[WHY]
Allow changing DET size with debug flag for testing purposes
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vendor specific link rate toggle workaround should not be
applied outside of link training scenario, such as when
outputting PHY test pattern.
[How]
Add flag to indicate when link training is occuring.
Make workaround a no-op when flag is not set.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain LTTPR require special workarounds in order to comply
with DP specifications.
[How]
Implement vendor specific sequences via DPCD writes to
vendor-specific LTTPR registers.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Adding a debugfs to show PSR capability of the panel and the driver.
To use:
cat /sys/kernel/debug/dri/0/eDP-X/psr_capability
Expected output:
Sink support: no/yes
Driver support: no/yes
[how]
Adding psr_capability to eDP connectors.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver use primary eDP link stream as the condition
to enable fastboot or not.
In dual eDP case, set second screen only,
this would cause slave eDP timing to be used on primary one.
[HOW]
Add a check for unmatched eDP link stream.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain USB4 docks do not seem to be able to handle disabling
DSC once it has been enabled on an MST stream. This can result
in blank displays.
[How]
As a work around, always enable DSC on docks exhibiting this issue. The
flag to indicate the use of DSC for MST streams on a USB4 dock is set
during detection of the dock and only cleared when the USB4 dock is
disconnected.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[HOW&WHY]
Add function to be used for early eDP power on
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Evgenii Krasnikov <Evgenii.Krasnikov@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VS and PE requested by repeater should not persist for the sink.
[How]
Clear DPCD lane settings after repeater link training finishes.
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change since v1: add brief description
1. Add hdmi frl pcon support to existing asic family.
2. Determine pcon frl capability based on pcon dpcd.
3. pcon frl is taken into consideration into mode validation.
v2: squash in warning fix (Alex)
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Parse DSC caps from PCON DPCD
2. Policy determins if DSC is decoded at PCON
3. Enable/disable DSC at PCON
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Both of split and merge are pointers, not arrays.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR currently relies on the kernel's delayed vblank on/off mechanism
as an implicit bufferring mechanism to prevent excessive entry/exit.
Without this delay the user experience is impacted since it can take
a few frames to enter/exit.
[How]
Only allow vblank disable immediate for DC when psr is not supported.
Leave a TODO indicating that this support should be extended in the
future to delay independent of the vblank interrupt.
Fixes: 92020e81dd ("drm/amdgpu/display: set vblank_disable_immediate for DC")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the bios scratch register when updating the backlight
level. Some platforms apparently read this scratch register
and do additional operations in their hotkey handlers.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1518
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A warning appears in the log on GPU reset for
link_enc_cfg_link_encs_assign for the following condition:
ASSERT(state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid == false);
This is not expected behavior and may result in link encoders being
incorrectly assigned.
[How]
The dc->current_state is backed up into dm->cached_dc_state before
we commit 0 streams.
DC will clear link encoder assignments on the real state but the
changes won't propagate over to the copy we made before the
0 streams commit.
DC expects that link encoder assignments are *not* valid
when committing a state, so as a workaround it needs to be cleared
before passing it back into DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HW interrupt gets disabled after GPU reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after GPU reset like we do for the other
DC interrupts.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <Jude.Shih@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the bios scratch register when updating the backlight
level. Some platforms apparently read this scratch register
and do additional operations in their hotkey handlers.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1518
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- FW promotion to 0.0.94
- Enable seamless boot for DCN301
- Improvements in bandwidth validation
- Fixes in flags update, link encoder assignments, DSC, ODM combine and more
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Remove tick count definition since it can be different
per HW revision
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When systme power up and eDP lit up by VBIOS,
in the core_link_enable_stream(),
the function will early return due to apply
apply_edp_fast_boot_optimization,
resulting the DP_PIXEL_COMBINE cannot get set
in enc3_dp_set_odm_combine.
[How]
Check ODM PIPE to avoid early return.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Danny Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
display_object_info_table_v1_5 with atom_display_object_path_v3
will be used.
[How]
Add bios parser support for display_object_info_table_v1_5 with
atom_display_object_path_v3 for all existing, in use bios records
as well as for new records:
ATOM_CONNECTOR_CAP_RECORD_TYPE,
ATOM_CONNECTOR_SPEED_UPTO and
ATOM_BRACKET_LAYOUT_V2_RECORD_TYPE.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to keep track of number of
references to stream pointer.
[how]
Call stream retain/release whenever
necessary in link_enc table assignment
sequence.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Rename function name so it aligns with other resource
function names being used by dcn10.
[How]
Rename function name for consistency.
