Set I2C bus 14 to multi-master mode and add the panel device that will
register the I2C controller as a slave device.
In addition, in early Everest systems, the panel device was behind an
I2C switch, which doesn't work for slave mode. Get it working (albeit
unreliably, since a master transaction might switch the switch at any
moment) by defaulting the switch channel to the one with the panel.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Specifying gpio nodes under PCA led controllers no longer does anything,
so remove those nodes in the device trees.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
In keeping with previous systems, call the iio-hwmon bridge node
"iio-hwmon-battery" to distinguish it as the battery voltage
sensor.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
A series of changes to update the gpmc related bindings to yaml
format, and a few non-urgent dts fixes.
-----BEGIN PGP SIGNATURE-----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=2byI
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=mJMK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.16/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for omap gpmc bindings and devicetree files for v5.16
A series of changes to update the gpmc related bindings to yaml
format, and a few non-urgent dts fixes.
* tag 'omap-for-v5.16/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap: fix gpmc,mux-add-data type
ARM: dts: omap: Fix boolean properties gpmc,cycle2cycle-{same|diff}csen
dt-bindings: memory-controllers: ti,gpmc: Convert to yaml
dt-bindings: mtd: ti,gpmc-onenand: Convert to yaml
dt-bindings: mtd: ti,gpmc-nand: Convert to yaml
dt-bindings: memory-controllers: Introduce ti,gpmc-child
dt-bindings: net: Remove gpmc-eth.txt
dt-bindings: mtd: Remove gpmc-nor.txt
Link: https://lore.kernel.org/r/pull-1634280279-284035@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Texas Instruments Wilink 6/7/8 (wl12xx/wl18xx) Wireless LAN
Controllers can be connected via SPI or via SDIO.
Convert the two Device Tree binding documents to json-schema, and merge
them into a single document.
Add missing ti,wl1285 compatible value.
Add missing interrupt-names property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/23a2fbc46255a988e5d36f6c14abb7130480d200.1634646975.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
This adds the definition of the rtc device node. The RTC being able to
work with the oscillator at 12Mhz for now, it shares the same xtal than
the watchdog.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/all/20210823171613.18941-4-romain.perier@gmail.com
This is already in v5.15-rc5, but I'm adding it here as well to get
a clean build of the dts files.
* tag 'arm-soc/for-5.15/devicetree':
ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address
ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting
ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states
ARM: dts: bcm2711: fix MDIO #address- and #size-cells
ARM: dts: bcm283x: Fix VEC address for BCM2711
of the actually non-matching fallback-string for usb-phys
on rk3066/rk3188 (most-specific compatible is and must always
be used).
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmFv1y4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdge5FB/9goi0XtyuwiVDSV9r0Ala7Q5+iMrUj0Qtv
9Vzh28CUodSUVJqY0VTbGfzZeb1mpw/Mf6vt0JwatKcYe3wwl88+noca1JERYMST
2iZDeCMF1sx++8/7fM0Dn1+1mOF7yZR7yoi4ybFDG4LHdJE6wNCkB48LVK5jDu7t
NvkPYGtYJG3Qdfaezw/cwVel/h4EwCY5Mh4Pdn6MXKKVafKZpDo0nuI0MjCKz+Gd
7cfSpP4QtwX78gles0IhwNXhvbvxPkrOulLDBCk/AEEvOWqNXKoDc3m66yCBBzsB
3xrlDLnpNvSutFajKEcwpQCZJVrnp3dYbzhHOcC343sMLzoJm2yb
=MOmw
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=rYMJ
-----END PGP SIGNATURE-----
Merge tag 'v5.16-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Adapt gpio subnode names to match the yaml binding and removal
of the actually non-matching fallback-string for usb-phys
on rk3066/rk3188 (most-specific compatible is and must always
be used).
* tag 'v5.16-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove usb-phy fallback string from rk3066a/rk3188
ARM: dts: rockchip: change gpio nodenames
Link: https://lore.kernel.org/r/3630369.N7QejLDta5@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: Kobo Libra H2O, Tolino Vision 5, SKOV LT2 and
Colibri i.MX6ULL eMMC variants.
- A series from Fabio Estevam to correct SPI chipselect polarity for
various i.MX6/7 boards.
- A couple of patches from Krzysztof Kozlowski to clean up unsupported
properties from imx6dl-b1x5v2 and imx6dl-prtrvt boards.
- A series from Li Yang to clean up LS1021a based boards and add missing
device nodes.
- A series from Matthias Schiffer to fix typo, add SPI-NOR flash and
partition layout for imx7-tqma7/mba7 boards.
- Fix the schema check errors in i.MX PCIe device nodes.
- Other random and small fix-up and device additions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmFq0UoUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4doggAu5reFlP/kBlBoQcqVZTZdeP+bQ14
lQVrp8qj6+Z6Im2BvXF/PbeyadFY2dTzTxIc3+LbA3dne4ukiO/Ihfl1Mv1EdWUr
6pdIEIFom97jh7TDyayDnCrJFNIdIetZGAwntv/CNL465YxptK/7GVksz3WBukYl
GAug+1c5U9V8Yd+YCSYUHNVviooeXMU2OjLJzy4wq1nm231mHoI3MsoLUlNNWlA8
qjHNYor5CPBkB7Djf6CVNjTmrCK4VcCMQs7AlYF3tFi9Dq0niyTD6Jsj2INeP4qA
jvs8wTGfEAltleCQsIuLeiCstWcQCCCAlGziskyvFOmRQTOqIuKFqkrNYA==
=iChy
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=NS3u
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.16:
- New board support: Kobo Libra H2O, Tolino Vision 5, SKOV LT2 and
Colibri i.MX6ULL eMMC variants.
- A series from Fabio Estevam to correct SPI chipselect polarity for
various i.MX6/7 boards.
- A couple of patches from Krzysztof Kozlowski to clean up unsupported
properties from imx6dl-b1x5v2 and imx6dl-prtrvt boards.
- A series from Li Yang to clean up LS1021a based boards and add missing
device nodes.
- A series from Matthias Schiffer to fix typo, add SPI-NOR flash and
partition layout for imx7-tqma7/mba7 boards.
- Fix the schema check errors in i.MX PCIe device nodes.
- Other random and small fix-up and device additions.
* tag 'imx-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (42 commits)
ARM: dts: ls1021a-tsn: use generic "jedec,spi-nor" compatible for flash
ARM: dts: ls1021a: move thermal-zones node out of soc/
ARM: dts: ls1021a-tsn: remove undocumented property "position" from mma8452 node
ARM: dts: ls1021a-qds: change fpga to simple-mfd device
ARM: dts: ls1021a: add #power-domain-cells for power-controller node
ARM: dts: ls1021a: add #dma-cells to qdma node
ARM: dts: ls1021a: fix memory node for schema check
ARM: dts: ls1021a: remove regulators simple-bus
ARM: dts: ls1021a: disable ifc node by default
ARM: dts: ls1021a: breakup long values in thermal node
ARM: dts: ls1021a: fix board compatible to follow binding schema
ARM: dts: ls1021a: update pcie nodes for dt-schema check
ARM: dts: ls1021a-qds: Add node for QSPI flash
ARM: dts: ls1021a: change to use SPDX identifiers
ARM: dts: ls1021a: change dma channels order to match schema
ARM: dts: ls1021a: remove clock-names property for i2c nodes
ARM: dts: imx6dl-prtrvt: drop undocumented TRF7970A NFC properties
ARM: dts: imx6: phytec: Add gpio pinctrl for i2c bus recovery
ARM: dts: imx6: skov: provide panel support for lt2 variants
ARM: dts: imx6qdl-apalis: Fix typo in ADC comment
...
Link: https://lore.kernel.org/r/20211016140138.1603-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3066a/rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828111218.10026-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gemini PCI 'interrupt-map' does not vary by board, so let's move
the definition to a common location. This avoids having incomplete
interrupt properties (i.e. #interrupt-cells without interrupt-map).
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the PCI 'interrupt-map-mask' and '#interrupt-cells' properties
alongside the 'interrupt-map' property in each board dts. This avoids
having incomplete set of interrupt properties which may fail validation.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Highlights:
----------
- MPU:
- ST boards:
- Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
with 512 MB of DDR3. Several connections are available on this
board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in
this tag.
- Change IRQ level for STUSB1600 on DKx boards.
- Fix SAI subclocks range.
- Add ck_usb0_48m clock in USB OHCI node device to match with
STM32MP15 datasheet.
- DH boards:
- Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
- Fix SAI pin muxing.
- Odyssey:
- Set DCMI pins.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCgA7FiEEctl9+nxzUSUqdELdf5rJavIecIUFAmFplc0dHGFsZXhhbmRy
ZS50b3JndWVAZm9zcy5zdC5jb20ACgkQf5rJavIecIXnkg/+NahYkMMEa73+Fm2K
sXtu5B2Px6Vh7V5dkVgC21dQjlYyyRtNfGEGIhN9lcpVrvYU4txzUKPDAgGXhnHE
hT2gbfjY4WUer+REP//Xr5/WkLwIIN3f9b2c/b2yJf59gqjg/omSYqlnqv//356J
h/5HGxNfHvTtN+yCrfMzdP5wC+vuGh44H38E6lSLKF0yNDbbe3wlntBtWn4x+Z9x
fezKSbdKMOmlZbpdutL2LJoQUUq3nXzeVcCRgmcQOnx+ZR7L6G0pQaGgN7XyC3lX
GGRfwHWWSX7oeiVorNfXduDlsa743a3u2t0ubGmbakXtOcy8uUzsD2efhdHZrzce
X51BpbRhDSFLl9aJy1/lBmEH3y2InMXK/0zZiGlvB+6AH6xnCHCPD1obhZO9mTCK
wYvWT5r2k5VElss42C8adSd3/H/VzO/5kfDgAA2kVOSgdUOuPdgss8JdCq2vAZZi
M70zKBxGbVMIFudGONCekrp7B76658IDpyZ5CU9PkUSnGWSDH2NTmQw1vExVG65d
uEFNpyyE8P9nK0C3OIgt40Wliq+bOnu4tVDGL/XNsMYhCkJrYCLrfnIK1ydi7eZo
lv3e/EFT0RL9Rl2ttl7MLpq94QL+8bIZy9ei8O84tQGK9oL2OpmROs0VwoOOZzDN
uWQE0O4quEnWJGwOlEQSytAQrQk=
=zn1y
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=X4fu
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.16, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
with 512 MB of DDR3. Several connections are available on this
board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in
this tag.
- Change IRQ level for STUSB1600 on DKx boards.
- Fix SAI subclocks range.
- Add ck_usb0_48m clock in USB OHCI node device to match with
STM32MP15 datasheet.
- DH boards:
- Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
- Fix SAI pin muxing.
- Odyssey:
- Set DCMI pins.
* tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
ARM: dts: stm32: fix SAI sub nodes register range
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
ARM: dts: stm32: add initial support of stm32mp135f-dk board
dt-bindings: stm32: document stm32mp135f-dk board
ARM: dts: stm32: add STM32MP13 SoCs support
Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New machines:
* TYAN S7106 BMC, a x86 server from about four years ago
- Descriptions for the AST2600 ADC, which now has an upstream driver
- Lots of GPIO line names. The OpenBMC project has adopted a scheme for
naming the lines, and new additions will follow this guide
- New I2C devices for Rainier, Everest, EthanolX, Mt Jade
- Fixes for fp5280g2 which has seen some recent development, including
the addtion of a QEmu machine for testing
-----BEGIN PGP SIGNATURE-----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=i5LZ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=6eyi
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 5.15
- New machines:
* TYAN S7106 BMC, a x86 server from about four years ago
- Descriptions for the AST2600 ADC, which now has an upstream driver
- Lots of GPIO line names. The OpenBMC project has adopted a scheme for
naming the lines, and new additions will follow this guide
- New I2C devices for Rainier, Everest, EthanolX, Mt Jade
- Fixes for fp5280g2 which has seen some recent development, including
the addtion of a QEmu machine for testing
* tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: fp5280g2: Use the 64M layout
ARM: dts: aspeed: Add TYAN S7106 BMC machine
ARM: dts: aspeed: rainier: Add power-config-full-load gpio
ARM: dts: aspeed: p10bmc: Define secure boot gpio
ARM: dts: aspeed: mtjade: Add some gpios
ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
ARM: dts: everest: Define name for gpio line B6
ARM: dts: everest: Define name for gpio line Q2
ARM: dts: rainier: Define name for gpio line Q2
ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6
ARM: dts: aspeed: everest: Add I2C bus 15 muxes
ARM: dts: aspeed: rainier: Add system LEDs
ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM
ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding
Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Flag the janice SPI display lines properly for the right line
semantics.
