If we have "ti,no-idle" specified for a module we must not disable
the the module on suspend to keep things backwards compatible.
Fixes: 386cb76681 ("bus: ti-sysc: Handle missed no-idle property in addition to no-idle-on-init")
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_DEBUG_ATOMIC_SLEEP enabled we can see the following with RTC probe:
BUG: sleeping function called from invalid context at drivers/bus/ti-sysc.c:1736
...
(sysc_quirk_rtc) from [<c060d01c>] (sysc_write_sysconfig+0x1c/0x60)
(sysc_write_sysconfig) from [<c060d9f4>] (sysc_enable_module+0x11c/0x274)
(sysc_enable_module) from [<c060f37c>] (sysc_probe+0xe9c/0x1380)
(sysc_probe) from [<c06e9384>] (platform_drv_probe+0x48/0x98)
Fixes: e8639e1c98 ("bus: ti-sysc: Handle module unlock quirk needed for some RTC")
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_DEBUG_ATOMIC_SLEEP enabled we can see the following with
wakeirqs and serial console idled:
BUG: sleeping function called from invalid context at drivers/bus/ti-sysc.c:242
...
(sysc_wait_softreset) from [<c0606894>] (sysc_enable_module+0x48/0x274)
(sysc_enable_module) from [<c0606c5c>] (sysc_runtime_resume+0x19c/0x1d8)
(sysc_runtime_resume) from [<c0606cf0>] (sysc_child_runtime_resume+0x58/0x84)
(sysc_child_runtime_resume) from [<c06eb7bc>] (__rpm_callback+0x30/0x12c)
(__rpm_callback) from [<c06eb8d8>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c06eb434>] (rpm_resume+0x638/0x7fc)
(rpm_resume) from [<c06eb658>] (__pm_runtime_resume+0x60/0x9c)
(__pm_runtime_resume) from [<c06edc08>] (handle_threaded_wake_irq+0x24/0x60)
(handle_threaded_wake_irq) from [<c01befec>] (irq_thread_fn+0x1c/0x78)
(irq_thread_fn) from [<c01bf30c>] (irq_thread+0x140/0x26c)
We have __pm_runtime_resume() call the sysc_runtime_resume() with spinlock
held and interrupts disabled.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----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=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 636338d796.
This patch is not a proper fixes the i2c2 timeouts are still
happening in some cases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get "OCP softreset timed out" warnings occasionally
at least for i2c2 on omap4 now that we check the OCP softreset completed
bit on enable.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently only setting the framedonetv_irq disabled for the SoCs
that don't have it. But we are never setting it enabled for the SoCs that
have it. Let's initialized it to true by default.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must ignore the clockactivity bit for most modules and not set it
unless specified for the module with SYSC_QUIRK_USE_CLOCKACT. Otherwise
the interface clock can be automatically gated constantly causing
unexpected performance issues.
Fixes: ae9ae12e9d ("bus: ti-sysc: Handle clockactivity for enable and disable")
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules reset automatically when idled, and when re-enabled, we must
wait for the automatic OCP softreset to complete. And if optional clocks
are configured, we need to keep the clocks on while waiting for the reset
to complete.
Let's fix the issue by moving the OCP softreset code to a separate
function sysc_wait_softreset(), and call it also from sysc_enable_module()
with the optional clocks enabled.
This is based on what we're already doing for legacy platform data booting
in _enable_sysc().
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing flush of posted write after module enable and
disable. I've seen occasional errors accessing various modules, and it
is suspected that the lack of posted writes can also cause random reboots.
The errors we can see are similar to the one below from spi for example:
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read): Data Access
in User mode during Functional access
...
mcspi_wait_for_reg_bit
omap2_mcspi_transfer_one
spi_transfer_one_message
...
We also want to also flush posted write for disable. The clkctrl clock
disable happens after module disable, and we don't want to have the
module potentially stay active while we're trying to disable the clock.
Fixes: d59b60564c ("bus: ti-sysc: Add generic enable/disable functions")
Signed-off-by: Tony Lindgren <tony@atomide.com>
As timers no longer need legacy quirk handling, let's move them to
the CONFIG_DEBUG section to make it easier to see which drivers still
need more work.