Reviewed-by: Ahmad Othman <Ahmad.Othman@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A warning appears in the log on GPU reset for
link_enc_cfg_link_encs_assign for the following condition:
ASSERT(state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid == false);
This is not expected behavior and may result in link encoders being
incorrectly assigned.
[How]
The dc->current_state is backed up into dm->cached_dc_state before
we commit 0 streams.
DC will clear link encoder assignments on the real state but the
changes won't propagate over to the copy we made before the
0 streams commit.
DC expects that link encoder assignments are *not* valid
when committing a state, so as a workaround it needs to be cleared
before passing it back into DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OPTC_BYTES_PER_PIXEL calculation for 4:2:2 and 4:2:0 could have error.
[How]
Change to use following formula:
OPTC_DSC_BYTES_PER_PIXEL = ceiling((chunk size * 2^28) / slice width)
v2: squash in 64 bit divide fix (Alex)
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
* Remove restrictions on DMA_BUF_SET_NAME ioctl
* connector: State of privacy screen
* sysfs: Send hotplug uevent
Cross-subsystem Changes:
* clk/bmc-2835: Fixes
* dma-buf: Add dma_resv selftest; Error-handling fixes; Add debugfs
helpers; Remove dma_resv_get_excl_unlocked(); Documentation fixes
* pwm: Introduce of_pwm_single_xlate()
Core Changes:
* Support for privacy screens
* Make drm_irq.c legacy
* Fix __stack_depot_* name conflict
* Documentation fixes
* Fixes and cleanups
* dp-helper: Reuse 8b/10b link-training delay helpers
* format-helper: Update interfaces
* fb-helper: Allocate shadow buffer of correct size
* gem: Link GEM SHMEM and CMA helpers into separate modules; Use
dma_resv iterator; Import DMA_BUF namespace into GEM-helper modules
* gem/shmem-helper: Interface cleanups
* scheduler: Grab fence in drm_sched_job_add_implicit_dependencies();
Lockdep fixes
* kms-helpers: Link several files from core into the KMS-helper module
Driver Changes:
* Use dma_resv_iter in several places
* Fixes and cleanups
* amdgpu: Use drm_kms_helper_connector_hotplug_event(); Get all fences
at once
* bridge: Switch to managed MIPI DSI helpers in several places; Register
and attach during probe in several places; Convert to YAML in several
places
* bridge/anx7625: Support MIPI DPI input; Support HDMI audio; Fixes
* bridge/dw-hdmi: Allow interlace on bridge
* bridge/ps8640: Enable PM; Support aux-bus
* bridge/tc358768: Enabled reference clock; Support pulse mode;
Modesetting fixes
* bridge/ti-sn65dsi86: Use regmap_bulk_write(); Implement PWM
* etnaviv: Get all fences at once
* gma500: GEM object cleanups; Remove generic drivers in probe function
* i915: Support VESA panel backlights
* ingenic: Fixes and cleanups
* kirin: Adjust probe order
* kmb: Enable framebuffer console
* lima: Kconfig fixes
* meson: Refactoring to supperot DRM_BRIDGE_ATTACH_NO_ENCODER
* msm: Fixes and cleanups
* msm/dsi: Adjust probe order
* omap: Fixes and cleanups
* nouveau: CRC fixes; Validate LUTs in atomic check; Set HDMI AVI RGB
quantization to FULL; Fixes and cleanups
* panel: Support Innolux G070Y2-T02, Vivax TPC-9150, JDI R63452,
Newhaven 1.8-128160EF, Wanchanglong W552964ABA, Novatek NT35950,
BOE BF060Y8M, Sony Tulip Truly NT35521; Use dev_err_probe() throughout
drivers; Fixes and cleanups
* panel/ili9881c: Orientation fixes
* radeon: Use dma_resv_wait_timeout()
* rockchip: Add timeout for DSP hold; Suspend/resume fixes; PLL clock
fixes; Implement mmap in GEM object functions
* simpledrm: Support FB_DAMAGE_CLIPS and virtual screen sizes
* sun4i: Use CMA helpers without vmap support
* tidss: Fixes and cleanups
* v3d: Cleanups
* vc4: Fix HDMI-CEC hang when display is off; Power on HDMI controller
while disabling; Support 4k@60 Hz modes; Fixes and cleanups
* video: Convert to sysfs_emit() in several places
