atmel,adc-res, atmel,adc-res-names and the trigger nodes are not parsed by
the driver anymore and the information is now defined in the driver data.
Also remove the leftover #address-cells and #size-cells that were used when
the trigger nodes had a unit-address.
Finally, the default is already to use the highest resoution. Remove
atmel,adc-use-res from the SoC dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-11-alexandre.belloni@bootlin.com
The ADC is different from the at91sam9x5 ADC. Not only it doesn't have the
same resolution but it even has only one and the LOWRES bit doesn't exist.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-9-alexandre.belloni@bootlin.com
Things are wired up for powersaving, so lets use the corresponding
compatible and also update a deprecated property name.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AES needs to be disabled on Nokia N950/N9 as well (HS devices), otherwise
kernel fails to boot.
Fixes: c312f06631 ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch amam335x-evm, am335x-evmsk and am335x-icev2 boards to use new
cpsw switch driver. Those boards have or 2 Ext. port wired and configured
in dual_mac mode by default, or only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT node for the new cpsw switchdev based driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 'eth_switch' name has been misspelled in the imx28.dtsi file,
so this change fixes it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Protonic WD3 is a proof of concept platform for tractor e-cockpit applications
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the correct pin for the i2c scl signal else we can't access the
SoM eeprom.
Fixes: 2a51f9dae1 ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Bernd Bauer <bernd.bauer@anton-paar.com>
[m.felsch@pengutronix.de: Adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set it to max. allowed 375kHz for faster transfers. The limit is given
by the erratum [1].
[1] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 8ad2d1dcce ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera
support") the PAD_GPIO_6 is used for providing the camera sensor clock.
Remove it from the enetgrp to fix the following IOMXU conflict:
[ 9.972414] imx6q-pinctrl 20e0000.pinctrl: pin MX6Q_PAD_GPIO_6 already requested by 2188000.ethernet; cannot claim for 1-003c
[ 9.983857] imx6q-pinctrl 20e0000.pinctrl: pin-140 (1-003c) status -22
[ 9.990514] imx6q-pinctrl 20e0000.pinctrl: could not request pin 140 (MX6Q_PAD_GPIO_6) from group ov5645grp on device 20e0000.pinctrl
Fixes: 8ad2d1dcce ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
New drivers:
- SoC info driver to expose revision information
New features:
- AST2600 support for the LPC control driver. This includes
setting the LPC2AHB bridge up in a backwards compatible manner.
Cleanups:
- LPC control
- Kconfig
- Bindings updates for AST2600 strings
-----BEGIN PGP SIGNATURE-----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=KcaK
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/drivers
ASPEED soc driver updates for 5.11
New drivers:
- SoC info driver to expose revision information
New features:
- AST2600 support for the LPC control driver. This includes
setting the LPC2AHB bridge up in a backwards compatible manner.
Cleanups:
- LPC control
- Kconfig
- Bindings updates for AST2600 strings
* tag 'aspeed-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
soc: aspeed: Enable drivers with ARCH_ASPEED
soc: aspeed: Fix a reference leak in aspeed_socinfo_init()
soc: aspeed: remove unneeded semicolon
soc: aspeed-lpc-ctrl: Fix driver name
soc: aspeed-lpc-ctrl: Fix whitespace
soc: aspeed-lpc-ctrl: LPC to AHB mapping on ast2600
soc: aspeed-lpc-ctrl: Fail probe of lpc-ctrl if reserved memory is not aligned
soc: aspeed: lpc: Add AST2600 compatible strings
dt-bindings: aspeed-lpc: Add AST2600 compatible strings
ARM: dts: aspeed: Add silicon id node
soc: aspeed: Add soc info driver
dt-bindings: aspeed: Add silicon id node to SCU
soc: aspeed: Improve kconfig
Link: https://lore.kernel.org/r/CACPK8Xe=9ezhyWRMqVOEQr7SU1YoYfVBGGdGzjmE4SiBr--vJQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree for RD-AC3X-48G4X2XL board. This has a Armada 382 SoC on
a interposer board connected to a baseboard with a Prestera AC3X ASIC
connected via PCI.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Rockchip RK3288 and RK3399Pro based VMARC SOM has sdio0 for
connecting WiFi/BT devices as a pluggable card via M.2 E-Key.
Add associated sdio0 nodes, properties.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201023181814.220974-2-jagan@amarulasolutions.com
[moved the unrelated rtc addition to a separate patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the hym8563 rtc found on the rk3288 variant of the VMARC SOM.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201023181814.220974-2-jagan@amarulasolutions.com
[split out of the original patch, as it was a change unrelated
to the commit description]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm/boot/dts/rv1108-evb.dt.yaml:
wdt@10360000: $nodename:0: 'wdt@10360000'
does not match '^watchdog(@.*|-[0-9a-f])?$'
Fix it by renaming the wdt nodename to watchdog
in the rv1108.dtsi file.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201116150756.14265-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only nodes which have status = "disabled" defined from included files
need status = "okay".
The ethernet-phy node and the i2cmux node do not need it, since they are
wholly defined here.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Rename the node from "phy@1" to "ethernet-phy@1", since "phy@1" is
incorrect according to device-tree bindings documentation.
Also remove the "ethernet-phy-id0141.0DD1" compatible string, it is not
needed. Kernel can read the PHY identifier itself.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Linux now has incomplete support for the LED controller on Turris Omnia:
it can set brightness and colors for each LED.
The controller can also put these LEDs into HW controlled mode, in which
the LEDs are controlled by HW: for example the WAN LED is connected via
MCU to the WAN PHY LED pin.
The driver does not support these HW controlled modes yet, and on probe
puts the LEDs into SW controlled mode.
Add node describing the LED controller, but disable it for now.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Turris Omnia has an SFP cage that, together with WAN PHY, is connected
to eth2 SerDes via a SerDes multiplexor. When a SFP module is present,
the multiplexor switches the SerDes signal from PHY to SFP.
Describe the SFP cage, but leave it disabled. Until phylink has support
for such configuration, we are leaving it to U-Boot to enable SFP and
disable WAN PHY at boot time depending on whether a SFP module is
present.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Describe switch interrupt for Turris Omnia so that the CPU does not have
to poll the switch. We also need to to set mpp45 pin to gpio function
for this.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The eth2 controller on Turris Omnia is connected to SerDes. For SFP to
be able to switch between 1G and 2.5G modes the comphy link has to be
defined.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a6a9f370 ("ARM: dts: add description for Armada 38x ...")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The buffer manager is available on Turris Omnia but needs to be
described in device-tree to be used.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This adds support for the OMNIA Flex Concentrator product
from Kamstrup A/S. It's providing radio mesh communication
infrastructure for smart electricity meters.
Kamstrup OMNIA is a modular and scalable smart grid platform.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the calibration table to make the temperature more accurate.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The range of dcfg reg is wrong, which overlap with other device,
such as rcpm. This issue causing rcpm driver failed to claim
reg resource when calling devm_ioremap_resource().
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The data of property 'fsl,rcpm-wakeup' is not corrcet, which causing
RCPM driver incorrectly program register IPPDEXPCR1, then flextimer is
wrongly clock gated during system suspend, can't send interrupt to
wake.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pinctrl information for the 98dx3236 (and variants). There is only
one choice for i2c0 MPP14 and MPP15.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba877 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS305-1G-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This property is used by io-channel consumers, not providers so should
not present here. Note dt_schema will now detect this error as there
is a dependency between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201115192951.1073632-7-jic23@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Another set of patches for devicetree files and Arm
SoC specific drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including
one regression for the CPSW network driver and a few
runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform,
in particular fixing the MMC device ordering that
recently became nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including
a regression fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the
NXP dpio driver
- A regression fix for a bug caused by an earlier bug
fix in the xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the
NXP LPC32xx platform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=yGOq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of patches for devicetree files and Arm SoC specific
drivers:
- A fix for OP-TEE shared memory on non-SMP systems
- multiple code fixes for the OMAP platform, including one regression
for the CPSW network driver and a few runtime warning fixes
- Some DT patches for the Rockchip RK3399 platform, in particular
fixing the MMC device ordering that recently became
nondeterministic with async probe.
- Multiple DT fixes for the Tegra platform, including a regression
fix for suspend/resume on TX2
- A regression fix for a user-triggered fault in the NXP dpio driver
- A regression fix for a bug caused by an earlier bug fix in the
xilinx firmware driver
- Two more DTC warning fixes
- Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
platform"
* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
arm64: tegra: Fix Tegra234 VDK node names
arm64: tegra: Wrong AON HSP reg property size
arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
arm64: tegra: Correct the UART for Jetson Xavier NX
arm64: tegra: Disable the ACONNECT for Jetson TX2
optee: add writeback to valid memory type
firmware: xilinx: Use hash-table for api feature check
firmware: xilinx: Fix SD DLL node reset issue
soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
MAINTAINERS: Remove myself as LPC32xx maintainers
arm64: dts: qcom: clear the warnings caused by empty dma-ranges
arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
...
This adds support for the Tegra30-based Ouya game console and enhances a
number of existing device trees. It also fixes a couple of minor issues
that were found during DT validation.
-----BEGIN PGP SIGNATURE-----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=CH8u
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.11-rc1
This adds support for the Tegra30-based Ouya game console and enhances a
number of existing device trees. It also fixes a couple of minor issues
that were found during DT validation.
* tag 'tegra-for-5.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (23 commits)
ARM: tegra: Add EMC OPP and ICC properties to Tegra124 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP and ICC properties to Tegra30 EMC and ACTMON device-tree nodes
ARM: tegra: Add EMC OPP properties to Tegra20 device-trees
ARM: tegra: Add nvidia,memory-controller phandle to Tegra20 EMC device-tree
ARM: tegra: Add interconnect properties to Tegra124 device-tree
ARM: tegra: Add interconnect properties to Tegra30 device-tree
ARM: tegra: Add interconnect properties to Tegra20 device-tree
ARM: tegra: acer-a500: Add Embedded Controller
ARM: tegra: Change order of SATA resets for Tegra124
ARM: tegra: Correct EMC registers size in Tegra20 device-tree
ARM: tegra: Properly align clocks for SOCTHERM
ARM: tegra: Hook up edp interrupt on Tegra124 SOCTHERM
ARM: tegra: Add missing hot temperatures to Tegra124 thermal-zones
ARM: tegra: Add missing gpu-throt-level to Tegra124 soctherm
ARM: tegra: Populate OPP table for Tegra20 Ventana
ARM: tegra: nexus7: Use panel-lvds as the only panel compatible
ARM: tegra: nexus7: Rename gpio-hog nodes
ARM: tegra: nexus7: Add power-supply to lvds-encoder node
ARM: tegra: nexus7: Improve CPU passive-cooling threshold
ARM: tegra: nexus7: Correct thermal zone names
...
Link: https://lore.kernel.org/r/20201127144329.124891-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-Fix dmamux reg property (length) on stm32h743.
-Explicitly set DCMI bus type on stm32429i eval board.
MPU part:
-Enable FIFO mode with half-full threshold for DCMI.
-Harmonize EHCI/OHCI nodes.
-Move SDMMC IP version to v2.0 to get features improvements.
-Add LP-timer wakeup support.
-Enable crypto/hash/crc support.
-Explicitly set DCMI bus type on stm32mp157 eval board.
-Add USB type-c controller (STUSB1600) on stm32mp15 DK boards
(It is connected to I2C4).
-Fix dmamux reg property (length) on stm32mp151.
-Optimize USB OTG FIFO sizes on stm32mp151.
-Declare tamp node also as "simple-mfd".
-LXA:
-Document Octavo vendor-prefixes yaml file.
-Document lxa,stm32mp157c-mc1 in STM32 yaml file.
-DH:
-Connect PHY IRQ line on DH SoM.
-Add KS8851 Ethernet support on DHCOM which is mapped to FMC2.
-Document all DH compatible strings in STM32 yaml file.
-Add DHCOM based PicoITX board. This board embedds ethernet port,
USB, CAN LEDS and a custom board-to-board connector.
-----BEGIN PGP SIGNATURE-----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=O+Lk
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.11, round 1
Highlights:
----------
MCU part:
-Fix dmamux reg property (length) on stm32h743.
-Explicitly set DCMI bus type on stm32429i eval board.
MPU part:
-Enable FIFO mode with half-full threshold for DCMI.
-Harmonize EHCI/OHCI nodes.
-Move SDMMC IP version to v2.0 to get features improvements.
-Add LP-timer wakeup support.
-Enable crypto/hash/crc support.
-Explicitly set DCMI bus type on stm32mp157 eval board.
-Add USB type-c controller (STUSB1600) on stm32mp15 DK boards
(It is connected to I2C4).
-Fix dmamux reg property (length) on stm32mp151.
-Optimize USB OTG FIFO sizes on stm32mp151.
-Declare tamp node also as "simple-mfd".
-LXA:
-Document Octavo vendor-prefixes yaml file.
-Document lxa,stm32mp157c-mc1 in STM32 yaml file.
-DH:
-Connect PHY IRQ line on DH SoM.
-Add KS8851 Ethernet support on DHCOM which is mapped to FMC2.
-Document all DH compatible strings in STM32 yaml file.
-Add DHCOM based PicoITX board. This board embedds ethernet port,
USB, CAN LEDS and a custom board-to-board connector.
* tag 'stm32-dt-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: lxa-mc1: add OSD32MP15x to list of compatibles
dt-bindings: arm: stm32: add extra SiP compatible for lxa,stm32mp157c-mc1
dt-bindings: vendor-prefixes: document Octavo Systems oct prefix
ARM: dts: stm32: Add DHCOM based PicoITX board
dt-bindings: arm: stm32: Add compatible strings for DH SoMs and boards
ARM: dts: stm32: support child mfd cells for the stm32mp1 TAMP syscon
dt-bindings: arm: stm32: add simple-mfd compatible for tamp node
ARM: dts: stm32: update stm32mp151 for remote proc synchronization support
ARM: dts: stm32: adjust USB OTG gadget fifo sizes in stm32mp151
ARM: dts: stm32: fix dmamux reg property on stm32h743
ARM: dts: stm32: fix dmamux reg property on stm32mp151
ARM: dts: stm32: fix mdma1 clients channel priority level on stm32mp151
ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
dt-bindings: usb: Add DT bindings for STUSB160x Type-C controller
dt-bindings: connector: add typec-power-opmode property to usb-connector
ARM: dts: stm32: reorder spi4 within stm32mp15-pinctrl
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32429i-eval board
ARM: dts: stm32: set bus-type in DCMI endpoint for stm32mp157c-ev1 board
ARM: dts: stm32: enable CRYP by default on stm32mp15
ARM: dts: stm32: enable CRC1 by default on stm32mp15
...