- Fix some errors in the Skomer regulator configuration.
- Fix some SD card pin configurations on Skomer.
- Assign the Skomer SD card a 300 ms power-on delay.
- Rewrite the battery nodes to use the standard binding
"monitored-battery" as used in the updated bindings, and
provide the right Samsung battery compatibles for the Samsung
phones.
-----BEGIN PGP SIGNATURE-----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=VZoq
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFvO1oACgkQmmx57+YA
GNkS4w//fs7Pf4qZUHTEtPl3g2lIlCpo4TjHu7v7ulEBmR1TEFVkqTCbCs+RLs6k
9oQKU4+TFml/SeNg091yv8qjEA5lcfyM58Y6RQhsTrkoTFE23p9T6L1RP6qxtwg1
SC4TX8/UlsQnN7aevcbcROX1eVwPS6ePJLagPr8BrYbauF6QgUHZ9xK1InsGnfFF
wLLaFrscQHk6Fyyx+qRNl45UsRbBMjOaHwbw9IXtUc7C7A5ZehlVuavh93yzNOJE
eoaqJyXEwFp77y24z9VESiCjojgDIbURWWy1/zpwPO/C7UamGeEN+LA857m+wbvW
lg5qqTIeHfzmBXrmwQ2Cn7qkn23alGfWWA3QOyTAyW968EGU8TqkQ8N6GPsgFVgL
r60we/ddcYhOCyEsnO3ezS2pJ61TA1nvnLkxFU8wzbrSGIU4i6UALG1k3v0L2M7W
KvwbMusFKcDS71+XKGhGnUF3sBDX1v/IJWtmagWd/gpekJ4wQbnH+/DyL6WVWodn
Dd7N8QNJSoKwXRLpw3WCf7m7IZujYW/YyTb0Usbn0dI4NCtTJ1M+0vnWttVEQTrk
z9+jcJ15SOu/7OCP2jcBNtDbXsJ+8aNmQ2l/dXBr/+ZPQH3Fw+QMByshH0izSNYy
nYIrwf9LPJx5K8/ThjVJw2CCzasHBjrEr5bCO6gwA2F3mJ/+9jE=
=vIcZ
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates:
- Flag the janice SPI display lines properly for the right line
semantics.
- Fix some errors in the Skomer regulator configuration.
- Fix some SD card pin configurations on Skomer.
- Assign the Skomer SD card a 300 ms power-on delay.
- Rewrite the battery nodes to use the standard binding
"monitored-battery" as used in the updated bindings, and
provide the right Samsung battery compatibles for the Samsung
phones.
* tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Switch battery nodes to standard
ARM: dts: ux500: Skomer eMMC needs 300 ms power on
ARM: dts: ux500: Fix up SD card pin config
ARM: dts: ux500: Skomer regulator fixes
ARM: dts: ux500: Tag Janice display SPI correct
Link: https://lore.kernel.org/r/CACRpkdYf5GwRvG1Gemk4mE+aw6UnAVTY8OudwsVNPQXThHXu6g@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.16, please pull the following:
- Matthew provides a set of updates to the Northstar Plus Device Tree
files to fix a number of warnings, and prepare the files to support the
addition of the Cisco Meraki MX64/MX65 wireless controller devices and
finally adds support for those boards.
- Rafal continues to provide updates to the BCM5301X Device Tree files
in order to fix warnings with the various node names, MDIO muxes and
memory nodes. He also adds support for the external switches on the
BCM53573 SoC and adds Tenda AC9 switch ports.
- Christian provides the description of the Ethernet switch ports for
the Cisco Meraki MR32 based on the 53016 SoC
- Arinc adds support for the Asus RT-AC88U device based on the BCM4709
and featuring 8 Ethernet ports over the integrated and the external
Realtek switch (not supported yet)
- Stefan adds support for the Raspberry Pi Compute Module 4 IO board and
does a number of preparatory changes to get there to the Device Tree
files before doing the actual addition
-----BEGIN PGP SIGNATURE-----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=KGAI
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmFvOiUACgkQmmx57+YA
GNmQ/Q/+J2HunngXPMz68OysNCQ8tvT2eWRQo5Ju5KGiabXrF7QNeNPysxAwhvZv
Wv0Bfg0aONEjfJgonub0ezKDd/GrsBxOaHdA/5VNcCGZyPvXfRRkvCkFggI3oQsO
wWWX523kcsLyck59kixLOxJdHjplcwV/Hj6qW0+iGNCglVRDL73DoVzF5nqtUgMP
WXcQl9L5YTjnCmRJwsQylqIZJzGIEhNwr5wYp/RtEVe9vdJ2uQ74PqLcZJZCPD1g
WpMNgAS0w5ZocIbyRlvN5SmLI8gM7nwwmzp9Eq2q6bzpPKfBBcrSySPNEj3avTCc
Fpb1GwlRECTlVc90eF1Om6garFkdO6xorxaagqQAebxSOZ5uWH5urzfUVSuKVBDv
uTWUNXFghukjHVdnv1rblxfRlIzj5cFats/0lQTzjo/ankQMBs53vZ3720TV2uq7
D5go3cd4V6ebVP0NoINYs+4iO2BaXA32g7SwGier8X6p2xPVKuZ8+18+wytE1RoY
hobWTwdY5DbsfV1+z1cksNHrgY1NRXVlKEw6gkw5RXMf2GZ7XSO1CpzNEHsp7J4y
S51bmO7LZqx8wSq+WCQjL0RzQbzSmls28ofyiEAlsGG0wzYdRWeLbdqU7UijgFRc
r8B0ydAiKS/NH1r3hh+ht+j6TG2vCxm8G1KWYjZXOM3oJyGnbpQ=
=Ptpv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.16, please pull the following:
- Matthew provides a set of updates to the Northstar Plus Device Tree
files to fix a number of warnings, and prepare the files to support the
addition of the Cisco Meraki MX64/MX65 wireless controller devices and
finally adds support for those boards.
- Rafal continues to provide updates to the BCM5301X Device Tree files
in order to fix warnings with the various node names, MDIO muxes and
memory nodes. He also adds support for the external switches on the
BCM53573 SoC and adds Tenda AC9 switch ports.
- Christian provides the description of the Ethernet switch ports for
the Cisco Meraki MR32 based on the 53016 SoC
- Arinc adds support for the Asus RT-AC88U device based on the BCM4709
and featuring 8 Ethernet ports over the integrated and the external
Realtek switch (not supported yet)
- Stefan adds support for the Raspberry Pi Compute Module 4 IO board and
does a number of preparatory changes to get there to the Device Tree
files before doing the actual addition
* tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux: (31 commits)
arm64: dts: broadcom: Add reference to RPi CM4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4
dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4
ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi
dt-bindings: display: bcm2835: add optional property power-domains
ARM: dts: BCM5301X: Add DT for Asus RT-AC88U
ARM: BCM53016: MR32: get mac-address from nvmem
ARM: BCM53016: Specify switch ports for Meraki MR32
ARM: dts: BCM53573: Add Tenda AC9 switch ports
ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
ARM: dts: BCM5301X: Specify switch ports for more devices
ARM: dts: NSP: Fix MX65 MDIO mux warnings
ARM: dts: NSP: Fix MX64/MX65 eeprom node name
ARM: dts: NSP: Fix MDIO mux node names
ARM: dts: NSP: Fix mpcore, mmc node names
ARM: dts: NSP: Add bcm958623hr board name to dts
ARM: dts: BCM5301X: Fix memory nodes names
ARM: dts: BCM5301X: Fix MDIO mux binding
ARM: dts: BCM5301X: Fix nodes names
...
Link: https://lore.kernel.org/r/20211013174016.831348-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This extends the previous limited description of MSM8226 with SDHC,
UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this,
initial support for the LG G Watch R smartwatch is introduced.
APQ8064 gets a couple of DT updates, one which will allow the GPU driver
to drop supporting legacy "opp tables" in the future.
DT bindings and DTS files are updated with additional compatibles, for
completeness.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAmFlyMwbHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3F6v0P/17moA0ag9bouNejiVbz
qEYqDobqi6YvdEv8bDMcbHZKe7WpWy3eW304pp8gKj/u7E05rNdNAi45bZZ697Zt
BhisknGupCw0+WjKVViAG7jSi7wVuBHyxJ5Y9e/iwItpmLaApQkW7/1lMIegOlsY
BboFsHgRnflFO6fBg5LRhRPwFxZG0x1GRjtTYH4LiG8bOUa6TJy+/V+Wj8UTOspL
ntmfFd295S4tm92XEYWhvIqKCrYLrn4/HQ5P9nB0kRFpPS7VX5C96a3t+vY9wSin
IZwX+p4BsdnIG2ZucGKbEH+9PnWqrH1hmFJVLu99s/PulOd2GGEtWZeW3JongLp6
R42JTx+nmFD4yCzL34qSVUEschcNaprSwqZLesJcFcXR1ZJ86Eo5S/8DMbmpscXT
uIDkhTNTsoOVSpjZ5ZKfok2J9lpKl+FmpST25FuNapUmuAkgvJapipRk6DkXyT0r
jAmTrSBRFAFcWY9isikKPPp97MuXguX+rHv+8Ki+K1ePfU+/8CftFIwlg8z6TfvY
tUugn5K3xXrRBgR/WWH+6VJF9mq/XTCeaAlvmJzDlnTE/z2qGCrgQLKeH9vWTwT3
uBG9dP+YhDvhXXWLU00W8xhSN/yb+riU2jj3FElhREmHL5B0/cKM2Hf1X5ugGImV
2XKdAwuXcqJT9NpGgxuyL/KD
=x0TI
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=ur86
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm DTS updates for v5.16
This extends the previous limited description of MSM8226 with SDHC,
UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this,
initial support for the LG G Watch R smartwatch is introduced.
APQ8064 gets a couple of DT updates, one which will allow the GPU driver
to drop supporting legacy "opp tables" in the future.
DT bindings and DTS files are updated with additional compatibles, for
completeness.
* tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
dt-bindings: arm: qcom, add missing devices
ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY
ARM: dts: qcom: fill secondary compatible for multiple boards
ARM: dts: qcom: apq8064: adjust memory node according to specs
ARM: dts: qcom: apq8064: Convert adreno from legacy gpu-pwrlevels to opp-v2
ARM: dts: qcom: Add support for LG G Watch R
dt-bindings: arm: qcom: Document APQ8026 SoC binding
ARM: dts: qcom: Add pm8226 PMIC
ARM: dts: qcom: msm8226: Add more SoC bits
dt-bindings: arm: qcom: Document SDX65 platform and boards
Link: https://lore.kernel.org/r/20211012174310.1017857-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A new 'chassis-type' root node property has recently been approved for
the device-tree specification.
