[why]
driver has sent PMFW VBIOSSMC_MSG_SetDisplayIdleOptimizations while SMU
still processing a previous VBIOSSMC_MSG_SetHardMinDcfclkByFreq message.
[how]
same as RN, change the time out to2s.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The initial purpose of dcn10 pipe split is to support some high
bandwidth mode which requires dispclk greater than max dispclk. By
initial bring up power measurement data, it showed power consumption is
less with pipe split for dcn block. This could be reason for enable pipe
split by default. By battery life measurement of some Chromebooks,
result shows battery life is longer with pipe split disabled.
[How]
Disable pipe split by default. Pipe split could be still enabled when
required dispclk is greater than max dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Required for DSC MST
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reverts "drm/amd/display: Revert HUBP blank behaviour for now"
- Hubp blank will fail if the pipe is locked (this is the case on
linux), so add a check to make sure pipe isn't locked, if it is then
defer the blank to post_unlock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN30 has a bug where blanking HUBP blocks pstate allow unless
HUBP_DISABLE is toggled afterwards.
[HOW]
Create a HW sequence for blanking HUBP.
1. Wait for enter VBLANK
2. Set HUBP_BLANK
3. Make sure HUBP_IN_BLANK = 1
4. Toggle HUBP_DISABLE on and off to perform soft reset
All existing calls to hubp->funcs->set_blank should be replaced with
this new sequence.
In wait_for_mpcc_disconnect, only blank the pipe being disconnected, and
leave all other pipes unmodified.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A call to BREAK_TO_DEBUGGER is triggered when powering down memory
[How]
Remove the check for GAMCOR_MEM_PWR_STATE when powering off the memory
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot stream has hw resource assigned, already. 'add' is
actually rebuild the assignment.
[How]
Swap seamless boot stream to pipe 0 (if needed) to ensure pipe_ctx
matches
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Raymond Yang <rayyang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS reboots, and panel is turned off, T12 may not be maintained.
T12 is defined as the interval between VDDC off (occurs at shutdown) and
the next VDDC on (occurs when eDP is POST-ed)
[how]
DC already tracks panel power off time. Add a DC interface which DM can
call during shutdown. Ideally this should be as late as possible during
the shutdown sequence so the extra delay is minimal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. the corrected timing to write DPCD 300h AMD signature is before
link training.
2. and VBIOS will writes correctted AMD signature by after AGESA 1.0.0,
so driver doesn't need to write DPCD 300h again to switch config.
3. there are some OLED panel will clean backlight level to 0 once
receive DPCD 300h, so we will see flicker issue at that time.
[How]
read DPCD 300h signature before write it to avoid reprogram again, if
AMD signature was writed corrected by VBIOS, driver will not reprogram
it again.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching single pipe to split pipe, the bandwidth check is just
for first pipe. The 2nd pipe with abnormal(or zero) dpp clock when pipe
ready and unlock leads the garbage on display.
[How]
Removed external increasing dpp clock check, the internal function
already loops all of pipes to check whether update dpp clock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to make enabling test pattern a part of the stream update code
path. This change is the first step towards that goal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN10 uses plane visibility to determine when to unblank HUBP; there is
no reason DCN20+ should not do the same.
[HOW]
In addition to changing the check in HWSEQ, we must change
is_pipe_tree_visible so that it checks ODM pipe topologies as well as
MPC. Since we're now checking both ODM and MPC topologies, the helper
function names have been changed to reference "parent" and "child"
instead of "top" and "bottom".
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver apply the monitor patch into global debug flag. When apply
monitor patch, fec feature will always disable.
[How]
Separate fec debug flag and monitor patch
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The stack variable "val" is potentially unpopulate it, so initialize it
with the value 0xf (indicating an invalid mux)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_dp_set_test_pattern, we assume all pipes have a stream, which
can cause null pointer dereference.
[How]
Add a null pointer check before accessing stream.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/hw_factory.c:123:6: warning: no previous prototype for ‘dal_hw_factory_destroy’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:38: warning: Function parameter or member 'raw_state' not described in 'convert_psr_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'state' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'stream' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'dmub' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'enable' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'wait' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'psr_level' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'dmub' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'link' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'psr_context' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:284: warning: Function parameter or member 'dmub' not described in 'dmub_psr_force_static'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'residency' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'psr' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'ctx' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:332: warning: Function parameter or member 'ctx' not described in 'dmub_psr_create'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:349: warning: Function parameter or member 'dmub' not described in 'dmub_psr_destroy'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c: In function ‘dce_get_16_bit_backlight_from_pwm’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c:54:11: warning: variable ‘bl_pwm_cntl’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c:53:11: warning: variable ‘pwm_period_cntl’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:342:6: warning: no previous prototype for ‘dce_i2c_sw_engine_set_speed’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:356:6: warning: no previous prototype for ‘dce_i2c_sw_engine_acquire_engine’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:400:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_channel_request’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:443:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_payload’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_hw.c:438:35: warning: no previous prototype for ‘dce_i2c_hw_engine_wait_on_operation_result’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_hw.c:505:6: warning: no previous prototype for ‘dce_i2c_hw_engine_submit_payload’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lewis Huang <Lewis.Huang@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Excess function parameter 'ssinfo' description in 'get_ss_info_from_tbl'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:391:25: warning: no previous prototype for ‘get_engine_type’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:427:6: warning: no previous prototype for ‘dce60_opp_set_clamping’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:548:6: warning: no previous prototype for ‘dce60_opp_program_bit_depth_reduction’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:571:6: warning: no previous prototype for ‘dce60_opp_program_clamping_and_pixel_encoding’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:681:6: warning: no previous prototype for ‘dce60_opp_program_fmt’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And only declare it if it's to be used.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.c:74:6: warning: no previous prototype for ‘dce_dmcu_load_iram’ [-Wmissing-prototypes]
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.c:31:
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_scaler’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:496:7: warning: variable ‘filter_updated’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_pixel_storage_depth’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:19: warning: variable ‘expan_mode’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:6: warning: variable ‘pixel_depth’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Demote the one that provides no param descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'calc_pll_cs' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'target_pix_clk_100hz' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'ref_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'post_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'fract_feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'calc_pll_cs' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'pll_settings' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'ref_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'post_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'tolerance' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'clk_src' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pll_settings' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pix_clk_params' not described in 'dce110_get_pix_clk_dividers_helper'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1200:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1239:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_mst_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1429:6: warning: no previous prototype for ‘dce60_link_encoder_dp_set_phy_pattern’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.c: In function ‘dce110_update_generic_info_packet’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.c:70:11: warning: variable ‘regval’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: George Shen <george.shen@amd.com>
Cc: Eric Bernstein <eric.bernstein@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_audio.c:871:6: warning: no previous prototype for ‘dce60_aud_wall_dto_setup’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: Charlene Liu <Charlene.Liu@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2588:16: warning: no previous prototype for ‘update_slot_layout_info’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2692:16: warning: no previous prototype for ‘get_bracket_layout_record’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'id' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'id' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'info' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'id' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'object_id' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'info' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'bp' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'object' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'signal' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'id' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2588:16: warning: no previous prototype for ‘update_slot_layout_info’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2692:16: warning: no previous prototype for ‘get_bracket_layout_record’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Igor Kravchenko <Igor.Kravchenko@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper2.c:145: warning: Function parameter or member 't' not described in 'dal_cmd_table_helper_transmitter_bp_to_atom2'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper.c:131: warning: Function parameter or member 't' not described in 'dal_cmd_table_helper_transmitter_bp_to_atom'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'matrix' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'flt' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'buffer_size' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Excess function parameter 'param' description in 'convert_float_matrix'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw supports fp16, this is not only useful for HDR,
but also for standard dynamic range displays, because
it allows to get more precise color reproduction with
about 11 - 12 bpc linear precision in the unorm range
0.0 - 1.0.
Working fp16 scanout+display (and HDR over HDMI) was
verified on a DCE-8 asic, so i assume that the more
recent DCE-10/11 will work equally well, now that
format-specific plane scaling constraints are properly
enforced, e.g., the inability of fp16 to scale on older
hw like DCE-8 to DCE-11.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need these to support PSR on DCN302
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccinelle report:
drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c:1357:6-8:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust a jump target so that a bit of exception handling can be better
reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Return directly after a call of the function “kzalloc” failed
at the beginning.
* Delete a label which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some old ASICs might not implement/require get_dig_frontend helper; in
this scenario, we can have a NULL pointer exception when we try to call
it inside vbios disable operation. For example, this situation might
happen when using Polaris12 with an eDP panel. This commit avoids this
situation by adding a specific get_dig_frontend implementation for DCEx.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Chiawen Huang <chiawen.huang@amd.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
FP2 is not double buffered and must wait for VACTIVE
before programming.
[How]
Only update when there is a full update we should
change FP2 to avoid delay every flip.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit
latency being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
race condition of programming FP2 wrt pipe locking
and vactive state can cause underflow/black screen
[How]
Enforce the FP2 is only programmed during vactive,
and unlock pipe soon afterwards.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are missing the DP info frame update on dcn30, and this will
lead to DP SDPs not being sent;
[How]
Add the DP info frame update for dcn30;
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn30_link_encoder_validate_output_with_stream was a static function.
[How]
remove the static define and include it in the header.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many VR headsets require a HSYNC width of 4, but DCN
has default minimum of 8.
[How]
Change the arbitrary minimum HSYNC width to 4 to match
DCN20.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
some DP_SEC register defs and masks are missing.
[How]
add the missing defs and masks.
Signed-off-by: Max Tseng <chuan-yu.tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a warning that triggers when pstate takes too long.
Pstate can take up to ~200us on Linux without hanging but
it is currently set to 40us.
[How]
Change the timeout for the warning to be 180us on Linux.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CONFIG_DRM_AMD_DC_DCN3_0 is retired. drop it
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New value breaks VSR on high refresh panels, reverting until a fix is developed
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When HDCP is on, some display would introduce audio noise during
HDCP handling.
[How]
Mute before HDCP handling when disabling core link. Unmute after
HDCP when enabling core link.
Signed-off-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Without additional HostVM Latency, Renoir takes 2us longer to exit
self-refresh. This causes underflow in certain cases.
[How]
Add table for Renoir with updated sr exit latencies for WM set A.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
At very high pixel clock, bandwidth calculation exceeds 32 bit size
and overflow value. This causes the resulting selection of link rate
to be inaccurate.
[How]
Change order of operation and use fixed point to deal with integer
accuracy. Also address bug found when forcing link rate.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With the addition of dc_lock acquire before dc_link_handle_hpd_rx_irq,
there will be a deadlock situation where commit state sends a request
for payload allocation on MST and wait for HPD to process DOWN_REP.
[How]
Move forward the MST message handling in handle_hpd_rx_irq so that
it will not rely on call to dc_link_handle_hpd_rx_irq.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, the offset provided to dcn30_set_disp_pattern_generator is
not forwarded to OPP for display pattern generation, resulting in
misaligned patterns and test failures.
[How]
Use the provided offset.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change in DCN10 to use IMMEDIATE_UPDATE mode for AFMT is not
reflected in DCN30 as it uses VPG.
[How]
Use IMMEDIATE_UPDATE mode for DCN30 in VPG.
Signed-off-by: Judy Cai <HuiYi.Cai@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
power_down_on_boot is designed to power down HW when set mode is not
called before timeout. It can happen in headless system or booting with
the display is output by non-AMD GPU only.
The function will be executed only if it's not seamless boot. So in
seamless boot, the HW is still on.
It's not necessary to check this since there's no display data in both
cases.
[How]
Remove seamless boot checking in power_down_on_boot.
Signed-off-by: John Wu <john.wu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bump into calcReducedBlankingTiming because of mode query failed.
In this function,
timing.displayColorDepth == DISPLAY_COLOR_DEPTH_UNDEFINED.
Then req_bw == 0 because of bits_per_channel == 0.
So decide edp link settings, use default RBRx1 for special timing.
[How]
Set default bits_per_channel is 8.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How & Why]
Allow clk_mgr functions to be reused by making then non-static
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/vector.c:55:6: warning: no previous prototype for ‘dal_vector_presized_costruct’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/fixpt31_32.c:29:32: warning: ‘dc_fixpt_pi’ defined but not used [-Wunused-const-variable=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:34:10: warning: no previous prototype for ‘fixed_point_to_int_frac’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:81:6: warning: no previous prototype for ‘convert_float_matrix’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'dpp_input_csc_matrix' is used by some, but not all source files which
include dpp.h.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/inc/hw/dpp.h:50:42: warning: ‘dpp_input_csc_matrix’ defined but not used [-Wunused-const-variable=]
NB: Snipped lots of these for brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DPCS related info needs to be properly defined within code.
[How]
Add missing DPCS related info to code.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DSCL memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
1. Write to DSCL_MEM_PWR_FORCE to put memory to shutdown when DSCL is not
used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While booting into OS, driver updates DPP/DISP CLKs.
But init clock value is zero which is invalid.
[How]
Get current clocks value to update init clocks.
To avoid underflow.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable_link_dp_mst checks that cur_link_settings != unknown to determine
that the link is already enabled, to skip redundant enablement calls for
multiple streams on the same link. During dc_reinitialize_hardware,
cur_link_settings on previously-active links is not cleared, which blocks
MST links from being re-enabled after a reinitialization.
[How]
- check for link_status->link_active instead, as it's the real intent
- clear cur_link_settings when we clear link_active
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
does that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HDR3DLUT and SHAPER memory blocks should be powered down when
they're not in use. This will reduce power consumption.
[How]
1. Write to HDR3DLUT_MEM_PWR_FORCE to put memory to shutdown
when HDR3DLUT is not used.
2. Write to SHAPER_MEM_PWR_FORCE to put memory to shutdown
when SHAPER is not used.
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 2208f39c75.
It caused a regression in internal FPGA tests.
Signed-off-by: Eric Bernstein <Eric.Bernstein@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Set dpms off on the connector that was unplugged, for the side effect of
releasing some references held through deallocation of MST payload. This is
the expected behaviour for non MST devices as well.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Recent changes to upstream mst code remove the callback which
cleared the internal state for mst. Move the missing functionality
that was previously called through the destroy call back for mst connector
destroy
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cached backlight is never being updated since panel_cntl specific
registers were moved from abm to panel_cntl.
[How]
Update cached backlight in set_abm_immediate_disable as what we used to
do. Also, update the priority of backlight restore mechanism so that
cached backlight has the highest priority since it is always correct.
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ASIC requirement.
[how]
Make disable_*_power_gate to false.
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The GAMCOR memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
Write to GAMCOR_MEM_PWR_FORCE to put memory to shutdown
when GAMCOR is not used.
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Remove temp macro since the enum is in header file already.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
only apply multiple display power optimization in case there are more
than one internal display.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Get internal display info from vbios and pass it to dmub fw to determine
if multiple display optmization is needed.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The BLNDGAM memory blocks should be powered down when they're not in
use. This will reduce power consumption.
[How]
1. Write to BLNDGAM_MEM_PWR_FORCE to put memory to shutdown when BLNDGAM
is not used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
t9 delay func is called twice after setting power off, the unexpected
action results in a doubling of the added 140ms t9 delay
[How]
If the backlight has been turned off, does not turn it off again
Signed-off-by: Sherry <Yao.Wang1@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPCC may change and request data when the pipes are switching from 2
to 1 or 1 to 2. During the switch there is a possibility of underflow
and flicker/missing data.
[How]
During VBlank the MPCC won't request data. The trick is to delay and
wait on VBlank, ONLY when pipes are either turning on or off, right
before MPCC is reset for the pipes.
Signed-off-by: Tashfique Abdullah <tabdullah@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, DMCU is no longer used. In these cases, some DMCU
memory should be completely powered off to save power.
[How]
1. Set DMCU_ERAM_MEM_PWR_FORCE to shutdown memory when DMCU is not in
use
2. Added a debug option to allow this behaviour to be turned off
3. Set all memory low power debug options to off first, to not
immediately cause problems
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect panel register settings are applied for power sequence because
the register macro is not defined in resource.
[How]
Implement same register space to future resource files.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum HBlank supported by
the ASIC.
[How]
Make the ASIC minimum HBlank available in Source Device information
address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
slower down the HW i2c speed when used by HW i2c.
this request: each acquired_i2c_engine setup the i2c speed needed.
and set the I2c engine for HDCP use at release_engine.
this covers SW using HW I2c engine and HDCP using HW I2c engine. for
dmcu using HW I2c engine, needs add similar logic in dmcufw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple break statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn302 link encoder regs list, so add them.
Just like dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Update bounding box as per spread sheet.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After removing added latency for HostVM by default, DDR4 sr exit
latencies were no longer large enough for some panels and caused
underflow.
[How]
Add 1us to sr enter/exit watermark.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should use int for counting variable
[How]
Change type from bool to uint32_t
Signed-off-by: Raymond Yang <rayyang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Instead of calculating CRC on whole frame, add flexibility to calculate
CRC on specific frame region.
[How]
Add few crc window coordinate properties. By default, CRC is calculated
on whole frame unless user space specifies the CRC calculation window.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add a dual edp power optimization flag, so driver will
notify this flag to dmub FW to determine if apply the
power optimization.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Blue screen when PNP with multiple monitor or hotplug external monitor when playing video
due to dpp dto isn't programmed properly.
If lower dpp clock, dpp dto need to be programmed first, and actual dpp clk not avalable yet.
[How]
set dpp dto as per request clk for lower case before dpp clk update, and after dpp clk updated
set dpp dto again with actual dpp clk.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Check if the eDP sink supports the dynamic backlight control
[How]
Query the dynamic backlight capability in DPCD (eDP case only)
Signed-off-by: Roy Chan <roy.chan@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is missing on displays 2 and up when doing rotated
display groups in 1xnY setup. Calculation puts cursor
out of bounds so it is not enabled.
[How]
In dcn10_set_cursor_position(), add in viewport.y into cursor
calculations for 1xnY rotated display groups.
For pipe split, check viewport.y for both pipes and use lower one
to normalize cursor position before calculations.
Add odm 2:1 support ( using same calculations as pipe split ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently if VBIOSSMC_Result_UnknownCmd is returned as result of smu msg
there is no way to know. Put 1 in param so if 1 is returned, this unknown case is handled.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.
[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Use GPINT command to get PSR residency from FW.
[How]
Hook up PSR residency command to DSAT.
Since PSR Count Request is deprecated, we will use this.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpp dto phase and modulo are programmed with actual dpp global clk
and pipe clk. Need to use actual dpp clk to prgoram dpp dto modulo
to get more accuracy ratio.