Link: https://lore.kernel.org/r/873c17a5-28d5-9261-f691-1b917611c932@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Two non-urgent pandaboard updates to get gpio button and bluetooth
working on pandaboard-es
- Updates to follow devicetree binding docs for dwc3 and pwm-leds
- Add initial support for droid bionic based on what we have for droid4
- Add second sha instance for dra7
- Add eQEP nodes for am335x for boneblue
- Fix wrong comments for am335x gpio_31
-----BEGIN PGP SIGNATURE-----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=7jNq
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.11 merge window
- Two non-urgent pandaboard updates to get gpio button and bluetooth
working on pandaboard-es
- Updates to follow devicetree binding docs for dwc3 and pwm-leds
- Add initial support for droid bionic based on what we have for droid4
- Add second sha instance for dra7
- Add eQEP nodes for am335x for boneblue
- Fix wrong comments for am335x gpio_31
* tag 'omap-for-v5.11/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Fix comments for AM335X_PIN_GPMC_WPN pin in GPIO mode
ARM: dts: am335x-boneblue: Enable eQEP
ARM: dts: am33xx: Add nodes for eQEP
ARM: dts: dra7: add second SHA instance
ARM: dts: xt875: add section for kionix kxtf9
ARM: dts: mapphone: separate out xt894 specific things
ARM: dts: omap: Fix schema warnings for pwm-leds
ARM: dts: omap5: Harmonize DWC USB3 DT nodes name
ARM: dts: am437x: Correct DWC USB3 compatible string
ARM: dts: pandaboard es: add bluetooth uart for HCI
ARM: dts: pandaboard: fix pinmux for gpio user button of Pandaboard ES
Link: https://lore.kernel.org/r/pull-1606462656-588116@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Earlier omap4 cpuidle fix was incomplete and needs to use a
configured idle state instead
- Fix am4 cpsw driver compatible to avoid invalid resource error
for the legacy driver
- Two kconfig fixes for genpd support that we added for for v5.10
for proper location of the option and adding missing option
- Fix ti-sysc reset status checking on enabling modules to ignore
quirky modules with reset status only usable when the quirk is
activated during reset. Also fix bogus resetdone warning for
cpsw and modules with no sysst register reset status bit
- Suppress a ti-sysc warning for timers reserved as system timers
- Fix the ordering of clocks for dra7 m_can
-----BEGIN PGP SIGNATURE-----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=KSUM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.10/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for various issues noticed during the -rc cycle:
- Earlier omap4 cpuidle fix was incomplete and needs to use a
configured idle state instead
- Fix am4 cpsw driver compatible to avoid invalid resource error
for the legacy driver
- Two kconfig fixes for genpd support that we added for for v5.10
for proper location of the option and adding missing option
- Fix ti-sysc reset status checking on enabling modules to ignore
quirky modules with reset status only usable when the quirk is
activated during reset. Also fix bogus resetdone warning for
cpsw and modules with no sysst register reset status bit
- Suppress a ti-sysc warning for timers reserved as system timers
- Fix the ordering of clocks for dra7 m_can
* tag 'omap-for-v5.10/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra76x: m_can: fix order of clocks
bus: ti-sysc: suppress err msg for timers used as clockevent/source
ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606460270-864284@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Cleanups of the hisilicon DTS to align with the dtschema including
serial, usb, amba-bus, memory, mmc, spi and syscon. All of them do not
have any functional effect except passing dtschema checks or dtc W=2
builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a9Ci
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm32-dt-for-5.11' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 DT updates for 5.11
- Cleanups of the hisilicon DTS to align with the dtschema including
serial, usb, amba-bus, memory, mmc, spi and syscon. All of them do not
have any functional effect except passing dtschema checks or dtc W=2
builds.
* tag 'hisi-arm32-dt-for-5.11' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: fix errors detected by syscon.yaml
ARM: dts: hisilicon: fix errors detected by spi-pl022.yaml
ARM: dts: hisilicon: fix errors detected by synopsys-dw-mshc.yaml
ARM: dts: hisilicon: fix errors detected by root-node.yaml
ARM: dts: hisilicon: fix errors detected by simple-bus.yaml
ARM: dts: hisilicon: fix errors detected by usb yaml
ARM: dts: hisilicon: fix errors detected by pl011.yaml
ARM: dts: hisilicon: fix errors detected by snps-dw-apb-uart.yaml
Link: https://lore.kernel.org/r/5FBDC347.4050102@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add EMC OPP DVFS/DFS tables and interconnect paths that will be used for
dynamic memory bandwidth scaling based on memory utilization statistics.
Update board device-trees by removing unsupported EMC OPPs.
Note that ACTMON watches all memory interconnect paths, but we use a
single CPU-READ interconnect path for driving memory bandwidth, for
simplicity.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add EMC OPP tables and interconnect paths that will be used for
dynamic memory bandwidth scaling based on memory utilization statistics.
Update board device-trees by removing unsupported EMC OPPs.
Note that ACTMON watches all memory interconnect paths, but we use a
single CPU-READ interconnect path for driving memory bandwidth, for
simplicity.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add nvidia,memory-controller to the Tegra20 External Memory Controller
node. This allows to perform a direct lookup of the Memory Controller
instead of walking up the whole tree. This puts Tegra20 device-tree on
par with Tegra30+.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add interconnect properties to the Memory Controller, External Memory
Controller and the Display Controller nodes in order to describe hardware
interconnection.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds device-tree node for the Embedded Controller which is
found on the Picasso board. The Embedded Controller itself is ENE KB930,
it provides functions like battery-gauge/LED/GPIO/etc and it uses firmware
that is specifically customized for the Acer A500 device.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra AHCI dt-binding doc is converted from text based to yaml based.
dtbs_check valdiation strictly follows reset-names order specified
in yaml dt-binding.
Tegra124 thru Tegra210 has 3 resets sata, sata-oob and sata-cold.
Tegra186 has 2 resets sata and sata-cold.
This patch changes order of SATA resets to maintain proper resets
order for commonly available resets across Tegra124 thru Tegra186
for dtbs_check to pass.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the size of Tegra20 EMC registers, which should be twice bigger.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For some reason this was never hooked up. Do it now so that over-current
interrupts can be logged.
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to dmesg, thermal-zones for mem and cpu are missing hot
temperatures properties.
throttrip: pll: missing hot temperature
...
throttrip: mem: missing hot temperature
...
Adding them will clear the messages.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Jetson TK1 the following message can be seen:
tegra_soctherm 700e2000.thermal-sensor: throttle-cfg: heavy: no throt prop or invalid prop
This patch will fix the invalid prop issue according to the binding.
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver
(Tegra30 supported now)") update the Tegra20 CPUFREQ driver to use the
generic CPUFREQ device-tree driver. Since this change CPUFREQ support
on the Tegra20 Ventana platform has been broken because the necessary
device-tree nodes with the operating point information are not populated
for this platform. Fix this by updating device-tree for Venata to
include the operating point informration for Tegra20.
Fixes: 9ce2746304 ("cpufreq: tegra20: Use generic cpufreq-dt driver (Tegra30 supported now)")
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depending on a driver probe order, panel-simple driver may probe first,
which results in this error:
panel-simple display-panel: Reject override mode: panel has a fixed mode
We don't want to use panel-simple anyways because customized timings are
preferred for Nexus 7, hence remove the panel-simple compatibles from the
panel node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devicetree schema now requires gpio-hog nodes to have a certain naming
pattern, like a -hog suffix. This patch fixes dtbs_check warnings about
the names.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The lvds-encoder binding now supports power-supply property, let's specify
it in the device-tree for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current CPU thermal limit is a bit inappropriate for Nexus 7 once
device is getting used on a daily bases. For example, currently it's may
be impossible to watch a hardware accelerated 720p video without hitting
a severe CPU throttling, which ruins user experience. This patch improves
the thermal throttling thresholds.
In my experience setting CPU thermal threshold to 57C provides the most
reasonable result, where device is a bit warm under constant load and
not getting overly hot, in the same time performance is okay. Let's bump
the passive-cooling threshold from 50C to 57C and also lower the thermal
hysteresis to 0.2C in order to make throttling more reactive.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename thermal zones in order fix dt_binding_check warning telling that
names do not match the expected pattern.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The lvds-encoder binding now supports power-supply property, let's specify
it in the device-tree for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename thermal zones in order fix dt_binding_check warning telling that
names do not match the expected pattern.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Ouya was the sole device produced by Ouya Inc in 2013.
It was a game console originally running Android 5 on top of Linux 3.1.10.
This patch adds the device tree supporting the Ouya.
It has been tested on the original variant with Samsung ram.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG Nexus 5 uses a maxim17048 fuelgauge. The maxim,rcomp value is
taken from downstream dt. Temperature-based compensation is not yet
supported in the mainline driver, but the readings seem fine nevertheless.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@protonmail.com>
Link: https://lore.kernel.org/r/20201126141144.1763779-2-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy S5 uses a maxim17048 fuelgauge. The maxim,rcomp value
is taken from downstream kernel. Model data and temperature-based
compensation are not yet supported in the mainline driver, but the
readings seem fine nevertheless.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20201126141144.1763779-1-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Earlier commit modified the binding, so the SiP is to be specified
as well. Adjust the device tree accordingly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The stm32mp1 TAMP peripheral has 32 backup registers that survive
a warm reset. This makes them suitable for storing a reboot
mode, which the vendor's kernel tree is already doing[0].
The actual syscon-reboot-mode child node can be added by a board.dts or
fixed up by the bootloader. For the child node to be probed, the
compatible needs to include simple-mfd. The binding now specifies this,
so have the SoC dtsi adhere to it.
[0]: https://github.com/STMicroelectronics/linux/commit/2e9bfc29dd
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Two backup registers are used to store the Cortex-M4 state and the resource
table address.
Declare the tamp node and add associated properties in m4_rproc node
to allow Linux to attach to a firmware loaded by the first boot stages.
Associated driver implementation is available in commit 9276536f45
("remoteproc: stm32: Parse syscon that will manage M4 synchronisation").
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Defaut use case on stm32mp151 USB OTG is ethernet gadget, using EP1 bulk
endpoint (MPS=512 bytes) and EP2 interrupt endpoint (MPS=16 bytes).
This patch optimizes USB OTG FIFO sizes accordingly.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reg property length should cover all DMAMUX_CxCR registers.
DMAMUX_CxCR Address offset: 0x000 + 0x04 * x (x = 0 to 15), so latest
offset is at 0x3c, so length should be 0x40.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reg property length should cover all DMAMUX_CxCR registers.
DMAMUX_CxCR Address offset: 0x000 + 0x04 * x (x = 0 to 15), so latest
offset is at 0x3c, so length should be 0x40.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for STUSB1600 USB Type-C port controller, used on
I2C4 on stm32mp15xx-dkx.
The default configuration on this board, on Type-C connector, is:
- Dual Power Role (DRP), so set power-role to "dual";
- Vbus limited to 500mA, so set typec-power-opmode to "default" (it means
500mA in USB 2.0).
typec-power-opmode is used to reconfigure the STUSB1600 advertising of
current capability when its NVM is not in line with the board layout.
On stm32mp15xx-dkx, Vbus power source of STUSB1600 is 5V_VIN. So power
operation mode depends on the power supply used. To avoid any power
issues, it is better to limit Vbus to 500mA on this board.
ALERT# is the interrupt pin of STUSB1600. It needs an external pull-up, and
signal is active low.
USB OTG controller ID and Vbus signals are not connected on stm32mp15xx-dkx
boards, so disconnection are not detected.
Without DWC2 usb-role-switch:
- if you unplug the USB cable from the Type-C port, you have to manually
disconnect the USB gadget:
echo disconnect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
- Then you can plug the USB cable again in the Type-C port, and manually
reconnect the USB gadget:
echo connect > /sys/devices/platform/soc/49000000.usb-otg/udc/49000000.usb-otg/soft_connect
With DWC2 usb-role-switch, USB gadget is dynamically disconnected or connected.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4 at the right alphabetical place within stm32mp15-pinctrl
Fixes: 4fe663890a ("ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
LP timer can be used to wakeup from stop mode on stm32mp151.
Add wakeup-source properties to all LP timer instances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update the IP version to v2.0, which supports linked lists in internal DMA,
and is present in STM32MP1 SoCs.
The mmci driver supports the v2.0 periph id since 7a2a98be67 ("mmc: mmci:
Add support for sdmmc variant revision 2.0"), so it's now Ok to add it into
the SoC device tree to benefit from the improved DMA support.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adding Z-turn board V5 to resolve the change between:
"Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035
"Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031
Changes v1 -> v2: Instead of using new board, the v2 using a common devicetree
for z-turn boards (zynq-zturn-common.dtsi) and for each board a specific DT
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Link: https://lore.kernel.org/r/20201126070516.85882-1-agriveaux@deutnet.info
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.
phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d63 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").
Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.
Fixes: 061035d456 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org
The DT binding for system controller is not allowed to contain only the
compatible string "syscon", the Hisilicon peripheral subsystem controller
should add compatible string "hisilicon,peri-subctrl". Otherwise, the
error "compatible: ['syscon'] is too short" will be reported.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change clock-names to "sspclk", "apb_pclk". Both of them use the same
clock.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Look at the clock-names schema defined in synopsys-dw-mshc.yaml:
clock-names:
items:
- const: biu
- const: ciu
The "biu" needs to be placed before the "ciu".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Make the memory node name match the regex "^memory(@[0-9a-f]+)?$" which
is described in memory.yaml. Otherwise, it will be treated as root node,
and misreported by root-node.yaml.
Errors misreported by root-node.yaml:
/: memory: False schema does not allow {'device_type': ['memory'], 'reg':
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change bus node name from "amba" to "amba-bus" to match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change node name to match '^usb(@.*)?'
These errors are detected by generic-ehci.yaml and generic-ohci.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change node name to match '^serial(@[0-9a-f,]+)*$'
2. Change clock-names to "uartclk", "apb_pclk". Both of them use the same
clock.
3. Change pinctrl-names to "default", "sleep".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change node name to match '^serial(@[0-9a-f,]+)*$'
2. Change clock-names to "baudclk", "apb_pclk". Both of them use the same
clock.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: b7c2b61570 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-4-cristian.birsan@microchip.com
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-3-cristian.birsan@microchip.com
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-2-cristian.birsan@microchip.com
- Rename the DSI controllers to match the preferred
schema.
- Pull down the SDI2 feedback clock on the Skomer.
- Add proper supplies to the MaxToch touchscreen on
the Golden.
-----BEGIN PGP SIGNATURE-----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=TF1x
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.11 kernels:
- Rename the DSI controllers to match the preferred
schema.
- Pull down the SDI2 feedback clock on the Skomer.
- Add proper supplies to the MaxToch touchscreen on
the Golden.
* tag 'ux500-dts-for-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500-golden: Add proper supplies to touchscreen
ARM: dts: ux500: skomer: Pull down SDI2 FBCLK
ARM: dts: ux500: Rename DSI controller nodes
Link: https://lore.kernel.org/r/CACRpkdY_M4xj++QhRPqX6N3x9YmFNJkz70DnvBj7Ai-dOtCJSQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Nuvoton NPCM730 SoC device tree.
The Nuvoton NPCN730 SoC is a part of the
Nuvoton NPCM7xx SoCs family.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Benjamin Fair <benjaminfair@google.com>
Link: https://lore.kernel.org/r/20201119080002.100342-1-tmaimon77@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Many cleanups of DTS and alignments to dtschema. Most of them do not
have any functional effect except passing dtschema checks or dtc W=2
builds.
2. Fix USB 3.0 ports on Odroid XU board: wrong roles assigned to two
ports, missing supply to the USB over-current and VBUS control pins
and finally missing pin configuration for these pins.
3. Switch Exynos5422 DMC driver to monitoring/polling mode, instead of
using interrupts.
4. Correct the usage of "opp-shared" properties which lead to disabling
the bus frequency and voltage scaling.
5. Enable Bluetooth on few Exynos4210 and Exynos4412 boards.
6. Enable dual-role USB on Odroid U3+ board.
7. Add Ethernet description in multiple Odroid DTS allowing also easy
MAC address filling by bootloader.