Add this property for end-user devices (such as laptops,
smartphones and tablets) based on Samsung S5Pv210 ARM SoCs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211017101228.19478-3-krzysztof.kozlowski@canonical.com
A new 'chassis-type' root node property has recently been approved for
the device-tree specification.
Add this property for end-user devices (such as laptops,
smartphones and tablets) based on Samsung Exynos ARM SoCs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211017101228.19478-2-krzysztof.kozlowski@canonical.com
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-24-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-23-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-22-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-21-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-20-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-19-dmitry.baryshkov@linaro.org
The majority of device tree nodes for mpps use xxxx-state as pinctrl
nodes. Change names of mpps pinctrl nodes for qcom-apq8060-dragonboard
board to follow that pattern.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-10-dmitry.baryshkov@linaro.org
Rename mpp node to mpps@50 (instead of mpp@50). Also add gpio-ranges
property to mpps device tree nodes, adding the mapping between pinctrl
and GPIO pins.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-9-dmitry.baryshkov@linaro.org
Currently all gpio nodenames are sort of identical to there label.
Nodenames should be of a generic type, so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20211007144019.7461-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A small number fixes this time, mostly touching actual code:
- Add platform device for i.MX System Reset Controller (SRC) to fix
a regression caused by fw_devlink change.
- A fixup for a boot regression caused by my own rework for the
Qualcomm SCM driver.
- Multiple bugfixes for the Arm FFA and optee firmware drivers,
addressing problems when they are built as a loadable module.
- Four dts bugfixes for the Broadcom SoC used in Raspberry pi, addressing
VEC (video encoder), MDIO bus controller #address-cells/#size-cells,
SDIO voltage and PCIe host bridge dtc warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=87lq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A small number fixes this time, mostly touching actual code:
- Add platform device for i.MX System Reset Controller (SRC) to
fix a regression caused by fw_devlink change
- A fixup for a boot regression caused by my own rework for the
Qualcomm SCM driver
- Multiple bugfixes for the Arm FFA and optee firmware drivers,
addressing problems when they are built as a loadable module
- Four dts bugfixes for the Broadcom SoC used in Raspberry pi,
addressing VEC (video encoder), MDIO bus controller
#address-cells/#size-cells, SDIO voltage and PCIe host bridge
dtc warnings"
* tag 'arm-soc-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: imx: register reset controller from a platform driver
iommu/arm: fix ARM_SMMU_QCOM compilation
ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address
ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting
tee: optee: Fix missing devices unregister during optee_remove
ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states
ARM: dts: bcm2711: fix MDIO #address- and #size-cells
ARM: dts: bcm283x: Fix VEC address for BCM2711
firmware: arm_ffa: Fix __ffa_devices_unregister
firmware: arm_ffa: Add missing remove callback to ffa_bus_type
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get
lost currently, so fix the IRQ type.
Fixes: 83686162c0 ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The
DCMI pins used on this output are defined in the pin state definition
&pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit
02814a4152). Set these pins as the default
pinctrl of the DCMI peripheral in the board device tree.
The pins are not used for any other purpose, so it seems safe to assume
most users will not need to override (delete) what this patch provides.
status defaults to "disabled", so the peripheral will not be
unnecessarily started. And the users who actually intend to make use of
a camera on the DVP port will have this little part of the configuration
ready.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
We cannot list all the possible chips used in different board revisions,
just use the generic "jedec,spi-nor" compatible instead. This also
fixes dtbs_check error:
['jedec,spi-nor', 's25fl256s1', 's25fl512s'] is too long
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes dtbs-check error from simple-bus schema:
soc: thermal-zones: {'type': 'object'} is not allowed for {'cpu-thermal': ..... }
From schema: /home/leo/.local/lib/python3.8/site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property "postion" is not documented in the mma8452 binding. Remove it
to resolve the error in "make dtbs_check"
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FPGA is not really a bus but more like an MFD device. Change the
compatible string from "simple-bus" to "simple-mfd". This also fix a
node name issue with simple-bus schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the #power-domain-cells for power-controller node as required by the
schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following error from "make dtbs_check"
memory: False schema does not allow ...
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no regulator bus in hardware. So move the regulator nodes out
and remove the regulators simple-bus. This also make the dts align with
the simple-bus schema.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the bus in the SoC dtsi file to be enabled only in board dts
files. Also breakup long values in the ifc node to fix dtbs_check.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Align the compatible strings with the board binding defined in schema
file.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing node for qspi flash.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although the ordering of DMA channels was not relevant in the txt binding,
it is defined as ordered in the converted yaml schema. Update the dts
to match the order.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The property is optional and not used in matching the clock in driver.
Remove it to avoid dtbs_check issues.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make use of the i2c bus recovery feature and enable it on PHYTEC
phyCORE-based modules and boards.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This force-converts the per-device battery node into the standard
properties using "simple-battery" for the HREF machines and the
corresponding Samsung battery for the mobile phones.
This is fine to do since the battery data in the DTS files has never
been deployed or used. In commit a1149ae975
"ARM: ux500: Disable Power Supply and Battery Management by default"
it was turned off and has not been switched back on since. In
the meantime standardized bindings for batteries have appeared
making the old AB8500 battery bindings obsolete.
The battery node which is now in the middle of an included file
is obviously a per-device piece of information so push this down
to each board. The HREF machines all have the same battery and can
share a single node in the HREF dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
5.15, please pull the following:
- Stefan fixes the VEC (video encoder) bus address for 2711, fixes the
MDIO bus controller #address-cells/#size-cells inversion and the SDIO
regulator voltage ranges
- Nicolas fixes DTC warnings for the PCIe host bridge and its child
USB device
-----BEGIN PGP SIGNATURE-----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=EOTX
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=SPDH
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.15/devicetree' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.15, please pull the following:
- Stefan fixes the VEC (video encoder) bus address for 2711, fixes the
MDIO bus controller #address-cells/#size-cells inversion and the SDIO
regulator voltage ranges
- Nicolas fixes DTC warnings for the PCIe host bridge and its child
USB device
* tag 'arm-soc/for-5.15/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711-rpi-4-b: Fix usb's unit address
ARM: dts: bcm2711-rpi-4-b: Fix pcie0's unit address formatting
ARM: dts: bcm2711-rpi-4-b: fix sd_io_1v8_reg regulator states
ARM: dts: bcm2711: fix MDIO #address- and #size-cells
ARM: dts: bcm283x: Fix VEC address for BCM2711
Link: https://lore.kernel.org/r/20211012213841.1872021-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the device tree for a Netgear GS110EMX switch featuring 8 Gigabit
ports and 2 Multi-Gig ports (100M/1G/2.5G/5G/10G). An 88E6390X switch
sits at its core connecting to two 88X3310P 10G PHYs. The control plane
is handled by an 88F6811 Armada 381 SoC.
The following functionality is tested:
- 8 gigabit Ethernet ports connecting via 88E6390X to the 88F6811
- serial console UART
- 128 MB commercial grade DDR3L SDRAM
- 16 MB serial SPI NOR flash
The two 88X3310P 10G PHYs while detected during boot seem neither to
detect any link nor pass any traffic.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
dtbs_check currently complains that:
arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning
(pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format
error, expected "0,0"
Unsurprisingly pci@0,0 is the right address, as illustrated by its reg
property:
&pcie0 {
pci@0,0 {
/*
* As defined in the IEEE Std 1275-1994 document,
* reg is a five-cell address encoded as (phys.hi
* phys.mid phys.lo size.hi size.lo). phys.hi
* should contain the device's BDF as 0b00000000
* bbbbbbbb dddddfff 00000000. The other cells
* should be zero.
*/
reg = <0 0 0 0 0>;
};
};
The device is clearly 0. So fix it.
Also add a missing 'device_type = "pci"'.
Fixes: 258f92d2f8 ("ARM: dts: bcm2711: Add reset controller to xHCI node")
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The TYAN S7106 is a server platform with an ASPEED AST2500 BMC.
Signed-off-by: Oskar Senft <osk@google.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210909004920.1634322-1-osk@google.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the power-config-full-load described in:
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md#power-config-full-load
The power-config-full-load gpio is designed to be used to specify how
many power supplies the system should have, in rainier it is 2 or 4. If
enough power supplies fail so that the system no longer has redundancy
(no longer n+1), the hardware will signal to the Onboard Chip Controller
that the system may be oversubscribed, and performance may need to be
reduced so the system can maintain it's powered on state.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211005192226.213539-1-anoo@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This contains various cleanup patches to 32-bit ARM Tegra device trees
and enables USB OTG mode on the Nexus 7.
-----BEGIN PGP SIGNATURE-----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=kkWf
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=X0fi
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.16-rc1
This contains various cleanup patches to 32-bit ARM Tegra device trees
and enables USB OTG mode on the Nexus 7.
* tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Remove useless usb-ehci compatible string
ARM: tegra: Remove unused backlight-boot-off property
ARM: tegra: nexus7: Enable USB OTG mode
ARM: tegra: Add new properties to USB PHY device-tree nodes
ARM: tegra: Update Broadcom Bluetooth device-tree nodes
ARM: tegra: acer-a500: Correct compatible of ak8975 magnetometer
Link: https://lore.kernel.org/r/20211008201132.1678814-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Addition of a new variant in the sama5d2 family: the sama5d29 with
significant updates being CAN and Ethernet controllers;
- Add support for Exegin Q5xR5 and CalAmp LMU5000 boards which were
maintained up to this moment, separately, in OpenWrt tree;
- Two more boards gained I2C bus recovery support;
- Tse850 updated with one Ethernet fix;
- Sama7g5ek gained ADC nodes and sama5d27_wlsom1 WiFi support.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYWQuQwAKCRAfOrpwrNPN
DP3CAQCOSNWmCOwvlWJdu7/FjsxPsPXmUyUHW0oAFF80sEkaBQEAiN6QlIDvTB9U
Cxn/wYe2zbQ+vJbqkuODTqK104OUdA4=
=Ph50
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=FHko
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT #1 for 5.16:
- Addition of a new variant in the sama5d2 family: the sama5d29 with
significant updates being CAN and Ethernet controllers;
- Add support for Exegin Q5xR5 and CalAmp LMU5000 boards which were
maintained up to this moment, separately, in OpenWrt tree;
- Two more boards gained I2C bus recovery support;
- Tse850 updated with one Ethernet fix;
- Sama7g5ek gained ADC nodes and sama5d27_wlsom1 WiFi support.
* tag 'at91-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: dts: sama5d29: Add dtsi file for sama5d29
ARM: dts: at91-sama5d2_icp.dts: Added I2C bus recovery support
ARM: dts: at91: tse850: the emac<->phy interface is rmii
ARM: dts: at91: add Exegin Q5xR5 board
dt-bindings: ARM: at91: document exegin q5xr5 board
dt-bindings: add vendor prefix for exegin
ARM: dts: at91: add CalAmp LMU5000 board
dt-bindings: ARM: at91: document CalAmp LMU5000 board
dt-bindings: add vendor prefix for calamp
ARM: dts: at91: at91sam9260: add pinctrl label
ARM: dts: at91-sama5d27_som1_ek: Added I2C bus recovery support
ARM: dts: at91: sama7g5ek: enable ADC on the board
ARM: dts: at91: sama7g5: add node for the ADC
ARM: dts: at91: sama5d27_wlsom1: add wifi device
Link: https://lore.kernel.org/r/20211011123438.16562-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpmc,mux-add-data is not boolean.
Fixes the below errors flagged by dtbs_check.
"ethernet@4,0:gpmc,mux-add-data: True is not of type 'array'"
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc,cycle2cycle-{same|diff}csen are boolean properties. Fix them
to prevent dtbs_check errors.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input pin that indicates that the BMC is configured to boot with security
protections enforced.
Pulled up by default (secure). Placing the jumper will pull the pin down
(bypass security).
When in the secure boot state, it makes the EEPROM at 0x50 on bus 14
read only.