[How]
assign actual dpp clk to dccg for dpp modulo programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes >200 warnings.
Fixes the following W=1 kernel build warning(s):
from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:31:
drivers/gpu/drm/amd/amdgpu/../display/include/ddc_service_types.h:126:22: warning: ‘DP_DVI_CONVERTER_ID_5’ defined but not used [-Wunused-const-variable=]
126 | static const uint8_t DP_DVI_CONVERTER_ID_5[] = "3393N2";
| ^~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/ddc_service_types.h:125:22: warning: ‘DP_DVI_CONVERTER_ID_4’ defined but not used [-Wunused-const-variable=]
125 | static const uint8_t DP_DVI_CONVERTER_ID_4[] = "m2DVIa";
| ^~~~~~~~~~~~~~~~~~~~~
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes >200 warnings.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/include/ddc_service_types.h:123:22: warning: ‘DP_VGA_LVDS_CONVERTER_ID_3’ defined but not used [-Wunused-const-variable=]
123 | static const uint8_t DP_VGA_LVDS_CONVERTER_ID_3[] = "dnomlA";
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/ddc_service_types.h:121:22: warning: ‘DP_VGA_LVDS_CONVERTER_ID_2’ defined but not used [-Wunused-const-variable=]
121 | static const uint8_t DP_VGA_LVDS_CONVERTER_ID_2[] = "sivarT";
NB: Repeated ~100 times - snipped for brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the FP handling to avoid nested calls.
The nested calls cause the warning below
WARNING: CPU: 3 PID: 384 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin
Fixes: 582e2ce5b4 ("drm/amdgpu/display: FP fixes for DCN3.x (v4)")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also rid some unused ones.
This patch solves 2000 warnings!
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dc_types.h:33,
from drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services_types.h:30,
from drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services.h:35,
from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_helpers.c:35:
At top level:
drivers/gpu/drm/amd/amdgpu/../display/include/fixed31_32.h:76:32: warning: ‘dc_fixpt_ln2_div_2’ defined but not used [-Wunused-const-variable=]
76 | static const struct fixed31_32 dc_fixpt_ln2_div_2 = { 1488522236LL };
| ^~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/fixed31_32.h:75:32: warning: ‘dc_fixpt_ln2’ defined but not used [-Wunused-const-variable=]
75 | static const struct fixed31_32 dc_fixpt_ln2 = { 2977044471LL };
| ^~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/fixed31_32.h:74:32: warning: ‘dc_fixpt_e’ defined but not used [-Wunused-const-variable=]
74 | static const struct fixed31_32 dc_fixpt_e = { 11674931555LL };
| ^~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/fixed31_32.h:73:32: warning: ‘dc_fixpt_two_pi’ defined but not used [-Wunused-const-variable=]
73 | static const struct fixed31_32 dc_fixpt_two_pi = { 26986075409LL };
| ^~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/include/fixed31_32.h:72:32: warning: ‘dc_fixpt_pi’ defined but not used [-Wunused-const-variable=]
72 | static const struct fixed31_32 dc_fixpt_pi = { 13493037705LL };
| ^~~~~~~~~~~
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
4K monitor shows corruption if dpp dto phase is larger than modulo.
[How]
cap phase value never larger than modulo.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Actual dpp/disp clock PMFW set are always equal or more than requested.
Need to cache the actual clock for debugging purpose.
[How]
Add actuall dpp/disp clk in clock manager and save it when set clocks.
Add an ASSERT in case of actual clock less than requested.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't want GSL to be enabled when only updating
plane address
[How]
Only check other pipes for immediate flip if GSL is
already enabled
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to make sure all immediate flips are completed before locking
the pipes, but not pipes that are not flip immediate as they will be
locked by the OTG
[How]
Skip non flip immediate pipes when checking for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The intended use is to force PSR into active state and ignore all
events until explicit EXIT.
A new event force_static is added to power module. It is then sent
to FW.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, prefetch mode 0 is unsupported but prefetch 1 is
supported. Due to previous change always forcing prefetch mode to 0, we
are failing bandwidth validation in cases where we should not.
[How]
By default try prefetch mode 0 but in the case validation fails, attempt
to do prefetch mode 1 to see if it is supported.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently we are using dcn3 reg headers for dcn302. The offsets are
different between the two so they need seperate headers.
Add dcn302 header files and use these instead of dcn3 header
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add proper FP_START/END handling and adjust Makefiles per
previous asics.
v2: fix up harder.
v3: fix clkmgr Makefile for dcn30
v4: fix old gcc handling is only required for x86
Build-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change for correct asic type check
caused a psr regression due to incorrect
chip family id for Raven.
[How]
Use correct family id.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix typoes.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect values were resulting in flash lines
when MPO was enabled and system was left idle.
[How]
Increase min clk values only when MPO is enabled
and display is active to not affect S3 power.
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Recout calculation does not corrrectly handle plane
clip rect that extends beyond the left most border
of stream source rect. This change adds handling by
truncating the invisible clip rect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Commit "Blank HUBP during pixel data blank for DCN30 v2"
modifies HW behaviour during blank, which might have OS
dependencies. We need to assess the impact on amdgpu_dm
and only re-enable HUBP blanking when all necessary
changes are understood.
[How]
- revert functional changes
- leave architectural changes intact
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Customer make a request to add this WA by driver.
Some MUX chips will power down with eDP 1.4 panel and
lose previous supported link rates(DPCD 0x010) in
customer's hybrid-GPU designs. As a result, during sleep
resuming and screen turns on from idle, link training
will be performed incorrectly and eDP will flicker or
black screen. These MUX chips need source to read DPCD
0x010 again during LKT so that it can restore supported
link rates of panel.
For driver side, supported link rate set is fetched when
link detection, no need to update but just read again
as WA.
[How]
Read DPCD 0x010 again during link training for eDP 1.4.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently, we only support calculating CRC on whole frame.
We want to extend the capability to calculate CRC on
specific frame area.
[how]
Calculate CRC on specific area once it's specified from the
input parameter.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prior commit "Blank HUBP during pixel data blank for DCN30"
missed the call to set_disp_pattern_generator from
set_crtc_test_pattern, which re-exposed the issue for which
we initially blocked active-only p-state switching.
[How]
- remove dcn30_blank_pixel_data, set dcn30 back to dcn20 version
- new hwss funciton set_disp_pattern_generator
- dcn20 version just calls opp_set_disp_pattern_generator
- dcn30 version implements the HUBP blank
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When checking if we want to disable GSL or not,
we should reset flip_immediate to be the flip type
of the topmost plane before looping through the
other planes.
[How]
Set flip_immediate to be the flip type of the topmost
plane before looping through the other planes.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current end of T9 delay is relay on polling
sink status by DPCD. But the polling for sink
status change after NoVideoStream_flag set to 0.
[How]
Add function edp_add_delay_for_T9 to add T9 delay.
Move the sink status polling after blank.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OPTC memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Set ODM_MEM_UNASSIGNED_PWR_MODE to shutdown memory when unassigned
2. Set ODM_MEM_VBLANK_PWR_MODE to light sleep mode when in vblank
3. Added a debug option to allow this behaviour to be turned off
4. Restructured debug options to use a bitfield in a way that's more clear
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect panel register settings are
applied for power sequence because the
register macro is not defined in resource.
[How]
Implement same register space to future
resource files.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If pbn_per_slot is 0, fail instead of dividing by zero and
bugchecking.
[how]
Check for zero divisor before division operation.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some timings for which we support p-state
switching in active, but not in blank. There was a
previous issue where a timing that had active-only
support would hang a p-state request when we were in
an extended blanking period. The workaround for that
issue was to block active-only p-state switching,
but that resulted in a lack of p-state support for
some common timings such as 1440p60. We want to fix
that issue properly by un-blocking p-state requests
while the display is blanked, so that we can re-enable
active-only p-state switching.
[How]
- new version of blank_pixel_data for DCN30
- call hubp->set_blank from dcn30_blank_pixel_data
- blank every hubp in the mpcc tree, and odm tree
- on blank enable, wait until the next frame before blanking HUBP
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver keeps the invalid information cause report the
incorrect monitor which save in remote sink to OS
[How]
When connector type change from MST to non-MST,
stop the topology manager.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling PIP in Heaven, the PIP planes are VSYNC
flip and is also the top-most pipe. In this case GSL
will be disabled because we only check immediate flip
for the top pipe. However, the desktop planes are still
flip immediate so we should at least keep GSL on until
the full update.
[How]
Check each pipe in the tree to see if any planes
are flip immediate. Maintain the GSL lock if yes,
and take it down after when unlocking if any planes
are flipping VSYNC. Keeping GSL on with VSYNC +
flip immediate planes causes corruption.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On APU should be always using prefetch mode 0.
Currently, sometimes prefetch mode 1 is being
used causing system to hard hang due to
minTTUVBlank being too low.
[How]
Any ASIC running DCN21 will by default allow
self refresh and mclk switch. This sets both
min and max prefetch mode to 0 by default.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. only need to check first ODM pipe.
2. Only need to check eDP which is on.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPC memory blocks in DCN3 should be powered down completely when
they are not in use. This will reduce power consumption.
[How]
This commits changes behaviour for dcn3 and does the following:
1. Write to MPC_RMU<X>_LOW_PWR_MODE and MPCC_OGAM_MEM_LOW_PWR_MODE to
automatically shut down memory when not in use
2. mpc3_power_on_shaper_3dlut and mpc3_power_on_ogam_lut are called
to disable force power on when configuration finishes
3. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The C standard does not specify whether an enum is signed or unsigned.
In the function prototype, one of the argument is defined as an enum
but its declaration was unit32_t. Fix this by changing the function
argument to enum in the declaration.
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Signed-off-by: Florin Iucha <florin.iucha@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
core_link_write_dpcd() returns enum dc_status, not ddc_result:
display/dc/core/dc_link_dp.c: In function 'dp_set_panel_mode':
display/dc/core/dc_link_dp.c:4237:11: warning: implicit conversion from 'enum dc_status' to 'enum ddc_result'
[-Wenum-conversion]
Avoid the warning by using the correct enum in the caller.
Fixes: 0b22632243 ("drm/amd/display: Synchronous DisplayPort Link Training")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccinelle report:
./drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:1367:3-5:
WARNING: possible condition with no effect (if == else)
Both branches are the same, so remove the if/else altogether.
Fixes: 81875979f0 ("drm/amd/display: Remove extra pairs of parentheses in dce_calcs.c")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's unused and identical to dal_cmd_tbl_helper_dce112_get_table2.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate config option at this point.
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need this to pass dp compliance.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes this warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_ddc.c: In function ‘defer_delay_converter_wa’:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_ddc.c:285:2: warning: this ‘if’ clause does not guard... [-Wmisleading-indentation]
285 | if (link->dpcd_caps.branch_dev_id == DP_BRANCH_DEVICE_ID_0080E1 &&
| ^~
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_ddc.c:291:3: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
291 | if (link->dpcd_caps.branch_dev_id == DP_BRANCH_DEVICE_ID_006037 &&
| ^~
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required for MALL. Was accidently removed in PSR update.
Fixes: 48e48e5984 ("drm/amd/display: Disable idle optimization when PSR is enabled")
Fixes: 52f2e83e2f ("drm/amdgpu/display: add MALL support (v2)")
Acked-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check chip family also to avoid wrong identification.
V2: use the correct macro without AMDGPU prefix
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch simplifies the ASSERT*() and BREAK_TO_DEBUGGER() macros:
- Move the dependency check of CONFIG_KGDB into Kconfig
- Unify the kgdb_breakpoint() call
- Drop the non-existing CONFIG_HAVE_KGDB
Also align the behavior of ASSERT() macro in both cases with and
without CONFIG_DEBUG_KERNEL_DC.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ASSERT_CRITICAL() invokes kgdb_breakpoint() whenever either
CONFIG_KGDB or CONFIG_HAVE_KGDB is set. This, however, may lead to a
kernel panic when no kdb stuff is attached, since the
kgdb_breakpoint() call issues INT3. It's nothing but a surprise for
normal end-users.
For avoiding the pitfall, make the kgdb_breakpoint() call only when
CONFIG_DEBUG_KERNEL_DC is set.
https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently both error code paths handled in dal_gpio_open_ex() issues
ASSERT_CRITICAL(), and this leads to a kernel panic unnecessarily if
CONFIG_KGDB is enabled. Since basically both are non-critical errors
and can be recovered, drop those assert calls and use a safer one,
BREAK_TO_DEBUGGER(), for allowing the debugging, instead.
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It looks this was accidently lost in a follow up patch.
dc context is large and we don't need contiguous pages.
Fixes: e4863f118a ("drm/amd/display: Multi display cause system lag on mode change")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Alex Xu <alex_y_xu@yahoo.ca>
Reported-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Tested-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
[why]
Some platform has a limitation of 2ms for udelay
[how]
Add 1ms udelay for specific dongle.
Signed-off-by: jinlong zhang <jinlong.zhang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The clock state update is the source of many problems, and capturing
this sort of information helps debug. This commit introduces tracepoints
for capturing clock values and also add traces in DCE, DCN1, DCN2x, and
DCN3.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit introduces a trace mechanism for struct pipe_ctx by adding a
middle layer struct in the amdgpu_dm_trace.h for capturing the most
important data from struct pipe_ctx and showing its data via tracepoint.
This tracepoint was added to dc.c and dcn10_hw_sequencer, however, it
can be added to other DCN architecture.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our DC currently uses some of the tracepoint function inside a DC
header, which means that many other files implicitly include part of the
trace function. This situation limits how we can expand this feature for
other parts of the driver by generating multiple compilation errors when
we try to reuse some of the existing structures. This commit decouples
part of the amdgpu_dm_trace from DC core to simplify the trace
enlargement in future changes.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
oem-related ddc read/write fails without these regs
how:
copy from hw_factory_dcn20.c
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When ODM combine is in use we trigger multiple update events causing
issues with variable refresh rate.
[How]
Only trigger on a single ODM instance.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not
[How]
Check for updating GSL state whenever we're not doing
immediate flip
v2: Squash in build fix (Alex)
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
VBIOS will not enable VSC_SDP during pre-OS to lead
MISC1[6] wasn't matched with driver.
[HOW]
disabled seamless boot if sink supports VSC_SDP
Signed-off-by: Yu-Ting Shen <Yu-ting.Shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
right side visual confirm is too thick due to it is 4 times of
left side (16 lines).
[How]
Change factor from 4 to 2.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some monitors,
they can't display under BIOS with avmute enabled.
[How]
Add monitor patch for skip avmute action.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All DCN3x resources share ABM_MASK_SH_LIST_DCN301 definition.
The naming is misleading since it looks like DCN30 code
depends on next version DCN301, which in fact is vice-versa.
[How]
Refactor the naming to ABM_MASK_SH_LIST_DCN30.
v2: squash in build fixes (Alex)
Signed-off-by: Roman Li <roman.li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
missing OEM data to control graphics card functions
how:
load it into init_data. copied over from dcn2 implementation.
copied destruction sequence as well.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Currently disable 48mhz debug option only disables on boot.
Need to put option check in update_clocks as well to make it
affect more areas.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Can be used for debug purposes
[How] Add max target bpp override field and related handling
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
So we can track VSC SDP errors from display
[how]
Define the bit, and use it in driver logic
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow counter increases in AGM when performing some mode switches due
to timing sync, which is a known hardware issue.
[How]
Temporarily raise DPG height during timing sync so that underflow is not
reported.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If full pstate is not supported, we should set WM set A
to 0 to prevent any hangs
[How]
If pstate is not supported, set watermark set A to 0
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Create a separate dcn21_fast_validate_bw function for dcn21.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DF PState and Voltage State are coupled such that one cannot be
raised without raising the other. This uses more power than
is necessary in high bandwidth scenarios.
[HOW]
Add logic to create a new bounding box state that allows for
DF PState to be low while Voltage State is high. Watermarks
vlevel calculation logic was also udpated to assume
state 1 contains the new optimized state.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
get_pixel_clk_frequency_100hz is undefined in clock_source_funcs.
[how]
set function pointer: ".get_pixel_clk_frequency_100hz = get_pixel_clk_frequency_100hz"
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable Memory Access at Last Level (MALL) feature for display.
v2: squash in 64 bit division fixes
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A break is not needed if it is preceded by a return or break
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some setups will fail to build. So copy dcn301 makefile setup
which is known to work
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Functions (disable_all_writeback_pipes_for_stream &
dc_enable_stereo & dc_post_update_surfaces_to_stream)
always return true, there is no need to keep the return value.
This change is to make the code a bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display Core support for green_sardine
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It was recently introduced a change that enables driver to disable
streams if pixel clock changes. Consequently, the code path executed in
the disable vbios function expanded to an encoder verification part.
The encoder loop is nested inside the pipe count loop, and both loops
share the 'i' variable in control of their flow. This situation may lead
to an infinite loop because the encoder loop constantly updates the `i`
variable, making the first loop always positive. As a result, we can see
a soft hang during the module load (modprobe amdgpu) and a series of
dmesg log that looks like this:
kernel:[ 124.538727] watchdog: BUG: soft lockup - CPU#2 stuck for 22s!
[modprobe:1000]
RSP: 0018:ffffabbf419bf0e8 EFLAGS: 00000282
RAX: ffffffffc0809de0 RBX: ffff93b35ccc0000 RCX: ffff93b366c21800
RDX: 0000000000000000 RSI: 0000000000000141 RDI: ffff93b35ccc0000
RBP: ffffabbf419bf108 R08: ffffabbf419bf164 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000003 R12: 0000000008677d40
R13: 0000000000000141 R14: ffff93b35cfc0000 R15: ffff93b35abc0000
FS: 00007f1400717540(0000) GS:ffff93b37f680000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005649b66b0968 CR3: 00000003e0fec000 CR4: 0000000000350ee0
Call Trace:
amdgpu_device_rreg+0x17/0x20 [amdgpu]
amdgpu_cgs_read_register+0x14/0x20 [amdgpu]
dm_read_reg_func+0x3a/0xb0 [amdgpu]
get_pixel_clk_frequency_100hz+0x30/0x50 [amdgpu]
dc_commit_state+0x8f1/0xae0 [amdgpu]
? drm_calc_timestamping_constants+0x101/0x160 [drm]
amdgpu_dm_atomic_commit_tail+0x39d/0x21a0 [amdgpu]
? dcn21_validate_bandwidth+0xe5/0x290 [amdgpu]
? kfree+0xc3/0x390
? dcn21_validate_bandwidth+0xe5/0x290 [amdgpu]
...
