modeset
paths that haven't been adapted for port sync, and IIRC using the
feature would involve some extra workarounds we've not implemented.
Pre-BDW hardware does not support port sync so we'd have to tweak
the modeset sequence to start the pipes as close together as possible
and hope for the best. So far no one has seriously tried to implement
that.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/27
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-9-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
We have a bunch of code that would like to know which
CPU transcoders are actually present in the hardware. Rather than
use various ad-hoc methods let's just include a full bitmask in
the device info, alongside pipe_mask.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318170235.15176-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
-----BEGIN PGP SIGNATURE-----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=I0vz
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 5.7-rc1.
Highlights:
- i915 enables Tigerlake by default
- i915 and amdgpu have initial OLED backlight support
[ Jani Nikula pipes up and points out that we've had a bunch of
"initial support" code for a long time already, but only now
Lyude made it actually work on real world machines ]
- vmwgfx add support to enable OpenGL 4 userspace
- zero length arrays are mostly removed.
Detailed summary:
new driver:
- tidss: TI Keystone platform display subsystem
core:
- new drm device warn macros
- mode config valid for memory constrained devices
- bridge bus format negotation
- consolidated fake vblank event handling
- dma_alloc related cleanups
- drop get_crtc callback
- dp: DP1.4 EDID corruption test
- EDID CEA detailed timings improvements
- relicense some code to dual GPL2/MIT
- convert core vblank support to per-crtc support
- rework drm_global_mutex
- bridge rework to allow omap_dss custom driver removeal
- remove drm_fb_helper connector interrfaces
- zero-length array removal
scheduler:
- support for modifying the sched list
- revert job distribution optimization
- helper to pick least loaded scheduler
- race condition fix
mst:
- various fixes
- remove register_connector callback
i915:
- uapi to allows userspace specific CS ring buffer sizes
- Tigerlake enablement patches + Tigerlake enabled by default
- new sysfs entries for engine properties
- display/logging refactors
- eDP/DP fixes for DPCD
- Gen7 back to aliasing-ppgtt
- Gen8+ irq refactor
- Avoid globals
- GEM locking fixes and simplifications
- Ice Lake and Elkhart Lake fixes and workarounds
- Baytrail/Haswell instability fix
- GVT - VFIO edid better support
amdgpu:
- Rework VM update handling in preparation for HMM support
- drm load/unload removal fixups
- USB-C PD firmware updates
- HDCP srm support
- Navi/renoir PM watermark fixes
- OLED panel support
- Optimize debugging vram access
- Use BACO for runtime pm
- DC clock programming optimizations and fixes
- PSP fw loading sequence updates
- Drop DRIVER_USE_AGP
- Remove legacy drm load and unload callbacks
- ACP Kconfig fix
- Lots of fixes across the driver
amdkfd:
- runtime pm support
- more gfx config details in amdgpu
radeon:
- drop DRIVER_USE_AGP
vmwgfx:
- Disable DMA when SEV encryption in use
- Shader Model 5 support - needed for GL4 support
msm:
- DPU resource manager refactor
- dpu using atomic global state
mediatek:
- MT8183 DPI support
etnaviv:
- out-of-bounds read fix
- expose feature flags for GC400 STM32MP1 SoC
- runtime suspend entry fix
- dma32 zone fix
hisilicon:
- mode selection fixes
meson:
- YUV420 support
lima:
- add support for heap buffers
tinydrm:
- removal of owner field
- explicit DT dependency removal
- YAML schema conversion
tegra:
- misc cleanups
tidss:
- new driver
virtio:
- better batching of notifications to host
- memory handling reworked
- shmem + gpu context fixes
hibmc:
- add gamma_set support
- improve DPMS support
pl111:
- Integrator IM-PD1 support
sun4i:
- LVDS support for A20 + A33
- DSI panel handling improvements"
* tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm: (1537 commits)
drm/i915/display: Fix mode private_flags comparison at atomic_check
drm/i915/gt: Stage the transfer of the virtual breadcrumb
drm/i915/gt: Select the deepest available parking mode for rc6
drm/i915: Avoid live-lock with i915_vma_parked()
drm/i915/gt: Treat idling as a RPS downclock event
drm/i915/gt: Cancel a hung context if already closed
drm/i915: Use explicit flag to mark unreachable intel_context
drm/amdgpu: don't try to reserve training bo for sriov (v2)
drm/amdgpu/smu11: add support for SMU AC/DC interrupts
drm/amdgpu/swSMU: handle manual AC/DC notifications
drm/amdgpu/swSMU: handle DC controlled by GPIO for navi1x
drm/amdgpu/swSMU: set AC/DC mode based on the current system state (v2)
drm/amdgpu/swSMU: correct the bootup power source for Navi1X (v2)
drm/amdgpu/swSMU: use the smu11 power source helper for navi1x
drm/amdgpu/smu11: add a helper to set the power source
drm/amd/swSMU: add callback to set AC/DC power source (v2)
drm/scheduler: fix rare NULL ptr race
drm/amdgpu: fix the coverage issue to clear ArcVPGRs
drm/amd/display: Fix pageflip event race condition for DCN.
drm/[radeon|amdgpu]: Remove HAINAN board from max_sclk override check
...
Specification was updated with vswing tables for different
configurations.
Also reordering icl_mg_phy_ddi_buf_trans struct to match table order.
BSpec: 21735
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-3-jose.souza@intel.com
DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
Use the recently introduced encoder .compute_config_late() hook to
do the MST master transcoder assignment. Avoids having to do it
in a funny way before we know the CPU transcoder of each pipe.
And now we can also properly use hw.active instead of uapi.active
since it too has been calculated earlier for everyone.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Not sure why this thing is trying to avoid declaring the proper
type for these pointers. But since these are used only once let's
just get rid of the local variable entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310202752.28454-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Commit 632f3ab95f ("drm/i915/audio: add codec wakeup override
enabled/disable callback"), added logic to toggle Codec Wake on gen9.
This is used by audio driver when it resets the HDA controller.
It seems explicit toggling of the wakeline can help to fix problems
with probe failing on some gen12 platforms. And based on specs, there
is no reason why this programming sequence should not be applied to all
gen9+ platforms. No side-effects are seen on gen10/11. So apply
the wake-logic to all gen9+ platforms.
Link: https://github.com/thesofproject/linux/issues/1847
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200324153212.6303-1-kai.vehmanen@linux.intel.com
This patch fixes the private_flags of mode to be checked and
compared against uapi.mode and not from hw.mode. This helps
properly trigger modeset at boot if desired by driver.
It helps resolve audio_codec initialization issues if display
is connected at boot. Initial discussion on this issue has happened
on below thread:
https://patchwork.freedesktop.org/series/74828/
v2: No functional change. Fixed the Closes tag and added
Maarten's RB.
v3: Added Fixes tag.
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Souza, Jose <jose.souza@intel.com>
Fixes: 58d124ea27 ("drm/i915: Complete crtc hw/uapi split, v6.")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1363
Suggested-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: SweeAun Khor <swee.aun.khor@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200326125111.11081-1-uma.shankar@intel.com
(cherry picked from commit d5e5670592)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch fixes the private_flags of mode to be checked and
compared against uapi.mode and not from hw.mode. This helps
properly trigger modeset at boot if desired by driver.
It helps resolve audio_codec initialization issues if display
is connected at boot. Initial discussion on this issue has happened
on below thread:
https://patchwork.freedesktop.org/series/74828/
v2: No functional change. Fixed the Closes tag and added
Maarten's RB.
v3: Added Fixes tag.
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Souza, Jose <jose.souza@intel.com>
Fixes: 58d124ea27 ("drm/i915: Complete crtc hw/uapi split, v6.")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1363
Suggested-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: SweeAun Khor <swee.aun.khor@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200326125111.11081-1-uma.shankar@intel.com
Avoid using the uninitialised len along the impossible error path to
shut the compiler up:
drivers/gpu/drm/i915/display/intel_dp.c:4928 intel_write_dp_sdp() error: uninitialized symbol 'len'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325140754.12636-1-chris@chris-wilson.co.uk
We've migrated all the heavy users over to the intel_gt, and can finally
drop the last few users and with that the mirror in dev_priv->engine[].
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325234803.6175-1-chris@chris-wilson.co.uk
dGFX has local memory so it does not have aperture or support
CPU fences but even for iGFX it have a small number of fences.
As replacement for fences to track frontbuffer modifications by CPU
we have a software tracking that is already in used by FBC and PSR.
PSR don't support fences so it shows that this tracking is reliable.
So lets make fences a nice-to-have to activate FBC for GEN9+, this
will allow us to enable FBC for dGFXs and iGFXs even when there is no
available fence.
We do not set fences to rotated planes but FBC only have restrictions
against 16bpp, so adding it here.
Also adding a new check for the tiling format, fences are only set
to X and Y tiled planes but again FBC don't have any restrictions
against tiling so adding linear as supported as well, other formats
should be added after tested but IGT only supports drawing in thse
3 formats.
intel_fbc_hw_tracking_covers_screen() maybe can also have the same
treatment as fences but BSpec is not clear if the size limitation is
for hardware tracking or general use of FBC and I don't have a 5K
display to test it, so keeping as is for safety.
v2:
- Added tiling and pixel format rotation checks
- Changed the GEN version not requiring fences to 11 from 9, DDX
needs some changes but it don't have support for GEN11+
v3:
- Changed back to GEN9+
- Moved GEN test to inside of tiling_is_valid()
v4:
- moved rotation check to its own functions
v5:
- renamed rotations_is_valid to rotation_is_valid
- moved pre-g4x rotation check to rotation_is_valid()
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200319211535.114625-1-jose.souza@intel.com
On dsi cmd mode we do not receive vblanks instead
we would get TE and these flags indicate TE is expected on
which port.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-6-vandita.kulkarni@intel.com
If the GOP has programmed periodic command mode,
we need to disable that which would need a
deconfigure and configure sequence.
v2: Fix sparse error, pass only intel_dsi (Jani)
v3: Use intel_de_read
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-5-vandita.kulkarni@intel.com
Adding TE flags and periodic command mode flags
as part of private flags to indicate what TE interrupts
we would be getting instead of vblanks in case of mipi dsi
command mode.
v2: Add TE flag description (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-4-vandita.kulkarni@intel.com
Transcoder timing calculation differ for command mode.
v2: Use is_vid_mode, and use same I915_WRITE (Jani)
v3: Adjust the calculations to reflect dsc compression ratio
v4: Rearrange the vertical and horizontal timing calc, optimize
local variables usage. (Jani)
v5: Fix the values used for calculation, use afe_clk for
byte clock calculation, use intel_de_write/read (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-3-vandita.kulkarni@intel.com
Configure the transcoder to operate in TE GATE command mode
and take TE events from GPIO.
Also disable the periodic command mode, that GOP would have
programmed.
v2: Disable util pin (Jani)
v3: Use intel_de_write (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-2-vandita.kulkarni@intel.com
Few edp panels like Sharp is triggering short and long
hpd pulse after panel is getting powered off.
Currently driver is already ignoring long pulse for eDP
panel but in order to process the short pulse, it turns on
the VDD which requires panel power_cycle_delay + panel_power_on_delay
these delay on Sharp panel introduced the responsiveness overhead
of 800ms in the modeset sequence and as well is in suspend
sequence.
Ignoring any short pulse if panel is powered off.
FIXME: It requires to wait for panel_power_off delay in order
to check the panel power status due to pps_lock because panel triggers
short pulse immediately after writing PP_OFF to PP_CTRL register and
wait_panel_off waits for panel_power_off delay with pps_lock held.
This still creates responsiveness overhead of panel_power_off delay.
v2:
- checking vdd along with panel power to ignore the hpd. [Jani,Ville]
v3:
- safer side check to ignore the long hpd when eDP have power,
adding type of hpd to debug log. [Jani]
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318081837.23983-1-anshuman.gupta@intel.com
We only consider crtc_state->enable when initially calculating plane
visibility. Later on we try to override the plane's state to invisible
if the crtc is in DPMS off state (crtc_state->active==false).
Unfortunately the code doing that only updates the plane_state.visible
flag and the crtc_state.active_planes bimask, but forgets to update
some of the other plane bitmasks stored in the crtc_state. Namely
crtc_state.nv12_planes is left set up based on the original visibility
check which makes icl_check_nv12_planes() pick a slave plane for the
flagged plane in the bitmask. Later on we hit the watermark code
which sees a plane with a slave assigned and it then makes the
logical assumption that the master plane must itself be visible.
Since the master's plane_state.visible flag was already cleared
we get a WARN.
Fix the problem by clearing all the plane bitmasks for DPMS off.
This is more or less the wrong approach and instead we should
calculate all the plane related state purely based crtc_state->enable
(to guarantee that the subsequent DPMS on can't fail). However in
the past we definitely had some roadblocks to making that happen.
Not sure how many are left these days, but let's stick to the current
approach since it's a much simpler fix to the immediate problem
(the WARN).
v2: Keep the visible=false, it's important (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318174515.31637-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
It adds routines that write DP VSC SDP and DP HDR Metadata Infoframe SDP.
In order to pack DP VSC SDP, it adds intel_dp_vsc_sdp_pack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to pack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_pack() function.
And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A mechanism and a naming rule of intel_dp_set_infoframes() function
references intel_encoder->set_infoframes() of intel_hdmi.c .
VSC SDP is used for PSR and Pixel Encoding and Colorimetry Formats cases.
Because PSR routine has its own routine of writing a VSC SDP, when the PSR
is enabled, intel_dp_set_infoframes() does not write a VSC SDP.
v3:
- Explicitly disable unused DIPs (AVI, GCP, VS, SPD, DRM. They will be
used for HDMI), when intel_dp_set_infoframes() function will be called.
- Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp.
v4: Use struct drm_device logging macros
v5:
- use intel_de_*() functions for register access
- Addressed review comments from Uma
Polish commit message and comments
Add 6bpc to packing of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-5-gwan-gyeong.mun@intel.com
It stores computed dp hdr metadata infoframe sdp to infoframes.drm of
crtc state. It referenced intel_hdmi_compute_drm_infoframe().
While computing, we'll also fill out the infoframes.enable bitmask
appropriately.
v2: Wrap a long line.
v4: Use struct drm_device logging macros
v5: Fix typo [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-4-gwan-gyeong.mun@intel.com
In order to support state readout for DP VSC SDP, we need to have a
structure which holds DP VSC SDP payload data such as
"union hdmi_infoframe drm" which is used for DRM infoframe.
It adds a struct drm_dp_vsc_sdp vsc to intel_crtc_state.infoframes.
And it stores computed dp vsc sdp to infoframes.vsc of crtc state.
While computing we'll also fill out the inforames.enable bitmask
appropriately.
The compute routine follows DP 1.4 spec [Table 2-117: VSC SDP Payload for
DB16 through DB18].
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v5:
- Rebased
- Add warning where a bpc is 6 and a pixel format is RGB.
v7: Fix the wrong check of combination bpc 6 and RGB pixelformat
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-3-gwan-gyeong.mun@intel.com
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAl5sIZ0ACgkQ+mJfZA7r
E8o1LQf+L/Vpm46QQGEyzHINf/gTQvFvumuNAX352vEHaKUgLtTuI7xfpd0c83G1
5VI+L0Q/ARvakkgfZuHYInlxc9azkcPF1wXb3bLqkoiJ15ydwx5GWjVpZ8uFT+fG
xzaHBqhqUcvw/kXI1Cy5kIDAlFO9rKLsoLS2qQF9BsYHyxa52ok9/hW+lM7C+vfR
aYvEr7aAK0o06mqgwc3DHXGuzaS1S9kxtvj9ZkHNsD9iwD4rrEIvW3BPuDqEVkGq
TkKfThhzJp2FDjXkgCQbLm2BQmxBS0aihwNsQ/lDUUAxcFiuRYwMSoT63vPD1OYI
lgG0BuJkwK7csJIMrnOs/ZAMeKyTQA==
=vrB8
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2020-03-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200314001535.GA2969344@intel.com
This fixes a problem found on the MacBookPro 2017 Retina panel.
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec = multiplier 0xc),
but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to add the additiional 324000 kbps link rate during
edp setup.
Link to previous discussion of a different attempted fix
with Ville and Jani:
https://patchwork.kernel.org/patch/11325935/
v2: Follow Jani's proposal of defining quirk_rates[] instead
of just appending 324000. This for better clarity.
v3: Rebased onto current drm-tip, as of 16-March-2020. Adapt
to new edid_quirks parameter of drm_dp_has_quirk().
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316042340.4783-1-mario.kleiner.de@gmail.com
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hdcp.c.
This also involves extracting the drm_i915_private device from the
intel_connector type for use in the macros.
v2 by Jani:
- rebase
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47d5e88dedc08ee48938344296ada550dedd5f90.1583766715.git.jani.nikula@intel.com
Convert various instances of printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_fbdev.c.
This also involves extracting the drm_i915_private device from various
intel types.
v2 by Jani:
- fix the final one too
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7081a49d20cc46b1b1144c83a4e21294d121d8a7.1583766715.git.jani.nikula@intel.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of debugfs_init() functions and have the functions return
void.
v2: convert intel_display_debugfs_register() stub to return void too.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-15-wambui.karugax@gmail.com
For icl+, have hw read out to create hw blob of gamma
lut values. icl+ platforms supports multi segmented gamma
mode by default, add hw lut creation for this mode.
This will be used to validate gamma programming using dsb
(display state buffer) which is a tgl specific feature.
v2: -readout code for multisegmented gamma has to come
up with some intermediate entries that aren't preserved
in hardware (Jani N)
-linear interpolation (Ville)
-moved common code to check gamma_enable to specific funcs,
since icl doesn't support that
v3: -use u16 instead of __u16 [Jani N]
-used single lut [Jani N]
-improved and more readable for loops [Jani N]
-read values directly to actual locations and then fill gaps [Jani N]
-moved cleaning to patch 1 [Jani N]
-renamed icl_read_lut_multi_seg() to icl_read_lut_multi_segment to
make it similar to icl_load_luts()
-renamed icl_compute_interpolated_gamma_blob() to
icl_compute_interpolated_gamma_lut_values() more sensible, I guess
v4: -removed interpolated func for creating gamma lut values
-removed readouts of fine and coarse segments, failure to read PAL_PREC_DATA
correctly
v5: -added gamma_enable check inside read_luts()
v6: -renamed intel_color_lut_entry_equal() to intel_color_lut_entries_equal() [Ville]
-changed if-else to switch [Ville]
-removed intel_color_lut_entry_multi_equal() [Ville]
v7: -checkpatch warnings
v8: -rebased
v9: -rebased, aligned with Ville's style of gamma cleanup
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317135736.14305-1-swati2.sharma@intel.com
drm_dp_mst_topology_mgr_cbs.destroy_connector callbacks are identical
amongst every driver and don't do anything other than cleaning up the
connector((drm_connector_unregister()/drm_connector_put())) except for
amdgpu_dm driver where some amdgpu_dm specific code in there.
This connector cleaning up is now being handled in the drm core so
driver destroy_connector callbacks are not needed (except for
amdgpu_dm) hence remove them.
Removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .destroy_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-6-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_port_add_connector() directly calls the
drm_connector_register() now and
drm_dp_mst_topology_mgr_cbs.register_connector callback is not getting
called anymore.
Hence remove all drm_dp_mst_topology_mgr_cbs.register_connector
callbacks.
This is the preparatory step for removing the
drm_dp_mst_topology_mgr_cbs.register_connector callback hook.
The removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .register_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-3-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Gen12 hardware supports HDMI audio pixel clocks of 296.7/297Mhz
and 593.4/594Mhz. Add the missing rates and add logic to ignore
them if running on older hardware.
Bspec: 49333
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310162338.9387-1-kai.vehmanen@linux.intel.com
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hotplug.c.
In some cases, this involves extracting the drm_i915_private pointer from
the drm_device struct to be used in the logging macros.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3dfda89ab4a234f299ada77abd14163cef3f8bd4.1583766715.git.jani.nikula@intel.com
Platforms without fences don't have FBC host tracking and those
registers are marked as reserved in those platforms.
v2: checking num_fences to write to FBC fence registers (Ville)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306185833.53984-2-jose.souza@intel.com
i915 can enable aux device nodes for DP MST by calling
drm_dp_mst_connector_late_register()/
drm_dp_mst_connector_early_unregister(),
so let's hook that up.
Changes since v1:
* Call intel_connector_register/unregister() from
intel_dp_mst_connector_late_register/unregister() so we don't lose
error injection - Ville Syrjälä
Changes since v2:
* Don't forget to clean up if intel_connector_register() fails - Ville
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310195122.1590925-1-lyude@redhat.com
gmbus/aux may be clocked by cdclk, thus we should make sure no
transfers are ongoing while the cdclk frequency is being changed.
We do that by simply grabbing all the gmbus/aux mutexes. No one
else should be holding any more than one of those at a time so
the lock ordering here shouldn't matter.
v2: Use mutex_lock_nest_lock() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302174442.5803-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The low level read_lut() functions don't need the entire crtc state
as they know exactly what they're reading. Just need to pass in the
crtc to get at the pipe. This now neatly mirrors the load_lut()
direction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-10-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
PIPEGCMAX is a 11.6 (or 1.16 if you will) value. Ie. it can
represent a value of 1.0 when the maximum we can store in the
software LUT is 0.ffff. Clamp the value so that it gets
saturated to the max the uapi supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-9-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
A variable called 'i' having an unsigned type is just looking for
trouble, and using a sized type generally makes no sense either.
Change all of them to just plain old int. And do the same for some
'lut_size' variables which generally provide the loop end codition
for 'i'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-7-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Only load the CGM CSC based on the cgm_mode bit like we
do with the gamma/degamma LUTs. And make the function
naming and arguments consistent as well.
TODO: the code to convert the coefficients look totally
bogus. IIRC CHV uses two's complement format but the code
certainly doesn't generate that, so probably negative
coefficients are totally busted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303173313.28117-2-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Fix the following kerneldoc warning and while at it also the doc for the
corresponding vfunc hook.
$ make htmldocs 2>&1 > /dev/null | grep i915
./drivers/gpu/drm/i915/display/intel_dpll_mgr.h:285: warning: Function parameter or member 'get_freq' not described in 'intel_shared_dpll_funcs'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304150918.25473-1-imre.deak@intel.com
On some platforms such as Elkhart Lake, although we may use DDI D
to drive a connector, we have to use PHY A (Combo Phy PORT A) to
detect the hotplug interrupts as per the spec because there is no
one-to-one mapping between DDIs and PHYs. Therefore, use the
function intel_port_to_phy() which contains the logic for such
mapping(s) to find the correct hpd_pin.
This change should not affect other platforms as there is always
a one-to-one mapping between DDIs and PHYs.
v2:
- Convert the case statements to use PHYs instead of PORTs (Jani)
v3:
- Refactor the function to reduce the number of return statements by
lumping all the case statements together except PHY_F which needs
special handling (Jose)
v4:
- Add a comment describing how the HPD pin value associated with any
port can be retrieved using port or phy enum value. (Jani)
v5:
- Use case ranges instead of individual labels and also normalize the
return statement by adding -PHY_A to the expression (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304234240.12062-1-vivek.kasireddy@intel.com
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
drm_fb_helper_{add,remove}_one_connector() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-5-pankaj.laxminarayan.bharadiya@intel.com
The max connector argument for drm_fb_helper_init() isn't used anymore
hence remove it.
All the drm_fb_helper_init() calls are modified with below sementic
patch.
@@
expression E1, E2, E3;
@@
- drm_fb_helper_init(E1,E2, E3)
+ drm_fb_helper_init(E1,E2)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-2-pankaj.laxminarayan.bharadiya@intel.com
Check the edge case where batch_start_offset sits exactly on the batch
size.
v2: add new range_overflows variant to capture the special case where
the size is permitted to be zero, like with batch_len.
v3: other way around. the common case is the exclusive one which should
just be >=, with that we then just need to convert the three odd ball
cases that don't apply to use the new inclusive _end version.
Testcase: igt/gem_exec_params/invalid-batch-start-offset
Fixes: 0b5372727b ("drm/i915/cmdparser: Use cached vmappings")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306094735.258285-1-matthew.auld@intel.com
Converting error to debug print if sink fails to configure scrambling or
TMDS bit clock ratio. In this case, we are timing out while disabling
the scrambling and setting the SCDC ratio, as there is no response
to the I2C SCDC write from the sink device. Error isn't due to something
wrong done from driver side.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302213807.6488-1-swati2.sharma@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The Thundersoft TST178 tablet uses a DSI panel with an external PWM
controller (as all DSI panels do). But unlike other DSI panels a duty-cycle
of 100% turns the backlight off and 0% sets it to maximum brightness.
I've checked the VBT and there is a BDB_LVDS_BACKLIGHT section, but
it does not set the active_low_pwm flag. This tablet re-uses the main
PCI vendor and product ids for the subsystem ids, so I see no other option
then to add a DMI based quirk to fix this.
Note that the PWM backlight code in intel_panel.c currently does not honor
the vbt.active_low_pwm flag, but that does not matter in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-2-hdegoede@redhat.com
Use intel_panel_compute_brightness() from pwm_setup_backlight() so that
we correctly take i915_modparams.invert_brightness and/or
QUIRK_INVERT_BRIGHTNESS into account when setting + getting the initial
brightness value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221172927.510027-1-hdegoede@redhat.com
intel_ddi_clock_get() tests the DPLL ID against DPLL_ID_ICL_TBTPLL (2)
to determine whether to try to descend into a TBT-specific handler.
However this test will also be true when DPLL4 on EHL is used since that
shares the same DPLL ID (2).
Add an extra check to ensure the PHY is actually a Type-C PHY before
descending into the TBT handling. This should ensure EHL still takes
the correct code path and somewhat future-proof the code as well.
v2: Drop the gen+ check since only gen11+ platforms can have Type-C
outputs. (Imre)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1369
Fixes: 45e4728b87 ("drm/i915: Move DPLL frequency calculation to intel_dpll_mgr.c")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303195043.959913-1-matthew.d.roper@intel.com
The X1 Extreme is one of the systems that lies about which backlight
interface that it uses in its VBIOS as PWM backlight controls don't work
at all on this machine. It's possible that this panel could be one of
the infamous ones that can switch between PWM mode and DPCD backlight
control mode, but we haven't gotten any more details on this from Lenovo
just yet. For the time being though, making sure the backlight 'just
works' is a bit more important.
So, add a quirk to force DPCD backlight controls on for these systems
based on EDID (since this panel doesn't appear to fill in the device ID).
Hopefully in the future we'll figure out a better way of probing this.
Changes since v2:
* The bugzilla URL is deprecated, bug reporting happens on gitlab now.
Update the messages we print to reflect this
* Also, take the opportunity to move FDO_BUG_URL out of i915_utils.c and
into i915_utils.h so that other places which print things that aren't
traditional errors but are worth filing bugs about, can actually use
it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303215320.93491-1-lyude@redhat.com
The whole point of using OUIs is so that we can recognize certain
devices and potentially apply quirks for them. Normally this should work
quite well, but there appears to be quite a number of laptop panels out
there that will fill the OUI but not the device ID. As such, for devices
like this I can't imagine it's a very good idea to try relying on OUIs
for applying quirks. As well, some laptop vendors have confirmed to us
that their panels have this exact issue.
So, let's introduce the ability to apply DP quirks based on EDID
identification. We reuse the same quirk bits for OUI-based quirks, so
that callers can simply check all possible quirks using
drm_dp_has_quirk().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-2-lyude@redhat.com
DP shim's config_stream_type considered to be succeeded when
return value of intel_dp_hdcp2_write_msg() equals to size of
message to be written, it makes config_stream_type to return
a zero success value in order to succeed the HDCP auth.
v2:
- config_stream_type() returns 0 on success. [Ram]
CC: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303073838.25871-1-anshuman.gupta@intel.com
HDCP Repeater initializes seq_num_V to 0 at the beginning of
hdcp Session i.e. after AKE_init received, refer
HDCP 2.2 Spec HDMI PAGE 19, DP PAGE 20.
HDCP 2.2 Comp specs 1B-06 test verifies that whether DUT
considers failure of authentication if the repeater provides a
non-zero value in seq_num_V in the first,
RepeaterAuth_Send_ReceiverID_List message.
Make sure that HDCP repeater initializes seq_num_V to zero at
beginning of session i.e. after AKE_Init, fail the Auth if
there is non zero seq_num_V.
v2:
- Used existing hdcp2_encrypted flag instead of
declaring new flag. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200220123217.23635-2-anshuman.gupta@intel.com
It irks me to use crtc_state_is_legacy_gamma() inside the guts
of the CHV color management code. Let's get rid of it and instead
just consult cgm_mode to figure out if we want to enable the pipe
gamma or the CGM gamma.
Also CHV display engine is based on i965/g4x so we should fall back
to the i965 path when the CGM gamma is not used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107151725.10507-3-ville.syrjala@linux.intel.com
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Add intel_vgpu_register() abstraction, rename i915_detect_vgpu() to
intel_vgpu_detect() to match other function naming, un-inline
intel_vgpu_active(), intel_vgpu_has_full_ppgtt() and
intel_vgpu_has_huge_gtt() to reduce header interdependencies.
The i915_vgpu.[ch] filename and intel_vgpu_ prefix discrepancy remains.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227144408.24345-1-jani.nikula@intel.com
has_transcoder() was unused because function which was using it,
intel_display_capture_error_state() defined under
CONFIG_DRM_I915_CAPTURE_ERROR.
Moving has_transcoder() to under CONFIG_DRM_I915_CAPTURE_ERROR.
No functional change.
Fixes: d54c1a513c ("drm/i915: Fix broken transcoder err state")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227175147.11362-1-anshuman.gupta@intel.com
Converts remaining instances of the printk based logging macros in
i915/display/intel_hdcp.c with the struct drm_device based macros
manually.
This is continuation of commit 65833c4638 ("drm/i915/hdcp: conversion
to struct drm_device based logging macros.")
v2:
i915_dev_priv is used instead of drm_device for reusability [JaniN]
v3:
Made it independent from the series.
once instance of dev_priv naming is changed to i915 [Jani N]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212123007.6659-1-ramalingam.c@intel.com
All platforms using the shared DPLL framework use 3 reference clocks for
their DPLLs: SSC, non-SSC and DSI. For a more unified way across
platforms store the frequency of these ref clocks as part of the DPLL
global state. This also allows us to keep the HW access reading out the
ref clock value separate from the DPLL frequency calculation that
depends on the ref clock.
For now add only the SSC and non-SSC ref clocks, as the pre-ICL DSI code
has its own logic for calculating DPLL parameters instead of the shared
DPLL framework.
v2:
- Apply the ICL combo PHY PLL ref_clock/2 adjustment during the
frequency->PLL param conversion direction as well. (CI shards)
- s/kHZ/kHz/ (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228153328.17842-1-imre.deak@intel.com
The types of PLLs used for HDMI/DP on HSW are WRPLL/LCPLL accordingly,
so use these names to align better with the rest of WRPLL/LCPLL function
names elsewhere.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-9-imre.deak@intel.com
For clarity keep the SKL DPLL ref clock in a variable instead of
open-coding it. Store the value in kHZ units as done on other platforms.
This allows us in a later patch to keep track of the DPLL ref clock in a
more unified way across all platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-8-imre.deak@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
For clarity add a new DPLL specific struct to the i915 device struct and
move all DPLL fields into it. Accordingly remove the dpll_ prefixes, as
the new struct already provides the required namespacing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-4-imre.deak@intel.com
There seems to be a bit of confusing redundancy in a way, how
plane data rate/min cdclk are calculated.
In fact both min cdclk, pixel rate and plane data rate are all
part of the same formula as per BSpec.
However currently we have intel_plane_data_rate, which is used
to calculate plane data rate and which is also used in bandwidth
calculations. However for calculating min_cdclk we have another
piece of code, doing almost same calculation, but a bit differently
and in a different place. However as both are actually part of same
formula, probably would be wise to use plane data rate calculations
as a basis anyway, thus avoiding code duplication and possible bugs
related to this.
Another thing is that I've noticed that during min_cdclk calculations
we account for plane scaling, while for plane data rate, we don't.
crtc->pixel_rate seems to account only for pipe ratio, however it is
clearly stated in BSpec that plane data rate also need to account
plane ratio as well.
So what this commit does is:
- Adds a plane ratio calculation to intel_plane_data_rate
- Removes redundant calculations from skl_plane_min_cdclk which is
used for gen9+ and now uses intel_plane_data_rate as a basis from
there as well.
v2: - Don't use 64 division if not needed(Ville Syrjälä)
- Now use intel_plane_pixel_rate as a basis for calculations both
at intel_plane_data_rate and skl_plane_min_cdclk(Ville Syrjälä)
v3: - Again fix the division macro
- Fix plane_pixel_rate to pixel_rate at intel_plane_pixel_rate
callsites
v4: - Renamed skl_plane_ratio function back(Ville Syrjälä)
v5: - Don't precalculate plane pixel rate for invisible plane,
check for visibility first, as in invisible case it will
have dst_w and dst_h equal to zero, causing divide error.
v6: - Removed useless warn in intel_plane_pixel_rate(Ville Syrjälä)
- Fixed alignment in intel_plane_data_rate(Ville Syrjälä)
- Changed pixel_rate type to be unsigned int in
skl_plane_min_cdclk(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227150935.2107-1-stanislav.lisovskiy@intel.com
Supposedly both src coordinates have to even when doing 90/270
degree rotation with RGB565. This is definitely true for the
X coordinate (we just get a black screen when it is odd). My
experiments didn't show any misbehaviour with an odd
Y coordinate, but let's trust the spec and reject that one
as well.
v2: Ignore ccs hsub/vsub
v3: Clarify the CCS special (Maarten)
Deal with tgl+ CCS modifiers where we
do need to look at hsub/vsub
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228160523.1064-1-ville.syrjala@linux.intel.com
Some devices with a builtin panel have the panel mounted upside down,
this is indicated by the rotate_180 bit in the BDB_GENERAL_FEATURES VBT
block.
We store this info in dev_priv->vbt.orientation, use this to set the
connector's orientation property so that fbcon and userspace will show
the image the right way up on devices with an upside-down mounted panel.
This fixes the image being upside-down on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-3-hdegoede@redhat.com
Commit 82daca2975 ("drm/i915: Add "panel orientation" property to the
panel connector, v6.") uses hardware state readback to determine if the
GOP is rotating the image by 180 degrees to compensate for upside-down
mounted panels.
When I wrote that commit I tried to find the VBT bits the GOP used to
decide to rotate the image, but I could not find them. Back then I only
looked at the rotation bits in struct mipi_config and these read 0 on
the 1 BYT device I have with an upside-down mounted panel
(a GP-electronic T701 tablet). While working on a similar problem on a
BYT device with an eDP panel I noticed that the new
intel_dsi_get_panel_orientation() helper which gets used on newer
SoCs (Apollo-Lake, etc.) checks the rotate_180 bit in the
BDB_GENERAL_FEATURES VBT block.
I've checked and this bit indeed is set on the GP-electronic T701 tablet,
so using the generic intel_dsi_get_panel_orientation() helper there does
the right thing without needing any extra readback of hw state.
This commit removes the special handling of the panel orientation for
DSI panels on BYT/CHT devices, bringing the handling in line with the
handling of DSI panels on other devices.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-2-hdegoede@redhat.com
Having an array pipe_crc[I915_MAX_PIPES] in struct drm_i915_private
should be an obvious clue this should be located in struct intel_crtc
instead. Make it so.
As a side-effect, fix some errors in indexing pipe_crc with both pipe
and crtc index. And, of course, reduce the size of i915_drv.h.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227161253.15741-1-jani.nikula@intel.com
We need to explicitly set the TLB Request Timer initial value in the
BW_BUDDY registers to 0x8 rather than relying on the hardware default.
v2: Apply missing REG_FIELD_PREP to ensure 0x8 is placed in the correct
bits during the rmw. (Jose)
Bspec: 52890
Bspec: 50044
Fixes: 3fa01d642f ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200219215655.2923650-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 87e04f7592)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228004320.127142-2-matthew.d.roper@intel.com
Commit 60c6a14b48 ("drm/i915/display: Force the state compute phase
once to enable PSR") was forcing the state compute too earlier
causing errors because not everything was initialized, so here
moving to the end of i915_driver_modeset_probe() when the display is
all initialized.
Also fixing the place where it disarm the force probe as during the
atomic check phase errors could happen like the ones due locking and
it would cause PSR to never be enabled if that happens.
Leaving the disarm to the atomic commit phase, intel_psr_enable() or
intel_psr_update() will be called even if the current state do not
allow PSR to be enabled.
v2: Check if intel_dp is null in intel_psr_force_mode_changed_set()
v3: Check intel_dp before get dev_priv
v4:
- renamed intel_psr_force_mode_changed_set() to
intel_psr_set_force_mode_changed()
- removed the set parameter from intel_psr_set_force_mode_changed()
- not calling intel_psr_set_force_mode_changed() from
intel_psr_enable/update(), directly setting it after the same checks
that intel_psr_set_force_mode_changed() does
- moved intel_psr_set_force_mode_changed() arm call to
i915_driver_modeset_probe() as it is a better for a PSR call, all the
functions calls happening between the old and the new function call
will cause issue
[backported to v5.6-rc3]
Fixes: 60c6a14b48 ("drm/i915/display: Force the state compute phase once to enable PSR")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1151
Tested-by: Ross Zwisler <zwisler@google.com>
Reported-by: Ross Zwisler <zwisler@google.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221212635.11614-1-jose.souza@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20200227205540.126135-1-jose.souza@intel.com
(cherry picked from commit df1a5bfc16)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As a disabled pipe in pipe_mask is not having a valid intel crtc,
driver wrongly populates the possible_crtcs mask while initializing
the plane for a CRTC. Fixing up the plane possible_crtcs mask.
changes since RFC:
- Simplify the possible_crtcs initialization. [Ville]
v2:
- Removed the unnecessary stack garbage possible_crtcs to
drm_universal_plane_init. [Ville]
v3:
- Combine the intel_crtc assignment and declaration. [Ville]
v4:
- Fix possible_crtcs abused bits from
intel_{primary,curosr,sprite}_plane_create(). [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163517.31234-1-anshuman.gupta@intel.com
Looks like the pipe rounding mode bit has moved from PIPE_CHICKEN to
PIPE_MISC on tgl. Frob the new location.
Bspec does still document the old bits as well, so I left the code
for them as is until we get clarification from the hw folks on
whether the old bits still do something useful.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163054.9509-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The #include has been splattered all over the place, but there are
precious few places, all .c files, that actually need it.
v2: remove leftover double newlines
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225133131.3301-1-jani.nikula@intel.com
On Tiger Lake we do not support source keying in the pixel formats P010,
P012, P016.
v2: Move WA to end of function. Create helper function for format
check. Less verbose debugging messaging.
v3: whitespace
v4(MattR):
- Actually return EINVAL to reject this combination.
- Pass format parameter as u32.
- Make test TGL-specific for now.
- Switch to per-device logging.
- Shorten/simplify comment.
Bspec: 52890
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224223651.3801646-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
On gen12, we no longer need to disable DC5/DC6 when when PG2 is in use
(which translates to cases where we're using VDSC on pipe A).
Bspec: 49193
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200220231843.3127468-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
- Clean up shadow batch after I915_EXEC_SECURE
- Drop assertion that active->fence is unchanged
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAl5Vau0ACgkQ+mJfZA7r
E8r5IQgAmBxjRdPYPcWP4IgsiyuhyUB+FTMOt84UonRdsE6dvalVibeS5CnaUKo0
8xfXnqubRYano7QiWbPhmQpIgeC2ZrM628xoThsySaitB4QG9eOHCpa1uXMWCd/j
/Jwh3tDiOdMpUunXPIlRFgNrNmGm5LM9APDEQDMouoknVb7GS4UaCMqlFU4LuBCm
2+sp4e5PHdJGrfalliNndICeD/bB1eBm6vrwKe4qNzDxyJJTF/1tcvzSyx/o1K2o
cAm3zvFmspWy5sC04XPFRG8POMjsobDBdD549wJjqah7z94DcDdFuRkZyHrZKBMW
2VLt3dUjTj1Z3Ib57ynqY24F7AIx3g==
=uXcx
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2020-02-25' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- A backmerge of drm-next solving conflicts on i915/gt/intel_lrc.c
- Clean up shadow batch after I915_EXEC_SECURE
- Drop assertion that active->fence is unchanged
Here goes drm-intel-next-2020-02-25:
- A backmerge of drm-next solving conflicts on i915/gt/intel_lrc.c
- Clean up shadow batch after I915_EXEC_SECURE
- Drop assertion that active->fence is unchanged
drm-intel-next-2020-02-24-1:
- RC6 fixes - Chris
- Add extra slice common debug register - Lionel
- Align virtual engines uabi_class/instance with i915_drm.h - Tvrtko
- Avoid potential division by zero in computing CS timestamp - Chris
- Avoid using various globals - Michal Winiarski, Matt Auld
- Break up long lists of GEM object reclaim - Chris
- Check that the vma hasn't been closed before we insert it - Chris
- Consolidate SDVO HDMI force_dvi handling - Ville
- Conversion to new logging and warn macros and functions - Pankaj, Wambul, Chris
- DC3CO fixes - Jose
- Disable use of hwsp_cacheline for kernel_context - Chris
- Display IRQ pre/post uninstall refactor - Jani
- Display port sync refactor for robustness and fixes - Ville, Manasi
- Do not attempt to reprogram IA/ring frequencies for dgfx - Chris
- Drop alpha_support for good in favor of force_probe - Jani
- DSI ACPI related fixes and refactors - Vivek, Jani, Rajat
- Encoder refactor for flexibility to add more information, especiallly DSI related - Jani, Vandita
- Engine workarounds refactor for robustness around resue - Daniele
- FBC simplification and tracepoints
- Various fixes for build - Jani, Kees Cook, Chris, Zhang Xiaoxu
- Fix cmdparser - Chris
- Fix DRM_I915_GEM_MMAP_OFFFSET - Chris
- Fix i915_request flags - Chris
- Fix inconsistency between pfit enable and scaler freeing - Stanislav
- Fix inverted warn_on on display code - Chris
- Fix modeset locks in sanitize_watermarks - Ville
- Fix OA context id overlap with idle context id - Umesh
- Fix pipe and vblank enable for MST - Jani
- Fix VBT handling for timing parameters - Vandita
- Fixes o kernel doc - Chris, Ville
- Force full modeset whenever DSC is enabled at probe - Jani
- Various GEM locking simplification and fixes - Jani , Chris, Jose
- Including some changes in preparation for making GEM execbuf parallel - Chris
- Gen11 pcode error codes - Matt Roper
- Gen8+ interrupt handler refactor - Chris
- Many fixes and improvements around GuC code - Daniele, Michal Wajdeczko
- i915 parameters improvements sfor flexible input and better debugability - Chris, Jani
- Ice Lake and Elkhart Lake Fixes and workarounds - Matt Roper, Jose, Vivek, Matt Atwood
- Improvements on execlists, requests and other areas, fixing hangs and also
improving hang detection, recover and debugability - Chris
- Also introducing offline GT error capture - Chris
- Introduce encoder->compute_config_late() to help MST - Ville
- Make dbuf configuration const - Jani
- Few misc clean ups - Ville, Chris
- Never allow userptr into the new mapping types - Janusz
- Poison rings after use and GTT scratch pages - Chris
- Protect signaler walk with RCU - Chris
- PSR fixes - Jose
- Pull sseu context updates under gt - Chris
- Read rawclk_freq earlier - Chris
- Refactor around VBT handling to allow geting information through the encoder - Jani
- Refactor l3cc/mocs availability - Chris
- Refactor to use intel_connector over drm_connector - Ville
- Remove i915_energy_uJ from debugfs - Tvrtko
- Remove lite restore defines - Mika Kuoppala
- Remove prefault_disable modparam - Chris
- Many selftests fixes and improvements - Chris
- Set intel_dp_set_m_n() for MST slaves - Jose
- Simplify hot plug pin handling and other fixes around pin and polled modes - Ville
- Skip CPU synchronization on dma-buf attachments - chris
- Skip global serialization of clear_range for bxt vtd - Chris
- Skip rmw for marked register - Chris
- Some other GEM Fixes - Chris
- Some small changes for satisfying static code analysis - Colin, Chris
- Suppress warnings for unused debugging locals
- Tiger Lake enabling, including re-enable -f RPS, workarounds and other display fixes and changes - Chris, Matt Roper, Mika Kuoppala, Anshuman, Jose, Radhakrishna, Rafael.
- Track hw reported context runtime - Tvrtko
- Update bug filling URL - Jani
- Use async bind for PIN_USER into bsw/bxt ggtt - Chris
- Use the kernel_context to measuer the breadcrumb size - Chris
- Userptr fixes and robustness for big pages - Matt Auld
- Various Display refactors and clean-ups, specially around logs and use of drm_i915_private - Jani, Ville
- Various display refactors and fixes, especially around cdclk, modeset, and encoder - Chris, Jani
- Various eDP/DP fixes around DPCD - Lyude
- Various fixes and refactors for better Display watermark handling - Ville, Stanislav
- Various other display refactors - Ville
- Various refactor for better handling of display plane states - Ville
- Wean off drm_pci_alloc/drm_pci_free - Chris
- Correctly terminate connector iteration- Ville
- Downgrade gen7 (ivb, byt, hsw) back to aliasing-ppgtt - Chris
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225185853.GA3282832@intel.com
skl_ddb_allocation_overlaps() num_entries hass been passed as
INTEL_NUM_PIPES, it should be I915_MAX_PIPES.
v2:
- Rebased.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-8-anshuman.gupta@intel.com
Add a WARN_ON for a disabled pipe in pipe_mask at
intel_get_crtc_for_pipe() function.
v2:
- Use drm_WARN_ON instead of WARN_ON.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-7-anshuman.gupta@intel.com
intel_plane_fb_max_stride should return the max stride of
primary plane for first available pipe in intel device info
pipe_mask.
Similarly glk_force_audio_cdclk() should also use the first
available CRTC instead of pipe 'A' crtc to force the cdclk
changes.
changes since RFC:
- Introduced a helper to get first intel_crtc intel_get_first_crtc. [Ville]
v1:
- Used intel_get_first_crtc() instead of PIPE_A crtc in
glk_force_audio_cdclk(). [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-6-anshuman.gupta@intel.com
Skip the transcoder whose pipe is disabled while
initializing transcoder error state in 3 non-contiguous
display pipe system.
v2:
- Don't skip EDP_TRANSCODER error state. [Ville]
- Use a helper has_transcoder(). [Ville]
v3:
- Removed DSI transcoder case from has_transcoder(),
and few other cosmetic changes. [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-4-anshuman.gupta@intel.com
we can't have (pipe == crtc->index) assumption in
driver in order to support 3 non-contiguous
display pipe system.
FIXME: Remove the WARN_ON(drm_crtc_index(&crtc->base) != crtc->pipe)
when we will fix all such assumption.
changes since RFC:
- Added again removed (pipe == crtc->index) WARN_ON.
