[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values.
This change was added for dcn30 and dcn301, but not
for dcn302 and dcn303
[how]
Parse the values from VBIOS if available, and use
them if valid
Fixes: 93669c8e48 ("drm/amd/display: get socBB from VBIOS")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
extended_end_address can only be calculated from the extended_address and
extended_size
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The voltage swing has to start from the minimum level when transmit TPS1 over
Main-Link in clock recovery sequence.
The lane settings from current design will inherit the existing VS/PE values
that could be adjusted by Repeater X, and to use the adjusted voltage swing level
in Repeater X-1 or DPRX could violate DP specs.
[How]
To reset VS from lane settings after LTTPRs have been trained to meet the requirement.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some timings with a large VBlank cause the value to overflow the
register related, while also producing other wrong values in DML output.
[how]
Clamp VStartup at the DCN3.1 maximum value
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video plane is rotate the cursor position is incorrect and not
matching the desktop location.
[How]
When a plane is rotated 90 or 270 degrees, the src_rect.width and height
should be swapped when determining the scaling factor compared to the
dst_rect.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.c:
55:12-42: duplicated argument to && or ||
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Function 'dpp1_full_bypass' is declared twice, so remove the repeated
declaration and unnessary blank line.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix
the following warning by replacing a /* fall through */ comment
with the new pseudo-keyword macro fallthrough:
rivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:672:4: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER:
^
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings, so in order to globally enable
-Wimplicit-fallthrough for Clang, these comments need to be
replaced with fallthrough; in the whole codebase.
Link: https://github.com/KSPP/linux/issues/115
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC reports the following warning with W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:3635:17:
warning:
variable ‘status’ set but not used [-Wunused-but-set-variable]
3635 | enum dc_status status = DC_ERROR_UNEXPECTED;
| ^~~~~~
The variable should be used for error check, let's fix it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current watermarks end up programming lowers watermarks which
results in screen flickering and underflow for certain modes like 1440p.
[How]
Add 11us to stutter exit & stutter enter plus exit watermark.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c:917:56-57:
pstate_enabled: first occurrence line 935, second occurrence line 937
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP LL Compliance tests require that the first DPCD transactions after a
hotplug have a timeout interval of 3.2 ms. In cases where LTTPR is
disabled, this means that the first reads from DP_SET_POWER and DP_DPCD_REV must have an extended
timeout.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When changing the DISPCLK_WDIVIDER value from 126 to 127, the change in
clock rate is too great for the FIFOs to handle. This can cause visible
corruption during clock change.
HW has handed down this register sequence to fix the issue.
[HOW]
The sequence, from HW:
a. 127 -> 126
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_DROP_PIXEL for (N-4) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 126
Because of frequency stepping, sequence a can be executed to change the
divider from 127 to any other divider value.
b. 126 -> 127
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_ADD_PIXEL for (12-N) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 127
Because of frequency stepping, divider must first be set from any other
divider value to 126 before executing sequence b.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware has handed down a new sequence requiring the value of this
register be read from clk_mgr.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 spec says that multiple LTTPRs must not be accessed in a
single AUX transaction.
There may be other places in future where breaking up AUX accesses is
necessary.
[HOW]
Partition the entire DPCD address space into blocks. When an incoming AUX
request spans multiple blocks, break up the request into multiple requests.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that
"A DPTX shall distinguish I2C_DEFER|AUX_ACK from AUX_DEFER. AUX retries
due to
I2C_DEFER are not counted as part of minimum 7 retires (sic) upon
AUX_DEFER’s"
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that TX devices must retry at least 7 times when
receiving an AUX DEFER reply from RX. In addition, the specification
states that the TX shall not retry indefinitely, and gives a suggestive
timeout interval of 50ms.
[HOW]
Keep retrying until both 7 or more retries have been made, and the 50ms
interval has passed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
7 is the minimum number of retries TX must attempt on an AUX DEFER, not
the maximum.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some DPCD addresses, notably LTTPR Capability registers, are expected to
be read all together in a single DPCD transaction. Rather than force callers to
read registers they don't need, we want to quietly extend the addresses
read, and only return back the values the caller asked for.
This does not affect DPCD writes.
[HOW]
Create an additional layer above AUX to perform 'checked' DPCD
transactions.
Iterate through an array of DPCD address ranges that are marked as being
contiguous. If a requested read falls within one of those ranges, extend
the read to include the entire range.
After DPCD has been queried, copy the requested bytes into the caller's
data buffer, and deallocate all resources used.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP specifies that an LTTPR device is only present if PHY_REPEATER_CNT is
0x80, 0x40, 0x20, 0x10, 0x08, 0x04, 0x02, or 0x01.
All other values should be considered no LTTPRs present.
[HOW]
Function dp_convert_to_count already does this check. Use it to determine
if PHY_REPEATER_CNT is a valid LTTPR count.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP2.0 requires that LT be performed with PHY_REPEATER_MODE
programmed to 0x55 (Transparent) whenever PHY_REPEATER_CNT is any value
other than 0x80, 0x40, 0x20, 0x10, 0x08, 0x04, 0x02, or 0x01.
[HOW]
Write Non-Transparent (0xAA) to PHY_REPEATER_MODE when LTTPRs detected and Non-Transparent is
requested.
Write Transparent in all other cases.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 Spec states that a DPTX shall put LTTPRs into Transparent
mode after reading LTTPR Capability registers on HPD.
The wording of the SCR is somewhat ambiguous as to whether
Transparent mode must be set explicity, or is implicitly set on LTTPR
capability read. Explicitly setting Transparent mode after LTTPR
capability read should cover all
cases.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 requires that LTTPR caps be read first on hotplug.
For the sake of consistency, this should also be the case on bootup.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want LTTPR capabilities to be readable from more places than just
retrieve_link_cap
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
A new SCR for the DP2.0 spec requires that LTTPR caps be the first thing
read from DPCD upon hotplug.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixed:
- LTTPR improvements
- Backlight improvements
- eDP hotplug detection
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To change the swizzle visual confirm reference pipe from top pipe to
bottom pipe due to bottom pipe information would be more important
for multiple overlay case.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move mst start top mgr in dc_link_detect layer.
Remove unused same_dpcd variable.
Move PEAK_FACTOR_X1000 and LINK_TRAINING_MAX_VERIFY_RETRY
to the proper header for defining dc link internal constant.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some custom platforms use eDP hotplug events to notify panel
capability changes that should be reported
[How]
Add a DC config option that unblocks eDP hotplug events
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Ability to triage DMCUB is improved with availability of certain
dmub registers not currently captured in crash dump diagnostic data.
[HOW]
Add dmub registers to diagnostic data collection.
Thanks Nicholas Kazlauskas for awesome input on this!
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
PG registers are absent in beige goby, so programming these registers
generate call trace. Fix this by adding a dummy function in dcn303
initialization function which prevents writing to non existant registers.
Fixes: cd6d421e3d ("drm/amd/display: Initial DC support for Beige Goby")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c:
3539:12-42: duplicated argument to && or ||
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c:
5677:87-123: duplicated argument to && or ||
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use ARRAY_SIZE instead of dividing sizeof array with sizeof an
element.
Clean up the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/core/dc_resource.c:448:47-48: WARNING:
Use ARRAY_SIZE.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the following includecheck warning:
./drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c: clk_mgr.h is
included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support a new visual confirm mode: swizzle to show the specific
color at the screen border according to different surface swizzle mode.
Currently we only support the Linear mode with red color.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is an assert in cases where transition from ODM 2:1
to ODM 1:1 (bypass)
[How]
Remove assert since this case is now valid.
Update diags tests for ODM transitions.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found a use case (IPKVM) that DP-VGA active dongle does
not return any EDID and the mentioned commit broke it.
[How]
This reverts "Disconnect non-DP with no EDID"
Signed-off-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When calculating recout width for an MPO plane on a mode that's using
ODM combine, driver can calculate a negative value, resulting in a
crash.
[How]
For negative widths, use zero such that validation will prune the
configuration correctly and disallow MPO.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For DCN30 and later, there is no data in DML arrays indexed by state at
index num_states.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DISPCLK_MAX_ERRDET_CYCLES must be 7 to prevent connection loss when
changing DENTIST_DISPCLK_WDIVIDER from 126 to 127 and back.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence that requires access to these
registers.
v2: squash in DCN3.1 fixes (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence which requires access to the FIFO
ERRDET SW Override register.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Rearranging pipes with multiple displays and multiple planes cannot be
done atomically and requires a much improved sequence to deal with it.
[How]
To workaround such issues, prefer avoid pipe-split policy for
multidisplay scenarios.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS overrides training link training parameters
for MST device to SST mode, MST resources are not
released and leak of the resource may result crash and
incorrect MST discovery during following hot plugs.
[how]
Retaining sink object to be reused by SST link and
releasing MST resources.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow specifying which panel to take PSR Residency
measurements from.
[how]
Pass panel instance to DMUB through GPINT in the upper
8 bits of the parameter.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add support for transmitting training pattern sequences for links whose
encoders have been dynamically assigned.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP equalization phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change was found to break some high-refresh modes. Reverting
to unblock mainline.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently there is no way to visually identify if there is one or more
layers presented fullscreen on the display
[HOW]
Add new visual confirm colors in get_surface_visual_confirm_color for
planes with layer_index > 0
Signed-off-by: Evgenii Krasnikov <Evgenii.Krasnikov@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This disablement would be specific for Nav10 and shouldn’t be propagated to the other programs.
[How]
Power gating is controlled by driver.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSCCLK validation is not necessary because DSCCLK is derrived from
DISPCLK, therefore if DISPCLK validation passes, DSCCLK is valid, too.
Doing DSCLK validation in addition to DISPCLK leads to modes being
wrongly rejected when DSCCLK was incorrectly set outside of DML.
[how]
Remove DSCCLK validation because it's implicitly validated under DISPCLK
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DCC on/off, stutter period is calculated before DCC has fully transitioned.
This results in incorrect stutter period calculation.
[How]
Trigger a full update when DCC changes between on/off.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two spelling mistakes in dml_print messages, fix these and
clear up checkpatch warning on overly wide line length.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the following includecheck warning:
./drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:
dce110_hw_sequencer.h is included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Port the necessary changes from previous DCN versions.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Container for hardware resources and blocks for DCN3.1, also adds
new DC debug flags used with DCN3.1.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCUB has a deferred z10 restore process that needs signalling from
driver to occur. This needs to be done on any interface that programs
the hardware state or sequences where we expect to have the same
hardware state as before.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN3.1 specific hardware sequence programming - extending off of
our existing DCN3/DCN2 support.
Extend stream hardware sequencing to include new DCCG programming.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updated interfaces for multiple eDP backlight caps.
Added support for interpreting the new BIOS command tables on DCN3.1.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New DTM interface is V3 and we need to extend our existing support
to enable HDCP on DCN3.1.
Version the helpers and fallback to the older versions on failure
in the new interfaces.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The PANEL block handles embedded panel power and backlight programming.
This programming and sequencing is now owned by DMCUB and driver will
call into the interface for backlight status and programming.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU-B (Display Micro-Controller Unit B) is a display microcontroller
used for shared display functionality with BIOS and for advanced
power saving display features.
Extends the command header to include new DCN3.1 functionality.
Adds new interfaces to DC dmub interface as well for z-state support.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Extends off of DCN3.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML (Display mode library) is used for calculating watermarks, bandwidth
and for validating display configurations.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for programming the DCN3.1 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
There are no changes to OPP or MPC for DCN3.1, so the diagram will
include them in this patch.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3.1 which controls
legacy HDMI/DP stream/link encoding.
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Includes some updates to core logic for link encoder assignment and
future support for new high bandwidth output.
v2: squash in unused variable fix (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing on AMD Carizzo with DCE-11.0 display engine showed that
it doesn't like a 36 bpp linebuffer very much. The display just
showed a solid green.
Testing on RavenRidge DCN-1.0, Polaris11 with DCE-11.2 and Kabini
with DCE-8.3 did not expose any problems, so for now only revert
to 30 bpp linebuffer depth on asics with DCE-11.0 display engine.
Fixes: a316db7209 ("drm/amd/display: Increase linebuffer pixel depth to 36bpp.")
Reported-by: Tom StDenis <Tom.StDenis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable active_disp is being initialized with a value that
is never read, it is being re-assigned immediately afterwards.
Clean up the code by removing the need for variable active_disp.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Local variable 'i' and 'j' will be initialized in the for loop, so
remove the redundant initialization.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to avoid warnings with linebuffer depth 36 bpp.
Testing on a Polaris11, DCE-11.2 on a 10 bit HDR-10 monitor
showed no obvious problems, and this 12 bpc limit is consistent
with what other function in the DCE bit depth reduction path use.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing with the photometer shows that at least Raven Ridge DCN-1.0
does not achieve more than 10 bpc effective output precision with a
16 bpc unorm surface of type SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616,
unless linebuffer depth is increased from LB_PIXEL_DEPTH_30BPP to
LB_PIXEL_DEPTH_36BPP. Otherwise precision gets truncated somewhere
to 10 bpc effective depth.
Strangely this increase was not needed on Polaris11 DCE-11.2 during
testing to get 12 bpc effective precision. It also is not needed for
fp16 framebuffers.
Tested on DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the necessary format definition, bandwidth and pixel size mappings,
prescaler setup, and pixelformat selection, following the logic
already present for SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616.
The new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 is implemented as the
old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616 format, but with swapped
red <-> green color channel, by use of the hardware xbar.
