[why]
When OS reboots, and panel is turned off, T12 may not be maintained.
T12 is defined as the interval between VDDC off (occurs at shutdown) and
the next VDDC on (occurs when eDP is POST-ed)
[how]
DC already tracks panel power off time. Add a DC interface which DM can
call during shutdown. Ideally this should be as late as possible during
the shutdown sequence so the extra delay is minimal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are missing the DP info frame update on dcn30, and this will
lead to DP SDPs not being sent;
[How]
Add the DP info frame update for dcn30;
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn30_link_encoder_validate_output_with_stream was a static function.
[How]
remove the static define and include it in the header.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many VR headsets require a HSYNC width of 4, but DCN
has default minimum of 8.
[How]
Change the arbitrary minimum HSYNC width to 4 to match
DCN20.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, the offset provided to dcn30_set_disp_pattern_generator is
not forwarded to OPP for display pattern generation, resulting in
misaligned patterns and test failures.
[How]
Use the provided offset.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change in DCN10 to use IMMEDIATE_UPDATE mode for AFMT is not
reflected in DCN30 as it uses VPG.
[How]
Use IMMEDIATE_UPDATE mode for DCN30 in VPG.
Signed-off-by: Judy Cai <HuiYi.Cai@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DSCL memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
1. Write to DSCL_MEM_PWR_FORCE to put memory to shutdown when DSCL is not
used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The HDR3DLUT and SHAPER memory blocks should be powered down when
they're not in use. This will reduce power consumption.
[How]
1. Write to HDR3DLUT_MEM_PWR_FORCE to put memory to shutdown
when HDR3DLUT is not used.
2. Write to SHAPER_MEM_PWR_FORCE to put memory to shutdown
when SHAPER is not used.
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The GAMCOR memory blocks should be powered down when they're not in use.
This will reduce power consumption.
[How]
Write to GAMCOR_MEM_PWR_FORCE to put memory to shutdown
when GAMCOR is not used.
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The BLNDGAM memory blocks should be powered down when they're not in
use. This will reduce power consumption.
[How]
1. Write to BLNDGAM_MEM_PWR_FORCE to put memory to shutdown when BLNDGAM
is not used.
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, DMCU is no longer used. In these cases, some DMCU
memory should be completely powered off to save power.
[How]
1. Set DMCU_ERAM_MEM_PWR_FORCE to shutdown memory when DMCU is not in
use
2. Added a debug option to allow this behaviour to be turned off
3. Set all memory low power debug options to off first, to not
immediately cause problems
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The I2C memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Write to I2C_LIGHT_SLEEP_FORCE to put memory in light sleep when
released
2. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the FP handling to avoid nested calls.
The nested calls cause the warning below
WARNING: CPU: 3 PID: 384 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin
Fixes: 582e2ce5b4 ("drm/amdgpu/display: FP fixes for DCN3.x (v4)")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.
[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.
[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add proper FP_START/END handling and adjust Makefiles per
previous asics.
v2: fix up harder.
v3: fix clkmgr Makefile for dcn30
v4: fix old gcc handling is only required for x86
Build-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids confusion in configurations.
v2: fix build when CONFIG_DRM_AMD_DC_DCN is disabled
v3: rebase on latest code
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Commit "Blank HUBP during pixel data blank for DCN30 v2"
modifies HW behaviour during blank, which might have OS
dependencies. We need to assess the impact on amdgpu_dm
and only re-enable HUBP blanking when all necessary
changes are understood.
[How]
- revert functional changes
- leave architectural changes intact
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prior commit "Blank HUBP during pixel data blank for DCN30"
missed the call to set_disp_pattern_generator from
set_crtc_test_pattern, which re-exposed the issue for which
we initially blocked active-only p-state switching.
[How]
- remove dcn30_blank_pixel_data, set dcn30 back to dcn20 version
- new hwss funciton set_disp_pattern_generator
- dcn20 version just calls opp_set_disp_pattern_generator
- dcn30 version implements the HUBP blank
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OPTC memory blocks should be powered down when they are not in use.
This will reduce power consumption.
[How]
1. Set ODM_MEM_UNASSIGNED_PWR_MODE to shutdown memory when unassigned
2. Set ODM_MEM_VBLANK_PWR_MODE to light sleep mode when in vblank
3. Added a debug option to allow this behaviour to be turned off
4. Restructured debug options to use a bitfield in a way that's more clear
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are some timings for which we support p-state
switching in active, but not in blank. There was a
previous issue where a timing that had active-only
support would hang a p-state request when we were in
an extended blanking period. The workaround for that
issue was to block active-only p-state switching,
but that resulted in a lack of p-state support for
some common timings such as 1440p60. We want to fix
that issue properly by un-blocking p-state requests
while the display is blanked, so that we can re-enable
active-only p-state switching.