8. Add Ethernet to Artik 5 (Exynos3250) board.
9. Add interconnect properties to Exynos4412 to fix old Mixer issues.
-----BEGIN PGP SIGNATURE-----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=TybJ
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.11
1. Many cleanups of DTS and alignments to dtschema. Most of them do not
have any functional effect except passing dtschema checks or dtc W=2
builds.
2. Fix USB 3.0 ports on Odroid XU board: wrong roles assigned to two
ports, missing supply to the USB over-current and VBUS control pins
and finally missing pin configuration for these pins.
3. Switch Exynos5422 DMC driver to monitoring/polling mode, instead of
using interrupts.
4. Correct the usage of "opp-shared" properties which lead to disabling
the bus frequency and voltage scaling.
5. Enable Bluetooth on few Exynos4210 and Exynos4412 boards.
6. Enable dual-role USB on Odroid U3+ board.
7. Add Ethernet description in multiple Odroid DTS allowing also easy
MAC address filling by bootloader.
8. Add Ethernet to Artik 5 (Exynos3250) board.
9. Add interconnect properties to Exynos4412 to fix old Mixer issues.
* tag 'samsung-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (36 commits)
ARM: dts: exynos: use hyphens in MFC reserved memory node names
ARM: dts: exynos: use hyphens in Exynos5 node names
ARM: dts: exynos: use generic name for max77693 motor in Midas
ARM: dts: exynos: use hyphens in Exynos4 node names
ARM: dts: exynos: use hyphens in Exynos3250 node names
ARM: dts: exynos: Add interconnects to Exynos4412 mixer
ARM: dts: exynos: Add interconnect properties to Exynos4412 bus nodes
ARM: dts: exynos: Add Ethernet to Artik 5 board
ARM: dts: exynos: Add a placeholder for a MAC address
ARM: dts: exynos: Add Ethernet interface description for Odroid X/X2
ARM: dts: exynos: Add Ethernet interface description for Odroid U3
ARM: dts: exynos: Add Ethernet interface description for Odroid XU
ARM: dts: exynos: Add Ethernet interface description for Odroid XU3 Lite
ARM: dts: exynos: Enable DWC2 dual-role support on OdroidU3+ boards
ARM: dts: s5pv210: adjust node names to DT spec
ARM: dts: exynos: adjust node names to DT spec in Exynos542x boards
ARM: dts: exynos: adjust node names to DT spec in Odroid XU
ARM: dts: exynos: adjust node names to DT spec in Exynos5250 boards
ARM: dts: exynos: remove redundant status=okay in Exynos4412 boards
ARM: dts: exynos: adjust node names to DT spec in Exynos4412 boards
...
Link: https://lore.kernel.org/r/20201113162211.10020-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Touch screen and OV5640 camera support for the iWave RainboW Qseven
board (G21D), and its camera expansion board,
- Support for the AISTARVISION MIPI Adapter V2.1 board connected to
HiHope RZ/G2 boards,
- SPI (MSIOF) support for the R-Car M3-W+ SoC,
- Digital Radio Interface (DRIF) support for the R-Car M3-N SoC,
- Initial support for the R-Car M3-W+ ULCB/Kingfisher board combo,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX66VTQAKCRCKwlD9ZEnx
cFhnAP9W9Jp5o/gp9JQ+Y2Js3xMDD9JngTYRQ+9x4qu2HTf0AAEAjfSzb0T2ub/x
HaW5LisNk1LZNp09+9ugw/nNZxp45AQ=
=QdJ8
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.11
- Touch screen and OV5640 camera support for the iWave RainboW Qseven
board (G21D), and its camera expansion board,
- Support for the AISTARVISION MIPI Adapter V2.1 board connected to
HiHope RZ/G2 boards,
- SPI (MSIOF) support for the R-Car M3-W+ SoC,
- Digital Radio Interface (DRIF) support for the R-Car M3-N SoC,
- Initial support for the R-Car M3-W+ ULCB/Kingfisher board combo,
- Minor fixes and improvements.
* tag 'renesas-arm-dt-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: hihope-rev4: Add a comment explaining switch SW2404
arm64: dts: renesas: r8a77961: ulcb-kf: Initial device tree
arm64: dts: renesas: r8a77961: Add CAN{0,1} placeholder nodes
arm64: dts: renesas: beacon-renesom-baseboard: Move connector node out of hd3ss3220 device
arm64: dts: renesas: cat874: Move connector node out of hd3ss3220 device
arm64: dts: renesas: rzg2: Convert EtherAVB to explicit delay handling
arm64: dts: renesas: rcar-gen3: Convert EtherAVB to explicit delay handling
arm64: dts: renesas: r8a77965: Add DRIF support
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2N
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2M
arm64: dts: renesas: Add support for MIPI Adapter V2.1 connected to HiHope RZ/G2H
arm64: dts: renesas: aistarvision-mipi-adapter-2.1: Add parent macro for each sensor
arm64: dts: renesas: cat875: Remove rxc-skew-ps from ethernet-phy node
arm64: dts: renesas: hihope-rzg2-ex: Drop rxc-skew-ps from ethernet-phy node
ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Enable VIN instances
arm64: dts: renesas: r8a77961: Add MSIOF nodes
arm64: dts: renesas: Align GPIO hog names with dtschema
ARM: dts: r8a7742-iwg21d-q7: Add LCD support
Link: https://lore.kernel.org/r/20201113150854.3923885-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This sets up the Atmel maXTouch touchscreen to use proper
VDDA and VDD supplies as now supported by bindings and
driver.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Nick Dyer <nick@shmanahar.org>
Link: https://lore.kernel.org/r/20201120124212.1086063-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reset GPIO logic of the Atmel maxtouch driver was changed to be
active low at around the same time P4 Note device tree was accepted into
the kernel. Adjust the configuration so that the touchscreen is in a
usable state.
Signed-off-by: Martin Jücker <martin.juecker@gmail.com>
Link: https://lore.kernel.org/r/20201120160053.18942-1-martin.juecker@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The board is using McASP2 for both analog (tlv320aic3106) and
HDMI (SiI9022) audio.
12.288MHz oscillator provides the MCLK for both aic3106 and SiI9022.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Provide an empty 'ports' container node with the correct #address-cells
and #size-cells properties. This silences the following warning:
arch/arm/boot/dts/bcm958522er.dt.yaml:
ethernet-switch@36000: 'oneOf' conditional failed, one must be fixed:
'ports' is a required property
'ethernet-ports' is a required property
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Provide a valid compatible string for the Ethernet switch node based on
the board including the switch. This allows us to have sane defaults and
silences the following warnings:
arch/arm/boot/dts/bcm958522er.dt.yaml:
ethernet-switch@36000: compatible: 'oneOf' conditional failed,
one
must be fixed:
['brcm,bcm5301x-srab'] is too short
'brcm,bcm5325' was expected
'brcm,bcm53115' was expected
'brcm,bcm53125' was expected
'brcm,bcm53128' was expected
'brcm,bcm5365' was expected
'brcm,bcm5395' was expected
'brcm,bcm5389' was expected
'brcm,bcm5397' was expected
'brcm,bcm5398' was expected
'brcm,bcm11360-srab' was expected
'brcm,bcm5301x-srab' is not one of ['brcm,bcm53010-srab',
'brcm,bcm53011-srab', 'brcm,bcm53012-srab', 'brcm,bcm53018-srab',
'brcm,bcm53019-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm11404-srab',
'brcm,bcm11407-srab', 'brcm,bcm11409-srab', 'brcm,bcm58310-srab',
'brcm,bcm58311-srab', 'brcm,bcm58313-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm58522-srab',
'brcm,bcm58523-srab', 'brcm,bcm58525-srab', 'brcm,bcm58622-srab',
'brcm,bcm58623-srab', 'brcm,bcm58625-srab', 'brcm,bcm88312-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm3384-switch',
'brcm,bcm6328-switch', 'brcm,bcm6368-switch']
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The register name should be "sgmii_config", not "sgmii", this is not a
functional change since no code is currently looking for that register
by name (or at all).
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the switch unit name from srab to ethernet-switch, allowing us
to fix warnings such as:
CHECK arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml
arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml:
srab@18007000: $nodename:0: 'srab@18007000' does not match
'^(ethernet-)?switch(@.*)?$'
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Provide an empty 'ports' container node with the correct #address-cells
and #size-cells properties. This silences the following warning:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml:
ethernet-switch@18007000: 'oneOf' conditional failed, one must be fixed:
'ports' is a required property
'ethernet-ports' is a required property
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Provide a default compatible string which is based on the 53011 SRAB
compatible by default. The 4709 and 47094 default to the 53012 SRAB
compatible.
This allows us to have sane defaults and silences the following
warnings:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dt.yaml:
ethernet-switch@18007000: compatible: 'oneOf' conditional failed, one
must be fixed:
['brcm,bcm5301x-srab'] is too short
'brcm,bcm5325' was expected
'brcm,bcm53115' was expected
'brcm,bcm53125' was expected
'brcm,bcm53128' was expected
'brcm,bcm5365' was expected
'brcm,bcm5395' was expected
'brcm,bcm5389' was expected
'brcm,bcm5397' was expected
'brcm,bcm5398' was expected
'brcm,bcm11360-srab' was expected
'brcm,bcm5301x-srab' is not one of ['brcm,bcm53010-srab',
'brcm,bcm53011-srab', 'brcm,bcm53012-srab', 'brcm,bcm53018-srab',
'brcm,bcm53019-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm11404-srab',
'brcm,bcm11407-srab', 'brcm,bcm11409-srab', 'brcm,bcm58310-srab',
'brcm,bcm58311-srab', 'brcm,bcm58313-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm58522-srab',
'brcm,bcm58523-srab', 'brcm,bcm58525-srab', 'brcm,bcm58622-srab',
'brcm,bcm58623-srab', 'brcm,bcm58625-srab', 'brcm,bcm88312-srab']
'brcm,bcm5301x-srab' is not one of ['brcm,bcm3384-switch',
'brcm,bcm6328-switch', 'brcm,bcm6368-switch']
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the switch unit name from srab to ethernet-switch, allowing us to
fix warnings such as:
CHECK arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml
arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml:
srab@18007000: $nodename:0: 'srab@18007000' does not match
'^(ethernet-)?switch(@.*)?$'
From schema:
Documentation/devicetree/bindings/net/dsa/b53.yaml
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently the GIC node in V3s DTSI follows some old DT examples, and
being broken. This leads a warning at boot.
Fix this.
Fixes: f989086ccb ("ARM: dts: sunxi: add dtsi file for V3s SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201120050851.4123759-1-icenowy@aosc.io
The previous version of the dwc2 overlay set the RX FIFO size to
256 4-byte words. This is not enough for 1024 bytes of the largest
isochronous high speed packet allowed, because it doesn't take into
account extra space needed by dwc2.
RX FIFO's size is calculated based on the following (in 4byte words):
- 13 locations for SETUP packets
5*n + 8 for Slave and Buffer DMA mode where n is number of control
endpoints which is 1 on the bcm283x core
- 1 location for Global OUT NAK
- 2 * 257 locations for status information and the received packet.
Typically two spaces are recommended so that when the previous packet
is being transferred to AHB, the USB can receive the subsequent
packet.
- 10 * 1 location for transfer complete status for last packet of each
endpoint. The bcm283x core has 5 IN and 5 OUT EPs
- 10 * 1 additional location for EPDisable status for each endpoint
- 5 * 2 additional locations are recommended for each OUT endpoint
Total is 558 locations.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/e9e7d070-593c-122f-3a5c-2435bb147ab2@ivitera.com/
The RPi4 WiFi chip and HDMI outputs have some frequency overlap with
crosstalk around 2.4GHz. Let's mark it as such so we can use some evasive
maneuvers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201029134018.1948636-3-maxime@cerno.tech
Add remaining PRM instances for the omap5 SoC. Additionally enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add remaining PRM instances for the dra7 SoC. Additionally enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add remaining PRM instances for the omap4 SoC. Additionally enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MAC0 was not functional in the AST2600A0 SoC. This has been resolved
with the A1, so allow use of this port on EVBs with the A1 and
subsequent revisions.
A0 EVBs will still boot with this change, but the first Ethernet device
will not be functional.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Some of the FSI-attached SPI controllers can't use the loop command
due to security requirements. Indicate this in the devicetree with
the restricted compatible string.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20201102194713.14812-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
According to the bosch,m_can.yaml bindings the first clock shall be the "hclk",
while the second clock "cclk".
This patch fixes the order accordingly.
Fixes: 0adbe832f2 ("ARM: dts: dra76x: Add MCAN node")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree for the Kudo BMC. Kudo is an Ampere (Altra)
server platform manufactured by Fii and is based on a Nuvoton
NPCM730 SoC.
Signed-off-by: Mustatfa Shehabi <Mustafa.Shehabi@fii-na.com>
Signed-off-by: Mohaimen alsmarai <Mohaimen.alsamarai@fii-na.com>
Signed-off-by: Lancelot Kao <lancelot.kao@fii-usa.com>
Reviewed-by: Vivekanand Veeracholan <vveerach@google.com>
Reviewed-by: Benjamin Fair <benjaminfair@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201116232127.7066-1-lancelot.kao@fii-usa.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Quanta GSJ BMC uses the Nuvoton NPCM730 SoC.
Included features:
1. Image partitions
2. PWM fan controller
3. USB device
4. Serial port
5. FIU
6. LEDs and GPIOs
Signed-off-by: Fran Hsu <Fran.Hsu@quantatw.com>
Reviewed-by: Benjamin Fair <benjaminfair@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add pinctrl definition for the Quanta GSJ BMC machine.
Signed-off-by: Fran Hsu <Fran.Hsu@quantatw.com>
Reviewed-by: Benjamin Fair <benjaminfair@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Nuvoton NPCN730 SoC is a part of the Nuvoton NPCM7xx SoCs family.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reserve a 1.5MiB region of memory to record kmsg dumps, console and
userspace message state into 16kiB ring-buffer slots. The sizing allows
for up to 16 dumps to be captured and read out.
Set max-reason to KMSG_DUMP_EMERG to capture bad-path reboots.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201022014731.2035438-7-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reserve a 1.5MiB region of memory to record kmsg dumps, console and
userspace message state into 16kiB ring-buffer slots. The sizing allows
for up to 16 dumps to be captured and read out.
Set max-reason to KMSG_DUMP_EMERG to capture bad-path reboots.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201022014731.2035438-6-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
The mismatch lead to a miscalculation of regions in another patch, and
shouldn't be mismatched anyway, so make them consistent.
Fixes: 575640201e ("ARM: dts: aspeed: tacoma: Use 64MB for firmware memory")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201022014731.2035438-2-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This property is only useful if a node has children as it allows them
to then use io-channel properties in the parent. Here there are no
children.
This is harmless, but we are planning to shortly drop this property
as it is rarely used correctly and there is little reason it would
ever be needed as we can just provide the io-channels property to
any child nodes that need it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-8-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This property is relevant to consumers of io-channels. Here it is
used by a provider.
dt-schema will now report and error as this property must be in the
same node as io-channels and it is not here.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-6-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This property is only relevant to consumers of io-channels, not providers.
All these dtsi files have it alongside #io-channel-cells which indicates
they are providers of io-channels, not consumers.