RSP: 002b:00007fff26009bd8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055a8025bea50 RCX: 00007f140085c89d
RDX: 0000000000000000 RSI: 000055a8025b8290 RDI: 000000000000000c
RBP: 0000000000040000 R08: 0000000000000000 R09: 0000000000000000
R10: 000000000000000c R11: 0000000000000246 R12: 000055a8025b8290
R13: 0000000000000000 R14: 000055a8025bead0 R15: 000055a8025bea50
This issue was fixed by introducing a second variable for the internal
loop.
Fixes: 8353d30e74 ("drm/amd/display: disable stream if pixel clock changed with link active")
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These function pointers are missing from dcn30_init
.calc_vupdate_position : Used to help avoid cursor stuttering
.set_pipe : Needed for setting ABM
So add them
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When forcing 3D mode in DAL, we set the right address to be the same as the
left address. We need to do the same for the meta addresses.
[How]
Program right meta to be same as left meta.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently construction of clock limits gets skipped for diags.
This logic would be useful to get tested in diags.
[HOW]
Copy existing states to clk_table such that update_bw_bounding_box
logic gets used to fill the table.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be programmed with timing rather than with odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable ODM on eDP panel with ABM will result in color difference
on the panel due to only one ABM module to set one pipe.
[How]
Block ABM in case of ODM enabled on eDP.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we transfer the WM range table to SMU, they can perform a watermark
switch right away. This can be a problem if we're in not in accelerated mode
during hw_init as SMU may initiate a dummy p-state change before the rest
of the watermarks are programmed. Watermark set A is defined to be
sufficient for all cases, so we can copy the values from set A to all other
sets, avoiding any issues from SMU doing WM switches.
[How]
- new hubbub func init_watermarks
- copy register values from set A to all other sets
- call init_watermarks before calling notify_wm_ranges
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running games or benchmarking with v-sync disabled, disabling
a plane (which is v-sync) can cause underflow. This is caused by
flips pending before pipe locking being applied after locks are
released and pipes could have been re-arranged or disconnected. This
could potentially apply a flip on incorrect pipe. Also, previous logic
of always locking pipes was unnecessary.
[How]
Only lock the pipes when there is a pipe being disabled to increase
efficiency. Before the pipes are locked, check that any pending flips
are cleared to ensure the flips are applied to the correct pipe.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We will hang if we report switch in VACTIVE but not in VBLANK and DPG_EN = 1
[How]
Block switch in ACTIVE if not supported in BLANK
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently mode validation is bypassed if remote sink exists. That
leads to mode set issue when a BW bottle neck exists in the link path,
e.g., a DP-to-HDMI converter that only supports HDMI 1.4.
Any invalid mode passed to Linux user space will cause the modeset
failure due to limitation of Linux user space implementation.
[How]
Mode validation is skipped only if in edid override. For real remote
sink, clock limit check should be done for HDMI remote sink.
Have HDMI related remote sink going through mode validation to
elimiate modes which pixel clock exceeds BW limitation.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Formula uses kHz in their formula while our driver operates with Hz.
[How]
Divide audio rate by 1000 on the initial variable that is entered into formula.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sometimes CRTCs can be disabled due to display unplugging or temporarily
transition in the userspace; in these circumstances, DCE tries to set
the minimum clock threshold. When we have this situation, the function
bw_calcs is invoked with number_of_displays set to zero, making DCE set
dispclk_khz and sclk_khz to zero. For these reasons, we have seen some
ATOM bios errors that look like:
[drm:atom_op_jump [amdgpu]] *ERROR* atombios stuck in loop for more than
5secs aborting
[drm:amdgpu_atom_execute_table_locked [amdgpu]] *ERROR* atombios stuck
executing EA8A (len 761, WS 0, PS 0) @ 0xEABA
[How]
This error happens due to an attempt to optimize the bandwidth using the
sclk, and the dispclk clock set to zero. Technically we handle this in
the function dce112_set_clock, but we are not considering the case that
this value is set to zero. This commit fixes this issue by ensuring that
we never set a minimum value below the minimum clock threshold.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add code to gracefuly handle any pipe reassignment
occuring on dcn3 hardware. This should only happen when new
surfaces are used for an update rather than old ones updated.
Fixes: 69fc1f4b97 ("amd/drm/display: avoid dcn3 on flip opp change for slave pipes")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 78fe9f6394 ("drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions")
added a call to rn_vbios_smu_get_smu_version() to set clk_mgr->smu_ver.
That field is initialized prior to the if-statement, already.
Fixes: 78fe9f6394 (drm/amd/display: Remove DISPCLK Limit Floor for Certain SMU Versions)
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sung Lee <sung.lee@amd.com>
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This addresses the following sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2740:6:
warning: symbol 'dce110_set_cursor_position' was not declared. Should it
be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:2785:6:
warning: symbol 'dce110_set_cursor_attribute' was not declared. Should
it be static?
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This addresses the following sparse warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_hw_sequencer.c:180:26:
warning: symbol 'get_color_space_type' was not declared. Should it be
static?
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
At the moment on flip opp reassignment does not work in all cases
for non root pipes.
This change simply makes sure we prefer pipes not used previously
when splitting in dcn3.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vbios uses preferred timing to turn on edp but OS could use other
timing. If change pixel clock when link active, there is unexpected
garbage on monitor.
[How]
Once pixel clock changed, the driver needs to disable stream.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
At the moment, some tests are failing because cur_link_settings is
invalid. As a workaround, add an option to force dio disable.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, when full p-state changes are not supported, DLG parameters
are calculated for no p-state support at all. However, we are required
to always support dummy p-state changes, so we should instead calculate
DLG based on dummy p-state latency when full p-state is unsupported.
This behaviour already exists for DCN2.
[How]
- move DLG calculation inside WM calculation
- if p-state unsupported, do not recalculate for set A, instead copy from
set C, and perform DLG calculation with dummy p-state latency
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vbios uses preferred timing to turn on edp but OS could use other
timing. If change pixel clock when link active, there is unexpected
garbage on monitor.
[How]
Once pixel clock changed, the driver needs to disable stream.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some debug bits are not being copied from driver to fw.
[How]
Copy debug bits properly.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly handle clang and older versions of gcc.
Fixes: e77165bf7b ("drm/amd/display: Add DCN3 blocks to Makefile")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the function dal_ddc_service_query_ddc_data,
get rid of dal_ddc_i2c_payloads_destroy, call
dal_vector_destruct() directly.
This change is to make the code run a bit fast.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Changes since V1:
*get rid of dal_ddc_i2c_payloads_destroy, call
dal_vector_destruct() directly.
Link for V1:
*https://lore.kernel.org/patchwork/patch/1309014/
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI requires fallback to TMDS by redetection
in order to switch PHY settings.
This avoids black out when link training fail
during mode setting, link quality update,
disable driver sequence.
[How]
Allow driver to redetect HDMI displays
based on retraining or fallback mechanism.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running a game/benchmark with v-sync disabled, disabling a plane
(which is v-sync) can cause an underflow. This is due to flips that are
pending before pipe locking being applied after locks are released and
pipes have been re-arranged or disconnected. This can potentially apply
a flip on the incorrect pipe.
[How]
Check that any pending flips are cleared before locking any pipes to
ensure flips are applied on the correct pipes.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DMUB implementation of PSR, the 'wait' parameter,
used to determine if driver should wait for PSR enable/disable,
is not implemented correctly.
[How]
Implement wait for PSR enable/disable.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Regression is caused by previous change with attempt to correct the
extended cr aux rd interval delay due to mis interpretation of the DP specs.
The change turns out not working well with certain RXs.
So we decided to keep the cr aux rd interval logic as before.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In DCN10 when a panel with YCbCr420 capability is connected via
USB-C to HDMI active dongle, no YCbCr420 option is listed in
Radeon settings.
[HOW]
Enable DP YCbCr420 mode support for DCN10
Signed-off-by: Gary Li <gary.li@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When disabling DP video, the current REG_WAIT timeout
of 50ms is too low for certain cases with very high
VSYNC intervals.
[HOW]
Increase the timeout to 102ms, so that
refresh rates as low as 10Hz can be handled properly.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
[WHY]
Only the leftmost ODM pipe should be offset when scaling. A previous
code change was intended to implement this policy, but a section of code
was overlooked.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.
[How]
Power off eDP backlight before power off eDP
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dce_is_panel_backlight_on() will return wrong value if
LVTMA_BLON_OVRD is 0
[How]
When LVTMA_BLON_OVRD is 0, read
LVTMA_PWRSEQ_TARGET_STATE instead
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warnig:
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c:282:12-42:
duplicated argument to && or ||
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:3240:12-42:
duplicated argument to && or ||
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:5520:7-91:
duplicated argument to && or ||
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:5309:86-122:
duplicated argument to && or ||
Fixes: 6725a88f88 ("drm/amd/display: Add DCN3 DML")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
linux-next kernel test robot reported the following problem:
warning: no previous prototype for 'dce60_get_dp_ref_freq_khz' [-Wmissing-prototypes]
[How]
mark dce60_get_dp_ref_freq_khz() as static
Fixes: 3ecb3b794e "drm/amd/display: dc/clk_mgr: add support for SI parts (v2)"
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"Copy GSL groups when committing a new context" patch was accidentally
removed during a refactor
Patch: 21ffcc94d5 ("drm/amd/display: Copy GSL groups when committing a new context")
[How]
Re add it
Fixes: b6e881c947 ("drm/amd/display: update navi to use new surface programming behaviour")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In fnction is_cr_done & is_ch_eq_done, when done = false
happened once, no need to circle left ln_count.
This change is to make the code run a bit fast.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix spellos of "function" in drivers/gpu/drm/amd/display/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove duplicate header which is included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot skip porgram clock when set path mode.
It cause driverprogram clock after unblank stream.
[How]
update clock when non-seamless boot stream exist
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values
[how]
Parse the values from VBIOS if available, and use
them if valid
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
psr doesn't get fully disabled before hitting hubbub1_wm_change_req_wa.
[How]
Pass TRUE to "wait" parameter to get psr fully disabled.
Follow-Up fix to:
dc: PSR eDP p-state warning occurs intermittently after unplug DP
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Recent characterization shows increased stutter latencies on some SKUs,
leading to underflow.
[how]
Update SOC params to account for this worst case latency.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
gcc version 5.4.0 fails compilation with:
‘PixelPTEReqHeightPTEs’ may be used uninitialized in this function
[-Werror=maybe-uninitialized]
[How]
Initialized variable explicitly with 0
Signed-off-by: Roman Li <roman.li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Send stream active state info to DMUB
[How]
Implement GPINT to notify stream mask
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
some functions may need be dependent on stutter period in the future
how:
Extract from stutter calculations and place into perf_params structure
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows us to reuse these on different asics.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCValidator is created/destroyed repeatedly for cofunctional validation
which causes a lot of memory thrashing, particularly when Driver Verifer
is enabled.
[How]
Implement a basic caching algorithm that will cache DCValidator with a
matching topology. When a match is found, the DCValidator can be
reused. If there is no match, a new one will be created and inserted
into the cache if there is space or an unreference entry can be evicted.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Idle optimization and PSR conflict each other. If both enabled
at the same time, display flickering will be observed.
[How]
Disable idle optimization when PSR is enabled.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are situations where we go from 2 pipe to 1 pipe in MPO, but this
isn't a pipe split being lost -- it's a plane disappearing in (i.e. video overlay
goes away) so we lose one pipe. In these situations we don't want to
disable the pipe in a separate operation from the rest of the pipe
programming sequence. We only want to disable a pipe in a
separate operation when we're actually disabling pipe split.
[How]
Make sure the pipe being lost has the same stream AND plane
as the old top pipe to ensure.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR needs to be enabled on DCN30. This is the driver part of PSR
enablement.
Also disabled retired DMCU on driver side, since DMCU is
not supported on DCN30 anymore.
[How]
Add necessary changes to enable PSR on DCN30.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When pipe locks are being taken we wait for flip pending to clear first.
In some cases the pipe mapping is changed and the pending we're checking
for will never clear.
[How]
Don't check disabled pipes for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When link training failures occur for eDP, dp_disable_link_phy
is called which powers OFF eDP panel. After link training retry
delay, the next retry begins by calling dp_enable_link_phy
which does not issue a correspnding eDP panel power ON, leaving
panel powered OFF which leads to display OFF/dark.
[how]
Power ON eDP before next link training retry.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only the first pipe in ODM combine group should have nonzero recout
offset. All other pipes should have recout offset 0;
otherwise there will be gaps in the image.
[HOW]
Set recout.x to 0 if the pipe is not the leftmost ODM pipe.
When computing viewports, calculate the horizontal offset of a pipe's src
based on the current pipe's position in the ODM group, plus whatever offset the
leftmost ODM pipe has; otherwise there will be discontinuity in the image.
Since ODM combine can only combine pipes horizontally, nothing needs to
be done for recout.y.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The cr training aux rd interval is
modified without following specs requirements.
According to the commit message the change was not intended to modify the value.
Therefore it looks like it is caused by a typo in the change.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the load processes for Renoir, our display code needs to retrieve
the SMU clock and voltage table, however, this operation can fail which
means that we have to check this scenario. Currently, we are not
handling this case properly and as a result, we have seen the following
dmesg log during the boot:
RIP: 0010:rn_clk_mgr_construct+0x129/0x3d0 [amdgpu]
...
Call Trace:
dc_clk_mgr_create+0x16a/0x1b0 [amdgpu]
dc_create+0x231/0x760 [amdgpu]
This commit fixes this issue by checking the return status retrieved
from the clock table before try to populate any bandwidth.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This assert triggers a false negative because there are more than 4 MPCCs
on many asics.
[How]
- change assert comparisson
- remove unused variable
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If plane has changed, dcn20_detect_pipe_changes doesn't update dc_plane_state->update_flags, and the following dcn20_program_pipe can't reprogram hubp correctly.
[How]
Add a new flags bit "plane_changed" in pipe_ctx->update_flags.If old plane isn’t identical to new plane, this bit will be set and guide “dcn20_program_pipe” to programing HUBP correctly.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Changing to smaller modes on OLED panel caused a blue screen crash
as driver reported dram change during vactive when it shouldn't
[how]
Added an extra condition to prevent incorrect dram change timing
Signed-off-by: Naveed Ashfaq <Naveed.Ashfaq@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
use bool directly
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn3 link encoder regs list, so add them.
Also remove
DPCSTX_DEBUG_CONFIG and RDPCSTX_DEBUG_CONFIG as they are unused and
cause compile errors for dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove duplicate semicolons at the end of line.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system enters s3/s0i3, backlight PWM would set user level.
[How]
ABM disable function add keep current gain to avoid it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dongle_type is set during dongle connection but for passive dongles,
dongle_type is not set. If user starts with an active dongle and
then switches to a passive dongle, it will still report as an active
dongle. Trying to emulate the wrong connecter type results in display
not lighting up.
[How]
Set dpcd_caps.dongle_type for passive dongles in detect_dp().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Revert HDCP disable sequence change that blanks stream before
disabling HDCP. PSP and HW teams are currently investigating the
root cause of why HDCP cannot be disabled before stream blank,
which is expected to work without issues.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If DMUB is used, LVTMA VBIOS call can be used to control eDP instead
of tranditional transmitter control. Interface is agreed with VBIOS
for eDP to use this new path to program LVTMA registers.
[How]
Expose DAL interface to send DMUB command for LVTMA control that VBIOS
currently uses.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
core_link_read_dpcd returns only DC_OK(1) and DC_ERROR_UNEXPECTED(-1),
the caller should check error using DC_OK instead of checking against 0
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 32 bit unsigned integer bl_pwm is being shifted using 32 bit arithmetic
and then being assigned to a 64 bit unsigned integer. There is a potential
for a 32 bit overflow so cast bl_pwm to enforce a 64 bit shift operation
to avoid this.
Addresses-Coverity: ("unintentional integer overflow")
Fixes: 3ba0181736 ("drm/amd/display: Move panel_cntl specific register from abm to panel_cntl.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this, enabling dsc will cause a nullptr
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is not defined for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC will be disabled if DPCD 0006F[6:3] is set to a non-zero value
because bits 6:3 are not currently supported. When 6:3 is populated, an
unsupported INCREMENT OF bits_per_pixel value is read (DPCD 0006F[2:0])
[How]
Mask the INCREMENT OF bits_per_pixel field so that values in the
unsupported field are ignored.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming is missing the sequence where for eDP the scrambling is
reset when testing for eye diagram test pattern.
[How]
Include the required register in the definition
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some special panel, it will have an invalid HPD high cause driver
DPCD read/write fail.
[How]
Add extra T3 delay as a monitor patch in dce110_edp_wait_for_hpd_ready
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previously when force enabling DSC on SST display we unknowingly
supressed lane count, which caused DSC to be enabled automatically.
[how]
By adding an additional flag to force enable DSC in dc_dsc.c DSC can
always be enabled with debugfs dsc_clock_en forced to 1
Cc: stable@vger.kernel.org
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current pipe merge and split logic only supports cases where new
dc_state is allocated and relies on dc->current_state to gather
information from previous dc_state.
Calls to validate_bandwidth on UPDATE_TYPE_MED would cause an issue
because there is no new dc_state allocated, and data in
dc->current_state would be overwritten during pipe merge.
[how]
Only allow validate_bandwidth when new dc_state space is created.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
with eDP + DP, each display use one pipe. after DP unplugged, eDP switch
from one pipe to two pipes -- pipe split. dpp1_cm_set_regamma_pwl will
be executed too. The duration from switch single pipe to dual pipes is a
little long which could let eDP enter PSR mode. upon two pipes for eDP
are setup, eDP PHY is disabled. front pipe is not really running to
fetch data from frame buffer. i.e., dchubp is not in normal working
status. execution of hubbub1_wm_change_req_wa may cause p-state warning.
[How]
disable eDP PSR before dc_commit_state. psr is disabled when execute
hubbub1_wm_change_req_wa.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Place the cursor in the center of screen between two pipes then
adjusting the viewport but cursour doesn't update cause DFPstate hang.
[How]
If viewport changed, update cursor as well.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
create a dedicated function to make mst link settings decision, so that
the policy's decision is made in a unified place.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reading for DP alt registers return incorrect values due to LE_SF
definition missing.
[How]
Define correct LE_SF or DP alt registers.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If DMUB is used, LVTMA VBIOS call can be used to control eDP instead of
tranditional transmitter control. Interface is agreed with VBIOS for
eDP to use this new path to program LVTMA registers.