[How]
- new version of blank_pixel_data for DCN30
- call hubp->set_blank from dcn30_blank_pixel_data
- blank every hubp in the mpcc tree, and odm tree
- on blank enable, wait until the next frame before blanking HUBP
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MPC memory blocks in DCN3 should be powered down completely when
they are not in use. This will reduce power consumption.
[How]
This commits changes behaviour for dcn3 and does the following:
1. Write to MPC_RMU<X>_LOW_PWR_MODE and MPCC_OGAM_MEM_LOW_PWR_MODE to
automatically shut down memory when not in use
2. mpc3_power_on_shaper_3dlut and mpc3_power_on_ogam_lut are called
to disable force power on when configuration finishes
3. Added a debug option to allow this behaviour to be turned off
Signed-off-by: Jacky Liao <ziyu.liao@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The C standard does not specify whether an enum is signed or unsigned.
In the function prototype, one of the argument is defined as an enum
but its declaration was unit32_t. Fix this by changing the function
argument to enum in the declaration.
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Signed-off-by: Florin Iucha <florin.iucha@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need this to pass dp compliance.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required for MALL. Was accidently removed in PSR update.
Fixes: 48e48e5984 ("drm/amd/display: Disable idle optimization when PSR is enabled")
Fixes: 52f2e83e2f ("drm/amdgpu/display: add MALL support (v2)")
Acked-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not
[How]
Check for updating GSL state whenever we're not doing
immediate flip
v2: Squash in build fix (Alex)
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All DCN3x resources share ABM_MASK_SH_LIST_DCN301 definition.
The naming is misleading since it looks like DCN30 code
depends on next version DCN301, which in fact is vice-versa.
[How]
Refactor the naming to ABM_MASK_SH_LIST_DCN30.
v2: squash in build fixes (Alex)
Signed-off-by: Roman Li <roman.li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
missing OEM data to control graphics card functions
how:
load it into init_data. copied over from dcn2 implementation.
copied destruction sequence as well.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If full pstate is not supported, we should set WM set A
to 0 to prevent any hangs
[How]
If pstate is not supported, set watermark set A to 0
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.
[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable Memory Access at Last Level (MALL) feature for display.
v2: squash in 64 bit division fixes
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These function pointers are missing from dcn30_init
.calc_vupdate_position : Used to help avoid cursor stuttering
.set_pipe : Needed for setting ABM
So add them
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be programmed with timing rather than with odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.
[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.
This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable ODM on eDP panel with ABM will result in color difference
on the panel due to only one ABM module to set one pipe.
[How]
Block ABM in case of ODM enabled on eDP.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we transfer the WM range table to SMU, they can perform a watermark
switch right away. This can be a problem if we're in not in accelerated mode
during hw_init as SMU may initiate a dummy p-state change before the rest
of the watermarks are programmed. Watermark set A is defined to be
sufficient for all cases, so we can copy the values from set A to all other
sets, avoiding any issues from SMU doing WM switches.
[How]
- new hubbub func init_watermarks
- copy register values from set A to all other sets
- call init_watermarks before calling notify_wm_ranges
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During driver unload, it is expected that p-state switching is supported.
If it's not supported, PMFW will hang due to a forced p-state switch. Even
if the current timing does not support p-state normally, we still want to
force allow because the worst that can happen is underflow. This will
match Navi10 behaviour.
[How]
- new hubbub func to control the force pstate register
- force allow when releasing display ownership
- registers are inaccessible after due to m_cgs.hwNotAvailable
- explicitly disable force signal during hw_init
- if driver is disabled and re-enabled, register not cleared otherwise
Also, remove DCN3 part of dcn10_init_hw, we will not be going back to it.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add code to gracefuly handle any pipe reassignment
occuring on dcn3 hardware. This should only happen when new
surfaces are used for an update rather than old ones updated.
Fixes: 69fc1f4b97 ("amd/drm/display: avoid dcn3 on flip opp change for slave pipes")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
At the moment on flip opp reassignment does not work in all cases
for non root pipes.