Note that dt-schema will now flag this up due to a dependency between
this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-5-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a device-tree for the Rainier 4U system. Change the model name
on the existing Rainier device-tree to 2U, and remove the two
extra power supplies that are only present on the 4U system. Also
add labels to the fan nodes for use in the 4U device-tree.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201028185647.14565-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add bindings for the KS8851 ethernet present on the STM32MP1 DHCOM SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FMC EBI bus, this is used on DHCOM SoM
for the second ethernet and on the PDK2 devkit for SRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On the production DHCOM STM32MP15xx SoM, the PHY IRQ line is connected
to the PI11 pin. Describe it in the DT as well, so the PHY IRQ can be
used e.g. to detect cable insertion and removal.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Modify NPCM7xx device tree timer register size
from 0x50 to 0x1C to control only the timer registers
and not other hw modules.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200929131807.15378-3-tmaimon77@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Modify NPCM7xx device tree clock parameter to clock constants that
define at include/dt-bindings/clock/nuvoton,npcm7xx-clock.h file.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200929131807.15378-2-tmaimon77@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The P4 Note family contains a couple of variants of the Galaxy Note 10.1
tablet with mainly different modems. The GT-N8010/GT-N8013 is the WiFi
only version.
Signed-off-by: Martin Jücker <martin.juecker@gmail.com>
Link: https://lore.kernel.org/r/20201113212525.13455-3-martin.juecker@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl+yQKUUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7dVgf1GkIY1GbPIvkMZB3CiQZ0e40vUmWx
CW70bOrGAcSSgYvL7tBqb7I5U5+01m4whtsal6jK/TTZ4w2PAItZpgi3ZiXooyO9
3qGHr7IgcuCWzQ2Bjg+YGR1esGTi2+KKggCWog0R8ipy5gUCvIcuLNyBtxjlkbKt
1kkxEDOdmeXPAUQboEdRPZF4m6J/q8g/QgY8GeLsPeContEvAXBMMdNgIRHmWZ6H
iu3H33ogseBkm5RvSfdjmTKPnz9/5hF94yEpGgTkWrawq2bMXwt7loBsQl/TyUVg
d01gZl5yOxjtMXcnJ5bW+6SOpPbjUBFczg1+C2u2tDpeES5DjjYLS0fb
=zT+s
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to AM335x datasheet pin AM335X_PIN_GPMC_WPN in MODE7 works as
GPIO0[31].
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the Enhanced Quadrature Encoder Pulse (eQEP) module for
connectors E1, E2 and E3 on BeagleBone Blue.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds new nodes for the Texas Instruments Enhanced Quadrature
Encoder Pulse (eQEP) module in the PWM subsystem on AM33XX.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC has two SHA instances, add the missing second one under the
main dts file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation for probing l3 with simple-pm-bus and genpd, we must move
l3 noc to a separate node to prevent omap_l3_noc.c driver from claiming
the whole l3 instance before simple-pm-bus has a chance to probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Note that we need to use "ti,no-idle" here.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Note that we no longer need ti,no-reset-on-init as the rstctrl resets
are properly handled by the reset driver and claimed by the RTC driver.
And we need to squash together the module ranges for driver compability.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For genpd we need the RTC powerdomain configured.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
To drop the legacy platform data for am3 control module, we need
to configure the missing functional clock and tag the module to
not idle as platform data also had it configured with
HWMOD_INIT_NO_IDLE.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now manage clocksource and clockevent clocks directly with
timer-ti-dm-systimer. In order to use genpd with prm_omap,
GENPD_FLAG_PM_CLK and simple-pm-bus, we need to keep the system
timer related interconnect clocks enabled until clocksource suspend
is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add remaining PRM instances for the am43xx SoC. Additionally enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Note that we need to use "ti,no-idle" here.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Note that we no longer need ti,no-reset-on-init as the rstctrl resets
are properly handled by the reset driver and claimed by the RTC driver.
And we need to squash together the module ranges for driver compability.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For genpd we need the RTC powerdomain configured.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
To drop the legacy platform data for am3 control module, we need
to configure the missing functional clock and tag the module to
not idle as platform data also had it configured with
HWMOD_INIT_NO_IDLE.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now manage clocksource and clockevent clocks directly with
timer-ti-dm-systimer. In order to use genpd with prm_omap,
GENPD_FLAG_PM_CLK and simple-pm-bus, we need to keep the system
timer related interconnect clocks enabled until clocksource suspend
is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add remaining PRM instances for the am33xx SoC. Additionally, enable the
genpd support for them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: fixed a typo for #power-domain-cells]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Kobo Aura has an eKTF2132 touchscreen controller.
Although the vendor kernel toggles a reset pin (GPIO5-12) during the
startup sequence, the touchscreen works without it.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX SoCs nand node name from "flexcan" to "can" to be compliant with
yaml schema, it requires the nodename to be "can". This fixes the following
error found by dtbs_check:
arch/arm/boot/dts/imx6dl-apf6dev.dt.yaml: flexcan@2090000: $nodename:0: 'flexcan@2090000' does not match '^can(@.*)?$'
From schema: Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are four flavors of TechNexion PICO-IMX6 boards. They have their
own DTSes, even though in Dwarf, Nymph and Pi are exactly the same.
They also have their own bindings so adjust the compatibles to match the
bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tioga Pass reference design includes Intel I210 Ethernet controller
connected to the BMC with NC/SI.
MAC readout is not supported.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Vijay Khemka <vijaykhemkalinux@gmail.com>
Tested-by: Vijay Khemka <vijaykhemkalinux@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches) use
the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201110072446.8218-1-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Update "data0" partition's size from 8MB to 4MB to fix "partition data0
extends beyond the end of device" warning at bootup time.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201110072159.7941-1-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This property applies to consumers of io-channels. In this case we
have a provider so the property is not used.
Recent changes to dt-schema result int his being reported as an error
as a dependency is enforced between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This device has a functional USB 3 port so PHY is required.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This reverts commit eaf2d2f689.
The commit eaf2d2f689 ("ARM: dts: exynos: add input clock to CMU in
Exynos4412 Odroid") breaks probing of usb3503 USB hub on Odroid U3.
It changes the order of clock drivers probe: the clkout (Exynos PMU)
driver is probed before the main clk-exynos4 driver. The clkout driver
on Exynos4412 depends on clk-exynos4 but it does not support deferred
probe, therefore this dependency and changed probe order causes probe
failure.
The usb3503 USB hub on Odroid U3 on the other hand requires clkout
clock. This can be seen in logs:
[ 5.007442] usb3503 0-0008: unable to request refclk (-517)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200921174818.15525-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl+fStkUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6UJggAgRnnMfVrvpZqZSYlj3CirW4jOeeo
oxkh8L3XcvOh5f1StI15879a93E5fq4CLoVUda5vdWJLO8Q0pl5VGJsTfzNpekAY
mswq8ratwKragLOX8FhSr/YLICoF6qLmIDn0EtAuOwLrcii4i5pgLqj0t/5MQm9U
NyAbb/nYZWWm2S8szOaB6+OfYbXxV9YHMFkFL9ZetppS/ezYq3UNq2i//aTBB33z
wFhqt8+scuT3cikdtFumb+vbMMYtUcGfJxkgLEoQz3P53WL1w0jzJXQ47egWI6/d
16zEUavTk9WUKcWS8knY8KKToVaU6GKIr+JLUOczWOhMPUtxANsLvLOmjQ==
=M32F
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, 3rd round:
- A series from Krzysztof Kozlowski to fix missing PMIC's interrupt
line pull-up for i.MX8MM and i.MX8MN boards.
- Set Bluetooth chip max-speed to 4000000 on imx8mm-beacon-som board
to fix the choppy Bluetooth audio sound.
- Remove non-existent OTG2, usbphynop2, and the usbmisc2 from i.MX8MN
device tree.
- Fix the endianness setting of RCPM node on Layerscape SoCs.
- Add the missing dma-coherent property for qoriq-fman device to improve
the performance.
- Fix the Ethernet PHY address on imx6q-prti6q board.
* tag 'imx-fixes-5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-prti6q: fix PHY address
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-ddr4-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mn-var-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-evk: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-beacon-som: fix missing PMIC's interrupt line pull-up
arm64: dts: imx8mm-var-som: fix missing PMIC's interrupt line pull-up
Link: https://lore.kernel.org/r/20201030151821.GA28266@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add initial version of device tree for Facebook Galaxy100 (AST2400) BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201111232330.30843-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify the Wedge100 device tree by using the common dtsi.
In addition this enables the second firmware flash, and turns on the
"i2c-mux-idle-disconnect" flag for I2C switch 7-0070.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201111232330.30843-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify the Wedge40 device tree by using the common dtsi.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201111232330.30843-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This common descirption is included by all Facebook AST2400 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201111232330.30843-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Clocks and thermal blocks are part of the CRU ("Clock and Reset Unit" or
"Central Resource Unit").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Now that we have a pin controller, use that instead of manuplating the
mdio/mdc pins directly. i.e. we no longer require the mdio-mii-mux
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM47094 version of pinmux uses different compatible and supports MDIO
pinmux pins. Hence, use the correct compatible string and defines the
MDIO pins group.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This router has dual paritions to store trx firmware image and
dual partitions for nvram. The second one in each of these cases acts
as a backup store.
When tested with OpenWrt, the default partition parser causes two issues:
1. It labels both nvram partitions as nvram. In factory, second one is
labeled devinfo.
2. It parses second trx image and tries to create second 'linux' partition
and fails with - cannot create duplicate 'linux' partition
The following patch works around both of these issues.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In accordance with the Generic xHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-xhci"-compatible nodes are
correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add ports 5 and 7 which are connected to gmac cores 1 & 2.
These will be disabled for now.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add GPIO line names for AMD EthanolX customer reference board.
It populates AST2500 GPIO lines (A0-A7 to AC0-AC7) with AMD EthanolX
designated names.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Link: https://lore.kernel.org/r/20201111132133.1253-1-aladyshev22@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Use hyphens instead of underscores in the MFC reserved memory node names
which is expected by naming convention, multiple dtschema files and
pointed out by dtc W=2 builds.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-5-krzk@kernel.org
Use hyphens instead of underscores in the Exynos5250 and Exynos542x node
names which is expected by naming convention, multiple dtschema files
and pointed out by dtc W=2 builds.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-4-krzk@kernel.org
Use hyphens instead of underscores in the Exynos4210 and Exynos4412 node
names which is expected by naming convention, multiple dtschema files
and pointed out by dtc W=2 builds. Use also generic "ppmu" node name
for PPMU nodes to match Devicetree specification.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-2-krzk@kernel.org
Use hyphens instead of underscores in the Exynos3250 node names which is
expected by naming convention, multiple dtschema files and pointed out
by dtc W=2 builds. Use also generic "ppmu" node name for PPMU nodes to
match Devicetree specification.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201105184506.215648-1-krzk@kernel.org
This patch adds an 'interconnects' property to Exynos4412 DTS in order to
declare the interconnect path used by the mixer. Please note that the
'interconnect-names' property is not needed when there is only one path in
'interconnects', in which case calling of_icc_get() with a NULL name simply
returns the right path.
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20201104103657.18007-7-s.nawrocki@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the following properties for Exynos4412 interconnect
bus nodes:
- interconnects: to declare connections between nodes in order to
guarantee PM QoS requirements between nodes,
- #interconnect-cells: required by the interconnect framework,
- samsung,data-clk-ratio: which allows to specify minimum data clock
frequency corresponding to requested bandwidth for each bus.
Note that #interconnect-cells is always zero and node IDs are not
hardcoded anywhere.
Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20201104103657.18007-6-s.nawrocki@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add section for kionix kxtf9.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
[tony@atomide.com: removed extra header from description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove xt894 specific things from motorola-mapphone-common.dtsi and add
them to omap4-droid4-xt894.dts and omap4-droid-bionic-xt875.dts as
applicable.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
[tony@atomide.com: shortened subject, wrapped description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/omap3-beagle-xm.dt.yaml
CHECK arch/arm/boot/dts/omap3-beagle-xm.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-beagle-xm.dt.yaml: pwmleds: 'pmu_stat' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-beagle-xm-ab.dt.yaml
CHECK arch/arm/boot/dts/omap3-beagle-xm-ab.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-beagle-xm-ab.dt.yaml: pwmleds: 'pmu_stat' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-alto35.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-alto35.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-alto35.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-chestnut43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-chestnut43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-chestnut43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-gallop43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-gallop43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-gallop43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-palo35.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-palo35.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-palo35.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-palo43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-palo43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-palo43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-alto35.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-alto35.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-alto35.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-chestnut43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-chestnut43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-gallop43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-gallop43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-gallop43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-palo35.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-palo35.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-palo35.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-palo43.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-palo43.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-palo43.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-summit.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-summit.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-summit.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-tobi.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-tobi.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-tobi.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-storm-tobiduo.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-storm-tobiduo.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-storm-tobiduo.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-summit.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-summit.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-summit.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-tobi.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-tobi.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-tobi.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap3-overo-tobiduo.dt.yaml
CHECK arch/arm/boot/dts/omap3-overo-tobiduo.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap3-overo-tobiduo.dt.yaml: pwmleds: 'overo' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap4-kc1.dt.yaml
CHECK arch/arm/boot/dts/omap4-kc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap4-kc1.dt.yaml: pwmleds: 'green', 'orange' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap4-sdp.dt.yaml
CHECK arch/arm/boot/dts/omap4-sdp.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap4-sdp.dt.yaml: pwmleds: 'charging', 'kpad' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/omap4-sdp-es23plus.dt.yaml
CHECK arch/arm/boot/dts/omap4-sdp-es23plus.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/omap4-sdp-es23plus.dt.yaml: pwmleds: 'charging', 'kpad' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Syonpsys IP cores are supposed to be defined with "snps" vendor-prefix.
Use it instead of the deprecated "synopsys" one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wl271 bluetooth uart is connected to uart2.
Setup a serdev uart child and separate bluetooth and uart2 pinmux
from wl12xx pinmux to better group the pins and muxes.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmux control register offset passed to OMAP4_IOPAD is odd.
Fixes: ab9a13665e ("ARM: dts: pandaboard: add gpio user button")
Cc: stable@vger.kernel.org
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e1 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Van der Laan LANMCU is a module for the food storage rooms to control
proper gas composition.
Co-developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Altesco (Altus-Escon-Company BV) I6P is a part of the diagnostic system
for the vehicle inspection stations.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mark the STMPE resistive touch controller as a wakeup-source.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PHYTEC PEB-AV-02 adapter adds the capability to connect a parallel
LCD display to the phyBOARD-Segin full featured, either with capacitive
or resistive touch.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a PHYTEC phyBOARD-Segin full featured with phyCORE-i.MX 6UL with
eMMC and following features:
- i.MX 6UL
- 512 MB RAM
- eMMC
- USB Host/OTG
- 2x 100 Mbit/s Ethernet
- RS232
- CAN
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The VDDA LDO1 PMIC output supplies the analog VDDA input of the
STM32MP1 on DHCOM, keep it always on, otherwise there could be
leakage through the SoC.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The VIO regulator is supplied by PMIC Buck3, describe this in the DT.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On the prototype DHCOM, the LED5 was connected to pin PG2 of the
STM32MP15xx, however on the production SoM this was changed to pin
PC6. Update the connection in the DT.
Fixes: 81d5fc7197 ("ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On the prototype DHCOM, the TA3-GPIO-C button was connected to pin PI11 of
the STM32MP15xx, however on the production SoM this was changed to pin PG0
to free up the IRQ line 11 for LAN8710i PHY IRQ. Update the connection in
the DT. Since the IRQ line 0 is used for PMIC as well and cannot be shared
with the button, make the button polled.
Fixes: 87cabf9405 ("ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rename the DSI controller nodes from "dsi-controller@"
to "dsi@" so they match the naming convention in the
YAML schema for DSI controllers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201104133758.1373298-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NanoPi R1 is a complete open source board developed
by FriendlyElec for makers, hobbyists, fans and etc.