[How]
Create DAL interface to send DMUB command for LVTMA as currently
implemented in VBIOS.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFP_KERNEL may and will sleep, and this is being executed in
a non-preemptible context; this will mess things up since it's
called inbetween DC_FP_START/END, and rescheduling will result
in the DC_FP_END later being called in a different context (or
just crashing if any floating point/vector registers/instructions
are used after the call is resumed in a different context).
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stream disable sequence incorretly destroys HDCP session while stream is
not blanked and while audio is not muted. This sequence causes a flash
of corruption during mode change and an audio click.
[How]
Change sequence to blank stream before destroying HDCP session. Audio will
also be muted by blanking the stream.
Cc: stable@vger.kernel.org
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Using FRAME_UPDATE will result in infopacket to be potentially updated
one frame late.
In commit stream scenarios for previously active stream, some stale
infopacket data from previous config might be erroneously sent out on
initial frame after stream is re-enabled.
[How]
Switch to using IMMEDIATE_UPDATE mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The format in MPCC should be 444
[How]
do not modify the mpcc black color according to pixel encoding format
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register definitions are asic-specific, so functions that use registers of
a particular asic should be static, to be exposed in asic-specific function
pointer structures.
[How]
- make register-definition-using functions static
- make some functions non-static, for future use
- remove duplicate function definition
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn30_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn21_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn20_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The if statement wasn't indented so it's confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's currently no method to enable multi-stream synchronization from
userspace and we don't check the VSDB bits to know whether or not
specific displays should have the feature enable.
[how]
Add a debugfs entry that controls a new DM debug option,
"force_timing_sync". This debug option will set on any newly created
stream following the change to the debug option.
Expose a new interface from DC that performs the timing sync and a helper
to the "force_timing_sync" debugfs that iterates over the current streams
and modifies the current synchornization state and grouping.
Example usage to force a resync (from an X based desktop):
echo 1 > /sys/kernel/debug/dri/0/amdgpu_dm_force_timing_sync
xset dpms force off && xset dpms force on
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Display goes blank after driver installation.
Aux tuning parameters must be used for 2.x only.
Wrong dc_golden_table offset was used.
[How]
Implement a new enc3_hw_init function without VBIOS constants usage to
be called for 3.x
Calculate dc_golden_table offset using sum of
base dce_info offset and golden table offset
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During SetPathMode and UpdatePlanes, the plane state can be null. We default
to linear swizzle mode when plane state is null. This resulted in bandwidth
validation failing when trying to set 8K60 mode (which previously passed validation
during rebuild timing list).
[How]
Change the default swizzle mode from linear to 4kb_s and update pitch accordingly.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Use dc_is_hdmi_signal to determine signal type.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sink OUI supported cap is not set so driver skips programming it.
[How]
Revert the change the skips OUI programming if the cap is not set
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
use correct logger context
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Test expects that we also read HPD_IRQ_VECTOR when checking for
symbol loss as well lane status.
[How]
Read bytes 0x200-0x205 instead of just 0x202-0x205
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.
[How]
Set flag to force psr to use hw lock mgr.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Each asic can optimize best based on its capabilities
[How]
Optimizing timing for a new pixel clock
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming DCN is explicitly forbidden during idle optimzations allowed
state. Existing implemenation relies on OS/DM, which is not robust. Instead
DC should sequence this.
Note that DC will not re-enter idle optimized state on its own, it is only
responsible for catching out of sequence calls. It is still DM
responsibility to sequence appropriate for optimized power, but this change
removes the requirement for DM to cover the .1% case.
[How]
- elevate updates during idle optimized state to full updates
- disable idle power optimizations prior to programming
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With all DCE6 specific macros, register, masks in place
dce60_resource.c may use them and become independent from DCE8 headers
[How]
(v1) Changelog:
- use DCE6 headers for registers and masks, remove the DC8 headers
- remove 7th Display Controller/Encoder register instances (DCE6 has only 6)
- use DCE6 specific watermark programming registers (DPG_PIPE_ARBITRATION_CONTROL3)
- use DCE6 specific input pixel processing registers shift/mask
- use DCE6 specific transform registers shift/mask
- use DCE6 specific link encoder registers shift/mask
- use DCE6 specific output pixel processing registers shift/mask
- use DCE6 specific audio registers shift/mask
- use DCE6 specific dmcu registers shift/mask
- use DCE6 specific hwseq registers shift/mask
- use DCE6 specific mem input registers shift/mask
(v2) Changelog:
- use DCE6 ad hoc dce60_mem_input_construct() function
- use DCE6 ad hoc dce60_transform_construct() function
(v3) Changelog:
- use DCE6 ad hoc dce60_ipp_construct() function
(v4) Changelog:
- use DCE6 ad hoc dce60_link_encoder_construct() function
(v5) Changelog:
- use DCE6 ad hoc dce60_opp_construct() function
(v6) Changelog:
- use DCE6 ad hoc dce60_audio_create() function
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has CRTC_PREFETCH_EN bit in CRTC_CONTROL register
DCE6 has no CRTC_LEGACY_REQUESTOR_EN bit in CRTC_START_LINE_CONTROL register
DCE6 has no CRTC_CRC_CNTL register
[How]
Modify dce60_timing_generator_enable_advanced_request() function
Add dce60_configure_crc() function and dce60_is_tg_enabled() kept as static
Use dce60_configure_crc() function in dce60_tg_funcs
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
kernel WARNING due to use of .cursor_lock = dce_pipe_control_lock inherited by dce110
[How]
DCE6 set .cursor_lock = dce60_pipe_control_lock
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no bottom_pipe and no Blender HW
DCE6 needs 'blank_target' set to false in order to turn on the display
DCE6 has a specific dce60_pipe_control_lock() fuction that is a no op
[How]
Add DCE6 specific functions with needed private dce60_* dependent fuctions
Comment DCE6 specific CTRC program visibility implementation
Fix a typo in the initial header includes comment 's/DCE8/DCE6/g'
Use dce60_apply_ctx_for_surface() in dce60_hw_sequencer_construct
Use dce60_pipe_control_lock() in dce60_hw_sequencer_construct
v2: add missing return type (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has specific SCL_HORZ_FILTER_INIT_{LUMA_RGB,CHROMA} registers
In DCE6 h_init_luma and h_init_chroma initialization is required
Some DCE6 specific SCL_{HORZ,VERT}_FILTER_CONTROL masks were not listed
[How]
Add the registers and masks in dce_transform.h
Add DCE6 specific struct sclh_ratios_inits in dce_transform.h
Add dce60_calculate_inits() function
Add dce60_program_scl_ratios_inits() function
Fix dce60_transform_set_scaler() function
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no SCL_MODE and no SCL_{HORZ,VERT}_FILTER_INIT registers
DCE6 has no SCL_BOUNDARY_MODE bit in SCL_CONTROL register
DCE6 has Line Buffer programming registers (DC_LB_MEMORY_SPLIT,DC_LB_MEM_SIZE)
DCE6 DATA_FORMAT register has only INTERLEAVE_EN bit
DCE6 has no Out Clamp Control programming registers (OUT_CLAMP_CONTROL_*)
[How]
Add DCE6 specific macros definitions for XFM registers and masks
Add DCE6 specific registers to dce_transform_registers struct
Add DCE6 specific masks to dce_transform_mask struct
DCE6 XFM macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_setup_scaling_configuration() w/o missing Scaling registers/bit programming
Add dce60_transform_set_scaler() using DCE6 Line Buffer programming registers
Add dce60_program_bit_depth_reduction() w/o Out Clamp Control programming
Add dce60_transform_set_pixel_storage_depth() use dce60_program_bit_depth_reduction()
Use dce60_transform_set_scaler() in dce60_transform_funcs
Use dce60_transform_set_pixel_storage_depth() in dce60_transform_funcs
Add DCE6 specific dce60_transform_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no FMT_TRUNCATE_MODE bit in FMT_BIT_DEPTH_CONTROL register
DCE6 has no FMT_CLAMP_COMPONENT_{R,G,B} registers
DCE6 has no FMT_SUBSAMPLING_{MODE,ORDER} bits in FMT_CONTROL register
[How]
Add DCE6 specific macros definitions for OPP registers and masks
DCE6 OPP macros will avoid buiding errors when using DCE6 headers
Add dce60_set_truncation() w/o FMT_TRUNCATE_MODE bit programming
Add dce60_opp_set_clamping() w/o Format Clamp Component programming
Add dce60_opp_program_fmt() w/o Format Subsampling bits programming
Add dce60_opp_program_bit_depth_reduction() with dce60_set_truncation
Use dce60_opp_program_fmt() in dce60_opp_funcs
Use dce60_opp_program_bit_depth_reduction() in dce60_opp_funcs
Add DCE6 specific dce60_opp_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has DPG_PIPE_ARBITRATION_CONTROL3 register for Line Buffer watermark selection
DCE6 has STUTTER_EXIT_SELF_REFRESH_WATERMARK_MASK mask for Stutter watermark selection
DCE6 has NB_PSTATE_CHANGE_WATERMARK_MASK mask for North Bridge watermark selection
DCE6 has no GRPH_MICRO_TILE_MODE mask
DCE6 has no HW_ROTATION register
[How]
Add DCE6 specific macros definitions for MI registers and masks
Add DCE6 specific registers to dce_mem_input_registers struct
Add DCE6 specific masks to dce_mem_input_masks struct
DCE6 MI macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_program_urgency_watermark() function
Add dce60_program_nbp_watermark() function
Add dce60_program_stutter_watermark() function
Add dce60_mi_program_display_marks() function w/ new DCE6 watermark programming
Add DCE6 specific tiling programming and modify DCE8 case
Add dce60_program_size() fuction w/o Rotation processing
Add dce60_mi_program_surface_config() fuction
Use dce60_mi_program_display_marks() in dce60_mi_funcs
Use dce60_mi_program_surface_config() in dce60_mi_funcs
Add DCE6 specific dce60_mem_input_construct
v2: remove unused variable (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no DP_DPHY_SCRAM_CNTL register
[How]
Add DCE6 specific macros definitions for LE registers
DCE6 LE macros will avoid buiding errors when using DCE6 headers
Add dce60_set_dp_phy_pattern_hbr2_compliance_cp2520_2() w/o Scramble Control programming
Add dce60_set_dp_phy_pattern_passthrough_mode() w/o Scramble Control programming
Add dce60_configure_encoder() w/o Scramble Control programming
Add dce60_link_encoder_enable_dp_output() w/ dce60_configure_encoder
Add dce60_link_encoder_enable_dp_mst_output() w/ dce60_configure_encoder
Add dce60_link_encoder_dp_set_phy_pattern() w/ dce60_set_dp_phy_pattern_passthrough_mode
Use dce60_link_encoder_enable_dp_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_enable_dp_mst_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_dp_set_phy_pattern() in dce60_lnk_enc_funcs
Add DCE6 specific dce60_link_encoder_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 does not have CURSOR2_DEGAMMA_MODE bit in DEGAMMA_CONTROL register
[How]
Add DCE6 specific macros definitions for IPP masks
DCE6 IPP macros will avoid buiding errors when using DCE6 headers
Add dce60_ipp_set_degamma() function w/o Cursor2 Degamma programming
Use dce60_ipp_set_degamma() in ipp_funcs dce60_ipp_funcs
Add DCE6 specific dce60_ipp_construct
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no BLND_CONTROL register for Blender HW programming
DCE6 has no BLND_V_UPDATE_LOCK register for Pipe Locking
[How]
Add DCE6 specific macros definitions for HWSEQ registers and masks
DCE6 HWSEQ macros will avoid buiding errors when using DCE6 headers
Add dce60_pipe_control_lock() stub with no op
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no SMU_INTERRUPT_CONTROL register, but it's used for DCN10 and later
[How]
Add DCE6 specific macros definitions for DMCU registers and masks
DCE6 DMCU macros will avoid buiding errors when using DCE6 headers
There is no other change needed in dce_dcmu
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 has no DCCG_AUDIO_DTO2_USE_512FBR_DTO mask in DCCG_AUDIO_DTO_SOURCE register
[How]
Add DCE6 specific macros definitions for AUD masks
DCE6 AUD macros will avoid buiding errors when using DCE6 headers
Add dce60_aud_wall_dto_setup() w/o 512*Fs programming
Use dce60_aud_wall_dto_setup() in dce60_funcs
Add DCE specific dce60_audio_create
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Issue in the Mouse cursor size in Linux Desktop Environments
[How]
In DCE6 dc->caps.max_cursor_size need to be set as 64 instead of 128
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Changelog
[Why]
After commit c69dd2d "drm/amd/display: Refactor clk_mgr functions"
dc/clk_mgr requires these changes to add SI parts support
Necessary to avoid hitting default: ASSERT(0); /* Unknown Asic */
that would cause kernel freeze
[How]
Add case statement for FAMILY_SI chipsets
(v2) Changelog
[Why]
DCE6 has no DPREFCLK_CNTL register
[How]
Add DCE6 specific macros definitions for CLK registers and masks
Add DCE6 specific dce60/dce60_clk_mgr.c for DCE6 customization
Code style: reuse all the public functions in dce100/dce_clk_mgr.h header
Code style: use dce60_* static functions as per other DCE implementations
Add dce60_get_dp_ref_freq_khz() w/o using DPREFCLK_CNTL register
Use dce60_get_dp_ref_freq_khz() function in dce60_funcs
Add DCE6 specific dce60_clk_mgr_construct
dc/clk_mgr/dce_clk_mgr.c: use dce60_clk_mgr_construct for FAMILY_SI chipsets
Add Makefile rules for dce60_clk_mgr.o target conditional to CONFIG_DRM_AMD_DC_SI
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
irq service requires changes for DCE6 support
[How]
(v1) DCE6 targets are added replicating existing DCE8 implementation.
due to missing CRTC_VERTICAL_INTERRUPT0_CONTROL registers/masks,
dce/dce_8_0_{d,sh_mask}.h used instead of dce/dce_6_0_{d,sh_mask}.h
(v2) DCE6 headers used adding the necessary vblank irq registers
(INT_MASK and VBLANK_STATUS) and vblank irq masks as implemented
in amdgpu driver.
Add vblank_irq_info_funcs_dce60 with .set and .ack as per commit
b10d51f ("drm/amd/display: Add interrupt entries for VBLANK isr.")
and use it in vblank_int_entry(reg_num) macro definition
(v3) updated due to following kernel 5.3 commit:
4fc4dca ("drm/amd: drop use of drmp.h in os_types.h")
(v4) updated due to following kernel 5.6 commit:
d9e3267 ("drm/amd/display: cleanup of construct and destruct funcs")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hw_factory.c requires changes for DCE6 support
[How]
DCE6 targets added replicating and adapting existing DCE8 implementation.
(v2) changes due to following commit:
91db931 ("drm/amd/display: refactor gpio to allocate hw_container in constructor")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
command_table_helper.c requires changes for DCE6 support
[How]
DCE6 targets added replicating and adapting the existing DCE8 implementation.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
resource_parse_asic_id() and dc_create_resource_pool() are missing SI/DCE6 cases
[How]
SI/DCE6 cases support added using existing DCE8 implementation as a reference
(v2) updated due to following kernel 5.2 commit:
d9673c9 ("drm/amd/display: Pass init_data into DCN resource creation")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCE6 chipsets have a lot in common with DCE8, let's start from this
[How]
DCE6 targets are added replicating existing DCE8 implementation.
NOTE: dce_8_0_{d,sh_mask}.h headers used instead of dce_6_0_{d,sh_mask}.h
initial build prototype due to missing DCE6 macros/registers/masks
DCE6 specific macros/registers/masks will be added with later commits
(v2b) removed dce_version cases in dc/dce/dce_clock_source.c and
updated dce60 due to following kernel 5.0 commits:
24f7dd7 ("drm/amd/display: move pplib/smu notification to dccg block")
9566b67 ("drm/amd/display: remove safe_to_lower flag from dc, use 2 functions instead")
4244381 ("drm/amd/display: clean up base dccg struct")
4c5e8b5 ("drm/amd/display: split dccg clock manager into asic folders")
84e7fc0 ("drm/amd/display: rename dccg to clk_mgr")
77f6916 ("drm/amd/display: Remove duplicate header")
9f7ddbe ("drm/amd/display: fix optimize_bandwidth func pointer for dce80")
4ece61a ("drm/amd/display: set clocks to 0 on suspend on dce80")
(v3b) updated dce60 due to following kernel 5.1 commits:
380604e ("drm/amd/display: Use 100 Hz precision for pipe pixel clocks")
32e6136 ("drm/amd/display: Fix 64-bit division for 32-bit builds")
1877ccf ("drm/amd/display: Change from aux_engine to dce_aux")
c69dffa ("drm/amd/display: fix eDP fast bootup for pre-raven asic")
(v4b) updated dce60 due to following kernel 5.2 commits:
e5c4197 ("drm/amd/display: Add plane capabilities to dc_caps")
813d20d ("drm/amd/display: Fix multi-thread writing to 1 state")
ea36ad3 ("drm/amd/display: expand plane caps to include fp16 and scaling capability")
afcd526 ("drm/amd/display: Add fast_validate parameter")
(v5b) updated dce60 due to following kernel 5.3 commits:
e7e10c4 ("drm/amd/display: stop external access to internal optc sync params")
78cc70b ("drm/amd/display: Engine-specific encoder allocation")
dc88b4a ("drm/amd/display: make clk mgr soc specific")
4fc4dca ("drm/amd: drop use of drmp.h in os_types.h")
(v6b) updated dce60 due to following kernel 5.4 commits:
54a9bcb ("drm/amd/display: Fix a typo - dce_aduio_mask --> dce_audio_mask")
9adc805 ("drm/amd/display: make firmware info only load once during dc_bios create")
(v7b) updated dce60 due to following kernel 5.5 commits:
cabe144 ("drm/amd/display: memory leak")
8276dd8 ("drm/amd/display: update register field access mechanism")
f6040a4 ("drm/amd/display: configurable aux timeout support")
bf7f5ac ("drm/amd/display: map TRANSMITTER_UNIPHY_x to LINK_REGS_x")
(v8b) updated dce60 due to following kernel 5.6 commits:
d9e3267 ("drm/amd/display: cleanup of construct and destruct funcs")
f42ea55 ("drm/amd/display: add separate of private hwss functions")
(v9b) updated dce60 due to following kernel 5.8 commits:
bba8289 ("drm/amd/display: code clean up in dce80_hw_sequencer.c")
904fb6e ("drm/amd/display: move panel power seq to new panel struct")
d4caa72 ("drm/amd/display: change from panel to panel cntl")
(v10) Fix up PLL handling for DCE6:
DCE6.0 supports 2 PLLs. DCE6.1 supports 3 PLLs. (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use DCN21 functions instead of DCE110
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some monitors could suffer symbol unlock but cannot send HPD IRQ to
notic source device to handle link loss. This makes monitor stuck in
abnormal status and causes black screen.