Let's also add detection for few more older timer revisions while at
it as that makes CONFIG_DEBUG output easier to read with proper names.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some early omap3 boards use timer12 for system timer, but for secure
SoCs like on n900 it's not accessible. Likely we will be configuring
unavailable devices for other SoCs too based on runtime SoC detection,
so let's use a switch to start with.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3
lcdc") dropped legacy platform data but we never added the quirks for
SWSUP_SIDLE and SWSUP_MSTANDBY for lcdc for ti-sysc driver.
This breaks suspend/resume. Let's fix the issue by enabling the same
quirks for ti-sysc driver as we had earlier with platform data.
Fixes: adb72394e2 ("ARM: OMAP2+: Drop legacy platform data for am3 lcdc")
Fixes: 23731eac98 ("bus: ti-sysc: Detect devices on am335x when DEBUG is enabled")
Reported-by: Keerthy <j-keerthy@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.
Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to probe EDMA with ti-sysc interconnect target module and with
device tree data, we need to properly detect EDMA and set the flags for
SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY for tptc.
We have these flags currently set for am4 and dra7, but not for am335x.
Let's set them for all the SoCs as the tptc module should behave the
same for all of them. It's likely that am335x was never tested to idle
EDMA tptc.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset
quirk") added support for DSS reset, but is using dispc offset also for
DSS also registers as reported by Tomi Valkeinen <tomi.valkeinen@ti.com>.
Also, we're not using dispc_offset for dispc IRQSTATUS register so let's
fix that too.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The display subsystem (DSS) needs the child outputs disabled for reset.
In order to prepare to probe DSS without legacy platform data, let's
implement sysc_pre_reset_quirk_dss() similar to what we have for the
platform data with omap_dss_reset().
Note that we cannot directly use the old omap_dss_reset() without
platform data callbacks and updating omap_dss_reset() to understand
struct device. And we will be dropping omap_dss_reset() anyways when
all the SoCs are probing with device tree, so let's not mess with the
legacy code at all.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to prepare probing display subsystem (DSS) with ti-sysc
interconnect target module driver and device tree data, let's
detect DSS related modules.
We need to also add reset quirk handling for DSS, but until that's
done, let's just enable the optional clock quirks for DSS and
omap4 HDMI. The rest is just naming of modules if CONFIG_DEBUG
is set.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RTC modules on am3 and am4 need quirk handling to unlock and lock
them for reset so let's add the quirk handling based on what we already
have for legacy platform data. In later patches we will simply drop the
RTC related platform data and the old quirk handling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.
For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.
Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can have nested ti-sysc instances that may still use the
legacy "ti,hwmods" property. Let's not warn if that's the case.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently setting -1 for non-existing sysconfig related registers
for quirks, but setting -ENODEV elsewhere. And for matching the quirks,
we're now just ignoring the non-existing registers. This will cause issues
with misdetecting DSS registers as the hardware revision numbers can have
duplicates.
To avoid this, let's standardize on using -ENODEV also for the quirks
instead of -1. That way we can always just test for a match without adding
any more complicated logic.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least display susbsystem (DSS) has modules with no sysconfig registers
and rely on custom function for module reset handling. Let's make reset
work with that too.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clk_disable_quirk and clk_enable_quirk should really be called
pre_reset_quirk and post_reset_quirk to avoid confusion like we had
with hdq1w reset.
Let's also rename the related functions so the code is easier to follow.
Note that we also have reset_done_quirk that is needed in some cases
after checking the separate register for reset done bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Because of the i2c quirk we have the reset quirks named in a confusing
way. Let's fix the 1-wire quirk accordinlyg. Then let's switch to using
better naming later on.
Fixes: 4e23be473e ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Commit d878970f6c ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes: d878970f6c ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes coccicheck warning:
drivers/bus/ti-sysc.c:506:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP IOMMU driver no longer uses the pm_runtime_irq_safe() API
after commit 1432ebbd60 ("iommu/omap: remove pm_runtime_irq_safe
flag for OMAP IOMMUs"), so the SYSC_QUIRK_LEGACY_IDLE quirk is no
longer needed for MMU devices. Drop the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For dra7 dcan and dwc3 instances we need to block clockdomain autoidle.
Let's do this with CLKDM_NOAUTO quirk flag and enable it for dcan and
dwc3.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have dts property for "ti,sysc-delay-us", and we're using it, but the
wait after OCP softreset only happens if devices are probed in legacy mode.
Let's add a delay after writing the OCP softreset when specified.
Fixes: e0db94fe87 ("bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for
musb") added quirk handling for mstandby quirk but did not consider that
we also need a quirk variant for SYSC_QUIRK_FORCE_MSTANDBY.