NanoPi R1 key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 512MB/1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet x 1
- 10/100 Ethernet x 1
- Wifi 802.11b/g/n
- Bluetooth 4.0
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201102100157.85801-2-mtwget@gmail.com
The Elimo Engineering Initium is an Open Source Hardware Single Board
Computer based on the Elimo Impetus SoM.
It is meant as the first development platform for the Impetus, providing
convenient access to the peripherals on the Impetus.
It provides:
USB-C power input
UART-to-USB bridge on the USB-C connector, connected to UART1
USB-A connector for USB2.0 (Host, Device, OTG)
Audio Line In/Out
Pin header to access all signals on the M2 connector of the SoM
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201105183231.12952-4-matteo.scordino@gmail.com
The Elimo Engineering Impetus is an Open Source Hardware System-on-Module
based on the SoChip S3 SoC.
It is meant for integration into carrier boards or, more generally,
larger designs, and uses an M2 connector to facilitate that.
Interfaces on the M.2/NGFF 42mm connector:
WiFi IEEE 802. 11abgn (on-module Realtek)
Bluetooth 4.2/BLE (on-module Realtek)
RGB LCD Interface (on-module connector)
MIPI Camera Interface (on-module connector)
IEEE 802. 3u Ethernet MAC (external connecto)
USB2.0 (Host, Device, OTG) (external connector)
Audio Line In/Out (external connector)
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201105183231.12952-2-matteo.scordino@gmail.com
Add a placeholder for a MAC address. A bootloader may fill it
to set the MAC address and override EEPROM settings.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201001135254.28178-1-l.stelmach@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add Ethernet interface description for Odroid X/X2.
Add an alias to enable bootloaders to find the Ethernet interface
and assign a MAC address.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201103184412.18874-7-l.stelmach@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add Ethernet interface description for Odroid U3.
Add an alias to enable bootloaders to find the Ethernet interface
and assign a MAC address.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201103184412.18874-6-l.stelmach@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add Ethernet interface description for Odroid XU.
Add an alias to enable bootloaders to find the Ethernet interface
and assign a MAC address.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201103184412.18874-5-l.stelmach@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add Ethernet interface description for Odroid XU3 Lite.
Add an alias to enable bootloaders to find the Ethernet interface
and assign a MAC address.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201103184412.18874-4-l.stelmach@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
MicroUSB port on OdroidU3+ boards can operate both as peripheral or as
host port. Till now it was configured as pheriperal only port, but it
turned out that the DWC2 driver code already handles everything needed to
support USB role-switch, so switch it to dual-role (OTG) mode. This has
no effect on OdroidU3 (without 'plus') and OdroidX2, which doesn't have
USB needed ID pin and VBUS wiring. Those will still operate correctly in
pheriperal mode only.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20201103140214.21690-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
i.MX pinctrl group nodes should have names that ends with 'grp'.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add usb alias for bootloader searching the controller in correct order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: 23edc168bd ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e1970 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org
The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8a5b272fbf ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org
Enable the USB 2.0 Virtual Hub Controller and
the Video Engine with it's reserved memory region for the implementation
of the iKVM functionality in the BMC.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201027123722.2935-3-aladyshev22@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The KCS interface on the LPC channel 3 in the controller
is used for the in-band BMC<->BIOS IPMI communication.
0xCA2 is a default host CPU LPC IO address for this
interface.
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201027123722.2935-2-aladyshev22@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
I2C1 can be exposed through PB pins in addition to PE pins on the V3s.
Add the device-tree description for these pins.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201031182137.1879521-4-contact@paulk.fr
The compatible string in the Pine64 Pinecube dts diverges from the ones
used in other S3 based boards, like the LicheePi and the Elimo Impetus
and Initium. Discussion on LKML decided the PineCube should align to the
others.
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201030234325.5865-7-matteo.scordino@gmail.com
The Allwinner V3 and S3 can use PG6/7 as RX/TX for UART1. Since no other
functions are assigned to those pins, they are a convenient choice for
a debugging or application UART.
This is specific to V3/S3 as the V3s's non-BGA package did not have
those pins.
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201030234325.5865-3-matteo.scordino@gmail.com
Removed vuart for facebook tiogapass platform as it uses uart2 and
uart3 pin with aspeed uart routing feature.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Fixes: ffdbf49482 ("ARM: dts: aspeed: tiogapass: Enable VUART")
Link: https://lore.kernel.org/r/20200813190431.3331026-1-vijaykhemka@fb.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Due to bug in the bootloader, the PHY has floating address and may
randomly change on each PHY reset. To avoid it, the updated bootloader
with the following patch[0] should be used:
| ARM: protonic: disable on-die termination to fix PHY bootstrapping
|
| If on-die termination is enabled, the RXC pin of iMX6 will be pulled
| high. Since we already have an 10K pull-down on board, the RXC level on
| PHY reset will be ~800mV, which is mostly interpreted as 1. On some
| reboots we get 0 instead and kernel can't detect the PHY properly.
|
| Since the default 0x020e07ac value is 0, it is sufficient to remove this
| entry from the affected imxcfg files.
|
| Since we get stable 0 on pin PHYADDR[2], the PHY address is changed from
| 4 to 0.
With latest bootloader update, the PHY address will be fixed to "0".
[0] https://git.pengutronix.de/cgit/barebox/commit/?id=93f7dcf631edfcda19e7757b28d66017ea274b81
Fixes: 0d446a5055 ("ARM: dts: add Protonic PRTI6Q board")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ZII devel B board has two generations of Marvell Switches. The
mv88e6352 supports an MDIO clock of 12MHz. However the older 88e6185
does not like 12MHz, and often fails to probe.
Reduce the clock speed to 5MHz, which seems to work reliably.
Cc: Chris Healy <cphealy@gmail.com>
Fixes: b955387667 ("ARM: dts: ZII: update MDIO speed and preamble")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The extra 0 only adds one point in the userspace visible range,
so this change is almost a noop with the current driver behavior.
We don't need the 0% point, userspace seems to handle this just fine
because it uses the bl_power property to turn off the display.
Furthermore after adding "backlight: pwm_bl: Fix interpolation" patch,
the backlight interpolation will work a little differently. So we need
to preemptively remove the 0-3 segment since otherwise we would have a
252 long interpolation that would slowly go between 0 and 3, looking
really bad in userspace. So it's almost a noop/cleanup now, but it will
be required in the future.
Signed-off-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20201021220404.v3.1.I96b8d872ec51171f19274e43e96cadc092881271@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After this patch we need 2 arguments less for the fsl,stop-mode
property:
| commit d9b081e3fc
| Author: Marc Kleine-Budde <mkl@pengutronix.de>
| Date: Sun Jun 14 21:09:20 2020 +0200
|
| can: flexcan: remove ack_grp and ack_bit handling from driver
|
| Since commit:
|
| 048e3a34a2 can: flexcan: poll MCR_LPM_ACK instead of GPR ACK for stop mode acknowledgment
|
| the driver polls the IP core's internal bit MCR[LPM_ACK] as stop mode
| acknowledge and not the acknowledgment on chip level.
|
| This means the 4th and 5th value of the property "fsl,stop-mode" isn't used
| anymore. This patch removes the used "ack_gpr" and "ack_bit" from the driver.
This patch removes the two last arguments, as they are not needed
anymore.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/imx53-ppd.dt.yaml
CHECK arch/arm/boot/dts/imx53-ppd.dt.yaml
arch/arm/boot/dts/imx53-ppd.dt.yaml: leds-brightness: 'alarm-brightness' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml
CHECK arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml
arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dt.yaml: pwmleds: 'front' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml
CHECK arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml
arch/arm/boot/dts/imx6sx-softing-vining-2000.dt.yaml: pwmleds: 'blue', 'green', 'red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WaRP7 board (Wearable Development Platform) was apparently made by
Element14, not by "Warp". Correct the vendor in compatible to reflect
this. The compatibles were not documented in the bindings before.
Link: https://www.element14.com/community/docs/DOC-79058
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WaRP board (Wearable Development Platform) was apparently made by
Revolution Robotics, Inc (brand: Revotics), not by "Warp". Correct the
vendor in compatible to reflect this. The compatibles were not
documented in the bindings before.
Link: https://revotics.com/warp
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Aristainetos and Aristainetos2 boards have only SoC compatible.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are four flavors of TechNexion PICO-IMX6 boards. They have their
own DTSes, even though in Dwarf, Nymph and Pi are exactly the same.
They also have their own bindings so adjust the compatibles to match the
bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dtschema expects watchdog device node name to be "watchdog":
arch/arm/boot/dts/vf500-colibri-eval-v3.dt.yaml: wdog@4003e000:
$nodename:0: 'wdog@4003e000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dtschema expects watchdog device node name to be "watchdog":
arch/arm/boot/dts/imx31-bug.dt.yaml: wdog@53fdc000:
$nodename:0: 'wdog@53fdc000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-10-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-9-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-8-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-7-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-5-krzk@kernel.org
Using full paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-4-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-3-krzk@kernel.org
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-2-krzk@kernel.org
Add a node for the BCM4334 Bluetooth chip on the serial bus #0 on
the Exynos4412-based Midas board family.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201027142330.5121-3-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM4330 Bluetooth chip on the serial bus #0 on
the Exynos4210-based Universal C210 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201027142330.5121-2-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/at91-kizbox2-2.dt.yaml
CHECK arch/arm/boot/dts/at91-kizbox2-2.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/at91-kizbox2-2.dt.yaml: pwm_leds: 'blue', 'green', 'red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
DTC arch/arm/boot/dts/at91-kizbox3-hs.dt.yaml
CHECK arch/arm/boot/dts/at91-kizbox3-hs.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/at91-kizbox3-hs.dt.yaml: pwm_leds: 'blue', 'green', 'red', 'white' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
(Warnings above are for armv7 only, armv5 would produce similar warnings.)
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201005203451.9985-6-post@lespocky.de
Do it the simple way like for the other kizbox boards. This will allow
renaming the led controller node name later without breaking things.
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201005203451.9985-5-post@lespocky.de
Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add description for Vin power supply and for peripherals that
are supplied by Vin.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Defining the EEPROM pagesize can increase the write speed significantly.
Set it to the pagesize stated in the EEPROM's datasheet for
phyCORE-i.MX 6UL, phyCORE-i.MX 6 and phyFLEX-i.MX 6.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set the correct EEPROM compatible for phyCORE-i.MX 6 and phyFLEX-i.MX 6,
as stated in the device tree bindings.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The touchscreen subnode name needs to be stmpe_touchscreen as mentioned
in the dt-bindings.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USBOTG1 has a Micro-USB port that can be used in host mode (using an OTG
cable) or device mode.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The UART7 interface is connected to a full-duplex RS485 transceiver.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MBa7x is equipped with a TI TLV320AIC3204 audio codec.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Together with the recently merged support for alias-based MMC host
numbering, this makes the MMC devices names match what the bootloader
expects.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The external watchdog reset is necessary, as the internal reset is
unreliable on i.MX7.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock outputs are not connected. Disable them to improve EMI
behaviour.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These properties were never supported by the DP83867, and a patch
implementing them was rejected in favor of a different solution. Remove
them.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This property was never set correctly; it should have been num-cs. As
num-cs support is being removed as well, simply drop it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding display timings directly on device tree files make it difficult
to maintain as a same copy of timings may exist on different files or
panel-simple driver.
We have a panel-simple driver for this particular usage so supporting
on this driver will help to use the same timings on any device tree
files if the board mounted on a similar vendor display.
Engicam C.TOUCH OF 10.1" LCD board uses Ampire 10.1" TFT LCD and
it has supported by panel-simple already, so simply use that binding.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add GPIO STRAP_BMC_BATTERY_GPIOS5, which is used for battery
adc sensor.
Change the INTRUDER_N to CHASSIS_INTRUSION, to make it
more meaningful.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201014083057.1026-1-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The g220a is a server platform with an ASPEED AST2500 BMC.
Signed-off-by: Lotus Xu <xuxiaohan@bytedance.com>
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200929063955.1206-2-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is an alternate layout used by OpenBMC systems
The division of space is as follows:
u-boot + env: 0.5MB
kernel/FIT: 5MB
rofs: 42.5MB
rwfs: 16MB
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20200929063955.1206-1-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The VGA memory region is always from the top of RAM. On this board, that
is 0x80000000 + 0x20000000 - 0x01000000 = 0x9f000000.
This was not an issue in practice as the region is "reserved" by the
vendor's u-boot reducing the amount of available RAM, and the only user
is the host VGA device poking at RAM over PCIe. That is, nothing from
the ARM touches it.
It is worth fixing as developers copy existing device trees when
building their machines, and the XDMA driver does use the memory region
from the ARM side.
Fixes: c4043ecac3 ("ARM: dts: aspeed: Add S2600WF BMC Machine")
Reported-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20200922064234.163799-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
KCS nodes compatible property was changed in the dtsi to use v2 binding
before ethanolx was merged, making the ethanolx device tree incorrect.
Update it to use the new binding so the driver loads.
Fixes: fa4c8ec6fe ("ARM: dts: aspeed: Change KCS nodes to v2 binding")
Signed-off-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201027123722.2935-1-aladyshev22@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO controller is a GPIO controller followed by some SGPIO
controllers, which are a different type of device with their own binding
and drivers.
Make the gpio node cover the only conventional GPIO controller.
Fixes: 8dbcb5b709 ("ARM: dts: aspeed-g6: Add gpio devices")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201012033150.21056-2-billy_tsai@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Commits 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") and 9ff416cf45 ("ARM: dts:
exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family")
revealed that 'opp-shared' property for the Exynos bus OPPs was used
incorrectly, what had the side-effect of disabling frequency scaling for
the second and latter buses sharing given OPP-table.
Fix this by removing bogus 'opp-shared' properties from Exynos4412 bus
OPP-tables. This restores frequency scaling for the following buses:
C2C, RightBus, and MFC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200911122236.16805-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commits 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") and 9ff416cf45 ("ARM: dts:
exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family")
revealed that 'opp-shared' property for the Exynos bus OPPs was used
incorrectly, what had the side-effect of disabling frequency scaling for
the second and latter buses sharing given OPP-table.
Fix this by removing bogus 'opp-shared' properties from Exynos3 bus
OPP-tables. This restores frequency scaling for the following buses:
RightBus, LCD0, FSYS and MFC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200911122220.13698-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The ZeroPi is another fun board developed
by FriendlyELEC for makers,
hobbyists and fans.
ZeroPi key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201026073536.13617-2-mtwget@gmail.com
The interrupts in Dynamic Memory Controller in Exynos5422 and Odroid
XU3-family boards are no longer needed. They have been used in order
to workaround some issues in scheduled work in devfreq. Now when the
devfreq framework design is improved, remove the interrupt driven
approach and rely on devfreq monitoring mechanism with fixed intervals.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20200708153420.29484-3-lukasz.luba@arm.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201020115959.2658-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Syonpsys IP cores are supposed to be defined with "snps" vendor-prefix.
Use it instead of the deprecated "synopsys" one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201020115959.2658-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Odroid XU has external pull ups for USB 3.0 over-current pins, so
disable the internal one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-4-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c75 ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb08965622 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
On Odroid XU board the USB3-0 port is a microUSB and USB3-1 port is USB
type A (host). The roles were copied from Odroid XU3 (Exynos5422)
design which has it reversed.
