[Why]
A cleaner solution, only done once on boot.
[How]
Remove previous workaround and configure an extra
vmid one time on boot
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When an riommu invalidation request come at the same time as a pipe is
disabled there can be a case where DCN cannot ACK the request if only
one VMID is setup in the inuse list.
[How]
Setup a second unused VMID will work around the issue.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing state collection functions to add some additional
registers useful for debug, and add state collection function for DC
hubbub
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a difference between our default behavior and override
behavior. For default behavior we need to decide link training settings
within specs' limitation and mandates.
For override behavior we do not need to follow all these requirements.
We are isolating override decision to its own function to maintain the
integrity of our specs compliant default behavior.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware has handed down a new sequence requiring the value of this
register be read from clk_mgr.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some DPCD addresses, notably LTTPR Capability registers, are expected to
be read all together in a single DPCD transaction. Rather than force callers to
read registers they don't need, we want to quietly extend the addresses
read, and only return back the values the caller asked for.
This does not affect DPCD writes.
[HOW]
Create an additional layer above AUX to perform 'checked' DPCD
transactions.
Iterate through an array of DPCD address ranges that are marked as being
contiguous. If a requested read falls within one of those ranges, extend
the read to include the entire range.
After DPCD has been queried, copy the requested bytes into the caller's
data buffer, and deallocate all resources used.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 requires that LTTPR caps be read first on hotplug.
For the sake of consistency, this should also be the case on bootup.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move mst start top mgr in dc_link_detect layer.
Remove unused same_dpcd variable.
Move PEAK_FACTOR_X1000 and LINK_TRAINING_MAX_VERIFY_RETRY
to the proper header for defining dc link internal constant.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support a new visual confirm mode: swizzle to show the specific
color at the screen border according to different surface swizzle mode.
Currently we only support the Linear mode with red color.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence that requires access to these
registers.
v2: squash in DCN3.1 fixes (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence which requires access to the FIFO
ERRDET SW Override register.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP equalization phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN3.1 specific hardware sequence programming - extending off of
our existing DCN3/DCN2 support.
Extend stream hardware sequencing to include new DCCG programming.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for programming the DCN3.1 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
There are no changes to OPP or MPC for DCN3.1, so the diagram will
include them in this patch.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3.1 which controls
legacy HDMI/DP stream/link encoding.
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Includes some updates to core logic for link encoder assignment and
future support for new high bandwidth output.
v2: squash in unused variable fix (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3ca402375a.
Recent visual confirm changes are regressing the driver, causing a
black screen on boot in some green sardine configs, or visual confirm
is not updated at all.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two issues with scaling calculations, odm recout
calculation and matching viewport to actual recout.
This change fixes both issues. Odm recout calculation via
special casing and viewport matching issue by reworking
the viewport calcualtion to use scaling ratios and recout
to derrive the required offset and size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP clock recovery phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Update application of training settings for links whose encoders are
assigned dynamically.
- Add functionality useful for DP link configuration to public
interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Added support for individual control for multiple back-light instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Conditions that end up modifying the global dc state must be locked.
However, during mst allocate payload sequence, lock is already taken.
With StarTech 1.2 DP hub, we get an HPD RX interrupt for a reason other
than to indicate down reply availability right after sending payload
allocation. The handler again takes dc lock before calling the
dc's HPD RX handler. Due to this contention, the DRM thread which waits
for MST down reply never gets a chance to finish its waiting
successfully and ends up timing out. Once the lock is released, the hpd
rx handler fires and goes ahead to read from the MST HUB, but now its
too late and the HUB doesnt lightup all displays since DRM lacks error
handling when payload allocation fails.
[How]
Take lock only if there is a change in link status or if automated test
pattern bit is set. The latter fixes the null pointer dereference when
running certain DP Link Layer Compliance test.
Fixes: c8ea79a8a2 ("drm/amd/display: NULL pointer error during compliance test")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual confirm will indicate if driver is programming
the surface address.
Refactor is required because much of the visual confirm
logic is buried deep in the mpcc files.
In addition, visual confirm is not updated during fast updates.
[How]
In order to have visual confirm for driver flips, visual confirm
needs to be updated on every frame, including fast updates.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
v2: drop unused variable (Alex)
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Implement a function that determines link encoding format
based on the link settings passed in.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the investigation on how to add visual confirmation on top of the
planes used by DCN, it becomes evident that the lack of information in
the code makes this work unnecessarily complicated. This commit
introduces a set of documentation related to the RECOUT operation in
order to make it easy for developers to navigate this set of functions.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP link training to public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling a DisplayPort stream:
- Optionally reducing link bandwidth between failed link training
attempts should progressively relax training requirements.
- Abandoning link training altogether if a sink is unplugged should
avoid unnecessary training attempts.
[How]
- Add fallback parameter to DP link training function and reduce link
bandwidth between failed training attempts as long as stream bandwidth
requirements are met.
- Add training status for sink unplug and abort training when this
status is reported.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some links are dynamically assigned link encoders on stream enablement.