* video/omapfb: Fix fall-through
* virtio: Overflow fixes
* xen: Implement mmap as GEM object functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmGWF0wACgkQaA3BHVML
eiN55ggAr6QN7S7Uxu98XnqfAHC9RErY7r3PoTXXS6ODvxY41bWOpHk8TQzuw626
JCNnpQCk6Gi8L3yl8r/l1fqoirGXrfDR1YvrnmG4I9xhPxOqBmgxDWw7HQrROm2B
FctOvgFukvzn5jzQk2FqYgs5JBV20WqLrfEhttPFFMvjLGti/U31/+d+aGMJdRIQ
kE2eVpPZtAlbBAP+S4mglKp6w+WrrzNHHULSGOPcGS5jwLrNFaQg7w75JiLInzyR
RWum28USXSkKE0d6XBqHw+PWAwo3B/Vq9XSnbCX4+3GQX4tJh+hosyU7ju+rA0BY
FJCyN/YgZvc+474o/LVtMh7PbKMEHQ==
=TV6Q
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-11-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.17:
UAPI Changes:
* Remove restrictions on DMA_BUF_SET_NAME ioctl
* connector: State of privacy screen
* sysfs: Send hotplug uevent
Cross-subsystem Changes:
* clk/bmc-2835: Fixes
* dma-buf: Add dma_resv selftest; Error-handling fixes; Add debugfs
helpers; Remove dma_resv_get_excl_unlocked(); Documentation fixes
* pwm: Introduce of_pwm_single_xlate()
Core Changes:
* Support for privacy screens
* Make drm_irq.c legacy
* Fix __stack_depot_* name conflict
* Documentation fixes
* Fixes and cleanups
* dp-helper: Reuse 8b/10b link-training delay helpers
* format-helper: Update interfaces
* fb-helper: Allocate shadow buffer of correct size
* gem: Link GEM SHMEM and CMA helpers into separate modules; Use
dma_resv iterator; Import DMA_BUF namespace into GEM-helper modules
* gem/shmem-helper: Interface cleanups
* scheduler: Grab fence in drm_sched_job_add_implicit_dependencies();
Lockdep fixes
* kms-helpers: Link several files from core into the KMS-helper module
Driver Changes:
* Use dma_resv_iter in several places
* Fixes and cleanups
* amdgpu: Use drm_kms_helper_connector_hotplug_event(); Get all fences
at once
* bridge: Switch to managed MIPI DSI helpers in several places; Register
and attach during probe in several places; Convert to YAML in several
places
* bridge/anx7625: Support MIPI DPI input; Support HDMI audio; Fixes
* bridge/dw-hdmi: Allow interlace on bridge
* bridge/ps8640: Enable PM; Support aux-bus
* bridge/tc358768: Enabled reference clock; Support pulse mode;
Modesetting fixes
* bridge/ti-sn65dsi86: Use regmap_bulk_write(); Implement PWM
* etnaviv: Get all fences at once
* gma500: GEM object cleanups; Remove generic drivers in probe function
* i915: Support VESA panel backlights
* ingenic: Fixes and cleanups
* kirin: Adjust probe order
* kmb: Enable framebuffer console
* lima: Kconfig fixes
* meson: Refactoring to supperot DRM_BRIDGE_ATTACH_NO_ENCODER
* msm: Fixes and cleanups
* msm/dsi: Adjust probe order
* omap: Fixes and cleanups
* nouveau: CRC fixes; Validate LUTs in atomic check; Set HDMI AVI RGB
quantization to FULL; Fixes and cleanups
* panel: Support Innolux G070Y2-T02, Vivax TPC-9150, JDI R63452,
Newhaven 1.8-128160EF, Wanchanglong W552964ABA, Novatek NT35950,
BOE BF060Y8M, Sony Tulip Truly NT35521; Use dev_err_probe() throughout
drivers; Fixes and cleanups
* panel/ili9881c: Orientation fixes
* radeon: Use dma_resv_wait_timeout()
* rockchip: Add timeout for DSP hold; Suspend/resume fixes; PLL clock
fixes; Implement mmap in GEM object functions
* simpledrm: Support FB_DAMAGE_CLIPS and virtual screen sizes
* sun4i: Use CMA helpers without vmap support
* tidss: Fixes and cleanups
* v3d: Cleanups
* vc4: Fix HDMI-CEC hang when display is off; Power on HDMI controller
while disabling; Support 4k@60 Hz modes; Fixes and cleanups
* video: Convert to sysfs_emit() in several places
* video/omapfb: Fix fall-through
* virtio: Overflow fixes
* xen: Implement mmap as GEM object functions
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YZYZSypIrr+qcih3@linux-uq9g.fritz.box
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371a ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN301 is capable of running seamless boot
if keep_stolen_vga_memory is not set.