We need to use forced idle mode for both SYSC_QUIRK_SWSUP_MSTANDBY and
SYSC_QUIRK_FORCE_MSTANDBY, but SYSC_QUIRK_SWSUP_MSTANDBY also need to
additionally also configure no-idle mode when enabled.
Fixes: 03856e928b ("bus: ti-sysc: Handle mstandby quirk and use it for musb")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a jump target so that a call of the function “clk_put”
can be better reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must set the autogating bit on enable for AESS (Audio Engine SubSystem)
when probed with ti-sysc interconnect target module driver. Otherwise it
won't idle properly.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I noticed that when probed with ti-sysc, watchdog can trigger on am3, am4
and dra7 causing a device reset.
Turns out I made several mistakes implementing the watchdog quirk handling:
1. We must do both writes to spr register
2. We must also call the reset quirk on disable
3. On am3 and am4 we need to also set swsup quirk flag
I probably only tested this earlier with watchdog service running when the
watchdog never gets disabled.
Fixes: 4e23be473e ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current implementation for ti-sysc powers down the module once module
init is complete. However, right after power is disabled, it is enabled
via runtime PM. This is unnecessary so avoid it by re-ordering the
events a bit; move powering down of the module post runtime PM enable
which makes sure the use counts are maintained properly and there is
no extra power down/up sequence for the module.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There seems to be unnecessary extra hardreset line toggling applied
during module init. This is unnecessary, as the reset lines are already
asserted during boot, and it can cause certain modules to hang (iommus,
remoteprocs.) Remove the extra hardreset toggle, and remove the now
redundant function to handle this also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The main clocks and reset controls have a hardware level dependency,
where one can't transition state without the other one transitioning.
Because we don't have the dependency implemented in software, we must
ensure the ordering of these two is done properly; they way this is
handled is that clocks transition on software level without delay,
and the status is only polled on reset side. Because of this, we must
re-order the main clock and reset handling on the ti-sysc driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI
-----BEGIN PGP SIGNATURE-----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=s4qF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes that have trickled in through the merge window:
- Video fixes for OMAP due to panel-dpi driver removal
- Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7
- Fixing arch version on ASpeed ast2500
- Two fixes for reset handling on ARM SCMI"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: aspeed: ast2500 is ARMv6K
reset: reset-scmi: add missing handle initialisation
firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
ARM: dts: am3517-evm: Fix missing video
ARM: dts: logicpd-torpedo-baseboard: Fix missing video
ARM: omap2plus_defconfig: Fix missing video
bus: ti-sysc: Fix handling of invalid clocks
bus: ti-sysc: Fix clock handling for no-idle quirks
Commit d098913a10 ("bus: ti-sysc: Fix clock handling for no-idle
quirks") fixed handling for no-idle quirk modules that are not enabled
by the bootloader.
But it also caused unpaired clockdomain calls that won't allow idling
the system. That's because clkdm_allow_idle_nolock() and
clkdm_deny_idle_nolock() have usage count with clkdm->forcewake_count.
Let's drop the unpaired sysc_clkdm_deny_idle() to fix idling of devices.
Fixes: d098913a10 ("bus: ti-sysc: Fix clock handling for no-idle quirks")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can currently get "Unable to handle kernel paging request at
virtual address" for invalid clocks with dts node but no driver:
(__clk_get_hw) from [<c0138ebc>] (ti_sysc_find_one_clockdomain+0x18/0x34)
(ti_sysc_find_one_clockdomain) from [<c0138f0c>] (ti_sysc_clkdm_init+0x34/0xdc)
(ti_sysc_clkdm_init) from [<c0584660>] (sysc_probe+0xa50/0x10e8)
(sysc_probe) from [<c065c6ac>] (platform_drv_probe+0x58/0xa8)
Let's add IS_ERR checks to ti_sysc_clkdm_init() as And let's start treating
clk_get() with -ENOENT as a proper error. If the clock name is specified
in device tree we must succeed with clk_get() to continue. For modules with
no clock names specified in device tree we will just ignore the clocks.
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NFSroot can fail on dra7 when cpsw is probed using ti-sysc interconnect
target module driver as reported by Keerthy.
Device clocks and the interconnect target module may or may not be
enabled by the bootloader on init, but we currently assume the clocks
and module are on from the bootloader for "ti,no-idle" and
"ti,no-idle-on-init" quirks as reported by Grygorii Strashko.