Please note that on the DCN 1/2/3 display engines, the pixelformat
in hubp and dpp setup for the old SURFACE_PIXEL_FORMAT_GRPH_ARGB16161616
and the new SURFACE_PIXEL_FORMAT_GRPH_ABGR16161616 was changed from
format id 22 to id 26. See amd/include/navi10_enum.h for the meaning
of the id's.
For format 22, the display engine read the framebuffer in 16 bpc format,
but truncated to the 12 bpc actually supported by later pipeline stages.
However, the engine took the 12 LSB of each color component for
truncation, which is incompatible with rendering at least under Vulkan,
where content is 16 bit wide, and a 12 MSB alignment would be appropriate,
if any. Format 20 for ARGB16161616_12MSB does work, but even better, we
can choose format 26 for ARGB16161616_UNORM, keeping all 16 bits around
until later stages of the display pipeline.
This allows to directly consume what the rendering hw produces under
Vulkan for swapchain format VK_FORMAT_R16G16B16A16_UNORM, as tested
with a patched version of the current AMD open-source amdvlk driver
which maps swapchain format VK_FORMAT_R16G16B16A16_UNORM onto
DRM_FORMAT_XBGR16161616.
The old id 22 would cause colorful pixeltrash to be displayed instead.
Tested under DCN-1.0 and DCE-11.2.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:929:6: warning: no previous prototype for ‘dce110_edp_wait_for_T12’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:29:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: note: (near initialization for ‘mi_shifts.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: note: (near initialization for ‘mi_masks.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:264:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:29:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7270:45: note: (near initialization for ‘mi_shifts.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:657:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_sh_mask.h:7269:43: note: (near initialization for ‘mi_masks.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:159:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:265:2: note: in expansion of macro ‘MI_GFX6_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:662:3: note: in expansion of macro ‘MI_DCE6_MASK_SH_LIST’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:927:6: warning: no previous prototype for ‘dce110_edp_wait_for_T12’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/gpio_service.c: In function ‘dal_gpio_service_create’:
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/gpio_service.c:71:4: warning: implicit conversion from ‘enum dce_version’ to ‘enum dce_environment’ [-Wenum-conversion]
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/gpio_service.c:77:4: warning: implicit conversion from ‘enum dce_version’ to ‘enum dce_environment’ [-Wenum-conversion]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_outbox.c:30: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: expecting prototype for get_ss_info_from_table(). Prototype was for get_ss_info_from_tbl() instead
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1562: warning: expecting prototype for BiosParserObject(). Prototype was for bios_parser_get_ss_entry_number() instead
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1739: warning: expecting prototype for get_ss_entry_number_from_internal_ss_info_table_V3_1(). Prototype was for get_ss_entry_number_from_internal_ss_info_tbl_V3_1() instead
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper2.c:141: warning: expecting prototype for translate_transmitter_bp_to_atom2(). Prototype was for dal_cmd_table_helper_transmitter_bp_to_atom2() instead
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper.c:127: warning: expecting prototype for translate_transmitter_bp_to_atom(). Prototype was for dal_cmd_table_helper_transmitter_bp_to_atom() instead
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3ca402375a.
Recent visual confirm changes are regressing the driver, causing a
black screen on boot in some green sardine configs, or visual confirm
is not updated at all.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.137 brings improvements in multiple areas.
In summary, we highlight:
- Updates on DP configurations and clock recovery API
- Improvements on DSC, link training sequence, etc.
- Fixes on memory leak, ODM scaling, etc.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two issues with scaling calculations, odm recout
calculation and matching viewport to actual recout.
This change fixes both issues. Odm recout calculation via
special casing and viewport matching issue by reworking
the viewport calcualtion to use scaling ratios and recout
to derrive the required offset and size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
1. move 8b 10 link trianing into its own function
2. make link status check after a link success link as part of
dp transition to video idle sequence.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As recommended by DP specs, source needs to make sure
DPRX exits previous LT mode before configuring new LT params
Nofity what channel coding mode we will use for current link training.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Start using INBOX0 for HW Lock command
[How]
- Implement initial interface for INBOX0 HW lock message
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP clock recovery phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Update application of training settings for links whose encoders are
assigned dynamically.
- Add functionality useful for DP link configuration to public
interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
OS uses older flip model which does not work with desktop
VRR causing memory allocations at the wrong IRQ level.
[HOW]
Checks added to flip model to verify model is 2.2 or greater when
doing any of the desktop VRR checks for full updates. This
prevents full updates when VRR changes until a mode change.
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Added support for individual control for multiple back-light instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Function 'dc_power_down_on_boot' is declared twice, remove the
repeated declaration.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bandwidth calculations are triggered for non zero streams, and
in case of 0 streams, these calculations were skipped with
pstate status not being updated.
[How]
As the pstate status is applicable for non zero streams, check
added for allowing 0 streams inline with dcn internal bandwidth
validations.
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable displaying DPM levels for VCN clocks
in swsmu supported ASICs
v2: removed set functions for navi, renoir
v3: removed set function from arcturus
v4: added missing defines in drm_table and remove
uneeded goto label in navi10_ppt.c
Signed-off-by: David M Nieto <david.nieto@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Conditions that end up modifying the global dc state must be locked.
However, during mst allocate payload sequence, lock is already taken.
With StarTech 1.2 DP hub, we get an HPD RX interrupt for a reason other
than to indicate down reply availability right after sending payload
allocation. The handler again takes dc lock before calling the
dc's HPD RX handler. Due to this contention, the DRM thread which waits
for MST down reply never gets a chance to finish its waiting
successfully and ends up timing out. Once the lock is released, the hpd
rx handler fires and goes ahead to read from the MST HUB, but now its
too late and the HUB doesnt lightup all displays since DRM lacks error
handling when payload allocation fails.
[How]
Take lock only if there is a change in link status or if automated test
pattern bit is set. The latter fixes the null pointer dereference when
running certain DP Link Layer Compliance test.
Fixes: c8ea79a8a2 ("drm/amd/display: NULL pointer error during compliance test")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.14-2021-05-19:
amdgpu:
- Aldebaran updates
- More LTTPR display work
- Vangogh updates
- SDMA 5.x GCR fixes
- RAS fixes
- PCIe ASPM support
- Modifier fixes
- Enable TMZ on Renoir
- Buffer object code cleanup
- Display overlay fixes
- Initial support for multiple eDP panels
- Initial SR-IOV support for Aldebaran
- DP link training refactor
- Misc code cleanups and bug fixes
- SMU regression fixes for variable sized arrays
- MAINTAINERS fixes for amdgpu
amdkfd:
- Initial SR-IOV support for Aldebaran
- Topology fixes
- Initial HMM SVM support
- Misc code cleanups and bug fixes
radeon:
- Misc code cleanups and bug fixes
- SMU regression fixes for variable sized arrays
- Flickering fix for Oland with multiple 4K displays
UAPI:
- amdgpu: Drop AMDGPU_GEM_CREATE_SHADOW flag.
This was always a kernel internal flag and userspace use of it has always been blocked.
It's no longer needed so remove it.
- amdkgd: HMM SVM support
Overview: https://patchwork.freedesktop.org/series/85562/
Porposed userspace: https://github.com/RadeonOpenCompute/ROCT-Thunk-Interface/tree/fxkamd/hmm-wip
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520031258.231896-1-alexander.deucher@amd.com
[Why&How]
MALL requires idle optimizations to be enabled. This enables MALL
feature on dcn303
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This update was made for DCN30, but it is needed for DCN303 as well
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
* Add MIT license to all new files as SPDX tag.
* Fix copyright year
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual confirm will indicate if driver is programming
the surface address.
Refactor is required because much of the visual confirm
logic is buried deep in the mpcc files.
In addition, visual confirm is not updated during fast updates.
[How]
In order to have visual confirm for driver flips, visual confirm
needs to be updated on every frame, including fast updates.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
v2: drop unused variable (Alex)
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As per spec, DCN3.x can do 6:1 downscaling and DCN2.x can do 4:1. The
max downscaling limit value for DCN2.x is 250, which means it's
calculated as 1000 / 4 = 250. For DCN3.x this then gives 1000 / 6 = 167.
[how]
Set maximum downscaling limit to 167 for DCN3.x
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP version and DPCD revision are different. Per VESA
spec, "The DPCD revision for eDP v1.4 is 13h".
SUPPORTED_LINK_RATES is valid since eDP v1.4 (DPCD_REV_13).
[How]
Correct DPCD_REV for eDP v1.4.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some small modes (<200pixels) the stutter period is really big and will cause
overflow. In these cases we shouldnt try to enable MALL as it will exceeds range
of hysteresis timer (this can be seen in some IGT tests where the
plane size is small)
[How]
Compare the stutter_period with the frame time and if we will overflow
there is no point in trying to enable MALL (and see the ASSERT) so we
early exist in this case
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some lttpr configuration steps are exclusive to 8b/10b channel
coding mode. We need to take channel conding into account.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Acked-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The function's name doesn't represent what it actaully does.
The function implements necessary steps for our hardware to
transition from link training mode back to video idle mode.
Therefore, rename the function as dp_transition_to_video_idle
so everyone can understand it.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Rename initialize_training_settings to decide_training_settings.
Call get link encoding format and decide training settings
based on current channel coding.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Implement a function that determines link encoding format
based on the link settings passed in.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Active DP dongles return no EDID when dongle
is connected, but VGA display is taken out.
Current driver behavior does not remove the
active display when this happens, and this is
a gap between dongle DTP and dongle behavior.
[How]
For active DP dongles and non-DP scenario,
disconnect sink on detection when no EDID
is read due to timeout.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Improve readability and maintainability of code.
[How]
Refactor test pattern size calculation out of function
call parameter and store value in variable.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the investigation on how to add visual confirmation on top of the
planes used by DCN, it becomes evident that the lack of information in
the code makes this work unnecessarily complicated. This commit
introduces a set of documentation related to the RECOUT operation in
order to make it easy for developers to navigate this set of functions.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To improve the code readability, this commit removes a set of commented
and not used functions for a long time. Notice that now we have the
amdgpu_dm_dtn_log, which prints all the relevant information that we
need.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit introduces kernel documentation to some essential functions
related to power gate control over planes. It also adds a macro to make
one part of the code easy to understand.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to get current DMUB time.
[How]
Add get_current_time interface to dmub_srv.
v2: drop whitespace changes (Alex)
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous patch caused crash and had been reverted. This patch
addresses the issue without regression.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This function is not used anywhere, remove it. It was added in
40dd6bd376 ("drm/amd/display: Linux Set/Read link rate and lane count
through debugfs") and moved in fe798de53a ("drm/amd/display: Move link
functions from dc to dc_link"), but a user is missing.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now the flag simply selects memory config 0 when flag is true
however 420 modes benefit more from memory config 3.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some pipe harvesting configs, we will select the incorrect
dpp_inst when programming DTO. This is because when any intermediate
pipe is fused, resource instances are no longer in 1:1
correspondence with pipe index.
[How]
When looping through pipes to program DTO, get the dpp_inst
associated with each pipe from res_pool.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DSC tests fail because stream pixel encoding does not change
its value according to the type requested in the DPCD test params.
[How]
Set stream pixel encoding before updating DSC config and configuring
the test pattern.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, the code that fills the clock table can miss filling
information about some of the higher voltage states advertised
by the SMU. This, in turn, may cause some of the higher pixel clock
modes (e.g. 8k60) to fail validation.
[How]
Fill the table with one entry per DCFCLK level instead of one entry
per FCLK level. This is needed because the maximum FCLK does not
necessarily need maximum voltage, whereas DCFCLK values from SMU
cover the full voltage range.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
The change includes some dp link training refactors:
1. break down is_ch_eq_done to checking individual conditions in
its own function.
2. update dpcd_set_training_pattern to take in dc_dp_training_pattern
as input.
3. moving lttpr mode struct definition into link_service_types.h
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DETBufferSizeInKByte is not expected to be sub-dividable, hence
unsigned int is a better suited data-type. Change it to an array
as well to satisfy current requirements.
[How]
Change the data-type of DETBufferSizeInKByte to an unsigned int
array. Modify the all the variables like DETBufferSizeY,
DETBufferSizeC that are involved in DETBufferSizeInKByte calculations
to unsigned int in all the display_mode_vba_xx files.
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP link training to public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling a DisplayPort stream:
- Optionally reducing link bandwidth between failed link training
attempts should progressively relax training requirements.
- Abandoning link training altogether if a sink is unplugged should
avoid unnecessary training attempts.
[How]
- Add fallback parameter to DP link training function and reduce link
bandwidth between failed training attempts as long as stream bandwidth
requirements are met.
- Add training status for sink unplug and abort training when this
status is reported.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some links are dynamically assigned link encoders on stream enablement.
[How]
Update DisplayPort training parameter determination stage that assumes
link encoder statically assigned to link.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some extra provisions are required during DPRX detection for links which
lack physical HPD and AUX/DDC pins.
[How]
Avoid attempting to access nonexistent physical pins during DPRX
detection.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings improvements across DP, eDP, DMUB, DSC, etc
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hardware need to be reset, driver need to reset stream objects but
dc_resource_state_destruct function omit resetting stream_count. It will
lead page fault if some logic will touch stream object.
[How]
Set stream_count to 0 when dc_resource_state_destruct.
Signed-off-by: Paul Wu <paul.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DP specification, YCbCr420 shall use VSC SDP.