[How]
Add a helper to check whether an ASIC can support
seamless boot and set it based on base driver flags.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dynamic link encoder assignment expects that it can modify DC
current_state and the links associated with the incoming state when
performing full validation.
This does not align with our actual synchronization constraints
in DM's atomic_check.
[How]
Since link encoder assignment only happens as part of full validation
we can just use fast validation as part of atomic_check instead.
This satisfy's DC interface requirements and skips the DML calculations
needed for pipe programming - hopefully speeding up things a little bit
to offset the cost of double validation during stream modification.
We already do this as part of dc_commit_updates_for_stream()
with validate_bandwidth(), so extend this to dc_commit_state() as
well.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Per hardware requirements, add a flag to control
z10 enable/disable.
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HW interrupt gets disabled after GPU reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after GPU reset like we do for the other
DC interrupts.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Reviewed-by: Jude Shih <Jude.Shih@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable vblanks immediately to save power. I think this was
missed when we merged DC support.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1781
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang static analysis reports this error
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2870:7: warning:
Dereference of null pointer [clang-analyzer-core.NullDereference]
if
(top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
^
top_pipe_to_program being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function dc_sink_destruct, kfree will check pointer, no need
to check again.
This change is to cleanup the code a bit.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change is to cleanup the code a bit.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was found by coccicheck:
./drivers/gpu/drm/amd/display/dc/core/dc_resource.c, 2516, 7-9, WARNING
possible condition with no effect (if == else)
hdmi_info.bits.YQ0_YQ1 is always YYC_QUANTIZATION_LIMITED_RANGE.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After commit ("drm/amdgpu/display: add support for multiple backlights")
number of eDPs is defined while registering backlight device.
However the panel's extended caps get updated once before register call.
That leads to regression with extended caps like oled brightness control.
[How]
Update connector ext caps after register_backlight_device
Fixes: 7fd13baeb7 ("drm/amdgpu/display: add support for multiple backlights")
Link: https://www.reddit.com/r/AMDLaptops/comments/qst0fm/after_updating_to_linux_515_my_brightness/
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jasdeep Dhillon <Jasdeep.Dhillon@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Change causing issue. Need to revert the change.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix issue that secondary display goes blank on Non DCN31.
- Adjust flushing data in DMCUB
- Revert patches which cause regression in hadnling MPO/Link encoder assignment
- Correct the setting within MSA of DP2.0
- Adjustment for DML isolation
- Fix FIFO erro in fast boot sequence
- Enable DSC over eDP
- Adjust the DSC power off sequence
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.
[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Fix ARR39-C issue with scaled integer addition in rb func
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
This change allows adjustment to the Visual Confirm
height border.
[Why]
Aids debugging and testing
[How]
Use the existing infrastructure to implement logic to
draw borders
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
With eDP DSC enabled and set 4K 60Hz, there would be screen
corruption when booting to OS or enabling the driver.
[HOW]
Avoid powering down VDD when we cannot apply eDP fast boot.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous LTTPR change has caused a regression that led to an
issue where LTTPR is disabled
[HOW]
Extended changes from previous fix to DCN30X
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In fast boot sequence, when change dispclk, otg is disabled but digfe
is enabled. This may cause dig fifo error.
[How]
Reset dig fifo after enable otg.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DML itself is SW only, putting the logic as part of resource makes it
hw dependent and thus impossible to compile separately from dc.
Separate compilation is critical for unit testing as well as bbox tool
development
[how]
create new dml wrapper.
Copy logic from the validation functions into dml wrapper as base
implementation. Dml wrapper has internal/static implementations
for all helpers, and does not reference other functions.
It may reference dc structures/types for convenience.
This change now has all the changes for DML isolation squashed into
one.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a bug in MSA programming sequence that mistakenly set
MSA vsp/hsp to 1 for positive polarity. This is incorrect.
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The previous changes for fixing MPO underflow with multiple
display connected caused a regression where the machine runs
into a hang when doing multiple driver pnp with multiple displays
connected
[HOW]
Reverted offending change
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're currently flushing commands that had been previously been
flushed or are currently being processed by the DMCUB when we don't
immediately wait for idle after command execution.
[How]
Avoiding reflushing the data by keeping track of the last wptr.