[How]
Update DisplayPort training parameter determination stage that assumes
link encoder statically assigned to link.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DP spec, for active protocol convertor adaptor, DP source should enable audio
for DFP type is DP, HDMI or DP++. Current is_dp_active_dongle() checking is not
precise, which treat branch device default as active dongle. As a result, we will
mistakenly disable audio for DFP type is DP case.
[How]
Make is_dp_active_dongle() checking more precise for active dongle types.
Rename active diongle type as SST branch device in case confusion.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Based on hardware team recommendation this additional dsc overhead
is only required for DP DSC.
[how]
Add a check for is_dp and only apply the overhead if this flag is set.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC is enabled before reset link and potentially cause DSC enable fail problem.
[How]
Enable DSC after link is reseted
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS currently sets the max link rate found in eDP 1.4 SUPPORTED_LINK_RATES table
If eDP fastboot optimizations are enabled, the link rate remains at max after init
[How]
Determine optimal link rate during boot, disable seamless boot
and eDP fastboot optimizations if link rate optimization is required
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently to view the DCC_EN bit the entire DTN log
must be dumped. A compact method to view the DCC_EN
bit is desirable.
[how]
Introduce new debugfs interface that only dumps the
DCC_EN bit.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dcc_en
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.
[How]
Disable MALL when SMU is not present.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There is a bug in HW that causes P-State to hang when DPG is enabled in
certain conditions.
[HOW]
The solution is to force MIN_TTU_VBLANK register to maximum value
whenever DPG has been enabled.
Make stream do a full update on test pattern change, so that the TTUs
get updated.
When DPG is enabled, update the ttu_regs.min_ttu_vblank field of each
pipe in the stream's topology to the maximum value (0xffffff).
v2: squash in build fix for when DCN is not defined (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be dynamically mapped to the link encoders
which drive them.
[How]
Update the code paths for display enabling/disabling to accommodate
the dynamic association between links and link encoders.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be programmably mapped to compatible link
encoders. The assignment of link encoders to links has to be dynamic to
accommodate the increased flexibility in comparison to conventional
display endpoints.
[How]
- Add link encoder assignment tracking variables.
- Execute link encoder assignment algorithm before enabling link and
release link encoders from links once they are disabled.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change set_drr to pass in the entire dc_crtc_timing_adjust
structure instead of passing in the parameters individually.
This is to more easily pass in required parameters in the
adjust structure when it gets updated.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct
v2: squash in SI fix (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SOC needs to be updated to the WM set A values before validation
happens.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the creation of link encoder objects is tightly coupled to the
creation of link objects. Decoupling link encoder object creation is a
preliminary step in the process of allowing link encoders to be
dynamically assigned to links.
[How]
Add "minimal" link encoder objects which are not associated with any
link until required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[HOW]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) As the driver holds dal and dc locks while waiting for CV, the outbox1
ISR is registered with noMutexWait set to true, which allows ISR to run
and signal CV. This sets a constraint on ISR to not modify variables
such as dc, dmub, etc.
4) Created dmub_outbox.c with dmub_enable_outbox_notification() to enable
outbox1 mailbox.
5) New mailbox address ranges allocated for outbox1 of size DMUB_RB_SIZE.
Created dmub functions for Outbox1: dmub_dcn20_setup_out_mailbox(),
dmub_dcn20_get_outbox1_wptr() and dmub_dcn20_set_outbox1_rptr().
6) Added functions dc_stat_get_dmub_notification() and
dmub_srv_stat_get_notification() to retrieve Outbox1 message.
7) Currently, DMUB doesn't opens DDC in AUX mode before issuing AUX
transaction. A workaround is added in dce_aux_transfer_dmub_raw() to
open in DDC in AUX mode for every AUX transaction.
8) Added dc debug option enable_dmub_aux_for_legacy_ddc enable/disable
DMUB AUX. This debug option is checked dce_aux_transfer_with_retries()
to select the method to process AUX transactions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vendor based fan noise improvement
[how]
Report timing synchronizable when DP streams time frame
difference is less than 0.05 percent. Adjust DP DTOs and
sync displays using MASTER_UPDATE_LOCK_DB_X_Y
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New proposed sequence for HUBP blanking causes regressions where the
hardware would fail to enter blank which triggers an assert in the new
sequence. This change brings back the old sequence.
Fixes: 985faf2c4e ("drm/amd/display: New sequence for HUBP blank")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Adding support for Freesync HDMI to DC and DMCU
[How]
Create DC interface and implementation on top of DMCU to support
parsing CEA blocks in DMCU.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we use the maximum possible cursor cache size when deciding if we
should attempt to enable MALL, but this prevents us from enabling the
feature for certain key use cases.
[How]
- consider cursor bpp when calculating if the cursor fits
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reverts "drm/amd/display: Revert HUBP blank behaviour for now"
- Hubp blank will fail if the pipe is locked (this is the case on
linux), so add a check to make sure pipe isn't locked, if it is then
defer the blank to post_unlock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN30 has a bug where blanking HUBP blocks pstate allow unless
HUBP_DISABLE is toggled afterwards.
[HOW]
Create a HW sequence for blanking HUBP.