Fixes: 8149afe4db ("ARM: dts: exynos: Add initial support for Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-1-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
arch/arm/boot/dts/exynos5410-odroidxu.dt.yaml: pwmleds:
'blueled', 'greenled' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
arch/arm/boot/dts/exynos5422-odroidhc1.dt.yaml: pwmleds:
'blueled' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Link: https://lore.kernel.org/r/20201005203451.9985-8-post@lespocky.de
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Samsung Galaxy S5 (klte), has 3 SDHCI nodes used for internal
storage, WiFi, external SD card slot. The external SD card slot is
similar to the internal storage.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200920144859.813032-8-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy S5 has a GPIO Expander chip, the PCAL6416A with 16
ports on a i2c bus. These pins are used for WiFi, NFC, IR among other
things.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200920144859.813032-6-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the touchkey found on the Samsung Galaxy S5. The
touchkey is responsible for handling the application and back buttons
found around the home button.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200920144859.813032-3-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e7 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee415f ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org
The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 98048143b7 ("ARM: dts: sun9i: cubieboard4: Enable GMAC")
Fixes: bc9bd03a44 ("ARM: dts: sun9i: a80-optimus: Enable GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-7-wens@kernel.org
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org
The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: 7a78ef92cd ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org
The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 04c85ecad3 ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org
The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 67073d9767 ("ARM: dts: sun7i: cubietruck: Enable the GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org
The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: c220aec2bb ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org
This reverts commit 75ee680cbd.
Turns out the activity and link LEDs on the RJ45 port are active low,
just like on the Orange Pi PC.
Revert the commit that says otherwise.
Fixes: 75ee680cbd ("arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high")
Fixes: 4904337fe3 ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-1-wens@kernel.org
The camera interfaces on MMP3 are on a separate power island that needs
to be turned on for them to operate and, ideally, turned off when the
cameras are not in use.
This hooks the power island with the camera interfaces in the device
tree.
Link: https://lore.kernel.org/r/20200925234805.228251-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX3rp4gAKCRDj7w1vZxhR
xaRwAP4+mbK4rFo7Klrk0pE5qaJyXBEHXDN0VmRu6bwnGujWdgEAitXGA7k0v+5a
qZxm4E1muL+wNE2jmTyb1aJpwrrD9wA=
=/efk
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
One fix for an unreasonable thermal trip point on the A10
* tag 'sunxi-fixes-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun4i-a10: fix cpu_alert temperature
Link: https://lore.kernel.org/r/3c95a95f-c6fa-4b34-823b-ddaa7660d274.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The iwg21d comes with a 7" capacitive touch screen, therefore
add support for it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200929140502.16017-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
dtschema for GPIO controllers expects GPIO hogs to end with 'hog'
suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
I had queued up a batch of fixes that got a bit close to the release for
sending in before the merge window opened, so I'm including them in the
batch of pull requests instead. They're mostly smaller DT tweaks and
fixes, the usual mix that we tend to have through the releases.
-----BEGIN PGP SIGNATURE-----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=tvbv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
for sending in before the merge window opened, so I'm including them
in the merge window batch instead.
Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
through the releases"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
soc: actions: include header to fix missing prototype
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
soc: qcom: pdr: Fixup array type of get_domain_list_resp message
arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
arm64: dts: sdm630: Temporarily disable SMMUs by default
arm64: dts: sdm845: Fixup OPP table for all qup devices
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
soc: xilinx: Fix error code in zynqmp_pm_probe()
cros-ec:
* Error code cleanup across cros-ec by Guenter.
* Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status.
cros_ec_typec:
* Landed initial USB4 support in typec connector class driver for cros_ec.
* Role switch bugfix on disconnect, and reordering configuration steps.
cros_ec_lightbar:
* Fix buffer outsize and result for get_lightbar_version.
misc:
* Remove config MFD_CROS_EC, now that transition from MFD is complete.
* Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard keymap.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCX5G2IAAKCRBzbaomhzOw
wo4JAQC7BcJJwYgoVnRQvYd4xXCEsl/F9cVFJJLRYAH/PA4x6gEA+wfdIxebAXbO
RapU2HOppxiQGFkr+0FX5xV+O7cRNAo=
=gkul
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros-ec:
- Error code cleanup across cros-ec by Guenter
- Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status
cros_ec_typec:
- Landed initial USB4 support in typec connector class driver for
cros_ec
- Role switch bugfix on disconnect, and reordering configuration
steps
cros_ec_lightbar:
- Fix buffer outsize and result for get_lightbar_version
misc:
- Remove config MFD_CROS_EC, now that transition from MFD is complete
- Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard
keymap"
* tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
ARM: dts: cros-ec-keyboard: Add alternate keymap for KEY_LEFTMETA
platform/chrome: Use kobj_to_dev() instead of container_of()
platform/chrome: cros_ec_proto: Drop cros_ec_cmd_xfer()
platform/chrome: cros_ec_proto: Update cros_ec_cmd_xfer() call-sites
platform/chrome: Kconfig: Remove the transitional MFD_CROS_EC config
platform/chrome: cros_ec_lightbar: Reduce ligthbar get version command
platform/chrome: cros_ec_trace: Add fields to command traces
platform/chrome: cros_ec_typec: Re-order connector configuration steps
platform/chrome: cros_ec_typec: Avoid setting usb role twice during disconnect
platform/chrome: cros_ec_typec: Send enum values to usb_role_switch_set_role()
platform/chrome: cros_ec_typec: USB4 support
pwm: cros-ec: Simplify EC error handling
platform/chrome: cros_ec_proto: Convert EC error codes to Linux error codes
platform/input: cros_ec: Replace -ENOTSUPP with -ENOPROTOOPT
pwm: cros-ec: Accept more error codes from cros_ec_cmd_xfer_status
platform/chrome: cros_ec_sysfs: Report range of error codes from EC
cros_ec_lightbar: Accept more error codes from cros_ec_cmd_xfer_status
iio: cros_ec: Accept -EOPNOTSUPP as 'not supported' error code
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Including:
- ARM-SMMU Updates from Will:
- Continued SVM enablement, where page-table is shared with
CPU
- Groundwork to support integrated SMMU with Adreno GPU
- Allow disabling of MSI-based polling on the kernel
command-line
- Minor driver fixes and cleanups (octal permissions, error
messages, ...)
- Secure Nested Paging Support for AMD IOMMU. The IOMMU will
fault when a device tries DMA on memory owned by a guest. This
needs new fault-types as well as a rewrite of the IOMMU memory
semaphore for command completions.
- Allow broken Intel IOMMUs (wrong address widths reported) to
still be used for interrupt remapping.
- IOMMU UAPI updates for supporting vSVA, where the IOMMU can
access address spaces of processes running in a VM.
- Support for the MT8167 IOMMU in the Mediatek IOMMU driver.
- Device-tree updates for the Renesas driver to support r8a7742.
- Several smaller fixes and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----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=C0Sg
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM-SMMU Updates from Will:
- Continued SVM enablement, where page-table is shared with CPU
- Groundwork to support integrated SMMU with Adreno GPU
- Allow disabling of MSI-based polling on the kernel command-line
- Minor driver fixes and cleanups (octal permissions, error
messages, ...)
- Secure Nested Paging Support for AMD IOMMU. The IOMMU will fault when
a device tries DMA on memory owned by a guest. This needs new
fault-types as well as a rewrite of the IOMMU memory semaphore for
command completions.
- Allow broken Intel IOMMUs (wrong address widths reported) to still be
used for interrupt remapping.
- IOMMU UAPI updates for supporting vSVA, where the IOMMU can access
address spaces of processes running in a VM.
- Support for the MT8167 IOMMU in the Mediatek IOMMU driver.
- Device-tree updates for the Renesas driver to support r8a7742.
- Several smaller fixes and cleanups all over the place.
* tag 'iommu-updates-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (57 commits)
iommu/vt-d: Gracefully handle DMAR units with no supported address widths
iommu/vt-d: Check UAPI data processed by IOMMU core
iommu/uapi: Handle data and argsz filled by users
iommu/uapi: Rename uapi functions
iommu/uapi: Use named union for user data
iommu/uapi: Add argsz for user filled data
docs: IOMMU user API
iommu/qcom: add missing put_device() call in qcom_iommu_of_xlate()
iommu/arm-smmu-v3: Add SVA device feature
iommu/arm-smmu-v3: Check for SVA features
iommu/arm-smmu-v3: Seize private ASID
iommu/arm-smmu-v3: Share process page tables
iommu/arm-smmu-v3: Move definitions to a header
iommu/io-pgtable-arm: Move some definitions to a header
iommu/arm-smmu-v3: Ensure queue is read after updating prod pointer
iommu/amd: Re-purpose Exclusion range registers to support SNP CWWB
iommu/amd: Add support for RMP_PAGE_FAULT and RMP_HW_ERR
iommu/amd: Use 4K page for completion wait write-back semaphore
iommu/tegra-smmu: Allow to group clients in same swgroup
iommu/tegra-smmu: Fix iova->phys translation
...
Pull opertaing performance points (OPP) framework fixes for 5.10-rc1
from Viresh Kumar:
"- Return -EPROBE_DEFER properly from dev_pm_opp_get_opp_table()
(Stephan Gerhold).
- Minor cleanups around required-opps (Stephan Gerhold).
- Extends opp-supported-hw property to contain multiple versions
(Viresh Kumar).
- Multiple cleanups around dev_pm_opp_attach_genpd() (Viresh Kumar).
- Multiple fixes, cleanups in the OPP core for overall better design
(Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Allow opp-level to be set to 0
opp: Prevent memory leak in dev_pm_opp_attach_genpd()
ARM: tegra: Pass multiple versions in opp-supported-hw property
opp: Allow opp-supported-hw to contain multiple versions
dt-bindings: opp: Allow opp-supported-hw to contain multiple versions
opp: Set required OPPs in reverse order when scaling down
opp: Reduce code duplication in _set_required_opps()
opp: Drop unnecessary check from dev_pm_opp_attach_genpd()
opp: Handle multiple calls for same OPP table in _of_add_opp_table_v1()
opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER
opp: Remove _dev_pm_opp_find_and_remove_table() wrapper
opp: Split out _opp_set_rate_zero()
opp: Reuse the enabled flag in !target_freq path
opp: Rename regulator_enabled and use it as status of all resources
When running dtbs_check thermal_zone warn about the
temperature declared.
thermal-zones: cpu-thermal:trips:cpu-alert0:temperature:0:0: 850000 is greater than the maximum of 200000
It's indeed wrong the real value is 85°C and not 850°C.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201003100332.431178-1-peron.clem@gmail.com
Even though the SP804 binding allows to specify only one clock, the
primecell driver requires a named clock to activate the bus clock.
Specify the one clock three times and provide some clock-names, to
make the DT match the SP804 and primecell binding.
Link: https://lore.kernel.org/r/20200907121831.242281-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the dtsi/dts files have been moved some includes are now
broken so this fixes up the includes so the dtbs build again.
Link: https://lore.kernel.org/r/20201002133418.2250277-6-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since we now have support for the interrupt controller pm_uart's
interrupt is routed through it make sense to wire up it's interrupt
in the device tree.
The interrupt is the same for all known chips so it goes in the
base dtsi.
Link: https://lore.kernel.org/r/20201002133418.2250277-4-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the IRQ and FIQ intc instances to the base MStar/SigmaStar v7
dtsi. All of the known SoCs have both and at the same place with
their common IPs using the same interrupt lines.
Link: https://lore.kernel.org/r/20201002133418.2250277-3-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix the system controller compatible for the hi3620 and hip04 SoCs
- Add the basic device tree for the hisilicon SD5203 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qsbd
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm32-dt-for-5.10-tag2' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs DT updates for 5.10 (take two)
- Fix the system controller compatible for the hi3620 and hip04 SoCs
- Add the basic device tree for the hisilicon SD5203 SoC
* tag 'hisi-arm32-dt-for-5.10-tag2' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
Link: https://lore.kernel.org/r/5F742717.5080405@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Some more dts changes that did not make it to the first set of
dts changes:
- Drop unnessary nokia,nvm-size property
- A series of changes to use "okay" instead of "ok"
- A series of changes to move boards to use new cpsw switch
driver and drop the drop legacy cpsw dt node
- A series of changes to fix issues with the GPIO binding
usage
-----BEGIN PGP SIGNATURE-----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=Df2a
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.10/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More dts changes for omaps for v5.10 merge window
Some more dts changes that did not make it to the first set of
dts changes:
- Drop unnessary nokia,nvm-size property
- A series of changes to use "okay" instead of "ok"
- A series of changes to move boards to use new cpsw switch
driver and drop the drop legacy cpsw dt node
- A series of changes to fix issues with the GPIO binding
usage
* tag 'omap-for-v5.10/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3874: iceboard: fix GPIO expander reset GPIOs
ARM: dts: am335x: t335: align GPIO hog names with dtschema
ARM: dts: am335x: lxm: fix PCA9539 GPIO expander properties
ARM: dts: am437x-l4: drop legacy cpsw dt node
ARM: dts: am437x: switch to new cpsw switch drv
ARM: dts: am437x-l4: add dt node for new cpsw switchdev driver
ARM: dts: dra7: drop legacy cpsw dt node
ARM: dts: am57xx-cl-som-am57x: switch to new cpsw switch drv
ARM: dts: dra7x-evm: switch to new cpsw switch drv
ARM: dts: beagle-x15: switch to new cpsw switch drv
ARM: dts: am57xx-idk: switch to new cpsw switch drv
ARM: dts: am5729: beagleboneai: switch to new cpsw switch drv
ARM: dts: am43xx: replace status value "ok" by "okay"
ARM: dts: dra7xx: replace status value "ok" by "okay"
ARM: dts: omap: replace status value "ok" by "okay"
ARM: dts: n9, n950: Remove nokia,nvm-size property
Link: https://lore.kernel.org/r/pull-1601445968-476435@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
and the pinecube board
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX3HKAwAKCRDj7w1vZxhR
xc3bAQCcnys+hZ4XtwA/GIT10zcvpBVkUrjU56zZPG9WiEA9AgD/S9PN5m6J0R7O
F8dU+0Xx8O+3KNwIhuqEw2Mj7WHpcwE=
=6hIV
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
A few more DT patches for 5.10, to support simple-framebuffer on the v3s
and the pinecube board
* tag 'sunxi-dt-for-5.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: v3s: Add simple-framebuffer
ARM: dts: sun8i: s3l: add support for Pine64 PineCube IP camera
dt-bindings: arm: sunxi: add Pine64 PineCube binding
ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for I2C1 at PE bank
ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for 8-bit parallel CSI
ARM: dts: sun8i: V3/V3s/S3/S3L: add CSI1 device node
ARM: dts: sun8i: V3/V3s/S3/S3L: add pinctrl for UART2 RX/TX
ARM: dts: sun8i: V3/V3s/S3/S3L: add Ethernet support
Link: https://lore.kernel.org/r/e7c12b59-8603-438d-908b-5f0bde2c8697.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
and a spelling for the status property.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl9ryJUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWLgB/0fWWkgfABOtcqPv30NQwThE5d/zzGtS5vu
IBMdWK6EWgqT7eUcd/rVhfEJo+YuIyOfKU0AEKROyK/XjCaThgp4ERqpf4Obv3yf
T1mhTfqBbGt3fF39NTNBSUWO2kywOnZa32pUDZcckFgQEpSQNHsW8NYM7W0tj9Z7
GB0aMij23ps5ckN8bVd9ZSdwkTIu0hfr1o/GQRLhKbtrs/+CiJERjcfJVyKvKc5w
ieqaGyHvJ9Bjw83muHN2EUL7gJHQvo6WJI7XFiUxqSDOw4WqM/3UgganRVdwDpp6
88gBLRAWw2CUK5WMlQx2oJ8eiUZQL6eckJNM3+0NoP5LA8Owd6bI
=EIWN
-----END PGP SIGNATURE-----
Merge tag 'v5.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
cpu-supply fixes (supply for each cpu core not only cpu0)
and a spelling for the status property.