[How]
For YCbCr420 timings, fail DP mode timing validation
if DPCD caps do not indicate VSC SDP colorimetry
support.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sometimes, such as sleep wake, the link->local sink pointer changed,
but the dc_stream_state->sink pointer is not changed. The checking
of timing_changed reports wrong result, lead to link tear down
unexpected wrongly.
[How]
SST compare local sink, MST compare proper remote link.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DP spec, for active protocol convertor adaptor, DP source should enable audio
for DFP type is DP, HDMI or DP++. Current is_dp_active_dongle() checking is not
precise, which treat branch device default as active dongle. As a result, we will
mistakenly disable audio for DFP type is DP case.
[How]
Make is_dp_active_dongle() checking more precise for active dongle types.
Rename active diongle type as SST branch device in case confusion.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[How]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) DM will retrieve Outbox1 message and send back reply to upper layer
and complete the AUX command
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The split pipe config is updated due to antoher stream bandwidth
validataion. Driver doesn't reprogram the split pipe config
to signle pipe cause SW use signel pipe but HW still use pipe split.
[How]
track global updates and update any hw that isn't
related to current stream being updated.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "dc: treat memory as a single-channel for
asymmetric memory".
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Based on hardware team recommendation this additional dsc overhead
is only required for DP DSC.
[how]
Add a check for is_dp and only apply the overhead if this flag is set.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two declarations of struct dc_state here.
Remove the later duplicate more secure.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In commit 482812d566 ("drm/amd/display: Set max TTU on
DPG enable"), "hubp.h" was added which caused the duplicate include.
To be on the safe side, remove the later duplicate include.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP 1.4a spec mandates that if DP_EXTENDED_RECEIVER_CAP_FIELD_PRESENT is
set, Extended Base Receiver Capability DPCD space must be used. Without
doing that, the three DPCD values that differ will be wrong, leading to
incorrect or limited functionality. MST link rate, for example, could
have a lower value. Also, Synaptics quirk wouldn't work out well when
Extended DPCD was not read, resulting in no DSC for such hubs.
[how]
Modify MST topology manager to use the values from Extended DPCD where
applicable.
To prevent regression on the sources that have a lower maximum link rate
capability than MAX_LINK_RATE from Extended DPCD, have the drivers
supply maximum lane count and rate at initialization time.
This also reverts commit 2dcab875e7 ("Revert drm/dp_mst: Retrieve
extended DPCD caps for topology manager"), brining the change back to the
original commit ad44c03208 ("drm/dp_mst: Retrieve extended DPCD caps for
topology manager").
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429221151.22020-2-nikola.cornij@amd.com
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] New platform. Need to add corresponding register control
Signed-off-by: Max.Tseng <Max.Tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As hardware team suggested that we need to add a max dsc bw overhead
into existing stream bandwidth when DSC is used.
The formula as below:
max_dsc_bw_overhead =
v_addressable * slice_count * 256 bit * pixel clock / v_total / h_total
effective stream bandwidth = pixel clock * bpp
stream bandwidth = effective stream bandwidth + dsc stream overhead
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems there's a typo to set MASTER_UPDATE_LOCK_DB_EN when disable
doublebuffer lock.
[How]
Clear MASTER_UPDATE_LOCK_DB_EN when disable doublebuffer lock
Signed-off-by: Robin Chen <robin.chen@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Add register for programming in new platform
Signed-off-by: Max.Tseng <Max.Tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CLK mgr is null for server settings.
[How]
Guard the function with NULL check.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
ABM assumes only 1 eDP is connected. Refactored existing
ABM interface to support multiple instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
to initial ddc structure before we use them to avoid error checking.
[HOW]
add 0 as structure initialization value in DCN resource construct
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver program dpp clock calculate by pipe split config but hw config is single pipe.
[How]
Skip programming clock when allow seamless boot.
After porgramming pipe config, seamless boot flag will be clear.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change only fix dpp clock switch to lower case.
New solution later can fix both case, which is "dc: skip
program clock when allow seamless boot"
[How]
This reverts commit "dc: wait vblank when stream enabled
and update dpp clock"
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
New minor revision needs to be handled
[HOW]
Add switch case and assert to catch missing switch cases in the future
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some MST devices uses different method to enable mst
specific stream features.
[How]
Add dm_helpers_mst_enable_stream features. This can be
modified later when we are ready to implement those features.
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
When a monitor does not set both QS and QY bits, DC does not
set Q0, Q1, QY0 and QY1 bits in AVI infoframe. Setting RGB bits
should be separate from setting YCC bits.
[How?]
Separate logic for setting RGB and YCC quantization range bits
in the AVI infoframe.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How & Why]
Changed "prsent" to "present".
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add logs to verify ILR optimization behaviour on boot
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
While Link Training is being performed,
and the LTTPRs are in Non-LTTPR or LTTPR Transparent mode,
any DPCD registers besides those used for Link Training are not to be
accessed.
The spec defines the link training registers as DP_TRAINING_PATTERN_SET
(102h) to DP_TRAINING_LANE3_SET (106h), and DP_LANE0_1_STATUS (202h)
to DP_ADJUST_REQUEST_LANE2_3 (207h).
[HOW]
Move the current write to DPCD Address DP_LINK_TRAINING_PATTERN_SET out
of its conditional block.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should skip programming manual trigger on non-primary planes when MPO is
enabled.
[HOW]
Implement an explicit mechanism for skipping manual trigger programming
for planes that shouldn't cause the frame to end.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous change had been reverted since it caused hang.
Remake change to avoid defect.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Fixes: b8720ed0b8 ("drm/amd/display: System black screen hangs on driver load")
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found that dc_link_reallocate_mst_payload is not used anymore
in any of the use case scenario.
[How]
removed dc_link_reallocate_mst_payload function definition
and declaration.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Primary feature use case is with eDP panels.
[How]
Fail seamless boot validation if display is not an eDP panel.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We want to immediately fail seamless boot validation if DSC is active,
as VBIOS currently does not support DSC timings. Add a check for
the relevant flag in dc_validate_seamless_boot_timing.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.131 brings improvements in multiple areas.
In summary, we highlight:
-Enhancement for multiple eDP BL control.
-Add debug flag to enable eDP ILR by default and debugfs to repress HPD/HPR_RX IRQ.
-Fixes for DSC enable sequence,Force vsync flip,hang when psr is enabled etc.
-Firmware releases:
0.0.60
0.0.61
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SKIP_CRTC_DISABLE bit should be applicable to all dcn asics
not only Raven.
[How]
Replace check for Raven only with check for all DCNs.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Driver currently assumes only 1 eDP is connected. Added support for
multiple eDP BL control.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When boot into OS, seamless boot device won't blank stream.
Driver update dpp clock when scanline position in vactive will show
garbage on screen.
[How]
Wait for vblank for seamless boot edp display when driver update dpp clock.
The apply seamless boot flag will be clear when OS call SetVisibility on.
Therefore we only wait for vblank once after boot into OS.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
Connecting clock optimization functions to dcn301 HWSS
to enable power state enter/exit optimization
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Removing unused DSC flag which is incorrect and is not used.
We are only using stream->timing.flags.DSC for DSC's current
state. Stream state as an input parameter and should not contain
any past status flags.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow observed when disabling PIP overlay in-game when
vsync is disabled, due to OTC master lock not working with
game pipe which is immediate flip.
[How]
When performing a full update, override flip_immediate value
to false for all planes, so that flip occurs on vsync.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If no repeaters are found, we do not need or want to attempt to
link-train repeaters, as this could cause bugs.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're always validating DML with simple 422 DSC even if native 422 DSC
is in use.
[How]
Use the mode configuration from the timing.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC is enabled before reset link and potentially cause DSC enable fail problem.
[How]
Enable DSC after link is reseted
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS currently sets the max link rate found in eDP 1.4 SUPPORTED_LINK_RATES table
If eDP fastboot optimizations are enabled, the link rate remains at max after init
[How]
Determine optimal link rate during boot, disable seamless boot
and eDP fastboot optimizations if link rate optimization is required
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Allow per-asic enablement of ILR feature with debug flag
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Update SR Exit Latency to fix screen flickering caused due to OTG
underflow. This is the recommended value given by the hardware IP team.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.130 brings improvements in multiple areas.
In summary, we highlight:
- Firmware release 0.0.59
- Fixes on display experiences for 4k TVs, register mask missing, etc.
- Enhancements on MST, code cleaning and debug messages.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Pipe input DSC bpc has a type mismatch with maximum DSC
input bpc - align the maximum with the pipe input type,
unsigned integer.
When checking the type we shoudl also check for an
implicit value of 0 and align with what the spreadsheet
does - default to max.
Rename output_bpc to dsc_input_bpc to reflect what the
field is actually used for.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN3 is not reusing DCN1 mask_sh_list, causing
SURFACE_FLIP_INT_MASK missing in the mapping.
[How]
Add the corresponding entry to DCN3 list.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
Due to compiler optimization the values would be
passed to the division function uninitialized
causing a div by zero. Initialize the numerator
and denominator to 0 and 1 to prevent division
by zero.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently to view the DCC_EN bit the entire DTN log
must be dumped. A compact method to view the DCC_EN
bit is desirable.
[how]
Introduce new debugfs interface that only dumps the
DCC_EN bit.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dcc_en
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add debug flag for an option to disable min fclk.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add debug prints for SMU messages with regard to
versions, clocks, and more.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Robin Singh <Robin.Singh@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to keep track of the number of eDP links to
properly enumerate edp panel control instance.
[How]
Added dc_edp_id_count to dc_context to keep track of
number of eDP links.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OTG_VUPDATE_KEEPOUT register and fields is
available on DCN10, and named the same in DCN20.
[How]
Move register definition and programming function
to dcn10 optc.
There is no functional change.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is case when the userspace like IGT test updates the custom
timings, i.e. the number of active lines CRTC property value,
and without committing the change, followed by
resetting the display, creating FB and plane to the pipe
and committing. The NULL pointer of pipe_ctx->plane_state
occurs and result in kernel crash. We need to avoid that.
[how]
add pointer check for the dc_plane_state of the pipe context in
the call of committing planes for stream in DC component.
Signed-off-by: Robin Singh <robin.singh@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT command to get PSR state from FW times out.
[How]
Add retry to get valid PSR state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following features/fixes:
- LTTPR improvements
- Disable MALL when SMU not present
- Fix bug in HW that causes P-State to hang when DPG is enabled in
certain conditions
- Update code path for enabling DPG
- Update display endpoint control path
- Add dynamic link encoder selection
- Fix debugfs MST topology to dump from the root MST node
- Enable DP DSC Compliance automation for Linux
- ASSR is enabled only when DPCD is supported and the display
connected is internal
- Added kernel trace event to print real-time refresh rate value
to debug VRR issues
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.
[How]
Disable MALL when SMU is not present.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There is a bug in HW that causes P-State to hang when DPG is enabled in
certain conditions.
[HOW]
The solution is to force MIN_TTU_VBLANK register to maximum value
whenever DPG has been enabled.
Make stream do a full update on test pattern change, so that the TTUs
get updated.
When DPG is enabled, update the ttu_regs.min_ttu_vblank field of each
pipe in the stream's topology to the maximum value (0xffffff).
v2: squash in build fix for when DCN is not defined (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to make enabling test pattern a part of the
stream update code path. This change is the first step
towards that goal.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be dynamically mapped to the link encoders
which drive them.
[How]
Update the code paths for display enabling/disabling to accommodate
the dynamic association between links and link encoders.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be programmably mapped to compatible link
encoders. The assignment of link encoders to links has to be dynamic to
accommodate the increased flexibility in comparison to conventional
display endpoints.
[How]
- Add link encoder assignment tracking variables.
- Execute link encoder assignment algorithm before enabling link and
release link encoders from links once they are disabled.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some systems can enable LTTPR through bits in BIOS, while other systems
can be configured at boot to enable LTTPR. Some configs enable
Non-Transparent mode, while others enable Transparent mode.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are three possible modes for LTTPR:
- Non-LTTPR mode, where AUX timeout is 400 us and no per-hop link
training is done
- LTTPR Transparent mode, where AUX timeout is 3200 us and no per-hop
link training is done
- LTTPR Non-Transparent mode, where AUX timeout is 3200 us and per-hop
link training is done
[HOW]
Use an enum instead of a bool to track LTTPR state; modify comparisons
accordingly.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The logic to toggle LTTPR transparent/non-transparent requires 2 flags
provided by BIOS
[HOW]
Repurpose the interface to get dce caps so both LTTPR querying functions
can use them.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Word "remainder" was misspelled as "reminder" in
reduceSizeAndFraction method variable.
[how]
Fix the spelling.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Alexander Deucher <alexander.deucher@amd.com>
Reviewed-by: Bindu R <Bindu.R@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Color depth data is not parsed during test requests.
[How]
Update display color depth according to color depth
request from the test equipment.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ASSR enabling only considers capability declared in DPCD.
We also need to check whether the connector is internal.
[How]
ASSR enabling need to check both DPCD capability and internal display
flag.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some platforms will have LTTPR capabilities forced on by VBIOS flags;
the functions added here will access those flags.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Link index doesn't always correspond to the appropriate eDP instance.
We can assume lower link index is a lower eDP instance and set panel
control instance accordingly.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change set_drr to pass in the entire dc_crtc_timing_adjust
structure instead of passing in the parameters individually.
This is to more easily pass in required parameters in the
adjust structure when it gets updated.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On NAVI14 CONFIG_UBSAN reported shift-out-of-bounds at
display_rq_dlg_calc_20v2.c:304:38
rq_param->misc.rq_c.blk256_height is 0 when chroma(*_c) is invalid.
dml_log2 returns -1023 for log2(0), although log2(0) is undefined.