Link: https://lore.kernel.org/r/20210923074606.283393-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add S0_SCP_AUTH_FAIL, S1_SCP_AUTH_FAIL gpios to indicates firmware
authentication fail on each socket.
Add gpio RTC_BAT_SEN_EN to enable RTC battery adc sensor.
Add BMC_I2C4_O_EN gpio to go high at boot to enable access to I2C4 bus.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Thang Nguyen <thang@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20210917082945.19111-1-quan@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:
- Fix compiler warning for sysc_init_soc() that got recently introduced
- Fix external abort for am335x pruss as otherwise some am335x will hang
- Use CLKDM_NOAUTO quirk also for dra7 dcan1
- Fix older NAND device node regression for omap3-sdp
-----BEGIN PGP SIGNATURE-----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=2z/N
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=fI0x
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.15
Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:
- Fix compiler warning for sysc_init_soc() that got recently introduced
- Fix external abort for am335x pruss as otherwise some am335x will hang
- Use CLKDM_NOAUTO quirk also for dra7 dcan1
- Fix older NAND device node regression for omap3-sdp
* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
soc: ti: omap-prm: Fix external abort for am335x pruss
bus: ti-sysc: Add break in switch statement in sysc_init_soc()
Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no such thing as a generic USB EHCI controller. The EHCI
controllers found on Tegra SoCs are instantiations that need Tegra-
specific glue to work properly, so drop the generic compatible string
and keep only the Tegra-specific ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver
starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmFdm+0UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7LyAf/QS/9SEi7xwgmsE6ywozsk/VZB8Ze
77MSlR1U/HoqtreF9RNGB31Wv2TI0Cxi05TEbSonFDrk4rHFdh158YQZk8sINWOT
AXIWso6qMqCA8onmHkTLgYKj2rFBdfzKffhdv/IhmIPW08DouFxRq1sHFOae0Dv4
Lo+4fhHqd3OYGPAi3Po9DgYOjJt7VujY7XRJJIrq3RMarxbXDAbpz7W12ioB/j1T
x24jxEnaDfgpfNiCRoks2CEttnA28iIY3BXMH6J37ilFrKWTdyT45oIFe4bs8u7n
ZRuwJs8W5FclRYVquXkDlh/i/h1YmxdDs80lseQl9G/dsZZ3oKxE+VpNrA==
=Xtlw
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=lVwf
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.15, round 2:
- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver
starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.
* tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
arm64: dts: imx8: change the spi-nor tx
ARM: dts: imx: change the spi-nor tx
Link: https://lore.kernel.org/r/20211006125734.GA10197@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the matching carrier for Raspberry Pi Compute Module 4.
Instead of xHCI USB host controller there is just a USB 2.0 interface
connected to the DWC2 controller from the BCM2711. As a result
there is a free PCIe Gen 2 socket. Also there are 2 full-size HDMI 2.0
connectors.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-10-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The Raspberry Pi Compute Module 4 (CM4) are SoMs which contain the
following:
* BCM2711 quad core processor
* up to 8 GB RAM
* up to 32 GB eMMC
* a GPIO expander
* Gigabit PHY BCM54210PE
* Wifi/BT module with internal and external antenna
The eMMC and the Wifi/BT module are optional.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-9-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
A Wifi/BT chip is quite common for the Raspberry Pi boards. So move those
definitions into a separate dtsi in order to avoid copy & paste. This
change was inspired by a vendor tree patch from Phil Elwell.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-7-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
DT schema check complains at sd_io_1v8_reg about the following:
[1800000, 1, 3300000, 0] is too long
Additional items are not allowed (3300000, 0 were unexpected)
So fix the states definition.
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-3-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The values of #address-cells and #size-cells are swapped. Fix this
and avoid the following DT schema warnings for mdio@e14:
#address-cells:0:0: 1 was expected
#size-cells:0:0: 0 was expected
Fixes: be8af7a9e3 ("ARM: dts: bcm2711-rpi-4: Enable GENET support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The VEC has a different address (0x7ec13000) on the BCM2711 (used in
e.g. Raspberry Pi 4) compared to BCM283x (e.g. Pi 3 and earlier). This
was erroneously not taken account for.
Definition of the VEC in the devicetrees had to be moved from
bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this
differentiation.
Fixes: 7894bdc622 ("ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1626980528-3835-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
BB2D is a Vivante GC 2D Accelerator.
This adds the node to the dts file within a target module node.
Crossbar index number is used for interrupt mapping.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee32711195 ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace depreciated nodenames, fix label name to match scheme.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hyphens should be used in label names. make dtbs_check complains
about that since it does not match the corresponding pattern
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch the compatible for the am33xx_pinmux pin controller node from
pinctrl-single to pinconf-single. The only change between these two
compatibles is that PCS_HAS_PINCONF will be true. This then allows
pinconf properties to be utilized.
The purpose of this change is to allow the PocketBeagle to use:
pinctrl-single,bias-pullup
pinctrl-single,bias-pulldown
This dts already defines these properites for gpio pins in the default
pinctrl state but it has no effect unless PCS_HAS_PINCONF is set.
The bias properties can then be modified on the corresponding gpio lines
through the gpiod uapi. The mapping between the pins and gpio lines is
defined by gpio-ranges under the gpio controller nodes in am33xx-l4.dtsi
Signed-off-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nand is on CS1 so reg properties first field should be 1 not 0.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- I2C EEPROM support on the RZA2MEVB development board,
- DMA, USB2.0, and audio support for the RZ/G2L SoC,
- USB2.0, I2C, audio, ADC, and CANFD support for the RZ/G2L SMARC EVK
development board,
- Support for more R-Car Gen3e SoCs (H3e, M3e, M3Ne(-2G), D3e, E3e,
H3Ne),
- PWM support for the R-Car M3-W+ and V3U SoCs,
- IPMMU support for SDHI on the R-Car V3U SoC,
- Switches support for the Falcon development board,
- Improve Ethernet PHY descriptions to fix reset handling after kexec,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYVbUMwAKCRCKwlD9ZEnx
cC3lAQCXJwi2QXqvWKKLPmnkT7GwD5OaF4F1ykBmfExD3fHpcwD5ATmkHwvIGkRG
JOH1BDNSmcq36xwaAsRXmCAWm0dG6wE=
=HxRU
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=9/VI
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.16
- I2C EEPROM support on the RZA2MEVB development board,
- DMA, USB2.0, and audio support for the RZ/G2L SoC,
- USB2.0, I2C, audio, ADC, and CANFD support for the RZ/G2L SMARC EVK
development board,
- Support for more R-Car Gen3e SoCs (H3e, M3e, M3Ne(-2G), D3e, E3e,
H3Ne),
- PWM support for the R-Car M3-W+ and V3U SoCs,
- IPMMU support for SDHI on the R-Car V3U SoC,
- Switches support for the Falcon development board,
- Improve Ethernet PHY descriptions to fix reset handling after kexec,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (45 commits)
arm64: dts: renesas: rcar-gen3: Add missing Ethernet PHY resets
ARM: dts: rzg1: Add missing Ethernet PHY resets
ARM: dts: r-mobile: Add missing Ethernet PHY resets
arm64: dts: renesas: Add compatible properties to RTL8211E Ethernet PHYs
arm64: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
arm64: dts: renesas: Add compatible properties to AR8031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to uPD6061x Ethernet PHYs
ARM: dts: renesas: Add compatible properties to RTL8201FL Ethernet PHYs
ARM: dts: renesas: Add compatible properties to LAN8710A Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8081 Ethernet PHYs
ARM: dts: renesas: Add compatible properties to KSZ8041 Ethernet PHYs
arm64: dts: renesas: beacon: Fix Ethernet PHY mode
ARM: dts: renesas: Fix SMSC Ethernet compatible values
arm64: dts: renesas: rzg2l-smarc: Enable CANFD
arm64: dts: renesas: rzg2l-smarc-som: Enable ADC on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Move extal and memory nodes to SOM DTSI
arm64: dts: renesas: r8a779a0: falcon-cpu: Add SW47-SW49 support
arm64: dts: renesas: rzg2l-smarc: Add Mic routing
arm64: dts: renesas: rzg2l-smarc: Enable audio
...
Link: https://lore.kernel.org/r/cover.1633081147.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Revert cc8870bf4c to fix the regression on i.MX6 that suspend
support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to
f611b1e762 ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmFMHfQUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7QUwf/dO+FrGSWlVxHeG/oKMb6iQqZs0zb
40F68OYCF+ucGJlwAkErnLcqxtC7rD8NHsGvxnXMbTNlhtjl5USw0tIki+3cw1EP
LggbTjlOCRDLnF2YmWfXN+hLz5On38TG9TvvWt8x2CBO9WXgipaG8JHCCsxdXZus
vk37hZSAlwqmkXHHDApBMsMTqma8ZlDRELrgnXeHL53pYFDxKWoOhL0WHvvZ+kFO
I3lnIB4FdAOgm+EoAAW2s6v/IJobhC19KoKBrtf3FRo6KQk5A6L8T2CFPMkL0cFf
zJboFIOmwMnw00O44RWKDPWDQKKMZYJubj+zHaAnUFRfg4D9KKSDQApffA==
=oDbx
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=giT+
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.15:
- Revert cc8870bf4c to fix the regression on i.MX6 that suspend
support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to
f611b1e762 ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.
* tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable fb
ARM: dts: imx6qdl-pico: Fix Ethernet support
ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo
ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo
Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine"
ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe
Link: https://lore.kernel.org/r/20210923063356.GK13480@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bunch of DTS fixes to resolve addressing issues with some of the device
nodes, dropping unused/undocumented properties in various nodes, and
aligning node names with dtschema.
-----BEGIN PGP SIGNATURE-----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=t92O
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=YUKB
-----END PGP SIGNATURE-----
Merge tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Juno/Vexpress fixes for v5.15
Bunch of DTS fixes to resolve addressing issues with some of the device
nodes, dropping unused/undocumented properties in various nodes, and
aligning node names with dtschema.
* tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Fix motherboard bus 'interrupt-map'
arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes
arm: dts: vexpress-v2p-ca9: Fix the SMB unit-address
arm: dts: vexpress: Drop unused properties from motherboard node
arm64: dts: arm: drop unused interrupt-names in MHU
ARM: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: fvp: Remove panel timings
Link: https://lore.kernel.org/r/20210927105249.3583380-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This corrects the use of depricated chipid and clock names, for which
support was finally dropped from the driver. It also ensures that the
DSI PLL is fed by the correct clock, now that it's being migrated to not
rely on global clock names.
-----BEGIN PGP SIGNATURE-----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=xHHw
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=C1Zc
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm DTS fixes for v5.15
This corrects the use of depricated chipid and clock names, for which
support was finally dropped from the driver. It also ensures that the
DSI PLL is fed by the correct clock, now that it's being migrated to not
rely on global clock names.
* tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: apq8064: update Adreno clock names
ARM: dts: qcom: apq8064: Use 27MHz PXO clock as DSI PLL reference
ARM: dts: qcom: apq8064: use compatible which contains chipid
Link: https://lore.kernel.org/r/20210930025526.1146-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a label for the touchscreen to allow a custom baseboard to
disable this node if needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The STMPE811 ADC on the Apalis SoM board can be used as a provider
of ADC capabilities to other devices, for example, when a custom
baseboard has an SN74LV4051 analog mux.
Pass the 'io-channel-cells' parameter to indicate such possibility.
While at it, also pass a label for the adc device, so that it can
be referenced in the custom baseboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended not to use underscore in node names.