Let's fix the issue by always enabling clocks init, and
never disable them for "ti,no-idle" quirk. For "ti,no-idle-on-init"
quirk, we must decrement the usage count later on to allow PM
runtime to idle the module if requested.
Fixes: 1a5cd7c23c ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reported-by: Keerthy <j-keerthy@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change return type of functions sysc_check_one_child() and
sysc_check_children() from int to void as neither ever returns an error.
Modify call sites of both functions accordingly.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bus/ti-sysc.c: In function sysc_reset:
drivers/bus/ti-sysc.c:1452:50: warning: variable quirks set but not used [-Wunused-but-set-variable]
It is never used since commit e0db94fe87 ("bus: ti-sysc: Make
OCP reset work for sysstatus and sysconfig reset bits")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some devices need to share their reset signals, like DSP MMUs, thus drop
the exclusive notation from reset request. Also, balance the init time
reset count, otherwise the resets will never be applied post boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If reset controllers are assigned to the ti-sysc target-module, only
ti-sysc is going to be able to control these. Thus, remove all the
disable_on_idle flag usage, and assert/de-assert the reset always
in the idle path. Otherwise the reset signal will always just be
de-asserted.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Parenting clockdomain for the IP should be enabled during the reset
handling logic, otherwise the reset may not finish properly. Re-order
the clockdomain control logic to avoid this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few fields in various structures is missing the corresponding
kerneldoc comments. Add them. Also, fixed the comment for sidlemodes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the appropriate SPDX license identifier in the TI sysc
interconnect target driver source files and drop the previous
boilerplate license text. Also, add the the SPDX license
identifier in the associated ti-sysc header files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clocks are not yet parsed and prepared until after a successful
sysc_get_clocks(), so there is no need to unprepare the clocks upon
any failure of any of the prior functions in sysc_probe(). The current
code path would have been a no-op because of the clock validity checks
within sysc_unprepare(), but let's just simplify the cleanup path by
returning the error directly.
While at this, also fix the cleanup path for a sysc_init_resets()
failure which is executed after the clocks are prepared.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently using a wrong register for dcan revision. Although
this is currently only used for detecting the dcan module, let's
fix it to avoid confusion.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have cases where there are no softreset bits like with am335x lcdc.
In that case ti,sysc-mask = <0> needs to be handled properly.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some devices we can get the following warning on boot:
ti-sysc 48485200.target-module: sysc_disable_module: invalid midlemode
Fix this by treating SYSC_IDLE_FORCE like we do for the other bits
for idlemodes mask.
Fixes: d59b60564c ("bus: ti-sysc: Add generic enable/disable functions")
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some older interconnect target modules need module internal clock
toggling quirks to reset properly. We've been doing this in the
platform code earlier, but need to be able to it directly in the
ti-sysc driver when we no longer rely on on the platform code.
Let's add reset handling for 1-wire, i2c and watchdog. Later on
we can add more modules like msdi and dss as they get tested.
For dra7 pcie, we should be able to just use the rstctrl reset
driver when available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we currently only detect UART on omap36xx, let's also
add support for omap34xx. And let's also fix the SWSUP mode, it should
be SWSUP_SIDLE for omap3, not SWSUP_SIDLE_ACT like for omap4 and later.
Note that we are still booting omap3 for most part without ti-sysc,
so no need to treat this change as a fix.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to deassert rstctrl resets before enabling clocks to avoid clock
"failed to enable" errors. For asserting rstctrl reset, the clocks need
to be enabled.
As the reset controller status is not available for arrays, let's use
devm_reset_control_get_optional() so we can get the status after reset.
Note that depends on a proper PRM rstctrl driver, so far I've only
tested this with earlier reset-simple patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must not assert reset for modules with no child device drivers
until in runtime_suspend. Otherwise register access will fail without
legacy mode helping us.
Let's add a flag for disable_on_idle and move the reset driver
handling to runtime suspend and resume. We can then also use the
disable_on_idle flag to reconfigure sysconfig register for PM
modes requesting it.