Which ended up as:
rq_param->dlg.rq_c.swath_height = 1 << -1023
[How]
Fix applied on all dml versions.
1. Ensure dml_log2 is only called if the argument is greater than 0.
2. Subtract req128_l/req128_c from log2_swath_height_l/log2_swath_height_c
only when it is greater than 0.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When performing clock recovery, if a pre-emphasis adjustment is
requested, but voltage swing remains constant, the the retry counter
will not be reset. This can lead to prematurely failing link training.
[How]
Reset the clock recovery retry counter if an adjustment is requested
for either voltage swing or pre-emphasis.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is causing a pstate change underflow regression for
unknown reason
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to log DMCUB trace buffer events as Linux kernel traces.
[How]
Register an IRQ handler for DMCUB outbox0 interrupt in amdgpu_dm,
and log the messages in the DMCUB tracebuffer to a new DMCUB
TRACE_EVENT as soon as we receive the outbox0 IRQ from DMCUB FW.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some hardware revisions do have a max number of lines limitation
not honouring which can cause pstate switch underflow.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct
v2: squash in SI fix (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dcn2.1 socclk entries in bandwidth params are not initialized.
They are not used now, but will be needed for dml validation.
[How]
Populate socclk bw params from dpm clock table
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 098214999c added fetching of the AUX_DPHY register
values from the vbios, but it also changed the default values
in the case when there are no values in the vbios. This causes
problems with displays with high refresh rates. To fix this,
switch back to the original default value for AUX_DPHY_TX_CONTROL.
Fixes: 098214999c ("drm/amd/display: Read VBIOS Golden Settings Tbl")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1426
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Igor Kravchenko <Igor.Kravchenko@amd.com>
Cc: Aric Cyr <Aric.Cyr@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Replace GFP_KERNEL with GFP_ATOMIC as dcn20_resource_construct()
can't sleep.
Partially fixes: https://bugzilla.kernel.org/show_bug.cgi?id=212311
as dcn20_resource_construct() also calls into SMU functions which does
mutex_lock().
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c: In function ‘bw_calcs_init’:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:2726:1: warning: the frame size of 1336 bytes is larger than 1024 bytes [-Wframe-larger-than=]
v2: squash in sizeof fix
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c: In function ‘calculate_bandwidth’:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:2016:1: warning: the frame size of 1216 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:527:17: warning: no previous prototype for ‘dce80_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:565:20: warning: no previous prototype for ‘dce80_i2c_hw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:581:20: warning: no previous prototype for ‘dce80_i2c_sw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:715:22: warning: no previous prototype for ‘dce80_link_encoder_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:754:22: warning: no previous prototype for ‘dce80_clock_source_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:778:6: warning: no previous prototype for ‘dce80_clock_source_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:868:6: warning: no previous prototype for ‘dce80_validate_bandwidth’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:913:16: warning: no previous prototype for ‘dce80_validate_global’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.13-2021-03-23:
amdgpu:
- Debugfs cleanup
- Various cleanups and spelling fixes
- Flexible array cleanups
- Initial AMD Freesync HDMI
- Display fixes
- 10bpc dithering improvements
- Display ASSR support
- Clean up and unify powerplay and swsmu interfaces
- Vangogh fixes
- Add SMU gfx busy queues for RV/PCO
- PCIE DPM fixes
- S0ix fixes
- GPU metrics data fixes
- DCN secure display support
- Backlight type override
- Add initial support for Aldebaran
- RAS fixes
- Prime fixes for A+A systems
- Reset fixes
- Initial resource cursor support
- Drop legacy IO BAR requirements
- Various power fixes
amdkfd:
- MMU notifier fixes
- APU fixes
radeon:
- Debugfs cleanups
- Flexible array cleanups
UAPI:
- amdgpu: Add a new INFO ioctl interface to query video capabilities
rather than hardcoding them in userspace. This allows us to provide
fine grained asic capabilities (e.g., if a particular part is
bandwidth limited, we can limit the capabilities). Proposed userspace:
https://gitlab.freedesktop.org/leoliu/drm/-/commits/info_video_capshttps://gitlab.freedesktop.org/leoliu/mesa/-/commits/info_video_caps
- amdkfd: bump the driver version. There was a problem with reporting
some RAS features on older versions of the driver. Proposed userspace:
7cdd63475c
Danvet: A bunch of conflicts all over, but it seems to compile ... I
did put the call to dc_allow_idle_optimizations() on a single line
since it looked a bit too jarring to be left alone.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210324040147.1990338-1-alexander.deucher@amd.com
Move the function protoype to the right header and guard
the call with CONFIG_DRM_AMD_DC_DCN as DSC is only available
with DCN.
Fixes: 8c2f14c36f ("drm/amd/display: Add changes for dsc bpp in 16ths and unify bw calculations")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Dillon Varone <dillon.varone@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dwb_cm.c:220:65-70:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c:721:65-70: WARNING:
conversion to bool not needed here.
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp.c:1139:67-72: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When CONFIG_DRM_AMD_SECURE_DISPLAY is enabled, it will try
to register vertical interrupt 0 for specific task.
Currently, only dcn10 have defined relevant info for vertical interrupt
0. If we enable CONFIG_DRM_AMD_SECURE_DISPLAY for other dcn ASIC, will
get DC_IRQ_SOURCE_INVALID while calling dc_interrupt_to_irq_source() and
cause pointer errors.
[How]
Add support of vertical interrupt 0 for all dcn ASIC.
v2: squash in build fix (Alex)
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When driver disabled, we driver force the YCbCr420 to RGB,
which means some register will be changed, such as
RDPCS_PHY_DP_MPLLB_TX_CLK_DIV changed from 1 to 0
When driver re-enabled, OS will Set Mode YCbCr420 again,
which means the register RDPCS_PHY_DP_MPLLB_TX_CLK_DIV
should to be 1 again, but dmub fw can’t update the
register to 1 due to the mpll is not off
[How]
Adds an interface to disable accelerated mode bit,
which allows DM to decide to call during driver
disable/unload scenarios.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yao Wang1 <Yao.Wang1@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SOC needs to be updated to the WM set A values before validation
happens.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC patchset brings improvements in multiple areas. In summary, we
highlight:
* Add debug out when viewport too small
* use max lb for latency hiding
* System black screen hangs on driver load
* Fix UBSAN warning for not a valid value for type '_Bool'
* Fix for outbox1 ring buffer typecasting issue
* Bypass sink detect when there are no eDPs connected
* Increase precision for bpp in DSC calculations
* Add changes for dsc bpp in 16ths and unify bw calculations
* Correct algorithm for reversed gamma
* Remove MPC gamut remap logic for DCN30
* Fix typo for helpers function name
* Fix secure display lock problems
* Fix no previous prototype warning
* Separate caps for maximum RGB and YUV plane counts
* Add debugfs to control DMUB trace buffer events
* [FW Promotion] Release 0.0.56
* DCHUB underflow counter increasing in some scenarios
* fix dml prefetch validation
* fix dcn3+ bw validation soc param update sequence
* add a func to disable accelerated mode
* Fix potential memory leak
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When unplugging a display, the underflow counter can be seen to
increase because PSTATE switch is allowed even when some planes are not
blanked.
[How]
Check that all planes are not active instead of all streams before
allowing PSTATE change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not all ASICs have same plane capabilities so need to split them
out for proper support handling.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Atufa Khan <Atufa.Khan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Word "helper" was misspelled as "helpes" in
dm_helpes_dmub_outbox0_interrupt_control function.
[how]
Fix the spelling.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
Should only reroute gamut remap to mpc unless 3D LUT is not used and all
planes are using the same src->dest.
[How?]
Remove DCN30 specific logic for rerouting gamut remap to mpc.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN30 needs to correctly program reversed gamma curve, which DCN20
already has.
Also needs to fix a bug that 252-255 values are clipped.
[How]
Apply two fixes into DCN30.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Acked-by: Vladimir Stempen <Vladimir.Stempen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
Some code still expected bpp to be used in whole bits, not 16ths. dsc.c uses
redundant function now found in dc to calculate stream bandwidth from timing.
[How?]
Fix code to work with 16ths instead of whole bits for dsc bpp.
Refactor get_dsc_bandwidth to accept inputs in 16ths of a bit.
Use dc function to calculate bandwidth from timing, and make dsc bw calculation
a part of dsc.c.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
Many DSC variables and related functions use whole bits for bpp.
[How?]
Change variables and related functions to use 16ths of a bit for bpp.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How & Why]
Check DC config to determine if there are any eDPs connected. If there
are no eDPs connected, bypass sink detect when querying eDP presence.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit dbc43d5fdf
as it causes crash on driver load in some scenarios.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable max memory lb config to improve stutter efficiency and
latency hiding. Also increase max number of lb lines to be
used by dml since experiments have shown that there isnt a hard max
beyond what fits in lb.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bumping DC version for DMU FW fix
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_mpc.c:358:69-74: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable result is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
the dcn301_calculate_wm_and_dl() calculation exposed a issue
- switch to dcn30 version for now.
still need to follow up with dcn301 watermark updates version.
v2: squash in warning fix
Signed-off-by: Charles Sun <charles.sun@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Charles Sun <charles.sun@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DGPU Navi, the wm_table.nv_entries are used. These entires are not
populated for DCN301 Vangogh APU, but instead wm_table.entries are.
[How]
Use DCN21 Renoir style wm calculations.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'dce110_resource.h' included in 'dcn21_resource.c' is duplicated.
'hw_gpio.h' included in 'hw_factory_dce110.c' is duplicated.
Signed-off-by: Zhang Yunkai <zhang.yunkai@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The registers for the address of the cursor are aligned to 2KB, so all
cursor surfaces also need to be aligned to 2KB. Currently, the
provided cursor cache surface is not aligned, so we need a workaround
until alignment is enforced by the surface provider.
[How]
- round up surface address to nearest multiple of 2048
- current policy is to provide a much bigger cache size than
necessary,so this operation is safe
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Using values provided by DF for latency may cause hangs in
multi display configurations. Revert change to previous value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Panel control always programs instance 0. With multi eDP we need to
support multiple instances.
[How]
Use link index to set different instances for panel control.
Refactored LVTMA control to support multiple instances.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver get wrap around dmub trace data due to read pointer being
increased incorrectly when there are multiple interrupt
queues with very short interval
[How]
Check read/write pointer before copying data from ring buffer
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In some boot configurations we need to retrieve the currently
UEFI-set dppclk, but there was a typo in the calculation
[how]
Fix typo to make dpp_clk calculate off dpp_clk divider instead of
disp_clk
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On baco-enabled systems running virtual dal, can get set power
state when hw is not initialized
[How]
Skip DC hw part of setPowerState when hw not available
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DGPU Navi, the wm_table.nv_entries are used. These entires are not
populated for DCN301 Vangogh APU, but instead wm_table.entries are.
[How]
Use DCN21 Renoir style wm calculations.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Using values provided by DF for latency may cause hangs in
multi display configurations. Revert change to previous value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It just spams the logs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We set up the parameters, but never called the atom table.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:181:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: note: (near initialization for ‘aux_mask.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hdcp_i2c_offsets[] array did not have an entry for
HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one
read overflow. I added an entry and copied the 0x0 value for the offset
from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c.
I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX
entries. This doesn't change the code, but it's just a belt and
suspenders approach to try future proof the code.
Fixes: 4c283fdac0 ("drm/amd/display: Add HDCP module")
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp_cm.c:298:33-38:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Synchronization displays with different timings feature uses
reminder of 64 bit division (modulus operator) , which is not
supported by 32 bit platforms
[how]
Use div64 API for 64 bit modulus
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Bindu Ramamurthy<bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Synchronization displays with different timings feature uses division
operator for 64 bit division, which is not supported by 32 bit platforms
[how]
Use div64 API for 64 bit division
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Bindu Ramamurthy<bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
HSplit should not affect DSC slice count. Can cause improper timings to
be applied for certain modes.
[How?]
No longer change DSC Slice count based on HSplit.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating. Add additional delay
time for single rank dimm.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DMUB FW send trace event via outbox0 interrupt. Driver will handle it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPINT timeout is causing PSR_STATE_0 to be returned when it shouldn't.
We must guarantee that PSR is fully disabled before doing hw programming
on driver-side.
[How]
Return invalid state if GPINT command times out. Let existing retry
logic send the GPINT until successful.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Some existing DC interfaces are optimized to return a single eDP
link/stream. Refactored those DC interfaces to support multiple eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the creation of link encoder objects is tightly coupled to the
creation of link objects. Decoupling link encoder object creation is a
preliminary step in the process of allowing link encoders to be
dynamically assigned to links.
[How]
Add "minimal" link encoder objects which are not associated with any
link until required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[HOW]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) As the driver holds dal and dc locks while waiting for CV, the outbox1
ISR is registered with noMutexWait set to true, which allows ISR to run
and signal CV. This sets a constraint on ISR to not modify variables
such as dc, dmub, etc.
4) Created dmub_outbox.c with dmub_enable_outbox_notification() to enable
outbox1 mailbox.
5) New mailbox address ranges allocated for outbox1 of size DMUB_RB_SIZE.
Created dmub functions for Outbox1: dmub_dcn20_setup_out_mailbox(),
dmub_dcn20_get_outbox1_wptr() and dmub_dcn20_set_outbox1_rptr().
6) Added functions dc_stat_get_dmub_notification() and
dmub_srv_stat_get_notification() to retrieve Outbox1 message.