We'll treat this as the actual rptr by creating a copy of the inbox
and modifying the copy's rptr.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to integration issues with branch merging,
a regression happened that prevented secondary
displays from lighting up or enabling certain features
[How]
Separated the new logic to be for DCN31 only and retained
pre DCN31 logic for all other ASICs
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ahmad Othman <Ahmad.Othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Dmesg errors are found on dcn3.1 during reset test, but it's not
a really failure. So reduce it to a debug print.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
It doesn't make sense to guard DC_LOG_DP2 by CONFIG_DRM_AMD_DCN, and
this also caused build failure for allmodconfig; So drop the guard
to fix the compile failure;
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After commit ("drm/amdgpu/display: add support for multiple backlights")
number of eDPs is defined while registering backlight device.
However the panel's extended caps get updated once before register call.
That leads to regression with extended caps like oled brightness control.
[How]
Update connector ext caps after register_backlight_device
Fixes: 7fd13baeb7 ("drm/amdgpu/display: add support for multiple backlights")
Link: https://www.reddit.com/r/AMDLaptops/comments/qst0fm/after_updating_to_linux_515_my_brightness/
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jasdeep Dhillon <Jasdeep.Dhillon@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
update developers with next level of info about unsupported
display configuration query that led to atomic check failure.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DC we want to wait for the INBOX0 HW Lock command to ACK before
continuing. This is to ensure that the lock has been successfully
acquired before programming HW in DC.
[How]
Add interfaces to send messages on INBOX0, poll for their completation
and clear the ack.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link encoder assignment tracking variables need to be (re)initialised
whenever dc_state is (re)initialised. Otherwise variables used for
dynamic encoder assignment (especially the link encoder availability
pool) are out of sync with dc_state and future encoder assignments are
invalid.
[How]
Initialise encoder assignment variables when creating new dc_state
resource.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stream ordering and count can vary from one state to the next. Only
checking a subset of entries in the encoder assignment table can lead to
invalid encoder assignments.
[How]
Check all entries in encoder assignment table when querying it.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels require to use TPS3 pattern to wake up link in PSR mode.
[How]
To add TPS3 selection information in PSR settings command and pass to
DMUB FW.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Improvements to INBOX0 HW Lock
- Add support for sending TPS3 pattern
- Fix Coverity Issues
- Fixes for DMUB
- Fix RGB MPO underflow with multiple displays
- WS fixes and code restructure
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For dpia link, link->hpd_status indicates current state, but driver
fails to capture hpd transitions in certain scenarios such as during
link training.
[How]
Added link->hpd_pending flag that captures arrival of new hpd.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Coverity discovers holes in logic that needs to be addressed for
improved code integrity.
[How]
Address issues found by coverity without changing the actual logic.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
At every reference to stream pointer, we need to increment/decrement the
kref_count. Not doing so will result in invalid stream pointer still
alive after hibernate cycle.
[how]
Call stream retain/release whenever the link encoder assignment is set
to true/false since it indicates if we want to reference the stream
pointer or not.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link encoder assignment leaves the old stream data when it was
unassigned. When the clear encoder assignment is called, it based on the
old stale data to access the de-allocated stream.
[How]
There should be no need to explicitly clean up the link encoder
assignment if the unassign loop does the work properly, the loop should
base on the current state to clean up the assignment.
Also, the unassignment should better clean up the values in the
assignement slots as well.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
According to eDP spec, DPCD 1.3 is only for eDP DPCD v1.4
In dpcd_set_link_settings function, the driver is just above v1.3
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: ChiawenHuang <chiawen.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
reduce az indirect register dump. need add az clock_gating control field
used in some project.
[how]
conditional output indrect register in the log. add clock_gating feild
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A built firmware binary may be aligned to 16-bytes with padding at the
end as necessary. In the case that padding was applied the meta info
will not be detected correctly and we won't be able to allocate the
appropriate firmware and tracebuffer sizes.
[How]
To maintain compatibility with already released firmware where this
occurs we need to try every meta offset from 0..15 inclusive.
Extract out the meta info checker into a helper function that's called
for each of these offsets and exit early when we've found it.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link_enc_cfg API operates in one of two modes depending on the stage
of application of dc_state to hardware. The API is the safest way to
query link encoder assignments.
[How]
Use results of link encoder assignment query using link_enc_cfg API.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
With RGB MPO enabled, playing a video with multiple displays connected
results in underflow when closing the video window
[HOW]
Reverted the old change to fix this problem, which prevented pipe splits
for multiple display configurations and caused high MCLK speeds during
idle. Added a two step call to dc_update_planes_and_stream, first time
with pipe split disabled and the second time with pipe split enabled,
which fixed the underflow issue
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
matching the dmcub_support with all other dcn version.
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR set power command wasn't setting panel instance
and command version which caused both streams
to overwrite the same PSR state.