Change it to dash.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make operating point definitions comply with binding
specifications.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make operating point definitions comply with binding
specifications.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only led-X or led are allowed according to bindings definition.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Tolino Vision 5 Ebook reader. It is
based on boards called ¨e70k02¨. It is equipped with an imx6sl SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Kobo Libra H2O Ebook reader. It is based on
boards called e70k02. It is equipped with an imx6sll SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Netronix board E70K02 can be found some several Ebook-Readers,
at least the Kobo Libra H2O and the Tolino Vision 5. The board
is equipped with different SoCs requiring different pinmuxes.
For now the following peripherals are included:
- LED
- Power Key
- Cover (gpio via hall sensor)
- RC5T619 PMIC
- Backlight via lm3630a
- Wifi sdio chip detection (mmc-powerseq and stuff)
It is based on vendor kernel but heavily reworked due to many
changed bindings.
Known limitations: cold colored backlight does not work due to
incompatible hard coded overvoltage setting in the driver.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the partition layout also used by the bootloader.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SPI-NOR flash on the SoM was missing from the device tree.
The TQMa7 as a designated QSPI_RESET# pin, however depending on the
hardware configuration the pin may be unconnected, or be used for a
different purpose. With this in mind, we mux the pin as a pullup and
define an input hog for it, but keep it a separate pin group, so that it
is easy for dependent Device Trees to modify the configuration.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"TQ-Systems" is written with a dash.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MPL3115A2 I2C pressure sensor driver does not take a VCC regulator.
The bindings are so far trivial, but the datasheet does not have a VCC
pin.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device tree for a Colibri iMX6ULL 1GB which has a eMMC instead of
the raw NAND used on other SKUs.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nexus 7 has OTG-cable microUSB port, enable OTG mode. USB peripheral
devices now can be connected to Nexus 7 using OTG adapter, switching
USB port into host mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to USB PHYs needed for enabling USB OTG mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host-wakeup GPIO is now marked as deprecated in the broadcom-bluetooth
device-tree binding, it's replaced with the host-wakeup interrupt. Update
Tegra device-trees to the recent version of the Bluetooth binding.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The "ak,ak8975" compatible is not recognized by dt-bindings, it's
deprecated. Use supported "asahi-kasei,ak8975" compatible.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With commit c709135e57 ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823b ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2f (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
Before commit 0e30f47232 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.
Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The S5M8767 PMIC does not require anymore a safe DVS voltage, if the DVS
GPIO is not enabled. Although previously bindings required providing
this safe DVS voltage, but since commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") this
was ignored.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210928084949.27939-12-krzysztof.kozlowski@canonical.com
Add compatible values to Ethernet PHY subnodes representing Renesas
uPD60610 or uPD60611 PHYs on RZ/A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/335a1dfea905369da683e122e41e08ca1c5f90f7.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8201FL PHYs on RZ/A2 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/a23eca16869457684b0300379233e335b4e2047e.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing SMSC
LAN8710A PHYs on RZ/A1 and R-Mobile A1 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/247dc2074dae149af07b6d014985ad30eb362eda.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on RZ/G1 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ce8ae6b199fa244315a008ae31891a808ca1948d.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ8041 PHYs on RZ/G1 and R-Car Gen2 boards. This allows software to
identify the PHY model at any time, regardless of the state of the PHY
reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/f9e26625924f90eff34fe6f6f02b15fa272c5d80.1631174218.git.geert+renesas@glider.be
According to schematics, and confirmed by ID_REV register contents, the
Ethernet controllers on various development board are not SMSC LAN9220,
but different variants:
- KZM-A9-Dual and KZM-A9-GT: LAN9221,
- Bock-W and Marzen: LAN89218AQ.
Update the compatible values accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59c142176f795b3541c935df43ab11cecd77cc61.1631173813.git.geert+renesas@glider.be
Commit 078fb7aa6a ("arm: dts: vexpress: Fix addressing issues with
'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress
boards. The problem is #address-cells size changed, but interrupt-map
was not updated. This results in the timer interrupt (and all the
other motherboard interrupts) not getting mapped.
As the 'interrupt-map' properties are all just duplicates across boards,
just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi.
Strictly speaking, 'interrupt-map' is dependent on the parent
interrupt controller, but it's not likely we'll ever have a different
parent than GICv2 on these old platforms. If there was one,
'interrupt-map' can still be overridden.
Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org
Fixes: 078fb7aa6a ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes")
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
The SSI 1328 is a NAS box running a SL3516 SoC.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The edimax NS2502 is a NAS box running a SL3516 SoC.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The micro-SD card doesn't feature a write-protect pin. Set the
corresponding property in the devicetree to handle this behavior
correctly and suppress driver warnings.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- ranges property should be grouped by region, with no functional
changes. Otherwise, schema dtbs_check would report the following errors.
"linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'boolean'
True was expected
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'null'
[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640] is too long
From schema: linux-imx/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml"
- refer to commit 281f1f99cf ("PCI: dwc: Detect number of iATU windows").
The num-viewport is not required anymore, remove them totally.
- dt_binding_check complains "compatible: ['fsl,imx6qp-pcie', 'snps,dw-pcie']
is too long", remove "snps,dw-pcie" from the compatible string.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the ADC nodes to the AST2600 devicetree. Enable ADC1 for Rainier and
Everest systems and add an iio-hwmon node for the 7th channel to report
the battery voltage.
Tested on Rainier:
~# cat /sys/class/hwmon/hwmon11/in1_input
1347
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210916210045.31769-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The following warning is seen when the SPI GPIO driver probes:
gpio-expander@0 enforce active low on chipselect handle
The reason for this warning is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the reg property was added to each channel node in commit
b86d3d21cd ("ARM: dts: imx6dl-yapp4: Add reg property to the lp5562
channel node") it is possible to skip unused channels.
Remove the actually unused white LED channel.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the LED multicolor framework support was added in commit
92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
LEDs on this platform stopped working.
Author of the framework attempted to accommodate this DT to the
framework in commit b86d3d21cd ("ARM: dts: imx6dl-yapp4: Add reg property
to the lp5562 channel node") but that is not sufficient. A color property
is now required even if the multicolor framework is not used, otherwise
the driver probe fails:
lp5562: probe of 1-0030 failed with error -22
Add the color property to fix this.
Fixes: 92a81562e6 ("leds: lp55xx: Add multicolor framework support to lp55xx")
Cc: <stable@vger.kernel.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MAC-Address of the MR32's sole ethernet port is
located in offset 0x66 of the attached AT24C64 eeprom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
the switch identifies itself as a BCM53012 (rev 5)...
This patch has been tested & verified on OpenWrt's
snapshot with Linux 5.10 (didn't test any older kernels).
The MR32 is able to "talk to the network" as before with
OpenWrt's SWITCHDEV b53 driver.
| b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
| libphy: dsa slave smi: probed
| b53-srab-switch 18007000.ethernet-switch poe (uninitialized):
| PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
| b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks.
| Please migrate to PHYLINK!
| DSA: tree 0 setup
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM53573 family SoC have Ethernet switch connected to the first Ethernet
controller (accessible over MDIO).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
To match the new dts binding. Remove "subsys",unused
interrupt and slot node.Add "interrupt-names",
"linux,pci-domain" and pciecfg node.
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20210823032800.1660-7-chuanjia.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The partitions on the eMMC will not even appear sometimes, in the
datasheet for the Samsung KLMxGxxE4x we find that the power-on time
for a 4GB eMMC of this type is 300 ms and nowadays the block stack
is so fast so we are stressing it, and we need to specify that we
need this delay in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new dtsi file for sama5d29 SoC is added which basically inherits the sama5d2
dtsi with the mac controller compatible property updated.
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210812140758.28273-1-Hari.PrasathGE@microchip.com
This went unnoticed until commit 7897b071ac ("net: macb: convert
to phylink") which tickled the problem. The sama5d3 emac has never
been capable of rgmii, and it all just happened to work before that
commit.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/ea781f5e-422f-6cbf-3cf4-d5a7bac9392d@axentia.se
With the conversion of rockchip,rk-timer.yaml the clock-names order
was set to "pclk", "timer", but nothing was fixed in the ARM dts section
of the mainline kernel, so the swap timer clock-names that don't fit.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828102659.7348-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After the conversion to YAML of the Operating Performance Points(OPP)
binding the operating-points property expects values in
a uint32-matrix with 2 items, so fix the notifications by adding
angle brackets.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/opp/opp-v1.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828091233.19992-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After the conversion to YAML of the Operating Performance Points(OPP)
binding the operating-points-v2 property expects the nodename to have
the '^opp-table(-[a-z0-9]+)?$' format, so rename all Rockchip ARM dts
opp-table node names.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/opp/opp-v2.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828094512.26862-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rv1108 gmac node is checked with rockchip-dwmac.yaml,
snps,dwmac.yaml and ethernet-controller.yaml.
The nodename should have a pattern: "^ethernet(@.*)?$",
so change to nodename.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828114240.12231-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The MK808 has a button inside the cover for the boot loader to do
some action. Add the adc-keys node to the rk3066a-mk808.dts file.
The rk3066 has a higher maximum DC supply voltage for the analog part of
SAR-ADC VDDA_SARADC of 2.75V then other Rockchip SoCs.
For the "rockchip,saradc" node is a vref-supply property required,
so add a regulator for it as well.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210828092755.24560-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MT7623 has an musb controller that is compatible with the one from MT2701.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210830155903.13907-2-mans0n@gorani.run
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
According to YAML validation, and for a future patchset putting this
xo_board reference clock to use as VCO reference parent, add the missing
clock to dsi_phy0.
Fixes: 5a9fc531f6 ("ARM: dts: msm8974: add display support")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210830175739.143401-1-marijn.suijten@somainline.org
APQ8064 was last user of gpu-pwrlevels inside mainline tree, so convert
it now.
Tested on Nexus 7 2013, no functional changes.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829133918.57780-3-david@ixit.cz
The legacy clock names (including the _clk suffix) was dropped from the
driver, so update the dts accordingly).
Tested on Nexus 7 2013, no functional changes.
Signed-off-by: David Heidelberg <david@ixit.cz>
[bjorn: Updated commit message]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829133918.57780-2-david@ixit.cz
The 'motherboard-bus' node in Arm Ltd boards fails schema checks as
'simple-bus' child nodes must have a unit-address. The 'ranges' handling is
also wrong (or at least strange) as the mapping of SMC chip selects should
be in the 'arm,vexpress,v2m-p1' node rather than a generic 'simple-bus'
node. Either there's 1 too many levels of 'simple-bus' nodes or 'ranges'
should be moved down a level. The latter change is more simple, so let's do
that. As the 'ranges' value doesn't vary for a given motherboard instance,
we can move 'ranges' into the motherboard dtsi files.
Link: https://lore.kernel.org/r/20210819184239.1192395-6-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add Exegin Q5xR5. The base device tree is from OpenWrt tree and with
the addition of this patch there will be no need to maintain it
separatelly in OpenWrt.
[osk: original author of patch in OpenWrt]
[claudiu.beznea: use "&<label> {" syntax, sorted nodes in alphabetical
order, adapted flash to new support in kernel 5.14, use proper
compatibles according to kernel 5.14, use macros instead of
hardcoded numbers for pinctrl phandles and for all pinctrl references,
add pinctrl-names, pinctrl-X where necessaray]
Signed-off-by: Owen Kirby <osk@exegin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-8-claudiu.beznea@microchip.com
Add CalAmp LMU5000 board. The base device tree is from OpenWrt tree and
with the addition of this patch there will be no need to maintain it
separatelly in OpenWrt.
[porter.adam: original author of patch in OpenWrt]
[claudiu.beznea: fixed compilation warnings, use &<lable> syntax,
sorted nodes in alphabetical order, adapted flash to new support
in kernel 5.14, use proper compatibles according to kernel 5.14,
use macros instead of hard coded numbers for pinctrl phandles and
for all pinctrl references, add pinctrl-names, pinctrl-X where
necessary]
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-5-claudiu.beznea@microchip.com
The ADC controller on the board is fed by a 2.5V reference voltage.