- Pass drm_crtc_index instead of intel pipe in order to
call drm_handle_vblank().
v2:
- Used drm_crtc_handle_vblank()/drm_crtc_wait_one_vblank()
instead of drm_handle_vblank/drm_wait_one_vblank(). [Jani]
- Introduced intel_handle_vblank() helper to avoid sprinkle
of intel_crtc across irq_handlers. [Ville]
v3:
- Moved intel_handle_vblank() from header to i915_irq.c. [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-3-anshuman.gupta@intel.com
It should not be assumed that a disabled display pipe will be
always last the pipe.
for_each_pipe() should iterate over I915_MAX_PIPES and check
for the disabled pipe and skip that pipe so that it should not
initialize the intel crtc for any disabled pipes.
Due to changes in for_each_pipe() macro, it requires to handle
the below compilation error.
"suggest explicit braces to avoid ambiguous ‘else’
[-Werror=dangling-else]"
v2:
- Cosmetic changes, removed unwanted parentheses. [Ville]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224124004.26712-2-anshuman.gupta@intel.com
Split inte_modeset_init() to parts before and after irq install, to
facilitate further cleanup. The error paths are a mess, otherwise no
functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224120828.22105-1-jani.nikula@intel.com
Some DSI and VBT pending patches from Hans will apply
cleanly and with less ugly conflicts if they are rebuilt
on top of other patches that recently landed on drm-next.
Reference: https://patchwork.freedesktop.org/series/70952/
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com
Commit 60c6a14b48 ("drm/i915/display: Force the state compute phase
once to enable PSR") was forcing the state compute too earlier
causing errors because not everything was initialized, so here
moving to the end of i915_driver_modeset_probe() when the display is
all initialized.
Also fixing the place where it disarm the force probe as during the
atomic check phase errors could happen like the ones due locking and
it would cause PSR to never be enabled if that happens.
Leaving the disarm to the atomic commit phase, intel_psr_enable() or
intel_psr_update() will be called even if the current state do not
allow PSR to be enabled.
v2: Check if intel_dp is null in intel_psr_force_mode_changed_set()
v3: Check intel_dp before get dev_priv
v4:
- renamed intel_psr_force_mode_changed_set() to
intel_psr_set_force_mode_changed()
- removed the set parameter from intel_psr_set_force_mode_changed()
- not calling intel_psr_set_force_mode_changed() from
intel_psr_enable/update(), directly setting it after the same checks
that intel_psr_set_force_mode_changed() does
- moved intel_psr_set_force_mode_changed() arm call to
i915_driver_modeset_probe() as it is a better for a PSR call, all the
functions calls happening between the old and the new function call
will cause issue
Fixes: 60c6a14b48 ("drm/i915/display: Force the state compute phase once to enable PSR")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1151
Tested-by: Ross Zwisler <zwisler@google.com>
Reported-by: Ross Zwisler <zwisler@google.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221212635.11614-1-jose.souza@intel.com
Restore the previous WARN_ON(cond) so that we don't complain about poor
old Cherryview.
Fixes: eb020ca3d4 ("drm/i915/display/dp: Make WARN* drm specific where drm_device ptr is available")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200223173959.3885742-1-chris@chris-wilson.co.uk
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/gpu/drm/i915/display/intel_display.c: In function ‘check_digital_port_conflicts’:
drivers/gpu/drm/i915/display/intel_display.c:12963:17: warning: statement will never be executed [-Wswitch-unreachable]
12963 | unsigned int port_mask;
| ^~~~~~~~~
drivers/gpu/drm/i915/intel_pm.c: In function ‘vlv_get_fifo_size’:
drivers/gpu/drm/i915/intel_pm.c:474:7: warning: statement will never be executed [-Wswitch-unreachable]
474 | u32 dsparb, dsparb2, dsparb3;
| ^~~~~~
drivers/gpu/drm/i915/intel_pm.c: In function ‘vlv_atomic_update_fifo’:
drivers/gpu/drm/i915/intel_pm.c:1997:7: warning: statement will never be executed [-Wswitch-unreachable]
1997 | u32 dsparb, dsparb2, dsparb3;
| ^~~~~~
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/202002201602.92CADF7D@keescook
We need to explicitly set the TLB Request Timer initial value in the
BW_BUDDY registers to 0x8 rather than relying on the hardware default.
v2: Apply missing REG_FIELD_PREP to ensure 0x8 is placed in the correct
bits during the rmw. (Jose)
Bspec: 52890
Bspec: 50044
Fixes: 3fa01d642f ("drm/i915/tgl: Program BW_BUDDY registers during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200219215655.2923650-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
On gen11 we only needed to program MBus credits into MBUS_ABOX_CTL
during display initialization, but on gen12 we're now supposed to
program the same values into MBUS_ABOX1_CTL and MBUS_ABOX2_CTL as well.
v2:
- Program registers with rmw to preserve contents of unrelated bits.
- Switch to the new display uncore helpers.
Bspec: 49213
Bspec: 50096
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204011032.582737-2-matthew.d.roper@intel.com
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
It wasn't terribly clear from the bspec's wording, but after discussion
with the hardware folks, it turns out that we need to preserve the
pre-existing contents of the MBUS ABOX control register when
initializing a few specific bits.
Bspec: 49213
Bspec: 50096
Fixes: 4cb4585e5a ("drm/i915/icl: initialize MBus during display init")
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204011032.582737-1-matthew.d.roper@intel.com
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
We have to write quite a few registers when programming the
pipe scaler. Let's use intel_de_write_fw() for these to reduce
the lockdep overhead a bit. All plane registers (including plane
scaler) already do this.
We already had a few accidental intel_de_write_fw() in there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200212161738.28141-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently we only set the DRM_CONNECTOR_POLL_{DISCONNECT,CONNECT}
bits in intel_connector->polled (the base setting), leading to
some confusing looking code to reset drm_connector->polled
(the actual setting) to DRM_CONNECTOR_POLL_HPD. Let's set
intel_connector->polled = DRM_CONNECTOR_POLL_HPD for all hpd
capable connectors, and then we don't need so many special
cases in the hotplug code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205183546.9291-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
No point in looping over all connectors for each hpd pin. Just loop
over each connector first and deal with each one's hpd pin. Then
loop over all the hpd pins to mark them as enabled again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205183546.9291-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkEjOgAKCRDj7w1vZxhR
xeaDAQD+1MludG4RmfQhATe4jTsPC1r2x63OF2CA0ChMGHXJyQEA8qqQ+8y1Cd/u
PZ3PpcTl4qYYHgzJ6FwW7kDPTvlaZQE=
=IJAt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-02-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.7:
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200210093421.xu4sofldm6wm6xq6@gilmour.lan
If one of the synced crtcs needs a full modeset, we need
to make sure all the synced crtcs are forced a full
modeset.
v3:
* Remove ~BIT(cpu_trans) which is a nop (Ville)
* use get_new_crtc_state and remove error check (Ville)
v2:
* Add tiles based on cpu_trans check (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-3-manasi.d.navare@intel.com
This patch pushes out the computation of master and slave
transcoders in crtc states after encoder's compute_config hook.
This ensures that the assigned master slave crtcs have exact same
mode and timings which is a requirement for Port sync mode
to be enabled.
v3:
* Make crtc_state const, remove crtc state NULL init (Ville)
v2:
* Correct indentation
* Rename to intel_ddi_port_sync_transcoders (Ville)
* remove unwanted debug (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-2-manasi.d.navare@intel.com
Add an optional secondary encoder state compute hook. This gets
called after the normak .compute_config() has been called for
all the encoders in the state. Thus in the new hook we can rely
on all derived state populated by .compute_config() to be already
set up. Should be useful for MST and port sync master/slave
transcoder selection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-1-manasi.d.navare@intel.com
Split intel_modeset_driver_remove() to two, the part with working irqs
before irq uninstall, and the part after irq uninstall. Move
irq_unintall() closer to the layer it belongs.
The error path in i915_driver_modeset_probe() looks obviously weird
after this, but remains as good or broken as it ever was. No functional
changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214135058.7580-1-jani.nikula@intel.com
drm_pci_alloc and drm_pci_free are just very thin wrappers around
dma_alloc_coherent, with a note that we should be removing them.
Furthermore since
commit de09d31dd3
Author: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Date: Fri Jan 15 16:51:42 2016 -0800
page-flags: define PG_reserved behavior on compound pages
As far as I can see there's no users of PG_reserved on compound pages.
Let's use PF_NO_COMPOUND here.
drm_pci_alloc has been declared broken since it mixes GFP_COMP and
SetPageReserved. Avoid this conflict by weaning ourselves off using the
abstraction and using the dma functions directly.
Reported-by: Taketo Kabe
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1027
Fixes: de09d31dd3 ("page-flags: define PG_reserved behavior on compound pages")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202153934.3899472-1-chris@chris-wilson.co.uk
(cherry picked from commit c6790dc223)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We lack full state readout of DSC config, which may lead to DSC enable
using a config that's all zeros, failing spectacularly. Force full
modeset and thus compute config at probe to get a sane state, until we
implement DSC state readout. Any fastset that did appear to work with
DSC at probe, worked by coincidence. [1] is an example of a change that
triggered the issue on TGL DSI DSC.
[1] http://patchwork.freedesktop.org/patch/msgid/20200212150102.7600-1-ville.syrjala@linux.intel.com
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: fbacb15ea8 ("drm/i915/dsc: add basic hardware state readout support")
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213140412.32697-3-stanislav.lisovskiy@intel.com
(cherry picked from commit a4277aa398)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Voltage level depends not only on the cdclk, but also on the DDI clock.
Last time the bspec voltage level table for EHL was updated, we only
updated the cdclk requirements, but forgot to account for the new port
clock criteria.
Bspec: 21809
Fixes: d147483884 ("drm/i915/ehl: Update voltage level checks")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 9d5fd37ed7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5JsVQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHZEH+wddtJO4dZk5TZdF
KZB2w2ldsCvrBZAmas1TVvm8ncvUf+ATUZcSIzvZ3YbLmxsuLF2Cz3kD+n+36Mvy
ejwq8Scl7jwnouYps/Gfd6rRj/uCafqST4qp15GMGeiy2ST4A8dJrv5IAgZhD8/N
SN1bSr1AXpZ2JlEzzLDQ/NdVoNMS6IzCOsaINZcc60/XQoQZFRBWamMJFqu+CmXD
SBJOybQNFJhziy45cGZSAl+67sSCcoPftwTs0Stu4CJsvFWRb3MsbNTDS51Hjcc4
3tdgGOhoNXzyzZr96MEAHmiaW4VLQv0PGgUfOajE35viMz48OrwCTru8Kbuae3XM
YHV4qJk=
=yiem
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkpecgAKCRDj7w1vZxhR
xU4CAQD/8ZzfYroiiEI7FHEgvnuldGYZqA9kbNAO2Vueeac0OgD+Jojewdxy+pJ9
dxfA/POdtzx3hOdN+U1YgaDC0hbXwww=
=XgKq
-----END PGP SIGNATURE-----
Merge v5.6-rc2 into drm-misc-next
Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently when we load the driver we set distrust_bios_wm=true, which
will cause active_pipe_changes to get flagged even when we're not
toggling any pipes on/off. The reason being that we want to fully
redistribute the dbuf among the active pipes and ignore whatever
state the firmware left behind.
Unfortunately when the code flags active_pipe_changes it doesn't
set state->modeset to true, which means the hardware dbuf state
won't actually get updated. Hence the hardware and software
states go out of sync, which can result in planes trying to use a
disabled dbuf slice. Suprisingly that only seems to corrupt the
display rather than making the whole display engine keel over.
Let's fix this for now by flagging state->modeset whenever
distrust_bios_wm is set.
Eventually we'll likely want to rip out all of this mess and
introduce proper statye tracking for dbuf. But that requires
more work. Toss in a FIXME to that effect.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: ff2cd8635e ("drm/i915: Correctly map DBUF slices to pipes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213140412.32697-4-stanislav.lisovskiy@intel.com
We lack full state readout of DSC config, which may lead to DSC enable
using a config that's all zeros, failing spectacularly. Force full
modeset and thus compute config at probe to get a sane state, until we
implement DSC state readout. Any fastset that did appear to work with
DSC at probe, worked by coincidence. [1] is an example of a change that
triggered the issue on TGL DSI DSC.
[1] http://patchwork.freedesktop.org/patch/msgid/20200212150102.7600-1-ville.syrjala@linux.intel.com
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Fixes: fbacb15ea8 ("drm/i915/dsc: add basic hardware state readout support")
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213140412.32697-3-stanislav.lisovskiy@intel.com
TGL BIOS seems to enable both DBuf slices ocasionally, depending
how many displays are connected, while i915 according to BSpec
was powering on S1 DBuf slice, until a modeset was done.
This was causing a brief flash during the boot as we were
disabling slice, previously used by BIOS with that.
To prevent this, now we are ensuring tht we are enabling
_at least_ one slice, but if there are more, let's not
power them off.
Fixes: ff2cd8635e ("drm/i915: Correctly map DBUF slices to pipes")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213140412.32697-2-stanislav.lisovskiy@intel.com
Commit 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for
DDI platforms") moved the intel_dp_set_m_n() from hsw_crtc_enable()
to intel_ddi_pre_enable_dp() but it missed add it to
intel_mst_pre_enable_dp() causing MST slaves to not work.
v2: Not setting intel_ddi_set_dp_msa() twice for MST master
Fixes: 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for DDI platforms")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211185008.30806-1-jose.souza@intel.com
The i915_debugfs.c has grown more than a little unwieldy. Split out the
display related debugfs code to a file of its own under display/,
initialized with a separate call. No functional changes.
v2:
- Also moved i915_frontbuffer_tracking, i915_gem_framebuffer,
i915_power_domain_info, i915_dmc_info, i915_ipc_status (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211161451.6867-2-jani.nikula@intel.com
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
The DMC firmware is about display. Move the handling under display. No
functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211161451.6867-1-jani.nikula@intel.com
drm->dev_private is to be avoided. Use to_i915() on the struct
drm_device pointer instead. Rename the affected local dev_priv variables
to i915 while at it.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211134427.31605-1-jani.nikula@intel.com
VBLANK callbacks in struct drm_driver are deprecated in favor of their
equivalents in struct drm_crtc_funcs. Convert i915 over.
The callback struct drm_driver.get_scanout_position() is deprecated
in favor of struct drm_crtc_helper_funcs.get_scanout_position().
i915 doesn't use CRTC helpers. Instead pass i915's implementation of
get_scanout_position() to DRM core's
drm_crtc_vblank_helper_get_vblank_timestamp_internal().
v3:
* rename dcrtc to _crtc
* use intel_ prefix for i915_crtc_get_vblank_timestamp()
* update for drm_crtc_vblank_helper_get_vblank_timestamp_internal()
v2:
* use DRM's implementation of get_vblank_timestamp()
* simplify function names
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123135943.24140-8-tzimmermann@suse.de
s/before/after/ again after accidentally changing it the
other way in commit 5604e9ceae ("drm/i915: Simplify
intel_set_cdclk_{pre,post}_plane_update() calling convention")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204154803.25403-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Accidentally removed the 'ret=0' initialization, and thus
we're potentially looking at some stack garbage here.
The whole 'ret = do_stuff; if (!ret) do_other_stuff;' pattern
confuses my brain so let's replace it with the standard
immediate return thing.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 28a30b45f5 ("drm/i915: Convert cdclk to global state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207152228.1054-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in
i915/display/intel_dp_link_training.c.
This also involves extracting the drm_i915_private device pointer from
the intel_dp type to use in the various macros.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206080014.13759-3-wambui.karugax@gmail.com
As Gen12 onwards there are HDCP instances for each transcoder
instead of port, remove the (port < PORT_E) hdcp support
limitation for platform >= Gen12.
v2:
- Nuke the comment and cosmetic changes. [Jani]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207144116.20172-1-anshuman.gupta@intel.com
A recent bspec update added an extra voltage level that we didn't have
on ICL and new criteria for selecting the level.
Bspec: 49208
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-2-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Voltage level depends not only on the cdclk, but also on the DDI clock.
Last time the bspec voltage level table for EHL was updated, we only
updated the cdclk requirements, but forgot to account for the new port
clock criteria.
Bspec: 21809
Fixes: d147483884 ("drm/i915/ehl: Update voltage level checks")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Add a basic description about how DC3CO works to help people not
familiar with it.
While at it, I also improved the delayed work handle and function
names and removed a debug message that is ambiguous and not much
useful, no changes in behavior here.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205214945.131012-1-jose.souza@intel.com
intel_prepare_plane_fb() will always pin plane_state->hw.fb whenever
it is present. We copy that from the master plane to the slave plane,
but we fail to copy the corresponding ggtt view. Thus when it comes time
to pin the slave plane's fb we use some stale ggtt view left over from
the last time the plane was used as a non-slave plane. If that previous
use involved 90/270 degree rotation or remapping we'll try to shuffle
the pages of the new fb around accordingingly. However the new
fb may be backed by a bo with less pages than what the ggtt view
rotation/remapped info requires, and so we we trip a GEM_BUG().
Steps to reproduce on icl:
1. plane 1: whatever
plane 6: largish !NV12 fb + 90 degree rotation
2. plane 1: smallish NV12 fb
plane 6: make invisible so it gets slaved to plane 1
3. GEM_BUG()
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/951
Fixes: 1f594b209f ("drm/i915: Remove special case slave handling during hw programming, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 103605e0d1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 21fd23ac22 ("drm/i915: move pipe, pch and vblank enable to
encoders on DDI platforms") pushed pipe and vblank enable to encoders on
DDI platforms, however it missed the DP MST encoder. Fix it.
Fixes: 21fd23ac22 ("drm/i915: move pipe, pch and vblank enable to encoders on DDI platforms")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reported-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Tested-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205082959.31317-1-jani.nikula@intel.com
Fix htotal and vtotal parameters derived from DTD block of VBT. The
values miss the back porch.
Fixes: 33ef6d4fd8 ("drm/i915/vbt: Handle generic DTD block")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200124125829.16973-1-vandita.kulkarni@intel.com
(cherry picked from commit ad278f3584)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Remove the i2c_bus_num >= 0 check from the adapter lookup function
as this would prevent ACPI bus number override. This check was mainly
there to return early if the bus number has already been found but we
anyway return in the next line if the slave address does not match.
Fixes: 8cbf89db29 ("drm/i915/dsi: Parse the I2C element from the VBT MIPI sequence block (v3)")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200118005848.20382-1-vivek.kasireddy@intel.com
(cherry picked from commit de409661c4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The post-fastset "does anyone still need a full modeset?" for
port sync looks busted. The outer loop bails out of a full modeset
is still needed by the current crtc, and then we skip forcing
a full modeset on the related crtcs. That's totally the opposite
of what we want.
The MST path has the logic mostly the other way around so it
looks correct. To fix the port sync case let's follow the MST
logic for both. So, if the current crtc already needs a modeset
we do nothing. otherwise we check if any of the related crtcs
needs a modeset, and if so we force a full modeset for the
current crtc.
And while at let's change the else if to a plain if to so
we don't have needless coupling between the MST and port sync
checks.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Fixes: 05a8e45136 ("drm/i915/display: Use external dependency loop for port sync")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115190813.17971-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit d0eed1545f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Perform the i2c bus/adapter lookup from ACPI Namespace only if ACPI is
enabled in the kernel config. If ACPI is not enabled or if the lookup
fails, we'll fallback to using the VBT for identifying the i2c bus.
v2: Add fixes tag (Jani)
Fixes: 8cbf89db29 ("drm/i915/dsi: Parse the I2C element from the VBT MIPI sequence block (v3)")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115012305.27395-1-vivek.kasireddy@intel.com
(cherry picked from commit 960287ca58)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit d2a4bb6f8b.
So, turns out that this ended up just breaking things. While many
laptops incorrectly advertise themselves as supporting PWM backlight
controls, they actually will only work with DPCD backlight controls.
Unfortunately, it also seems there are a number of systems which
advertise DPCD backlight controls in their eDP DPCD but don't actually
support them. Talking with some laptop manufacturers has shown it might
be possible to probe this support via the EDID (!?!?) but I haven't been
able to confirm that this would work on any other manufacturer's
systems.
So in the mean time, we'll just revert this commit for now and go back
to the old way of doing things.
Fixes: d2a4bb6f8b ("drm/i915: Don't use VBT for detecting DPCD backlight controls")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204192823.111404-2-lyude@redhat.com
TGL is suffering of timeouts and fifo underruns when disabling
transcoder in MST mode, this is fixed by set TRANS_DDI_MODE_SELECT to
0(HDMI mode) when clearing DDI select.
Although BSpec disable sequence don't require this step, it is a
harmless change and it is also done by Windows driver.
Anyhow HW team was notified about that but it can take some time to
documentation to be updated.
A case that always lead to those issues is:
- do a modeset enabling pipe A and pipe B in the same MST stream
leaving A as master
- disable pipe A, promote B as master doing a full modeset in A
- enable pipe A, changing the master transcoder back to A(doing a
full modeset in B)
- Pow: underruns and timeouts
The transcoders involved will only work again when complete disabled
and their power wells turned off causing a reset in their registers.
v2: Setting TRANS_DDI_MODE_SELECT to default when clearing DDI select
not anymore when disabling TRANS_DDI, both work but this one looks
more safe. (Ville comment)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200203225549.152301-1-jose.souza@intel.com
Start manipulating DBuf slices as a mask,
but not as a total number, as current approach
doesn't give us full control on all combinations
of slices, which we might need(like enabling S2
only can't enabled by setting enabled_slices=1).
Removed wrong code from intel_get_ddb_size as
it doesn't match to BSpec. For now still just
use DBuf slice until proper algorithm is implemented.
Other minor code refactoring to get prepared
for major DBuf assignment changes landed:
- As now enabled slices contain a mask
we still need some value which should
reflect how much DBuf slices are supported
by the platform, now device info contains
num_supported_dbuf_slices.
- Removed unneeded assertion as we are now
manipulating slices in a more proper way.
v2: Start using enabled_slices in dev_priv
v3: "enabled_slices" is now "enabled_dbuf_slices_mask",
as this now sits in dev_priv independently.
v4: - Fixed debug print formatting to hex(Matt Roper)
- Optimized dbuf slice updates to be used only
if slice union is different from current conf(Matt Roper)
- Fixed some functions to be static(Matt Roper)
- Created a parameterized version for DBUF_CTL to
simplify DBuf programming cycle(Matt Roper)
- Removed unrequred field from GEN10_FEATURES(Matt Roper)
v5: - Removed redundant programming dbuf slices helper(Ville Syrjälä)
- Started to use parameterized loop for hw readout to get slices
(Ville Syrjälä)
- Added back assertion checking amount of DBUF slices enabled
after DC states 5/6 transition, also added new assertion
as starting from ICL DMC seems to restore the last DBuf
power state set, rather than power up all dbuf slices
as assertion was previously expecting(Ville Syrjälä)
v6: - Now using enum for DBuf slices in this patch (Ville Syrjälä)
- Removed gen11_assert_dbuf_enabled and put gen9_assert_dbuf_enabled
back, as we really need to have a single unified assert here
however currently enabling always slice 1 is enforced by BSpec,
so we will have to OR enabled slices mask with 1 in order
to be consistent with BSpec, that way we can unify that
assertion and against the actual state from the driver, but
not some hardcoded value.(concluded with Ville)
- Remove parameterized DBUF_CTL version, to extract it to another
patch.(Ville Syrjälä)
v7:
- Removed unneeded hardcoded return value for older gens from
intel_enabled_dbuf_slices_mask - this now is handled in a
unified manner since device info anyway returns max dbuf slices
as 1 for older platforms(Matthew Roper)
- Now using INTEL_INFO(dev_priv)->num_supported_dbuf_slices instead
of intel_dbuf_max_slices function as it is trivial(Matthew Roper)
v8: - Fixed icl_dbuf_disable to disable all dbufs still(Ville Syrjälä)
v9: - Renamed _DBUF_CTL_S to DBUF_CTL_S(Ville Syrjälä)
- Now using power_domain mutex to protect from race condition, which
can occur because intel_dbuf_slices_update might be running in
parallel to gen9_dc_off_power_well_enable being called from
intel_dp_detect for instance, which causes assertion triggered by
race condition, as gen9_assert_dbuf_enabled might preempt this
when registers were already updated, while dev_priv was not.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202230630.8975-6-stanislav.lisovskiy@intel.com
Now start using parameterized DBUF_CTL instead
of hardcoded, this would allow shorter access
functions when reading or storing entire state.
Tried to implement it in a MMIO_PIPE manner, however
DBUF_CTL1 address is higher than DBUF_CTL2, which
implies that we have to now subtract from base
rather than add.
v2: - Removed unneeded DBUF_CTL_DIST and DBUF_CTL_ADDR
macros. Started to use _PICK construct as suggested
by Matt Roper.
v3: - _DBUF_CTL_S* to DBUF_CTL_S*, changed X to "slice"
in macro(Ville Syrjälä)
- Introduced enum for enumerating DBUF slices(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202230630.8975-5-stanislav.lisovskiy@intel.com
During full modeset, global state(i.e dev_priv) is protected
by locking the crtcs in state, otherwise global state is not
serialized. Also if it is not a full modeset, we anyway
don't need to change DBuf slice configuration as Pipe configuration
doesn't change.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202230630.8975-4-stanislav.lisovskiy@intel.com
Current DBuf slices update wasn't done in proper
place, especially its "post" part, which should
disable those only once vblank had passed and
all other changes are committed.
v2: Fix to use dev_priv and intel_atomic_state
instead of skl_ddb_values
(to be nuked in Villes patch)
v3: Renamed "enabled_slices" to "enabled_dbuf_slices_num"
(Matt Roper)
v4: - Rebase against drm-tip.
- Move post_update closer to optimize_watermarks,
to prevent unneeded noise from underrun reporting
(Ville Syrjälä)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202230630.8975-3-stanislav.lisovskiy@intel.com
Current consensus that it is redundant as
we already have skl_ddb_values struct out there,
also this struct contains only single member
which makes it unnecessary.
v2: As dirty_pipes soon going to be nuked away
from skl_ddb_values, evacuating enabled_slices
to safer in dev_priv.
v3: Changed "enabled_slices" to be "enabled_dbuf_slices_num"
(Matt Roper)
v4: - Wrapped the line getting number of dbuf slices(Matt Roper)
- Removed indeed redundant skl_ddb_values declaration(Matt Roper)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202230630.8975-2-stanislav.lisovskiy@intel.com
As only the display codes tries to pin its preallocated framebuffer into
an exact location in the GGTT, remove the convenience function and make
the pin management explicit in the display code. Then throughout the
display management, we track the framebuffer and its plane->vma; with
less single purpose code and ready for first class i915_vma.
In doing so, this should fix the BUG_ON(vma->pages) on fi-kbl-soraka.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204094801.877288-2-chris@chris-wilson.co.uk
I am about to stuff more objects into the plane_config and would like to
have it clean up after itself. Move the current framebuffer release into
a common function so it can be extended with the new object with
relative ease.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200204094801.877288-1-chris@chris-wilson.co.uk
The DDI encoder code shouln't have to know about the guts of
HDCP. Abstract the pipe update code to a new intel_hdcp_update_pipe() in
intel_hdcp.c. No functional changes.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128163803.5954-1-jani.nikula@intel.com
Let's make sure encoder->hpd_pin and connector->polled are mirror
images of each other (when we want to use polling). The other
potentially polled connectors (sdvo and tv) already get this right.
Also nuke the redundant force_hotplug_required initialization
(the thing is kzalloc()ed).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121171100.4370-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Simplify the hotplug code connector->encoder->hpd_pin handling
by introducing a helper for exactly this purpose.
In the helper we can neatly deal with the potential lack of an
attached encoder on fresh MST connectors leaving the rest of the
hpd code oblivious to such details.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121171100.4370-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm_pci_alloc and drm_pci_free are just very thin wrappers around
dma_alloc_coherent, with a note that we should be removing them.
Furthermore since
commit de09d31dd3
Author: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Date: Fri Jan 15 16:51:42 2016 -0800
page-flags: define PG_reserved behavior on compound pages
As far as I can see there's no users of PG_reserved on compound pages.
Let's use PF_NO_COMPOUND here.
drm_pci_alloc has been declared broken since it mixes GFP_COMP and
SetPageReserved. Avoid this conflict by weaning ourselves off using the
abstraction and using the dma functions directly.
Reported-by: Taketo Kabe
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1027
Fixes: de09d31dd3 ("page-flags: define PG_reserved behavior on compound pages")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200202153934.3899472-1-chris@chris-wilson.co.uk
Let's add a copy of the active_pipes bitmask into the cdclk_state.
While this is duplicating a bit of information we may already
have elsewhere, I think it's worth it to decopule the cdclk stuff
from whatever else wants to use that bitmask. Also we want to get
rid of all the old ad-hoc global state which is what the current
bitmask is, so this removes one obstacle.
The one extra thing we have to remember is write locking the cdclk
state whenever the bitmask changes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-19-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's convert cdclk_state to be a proper global state. That allows
us to use the regular atomic old vs. new state accessor, hopefully
making the code less confusing.
We do have to deal with a few more error cases in case the cdclk
state duplication fails. But so be it.
v2: Fix new plane min_cdclk vs. old crtc min_cdclk check
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121140353.25997-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Extract a small helper to compute the active pipes bitmask
based on the old bitmask + the crtcs in the atomic state.
I want to decouple the cdclk state entirely from the current
global state so I want to track the active pipes also inside
the (to be introduced) full cdclk state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-17-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that we have the more formal global state thing let's
use if for memory bandwidth tracking. No real difference
to the current private object usage since we already
tried to avoid taking the single serializing lock needlessly.
But since we're going to roll the global state out to more
things probably a good idea to unify the approaches a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-16-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Our current global state handling is pretty ad-hoc. Let's try to
make it better by imitating the standard drm core private object
approach.
The reason why we don't want to directly use the private objects
is locking; Each private object has its own lock so if we
introduce any global private objects we get serialized by that
single lock across all pipes. The global state apporoach instead
uses a read/write lock type of approach where each individual
crtc lock counts as a read lock, and grabbing all the crtc locks
allows one write access.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-15-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Give the cdclk init/uninit functions a _hw suffix to make
it clear they are about initializing the actual hardware.
I'll be wanting to to add a intel_cdclk_init() which is
purely initializing software structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
intel_cdclk_needs_cd2x_update() is named rather confusingly.
We don't have to do a cd2x update, rather we are allowed to
do one (as opposed to a full PLL reprogramming with its heavy
handed modeset). So let's rename the function to
intel_cdclk_can_cd2x_update().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Move the min_cdclk[] and min_voltage_level[] arrays under the
rest of the cdclk state. And while at it provide a simple
helper (intel_cdclk_clear_state()) to clear the state during
the ww_mutex backoff dance.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-6-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Move the initial setup of state->{cdclk,min_cdclk[],min_voltage_level[]}
into intel_modeset_calc_cdclk(), and we'll move the counterparts into
intel_cdclk_swap_state(). This encapsulates the cdclk state much better.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The linetime watermarks really have very little in common with the
plane watermarks. It looks to be cleaner to simply track them in
the crtc_state and program them from the normal modeset/fastset
paths.
The only dark cloud comes from the fact that the register is
still supposedly single buffered. So in theory it might still
need some form of two stage programming. Note that even though
HSW/BDWhave two stage programming we never computed any special
intermediate values for the linetime watermarks, and on SKL+
we don't even have the two stage stuff plugged in since everything
else is double buffered. So let's assume it's all fine and
continue doing what we've been doing.
Actually on HSW/BDW the value should not even change without
a full modeset since it doesn't account for pfit downscaling.
Thus only fastboot might be affected. But on SKL+ the pfit
scaling factor is take into consideration so the value may
change during any fastset.
As a bonus we'll plug this thing into the state
checker/dump now.
v2: Rebase due to bigjoiner prep
v2: Only compute ips linetime for IPS capable pipes.
Bspec says the register values is ignored for other
pipes, but in fact it can't even be written so the
state checker becomes unhappy if we don't compute
it as zero.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200120174728.21095-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Enable the dsi transcoder, panel and backlight as part of
encoder->enable and not encoder->pre_enable. We need to have pipe src
size, among other things, set before enabling the transcoder, to avoid
FIFO underruns and possibly other issues.
v2 by Jani:
- Rebase on the crtc enable sequence update
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128162850.8660-2-jani.nikula@intel.com
To allow better flexibility for encoder specific code, push
intel_enable_pipe(), lpt_pch_enable() and intel_crtc_vblank_on() down to
the encoders from hsw_crtc_enable().
There's slight duplication, but also more clarity with the reduced
conditional statements.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128162850.8660-1-jani.nikula@intel.com
Avoid releasing the same stolen nodes causing a use-after-free and/or
explosions as the self-checks fail, as __intel_fbc_cleanup_cfb() may be
called multiple times during module unload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200130135136.1878646-1-chris@chris-wilson.co.uk
The aux ch is used for more than DDC, so let's give it a better
name. For maximum ease let's include both the AUX ch identifier
and the port identifier (for cases where the VBT has redefined
the relationship of the two).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123154542.12271-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
We've added more internal things that use modeset locks and
thus we need to be prepared for intel_atomic_check() grabbing
more locks than what our initial drm_modeset_lock_all_ctx()
took. So we're missing the backoff handling here.
Also drm_atomic_helper_duplicate_state() works against us
by clearing state->acquire_ctx in anticipation of
drm_atomic_helper_commit_duplicated_state() being used to
commit the state.
We could probably just reset acquire_ctx back, but instead
let's just rewrite the whole thing without using either of
those "helpers". There's also no need to add any connectors
to the state here since we just want the new watermarks
which don't depend on connectors.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122204329.2477-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Despite that during hw readout we seem to have scalers assigned
to pipes, then call atomic_setup_scalers, at the commit stage in
skl_update_scaler there is a check, that if we have fb src and
dest of same size, we stage freeing of that scaler.
However we don't update pfit.enabled flag then, which makes
the state inconsistent, which in turn triggers a WARN_ON
in skl_pfit_enable, because we have pfit enabled,
but no assigned scaler.
To me this looks weird that we kind of do the decision
to use or not use the scaler at skl_update_scaler stage
but not in intel_atomic_setup_scalers, moreover
not updating the whole state consistently.
This fix is to not free the scaler if we have pfit.enabled
flag set, so that the state is now consistent
and the warnings are gone.
v2: - Put pfit.enable check into crtc specific place
(Ville Syrjälä)
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/577
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200124172301.16484-1-stanislav.lisovskiy@intel.com
drivers/gpu/drm/i915/display/intel_atomic.c:185: warning: Function parameter or member 'state' not described in 'intel_connector_needs_modeset'
drivers/gpu/drm/i915/display/intel_atomic.c:185: warning: Function parameter or member 'connector' not described in 'intel_connector_needs_modeset'
drivers/gpu/drm/i915/display/intel_fbc.c:1124: warning: Function parameter or member 'state' not described in 'intel_fbc_enable'
drivers/gpu/drm/i915/display/intel_fbc.c:1124: warning: Excess function parameter 'crtc_state' description in 'intel_fbc_enable'
drivers/gpu/drm/i915/display/intel_fbc.c:1124: warning: Excess function parameter 'plane_state' description in 'intel_fbc_enable'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200126195654.2172937-1-chris@chris-wilson.co.uk
This patch converts various instances of the printk based logging macros
in drm/i915/display/intel_display.c to the new struct drm_device based
logging macros.
In some instances, this involves extracting the struct drm_i915_private
device from various intel types and using it in the macros.
v2: use correct variable name in assignment over variable type.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121214641.7262-1-wambui.karugax@gmail.com
Perhaps in some cases the BIOS/GOP or other firmware may turn on
PHY A but may not program the MUX correctly. Therefore, re-program
PHY A if it is determined after reading the VBT that the value
programmed for the MUX bit does not match the expected value.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121235848.8457-1-vivek.kasireddy@intel.com
A recent change in BSpec allow us to change EXTLINE while transcoder
is enabled so this allow us to change it even when doing the first
fastset after taking over previous hardware state set by BIOS.
BIOS don't enable PSR, so if sink supports PSR it will be enabled on
the first fastset, so moving the EXTLINE compute and set to PSR flows
allow us to simplfy a bunch of code.
This will save a lot of time in all the IGT tests that uses CRC, as
when PSR2 is enabled CRCs are not generated, so we switch to PSR1, so
the previous code would compute dc3co_exitline=0 causing a full
modeset that would shutdown pipe, enable and train link.
v2: only programming EXTLINE when DC3CO is enabled
BSpec: 49196
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-2-jose.souza@intel.com
This will calculaet the DC3CO exit delay only once per full modeset.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-1-jose.souza@intel.com
Remove the i2c_bus_num >= 0 check from the adapter lookup function
as this would prevent ACPI bus number override. This check was mainly
there to return early if the bus number has already been found but we
anyway return in the next line if the slave address does not match.
Fixes: 8cbf89db29 ("drm/i915/dsi: Parse the I2C element from the VBT MIPI sequence block (v3)")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200118005848.20382-1-vivek.kasireddy@intel.com
In the port sync mode, for the master crtc, the master_transcoder is INVALID.
In that case since its value is -1, do not set the bit in the bitmask.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0eed1545f ("drm/i915: Fix post-fastset modeset check for port sync")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123002415.31478-1-manasi.d.navare@intel.com
Add convenience helpers for the most common uncore operations with
struct drm_i915_private * as context rather than struct intel_uncore *.
The goal is to replace all instances of I915_READ(),
I915_POSTING_READ(), I915_WRITE(), I915_READ_FW(), and I915_WRITE_FW()
in display/ with these, to finally be able to get rid of the implicit
dev_priv local parameter use.
The idea is that any non-u32 reads or writes are special enough that
they can use the intel_uncore_* functions directly.
v2:
- rename the file intel_de.h
- move intel_de_wait_for_* there too
- also add de fw helpers
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121113915.9813-1-jani.nikula@intel.com
We've already pinned the vma and fence by the time we try to
deal with implicit fencing. Properly unpin the vma and fence
if the fence setup fails instead of just bailing straight out
from .prepare_fb(). As can be expected
drm_atomic_helper_prepare_planes() will not call .cleanup_fb()
for the plane whose .prepare_fb() failed so we must do the
cleanup ourself.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
intel_prepare_plane_fb() bails early if there is no fb (or rather
no obj, which is the same thing). intel_cleanup_plane_fb() does not.
This means the steps performed by intel_cleanup_plane_fb() aren't
balanced with with what was done intel_prepare_plane_fb() if there
is no fb for the plane. These hooks get called for every plane in
the state regardless of whether they have an fb or not.
Add a matching null obj check to intel_cleanup_plane_fb() to restore
the balance.
Note that intel_cleanup_plane_fb() has sufficient protections
already in place that the imbalance doesn't cause any real problems.
But having things be in balance seems nicer anyway, and might help
avoid some surprises in the future.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Switch over to using explicit old/new planes states instead of
digging the old state out via plane->state. The main issue is that
plane->state will point to the uapi state which we generally don't
even want to look at.
Also it sets a bad example as using plane->state during commit_tail()
would be a bug. Here we're still holding the modeset locks so it's
actually safe, but best not give people bad ideas.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Let's do the intel_plane_copy_uapi_to_hw_state() before we bail out
due to both old and new uapi.crtc being NULL. This will drop the
reference to the old hw.fb for planes that are transitioning from
being a slave plane to simply being disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Despite the fact that the VBT appears to have a field for specifying
that a system is equipped with a panel that supports standard VESA
backlight controls over the DP AUX channel, so far every system we've
spotted DPCD backlight control support on doesn't actually set this
field correctly and all have it set to INTEL_BACKLIGHT_DISPLAY_DDI.
While we don't know the exact reason for this VBT misuse, talking with
some vendors indicated that there's a good number of laptop panels out
there that supposedly support both PWM backlight controls and DPCD
backlight controls as a workaround until Intel supports DPCD backlight
controls across platforms universally. This being said, the X1 Extreme
2nd Gen that I have here (note that Lenovo is not the hardware vendor
that informed us of this) PWM backlight controls are advertised, but
only DPCD controls actually function. I'm going to make an educated
guess here and say that on systems like this one, it's likely that PWM
backlight controls might have been intended to work but were never
really tested by QA.
Since we really need backlights to work without any extra module
parameters, let's take the risk here and rely on the standard DPCD caps
to tell us whether AUX backlight controls are supported or not. We still
check the VBT, just so we can print a debugging message on systems that
advertise DPCD backlight support on the panel but not in the VBT.
Changes since v3:
* Print a debugging message if we enable DPCD backlight control on a
device which doesn't report DPCD backlight controls in it's VBT,
instead of warning on custom panel backlight interfaces.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112376
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Perry Yuan <pyuan@redhat.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200117232155.135579-1-lyude@redhat.com
Eliminate the inconsistencies in the hdcp code local variables:
- use dev_priv over dev
- use to_i915() instead of dev->dev_private
- initialize variables when declaring them
- a bit of declaration suffling to appease ocd
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-10-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Report port presence based on port presence in VBT alone, relaxing the
requirements on supported encoders (DP, DVI, or HDMI). The goal is to
make future changes easier, however there is a small risk of reporting
more ports present than before in case of dubious VBT.
Regarding the current callers of intel_bios_is_port_present(), the
potential issue might be caused by DVO_PORT_CRT being identified as port
E in dvo_port_to_port(). Hopefully no VBT has that on SKL+ which support
DP/DVI/HDMI on port E; the current CRT init code on HSW/BDW does not
care.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4338a29e4ed49e69f859dff1490fd85f6ae6177e.1579270868.git.jani.nikula@intel.com
Move the force_dvi check to a single function that can be called from
both mode validation and compute_config(). Note that currently we
don't call it from mode validation, but that will change soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The strings we want to print to the on stack buffers should
be no more than
8 * 3 + strlen("(GET_SCALED_HDTV_RESOLUTION_SUPPORT)") + 1 = 61
bytes. So let's shrink the buffers down to 64 bytes.
Also switch the BUG_ON()s to WARN_ON()s if I made a mistake in
my arithmentic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
sync_mode_slaves_mask is a bitmask so use PIPE_CONF_CHECK_X() for it
so we get the mismatch printed in hex instead of decimal.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115190813.17971-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Manasi Navare <manasi.d.navare@intel.com>
Let's use the pipe rather than the silly 'i' iterator from
for_each_oldnew_intel_crtc_in_state() for indexing the ddb
entries array. Maybe one day we can assume c99 and hide the
'i' entirely from sight.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115190813.17971-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently we don't call intel_crtc_prepare_cleared_state() for crtcs
that are going to be entirely disabled (uapi.enable==false). That
means such crtcs will leave stale junk lying around in their states
and we have to sprinkle hw.enable checks all over before we can
look at the states. Let's change that a bit so that we aways do
the state clearing, even for fully disabled crtcs.
Note that we still keep some parts of the old state (see
intel_crtc_prepare_cleared_state() for the details) so probably
can't trust things 100% when hw.enable==false. But at least there's
less chance now that we end up looking at stale junk.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115190813.17971-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The post-fastset "does anyone still need a full modeset?" for
port sync looks busted. The outer loop bails out of a full modeset
is still needed by the current crtc, and then we skip forcing
a full modeset on the related crtcs. That's totally the opposite
of what we want.
The MST path has the logic mostly the other way around so it
looks correct. To fix the port sync case let's follow the MST
logic for both. So, if the current crtc already needs a modeset
we do nothing. otherwise we check if any of the related crtcs
needs a modeset, and if so we force a full modeset for the
current crtc.
And while at let's change the else if to a plain if to so
we don't have needless coupling between the MST and port sync
checks.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Fixes: 05a8e45136 ("drm/i915/display: Use external dependency loop for port sync")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115190813.17971-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
For eDP panels, it appears it's expected that so long as the panel is in
DPCD control mode that the brightness value is never set to 0. Instead,
if the desired effect is to set the panel's backlight to 0 we're
expected to simply turn off the backlight through the
DP_EDP_DISPLAY_CONTROL_REGISTER.
We already do the latter correctly in intel_dp_aux_disable_backlight().
But, we make the mistake of writing the DPCD registers in the wrong
order when enabling the backlight in intel_dp_aux_enable_backlight()
since we currently enable the backlight through
DP_EDP_DISPLAY_CONTROL_REGISTER before writing the brightness level. On
the X1 Extreme 2nd Generation, this appears to have the potential of
confusing the panel in such a way that further attempts to set the
brightness don't actually change the backlight as expected and leave it
off. Presumably, this happens because the incorrect register writing
order briefly leaves the panel with DPCD mode enabled and a 0 brightness
level set.
So, reverse the order we write the DPCD registers when enabling the
panel backlight so that we write the brightness value first, and enable
the backlight second. This fix appears to be the final bit needed to get
the backlight on the ThinkPad X1 Extreme 2nd Generation's AMOLED screen
working.
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: Perry Yuan <pyuan@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200116211623.53799-4-lyude@redhat.com
Currently we always determine the initial panel brightness level by
simply reading the value from DP_EDP_BACKLIGHT_BRIGHTNESS_MSB/LSB. This
seems wrong though, because if the panel is not currently in DPCD
control mode there's not really any reason why there would be any
brightness value programmed in the first place.
This appears to be the case on the Lenovo ThinkPad X1 Extreme 2nd
Generation, where the default value in these registers is always 0 on
boot despite the fact the panel runs at max brightness by default.
Getting the initial brightness value correct here is important as well,
since the panel on this laptop doesn't behave well if it's ever put into
DPCD control mode while the brightness level is programmed to 0.
So, let's fix this by checking what the current backlight control mode
is before reading the brightness level. If it's in DPCD control mode, we
return the programmed brightness level. Otherwise we assume 100%
brightness and return the highest possible brightness level. This also
prevents us from accidentally programming a brightness level of 0.
This is one of the many fixes that gets backlight controls working on
the ThinkPad X1 Extreme 2nd Generation with optional 4K AMOLED screen.
Changes since v1:
* s/DP_EDP_DISPLAY_CONTROL_REGISTER/DP_EDP_BACKLIGHT_MODE_SET_REGISTER/
- Jani
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: Perry Yuan <pyuan@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200116211623.53799-3-lyude@redhat.com
Max backlight value for the panel was being calculated using byte
count i.e. 0xffff if 2 bytes are supported for backlight brightness
and 0xff if 1 byte is supported. However, EDP_PWMGEN_BIT_COUNT
determines the number of active control bits used for the brightness
setting. Thus, even if the panel uses 2 byte setting, it might not use
all the control bits. Thus, max backlight should be set based on the
value of EDP_PWMGEN_BIT_COUNT instead of assuming 65535 or 255.
Additionally, EDP_PWMGEN_BIT_COUNT was being updated based on the VBT
frequency which results in a different max backlight value. Thus,
setting of EDP_PWMGEN_BIT_COUNT is moved to setup phase instead of
enable so that max backlight can be calculated correctly. Only the
frequency divider is set during the enable phase using the value of
EDP_PWMGEN_BIT_COUNT.
This is based off the original patch series from Furquan Shaikh
<furquan@google.com>:
https://patchwork.freedesktop.org/patch/317255/?series=62326&rev=3
Changes since original patch:
* Remove unused intel_dp variable in intel_dp_aux_setup_backlight()
* Fix checkpatch issues
* Make sure that we rewrite the pwmgen bit count whenever we bring the
panel out of D3 mode
v2 by Jani:
* rebase
* fix readb return value check
Cc: Furquan Shaikh <furquan@google.com>
Tested-by: AceLan Kao <acelan.kao@canonical.com>
Tested-by: Perry Yuan <pyuan@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200116211623.53799-2-lyude@redhat.com
Perform the i2c bus/adapter lookup from ACPI Namespace only if ACPI is
enabled in the kernel config. If ACPI is not enabled or if the lookup
fails, we'll fallback to using the VBT for identifying the i2c bus.
v2: Add fixes tag (Jani)
Fixes: 8cbf89db29 ("drm/i915/dsi: Parse the I2C element from the VBT MIPI sequence block (v3)")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115012305.27395-1-vivek.kasireddy@intel.com
Both activate functions and the dc3co disable function were doing the
same thing, so better move to a function and share.