* tag 'v5.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: replace status value "ok" by "okay"
ARM: dts: rockchip: update cpu supplies on rk3066a
ARM: dts: rockchip: rk3066a: add label to cpu@1
ARM: dts: rockchip: update cpu supplies on rk3288
Link: https://lore.kernel.org/r/1834049.gShM3QRH0n@diego
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add devicetree support for Caninos Loucos Labrador SBC manufactured
by Laboratory of Integrated Technological Systems (LSI-TEC), Brazil.
This board is based on Actions Semi S500 SoC. More information about
this board can be found in their website: https://caninosloucos.org/en/
- Fix PPI interrupt specifiers for peripherals attached to Cortex-A9 CPU
- Add devicetree support for RoseapplePi SBC manufactured by Roseapple Pi
team in Taiwan. This board is based on Actions Semi S500 SoC.
More information about this board can be found in their website:
http://roseapplepi.org/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAl9prhwACgkQVZ8R5v6R
zvVUKwgAp09Kdu17PUNmoqjujUmkAlANgzW30Z12ear1hSJNEoXV8ZgswAYyeerk
exPQWXEvueDYXXgXiLCjaOI8p/Ukae4wc8eaTyYN7i0JMxGQ1wnpdEI8su1VC+ph
+RuL/mH/dc/pibWMBVIf+YP4mfQz+RCX1+VRHbINKHeMuQ3rCecQ6352GZxkt/EU
3BEr2QpNBvIwMLxllUf51k/ng9w2mtEk+7uDEPJmBtUCbRUWxhq5UexAoUJbPvLU
2f8OpYh4Tbnxl/FLuRYCl0Yhk2bB9600HNhx1enK/P2u3wuJkK1tDlmLZoYOuirc
imx3OrzSnqOtAJBg2chcaY2tq+SUtA==
=PNl0
-----END PGP SIGNATURE-----
Merge tag 'actions-arm-dt-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions into arm/dt
Actions Semi ARM DT for v5.10:
- Add devicetree support for Caninos Loucos Labrador SBC manufactured
by Laboratory of Integrated Technological Systems (LSI-TEC), Brazil.
This board is based on Actions Semi S500 SoC. More information about
this board can be found in their website: https://caninosloucos.org/en/
- Fix PPI interrupt specifiers for peripherals attached to Cortex-A9 CPU
- Add devicetree support for RoseapplePi SBC manufactured by Roseapple Pi
team in Taiwan. This board is based on Actions Semi S500 SoC.
More information about this board can be found in their website:
http://roseapplepi.org/
* tag 'actions-arm-dt-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions:
ARM: dts: owl-s500: Add RoseapplePi
ARM: dts: owl-s500: Fix incorrect PPI interrupt specifiers
ARM: dts: Add Caninos Loucos Labrador v2
Link: https://lore.kernel.org/r/20200922113712.GB11251@Mani-XPS-13-9360
Signed-off-by: Olof Johansson <olof@lixom.net>
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
-----BEGIN PGP SIGNATURE-----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=e08s
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
The 3.10 vendor kernel defines the following GPU 20 interrupt lines:
#define INT_MALI_GP AM_IRQ(160)
#define INT_MALI_GP_MMU AM_IRQ(161)
#define INT_MALI_PP AM_IRQ(162)
#define INT_MALI_PMU AM_IRQ(163)
#define INT_MALI_PP0 AM_IRQ(164)
#define INT_MALI_PP0_MMU AM_IRQ(165)
#define INT_MALI_PP1 AM_IRQ(166)
#define INT_MALI_PP1_MMU AM_IRQ(167)
#define INT_MALI_PP2 AM_IRQ(168)
#define INT_MALI_PP2_MMU AM_IRQ(169)
#define INT_MALI_PP3 AM_IRQ(170)
#define INT_MALI_PP3_MMU AM_IRQ(171)
#define INT_MALI_PP4 AM_IRQ(172)
#define INT_MALI_PP4_MMU AM_IRQ(173)
#define INT_MALI_PP5 AM_IRQ(174)
#define INT_MALI_PP5_MMU AM_IRQ(175)
#define INT_MALI_PP6 AM_IRQ(176)
#define INT_MALI_PP6_MMU AM_IRQ(177)
#define INT_MALI_PP7 AM_IRQ(178)
#define INT_MALI_PP7_MMU AM_IRQ(179)
However, the driver from the 3.10 vendor kernel does not use the
following four interrupt lines:
- INT_MALI_PP3
- INT_MALI_PP3_MMU
- INT_MALI_PP7
- INT_MALI_PP7_MMU
Drop the "pp3" and "ppmmu3" interrupt lines. This is also important
because there is no matching entry in interrupt-names for it (meaning
the "pp2" interrupt is actually assigned to the "pp3" interrupt line).
Fixes: 7d3f6b536e ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200815181957.408649-1-martin.blumenstingl@googlemail.com
On newer keyboards this key is in a different place. Add both options to
the keymap so that both new and old keyboards work.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The DT binding for Hisilicon system controllers require to have a
"syscon" compatible string.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
- Fix handling of HOST_EXTRACFLAGS for dtc
- Several warning fixes for DT bindings
-----BEGIN PGP SIGNATURE-----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=m4lt
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix handling of HOST_EXTRACFLAGS for dtc
- Several warning fixes for DT bindings
* tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
scripts/dtc: only append to HOST_EXTRACFLAGS instead of overwriting
dt-bindings: Fix 'reg' size issues in zynqmp examples
ARM: dts: bcm2835: Change firmware compatible from simple-bus to simple-mfd
dt-bindings: leds: cznic,turris-omnia-leds: fix error in binding
dt-bindings: crypto: sa2ul: fix a DT binding check warning
The current binding for the RPi firmware uses the simple-bus compatible as
a fallback to benefit from its automatic probing of child nodes.
However, simple-bus also comes with some constraints, like having the ranges,
our case.
Let's switch to simple-mfd that provides the same probing logic without
those constraints.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200924082642.18144-1-maxime@cerno.tech
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for "allwinner,simple-framebuffer"
with "mixer0-lcd0" pipeline from boot loader (u-boot).
It depends on boot loader implementation of DE2/TCON0
setup with LCD.
Signed-off-by: Martin Cerveny <m.cerveny@computer.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200916175941.8448-1-m.cerveny@computer.org
The Pine64 PineCube IP camera is an IP camera with SoChip S3 SoC.
It comes with a main board, an expansion board and a camera.
The main board features a Micro-USB power-only jack, a USB Type-A port,
an Ethernet port connected to the internal PHY of the SoC and a Realtek
RTL8189ES SDIO Wi-Fi module. A RGB LCD connector is reserved on the
board.
The expansion board features a TF slot, a microphone, a speaker
connector with on-board amplifier and a few IR LEDs.
Add support for the kit, with features on the main board and the
expansion board now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923010215.148819-2-icenowy@aosc.io
I2C1 controller is available at PE bank, usually used for
connecting an I2C-controlled camera sensor.
Add pinctrl node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923010014.148482-2-icenowy@aosc.io
The CSI1 controller of V3/V3s/S3/S3L SoCs is used for parallel CSI.
As we're going to add support for Pine64 SCC board, which uses 8-bit
parallel CSI (and the MCLK output), add the pinctrl node of 8-bit
CSI and MCLK to the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923010122.148661-1-icenowy@aosc.io
The CSI1 controller of V3/V3s/S3/S3L chips is used for parallel CSI.
Add the device tree node of it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923005858.148261-2-icenowy@aosc.io
The UART2 RX/TX pins on Allwinner V3 series is at PB0/1, which is used
as debugging UART on some boards.
Add pinctrl node for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923005858.148261-1-icenowy@aosc.io
The Allwinner V3/V3s/S3L/SoChip S3 Ethernet MAC and internal PHY is quite
similar to the ones on Allwinner H3, except for V3s the external MII is
not wired out.
Add ethernet support to V3/V3s/S3/S3L.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200923005709.147966-2-icenowy@aosc.io
- New board/device support: Tolino Shine 2 HD, TQMa6 SoM, Y Soft IOTA
Orion board.
- update GPMI NAND node name to nand-controller for aligning with DT
schema.
- Remove the legacy fsl,spi-num-chipselects property from a few board.
- A series to update imx6q-logicpd support, using GPIO chipselect,
adding board compatible string, and enabling DTB build for the board.
- Complete RNG device node in i.MX6SL device tree, and add RNG node for
i.MX6SLL and i.MX6ULL.
- Correct interrupt flags for imx6qdl-gw5xxx boards.
- Add missing enet_out clock for i.MX6Q/DL Ethernet device.
- Enable PCIe support for imx6qp-sabreauto board.
- A series from Shengjiu Wang to add audio sound card for imx7d-sdb and
imx6sll-evk board, add headphone detection for sound card on a few NXP
development boards.
- A couple of minor fix-ups on i.MX25 pin functions.
- Some random update on various boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl9qrwoUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7Fqgf/Y+6XGsUY+QHRK6CTglOsDgC43Ixw
mhJkvG7AWcu+2Oz+WLFVbncbcBBy1swrAAss0DlwAB3BXijWiytSz6flPCBHrFiN
pyM1CLhgQChI2JfWRRc1ij/WOHkztnxR7CHLOycdhn8WQLFLQeC6Axox+d22IW4L
NgbR08eq2g2+QjMjHPyGpxnCw7AoGzexCwCLC8ajKTFe16k61bkz5Q2SxXogdlkO
cusfGpdFDme04Fl/T9sWOyIO/+l1qOzDx5JIQHRVnTB8hY7Dl7r7NQYdcvcdYrIj
AR31fXEjioR5C+AYr25ZILowZlS8VyvfTi1ZFHMFG3yD+856AYqCDB40Jw==
=w/3X
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree change for 5.10:
- New board/device support: Tolino Shine 2 HD, TQMa6 SoM, Y Soft IOTA
Orion board.
- update GPMI NAND node name to nand-controller for aligning with DT
schema.
- Remove the legacy fsl,spi-num-chipselects property from a few board.
- A series to update imx6q-logicpd support, using GPIO chipselect,
adding board compatible string, and enabling DTB build for the board.
- Complete RNG device node in i.MX6SL device tree, and add RNG node for
i.MX6SLL and i.MX6ULL.
- Correct interrupt flags for imx6qdl-gw5xxx boards.
- Add missing enet_out clock for i.MX6Q/DL Ethernet device.
- Enable PCIe support for imx6qp-sabreauto board.
- A series from Shengjiu Wang to add audio sound card for imx7d-sdb and
imx6sll-evk board, add headphone detection for sound card on a few NXP
development boards.
- A couple of minor fix-ups on i.MX25 pin functions.
- Some random update on various boards.
* tag 'imx-dt-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
ARM: dts: imx6qdl-gw5xxx: correct interrupt flags
ARM: dts: imx6q-logicpd: Use GPIO chipselect
ARM: dts: imx: Add an entry for imx6q-logicpd.dtb
ARM: dts: imx6q-logicpd: Add a specific board compatible string
ARM: dts: imx6q: align GPIO hog names with dtschema
ARM: dts: imx6qdl-tqma6: fix LM75 compatible string
ARM: dts: imx6qdl-tqma6: remove obsolete fsl,spi-num-chipselects
ARM: dts: imx6qdl-tqma6: fix indentation
ARM: dts: imx28-m28: Align GPMI NAND node name with schema
ARM: dts: imx6qdl: add enet_out clk support
ARM: dts: imx6qdl: move iomuxc compatible assignment out of root node
ARM: dts: vf: Fix PCA95xx GPIO expander properties on ZII CFU1
ARM: dts: imx: add devicetree for Tolino Shine 2 HD
ARM: dts: imx6qdl-gw553x: Remove unneeded #address-cells/#size-cells
ARM: dts: imx6sll-evk: Add audio sound card node
ARM: dts: imx6sl-evk: Add headphone detection for sound card
ARM: dts: imx6sx-sdb: Add headphone detection for sound card
ARM: dts: imx6q-kontron-samx6i: Remove old fsl,spi-num-chipselects
ARM: dts: imx: Fix the SPI chipselect polarity
ARM: dts: imx25-pinfunc: Fix GPT function names
...
Link: https://lore.kernel.org/r/20200923073009.23678-4-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
a misconfigured regulator on the Bananapi M2 Ultra.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX2jLlQAKCRDj7w1vZxhR
xfeOAP9HaamZwsHuTm+4FYLhJwUe44c1cHmnRTA49I8ifWaAqwEAt0+SfFue9GG7
ToKUFegAf7NP2h82QB04a72wHBo8CQk=
=uA2F
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Two fixes for the Allwinner SoCs, one for the H5 GPU support and one for
a misconfigured regulator on the Bananapi M2 Ultra.
* tag 'sunxi-fixes-for-5.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
Link: https://lore.kernel.org/r/8a436328-b844-4599-8695-ab2088a00ade.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Further cleanup of DTS with dtschema: s5pv210, s3c6410 and s3c24xx.
This fixes many minor dtschema violations, adds few missing
functionalities (like clock for RTC) and improves the code
maintainability in few places. Except the RTC clock, this should not
have visible impact.
2. Fix few remaining Exynos dtschema violations.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAl9nebQQHGtyemtAa2Vy
bmVsLm9yZwAKCRDBN2bmhouD1zeHD/9ykZ+GLUZkUQQGjFKuCAyJsUPMUBr6+oqM
Ab8za4YXrWi/Kctp+sDp5yRl3XsgB+VgJHfP+GjQnAVmYGE3gEIpJ4Ig0iSjikWJ
Hk8tqZqQca6sOI/cfowCDAwWIPU6N1V5IO0rC7MiCdEfAFF22xhzXSp2WiFLsPHQ
cMa9pUb8KKZEA48annLXUxMjogGFdaCmFpQhugek22zfE99Zl11/PcM1U9LiHfdL
r+iHMfI5Nya/5sHKrtypdO3y8o90f/ZTDhqp2XmMa7uLgmRDvqtAuglR/Gkrnfxj
XzNYQgaa/yd6WVvXNZWUsBphSOxDE7loYwmD21yUOSP/PhuoiP4PrzbPk0ewrfZX
PRHN7NwjkFWDVaKjbsg329j30U+82SRxnJVOVbnog1l5iUQxE9/8+/I1GYt1sfGD
xNsoRJohALyifaACBNRCusauZXQkZi9LEQlYVVKSL7TLdgx76dzTyc2S39aTDYft
QQZbNZwhIOaHeFzR4Xlx/fVZUrSymzvYUOBJRs1E486zS8RK+v6J65QU6zenW2xV
2TUVsMYrzvdwBZm9GIJbhx86r5Il1iPkXzyMblgQseUgPtV5F54DloqW5pQ7V1iZ
YadW+c3EzUhHmLvvO8GCdsQrWBKZcm3eCaTttdPQD+omb5/I9imNRZ1CUyZwrp/b
qtI0QQdMzA==
=yolB
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.10, part two
1. Further cleanup of DTS with dtschema: s5pv210, s3c6410 and s3c24xx.
This fixes many minor dtschema violations, adds few missing
functionalities (like clock for RTC) and improves the code
maintainability in few places. Except the RTC clock, this should not
have visible impact.