7) Currently, DMUB doesn't opens DDC in AUX mode before issuing AUX
transaction. A workaround is added in dce_aux_transfer_dmub_raw() to
open in DDC in AUX mode for every AUX transaction.
8) Added dc debug option enable_dmub_aux_for_legacy_ddc enable/disable
DMUB AUX. This debug option is checked dce_aux_transfer_with_retries()
to select the method to process AUX transactions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dce/dmub_psr.c:273:16-21: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dcn30/dcn30_dpp_cm.c:243:67-72:
WARNING: conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables ASSR if display declares such support in DPCD.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/core/dc_link_ddc.c:544:34-39: WARNING:
conversion to bool not needed here.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Spatial dithering to 10 bpc depth was disabled for all DCE's.
Testing on DCE-8.3 and DCE-11.2 did not show any obvious ill
effects, but a measureable precision improvement (via colorimeter)
when displaying a fp16 framebuffer to a 10 bpc DP or HDMI connected
HDR-10 monitor.
v2: enable it for all DCEs (Alex)
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com> (v2)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, this function is called when DIG BE is not
connected to DIG FE, in which case a value of zero isn't
invalid and assert should not be hit.
[How]
Remove assert and handle ENGINE_ID_UNKNOWN result in calling
function.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
No reason to have uninitialized var at top of function
[How]
Move it to minimum scope where it's actuallty used
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a window of time where we optimize bandwidth due to no streams
enabled will enable PSTATE changing but HUBPs are not disabled yet.
This results in underflow counter increasing in some hotplug scenarios.
[How]
Set the optimize-bandwidth flag for later processing once all the HUBPs
are properly disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vendor based fan noise improvement
[how]
Report timing synchronizable when DP streams time frame
difference is less than 0.05 percent. Adjust DP DTOs and
sync displays using MASTER_UPDATE_LOCK_DB_X_Y
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some external displays with DP can use seamless boot, but their audio endpoints are
only enabled after hotplug.
On boot, these displays inherit UEFI timings without properly initializing audio.
[How]
Enable display audio when seamless booting with an external monitor over DP.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot over DP MST is not POR, but is not explicitly disabled.
[How]
Add check for DP MST and return false in
dc_validate_seamless_boot_timing.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases, this function is called when DIG BE is not
connected to DIG FE, in which case a value of zero isn't
invalid and assert should not be hit.
[How]
Remove assert and handle ENGINE_ID_UNKNOWN result in calling
function.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New proposed sequence for HUBP blanking causes regressions where the
hardware would fail to enter blank which triggers an assert in the new
sequence. This change brings back the old sequence.
Fixes: 985faf2c4e ("drm/amd/display: New sequence for HUBP blank")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.123 brings improvements in multiple areas.
In summary, we highlight:
- Firmware release 0.0.52
- Bug fixes on MPC OGAM sequence, display experience, etc.
- Improvements on timing, transmitter control, etc.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving definition of transmitter control from atomfirmware
to internal header.
[How]
Update the command table code to call 1.7 and make it the
default fallback path.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Simplify AVMUTE logic in coding
[How]
Avoid multiple calls on TMDS AVMUTE
as updated logic now demands it.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With certain fclock overclocks, state 1 may be chosen
as the closest clock level. This may result in this state
being empty if not populated beforehand, resulting in
black screens and screen corruption.
[How]
Copy over all soc states to clock_limits before bounding
box creation to avoid any cases with empty states.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If system is overclocked, only 1 bounding box state will
be sent by SMU. This results in an empty state being copied
for DML calculations causing black screens and corruption.
[How]
Fully populate bounding box before duplicating last state.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Color corruption can occur on bootup into a login
manager that applies a non-linear gamma LUT because
the LUT may not actually be powered on before writing.
It's cleared on the next full pipe reprogramming as
we switch to LUTB from LUTA and the pipe accessing
the LUT has taken it out of light sleep mode.
[How]
The MPCC_OGAM_MEM_PWR_FORCE register does not force
the current power mode when set to 0. It only forces
when set light sleep, deep sleep or shutdown.
The register to actually force power on and ignore
sleep modes is MPCC_OGAM_MEM_PWR_DIS - a value of 0
will enable power requests and a value of 1 will
disable them.
When PWR_FORCE!=0 is combined with PWR_DIS=0 then
MPCC OGAM memory is forced into the state specified
by the force bits.
If PWR_FORCE is 0 then it respects the mode specified
by MPCC_OGAM_MEM_LOW_PWR_MODE if the RAM LUT is not
in use.
We set that bit to shutdown on low power, but otherwise
it inherits from bootup defaults.
So for the fix:
1. Update the sequence to "force" power on when needed
We can use MPCC_OGAM_MEM_PWR_DIS for this to turn on the
memory even when the block is in bypass and pending to be
enabled for the next frame.
We need this for both low power enabled or disabled.
If we don't set this then we can run into issues when we
first program the LUT from bootup.
2. Don't apply FORCE_SEL
Once we enable power requests with DIS=0 we run into the
issue of the RAM being forced into light sleep and being
unusable for display output. Leave this 0 like we used to
for DCN20.
3. Rely on MPCC OGAM init to determine light sleep/deep sleep
MPC low power debug mode isn't enabled on any ASIC currently
but we'll respect the setting determined during init if it
is.
Lightly tested as working with IGT tests and desktop color
adjustment.
4. Change the MPC resource default for DCN30
It was interleaving the dcn20 and dcn30 versions before
depending on the sequence.
5. REG_WAIT for it to be on whenever we're powering up the
memory
Otherwise we can write register values too early and we'll
get corruption.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We added these in DMCUB for runtime feature detection
but we didn't have helpers to call these with DC error
handling/logging.
[How]
Add helpers.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware team remeasured, need to update timings
to increase latency slightly and avoid intermittent
underflows.
[How]
sr exit latency update.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit fd1c85d3ac
[Why]
We are not implementing the planned new HW sequence
to disable HUBP.
[How]
Revert most related changes to minimize possibility
of regression.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit f8e792dc5c
[Why]
We are not implementing the planned new HW
sequence for HUBP disable.
[How]
Revert most related changes to minimize regressions.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In following sequence driver will add counter twice on
same edp stream.
1. Boot into OS.
2. Set timing with edp only.
3. Set timing with edp and external monitor.
4. Set visibility on for edp.
Step 2 and 3 will add seamless boot counter twice and
subtract it once in step 4.
[How]
Remove global counter and calculate it is used.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To get the pixel statistics on every frame, change ABM
sample rate from 2 to 1.
[How]
Change LS, HS and BL sample rate to 1.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn21_validate_bandwidth() calls functions that use floating point math.
On my machine this sometimes results in simd exceptions when there are
other FPU users such as KVM virtual machines running. The screen freezes
completely in this case.
Wrapping the function with DC_FP_START()/DC_FP_END() seems to solve the
problem. This mirrors the approach used for dcn20_validate_bandwidth.
Tested on a AMD Ryzen 7 PRO 4750U (Renoir).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206987
Signed-off-by: Jan Kokemüller <jan.kokemueller@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix potential integer overflow by casting actual_calculated_clock_100hz
to u64, in order to give the compiler complete information about the
proper arithmetic to use.
Notice that such variable is used in a context that expects
an expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
actual_calculated_clock_100hz * post_divider
Fixes: 7a03fdf628 ("drm/amd/display: fix 64bit division issue on 32bit OS")
Addresses-Coverity-ID: 1501691 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4a3dea8932.
This causes blank screens for some users.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1388
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Jun Lei <Jun.Lei@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This version brings along following fixes:
- Fix error handling in dc/dcn10/dcn10_hw_sequencer_debug.c
- DIO Supported for virtual displays
- memset dmub_rb_cmd to 0 which fixes issues talking with firmware
- fix 64bit division issue on 32bit OS
- move edp sink present detection to hw init to fix hang
- reverts a patch that caused 3x4K60 displays over MST
with DSC enabled to not light up
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is possible for ret_vsnprintf to be assigned negative value in
error cases. As an unsigned variable, negative values which
are stored in their 2's complement form gets treated as a positive
number. This will led to treating bad cases as good ones.
eg: -1 gets stored as 0xFFFFFFFF on a 32 bit system
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual displays do not use the backend of the pipe, and so have
infinite backend bandwidth.
[HOW]
Add a skip_dio_check bool to the VBA struct, which is used to override
the DIOSupport calculations.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Chris Park <Chris.Park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since dmub_rb_cmds are not initialized to 0,
the header is filled with invalid data.
This is causing issues on the fw side.
[How]
Initialize dmub_rb_cmd unions to 0.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace "/" with div_u64 for 64bit division on 32bit OS.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
At SW init, we may not be ready to do detect eDP sink.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
3x4K60 displays over MST with DSC enabled was not able to light up
due to this patch.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
VBIOS program DIG_CLK_PATTERN using engine ID instead of PHY ID.
Workaround by writing value for 0x1f (for HDMI) after calling vbios.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
On DCN1.0, need otg vertical line interrupt to get appropriate timing
to achieve specific feature request.
Add otg vertical interrupt0 support for registers which operation is
vertical sensitive.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Better handling of dummy p-state table
- Workaround for some legacy DP-VGA dongles
- Add Freesync HDMI support to DMCU
- Enable "trigger_hotplug" debugfs on all outputs
- fix initial bounding box values for dcn3.02
- implement support for DID2.0 dsc passthrough
- fix calculation for the pwl backlight curve
- Fix multiple memory leaks
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Overlay won't move to a new positon if viewport size is smaller than
what can be handled. It'd either disappear or stay at the old
position. This condition is for example hit if overlay is moved too
much outside of left or top edge of the screen, but it applies to
any non-cursor plane type.
[how]
Reject this contidion at validation time. This gives the calling
level a chance to handle this gracefully and avoid inconsistent
behaivor.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some scenarios where we use a UCLK frequency in between dummy p-state table
entries result in a p-state hang, due to the table not having a close
enough match, so the default DPM0 latency is used, which can be too long to
support dummy p-state switching in these scenarios.
[How]
- old: match if current freq is within +- margin of table entry
- new: find largest table entry that is lower than current freq + margin
- lower than DPM0 will still use DPM0
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Maximum resolution is 1440*900 when connecting to FHD monitor via some DP-VGA
dongles. The display EDID reading fails over AUX/I2C via DP->VGA dongle, and
this leads to the maximum resolution 1920*1080 cannot be obtained from EDID.
[How]
Provide a workaround for some legacy DP-VGA dongles with a longer aux delay.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Remove force_ignore_link_settings debug option as it is no longer used.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Adding support for Freesync HDMI to DC and DMCU
[How]
Create DC interface and implementation on top of DMCU to support
parsing CEA blocks in DMCU.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initial bounding box values are updated in dcn30_update_bw_bounding_box
but they use dcn3_0_soc and dcn3_0_ip instead of dcn3_02_soc and
dcn3_02_ip
[How]
Add dcn302_update_bw_bounding_box and
dcn302_get_optimal_dcfclk_fclk_for_uclk so it uses
dcn3_02_soc and dcn3_02_ip.
Use sr_exit_time_us, sr_enter_plus_exit_time_us,
from dcn30 on dcn302 to fix flicker on eDP.
Also use dram_clock_change_latency_us from dcn30.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels contain active converters (e.g. DP to MIPI) which only support
restricted DSC configurations. DID2.0 adds support for such displays to
explicitly define per timing BPP restrictions on DSC. Ignoring these
restrictions leads to blackscreen.
[How]
Add parsing in DID2.0 parser to get this bpp info.
Add support in DSC module to constraint target bpp based
on this info.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC update brings improvements in multiple areas. In summary, we highlight:
- Fix display detection on HDMI ComboPHY
- Drop SOC bounding box hookup
- Fix DPCD values
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When enabling HDMI on ComboPHY, there are not
enough clock sources to complete display detection.
[HOW]
Initialize more clock sources.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In HDCP update stream config interface, some variables are named as
xxx_supported, but in fact the variable indicates whether or not xxx_enabled.
Correct the naming so it is less confusing to read the code.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In seamless boot without a flip case, the flag power_gated didn't
get cleared when resetting path mode because the plane_state is null.
The following sequence will cause this issue:
1. OS call set mode to clone/extended
2. Reset path mode to remove edp
[How]
Set power gated default to true in seamless boot pipe
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we discard the current context and recreate it. The current
context is what is applied to the HW so we should be re-using this
rather than creating a new context.
Recreating the context can lead to mismatch between new context and the
current context
For example: gsl groups get changed when we create a new context this
can cause issues in a multi display config (with flip immediate) because
we don't align the existing gsl groups in the new and current context.
If we reuse the current context the gsl group assignment stays the same.
[How]
Instead of discarding the current context, we instead just copy the
current state and add/remove planes and streams.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Safeguarding as pointer may be null in diagnostic environment
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some dcnxxx__resource.c do not initialize the i2c speed; this patch adds
the required initialization at dc_construct().
Signed-off-by: Brendan Steve Leder <brendanSteve.Leder@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The translation between the DPCD value and the specified AUX_RD_INTERVAL
in the DP spec do not match.
[How]
Update values to match the spec.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There aren't any ASIC where we use these binaries and they aren't
useful for future use since it's inconvenient to extend and maintain
these structures.
[How]
Drop the support from DM and DC for now.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:3137:35-40:
WARNING: conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Suggested-by: Yang Li <oswb@linux.alibaba.com>
Signed-off-by: Abaci Team <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes corrupted display output in HDMI deep color
10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3.