Also while at it adding a WARN_ON to catch invalid values.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113214603.52158-1-jose.souza@intel.com
fbc_supported() is just a pointless wrapper for HAS_FBC(). Get
rid of it. In places where we're operating on a specific plane
we can replace this with a plane->has_fbc check to avoid
doing anything for crtcs that don't even support fbc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of dealing with the presence/absence of the primary
plane in the higher level pre/post plane update code let's
move all that into the fbc code itself. Now the higher level
code doesn't have to think about FBC details anymore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Final drm/i915 features for v5.6:
- DP MST fixes (José)
- Fix intel_bw_state memory leak (Pankaj Bharadiya)
- Switch context id allocation to xarray (Tvrtko)
- ICL/EHL/TGL workarounds (Matt Roper, Tvrtko)
- Debugfs for LMEM details (Lukasz Fiedorowicz)
- Prefer platform acronyms over codenames in symbols (Lucas)
- Tiled and port sync mode fixes for fbdev and DP (Manasi)
- DSI panel and backlight enable GPIO fixes (Hans de Goede)
- Relax audio min CDCLK requirements on non-GLK (Kai Vehmanen)
- Plane alignment and dimension check fixes (Imre)
- Fix state checks for PSR (José)
- Remove ICL+ clock gating programming (José)
- Static checker fixes around bool usage (Ma Feng)
- Bring back tests for self-contained headers in i915 (Masahiro Yamada)
- Fix DP MST disable sequence (Ville)
- Start converting i915 to the new drm device based logging macros (Wambui Karuga)
- Add DSI VBT I2C sequence execution (Vivek Kasireddy)
- Start using function pointers and ops structs in uc code (Michal)
- Fix PMU names to not use colons or dashes (Tvrtko)
- TGL media decompression support (DK, Imre)
- Split i915_gem_gtt.[ch] to more manageable chunks (Matthew Auld)
- Create dumb buffers in LMEM where available (Ram)
- Extend mmap support for LMEM (Abdiel)
- Selftest updates (Chris)
- Hack bump up CDCLK on TGL to avoid underruns (Stan)
- Use intel_encoder and intel_connector more instead of drm counterparts (Ville)
- Build error fixes (Zhang Xiaoxu)
- Fixes related to GPU and engine initialization/resume (Chris)
- Support for prefaulting discontiguous objects (Abdiel)
- Support discontiguous LMEM object maps (Chris)
- Various GEM and GT improvements and fixes (Chris)
- Merge pinctrl dependencies branch for the DSI GPIO updates (Jani)
- Backmerge drm-next for new logging macros (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87sgkil0v9.fsf@intel.com
TGL has now a table for RBR and HBR and another table for HBR2 over
combo phys. The HBR2 one has some small changes comparing to the ICL
one, so adding two new tables and adding a function to return TGL
combo phy tables.
v2:
- reordered the tgl_combo_phy_ddi_translations_dp_hbr2 to reduce diff
(Matt)
- removed definition of rates, kept using raw number(Jani and Ville)
- changed code to use icl_get_combo_buf_trans() for non-DP as those
are equal between TGL and ICL(Matt)
BSpec: 49291
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110233902.154960-1-jose.souza@intel.com
intel_prepare_plane_fb() will always pin plane_state->hw.fb whenever
it is present. We copy that from the master plane to the slave plane,
but we fail to copy the corresponding ggtt view. Thus when it comes time
to pin the slave plane's fb we use some stale ggtt view left over from
the last time the plane was used as a non-slave plane. If that previous
use involved 90/270 degree rotation or remapping we'll try to shuffle
the pages of the new fb around accordingingly. However the new
fb may be backed by a bo with less pages than what the ggtt view
rotation/remapped info requires, and so we we trip a GEM_BUG().
Steps to reproduce on icl:
1. plane 1: whatever
plane 6: largish !NV12 fb + 90 degree rotation
2. plane 1: smallish NV12 fb
plane 6: make invisible so it gets slaved to plane 1
3. GEM_BUG()
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/951
Fixes: 1f594b209f ("drm/i915: Remove special case slave handling during hw programming, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110183228.8199-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
There seems to be some undocumented bandwidth
bottleneck/dependency which scales with CDCLK,
causing FIFO underruns when CDCLK is too low,
even when it's correct from BSpec point of view.
Currently for TGL platforms we calculate
min_cdclk initially based on pixel_rate divided
by 2, accounting for also plane requirements,
however in some cases the lowest possible CDCLK
doesn't work and causing the underruns.
We've found experimentally that raising cdclk to
at least pixel_rate (rather than pixel_rate/2)
eliminates these underruns, so let's use this as a
temporary workaround until the hardware team
can suggest a more precise remedy.
Explicitly stating here that this seems to be currently
rather a Hack, than final solution.
v2: Use clamp operation instead of min(Matt Roper)
v3: - Fixed commit message(Matt Roper)
- Now using pixel_rate instead of max_cdclk(Jani Nikula)
- Switched to max from clamp(Ville Syrjälä)
Hopefully this hybrid satisfies everyone :)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200109220547.23817-1-stanislav.lisovskiy@intel.com
Not every platform needs quirk detection for panel orientation, so
split the drm_connector_init_panel_orientation_property into two
functions. One for platforms without the need for quirks, and the
other for platforms that need quirks.
Hans de Goede (changes in v2):
Rename the function from drm_connector_init_panel_orientation_property
to drm_connector_set_panel_orientation[_with_quirk] and pass in the
panel-orientation to set.
Beside the rename, also make the function set the passed in value
only once, if the value was set before (to a value other then
DRM_MODE_PANEL_ORIENTATION_UNKNOWN) make any further set calls a no-op.
This change is preparation for allowing the user to override the
panel-orientation for any connector from the kernel commandline.
When the panel-orientation is overridden this way, then we must ignore
the panel-orientation detection done by the driver.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200105155120.96466-1-hdegoede@redhat.com
Parsing the i2c element is mainly done to transfer the payload from the
MIPI sequence block to the relevant slave device. In some cases, the
commands that are part of the payload can be used to turn on the backlight.
This patch is actually a refactored version of this old patch:
https://lists.freedesktop.org/archives/intel-gfx/2014-December/056897.html
In addition to the refactoring, the original patch is augmented by
looking up the i2c bus from ACPI NS instead of relying on the bus number
provided in the VBT.
This patch was tested on Aava Mobile's Inari 10 tablet. It enabled
turning on the backlight by transferring the payload to the device.
v2:
- Add DRM_DEV_ERROR for invalid adapter and failed transfer and also
drop the DRM_DEBUG that existed originally. (Hans)
- Add two gotos instead of one to clean things up properly.
v3:
- Identify the device on which this patch was tested in the commit
message (Ville)
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110181123.14536-1-vivek.kasireddy@intel.com
[why]
For DSC case we cannot use topology manager's PBN divider
variable. The default divider does not take FEC into account.
Therefore the driver has to calculate its own divider based
on the link rate and lane count its handling, as it is hw specific.
[how]
Pass pbn_div as an argument, which is used if its more than
zero, otherwise default topology manager's pbn_div will be used.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With DSC, bpp can be fractional in multiples of 1/16.
Change drm_dp_calc_pbn_mode to reflect this, adding a new
parameter bool dsc. When this parameter is true, treat the
bpp parameter as having units not of bits per pixel, but
1/16 of a bit per pixel
v2: Don't add separate function for this
v3: In the equation divide bpp by 16 as it is expected
not to leave any remainder
v4: Added DSC test parameters for selftest
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed a few assert_pipe_disabled() cases when changing it to
take enum transcoder instead of enum pipe, making sparse unhappy.
Convert the leftovers.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108145616.7349-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When moving the pipe disable & co. function calls from
haswell_crtc_disable() into the encoder .post_disable() hooks I
neglected to account for the MST vs. DDI interactions properly.
This now leads us to call these functions two times for the last
MST stream (once from the MST code and a second time from the DDI
code). The calls from the DDI code should only be done for SST
and not MST. Add the proper check for that.
This results in an MCE on ICL. My vague theory is that we turn off
the transcoder clock from the MST code and then we proceed to touch
something in the DDI code which still depends on that clock causing
the hardware to become upset. Though I can't really explain why
Stan's hack of omitting the pipe disable in the MST code would avoid
the MCE since we should still be turning off the transcoder clock.
But maybe there's something magic in the hw that keeps the clock on
as long as the pipe is on. Or maybe the clock isn't the problem and
we now touch something in the DDI disable code that really does need
the pipe to be still enabled.
v2: Rebase to latest drm-tip
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reported-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/901
Fixes: 773b4b5435 ("drm/i915: Move stuff from haswell_crtc_disable() into encoder .post_disable()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108144550.29280-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Fixes coccicheck warning:
drivers/gpu/drm/i915/display/intel_crt.c:1066:1-28: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/display/intel_crt.c:928:2-29: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/display/intel_crt.c:443:2-29: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1578013959-31486-4-git-send-email-mafeng.ma@huawei.com
Fixes coccicheck warning:
drivers/gpu/drm/i915/display/intel_dp.c:4950:1-33: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/display/intel_dp.c:4906:1-33: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1578013959-31486-3-git-send-email-mafeng.ma@huawei.com
Talked with HW team and this is a left over, driver should not
program clockgating, mg or dekel firmware is reponsible for any
clockgating programing.
Also removing the register and bits definition related to clockgating.
v2:
Added WARN_ON
v3:
Only calling icl_phy_set_clock_gating() on intel_ddi_pre_enable_hdmi
for GEN11
v4:
ICL should also not program clockgating (thanks Matt for catching
this)
BSpec issue: 20885
BSpec: 49292
BSpec: 21735
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107170922.153612-1-jose.souza@intel.com
Recent improvements in the state tracking in i915 caused PSR to not be
enabled when reusing firmware/BIOS modeset, this is due to all initial
commits returning ealier in intel_atomic_check() as needs_modeset()
is always false.
To fix that here forcing the state compute phase in CRTC that is
driving the eDP that supports PSR once. Enable or disable PSR do not
require a fullmodeset, so user will still experience glitch free boot
process plus the power savings that PSR brings.
It was tried to set mode_changed in intel_initial_commit() but at
this point the connectors are not registered causing a crash when
computing encoder state.
v2:
- removed function return
- change arguments to match intel_hdcp_atomic_check
v3:
- replaced drm includes in intel_psr.h by forward declaration(Jani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112253
Reported-by: <s.zharkoff@gmail.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200106152128.195171-1-jose.souza@intel.com
This loop was added directly to intel_atomic_check() to be used by
all other features that have external pipe dependencies, so using it
and removing intel_atomic_check_synced_crtcs().
After this changes is_trans_port_sync_master() it not used anywhere,
so removing it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200106142823.145260-1-jose.souza@intel.com
There is a cut and paste bug so we return the wrong error code.
Fixes: a603f5bd16 ("drm/i915/dp: Make sure all tiled connectors get added to the state with full modeset")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107130322.gdk5b6jurifr26c2@kili.mountain
Detect the modifier corresponding to media compression to enable
display decompression for YUV and xRGB packed formats. A new modifier is
added so that the driver can distinguish between media and render
compressed buffers. Unlike render decompression, plane 6 and plane 7 do not
support media decompression.
v2: Fix checkpatch warnings on code style (Lucas)
From DK:
Separate modifier array for planes that cannot decompress media (Ville)
v3: Support planar formats
v4: Switch plane order
v5:
- Use format block descriptors to get CCS subsampling calculation right
everywhere.
- Extend the plane state normal view array to accommodate 4 color planes.
- Use helpers to convert between main and CCS planes.
v6: Add missing packed YUV formats to the MC format list. (Yang)
v7: Align UV planes to tile-row size.
Cc: Nanley G Chery <nanley.g.chery@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Yang A Shi <yang.a.shi@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231233756.18753-8-imre.deak@intel.com
As intel_fb_plane_get_subsampling() returns the subsampling factor wrt.
its main plane, for a CCS plane we need to apply both the main and the
CCS plane's subsampling factor on the FB's dimensions to get the CCS
plane's dimensions.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231233756.18753-5-imre.deak@intel.com
Print a debug message if the FB plane[0] offset is not 0 as expected, to
help understainding an add FB IOCTL fail.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231233756.18753-4-imre.deak@intel.com
Currently the GGTT offset of a UV plane in a semiplanar YUV FB is tile
size (4kB) aligned. I noticed, that enforcing only this alignment leads
oddly to random memory corruptions on TGL while scanning out Y-tiled
FBs. This issue can be easily reproduced with a UV plane offset that is
not aligned to the plane's tile row size.
Some experiments showed the correct alignment to be tile row size
indeed. This also makes sense, since the de-tiling fence created for the
object - with its own stride and so "left" and "right" edge - applies to
all the planes in the FB, so each tile row of all planes should be tile
row aligned.
In fact BSpec requires this alignment since SKL. On SKL we may enforce
this due to the AUX plane x,y coords check, but on ICL and TGL we don't.
For now enforce this only on TGL; I can follow up with any necessary
change for ICL after more tests.
BSpec requires a stricter alignment for linear UV planes too (kind of a
tile row alignment), but it's unclear whether that's really needed
(couldn't be explained with the de-tiling fence as above) and enforcing
that could break existing user space; so avoid that too for now until
more tests.
v2:
- Clarify the commit log wrt. the address space the alignment applies to.
(Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231233756.18753-3-imre.deak@intel.com
At least one framebuffer plane on TGL - the UV plane of YUV semiplanar
FBs - requires a non-power-of-2 alignment, so add support for this. This
new alignment restriction applies only to an offset within an FB, so the
GEM buffer itself containing the FB must still be power-of-2 aligned.
Add a check for this (in practice plane 0, since the plane 0 offset must
be 0).
v2:
- Fix WARN check for alignment=0.
v3:
- Return error for alignment programming bugs. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231233756.18753-2-imre.deak@intel.com
Revert changes done in commit f6ec948309 ("drm/i915: extend audio
CDCLK>=2*BCLK constraint to more platforms"). Audio drivers
communicate with i915 over HDA bus multiple times during system
boot-up and each of these transactions result in matching
get_power/put_power calls to i915, and depending on the platform,
a modeset change causing visible flicker.
GLK is the only platform with minimum CDCLK significantly lower
than BCLK, and thus for GLK setting a higher CDCLK is mandatory.
For other platforms, minimum CDCLK is close but below 2*BCLK
(e.g. on ICL, CDCLK=176.4kHz with BCLK=96kHz). Spec-wise the constraint
should be set, but in practise no communication errors have been
reported and the downside if set is the flicker observed at boot-time.
Revert to old behaviour until better mechanism to manage
probe-time clocks is available.
The full CDCLK>=2*BCLK constraint is still enforced at pipe
enable time in intel_crtc_compute_min_cdclk().
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/913
Fixes: f6ec948309 ("drm/i915: extend audio CDCLK>=2*BCLK constraint to more platforms")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231140007.31728-1-kai.vehmanen@linux.intel.com
On Bay Trail devices the MIPI power on/off sequences for DSI LCD panels
do not control the LCD panel- and backlight-enable GPIOs. So far, when
the VBT indicates we should use the SoC for backlight control, we have
been relying on these GPIOs being configured as output and driven high by
the Video BIOS (GOP) when it initializes the panel.
This does not work when the device is booted with a HDMI monitor connected
as then the GOP will initialize the HDMI instead of the panel, leaving the
panel black, even though the i915 driver tries to output an image to it.
Likewise on some device-models when the GOP does not initialize the DSI
panel it also leaves the mux of the PWM0 pin in generic GPIO mode instead
of muxing it to the PWM controller.
This commit makes the DSI code control the SoC GPIOs for panel- and
backlight-enable on BYT, when the VBT indicates the SoC should be used
for backlight control. It also ensures that the PWM0 pin is muxed to the
PWM controller in this case.
This fixes the LCD panel not lighting up on various devices when booted
with a HDMI monitor connected. This has been tested to fix this on the
following devices:
Peaq C1010
Point of View MOBII TAB-P800W
Point of View MOBII TAB-P1005W
Terra Pad 1061
Yours Y8W81
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-6-hdegoede@redhat.com
Move the Crystal Cove PMIC panel GPIO lookup-table from
drivers/mfd/intel_soc_pmic_core.c to the i915 driver.
The moved looked-up table is adding a GPIO lookup to the i915 PCI
device and the GPIO subsys allows only one lookup table per device,
The intel_soc_pmic_core.c code only adds lookup-table entries for the
PMIC panel GPIO (as it deals only with the PMIC), but we also need to be
able to access some GPIOs on the SoC itself, which requires entries for
these GPIOs in the lookup-table.
Since the lookup-table is attached to the i915 PCI device it really
should be part of the i915 driver, this will also allow us to extend
it with GPIOs from other sources when necessary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-5-hdegoede@redhat.com
When the LCD has not been turned on by the firmware/GOP, because e.g. the
device was booted with an external monitor connected over HDMI, we should
not turn on the panel-enable GPIO when we request it.
Turning on the panel-enable GPIO when we request it, means we turn it on
too early in the init-sequence, which causes some panels to not correctly
light up.
This commits adds a panel_is_on parameter to intel_dsi_vbt_gpio_init()
and makes intel_dsi_vbt_gpio_init() set the initial GPIO value accordingly.
This fixes the panel not lighting up on a Thundersoft TST168 tablet when
booted with an external monitor connected over HDMI.
Changes in v2:
- Call intel_dsi_get_hw_state() to check if the panel is on instead of
relying on the current_mode pointer
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-4-hdegoede@redhat.com
On some older devices (BYT, CHT) which may use v2 VBT MIPI-sequences,
we need to manually control the panel enable GPIO as v2 sequences do
not do this.
So far we have been carrying the code to do this on BYT/CHT devices
with a Crystal Cove PMIC in vlv_dsi.c, but as this really is a shortcoming
of the VBT MIPI-sequences, intel_dsi_vbt.c is a better place for this,
so move it there.
This is a preparation patch for adding panel-enable and backlight-enable
GPIO support for BYT devices where instead of the PMIC the SoC is used
for backlight control.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-3-hdegoede@redhat.com
I implemented a small build rule in drivers/gpu/drm/i915/Makefile
without relying on the special header-test-y syntax that was removed in
commit fcbb8461fd ("kbuild: remove header compile test").
I excluded some headers from the test coverage. I hope somebody
intrested can take a closer look at them.
Dummy subdir Makefiles can be removed altogether as single target build
use case is now covered by commit 394053f4a4 ("kbuild: make single
targets work more correctly").
v2 by Jani:
- add selftests/i915_perf_selftests.h to no-header-test
- add .gitignore for *.hdrtest
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219155652.2666-3-jani.nikula@intel.com
While clearing the Ports ync mode enable and master select bits
we need to clear the register completely instead of using disable masks
v3:
* Remove reg variable (Matt)
v2:
* Just write 0 to the reg (Ville)
* Rebase
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 51528afe7c ("drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-3-manasi.d.navare@intel.com
Add an extra check before making master slave assignments for tiled
displays to make sure we make these assignments only if all tiled
connectors are present. If not then initialize the state to defaults
so it does a normal non tiled modeset without transcoder port sync.
v4:
deafulat port sync values in prepare_cleared_state (Ville)
v3:
* Default master trans to INVALID to avoid pipe mismatch
v2:
* Rename icl_add_sync_mode_crtcs
* Move this function just before .compute_config hook
* Check if DP before master slave assignments (Ville)
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-2-manasi.d.navare@intel.com
In case of tiled displays, all the tiles are linke dto each other
for transcoder port sync. So in intel_atomic_check() we need to make
sure that we add all the tiles to the modeset and if one of the
tiles needs a full modeset then mark all other tiles for a full modeset.
We also need to force modeset for all synced crtcs after fastset check.
v6:
* Add comments about why we do not call
drm_atomic_helper_check_modeset (Matt)
* Add FIXME for a corner case where tile info might vanish (Matt)
v5:
* Rebase
v4:
* Fix logic for modeset_synced_crtcs (Ville)
v3:
* Add tile checks only for Gen >11
v2:
* Change crtc_state scope, remove tile_grp_id (Ville)
* Use intel_connector_needs_modeset() (Ville)
* Add modeset_synced_crtcs (Ville)
* Make sure synced crtcs are forced full modeset
after fastset check (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-1-manasi.d.navare@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts ivybridge to ivb where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-9-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts broadwell to bdw where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-8-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts ironlake to ilk where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-7-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts icelake to icl where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-6-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts cannonlake to cnl where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-5-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts skylake to skl where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-4-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts haswell to hsw where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-3-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts pineview to pnv where appropriate.
v2: Add missing conversions in intel_pm.c (Matt Roper). While at it, fix
missing blank lines between structs that would otherwise trigger
checkpatch errors (Lucas)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-2-lucas.demarchi@intel.com
WaDisableDARBFClkGating, now known as Wa_14010480278, has been added to
the workaround tables for ICL, EHL, and TGL so we need to extend our
platform test accordingly.
Bspec: 33450
Bspec: 33451
Bspec: 52890
Cc: stable@kernel.vger.org
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224012026.3157766-2-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
This function is only called from port sync and it is identical to
what will be executed again in intel_update_crtc() over port sync
pipes.
If it is really necessary at least it deserves a better name and a
comment, leaving it to people working on port sync.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-7-jose.souza@intel.com
MST master can not be disabled while it have attached MST slaves, so
it is necessary force a modeset in all of its slaves.
v3:
- moved handling to intel_atomic_check() this way is guarantee that
all pipes will have its state computed
v4:
- added a function to return if MST master neeeds modeset to simply
code in intel_atomic_check()
v5:
- fixed and moved code to check if MST master needs a modeset
v6:
- previons version of this patch was split into two patches
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-6-jose.souza@intel.com
MST and port sync have master and slaves pipes and it brings
dependencies between pipes to allow fastset.
For example if only MST master needs a modeset all of its slaves also
needs to do a modeset.
This patch adds the base for external dependencies check, the MST and
port sync bits will be added in another patches.
v3:
- moved handling to intel_atomic_check() this way is guarantee that
all pipes will have its state computed
v4:
- added a function to return if MST master neeeds modeset to simply
code in intel_atomic_check()
v5:
- fixed and moved code to check if MST master needs a modeset
v6:
- previons version of this patch was split into two patches
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-5-jose.souza@intel.com
The disable sequence after wait for transcoder off was not correctly
implemented.
The MST disable sequence is basically the same for HSW, SKL, ICL and
TGL, with just minor changes for TGL.
With this last patch we finally fixed the hotplugs triggered by MST
sinks during the disable/enable sequence, those were causing source
to try to do a link training while it was not ready causing CPU pipe
FIFO underrrus on TGL.
v2: Only unsetting TGL_TRANS_DDI_PORT_MASK for TGL on the post
disable sequence
v4: Rebased, moved MST sequences to intel_mst_post_disable_dp()
BSpec: 4231
BSpec: 4163
BSpec: 22243
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-4-jose.souza@intel.com
Due to DDB overlaps the pipe enabling sequence is not always crescent.
As the previous patch selects the smallest pipe/transcoder in the MST
stream to be master and it needs to be enabled first, this changes
were needed to guarantee that.
So first lets enable all pipes that do not need a fullmodeset as
those don't have any external dependency and those are the ones that
can overlap with each other.
Then on the second loop it will enable all the pipes that needs a
modeset and don't depends on other pipes like MST master
pipe/transcoder.
Then finally all the pipes that needs a modeset and have dependency
on other pipes, that at this point are alread enabled.
v3: rebased
v4:
- added check for modeset_pipes too to decide if is necessary for a
wait a vblank
- added DDB allocation overlap check for pipes that needs a modeset
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-3-jose.souza@intel.com
On TGL the blending of all the streams have moved from DDI to
transcoder, so now every transcoder working over the same MST port must
send its stream to a master transcoder and master will send to DDI
respecting the time slots.
So here adding all the CRTCs that shares the same MST stream if
needed and computing their state again, it will pick the lowest
pipe/transcoder among the ones in the same stream to be master.
Most of the time skl_commit_modeset_enables() enables pipes in a
crescent order but due DDB overlapping it might not happen, this
scenarios will be handled in the next patch.
v2:
- Using recently added intel_crtc_state_reset() to set
mst_master_transcoder to invalid transcoder for all non gen12 & MST
code paths
- Setting lowest pipe/transcoder as master, previously it was the
first one but setting a predictable one will help in future MST e
port sync integration
- Moving to intel type as much as we can
v3:
- Now intel_dp_mst_master_trans_compute() returns the MST master transcoder
- Replaced stdbool.h by linux/types.h
- Skip the connector being checked in
intel_dp_mst_atomic_master_trans_check()
- Using pipe instead of transcoder to compute MST master
v4:
- renamed connector_state to conn_state
v5:
- Improved the parameters of intel_dp_mst_master_trans_compute() to
simply code
- Added call drm_atomic_add_affected_planes() in
intel_dp_mst_atomic_master_trans_check() as helper could not do it
for us
- Removed "if (ret)" left over from v3 changes
v6:
- handled ret == I915_MAX_PIPES case in compute
BSpec: 50493
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-2-jose.souza@intel.com
intel_connector_needs_modeset() will be used outside of
intel_display.c in a future patch so it would only be necessary to
remove the state and add the prototype to the header file.
But while at it, I simplified the arguments and moved it to a better
place intel_atomic.c.
No behavior changes intended here.
v3:
- removed digital from exported version of intel_connector_needs_modeset
- rollback connector to drm type
v4:
- Renamed new_connector_state to new_conn_state
- Going back to drm_connector_state in
intel_encoders_update_prepare/complete as we also have
intel_tv_connector_state
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-1-jose.souza@intel.com
For CCS formats, the current DRM core check for YUV semiplanar formats
doesn't work; use an i915 specific function for that.
v2: Fix checkpatch warnings.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-11-imre.deak@intel.com
Y planes program the offset and stride of the AUX plane, so make sure we
copy the required info for this into their plane state.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-10-imre.deak@intel.com
During framebuffer creation, we pre-compute offsets for 90/270 plane
rotation. However, only Y and Yf modifiers support 90/270 rotation. So,
skip the calculations for other modifiers.
To keep the gem buffer size check still working for tiled planes, factor
out the logic needed for rotation setup and skip only this part for
tiled planes other than Y/Yf.
v2: Add a bounds check WARN for the rotation info array.
v3: Keep the gem buffer size check working for tiled planes.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-9-imre.deak@intel.com
The CCS plane stride must be fixed on TGL, as it's not configurable for
the display. Instead the HW has a hardwired logic to determine it from
the main plane stride. Make sure userspace passes in the correct stride.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-8-imre.deak@intel.com
Gen-12 display decompression operates on Y-tiled compressed main surface.
The CCS is linear and has 4 bits of metadata for each main surface cache
line pair, a size ratio of 1:256. Gen-12 display decompression is
incompatible with buffers compressed by earlier GPUs, so make use of a new
modifier to identify gen-12 compression. Another notable change is that
render decompression is supported on all planes except cursor and on all
pipes. Start by adding render decompression support for [A,X]BGR888 pixel
formats.
v2: Fix checkpatch warnings (Lucas)
v3:
Rebase, disable color clear, styling changes and modify
intel_tile_width_bytes and intel_tile_height to handle linear CCS
v4:
- Use format block descriptors and the i915 specific func to get the
subsampling for each color plane.
- Use helpers to convert between CCS and main planes.
v5:
- Fix subsampling returned by intel_fb_plane_get_subsampling() for
the CCS plane of the first plane.
v6:
- Rebased on v2 of patch 4.
v7:
- Fix plane dimensions during FB check.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Nanley G Chery <nanley.g.chery@intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> (v6)
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-7-imre.deak@intel.com
Using helpers instead of open coding this to select a CCS plane for a
main plane makes the code cleaner and less error-prone when the location
of CCS plane can be different based on the format (packed vs. YUV
semiplanar). The same applies to selecting an AUX plane which can be a
UV plane (for an uncompressed YUV semiplanar format), or a CCS plane.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-5-imre.deak@intel.com
intel_fill_fb_info() has grown quite large and wrapping the offset checks
into a separate function makes the loop a bit easier to follow.
v2: Skip the check for non-CCS planes. (Mika)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-4-imre.deak@intel.com
Easier to read if all the alignment changes are in one place and contained
within a function.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-3-imre.deak@intel.com
intel_tile_dims() computes tile height using size and width, when there
is already a function to do just that - intel_tile_height()
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191221120543.22816-2-imre.deak@intel.com
The power domain covers VDSC for DSI transcoder on ICL, and it's
pedantically about pipe, not transcoder, on TGL.
Reported-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219133845.9333-1-jani.nikula@intel.com
Begin pulling the GT setup underneath a single GT umbrella; let intel_gt
take ownership of its engines! As hinted, the complication is the
lifetime of the probed engine versus the active lifetime of the GT
backends. We need to detect the engine layout early and keep it until
the end so that we can sanitize state on takeover and release.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222120752.1368352-1-chris@chris-wilson.co.uk
We have several places where we want to allocate a pristine
crtc state. Some of those currently call intel_crtc_state_reset()
to properly initialize all the non-zero defaults in the state, but
some places do not. Let's add intel_crtc_state_alloc() to do both
the alloc and the reset, and call that everywhere we need a fresh
crtc state.
v2: s/kzalloc/kmalloc/ since we memset() anyway (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219111430.17527-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
All the other display related tracepoints use intel_ instead
if i915_ as the prefix. Do the same for the pipe update
tracepoints so I don't always have to spend time looking for
them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-6-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
I fumbled the conflict resolution a bit when applying the
fbc vblank wait w/a. Because of that we now call intel_fbc_pre_update()
twice. Remove the second redundant call.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
icl and tgl are still affected by the modulo 4 PLANE_OFFSET.y
underrun issue. Reject such configurations on all gen9+ platforms.
Can be reproduced easily with the following sequence of
hardware poking:
while {
write FBC_CTL.enable=1
wait for vblank
write PLANE_OFFSET .x=0 .y=32
write PLANE_SURF
wait for vblank
# if PLANE_OFFSET.y is multiple of 4 the underrun won't happen
write PLANE_OFFSET .x=0 .y=31
write PLANE_SURF
wait for vblank
# extra vblank wait is required here presumably
# to get FBC into the proper state
wait for vblank
write FBC_CTL.enable=0
# underrun happens some time after FBC disable
wait for vblank
}
Both 8888 and 565 pixel formats and all tilinga formats
seem affected. Reproduced on KBL/GLK/ICL/TGL. BDW confirmed
not affected.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/792
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently pointers to and from are not initialized and may contain
garbage values. This will cause uninitialized pointer reads in the
call to intel_frontbuffer_track and later checks to see if to and from
are null. Fix this by ensuring to and from are initialized to NULL.
Addresses-Coverity: ("Uninitialised pointer read)"
Fixes: da42104f58 ("drm/i915: Hold reference to intel_frontbuffer as we track activity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219190916.24693-1-colin.king@canonical.com
Fix several issues with DSC power domains that did not take DSI
transcoders into account:
- On TGL+ we need to use PW2 for DSC on pipe A, not transcoder A. There
is no longer an eDP transcoder, but there are two DSI transcoders
which may be connected to pipe A.
- On TGL+ we need to use the pipe, not transcoder, power domains for DSC
on pipes other than A. Again, there are DSI transcoders.
- On ICL we need to use PW2 for DSC also for DSI transcoders, not just
for the eDP transcoder.
Using is_pipe_dsc() also adds the warning about ICL pipe A DSC, which
does not exist.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212134728.18432-1-jani.nikula@intel.com
The check for cpu_transcoder != TRANSCODER_A is more magic than
necessary, and potentially misleading. Before TGL, DSC is supported on
pipe A if, and only if, it's used with eDP or DSI transcoders. No
functional changes.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f00e9d55ce20b256177222588780c660aa587cc3.1576081155.git.jani.nikula@intel.com
ICL eDP and DSI transcoders have a DSC engine separate from the
pipe. Abstract the register selection and fix it for ICL.
Add a warning for pipe A DSC on ICL; it does not exist.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/01bcddcdf397b1c8eb859ed18ebe023fb64383d9.1576081155.git.jani.nikula@intel.com
Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.
I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.
We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.
Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
To make life easier in the future let's pass the old crtc state
to intel_crtc_vblank_off() just like we already do for its
counterpart intel_crtc_vblank_on().
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
To make life easier in the future let's pass the old crtc state
to skylake_scaler_disable() just like we already do for
for its ancestor ironlake_pfit_disable().
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
HSW+ platforms call encoder .post_disable() and .post_pll_disable()
back to back. And since we don't even disable the PLL in between
let's just move everything into .post_disable().
intel_dp_mst does forward the .post_disable() call to intel_ddi at
the very end of its own .post_disable() hook, so this time MST
I shouldn't even break MST by accident.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Remove the pointless vfunc detour for hsw_fdi_link_train()
and just call it directly. Also pass the encoder in so we
can nuke the silly encoder loop within.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
For the sake of symmetry with the crtc stuff let's add
a helper to reset the plane state to sane default values.
For the moment this only gets caller from the plane init.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We have a few places where we want to reset a crtc state to its
default values. Let's add a helper for that. We'll need the new
__drm_atomic_helper_crtc_state_reset() helper for this to allow
us to just reset the state itself without clobbering the
crtc->state pointer.
And while at it let's zero out the whole thing, except a few
choice member which we'll mark as "invalid". And thanks to this
we can now nuke intel_crtc_init_scalers().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We already have alloc/free helpers for planes, add the same for
crtcs. The main benefit is we get to move all the annoying state
initialization out of the main crtc_init() flow.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Since obj->frontbuffer is no longer protected by the struct_mutex, as we
are processing the execbuf, it may be removed. Mark the
intel_frontbuffer as rcu protected, and so acquire a reference to
the struct as we track activity upon it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/827
Fixes: 8e7cb1799b ("drm/i915: Extract intel_frontbuffer active tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----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=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).
So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.
On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.
So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012
Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.
This commit fixes using the wrong PWM controller on these devices by
calling pwm_get() for the right PWM controller based on the
VBT dsi.config.pwm_blc bit.
Note this is part of a series which contains 2 other patches which renames
the PWM lookup for the 1st SoC/LPSS PWM from "pwm_backlight" to
"pwm_pmic_backlight" and the PWM lookup for the Crystal Cove PMIC PWM
from "pwm_backlight" to "pwm_pmic_backlight".
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-4-hdegoede@redhat.com
According to both the old acpi_igd_opregion_spec_0.pdf and the newer
skl_opregion_rev0p5.pdf opregion specification documents, if a driver
handles hotplug events itself, it should set the opregion CHPD field to
1 to indicate this and the firmware should respond to this by no longer
sending ACPI 0x00 notification events on e.g. lid-state changes.
Specifically skl_opregion_rev0p5.pdf states thid in the documentation of
the CHPD word: "Re-enumeration trigger logic in System BIOS MUST be
disabled for all the Operating Systems supporting Hot-Plug
(e.g., Windows* Longhorn and above)." Note the MUST in there.
We ignore these notifications, so this should not be a problem but many
recent DSTDs seem to all have the same copy-pasted bug in the GNOT() AML
function which is used to send these notifications. Windows likely does not
hit this bug as it presumably correcty sets CHPD to 1.
Here is an example of the broken GNOT() method:
Method (GNOT, 2, NotSerialized)
{
...
CEVT = Arg0
CSTS = 0x03
If (((CHPD == Zero) && (Arg1 == Zero)))
{
If (((OSYS > 0x07D0) || (OSYS < 0x07D6)))
{
Notify (PCI0, Arg1)
}
Else
{
Notify (GFX0, Arg1)
}
}
...
Notice that the condition for the If is always true I believe that the
|| like needs to be an &&, but there is nothing we can do about this and
in my own DSDT archive 55 of the 93 DSDTs have this issue.
When the if is true the notification gets send to the PCI root instead
of only to the GFX0 device. This causes Linux to re-enumerate PCI devices
whenever the LID opens / closes, leading to unexpected messages in dmesg:
Suspend through lid close:
[ 313.598199] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.664453] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.737982] pci_bus 0000:01: Allocating resources
[ 313.738036] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 313.738051] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[ 313.738111] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x91000000-0x911fffff 64bit pref]
[ 313.738128] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
Resume:
[ 813.623894] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[ 813.623955] pci 0000:00:03.0: reg 0x10: [mem 0x00000000-0x003fffff]
[ 813.630477] pci 0000:00:03.0: BAR 0: assigned [mem 0x91c00000-0x91ffffff]
[ 854.579101] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
And more importantly this re-enumeration races with suspend/resume causing
enumeration to not be complete when assert_isp_power_gated() from
drivers/gpu/drm/i915/display/intel_display_power.c runs. This causes
the !pci_dev_present(isp_ids) check in assert_isp_power_gated() to fail
making the condition for the WARN true, leading to:
[ 813.327886] ------------[ cut here ]------------
[ 813.327898] ISP not power gated
[ 813.328028] WARNING: CPU: 2 PID: 2317 at drivers/gpu/drm/i915/display/intel_display_power.c:4870 intel_display_print_error_state+0x2b98/0x3a80 [i915]
...
[ 813.328599] ---[ end trace f01e81b599596774 ]---
This commit fixes the unwanted ACPI notification on the PCI root device
by setting CHPD to 1, so that the broken if condition in the AML never
gets checked as notifications of type 0x00 are disabled altogether.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212204828.191288-1-hdegoede@redhat.com
Commit 4d89adc7b5 ("drm/i915/display/dsi: Add support to pipe D")
added pipe D support for DSI, but failed to update the state readout.
Fixes: 4d89adc7b5 ("drm/i915/display/dsi: Add support to pipe D")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211110844.2996-1-jani.nikula@intel.com
Just like in commit 523e0cc89b ("drm/i915/tgl: allow DVI/HDMI on port
A"), the port checks when reading the VBT can easily not match what the
platform really exposes. However here we only have some additional debug
messages that are not adding much value: in the previous debug message
we already print everything we know about the VBT.
Instead of keep fixing the possible port assignments according to the
platform, just nuke the additional messages.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206190552.8818-1-lucas.demarchi@intel.com
Now that the combo PHY aux power well handlers are used exclusively on
Icelake, we can drop a bunch of the extra tests.
v2: Don't try to use intel_uncore_rmw for register updates yet; there's
pending display uncore patches that need to land first. (Lucas)
v3: Drop the combo phy assertion. It was backward before, but doesn't
seem terribly necessary. I'm keeping the IS_ICELAKE assertion
though since we often copy/paste/modify the power well tables when
defining new platforms and it's too easy to cargo cult the
ICL-specific handling to new platforms that shouldn't use it.
(Lucas)
v4: Fix build; forgot to commit all the changes. (CI)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213010600.701315-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
The TGL workaround database no longer shows Wa #1178 (or anything
similar under different workaround names/numbers) so we should be able
to drop it. In fact Swati just discovered that applying this workaround
is the root cause of some power well enable failures we've been seeing
in CI (gitlab issue 498).
Once we stop applying this WA, TGL no longer utilizes any of the special
handling provided by icl_combo_phy_aux_power_well_ops so we can just
drop back to using the standard hsw-style power well ops instead.
v3: Drop now-unused _TGL_AUX_ANAOVRD1_C definition too. (Lucas)
Closes: https://gitlab.freedesktop.org/drm/intel/issues/498
Fixes: deea06b475 ("drm/i915/tgl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-3-matthew.d.roper@intel.com
Outputs C and D on EHL are combo PHY outputs and thus should not be
using the same TC AUX power well handlers as ICL. And even though
icl_combo_phy_aux_power_well_ops works okay for EHL/JSL combo PHYs none
of its special handling is actually necessary for this platform:
* EHL/JSL don't actually need to program PORT_CL_DW12
* Display WA #1178 does not apply to EHL/JSL
Thus we can simply drop back to using our standard "hsw-style" power
well ops for EHL AUX power wells.
Bspec: 4301
Fixes: f722b8c1e2 ("drm/i915/ehl: All EHL ports are combo phys")
Cc: Jose Souza <jose.souza@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-2-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
The "num_dtd" variable is the number of elements in the
generic_dtd->dtd[] array so the > needs to be >= to prevent reading one
element beyond the end of the array.
Fixes: 33ef6d4fd8 ("drm/i915/vbt: Handle generic DTD block")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212091130.zf2g53njf5u24wk6@kili.mountain
skl_commit_modeset_enables() is a bit of mess. Let's streamline
it by simply tracking which pipes still need to be updated.
As a bonus we get rid of the state->wm_results.dirty_pipes usage.
v2: Rebase due to port sync
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210144105.3239-2-ville.syrjala@linux.intel.com
In order to eliminate intel_pipe_to_cpu_transcoder() (and its
crtc->config usage) let's pass the cpu transcoder to
assert_pipe() so we don't have to do the pipe->cpu transcoder
lookup on HSW+.
On VLV/CHV this can get called during eDP init, which
happens before crtc->config->cpu_transcoder is even
populated. So currently we're always reading PIPECONF(A)
there even if we're trying to check the state of some
other pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112163812.22075-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Let's start to eliminate intel_pipe_to_cpu_transcoder() so that
we can get rid of one more crtc->config usage (which we will want
to nuke as well).
In the case of assert_fdi_tx() we know that we're never
dealing with the EDP transcoder so we can simply replace
this with a cast.
v2: Fix poor English in comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112163812.22075-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Enable DSC for DSI, if specified in VBT.
This still lacks DSC aware get config implementation, and therefore
state checker will fail. Also mode valid is not there yet.
v5:
- add dsc get config call
v4:
- convert_rgb = true (Vandita)
- ignore max cdclock check (Vandita)
- rename pipe_config to crtc_state
v3:
- take compressed bpp into account
v2:
- Nuke conn_state->max_requested_bpc, it's not used on DSI
Bspec: 49263
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e0136299e03c582238523189f6951eeb08daed98.1575974743.git.jani.nikula@intel.com
When DSC is enabled, we need to adjust the horizontal timings to account
for the compressed (and therefore reduced) link speed.
The compressed frequency ratio simplifies down to the ratio between
compressed and non-compressed bpp.
Bspec: 49263
Suggested-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fecebdc2719dd0c78eaf8f4d3225bb185956d7db.1575974743.git.jani.nikula@intel.com
We'll be expanding afe_clk() to take DSC into account. Switch to using
it where DSC matters. Which is really everywhere that
intel_dsi_bitrate() is currently used in ICL DSI code.
The functional difference is that we round the result closest instead of
down.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b6c52b320daa8aaa0d79618ce714170f8f04ff67.1575974743.git.jani.nikula@intel.com
Add basic hardware state readout for DSC, and check the most relevant
details in the state checker.
v2:
- check for DSC power before reading its state
- check if source supports DSC at all
As a side effect, this should also get the power domains for the enabled
DSC on takeover, and subsequently disable DSC if it's not needed.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3fb018cf9bd9a4c275aab389b6ec0f2a4e938bb9.1575974743.git.jani.nikula@intel.com
Move intel_dp_source_supports_dsc() from intel_dp.c as
intel_dsc_source_support() in intel_vdsc.c. The DSC source support is
more about DSC than about DP, and will be needed for DP independent
code.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c9f646090913290fb00efd46a4332421bf95930.1575974743.git.jani.nikula@intel.com
Add DSI specific computation and transmission to display of PPS.
With hopes that this approach will work for both DP and DSI encoders.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/461db10b1f4d76625625a9f2b1e3d932fff42799.1575974743.git.jani.nikula@intel.com
Turns out future DSI specific parameters aren't workable with the
approach of having the encoder specific functions in intel_vdsc.c. Make
intel_dsc_compute_params() a helper that does the encoder independent
parts, and have encoder code call it. Move intel_dsc_dp_compute_params()
to intel_dp.c as intel_dp_dsc_compute_params().
No functional changes.
v2: Rename pipe_config to crtc_state while at it.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/620688ec302f7f49cc539c6c1653bfaf6092fce0.1575974743.git.jani.nikula@intel.com
Add function for retrieving the DSC data for an encoder.
Initially, this is DSI specific, as DP does not use VBT settings for DSC
at all. It's also not very pretty.
In the future we might have a pointer from encoder to the child device,
which would make the child device list query here so much more sensible.
v3:
- use crtc_state instead of pipe_config
- return true by default from intel_bios_get_dsc_params()
- expand the comment about rc_buffer_block_size and rc_buffer_size
v2:
- make more robust, debug log errors better
Bspec: 29885
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b895c349d964d70e4cad26f12a629ea1898bfcc2.1575974743.git.jani.nikula@intel.com
Check for child devices that specify compression, and store the device
specific compression parameters in the display device data struct for
later use. Warn if compression is requested but not available.
Use fairly rigid checks for compression data for starters. These can be
made more dynamic later.
Log about DSC presence in DDI port parse, though this is not universal
across platforms or port types (DSI).
v2: amended debug logging
Bspec: 29885
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/357d685ba047faf2285138c2f7014a8dee9a12b7.1575974743.git.jani.nikula@intel.com
Gen12 can improve bandwidth efficiency by pairing up memory requests
with similar addresses. We need to program the BW_BUDDY1 and BW_BUDDY2
registers according to the memory configuration during display
initialization to take advantage of this capability.
The magic numbers we program here feel like something that could
definitely change on future platforms, so let's use a table-based
programming scheme to make this easy to extend in the future.
v2:
- Add separate table for Wa_1409767108. (Stan)
- Reorder structure reduce size by a word. Page mask can still be up
to 28 bits (even though current values are small) so we should keep
it as a u32, but just using a u8 for DRAM type instead of the actual
enum type saves space. (Lucas, Ville)
- Rename function to tgl_bw_buddy_init() to be more precise about what
it does. (Lucas)
Bspec: 49189
Bspec: 49218
Bspec: 52890
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205224848.76712-1-matthew.d.roper@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
(cherry picked from commit 67e1d5ed85)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We're missing a workaround in the fbc code for all glk+ platforms
which can cause corruption around the top of the screen. So
enabling fbc by default is a bad idea. I'm not keen to backport
the w/a so let's start by disabling fbc by default on all glk+.
We'll lift the restriction once the w/a is in place.
Cc: stable@vger.kernel.org
Cc: Daniel Drake <drake@endlessm.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit cd8c021b36)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The code assumes we can omit the cfb allocation once fbc
has been enabled once. That's nonsense. Let's try to
reallocate it if we need to.
The code is still a mess, but maybe this is enough to get
fbc going in some cases where it initially underallocates
the cfb and there's no full modeset to fix it up.
Cc: Daniel Drake <drake@endlessm.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-15-ville.syrjala@linux.intel.com
Tested-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Now that we have the glk+ w/a for back to back fbc disable + plane
update in place we can once more enable fbc on glk+ by default.
Cc: Daniel Drake <drake@endlessm.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-14-ville.syrjala@linux.intel.com
Tested-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
On glk+ the hardware gets confused if we disable FBC while
it's recompressing and we perform a plane update during the
same frame. The result is that top of the screen gets corrupted.