[How]
According to the suggestion from scalar vendor, to check lane status
again after link training done. That can improve the comaptibility
from current production monitors.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dcn3_update_clocks there are situations where dppclk is not
lowered (i.e. stays the same), but DTO still needs to be increased
before we program pipe frontend (i.e. in prepare_bandwidth). If we
don't program the new DTO value before we program the pipe,
we will underflow as soon as the pipe lock is released until the
next call to dcn3_update_clocks where the DTO is updated.
[How]
Remove dppclk check before programming new DTO value.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change replaces older looping code in favor of these functions.
[How]
There are built in functions for extracting global sync params
during mode validation now.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix below warnings reported by coccicheck:
./drivers/gpu/drm/amd/display/dc/clk_mgr/dcn30/dcn30_clk_mgr.c:557:2-7: WARNING: NULL check before some freeing functions is not needed.
Fixes: 4d55b0dd1c ("drm/amd/display: Add DCN3 CLK_MGR")
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement an interface to obtain plane size caps
[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On DCN20, Some features would not be activated when ALLM was turned on.
TV seemed to activate only the latest info packet sent, and the ALLM
info packet was sent after the VSIF info packet.
The packet indices was also inconsistent between DCN10 and DCN20.
[how]
Change the packet indices of DCN20 to match those of DCN10.
This makes them consistent and also makes the vendor info packet
be sent after the hfvsif info packet.
Signed-off-by: Naveed Ashfaq <Naveed.Ashfaq@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_add_dsc_to_stream_resource is accessed in amdgpu_dm directly.
This creates build error for configuration with DCN disabled.
[How]
Make the function available through a resource pool function so
that dcn20 function need not be called directly.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The capability fields are reserved for DSC branch
only to report the capability related to the
branch's DSC decoder.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support V3
[How]
Generate new VSIF for V3
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to add new parameters to debugfs logging so
we will know what parameters DSC is using for
debug purposes. So we are adding a read function
in debugfs to read DSC status registers
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scaler vendor confirmed the 5ms was not helpful so no point in keeping
it.
[How]
Revert 5ms delay after setting training pattern.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "stream" pointer can't be NULL and it's dereferenced on the line
before so the check doesn't make sense.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling the debugfs for CRC capture we hit assertions caused by
register address and field masks and shifts missing.
[How]
We want these registers programmed, so add in the SRI/SF entries for
this register.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failing to allocate a transfer function during stream construction leads
to a null pointer dereference
[How]
Handle the failed allocation by failing the stream construction
Cc: stable@vger.kernel.org
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our validation is a known mess with actual validation mixed with
topology configuration. This change makes sure topolgical validation is
completed before any topology changes are made so we do not run into
issues where we merge and split a pipe over the course of a single call.
v2: Squash in compilation fix
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.
before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.
[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when ppt disabled, the watermark doesn't get fine tune causing
underflow.
[How]
It is a temporary solution to reduce sr_xxx_time by 3 us when ppt
disable.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN3 has two gamut remap matrices. When using CSC adjustment the CM
remap is set to bypass and MPCC remap is used. However to bypass CM
some state in the context is modified and not restored correctly
resulting in subsequent calls to disable MPCC remap as well.
[How]
Fix logic for save/restore of remap enable flag when programming MPCC
remap matrix.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Soft hangs occur when FreeSync is engaged since we utilize VUPDATE
(which doesn't fire when holding the pipe lock) to send back vblank
events when FreeSync is active.
[How]
The alternative (working) interrupt source for this mechanism is
VUPDATE_NO_LOCK. We already use this all other DCN revisions so align
dcn30 with those as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is missing for dcn3 so add it from dcn20.
enc2_set_dynamic_metadata() trys to sets this and we get a
generic_reg warning since the mask is not defined.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to be able to see SMU messages sent and their responses
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we don't explicitly send a request for a minimum PHYCLK, and
we hope that the dependencies other clocks have will raise PHYCLK when
needed.
[How]
- new clk_mgr function to keep track of PHYCLK requirements
- request maximum requirement across all links
- remove PHYCLK from clock state comparator, as it doesn't come from DML
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver re-initialize registers already set in FW
[How]
Transfer init to FW
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print scaling parameters as they are calculated in diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changes that are fast don't require updating DLG parameters making
this call unnecessary. Considering this is an expensive call it should
not be done on every flip.
DML touches clocks, p-state support, DLG params and a few other DC
internal flags and these aren't expected during fast. A hang has been
reported with this change when called on every flip which suggests that
modifying these fields is not recommended behavior on fast updates.
[How]
Guard the validation to only happen if update type isn't FAST.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1191
Fixes: a24eaa5c51 ("drm/amd/display: Revalidate bandwidth before commiting DC updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of certain display configurations we want to allow max detile
buffer utilization by using 4 to 1 mpc combine
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register key for AE or QA do regression test. New edid status for
check.
[How]
Add register key edid_read_retry_times.
Add new edid status EDID_FALL_BACK.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For special DP convert VGA dongle, core_link_read_dpcd for
DP_DOWNSTREAM_PORT_0 always return fail, then dongle_type will be set to
DISPLAY_DONGLE_NONE, which will cause desktop resolution abnormal.
[How]
If dpcd for DP_DOWNSTREAM_PORT_0 read fail, skip set dongle_type =
DISPLAY_DONGLE_NONE.
Signed-off-by: jinlong zhang <jinlong.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU may return error code to driver, but driver only check if response
is OK.
[How]
Check SMU response instead of reg_wait, assert in case of reponse isn't
OK.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to keep the same buffer allocated for use during multiple
hardware initializations.
[How]
- allocate gpu memory buffer on clock manager construct
- free gpu memory buffer on clock manager destruct
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debug flags are not set by default.
[How]
Set debug flags to 0
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Two issues:
1. Add read only operation support for query ddc data over aux.
2. Fix a bug where if read size is multiple of 16,
mot of the last read transaction will not be set to 0.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the front porch of the two timings differ, then there may not be
enough time while both streams are in vertical blank to perform a memory
clock change. This can hang the system.
[How]
Check the each streams timing.v_front_porch when determining if the two
streams are synchronizable.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
seamless boots requires split of init_hw into hw and pipes to work. This
was implemented in dcn10_init_hw but did not apply yet to dcn30.
how:
Copy over dcn10_init_hw and adapt it to dcn30 using recent changes to
dcn3. Behavior will be different in init sequence.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We try to to change new_clocks->dppclk_khz to 100000 when
new_clocks->dppclk_khz is 0
[How]
Don't change new_clocks->dppclk_khz value when new_clocks->dppclk_khz is
0
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
10K YCbCr420 does not need ODM 4:1, but it requires MPC 4 split
indicated on the flags.
[How]
Make pixel encoding and resolution size specific workaround to enable
ODM combine on YCbCr420 high resolution modes.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If a typeC to HDMI dongle supports YCbCr420 pass through and VSC
colorimetry and pixel encoding formats in the Extended Receiver
Capability, we shall allow VSC SDP to be used.
[How]
The Extended Receiver Capability field shall check the
EXTENDED_RECEIVER_CAPABILITY_FIELD_PRESENT bit in the
TRAINING_AUX_RD_INTERVAL register. Removed DPCD rev checking for VSC
SDP.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All YCbCr420 resolutions 5K and above have tiling and discoloration
issues. The issue can be remedied by forcing ODM combine from 5K to 8K.
10K resolution requires ODM 4:1. The mechanism of what the real problem
is, that is inherent in ODM combine programming, doesn't seem to be
pointed at singular register programming (CLK, MPC, DCSURF, etc.), and
needs more in-depth programming sequence review for these new use case
scenarios. Until then, workaround to enable ODM combine is proposed.
While it is not our policy, HW spreadsheet also recommends turning on
ODM for these scenario to lower the voltage.
[How]
Make pixel encoding and resolution size specific workaround to enable
ODM combine on YCbCr420 high resolution modes.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is using pixelclk AVFS for dppclk, that would cause issue.
[How]
To use dispclk AVFS for both dispclk and dppclk. There would choose
dppclk for request voltage when dispclk wouldn't be updated case. If
dispclk need to be updated, then it'll choose the bigger one from dppclk
and dispclk for request voltage.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Check max_tmds_clk_mhz firstly will restrict pixel clock under HDMI
1.4, thus HDMI2.0 port can't correctly support 4K 60Hz.
[HOW]
Fine tune the logic to check max_forum_tmds_clk_mhz firstly.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Need to check if local_sink is NULL before accessing.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_link_set_psr_allow_active() always returns true, even in the case
that PSR is not supported.
[How]
Hook up the return value of dc_link_set_psr_allow_active().
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Side-by-side and Top-and-bottom stereo configurations fail DML mode
validation due to Viewport exceeded.
This is because we consider the planes as being pipe split in pipe
population so we end up doubling the viewport width, eg. from 4k to 8k.
[How]
These pipes technically aren't hsplit, so add a check for determining
whether is_hsplit should be set.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
assr is content protection for eDP, in order to use it we need to call
psp ta (dtm)
[How]
We have a enable_assr callback, hook into this and call the correct psp
cmd id to enable assr.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DC doesn't check requested pixel clock against an EDID
specified TMDS max clock if it exists, passing modes that should fail
[HOW]
Add max TMDS clk to edid caps and perform check during validation
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc->hwss->edp_backlight_control is null, it would casue it only be off
main-link of eDP. It is not worng behavior for eDP power sequence off.
[how]
Must use hwseq->funcs.edp_backlight_control finction pointer for edp
backlight.
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hw lock manager adds the ability to lock pipe, cursor, and dig in fw.
[How]
Send hw lock command to fw to lock pipe, cursor, and dig.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update each p-state in the bounding box
[How]
Update states when assigning values to clocks
v2: squash in patch to set min values (Alex)
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Used sparse(make C=1) to find these loose ends.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to update the bounding box to have more granular control of the
DCFCLK.
[How]
Setup DCFCLK to use STA values and also optimal values based on
UCLK.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get the values from VBIOS table
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dmub FW running abnormal after resume from S0i3 due
to data aliagnment issue.
[How]
Before having a solution for this issue, temparory
not doing data pack.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some special timing with border, like DMT 640*480 72Hz,
pipe split can't handle well. Thus, it will be black screen
for these special timing.
[How]
Disable pipe split for these timing with borders as W/A.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC is very fast at link training and stream enablement
which causes issues such as blackscreens for non-compliant
monitors.
[How]
After debugging with scaler vendors we implement the
minimum delays at the necessary locations to ensure
the monitor does not hang. Delays are generic due to
lack of IEEE OUI information on the failing displays.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DMUB command table should be allowed to be used
only if dmcu is explicitly disabled.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To allow code reuse with minimal duplication watermark
calculation needs to be function pointer.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the debugging process related to a hot-plug
problem with 4k display, we realized that we had
some issues related to the global state validation.
This problem was not explicitly highlighted in the
dmesg log, for this reason, this commit adds a function
that converts `enum dc_status` to a human-readable
string and appends the proper warning message in case
of failure.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Dummy pstate latency actually varies between different
UCLK frequencies, when calculating watermark C, if DAL
always assumes worst case, then it can lead to dummy
pstate not supported scenarios.
[how]
Rather than statically calculating dummy pstate using
worst case, we store the entire table of UCLK to dummy
pstate relationships. On a per mode basis, we calculate
the actual UCLK lower limit, and use the dynamic worst
case dummy pstate latency. This prevents the situation
where we don't support full p-state (which will force
high DPM), but still use low DPM dummy pstate latency.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.
[how]
This reverts commit fb8cf277b1.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were updating mpcc if there were tree changes which
is unnecessary since any mpcc being added or removed
will automatically update the tree.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The SDP deadline indicate the vertical time to send CRC
infopacket in PSR.
Signed-off-by: po-tchen <po-ting.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sprcified monitor scalar cannot recognize timing
change on demand. Once the link phy disable and enable
during a short period then the Sink protection mechanism
could keep the screen in blank and cannot be recoverred.
[How]
To add 100ms delay between enable link phy and link training.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for audio on real TV issue.
[how]
-add wall clock programming for DPREF based when
Pixel clock is done by DP DTO.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML failures occur for 420 modes with dynamic pipe
splitting enabled because the ChromaViewport exceeds
the ChromaSurfaceWidth.
This is caused by adding the viewport_width instead
of the viewport_width_c.
This similarly occurs for rotated modes due to the
use of viewport_height instead of viewport_height_c.
[How]
Correct the calculations.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commmit fd0293dd5b.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SOC_BOUNDING_BOX_VALID is unused and not required for dcn21.
[How]
Remove it.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC calculations fail because the u16 bits_per_pixel from
the DRM struct is being casted to the u8 drm_bpp parameters
and locals. Integer wraparound is happening because this
value is greater than 255.
[How]
Use u16 to match what's in the structure instead of u8.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Typos cause bandwidth calculation errors, one
of which can cause infinite loop on dcn1 with eDP
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we want to use float point operation on Linux
we need to use within special kernel protection
(`kernel_fpu_{begin,end}()`.), otherwise the kernel
can clobber userspace FPU register state. For detecting
these issues we use a tool named objtool (with -Ffa
flags) to highlight the FPU problems, all warnings can
be summed up as follows:
./tools/objtool/objtool check -Ffa
drivers/gpu/drm/amd/display/dc/dml/dml_common_defs.o
[..] dc/dsc/rc_calc.o: warning: objtool: get_qp_set()+0x2f8:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: dsc_roundf()+0x5:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: dsc_ceil()+0x5:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: get_ofs_set()+0x3eb:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc.o: warning: objtool: calc_rc_params()+0x3c:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/dc_dsc.o: warning: objtool:
get_dsc_bandwidth_range.isra.0()+0x8d:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/dc_dsc.o: warning: objtool: setup_dsc_config()+0x2ef:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc_dpi.o: warning: objtool:copy_pps_fields()+0xbb:
FPU instruction outside of kernel_fpu_{begin,end}()
[..] dc/dsc/rc_calc_dpi.o: warning: objtool:
dscc_compute_dsc_parameters()+0x7b:
FPU instruction outside of kernel_fpu_{begin,end}()
This commit fixes the above issues by rework DSC as described:
1. Isolate all FPU operations in a single file;
2. Use FPU flags only in the file that handles FPU operations;
3. Isolate all functions that require float point operation in static
functions;
4. Add a mid-layer function that does not use any float point operation,
and that could be safely invoked in other parts of the code.
5. Keep float point operation under DC_FP_{START/END} macro.
CC: Christian König <christian.koenig@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Tony Cheng <tony.cheng@amd.com>
CC: Harry Wentland <hwentlan@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for following new format, no alpha
SURFACE_PIXEL_FORMAT_GRPH_RGB111110_FLOAT/_FIX:
SURFACE_PIXEL_FORMAT_GRPH_BGR101111_FLOAT/_FIX
same as case SURFACE_PIXEL_FORMAT_GRPH_ARGB1555:
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These lines are a part of the if statement and they are supposed to
be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There're 2 .dsc_pg_control, drop the first one.
.dsc_pg_control = NULL,
.dsc_pg_control = dcn20_dsc_pg_control,
Signed-off-by: Flora Cui <flora.cui@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct gpu_info_voltage_scaling_v1_0 & gpu_info_soc_bounding_box_v1_0 is
defined in amdgpu_socbb.h
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a dml_print message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We may end up with no planes set yet, depending on the ordering, but we
should have the proper blanking state which is either handled by either
DPG or TG depending on the hardware generation. Check both to determine
the proper blanked state.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/781
Fixes: 5fc0cbfad4 ("drm/amd/display: determine if a pipe is synced by plane state")
Cc: nicholas.kazlauskas@amd.com
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever we switch between tiled formats without also switching pixel
formats or doing anything else that recreates the DC plane state we
can run into underflow or hangs since we're not updating the
DML parameters before committing to the hardware.
[How]
If the update type is FULL then call validate_bandwidth again to update
the DML parmeters before committing the state.
This is basically just a workaround and protective measure against
update types being added DC where we could run into this issue in
the future.
We can only fully validate the state in advance before applying it to
the hardware if we recreate all the plane and stream states since
we can't modify what's currently in use.
The next step is to update DM to ensure that we're creating the plane
and stream states for whatever could potentially be a full update in
DC to pre-emptively recreate the state for DC global validation.
The workaround can stay until this has been fixed in DM.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To match previous behavior and to not hang the kernel if someone
accidentally builds with KGDB enabled.
Fixes: 1aad707819 ("drm/amd/display: Make BREAK_TO_DEBUGGER() a debug print")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to guard some new DCN3.0 stuff.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was done already done for other DCN blocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initilize function tables for hw programing
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Video Package generator.
used to prepare avi info, DP info etc
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Audio formating
Audio related code for setup/control
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-Handle DCN3 cases for bios parser and command tables
-Add command function tables for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for managing resources for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program GPIO HW block
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add IWQ services for DCN3,
This allows us to create/init and manage irqs for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for DML(Display mode library) for bandwidth calculations
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 HUBP (Display to data fabric interface
pipe)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 MPC (Multiple pipe and plane combine)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 OPP (Output Plane Processing)
HW Blocks:
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN3 block
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When determining synchronzied vblank we don't need to compare the stream
with itself
[How]
If comparing same stream, continue to next iteration
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We hit an issue which driver reallocate a pipe from desktop bottom
pipe to video bottom pipe. In this case, driver need to re-enable
plane.
[how]
Enable plane if container of plane status changed.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics DIO test with eDP not connected is required to run
[How]
Allow Diagnostics test with eDP not connected to skip link detection but
still execute DIO test
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unit enter to S4, garbage show on screen when do OPTC blank.
[How]
Wait for vblank then do OPTC blank
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are scenarios where no OPP is assigned to an OTG so its value is
0xF which is outside the size of the OPP array causing a potential
driver crash.
[How]
Change the assert to an early return to guard against access. If
there's no OPP assigned already, then OTG will be blank anyways so no
functionality should be lost.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link loss currently only retrains and re-enables the stream. This can
cause issues for some sinks.
[How]
When link loss occurs, the link and stream(s) should be completely
disabled and then reenabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation is slightly inaccurate and will often
result in truncation/floor operation decrementing an exact
integer output by 1.
Only rounded down output is ever expected, just extract the fp
exponent for this to increase performance and avoid any
truncation issues.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously we used link signal type to get the caps. We should use the
sink signal type
[How]
Use sink signal type instead of link signal type
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link_status is incorrect cause driver power off eDP when backlight
on. Some eDP panels may show garbage on screen.