[how]
Pass panel instance to the set power command function
and to DMUB and set command version enum
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. The code to blank all dp display have been called many times,
so add helpers in dc_link to make it more concise.
2. Add some check to fix the dmesg errors at boot and resume from S3
on dcn3.1 during DQE's promotion test.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since the variables named is_end_of_payload and hpd_status are already
bool type, the ?: conditional operator is unnecessary any more.
Clean them up here.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15' into drm-next
I got a drm-fixes which had some 5.15 stuff in it, so to avoid
the mess just backmerge here.
Linux 5.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
Video plane gets rejected for non-zero src_y and src_x on DCN2.x.
[How]
Limit the rejection till DCN1.x and verified MPO, by dragging video
playback beyond display's left (0, 0) co-ordinates.
Fixes: d89f6048bd ("drm/amd/display: Reject non-zero src_y and src_x for video planes")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need HPD IRQ notifications (RX, short pulse) to properly handle
DP MST for DPIA connections.
[How]
A null pointer exception currently occurs when these are received
so add a check to validate that we have a handler installed for
the notification.
Extend the HPD handler to also handle HPD IRQ (RX) since the logic is
the same.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DRM spec we only need to hold that lock when touching
connector->state - which we do not do in that handler.
Taking this locking introduces unnecessary dependencies with other
threads which is bad for performance and opens up the potential for
a deadlock since there are multiple locks being held at once.
[How]
Remove the connection_mutex lock/unlock routine and just iterate over
the drm connectors normally. The iter helpers implicitly lock the
connection list so this is safe to do.
DC link access also does not need to be guarded since the link
table is static at creation - we don't dynamically add or remove links,
just streams.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trivial patch which adds a comment for macro
endif's in amdgpu_dm.c
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
make action upon failure in "drm_atomic_add_affected_connectors()"
consistent with the rest of failures in amdgpu_dm_atomic_check().
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no reason to allow for partial buffers from userspace in our
debugfs. In this particular case callers will zero out the wr_buf but if
callers in the future don't do that we might be looking at corrupt data.
Linus puts it better than I can in
https://lkml.org/lkml/2021/10/26/993
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
In order to have dc_enable_dmub_notifications() more precise, add
one more condition to check if dc->debug.dpia_debug.bits.disable_dpia
is false.
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The MPC memory clocks should be powered down when not in use.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
write LINK_SQUARE_PATTERN_num + 1 for square pulse pattern.
Specs requirement to write this register prior to write LINK_QUAL_LANEX_SET.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
State can be cleared without removing individual streams (by
calling dc_remove_stream_from_ctx()). This can leave the
encoder assignment module in an incoherent state and cause
future assignments to be incorrect.
[How]
Clear encoder assignments when committing 0 streams or
re-initializing hardware.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In scenario when 1 display connected with pipe split (2 pipes in use)
and 3 new displays simultaneously hotplugged via MST hub (4 pipes in use),
mpcc may get reprogram to other vtg, remaining busy.
In this case waiting for mpcc idle timeouts with error like this:
[drm] REG_WAIT timeout 1us * 100000 tries - mpc2_assert_idle_mpcc
RIP: 0010:mpc2_assert_mpcc_idle_before_connect
Call Trace:
dcn20_update_mpcc
dcn20_program_front_end_for_ctx
dc_commit_state
amdgpu_dm_atomic_commit_tail
...
[How]
Add pipe split change condition to disable dangling plane.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST monitor sends link loss short pulse continuous but sink is
occupy by HDMI input to lead link training fail.
[How]
disable link once retraining fail.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Yu-ting Shen <yu-tshen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It was found that the system would hang on a dummy pstate when playing
4k60 videos on a 1080p 390Hz monitor.
[HOW]
Properly select the dummy_pstate_latency_ms when firmware assisted
memory clock switching is enabled instead of assuming that the highest
latency would work for every monitor timing.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Felipe Clark <felclark@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix spacing issue for the format string.
Addresses-Coverity-ID: 1446765: ("Invalid printf format string")
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If timing and bpp of displays on mst hub are not changed,
pbn, slot_num for displays should not be changed. Linux
user mode may initiate atomic_check with different display
configuration after set mode finished. This will call to
amdgpu_dm to re-compute payload, slot_num of displays and
saved to dm_connect_state. stream->timing.flags.dsc, pbn,
slot_num are updated to values which may be different from
that were used for set mode. when dsc hub with 3 4k@60hz dp
connected, 3 dsc engines are enabled. timing.flags.dsc = 1.
timing.flags.dsc are changed to 0 due to atomic check. when
dsc hub is unplugged, amdgpu driver check timing.flags.dsc
for last mode set and find out flags.dsc = 0, then does not
disable dsc.