We can avoid that by giving the hardware enough time to finish
the FBC disable before we touch the plane registers. Ie. we need
an extra vblank wait after FBC disable.
v2: Don't do the vblank wait if we never activated FBC in hw
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128150338.12490-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The hardware automagically nukes the cfb on flip. We can use
that whenever the plane/crtc configuration doesn't change too
much. Let's hook that up.
We'll need this for glk+ since we need to introduce an extra
vblank wait after FBC disable. As we're currently disabling
FBC around all plane updates we'd slow them down by an extra
frame. Not a great user experience when your fps is always
capped at vrefres/2. With flip nuke we don't need the extra
vblank wait.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-12-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
i965gm no longer needs the fence for scanout so we should be
do what we do for ctg+ and only configure a fence for FBC
when we have one.
In theory this should do nothing atm on account of
intel_fbc_can_activate() requiring the fence, but since
we do this for g4x+ let's do it for i965gm as well. We
may want to relax the requirements at some point and allow
FBC without a fence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-9-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Precompute the override cfb stride value so that we can check
it when determining if flip nuke can be used or not.
The hardware has 13 bits for this, so we can shrink the storage
to u16 while at it.
v2: Don't explode when crtc_state->enable_fbc lies to us
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We don't want to use the FBC hardware render tracking so let's not
enable it. To use the hw tracking properly we'd anyway need to
integrate this into the command submissing path as the register is
context saved, and if rendering happens via the ppgtt we'd have
to configure it with the ppgtt address instead of the ggtt address.
Easier to use software tracking instead.
Note that on pre-ilk we can't actually disable render tracking.
However we can't rely on it because it requires that DSPSURF to
match the render target address, and since we play tricks
with DSPSURF that may not be the case. Hence we shall rely on
software render tracking on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-5-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We're missing a workaround in the fbc code for all glk+ platforms
which can cause corruption around the top of the screen. So
enabling fbc by default is a bad idea. I'm not keen to backport
the w/a so let's start by disabling fbc by default on all glk+.
We'll lift the restriction once the w/a is in place.
Cc: stable@vger.kernel.org
Cc: Daniel Drake <drake@endlessm.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127201222.16669-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Commit 9c722e17c1 ("drm/i915: Disable pipes in reverse order")
reverted the order that pipes gets disabled because of TGL
master/slave relationship between transcoders in MST mode.
But as stated in a comment in skl_commit_modeset_enables() the
enabling order is not always crescent, possibly causing previously
selected slave transcoder being enabled before master so another
approach will be needed to select a transcoder to master in MST mode.
It will be similar to the approach taken in port sync.
But instead of implement something like
intel_trans_port_sync_modeset_disables() to MST lets simply it and
iterate over all pipes 2 times, the first one disabling any slave and
then disabling everything else.
The MST bits will be added in another patch.
v2:
Not using crtc->active as it is deprecated
v3:
Removing is_trans_port_sync_mode() check, just check for
is_trans_port_sync_master() is enough
v4:
Adding and using is_trans_port_sync_slave(), otherwise non-port sync
pipes will be disabled in the first loop, what is not wrong but is
not what patch description promises
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205210350.96795-3-jose.souza@intel.com
For TGL the step to turn off the transcoder clock was moved to after
the complete shutdown of DDI. Only the MST slave transcoders should
disable the clock before that.
v2:
- Adding last_mst_stream to intel_mst_post_disable_dp, make code more
easy to read and is similar to first_mst_stream in
intel_mst_pre_enable_dp()(Ville's idea)
- Calling intel_ddi_disable_pipe_clock() for GEN12+ right
intel_disable_ddi_buf() as stated in BSpec(Ville)
BSpec: 49190
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205210350.96795-2-jose.souza@intel.com
It should not care about DDB allocations of pipes going through
a fullmodeset, as at this point those pipes are disabled.
The comment in the code also points to that but that was not what
was being executed.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205210350.96795-1-jose.souza@intel.com
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting
-----BEGIN PGP SIGNATURE-----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=3cs2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
Assuming intel_crtc_arm_fifo_underrun() only gets called when
there's no pending plane updates we can utilize it on gen2 by
checking the active_planes bitmask so that we only re-enable
underrun reporting if some planes are active.
i915_fifo_underrun_reset_write() seems to have the necessary
hw_done/flip_done waits in place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127190556.1574-8-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Let's just inline intel_pre_disable_primary_noatomic() into
intel_plane_disable_noatomic(). The CxSR disable we can do
regardless of which plane we're disabling, and while at it we can
make the gen2 underrun w/a accurate by consulting the active_planes
bitmask.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127190556.1574-7-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We have the active_planes bitmask now so use it to properly
determine when some planes are visible for the gen2 underrun
workaround.
This let's us almost eliminate intel_post_enable_primary().
The manual underrun checks we can simply move into
intel_atomic_commit_tail() since they loop over all the pipes
already. No point in repeating the checks multiple times when
there are multiple pipes in the commit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127190556.1574-6-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Change the calling convention to just pass the state+crtc and
switch to intel_ types throughout.
We'll also do a quick s/if (old_primary_state)/if (new_primary_state)/
so that we'll be able to eliminate old_primary_state later. This
is fine since we always have either both old and new state or neither.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127190556.1574-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Disabling pipe/transcoder clock before power down sink could cause
sink lost signal, causing it to trigger a hotplug to notify source
that link signal was lost.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-2-jose.souza@intel.com
If the CRTC is going from enabled to disabled and it is a port sync
slave, it needs to check to the old state to be disabled before the
port sync master.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-1-jose.souza@intel.com
When looking at SDEISR to determine the connection status of combo
outputs, we should use the phy index rather than the port index.
Although they're usually the same thing, EHL's DDI-D (port D) is
attached to PHY-A and SDEISR doesn't even have bits for a "D" output.
It's also possible that future platforms may map DDIs (the internal
display engine programming units) to PHYs (the output handling on the IO
side) in ways where port!=phy, so let's look at the PHY index by
default.
v2: Rename to intel_combo_phy_connected. (Lucas)
Fixes: 719d240026 ("drm/i915/ehl: Enable DDI-D")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-2-matthew.d.roper@intel.com
(cherry picked from commit 3d1e388d40)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The unaligned ioread32() will make us read byte by byte looking for the
vbt. We could just as well have done a ioread8() + a shift and avoid the
extra confusion on how we are looking for "$VBT".
However when using ACPI it's guaranteed the VBT is 4-byte aligned
per spec, so we can probably assume it here as well.
v2: do not try to simplify the loop by eliminating the auxiliary counter
(Jani and Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-4-lucas.demarchi@intel.com
We don't need to keep the pci rom mapped during the entire
intel_bios_init() anymore. Move it to the previous copy_vbt() function
and rename it to oprom_get_vbt() since now it's responsible to to all
operations related to get the vbt from the oprom.
v2: fix double __iomem attribute detected by sparse
v3: fix missing unmap on success (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-3-lucas.demarchi@intel.com
When we map the VBT through pci_map_rom() we may not be allowed
to simply discard the address space and go on reading the memory.
That doesn't work on my test system, but by dumping the rom via
sysfs I can can get the correct vbt. So change our find_vbt() to do
the same as done by pci_read_rom(), i.e. use memcpy_fromio().
v2: the just the minimal changes by not bothering with the unaligned io
reads: this can be done on top (from Ville and Jani)
v3: drop const in function return since now we are copying the vbt,
rather than just finding it
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191126225110.8127-2-lucas.demarchi@intel.com
From VBT 228+ this is block that PSR and other power saving
features configuration should be read from.
v3:
Using DRRS from this new block
v4:
Using BIT()
Fixing DRRS comment in parse_power_conservation_features()
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-5-jose.souza@intel.com
eDP specification states that sink can have its PSR capability
changed, I have never found any panel doing that but lets add that
for completeness.
For now it is not reading back the PSR capabilities and if possible
re-enabling PSR, this will be added if a panel is found using this
feature.
v4:
Cleaning DP_PSR_CAPS_CHANGE
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-4-jose.souza@intel.com
When this error happens sink link is not stable after the required
FW_EXIT_LATENCY period so it will miss the selective update.
As the other PSR errors, for now we are not trying to recover from
it.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-3-jose.souza@intel.com
eDP spec states that when sink enconters a problem that prevents it
to keep PSR running it should set PSR status to internal error and
set the reason why it happen to PSR_ERROR_STATUS but it is not how it
was implemented.
But also I don't want to change this behavior, who knows if there is
a panel out there that only set the PSR_ERROR_STATUS.
So here refactoring the code a bit to make more easy to read what was
state above as more checks will be added to this function.
v2:
returning a int instead of a bool in psr_get_status_and_error_status()
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-2-jose.souza@intel.com
PSR2 HW only support a limited number of bits per pixel, if mode has
more than supported PSR2 should not be enabled.
BSpec: 50422
BSpec: 7713
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128014852.214135-1-jose.souza@intel.com
The "err" label is not really "err", but rather "out" since the return
path is shared between error condition and normal path. This broke when
commit 03cea61076 ("drm/i915/dsb: fix extra warning on error path
handling") added a "dsb->cmd_buf = NULL;" there, making DSB to stop
working since now all writes would pass-through via mmio.
Remove the set to NULL since it's actually not needed: we only set it if
all steps are successful. While at it, rename the label so this confusion
doesn't happen again.
Fixes: 03cea61076 ("drm/i915/dsb: fix extra warning on error path handling")
Resolves: https://gitlab.freedesktop.org/drm/intel/issues/8
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221119.384754-1-lucas.demarchi@intel.com
When looking at SDEISR to determine the connection status of combo
outputs, we should use the phy index rather than the port index.
Although they're usually the same thing, EHL's DDI-D (port D) is
attached to PHY-A and SDEISR doesn't even have bits for a "D" output.
It's also possible that future platforms may map DDIs (the internal
display engine programming units) to PHYs (the output handling on the IO
side) in ways where port!=phy, so let's look at the PHY index by
default.
v2: Rename to intel_combo_phy_connected. (Lucas)
Fixes: 719d240026 ("drm/i915/ehl: Enable DDI-D")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-2-matthew.d.roper@intel.com
The South Display is part of the PCH so we should technically be basing
our port detection logic off the PCH in use rather than the platform
generation.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-1-matthew.d.roper@intel.com
LPT/WPT only have PCH transcoder A. Make sure we poke at its
chicken register instead of some non-existent register when
FDI is being driven by pipe B or C.
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191128182358.14477-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
-----BEGIN PGP SIGNATURE-----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=Hj7G
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Starting with gen12, PORT_A can be connected to a transcoder
with audio support. Modify the existing logic that disabled
audio on PORT_A unconditionally.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191125125313.17584-1-kai.vehmanen@linux.intel.com
According to BSpec 53998, there is a mask of
max 8 SAGV/QGV points we need to support.
Bumping this up to keep the CI happy(currently
preventing tests to run), until all SAGV
changes land.
v2: Fix second plane where QGV points were
hardcoded as well.
v3: Change the naming of I915_NUM_SAGV_POINTS
to be I915_NUM_QGV_POINTS, as more meaningful
(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112189
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191125160800.14740-1-stanislav.lisovskiy@intel.com
[vsyrjala: Add missing braces around else (checkpatch), fix Bugzilla tag]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The bspec initially provided a single DKL PHY vswing table for both HDMI
and DP, but was recently updated to include an independent table for
HDMI.
Bspec: 49292
Fixes: 978c3e539b ("drm/i915/tgl: Add dkl phy programming sequences")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118180219.9309-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 362bfb995b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The bspec was recently updated with new cdclk -> voltage level tables to
accommodate the new 324/326.4 cdclk values.
Bspec: 21809
Fixes: 63c9dae71d ("drm/i915/ehl: Add voltage level requirement table")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118164412.26216-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit d147483884)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
fbdev uses the physical address of our framebuffer for its fb_mmap()
routine. While we need to adapt this address for the new io BAR, we have
to fix v5.4 first! The simplest fix is to restore the smem back to v5.3
and we will then probably have to implement our fbops->fb_mmap() callback
to handle local memory.
Reported-by: Neil MacLeod <freedesktop@nmacleod.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112256
Fixes: 5f889b9a61 ("drm/i915: Disregard drm_mode_config.fb_base")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Neil MacLeod <freedesktop@nmacleod.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113180633.3947-1-chris@chris-wilson.co.uk
(cherry picked from commit abc5520704)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 9faf5fa4d3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Move the assert_vblank_disabled() into intel_crtc_vblank_on()
so that we don't have to inline it all over.
This does mean we now assert_vblank_disabled() during readout as well
but that is totally fine as it happens after drm_crtc_vblank_reset().
One can even argue it's what we want to do anyway to make sure
the reset actually happened.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118164430.27265-4-ville.syrjala@linux.intel.com
Just pass the atomic state and the crtc to intel_encoders_enable() & co.
Make life simpler when you don't have to think which state (old vs. new)
you have to pass in. Also constify the states while at it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118164430.27265-2-ville.syrjala@linux.intel.com
The bspec initially provided a single DKL PHY vswing table for both HDMI
and DP, but was recently updated to include an independent table for
HDMI.
Bspec: 49292
Fixes: 978c3e539b ("drm/i915/tgl: Add dkl phy programming sequences")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118180219.9309-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The bspec was recently updated with new cdclk -> voltage level tables to
accommodate the new 324/326.4 cdclk values.
Bspec: 21809
Fixes: 63c9dae71d ("drm/i915/ehl: Add voltage level requirement table")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118164412.26216-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
When we call intel_dsb_get(), the dsb initialization may fail for
various reasons. We already log the error message in that path, making
it unnecessary to trigger a warning that refcount == 0 when calling
intel_dsb_put().
So here we simplify the logic and do lazy shutdown: leaving the extra
refcount alive so when we call intel_dsb_put() we end up calling
i915_vma_unpin_and_release().
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111205024.22853-3-lucas.demarchi@intel.com
The current dsb API is not really prepared to handle multithread access.
I was debugging an issue that ended up fixed by commit a096883dda
("drm/i915/dsb: Remove PIN_MAPPABLE from the DSB object VMA") and was
puzzled how these atomic operations were guaranteeing atomicity.
if (atomic_add_return(1, &dsb->refcount) != 1)
return dsb;
Thread A could still be initializing dsb struct (and even fail in the
middle) while thread B would take a reference and use it (even
derefencing a NULL cmd_buf).
I don't think the atomic operations here will help much if this were
to support multithreaded scenario in future, so just remove them to
avoid confusion.
v2: Use refcount++ != 0 instead of ++refcount != 1 (from Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111205024.22853-2-lucas.demarchi@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20191116011539.18230-1-lucas.demarchi@intel.com
The LUTs are single buffered so in order to program them without
tearing we'd have to do it during vblank (actually to be 100%
effective it has to happen between start of vblank and frame start).
We have no proper mechanism for that at the moment so we just
defer loading them after the vblank waits have happened. That
is not quite sufficient (especially when committing multiple pipes
whose vblanks don't line up) so the LUT load will often leak into
the following frame causing tearing.
However in case the hardware wasn't previously using the LUT we
can preload it before setting the enable bit (which is double
buffered so won't tear). Let's determine if we can do such
preloading and make it happen. Slight variation between the
hardware requires some platforms specifics in the checks.
Hans is seeing ugly colored flash on VLV/CHV macchines (GPD win
and Asus T100HA) when the gamma LUT gets loaded for the first
time as the BIOS has left some junk in the LUT memory.
v2: Deal with uapi vs. hw crtc state split
s/GCM/CGM/ typo fix
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 051a6d8d3c ("drm/i915: Move LUT programming to happen after vblank waits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030190815.7359-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
(cherry picked from commit 0ccc42a2fd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit f77021372e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Make sure we have a crtc before probing its primary plane's
max stride. Initially I thought we can't get this far without
crtcs, but looks like we can via the dumb_create ioctl.
Not sure if we shouldn't disable dumb buffer support entirely
when we have no crtcs, but that would require some amount of work
as the only thing currently being checked is dev->driver->dumb_create
which we'd have to convert to some device specific dynamic thing.
Cc: stable@vger.kernel.org
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: aa5ca8b742 ("drm/i915: Align dumb buffer stride to 4k to allow for gtt remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106172349.11987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit baea9ffe64)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit aeec766133)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
VBT revision 229 adds a new "Generic DTD" block 58 and deprecates the
old LFP panel mode data in block 42. Let's start parsing this block to
fill in the panel fixed mode on devices with a >=229 VBT.
v2:
* Update according to the recent updates:
- DTD size is now 16 bits instead of 24
- polarity is now just a single bit for hsync and vsync and is
properly documented
* Minor checkpatch fix
v3:
* Now that panel options are parsed separately from the previous patch,
move generic DTD parsing into a function parallel to
parse_lfp_panel_dtd. We'll still fall back to looking at the legacy
LVDS timing block if the generic DTD fails. (Jani)
* Don't forget to actually set lfp_lvds_vbt_mode! (Jani)
* Drop "bdb_" prefix from dtd entry structure. (Jani)
* Follow C99 standard for structure's flexible array member. (Jani)
v4:
* Add "positive" to polarity field names for clarity. (Jani)
* Move VBT version check and fallback to legacy DTD parsing logic to a
helper to keep top-level VBT parsing uncluttered. (Jani)
* Restructure reserved bit packing at end of generic_dtd_entry from
"u32 rsvd:24" to "u8 rsvd[3]" to prevent copy/paste mistakes in the
future. (Jani)
Bspec: 54751
Bspec: 20148
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191115165132.9472-3-matthew.d.roper@intel.com
Newer VBT versions will add an alternate way to read panel DTD
information, so let's split parsing of the general panel information
from the timing data in preparation.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jesse Barnes <jsbarnes@google.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191115165132.9472-2-matthew.d.roper@intel.com
It's supposed to be just a const pointer.
Fixes: 074c77e3ec ("drm/i915/tgl: Gen-12 display loses Yf tiling and legacy CCS support")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191115120440.17883-1-jani.nikula@intel.com
(cherry picked from commit 48ea97fabe)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
fbdev uses the physical address of our framebuffer for its fb_mmap()
routine. While we need to adapt this address for the new io BAR, we have
to fix v5.4 first! The simplest fix is to restore the smem back to v5.3
and we will then probably have to implement our fbops->fb_mmap() callback
to handle local memory.
Reported-by: Neil MacLeod <freedesktop@nmacleod.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112256
Fixes: 5f889b9a61 ("drm/i915: Disregard drm_mode_config.fb_base")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Neil MacLeod <freedesktop@nmacleod.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113180633.3947-1-chris@chris-wilson.co.uk
(cherry picked from commit abc5520704)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
It's supposed to be just a const pointer.
Fixes: 074c77e3ec ("drm/i915/tgl: Gen-12 display loses Yf tiling and legacy CCS support")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191115120440.17883-1-jani.nikula@intel.com
Currently we're blindly poking at the frame start delay bits
in PIPECONF when trying to sanitize the hardware state. Those
bits decided to move elsewhere on HSW, so on many platforms
we're not doing anything at all here. Also we're forgetting
about the PCH transcoder entirely.
Add all the bit definitions for the various homes these bits
have had throughout the years, and reset them all to zero.
However I'm not entirely sure this is a safe thing to do. If
not I guess we'd want full readout+statecheck for this stuff.
For now let's stick to the current logic and hope for the
best.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191024122138.25065-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Backmerge to get dfce90259d ("Backmerge i915 security patches from
commit 'ea0b163b13ff' into drm-next") and thus 100d46bd72 ("Merge
Intel Gen8/Gen9 graphics fixes from Jon Bloomfield.").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
HDMI_PICTURE_ASPECT_NONE is zero and the connector state is kzalloc()'d
so no need to initialize conn_state->picture_aspect_ratio with it.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-6-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
HDMI_PICTURE_ASPECT_NONE means "Automatic" so when the user has that
selected we should keep whatever aspect ratio the mode already has.
Also no point in checking for connector->is_hdmi in the SDVO code
since we only attach the property to HDMI connectors.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-5-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
fbdev uses the physical address of our framebuffer for its fb_mmap()
routine. While we need to adapt this address for the new io BAR, we have
to fix v5.4 first! The simplest fix is to restore the smem back to v5.3
and we will then probably have to implement our fbops->fb_mmap() callback
to handle local memory.
Reported-by: Neil MacLeod <freedesktop@nmacleod.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112256
Fixes: 5f889b9a61 ("drm/i915: Disregard drm_mode_config.fb_base")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Neil MacLeod <freedesktop@nmacleod.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113180633.3947-1-chris@chris-wilson.co.uk
Tiger Lake supports HDMI on port A. For other platforms we ignore what
the VBT says regarding HDMI to workaround broken VBTs, see
commit 2ba7d7e043 ("drm/i915/bios: ignore HDMI on port A"). Make this
apply gen12+ so they inherit the TGL behavior.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113021935.41547-1-lucas.demarchi@intel.com
This register was being enabled after enable TRANS_DDI_FUNC_CTL and
PIPECONF/TRANS_CONF while BSpec states that it should be set when
enabling TRANS_DDI_FUNC_CTL.
BSpec: 49190
BSpec: 22243
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107214559.77087-3-jose.souza@intel.com
Adding pipe D support to DSI transcoder.
Not adding it for EDP transcoder code paths as only TGL has 4 pipes
and it do not have a EDP transcoder.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107214559.77087-2-jose.souza@intel.com
When we call intel_bios_is_valid_vbt(), size may not actually be the
size of the VBT, but rather the size of the blob the VBT is contained
in. For example, when mapping the PCI oprom, size will be the entire
oprom size. We don't want to read beyond what is reported to be the
VBT. So make sure we vbt->vbt_size makes sense and use that for
the latter checks.
v2: check for vbt_size after checking for vbt signature and give it a
more meaningful error message (from Jani)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191108003602.33526-3-lucas.demarchi@intel.com
The setting of MSA is done by the DDI .pre_enable() hook. And when we are
using MST, the MSA is only set to first mst stream by calling of
DDI .pre_eanble() hook. It raies issues to non-first mst streams.
Wrong MSA or missed MSA packets might show scrambled screen or wrong
screen.
This splits a setting of MSA to MST and SST cases. And In the MST case it
will call a setting of MSA after an allocating of Virtual Channel from
MST encoder pre_enable callback.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112212
Fixes: 0c06fa1560 ("drm/i915/dp: Add support of BT.2020 Colorimetry to DP MSA")
Fixes: d4a415dcda ("drm/i915: Fix MST oops due to MSA changes")
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106212636.502471-1-gwan-gyeong.mun@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
[vsyrjala: nuke spurious newline]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit bd8c9cca88)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113125241.20547-1-ville.syrjala@linux.intel.com
The warning should be just a warning. Where it is currently is wrong
since we already registered the connector on drm, meaning it dies later
on a NULL pointer deref if the VBT-overriding we have is removed. Move
the warning up.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191108214251.79305-1-lucas.demarchi@intel.com
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
(cherry picked from commit 59ed05ccdd)
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Using the array is getting clumsy. Make things a bit more dynamic.
Remove early returns on not having child devices when the end result
after "iterating" the empty list would be the same.
v3:
- use list_add_tail to not reverse the child device list (Ville)
v2:
- stick to previous naming of child devices (Ville)
- use kzalloc, handle failure
- initialize list head earlier to keep intel_bios_driver_remove() safe
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3e72da0b412354ed8be6719df55b0e0cc4caa61a.1573227240.git.jani.nikula@intel.com
The setting of MSA is done by the DDI .pre_enable() hook. And when we are
using MST, the MSA is only set to first mst stream by calling of
DDI .pre_eanble() hook. It raies issues to non-first mst streams.
Wrong MSA or missed MSA packets might show scrambled screen or wrong
screen.
This splits a setting of MSA to MST and SST cases. And In the MST case it
will call a setting of MSA after an allocating of Virtual Channel from
MST encoder pre_enable callback.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112212
Fixes: 0c06fa1560 ("drm/i915/dp: Add support of BT.2020 Colorimetry to DP MSA")
Fixes: d4a415dcda ("drm/i915: Fix MST oops due to MSA changes")
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106212636.502471-1-gwan-gyeong.mun@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
[vsyrjala: nuke spurious newline]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The LUTs are single buffered so in order to program them without
tearing we'd have to do it during vblank (actually to be 100%
effective it has to happen between start of vblank and frame start).
We have no proper mechanism for that at the moment so we just
defer loading them after the vblank waits have happened. That
is not quite sufficient (especially when committing multiple pipes
whose vblanks don't line up) so the LUT load will often leak into
the following frame causing tearing.
However in case the hardware wasn't previously using the LUT we
can preload it before setting the enable bit (which is double
buffered so won't tear). Let's determine if we can do such
preloading and make it happen. Slight variation between the
hardware requires some platforms specifics in the checks.
Hans is seeing ugly colored flash on VLV/CHV macchines (GPD win
and Asus T100HA) when the gamma LUT gets loaded for the first
time as the BIOS has left some junk in the LUT memory.
v2: Deal with uapi vs. hw crtc state split
s/GCM/CGM/ typo fix
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 051a6d8d3c ("drm/i915: Move LUT programming to happen after vblank waits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030190815.7359-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
(cherry picked from commit 0ccc42a2fd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Make sure we have a crtc before probing its primary plane's
max stride. Initially I thought we can't get this far without
crtcs, but looks like we can via the dumb_create ioctl.
Not sure if we shouldn't disable dumb buffer support entirely
when we have no crtcs, but that would require some amount of work
as the only thing currently being checked is dev->driver->dumb_create
which we'd have to convert to some device specific dynamic thing.
Cc: stable@vger.kernel.org
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: aa5ca8b742 ("drm/i915: Align dumb buffer stride to 4k to allow for gtt remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106172349.11987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit baea9ffe64)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The intel_dp_link_training.h include has no need or place in
intel_display.h. Include it in intel_display.c instead.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Fixes: eadf6f9170 ("drm/i915/display/icl: Enable master-slaves in trans port sync")
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029103947.7535-1-jani.nikula@intel.com
(cherry picked from commit 3c954c418e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Make sure we have a crtc before probing its primary plane's
max stride. Initially I thought we can't get this far without
crtcs, but looks like we can via the dumb_create ioctl.
Not sure if we shouldn't disable dumb buffer support entirely
when we have no crtcs, but that would require some amount of work
as the only thing currently being checked is dev->driver->dumb_create
which we'd have to convert to some device specific dynamic thing.
Cc: stable@vger.kernel.org
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: aa5ca8b742 ("drm/i915: Align dumb buffer stride to 4k to allow for gtt remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106172349.11987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than just specifying the bullet numbers from the bspec (e.g.,
"4.b") actually include the description of what the bspec wants us to
do. Steps can be renumbered or moved so including the description will
help us match the code up to the spec. Plus if we add support for new
platforms, some of the steps may be added/removed so more descriptive
comments will be useful for ensuring all of the bspec requirements are
met.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107174527.11165-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The LUTs are single buffered so in order to program them without
tearing we'd have to do it during vblank (actually to be 100%
effective it has to happen between start of vblank and frame start).
We have no proper mechanism for that at the moment so we just
defer loading them after the vblank waits have happened. That
is not quite sufficient (especially when committing multiple pipes
whose vblanks don't line up) so the LUT load will often leak into
the following frame causing tearing.
However in case the hardware wasn't previously using the LUT we
can preload it before setting the enable bit (which is double
buffered so won't tear). Let's determine if we can do such
preloading and make it happen. Slight variation between the
hardware requires some platforms specifics in the checks.
Hans is seeing ugly colored flash on VLV/CHV macchines (GPD win
and Asus T100HA) when the gamma LUT gets loaded for the first
time as the BIOS has left some junk in the LUT memory.
v2: Deal with uapi vs. hw crtc state split
s/GCM/CGM/ typo fix
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 051a6d8d3c ("drm/i915: Move LUT programming to happen after vblank waits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030190815.7359-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The intel_dp_link_training.h include has no need or place in
intel_display.h. Include it in intel_display.c instead.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Fixes: eadf6f9170 ("drm/i915/display/icl: Enable master-slaves in trans port sync")
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029103947.7535-1-jani.nikula@intel.com
Prefer using intel_encoder and pass the base where needed rather than
keeping both encoder and intel_encoder variables around.
v2: actually add all changes to the patch
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106071715.10613-1-lucas.demarchi@intel.com
The uapi vs. hw state split introduced a bug in
intel_crtc_disable_noatomic() where it's now frobbing an already
freed temp crtc state instead of adjusting the crtc state we
are really left with. Fix that by making a cleaner separation
beteen the two.
This causes explosions on any machine that boots up with pipes
already running but not hooked up to any encoder (typical
behaviour for gen2-4 VBIOS).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 58d124ea27 ("drm/i915: Complete crtc hw/uapi split, v6.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191105171447.22111-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Split out the DP specific parts, making it easier to add DSI specific
configuration. Also move the encoder specific parts towards the end, to
allow overriding generic configuration if needed. This also improves
clarity by making it clear the encoder independent configuration does
not depend on the encoder specific parts.
v2: Rebase
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104141439.26312-3-jani.nikula@intel.com
Use a simple pointer to the relevant element instead of duplicating the
array subscription. No functional changes.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104141439.26312-2-jani.nikula@intel.com
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
For MST on Tiger Lake there are different moments when we need to
configure the transcoder clock select. For the first link this is in step
7.a of the spec, before training the link. For additional streams this
should be done as part of step 8.b after programming receiver VC Payload
ID.
Bspec: 49190
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-4-lucas.demarchi@intel.com
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes: e9b7e1422d ("drm/i915: Sanitize the terminology used for TypeC port modes")
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029011014.286885-1-jose.souza@intel.com
(cherry picked from commit 4974826482)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
For the HPD interrupt functionality the HW depends on power wells in the
display core domain to be on. Accordingly when enabling these power
wells the HPD polling logic will force an HPD detection cycle to account
for hotplug events that may have happened when such a power well was
off.
Thus a detect cycle started by polling could start a new detect cycle if
a power well in the display core domain gets enabled during detect and
stays enabled after detect completes. That in turn can lead to a
detection cycle runaway.
To prevent re-triggering a poll-detect cycle make sure we drop all power
references we acquired during detect synchronously by the end of detect.
This will let the poll-detect logic continue with polling (matching the
off state of the corresponding power wells) instead of scheduling a new
detection cycle.
Fixes: 6cfe7ec02e ("drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112125
Reported-and-tested-by: Val Kulkov <val.kulkov@gmail.com>
Reported-and-tested-by: wangqr <wqr.prg@gmail.com>
Cc: Val Kulkov <val.kulkov@gmail.com>
Cc: wangqr <wqr.prg@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028181517.22602-1-imre.deak@intel.com
(cherry picked from commit a8ddac7c9f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Lots of redundant assignments inside intel_primary_plane_create().
Get rid of them.
v2: Rebase due to fp16 landing
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-8-ville.syrjala@linux.intel.com
Let's try to keep the pixel format arrays somewhat sorted:
1. RGB before YUV
2. smaller bpp before larger bpp
3. X before A
4. RGB before BGR
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-7-ville.syrjala@linux.intel.com
ICL+ again supports alpha blending with 10bpc pixel formats.
Expose them.
v2: Add all the stuff I missed earlier!
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-6-ville.syrjala@linux.intel.com
CHV pipe B sprites gained support for the 10bpc X/ARGB pixel formats.
On VLV and CHV pipe A/C these are only supported by the primary
plane. Add the require bits to expose the new formats.
v2: Reorder the formats for consistency
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-4-ville.syrjala@linux.intel.com
UAPI Changes:
- Make context persistence optional
Allow userspace to tie the context lifetime to FD lifetime,
effectively allowing Ctrl-C killing of a process to also clean
up the hardware immediately.
Compute changes: https://github.com/intel/compute-runtime/pull/228
The compute driver is shipping in Ubuntu. uAPI acked by Mesa folks.
- Put future HW and their uAPIs under STAGING & BROKEN
Introduces DRM_I915_UNSTABLE Kconfig menu for working on the new
uAPI for future HW in upstream. We already disable driver loading
by default the platform is deemed ready. This is a second level
of protection based on compile time switch (STAGING & BROKEN).
- Under DRM_I915_UNSTABLE: Add the fake lmem region on iGFX
Fake local memory region on integrated GPU through cmdline:
memmap=2G$16G i915.fake_lmem_start=0x400000000
Currently allows testing non-mappable GGTT behavior and running
kernel selftest for local memory.
Driver Changes:
- Fix Bugzilla #112084: VGA external monitor not working (Ville)
- Add support for half float framebuffers (Ville)
- Add perf support on TGL (Lionel)
- Replace hangcheck by heartbeats (Chris)
- Allow SPT PCH on all AML devices (James)
- Add new CNL PCH for CML platform (Imre)
- Allow 100 ms (Kconfig) for workloads to exit before reset (Chris, Jon, Joonas)
- Forcibly pre-empt a context after 100 ms (Kconfig) of delay (Chris)
- Make timeslice duration Kconfig configurable (Chris)
- Whitelist PS_(DEPTH|INVOCATION)_COUNT for Tigerlake (Tapani)
- Support creating LMEM objects in kernel (Matt A)
- Adjust the location of RING_MI_MODE in the context image for TGL (Chris)
- Handle AUX interrupts for TC ports (Matt R)
- Add support for devices without mappable GGTT aperture (Daniele)
- Rename "inject_load_failure" module parameter to "inject_probe_failure" (Janusz)
- Handle fused off HDCP, FBC, DMC and DSC (Jose)
- Add support to one DP-MST stream on Tigerlake (Lucas)
- Add HuC firmware (and GuC) for TGL (Daniele)
- Allow ICL+ DSI on any pipe (Ville)
- Check some transcoder timing minimum limits (Ville)
- Don't set queue_priority_hint if we don't kick the submission (Chris)
- Introduce barrier pulses along engines to flush idle/in-flight requests (Chris)
- Drop assertion that ce->pin_mutex guards state updates (Chris)
- Cancel banned contexts on schedule-out (Chris)
- Cancel contexts when hangchecking is disabled (Chris)
- Catch GTT fault errors for gen11+ planes (Matt R)
- Print in debugfs if PSR is not enabled because of sink (Jose)
- Do not set MOCS control values on dgfx (Lucas)
- Setup io-mapping for LMEM (Abdiel)
- Support kernel mapping of LMEM objects (Abdiel)
- Add LMEM selftests (Matt A)
- Initialise PMU spinlock before registering (Chris)
- Clear DKL_TX_PMD_LANE_SUS before program TC voltage swing (Jose)
- Flip interpretation of ips fmin/fmax to max rps (Chris)
- Add VBT compression parameter block definition (Jani)
- Limit the blitter sizes to ensure low preemption latency (Chris)
- Fixup block_size rounding on BLT (Matt A)
- Don't try to place HWS in non-existing mappable region (Michal Wa)
- Don't allocate the ring in stolen if we lack aperture (Matt A)
- Add AUX B & C to DC_OFF_POWER_DOMAINS for Tigerlake (Matt R)
- Avoid HPD poll detect triggering a new detect cycle (Imre)
- Document the userspace fail with possible_crtcs (Ville)
- Drop lrc header page now unused by GuC (Daniele)
- Do not switch aux to TBT mode for non-TC ports (Jose)
- Restructure code to avoid depending on i915 but smaller structs (Chris, Tvrtko, Andi)
- Remove pm park/unpark notifications (Chris)
- Avoid lockdep cross-contamination between object types (Chris)
- Restructure DSC code (Jani)
- Fix dead locking in early workload shadow (Zhenyu)
- Split the legacy submission backend from the common CS ring buffer (Chris)
- Move intel_engine_context_in/out into intel_lrc.c (Tvrtko)
- Describe perf/wakeref structure members in documentation (Anna)
- Update renamed header files names in documentation (Anna)
- Add debugs to distingiush a cd2x update from a full cdclk pll update (Ville)
- Rework atomic global state locking (Ville)
- Allow planes to declare their minimum acceptable cdclk (Ville)
- Eliminate skl_check_pipe_max_pixel_rate() and simplify skl_max_scale() (Ville)
- Making loglevel of PSR2/SU logs same (Ap)
- Capture aux page table error register (Lionel)
- Add is_dgfx to device info (Jose)
- Split gen11_irq_handler to make it shareable (Lucas)
- Encapsulate kconfig constant values inside boolean predicates (Chris)
- Split memory_region initialisation into its own file (Chris)
- Use _PICK() for CHICKEN_TRANS() and add CHICKEN_TRANS_D (Ville)
- Add perf helper macros for comparing with whitelisted registers (Umesh)
- Fix i915_inject_load_error() name to read *_probe_* (Janusz)
- Drop unused AUX register offsets (Matt R)
- Provide more information on DP AUX failures (Matt R)
- Add GAM/SFC instdone to error state (Mika)
- Always track callers to intel_rps_mark_interactive() (Chris)
- Nuke 'mode' argument to intel_get_load_detect_pipe() (Ville)
- Simplify LVDS crtc_mask and pipe_mask setup (Ville)
- Stop frobbing crtc->base.mode (Ville)
- Do s/crtc_mask/pipe_mask/ (Ville)
- Split detaching and removing the vma (Chris)
- Selftest improvements (Chris, Tvrtko, Mika, Matt A, Lionel)
- GuC code improvements (Rob, Andi, Daniele)
- Check against i915_selftest only under CONFIG_SELFTEST (Chris)
- Refine occupancy test in kill_context() (Chris)
- Start kthreads before stopping (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101104718.GA14323@jlahtine-desk.ger.corp.intel.com
Now that we split plane_state which I didn't want to do yet, we can
program the slave plane without requiring the master plane.
This is useful for programming bigjoiner slave planes as well. We
will no longer need the master's plane_state.
Changes since v1:
- set src/dst rectangles after copy_uapi_to_hw_state.
Changes since v2:
- Use the correct color_plane for pre-gen11 by using planar_linked_plane != NULL.
- Use drm_format_info_is_yuv_semiplanar in skl_plane_check() to fix gen11+.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-12-maarten.lankhorst@linux.intel.com
Splitting plane state is easier than splitting crtc_state,
before plane check we copy the drm properties to hw so we can
do the same in bigjoiner later on.
We copy the state after we did all the modeset handling, but fortunately
i915 seems to be split correctly and nothing during modeset looks
at plane_state.
Changes since v1:
- Do not clear hw state on duplication.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-11-maarten.lankhorst@linux.intel.com
Split up plane_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_plane_state *T;
identifier x;
@@
-T->base.x
+T->uapi.x
@@
struct intel_plane_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-10-maarten.lankhorst@linux.intel.com
Split up plane_state->base to hw. This is done using the following patch:
@@
struct intel_plane_state *T;
identifier x =~ "^(crtc|fb|alpha|pixel_blend_mode|rotation|color_encoding|color_range)$";
@@
-T->base.x
+T->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-9-maarten.lankhorst@linux.intel.com
get_crtc_from_states() is called before plane_state is copied to uapi,
so use the uapi state there.
intel_legacy_cursor_update() could probably get away with looking at
the hw state, but for clarity always look at the uapi state.
Changes since v1:
- Convert entirety of intel_legacy_cursor_update (Ville).
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-8-maarten.lankhorst@linux.intel.com
Prepare to split up hw and uapi machinally, by adding a uapi and
hw alias. We will remove the base in a bit. This is a split from the
original uapi/hw patch, which did it all in one go.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Now that we separated everything into uapi and hw, it's
time to make the split definitive. Remove the union and
make a copy of the hw state on modeset and fastset.
Color blobs are copied in crtc atomic_check(), right
before color management is checked.
Changes since v1:
- Copy all blobs immediately after drm_atomic_helper_check_modeset().
- Clear crtc_state->hw on disable, instead of using clear_intel_crtc_state().
Changes since v2:
- Use intel_crtc_free_hw_state + clear in intel_crtc_disable_noatomic().
- Make a intel_crtc_prepare_state() function that clears the crtc_state
and copies hw members.
- Remove setting uapi.adjusted_mode, we now have a direct call to
drm_calc_timestamping_constants().
Changes since v3:
- Rename prefix copy_hw_to_uapi_state() with intel_crtc.
- Copy color blobs to uapi as well.
- Add a intel_crtc_copy_uapi_to_hw_state_nomodeset() function for clarity.
Changes since v4:
- Copy hw.adjusted_mode back to uapi.adjusted_mode, to shut up
the call to drm_calc_timestamping_constants() in
drm_atomic_helper_update_legacy_modeset_state().
- Use drm_property_replace_blob (Ville).
Changes since v5:
- Use hw->mode in intel_modeset_readout_hw_state(). (Ville)
- Copy to uapi.mode using drm_atomic_set_mode_for_crtc(). (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
Split up crtc_state->base to hw where appropriate. This is done using the following patch:
@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x
@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com
intel_get_load_detect_pipe() needs to set uapi active,
uapi enable is set by the call to drm_atomic_set_mode_for_crtc(),
so we can remove it.
intel_pipe_config_compare() needs to look at hw state, but I didn't
change spatch to look at it. It's easy enough to do manually.
intel_atomic_check() definitely needs to check for uapi enable,
otherwise intel_modeset_pipe_config cannot copy uapi state to hw.
Changes since v1:
- Actually set uapi.active in get_load_detect_pipe().
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-3-maarten.lankhorst@linux.intel.com
Prepare to split up hw and uapi machinally, by adding a uapi and
hw alias. We will remove the base in a bit. This is a split from the
original uapi/hw patch, which did it all in one go.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We are still looking at drm_crtc_state in a few places, convert those
to use intel_crtc_state instead.
Changes since v1:
- Move to before uapi/hw split.
- Add hunks for intel_pm.c as well.
Changes since v2:
- Incorporate Ville's feedback.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-1-maarten.lankhorst@linux.intel.com
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes: e9b7e1422d ("drm/i915: Sanitize the terminology used for TypeC port modes")
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029011014.286885-1-jose.souza@intel.com
To avoid accidentally breaking things in the future add a
comment explaining why we misconfigure the pipe_mask.
Also toss in a TODO for investigating a single encoder
approach as opposed to the encoder-per-pipe approach.
v2: Drop a bogus TODO comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-6-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
There are no longer any pipe<->DSI port limitations on icl+.
Populate the pipe_mask accordingly.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-4-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
We don't need to special case PCH vs. gen4 when setting up the LVDS
crtc_mask. Just claim pipes A|B|C work and
intel_encoder_possible_crtcs() will drop out any crtc that doesn't
exist.
v2: Put the special case first to match what most other encoders do
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-2-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
The core no longer uses drm_crtc_state::mode with atomic drivers,
so let's stop frobbing it in the driver. For the user mode readout
we'll just use an on stack mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029145526.10308-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
For the HPD interrupt functionality the HW depends on power wells in the
display core domain to be on. Accordingly when enabling these power
wells the HPD polling logic will force an HPD detection cycle to account
for hotplug events that may have happened when such a power well was
off.
Thus a detect cycle started by polling could start a new detect cycle if
a power well in the display core domain gets enabled during detect and
stays enabled after detect completes. That in turn can lead to a
detection cycle runaway.
To prevent re-triggering a poll-detect cycle make sure we drop all power
references we acquired during detect synchronously by the end of detect.
This will let the poll-detect logic continue with polling (matching the
off state of the corresponding power wells) instead of scheduling a new
detection cycle.
Fixes: 6cfe7ec02e ("drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112125
Reported-and-tested-by: Val Kulkov <val.kulkov@gmail.com>
Reported-and-tested-by: wangqr <wqr.prg@gmail.com>
Cc: Val Kulkov <val.kulkov@gmail.com>
Cc: wangqr <wqr.prg@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028181517.22602-1-imre.deak@intel.com
This is the minimum change to support 1 (and only 1) DP-MST monitor
connected on Tiger Lake. This change was isolated from previous patch
from José. In order to support more streams we will need to create a
master-slave relation on the transcoders and that is not currently
working yet.
v2: remove unused macro and use REG_FIELD_PREP() (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029035049.5907-1-lucas.demarchi@intel.com
Replace PLLs names used in documentation to that used in the code.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Fixes: 68ff39c3f8 ("drm/i915/tgl: Add new pll ids")
Signed-off-by: Anna Karas <anna.karas@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926123559.15717-1-anna.karas@intel.com
(cherry picked from commit d328bd4f90)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We're seeing some failures where an aux transaction still shows as
'busy' well after the timeout limit that the hardware is supposed to
enforce. Improve the error message so that we can see exactly which aux
channel this error happened on and what the status bits were during this
case that isn't supposed to happen.
v2:
- Make timeout a const variable so that the timeout & message will
match if we decide to change it in the future. (Lucas)
- Don't bother testing intel_dp->aux.name for NULL. (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029173102.9451-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
DSC could be fused off, so not all GEN10+ platforms will support it.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-5-jose.souza@intel.com
HDCP could be fused off, so not all GEN9+ platforms will support it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-2-jose.souza@intel.com
Our TGL CI platforms are running into cases where aux transactions have
failed to complete or declare a timeout well after the timeout limit
that the hardware is supposed to enforce. From the logs it appears that
these failures arise when aux transactions happen after we've entered
DC6:
<7> [622.523650] [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [622.523685] [drm:gen9_set_dc_state [i915]] Setting DC state from 00 to 02
...
<3> [622.535753] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.547745] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.559746] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.571744] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.583743] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.583780] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp_aux_ch not done status 0xad400bff
<7> [622.863725] [drm:drm_dp_dpcd_access] Too many retries, giving up. First error: -110
On TGL AUX B & C are in PG1 (managed by the DMC firmware) rather
than PG3 as they were on ICL, so allowing DC6 means the DMC firmware
might shut off the power wells behind our backs when we're trying to use
them.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025230623.27829-6-matthew.d.roper@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The change from the uapi coordinates to the internal coordinates
broke the cursor on i845/i865 due to src and dst getting swapped.
Fix it.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 3a612765f4 ("drm/i915: Remove cursor use of properties for coordinates")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
smatch complains about
drivers/gpu/drm/i915//display/intel_display.c:14403 intel_set_dp_tp_ctl_normal() error: uninitialized symbol 'conn'.
because it has no way to determine that the loop must have an entry.
Tell the static analysers to ignore the local, it will always be set.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028142652.1987-2-chris@chris-wilson.co.uk
i915_irq.c is large. One reason for this is that has a large chunk of
the GT render power management stashed away in it. Extract that logic
out of i915_irq.c and intel_pm.c and put it under one roof.
Based on a patch by Chris Wilson.
Signed-off-by: Andi Shyti <andi.shyti@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191024211642.7688-1-chris@chris-wilson.co.uk
This sequence was recently added to fix internal HW sequences to
reset TC ports.
HSDES: 1507287614
HSDES: 14010071447
BSpec: 49292
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191021223408.87344-1-jose.souza@intel.com
Replace PLLs names used in documentation to that used in the code.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Fixes: 68ff39c3f8 ("drm/i915/tgl: Add new pll ids")
Signed-off-by: Anna Karas <anna.karas@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926123559.15717-1-anna.karas@intel.com
Add description of wakeref member of intel_shared_dpll
structure to documentation.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Anna Karas <anna.karas@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008092849.6511-1-anna.karas@intel.com
'Link CRC error' will now have same error level as
other PSR2 errors like 'RFB storage error' and
'VSC SDP uncorrectable error'.
Signed-off-by: Ap Kamal <kamal.ap@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1571819128-3264-1-git-send-email-kamal.ap@intel.com
Finally! For a very long time, our MST helpers have had one very
annoying issue: They don't know how to reprobe the topology state when
coming out of suspend. This means that if a user has a machine connected
to an MST topology and decides to suspend their machine, we lose all
topology changes that happened during that period. That can be a big
problem if the machine was connected to a different topology on the same
port before resuming, as we won't bother reprobing any of the ports and
likely cause the user's monitors not to come back up as expected.