[How]
Correct link_status when power off encoder
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Warnings in the kernel are generally treated as errors.
The BREAK_TO_DEBUGGER macro is not a critical error or warning, but
rather intended for developer use to help investigate behavior and
sequences for other issues.
We do still make use of DC_ERROR/ASSERT(0) in various places in the
code for things that are genuine issues.
Since most developers don't actually KGDB while debugging the kernel
these essentially would have no value on their own since the KGDB
breakpoint wouldn't trigger - ASSERT(0) was used as a shortcut to get
a stacktrace.
[How]
Turn it into a DRM_DEBUG_DRIVER print instead. We unfortunately lose
the stacktrace, but we still do retain some of the useful debug
information this offers by having at least the function and line
number loggable.
If KGDB is supported in the kernel this will still trigger a real
breakpoint as well.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.
[How]
Removed wa from dal side.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the correct value to immediate flip required field.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change removes internal rounding in dml_log2 function.
Dml_log2 is expected to return a float output. In case an int is needed
dml will floor the output on it's own.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we're copying the entire bios image into vbios. Loading time
for FW with entire bios(54272 bytes) is 105138us. By copying only the
sections of bios we're using(4436 bytes), loading time drops to 104326us
which saves us 812us.
[HOW]
ROM header, master data table, and all data tables will be packed in
contiguous manner. The offsets for the data tables are remapped to their
newly packed location.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.
[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And only set to 400us if LTTPR is not present.
Before this piece of logic is interwined with LTTPR support.
Now we will default to 3.2ms aux timeout even if LTTPR support is not
enabled by driver.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Failing validation when building scaling parameters causes corruption to
occur due to pipe splitting with smaller pixel widths than HW supports.
This needs to fail silently for now to hide the corruption until the
corruption itself can be fixed.
[HOW]
Do not fail validation if building scaling params fails.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove dm_write_persistent_data and dm_read_persistent_data as
persistence should be handled in DM.
[How]
Remove functions. Move read/write calls into DM layer while maintaining
logic.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When disconnect fe from be, something such as unstable clock may cause
garbage occurs.
[How]
Send set avmute at the beginning of disable stream and send reset avmute
at the end of enable stream.
Signed-off-by: Jinze Xu <jinze.xu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Save the correct num vmid during resource creation and fix RN gpuvm
level from 1 to 16 vmid entries.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The minimum plane size we can support in DML is 16x16. If we try to pass
a 16x16 plane with dynamic pipe split then validation will fail since it
tries to split it into two pipes, each 8x8.
Some userspace doesn't check that the commit fails and because the
commit fails the old state is retained, resulting in corruption.
[How]
Add a workaround to avoid pipe split if any plane is 16x16 or smaller.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP training sequence to set SCRAMBLING_DISABLE bit properly based on
training pattern - per DP Spec.
[How]
Update dpcd_pattern.v1_4.SCRAMBLING_DISABLE with 1 for TPS1, TPS2, TPS3,
but not for TPS4.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the rework for removing the FPU issues, I found the following
warning:
[..] dml_common_defs.o: warning: objtool: dml_round()+0x9: FPU
instruction outside of kernel_fpu_{begin,end}()
This file has a single function that does not need to be in a specific
file. This commit drop dml_common_defs file, and move dml_round function
to dml_inline_defs.
CC: Christian König <christian.koenig@amd.com>
CC: Alexander Deucher <Alexander.Deucher@amd.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Tony Cheng <tony.cheng@amd.com>
CC: Harry Wentland <hwentlan@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current odm/mpc combine logic to detect which pipes need to split
logically is flawed leading to incorrect pipe merge/split operations
being taken.
This change cleans up the logic and fixes the logical errors.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Assigning a different DSC resource than the one previosly used is
currently not handled. This causes black screen on mode change when more
than one monitor is connected on some ASICs.
[how]
- Acquire the previously used DSC if available
- Make sure re-program is triggered if new DSC is used
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing on a Polaris11 gpu with DCE-11.2 suggests that it
seems to work fine there, so optimistically enable it for
DCE-11 and later.
v2: drop DCE 11.0 hunk. Carrizo (DCE 11.0) has a HW bug where FP16
scaling doesn't work. The upscale and downscale factors were
intended to block those FP16 cases and reject the commit but
nobody ever added those to atomic check. Once those are added
to atomic check, this can be re-enabled.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
One call was forcing stutter on instead of looking at the debug option.
Ensure we always check the debug option unless we want to force stutter
off.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl6ztuYACgkQaA3BHVML
eiMWaAgAvYpXvBqBfE/5jOTa1zWQUX9VMbmMDUqSAgec5r/HVHjmlbsDWkLff2XG
rH7T2shMNJwluoCleHfRFYUfyUWMmXoMgri1elnf4EgddmekLZ6vNQjtAYMRFUfL
7VegcFw5D5Z28uxK5YGnaaSQob34LvD8UTgvnCVfDQzCjcEzGYi1d9XELm7kTHje
dF2FOWPeF8FTqP0XHM8RrHNXW/pUPy9qErpmb2bWYBQp7ebkI2Q4p6IZIpRQm757
bnKPIdMEcy4BWMk1xtzjEYEb4bGSZhozJUWKFwpm/AHNvTrQCt9hn0GSVrXiqBcR
UKb42BRxEVR29C/4n10pUcnnQmmi+Q==
=yzZ9
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-05-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.8:
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507072503.GA10979@linux-uq9g
Remove duplicate headers which are included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_resource.c:3216:16-22:
Unneeded variable: "result". Return "DC_OK" on line 3229
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make a separation of what belongs in the differen dmub
headers
dmub_srv.h is for exposing dmub srv interface to rest of
driver.
other headers inside dmub/inc exposes cmds and definitions
that are owned by the firmware
[How]
keep firmware owned definitions in dmub/inc
move stuff that is purely driver interface headers to dmub/
since those are interface calls that are defined for rest of
driver to use
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Want to make use of detile buffer of all 4 pipes to maximize amount of
data stored to hide certain memory latency cases.
[How]
In case of 1 plane and 1 stream, program 4 pipes to each retrieve 1/4 of
plane later mixed together by the MPCs. Added support for transition
from 4 to 1 MPC to 2 to 1 MPC or no pipe split case and vice versa.
Currently, only enabled if debug flag is set.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
same with CL#1711022(correcting yuv420 black color in function dcn10_blank_pixel_data,program_scaler),
yuv420 black color also needs to be correct when enabling HDMI stream at the resume procedure.
[How]
correcting the yuv420 black color according to the way how 420 is packed :2 channels carry Y component,
1 channel alternate between Cb and Cr.
Signed-off-by: yanyan kang <Yanyan.Kang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For a type like PSR version, it makes sense for most of the code
to include a dc type, instead of having this a fw type define since
this is a capability and type exposed by dc.
Especially if it doesn't even need to communicate with the fw.
The code that is packing the firmware command message
should be the one who needs to translate the psr version
into a command that the firmware understands.
[How]
Add a dc_psr_version enum.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in Is_Support function, driver report different caps between
same timing but different scaling cause OS inconsistent.
[How]
min_row_time is a local that’s only used for verifying immediate
flip support. Clamp the vratio used for its calculation to 1.0.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain display configurations we want to allow PSTATE
switch when one display can switch in VACTIVE and the
other display can switch in VBLANK
[How]
Add extra condition to dcn2 pstate support check
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wait counter is not being reset for each pipe.
[How]
Move counter reset into pipe loop scope.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
What a mode change is requested for the same timing a full stream reset
can occur in some cases which causes monitor to blank for a few seconds.
[How]
Do not consider infoframe updates as needing a full stream reset as they
will be handled on the first flip after a modeset when surface
information is available.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
There is a problem in hscale_pixel_rate, the bug
causes DCN to be more optimistic (more likely to underflow)
in upscale cases during prefetch.
This commit ports the fix from DV code to address these issues.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel_cntl specific register should be access in panel_cntl object.
[How]
Move these register access from abm to panel_cntl.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.c:1277:11: warning: variable ‘speakers’ set but not used [-Wunused-but-set-variable]
It is introduced by commit 0c41891c81 ("drm/amd/display:
Refactor stream encoder for HW review"), but never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dce/dce_stream_encoder.c:1339:11: warning: variable ‘speakers’ set but not used [-Wunused-but-set-variable]
It is introduced by commit 4562236b3b ("drm/amd/dc:
Add dc display driver (v2)"), but never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_dpp.c:137:11: warning: variable ‘pixel_width’ set but not used [-Wunused-but-set-variable]
It is introduced by commit 70ccab6040 ("drm/amdgpu/display:
Add core dc support for DCN"), but never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dcn20_validate_bandwidth function would have code touching the
incorrect registers emitted outside of the boundaries of the
DC_FP_START/END macros, at least on ppc64le. Work around the
problem by wrapping the whole function instead.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Once should generally be enough for diagnosing what lead up to it,
repeating it over and over can be pretty annoying.
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c:31:51-52:
exit_optimized_pwr_state: first occurrence line 86, second occurrence
line 92
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c:31:51-52:
optimize_pwr_state: first occurrence line 85, second occurrence line 91
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c:31:51-52:
set_cursor_attribute: first occurrence line 71, second occurrence line
89
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c:31:51-52:
set_cursor_position: first occurrence line 70, second occurrence line 88
drivers/gpu/drm/amd/display/dc/dcn21/dcn21_init.c:31:51-52:
set_cursor_sdr_white_level: first occurrence line 72, second occurrence
line 90
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the file drm_dp_helper.h we have a macro named
DP_DSC_THROUGHPUT_MODE_{0,1}_UPSUPPORTED, the correct name should be
DP_DSC_THROUGHPUT_MODE_{0,1}_UNSUPPORTED. This commits adjusts this typo
in the header file and in other places that attempt to access this
macro.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429184142.1867987-1-Rodrigo.Siqueira@amd.com
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add set backlight to hw sequencer, dmu communication will
be handled in hw sequencer for new asics.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging, it can be useful to be able to modify the dummy
p-state latency, this will make it easier to do so.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We read memory that we shouldn't be touching if the struct isn't
a full union dmub_rb_cmd.
[How]
Fix up all the callers and functions that take in the dmub_cmd_header
to use the dmub_rb_cmd instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.
[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes the following scenario:
- Flip has been prepared sometime during the frame, update pending
- Cursor update happens right when VUPDATE would happen
- OPTC lock acquired, VUPDATE is blocked until next frame
- Flip is delayed potentially infinitely
With the igt@kms_cursor_legacy cursor-vs-flip-legacy test we can
observe nearly *13* frames of delay for some flips on Navi.
[How]
Apply the Raven workaround generically. When close enough to VUPDATE
block cursor updates from occurring from the dc_stream_set_cursor_*
helpers.
This could perhaps be a little smarter by checking if there were
pending updates or flips earlier in the frame on the HUBP side before
applying the delay, but this should be fine for now.
This fixes the kms_cursor_legacy test.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Viewport limit was set to 16 pixels due to an issue with MPO
on small viewports. This restriction does not apply and the
viewport limit can now be lowered.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
If building scaling parameters fails, validation
should also fail.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently RN SOC bounding box update assumes we will get at least
2 clock states from SMU. This isn't always true and because of special
casing on first clock state we end up with low disp, dpp, dsc and phy
clocks.
This change removes the special casing allowing the first state to
acquire correct clocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check before programming the register since it isn't present on
all IPs using this code.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some include paths don't need to have relative paths
And some types missing
[How]
make some changes to headers and modify include path
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If mode is not supported, pipe split should not be disabled.
This may cause more modes to fail.
[HOW]
Check for mode support before disabling pipe split.
This commit was previously reverted as it was thought to
have problems, but those issues have been resolved.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The '>' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c:602:28-33: WARNING:
conversion to bool not needed here
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_mpc.c:455:70-75: WARNING:
conversion to bool not needed here
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable option is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there's a bug in the new logic for panel power control. the check is
wrong, and will skip panel power control under the wrong conditions.
[How]
fix to check for NULL panel_cntl
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since ABM resource is mapped to stream res, all the ABM access should
via stream res.
[How]
Get ABM instance from stream res instead of resource pool.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When link loss happened, monitor can not light up if only re-train the
link.
[How]
Blank all the DP streams on this link before re-train the link, and then
unblank the stream
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Organizational Unit Identifier register is optional, and its
presence is published via Down Stream Port Count register.
Writing this register when not available will result in errors
[how]
Read this register and continue writing OUI only if the panel
has the support advertised.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
it doesn't represent panel specifically, it's more like the control
logic for the panel
[How]
change from panel to panel cntl to make it a bit more clear
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HW rotation was enabled in DAL3 but hubp cursor calculations for HW roation
were only added to dcn20.
[How]
Add hubp cursor position calculation changes to dcn10.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We expect to be able to perform immediate flipping without having to
recalculate and update all the watermarks.
There are certain usecases today (1080p @ 90deg, 2160p @ 90deg) such
that we get a urgency value of 0 for frac_urg_bw_flip because we're
explicitly passing in a value of "false" for requiring immediate
flip support into the DLG calculation.
[How]
Always pass in true into the calculation. With this we get a correct
non-zero value for frac_urg_bw_flip.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
without destroy it is causing a memory leak
[How]
destroy panel on link destruct
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver already get display clock from SMU base on MHz, but driver read
again and mutiple 1000 cause wait loop value is overflow.
[How]
remove coding error
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel power sequencer is currently just sitting in hwseq but it really
it tied to internal panels
[How]
make a new panel struct to contain power sequencer code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight adjustment is tied to a specific display. So make the calls
target a link rather than making it a global state.
[How]
make all backlight calls link based
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In certain conditions with low pixel clock, some values in DML may go
past the max due to margining for latency hiding. This causes assertions
to get hit.
[HOW]
If the pixel clock is low and some values are high, cap it to the max.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Driver does not recognize new definitions of psr states.
- Internal tool is required for checking if psr is active.
[How]
- Parse psr state correctly so that driver will recognize psr state.
- Add visual confirmation that psr is active using existing mechanisms.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some cases were incorrectly reporting the wrong visual confirm, even
though they were working as expected.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On ASIC without ABM support (most dGPU) we run into a null pointer
dereference when attempting to set the backlight level.
[How]
This function requires ABM, so fix up the condition to only allow
DMCU to be optional.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to set up stream even with virtual displays when running
diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Some inputs to dml_ceil have it dividied by int which causes a
truncation. This loss of precision means the ceil function becomes
redundant and does not round up.
[How]:
Cast parameter to float before division.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]:
Calculating refcyc_per_meta_chunk_vblank_l when DCC is disabled may lead
to a large number causing an assert to get hit. In VBA, this value is 0
when DCC is disabled.
[HOW]:
Set value to 0 to avoid hitting the assert.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Optc needs to know if timing is enabled with ODM or DSC before computing
crc. Otherwise value computed will be inaccurate. Before this change,
the CRC computed without ODM is not equal to the CRC computed with ODM
for the same timing. This is unexpected as we are driving the same
timing despite of the underlaying hardware setup to achieve it. This is
caused by missing hardware programming sequence to support it.
[how]
Add the new programming sequence based on hardware guide.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some mst dock can't translate DP to HDMI properly.
[How]
Bypass YCbCr timings on specific MST device.
Signed-off-by: Jinze Xu <jinze.xu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As it stands, psr has feature flags in dm, stream, and link. Most are
not defined well enough, and different dm layers have different uses for
these same flags.
[How]
We define a new structure called psr_settings in dc_link that will hold
the following psr feature flags:
psr_feature_enable - psr is supported
psr_allow_active - psr is currently active
psr_version - internal psr version supported
psr_frame_capture_indication_req
psr_sdp_transmit_line_num_deadline
The last two flags were moved out of the power module
for the purposes of consolidating psr flags.
Their use is already well-defined.
Psr caps reported by sink will also be stored in dc_link,
in dpcd_caps.psr_caps.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set backlight calls to firmware are are being prevented by dmcu == null
check. Dmcu is expected to be null in this case.
[How]
Only prevent call if dmcu and abm are null. Also rename variable
'use_smooth_brightness' to 'fw_set_brightness' as it's more appropriate.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HUBBUB watermark registers are in an area that cannot be power
gated, but the HUBP copies of the watermark values are in areas that can
be power gated. When we power on a pipe, it will not automatically take
the HUBBUB values, we need to force propagation by writing to a
watermark register.
[How]
- new HUBBUB function to re-write current value in a WM register
- touch WM register after enabling the plane in program_pipe
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dmcu init fw call has some logic to initialize abm values. Since this
doesn't exist on dmcub, must find a proper place for it in the abm
sequence.
[How]
Move enable fractional pwm call.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Porting abm from dmcu to dmcub missed one register write.
[How]
Add this register write in the SetBacklightLevel sequence.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Renoir's pipe VM flags are not correctly updated if pipe strategy has
changed during some scenarios. It will result in watermarks mistakenly
calculation, thus underflow and garbage appear.
[How]:
Correctly update pipe VM flags to pipes which have been populated.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aconnector is not necessary to be NULL in order to read dpcd
successfully.
Actually if we rely on checking aconnector here, we won't be able
to turn off all displays before doing display detection. That will
cause some MST hubs not able to light up.
[How]
Remove aconnector check when turning off all displays at
hardware initialization stage.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <joseph.gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:1017:50:
warning: ‘video_optimized_pixel_rates’ defined but not used [-Wunused-const-variable=]
static const struct pixel_rate_range_table_entry video_optimized_pixel_rates[] = {
^~~~~~~~~~~~~~~~~~~~~~~~~~~
commit d8cd587d2b ("drm/amd/display: removing MODULO change for dcn2")
left behind this unused vairable, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable dp_ref_clk_khz is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following gcc warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_hw_sequencer.c:43:46:
warning: ‘reg_offsets’ defined but not used [-Wunused-const-variable=]
static const struct dce80_hw_seq_reg_offsets reg_offsets[] = {
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add debugfs to get HDCP capability. This is also useful for
kms_content_protection igt test.
Use:
cat /sys/kernel/debug/dri/0/DP-1/hdcp_sink_capability
cat /sys/kernel/debug/dri/0/HDMI-A-1/hdcp_sink_capability
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Query the hdcp caps of a link, it is useful and can be reported to the user
[How]
Create a query function and call it during link detect
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When display is connected with a native DP port, DP2 mode register value
is a don't care. Driver mistakenly reduce max supported lane count to 2
lane based on the don't care value.
[how]
Add additional check only if USB C DP alt mode is enabled, we will
determine max lane count supported based on current mode.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.