It will hopefully also provide fixes for other DCE's up to
DCE-11, assuming those will need similar fixes, but i could
not test that for HDMI due to lack of suitable hw, so viewer
discretion is advised.
dce110_stream_encoder_hdmi_set_stream_attribute() is used for
HDMI setup on all DCE's and is missing color_depth assignment.
dce110_program_pix_clk() is used for pixel clock setup on HDMI
for DCE 6-11, and is missing color_depth assignment.
Additionally some of the underlying Atombios specific encoder
and pixelclock setup functions are missing code which is in
the classic amdgpu kms modesetting path and the in the radeon
kms driver for DCE6/DCE8.
encoder_control_digx_v3() - Was missing setup code wrt. amdgpu
and radeon kms classic drivers. Added here, but untested due to
lack of suitable test hw.
encoder_control_digx_v4() - Added missing setup code.
Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color
output at 10 bpc and 12 bpc.
Note that encoder_control_digx_v5() has proper setup code in place
and is used, e.g., by DCE-11.2, but this code wasn't used for deep
color setup due to the missing cntl.color_depth setup in the calling
function for HDMI.
set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon
kms. Added here, but untested due to lack of hw.
set_pixel_clock_v6() - Missing setup code added. Successfully tested
on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI
deep color output with 10 bpc or 12 bpc.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010
and COLOR_DEPTH_121212 cases directly contradict the code comment which
explains how this should work, whereas the COLOR_DEPTH_888 case
is consistent with the code comments. Comment says the bitmask should
be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but
the implementation contradicts that: 10 bit case sets a mask for 12 bpc
clamping, whereas 12 bit case sets a mask for 14 bpc clamping.
Note that during my limited testing on DCE-8.3 (HDMI deep color)
and DCE-11.2 (DP deep color), this didn't have any obvious ill
effects, neither did fixing it change anything obvious for the
better, so this fix may be inconsequential on DCE, and just
reduce the confusion of innocent bystanders when reading the code
and trying to investigate problems with 10 bpc+ output.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang warns about the -mhard-float command line arguments
on architectures that do not support this:
clang: error: argument unused during compilation: '-mhard-float' [-Werror,-Wunused-command-line-argument]
Move this into the gcc-specific arguments.
Fixes: e77165bf7b ("drm/amd/display: Add DCN3 blocks to Makefile")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The debug printk dereferences "link->link_enc" before we have ensured
that it is non-NULL. Fix this potential NULL derefence by moving the
printk after the check.
Fixes: 64ff088242 ("drm/amd/display: Log link/connector info provided in BIOS object table")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace "/" with div_u64 for 32-bit OS. On 32-bit OS,
the use of "/" for 64-bit division will cause build error,
i.e. "__udivdi3/__divdi3 undefined!".
Fixes: ea7154d8d9 ("drm/amd/display: Update dcn30_apply_idle_power_optimizations() code")
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 57eeaf47a6.
Original issue of flash line when MPO enabled on idle screen
was fixed by raising clocks. This had negative effect of extra
power being drained. With the upstream commit 9d03bb1020
("drm/amd/display: disable dcn10 pipe split by default")
flash line issue was fixed and had positive effect for
battery life. Hence this patch is no more required.
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warnings:
./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c:
1009:6-16: WARNING: Assignment of 0/1 to bool variable.
./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c:
200:2-10: WARNING: Assignment of 0/1 to bool variable.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two spelling mistakes of the function name, fix this
by using __func__ instead of a hard coded name string.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the function for idle optimizations
-remove hardcoded size
-enable no memory-request case
-add cursor copy
-update mall eligibility check case
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we use the maximum possible cursor cache size when deciding if we
should attempt to enable MALL, but this prevents us from enabling the
feature for certain key use cases.
[How]
- consider cursor bpp when calculating if the cursor fits
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-Uncomment watermark set d
-This populates the wm table so that it can be sent to PMFW
-This watermark table is used when we are in mall stutter
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When no displays are currently enabled, display driver should not
disallow PSTATE switching.
[How]
Allow PSTATE switching if either the active configuration supports it,
or there are no active displays.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
dml20v2_ModeSupportAndSystemConfigurationFull() didn't check against
DesiredBPP, so it doesn't work correctly when DesiredBPP can't be satisfied.
How:
Port the TruncToValidBPP() version from display_mode_vba_21.c to
display_mode_vba_20v2.c.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Add logging statements to assist in debugging
errors in the BIOS object table.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
Function decide_dp_link_settings() loops infinitely when required bandwidth
can't be supported.
How:
Check the required bandwidth against verified_link_cap before trying to
find a link setting for it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the BIOS table is invalid or corrupt then get_i2c_info can fail
and we dereference a NULL pointer.
[How]
Check that ddc_pin is not NULL before using it and log an error if it
is because this is unexpected.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
These can differ per ASIC or not be present. Don't call the dcn20 ones
directly but rather the ones defined by the ASIC init table.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previously as MPO + ODM Combine was not supported, finding secondary pipes
for each case was mutually exclusive. Now that both are supported at the same
time, both cases should be taken into account when finding a secondary pipe.
[HOW]
If a secondary pipe cannot be found based on previous bottom pipe,
search for a second pipe using next_odm_pipe instead.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FEC over eDP support is incomplete.
[How]
Disable FEC over eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Heavy corruption or blank screen reported on wake,
with 6k display connected and FEC enabled
[how]
When Disable/Enable stream for display pipes on HPDRX,
DC should take into account ODM split pipes.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Follow the coding style of size of a struct, changing to:
p = kmalloc(sizeof(*p), ...);
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The buffer is allocated with the size of pointer and copy with the size of
data structure. Then trigger the system memory page fault. Use the
orignal data structure to get the object size.
Fixes: 3a00c04212 ("drm/amd/display/dc/core/dc_link: Move some local data from the stack to the heap")
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jinzhou.Su <Jinzhou.Su@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn20/display_mode_vba_20.c:3141:30-39:
WARNING: Comparison to bool
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn21/display_mode_vba_21.c:5121:14-38:
WARNING: Comparison to bool
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dcn10/dcn10_dpp_cm.c:580:23-31:
WARNING: Comparison to bool
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:1228:9-20:
WARNING: Comparison to bool
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:214: warning: Function parameter or member 'link' not described in 'dc_link_detect_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:350: warning: Function parameter or member 'link' not described in 'dc_link_is_dp_sink_present'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:841: warning: Function parameter or member 'link' not described in 'dc_link_detect_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:841: warning: Function parameter or member 'reason' not described in 'dc_link_detect_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:3403: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1710: warning: Function parameter or member 'old_stream' not described in 'dc_is_stream_unchanged'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1710: warning: Function parameter or member 'stream' not described in 'dc_is_stream_unchanged'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1726: warning: Function parameter or member 'old_stream' not described in 'dc_is_stream_scaling_unchanged'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1726: warning: Function parameter or member 'stream' not described in 'dc_is_stream_scaling_unchanged'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1843: warning: Function parameter or member 'dc' not described in 'dc_add_stream_to_ctx'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1843: warning: Function parameter or member 'new_ctx' not described in 'dc_add_stream_to_ctx'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1843: warning: Function parameter or member 'stream' not described in 'dc_add_stream_to_ctx'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1870: warning: Function parameter or member 'dc' not described in 'dc_remove_stream_from_ctx'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1870: warning: Function parameter or member 'new_ctx' not described in 'dc_remove_stream_from_ctx'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1870: warning: Function parameter or member 'stream' not described in 'dc_remove_stream_from_ctx'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:287: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:366: warning: Function parameter or member 'crc_window' not described in 'dc_stream_configure_crc'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:430: warning: Function parameter or member 'r_cr' not described in 'dc_stream_get_crc'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:430: warning: Function parameter or member 'g_y' not described in 'dc_stream_get_crc'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:430: warning: Function parameter or member 'b_cb' not described in 'dc_stream_get_crc'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2026: warning: Function parameter or member 'dc' not described in 'dc_check_update_surfaces_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2026: warning: Function parameter or member 'updates' not described in 'dc_check_update_surfaces_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2026: warning: Function parameter or member 'surface_count' not described in 'dc_check_update_surfaces_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2026: warning: Function parameter or member 'stream_update' not described in 'dc_check_update_surfaces_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2026: warning: Function parameter or member 'stream_status' not described in 'dc_check_update_surfaces_for_stream'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2822: warning: Function parameter or member 'dc' not described in 'dc_interrupt_set'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2822: warning: Function parameter or member 'src' not described in 'dc_interrupt_set'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2822: warning: Function parameter or member 'enable' not described in 'dc_interrupt_set'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2962: warning: Function parameter or member 'link' not described in 'dc_link_add_remote_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2962: warning: Function parameter or member 'edid' not described in 'dc_link_add_remote_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2962: warning: Function parameter or member 'len' not described in 'dc_link_add_remote_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2962: warning: Function parameter or member 'init_data' not described in 'dc_link_add_remote_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3022: warning: Function parameter or member 'link' not described in 'dc_link_remove_remote_sink'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3022: warning: Function parameter or member 'sink' not described in 'dc_link_remove_remote_sink'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It looks like it could be used inside the DC_TRACE_LEVEL_MESSAGE() macro.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c: In function ‘dpcd_set_source_specific_data’:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:4403:18: warning: variable ‘result_write_min_hblank’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c: In function ‘dc_link_construct’:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:1588:1: warning: the frame size of 1176 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:1115:23: warning: no previous prototype for ‘dce60_create_resource_pool’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:1312:23: warning: no previous prototype for ‘dce61_create_resource_pool’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:1505:23: warning: no previous prototype for ‘dce64_create_resource_pool’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:1126:23: warning: no previous prototype for ‘dce80_create_resource_pool’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:1325:23: warning: no previous prototype for ‘dce81_create_resource_pool’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:1520:23: warning: no previous prototype for ‘dce83_create_resource_pool’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:29:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_8_0_sh_mask.h:9546:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:213:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:102:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:305:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_8_0_sh_mask.h:9546:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:213:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:102:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce80/dce80_resource.c:305:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_8_0_sh_mask.h:9545:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:213:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:102:2: note: in expansion of macro ‘AUX_SF’
NB: Snipped lots for the sake of brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:28:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_d.h:568:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:155:14: note: in expansion of macro ‘mmCRTC0_DCFE_MEM_LIGHT_SLEEP_CNTL’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.h:170:2: note: in expansion of macro ‘SRI’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:181:3: note: in expansion of macro ‘XFM_COMMON_REG_LIST_DCE60’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:185:3: note: in expansion of macro ‘transform_regs’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_d.h:568:43: note: (near initialization for ‘xfm_regs[0].DCFE_MEM_LIGHT_SLEEP_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:155:14: note: in expansion of macro ‘mmCRTC0_DCFE_MEM_LIGHT_SLEEP_CNTL’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.h:170:2: note: in expansion of macro ‘SRI’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:181:3: note: in expansion of macro ‘XFM_COMMON_REG_LIST_DCE60’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:185:3: note: in expansion of macro ‘transform_regs’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_6_0_d.h:645:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:155:14: note: in expansion of macro ‘mmCRTC1_DCFE_MEM_LIGHT_SLEEP_CNTL’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.h:170:2: note: in expansion of macro ‘SRI’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:181:3: note: in expansion of macro ‘XFM_COMMON_REG_LIST_DCE60’
NB: Snipped lots for the sake of brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:54:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:537:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:537:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:542:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:542:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:547:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:547:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:551:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:551:2: note: in expansion of macro ‘DCE10_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:889:16: warning: no previous prototype for ‘dce100_add_stream_to_ctx’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:916:16: warning: no previous prototype for ‘dce100_validate_plane’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:925:24: warning: no previous prototype for ‘dce100_find_first_free_match_stream_enc_for_link’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:1156:23: warning: no previous prototype for ‘dce100_create_resource_pool’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:54:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_10_0_sh_mask.h:5084:45: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:170:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:291:2: note: in expansion of macro ‘MI_GFX8_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:537:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_10_0_sh_mask.h:5084:45: note: (near initialization for ‘mi_shifts.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:170:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:291:2: note: in expansion of macro ‘MI_GFX8_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:537:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_10_0_sh_mask.h:5083:43: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:170:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:291:2: note: in expansion of macro ‘MI_GFX8_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:542:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_10_0_sh_mask.h:5083:43: note: (near initialization for ‘mi_masks.GRPH_NUM_BANKS’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:155:28: note: in expansion of macro ‘GRPH_CONTROL__GRPH_NUM_BANKS_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:170:2: note: in expansion of macro ‘SFB’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_mem_input.h:291:2: note: in expansion of macro ‘MI_GFX8_TILE_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:542:3: note: in expansion of macro ‘MI_DCE8_MASK_SH_LIST’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:806:6: warning: no previous prototype for ‘apply_ctx_interdependent_lock’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:883:6: warning: no previous prototype for ‘dce112_validate_bandwidth’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:1008:16: warning: no previous prototype for ‘dce112_add_stream_to_ctx’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:1407:23: warning: no previous prototype for ‘dce112_create_resource_pool’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:3710:19: warning: no previous prototype for ‘linkRateInKHzToLinkRateMultiplier’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c: In function ‘dpcd_set_source_specific_data’:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:4403:18: warning: variable ‘result_write_min_hblank’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c: In function ‘query_hdcp_capability’:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:599:28: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1120:5: warning: no previous prototype for ‘shift_border_left_to_dst’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:1131:6: warning: no previous prototype for ‘restore_border_left_from_dst’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:299:10: warning: no previous prototype for ‘generic_reg_get’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:307:10: warning: no previous prototype for ‘generic_reg_get2’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:317:10: warning: no previous prototype for ‘generic_reg_get3’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:329:10: warning: no previous prototype for ‘generic_reg_get4’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:343:10: warning: no previous prototype for ‘generic_reg_get5’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:359:10: warning: no previous prototype for ‘generic_reg_get6’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:377:10: warning: no previous prototype for ‘generic_reg_get7’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:397:10: warning: no previous prototype for ‘generic_reg_get8’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:503:6: warning: no previous prototype for ‘generic_write_indirect_reg’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:511:10: warning: no previous prototype for ‘generic_read_indirect_reg’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:529:10: warning: no previous prototype for ‘generic_indirect_reg_get’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:560:10: warning: no previous prototype for ‘generic_indirect_reg_update_ex’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Noah Abradjian <noah.abradjian@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:2753: warning: Function parameter or member 'vbios' not described in 'is_display_configuration_supported'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:2753: warning: Function parameter or member 'calcs_output' not described in 'is_display_configuration_supported'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'ctx' not described in 'bw_calcs'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'dceip' not described in 'bw_calcs'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'vbios' not described in 'bw_calcs'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'pipe' not described in 'bw_calcs'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'pipe_count' not described in 'bw_calcs'