So, we start fixing this by teaching our MST helpers how to reprobe the
link addresses of each connected topology when resuming. As it turns
out, the behavior that we want here is identical to the behavior we want
when initially probing a newly connected MST topology, with a couple of
important differences:
- We need to be more careful about handling the potential races between
events from the MST hub that could change the topology state as we're
performing the link address reprobe
- We need to be more careful about handling unlikely state changes on
ports - such as an input port turning into an output port, something
that would be far more likely to happen in situations like the MST hub
we're connected to being changed while we're suspend
Both of which have been solved by previous commits. That leaves one
requirement:
- We need to prune any MST ports in our in-memory topology state that
were present when suspending, but have not appeared in the post-resume
link address response from their parent branch device
Which we can now handle in this commit by modifying
drm_dp_send_link_address(). We then introduce suspend/resume reprobing
by introducing drm_dp_mst_topology_mgr_invalidate_mstb(), which we call
in drm_dp_mst_topology_mgr_suspend() to traverse the in-memory topology
state to indicate that each mstb needs it's link address resent and PBN
resources reprobed.
On resume, we start back up &mgr->work and have it reprobe the topology
in the same way we would on a hotplug, removing any leftover ports that
no longer appear in the topology state.
Changes since v4:
* Split indenting changes in drm_dp_mst_topology_mgr_resume() into a
separate patch
* Only fire hotplugs when something has actually changed after a link
address probe
* Don't try to change port->connector at all on ports, just throw out
ports that need their connectors removed to make things easier.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-14-lyude@redhat.com
This is a complicated one. Essentially, there's currently a problem in the MST
core that hasn't really caused any issues that we're aware of (emphasis on "that
we're aware of"): locking.
When we go through and probe the link addresses and path resources in a
topology, we hold no locks when updating ports with said information. The
members I'm referring to in particular are:
- ldps
- ddps
- mcs
- pdt
- dpcd_rev
- num_sdp_streams
- num_sdp_stream_sinks
- available_pbn
- input
- connector
Now that we're handling UP requests asynchronously and will be using some of
the struct members mentioned above in atomic modesetting in the future for
features such as PBN validation, this is going to become a lot more important.
As well, the next few commits that prepare us for and introduce suspend/resume
reprobing will also need clear locking in order to prevent from additional
racing hilarities that we never could have hit in the past.
So, let's solve this issue by using &mgr->base.lock, the modesetting
lock which currently only protects &mgr->base.state. This works
perfectly because it allows us to avoid blocking connection_mutex
unnecessarily, and we can grab this in connector detection paths since
it's a ww mutex. We start by having drm_dp_mst_handle_up_req() hold this
when updating ports. For drm_dp_mst_handle_link_address_port() things
are a bit more complicated. As I've learned the hard way, we can grab
&mgr->lock.base for everything except for port->connector. See, our
normal driver probing paths end up generating this rather obvious
lockdep chain:
&drm->mode_config.mutex
-> crtc_ww_class_mutex/crtc_ww_class_acquire
-> &connector->mutex
However, sysfs grabs &drm->mode_config.mutex in order to protect itself
from connector state changing under it. Because this entails grabbing
kn->count, e.g. the lock that the kernel provides for protecting sysfs
contexts, we end up grabbing kn->count followed by
&drm->mode_config.mutex. This ends up creating an extremely rude chain:
&kn->count
-> &drm->mode_config.mutex
-> crtc_ww_class_mutex/crtc_ww_class_acquire
-> &connector->mutex
I mean, look at that thing! It's just evil!!! This gross thing ends up
making any calls to drm_connector_register()/drm_connector_unregister()
impossible when holding any kind of modesetting lock. This is annoying
because ideally, we always want to ensure that
drm_dp_mst_port->connector never changes when doing an atomic commit or
check that would affect the atomic topology state so that it can
reliably and easily be used from future DRM DP MST helpers to assist
with tasks such as scanning through the current VCPI allocations and
adding connectors which need to have their allocations updated in
response to a bandwidth change or the like.
Being able to hold &mgr->base.lock throughout the entire link probe
process would have been _great_, since we could prevent userspace from
ever seeing any states in-between individual port changes and as a
result likely end up with a much faster probe and more consistent
results from said probes. But without some rework of how we handle
connector probing in sysfs it's not at all currently possible. In the
future, maybe we can try using the sysfs locks to protect updates to
connector probing state and fix this mess.
So for now, to protect everything other than port->connector under
&mgr->base.lock and ensure that we still have the guarantee that atomic
check/commit contexts will never see port->connector change we use a
silly trick. See: port->connector only needs to change in order to
ensure that input ports (see the MST spec) never have a ghost connector
associated with them. But, there's nothing stopping us from simply
throwing the entire port out and creating a new one in order to maintain
that requirement while still keeping port->connector consistent across
the lifetime of the port in atomic check/commit contexts. For all
intended purposes this works fine, as we validate ports in any contexts
we care about before using them and as such will end up reporting the
connector as disconnected until it's port's destruction finalizes. So,
we just do that in cases where we detect port->input has transitioned
from true->false. We don't need to worry about the other direction,
since a port without a connector isn't visible to userspace and as such
doesn't need to be protected by &mgr->base.lock until we finish
registering a connector for it.
For updating members of drm_dp_mst_port other than port->connector, we
simply grab &mgr->base.lock in drm_dp_mst_link_probe_work() for already
registered ports, update said members and drop the lock before
potentially registering a connector and probing the link address of it's
children.
Finally, we modify drm_dp_mst_detect_port() to take a modesetting lock
acquisition context in order to acquire &mgr->base.lock under
&connection_mutex and convert all it's users over to using the
.detect_ctx probe hooks.
With that, we finally have well defined locking.
Changes since v4:
* Get rid of port->mutex, stop using connection_mutex and just use our own
modesetting lock - mgr->base.lock. Also, add a probe_lock that comes
before this patch.
* Just throw out ports that get changed from an output to an input, and
replace them with new ports. This lets us ensure that modesetting
contexts never see port->connector go from having a connector to being
NULL.
* Write an extremely detailed explanation of what problems this is
trying to fix, since there's a _lot_ of context here and I honestly
forgot some of it myself a couple times.
* Don't grab mgr->lock when reading port->mstb in
drm_dp_mst_handle_link_address_port(). It's not needed.
Cc: Juston Li <juston.li@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022023641.8026-7-lyude@redhat.com
snb supports fp16 pixel formats on the sprite planes. Expose that
capability. Nothing special needs to be done, it just works.
v2: Rebase on top of icl fp16
Split snb+ sprite bits into a separate patch
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-11-ville.syrjala@linux.intel.com
ivb+ supports fp16 pixel formats on the sprite planes planes. Expose
that capability.
On ivb/hsw fp16 scanout is slightly busted. The output from the plane
will have 1/4 the expected value. For the sprite plane we can fix that
up with the plane gamma unit. This was fixed on bdw.
v2: Rebase on top of icl fp16
Split the ivb+ sprite birs into a separate patch
v3: Move ivb_need_sprite_gamma() check one level up so that
we don't waste time programming garbage into he gamma registers
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-10-ville.syrjala@linux.intel.com
gen4+ supports fp16 pixel formats on the primary planes. Add the
relevant code.
On ivb fp16 scanout is slightly busted. The output from the plane will
have 1/4 the expected value. For the primary plane we would have to
use the pipe gamma or pipe csc to correct that which would affect all
the other planes as well, hence we simply choose not to expose fp16
on the ivb primary plane. On hsw the primary plane got fixed.
On gmch platforms I observed that the plane width must be below 2k
pixels with fp16 or else we get a corrupted image. This limitation
does not seem to be documented in bspec. I verified the exact limit
using the chv pipe B primary plane since it has windowing capability.
The stride limits are unaffected by fp16.
v2: Rebase on top of icl fp16
Split thea gen4+ primary plane bits into a separate patch
Deal with HAS_GMCH()
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-9-ville.syrjala@linux.intel.com
skl+ supports fp16 pixel formats on all universal planes. Add the
necessary bits to expose that capability. The main different to
icl is that we can't scale fp16, so need to add the relevant
checks.
v2: Rebase on top of icl fp16
Split skl+ bits into a separate patch
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-8-ville.syrjala@linux.intel.com
Now that the planes declare their minimum cdclk requirements properly
we don't need to check the cdclk in skl_max_scale() anymore. Just check
against the maximum downscale ratio, and move the code next to it's
only caller.
v2: Add a comment explaining the HQ vs. not thing
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-7-ville.syrjala@linux.intel.com
The normal cdclk handling now takes care of making sure the
plane's pixel rate doesn't exceed the spec appointed percentage
of the cdclk frequency. Thus we can nuke
skl_check_pipe_max_pixel_rate().
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-6-ville.syrjala@linux.intel.com
Various pixel formats and plane scaling impose additional constraints
on the cdclk frequency. Provide a new plane->min_cdclk() hook that
will be used to compute the minimum acceptable cdclk frequency for
each plane.
Annoyingly on some platforms the numer of active planes affects
this calculation so we must also toss in more planes into the
state when the number of active planes changes.
The sequence of state computation must also be changed:
1. check_plane() (updates plane's visibility etc.)
2. figure out if more planes now require update min_cdclk
computaion
3. calculate the new min cdclk for each plane in the state
4. if the minimum of any plane now exceeds the current
logical cdclk we recompute the cdclk
4. during cdclk computation take the planes' min_cdclk into
accoutn
5. follow the normal cdclk programming to change the
cdclk frequency. This may now require a modeset (except
on bxt/glk in some cases), which either succeeds or
fails depending on whether userspace has given
us permission to perform a modeset or not.
v2: Fix plane id check in intel_crtc_add_planes_to_state()
Only print the debug message when cdclk needs bumping
Use dev_priv->cdclk... as the old state explicitly
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-5-ville.syrjala@linux.intel.com
check_digital_port_conflicts() is done needlessly late. Move it earlier.
This will be needed as later on we want to set any_ms=true a bit later
for non-modesets too and we can't call this guy without the
connection_mutex held.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
So far we've sort of protected the global state under dev_priv with
the connection_mutex. I wan to change that so that we can change the
cdclk even for pure plane updates. To that end let's formalize the
protection of the global state to follow what I started with the cdclk
code already (though not entirely properly) such that any crtc mutex
will suffice as a read lock, and all crtcs mutexes act as the write
lock.
We'll also pimp intel_atomic_state_clear() to clear the entire global
state, so that we don't accidentally leak stale information between
the locking retries.
As a slight optimization we'll only lock the crtc mutexes to protect
the global state, however if and when we actually have to poke the
hw (eg. if the actual cdclk changes) we must serialize commits
across all crtcs so that a parallel nonblocking commit can't get
ahead of the cdclk reprogamming. We do that by adding all crtcs to
the state.
TODO: the old global state examined during commit may still
be a problem since it always looks at the _latest_ swapped state
in dev_priv. Need to add proper old/new state for that too I think.
v2: Remeber to serialize the commits if necessary
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
To make the logs a bit less confusing let's toss in some
debug prints to indicate whether the cdclk reprogramming
is going to happen with a single pipe active or whether we
need to turn all pipes off for the duration.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015193035.25982-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Replace sampling the engine state every so often with a periodic
heartbeat request to measure the health of an engine. This is coupled
with the forced-preemption to allow long running requests to survive so
long as they do not block other users.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023133108.21401-5-chris@chris-wilson.co.uk
DSC isn't DP specific, so remove the dp_ prefix from the crtc state
member name. Also moving the member under the dsc sub-struct gives us
enough context to allow shortening the name to just config. No
functional changes.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022133414.8293-2-jani.nikula@intel.com
Reduce verbosity in code by renaming dsc_params member of crtc state to
simply dsc. There is enough context for this to be clear. No functional
changes.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191022133414.8293-1-jani.nikula@intel.com
On ILK+ the documented min hdisplay is 64, min hblank is 32, and min
vblank is 5. On earlier platforms min hblank is also 32, and min
vblank is 3. Make sure the mode satisfies those limits.
There are further limits for HDMI and pfit use cases, but we'll check
for those in a more specific location.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718144340.1114-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
This way it's easier to figure out what didn't match when we have
multiple pipes enabled.
v2: pass drm_crtc and use the more common [CRTC:%d:%s] format
(Ville)
v3: use struct intel_crtc type to pass crtc around (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015164029.18431-5-lucas.demarchi@intel.com
Both Ice Lake and Elkhart Lake (gen 11) support MST on all external
connections except DDI A. Tiger Lake (gen 12) supports on all external
connections.
Move the check to happen inside intel_dp_mst_encoder_init() and add
specific platform checks.
v2: Replace != with == checks for ports on gen < 11 (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015164029.18431-3-lucas.demarchi@intel.com
In the transcoder port sync mode, the slave transcoders mask their vblanks
until master transcoder's vblank so while disabling them, make
sure slaves are disabled first and then the masters.
v5:
* Dont pass dev priv to get_slave_crtc (Ville)
v4:
* Obtain slave state from master (Maarten)
v3:
* Rebase
v2:
* Use the intel_old_crtc_state_disables() helper
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-6-manasi.d.navare@intel.com
This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2
register during crtc_disable().
v3:
* Rebase on maarten's patches
v2:
* Directly write the trans_port_sync reg value (Maarten)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-5-manasi.d.navare@intel.com
As per the display enable sequence, we need to follow the enable sequence
for slaves first with DP_TP_CTL set to Idle and configure the transcoder
port sync register to select the corersponding master, then follow the
enable sequence for master leaving DP_TP_CTL to idle.
At this point the transcoder port sync mode is configured and enabled
and the Vblanks of both ports are synchronized so then set DP_TP_CTL
for the slave and master to Normal and do post crtc enable updates.
v11:
* Rebase (Manasi)
v10:
* in trans sync mode, dont stop link train for tgl (Manasi)
v9:
Remove update_scanline_offset to rebase on Maarten's patch (Manasi)
v8:
* Rebase on Maarten's patches (Manasi)
v7:
* Use ffs(slaves) to get slave crtc (Ville)
v6:
* Modeset implies active_changed, remove one condition (Maarten)
v5:
* Fix checkpatch warning (Manasi)
v4:
* Reuse skl_commit_modeset_enables() hook (Maarten)
* Obtain slave crtc and states from master (Maarten)
v3:
* Rebase on drm-tip (Manasi)
v2:
* Create a icl_update_crtcs hook (Maarten, Danvet)
* This sequence only for CRTCs in trans port sync mode (Maarten)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-4-manasi.d.navare@intel.com
After the state is committed, we readout the HW registers and compare
the HW state with the SW state that we just committed.
For Transcdoer port sync, we add master_transcoder and the
salves bitmask to the crtc_state, hence we need to read those during
the HW state readout to avoid pipe state mismatch.
v11:
* Move master trans init to get pipe_Config hooks (Ville)
v10:
* Initialize master_tarnscoder readout for all platforms (Ville)
v9:
* Initialize master_transcoder = INVALID at get config (Ville)
v8:
* Use master_select -1, address TRANS_EDP case (Ville)
* Rename master_transcoder to _readout (Lucas)
v7:
* NDont read HW state for DSI
v6:
* Go through both parts of HW readout (Maarten)
* Add a WARN if the same trans configured as
master and slave (Ville, Maarten)
v5:
* Add return INVALID in defaut case (Maarten)
v4:
* Get power domains in master loop for get_config (Ville)
v3:
* Add TRANSCODER_D (Maarten)
* v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2:
* Add Transcoder_D and MISSING_CASE (Maarten)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-3-manasi.d.navare@intel.com
In case of tiled displays where different tiles are displayed across
different ports, we need to synchronize the transcoders involved.
This patch implements the transcoder port sync feature for
synchronizing one master transcoder with one or more slave
transcoders. This is only enbaled in slave transcoder
and the master transcoder is unaware that it is operating
in this mode.
This has been tested with tiled display connected to ICL.
v7:
* Rebase on Maarten's patches
v6:
* Use master_trans +1 and address missing trans_edp case (Ville)
v5:
* Add TRANSCODER_D case and MISSING_CASE (Maarten)
v4:
Rebase
v3:
* Check of DP_MST moved to atomic_check (Maarten)
v2:
* Do not use RMW, just write to the register in commit (Jani N)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-2-manasi.d.navare@intel.com
In case of tiled displays when the two tiles are sent across two CRTCs
over two separate DP SST connectors, we need a mechanism to synchronize
the two CRTCs and their corresponding transcoders.
So use the master-slave mode where there is one master corresponding
to last horizontal and vertical tile that needs to be genlocked with
all other slave tiles.
This patch identifies saves the master transcoder in all the slave
CRTC states. This is needed to select the master CRTC/transcoder
while configuring transcoder port sync for the corresponding slaves.
v6:
Rebase (manasi)
v5:
* Address Ville's comments
* Just pass crtc_state, no need to check GEN (Ville)
v4:
* Rebase
v3:
* Use master_tramscoder instead of master_crtc for valid
HW state readouts (Ville)
v2:
* Move this to intel_mode_set_pipe_config(Jani N, Ville)
* Use slave_bitmask to save associated slaves in master crtc state (Ville)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-1-manasi.d.navare@intel.com
All the timeout values fit in u16, so let's shrink the structure
a bit.
This ends up actually increasing the .text size a bit due to
some changes in instructions (constant imul+small jmps replaced
with mov+bigger jmpqs). Seems pretty arbitrary to me so I'll
just pretend I didn't see it.
text data bss dec hex filename
- 34521 360 0 34881 8841 intel_hdmi.o
+ 34537 360 0 34897 8851 intel_hdmi.o
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010145127.7487-5-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The only reason for the timeout2 value in the array is the
HDCP_2_2_AKE_SEND_HPRIME message. But that one still needs
special casing inside the loop, and so just ends up making
the code harder to read. Let's just remove this leaky
timeout2 abstraction and special case that one command
in a way that is easy to understand. We can then remove the
timeout2 member from struct entirely.
text data bss dec hex filename
- 34633 360 0 34993 88b1 intel_hdmi.o
+ 34521 360 0 34881 8841 intel_hdmi.o
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010145127.7487-4-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The .read_2_2() hooks is never called for any of the message
types with a zero timeout. So it's all just dead weight which
we can chuck.
text data bss dec hex filename
- 34701 360 0 35061 88f5 intel_hdmi.o
+ 34633 360 0 34993 88b1 intel_hdmi.o
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010145127.7487-3-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
The DP port/pipe goes wonky if we try to use timings with
hdisplay==4096 on pre-HSW platforms. The link fails to train
and the pipe may not signal vblank interrupts. On HDMI such at
mode works just fine (tested on ELK/SNB/CHV). So let's refuse
such modes on DP on older platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718144340.1114-1-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Replace the hand rolled stuff with drm_encoder_mask() when populating
possible_clones, and rename the function to
intel_encoder_possible_clones() to make it clear what it's used for.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-1-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Unlike other planes the cursor currently handles 180 degree rotation
adjustment during the hardware programming phase. Let's move that
stuff into intel_cursor_check_surface() to match how we do things
with other plane types.
And while at we'll plop in the final src x/y coordinates (which will
actually always be zero) into the src rect and color_plane[0].x/y,
just for some extra consistency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015152757.12231-1-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
The MSA MISC computation now depends on the connector state, and
we do it from the DDI .pre_enable() hook. All that is fine for
DP SST but with MST we don't actually pass the connector state
to the dig port's .pre_enable() hook which leads to an oops.
Need to think more how to solve this in a cleaner fashion, but
for now let's just add a NULL check to stop the oopsing.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 0c06fa1560 ("drm/i915/dp: Add support of BT.2020 Colorimetry to DP MSA")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191015190538.27539-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
The first come first served apporoach to handling the VBT
child device AUX ch conflicts has backfired. We have machines
in the wild where the VBT specifies both port A eDP and
port E DP (in that order) with port E being the real one.
So let's try to flip the preference around and let the last
child device win once again.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Masami Ichikawa <masami256@gmail.com>
Tested-by: Torsten <freedesktop201910@liggy.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111966
Fixes: 36a0f92020 ("drm/i915/bios: make child device order the priority order")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011202030.8829-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 41e35ffb38)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Once we do the hw vs. uapi split we can no longer use
drm_atomic_helper_calc_timestamping_constants() as it'll
consult the uapi state instead of the hw state.
So let's just update the vblank timestamping constants whenever
we update the scanline offset. We use both to convert the hw
scanline count to something which matches the software timing
values.
First I thought to put these into intel_crtc_vblank_on() but
we may want to get the scanline counter value before that (eg.
from some early tracepoints), so let's stick to updating them
a bit earlier than intel_crtc_vblank_on().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007114943.29307-3-ville.syrjala@linux.intel.com
While not all platforms allow us to change the cdclk frequency
we should still verify that the fixed cdclk frequency isn't
too low. To that end let's cook up a .modeset_calc_cdclk()
implementation that only does the min_cdclk vs. actual cdclk
frequency check for such platforms.
Also we mustn't forget about double wide pipe on gen2/3 when
doing this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708125325.16576-11-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We need to insert stuff between the plane and crtc .atomic_check()
drm_atomic_helper_check_planes() doesn't allow us to do that so
stop using it and hand roll the loops instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708125325.16576-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
It attaches HDR metadata property to DP connector on GLK+.
It enables HDR metadata infoframe sdp on GLK+ to be used to send
HDR metadata to DP sink.
v2: Minor style fix
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-9-gwan-gyeong.mun@intel.com
Function intel_dp_setup_hdr_metadata_infoframe_sdp handles Infoframe SDP
header and data block setup for HDR Static Metadata. It enables writing of
HDR metadata infoframe SDP to panel. Support for HDR video was introduced
in DisplayPort 1.4. It implements the CTA-861-G standard for transport of
static HDR metadata. The HDR Metadata will be provided by userspace
compositors, based on blending policies and passed to the driver through
a blob property.
Because each of GEN11 and prior GEN11 have different register size for
HDR Metadata Infoframe SDP packet, it adds and uses different register
size.
Setup Infoframe SDP header and data block in function
intel_dp_setup_hdr_metadata_infoframe_sdp for HDR Static Metadata as per
dp 1.4 spec and CTA-861-F spec.
As per DP 1.4 spec, 2.2.2.5 SDP Formats. It enables Dynamic Range and
Mastering Infoframe for HDR content, which is defined in CTA-861-F spec.
According to DP 1.4 spec and CEA-861-F spec Table 5, in order to transmit
static HDR metadata, we have to use Non-audio INFOFRAME SDP v1.3.
+--------------------------------+-------------------------------+
| [ Packet Type Value ] | [ Packet Type ] |
+--------------------------------+-------------------------------+
| 80h + Non-audio INFOFRAME Type | CEA-861-F Non-audio INFOFRAME |
+--------------------------------+-------------------------------+
| [Transmission Timing] |
+----------------------------------------------------------------+
| As per CEA-861-F for INFOFRAME, including CEA-861.3 within |
| which Dynamic Range and Mastering INFOFRAME are defined |
+----------------------------------------------------------------+
v2: Add a missed blank line after function declaration.
v3: Remove not handled return values from
intel_dp_setup_hdr_metadata_infoframe_sdp(). [Uma]
v9: Addressed review comments from Ville.
- Add BUILD_BUG_ON to check a changing of struct dp_sdp size.
- Change a passed size toward write_infoframe() for DP infoframe sdp
packet for HDR static metadata.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-8-gwan-gyeong.mun@intel.com
According to Bspec, GEN11 and prior GEN11 have different register size for
HDR Metadata Infoframe SDP packet. It adds new VIDEO_DIP_GMP_DATA_SIZE for
GEN11. And it makes handle different register size for
HDMI_PACKET_TYPE_GAMUT_METADATA on hsw_dip_data_size() for each GEN
platforms. It addresses Uma's review comments.
v9: Add WARN_ON() when buffer size if larger than register size. [Ville]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-7-gwan-gyeong.mun@intel.com
It attaches the colorspace connector property to a DisplayPort connector.
Based on colorspace change, modeset will be triggered to switch to a new
colorspace.
And in order to distinguish colorspace bwtween DP and HDMI connector, it
adds a handling of drm_mode_create_dp_colorspace_property() to
intel_attach_colorspace_property().
Based on colorspace property value create a VSC SDP packet with appropriate
colorspace. This would help to enable wider color gamut like BT2020 on a
sink device.
v9: Addressed review comments from Ville
- Add a handling of drm_mode_create_dp_colorspace_property() to
intel_attach_colorspace_property(). This hunk moved from the previous
commit.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-6-gwan-gyeong.mun@intel.com
When BT.2020 Colorimetry output is used for DP, we should program BT.2020
Colorimetry to MSA and VSC SDP. In order to handle colorspace of
drm_connector_state, it moves a calling of intel_ddi_set_pipe_settings()
function into intel_ddi_pre_enable_dp(). And it also rename
intel_ddi_set_pipe_settings() to intel_ddi_set_dp_msa().
As per DP 1.4a spec section 2.2.4 [MSA Data Transport]
The MSA data that the DP Source device transports for reproducing the main
video stream. Attribute data is sent once per frame during the main video
stream’s vertical blanking period.
In order to distinguish needed colorimetry for VSC SDP, it adds
intel_dp_needs_vsc_sdp function.
If the output colorspace requires vsc sdp or output format is YCbCr 4:2:0,
it uses MSA with VSC SDP.
As per DP 1.4a spec section 2.2.4.3 [MSA Field for Indication of
Color Encoding Format and Content Color Gamut] while sending
BT.2020 Colorimetry signals we should program MSA MISC1 fields which
indicate VSC SDP for the Pixel Encoding/Colorimetry Format.
v2: Remove useless parentheses
v3: Addressed review comments from Ville
- In order to checking output format and output colorspace on
intel_dp_needs_vsc_sdp(), it passes entire intel_crtc_state struct
value.
- Remove a pointless variable.
v9: Addressed review comments from Ville
- Remove a duplicated output color space from intel_crtc_state.
- In order to handle colorspace of drm_connector_state, it moves a
calling of intel_ddi_set_pipe_settings() function into
intel_ddi_pre_enable_dp().
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-3-gwan-gyeong.mun@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
It refactors and renames a function which handled vsc sdp header and data
block setup for supporting colorimetry format.
Function intel_dp_setup_vsc_sdp handles vsc sdp header and data block
setup for pixel encoding / colorimetry format.
In order to use colorspace information of a connector, it adds an argument
of drm_connector_state type.
Setup VSC header and data block in function intel_dp_setup_vsc_sdp for
pixel encoding / colorimetry format as per dp 1.4a spec, section 2.2.5.7.1,
table 2-119: VSC SDP Header Bytes, section 2.2.5.7.5,
table 2-120: VSC SDP Payload for DB16 through DB18.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-2-gwan-gyeong.mun@intel.com
On platforms that have the MCC PCH, Port C's hotplug interrupt
bits are mapped to TC1 bits.
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011002618.3087-1-vivek.kasireddy@intel.com
The first come first served apporoach to handling the VBT
child device AUX ch conflicts has backfired. We have machines
in the wild where the VBT specifies both port A eDP and
port E DP (in that order) with port E being the real one.
So let's try to flip the preference around and let the last
child device win once again.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Masami Ichikawa <masami256@gmail.com>
Tested-by: Torsten <freedesktop201910@liggy.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111966
Fixes: 36a0f92020 ("drm/i915/bios: make child device order the priority order")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011202030.8829-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Just a parameter rename,
drivers/gpu/drm/i915/display/intel_display.c:14425: warning: Function parameter or member '_new_plane_state' not described in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14425: warning: Excess function parameter 'new_state' description in 'intel_prepare_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14534: warning: Function parameter or member '_old_plane_state' not described in 'intel_cleanup_plane_fb'
drivers/gpu/drm/i915/display/intel_display.c:14534: warning: Excess function parameter 'old_state' description in 'intel_cleanup_plane_fb'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191012080208.18774-1-chris@chris-wilson.co.uk
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl2d9h8ACgkQcywAJXLc
r3ms5gf9HIFpqwJ16CqaRukSnpcBcDoYUM8DGrOic+vw2bw14BQwFqvEOqrCkKL4
V6h/OCJlNFPtOcc1LvU/jeXxYf4AQWh/2qZeg+oee7HAGX5x8Y3f08GsEjO8+55t
QvSVxCKVti04M1ErPRfKrM7KPVE+IC+KdY26nO8Bf5zDGeCAkiPIDrdh2aZGMRdC
Eer0DJ96cgWW9LrhseCdj5nKwcR78DlbWa79zuPAss4LaBBbXqThNXYYzg/mZMKB
+VYgzs48tGYKK1NXXJ6biVI3brHrM52bqv5JpIncD5HepF1oIartWOMnbAO7MAqh
h/tgJWxL+4bnl9aqY87by1BtyVgl3w==
=kaOE
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-10-09-2' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-Colorspace: Expose different prop values for DP vs. HDMI (Gwan-gyeong Mun)
-fourcc: Add DRM_FORMAT_MOD_ARM_16X16_BLOCK_U_INTERLEAVED (Raymond)
-not_actually: s/ENOTSUPP/EOPNOTSUPP/ in drm_edid and drm_mipi_dbi. This should
not reach userspace, but adding here to specifically call that out (Daniel)
-i810: Prevent underflow in dispatch ioctls (Dan)
-komeda: Add ACLK sysfs attribute (Mihail)
-v3d: Allow userspace to clean up after render jobs (Iago)
Cross-subsystem Changes:
-MAINTAINERS:
-Add Alyssa & Steven as panfrost reviewers (Rob)
-Add Jernej as DE2 reviewer (Maxime)
-Add Chen-Yu as Allwinner maintainer (Maxime)
-staging: Make some stack arrays static const (Colin)
Core Changes:
-ttm: Allow drivers to specify their vma manager (to use gem mgr) (Gerd)
-docs: Various fixes in connector/encoder/bridge docs (Daniel, Lyude, Laurent)
-connector: Allow more than 3 possible encoders for a connector (José)
-dp_cec: Allow a connector to be associated with a cec device (Dariusz)
-various: Fix some compile/sparse warnings (Ville)
-mm: Ensure mm node removals are properly serialised (Chris)
-panel: Specify the type of panel for drm_panels for later use (Laurent)
-panel: Use drm_panel_init to init device and funcs (Laurent)
-mst: Refactors and cleanups in anticipation of suspend/resume support (Lyude)
-vram:
-Add lazy unmapping for gem bo's (Thomas)
-Unify and rationalize vram mm and gem vram (Thomas)
-Expose vmap and vunmap for gem vram objects (Thomas)
-Allow objects to be pinned at the top of vram to avoid fragmentation (Thomas)
Driver Changes:
-various: Include drm_bridge.h instead of relying on drm_crtc.h (Boris)
-ast/mgag200: Refactor show_cursor(), move cursor to top of video mem (Thomas)
-komeda:
-Add error event printing (behind CONFIG) and reg dump support (Lowry)
-Add suspend/resume support (Lowry)
-Workaround D71 shadow registers not flushing on disable (Lowry)
-meson: Add suspend/resume support (Neil)
-omap: Miscellaneous refactors and improvements (Tomi/Jyri)
-panfrost/shmem: Silence lockdep by using mutex_trylock (Rob)
-panfrost: Miscellaneous small fixes (Rob/Steven)
-sti: Fix warnings (Benjamin/Linus)
-sun4i:
-Add vcc-dsi regulator to sun6i_mipi_dsi (Jagan)
-A few patches to figure out the DRQ/start delay calc on dsi (Jagan/Icenowy)
-virtio:
-Add module param to switch resource reuse workaround on/off (Gerd)
-Avoid calling vmexit while holding spinlock (Gerd)
-Use gem shmem helpers instead of ttm (Gerd)
-Accommodate command buffer allocations too big for cma (David)
Cc: Rob Herring <robh@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Raymond Smith <raymond.smith@arm.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Lowry Li <Lowry.Li@arm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Iago Toral Quiroga <itoral@igalia.com>
Cc: David Riley <davidriley@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 10 Oct 2019 01:00:47 AM AEST
# gpg: using RSA key 732C002572DCAF79
# gpg: Can't check signature: public key not found
# Conflicts:
# drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c
# drivers/gpu/drm/i915/i915_drv.c
# drivers/gpu/drm/i915/i915_gem.c
# drivers/gpu/drm/i915/i915_gem_gtt.c
# drivers/gpu/drm/i915/i915_vma.c
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009150825.GA227673@art_vandelay
We have a src and dect rectangle, use it instead of relying on
the core drm properties.
Because the core by default clips the src/dst properties, after
the drm_atomic_helper_check_plane_state() we manually set the
unclipped src/dst rectangles. We still need the call for
visibility checks, but this way we are able to use the src/dst
rects in the check/commit code.
This removes the special case in the watermark code for cursor w/h.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-5-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Clarify commit message to state we use unclipped src/dst
This can all be done from the intel_update_crtc function. Split out the
pipe update into a separate function, just like is done for the planes.
Pull in all the changes done during fastset as well. It makes no sense
for it to still exist as a separate function.
Changes since v1:
- Inline intel_update_pipe_config()
Changes since v2:
- Add comments suggested by matt.
- Reorder commit_pipe_config() to remove all nesting. (Ville, Matt)
- Use intel_set_pipe_src_size((). (Matt)
Changes since v3:
- Move atomic_update_watermarks closer to the plane calls.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Replace 8 spaces with tabs in comment]
We need to look at the hw fb in the plane split, so replace all the places
that use drm_plane_state with intel_plane_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Fix line wraps (Matt Roper)]
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Instead of looking at drm_plane_state, look at intel_plane_state directly.
This will allow us to make the watermarks bigjoiner aware, when we make it
work for bigjoiner slave pipes as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-4-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Using for_each_intel_plane_mask() fails because of an extra bracket,
remove the bracket so we can use it in the next commit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004113514.17064-3-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
This slightly simplifies the EHL DPLL4 handling and also gives us more
flexibility in the future in case we need to skip the use of specific
PLL's (e.g., due to hardware workarounds and such).
v2:
- Replace GENMASK() with or'd BIT()'s to make the specific DPLLs more
explicit. (Ville)
- s/unsigned/unsigned long/. (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008172920.11362-1-matthew.d.roper@intel.com
Moved common code to check gamma_enable to specific funcs per platform
in bit_precision func. icl doesn't support that and chv has separate
enable knob for CGM LUT.
v2:
-Simplified chv_gamma_precision() [Ville]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009065542.27415-3-swati2.sharma@intel.com
Premature gamma lut prepration and loading which was getting
reflected in first modeset causing different colors on
screen during boot.
Issue: In BIOS, gamma is disabled by default. However, legacy read_luts()
was setting crtc_state->base.gamma_lut and gamma_lut was programmed
with junk values which led to visual artifacts (different
colored screens instead of usual black during boot).
Fix: Calling read_luts() only when gamma is enabled which will happen
after first modeset.
This fix is independent from the revert 1b8588741f ("Revert
"drm/i915/color: Extract icl_read_luts()"") and should fix different colors
on screen in legacy platforms too.
v2:
-Added gamma_enable checks inside read_luts() [Ville/Jani N]
-Corrected gamma enable check for CHV [Ville]
v3:
-Added check in ilk_read_luts() [Ville]
-Simplified gamma enable check for CHV [Ville]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111809
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111885
Tested-by: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009065542.27415-2-swati2.sharma@intel.com
DC3CO is useful power state, when DMC detects PSR2 idle frame
while an active video playback, playing 30fps video on 60hz panel
is the classic example of this use case.
B.Specs:49196 has a restriction to enable DC3CO only for Video Playback.
It will be worthy to enable DC3CO after completion of each pageflip
and switch back to DC5 when display is idle because driver doesn't
differentiate between video playback and a normal pageflip.
We will use Frontbuffer flush call tgl_dc3co_flush() to enable DC3CO
state only for ORIGIN_FLIP flush call, because DC3CO state has primarily
targeted for VPB use case. We are not interested here for frontbuffer
invalidates calls because that triggers PSR2 exit, which will
explicitly disable DC3CO.
DC5 and DC6 saves more power, but can't be entered during video
playback because there are not enough idle frames in a row to meet
most PSR2 panel deep sleep entry requirement typically 4 frames.
As PSR2 existing implementation is using minimum 6 idle frames for
deep sleep, it is safer to enable DC5/6 after 6 idle frames
(By scheduling a delayed work of 6 idle frames, once DC3CO has been
enabled after a pageflip).
After manually waiting for 6 idle frames DC5/6 will be enabled and
PSR2 deep sleep idle frames will be restored to 6 idle frames, at this
point DMC will triggers DC5/6 once PSR2 enters to deep sleep after
6 idle frames.
In future when we will enable S/W PSR2 tracking, we can change the
PSR2 required deep sleep idle frames to 1 so DMC can trigger the
DC5/6 immediately after S/W manual waiting of 6 idle frames get
complete.
v2: calculated s/w state to switch over dc3co when there is an
update. [Imre]
Used cancel_delayed_work_sync() in order to avoid any race
with already scheduled delayed work. [Imre]
v3: Cancel_delayed_work_sync() may blocked the commit work.
hence dropping it, dc5_idle_thread() checks the valid wakeref before
putting the reference count, which avoids any chances of dropping
a zero wakeref. [Imre (IRC)]
v4: Used frontbuffer flush mechanism. [Imre]
v5: Used psr.pipe to extract frontbuffer busy bits. [Imre]
Used cancel_delayed_work_sync() in encoder disable path. [Imre]
Used mod_delayed_work() instead of cancelling and scheduling a
delayed work. [Imre]
Used psr.lock in tgl_dc5_idle_thread() to enable psr2 deep
sleep. [Imre]
Removed DC5_REQ_IDLE_FRAMES macro. [Imre]
v6: Used dc3co_exitline check instead of TGL and dc3co allowed_dc_mask
checks, used delayed_work_pending with the psr lock and removed the
psr2_deep_slp_disabled flag. [Imre]
v7: Code refactoring, moved most of functional code to inte_psr.c [Imre]
Using frontbuffer_bits on psr.pipe check instead of
busy_frontbuffer_bits. [Imre]
Calculating dc3co_exit_delay in intel_psr_enable_locked. [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-6-anshuman.gupta@intel.com
DC3CO enabling B.Specs sequence requires to enable end configure
exit scanlines to TRANS_EXITLINE register, programming this register
has to be part of modeset sequence as this can't be change when
transcoder or port is enabled.
When system boots with only eDP panel there may not be real
modeset as BIOS has already programmed the necessary registers,
therefore it needs to force a modeset to enable and configure
DC3CO exitline.
v1: Computing dc3co_exitline crtc state from a DP encoder
compute config. [Imre]
Enabling and disabling DC3CO PSR2 transcoder exitline from
encoder pre_enable and post_disable hooks. [Imre]
Computing dc3co_exitline instead of has_dc3co_exitline bool. [Imre]
v2: Code refactoring for symmetry and to avoid exported function. [Imre]
Removing IS_TIGERLAKE check from compute_config, adding PIPE_A
restriction and clearing dc3co_exitline state if crtc is not active
or it is not PSR2 capable in dc3co exitline compute_config. [Imre]
Using GEN >= 12 check in dc3co exitline get_config. [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-5-anshuman.gupta@intel.com
Add target_dc_state and used by set_target_dc_state API
in order to enable DC3CO state with existing DC states.
target_dc_state will enable/disable the desired DC state in
DC_STATE_EN reg when "DC Off" power well gets disable/enable.
v2: commit log improvement.
v3: Used intel_wait_for_register to wait for DC3CO exit. [Imre]
Used gen9_set_dc_state() to allow/disallow DC3CO. [Imre]
Moved transcoder psr2 exit line enablement from tgl_allow_dc3co()
to a appropriate place haswell_crtc_enable(). [Imre]
Changed the DC3CO power well enabled call back logic as
recommended in review comments. [Imre]
v4: Used wait_for_us() instead of intel_wait_for_reg(). [Imre (IRC)]
v5: using udelay() instead of waiting for DC3CO exit status.
v6: Fixed minor unwanted change.
v7: Removed DC3CO powerwell and POWER_DOMAIN_VIDEO.
v8: Uniform checks by using only target_dc_state instead of allowed_dc_mask
in "DC off" power well callback. [Imre]
Adding "DC off" power well id to older platforms. [Imre]
Removed psr2_deep_sleep flag from tgl_set_target_dc_state. [Imre]
v9: Used switch case for target DC state in
gen9_dc_off_power_well_disable(), checking DC3CO state against
allowed DC mask, using WARN_ON() in
tgl_set_target_dc_state(). [Imre]
v10: Code refactoring and using sanitize_target_dc_state(). [Imre]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-4-anshuman.gupta@intel.com
Enable dc3co state in enable_dc module param and add dc3co
enable mask to allowed_dc_mask and gen9_dc_mask.
v1: Adding enable_dc=3,4 options to enable DC3CO with DC5 and DC6
independently. [Animesh]
v2: Using a switch statement for cleaner code. [Animesh]
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003081738.22101-3-anshuman.gupta@intel.com
The officially validated plane width limit is 4k on skl+, however
we already had people using 5k displays before we started to enforce
the limit. Also it seems Windows allows 5k resolutions as well
(though not sure if they do it with one plane or two).
According to hw folks 5k should work with the possible
exception of the following features:
- Ytile (already limited to 4k)
- FP16 (already limited to 4k)
- render compression (already limited to 4k)
- KVMR sprite and cursor (don't care)
- horizontal panning (need to verify this)
- pipe and plane scaling (need to verify this)
So apart from last two items on that list we are already
fine. We should really verify what happens with those last
two items but I don't have a 5k display on hand atm so it'll
have to wait.
In the meantime let's just bump the limit back up to 5k since
several users have already been using it without apparent issues.
At least we'll be no worse off than we were prior to lowering
the limits.
Cc: stable@vger.kernel.org
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Leho Kraav <leho@kraav.com>
Fixes: 372b9ffb57 ("drm/i915: Fix skl+ max plane width")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111501
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190905135044.2001-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
(cherry picked from commit bed34ef544)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The latest documented version of the VBT is 229, but no further data has
been added to the child device definition in block 2. Update the child
device version test to eliminate the "Expected child device config size
for VBT version XXX not known; assuming 39" debug messages from the
logs.
Bspec: 20124
Bspec: 20157
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002192258.1013-1-matthew.d.roper@intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pair the gmbus setup and teardown in the same layer. This also fixes the
double gmbus teardown on the i915_driver_modeset_probe() error path.
Move the gmbus setup a bit later in the sequence to make the follow-up
refactoring easier, and to pinpoint any unexpected consequences of this
change right here, instead of the later refactoring.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004122019.12009-3-jani.nikula@intel.com
Rename the function per Ville's suggestion. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004122019.12009-1-jani.nikula@intel.com
Our other backends return an actual error value upon failure. Do the
same for stolen objects, which currently just return NULL on failure.
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004170452.15410-2-matthew.auld@intel.com
The current "disable C3+" workaround for the delayed vblank
irqs on i945gm no longer works. I'm not sure what changed, but
now I need to also disable C2. I also got my hands on a i915gm
machine that suffers from the same issue.
After some furious poking of registers I managed to find a
better workaround: The "Do not Turn off Core Render Clock in C
states" bit. With that I no longer have to disable any C-states,
and as a nice bonus the power cost is only ~1/4 of the
"disable C3+" method (which mind you doesn't even work anymore,
and so would have an even higher power cost if we made it work
by also disabling C2).
So let's throw out all the cpuidle/qos crap and just toggle
the magic bit as needed. And we extend the workaround to cover
i915gm as well.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003140231.24408-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Forgo the struct_mutex serialisation for i915_active, and interpose its
own mutex handling for active/retire.
This is a multi-layered sleight-of-hand. First, we had to ensure that no
active/retire callbacks accidentally inverted the mutex ordering rules,
nor assumed that they were themselves serialised by struct_mutex. More
challenging though, is the rule over updating elements of the active
rbtree. Instead of the whole i915_active now being serialised by
struct_mutex, allocations/rotations of the tree are serialised by the
i915_active.mutex and individual nodes are serialised by the caller
using the i915_timeline.mutex (we need to use nested spinlocks to
interact with the dma_fence callback lists).
The pain point here is that instead of a single mutex around execbuf, we
now have to take a mutex for active tracker (one for each vma, context,
etc) and a couple of spinlocks for each fence update. The improvement in
fine grained locking allowing for multiple concurrent clients
(eventually!) should be worth it in typical loads.
v2: Add some comments that barely elucidate anything :(
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004134015.13204-6-chris@chris-wilson.co.uk
As we need to use a mutex to serialise i915_active activation
(because we want to allow the callback to sleep), we need to push the
i915_active.retire into a worker callback in case we get need to retire
from an atomic context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004134015.13204-5-chris@chris-wilson.co.uk
Replace the struct_mutex requirement for pinning the i915_vma with the
local vm->mutex instead. Note that the vm->mutex is tainted by the
shrinker (we require unbinding from inside fs-reclaim) and so we cannot
allocate while holding that mutex. Instead we have to preallocate
workers to do allocate and apply the PTE updates after we have we
reserved their slot in the drm_mm (using fences to order the PTE writes
with the GPU work and with later unbind).
In adding the asynchronous vma binding, one subtle requirement is to
avoid coupling the binding fence into the backing object->resv. That is
the asynchronous binding only applies to the vma timeline itself and not
to the pages as that is a more global timeline (the binding of one vma
does not need to be ordered with another vma, nor does the implicit GEM
fencing depend on a vma, only on writes to the backing store). Keeping
the vma binding distinct from the backing store timelines is verified by
a number of async gem_exec_fence and gem_exec_schedule tests. The way we
do this is quite simple, we keep the fence for the vma binding separate
and only wait on it as required, and never add it to the obj->resv
itself.
Another consequence in reducing the locking around the vma is the
destruction of the vma is no longer globally serialised by struct_mutex.
A natural solution would be to add a kref to i915_vma, but that requires
decoupling the reference cycles, possibly by introducing a new
i915_mm_pages object that is own by both obj->mm and vma->pages.
However, we have not taken that route due to the overshadowing lmem/ttm
discussions, and instead play a series of complicated games with
trylocks to (hopefully) ensure that only one destruction path is called!
v2: Add some commentary, and some helpers to reduce patch churn.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004134015.13204-4-chris@chris-wilson.co.uk
On platfroms with gen10+ display, driver must set the enable bit of
AUDIO_PIN_BUF_CTL register before transactions with the HDA controller
can proceed. Add setting this bit to the audio power up sequence.
Failing to do this resulted in errors during display audio codec probe,
and failures during resume from suspend.
Note: We may also need to disable the bit afterwards, but there are
still unresolved issues with that.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111214
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003085531.30990-1-kai.vehmanen@linux.intel.com
Add aux_busy_last_status to intel_dp. Don't bother with initializing to
all ones; the only difference is potentially missing logging for one
error case if the readout is all zeros.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002144138.7917-1-jani.nikula@intel.com
The Thunderbolt PLL divider values on TGL differ from the ICL ones,
update the PLL parameter calculation function accordingly.
Bspec: 49204
v2:
- Remove unused refclk config. (José)
Cc: Jose Souza <jose.souza@intel.com>
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jose Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002204108.32242-1-imre.deak@intel.com
This reverts commit 4eaceea3a0.