By default the channels #14 and #15 are dedicated to analog input
(marked AN on the board), on the connectors mikrobus1 and mikrobus2.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-11-eugen.hristev@microchip.com
SAMA5D27 WLSOM1 boards has a WILC3000 device soldered. Add proper
device tree nodes for this.
[eugen.hristev: original author of this code]
[claudiu.beznea: adapt such that make dtbs_check is happy, remove status
for wifi_pwrseq and wifi nodes]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[nicolas.ferre: original author of this code]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210825094055.642941-1-claudiu.beznea@microchip.com
Those are remaining models I have that didn't have ports yet. All
tested.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The naming of this node is based upon that of the initial EA9500 dts[1].
However this does not conform with the mdio-mux format, yielding the
following message when running dtbs_check:
mdio-mii-mux: $nodename:0: 'mdio-mii-mux' does not match '^mdio-mux[\\-@]?'
Secondly, this node should be moved to within the axi node and given the
appropriate unit address. This also requires exposing the axi node via a
label in bcm-nsp.dtsi. This fixes the following warning:
Warning (unit_address_vs_reg): /mdio-mii-mux: node has a reg or ranges property, but no unit name
[1]https://patchwork.ozlabs.org/project/linux-imx/patch/20180618174159.86150-1-npcomplete13@gmail.com/#1941353
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Running dtbs_check yields the following message when checking the
MX64/MX65 devicetree:
at24@50: $nodename:0: 'at24@50' does not match '^eeprom@[0-9a-f]{1,2}$'
This patch fixes the issue by renaming the at24 node appropriately.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While functional, the mdio-mux-mmioreg binding does not conform to
Documentation/devicetree/bindings/net/mdio-mux-mmioreg.yaml in that an
mdio-mux compatible is also required. Without this the following output
is observed when running dtbs_check:
mdio-mux@32000: compatible: ['mdio-mux-mmioreg'] is too short
This change brings conformance to this requirement and corresponds
likewise to Rafal Milecki's change to the BCM5301x platform[1].
[1] https://lore.kernel.org/linux-arm-kernel/20210822191256.3715003-1-f.fainelli@gmail.com/T/
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Running dtbs_check yielded the issues with bcm-nsp.dtsi.
Firstly this patch fixes the following message by appending "-bus" to
the mpcore node name:
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Secondly mmc node name. The label name can remain as is.
sdhci@21000: $nodename:0: 'sdhci@21000' does not match '^mmc(@.*)?$'
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This board was previously added to
Documentation/devicetree/bindings/arm/bcm/brcm,nsp.yaml
however the dts file was not updated to reflect this change. This patch
corrects bcm958623hr.dts by adding the board name to the compatible.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This fixes following error for all BCM5301X dts files:
mdio-bus-mux@18003000: compatible: ['mdio-mux-mmioreg'] is too short
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This fixes following errors for all BCM5301X dts files:
chipcommonA@18000000: $nodename:0: 'chipcommonA@18000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
mpcore@19000000: $nodename:0: 'mpcore@19000000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
mdio-bus-mux@18003000: $nodename:0: 'mdio-bus-mux@18003000' does not match '^mdio-mux[\\-@]?'
dmu@1800c000: $nodename:0: 'dmu@1800c000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
MX65 & MX65W Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 switch (2x 1GbE ports)
2x Qualcomm QCA8337 switches (10x 1GbE ports total)
- PSE: Broadcom BCM59111KMLG connected to LAN ports 11 & 12
- USB: 1x USB2.0
- Serial: Internal header
- WLAN(MX65W Only): 2x Broadcom BCM43520KMLG on the PCI bus.
Note that a driver and firmware image for the BCM59111 PSE has been
released under GPL, but this is not present in the kernel.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
MX64 & MX64W Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 internal switch (5x 1GbE ports)
- USB: 1x USB2.0
- Serial: Internal header
- WLAN(MX64W only): 2x Broadcom BCM43520KMLG on the PCI bus
This patch adds the Meraki MX64 series-specific bindings. Since some
devices make use of the older A0 SoC, changes need to be made to
accommodate this case, including removal of coherency options and
modification to the secondary-boot-reg.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While uncommon, some Ax NSP SoCs exist in the wild. This stepping
requires a modified secondary CPU boot-reg and removal of DMA coherency
properties. Without these modifications, the secondary CPU will be
inactive and many peripherals will exhibit undefined behaviour.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
These bindings are required for all Meraki MX64/MX65 devices. These
common bindings include memory (2GB), PWM LEDs, AMAC, I2C (AT24), NAND
partitions, EHCI, OHCI and pinctrl.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch largely replicates Vivek Unune's patch "ARM: dts:
BCM5301X:Make usb3 phy use mdio phy driver"[1] for the NSP platform,
whereby we need to create an mdio-mux to facilitate switches
configured via external MDIO, in this case on the Meraki MX65.
However in doing so, we are creating an overlap with usb3_phy's
ccb-mii range. To resolve this, usb3_phy should be moved to a child
node of the internal MDIO bus. The result is heavily based upon Vivek's
patch. This has also been cross-referenced with Yendapally Reddy's
earlier work which utilised the subsequently dropped brcm,nsp-usb3-phy
driver: "[PATCH v2 4/4] arm: dts: nsp: Add USB nodes to device tree"
[2]. Finally, this change provides conformance to the bcm-ns-usb3-phy
documentation, utilising the required usb3-dmp-syscon property. Note
that support for the deprecated ccb-mii bindings has been dropped as of
"phy: phy-bcm-ns-usb3: drop support for deprecated DT binding"[3].
[1] https://lore.kernel.org/patchwork/patch/933971/
[2] https://www.spinics.net/lists/arm-kernel/msg555132.html
[3] https://lore.kernel.org/linux-devicetree/20201113113423.9466-1-zajec5@gmail.com/
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds the node for the MDIO bus controller, present on the NSP
SoC.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The QSPI bus is enabled by default, however this may not used on all
devices. This patch disables by default, requiring it to be explicitly
enabled where required.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The previous patch "ARM: dts: NSP: Disable PL330 by default, add
dma-coherent property" set the DMAC to disabled by default, requiring it
to be manually enabled on each device. The bcm988312hr was mistakenly
omitted. This patch adds it back.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently only the SoC type and platform are specified for all NSP
devices. This patch adds the device names.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The s6e63m0 display used "type 3" SPI communication so
flag the device as using negative clocking and polarity
on the SPI bus.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without a sensor node, the ISC will simply fail to probe, as the
corresponding port node is missing.
It is then logical to disable the node in the devicetree.
If we add a port with a connection to a sensor endpoint, ISC can be enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210902121358.503589-1-eugen.hristev@microchip.com
Based on 'ranges', the 'bus@4000000' node unit-address is off by 1 '0'.
Link: https://lore.kernel.org/r/20210819184239.1192395-5-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Drop the '#interrupt-cells' property in the motherboard node which has no
effect as the node is neither an interrupt-controller or interrupt-map
(that's in the parent node).
Drop 'model' as it is not used by software nor documented.
Drop 'arm,v2m-memory-map' as it is not used by software. The purpose was
to describe which memory map, but that's all described by the DT
already.
Link: https://lore.kernel.org/r/20210819184239.1192395-4-robh@kernel.org
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Align the watchdog and mmc device node names with the schema to fix
warnings like:
mmci@50000: $nodename:0: 'mmci@50000' does not match '^mmc(@.*)?$'
wdt@f0000: $nodename:0: 'wdt@f0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Link: https://lore.kernel.org/r/20210820081733.83976-2-krzysztof.kozlowski@canonical.com
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The state of this GPIO determines whether a factory reset has been
requested. If a physical switch is used, it can be high or low. During boot,
the software checks and records the state of this switch. If it is different
than the previous recorded state, then the read-write portions of memory are
reformatted.
Signed-off-by: Isaac Kurth <isaac.kurth@ibm.com>
Link: https://lore.kernel.org/r/20210901185236.558771-1-isaac.kurth@ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a device tree for the LG G Watch R smartwatch, manufactured by LG
Electronics and based on the msm8226 platform (apq8026).
Currently UART, internal storage, power button and touchscreen are
supported.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
[bjorn: Moved "rpm_requests" before "sdhc", to keep things sorted]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210911232707.259615-9-luca@z3ntu.xyz
Add nodes for sdhc, uart4, i2c, scm, smem, rpm-requests including
dependencies.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
[bjorn: Moved other nodes before "soc" to keep things alphabetical]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210911232707.259615-5-luca@z3ntu.xyz
The 28NM DSI PLL driver for msm8960 calculates with a 27MHz reference
clock and should hence use PXO, not CXO which runs at 19.2MHz.
Note that none of the DSI PHY/PLL drivers currently use this "ref"
clock; they all rely on (sometimes inexistant) global clock names and
usually function normally without a parent clock. This discrepancy will
be corrected in a future patch, for which this change needs to be in
place first.
Fixes: 6969d1d9c6 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20210829203027.276143-2-marijn.suijten@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Also resolves these kernel warnings for APQ8064:
adreno 4300000.adreno-3xx: Using legacy qcom,chipid binding!
adreno 4300000.adreno-3xx: Use compatible qcom,adreno-320.2 instead.
Tested on Nexus 7 2013, no functional changes.
Cc: <stable@vger.kernel.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210818065317.19822-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Allwinner R40 has 3 I2S controllers, compatible to those in H3. First
two are routed to pins, while third is used internally for HDMI audio.
Add nodes for all 3 I2S controllers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210912072914.398419-3-jernej.skrabec@gmail.com
The dumb-vga-dac and adi,adv7123 compatibles are not supposed to be used
together according to the binding.
Since the corpro gm7123 is a drop-in replacement for the adv7123, let's
remove dumb-vga-dac from our compatible list.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-47-maxime@cerno.tech
The edt,edt-ft5x06 compatible has never been a valid compatible
according to the binding. Let's change for one that is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-46-maxime@cerno.tech
According to the SPI NOR bindings, the flash node names are supposed to
be flash@<address>. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-44-maxime@cerno.tech
The operating-points-v2 nodes are named inconsistently, but mostly
either opp_table0 or gpu-opp-table. However, the underscore is an
invalid character for a node name and the thermal zone binding
explicitly requires that zones are called opp-table-*. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-43-maxime@cerno.tech
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each OPP, which in
turns create a validation warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-42-maxime@cerno.tech
We've had a pinctrl node name convention for a while now, let's follow
it for the AXP pinctrl nodes as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-41-maxime@cerno.tech
The name of our PMIC power supply names conflict with the generic
regulator supply check that matches anything called *-supply, including
the nodes, and then makes sure it's a phandle.
A node is obviously not a phandle, so let's change our power supplies
names to avoid any conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-40-maxime@cerno.tech
- Add new cpufreq driver for the MediaTek MT6779 platform called
mediatek-hw along with corresponding DT bindings (Hector.Yuan).
- Add DCVS interrupt support to the qcom-cpufreq-hw driver (Thara
Gopinath).
- Make the qcom-cpufreq-hw driver set the dvfs_possible_from_any_cpu
policy flag (Taniya Das).
- Blocklist more Qualcomm platforms in cpufreq-dt-platdev (Bjorn
Andersson).
- Make the vexpress cpufreq driver set the CPUFREQ_IS_COOLING_DEV
flag (Viresh Kumar).
- Add new cpufreq driver callback to allow drivers to register
with the Energy Model in a consistent way and make several
drivers use it (Viresh Kumar).
- Change the remaining users of the .ready() cpufreq driver callback
to move the code from it elsewhere and drop it from the cpufreq
core (Viresh Kumar).
- Revert recent intel_pstate change adding HWP guaranteed performance
change notification support to it that led to problems, because
the notification in question is triggered prematurely on some
systems (Rafael Wysocki).