This change simply makes sure we prefer pipes not used previously
when splitting in dcn3.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Eric Bernstein <eric.bernstein@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, when full p-state changes are not supported, DLG parameters
are calculated for no p-state support at all. However, we are required
to always support dummy p-state changes, so we should instead calculate
DLG based on dummy p-state latency when full p-state is unsupported.
This behaviour already exists for DCN2.
[How]
- move DLG calculation inside WM calculation
- if p-state unsupported, do not recalculate for set A, instead copy from
set C, and perform DLG calculation with dummy p-state latency
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly handle clang and older versions of gcc.
Fixes: e77165bf7b ("drm/amd/display: Add DCN3 blocks to Makefile")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.
[How]
Power off eDP backlight before power off eDP
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove duplicate header which is included twice.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values
[how]
Parse the values from VBIOS if available, and use
them if valid
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
some functions may need be dependent on stutter period in the future
how:
Extract from stutter calculations and place into perf_params structure
Signed-off-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Idle optimization and PSR conflict each other. If both enabled
at the same time, display flickering will be observed.
[How]
Disable idle optimization when PSR is enabled.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR needs to be enabled on DCN30. This is the driver part of PSR
enablement.
Also disabled retired DMCU on driver side, since DMCU is
not supported on DCN30 anymore.
[How]
Add necessary changes to enable PSR on DCN30.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This assert triggers a false negative because there are more than 4 MPCCs
on many asics.
[How]
- change assert comparisson
- remove unused variable
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpcs reg are missing for dcn3 link encoder regs list, so add them.
Also remove
DPCSTX_DEBUG_CONFIG and RDPCSTX_DEBUG_CONFIG as they are unused and
cause compile errors for dcn3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this, enabling dsc will cause a nullptr
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Programming is missing the sequence where for eDP the scrambling is
reset when testing for eye diagram test pattern.
[How]
Include the required register in the definition
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reading for DP alt registers return incorrect values due to LE_SF
definition missing.
[How]
Define correct LE_SF or DP alt registers.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Register definitions are asic-specific, so functions that use registers of
a particular asic should be static, to be exposed in asic-specific function
pointer structures.
[How]
- make register-definition-using functions static
- make some functions non-static, for future use
- remove duplicate function definition
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The only usage of dcn30_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Display goes blank after driver installation.
Aux tuning parameters must be used for 2.x only.
Wrong dc_golden_table offset was used.
[How]
Implement a new enc3_hw_init function without VBIOS constants usage to
be called for 3.x
Calculate dc_golden_table offset using sum of
base dce_info offset and golden table offset
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use DCN21 functions instead of DCE110
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling the debugfs for CRC capture we hit assertions caused by
register address and field masks and shifts missing.
[How]
We want these registers programmed, so add in the SRI/SF entries for
this register.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our validation is a known mess with actual validation mixed with
topology configuration. This change makes sure topolgical validation is
completed before any topology changes are made so we do not run into
issues where we merge and split a pipe over the course of a single call.
v2: Squash in compilation fix
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This field is missing for dcn3 so add it from dcn20.
enc2_set_dynamic_metadata() trys to sets this and we get a
generic_reg warning since the mask is not defined.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
seamless boots requires split of init_hw into hw and pipes to work. This
was implemented in dcn10_init_hw but did not apply yet to dcn30.
how:
Copy over dcn10_init_hw and adapt it to dcn30 using recent changes to
dcn3. Behavior will be different in init sequence.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to update each p-state in the bounding box
[How]
Update states when assigning values to clocks
v2: squash in patch to set min values (Alex)
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to update the bounding box to have more granular control of the
DCFCLK.
[How]
Setup DCFCLK to use STA values and also optimal values based on
UCLK.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get the values from VBIOS table
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These lines are a part of the if statement and they are supposed to
be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There're 2 .dsc_pg_control, drop the first one.
.dsc_pg_control = NULL,
.dsc_pg_control = dcn20_dsc_pg_control,
Signed-off-by: Flora Cui <flora.cui@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct gpu_info_voltage_scaling_v1_0 & gpu_info_soc_bounding_box_v1_0 is
defined in amdgpu_socbb.h
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was done already done for other DCN blocks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initilize function tables for hw programing
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Video Package generator.
used to prepare avi info, DP info etc
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Audio formating
Audio related code for setup/control
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for managing resources for DCN3
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 HUBP (Display to data fabric interface
pipe)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 MPC (Multiple pipe and plane combine)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 OPP (Output Plane Processing)
HW Blocks:
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