Several userspace clients (modesetting ddx and mutter+wayland at least)
handle encoder.possible_crtcs incorrectly. What they essentially do is
the following:
possible_crtcs = ~0;
for_each_possible_encoder(connector)
possible_crtcs &= encoder->possible_crtcs;
Ie. they calculate the intersection of the possible_crtcs
for the connector when they really should be calculating the
union instead.
In our case each MST encoder now has just one unique bit set,
and so the intersection is always zero. The end result is that
MST connectors can't be lit up because no crtc can be found to
drive them.
I've submitted a fix for the modesetting ddx [1], and complained
on #wayland about mutter, so hopefully the situation will improve
in the future. In the meantime we have regression, and so must go
back to the old way of misconfiguring possible_crtcs in the kernel.
[1] https://gitlab.freedesktop.org/xorg/xserver/merge_requests/277
Cc: Jonas Ådahl <jadahl@gmail.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111507
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903154018.26357-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit e838bfa8e1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
I forgot to update the g4x sprite scaling stride check when GTT
remapping was introduced. The stride of the original framebuffer
is irrelevant when remapping is used and instead we want to check
the stride of the remapped view.
Also drop the duplicate width_bytes check. We already check that
a few lines earlier.
Fixes: df79cf4419 ("drm/i915: Store the final plane stride in plane_state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930183045.662-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 006e570128)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width
limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit ed06efb801)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
All the MG registers is based on the tc_port not port, so
MG_PHY_PORT_LN() was subtracting port and PORT_C what is very
fragile.
So replacing port to tc_port in all MG register macros and users
like we have for DKL.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001193729.123736-1-jose.souza@intel.com
I forgot to update the g4x sprite scaling stride check when GTT
remapping was introduced. The stride of the original framebuffer
is irrelevant when remapping is used and instead we want to check
the stride of the remapped view.
Also drop the duplicate width_bytes check. We already check that
a few lines earlier.
Fixes: df79cf4419 ("drm/i915: Store the final plane stride in plane_state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930183045.662-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Drop the tv_mode NULL check since intel_tv_mode_find() never
actually returns NULL, and flip the condition around so that
the MODE_OK case is at the end, which is customary to all
the other .mode_valid() implementations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
When adding the max plane size checks to the .mode_valid() hooks
I naturally forgot about MST. Take care of that one as well.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 2d20411e25 ("drm/i915: Don't advertise modes that exceed the max plane size")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Split out the code related to vga client and vgaarb all over the place
into new intel_vga.[ch]. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001152506.7854-1-jani.nikula@intel.com
As we execute GPU resets on a gt/ basis, and use the intel_gt as the
primary for all other reset functions, also use it for the has-reset?
predicates. Gradually simplifying the churn of pointers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927211749.2181-1-chris@chris-wilson.co.uk
Now that TC support was added, initialize DDIs.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-4-jose.souza@intel.com
Link training is failling when running link at 2.7GHz and 1.62GHz and
following BSpec pll algorithm.
Comparing the values calculated and the ones from the reference table
it looks like MG_CLKTOP2_CORECLKCTL1_A_DIVRATIO should not always set
to 5. For DP ports ICL mg pll algorithm sets it to 10 or 5 based on
div2 value, that matches with dkl hardcoded table.
So implementing this way as it proved to work in HW and leaving a
comment so we know why it do not match BSpec.
v4:
Using the same is_dp check as ICL, need testing on HDMI over tc port
Issue reported on BSpec 49204.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-3-jose.souza@intel.com
Added DKL Phy sequences and helpers functions to program voltage
swing, clock gating and dp mode.
It is not written in DP enabling sequence but "PHY Clockgating
programming" states that clock gating should be enabled after the
link training but doing so causes all the following trainings to fail
so not enabling it for.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Adding the meaning of each column of tgl_dkl_phy_ddi_translations
Adding if gen >= 12 on intel_ddi_hdmi_level() and
intel_ddi_pre_enable_hdmi() instead of reuse part of gen >= 11 if
v4:
Moved the DP_MODE lane programing to another patch as ICL also
needed it
Sharing icl_phy_set_clock_gating() and icl_program_mg_dp_mode() with
TGL as bits and programing as now it almost identical to ICL
BSpec: 49292
BSpec: 49190
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-2-jose.souza@intel.com
BSpec was updated(r146548) with a new MG_DP_MODE Programming table,
now taking in consideration the pin assignment and allowing us to
optimize power by shutting down available but not needed lanes.
It was tested on ICL and TGL, with adaptors that used pin assignment
C and B, reversing the connector and going to different modes testing
the not needed lane shutdown.
v5:
Using crtc_state->lane_count instead of dp.lane_count
BSpec: 21735
BSpec: 49292
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-1-jose.souza@intel.com
According to the bspec, GLK/CNL have a smaller small joiner RAM buffer
than ICL+. This feels like something that could easily change again on
future platforms, so let's just add a function to return the proper
per-platform buffer size. That may also slightly simplify the upcoming
bigjoiner enabling.
Since we have to change intel_dp_dsc_get_output_bpp()'s signature to
pass the dev_priv down for the platform check, let's take the
opportunity to also make that function static since it isn't used
outside the intel_dp file.
v2: Minor rebase on top of Maarten's changes.
Bspec: 20388
Bspec: 49259
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925234542.24289-1-matthew.d.roper@intel.com
The memory type values have changed in TGL, so we need to translate them
differently than ICL. While we're moving it, fix up the ICL translation
for LPDDR4.
BSpec: 53998
v2: Fix up ICL LPDDR4 entry (Ville); Drop unused values from TGL (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924222829.13142-1-james.ausmus@intel.com
TGL added 2 more TC ports that currently are not being handled by
icl_pll_to_ddi_clk_sel(), so adding those.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-6-jose.souza@intel.com
Extending ICL mg calculations to also support dkl calculations.
v3:
Fixing iref_trim calculation for 38400 refclock
BSpec: 49204
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-5-jose.souza@intel.com
The final save operation into pll_state of the calculations done will
be different for DKL PHY. Prepare for that by reindenting code so it's
easier to check for correctness. This one has no change in behavior.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-4-jose.souza@intel.com
Add a new function to write to dkl phy pll registers. As per the
bspec all the registers are read modify write.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-2-jose.souza@intel.com
The disable function can be the same as for MG phy since the same
registers are used. The others are different as registers changed,
also adding a empty dkl_pll_write() to be implemented later.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Masking non-computed registers of mg_pll_tdc_coldst_bias
when getting hardware state
Sharing mg_pll_enable() with TGL
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-1-jose.souza@intel.com
We cannot switch between HQ and normal mode on GLK+, so only
add planes on platforms where it makes sense.
We could probably restrict it even more to only add when scaler
users toggles between 1 and 2, but lets just leave it for now.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-9-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
We had this as an optimization to not do a plane update, but we killed
it off because there are so many reasons we may have to do a plane
update or fastset that it's best to just assume everything changed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width
limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Added bandwidth calculation algorithm and checks,
similar way as it was done for ICL, some constants
were corrected according to BSpec 53998.
v2: Start using same icl_get_bw_info function to avoid
code duplication. Moved mpagesize to memory info
related structure as it is now dependent on memory type.
Fixed qi.t_bl field assignment.
v3: Removed mpagesize as unused. Duplicate code and redundant blankline
fixed.
v4: Changed ordering of IS_GEN checks as agreed. Minor commit
message fixes.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111600
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920083754.5920-1-stanislav.lisovskiy@intel.com
Adding a enable parameters allow us to share most of the code between
enable and disable functions.
v3:
Renamed icl_phy_clock_gating() to icl_phy_set_clock_gating()
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-6-jose.souza@intel.com
Commit 24a7bfe0c2 ("drm/i915: Keep the TypeC port mode fixed when the
port is active") added this new hook while in parallel TGL upstream was
happening and this was missed.
Without this driver will crash when TC DDI is added and driver is
preparing to do a full modeset.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-4-jose.souza@intel.com
If platform supports and has modular FIA is enabled, the registers
bits also change, example: reading TC3 registers with modular FIA
enabled, driver should read from FIA2 but with TC1 bits offsets.
It is described in BSpec 50231 for DFLEXDPSP, other registers don't
have the BSpec description but testing in real hardware have proven
that it had moved for all other registers too.
v2:
- Caching index in tc_phy_fia_idx, instead of calculate it each time
v3:
- Setting tc_phy_fia and tc_phy_fia_idx in the same function
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-3-jose.souza@intel.com
Step 4.b was complete missed because it is only required to TC and TBT.
Bspec: 49190
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-2-jose.souza@intel.com
The i915 specific mode config init code is too specific and detailed to
have open in a high level function. Abstract away. No functional
changes.
v2: nest drm_mode_config_init() in the function too (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-5-jani.nikula@intel.com
The code is too specific and detailed to have open in a high level
function. Abstract away. As a drive-by improvement switch to using
enableddisabled() in logging and git rid of a redundant !!. No
functional changes.
v2: drop the !! while at it too (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-4-jani.nikula@intel.com
In general, prefer struct drm_i915_private * over struct drm_device *
when either will do. Rename the local variable to i915. Also propagate
to intel_hpd_poll_fini(). No functional changes.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920185421.17822-3-jani.nikula@intel.com
When audio power domain is suspended, the display driver must
save state of AUD_FREQ_CNTRL on Tiger Lake and Ice Lake
systems. The initial value of the register is set by BIOS and
is read by driver during the audio component init sequence.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920083918.27057-1-kai.vehmanen@linux.intel.com
Added docbook info regarding Display State Buffer(DSB) which
is added from gen12 onwards to batch submit display HW programming.
v1: Initial version as RFC.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-11-animesh.manna@intel.com
Gamma lut programming can be programmed using DSB
where bulk register programming can be done using indexed
register write which takes number of data and the mmio offset
to be written.
Currently enabled for 12-bit gamma LUT which is enabled by
default and later 8-bit/10-bit will be enabled in future
based on need.
v1: Initial version.
v2: Directly call dsb-api at callsites. (Jani)
v3:
- modified the code as per single dsb instance per crtc. (Shashank)
- Added dsb get/put call in platform specific load_lut hook. (Jani)
- removed dsb pointer from dev_priv. (Jani)
v4: simplified code by dropping ref-count implementation. (Shashank)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-9-animesh.manna@intel.com
Batch buffer will be created through dsb-reg-write function which can have
single/multiple request based on usecase and once the buffer is ready
commit function will trigger the execution of the batch buffer. All
the registers will be updated simultaneously.
v1: Initial version.
v2: Optimized code few places. (Chris)
v3: USed DRM_ERROR for dsb head/tail programming failure. (Shashank)
v4: reset ins_start_offset after commit. (Jani)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-8-animesh.manna@intel.com
DSB will be used for performance improvement for some special scenario.
DSB engine will be enabled based on need and after completion of its work
will be disabled. Api added for enable/disable operation by using DSB_CTRL
register.
v1: Initial version.
v2: POSTING_READ added after writing control register. (Shashank)
v3: cosmetic changes done. (Shashank)
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-7-animesh.manna@intel.com
As per bspec check for DSB status before programming any
of its register. Inline function added to check the dsb status.
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-6-animesh.manna@intel.com
DSB can program large set of data through indexed register write
(opcode 0x9) in one shot. DSB feature can be used for bulk register
programming e.g. gamma lut programming, HDR meta data programming.
v1: initial version.
v2: simplified code by using ALIGN(). (Chris)
v3: ascii table added as code comment. (Shashank)
v4: cosmetic changes done. (Shashank)
v5: reset ins_start_offset. (Jani)
v6: update ins_start_offset in inel_dsb_reg_write.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-5-animesh.manna@intel.com
DSB support single register write through opcode 0x1. Generic
api created which accumulate all single register write in a batch
buffer and once DSB is triggered, it will program all the registers
at the same time.
v1: Initial version.
v2: Unused macro removed and cosmetic changes done. (Shashank)
v3: set free_pos to zero in dsb-put() instead dsb-get() and
a cosmetic change. (Shashank)
v4: macro of indexed-write is moved. (Shashank)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-4-animesh.manna@intel.com
This patch adds a function, which will internally get the gem buffer
for DSB engine. The GEM buffer is from global GTT, and is mapped into
CPU domain, contains the data + opcode to be feed to DSB engine.
v1: Initial version.
v2:
- removed some unwanted code. (Chris)
- Used i915_gem_object_create_internal instead of _shmem. (Chris)
- cmd_buf_tail removed and can be derived through vma object. (Chris)
v3: vma realeased if i915_gem_object_pin_map() failed. (Shashank)
v4: for simplification and based on current usage added single dsb
object in intel_crtc. (Shashank)
v5: seting NULL to cmd_buf moved outside of mutex in dsb-put(). (Shashank)
v6:
- refcount machanism added.
- Used atomic_add_return and atomic_dec_and_test instead of
atomic_inc and atomic_dec. (Jani)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[Jani: added #include <linux/types.h> while pushing]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-3-animesh.manna@intel.com
For icl+, have hw read out to create hw blob of gamma
lut values. icl+ platforms supports multi segmented gamma
mode by default, add hw lut creation for this mode.
This will be used to validate gamma programming using dsb
(display state buffer) which is a tgl specific feature.
Major change done-removal of readouts of coarse and fine segments
because PAL_PREC_DATA register isn't giving propoer values.
State checker limited only to "fine segment"
v2: -readout code for multisegmented gamma has to come
up with some intermediate entries that aren't preserved
in hardware (Jani N)
-linear interpolation (Ville)
-moved common code to check gamma_enable to specific funcs,
since icl doesn't support that
v3: -use u16 instead of __u16 [Jani N]
-used single lut [Jani N]
-improved and more readable for loops [Jani N]
-read values directly to actual locations and then fill gaps [Jani N]
-moved cleaning to patch 1 [Jani N]
-renamed icl_read_lut_multi_seg() to icl_read_lut_multi_segment to
make it similar to icl_load_luts()
-renamed icl_compute_interpolated_gamma_blob() to
icl_compute_interpolated_gamma_lut_values() more sensible, I guess
v4: -removed interpolated func for creating gamma lut values
-removed readouts of fine and coarse segments, failure to read PAL_PREC_DATA
correctly
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1569096654-24433-3-git-send-email-swati2.sharma@intel.com
On ILK-IVB the pipe colorspace is configured via PIPECONF
(as opposed to PIPEMISC in BDW+). Let's configure+readout
that stuff correctly.
Enabling YCbCr 4:4:4 output will now be a simple matter of
setting crtc_state->output_format appropriately in the encoder
.compute_config(). However, when we do that we must be
aware of the fact that YCbCr DP output doesn't seem to work
on ILK (resulting image is totally garbled), but on SNB+
it works fine. However HDMI YCbCr output does work correctly
even on ILK.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-13-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Prepare the pipe csc for YCbCr output on ilk/snb. The main difference
to IVB+ is the lack of explicit post offsets, and instead we must
configure the CSC info RGB->YUV mode (which takes care of offsetting
Cb/Cr properly) and enable the "black screen offset" bit to add the
required offset to Y.
And while at it throw some comments around the bit defines to
document which platforms have which bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-12-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
On HSW the pipe colorspace is configured via PIPECONF
(as opposed to PIPEMISC in BDW+). Let's configure+readout
that stuff correctly.
Enabling YCbCr 4:4:4 output will now be a simple matter of
setting crtc_state->output_format appropriately in the encoder
.compute_config().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-10-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Make intel_get_crtc_ycbcr_config() simpler and rename it
to bdw_get_pipemisc_output_format() to better reflect what
it does.
Also toss in some comments to document that the 4:2:0 PIPECONF
bits are glk+ only. They are mbz on earlier platforms so reading
them unconditionally is safe however.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-9-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Since HSW the PIPECONF progressive vs. interlaced selection is done
with just two bits instead of the earlier three. Let's not look at the
extra bit on HSW+. Also gen2 doesn't support interlaced displays at all.
This is actually fine as is currently because the extra bit is mbz (as
are all three bits on gen2). But just to avoid mishaps in the future
if the bits get reused let's only look at what's properly defined.
v2: constify crtc_state
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-8-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
crtc_state->limited_color_range only applies to RGB output but
we're currently setting it even for YCbCr output. That will
lead to conflicting MSA and PIPECONF settings which can mess
up the image. Let's make sure limited_color_range stays unset
with YCbCr output.
Also WARN if we end up with such a bogus combination when
programming the MSA MISC bits as it's impossible to even
indicate quantization rangle for YCbCr via MSA MISC. YCbCr
output is simply assumed to be limited range always. Note
that VSC SDP does provide a mechanism for full range YCbCr,
so in the future we may want to rethink how we compute/store
this state.
And for good measure we add the same WARN to the HDMI path.
v2: s/==/!=/ in the HDMI WARN
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718164523.11738-1-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
We're configuring the AVI infoframe quantization range bits as if
we're always transmitting RGB pixels. Let's fix this so that we
correctly indicate limited range YCC quantization range when
transmitting YCbCr instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-4-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Looks like we're currently setting the MSA to xvYCC BT.709 instead
of the YCbCr BT.601 claimed by the comment. But even that comment
is wrong since we configure the CSC matrix to BT.709.
Let's remove the bogus statement from the comment and fix the
MSA to indicate YCbCr BT.709 so that it matches the actual
pixel data we're transmitting.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-3-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
As between HDMI and DP have different colorspaces, in order to distinguish
colorspace of DP and HDMI, it renames drm_mode_create_colorspace_property()
function to drm_mode_create_hdmi_colorspace_property() function for HDMI
connector.
In order to apply changed drm api, i915 driver has channged.
It addresses review comments from Ville.
- Split hunk into renaming and adding of code.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919195311.13972-4-gwan-gyeong.mun@intel.com
The request->timeline is only valid until the request is retired (i.e.
before it is completed). Upon retiring the request, the context may be
unpinned and freed, and along with it the timeline may be freed. We
therefore need to be very careful when chasing rq->timeline that the
pointer does not disappear beneath us. The vast majority of users are in
a protected context, either during request construction or retirement,
where the timeline->mutex is held and the timeline cannot disappear. It
is those few off the beaten path (where we access a second timeline) that
need extra scrutiny -- to be added in the next patch after first adding
the warnings about dangerous access.
One complication, where we cannot use the timeline->mutex itself, is
during request submission onto hardware (under spinlocks). Here, we want
to check on the timeline to finalize the breadcrumb, and so we need to
impose a second rule to ensure that the request->timeline is indeed
valid. As we are submitting the request, it's context and timeline must
be pinned, as it will be used by the hardware. Since it is pinned, we
know the request->timeline must still be valid, and we cannot submit the
idle barrier until after we release the engine->active.lock, ergo while
submitting and holding that spinlock, a second thread cannot release the
timeline.
v2: Don't be lazy inside selftests; hold the timeline->mutex for as long
as we need it, and tidy up acquiring the timeline with a bit of
refactoring (i915_active_add_request)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919111912.21631-1-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----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=5CRH
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-09-18' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main pull request for 5.4-rc1 merge window. I don't think
there is anything outstanding so next week should just be fixes, but
we'll see if I missed anything. I landed some fixes earlier in the
week but got delayed writing summary and sending it out, due to a mix
of sick kid and jetlag!
There are some fixes pending, but I'd rather get the main merge out of
the way instead of delaying it longer.
It's also pretty large in commit count and new amd header file size.
The largest thing is four new amdgpu products (navi12/14, arcturus and
renoir APU support).
Otherwise it's pretty much lots of work across the board, i915 has
started landing tigerlake support, lots of icelake fixes and lots of
locking reworking for future gpu support, lots of header file rework
(drmP.h is nearly gone), some old legacy hacks (DRM_WAIT_ON) have been
put into the places they are needed.
uapi:
- content protection type property for HDCP
core:
- rework include dependencies
- lots of drmP.h removals
- link rate calculation robustness fix
- make fb helper map only when required
- add connector->DDC adapter link
- DRM_WAIT_ON removed
- drop DRM_AUTH usage from drivers
dma-buf:
- reservation object fence helper
dma-fence:
- shrink dma_fence struct
- merge signal functions
- store timestamps in dma_fence
- selftests
ttm:
- embed drm_get_object struct into ttm_buffer_object
- release_notify callback
bridges:
- sii902x - audio graph card support
- tc358767 - aux data handling rework
- ti-snd64dsi86 - debugfs support, DSI mode flags support
panels:
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191, Boe
Himax8279d, Sharp LD-D5116Z01B
- TI nspire, NEC NL8048HL11, LG Philips LB035Q02, Sharp LS037V7DW01,
Sony ACX565AKM, Toppoly TD028TTEC1 Toppoly TD043MTEA1
i915:
- Initial tigerlake platform support
- Locking simplification work, general all over refactoring.
- Selftests
- HDCP debug info improvements
- DSI properties
- Icelake display PLL fixes, colorspace fixes, bandwidth fixes, DSI
suspend/resume
- GuC fixes
- Perf fixes
- ElkhartLake enablement
- DP MST fixes
- GVT - command parser enhancements
amdgpu:
- add wipe memory on release flag for buffer creation
- Navi12/14 support (may be marked experimental)
- Arcturus support
- Renoir APU support
- mclk DPM for Navi
- DC display fixes
- Raven scatter/gather support
- RAS support for GFX
- Navi12 + Arcturus power features
- GPU reset for Picasso
- smu11 i2c controller support
amdkfd:
- navi12/14 support
- Arcturus support
radeon:
- kexec fix
nouveau:
- improved display color management
- detect lack of GPU power cables
vmwgfx:
- evicition priority support
- remove unused security feature
msm:
- msm8998 display support
- better async commit support for cursor updates
etnaviv:
- per-process address space support
- performance counter fixes
- softpin support
mcde:
- DCS transfers fix
exynos:
- drmP.h cleanup
lima:
- reduce logging
kirin:
- misc clenaups
komeda:
- dual-link support
- DT memory regions
hisilicon:
- misc fixes
imx:
- IPUv3 image converter fixes
- 32-bit RGB V4L2 pixel format support
ingenic:
- more support for panel related cases
mgag200:
- cursor support fix
panfrost:
- export GPU features register to userspace
- gpu heap allocations
- per-fd address space support
pl111:
- CLD pads wiring support removed from DT
rockchip:
- rework to use DRM PSR helpers
- fix bug in VOP_WIN_GET macro
- DSI DT binding rework
sun4i:
- improve support for color encoding and range
- DDC enabled GPIO
tinydrm:
- rework SPI support
- improve MIPI-DBI support
- moved to drm/tiny
vkms:
- rework CRC tracking
dw-hdmi:
- get_eld and i2s improvements
gm12u320:
- misc fixes
meson:
- global code cleanup
- vpu feature detect
omap:
- alpha/pixel blend mode properties
rcar-du:
- misc fixes"
* tag 'drm-next-2019-09-18' of git://anongit.freedesktop.org/drm/drm: (2112 commits)
drm/nouveau/bar/gm20b: Avoid BAR1 teardown during init
drm/nouveau: Fix ordering between TTM and GEM release
drm/nouveau/prime: Extend DMA reservation object lock
drm/nouveau: Fix fallout from reservation object rework
drm/nouveau/kms/nv50-: Don't create MSTMs for eDP connectors
drm/i915: Use NOEVICT for first pass on attemping to pin a GGTT mmap
drm/i915: to make vgpu ppgtt notificaiton as atomic operation
drm/i915: Flush the existing fence before GGTT read/write
drm/i915: Hold irq-off for the entire fake lock period
drm/i915/gvt: update RING_START reg of vGPU when the context is submitted to i915
drm/i915/gvt: update vgpu workload head pointer correctly
drm/mcde: Fix DSI transfers
drm/msm: Use the correct dma_sync calls harder
drm/msm: remove unlikely() from WARN_ON() conditions
drm/msm/dsi: Fix return value check for clk_get_parent
drm/msm: add atomic traces
drm/msm/dpu: async commit support
drm/msm: async commit support
drm/msm: split power control from prepare/complete_commit
drm/msm: add kms->flush_commit()
...
Modern platforms allow the transcoders hdisplay/vdisplay to exceed the
planes' max resolution. This has the nasty implication that modes on the
connectors' mode list may not be usable when the user asks for a
fullscreen plane. Seeing as that is the most common use case it seems
prudent to filter out modes that don't allow for fullscreen planes to
be enabled.
Let's do that in the connetor .mode_valid() hook so that normally
such modes are kept hidden but the user is still able to forcibly
specify such a mode if they know they don't need fullscreen planes.
This is in line with ealier policies regarding certain clock limits.
The idea is to prevent the casual user from encountering a mode that
would fail under typical conditions, but allow the expert user to
force things if they so wish.
Maybe in the future we should consider automagically using two
planes when one can't cover the entire screen? Wouldn't be a
great match for the current uapi with explicit planes though,
but I guess no worse than using two pipes (which we apparently
have to in the future anyway). Either that or we'd have to
teach userspace to do it for us.
v2: Fix icl+ max plane heigth (Manasi)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Leho Kraav <leho@kraav.com>
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190918150707.32420-1-ville.syrjala@linux.intel.com
The officially validated plane width limit is 4k on skl+, however
we already had people using 5k displays before we started to enforce
the limit. Also it seems Windows allows 5k resolutions as well
(though not sure if they do it with one plane or two).
According to hw folks 5k should work with the possible
exception of the following features:
- Ytile (already limited to 4k)
- FP16 (already limited to 4k)
- render compression (already limited to 4k)
- KVMR sprite and cursor (don't care)
- horizontal panning (need to verify this)
- pipe and plane scaling (need to verify this)
So apart from last two items on that list we are already
fine. We should really verify what happens with those last
two items but I don't have a 5k display on hand atm so it'll
have to wait.
In the meantime let's just bump the limit back up to 5k since
several users have already been using it without apparent issues.
At least we'll be no worse off than we were prior to lowering
the limits.
Cc: stable@vger.kernel.org
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Leho Kraav <leho@kraav.com>
Fixes: 372b9ffb57 ("drm/i915: Fix skl+ max plane width")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111501
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190905135044.2001-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
We generally assume future platforms will inherit the behavior of the
most recent platforms, so update our DDC pin mapping defaults to match
how ICP/TGP behave (i.e., pins starting from GMBUS_PIN_1_BXT for combo
PHY's and pins starting from GMBUS_PIN_9_TC1_ICP for TC PHY's). MCC's
non-standard handling of combo PHY C seems like a platform-specific
quirk that is unlikely to be duplicated on future platforms, so continue
handling it as a special case.
Without this change, future platforms would default to gen4-style pin
mapping which is almost certainly not what we'll want.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190918235626.3750-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Stop setting ->pipe_mask to zero when display is disabled, allowing us
to have different code paths for not actually having display hardware,
and having display hardware disabled. This lets us develop those two
avenues independently.
There are no functional changes for when there is no display. However,
all uses of for_each_pipe() and for_each_pipe_masked() will start
running for the disabled display case. Put one of the more significant
ones behind checks for INTEL_DISPLAY_ENABLED(), otherwise the cases
should not be hit with disabled display, or they seem benign. Fingers
crossed.
All in all, this might not be the ideal solution. In fact we may have
had something along the lines of this in the past, but we ended up
conflating the two cases. Possibly even by recommendation by yours
truly; I did not dare dig up that part of the history. But the perfect
is the enemy of the good, this is a straightforward change, and lets us
get actual work done in both fronts without interfering with each other.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190916092901.31440-1-jani.nikula@intel.com
There's a helper in drm_fourcc.h these days to check of we're dealing
with a two plane YUV format. Make use if it.
Also s/plane/color_plane/ in skl_plane_relative_data_rate() to reduce
the confusion.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190913193157.9556-2-ville.syrjala@linux.intel.com
Prepare for making a distinction between not having display and having
disabled display. Add INTEL_DISPLAY_ENABLED() and use it where
HAS_DISPLAY() is used after intel_device_info_runtime_init(). This is
initially duplication, as disabling display still leads to ->pipe_mask =
0 and HAS_DISPLAY() being false.
Note that ever since i915.display_disable was introduced, it has not
affected PCH detection even if it uses HAS_DISPLAY(), as display disable
happens after that.
Since INTEL_DISPLAY_ENABLED() will not make sense unless HAS_DISPLAY()
is true, include a warning for catching misuses making decisions on
INTEL_DISPLAY_ENABLED() when HAS_DISPLAY() is false.
v2: Remove INTEL_DISPLAY_ENABLED() check from intel_detect_pch() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190913100407.30991-1-jani.nikula@intel.com
On ICL+, the max supported plane height is 4320, so bump it up
To support 4320, we need to increase the number of bits used to
read plane_height to 13 as opposed to older 12 bits.
v4:
* Adjust the width mask also since extra bits are mbz (Ville)
v3:
* Use 0xffff for mask as extra bits are mbz (Ville)
v2:
* ICL plane height supported is 4320 (Ville)
* Add a new line between max width and max height (Jose)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712203808.4126-1-manasi.d.navare@intel.com
On ICL+, the vertical limits for the transcoders are increased to 8192
and horizontal limits are bumped to 16K so bump up
limits in intel_mode_valid()
v4:
* Increase the hdisplay to 16K (Ville)
v3:
* Supported starting ICL (Ville)
* Use the higher limits from TRANS_VTOTAL register (Ville)
v2:
* Checkpatch warning (Manasi)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712202214.3906-1-manasi.d.navare@intel.com
The FBC requires a couple of contiguous buffers, which we allocate from
stolen memory. If stolen memory is unavailable, we cannot allocate those
buffers and so cannot support FBC. Mark it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911175926.31365-1-chris@chris-wilson.co.uk
Reuse the same .modeset_calc_cdclk() function for all bxt+.
The only difference in between the cnl/icl and the bxt variants
is the call to cnl_compute_min_voltage_level(). We can do that call
just fine on older platforms since they leave min_voltage_level[]
zeroed. Let's rename the function to bxt_compute_min_voltage_level()
just so it stays consistent with the rest of the naming scheme.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911133129.27466-4-ville.syrjala@linux.intel.com
We're forgetting to mask off all three pipe select bits from the
CDCLK_CTL value on icl+ which may lead to the extra bit being
left in. That will cause us to consider the current hardware
cdclk state as invalid, and we proceed to sanitize it even
though the hardware may have active pipes and whatnot.
Fix up the mask so we get rid of all three pipe select bits
and thus hopefully no longer sanitize cdclk when it's already
correctly programmed.
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111641
Fixes: 0c1279b58f ("drm/i915: Consolidate {bxt,cnl,icl}_init_cdclk")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911133129.27466-2-ville.syrjala@linux.intel.com
On tgl/bxt/glk the cdclk bypass frequency depends on the PLL
reference clock. So let's read out the ref clock before we
try to compute the bypass clock.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 71dc367e2b ("drm/i915: Consolidate bxt/cnl/icl cdclk readout")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911133129.27466-1-ville.syrjala@linux.intel.com
Abstract away direct access to ->num_pipes to allow further
refactoring. No functional changes.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911092608.13009-1-jani.nikula@intel.com
system_unbound_wq can't keep up sometimes and we get dropped frames.
Switch to a high priority variant.
Reported-by: Heinrich Fink <heinrich.fink@daqri.com>
Tested-by: Heinrich Fink <heinrich.fink@daqri.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910121347.22958-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 736da8112f ("drm/i915: Use literal representation of cdclk
tables") pushed the cdclk logic into tables, adding glk_cdclk_table but
not using yet:
drivers/gpu/drm/i915/display/intel_cdclk.c:1173:38: error: ‘glk_cdclk_table’ defined but not used [-Werror=unused-const-variable=]
Fixes: 736da8112f ("drm/i915: Use literal representation of cdclk tables")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190911074727.32585-1-chris@chris-wilson.co.uk
The BXT and CNL functions were already basically identical, whereas
ICL's function tried to do its own sanitization rather than calling
bxt_sanitize_cdclk.
This should actually fix a bug in our ICL initialization where it would
consider the /2 CD2X divider invalid and force an unnecessary
sanitization (we now have valid clock frequencies that use this
divider).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-9-matthew.d.roper@intel.com
When reading out the BIOS-programmed cdclk state, let's make sure that
the cdclk value is on the valid list for the platform, ensure that the
VCO matches the cdclk, and ensure that the CD2X divider was set
properly.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-8-matthew.d.roper@intel.com
With all of the cdclk function consolidation, we can cut down on a lot
of platform if/else logic by creating a vfunc that's initialized at
startup.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-7-matthew.d.roper@intel.com
The uninitialize flow is the same on all of these platforms, aside from
calculating a different frequency level.
v2: Reverse platform conditional order for consistency. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-6-matthew.d.roper@intel.com
The CNL variant of this function is identical to the BXT variant aside
from not needing to handle SSA precharge.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-5-matthew.d.roper@intel.com
We'd previously combined ICL/TGL logic into the cnl_set_cdclk function,
but BXT is pretty similar as well. Roll the cnl/icl/tgl logic back into
the bxt function; the only things we really need to handle separately
are punit notification and calling different functions to enable/disable
the cdclk PLL.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910154252.30503-4-matthew.d.roper@intel.com
The bspec lays out legal cdclk frequencies, PLL ratios, and CD2X
dividers in an easy-to-read table for most recent platforms. We've been
translating the data from that table into platform-specific code logic,
but it's easy to overlook an area we need to update when adding new
cdclk values or enabling new platforms. Let's just add a form of the
bspec table to the code and then adjust our functions to pull what they
need directly out of the table.
v2: Fix comparison when finding best cdclk.
v3: Another logic fix for calc_cdclk.
v4:
- Use named initializers for cdclk tables. (Ville)
- Include refclk as a field in the table instead of adding all three
ratios for each entry. (Ville)
- Terminate tables with an empty entry to avoid needing to store the
table size. (Ville)
- Don't try so hard to return reasonable values from our lookup
functions if we get impossible inputs; just WARN and return 0.
(Ville)
- Keep a bxt_ prefix on the lookup functions since they're still only
used on bxt+ for now. We can rename them later if we extend this
table-based approach back to older platforms. (Ville)
v5:
- Fix cnl table's ratios for 24mhz refclk. (Ville)
- Don't miss the named initializers on the cnl table. (Ville)
- Represent refclk in table as u16 rather than u32. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910161506.7158-1-matthew.d.roper@intel.com
Aside from a few minor register changes and some different clock values,
cdclk design hasn't changed much since gen9lp. Let's consolidate the
handlers for bxt, cnl, and icl to keep the codeflow consistent.
Also, while we're at it, s/bxt_de_pll_update/bxt_de_pll_readout/ since
"update" makes me think we should be writing to hardware rather than
reading from it.
v2:
- Fix icl_calc_voltage_level() limits. (Ville)
- Use CNL_CDCLK_PLL_RATIO_MASK rather than BXT_DE_PLL_RATIO_MASK on
gen10+ to avoid confusion. (Ville)
v3:
- Also fix ehl_calc_voltage_level() limits. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190910160520.6587-1-matthew.d.roper@intel.com
For cherryview, add hw read out to create hw blob of gamma
lut values.
Review comments from previous series:
https://patchwork.freedesktop.org/patch/328252
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed function cherryview_get_color_config() to chv_read_luts()
-Renamed cherryview_get_gamma_config() to chv_read_cgm_gamma_lut()
[Ville]
v9: -80 character limit [Uma]
-Made read func para as const [Ville, Uma]
-Renamed chv_read_cgm_gamma_lut() to chv_read_cgm_gamma_lut()
[Ville, Uma]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1568030503-26747-4-git-send-email-swati2.sharma@intel.com
For i965, add hw read out to create hw blob of gamma
lut values.
Review comments from old series:
https://patchwork.freedesktop.org/series/58039/
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally
within the function [Ville]
-Renamed i965_get_color_config() to i965_read_lut() [Ville]
-Renamed i965_get_gamma_config_10p6() to i965_read_gamma_lut_10p6()
[Ville]
v9: -Typo and 80 character limit [Uma]
-Made read func para as const [Ville, Uma]
-Renamed i965_read_gamma_lut_10p6() to i965_read_lut_10p6() [Ville, Uma]
v10: -Swapped ldw and udw while creating hw blob [Jani]
-Added last index rgb lut value from PIPEGCMAX to h/w blob [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1568030503-26747-3-git-send-email-swati2.sharma@intel.com
intel_color_get_gamma_bit_precision() is extended for
cherryview by adding chv_gamma_precision(), i965 will use existing
i9xx_gamma_precision() func only.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1568030503-26747-2-git-send-email-swati2.sharma@intel.com
My attempt at allowing MST to use the higher color depths has
regressed some configurations. Apparently people have setups
where all MST streams will fit into the DP link with 8bpc but
won't fit with higher color depths.
What we really should be doing is reducing the bpc for all the
streams on the same link until they start to fit. But that requires
a bit more work, so in the meantime let's revert back closer to
the old behavior and limit MST to at most 8bpc.
Cc: stable@vger.kernel.org
Cc: Lyude Paul <lyude@redhat.com>
Tested-by: Geoffrey Bennett <gmux22@gmail.com>
Fixes: f147721986 ("drm/i915: Remove the 8bpc shackles from DP MST")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111505
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828102059.2512-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 75427b2a2b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unlike gen11, which always ran at 50MHz when the cdclk PLL was disabled,
TGL runs at refclk/2. The 50MHz croclk/2 is only used by hardware
during some power state transitions.
Bspec: 49201
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190905181337.23727-1-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tiger Lake has up to 4 pipes so the mask would need to be 0xf instead of
0x7. Do not hardcode the mask so it allows the fake MST encoders to
connect to all pipes no matter how many the platform has.
Iterating over all pipes to keep consistent with intel_ddi_init().
Initialy this patch was replaced by commit 4eaceea3a0 ("drm/i915:
Fix DP-MST crtc_mask") but userspace it not correctly using
encoder.possible_crtcs and it was reverted by
commit e838bfa8e1 ("Revert "drm/i915: Fix DP-MST crtc_mask"")
Userspace should be fixed but it might take a while, so bringing this
patch back for now.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904230241.20638-2-jose.souza@intel.com
WA 1409120013 is also valid for TGL, so lets check for ">= 11".
BSpec: 52890
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904230241.20638-1-jose.souza@intel.com
Gen 12 onwards moves the DP_TP_* registers to be transcoder-based rather
than port-based. This adds the new register addresses and changes all
the callers to use the register saved in intel_dp->regs.*. This is
filled out when preparing to enable the port so we take into account if
we should use the transcoder or the port.
v2: reimplement by stashing the registers we want to access under
intel_dp->reg. Now they are initialized when enabling the port.
Ville suggested to store the transcoder to be used exclusively
by TGL+. After implementing I thought just storing the register directly
made it cleaner.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-5-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
DP_TP_{CTL,STATUS} should only be programmed when the encoder is intel_dp.
Checking its current usages intel_disable_ddi_buf() is the only
offender, with other places being protected by checks like
pipe_config->fec_enable that is only set by intel_dp.
v3 (José):
- Using intel_crtc_has_dp_encoder() instead of intel_encoder_is_dp()
(Ville)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-4-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
For older gens PSR IIR and IMR have fixed addresses. From TGL onwards those
registers moved to each transcoder offset. The bits for the registers
are defined without an offset per transcoder as right now we have one
register per transcoder. So add a fake "trans_shift" when calculating
the bits offsets: it will be 0 for gen12+ and psr.transcoder otherwise.
v2 (Lucas): change the implementation to use trans_shift instead of
getting each bit value with a different macro
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-3-jose.souza@intel.com
It was enabling and checking PSR interruptions in every transcoder
while it should keep the interruptions on the non-used transcoders
masked.
While doing this it gives us trouble on Tiger Lake if we are
reading/writing to registers of disabled transcoders since from gen12
onwards the registers are relative to the transcoder. Instead of forcing
them ON to access those registers, just avoid the accesses as they are
not needed.
v2 (Lucas):
- Explain why we can't keep accessing all transcoders
- Remove TODO about extending the irq handling to multiple instances:
when/if implementing multiple instances it's pretty clear by the
singleton psr that it needs to be extended
- Fix intel_psr_debug_set() calling psr_irq_control() with
psr.transcoder not set yet (from Imre). Now we only set the debug
register right away if psr is already enabled. Otherwise we just
record the value to be set when enabling the source.
- Do not depend on the value of TRANSCODER_A. Just be relative to it
(from Imre)
- handle psr error last so we don't schedule the work before handling
the other flags
v3:
- Adding a warning about setting reserverd bits on EDP_PSR_IMR
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-2-jose.souza@intel.com
This reverts commit 4eaceea3a0.
Several userspace clients (modesetting ddx and mutter+wayland at least)
handle encoder.possible_crtcs incorrectly. What they essentially do is
the following:
possible_crtcs = ~0;
for_each_possible_encoder(connector)
possible_crtcs &= encoder->possible_crtcs;
Ie. they calculate the intersection of the possible_crtcs
for the connector when they really should be calculating the
union instead.
In our case each MST encoder now has just one unique bit set,
and so the intersection is always zero. The end result is that
MST connectors can't be lit up because no crtc can be found to
drive them.
I've submitted a fix for the modesetting ddx [1], and complained
on #wayland about mutter, so hopefully the situation will improve
in the future. In the meantime we have regression, and so must go
back to the old way of misconfiguring possible_crtcs in the kernel.
[1] https://gitlab.freedesktop.org/xorg/xserver/merge_requests/277
Cc: Jonas Ådahl <jadahl@gmail.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111507
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903154018.26357-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
For glk, add hw read out to create hw blob of gamma
lut values.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed glk_get_color_config() to glk_read_luts() [Ville]
-Added degamma validation [Ville]
v9: -80 character limit [Uma]
-Made read func para as const [Ville, Uma]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-8-git-send-email-swati2.sharma@intel.com
For ilk, add hw read out to create hw blob of gamma
lut values.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed ilk_get_color_config() to ilk_read_luts() [Ville]
v9: -80 character limit [Uma]
-Made read func para as const [Ville, Uma]
-Renamed ilk_read_gamma_lut() to ilk_read_lut_10() [Uma, Ville]
v10: -Made ilk_read_luts() static [Jani]
-ilk_load_lut_10 has lut_size, not (lut_size - 1) [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-7-git-send-email-swati2.sharma@intel.com
For the legacy(gen < 4) gamma, add hw read out to create hw blob of gamma
lut values. Also, add function intel_color_lut_pack to convert hw value
with given bit precision to lut property val.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed function i9xx_get_color_config() to i9xx_read_luts()
-Renamed i9xx_get_config_internal() to i9xx_read_lut_8() [Ville]
v9: -Change in commit message [Jani, Uma]
-Wrap commit within 75 characters [Uma]
-Use macro for 256 [Uma]
-Made read func para as const [Ville, Uma]
v10: -Made i9xx_read_luts() static [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-6-git-send-email-swati2.sharma@intel.com
Add macro to compare hw/sw gamma lut values. First need to
check whether hw/sw gamma mode matches or not. If not
no need to compare lut values, if matches then only compare
lut entries.
v5: -Called PIPE_CONF_CHECK_COLOR_LUT inside if (!adjust) [Jani]
-Added #undef PIPE_CONF_CHECK_COLOR_LUT [Jani]
v8: -Added check for gamma mode before gamma lut entry comparison
[Jani]
-Split patch 3 into 4 patches
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-5-git-send-email-swati2.sharma@intel.com
Add func intel_color_lut_equal() to compare hw/sw gamma
lut values. Since hw/sw gamma lut sizes and lut entries comparison
will be different for different gamma modes, add gamma mode dependent
checks.
v3: -Rebase
v4: -Renamed intel_compare_color_lut() to intel_color_lut_equal() [Jani]
-Added the default label above the correct label [Jani]
-Corrected smatch warn "variable dereferenced before check"
[Dan Carpenter]
v5: -Added condition (!blob1 && !blob2) return true [Jani]
v6: -Made patch11 as patch3 [Jani]
v8: -Split patch 3 into 4 patches
-Optimized blob check condition [Ville]
v9: -Exclude spilt gamma mode (bdw and ivb platforms)
as there is exception in way gamma values are written in
hardware [Ville]
-Added exception made in commit [Uma]
-Dropped else, character limit and indentation [Uma]
-Added multi segmented gama mode for icl+ platforms [Uma]
v10: -Dropped multi segmented mode for icl+ platforms [Jani]
-Removed references of sw and hw state in compare code [Jani]
-Dropped inline from func [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-4-git-send-email-swati2.sharma@intel.com
Each platform supports different gamma modes and each gamma mode
has different bit precision. Here bit precision corresponds
to number of bits the hw LUT supports.
Add func per platform to return bit precision corresponding to gamma mode
which will be later used as a parameter in lut comparison function
intel_color_lut_equal().
This is done for legacy, ilk, glk and their variant platforms.
v6: -Added func intel_color_get_bit_precision() to get bit precision for
gamma and degamma lut readout depending upon platform and
corresponding to load_luts() [Ankit]
-Made patch11 as patch3 [Jani]
v7: -Renamed func intel_color_get_bit_precision() to
intel_color_get_gamma_bit_precision()
-Added separate function/platform for gamma bit precision [Ville]
-Corrected checkpatch warnings
v8: -Split patch 3 into 4 separate patches
v9: -Changed commit message, gave more info [Uma]
-Added precision func for icl+ platform
v10: -Removed precision func for chv and icl+ platforms [Jani]
-Added gamma_enable check once [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-2-git-send-email-swati2.sharma@intel.com
Add debug log for color related parameters like gamma_mode, gamma_enable,
csc_enable, etc inside intel_dump_pipe_config().
v6: -Added debug log for color para in intel_dump_pipe_config [Jani]
v7: -Split patch 3 into 4 patches
v8: -Corrected alignment [Uma]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-3-git-send-email-swati2.sharma@intel.com
obj->pin_global was originally used as a means to keep the shrinker off
the active scanout, but we use the vma->pin_count itself for that and
the obj->frontbuffer to delay shrinking active framebuffers. The other
role that obj->pin_global gained was for spotting display objects inside
GEM and working harder to keep those coherent; for which we can again
simply inspect obj->frontbuffer directly.
Coming up next, we will want to manipulate the pin_global counter
outside of the principle locks, so would need to make pin_global atomic.
However, since obj->frontbuffer is already managed atomically, it makes
sense to use that the primary key for display objects instead of having
pin_global.
Ville pointed out the principle difference is that obj->frontbuffer is
set for as long as an intel_framebuffer is attached to an object, but
obj->pin_global was only raised for as long as the object was active. In
practice, this means that we consider the object as being on the scanout
for longer than is strictly required, causing us to be more proactive in
flushing -- though it should be true that we would have flushed
eventually when the back became the front, except that on the flip path
that flush is async but when hit from another ioctl it will be
synchronous.
v2: i915_gem_object_is_framebuffer()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190902040303.14195-5-chris@chris-wilson.co.uk
Reogranize the HDMI deep color state computation to just
loop over possible bpc values. Avoids having to maintain
so many variants of the clock etc.
The current code also looks confused w.r.t. port_clock vs.
bw_constrained. It would happily update port_clock for
deep color but then not actually enable deep color due to
bw_constrained being set. The new logic handles that case
correctly.
v2: Pull stuff into separate funcs (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828183424.7856-1-ville.syrjala@linux.intel.com
enum port is a mess now because it no longer matches the spec
at all. Let's start to dig ourselves out of this hole by
reducing our reliance on port_name(). This should at least make
a bunch of debug messages a bit more sensible while we think how
to fill the the hole properly.
Based on the following cocci script with a lot of manual cleanup
(all the format strings etc.):
@@
expression E;
@@
(
- port_name(E->port)
+ E->base.base.id, E->base.name
|
- port_name(E.port)
+ E.base.base.id, E.base.name
)
@@
enum port P;
expression E;
@@
P = E->port
<...