- Convert the OPP DT bindings to DT schema and clean them up while
at it (Rob Herring).
-----BEGIN PGP SIGNATURE-----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=WSpr
-----END PGP SIGNATURE-----
Merge tag 'pm-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly ARM cpufreq driver updates, including one new
MediaTek driver that has just passed all of the reviews, with the
addition of a revert of a recent intel_pstate commit, some core
cpufreq changes and a DT-related update of the operating performance
points (OPP) support code.
Specifics:
- Add new cpufreq driver for the MediaTek MT6779 platform called
mediatek-hw along with corresponding DT bindings (Hector.Yuan).
- Add DCVS interrupt support to the qcom-cpufreq-hw driver (Thara
Gopinath).
- Make the qcom-cpufreq-hw driver set the dvfs_possible_from_any_cpu
policy flag (Taniya Das).
- Blocklist more Qualcomm platforms in cpufreq-dt-platdev (Bjorn
Andersson).
- Make the vexpress cpufreq driver set the CPUFREQ_IS_COOLING_DEV
flag (Viresh Kumar).
- Add new cpufreq driver callback to allow drivers to register with
the Energy Model in a consistent way and make several drivers use
it (Viresh Kumar).
- Change the remaining users of the .ready() cpufreq driver callback
to move the code from it elsewhere and drop it from the cpufreq
core (Viresh Kumar).
- Revert recent intel_pstate change adding HWP guaranteed performance
change notification support to it that led to problems, because the
notification in question is triggered prematurely on some systems
(Rafael Wysocki).
- Convert the OPP DT bindings to DT schema and clean them up while at
it (Rob Herring)"
* tag 'pm-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
Revert "cpufreq: intel_pstate: Process HWP Guaranteed change notification"
cpufreq: mediatek-hw: Add support for CPUFREQ HW
cpufreq: Add of_perf_domain_get_sharing_cpumask
dt-bindings: cpufreq: add bindings for MediaTek cpufreq HW
cpufreq: Remove ready() callback
cpufreq: sh: Remove sh_cpufreq_cpu_ready()
cpufreq: acpi: Remove acpi_cpufreq_cpu_ready()
cpufreq: qcom-hw: Set dvfs_possible_from_any_cpu cpufreq driver flag
cpufreq: blocklist more Qualcomm platforms in cpufreq-dt-platdev
cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support
cpufreq: scmi: Use .register_em() to register with energy model
cpufreq: vexpress: Use .register_em() to register with energy model
cpufreq: scpi: Use .register_em() to register with energy model
dt-bindings: opp: Convert to DT schema
dt-bindings: Clean-up OPP binding node names in examples
ARM: dts: omap: Drop references to opp.txt
cpufreq: qcom-cpufreq-hw: Use .register_em() to register with energy model
cpufreq: omap: Use .register_em() to register with energy model
cpufreq: mediatek: Use .register_em() to register with energy model
cpufreq: imx6q: Use .register_em() to register with energy model
...
no core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAmEw+3cACgkQQRCzN7AZ
XXOBihAAyVGtmXsEO9yO50R0+RzbTvD8QVGTdBqjSK/ILghoP5xRZzYkOt9oKUgG
2ue24euJ2Ww0+tV69CEKHOfTt8vnXEawQe9hiROQTgSDrT+9ScdT81pEQPH00smM
oQJqxXmi0HQ28r6NyrA/0WN6f0J+nEh7f4STPWtSW8E3Cz/pyODhrtdhyNXbzMJ3
W9JGjTsz4VBy7qurb0RKpQrZ244uDyFCMzZnoBvJBN/f6Jupu09d0mNkDrYhvK5z
FVdIwFEZ2sssF9zf33BkJ7BKnHa5WANJD3RaM2fcCC/sFIq8k3ZVHhvOkdE3QmLp
yWrFZREsJvvK1U/ksHRFB3RucOMKVAXV+CnVxKqTU7rv+cEHH0l/TacPqfZaONm9
LGF3FoGYnG5oO+CxtfAedpHmajDZZNky2RC0Eov/Eigiq+VHXpuClB/DcpHyCuv2
aKDxeqP8JXsZW1t7YutCb6w5f6f8SKC/csaFkMqCJMXz10sCPjKBsvlgWq49A99X
CtwJxlzDKI7i9TSffCTHYUQBWAYa/b3fwnwuVphzpVya1gERvHN30ZhJH9ho0LGW
YNNdVAvqNdH6FzyTzOY8fOKc/J2OY1Yd7gL35T0xYiTrT8JK7rwW8pUh0JINxSdU
QGHjis4WjGUFzgqUpC8qhI6u+rInLRr08sGJ/qnj5TmpZRp9rsk=
=I6N/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
As usual, the bulk of work in the SoC tree goes into DT files,
this time with a roughly even split between 32-bit and 64-bit
SoCs rather than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new
32-bit platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the
existing phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of
older Renesas SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper,
Elbert and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhL13Z5t5GS2LDRf4RAljwAJ0acTxOBYP8J5zETlAQRWYcYWh5hACfZOgC
Om6K0IN5+lJuaUyF/GdmqS4=
=zXua
-----END PGP SIGNATURE-----
Merge tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, the bulk of work in the SoC tree goes into DT files, this
time with a roughly even split between 32-bit and 64-bit SoCs rather
than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new 32-bit
platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the existing
phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of older Renesas
SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper, Elbert
and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions"
* tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (412 commits)
arm/arm64: dts: Fix remaining dtc 'unit_address_format' warnings
ARM: dts: rockchip: Add SFC to RV1108
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
ARM: dts: aspeed: p10bmc: Add power control pins
ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
ARM: dts: aspeed: minipack: Update flash partition table
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
dt-bindings: vendor-prefixes: add Traverse Technologies
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
...
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here, notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanna labs driver updates in this pull request,
that will probably come later before -rc1 is out in a different request.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+Kyw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymlpACg0JM+hSeo8T5GtwZksZ1QXXQfh8sAoK6Dt6xF
e62OQuuMFT0Un0qOflZk
=emH+
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
Pull operating performance points (OPP) framework changes for v5.15
from Viresh Kumar:
"This moves the OPP bindings to DT schema (Rob Herring)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
dt-bindings: opp: Convert to DT schema
dt-bindings: Clean-up OPP binding node names in examples
ARM: dts: omap: Drop references to opp.txt
Fix all the remaining dtc 'unit_address_format' warnings except for the ones
related to 'register-bit-led'. For those, we need to decide on and document
the node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210823165126.2320910-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
opp.txt is getting removed with the OPP binding converted to DT schema.
As it is unusual to reference a binding doc from a dts file, let's just
remove the reference.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a devicetree entry for the Rockchip SFC for the RV1108 SOC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20210812134546.31340-5-jon.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- New machines
* Facebook's Cloudripper
* Facebook's Elbert
* Facebook's Fuji
All three carry the description of "Facebook's next generation switch
platform with an AST2600 BMC integrated for health monitoring
purpose."
They share a 128 MB SPI NOR flash layout that is also used by some
older platforms.
* Inspur's NF5280M6, an x86 platform server with an AST2500-based BMC
- SGPIO updates including AST2600 support
- GPIO descriptions for the IBM AST2600 machines
- Pinctrl fix
- Updates to Facebook's AST2500 based machines
-----BEGIN PGP SIGNATURE-----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=GIHt
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Y4SA
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.15-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 5.15
- New machines
* Facebook's Cloudripper
* Facebook's Elbert
* Facebook's Fuji
All three carry the description of "Facebook's next generation switch
platform with an AST2600 BMC integrated for health monitoring
purpose."
They share a 128 MB SPI NOR flash layout that is also used by some
older platforms.
* Inspur's NF5280M6, an x86 platform server with an AST2500-based BMC
- SGPIO updates including AST2600 support
- GPIO descriptions for the IBM AST2600 machines
- Pinctrl fix
- Updates to Facebook's AST2500 based machines
* tag 'aspeed-5.15-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc: (23 commits)
ARM: dts: aspeed: p10bmc: Add power control pins
ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
ARM: dts: aspeed: minipack: Update flash partition table
ARM: dts: aspeed: Add Facebook Fuji (AST2600) BMC
ARM: dts: aspeed: Add Facebook Elbert (AST2600) BMC
ARM: dts: aspeed: Add Facebook Cloudripper (AST2600) BMC
ARM: dts: aspeed: Common dtsi for Facebook AST2600 Network BMCs
ARM: dts: aspeed: wedge400: Use common flash layout
ARM: dts: Add Facebook BMC 128MB flash layout
ARM: dts: aspeed-g5: Remove ngpios from sgpio node.
ARM: dts: aspeed-g6: Add SGPIO node.
dt-bindings: aspeed-sgpio: Add ast2600 sgpio
dt-bindings: aspeed-sgpio: Convert txt bindings to yaml.
ARM: dts: aspeed: ast2500evb: Enable built in RTC
ARM: dts: aspeed: tacoma: Add TPM reset GPIO
ARM: dts: rainier, everest: Add TPM reset GPIO
ARM: dts: aspeed: wedge100: Enable ADC channels
ARM: dts: aspeed: galaxy100: Remove redundant ADC device
ARM: dts: aspeed: wedge40: Remove redundant ADC device
ARM: dts: aspeed: Enable ADC in Facebook AST2400 common dtsi
...
Link: https://lore.kernel.org/r/CACPK8XdWRBb9cuDWGQPfK8R8TsZuydJQHsL4_e2w=HvCKAMogg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This introduces the MSM8226 platform and an initial dts for the Samsung
Galaxy S III Neo phone.
MSM8974 gains another UART and this is used to enable Bluetooth on the
Sony Xperia Z2 Tablet. Samsung Galaxy S5 gains regulator definitions for
audio and modem remoteprocs, effectively enabling these.
DSI clocks on APQ8064 are updates as the old legacy clock names are no
longer supported by the driver. And IPQ806x GMAC nodes gains AHB resets
wired up.
Lastly APQ8060 is converted to a SPDX header and the ethernet node is
updates in accordance with the binding.
-----BEGIN PGP SIGNATURE-----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=JynD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEbgcEACgkQmmx57+YA
GNlC0Q//USmb8u05Sn7DlYu46UBcNcQrgGOCXIrNWkERm7jxEhUqp4soI24jomiq
1GEKWApzPlmLtBvQKiGl5IoCypYbZ0kOyFBP+FYezmSD8vCU46UtnzKV+b3mzwQH
rDPFogjj92LBv1+i+8jgry3tvrdK3oM2QJ2cSIF7EyXjuMBok36zXdPpG4mP8dBT
vla+IZFa7GXOi+SKVykB8tlaGPaslamIfG6ZtjeJJuGsPRDotjmjc9vvGEtKfOF0
cHKKTtPli60NqwHX61UURNAcaoURBw4W4Jy0KolvMWo98I+TyWf18xRF2aanm8pa
mLsK7SlqipRY1ofTeHZwb6eK3j13qD5knv+tWjjwCTCmAufljnLwqoP494mHeU5D
ppLMcSfw9HheR/J3NoimcJ8mvWe2/NOmtqxKFt0QYUiL3p0uqZUfclTUbIUEqzi3
v30lFh984aB91HgLQkl3dgqmCG/ggS7gy1W2BEQZtsaQHAW4v+psYAjMMMGpkcZV
vHjWffic3y+mVgClZ8PRaqkXQB/IjfuoSF/+VT6/kTNosmOXkvphd3je2ogE9Zn8
4r+ALaAlmaRLpBzvfDTyNAB2gUi4ar22JVa5VpF1y4G9SAlHkv6TdpnaTgfw4SKu
D3fqjSlYJ6DL7CRB+4BetPn2Al83CvuPXSMRF9iuikllRGHZfbs=
=zDwv
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm dts updates for v5.15
This introduces the MSM8226 platform and an initial dts for the Samsung
Galaxy S III Neo phone.