Let's also make the other flags use bitfield while at it instead of
bool.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have ENAWAKEUP bit that we need to configure when not
relying on platform data callbacks.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules have idlemodes wired, but not completely functional. We have
quirks for SWSUP_SIDLE and SWSUP_SIDLE_ACT to manage interconnect target
modules without hardware support, but we've been only using them so far
in legacy mode. Let's add support for SWSUP quirks in non-legacy mode too.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For interconnect target modules with autoidle bit wired, we need to manage
it for enable and disable.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to specify QUIRK_LEGACY_IDLE for device drivers that still have
pm_runtime_irq_safe() set like 8250.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had minimal OCP softreset support in ti-sysc interconnect target
module driver only used for MCAN driver so far. But it turns out that
MCAN has the sysstatus register resetdone bit inverted compared to most
other modules.
Let's make OCP softreset work for other typical cases with reset status
in sysstatus or sysconfig register so we can use the new functions for
sysc_enable_module() and sysc_disable_module() without "ti,hwmods"
property in the following patches.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to also support 16-bit writes for i2c in addition to the reads
when we start configuring the sysconfig register for reset and idle modes.
Note that only i2c revision register has LO and HI registers, so let's
add a check also for 16-bit register read. This change is currently cosmetic
and does not affect anything until we enable the module specific quirk
handling for i2c reset and enable later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to let ti-sysc driver manage clockdomain autoidle for the
duration of of reset, enable and idle. And we need to do it before we
enable the clock and after we disable it. Currently we are still
relying on platform callbacks indirectly managing clockdomain autoidle.
But I noticed that for device tree only probed drivers it now happens
only after we enabling the clocks and before we disable the clocks,
while it should be the other way around. So far I have not noticed
any issues with this though.
Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle()
functions for ti-sysc driver to use to manage clockdomains directly via
platform data callbacks. Note that we can implement the clockdomain
functions in pdata-quirks.c as for probing devices without "ti,hwmods"
custom property we don't need to use the other platform data callbacks.
Let's do this in one patch as there's is still an unlikely chance we
may need to apply this as a fix for v5.2 for dropping legacy platform
data for some devices. We also do have the option of adding back the
platform data if needed in case of trouble.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some interconnect target modules have no module control registers at
all, such as d_can on am335x and am437x.
The d_can register offset at 0 is CTL register with 0x401 as the default
value. I guess I mistook the 0x401 value for a revision register as the
value happens to look similar to what the revision registers typically
have for other modules.
To handle modules with no control registers, we need to improve the
ti-sysc driver a bit to bail out with errors on no control registers,
and then we can remove the bogus revision registers for d_can.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For non legacy cases, add generic sysc_enable_module()
and sysc_disable_module() functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation of dropping interconnect target module platform data in
favor of devicetree based data, we must pass swsup idle quirks to the
platform data functions.
For now, let's only tag the UART modules with the SWSUP_SIDLE_ACT quirk.
The other modules will get tagged with swsup quirks as we drop the
platform data and test the changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot access mcpdm registers at all unless there is an optional pdmclk
configured. As this is currently only needed for mcpdm, let's check for
mcpdm in sysc_get_clocks(). If it turns out to be needed for other modules
too, we can add more flags to the quirks table for this.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least mcpdm needs an optional external clock enabled to function and
this clock typically comes from the PMIC. We can detect mcpdm based on
the interconnect target module address and set a quirk flag early.
To do this, let's initialize the clocks a bit later and add a new
function for sysc_init_early_quirks(). Note that we cannot yet enable
the early quirks for mcpdm until the optional external clocks are
handled in the in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can do the rsstctrl a bit later, but need to deassert rstctrl reset
before the clocks are enabled if asserted. Let's only init restctrl
in sysc_init_resets() and do the reset later on just before we enable
the device clocks.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently not managing interconnect target module clocks in the
for legacy platform data based case. This causes a problem for using the
platform data based functions when dropping the platform data for the
interconnect target module configuration.
To avoid a situation where we need to populate the main and optional
clocks also for the platform data based functions, let's just manage the
clocks directly in ti-sysc driver. This means that until the interconnect
target module confugration platform data is dropped our use count for
clk_enable() will be 2 instead of 1.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The platform data based init functions typically reset the interconnect
target module configure the registers. As we may need the interconnect
target module specific quirks configured based on the revision register,
we want to move the platform data based init to happen later.
Let's allocate mdata as needed so it's available for sysc_legacy_init()
that we call with module clocks enabled from sysc_init_module().
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing we want to do is just read the module revision register to
be able to configure the module specific quirks and configure the module
registers.