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3030: warning: Function parameter or member 'calcs_output' not described in 'bw_calcs'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c: In function ‘calculate_bandwidth’:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:109:18: warning: variable ‘v_filter_init_mode’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c: In function ‘bw_calcs’:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:3031:21: warning: variable ‘sclk_lvl’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:253: warning: Function parameter or member 'pStream' not described in 'dc_optimize_timing_for_fsft'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:253: warning: Function parameter or member 'max_input_rate_in_khz' not described in 'dc_optimize_timing_for_fsft'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:270: warning: Function parameter or member 'stream' not described in 'dc_stream_set_cursor_attributes'
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:270: warning: Function parameter or member 'attributes' not described in 'dc_stream_set_cursor_attributes'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_surface.c:119: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:522:17: warning: no previous prototype for ‘dce60_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:560:20: warning: no previous prototype for ‘dce60_i2c_hw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:576:20: warning: no previous prototype for ‘dce60_i2c_sw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:710:22: warning: no previous prototype for ‘dce60_link_encoder_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:749:22: warning: no previous prototype for ‘dce60_clock_source_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:773:6: warning: no previous prototype for ‘dce60_clock_source_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:863:6: warning: no previous prototype for ‘dce60_validate_bandwidth’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_resource.c:908:16: warning: no previous prototype for ‘dce60_validate_global’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:54:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:614:22: warning: no previous prototype for ‘dce100_link_encoder_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:653:32: warning: no previous prototype for ‘dce100_opp_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:668:17: warning: no previous prototype for ‘dce100_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:706:20: warning: no previous prototype for ‘dce100_i2c_hw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:721:22: warning: no previous prototype for ‘dce100_clock_source_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:745:6: warning: no previous prototype for ‘dce100_clock_source_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:834:6: warning: no previous prototype for ‘dce100_validate_bandwidth’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce100/dce100_resource.c:879:16: warning: no previous prototype for ‘dce100_validate_global’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce60/dce60_timing_generator.c:192:6: warning: no previous prototype for ‘dce60_configure_crc’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_transform_v.c:228: warning: bad line: void
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_transform_v.c:233: warning: Function parameter or member 'xfm_dce' not described in 'program_overscan'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_transform_v.c:233: warning: Function parameter or member 'data' not described in 'program_overscan'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:266:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: note: (near initialization for ‘stream_enc_regs[0].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:266:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:267:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: note: (near initialization for ‘stream_enc_regs[1].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:267:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:268:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:262:15: note: (near initialization for ‘stream_enc_regs[2].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:268:2: note: in expansion of macro ‘stream_enc_regs’
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:66:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:276:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:276:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:276:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:276:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:553:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:553:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:553:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:553:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:557:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:557:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:557:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:557:3: note: in expansion of macro ‘HWSEQ_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:594:3: note: in expansion of macro ‘MI_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:594:3: note: in expansion of macro ‘MI_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:599:3: note: in expansion of macro ‘MI_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:599:3: note: in expansion of macro ‘MI_DCE11_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:718:17: warning: no previous prototype for ‘dce110_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:756:20: warning: no previous prototype for ‘dce110_i2c_hw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:771:22: warning: no previous prototype for ‘dce110_clock_source_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:795:6: warning: no previous prototype for ‘dce110_clock_source_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:1037:16: warning: no previous prototype for ‘dce110_validate_plane’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:1092:16: warning: no previous prototype for ‘dce110_validate_global’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:1336:29: warning: no previous prototype for ‘dce110_resource_cap’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:66:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_0_sh_mask.h:5936:51: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:116:16: note: in expansion of macro ‘DIG_FE_CNTL__DIG_STEREOSYNC_SELECT__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:306:2: note: in expansion of macro ‘SE_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_0_sh_mask.h:5936:51: note: (near initialization for ‘se_shift.DIG_STEREOSYNC_SELECT’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:116:16: note: in expansion of macro ‘DIG_FE_CNTL__DIG_STEREOSYNC_SELECT__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:306:2: note: in expansion of macro ‘SE_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_0_sh_mask.h:5938:52: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:116:16: note: in expansion of macro ‘DIG_FE_CNTL__DIG_STEREOSYNC_GATE_EN__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.h:307:2: note: in expansion of macro ‘SE_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_resource.c:272:3: note: in expansion of macro ‘SE_COMMON_MASK_SH_LIST_DCE110’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_0_sh_mask.h:5938:52: note: (near initialization for ‘se_shift.DIG_STEREOSYNC_GATE_EN’)
NB: Snipped for brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:1034:6: warning: no previous prototype for ‘dce110_mem_input_v_construct’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator_v.c:54: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_v_enable_crtc'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator_v.c:216: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_v_wait_for_vactive'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:620:22: warning: no previous prototype for ‘dce112_link_encoder_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:674:32: warning: no previous prototype for ‘dce112_opp_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:689:17: warning: no previous prototype for ‘dce112_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:727:20: warning: no previous prototype for ‘dce112_i2c_hw_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:742:22: warning: no previous prototype for ‘dce112_clock_source_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:766:6: warning: no previous prototype for ‘dce112_clock_source_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:1027:16: warning: no previous prototype for ‘dce112_validate_global’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:1205:29: warning: no previous prototype for ‘dce112_resource_cap’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_compressor.c:429:14: warning: no previous prototype for ‘controller_id_to_index’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:79: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:124: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_enable_crtc'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:179: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:233: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_disable_crtc'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:258: warning: Function parameter or member 'tg' not described in 'program_horz_count_by_2'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:258: warning: Function parameter or member 'timing' not described in 'program_horz_count_by_2'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:284: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_program_timing_generator'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:284: warning: Function parameter or member 'dc_crtc_timing' not described in 'dce110_timing_generator_program_timing_generator'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:356: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:525: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:561: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1118: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_validate_timing'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1118: warning: Function parameter or member 'timing' not described in 'dce110_timing_generator_validate_timing'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1118: warning: Function parameter or member 'signal' not described in 'dce110_timing_generator_validate_timing'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1174: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_wait_for_vblank'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1198: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_wait_for_vactive'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1208: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1386: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1768: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1801: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_disable_vga'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1851: warning: Function parameter or member 'tg' not described in 'dce110_timing_generator_set_overscan_color_black'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1851: warning: Function parameter or member 'color' not described in 'dce110_timing_generator_set_overscan_color_black'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1851: warning: Excess function parameter 'param' description in 'dce110_timing_generator_set_overscan_color_black'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:602:13: warning: ‘dce120_timing_generator_get_position’ defined but not used [-Wunused-function]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:471:6: warning: no previous prototype for ‘dce_mem_input_v_is_surface_pending’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:486:6: warning: no previous prototype for ‘dce_mem_input_v_program_surface_flip_and_addr’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:563:6: warning: no previous prototype for ‘dce_mem_input_v_program_pte_vm’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:636:6: warning: no previous prototype for ‘dce_mem_input_v_program_surface_config’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:922:6: warning: no previous prototype for ‘dce_mem_input_v_program_display_marks’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:945:6: warning: no previous prototype for ‘dce_mem_input_program_chroma_display_marks’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:966:6: warning: no previous prototype for ‘dce110_allocate_mem_input_v’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_mem_input_v.c:1008:6: warning: no previous prototype for ‘dce110_free_mem_input_v’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:1639: warning: Function parameter or member 'dc' not described in 'dce110_enable_accelerated_mode'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_hw_sequencer.c:1639: warning: Function parameter or member 'context' not described in 'dce110_enable_accelerated_mode'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_compressor.c:415:6: warning: no previous prototype for ‘dce110_get_required_compressed_surfacesize’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c: In function ‘dce110_timing_generator_tear_down_global_swap_lock’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce110/dce110_timing_generator.c:1354:12: warning: variable ‘value_crtc_vtotal’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Aric Cyr <Aric.Cyr@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Tony Cheng <Tony.Cheng@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10480:62: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:96:16: note: in expansion of macro ‘FMT_BIT_DEPTH_CONTROL__FMT_TEMPORAL_DITHER_EN__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:114:2: note: in expansion of macro ‘OPP_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:148:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_COMMON_BASE’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:321:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_112’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10480:62: note: (near initialization for ‘opp_shift.FMT_TEMPORAL_DITHER_EN’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:96:16: note: in expansion of macro ‘FMT_BIT_DEPTH_CONTROL__FMT_TEMPORAL_DITHER_EN__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:114:2: note: in expansion of macro ‘OPP_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:148:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_COMMON_BASE’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:321:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_112’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10479:60: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:96:16: note: in expansion of macro ‘FMT_BIT_DEPTH_CONTROL__FMT_TEMPORAL_DITHER_EN_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:114:2: note: in expansion of macro ‘OPP_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:148:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_COMMON_BASE’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:325:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_112’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10479:60: note: (near initialization for ‘opp_mask.FMT_TEMPORAL_DITHER_EN’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:96:16: note: in expansion of macro ‘FMT_BIT_DEPTH_CONTROL__FMT_TEMPORAL_DITHER_EN_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:114:2: note: in expansion of macro ‘OPP_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.h:148:2: note: in expansion of macro ‘OPP_COMMON_MASK_SH_LIST_DCE_COMMON_BASE’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This file uses a complex abstracted set of hierarchical macros to
setup its applicable register lists within constant structures.
However in the case of TMDS_CNTL we wish to mark it as not applicable
for this use-case.
One method would be to de-const all of the definitions and users, then
manually zero out TMDS_CNTL from the list. Another would be to create
a new set of hierarchical macros to omit TMDS_CNTL entirely. Both
would entail a great deal of unnecessary changes and maintenance
burden.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:290:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[0].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:290:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:291:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[1].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:291:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:292:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[2].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:292:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:293:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[3].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:293:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:294:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[4].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:294:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:295:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:286:15: note: (near initialization for ‘stream_enc_regs[5].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:295:2: note: in expansion of macro ‘stream_enc_regs’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:59:
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10014:58: note: (near initialization for ‘aux_shift.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE__SHIFT’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:177:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce112/dce112_resource.c:181:2: note: in expansion of macro ‘DCE_AUX_MASK_SH_LIST’
drivers/gpu/drm/amd/amdgpu/../include/asic_reg/dce/dce_11_2_sh_mask.h:10013:56: note: (near initialization for ‘aux_mask.AUX_SW_AUTOINCREMENT_DISABLE’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:214:16: note: in expansion of macro ‘AUX_SW_DATA__AUX_SW_AUTOINCREMENT_DISABLE_MASK’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.h:127:2: note: in expansion of macro ‘AUX_SF’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:602:13: warning: ‘dce120_timing_generator_get_position’ defined but not used [-Wunused-function]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:73: warning: Cannot understand *****************************************************************************
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:593: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:426:32: warning: no previous prototype for ‘dce120_opp_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:440:17: warning: no previous prototype for ‘dce120_aux_engine_create’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:478:20: warning: no previous prototype for ‘dce120_i2c_hw_create’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This file uses a complex abstracted set of hierarchical macros to
setup its applicable register lists within constant structures.
However in the case of TMDS_CNTL we wish to mark it as not applicable
for this use-case.
One method would be to de-const all of the definitions and users, then
manually zero out TMDS_CNTL from the list. Another would be to create
a new set of hierarchical macros to omit TMDS_CNTL entirely. Both
would entail a great deal of unnecessary changes and maintenance
burden.