MSM8974 gains another UART and this is used to enable Bluetooth on the
Sony Xperia Z2 Tablet. Samsung Galaxy S5 gains regulator definitions for
audio and modem remoteprocs, effectively enabling these.
DSI clocks on APQ8064 are updates as the old legacy clock names are no
longer supported by the driver. And IPQ806x GMAC nodes gains AHB resets
wired up.
Lastly APQ8060 is converted to a SPDX header and the ethernet node is
updates in accordance with the binding.
* tag 'qcom-dts-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add ahb reset to ipq806x-gmac
ARM: dts: qcom: Fix up APQ8060 DragonBoard license
ARM: dts: qcom: msm8974: castor: Add Bluetooth-related nodes
ARM: dts: qcom: msm8974: Add blsp2_uart7 for bluetooth on sirius
ARM: dts: qcom: Add initial DTS file for Samsung Galaxy S III Neo phone
dt-bindings: arm: qcom: Document MSM8226 SoC binding
ARM: dts: qcom: Add support for MSM8226 SoC
ARM: dts: qcom: apq8060: Correct Ethernet node name and drop bogus irq property
ARM: dts: qcom: apq8064: correct clock names
ARM: dts: qcom: msm8974-klte: Enable remote processors
Link: https://lore.kernel.org/r/20210816211957.579365-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Christoph Niedermaier to clean up i.MX6 DHCOM support.
- New board support: DHCOM based PicoITX, DHSOM based DRC02, SolidRun
SolidSense, SKOV i.MX6 boards.
- Add WiFi support for i.MX7D base reMkarkable2 device.
- Add FTM devices for i.MX7 to have Flex Timers support.
- Configure ENET_REF clock to 125MHz for imx6qp-prtwd3 to support RGMII
PHY mode.
- Drop unneeded #address-cells and #size-cells from vf610-zii SPI EEPROM
device node.
- Add missing USB OTG OC pinmux and Crypto device for i.MX6QDL Gateworks
boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmEXodgUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7/DQf6Ah9P+NmuvrV3T/soI3c6CNdvS4dC
mUqzkdpPvKw4b38iLBNS/qB1JvkIosu84Hx/Ll+toJYWC4QaV9M/ZgnMnqSXN56O
j18CMKhDQrw+Y7jghoqm8kvgmHooaSFvNgMBVNULa2pEozJuN/viUglgVJ+FCYaF
JBO2YRHNZvq0BxEy63es3qGG1JXdfs4slKu2wl4lGRCwk999odQKMFVpe1AaAJzN
sa61EYFsIvCgJGTYQlB6E0CTBkS8R4V4jezNPgGznQjYzCx1OF2+y0HaTUVC0Zk4
qqJcMO0uxFvuXs4dim9/djdmD80oqiGdZG6auPXUtx07MbyOP42dg9EuPA==
=5rPD
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=7FFL
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree changes for 5.15:
- A series from Christoph Niedermaier to clean up i.MX6 DHCOM support.
- New board support: DHCOM based PicoITX, DHSOM based DRC02, SolidRun
SolidSense, SKOV i.MX6 boards.
- Add WiFi support for i.MX7D base reMkarkable2 device.
- Add FTM devices for i.MX7 to have Flex Timers support.
- Configure ENET_REF clock to 125MHz for imx6qp-prtwd3 to support RGMII
PHY mode.
- Drop unneeded #address-cells and #size-cells from vf610-zii SPI EEPROM
device node.
- Add missing USB OTG OC pinmux and Crypto device for i.MX6QDL Gateworks
boards.
* tag 'imx-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (23 commits)
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
ARM: dts: imx7: add ftm nodes for Flex Timers
ARM: dts: imx6qdl-dhcom: Add DHSOM based DRC02 board
ARM: dts: imx6qdl-dhcom: Add DHCOM based PicoITX board
ARM: dts: imx6qdl-dhcom: Split SoC-independent parts of DHCOM SOM and PDK2
ARM: dts: imx6q-dhcom: Cleanup of the devicetrees
ARM: dts: imx6q-dhcom: Rearrange of iomux
ARM: dts: imx6q-dhcom: Rework of the DHCOM GPIO pinctrls
ARM: dts: imx6q-dhcom: Use 1G ethernet on the PDK2 board
ARM: dts: imx6q-dhcom: Set minimum memory size of all DHCOM i.MX6 variants
ARM: dts: imx6q-dhcom: Remove ddc-i2c-bus property
ARM: dts: imx6q-dhcom: Add keys and leds to the PDK2 board
ARM: dts: imx6q-dhcom: Align stdout-path with other DHCOM SoMs
ARM: dts: imx6q-dhcom: Adding Wake pin to the PCIe pinctrl
ARM: dts: imx6q-dhcom: Fill GPIO line names on DHCOM SoM
ARM: dts: imx6q-dhcom: Add interrupt and compatible to the ethernet PHY
ARM: dts: imx6q-dhcom: Add the parallel system bus
ARM: dts: imx7d-remarkable2: Add WiFi support
...
Link: https://lore.kernel.org/r/20210814133853.9981-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The majority of this is temperature sensor additions for various devices
and fixes to the trigger type of the thermal interrupts.
Other than that there are various minor fixes across the board.
-----BEGIN PGP SIGNATURE-----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=8RvP
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=zHxH
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.15-rc1
The majority of this is temperature sensor additions for various devices
and fixes to the trigger type of the thermal interrupts.
Other than that there are various minor fixes across the board.
* tag 'tegra-for-5.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tamonten: Fix UART pad setting
ARM: tegra: nexus7: Improve thermal zones
ARM: tegra: acer-a500: Improve thermal zones
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
ARM: tegra: acer-a500: Add power supplies to accelerometer
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
ARM: tegra: acer-a500: Add interrupt to temperature sensor node
ARM: tegra: nexus7: Add interrupt to temperature sensor node
ARM: tegra: paz00: Add interrupt to temperature sensor node
ARM: tegra: ouya: Add interrupt to temperature sensor node
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
Link: https://lore.kernel.org/r/20210813162157.2820913-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add some comments to explain the purpose of "mdio1" controller: it's
connected to the MDC/MDIO interface of the on-board management switch.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210813061900.24539-1-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
By default ENET_REF is configured to 50MHz, which is usable for the RMII
link. In case RGMII is used, we need 125MHz clock.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove #address-cells and #size-cells property from at93c46d device tree
node as it does not have child nodes.
Fixes: 1556063fde ("ARM: dts: vf610-zii-dev: Add ZII development board.")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use skin temperature for maintaining temperature that is suitable
specifically for Nexus 7. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use skin temperature for maintaining temperature that is suitable
specifically for A500. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The verbose variant of the atmel,wakeup-method value was lost when patch
that added the property was merged because it conflicted with other patch,
re-add it for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor and enable it in pinmux,
for completeness.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU
temperature reporting and thermal throttling is available on all Tegra30
devices universally.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add initial version of device tree for Facebook Fuji (AST2600) BMC.
Fuji is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-7-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Elbert (AST2600) BMC.
Elbert is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-6-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Cloudripper (AST2600) BMC.
Cloudripper is Facebook's next generation switch platform with an AST2600
BMC integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This common descirption is included by all Facebook AST2600 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify wedge400 flash layout by using the common layout defined in
"facebook-bmc-flash-layout-128.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 128MB mtd device.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
A series of changes to update am3 to use cpsw switch driver and
few updates to earlier SanCloud changes. The plan was to send the
cpsw switch driver changes earlier but looks like I never tagged
the mail thread in my inbox to apply for v5.15.
-----BEGIN PGP SIGNATURE-----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=qPV9
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=7Hv9
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for am3 cpsw and SanCloud for v5.15
A series of changes to update am3 to use cpsw switch driver and
few updates to earlier SanCloud changes. The plan was to send the
cpsw switch driver changes earlier but looks like I never tagged
the mail thread in my inbox to apply for v5.15.
* tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-sancloud-bbe: Drop usb wifi comment
ARM: dts: am335x-sancloud-bbe: Fix missing pinctrl refs
ARM: dts: am335x-bone: switch to new cpsw switch drv
ARM: dts: am33xx: update ethernet aliases
ARM: dts: am335x-sl50: switch to new cpsw switch drv
ARM: dts: am335x-shc: switch to new cpsw switch drv
ARM: dts: am335x-phycore: switch to new cpsw switch drv
ARM: dts: am335x-pepper: switch to new cpsw switch drv
ARM: dts: am335x-pdu001: switch to new cpsw switch drv
ARM: dts: am335x-osd3358-sm-red: switch to new cpsw switch drv
ARM: dts: am335x-myirtech: switch to new cpsw switch drv
ARM: dts: am335x-moxa-uc: switch to new cpsw switch drv
ARM: dts: am335x-lxm: switch to new cpsw switch drv
ARM: dts: am335x-igep0033: switch to new cpsw switch drv
ARM: dts: am335x-cm-t335: switch to new cpsw switch drv
ARM: dts: am335x-chiliboard: switch to new cpsw switch drv
ARM: dts: am335x-nano: switch to new cpsw switch drv
ARM: dts: am335x-baltos: switch to new cpsw switch drv
Link: https://lore.kernel.org/r/pull-1628751694-126144@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix up some (non-urgent) IRQ flags for the PCI buses.
- Add the second UART to the generic ixp4xx.dtsi
- Make use of the new expansion bus driver in all device
trees with e.g. flash memory on the expansion bus.
- Adds the CF card slot to the Gateworks GW2358.
- Add new device trees for:
- Iomega NAS 100D
- D-Link DSM-G600
- Netgear WG302v2
- Arcom Vulcan
- Gateworks Avila GW2348
- Intel IXPD425 and siblings
- Coyote and IXDPG425
- Linksys WRV54G
-----BEGIN PGP SIGNATURE-----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=ig2J
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=8Yz2
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-dts-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
IXP4xx DTS file updates for the v5.15 kernel cycle:
- Fix up some (non-urgent) IRQ flags for the PCI buses.
- Add the second UART to the generic ixp4xx.dtsi
- Make use of the new expansion bus driver in all device
trees with e.g. flash memory on the expansion bus.
- Adds the CF card slot to the Gateworks GW2358.
- Add new device trees for:
- Iomega NAS 100D
- D-Link DSM-G600
- Netgear WG302v2
- Arcom Vulcan
- Gateworks Avila GW2348
- Intel IXPD425 and siblings
- Coyote and IXDPG425
- Linksys WRV54G
* tag 'ixp4xx-dts-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Add a devicetree for Freecom FSG-3
ARM: dts: ixp4xx: Add devicetree for Linksys WRV54G
ARM: dts: ixp4xx: Add device trees for Coyote and IXDPG425
ARM: dts: ixp4xx: Add Intel IXDP425 etc reference designs
ARM: dts: ixp4xx: Add CF to GW2358
ARM: dts: ixp4xx: Add Gateworks Avila GW2348 device tree
ARM: dts: ixp4xx: Add Arcom Vulcan device tree
ARM: dts: ixp4xx: Add devicetree for Netgear WG302v2
ARM: dts: ixp4xx: Use the expansion bus
ARM: dts: ixp4xx: Add second UART
ARM: dts: ixp4xx: Add devicetree for D-Link DSM-G600 rev A
ARM: dts: ixp4xx: Move EPBX100 flash to external bus node
ARM: dts: ixp4xx: Add devicetree for Iomega NAS 100D
ARM: dts: ixp4xx: Fix up bad interrupt flags
Link: https://lore.kernel.org/r/CACRpkdY19AvWT--OcmEKbwFue_EcThVs7uZeHkzORten7xj-RA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