[How]
- move from else-if to unconditional or
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In most cases, DRAM watermark is large enough that the result of the
condition to increase TTU doesn't change after DRAM watermark is
increased. However, there is are cases where the condition fails and
becomes true after DRAM watermark is increased. This results in minTTU <
DRAM watermarks which leads to PSR hang since p-state is requested but
not allowed.
[How]
Check whether to update TTU after DRAM watermark is updated.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New formula + cursor change causing underflow
on certain configs
[How]
Rever to old formula
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
usb3->usb2 switch system hang.
driver needs to limit the max sink cap based on DP4 mode.
[how]
based on s_dpalt check and DP4 check:
limit the USB-C DPALT DP maximum supported lane count.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dml merges mpc/odm combine pipes to do calculations. This merge is
imperfect if there is a viewport overlap. This change saves pre overlap
viewport for dml use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.
We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.
[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.
We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.
This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.
[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.
This matches what we do for DCN now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
blank all dp stream would impact edp
[how]
only blank the one which will be powered off
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When dmcub is the default we no longer wish to create the psr and dmcu
objects. Currently a dc debug flag is used to implement this, but these
flags aren't populated until after dcn21_resource_construct is called.
This means the dmcub objects will never be created. Therefore we must
use a dc config flag, which is populated before dc resource construct.
[How]
Add a dc config flag.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The power_down() function was only defined for specific asics and will
crash the system if it is called by an asic with eDP connected that does
not have it defined.
[HOW]
Add a check for the function's existence before calling it.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overlay planes disappear when the plane's alpha blending mode or global
opacity is modified.
These are considered UPDATE_TYPE_MEDIUM and trigger the update_mpcc path
in the DCN hardware sequencer.
On DCN10 we have an "optimization" to avoid touching the blending tree
on these updates, but this is actually required behavior based on how
update_mpcc is structured.
For full updates we acquire a MPCC for the plane, remove it if it
already exists then reinsert it after with insert_plane.
The call to insert_plane can take an optional mpcc to insert the new one
above to preserve the current blending order. The update_mpcc hwseq
function doesn't do this so the overlay gets sent to the very bottom
of the tree.
[How]
Copy the check over from DCN10 to DCN20. The only time we need to
actually touch the tree really is the full update, so this is also
an optimization on top of the fix.
Fixing the logic for insert_plane is rather simple (cache the bot_mpcc
and pass it to insert_plane) but is a change that impacts most display
usecases.
For now stick with the optimization.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
power off dp receiver directly cause garbage during hw init
[how]
blank dp stream and then power off receiver
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On headless boot a DIG may be turned on by VBIOS on RN. This leads to
display_count being non-zero in hybrid graphics cases leading to SMU
DISPLAY_OFF message not being sent.
[HOW]
Power down hardware on boot
if seamless boot is not occurring
(power_down_display_on_boot == 1)
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver must pass abm config table to dmub fw. This provides various
parameters for abm functionality.
[How]
There is too much data to be passed in an inbox message, so we must pass
this data using an indirect buffer. Copy the table to cw7 via x86,
driver copies to fw_state structure.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed before the link is enabled to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen with DSC timings like 4k144Hz or 8k60Hz.
[how]
Move DSC programming from before enabling stream to before enabling link
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If no free pipes are available, acquire_first_split_pipe is called to
get a pipe to use. This call may alter the ordering of the pipes in the
list so that, for example, the tail pipe changes.
If acquire_first_split_pipe returns the tail pipe, we'll have free_pipe
== tail_pipe. What tail_pipe refers to is not the current tail_pipe, but
what was previously the tail pipe - i.e. prior to the call to
acquire_first_split_pipe
The logic that follows will link free_pipe to the tail pipe, referring to
the current tail pipe. However, since tail_pipe is cached from before the
call to acquire_first_split_pipe, the wrong tail pipe will be used, and
it will end up being linked to itself, creating a loop that, if traversed,
will result in a soft hang.
[How]
Do not cache the tail pipe. Instead, check the tail pipe after the call to
acquire_first_split_pipe is made.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Aligh with DP spec wanted to follow same naming convention.
[How]:
Changed the macro name of the dpcd address used for getting requested
test-pattern.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-2-animesh.manna@intel.com
[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.
[HOW]
Add check for clock tables fclk entry's voltage as well
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.
[How]
- move from else-if to unconditional or
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.
We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.
[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.
We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.
This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.
[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.
This matches what we do for DCN now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM already supports tracing DPCD transactions, there's no reason for
the existence of this function. Also, it prints one byte per-line which
is way too loud. So, just remove it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues in dc_link file, on dc_link_construct and
translate_encoder_to_transmitter as suggested by checkpatch.pl.
Types covered:
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
CHECK: Alignment should match open parenthesis
CHECK: Comparison to NULL could be written
CHECK: Logical continuations should be on the previous line
CHECK: Blank lines aren't necessary after an open brace '{'
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on the file dc_link between is_same_edid and
get_ddc_line as suggested by checkpatch.pl.
Types covered:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: braces {} are not necessary for single statement blocks
CHECK: Comparison to NULL could be written
CHECK: Lines should not end with a '('
CHECK: Alignment should match open parenthesis
CHECK: Using comparison to false is error prone
CHECK: Using comparison to true is error prone
WARNING: Avoid multiple line dereference - prefer 'link->dpcd_caps.sink_count.bits.SINK_COUNT'
CHECK: Unnecessary parentheses around
WARNING: Missing a blank line after declarations
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on the file dc_link until detect_dp func as
suggested by checkpatch.pl.
Types covered:
CHECK: Please don't use multiple blank lines
CHECK: Comparison to NULL could be written
ERROR: space required before the open parenthesis '('
CHECK: Alignment should match open parenthesis
CHECK: Lines should not end with a '('
WARNING: please, no space before tabs
WARNING: Comparisons should place the constant on the right side of the test
WARNING: braces {} are not necessary for single statement blocks
CHECK: Please don't use multiple blank lines
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can't call dmub_abm_enable_fractional_pwm from dmub_abm_create as
dmub_srv is still null at this init stage, and therefore can't call to
fw.
[How]
Move call to dmub_abm_init_backlight. This should be the first call from
the driver for ABM.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML expects num_states to exclude the duplicate state.
[How]
Set num_states to correct value to prevent array off-by-one error. Also
refactor max clock level code for diags.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CTM was only supported at CRTC level and we need color space conversion
in linear space at plane level.
[How]
- Add plane-level CTM to dc interface
- Program plane-level CTM in DCN
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some monitors extreme flickering can occur while using LFC for if
we're not doing the DRR timing update for V_TOTAL_MIN / V_TOTAL_MAX at
the DP start of frame.
Hardware can default to any time in the frame which isn't the behavior
we want.
[How]
Add a new function for setting the double buffering mode for DRR timing.
Default to DP start of frame double buffering on timing generator init.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
P010 pixel format is not declared as supported in DRM and DM.
[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics scaling test failing to set required number of vertical taps
in 4:2:0 surface case
[How]
In dpp3_get_optimal_number_of_taps() need to use LB_MEMORY_CONFIG_3 for
4:2:0 surface case. In resource_build_scaling_params() make sure to also
set plane res alpha enable based on updated surface state
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds logic that will determine if pipes need merging during validation.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
before update dpp DTO, we check dppclks in context to determine it is
changed or not, but dppclks in context will be updated anyways after
flip is done, so compare dppclks in context will always get an equal
result.
[How]
Add pipe dpp clks in dccg and compare values between dccg and context.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Causes regression with MST DSC displays not lighting up after DPMS
[how]
Revert commit 8cc426d79b ("drm/amd/display: Program DSC during timing programming")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow happened when playing video on 1366x768 + 4K clone mode due to
incorrect handle watermark change flag and lower down clocks to early.
[How]
Check watermark change flag when decide doing optimized, and check
optimized required flag to do clock update.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
this register not exist in some asic, based on request remove this from
dc.
[how]
add guard for sanization.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should check MST BU support capability on output port before building
vsc info packet.
[How]
Add a new definition for port and sink capability check.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless boot cases, self refresh control registers are not
programmed on boot. In certain hybrid graphics cases this may cause
cstate entering to get blocked causing a hang.
[HOW]
Program self refresh control register on boot.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable/disable psr on dmcub and fallback to dmcu
when necessary.
[How]
Use dc config option to do so.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The default value for disable_dmcu is true, even for asics that require
dmcu.
[How]
Set flag properly per asic.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A "dcn20_program_front_end_for_ctx" warning is observed on Renoir.
Since the resource definition doesn't explicitly disable triplebuffer
flips like Navi10 DC actually attempts to go and setup triplebuffering
even when we pass in false to the plane state.
If we hit a full update after triplebuffering has been setup we see the
assertion since we don't expect full updates while performing
triplebuffer flips.
Normally this would get reset back to false whne we pass in the new
plane state, but since we never actually copy the flag when doing
surface updates this doesn't happen.
[How]
Copy the flag onto the plane update based on the requested surface
update state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now only stream count is used to avoid split. This change updates
the W/A to check plane count instead.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug a HDMI monitor during entering S0i3 or DPMSOFF state due to
entering infinite loop when calling vbios to program pixel clocks. In
this scenario, pll is enabled but phy is not, and there is not a
programing guide for this case.
[How]
Before we having the proper programing guide, before disable pll, doing
a phy enable and disable to avoid the issue.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When reprogram MSA with updated color space, the test color space shows
inconsistency. Linux has separate routine to set up test pattern color
space, but it fails to configure RGB.
[How]
Add RGB to test pattern.
Fixes: 43563bc2e6 ("drm/amd/display: update MSA and VSC SDP on video test pattern request")
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If "speed" is zero then we use it as a divisor to find "prescale". It's
better to move the check for zero to the very start of the function.
Fixes: 9eeec26a13 ("drm/amd/display: Refine i2c frequency calculating sequence")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can remove the NULL check for "res_ctx" and
"res_ctx->pipe_ctx[i].stream->link". Also it's nicer to align the
conditions using spaces so I re-indented a bit.
Longer explanation: The "res_ctx" pointer points to an address in the
middle of a struct so it can't be NULL. For
"res_ctx->pipe_ctx[i].stream->link" we know that it is equal to "link"
and "link" is non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dcn20_funcs and dcn21_funcs struct, the member ".dsc_pg_control = NULL"
should be removed due to .dsc_pg_control be assigned to dcn20_dsc_pg_control.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem Description:
Currently we are checking internal fused rev id with pci rev id. However, fused
internal rev id is the same on all raven2 parts (in which Dali and Pollock were
based on too), thus Pollock detection fails
Fix:
use the pci rev to preform the detection for bandwidth calculations.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dpp2_get_optimal_number_of_taps function is never used. Removing
just for code cleaning up.
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FEC capability query should not be affected by debugging decision on
whether to disable FEC. We should not determine if display supports FEC
by checking debug option.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
Need debug options to control lightl/deep sleep
[How]
Add registry for memory power control
Signed-off-by: Braden Bakker <Braden.Bakker@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is possible even if sink signal is MST but driver enables SST stream.
We should not determine if we should do MST authentication based on
sink's capability.
Instead we should determine whether to do MST authentication based on
what we have enabled in stream.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some lttpr devices do not work properly when lttpr mode is configured
after link settings.
[How]
Move lttpr configuration before lane settings.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:
In function hubp21_set_vm_system_aperture_settings:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_hubp.c:343:23:
warning: variable mc_vm_apt_default set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when changing display clock, SMU need to use power up DFS and use
DENTIST to ramp DFS DID to switch target frequency before switching back
to bypass.
[How]
fixed the minimum display clock to 100MHz, it's W/A the same with PCO.
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System will crash when trying to access local sink in
core_link_enable_stream in MST case.
[How]
Access patches directly from stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently clock table struct is very far down in the bounding box struct
making it hard to find while debugging, especially when using the
dal3dbgext.
[HOW]
Move it up so it is the first struct defined, and therefore much easier
to find and access.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to assign surface size rather than viewport size for surface size
dml variable.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update TTU properly if DRAMClockChangeWatermark changes. If
TTU < DRAMClockChangeWatermark, we pstate won't be allowed and we will
hang in some PSR cases.
[How]
Update TTU if DramClockChangeWatermark value increases (only if TTU was
dependent on the watermark value on the DRAMClockChangeWatermark value
in the first place).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
RV2 and variants are indistinguishable by hw internal rev alone, need to
be distinguishable in order to correctly set max vlevel. Previous
detection change incorrectly checked for hw internal rev.
[HOW]
Use pci revision to check if RV2 or low power variant Correct a few
overlapping ASICREV range checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Add infrastructure to enable and disable PSR on DMCUB.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn20_populate_dml_pipes_from_context to correctly handle odm
when no surface is provided.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern was link level but the whole
asic should be affected.
[How]
- change old link flag to dc level
- new bit in dc->work_arounds set by DM
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays clear ignore MSA bit on mode change, which cause
blackscreen when programming variable vtotals. Ignore MSA bit needs
programming needs to be delayed or re-set to be retained.
[How]
Create patch to delay programming ignore MSA bit after unblanking
stream.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A software workaround is required for all vendor-built cards on platform.
[How]
When performing DP link training, we must send TPS1 before DPCD:100h is
written with the proper bit rate value. This change must be applies in
ALL cases when LT happens.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some structures and functions meant only to be used in the
scope of that single rn_clk_mgr c file.
[How]
Make structs and funcs static if only meant to be used within
rn_clk_mgr
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add optimization to allow pstate change support when all displays
are off in DCN2.
[How]
Add clk_mgr_helper_get_active_plane_cnt() to sum plane_count for all
valid stream_status[]. If plane_count is 0, then there are no active
or virtual streams present. Use plane_count == 0 as extra condition to
enable p_state_change_support in dcn2_update_clocks().
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bugs occur when TX interrupt comes in when no USB-C on board.
[How]
Check PHY for USB-C before enabling TX interrupt in DMCU FW.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently there is a minor error in scaling filter coefficients
caused by truncation to fit the HW registers.This error accummulates
with increased taps, but has gone unnoticed due to vast majority of
scaling being done with only 4 taps.
Scaling filters are now updated using HW team's filter generator
which has quantization error minimization built in.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since the i2c payload allocation can fail need to check return codes
[How]
Clean up i2c payload allocations and check for errors
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:980:36:
warning: address of 'sink->edid_caps.panel_patch.skip_scdc_overwrite'
will always evaluate to 'true' [-Wpointer-bool-conversion]
if (&sink->edid_caps.panel_patch.skip_scdc_overwrite)
~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
1 warning generated.
This is probably not what was intended so remove the address of
operator, which matches how skip_scdc_overwrite is handled in the rest
of the driver.
While we're here, drop an extra newline after this if block.
Fixes: a760fc1bff ("drm/amd/display: add monitor patch to disable SCDC read/write")
Link: https://github.com/ClangBuiltLinux/linux/issues/879
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's used by more than just DCN2.0. Fixes missing symbol when
amdgpu is built without DCN support.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to cover dcn2.x related headers.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Tested-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver needs to know PSR state.
[How]
Use GPINT to call to firmware and get psr state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm scaling calculations are only done when adding initial
odm pipe. Any scaling re-calculations will mess up odm because of this.
This change resolves the problem by updating scaling split logic to
handle odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the struct dc_panel_patch, we have a field named
manage_secondary_link which is not used by any part of the code. This
commit drops the unused field.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register defines are redundant or updated
[How]
Update register defines
Remove some redundant defines
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in dcn10_apply_ctx_for_surface(), if we hit !top_pipe_to_program,
pipe_ctx->update_flags could not get cleared.
[How]
Moved clearing pipe_ctx->update_flags logic before if
(!top_pipe_to_program) to gurantee pipe_ctx->update_flags get cleared.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set version is currently not called.
[How]
Add call to set version from copy settings. This
should be the only time this is called as the eDP
caps should never change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Vendor dongle requires propietary OUI and handshake sequence.
[HOW]
Add a new structure to dc_init_data, to allow creator to pass
an override vendor_oui. This value will be written to DP_SOURCE_OUI
instead of AMD signature, when dpcd_set_source_specific_data is
called.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With the fallback case in place for command table offloading via DMCUB
it's no longer an error for the command table to be missing specific
entries.
[How]
Drop the BREAK_TO_DEBUGGER();
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
before we exit early in edp_reciever_ready if we detect that panel
is not edp or below rev 1.2. This will skip the backlight/t7 delay panel
patch.
[how]
edit logic to ensure panel patch is applied regardless of edp rev.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, gcc spews a warning as:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubbub.c: In function ‘hubbub1_verify_allow_pstate_change_high’:
./include/drm/drm_print.h:316:2: warning: ‘debug_data’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because the code checks against a static value although it's
basically a constant and guaranteed to be set.
This patch changes the type prefix from static to const for addressing
the compile warning above and also for letting the compiler optimize
better.
Fixes: 62d591a8e0 ("drm/amd/display: create new files for hubbub functions")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not turning off the mst hub before detection on reboot
causes us to not be able to light up displays with mst hook
[how]
on hw init, see if any displays are lit up. if so, turn them off
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these registers should have been double buffered. SW workaround we will have SW program the more aggressive (lower) values
whenever we are upating this register, so we will not have underflow at expense of less optimzal request pattern.
[How]
there is a driver bug where we don't check for 0, which is uninitialzed HW default. since 0 is smaller than any value we need to program,
driver end up with not programming these registers
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] old panel has been enabled for window driver but not linux.
[How] enable oled panel support for linux. this patch is dc part.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
enum dc_log_type has more than 32 entries. User cannot set larger entries,
like LOG_DSC. Logs from LOG_GAMMA_DEBUG where being printed even though
flag was not enabled, because dal_logger_should_log check erroneously
passed.
[HOW]
Change struct dal_logger.mask and struct dc_init_data.mask to uint64_t.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hyperV flag should be passed from dm to DC, and override the
nv12 flip workaround flag.
[How]
Add flag to phy address config struct and pass the value in dm.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic is only good for 15W parts. Other configuration
need a smarter logic to match clk levels with pp table in the fuse.
[How]
Cache all 8 DPM level's clock data, find lvl that match each pstate
in the pp table and build input into DML base on that
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hwss should not guess what type of pipe lock is needed.
The caller of the lock function should know
the right type of pipe lock.
Decouple the setup of global lock outside of pipe control lock
logic.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The break in apply_ctx_interdependent_lock() may potentially
lead to early break from the loop leaving update plane unlocked
[How]
Remove break
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
int i can go out of boundary which will cause crash
[How]
Fixed the maximum value of i to avoid i going out of boundary
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After locking refactor GSL is not acquired properly
resulting in immediate flip issues.