- port_name(P)
+ E->base.base.id, E->base.name
...>
@@
enum port P;
expression E;
@@
P = E.port
<...
- port_name(P)
+ E.base.base.id, E.base.name
...>
@@
expression E;
@@
{
- enum port P = E;
... when != P
}
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830182719.32608-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
My attempt at allowing MST to use the higher color depths has
regressed some configurations. Apparently people have setups
where all MST streams will fit into the DP link with 8bpc but
won't fit with higher color depths.
What we really should be doing is reducing the bpc for all the
streams on the same link until they start to fit. But that requires
a bit more work, so in the meantime let's revert back closer to
the old behavior and limit MST to at most 8bpc.
Cc: stable@vger.kernel.org
Cc: Lyude Paul <lyude@redhat.com>
Tested-by: Geoffrey Bennett <gmux22@gmail.com>
Fixes: f147721986 ("drm/i915: Remove the 8bpc shackles from DP MST")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111505
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828102059.2512-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
The bspec was recently updated with these new cdclk values for ICL, EHL,
and TGL.
Bspec: 20598
Bspec: 49201
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826225540.11987-3-matthew.d.roper@intel.com
The bspec has just recently been updated with new cdclk values that
require the use of a /2 CD2X divider rather than a /1 divider. Once we
add the divider selection logic to ICL+ cdclk programming, we have
pretty much the same logic we were already using on CNL, so it's simpler
to drop icl_set_cdclk() completely and reuse cnl_set_cdclk() on gen11+
platforms as well.
v2:
- Using ICL_CDCLK_CD2X_PIPE_NONE + BXT_CDCLK_CD2X_PIPE(pipe) for TGL is
correct, but looks really confusing. Add some TGL_ macros that alias
these to avoid confusion. (Ville)
- Use DIV_ROUND_CLOSEST rather than / when applying the divider. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830004828.19359-1-matthew.d.roper@intel.com
When we moved the code to disable crtc's to a separate patch,
we forgot to ensure that for_each_oldnew_intel_crtc_in_state_reverse()
was moved as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 66d9cec8a6 ("drm/i915/display: Move the commit_tail() disable sequence to separate function")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830101644.8740-1-maarten.lankhorst@linux.intel.com
>From Gen12 onwards, HDCP HW block is implemented within transcoders.
Till Gen11 HDCP HW block was part of DDI.
Hence required changes in HW programming is handled here.
As ME FW needs the transcoder detail on which HDCP is enabled
on Gen12+ platform, we are populating the detail in hdcp_port_data.
v2:
_MMIO_TRANS is used [Lucas and Daniel]
platform check is moved into the caller [Lucas]
v3:
platform check is moved into a macro [Shashank]
v4:
Few optimizations in the coding [Shashank]
v5:
Fixed alignment in macro definition in i915_reg.h [Shashank]
unused variables "reg" is removed.
v6:
Configuring the transcoder at compute_config.
transcoder is used instead of pipe in macros.
Rebased.
v7:
transcoder is cached at intel_hdcp
hdcp_port_data is configured with transcoder index asper ME FW.
v8:
s/trans/cpu_transcoder
s/tc/cpu_transcoder
v9:
rep_ctl is prepared for TCD too.
return moved into deault of rep_ctl prepare function [Shashank]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-7-ramalingam.c@intel.com
On gen12+ platforms, HDCP HW is associated to the transcoder.
Hence on every modeset update associated transcoder into the
intel_hdcp of the port.
v2:
s/trans/cpu_transcoder [Jani]
v3:
comment is added for fw_ddi init for gen12+ [Shashank]
only hdcp capable transcoder is translated into fw_tc [Shashank]
v4:
fw_tc initialization is kept for modeset. [Tomas]
few extra doc is added at port_data init [Tomas]
v5:
Few comments are improvised [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-6-ramalingam.c@intel.com
We dont need the definition of the enum port outside I915, anymore.
Hence move enum port definition into I915 driver itself.
v2:
intel_display.h is included in intel_hdcp.h
v3:
enum port is declared in headers.
v4:
commit msg is rephrased.
v5:
copyright year is updated [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-3-ramalingam.c@intel.com
I915 converts it's port value into ddi index defiend by ME FW
and pass it as a member of hdcp_port_data structure.
Hence expose the enum mei_fw_ddi to I915 through
i915_mei_interface.h.
v2:
Copyright years are bumped [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-2-ramalingam.c@intel.com
Create a new function intel_commit_modeset_disables() consistent
with the naming in drm atomic helpers and similar to the enable function.
This helps better organize the disable sequence in atomic_commit_tail()
No functional change
v4:
* Do not create a function pointer, just a function (Maarten)
v3:
* Rebase (Manasi)
v2:
* Create a helper for old_crtc_state disables (Lucas)
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828224701.422-1-manasi.d.navare@intel.com
This patch has no functional changes. This just renames the update_crtcs()
hooks to commit_modeset_enables() to match the drm_atomic helper naming
conventions.
v2:
* Rebase on drm-tip
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827221735.29351-2-manasi.d.navare@intel.com
According to BSpc if link standby is set on TGL+, PSR will not be
enabled. Vendors should not use panels that requires link standby and
even if they do, panel should assert a PSR error that will cause PSR to
be disabled.
BSpec: 50434
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-8-lucas.demarchi@intel.com
Yf tiling was removed in gen-12, so do not expose Yf modifiers to user
space. Gen-12 display also is incompatible with pre-gen12 Y-tiled
CCS, so do not expose I915_FORMAT_MOD_Y_TILED_CCS.
v2: Rebase to carry forward recently added gen11 formats.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827084516.6748-1-dhinakaran.pandiyan@intel.com
DSC was not supported on Pipe A for previous platforms. Tigerlake onwards,
all the pipes support DSC. Hence, the DSC and FEC restriction on
Pipe A needs to be removed.
v2: Changes in the logic around removing the restriction around
Pipe A (Manasi, Lucas)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Madhumitha Tolakanahalli Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823004655.28905-1-madhumitha.tolakanahalli.pradeep@intel.com
There is a difference in BSpec's and the driver's designation of DDI
ports. BSpec uses the following names:
- before GEN11:
BSpec/driver:
port A/B/C/D etc
- GEN11:
BSpec/driver:
port A-F
- GEN12:
BSpec:
port A/B/C for combo PHY ports
port TC1-6 for Type C PHY ports
driver:
port A-I.
The driver's port D name matches BSpec's TC1 port name.
So far power domains were named according to the BSpec designation, to
make it easier to match the code against the specification. That however
can be confusing when a power domain needs to be matched to a port on
GEN12+. To resolve that use the driver's port A-I designation for power
domain names too and rename the corresponding power wells so that they
reflect the mapping from the driver's to BSpec's port name.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823100711.27833-1-imre.deak@intel.com
On TGL some registers moved from DDI to transcoder and the
DisplayPort training sequence has a separate BSpec page.
I started adding 'ifs' to the original intel_ddi_pre_enable_dp() but
it was becoming really hard to follow, so a new and cleaner function
for TGL was added with comments of all steps. It's similar to ICL,
but different enough to deserve a new function.
The rest of DisplayPort enable and the whole disable sequences
remained the same.
v2: FEC and DSC should be enabled on sink side before start link
training(Maarten reported and Manasi confirmed the DSC part)
v3: Add call to enable FEC on step 7.l(Manasi)
BSpec: 49190
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-16-lucas.demarchi@intel.com
Disable CRTC/pipes in reverse order because some features (MST in
TGL+) requires master and slave relationship between pipes, so it
should always pick the lowest pipe as master as it will be enabled
first and disable in the reverse order so the master will be the last
one to be disabled.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-13-lucas.demarchi@intel.com
Same as for_each_oldnew_intel_crtc_in_state() but iterates in reverse
order.
v2: Fix additional blank line
v3: Rebase
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-12-lucas.demarchi@intel.com
TGL PSR2 HW supports a bigger resolution, so lets add it
BSpec: 50422, 49199
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-10-lucas.demarchi@intel.com
On TGL+ it's possible to have PSR1 enabled in other ports besides DDIA.
PSR2 is still limited to DDIA. However currently we handle only one
instance of PSR struct. Lets guard intel_psr_init_dpcd() against
multiple eDP panels and warn about it.
v2: Reword commit message to be TGL+ only and with the info where
PSR1/PSR2 are supported (Lucas)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-6-lucas.demarchi@intel.com
Use the new cec_notifier_conn_(un)register() functions to
(un)register the notifier for the HDMI connector, and fill in
the cec_connector_info.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-3-darekm@google.com
Pass the connector info to the CEC adapter. This makes it possible
to associate the CEC adapter with the corresponding drm connector.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814104520.6001-2-darekm@google.com
This patch fixes the intel_configure_pps_for_dsc_encoder() function to use
cpu_transcoder instead of encoder->type to select the correct DSC registers
that was wrongly used in the original patch for one DSC register isntance.
Fixes: 7182414e25 ("drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821215950.24223-1-manasi.d.navare@intel.com
(cherry picked from commit d4c61c4a16)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We're not allowed to create new properties after device registration
so for MST connectors we need to either create the max_bpc property
earlier, or we reuse one we already have. Let's do the latter apporach
since the corresponding SST connector already has the prop and its
min/max are correct also for the MST connector.
The problem was highlighted by commit 4f5368b554 ("drm/kms:
Catch mode_object lifetime errors") which results in the following
spew:
[ 1330.878941] WARNING: CPU: 2 PID: 1554 at drivers/gpu/drm/drm_mode_object.c:45 __drm_mode_object_add+0xa0/0xb0 [drm]
...
[ 1330.879008] Call Trace:
[ 1330.879023] drm_property_create+0xba/0x180 [drm]
[ 1330.879036] drm_property_create_range+0x15/0x30 [drm]
[ 1330.879048] drm_connector_attach_max_bpc_property+0x62/0x80 [drm]
[ 1330.879086] intel_dp_add_mst_connector+0x11f/0x140 [i915]
[ 1330.879094] drm_dp_add_port.isra.20+0x20b/0x440 [drm_kms_helper]
...
Cc: stable@vger.kernel.org
Cc: Lyude Paul <lyude@redhat.com>
Cc: sunpeng.li@amd.com
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Fixes: 5ca0ef8a56 ("drm/i915: Add max_bpc property for DP MST")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820161657.9658-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 1b9bd09630)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We may need to eliminate the crtc->index == pipe assumptions from
the code to support arbitrary pipes being fused off. Start that by
switching some bitmasks over to using pipe instead of the crtc index.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This patch fixes the intel_configure_pps_for_dsc_encoder() function to use
cpu_transcoder instead of encoder->type to select the correct DSC registers
that was wrongly used in the original patch for one DSC register isntance.
Fixes: 7182414e25 ("drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821215950.24223-1-manasi.d.navare@intel.com
DSC engine on ICL supports only 8 and 10 BPC as the input
BPC. But DSC engine in TGL supports 8, 10 and 12 BPC.
Add 12 BPC support for DSC while calculating compression
configuration.
v2: Remove the separate define TGL_DP_DSC_MAX_SUPPORTED_BPC
and use the value directly.(More such defines can be removed
as part of future patches). (Ville)
v3: Use values directly instead of accessing the defines
everytime for min and max DSC BPC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223059.18052-1-anusha.srivatsa@intel.com
No need to unmask PSR interrutpion if PSR is not enabled, better move
the call to intel_psr_enable_source().
v2: Renamed intel_psr_irq_control() to psr_irq_control() (Lucas)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-3-jose.souza@intel.com
According to PSR2_CTL definition in BSpec there is only one instance
of PSR2_CTL. Platforms gen < 12 with EDP transcoder only support PSR2
on TRANSCODER_EDP while on TGL PSR2 is only supported by
TRANSCODER_A.
Since BDW PSR is allowed on any port, but we need to restrict by
transcoder.
v8: Renamed _psr2_supported_in_trans() to psr2_supported() (Lucas)
v9: Renamed psr2_supported() to transcoder_has_psr2() (Ville)
BSpec: 7713
BSpec: 20584
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-2-jose.souza@intel.com
PSR registers are a mess, some have the full address while others just
have the additional offset from psr_mmio_base.
For BDW+ psr_mmio_base is nothing more than TRANSCODER_EDP_OFFSET +
0x800 and using it makes more difficult for people with an PSR
register address or PSR register name from from BSpec as i915 also
don't match the BSpec names.
For HSW psr_mmio_base is _DDI_BUF_CTL_A + 0x800 and PSR registers are
only available in DDIA.
Other reason to make relative to transcoder is that since BDW every
transcoder have PSR registers, so in theory it should be possible to
have PSR enabled in a non-eDP transcoder.
So for BDW+ we can use _TRANS2() to get the register offset of any
PSR register in any transcoder while for HSW we have _HSW_PSR_ADJ
that will calculate the register offset for the single PSR instance,
noting that we are already guarded about trying to enable PSR in other
port than DDIA on HSW by the 'if (dig_port->base.port != PORT_A)' in
intel_psr_compute_config(), this check should only be valid for HSW
and will be changed in future.
PSR2 registers and PSR_EVENT was added after Haswell so that is why
_PSR_ADJ() is not used in some macros.
The only registers that can not be relative to transcoder are
PSR_IMR and PSR_IIR that are not relative to anything, so keeping it
hardcoded. That changed for TGL but it will be handled in another
patch.
Also removing BDW_EDP_PSR_BASE from GVT because it is not used as it
is the only PSR register that GVT have.
v5:
- Macros changed to be more explicit about HSW (Dhinakaran)
- Squashed with the patch that added the tran parameter to the
macros (Dhinakaran)
v6:
- Checking for interruption errors after module reload in the
transcoder that will be used (Dhinakaran)
- Using lowercase to the registers offsets
v7:
- Removing IS_HASWELL() from registers macros(Jani)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-1-jose.souza@intel.com
Avoid calling i915_vma_put_fence() by using our alternate paths that
bind a secondary vma avoiding the original fenced vma. For the few
instances where we need to release the fence (i.e. on binding when the
GGTT range becomes invalid), replace the put_fence with a revoke_fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190822061557.18402-1-chris@chris-wilson.co.uk
We need the rename of reservation_object to dma_resv.
The solution on this merge came from linux-next:
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Wed, 14 Aug 2019 12:48:39 +1000
Subject: [PATCH] drm: fix up fallout from "dma-buf: rename reservation_object to dma_resv"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
---
drivers/gpu/drm/i915/gt/intel_engine_pool.c | 8 ++++----
3 files changed, 7 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/i915/gt/intel_engine_pool.c b/drivers/gpu/drm/i915/gt/intel_engine_pool.c
index 03d90b49584a..4cd54c569911 100644
--- a/drivers/gpu/drm/i915/gt/intel_engine_pool.c
+++ b/drivers/gpu/drm/i915/gt/intel_engine_pool.c
@@ -43,12 +43,12 @@ static int pool_active(struct i915_active *ref)
{
struct intel_engine_pool_node *node =
container_of(ref, typeof(*node), active);
- struct reservation_object *resv = node->obj->base.resv;
+ struct dma_resv *resv = node->obj->base.resv;
int err;
- if (reservation_object_trylock(resv)) {
- reservation_object_add_excl_fence(resv, NULL);
- reservation_object_unlock(resv);
+ if (dma_resv_trylock(resv)) {
+ dma_resv_add_excl_fence(resv, NULL);
+ dma_resv_unlock(resv);
}
err = i915_gem_object_pin_pages(node->obj);
which is a simplified version from a previous one which had:
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We're not allowed to create new properties after device registration
so for MST connectors we need to either create the max_bpc property
earlier, or we reuse one we already have. Let's do the latter apporach
since the corresponding SST connector already has the prop and its
min/max are correct also for the MST connector.
The problem was highlighted by commit 4f5368b554 ("drm/kms:
Catch mode_object lifetime errors") which results in the following
spew:
[ 1330.878941] WARNING: CPU: 2 PID: 1554 at drivers/gpu/drm/drm_mode_object.c:45 __drm_mode_object_add+0xa0/0xb0 [drm]
...
[ 1330.879008] Call Trace:
[ 1330.879023] drm_property_create+0xba/0x180 [drm]
[ 1330.879036] drm_property_create_range+0x15/0x30 [drm]
[ 1330.879048] drm_connector_attach_max_bpc_property+0x62/0x80 [drm]
[ 1330.879086] intel_dp_add_mst_connector+0x11f/0x140 [i915]
[ 1330.879094] drm_dp_add_port.isra.20+0x20b/0x440 [drm_kms_helper]
...
Cc: stable@vger.kernel.org
Cc: Lyude Paul <lyude@redhat.com>
Cc: sunpeng.li@amd.com
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Fixes: 5ca0ef8a56 ("drm/i915: Add max_bpc property for DP MST")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820161657.9658-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
The conversion during HDMI HW readout from port_clock to crtc_clock was
missed when HDMI 10bpc support was added, so fix that.
v2:
- Unscrew the non-HDMI case.
Fixes: cd9e11a8bf ("drm/i915/icl: Add 10-bit support for hdmi")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109593
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808162547.7009-1-imre.deak@intel.com
(cherry picked from commit 2969a78aea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXVqvpwAKCRDj7w1vZxhR
xa3RAQDzAnt5zeesAxX4XhRJzHoCEwj2PJj9Re6xMJ9PlcfcvwD+OS+bcB6jfiXV
Ug9IBd/DqjlmD9G9MxFxfSV946rksAw=
=8uv4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190819141923.7l2adietcr2pioct@flea
Each fake MST encoder is tied to a specific pipe. Fix the encoder's
crtc_mask to reflect that fact.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-16-lucas.demarchi@intel.com
When trying to read registers from transcoder C and D while PG3 is ON it
causes unclaimed access warnings. Adding the powerwells for the pipes
fixes the issue, but doesn't match the spec.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-4-lucas.demarchi@intel.com
The current SKUs added for Tiger Lake don't have DDIC hooked up, even
though it is supported by the SoC. The current state for these SKUs is
problematic since while enabling the combo phy, PORT_COMP_DW* return
0xFFFFFFFF, which is invalid per register definition.
During initialization we check what phys are not yet enabled by reading
PHY_MISC_C and try to enable it by toggling the "DE to IO Comp Pwr Down"
bit. But after that any read to the PORT_COMP_DW* returns invalid
results. This removes the following warning
[56997.634353] Missing case (val == 4294967295)
[56997.639241] WARNING: CPU: 5 PID: 768 at drivers/gpu/drm/i915/display/intel_combo_phy.c:54 cnl_get_procmon_ref_values+0xc9/0xf0 [i915]
[56997.639808] Modules linked in: i915(+) prime_numbers x86_pkg_temp_thermal coretemp kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel e1000e [last unloaded: prime_numbers]
[56997.639808] CPU: 5 PID: 768 Comm: insmod Tainted: G U W 5.2.0-demarchi+ #65
[56997.639808] Hardware name: Intel Corporation Tiger Lake Client Platform/TigerLake U DDR4 SODIMM RVP, BIOS TGLSFWI1.R00.2252.A03.1906270154 06/27/2019
[56997.639808] RIP: 0010:cnl_get_procmon_ref_values+0xc9/0xf0 [i915]
[56997.639808] Code: 2c a0 85 c9 74 e0 81 f9 00 00 00 01 75 09 48 c7 c0 0c a4 2c a0 eb cf 48 c7 c6 3c 3a 31 a0 48 c7 c7 40 3a 31 a0 e8 6b 4d ea e0 <0f> 0b 48 c7 c0 00 a4 2c a0 eb b1 48 c7 c0 24 a4 2
c a0 eb a8 e8 be
[56997.639808] RSP: 0018:ffffc9000068f8a8 EFLAGS: 00010286
[56997.639808] RAX: 0000000000000000 RBX: ffff88848fa90000 RCX: 0000000000000000
[56997.639808] RDX: ffff8884a08b5ef8 RSI: ffff8884a08a6658 RDI: 00000000ffffffff
[56997.639808] RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
[56997.639808] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88848fa90000
[56997.639808] R13: 0000000000000000 R14: 0000000000000002 R15: 0006c00000162000
[56997.639808] FS: 00007f61ca3d12c0(0000) GS:ffff8884a0880000(0000) knlGS:0000000000000000
[56997.639808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[56997.639808] CR2: 00007f71be6a92c0 CR3: 0000000494750006 CR4: 0000000000760ee0
[56997.639808] PKRU: 55555554
[56997.639808] Call Trace:
[56997.639808] cnl_verify_procmon_ref_values+0x36/0xf0 [i915]
[56997.639808] ? rcu_read_lock_sched_held+0x6f/0x80
[56997.639808] ? gen11_fwtable_read32+0x257/0x290 [i915]
[56997.639808] icl_combo_phy_verify_state.part.0+0x22/0xa0 [i915]
[56997.639808] intel_combo_phy_init+0x17e/0x3e0 [i915]
[56997.639808] ? icl_display_core_init+0x2c/0x1a0 [i915]
[56997.639808] ? _raw_spin_unlock_irqrestore+0x4c/0x60
[56997.639808] icl_display_core_init+0x34/0x1a0 [i915]
[56997.639808] intel_power_domains_init_hw+0x200/0x570 [i915]
[56997.639808] i915_driver_probe+0x103b/0x17e0 [i915]
[56997.639808] ? printk+0x53/0x6a
[56997.639808] i915_pci_probe+0x3b/0x190 [i915]
We may or may not need to change the implementation to account for DDIC
being available on other SKUs. For now I think the best thing to do is
to just disable the port.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190814235517.10032-1-lucas.demarchi@intel.com
To work around a DMC/Punit issue on ICL where the driver's
ICL_PORT_COMP_DW8/IREFGEN PHY setting is lost when entering/exiting DC6
state, make sure to reinit the PHY whenever disabling DC states.
Similarly the driver's PHY/DBUF/CDCLK settings should have been preserved
across DC5/6 transitions, so check this on all platforms.
This gets rid of the following WARN during suspend:
Combo PHY A HW state changed unexpectedly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816095523.15800-1-imre.deak@intel.com
The conversion during HDMI HW readout from port_clock to crtc_clock was
missed when HDMI 10bpc support was added, so fix that.
v2:
- Unscrew the non-HDMI case.
Fixes: cd9e11a8bf ("drm/i915/icl: Add 10-bit support for hdmi")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109593
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808162547.7009-1-imre.deak@intel.com
Our pin mapping tables for ICP and MCC currently only list the standard
GPIO pins used for various output ports. Even through ICP's standard
pin usage only utilizes pins 1, 2, and 9-12, and MCC's standard pin
usage only uses pins 1, 2, and 9, these platforms do still have GPIO
registers to address pins in the range 1-3 and 9-14. OEM's may remap
GPIO usage in non-standard ways (and provide the actual mapping via VBT
settings), so we shouldn't exclude pins on these platforms just because
they aren't part of the standard mappings.
TGP's standard pin tables contains all the possible pins, so let's
rename them to "icp" and use them for all PCH >= PCH_ICP. This will
prevent intel_gmbus_is_valid_pin from rejecting non-standard pin usage
that an OEM specifies via the VBT.
Note that this will cause pin 9 to be labeled as "tc1" instead of "dpc"
in debug messages on platforms with the MCC PCH, but that may actually
help avoid confusion since the text strings will now be the same on all
gen11+ platforms instead of being different on just EHL.
v2: Drop now-unused MCC_DDC_BUS_DDI_* names.
v3: We want to compare against INTEL_PCH_TYPE, not INTEL_PCH_ID.
Bspec: 8417
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190817005041.20651-1-matthew.d.roper@intel.com
To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.
Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-7-daniele.ceraolospurio@intel.com
They're not related to registers, so move them to the more appropriate
intel_gmbus.h
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-4-daniele.ceraolospurio@intel.com
It has nothing to do with registers, so move it to the more appropriate
intel_display_power.h
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-2-daniele.ceraolospurio@intel.com
As every i915_active_request should be serialised by a dedicated lock,
i915_active consists of a tree of locks; one for each node. Markup up
the i915_active_request with what lock is supposed to be guarding it so
that we can verify that the serialised updated are indeed serialised.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816121000.8507-2-chris@chris-wilson.co.uk
Move the active tracking for the frontbuffer operations out of the
i915_gem_object and into its own first class (refcounted) object. In the
process of detangling, we switch from low level request tracking to the
easier i915_active -- with the plan that this avoids any potential
atomic callbacks as the frontbuffer tracking wishes to sleep as it
flushes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816074635.26062-1-chris@chris-wilson.co.uk
The fb_base is only used for communicating the GTT BAR from one piece of
the display code (kms setup) to another (fbdev). What is required in the
fbdev is just the aperture address which should be derived from the
bo we allocate for the framebuffer directly.
The same appears true for drm/; it is not used by the core or the uAPI,
it is merely for conveniently passing a device address from bit of
display management code to another.
v2: Note that since we only expose enough of a system map to cover our
single framebuffer, the screen_base/size and the smem are one and the
same.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190813182112.23227-1-chris@chris-wilson.co.uk
Be more consistent with the naming of the other DMA-buf objects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/323401/
Remove the raw i915_active_request tracking in favour of the higher
level i915_active tracking for the sole purpose of making the lockless
transition easier in later patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190812174804.26180-2-chris@chris-wilson.co.uk
The DDI-IO power wells (PWR_WELL_CTL_DDI) are backing
the IO/PHY functionality, which doesn't need the PG3
power power well. Accordingly fixing up the list of
PG3 power domains.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190811100232.27964-1-anshuman.gupta@intel.com
The DDI-IO power wells (PWR_WELL_CTL_DDI) are backing
the IO/PHY functionality, which doesn't need the PG3
power power well. Accordingly fixing up the list of
PG3 power domains.
v2: Removed "DDI E/F IO"power domain as well [Imre]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190811081908.9114-1-anshuman.gupta@intel.com
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXUwPUAAKCRDj7w1vZxhR
xQ4lAQDK2ijx29YHeZspbOwP4Nwq95DFs1uQcSm5GvbRt1JSowD9EwkLeNfkPkel
Xv1Ts/Frgq7ckH2e2zkLPyCOFCHd0wA=
=rIUl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808121423.xzpedzkpyecvsiy4@flea
On TGL this register do not map directly to port, it was already
handled when setting it(TGL_TRANS_DDI_SELECT_PORT()) but not when
reading it.
To make it consisntent adding a macro for the older gens too.
v2:
Adding TGL_PORT_TRANS_DDI_SELECT() so all future users can reuse it
(Lucas)
v3:
Missed parentheses arround val (Jose)
v4:
Renamed TGL_PORT_TRANS_DDI_SELECT to TGL_TRANS_DDI_FUNC_CTL_VAL_TO_PORT
(Lucas)
Added TRANS_DDI_FUNC_CTL_VAL_TO_PORT (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808004935.1787-2-jose.souza@intel.com
When getting the pipes attached to encoder if it is not a eDP encoder
it iterates over all pipes and read a transcoder register.
But it should not read a transcoder register before get its power
domain.
It was not a issue in gens older than 12 because if it only had
port A connected it would be attached to EDP and it would skip all
the transcoders readout, if it had more than one port connected,
pipe B would cause PG3 to be on and it contains all other
transcoders.
But on gen 12 there is no EDP transcoder so it is always iterating
over all pipes and if only one sink is connected, PG3 is kept off
and reading other transcoders registers would cause a
unclaimed read warning.
So here getting the power domain of the transcoder only if it is
enabled, otherwise it is not connected to the DDI.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808004935.1787-1-jose.souza@intel.com
Blanking packet bit will control whether the transcoder allows the link
to enter the LP state during BLLP regions (assuming there is enough time),
or whether it will keep the link in the HS state with a Blanking Packet
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730073648.5157-7-vandita.kulkarni@intel.com
Latency programming remains same as that of ICL and
setting latency otimization for PCS_DW1 lanes is same as
that of EHL, hence extending it to TGL.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730073648.5157-3-vandita.kulkarni@intel.com
Increase abstraction of display suspend/resume operations by providing
higher level functions, and hiding the details inside
intel_display_power.c.
v2: Make checkpatch happy:
- braces {} are not necessary for single statement blocks
v3: Also move hsw/bdw PC8 sequences since they are related to
display PM anyways. (Ville)
v4: Rebase after a long time, plus Move functions to the new
intel_display_power so we can stop exporting platform specific
functions as pointed by Jani.
v5: Remove unnecessary braces.
v6 by Jani: make this purely non-functional cleanup, make functions static
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806122208.16786-2-jani.nikula@intel.com
Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.
There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.
v2: fix the include guard name in the renamed file
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com
Avoid including the intel_drv.h mega header from other header files to
make further header cleanup easier.
v2: restore the over-eagerly dropped <linux/types.h> (Imre)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113700.18816-1-jani.nikula@intel.com
drm function to update the content protection property state and to
generate a uevent is invoked from the intel hdcp property work.
Hence whenever kernel changes the property state, userspace will be
updated with a uevent.
v2:
state update is moved into drm function [daniel]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320965/?series=57232&rev=14
Attaches the content type property for HDCP2.2 capable connectors.
Implements the update of content type from property and apply the
restriction on HDCP version selection.
Need ACK for content type property from userspace consumer.
v2:
s/cp_content_type/content_protection_type [daniel]
disable at hdcp_atomic_check to avoid check at atomic_set_property
[Maarten]
v3:
s/content_protection_type/hdcp_content_type [Pekka]
v4:
hdcp disable incase of type change is moved into commit [daniel].
v5:
Simplified the Type change procedure. [Daniel]
v6:
Type change with UNDESIRED state is ignored.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320959/?series=57232&rev=14
This patch adds a DRM ENUM property to the selected connectors.
This property is used for mentioning the protected content's type
from userspace to kernel HDCP authentication.
Type of the stream is decided by the protected content providers.
Type 0 content can be rendered on any HDCP protected display wires.
But Type 1 content can be rendered only on HDCP2.2 protected paths.
So when a userspace sets this property to Type 1 and starts the HDCP
enable, kernel will honour it only if HDCP2.2 authentication is through
for type 1. Else HDCP enable will be failed.
Pekka have completed the Weston DRM-backend review in
https://gitlab.freedesktop.org/wayland/weston/merge_requests/48
and the UAPI for HDCP 2.2 looks good.
The userspace is accepted in Weston.
v2:
cp_content_type is replaced with content_protection_type [daniel]
check at atomic_set_property is removed [Maarten]
v3:
%s/content_protection_type/hdcp_content_type [Pekka]
v4:
property is created for the first requested connector and then reused.
[Danvet]
v5:
kernel doc nits addressed [Daniel]
Rebased as part of patch reordering.
v6:
Kernel docs are modified [pekka]
v7:
More details in Kernel docs. [pekka]
v8:
Few more clarification into kernel doc of content type [pekka]
v9:
Small fixes in coding style.
v10:
Moving DRM_MODE_HDCP_CONTENT_TYPEx definition to drm_hdcp.h [pekka]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320957/?series=57232&rev=14
- Selftests fixes and improvements (Chris)
- More work around engine tracking for better handling (Chris, Tvrtko)
- HDCP debug and info improvements (Ram, Ashuman)
- Add DSI properties (Vandita)
- Rework on sdvo support for better debuggability before fixing bugs (Ville)
- Display PLLs fixes and improvements, specially targeting Ice Lake (Imre, Matt, Ville)
- Perf fixes and improvements (Lionel)
- Enumerate scratch buffers (Lionel)
- Add infra to hold off preemption on a request (Lionel)
- Ice Lake color space fixes (Uma)
- Type-C fixes and improvements (Lucas)
- Fix and improvements around workarounds (Chris, John, Tvrtko)
- GuC related fixes and improvements (Chris, Daniele, Michal, Tvrtko)
- Fix on VLV/CHV display power domain (Ville)
- Improvements around Watermark (Ville)
- Favor intel_ types on intel_atomic functions (Ville)
- Don’t pass stack garbage to pcode (Ville)
- Improve display tracepoints (Steven)
- Don’t overestimate 4:2:0 link symbol clock (Ville)
- Add support for 4th pipe and transcoder (Lucas)
- Introduce initial support for Tiger Lake platform (Daniele, Lucas, Mahesh, Jose, Imre, Mika, Vandita, Rodrigo, Michel)
- PPGTT allocation simplification (Chris)
- Standardize function names and suffixes to make clean, symmetric and let checkpatch happy (Janusz)
- Skip SINK_COUNT read on CH7511 (Ville)
- Fix on kernel documentation (Chris, Michal)
- Add modular FIA (Anusha, Lucas)
- Fix EHL display (Matt, Vivek)
- Enable hotplug retry (Imre, Jose)
- Disable preemption under GVT (Chris)
- OA; Reconfigure context on the fly (Chris)
- Fixes and improvements around engine reset. (Chris)
- Small clean up on display pipe fault mask (Ville)
- Make sure cdclk is high enough for DP audio on VLV/CHV (Ville)
- Drop some wmb() and improve pwrite flush (Chris)
- Fix critical PSR regression (DK)
- Remove unused variables (YueHaibing)
- Use dev_get_drvdata for simplification (Chunhong)
- Use upstream version of header tests (Jani)
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdQJHXAAoJEPpiX2QO6xPKIpkH/3lMqbuv6UXyX1zvcYj6Ap4g
c6ocA7O1ooQDfFBfnLJNd6D+Gs3uTt9KROL0WdhmolfgzfLihFnvSx1VP/pvi7gC
kVT1JbwbzuwYbBXQ8WhmtkfqDp/quy3wku/ThNchY9pG1IaqNuRiP35+pXRNLO08
Q+RUHl8j1OkoLTLuzxfYGFtY72F8mIlkki8zMwlthH2Skz9h9d8POh8phOv+3TDx
aQ7CsOfScnLSrEyWlnOeYFexps0LpNC7TAG8fGkVI28Jig16DSwg7QR3MhQ9UtB1
8IC3+Jz8+p83PQHx7mGS7Va/XTERVT4czsoNC/IK7cFMy1yFilzoqpFHH8Is3sk=
=dAkP
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2019-07-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- More changes on simplifying locking mechanisms (Chris)
- Selftests fixes and improvements (Chris)
- More work around engine tracking for better handling (Chris, Tvrtko)
- HDCP debug and info improvements (Ram, Ashuman)
- Add DSI properties (Vandita)
- Rework on sdvo support for better debuggability before fixing bugs (Ville)
- Display PLLs fixes and improvements, specially targeting Ice Lake (Imre, Matt, Ville)
- Perf fixes and improvements (Lionel)
- Enumerate scratch buffers (Lionel)
- Add infra to hold off preemption on a request (Lionel)
- Ice Lake color space fixes (Uma)
- Type-C fixes and improvements (Lucas)
- Fix and improvements around workarounds (Chris, John, Tvrtko)
- GuC related fixes and improvements (Chris, Daniele, Michal, Tvrtko)
- Fix on VLV/CHV display power domain (Ville)
- Improvements around Watermark (Ville)
- Favor intel_ types on intel_atomic functions (Ville)
- Don’t pass stack garbage to pcode (Ville)
- Improve display tracepoints (Steven)
- Don’t overestimate 4:2:0 link symbol clock (Ville)
- Add support for 4th pipe and transcoder (Lucas)
- Introduce initial support for Tiger Lake platform (Daniele, Lucas, Mahesh, Jose, Imre, Mika, Vandita, Rodrigo, Michel)
- PPGTT allocation simplification (Chris)
- Standardize function names and suffixes to make clean, symmetric and let checkpatch happy (Janusz)
- Skip SINK_COUNT read on CH7511 (Ville)
- Fix on kernel documentation (Chris, Michal)
- Add modular FIA (Anusha, Lucas)
- Fix EHL display (Matt, Vivek)
- Enable hotplug retry (Imre, Jose)
- Disable preemption under GVT (Chris)
- OA; Reconfigure context on the fly (Chris)
- Fixes and improvements around engine reset. (Chris)
- Small clean up on display pipe fault mask (Ville)
- Make sure cdclk is high enough for DP audio on VLV/CHV (Ville)
- Drop some wmb() and improve pwrite flush (Chris)
- Fix critical PSR regression (DK)
- Remove unused variables (YueHaibing)
- Use dev_get_drvdata for simplification (Chunhong)
- Use upstream version of header tests (Jani)
drm-intel-next-2019-07-08:
- Signal fence completion from i915_request_wait (Chris)
- Fixes and improvements around rings pin/unpin (Chris)
- Display uncore prep patches (Daniele)
- Execlists preemption improvements (Chris)
- Selftests fixes and improvements (Chris)
- More Elkhartlake enabling work (Vandita, Jose, Matt, Vivek)
- Defer address space cleanup to an RCU worker (Chris)
- Implicit dev_priv removal and GT compartmentalization and other related follow-ups (Tvrtko, Chris)
- Prevent dereference of engine before NULL check in error capture (Chris)
- GuC related fixes (Daniele, Robert)
- Many changes on active tracking, timelines and locking mechanisms (Chris)
- Disable SAMPLER_STATE prefetching on Gen11 (HW W/a) (Kenneth)
- I915_perf fixes (Lionel)
- Add Ice Lake PCI ID (Mika)
- eDP backlight fix (Lee)
- Fix various gen2 tracepoints (Ville)
- Some irq vfunc clean-up and improvements (Ville)
- Move OA files to separated folder (Michal)
- Display self contained headers clean-up (Jani)
- Preparation for 4th pile (Lucas)
- Move atomic commit, watermark and other places to use more intel_crtc_state (Maarten)
- Many Ice Lake Type C and Thunderbolt fixes (Imre)
- Fix some Ice Lake hw w/a whitelist regs (Lionel)
- Fix memleak in runtime wakeref tracking (Mika)
- Remove unused Private PPAT manager (Michal)
- Don't check PPGTT presence on PPGTT-only platforms (Michal)
- Fix ICL DSI suspend/resume (Chris)
- Fix ICL Bandwidth issues (Ville)
- Add N & CTS values for 10/12 bit deep color (Aditya)
- Moving more GT related stuff under gt folder (Chris)
- Forcewake related fixes (Chris)
- Show support for accurate sw PMU busyness tracking (Chris)
- Handle gtt double alloc failures (Chris)
- Upgrade to new GuC version (Michal)
- Improve w/a debug dumps and pull engine w/a initialization into a common (Chris)
- Look for instdone on all engines at hangcheck (Tvrtko)
- Engine lookup simplification (Chris)
- Many plane color formats fixes and improvements (Ville)
- Fix some compilation issues (YueHaibing)
- GTT page directory clean up and improvements (Mika)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190801201314.GA23635@intel.com
According to Bspec clock divisor registers in GeminiLake
should be initialized by shifting 1(<<) to amount of correspondent
divisor. While i915 was writing all this time that value as is.
Surprisingly that it by accident worked, until we met some issues
with Microtech Etab.
v2: Added Fixes tag and cc
v3: Added stable to cc as well.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108826
Fixes: bcc6570048 ("drm/i915/glk: Program txesc clock divider for GLK")
Cc: Deepak M <m.deepak@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712081938.14185-1-stanislav.lisovskiy@intel.com
(cherry picked from commit ce52ad5dd5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
'ksv_fifo' is malloced in intel_hdcp_auth_downstream() and should be
freed before leaving from the error handling cases, otherwise it will
cause memory leak.
Fixes: f26ae6a652 ("drm/i915: SRM revocation check for HDCP1.4 and 2.2")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704104534.12508-1-weiyongjun1@huawei.com
(cherry picked from commit de70fdd7d2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to Bspec clock divisor registers in GeminiLake
should be initialized by shifting 1(<<) to amount of correspondent
divisor. While i915 was writing all this time that value as is.
Surprisingly that it by accident worked, until we met some issues
with Microtech Etab.
v2: Added Fixes tag and cc
v3: Added stable to cc as well.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108826
Fixes: bcc6570048 ("drm/i915/glk: Program txesc clock divider for GLK")
Cc: Deepak M <m.deepak@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712081938.14185-1-stanislav.lisovskiy@intel.com
With i915 added to i915_inject_probe_failure we can use dedicated
printk when injecting artificial load failure.
Also make this function look like other i915 functions that return
error code and make it more flexible to return any provided error
code instead of previously assumed -ENODEV.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190802184055.31988-2-michal.wajdeczko@intel.com
'ksv_fifo' is malloced in intel_hdcp_auth_downstream() and should be
freed before leaving from the error handling cases, otherwise it will
cause memory leak.
Fixes: f26ae6a652 ("drm/i915: SRM revocation check for HDCP1.4 and 2.2")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704104534.12508-1-weiyongjun1@huawei.com
Specification states that DDI_CLK_SEL needs to be mapped to MG clock
even if MG do not exist on EHL, this will ungate those DDIs.
BSpec: 20845
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730175121.16413-1-jose.souza@intel.com
Add hotdplug detection for all ports on TGP. icp_hpd_detection_setup()
is refactored to be shared with TGP.
While we increase the number of pins, add a BUILD_BUG_ON() to avoid
going over the number of bits allowed.
v2: use BITS_PER_TYPE and correct type for BUILD_BUG_ON() check
(requested by Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jose Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725234813.27179-2-lucas.demarchi@intel.com
Throw out our local hacks of header tests now that the more generic
kbuild versions are upstream.
At least for now, continue to keep the header tests behind
CONFIG_DRM_I915_WERROR=y knob.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190729140847.18557-1-jani.nikula@intel.com
Fix the mapping from a TBT AUX power well index to the DP_AUX_CH_CTL
register.
Fixes: c7375d9542 ("drm/i915: Configure AUX_CH_CTL when enabling the AUX power domain")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-7-imre.deak@intel.com
(cherry picked from commit 29ae36abf0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A single 32-bit PSR2 training pattern field follows the sixteen element
array of PSR table entries in the VBT spec. But, we incorrectly define
this PSR2 field for each of the PSR table entries. As a result, the PSR1
training pattern duration for any panel_type != 0 will be parsed
incorrectly. Secondly, PSR2 training pattern durations for VBTs with bdb
version >= 226 will also be wrong.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org #v5.2
Fixes: 88a0d9606a ("drm/i915/vbt: Parse and use the new field with PSR2 TP2/3 wakeup time")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111088
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204183
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: François Guerraz <kubrick@fgv6.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717223451.2595-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit b5ea9c9337)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bffb31f73b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When SAGV is forced to disabled/min/med/max in the BIOS pcode will
only hand us a single QGV point instead of the normal three. Fix
the code to deal with that instead declaring the bandwidth limit
to be 0 MB/s (and thus preventing any planes from being enabled).
Also shrink the max_bw sturct a bit while at it, and change the
deratedbw type to unsigned since the code returns the bw as
an unsigned int.
Since we now keep track of how many qgv points we got from pcode
we can drop the earlier check added for the "pcode doesn't
support the memory subsystem query" case.
Cc: felix.j.degrood@intel.com
Cc: Mark Janes <mark.a.janes@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Fixes: c457d9cf25 ("drm/i915: Make sure we have enough memory bandwidth on ICL")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110838
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606124210.3482-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 56e9371bc3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Gen2 doesn't have a frame counter and apparently we no longer provide
a fake .get_vblank_counter() hook for it. That means all tracepoints
calling that hook will oops. Update the tracepoints to use
intel_crtc_get_vblank_counter() which will gracefully fall back to
using the software counter. This is actually a better approach since
we now get (hopefully accurate) frame numbers in the traces.
This also gets rid of the raw driver->get_vblank_counter() calls, which
we need to do in order to switch to the per-crtc vblank vfuncs.
v2: Deal with new tracepoints
v3: Use a distinct variable name for the internal crtc iterator (Chris)
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 967dd48417 ("drm: remove drm_vblank_no_hw_counter assignment from driver code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619170842.20579-2-ville.syrjala@linux.intel.com
(cherry picked from commit 4c888e7bd2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bit definitions for port-select got changed for TRANS_CLK_SEL &
TRANS_DDI_FUNC_CTL registers in TGL.
v2 (Lucas):
- Nuke TRANS_DDI_PORT_NONE since it's 0: we are already clearing
{TGL_,}TRANS_DDI_PORT_MASK (suggested by Ville)
- Also cover haswell_get_ddi_port_state() in intel_display.c that was
missing
- Define macros using the _SHIFT macros so we don't lose other users
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-3-lucas.demarchi@intel.com
According to the spec when initializing the display in TGL we should not
set PORT_CL_DW12 for the Aux channel of the combo PHYs. We will re-use the
power well hooks from ICL so only set this register on gen < 12.
v2: Generalize check for gen 12 (suggested by José)
v3: Rebase after enum phy introduction
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-2-lucas.demarchi@intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/gpu/drm/i915/gem/i915_gem_mman.c: In function ‘i915_gem_fault’:
drivers/gpu/drm/i915/gem/i915_gem_mman.c:342:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!i915_terminally_wedged(i915))
^
drivers/gpu/drm/i915/gem/i915_gem_mman.c:345:2: note: here
case -EAGAIN:
^~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c: In function ‘i915_gem_object_map’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c:270:3: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(type);
^~~~~~~~~~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c:272:2: note: here
case I915_MAP_WB:
^~~~
drivers/gpu/drm/i915/i915_gpu_error.c: In function ‘error_record_engine_registers’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/i915_gpu_error.c:1196:5: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(engine->id);
^~~~~~~~~~~~
drivers/gpu/drm/i915/i915_gpu_error.c:1197:4: note: here
case RCS0:
^~~~
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_get_fia_supported_lane_count’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/display/intel_dp.c:233:3: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(lane_info);
^~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:234:2: note: here
case 1:
^~~~
drivers/gpu/drm/i915/display/intel_display.c: In function ‘check_digital_port_conflicts’:
CC [M] drivers/gpu/drm/nouveau/nvkm/engine/disp/cursgv100.o
drivers/gpu/drm/i915/display/intel_display.c:12043:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (WARN_ON(!HAS_DDI(to_i915(dev))))
^
drivers/gpu/drm/i915/display/intel_display.c:12046:3: note: here
case INTEL_OUTPUT_DP:
^~~~
Also, notice that the Makefile is modified to stop ignoring
fall-through warnings. The -Wimplicit-fallthrough option
will be enabled globally in v5.3.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/icl_dsi.c: In function 'gen11_dsi_set_transcoder_timings':
drivers/gpu/drm/i915/display/icl_dsi.c:768:6: warning:
variable 'hfront_porch' set but not used [-Wunused-but-set-variable]
It is never used and can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190719015136.103988-1-yuehaibing@huawei.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/intel_sprite.c: In function 'g4x_sprite_check_scaling':
drivers/gpu/drm/i915/display/intel_sprite.c:1494:13: warning:
variable 'src_y' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190719024100.64738-1-yuehaibing@huawei.com
A single 32-bit PSR2 training pattern field follows the sixteen element
array of PSR table entries in the VBT spec. But, we incorrectly define
this PSR2 field for each of the PSR table entries. As a result, the PSR1
training pattern duration for any panel_type != 0 will be parsed
incorrectly. Secondly, PSR2 training pattern durations for VBTs with bdb
version >= 226 will also be wrong.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: stable@vger.kernel.org
Cc: stable@vger.kernel.org #v5.2
Fixes: 88a0d9606a ("drm/i915/vbt: Parse and use the new field with PSR2 TP2/3 wakeup time")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111088
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204183
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: François Guerraz <kubrick@fgv6.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717223451.2595-1-dhinakaran.pandiyan@intel.com
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Although, DPLL4 enable and disable is associated with MGPLL1_ENABLE
register, we can use ICL_DPLL_CFGCR0/CR1 macros to access this dpll's
CR0 and CR1 registers by passing an id of 4 to these macros.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717021316.18610-1-vivek.kasireddy@intel.com
Right now we are aware of two cases that needs another hotplug retry:
- Unpowered type-c dongles
- HDMI slow unplug
Both have a complete explanation in the code to schedule another run
of the hotplug handler.