[HOW]
check status of displays on dsc mst hubs. re-compute pbn,
slot_num, timing.flags.dsc only if there is mode, connect
or enable/disable change.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 652de07add ("drm/amd/display: Fully switch to dmub for all dcn21
asics") switched over to using dmub on Renoir to fix Gitlab 1735, but this
implied a new dependency on newer firmware which might not be met on older
kernel versions.
Since sw_init runs before hw_init, there is an opportunity to determine
whether or not the firmware version is new to adjust the behavior.
Cc: Roman.Li@amd.com
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1772
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1735
Fixes: 652de07add ("drm/amd/display: Fully switch to dmub for all dcn21 asics")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When updating a single connector, use
drm_kms_helper_connector_hotplug_event instead of
drm_kms_helper_hotplug_event.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018084707.32253-5-contact@emersion.fr
[Why]
- DPIA MST slot registers are not programmed during payload
allocation and hence MST does not work with DPIA.
- HPD RX interrupts are not handled for DPIA.
[How]
- Added inbox command to program the MST slots whenever
payload allocation happens for DPIA links.
- Added support for handling HPD RX interrupts
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CVE-2021-42327 was fixed by:
commit f23750b5b3
Author: Thelford Williams <tdwilliamsiv@gmail.com>
Date: Wed Oct 13 16:04:13 2021 -0400
drm/amdgpu: fix out of bounds write
but amdgpu_dm_debugfs.c contains more of the same issue so fix the
remaining ones.
v2:
* Add missing fix in dp_max_bpc_write (Harry Wentland)
Fixes: 918698d5c2 ("drm/amd/display: Return the number of bytes parsed than allocated")
Signed-off-by: Patrik Jakobsson <pjakobsson@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Notify data from outbox corrupt, the notify type should be 2 (HPD) instead of 0
(No data). We copied the address instead of the value. The memory might be
freed in the end of outbox IRQ
[How]
We should allocate the memory of notify and copy the whole content from outbox to
hpd handle function
Fixes: 88f52b1fff ("drm/amd/display: Support for SET_CONFIG processing with DMUB")
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A deadlock in the kernel occurs when we fallback from the V3 to V2
add_topology_to_display or remove_topology_to_display because they
both try to acquire the dtm_mutex but recursive locking isn't
supported on mutex_lock().
[How]
Make the mutex_lock/unlock more fine grained and move them up such that
they're only required for the psp invocation itself.
Fixes: bf62221e9d ("drm/amd/display: Add DCN3.1 HDCP support")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate
code that uses FPU in DCN301 to DML, where all FPU code
should locate.
Cc: Christian König <christian.koenig@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Zhan Liu <Zhan.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have a regression that cause maximize lane settings to use
uninitialized data from unused lanes.
This will cause link training to fail for 1 or 2 lanes because the lane
adjust is populated incorrectly sometimes.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
option 1: disallow different lanes to have different lane settings
option 2: dpcd lane settings will always use the same hw lane settings
even if it doesn't match requested lane adjust
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As DP features expands, we have encountered many situations where we
must configure a different DPCD lane setting from hw lane settings we
output. The change is to decouple hw lane settings from dpcd lane
settings to provide flexibility to configure dpcd and hw individually.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Decouple lane settings decision logic all to its own function. The
function takes in lane adjust array and link training settings and
decide what hw lane setting and dpcd lane setting should be used.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
revision 8 SCR requires DP Source to write TPS2 and FFE lane adjustment
in one 5 byte write aux transaction.
It specifies to read aux rd interval value as soon as we turn on TPS1
pattern.
Cc: Wayne Lin <wayne.lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To fix the check condition for fec enable for dpia links in MST mode.
[How]
dc_link_should_enable_fec() to be used to check whether fec should be
enabled in MST mode.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To fix the check condition for fec enable for dpia links.
[How]
dc_link_should_enable_fec() to be used to check whether fec should be
enabled.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain docks appear to NAK I2C writes to the segment pointer with the
MOT (middle of transaction) bit clear. This behaviour can cause EDID
reads from higher segments to fail.
[How]
Add workaround flag for links which connect to docks exhibiting this
issue.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
B0 has pipe mux for DIGC and DIGD which can be connected to PHYF/PHYG or
PHYC/PHY D.