[How]
Do not copy old GSL state anymore since GSL is acquired
earlier now.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics team reported various issues found when enabling warnings as errors
[How]
Fix implicit conversions
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC updates only set type to FULL UPDATE, but doesn't
flag the change
[How]
Add DSC flag update flag
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
We found out that the register we read actually gets reset by SMU
after we loose power, meaning this always returns true
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to dp_enable_link_phy are using default/invalid values for clock id
and link settings.
[How]
Move workaround code to after its parameter variables are determined.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Must know psr version during runtime.
[How]
Add set psr version message structures.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A for-loop is iterating from 0 up to 1000 however the loop variable count
is a u8 and hence not large enough. Fix this by making count an int.
Also remove the redundant initialization of count since this is never used
and add { } on the loop statement make the loop block clearer.
v2: drop useless else (Walter Harms)
Addresses-Coverity: ("Operands don't affect result")
Fixes: ed581a0ace ("drm/amd/display: wait for update when setting dpg test pattern")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allocation isn't required and can fail when resuming from suspend.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1009
Signed-off-by: Dor Askayo <dor.askayo@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 80adaebd2d.
[WHY]
This change was working around a regression that occured in this:
commit 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
With the fix to run verify_link_cap when the SINK_COUNT of
dongles becomes non-zero this change is no longer needed.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FMT has limitation to support YCbCr420 with h_active greater than 4096.
[how]
Use odm combine to overcome the limitation.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver didn't init hw i2c speed cause hdcp hw cannot
send command, because the default value of speed register
is 0x2.
[How]
Restore the default speed when release i2c engine
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
MSA will be deprecated in the future.
Need to support VSC during DP test automation.
[how]
Do not disable VSC during DP test automation.
TODO - need to add VSC update on DM side on test request.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB command table doesn't support ATOM_ENABLE/ATOM_DISABLE anymore
so we never end up calling the DCN init path in DMCUB.
[How]
Map ATOM_ENABLE to ATOM_INIT only for DMCUB command table offloading.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoded fixed values are not proper.
[How]
Use enum values instead of fixed numbers.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HG mode, vbios didn't call DispController_Init to program NV1x
XTAL_REF_DIV value when ASIC_INIT, but driver read XTAL_REF_DIV
to calculate i2c reference frequency. it cause i2c frequency change
from 100kHz to 200kHz.
[How]
remove get_speed function and calculate reference frequency at
set_speed functiton.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The types for dummyinteger1 and dummyinteger2 are unsigned
as part of the DML spec. They should not be long.
[How]
Make them unsigned int instead of long.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver use pipe_ctx to reallocate payload may cause allocate
payload twice on same sink with split pipe.
[How]
Drvier must to check pipe_ctx is split pipe or not to avoid
reallocate payload twice on same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the command table isn't available then we can fallback to DMCUB
offloading if it's enabled and available.
[How]
Instead of assigning NULL for supported command table functions we can
fallback to the DMCUB when it's available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DP 1.4a Spec requires that training pattern only under certain
specific conditions. Currently driver will re-send
training pattern every time voltage swing value changes,
but that should not be the case.
[How]
Do not re-send training pattern every time VS values
are different. Only send it on the first iteration.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On video test pattern request we need to update MSA and VSC so
it will match the requested test pattern dynamic range field.
[how]
Update dynamic range field in MSA and disable VSC as updating VSC
info packet is complicated and not required for test pattern purpose.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DPG is used to generate both blank and test automation test pattern.
When test automation is running the requested test pattern can be
overriden by the blank or unblank call because it is using the same
hardware.
[how]
When test pattern is requested, skip blank or unblank.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Try to allocate MST payload but receive HPD short pulse with link loss
casue driver allocate payload twice. It cause monitor can't light up
successfully.
[How]
When driver receive HPD short pulse with link loss, we need to
deallocate payload then allocate payload.
Then we will not allocate payload twice with same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to fix DML portability issues to enable SW unit testing around DML
[how]
Move calcs into dc include folder since multiple components reference it
Remove relative paths to external dependencies
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The rapid msleep operation causes the white line garbage when
DAL check flip pending status in SetVidPnSourceVisibility.
To execute this msleep will induce context switch, and longer
delay could cause worse garbage situation.
[how]
To replace msleep with mdelay.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only need to do surface flip for video plane via dmcub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently if seamless boot is enabled, we will skip double buffer enable
for OTG_BLANK. However, we need the double buffer enable in order to
block global sync signals when OTG becomes blanked (for PSR). Blocking
global sync signals prevent pipe from requesting data.
[How]
Move tg_init before seamless boot check.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpcd cap mismatch in 2200 vs base
[How]
Add monitor patch which using based caps to overwrite 2200
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently we wait for test pattern after each pipe is programmed. For
ODM combined scenario it will cause test pattern is shown on only half
screen for 1 frame. This is not desirable.
[how]
No wait between odm pipe programming, only wait after all pipes are
programmed.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCU need to wait a vblank to handle psr enter command. When psr exit
coming before vblank, the psr exit command will be skip because current
psr state is disable.
[How]
remove psr state condition when psr exit case
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML Initialization was previously done on dcn21_resource initialization.
This meant that DML soc struct was populated with hardcoded values.
[How]
Move DML initialization to after updating bounding box, to use clock table
values from SMU.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework surface programming for RN to separate preparing parameters and
register programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.
[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more fields to support upcoming dml versions
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds
[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Test pattern should be applied to hardware when exiting set test pattern
function.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI
[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dummy pstate latency is 0 we should report the actual
pstate support, and not that pstate is always supported.
[How]
Don't always program pstate support true
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that lttpr_caps has the mode set to repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.
[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
While doing seamless boot I made some changes
to dcn2 hubbub functions, missed a link
[how]
link hubbub1 func to hubbub2 usage. It has already
been successfully linked in dcn1 and 3.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.
[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needed to reprogram vblank_start in dml properly in order to get the
correct dlg params to program VTG.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous implementation we may have residual chroma address offset
if transition from wa enable -> wa disable.
[How]
Clear address offset cache when viewport updates. Also update the
vp size check condition to account for rotation angle
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The conversion to bool is not needed, remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
read_current_link_settings_on_detect() on eDP 1.4+ may use the
edp_supported_link_rates table which is set up by
detect_edp_sink_caps(), so that function needs to be called first.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Martin Leung <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only a single voltage level should be available to Pollock (min level)
Pollock & Dali get misidentified as Renoir, use wrong clk mgr constructor
[HOW]
Add provided Pollock IDs to ASIC Rev. ID list.
Create new Pollock ASIC RID check, fix RV2 & Dali ASIC checks.
Check RID and set max voltage level to 0 if Pollock is detected.
Work around broken ASICREV_IS_RENOIR, IS_RAVEN2, etc. checks by
performing Dali/Pollock checks before they can be misidentified as RN.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a use case that link loss happens accidentally,
and we need to recover that link loss as soon as possible.
Under this circumstance, we will perform link training,
and try to recover the link that's just lost.
However, if link PHY is disabled before link training
happens, then DP display will never come back again.
Also, please note that dropping this disable_phy function
call won't break USB-C hotplug functionality.
(This line of code was firstly introduced associated with
a patch to fix USB-C hotplug issue)
[How]
Don't disable DP transmitter and its encoder before link
training happens, even if link loss is detected.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there is limited link bandwidth on a MST network,
it must be divided fairly between the streams on that network
Implement an algorithm to determine the correct DSC config
for each stream
The algorithm:
This
[ ] ( )
represents the range of bandwidths possible for a given stream.
The [] area represents the range of DSC configs, and the ()
represents no DSC. The bandwidth used increases from left to right.
First, try disabling DSC on all streams
[ ] (|)
[ ] (|)
Check this against the bandwidth limits of the link and each branch
(including each endpoint). If it passes, the job is done
Second, try maximum DSC compression on all streams
that support DSC
[| ] ( )
[| ] ( )
If this does not pass, then enabling this combination of streams
is impossible
Otherwise, divide the remaining bandwidth evenly amongst the streams
[ | ] ( )
[ | ] ( )
If one or more of the streams reach minimum compression, evenly
divide the reamining bandwidth amongst the remaining streams
[ |] ( )
[ |] ( )
[ | ] ( )
[ | ] ( )
If all streams can reach minimum compression, disable compression
greedily
[ |] ( )
[ |] ( )
[ ] (|)
Perform this algorithm on each full update, on each MST link
with at least one DSC stream on it
After the configs are computed, call
dcn20_add_dsc_to_stream_resource on each stream with DSC enabled.
It is only after all streams are created that we can know which
of them will need DSC.
Do all of this at the end of amdgpu atomic check. If it fails,
fail check; This combination of timings cannot be supported.
v2: Use drm_dp_mst_atomic_check to validate bw for certain dsc
configurations
v3: Use dc_dsc_policy structure to get min and max bpp rate
for DSC configuration
Acked-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.
memset to 0 to avoid this
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:85:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:88:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:225:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:226:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:251:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:252:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:256:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:257:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:269:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:682:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_rq_dlg_calc_21.c:1013:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20v2.c:962:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:110:6-13: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:113:2-9: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:243:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:244:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:267:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:268:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:272:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:273:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:283:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:285:3-11: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:673:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn20/display_rq_dlg_calc_20.c:961:1-9: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:157:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:159:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:161:46-64: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:163:2-20: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:289:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:290:1-12: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:341:3-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/calcs/dce_calcs.c:343:4-15: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4124:3-28: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:4128:5-30: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:5207:3-37: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:186:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn20/dcn20_hwseq.c:189:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:482:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:485:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's required for debug purposes.
[how]
Add a dsc_bpp_increment_div debug option that overrides DPCD
BITS_PER_PIXEL_INCREMENT value. The value dsc_bpp_increment_div should
be set to is the one after parsing, i.e. it could be 1, 2, 4, 8 or 16
(meaning 1pix, 1/2pix, ..., 1/16pix).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP is internal link and link loss is unexpected.
It is typically going to be PSR related errors, which is
handled separately.
[How]
Check for eDP and skip check for link loss
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor disappears for some SLS displays that are rotated 180
and 270 degrees. This occurs when there is no pipe split being
done ( ex. 3 or more displays ). The cursor calculations assume
pipe splitting is done so when it calculates the new cursor
position in hwss.set_cursor_position(), it is out-of-bounds so
it disables the cursor in hubp.set_cursor_position().
[How]
In non pipe split cases, calculate cursor using viewport size
( width or height ) instead of viewport size * 2 ( the two
because pipe splitting divides the rectangle into two ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous formula for calculating DPP CLK DTO was
hard to understand.
[How]
Replace with easier to understand formula that produces
same results.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DAL3 should support SRIOV
[how]
Add support for the virtual dal flag. This flag should skip
most/all of DC construction since the HW isn't accessible, but
still construct WindowsDM (almost) normally but with only SW display
targets
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix manual trigger source correctly be TRIGA for DCN2
rather than MANUAL_FLOW.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 and DCN2 extended timeout support cap is not set correctly.
[How]
Set extended timeout support for ASIC families to their right values.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
According to eDP spec, max T7 delay should be 50 ms. Current code uses 300
retry counters may not be accurate enough for different panels.
[How]:
Use absolute time stamp to achive accurate delay.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we rotate 270 in mixed SLS mode, the recouts occupy the
right side of the display. So all the recout_skip_v values
are relative to the left side of the display. This causes
adjust_vp_and_init_for_seamless_clip() to incorrectly increase
the data->viewport.height for that recout. The rotation looks
like the bottom half is duplicated twice.
[How]
recout.x values are being adjusted based on
stream->timing.h_border_left. Instead of using h_border_left,
use dst.x to represent the border. Shift dst.x by the amount of
stream->timing.h_border_left and set
stream->timing.h_border_left to 0. Do all the calculations
and then revert stream->timing.h_border_left and
stream->dst.x back to their original values.
When calculating pipe_ctx->plane_res.scl_data.h_active,
make sure to use the original stream->timing.h_border_left
value.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain instances, there was a reliance on pipe indexing being accurate. However, this
assumption fails with harvesting of pipes 1 or 2, which can occur in production B6 parts.
HW hang would occur as a result.
[How]
Use hubp index for mpcc, and do mpc_init for all theoretical pipes (including disabled ones).
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After read the 3rd Edid blocks, we will reset segment to 0,
which causes this VR fail to read Edid successfully.
[How]
Skip to reset segment to 0 for this VR device.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Set second screen only then unplug external monitor
2. Enter to S4 then plug in external monitor
3. Resume from S4, eDP will not turn off when OS set
second screen only
Sometimes OS will not set eDP power up cause eDP dpms_off
keep true then driver skipp disable stream
[How]
When drvier try to disable stream, add link status condition
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add warmup escape support, for diags, in a way that is possible to
choose a new or an existing sequence. For achieving this goal, this
commit adds separated MCIF buffer as VCN request.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Scaling better handled by upper layers before pipe splitting.
[How]
Remove DC code for integer scaling and force cursor update if
viewport or scaling changes occur to prevent underflow from
invalid cursor position.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc previously had bugs that interfered with the ability to inherit a
timing from a device with multiple streams (without flash/blanking).
After this fix there is still a dependency on UEFI support.
[how]
fixed 3 bugs: loaded MPC state, changed bw_optimize flag to a counter
instead of a boolean, and reading dpp/disp clk from HW to ensure we
don't raise the clock's when we're not supposed to.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, pipe resources are assigned to an index that matches the pipe position.
However, if pipe 1 or 2 is disabled, there will be a gap in the arrays which causes a crash when iterating based on pipe_count.
[How]
Fix resource construct to assign resources to minimum available array index.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need previously implemented chroma vp wa to work for rotation cases.
[How]
Implement rotation specific wa.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is one opp per pipe. For certain RN parts, the fourth pipe is disabled, so there is no opp for it.
res_cap->num_opp is hardcoded to 4, so if we use that to iterate over opps we will crash.
[How]
Use the pipe_count value instead, which is not hardcoded and so will have the correct number.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
YQ should be limited range for all cases.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hardcoded number is used today
[How]
Add definition for number of BL data points
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some use cases we need to be able to adjust the maximum target bpp
allowed by DSC policy.
[How]
New interface dc_dsc_policy_set_max_target_bpp_limit
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Lack of proper timing caused intermittent underflow on unplug external DP.
A previous fix was invalid and caused S0i3 regression, so had to be reverted.
[How]
When unlocking pipe, wait for no pipes to have flip pending before unlocking.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The earlier change: "check phy dpalt lane count config"
uses link encoder registers not defined properly.
That caused regression with mst-enabled display not
lighting up.
[How]
Add missing reg definitions.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc20 containes several FPU-dependent functions without proper FPU
kernel mode enable/disable wrappers. Add the required wrappers
for both x86 and POWER.
This enables Navi DC20 support for POWER systems.
v2: fix compilation
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN requires floating point support to operate. Add the appropriate
x86/ppc64 guards and FPU / AltiVec / VSX context switches to DCN.
Note that the current DC20 code doesn't contain all required FPU
wrappers on x86 or POWER, so this patch is insufficient to fully
enable DC20 on POWER.
v2: s/X86_64/X86/g to retain previous behavior.
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Introduce DC_FP_START()/DC_FP_END() macros to help enable floating
point kernel mode support across various architectures.
v2: move copyright update to commit which adds the changes
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.6-2019-12-11:
amdgpu:
- Add MST atomic routines
- Add support for DMCUB (new helper microengine for displays)
- Add OEM i2c support in DC
- Use vstartup for vblank events on DCN
- Simplify Kconfig for DC
- Renoir fixes for DC
- Clean up function pointers in DC
- Initial support for HDCP 2.x
- Misc code cleanups
- GFX10 fixes
- Rework JPEG engine handling for VCN
- Add clock and power gating support for JPEG
- BACO support for Arcturus
- Cleanup PSP ring handling
- Add framework for using BACO with runtime pm to save power
- Move core pci state handling out of the driver for pm ops
- Allow guest power control in 1 VF case with SR-IOV
- SR-IOV fixes
- RAS fixes
- Support for power metrics on renoir
- Golden settings updates for gfx10
- Enable gfxoff on supported navi10 skus
- Update MAINTAINERS
amdkfd:
- Clean up generational gfx code
- Fixes for gfx10
- DIQ fixes
- Share more code with amdgpu
radeon:
- PPC DMA fix
- Register checker fixes for r1xx/r2xx
- Misc cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211223020.7510-1-alexander.deucher@amd.com
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu is MIT licensed.
Fixes: ec8f24b7fa ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling kzalloc() and related functions requires the
linux/slab.h header to be included:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c: In function 'dcn21_ipp_create':
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_resource.c:679:3: error: implicit declaration of function 'kzalloc'; did you mean 'd_alloc'? [-Werror=implicit-function-declaration]
kzalloc(sizeof(struct dcn10_ipp), GFP_KERNEL);
A lot of other headers also miss a direct include in this file,
but this is the only one that causes a problem for now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An initialization was added for two optional struct members. One of
these is always present in the dcn20_resource file, but the other one
depends on CONFIG_DRM_AMD_DC_DSC_SUPPORT and causes a build failure if
that is missing:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:926:14: error: excess elements in struct initializer [-Werror]
.num_dsc = 5,
Add another #ifdef around the assignment.
Fixes: c3d03c5a19 ("drm/amd/display: Include num_vmid and num_dsc within NV14's resource caps")
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid a compiler warning.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Value obtained from DV is not allowing 8k60 CTA mode with DSC to
pass, after checking real value being used in hw, find out that
correct value is 3600, which will allow that mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To quickly validate whether DMCUB is running and accepting commands for
offload testing we want to intercept a common sequence as part of
modeset programming.
[How]
OTG enable will cause the most impact in terms of golden register
changes and it's a single register write.
This approach was previously done in dcn10 code when it was shared with
dcn20 but it wasn't ported over to the dcn20 code.
Port over start, execute and wait sequence into dcn20_optc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When setting lttpr mode, the new mode to bet is not logged properly.
[How]
Update log message to show the right mode.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for further changes
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems always request passive flip on RN due to incorrect compare
clock state to determine optization.
[How]
Instead of calling memcmp, compare clock state member to determine the
condition.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a timeout occurs after a DEFER, some devices require more retries
than in the case of a regular timeout.
[How]
In a timeout occurrence, check whether a DEFER has occurred before the
timeout and retry MAX_DEFER_RETRIES retries times instead of
MAX_TIMEOUT_RETRIES.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we require HDR_MULT >= 1.0
There are scenarios where we need < 1.0
[How]
Only guard against 0 - it will black-screen image.
It is up to higher-level logic to decide what HDR_MULT
values are allowed in each particular case.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