It could have more checks to just trigger the retry in those two
specific cases but why would sink signal a long pulse if there is
no change? Also the drawback of running the hotplug handler again
is really low and that could fix another cases that we are not
aware.
Also retrying for old DP ports(non-DDI) to make it consistent and not
cause CI failures if those systems are connected to chamelium boards
that will be used to simulate the issues reported in here.
v2: Also retrying for old DP ports(non-DDI)(Imre)
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-2-jose.souza@intel.com
There is some scenarios that we are aware that sink probe can fail,
so lets add the infrastructure to let hotplug() hook to request
another probe after some time.
v2: Handle shared HPD pins (Imre)
v3: Rebased
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
v5: Making the working queue used explicit through all the callers to
hotplug_work (Ville)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-1-jose.souza@intel.com
Now that we distinguish between phy and port(ddi), mcc_port_to_ddc_pin
should use the phy, not the DDI, for determining DDC pins.
We're only converting the MCC function at the moment since EHL is the
only platform that has configurations where port!=phy.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712221641.21031-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Having taken the first step in encapsulating the functionality by moving
the related files under gt/, the next step is to start encapsulating by
passing around the relevant structs rather than the global
drm_i915_private. In this step, we pass intel_gt to intel_reset.c
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712192953.9187-1-chris@chris-wilson.co.uk
Some platforms may have Modular FIA. If Modular FIA is used in the SOC,
then Display Driver will access the additional instances of
FIA based on pre-assigned offset in GTTMADDR space.
Each Modular FIA instance has its own IOSF Sideband Port ID
and it houses only 2 Type-C Port. In SOC that has more than
two Type-C Ports, there are multiple instances of Modular FIA.
Gunit will need to use different destination ID when it access
different pair of Type-C Port.
The DFLEXDPSP register has Modular FIA bit starting on Tiger Lake. If
Modular FIA is used in the SOC, this register bit exists in all the
instances of Modular FIA. IOM FW is required to program only the MF bit
in first FIA instance that houses the Type-C Port 0 and Port 1, for
Display Driver to read from.
v2 (Lucas):
- Move all accesses to FIA to be contained in intel_tc.c, along with
display_fia that is now called tc_phy_fia
- Save the fia instance number on intel_digital_port, so we don't have
to query if modular FIA is used on every access
v3 (Lucas): Make function static
v4 (Lucas): Move enum phy_fia to the header and use it in
intel_digital_port (suggested by Ville)
v5 (Lucas): Add comment about the mapping between FIA and TC port
(suggested by Stuart)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712055706.12143-2-lucas.demarchi@intel.com
intel_atomic_commit() is not for use internally, but only as an entry
point from the core drm atomic helper (drm_atomic_commit).
Squelches the warning for:
drivers/gpu/drm/i915/display/intel_display.c:14148: warning: Function parameter or member '_state' not described in 'intel_atomic_commit'
drivers/gpu/drm/i915/display/intel_display.c:14148: warning: Excess function parameter 'state' description in 'intel_atomic_commit'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712134234.29893-1-chris@chris-wilson.co.uk
CH7511 doesn't update SINK_COUNT properly so in order to detect
the device as connected we have to ignore SINK_COUNT.
In order to have access to the quirk list early enough we
must move the drm_dp_read_desc() call to happen earlier.
We can also skip re-reading this on eDP since we know it
won't change.
Cc: David S. <david@majinbuu.com>
Cc: Peteris Rudzusiks <peteris.rudzusiks@gmail.com>
Tested-by: Peteris Rudzusiks <peteris.rudzusiks@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105406
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528140650.19230-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com> #irc
Similar to the "_release" case, consistently replace mixed
"_cleanup"/"_fini"/"_fini_hw" components found in names of functions
called from i915_driver_remove() with "_remove" or "_driver_remove"
suffixes for better code readability.
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712112429.740-6-janusz.krzysztofik@linux.intel.com
Use the "_probe" nomenclature not only in i915_driver_probe() helper
name but also in other related function / variable names for
consistency. Only the userspace exposed name of a related module
parameter is left untouched.
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712112429.740-4-janusz.krzysztofik@linux.intel.com
On TGL the port programming for combophy is very similar to ICL, so
adapt the callers to possibly use the different register values.
v2 (Lucas): Add TODO with about DPLL4 (requested by Ville)
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-21-lucas.demarchi@intel.com
Make the icl function generic so it is based on phy type and can be
applied to tgl as well.
I checked if this could not apply to EHL as well, but unfortunately
there the HPD and DDC/GMBUS pins for DDI C are mapped to TypeC Port 1
even though it doesn't have TC phy.
v2: don't add a separate function for TGL, but rather reuse the ICL one
(suggested by Rodrigo)
v3: rebase after the introduction of enum phy and use it for the
conversions
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-19-lucas.demarchi@intel.com
Add default GPIO pin mapping for all ports. Tiger Lake has 3 combophy
ports and 6 TC ports, gpio pin1-3 are mapped to combophy & pin9-14 are
mapped to TC ports.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-18-lucas.demarchi@intel.com
Previously, the recommended B credit for all platforms was 24 / number
of pipes, which would give 6 for newer platforms with 4 pipes. However 6
is not enough and we need 12 on these cases.
We also need a different BW credit for these platforms.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-17-lucas.demarchi@intel.com
This patch initializes DDI PORT A, B & C for Tiger lake. Other
TC ports need to be initialized later once corresponding code is there.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-15-lucas.demarchi@intel.com
There are 2 new additional typeC ports in Tiger Lake and PORT-C is now a
combophy port. This results in 6 typeC ports and 3 combophy ports.
These 6 TC ports can be DP alternate mode, DP over thunderbolt, native
DP on legacy DP connector or native HDMI on legacy connector.
v2: Rebase on new modular FIA code (Lucas)
v3: Also add new port in port_identifier(), even though it can't
possibly be used there (requested by José)
v4: Add conversion port->tc_port in helper function after introction of
phy namespace (Lucas)
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-13-lucas.demarchi@intel.com
Add a new pll array for Tiger Lake. The TC pll functions for type C will
be covered in later patches after its phy is implemented.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-12-lucas.demarchi@intel.com
Add 2 new PLLs for additional TC ports. The names for the PLLs on TGL
changed, but most registers remained the same, like MGPLL5_ENABLE,
MGPLL6_ENABLE. So continue to use the name from ICL.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-11-lucas.demarchi@intel.com
Add power well 5 to support 4th pipe and transcoder on TGL.
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-10-lucas.demarchi@intel.com
The patch adds the new power wells introduced by TGL (GEN 12) and
maps these to existing/new power domains. The changes for GEN 12 wrt
to GEN 11 are the following:
- Transcoder#EDP removed from power well#1 (Transcoder#A used in
low-power mode instead)
- Transcoder#A is now backed by power well#1 instead of power well#3
- The DDI#B/C combo PHY ports are now backed by power well#1 instead of
power well#3
- New power well#5 added for pipe#D functionality (TODO)
- 2 additional TC ports (TC#5-6) backed by power well#3, 2 port
specific IO power wells (only for the non-TBT modes) and 4 port
specific AUX power wells (2-2 for TBT vs. non-TBT modes)
- Power well#2 backs now VDSC/joining for pipe#A instead of VDSC for
eDP and MIPI DSI (TODO)
On TGL Port DDI#C changed to be a combo PHY (native DP/HDMI) and
BSpec has renamed ports DDI#D-F to TC#4-6 respectively. Thus on ICL we
have the following naming for ports:
- Combo PHYs (native DP/HDMI):
DDI#A-B
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
DDI#C-F
Starting from GEN 12 we have the following naming for ports:
- Combo PHYs (native DP/HDMI):
DDI#A-C
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
DDI TC#1-6
To save some space in the power domain enum the power domain naming in
the driver reflects the above change, that is power domains TC#1-3 are
added as aliases for DDI#D-F and new power domains are reserved for
TC#4-6.
v2 (Lucas):
- Separate out the bits and definitions for TGL from the ICL ones.
Fix use of TRANSCODER_EDP_VDSC, that is now the correct define since
we don't define TRANSCODER_A_VDSC power domain to spare a one bit in
the bitmask (suggested by Ville)
v3 (Lucas):
- Fix missing squashes on v2
- Rebase on renamed TRANSCODER_EDP_VDSC
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-9-lucas.demarchi@intel.com
On TGL the special EDP transcoder is gone and it should be handled by
transcoder A.
v2 (Lucas):
- Reuse POWER_DOMAIN_TRANSCODER_EDP_VDSC (suggested by Ville)
- Use crtc->dev since new_crtc_state->state may be NULL on atomic
commit (suggested by Maarten)
v3 (Lucas):
- Rename power domain so it's clear it can also be used for transcoder
A in TGL (requested by José and Manasi)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-8-lucas.demarchi@intel.com
With 4:2:0 output the LS clock can be half of what it is with 4:4:4.
Make that happen.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710125851.3275-1-ville.syrjala@linux.intel.com
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Zero initialize val2 so that we don't pass stack garbage to
the pcode qgv read command. I suspect in this case pcode
just ignores the initial value in that registers, but better
safe than sorry.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190710134937.25835-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The PFI credit programming performed during cdclk change on vlv/chv
requires access to a register in the disp2d power well. So far
we've abused pipe-A power domain for this, but now we have the
more appropriate "display core" domain so let's make use of it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701161534.6671-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The spec says:
"A value of 0 indicates that this buffer does not exist"
So we should not convert a hbuf_size of 0 into 1.
Also pull the relevant code into a helper to avoid making the
same mistake multiple times.
And while at it fix the debug prints to not say "hbuf_len" twice.
v2: s/%i/%u/ in the debug (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Transition the remaining uses of intel_port_is_* over to the equivalent
intel_phy_is_* functions and drop the port functions.
v5: Fix a call in a debug function that's only called when
CONFIG_DRM_I915_DEBUG_RUNTIME_PM is on. (CI)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-5-matthew.d.roper@intel.com
Convert the code that operates directly on gen11 combo PHY's to use the
new namespace. Combo PHY registers are those named "ICL_PORT_*" plus
ICL_DPHY_CHKN.
Note that a lot of the PHY programming happens in the MIPI DSI code.
For clarity I've added a for_each_dsi_phy() to loop over the phys used
by DSI. Since DSI always uses A & B on gen11, port=phy in all cases so
it doesn't actually matter which form we use in the DSI code. I've used
the phy iterator in code that's explicitly working with the combo PHY,
but left the rest of the DSI code using the port iterator and namespace
to minimize patch deltas. We can switch the rest of the DSI code over
to use phy terminology later if this winds up being too confusing.
v6: Drop an include of drm/i915_drm.h; that was previously included just
for the definition of 'enum port' which this patch removes the need
for. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-4-matthew.d.roper@intel.com
Although the register name implies that it operates on DDI's,
DPCLKA_CFGCR0_ICL actually needs to be programmed according to the PHY
that's in use. I.e., when using EHL's DDI-D on combo PHY A, the bits
described as "port A" in the bspec are what we need to set. The bspec
clarifies:
"[For EHL] DDID clock tied to DDIA clock, so DPCLKA_CFGCR0 DDIA
Clock Select chooses the PLL for both DDIA and DDID and drives
port A in all cases."
Also, since the CNL DPCLKA_CFGCR0 bit defines are still port-based, we
create separate ICL-specific defines that accept the PHY rather than
trying to share the same bit definitions between CNL and ICL.
v5: Make icl_dpclka_cfgcr0_clk_off() take phy rather than port. When
splitting the original patch the hunk to handle this wound up too
late in the series. (Sparse)
v6: Since we're already changing this code,
s/DPCLKA_CFGCR0_ICL/ICL_DPCLKA_CFGCR0/ for consistency. (Jose)
Bspec: 33148
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-3-matthew.d.roper@intel.com
Our past DDI-based Intel platforms have had a fixed DDI<->PHY mapping.
Because of this, both the bspec documentation and our i915 code has used
the term "port" when talking about either DDI's or PHY's; it was always
easy to tell what terms like "Port A" were referring to from the
context.
Unfortunately this is starting to break down now that EHL allows PHY-A
to be driven by either DDI-A or DDI-D. Is a setup with DDI-D driving
PHY-A considered "Port A" or "Port D?" The answer depends on which
register we're working with, and even the bspec doesn't do a great job
of clarifying this.
Let's try to be more explicit about whether we're talking about the DDI
or the PHY on gen11+ by using 'port' to refer to the DDI and creating a
new 'enum phy' namespace to refer to the PHY in use.
This patch just adds the new PHY namespace, new phy-based versions of
intel_port_is_*(), and a helper to convert a port to a PHY.
Transitioning various areas of the code over to using the PHY namespace
will be done in subsequent patches to make review easier. We'll remove
the intel_port_is_*() functions at the end of the series when we
transition all callers over to using the PHY-based versions.
v2:
- Convert a few more 'port' uses to 'phy.' (Sparse)
v3:
- Switch DDI_CLK_SEL() back to 'port.' (Jose)
- Add a code comment clarifying why DPCLKA_CFGCR0_ICL needs to use PHY
for its bit definitions, even though the register description is
given in terms of DDI.
- To avoid confusion, switch CNL's DPCLKA_CFGCR0 defines back to using
port and create separate ICL+ definitions that work in terms of PHY.
v4:
- Rebase and resolve conflicts with Imre's TC series.
- This patch now just adds the namespace and a few convenience
functions; the important changes are now split out into separate
patches to make review easier.
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-2-matthew.d.roper@intel.com
PORT_TX_DFLEXDPMLE1 is a FIA register so move it to intel_tc.c where we
access other FIA registers. In Tiger Lake we have multiple/modular FIAs
so it makes sense to start moving all access to their registers to a
common place.
While at it, make it clear that we will only ever call this function
for ports with TC phy. Previously we were relying on tc_mode being
TC_PORT_TBT_ALT for combo phy ports. However it's confusing since in
this same function we have checks for is_tc_port. Also, if we manage to
make each phy access only their own field, we may in future add them as
a union inside intel_digital_port.
v2: Fix coding style while moving the code
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708172815.6814-4-lucas.demarchi@intel.com
Separate local includes with a blank line and sort the groups
alphabetically.
v2: don't make intel_tc.h be the first include
v3: don't make local includes be included first
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709155403.29370-1-lucas.demarchi@intel.com
Input CSC Co-efficients for BT601 and BT709 YCbCR to RGB
conversion were slightly off. Fixed the same.
v2: Fixed the co-eficients as there was issue with reference
matrix, spotted by Ville.
v3: Rebase
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-4-uma.shankar@intel.com
Fixed Y Pre-offset in case of Full Range YCbCr.
v2: Rebase
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-3-uma.shankar@intel.com
Currently input csc for YCbCR to RGB conversion handles only
BT601 and Bt709. Extending it to support BT2020 as well.
v2: Fixed the co-efficients for LR to FR conversion,
as suggested by Ville.
v3: Fixed Y Pre-offset in case of Full Range YCbCr as suggested
by Ville.
v4: Split the v2 and v3 changes.
v5: Rebase
v6: Fix a rebase fumble.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628080230.27492-2-uma.shankar@intel.com
For consistency clear the icl_port_dplls from the new crtc state, when
releasing the DPLLs from the old crtc state. Leaving them set could
result in releasing the same PLLs multiple times from the same CRTC
state incorrectly (if the same CRTC was first used for a TypeC port then
for a combo PHY port).
Leaving the stale pointers behind happens not to cause a problem atm
(since the incorrect releasing will be a NOP), but we need to fix that
for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-2-imre.deak@intel.com
For symmetry with the get_dplls() hook which sets the shared_dpll
pointer clear the same pointer from the put_dplls() hook.
While at it also constify the old crtc state.
v2:
- Constify the old crtc state. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708140735.20198-1-imre.deak@intel.com
Drop the redundant "SDVO_CMD_" prefix from the command name
strings in sdvo_cmd_names[].
While at it throw away the unused struct name, and undef
SDVO_CMD_NAME_ENTRY() when we're done.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Use named initializers to make it easier to associate the SDVO debug
prints with the SDVO command defines. Also switch to using ARRAY_SIZE()
instead of assuming that SDVO_CMD_STATUS_SCALING_NOT_SUPP is the last
command type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/intel_ddi.c: In function 'intel_ddi_get_config':
drivers/gpu/drm/i915/display/intel_ddi.c:3774:29: warning:
variable 'intel_dig_port' set but not used [-Wunused-but-set-variable]
struct intel_digital_port *intel_dig_port;
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705113138.65880-1-yuehaibing@huawei.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/intel_dp.c: In function 'intel_dp_set_drrs_state':
drivers/gpu/drm/i915/display/intel_dp.c:6623:24: warning:
variable 'encoder' set but not used [-Wunused-but-set-variable]
It's never used, so can be removed.Also remove related
variable 'dig_port'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705113112.64715-1-yuehaibing@huawei.com
This patch adds support for DPLL4 on EHL that include the
following restrictions:
- DPLL4 cannot be used with DDIA (combo port A internal eDP usage).
DPLL4 can be used with other DDIs, including DDID
(combo port A external usage).
- DPLL4 cannot be enabled when DC5 or DC6 are enabled.
- The DPLL4 enable, lock, power enabled, and power state are connected
to the MGPLL1_ENABLE register.
v2: (suggestions from Bob Paauwe)
- Rework ehl_get_dpll() function to call intel_find_shared_dpll() and
iterate twice: once for Combo plls and once for MG plls.
- Use MG pll funcs for DPLL4 instead of creating new ones and modify
mg_pll_enable to include the restrictions for EHL.
v3: Fix compilation error
v4: (suggestions from Lucas and Ville)
- Treat DPLL4 as a combo phy PLL and not as MG PLL
- Disable DC states when this DPLL is being enabled
- Reuse icl_get_dpll instead of creating a separate one for EHL
v5: (suggestion from Ville)
- Refcount the DC OFF power domains during the enabling and disabling
of this DPLL.
v6: rebase
v7: (suggestion from Imre)
- Add a new power domain instead of iterating over the domains
assoicated with DC OFF power well.
v8: (Ville and Imre)
- Rename POWER_DOMAIN_DPLL4 TO POWER_DOMAIN_DPLL_DC_OFF
- Grab a reference in intel_modeset_setup_hw_state() if this
DPLL was already enabled perhaps by BIOS.
- Check for the port type instead of the encoder
v9: (Ville)
- Move the block of code that grabs a reference to the power domain
POWER_DOMAIN_DPLL_DC_OFF to intel_modeset_readout_hw_state() to ensure
that there is a reference present before this DPLL might get disabled.
v10: rebase
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703230353.24059-1-vivek.kasireddy@intel.com
Split the format lists for different planes on skl/icl more cleanly.
On skl+ we have just two types of planes: those can do planar and
those that can't.
On icl we have three types of planes: hdr planes, sdr planes that
can do planar, and sdr planes that can't do planar. Those latter two
are the same set of planes we must when choose from when picking the
UV vs. Y plane for planar scanout. So we shall just designate
them sdr uv planes and sdr y planes.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-7-ville.syrjala@linux.intel.com
All sprite planes have a progammable gamma ramp. Set it up with
a linear ramp on all platforms. This actually matches the reset
value but soon we'll want to reprogram this ramp on some machines,
so let's just set it up across the board.
Note that on pre-IVB the hardware bypasses the gamma unit
unless a YCbCr pixel format is used.
v2: Add parens around << in ilk_linear_gamma()
Skip gamma programming for RGB on pre-IVB
s/DVSGAMC/DVSGAMC_G4X/
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-4-ville.syrjala@linux.intel.com
We don't currently have any use for the sprite gamma on ivb-bdw.
Let's disable it. We already do that on skl+.
On pre-ivb there is no way to disable the sprite gamma, and it
only affects YCbCr pixel formats, whereas on ivb+ it also
affects RGB formats.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-3-ville.syrjala@linux.intel.com
Plane B and C (note that we don't actually expose plane C currently)
on gen2/3 have a window generator, as does the primary plane on CHV
pipe B. So let's allow positioning of these planes freely within the
pipe source area.
Plane A on gen2/3 seems to have some kind of partial window generator
which would allow you to cut the plane off midway through the scanout,
but it would still have to start at the top-left corner of the pipe,
and it would have to be full width. That's doesn't sound all that
useful, so for simplicity let's just keep to the idea that plane A
has to be fullscreen.
Gen4 removed the plane A/B windowing support entirely, and it wasn't
reintroduced until SKL (apart from the CHV pipe B special case).
v2: s/plane/i9xx_plane/ etc. (James)
v3: Make it less confusing
v4: Deal with IS_GEN()
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190703200824.5971-2-ville.syrjala@linux.intel.com
Adding N & CTS values for 10/12 bit deep color from Appendix C
table in HDMI 2.0 spec. The correct values for N is not chosen
automatically by hardware for deep color modes.
v2: Remove unnecessary initialization of size
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627220708.31700-2-aditya.swarup@intel.com
Use port_clock to check the clock values in n/cts lookup table instead
of crtc_clock. As port_clock is already adjusted based on color mode set
(8 bit or deep color), this will help in checking clock values for deep
color modes from n/cts lookup table.
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627220708.31700-1-aditya.swarup@intel.com
When SAGV is forced to disabled/min/med/max in the BIOS pcode will
only hand us a single QGV point instead of the normal three. Fix
the code to deal with that instead declaring the bandwidth limit
to be 0 MB/s (and thus preventing any planes from being enabled).
Also shrink the max_bw sturct a bit while at it, and change the
deratedbw type to unsigned since the code returns the bw as
an unsigned int.
Since we now keep track of how many qgv points we got from pcode
we can drop the earlier check added for the "pcode doesn't
support the memory subsystem query" case.
Cc: felix.j.degrood@intel.com
Cc: Mark Janes <mark.a.janes@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Fixes: c457d9cf25 ("drm/i915: Make sure we have enough memory bandwidth on ICL")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110838
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606124210.3482-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
icl-dsi is dying on suspend/resume at
RIP: 0010:icl_update_active_dpll+0x2c/0xa0 [i915]
which appears due to the loss of the time primary_port across suspend.
Protect against the potential NULL dereference by assuming
ICL_PORT_DPLL_DEFAULT unless the port is actively specified otherwise.
Fixes: 24a7bfe0c2 ("drm/i915: Keep the TypeC port mode fixed when the port is active")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702140950.7069-1-chris@chris-wilson.co.uk
When eliminating our use of drm_irq_install() I failed to convert
all our synchronize_irq() calls to consult pdev->irq instead of
dev_priv->drm.irq. As we no longer populate dev_priv->drm.irq
we're no longer synchronizing against anything.
v2: Add intel_syncrhonize_irq() (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Imre Deak <imre.deak@intel.com>
Fixes: b318b82455 ("drm/i915: Nuke drm_driver irq vfuncs")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111012
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190702151723.29739-1-ville.syrjala@linux.intel.com
Although EHL added a third combo PHY, no PHY_MISC register was added for
PHY C. The bspec indicates that there's no need to program the "DE to
IO Comp Pwr Down" setting for this PHY that we usually need to set in
PHY_MISC.
v2:
- Add IS_ELKHARTLAKE() guards since future platforms that have a PHY C
are likely to reinstate the PHY_MISC register. (Jose)
- Use goto's to skip PHY_MISC programming & minimize code deltas. (Jose)
Bspec: 33148
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626000352.31926-4-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The port parameter hasn't been used since the last bspec phy programming
update. Drop it to make some upcoming changes simpler.
References: 9659c1af45 ("drm/i915/icl: combo port vswing programming changes per BSPEC")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626000352.31926-2-matthew.d.roper@intel.com
Lane reversal happens only in the FIA module for TBT-alt/DP-alt mode, so
WARN if lane reversal is attempted at a different level. See the
BSpec DDI_BUF_CTL register description.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-24-imre.deak@intel.com
Disconnecting the TypeC PHY when the port is in legacy mode is not
necessary:
- BSpec doesn't specify a disconnect sequence for legacy mode.
- The use of the PHY is dedicated for the display in legacy mode.
- We keep the PHY always connected during runtime as well in legacy
mode.
We disconnect the PHY when needed during a disabling modeset for the
port, so we can also remove the disconnect call from the destroy hook.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-23-imre.deak@intel.com
Add state verification for the TypeC port mode wrt. the port's AUX power
well enabling/disabling. Also check the correctness of changing the port
mode:
- When enabling/disabling the AUX power well for a TypeC port we must hold
the TypeC port lock - the case for AUX transfers - or hold a Type C
port link reference - the case for modeset enabling/disabling.
- When changing the TypeC port mode the port's AUX power domain must be
disabled.
v2: (Ville)
- Simplify power_well_async_ref_count().
- Fix the commit log, clarifying what are the valid conditions to
enable/disable the AUX power wells.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-22-imre.deak@intel.com
The TypeC port mode needs to stay fixed whenever the port is active. Do
that by introducing a tc_link_refcount to account for active ports,
avoiding changing the port mode if a reference is held.
During the modeset commit phase we also have to reset the port mode and
update the active PLL reflecting the new port mode. We can do this only
once the port and its old PLL has been already disabled. Add the new
encoder update_prepare/complete hooks that are called around the whole
enabling sequence. The TypeC specific hooks of these will reset the port
mode, update the active PLL if the port will be active and ensure that
the port mode will stay fixed for the duration of the whole enabling
sequence by holding a tc_link_refcount.
During the port enabling, the pre_pll_enable/post_pll_disable hooks will
take/release a tc_link_refcount to ensure the port mode stays fixed
while the port is active.
Changing the port mode should also be avoided during connector detection
and AUX transfers if the port is active, we'll do that by checking the
port's tc_link_refcount.
When resetting the port mode we also have to take into account the
maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt
and legacy modes, but there may be less lanes available in DP-alt mode,
in which case we have to fall back to TBT-alt mode.
While at it also update icl_tc_phy_connect()'s code comment, reflecting
the current way of switching the port mode.
v2:
- Add the update_prepare/complete hooks to the encoder instead of the
connector. (Ville)
- Simplify intel_connector_needs_modeset() by removing redundant if.
(Ville)
v3:
- Fix sparse warning, marking static functions as such.
v4:
- Rebase on drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-21-imre.deak@intel.com
When enabling a TypeC port we need to reserve all the required PLLs for
it, the TBT PLL for TBT-alt and the MG PHY PLL for DP-alt/legacy sinks.
We can select the proper PLL for the current port mode from the reserved
PLLs only once we selected and locked down the port mode for the whole
duration of the port's active state. Resetting and locking down the port
mode can in turn happen only during the modeset commit phase once we
disabled the given port and the PLL it used.
To support the above reserve-and-select PLL semantic we store the
reserved PLLs along with their HW state in the CRTC state and provide a
way to select the active PLL from these. The selected PLL along with its
HW state will be pointed at by crtc_state->shared_dpll/dpll_hw_state as
in the case of other port types.
Besides reserving all required PLLs no functional changes.
v2:
- Fix releasing the ICL PLLs, not clearing the PLLs from the old
crtc_state.
- Init port_dpll to ICL_PORT_DPLL_DEFAULT closer to where port_dpll is
used for symmetry with the corresponding ICL_PORT_DPLL_MG_PHY init.
(Ville)
v3:
- Add FIXME: for clearing the ICL port PLLs from the new crtc state.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-20-imre.deak@intel.com
For clarity factor out the combo PHY and TypeC PHY specific code from
icl_get_dplls() into their own functions.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-19-imre.deak@intel.com
Pass the PLL HW state to the PLL find/reference functions making it
clearer what is their input. Also pass to these the atomic state and the
CRTC object instead of the CRTC state, since they don't require the
latter.
Move setting the PLL in the crtc_state to the get_dpll() hook, which
is the more logical place for this, where the related PLL HW state was also
set.
This refactoring is also a preparation for a follow-up patch that will
have to find/reference multiple PLLs.
No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-18-imre.deak@intel.com
For consistency s/intel_get_shared_dpll()/intel_reserve_shared_dplls()/
to better match intel_release_shared_dplls(). Also, pass to the
reserve/release and get_dplls/put_dplls hooks the intel_atomic_state and
CRTC object, that way these functions can look up the old or new state
as needed.
Also release the PLLs from the atomic state via a new
put_dplls->intel_unreference_shared_dpll() call chain for better
symmetry with the reservation via the
get_dplls->intel_reference_shared_dpll() call chain.
Since nothing uses the PLL returned by intel_reserve_shared_dplls(),
make it return only a bool.
While at it also clarify the reserve/release function docbook headers
making it clear that multiple DPLLs will be reserved/released and
whether the new or old atomic CRTC state is affected.
This refactoring is also a preparation for a follow-up change that needs
to reserve multiple DPLLs.
Kudos to Ville for the idea to pass intel_atomic_state around, to make
things clearer locally where an object's old/new atomic state is
required.
No functional changes.
v2:
- Fix checkpatch issue: typo in code comment.
v3:
- Rebase on drm-tip.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-17-imre.deak@intel.com
Use hex numbers, since that makes more sense when decoding a bit pattern.
No functional change.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-16-imre.deak@intel.com
We must keep the TypeC port mode fixed for the duration of the connector
detection and each AUX transfers. Add a new TypeC lock holding it around
these two sequences. For consistency also hold the lock during the port
mode sanitization.
Whenever resetting the port mode (only during the detection for now) the
port's AUX power domain must be disabled already. Flush the async power
domain disabling work to ensure this.
A follow-up patch will make the port mode changing more robust by
postponing the change for active ports.
v2:
- Fix checkpatch issue: missing annotation for tc_lock.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-15-imre.deak@intel.com
For using the correct AUX power domains we have to sanitize the TypeC
port mode early, so move that before encoder sanitization. To do this
properly read out the actual port mode instead of just relying on the
VBT legacy port flag (which can be incorrect).
We also verify that the PHY is connected as expected if the port is
active. In case the port is inactive we connect the PHY in case of a
legacy port - as we did so far. The PHY will be connected during
detection for DP-alt mode - as it was done so far. For TBT-alt mode
nothing needs to be done to connect the PHY.
v2:
- Use DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER. (José)
v3:
- Detect TCCOLD any time PORT_TX_DFLEXDPCSSS is read. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-14-imre.deak@intel.com
Make the order during detection more consistent: first reset the TypeC
port mode if needed (adding new helpers for this), then detect any
connected sink.
To check if a port mode reset is needed determine first the target port
mode based on the live status if a sink is already connected or the
PHY status complete flag otherwise.
Add a WARN in legacy mode if unexpectedly we can't set the unsafe mode
or if the FIA doesn't provide the 4 lanes required.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-13-imre.deak@intel.com
Based on a recent BSpec update (Index/21750) we must handle the TCCOLD
event associated with the DP-alt mode. We can detect this event by
reading an invalid all-1s value from FIA registers.
After detecting TCCOLD we will:
- fall back to TBT-alt mode when attempting to switch to DP-alt mode
- conclude that nothing is connected during live status detection
- WARN when already in unsafe mode, since then TCCOLD is unexpected
v2:
- Use DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER. (José)
v3:
- Use 0xffffffff instead of -1 as invalid FIA reg value.
(José, Ville)
- Check for TCCOLD in icl_tc_phy_status_complete() too. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-12-imre.deak@intel.com
The PHY status complete flag normally clears when disconnecting the PHY
in DP-alt mode (achieved by switching to safe mode), so wait for the
flag to clear.
v2:
- Use DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER. (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-11-imre.deak@intel.com
Factor out helpers reading/parsing the TypeC specific registers, making
current users of them clearer and letting us use them later.
While at it also:
- Simplify icl_tc_phy_connect() with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.
Except for the last two, no functional changes.
v2:
- Don't do reg reads at variable declarations. (Jani)
- Prevent constant truncated compiler warning when assigning the
valid_hpd_mask. (Nick)
- s/intel_tc_port_get_lane_info/intel_tc_port_get_lane_mask/ (Ville)
v3:
- Make valid_hpd_mask init clear. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-10-imre.deak@intel.com
Unify the TypeC port notation in log messages, so that it matches the
spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.
v2:
- Format print the name only once. (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-9-imre.deak@intel.com
In the TypeC TBT-alt port mode we must use the TBT AUX power domain,
fix that.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-8-imre.deak@intel.com
Fix the mapping from a TBT AUX power well index to the DP_AUX_CH_CTL
register.
Fixes: c7375d9542 ("drm/i915: Configure AUX_CH_CTL when enabling the AUX power domain")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-7-imre.deak@intel.com
According to the spec we should not enable the DDI-IO power domain if
the TypeC port is in the TBT-alt mode, so do that only in the other
TypeC modes or for non-TypeC ports. See the internal BSpec Index/22243.
v2:
- Add the internal BSpec reference to the log message. (José)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-6-imre.deak@intel.com
The TypeC port mode can switch dynamically, to reflect that better call
the port's mode as 'mode' rather than 'type'.
While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/.
'TYPEC' is ambiguous, TBT_ALT and DP_ALT better match the reality.
- Remove the 'unknown' TypeC port mode. The mode is always known, it's
the TBT-alt/safe mode after HW reset and after disconnecting the PHY.
Simplify the tc_port/tc_type checks accordingly.
- Don't WARN if the port mode changes, that can happen normally.
No functional changes.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-5-imre.deak@intel.com
Move the TypeC port handling functions to a new file for clarity.
While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/
icl_tc_phy_disconnect(), will be unexported later.
- s/intel_dp_get_fia_supported_lane_count()/
intel_tc_port_fia_max_lane_count()/
It's used for HDMI legacy mode too.
- Simplify function interfaces by passing only dig_port to them.
No functional changes.
v2:
- Fix checkpatch issues: +1/-1 empty lines in intel_tc.c and add
missing SPDX to intel_tc.h. (Jani)
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-4-imre.deak@intel.com
The HW completion flag for the TBT AUX power well enabling/disabling
gets stuck if the firmware tears down the TBT DP tunnel before the
completion.
We shouldn't complain about the timeout, since it's expected to happen
and doesn't cause further issues. We suppress the disabling timeout
already, do the same for enabling.
v2:
- Make the debug message more precise. (José)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-3-imre.deak@intel.com
Add support to read out the TBT PLL HW state.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-2-imre.deak@intel.com
Pass along the correct state as much as possible, instead of relying
on the drm state internally. This is required to rely on hw state
internally soon.
While at it, clean up intel_plane_atomic_check slightly, by using a
helper function to get the intel_crtc. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628085517.31886-6-maarten.lankhorst@linux.intel.com
Like the rest of the intel atomic functions we should pass along
intel_crtc_state, and dereference drm_crtc_state only through
intel_crtc_state->base
While at it, rename old/new_state to old/new_crtc_state. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628085517.31886-4-maarten.lankhorst@linux.intel.com
Instead of passing along drm_crtc_state and drm_atomic_state, pass
along more intel_atomic_state and intel_crtc_state. This will
make the code more readable by not casting between drm state
and intel state all the time.
While at it, rename old_state to state, with the get_new/old helpers
there is no point in distinguishing between state before and after
swapping state any more. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628085517.31886-3-maarten.lankhorst@linux.intel.com
With the subdirectories we lost the ability to build individual files on
the command line, for example:
$ make drivers/gpu/drm/i915/display/intel_display.o
This was due to the top level directory missing from header search
path. Add the header search paths to subdir Makefiles.
Note that none of the other options in the top level i915 Makefile are
taken into account when building individual files. Usually this is not a
concern.
Reported-by: Imre Deak <imre.deak@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626143618.21800-2-jani.nikula@intel.com
EHL has it own voltage level requirement depending on cd clock.
BSpec: 21809
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-3-jose.souza@intel.com
EHL do not support 648 and 652.8 MHz.
v2:
- Limiting maximum CD clock by max_cdclk_freq instead of remove it
from icl_calc_cdclk()(Ville and Jani)
BSpec: 20598
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-2-jose.souza@intel.com
Now 180, 172.8 and 192 MHz are supported.
180 and 172.8 MHz CD clocks will only be used when audio is not
enabled as state by BSpec and implemented in
intel_crtc_compute_min_cdclk(), CD clock must be at least twice of
Azalia BCLK and BCLK by default is 96 MHz, it could be set to 48 MHz
but we are not reading it.
v3:
- making icl clock arrays static (Ville)
BSpec: 20598
BSpec: 15729
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-1-jose.souza@intel.com
Switch from the driver-wide vblank vfuncs to the per-crtc ones so that
we don't have so many platform specific vfuncs in the driver struct.
We still need to do something about the rest fo the irq vfuncs...
v2: s/INTEL_GEN>=3/IS_GEN3/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619170842.20579-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Gen2 doesn't have a frame counter and apparently we no longer provide
a fake .get_vblank_counter() hook for it. That means all tracepoints
calling that hook will oops. Update the tracepoints to use
intel_crtc_get_vblank_counter() which will gracefully fall back to
using the software counter. This is actually a better approach since
we now get (hopefully accurate) frame numbers in the traces.
This also gets rid of the raw driver->get_vblank_counter() calls, which
we need to do in order to switch to the per-crtc vblank vfuncs.
v2: Deal with new tracepoints
v3: Use a distinct variable name for the internal crtc iterator (Chris)
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 967dd48417 ("drm: remove drm_vblank_no_hw_counter assignment from driver code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619170842.20579-2-ville.syrjala@linux.intel.com
If LFP backlight type setting from VBT was "VESA eDP AUX Interface".
Driver should check panel capability and try to initialize aux backlight.
No matter i915_modparams.enable_dpcd_backlight was enabled or not.
v2: access dev_priv->vbt.backlight.type directly and remove unused function.
v3: 1. Modify i915.enable_dpcd_backlight type from bool to int and give default
value as 0 (disable).
2. Add a judgement to check LFP backlight type was aux interface or not.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1561045456-12171-1-git-send-email-shawn.c.lee@intel.com
- HDR support (Uma, Ville)
- Add I2C symlink under HDMI connector similar to DP (Oleg)
- Add ICL multi-segmented gamma support (Shashank, Uma)
- Update register whitelist support for new hardware (Robert, John)
- GuC firmware update with updated ABI interface (Michal, Oscar)
- Add support for new DMC header versions (Lucas)
- In-kernel blitter client for selftest use (Matthew)
- Add Mule Creec Canyon (MCC) PCH support to go with EHL (Matt)
- EHL platform feature updates (Matt)
- Use Command Transport Buffers with GuC on all gens (Daniele)
- New i915.force_probe module parameter to replace i915.alpha_support (Jani)
Refactoring:
- Better runtime PM code abstraction/encapsulation (Daniele)
- VBT parsing cleanup and improvements (Jani)
- Move display code to its own subdirectory (Jani)
- Header cleanup (Jani, Daniele)
- Prep work for subsclice mask expansion (Stuart)
- Use uncore mmio register accessors more, remove unused macro wrappers (Tvrtko)
- Remove unused atomic property get/set stubs (Maarten)
- GTT cleanups and improvements (Mika)
- Pass intel_ types instead of drm_ types in plenty of display code (Ville)
- Engine reset, hangcheck, fault code cleanups and improvements (Tvrtko)
- Consider AML variants simply as either KBL or CFL ULX (Ville)
- State checker cleanups and improvements (Ville)
- GEM code reorganization to more files under gem subdirectory (Chris)
- Reducing dependency on a coarse struct_mutex (Chris)
Fixes:
- Fix use of uninitialized/incorrect error pointers (Colin, Dan)
- Fix DSI fastboot on some VLV/CHV platforms (Hans)
- Fix DSI error path (Hans)
- Add ICL port A combo PHY HW state check (Imre)
- Fix ICL AUX-B HW not done issue (Imre)
- Fix perf whitelist on gen10+ (Lionel)
- Fix PSR exit by forcing manual exit on older gens (José)
- Match voltage ranges instead of exact values (Lucas)
- Fix SDVO HDMI audio, with cleanups (Ville)
- Fix plane state dumps (Ville)
- Fix driver cleanup code to support driver hot unbind (Janusz)
- Add checks for ICL memory bandwidth requirements (Ville)
- Fix toggling between no C8 planes vs. at least one C8 plane (Ville)
- Improved checks on PLL usage conditions, refactoring (Ville)
- Avoid clobbering M/N values in fastset fuzzy checks (Ville)
- Take a runtime pm wakeref for atomic commits (Chris)
- Do not allow runtime pm autosuspend to remove userspace GGTT mmaps too quickly (Chris)
- Avoid refcount_inc on known zero count to avoid debug flagging (Chris)
-----BEGIN PGP SIGNATURE-----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=hS8b
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2019-06-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Features:
- HDR support (Uma, Ville)
- Add I2C symlink under HDMI connector similar to DP (Oleg)
- Add ICL multi-segmented gamma support (Shashank, Uma)
- Update register whitelist support for new hardware (Robert, John)
- GuC firmware update with updated ABI interface (Michal, Oscar)
- Add support for new DMC header versions (Lucas)
- In-kernel blitter client for selftest use (Matthew)
- Add Mule Creec Canyon (MCC) PCH support to go with EHL (Matt)
- EHL platform feature updates (Matt)
- Use Command Transport Buffers with GuC on all gens (Daniele)
- New i915.force_probe module parameter to replace i915.alpha_support (Jani)
Refactoring:
- Better runtime PM code abstraction/encapsulation (Daniele)
- VBT parsing cleanup and improvements (Jani)
- Move display code to its own subdirectory (Jani)
- Header cleanup (Jani, Daniele)
- Prep work for subsclice mask expansion (Stuart)
- Use uncore mmio register accessors more, remove unused macro wrappers (Tvrtko)
- Remove unused atomic property get/set stubs (Maarten)
- GTT cleanups and improvements (Mika)
- Pass intel_ types instead of drm_ types in plenty of display code (Ville)
- Engine reset, hangcheck, fault code cleanups and improvements (Tvrtko)
- Consider AML variants simply as either KBL or CFL ULX (Ville)
- State checker cleanups and improvements (Ville)
- GEM code reorganization to more files under gem subdirectory (Chris)
- Reducing dependency on a coarse struct_mutex (Chris)
Fixes:
- Fix use of uninitialized/incorrect error pointers (Colin, Dan)
- Fix DSI fastboot on some VLV/CHV platforms (Hans)
- Fix DSI error path (Hans)
- Add ICL port A combo PHY HW state check (Imre)
- Fix ICL AUX-B HW not done issue (Imre)
- Fix perf whitelist on gen10+ (Lionel)
- Fix PSR exit by forcing manual exit on older gens (José)
- Match voltage ranges instead of exact values (Lucas)
- Fix SDVO HDMI audio, with cleanups (Ville)
- Fix plane state dumps (Ville)
- Fix driver cleanup code to support driver hot unbind (Janusz)
- Add checks for ICL memory bandwidth requirements (Ville)
- Fix toggling between no C8 planes vs. at least one C8 plane (Ville)
- Improved checks on PLL usage conditions, refactoring (Ville)
- Avoid clobbering M/N values in fastset fuzzy checks (Ville)
- Take a runtime pm wakeref for atomic commits (Chris)
- Do not allow runtime pm autosuspend to remove userspace GGTT mmaps too quickly (Chris)
- Avoid refcount_inc on known zero count to avoid debug flagging (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87v9x1lpdh.fsf@intel.com
The other additional step in the DSI sequence for EHL.
v2:
- Using REG_BIT()(Matt)
- Fixed commit message typo(Vandita)
BSpec: 20597
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619233134.20009-2-jose.souza@intel.com
EHL has 2 additional steps in the DSI sequence, this is one of then
the lane latency optimization for DW1.
BSpec: 20597
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619233134.20009-1-jose.souza@intel.com
EHL has a mux on combo PHY A that allows it to be driven either by an
internal display (DDI-A or DSI DPHY) or by an external display (DDI-D).
This is a motherboard design decision that can not be changed on the
fly. Unfortunately there are no strap registers that allow us to detect
the board configuration directly, so let's use the VBT to try to figure
it out and program the mux accordingly.
For now if we run across a broken VBT that tries to claim that PHY A
is attached to both internal and external displays at the same time,
we'll resolve the conflict in favor of the internal display. To help
debug these kind of bad VBT's, let's also add a quick DRM_DEBUG message
during child device parsing so that it's easier to understand these
cases if they show up in bug reports.
v2:
- Confirmed that VBT's dvo port refers to the DDI and not the PHY.
Thus we can check more explicitly for (ddi_d && !(ddi_a || dsi)). If
a bad VBT contradicts itself, let internal display win. (Ville)
v3:
- Switch condition from !IS_ICELAKE to IS_ELKHARTLAKE. Although the
convention is usually to assume that future platforms will inherit
all current platform behavior, this feels more like a one-platform
quirk. (Ville)
- Update commit message to describe what we do if/when we encounter
broken VBT's, and note that the new debug print during child device
parsing is intentional.
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618175131.9139-1-matthew.d.roper@intel.com
To do frontbuffer tracking we are depending on Display WA #0884 to
exit PSR when there is a frontbuffer modification but according to
user reports a write to CURSURFLIVE do not cause PSR to exit in older
gens so lets force a PSR exit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110799
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Thomas Rohwer <trohwer85@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617195154.30292-1-jose.souza@intel.com
Rename pipe_config_err() to pipe_config_mismatch(), and also print
whether we're doing the fastset check or the sw vs. hw state readout
check. Should make the logs a bit less confusing when they're not
filled with what looks like a real error.
Also rename the 'adjust' variable to 'fastset' to make it clear what
it means.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190612130801.2085-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that intel_pipe_config_compare() no longer clobbers the passed
in state we can make both crtc states const. And while at we simplify
the calling convention, and clean up intel_compare_link_m_n() a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190612130801.2085-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We're now calling intel_pipe_config_compare(..., true) uncoditionally
which means we're always going clobber the calculated M/N values with
the old values if the fuzzy M/N check passes. That causes problems
because the fuzzy check allows for a huge difference in the values.
I'm actually tempted to just make the M/N checks exact, but that might
prevent fastboot from kicking in when people want it. So for now let's
overwrite the computed values with the old values only if decide to skip
the modeset.
v2: Copy has_drrs along with M/N M2/N2 values
Cc: stable@vger.kernel.org
Cc: Blubberbub@protonmail.com
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Blubberbub@protonmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110782
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110675
Fixes: d19f958db2 ("drm/i915: Enable fastset for non-boot modesets.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190612172423.25231-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Since commit 1ba627148e ("drm: Add reservation_object to
drm_gem_object"), struct drm_gem_object grew its own builtin
reservation_object rendering our own private one bloat. Remove our
redundant reservation_object and point into obj->base.resv instead.
References: 1ba627148e ("drm: Add reservation_object to drm_gem_object")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190618125858.7295-1-chris@chris-wilson.co.uk
Although EHL introduces a new PCH, the South Display part of the PCH
that we care about is nearly identical to ICP, just with some pins
remapped. Most notably, Port C is mapped to the pins that ICP uses for
TC Port 1.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190615004210.16656-1-matthew.d.roper@intel.com
Now that we have a new subdirectory for display code, continue by moving
modesetting core code.
display/intel_frontbuffer.h sticks out like a sore thumb, otherwise this
is, again, a surprisingly clean operation.
v2:
- don't move intel_sideband.[ch] (Ville)
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-3-jani.nikula@intel.com
Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.
v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com