Instead, let's just silence the warning.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:281:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[0].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:281:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:282:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[1].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:282:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:283:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[2].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:283:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:284:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[3].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:284:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:285:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[4].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:285:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:286:2: note: in expansion of macro ‘stream_enc_regs’
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:277:15: note: (near initialization for ‘stream_enc_regs[5].TMDS_CNTL’)
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_resource.c:286:2: note: in expansion of macro ‘stream_enc_regs’
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:101:6: warning: no previous prototype for ‘dce120_timing_generator_validate_timing’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:128:6: warning: no previous prototype for ‘dce120_tg_validate_timing’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:136:6: warning: no previous prototype for ‘dce120_timing_generator_enable_crtc’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:156:6: warning: no previous prototype for ‘dce120_timing_generator_set_early_control’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:169:10: warning: no previous prototype for ‘dce120_timing_generator_get_vblank_counter’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:184:6: warning: no previous prototype for ‘dce120_timing_generator_get_crtc_position’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:210:6: warning: no previous prototype for ‘dce120_timing_generator_wait_for_vblank’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:232:6: warning: no previous prototype for ‘dce120_timing_generator_wait_for_vactive’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:245:6: warning: no previous prototype for ‘dce120_timing_generator_setup_global_swap_lock’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:282:6: warning: no previous prototype for ‘dce120_timing_generator_tear_down_global_swap_lock’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:303:6: warning: no previous prototype for ‘dce120_timing_generator_enable_reset_trigger’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:350:6: warning: no previous prototype for ‘dce120_timing_generator_disable_reset_trigger’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:370:6: warning: no previous prototype for ‘dce120_timing_generator_did_triggered_reset_occur’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:387:6: warning: no previous prototype for ‘dce120_timing_generator_disable_vga’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:428:6: warning: no previous prototype for ‘dce120_timing_generator_program_blanking’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:488:6: warning: no previous prototype for ‘dce120_timing_generator_program_blank_color’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:501:6: warning: no previous prototype for ‘dce120_timing_generator_set_overscan_color_black’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:543:6: warning: no previous prototype for ‘dce120_timing_generator_set_drr’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:602:6: warning: no previous prototype for ‘dce120_timing_generator_get_position’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:635:6: warning: no previous prototype for ‘dce120_timing_generator_get_crtc_scanoutpos’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:664:6: warning: no previous prototype for ‘dce120_timing_generator_enable_advanced_request’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:702:6: warning: no previous prototype for ‘dce120_tg_program_blank_color’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:725:6: warning: no previous prototype for ‘dce120_tg_set_overscan_color’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:752:6: warning: no previous prototype for ‘dce120_tg_is_blanked’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:773:6: warning: no previous prototype for ‘dce120_tg_set_blank’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:792:6: warning: no previous prototype for ‘dce120_tg_wait_for_state’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:809:6: warning: no previous prototype for ‘dce120_tg_set_colors’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_timing_generator.c:836:6: warning: no previous prototype for ‘dce120_timing_generator_set_test_pattern’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ideally someone should strip-out all these garbage 'if 0's.
Tempted to carry out the work myself on principle!
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce120/dce120_hw_sequencer.c:53:47: warning: ‘reg_offsets’ defined but not used [-Wunused-const-variable=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.c:50:6: warning: no previous prototype for ‘dal_hw_factory_diag_fpga_init’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:43: warning: ‘struct hw_factory’ declared inside parameter list will not be visible outside of this definition or declaration
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:6: note: previous declaration of ‘dal_hw_factory_diag_fpga_init’ was here
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:43: warning: ‘struct hw_factory’ declared inside parameter list will not be visible outside of this definition or declaration
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:6: note: previous declaration of ‘dal_hw_factory_diag_fpga_init’ was here
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:43: warning: ‘struct hw_factory’ declared inside parameter list will not be visible outside of this definition or declaration
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_factory_diag.h:30:6: note: previous declaration of ‘dal_hw_factory_diag_fpga_init’ was here
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/irq_service.c:82:31: warning: no previous prototype for ‘find_irq_source_info’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/diagnostics/hw_translate_diag.c:37:6: warning: no previous prototype for ‘dal_hw_translate_diag_fpga_init’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The header doesn't provide any additional parameter descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1104: warning: Cannot understand *****************************************************************************
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:109: warning: Function parameter or member 'opp110' not described in 'set_truncation'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:109: warning: Function parameter or member 'params' not described in 'set_truncation'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:154: warning: Function parameter or member 'opp110' not described in 'dce60_set_truncation'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:154: warning: Function parameter or member 'params' not described in 'dce60_set_truncation'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:204: warning: Function parameter or member 'opp110' not described in 'set_spatial_dither'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:204: warning: Function parameter or member 'params' not described in 'set_spatial_dither'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:308: warning: Function parameter or member 'opp110' not described in 'set_temporal_dither'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:308: warning: Function parameter or member 'params' not described in 'set_temporal_dither'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:370: warning: Function parameter or member 'opp110' not described in 'dce110_opp_set_clamping'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:370: warning: Function parameter or member 'params' not described in 'dce110_opp_set_clamping'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:430: warning: Function parameter or member 'opp110' not described in 'dce60_opp_set_clamping'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:430: warning: Function parameter or member 'params' not described in 'dce60_opp_set_clamping'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:478: warning: Function parameter or member 'opp110' not described in 'set_pixel_encoding'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:478: warning: Function parameter or member 'params' not described in 'set_pixel_encoding'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:514: warning: Function parameter or member 'opp110' not described in 'dce60_set_pixel_encoding'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:514: warning: Function parameter or member 'params' not described in 'dce60_set_pixel_encoding'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/hw_ddc.c: In function ‘set_config’:
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/hw_ddc.c:110:13: warning: variable ‘reg2’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c: In function ‘dce110_link_encoder_update_mst_stream_allocation_table’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1506:11: warning: variable ‘value0’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c: In function ‘dce_aux_transfer_raw’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:579:7: warning: variable ‘bytes_replied’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit a861736dae ("drm/amd/display: Fixed Intermittent blue screen on OLED panel")
causes power regression for many users. It seems that this change causes
the MCLK to get forced high; this creates a regression for many users
since their devices were not able to drop to a low state after this
change. For this reason, this reverts commit
a861736dae.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1407
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Naveed Ashfaq <Naveed.Ashfaq@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Roman Li <roman.li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
driver has sent PMFW VBIOSSMC_MSG_SetDisplayIdleOptimizations while SMU
still processing a previous VBIOSSMC_MSG_SetHardMinDcfclkByFreq message.
[how]
same as RN, change the time out to2s.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The initial purpose of dcn10 pipe split is to support some high
bandwidth mode which requires dispclk greater than max dispclk. By
initial bring up power measurement data, it showed power consumption is
less with pipe split for dcn block. This could be reason for enable pipe
split by default. By battery life measurement of some Chromebooks,
result shows battery life is longer with pipe split disabled.
[How]
Disable pipe split by default. Pipe split could be still enabled when
required dispclk is greater than max dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Required for DSC MST
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reverts "drm/amd/display: Revert HUBP blank behaviour for now"
- Hubp blank will fail if the pipe is locked (this is the case on
linux), so add a check to make sure pipe isn't locked, if it is then
defer the blank to post_unlock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN30 has a bug where blanking HUBP blocks pstate allow unless
HUBP_DISABLE is toggled afterwards.
[HOW]
Create a HW sequence for blanking HUBP.
1. Wait for enter VBLANK
2. Set HUBP_BLANK
3. Make sure HUBP_IN_BLANK = 1
4. Toggle HUBP_DISABLE on and off to perform soft reset
All existing calls to hubp->funcs->set_blank should be replaced with
this new sequence.
In wait_for_mpcc_disconnect, only blank the pipe being disconnected, and
leave all other pipes unmodified.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A call to BREAK_TO_DEBUGGER is triggered when powering down memory
[How]
Remove the check for GAMCOR_MEM_PWR_STATE when powering off the memory
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot stream has hw resource assigned, already. 'add' is
actually rebuild the assignment.
[How]
Swap seamless boot stream to pipe 0 (if needed) to ensure pipe_ctx
matches
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Raymond Yang <rayyang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS reboots, and panel is turned off, T12 may not be maintained.
T12 is defined as the interval between VDDC off (occurs at shutdown) and
the next VDDC on (occurs when eDP is POST-ed)
[how]
DC already tracks panel power off time. Add a DC interface which DM can
call during shutdown. Ideally this should be as late as possible during
the shutdown sequence so the extra delay is minimal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. the corrected timing to write DPCD 300h AMD signature is before
link training.
2. and VBIOS will writes correctted AMD signature by after AGESA 1.0.0,
so driver doesn't need to write DPCD 300h again to switch config.
3. there are some OLED panel will clean backlight level to 0 once
receive DPCD 300h, so we will see flicker issue at that time.
[How]
read DPCD 300h signature before write it to avoid reprogram again, if
AMD signature was writed corrected by VBIOS, driver will not reprogram
it again.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching single pipe to split pipe, the bandwidth check is just
for first pipe. The 2nd pipe with abnormal(or zero) dpp clock when pipe
ready and unlock leads the garbage on display.
[How]
Removed external increasing dpp clock check, the internal function
already loops all of pipes to check whether update dpp clock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to make enabling test pattern a part of the stream update code
path. This change is the first step towards that goal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN10 uses plane visibility to determine when to unblank HUBP; there is
no reason DCN20+ should not do the same.
[HOW]
In addition to changing the check in HWSEQ, we must change
is_pipe_tree_visible so that it checks ODM pipe topologies as well as
MPC. Since we're now checking both ODM and MPC topologies, the helper
function names have been changed to reference "parent" and "child"
instead of "top" and "bottom".
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver apply the monitor patch into global debug flag. When apply
monitor patch, fec feature will always disable.
[How]
Separate fec debug flag and monitor patch
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The stack variable "val" is potentially unpopulate it, so initialize it
with the value 0xf (indicating an invalid mux)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_dp_set_test_pattern, we assume all pipes have a stream, which
can cause null pointer dereference.
[How]
Add a null pointer check before accessing stream.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/gpio/hw_factory.c:123:6: warning: no previous prototype for ‘dal_hw_factory_destroy’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:38: warning: Function parameter or member 'raw_state' not described in 'convert_psr_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'state' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'stream' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'dmub' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'enable' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'wait' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'psr_level' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'dmub' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'link' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'psr_context' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:284: warning: Function parameter or member 'dmub' not described in 'dmub_psr_force_static'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'residency' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'psr' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'ctx' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:332: warning: Function parameter or member 'ctx' not described in 'dmub_psr_create'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:349: warning: Function parameter or member 'dmub' not described in 'dmub_psr_destroy'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c: In function ‘dce_get_16_bit_backlight_from_pwm’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c:54:11: warning: variable ‘bl_pwm_cntl’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_panel_cntl.c:53:11: warning: variable ‘pwm_period_cntl’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:342:6: warning: no previous prototype for ‘dce_i2c_sw_engine_set_speed’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:356:6: warning: no previous prototype for ‘dce_i2c_sw_engine_acquire_engine’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:400:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_channel_request’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:443:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_payload’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_hw.c:438:35: warning: no previous prototype for ‘dce_i2c_hw_engine_wait_on_operation_result’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_hw.c:505:6: warning: no previous prototype for ‘dce_i2c_hw_engine_submit_payload’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lewis Huang <Lewis.Huang@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Excess function parameter 'ssinfo' description in 'get_ss_info_from_tbl'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:391:25: warning: no previous prototype for ‘get_engine_type’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:427:6: warning: no previous prototype for ‘dce60_opp_set_clamping’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:548:6: warning: no previous prototype for ‘dce60_opp_program_bit_depth_reduction’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:571:6: warning: no previous prototype for ‘dce60_opp_program_clamping_and_pixel_encoding’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:681:6: warning: no previous prototype for ‘dce60_opp_program_fmt’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And only declare it if it's to be used.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.c:74:6: warning: no previous prototype for ‘dce_dmcu_load_iram’ [-Wmissing-prototypes]
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.c:31:
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_scaler’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:496:7: warning: variable ‘filter_updated’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_pixel_storage_depth’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:19: warning: variable ‘expan_mode’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:6: warning: variable ‘pixel_depth’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Demote the one that provides no param descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'calc_pll_cs' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'target_pix_clk_100hz' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'ref_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'post_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'fract_feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'calc_pll_cs' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'pll_settings' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'ref_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'post_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'tolerance' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'clk_src' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pll_settings' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pix_clk_params' not described in 'dce110_get_pix_clk_dividers_helper'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1200:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1239:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_mst_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1429:6: warning: no previous prototype for ‘dce60_link_encoder_dp_set_phy_pattern’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.c: In function ‘dce110_update_generic_info_packet’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_stream_encoder.c:70:11: warning: variable ‘regval’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: George Shen <george.shen@amd.com>
Cc: Eric Bernstein <eric.bernstein@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_audio.c:871:6: warning: no previous prototype for ‘dce60_aud_wall_dto_setup’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: Charlene Liu <Charlene.Liu@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2588:16: warning: no previous prototype for ‘update_slot_layout_info’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2692:16: warning: no previous prototype for ‘get_bracket_layout_record’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'id' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'id' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'info' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'id' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'object_id' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'info' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'bp' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'object' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'signal' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'id' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2588:16: warning: no previous prototype for ‘update_slot_layout_info’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2692:16: warning: no previous prototype for ‘get_bracket_layout_record’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Igor Kravchenko <Igor.Kravchenko@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper2.c:145: warning: Function parameter or member 't' not described in 'dal_cmd_table_helper_transmitter_bp_to_atom2'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/command_table_helper.c:131: warning: Function parameter or member 't' not described in 'dal_cmd_table_helper_transmitter_bp_to_atom'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'matrix' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'flt' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'buffer_size' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Excess function parameter 'param' description in 'convert_float_matrix'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw supports fp16, this is not only useful for HDR,
but also for standard dynamic range displays, because
it allows to get more precise color reproduction with
about 11 - 12 bpc linear precision in the unorm range
0.0 - 1.0.
Working fp16 scanout+display (and HDR over HDMI) was
verified on a DCE-8 asic, so i assume that the more
recent DCE-10/11 will work equally well, now that
format-specific plane scaling constraints are properly
enforced, e.g., the inability of fp16 to scale on older
hw like DCE-8 to DCE-11.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need these to support PSR on DCN302
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccinelle report:
drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c:1357:6-8:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust a jump target so that a bit of exception handling can be better
reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Return directly after a call of the function “kzalloc” failed
at the beginning.
* Delete a label which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