1. Wait for enter VBLANK
2. Set HUBP_BLANK
3. Make sure HUBP_IN_BLANK = 1
4. Toggle HUBP_DISABLE on and off to perform soft reset
All existing calls to hubp->funcs->set_blank should be replaced with
this new sequence.
In wait_for_mpcc_disconnect, only blank the pipe being disconnected, and
leave all other pipes unmodified.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS reboots, and panel is turned off, T12 may not be maintained.
T12 is defined as the interval between VDDC off (occurs at shutdown) and
the next VDDC on (occurs when eDP is POST-ed)
[how]
DC already tracks panel power off time. Add a DC interface which DM can
call during shutdown. Ideally this should be as late as possible during
the shutdown sequence so the extra delay is minimal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
race condition of programming FP2 wrt pipe locking
and vactive state can cause underflow/black screen
[How]
Enforce the FP2 is only programmed during vactive,
and unlock pipe soon afterwards.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'dpp_input_csc_matrix' is used by some, but not all source files which
include dpp.h.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/inc/hw/dpp.h:50:42: warning: ‘dpp_input_csc_matrix’ defined but not used [-Wunused-const-variable=]
NB: Snipped lots of these for brevity
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.
[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The intended use is to force PSR into active state and ignore all
events until explicit EXIT.
A new event force_static is added to power module. It is then sent
to FW.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prior commit "Blank HUBP during pixel data blank for DCN30"
missed the call to set_disp_pattern_generator from
set_crtc_test_pattern, which re-exposed the issue for which
we initially blocked active-only p-state switching.
[How]
- remove dcn30_blank_pixel_data, set dcn30 back to dcn20 version
- new hwss funciton set_disp_pattern_generator
- dcn20 version just calls opp_set_disp_pattern_generator
- dcn30 version implements the HUBP blank
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The current end of T9 delay is relay on polling
sink status by DPCD. But the polling for sink
status change after NoVideoStream_flag set to 0.
[How]
Add function edp_add_delay_for_T9 to add T9 delay.
Move the sink status polling after blank.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If pbn_per_slot is 0, fail instead of dividing by zero and
bugchecking.
[how]
Check for zero divisor before division operation.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not
[How]
Check for updating GSL state whenever we're not doing
immediate flip
v2: Squash in build fix (Alex)
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
So we can track VSC SDP errors from display
[how]
Define the bit, and use it in driver logic
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow counter increases in AGM when performing some mode switches due
to timing sync, which is a known hardware issue.
[How]
Temporarily raise DPG height during timing sync so that underflow is not
reported.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable ODM on eDP panel with ABM will result in color difference
on the panel due to only one ABM module to set one pipe.
[How]
Block ABM in case of ODM enabled on eDP.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we transfer the WM range table to SMU, they can perform a watermark
switch right away. This can be a problem if we're in not in accelerated mode
during hw_init as SMU may initiate a dummy p-state change before the rest
of the watermarks are programmed. Watermark set A is defined to be
sufficient for all cases, so we can copy the values from set A to all other
sets, avoiding any issues from SMU doing WM switches.
[How]
- new hubbub func init_watermarks
- copy register values from set A to all other sets
- call init_watermarks before calling notify_wm_ranges
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running games or benchmarking with v-sync disabled, disabling
a plane (which is v-sync) can cause underflow. This is caused by
flips pending before pipe locking being applied after locks are
released and pipes could have been re-arranged or disconnected. This
could potentially apply a flip on incorrect pipe. Also, previous logic
of always locking pipes was unnecessary.
[How]
Only lock the pipes when there is a pipe being disabled to increase
efficiency. Before the pipes are locked, check that any pending flips
are cleared to ensure the flips are applied to the correct pipe.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, when full p-state changes are not supported, DLG parameters
are calculated for no p-state support at all. However, we are required
to always support dummy p-state changes, so we should instead calculate
DLG based on dummy p-state latency when full p-state is unsupported.
This behaviour already exists for DCN2.
[How]
- move DLG calculation inside WM calculation
- if p-state unsupported, do not recalculate for set A, instead copy from
set C, and perform DLG calculation with dummy p-state latency
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running a game/benchmark with v-sync disabled, disabling a plane
(which is v-sync) can cause an underflow. This is due to flips that are
pending before pipe locking being applied after locks are released and
pipes have been re-arranged or disconnected. This can potentially apply
a flip on the incorrect pipe.
[How]
Check that any pending flips are cleared before locking any pipes to
ensure flips are applied on the correct pipes.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Send stream active state info to DMUB
[How]
Implement GPINT to notify stream mask
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
some functions may need be dependent on stutter period in the future
how:
Extract from stutter calculations and place into perf_params structure
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If plane has changed, dcn20_detect_pipe_changes doesn't update dc_plane_state->update_flags, and the following dcn20_program_pipe can't reprogram hubp correctly.
[How]
Add a new flags bit "plane_changed" in pipe_ctx->update_flags.If old plane isn’t identical to new plane, this bit will be set and guide “dcn20_program_pipe” to programing HUBP correctly.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