[How]
Based on chip internal hardware revision id determine it is B0 and set
DMUB scratch register so DMUBFW can connect the display pipe is
connected correctly to the dig.
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hansen <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
DCN303's 4 channel SOC BB causes problems at strobe
how:
workaround to manually adjust strobe calculation using FCLK
restrict.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This new DC version brings improvements in the following areas:
- Improvements for USB4;
- Isolate FPU code for DCN20, DCN301, and DSC;
- Fixes on Linking training;
- Refactoring some parts of the code, such as PSR;
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds a config flag to allow non fullscreen MPO during ODM.
Scaling calculation will still fail configurations where video is only
one one side of the screen.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
For audio packet type 0x02, there are 2 Layouts:
Layout = 0 for 2 channels
and Layout = 1 for > 2 channels.
Layout will affect bandwidth check.
Currently, for HDMI FRL, Layout field isn't set and has a default value
of 0, so theoretically only 2-channel audio for audio packet type 0x02
is supported now.
How:
1. Set Layout properly according to maximum audio channel numbers for
audios with audio packet type 0x02.
2. 8ch LPCM audio is not supported for timing modes with v_active <= 576.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We found a compilation error that we thought was caused by the 3DLUT
patch; later on, we figured out the root cause of the problem, but we
already applied the revert in the wrong patch. This commit brings it
back the 3DLUT fix.
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add flag to control root clock gating in init_hw
- Add flag to indicate a diags environment is being used
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When writing long AUX commands some sinks will respond will write status
update requiring source to read status.
[How]
When a write request is replied with data (AUX_ACK_M), retry a read of
write status to determine when the write is completed.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the naming of preferred_training_settings is ambiguous and has
caused confusion regarding its purpose and usage.
[How]
Add comment to clarify the intention.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently there are use cases that require DP link to maintain fixed VS
and PE in HW regardless of what the sink requests. BIOS integrated info
table will specify whether we need to use the fixed drive settings, and
the drive settings to use.
[How]
Implement changes to parse the integrated info table and set the fixed
drive settings accordingly.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is unnecessary in clk_mgr
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Crash when USB4 is connected.
[How]
Added an ASIC specific code guard.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Ahmad Othman <Ahmad.Othman@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate code that uses
FPU in DSC to DML, where all FPU code should locate.
This change does not refactor any functions but move code around.
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Created new fields that matches new B0 structs On DCN31 the mapping of
DIO output to PHY differs from A0 to B0 boards with new PHY C20 & this
new mapping needed to be handled.
[How]
Mapped new structure based on new structs Added logic for mapping over
A0 and B0 boards Hooked all new structs together.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Ahmad Othman <Ahmad.Othman@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updating certain variable blanking calculations to use ceiling function.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Limit when FPU is enabled to only functions that does FPU operations for
dcn20_resource_construct, which gets called during driver
initialization.
Enabling FPU operation disables preemption. Sleeping functions(mutex
(un)lock, memory allocation using GFP_KERNEL, etc.) should not be called
when preemption is disabled.
Fixes the following case caught by enabling
CONFIG_DEBUG_ATOMIC_SLEEP in kernel config
[ 1.338434] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:281
[ 1.347395] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 197, name: systemd-udevd
[ 1.356356] CPU: 7 PID: 197 Comm: systemd-udevd Not tainted 5.13.0+ #3
[ 1.356358] Hardware name: System manufacturer System Product Name/PRIME X570-PRO, BIOS 3405 02/01/2021
[ 1.356360] Call Trace:
[ 1.356361] dump_stack+0x6b/0x86
[ 1.356366] ___might_sleep.cold+0x87/0x98
[ 1.356370] __might_sleep+0x4b/0x80
[ 1.356372] mutex_lock+0x21/0x50
[ 1.356376] smu_get_uclk_dpm_states+0x3f/0x80 [amdgpu]
[ 1.356538] pp_nv_get_uclk_dpm_states+0x35/0x50 [amdgpu]
[ 1.356711] init_soc_bounding_box+0xf9/0x210 [amdgpu]
[ 1.356892] ? create_object+0x20d/0x340
[ 1.356897] ? dcn20_resource_construct+0x46f/0xd30 [amdgpu]
[ 1.357077] dcn20_resource_construct+0x4b1/0xd30 [amdgpu]
...
Tested on: 5700XT (NAVI10 0x1002:0x731F 0x1DA2:0xE410 0xC1)
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the vbios config and driver config are different, if we update
clock to lower before call program_timing and program_pixel_clk, garbage
appear.
[How]
Align bw context with hw config when system resume
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