As the interconnect target module may not yet be properly configured and
may need a reset first, we don't want to use pm_runtime_get() at this
point.
To read the revision register, let's just enable the all the clocks for
the interconnect target module during init even if the optional clocks
are not needed. That way we can read the revision register to configure
the quirks needed for PM runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least McPDM module depends on an external optional clock to be
usable. To make handling of the McPDM clock easier in the following
patches, let's add separate functions for handling the main clocks
and the optional clocks.
Let's also add error handling to shut down already enabled clocks
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have ti,no-idle in use in addition to ti,no-idle-on-init but we're
missing handling for it in the ti-sysc interconnect target module driver.
Let's also group the idle defines together and update the binding
documentation for it.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we return early before ddata->clocks have been allocated we will get a
NULL pointer dereference in sysc_unprepare(). Let's fix this by returning
early when no clocks are allocated.
Fixes: 0eecc636e5 ("bus: ti-sysc: Add minimal TI sysc interconnect target driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") started producing a warning for pwm-omap-dmtimer:
WARNING: CPU: 0 PID: 77 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x2f8/0x388
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4PER2 (Idle):
Data Access in Supervisor mode during Functional access
...
__pm_runtime_idle
omap_dm_timer_disable
pwm_omap_dmtimer_start
pwm_omap_dmtimer_enable
pwm_apply_state
pwm_vibrator_start
pwm_vibrator_play_work
This is because the timer that pwm-omap-dmtimer is using is now being
probed with ti-sysc interconnect target module instead of omap_device
and the ti-sysc quirk for SYSC_QUIRK_LEGACY_IDLE is not fully
compatible with what omap_device has been doing.
We could fix this by reverting the timer changes and have the timer
probe again with omap_device. Or we could add more quirk handling to
ti-sysc driver. But as these options don't work nicely as longer term
solutions, let's just make timers probe with ti-sysc without any
quirks.
To do this, all we need to do is remove quirks for timers for ti-sysc,
and drop the bogus pm_runtime_irq_safe() flag for timer-ti-dm.
We should not use pm_runtime_irq_safe() anyways for drivers as it will
take a permanent use count on the parent device blocking the parent
devices from idling and has been forcing ti-sysc driver to use a
quirk flag.
Note that we will move the timer data to DEBUG section later on in
clean-up patches.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-By: Andreas Kemnade <andreas@kemnade.info>
Tested-By: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With ti-sysc, we need to now have the device tree properties for
ti,no-reset-on-init and ti,no-idle-on-init at the module level instead
of the child device level.
Let's check for these properties at the child device level to enable
quirks, and warn about moving the properties to the module level.
Otherwise am335x-evm based boards tagging gpio1 with ti,no-reset-on-init
will have their DDR power disabled if wired up in such a tricky way.
Note that this should not be an issue for earlier kernels as we don't
rely on this until the dts files have been updated to probe with ti-sysc
interconnect target driver.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have OPT_CLKS_NEEDED in legacy platform data, but it's missing
from the ti-sysc driver for device tree based configuration.
In order to pass OPT_CLKS_NEEDED quirk flag we need to update omap4 module
data and add a new compatible for dra7 as the module layout is different
from sysc_regbits_omap4_mcasp.
Fixes: 70a65240ef ("bus: ti-sysc: Add register bits for interconnect
target modules")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can have holes in clock_roles with interface clock missing for
example. Currently getting an optional clock will fail if there are
only a functional clock and an optional clock.
Fixes: 09dfe58107 ("bus: ti-sysc: Add handling for clkctrl opt clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
As Grygorii Strashko pointed out, the runtime PM use count of the
children can be whatever at suspend and we should not use it. So
let's just suspend ti-sysc at noirq level and get rid of some code.
Let's also remove the PM_SLEEP ifdef and use __maybe_unused as the
PM code already deals with the ifdefs.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We're currently warning about busy children on suspend in
sysc_child_suspend_noirq() but the legacy code omap_device does
not do that. Let's just make it dev_dbg() instead of dev_warn().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect timer and gpio on dra7 because of the
SYSC_QUIRK_LEGACY_IDLE flag for suspend and resume.
Signed-off-by: Tony Lindgren <tony@atomide.com>
When debug is enabled, we want to see what devices we're detecting
to make things a bit easier for us. Many of these devices will also
be available on am335x and dra7, and some just need updating the
revision register mask.
Signed-off-by: Tony Lindgren <tony@atomide.com>