2. Fix few remaining Exynos dtschema violations.
* tag 'samsung-dt-5.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (36 commits)
ARM: dts: s5pv210: replace deprecated "gpios" i2c-gpio property in Goni
ARM: dts: s5pv210: replace deprecated "gpios" i2c-gpio property in Aquila
ARM: dts: s5pv210: move fixed regulators under root node in Goni
ARM: dts: s5pv210: move fixed regulators under root node in Aquila
ARM: dts: exynos: Align OPP table name with dt-schema
ARM: dts: exynos: move assigned-clock* properties to i2s0 node in Odroid XU4
ARM: dts: exynos: add input clock to CMU in Exynos4412 Odroid
ARM: dts: exynos: add input clock to CMU in Exynos3250
ARM: dts: s3c24xx: move fixed clocks under root node in SMDK2416
ARM: dts: s3c24xx: add address to CPU node
ARM: dts: s3c24xx: align PWM/timer node name with dtschema
ARM: dts: s3c24xx: override nodes by label
ARM: dts: s3c24xx: fix number of PWM cells
ARM: dts: s3c6410: remove additional CPU compatible
ARM: dts: s3c6410: align node SROM bus node name with dtschema in SMDK6410
ARM: dts: s3c6410: align node SROM bus node name with dtschema in Mini6410
ARM: dts: s3c6410: move fixed clocks under root node in SMDK6410
ARM: dts: s3c6410: move fixed clocks under root node in Mini6410
ARM: dts: s5pv210: correct ethernet unit address in SMDKV210
ARM: dts: s5pv210: align SPI GPIO node name with dtschema in Aries
...
Link: https://lore.kernel.org/r/20200920160705.9651-3-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
- PCIe endpoint support for the RZ/G2H SoC,
- SATA support for the HopeRun HiHope RZ/G2H board,
- Increase support (CAN, LED, SPI NOR, VIN, VSP) for the RZ/G1H SoC on
the iWave Qseven board (G21D), and its camera add-on board,
- Initial support for the R-Car V3U SoC on the Falcon CPU and BreakOut
boards,
- HDMI display and sound support for the R-Car M3-W+ SoC on the
Salvator-XS board,
- Digital Radio Interface (DRIF) support for the R-Car E3 SoC,
- Minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX2SkmQAKCRCKwlD9ZEnx
cIXNAP0XqvKJP7xGjQ1ORyePB1nWZtebVqGoQFxpvqwznMNZlAD7BIRlATo4LYpu
LNMya5sk85WAhZNbpkHwR++3/8m+mgE=
=Va2A
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.10 (take two)
- PCIe endpoint support for the RZ/G2H SoC,
- SATA support for the HopeRun HiHope RZ/G2H board,
- Increase support (CAN, LED, SPI NOR, VIN, VSP) for the RZ/G1H SoC on
the iWave Qseven board (G21D), and its camera add-on board,
- Initial support for the R-Car V3U SoC on the Falcon CPU and BreakOut
boards,
- HDMI display and sound support for the R-Car M3-W+ SoC on the
Salvator-XS board,
- Digital Radio Interface (DRIF) support for the R-Car E3 SoC,
- Minor fixes and cleanups.
* tag 'renesas-arm-dt-for-v5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (24 commits)
arm64: dts: renesas: r8a774c0: Fix MSIOF1 DMA channels
arm64: dts: renesas: r8a77990: Fix MSIOF1 DMA channels
arm64: dts: renesas: r8a77990: Add DRIF support
ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add can0 support to camera DB
ARM: dts: r8a7742: Add VSP support
arm64: dts: renesas: Drop superfluous pin configuration containers
arm64: dts: renesas: r8a77961: salvator-xs: Add HDMI Sound support
arm64: dts: renesas: r8a77961: salvator-xs: Add HDMI Display support
arm64: dts: renesas: r8a77961: Add HDMI device nodes
arm64: dts: renesas: r8a77961: Add DU device nodes
arm64: dts: renesas: r8a77961: Add VSP device nodes
arm64: dts: renesas: r8a77961: Add FCP device nodes
arm64: dts: renesas: Fix pin controller node names
ARM: dts: renesas: Fix pin controller node names
arm64: dts: renesas: Add Renesas Falcon boards support
arm64: dts: renesas: Add Renesas R8A779A0 SoC support
ARM: dts: r8a7742-iwg21d-q7: Enable SD2 LED indication
ARM: dts: r8a7742-iwg21d-q7: Add can1 support to carrier board
ARM: dts: r8a7742-iwg21d-q7: Add SPI NOR support
ARM: dts: r8a7742: Add VIN DT nodes
...
Link: https://lore.kernel.org/r/20200918124800.15555-2-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
The Synopsys DesignWare APB GPIO controller driver does not parse
reg-io-width and dtschema does not allow it so drop it to fix dtschema
warnings like:
arch/arm/boot/dts/picoxcell-pc7302-pc3x2.dt.yaml: gpio@20000:
'reg-io-width' does not match any of the regexes: '^gpio-(port|controller)@[0-9a-f]+$', 'pinctrl-[0-9]+'
Link: https://lore.kernel.org/r/20200917164909.22490-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add the s6e63m0 display to the Golden device
- Add the KTD253 backlight to the Skomer device
- Update the LP5521 LED DTS entries for binding changes
-----BEGIN PGP SIGNATURE-----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=jwb5
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.10 kernel cycle:
- Add the s6e63m0 display to the Golden device
- Add the KTD253 backlight to the Skomer device
- Update the LP5521 LED DTS entries for binding changes
* tag 'ux500-dts-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ste-href: Add reg property to the LP5521 channel nodes
ARM: dts: ux500-skomer: Add KTD253 backlight
ARM: dts: ux500-golden: Add S6E63M0 DSI display
Link: https://lore.kernel.org/r/CACRpkda=-cgFjN7K2vBU5x4uSYrohrZSbjqMnSFb3Qe2Az1W5g@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update the SP804 nodes to have the correct clocks and
clock names for the hi3620 SoC
- Update the SP805 nodes to have the correct clocks and
clock names for the hix5hd2 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbPu
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm32-dt-for-5.10' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM: DT: Hisilicon ARM32 SoCs DT updates for 5.10
- Update the SP804 nodes to have the correct clocks and
clock names for the hi3620 SoC
- Update the SP805 nodes to have the correct clocks and
clock names for the hix5hd2 SoC
* tag 'hisi-arm32-dt-for-5.10' of git://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: Fix SP805 clocks
ARM: dts: hisilicon: Fix SP804 users
Link: https://lore.kernel.org/r/5F617209.90003@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct the property for reset GPIOs of the GPIO expander.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PCA9539 GPIO expander requires GPIO controller properties to operate
properly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All am437x boards have been converted to use new driver, so drop legacy
cpsw dt node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch all am437x boards to use new cpsw switch driver. Those boards
have or 2 Ext. port wired and configured in dual_mac mode by default, or
only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT node for the new cpsw switchdev based driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the iWave RZ/G1M schematic, the signal LVDS_PPEN controls the
supply voltage for the touch panel, LVDS receiver and RGB LCD panel. Add
a regulator for these device nodes and remove the powerdown-gpios
property from the lvds-receiver node as it results in a touch controller
driver probe failure.
Fixes: 6f89dd9e93 ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200924080535.3641-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This register describes the silicon id and chip unique id. It varies
between CPU revisions, but is always part of the SCU.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200921091644.133107-4-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
This patch adds FMC2 External Bus Interface support on stm32mp157c.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The "eMMC high-speed DDR mode (3.3V I/O)" at 50MHz is supported on
the eMMC-interface of the lxa-mc1. Set it in the device tree to
benefit from the speed improvement.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The display PWM channel is number 3 (PWM2 CH4), make it so.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH AV96 has RTS/CTS lines available on UART7, describe them in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On the production revision of the SoM, 587-200, the PHY reset GPIO and
touchscreen IRQs are swapped to prevent collision between EXTi IRQs,
reflect that in DT.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Previously the FIFO on the stm32h743 usart was not utilized, because
the stm32f7 compatible configures it without FIFO support.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The stm32 spi driver tries to determine the fifo size of spi devices
dynamically. However, if the spi was already configured by the bootloader
the fifo size check can become an endless loop, because the driver
expects the spi to be in its initial "after device reset" state. The
driver does already support resetting the spi device at probe, thus this
patch adds only the required device tree properties
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH PDK2 has RTS/CTS lines available on UART8, describe them in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The QSPI CS2 is not used on DHCOM, remove the pinmux settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
the desired phase shift between clock- and data-signal, now trigger a
kernel warning when used in rgmii-id mode:
*-skew-ps values should be used only with phy-mode = "rgmii"
This is because commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY") now configures own timings when
phy-mode = "rgmii-id". Device trees wanting to set their own delays
should use phy-mode "rgmii" instead as the warning prescribes.
The "standard" timings now used with "rgmii-id" work fine on this
board, so drop the explicit timings in the device tree and thereby
silence the warning.
Fixes: 666b5ca85c ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH PDK2 board is capable of USB OTG on the X14 USB Mini-AB connector,
fill in the missing bits to make USB OTG possible instead of peripheral.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The AV96 uses sdmmc2_d47_pins_c and sdmmc2_d47_sleep_pins_c, which
differ from sdmmc2_d47_pins_b and sdmmc2_d47_sleep_pins_b in one
pin, SDMMC2_D5, which is PA15 in the former and PA9 in the later.
The PA15 is correct on AV96, so fix this. This error is likely a
result of rebasing across the stm32mp1 DT pinctrl rework.
Fixes: 611325f681 ("ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
Add a Device Tree for the RoseapplePi SBC.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add Device Trees for Caninos Loucos Labrador CoM Core v2 and base board
M v1. Based on the work of Andreas Färber on Lemaker Guitar device tree.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using the native SPI chipselect on i.MX6 is known to be problematic.
Doing it on a imx6q-sabresd causes the SPI NOR probe to fail:
[ 5.388704] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00
Use the GPIO chipselect to avoid such problem.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for imx6q-logicpd.dtb so that it can be built by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is standard practice to have a specific board compatible string, so
pass "logicpd,imx6q-logicpd".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix. While
touching the hogs, fix indentation (spaces -> tabs).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
port6 of mt7530 switch (= cpu port 0) on bananapi-r2 misses pause option
which causes rx drops on running iperf.
Fixes: f4ff257cd1 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200907070517.51715-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The sun8i-codec driver introduced a new set of DAPM widgets that more
accurately describe the hardware topology. Update the various device
trees to use the new widget names.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200726012557.38282-6-samuel@sholland.org
SMB347 is a battery charger controller which is found on the Nexus 7
device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for all MMCs is PLLP, which is running at 408 MHz on
Tegra30 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The default parent for all MMCs is PLLP, which is running at 216 MHz on
Tegra20 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously 50MHz clock rate didn't work because of the wrong PINCTRL
configuration used for SDIO pins. Now the PINCTRL config is corrected
and the MMC clock rate could be bumped safely to 50MHz, increasing WiFi
TX throughput by 20 Mbit/s and allowing to hit the maximum 40 Mbit/s.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The low-power-mode drive was set to DIV_4 for some of PINCTRL groups,
while these groups should use DIV_1. This patch fixes the wrong PINCTRL
configurations and adds a full drive-setup for the changed configs, just
for completeness since the added values match the default configuration.
Now WiFi SDIO communication works properly using legacy signaling mode if
SDIO BUS clocked at 50MHz, which is a maximum SDIO clock rate on Tegra20.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This property was supposed to be upstreamed, but it was NAKed recently
in a favor to a better approach of firmware loading. It also turned
out that the firmware loading isn't really necessary because it's stored
in a non-volatile memory inside of the touchscreen controller and
previously the FW loading was needed in order to get touchscreen working,
but it actually was a TS driver problem which is resolved now. Hence
remove the unsupported property.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MMC core now supports binding to a specific ID, which is very handy for
embedded devices, like Acer A500, because MMC ID may change depending on
kernel version or configuration which affects MMC driver probe order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MMC core now supports binding to a specific ID, which is very handy for
embedded devices, like Nexus 7, because MMC ID may change depending on
kernel version or configuration which affects MMC driver probe order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
"gpios" property is deprecated. Update the Goni DTS to fix
dtbs_checks warnings like:
i2c-pmic: 'sda-gpios' is a required property
i2c-pmic: 'scl-gpios' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-24-krzk@kernel.org
"gpios" property is deprecated. Update the Aquila DTS to fix
dtbs_checks warnings like:
i2c-pmic: 'sda-gpios' is a required property
i2c-pmic: 'scl-gpios' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-23-krzk@kernel.org
The fixed regulators are kept under dedicated "regulators" node but this
causes multiple dtschema warnings:
regulators: $nodename:0: 'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
regulators: #size-cells:0:0: 0 is not one of [1, 2]
regulators: fixed-regulator@0:reg:0: [0] is too short
regulators: fixed-regulator@1:reg:0: [1] is too short
regulators: fixed-regulator@2:reg:0: [2] is too short
regulators: fixed-regulator@3:reg:0: [3] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-22-krzk@kernel.org
The fixed regulators are kept under dedicated "regulators" node but this
causes multiple dtschema warnings:
regulators: $nodename:0: 'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
regulators: #size-cells:0:0: 0 is not one of [1, 2]
regulators: fixed-regulator@0:reg:0: [0] is too short
regulators: fixed-regulator@1:reg:0: [1] is too short
regulators: fixed-regulator@2:reg:0: [2] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-21-krzk@kernel.org
Having the pinctrl-names property in the dtsi leads to dtbs_check warnings
when the board dts doesn't define pinctrl-0. Instead, move the property to
the board dts actually using the mmc node.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200831171129.3886857-5-alexandre.belloni@bootlin.com
We can now pass multiple versions in "opp-supported-hw" property, lets
do that and simplify the tables a bit.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch enables CAN0 interface exposed through connector J4 on the
camera DB.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200911083615.17377-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SP805 DT binding requires two clocks to be specified, but
Hisilicon platform DTs currently only specify one clock.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency.
Since currently both are the very same clock, we can just double the
clock reference, and add the correct clock-names, to match the binding.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The SP804 binding only specifies one or three clocks, but does not allow
just two clocks.
The HiSi 3620 .dtsi specified two clocks for the two timers, plus gave
one "apb_pclk" clock-name to appease the primecell bus driver.
Extend the clocks by duplicating the first clock to the end of the clock
list, and add two dummy clock-names to make the primecell driver happy.
I don't know what the real APB clock for the IP is, but with the current
DT the first timer clock was used for that, so this change keeps the
current status.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
please pull the following:
- Christian adds support for the Cisco Meraki MR32 which is based on the
BCM53016 SoC, this requires specifying the PWM, second UART and third
PCIe controller in Device Tree before finally adding support for the
board.
- Adrian updates the status properties from "ok" to "okay".
- Andre fixes the SP805 watchdog nodes to have the correct clock names
and binding for both the Cygnus and Northstar Plus (NSP). He does the
same thing with the SP804 timer node which was missing an
"arm,primecell" compatible string.
- Maxime enables the BCM2711 (Raspberry Pi 4) display pipeline since all
DRM changes are ready.
-----BEGIN PGP SIGNATURE-----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=EBR/
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.10/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs changes for 5.10,
please pull the following:
- Christian adds support for the Cisco Meraki MR32 which is based on the
BCM53016 SoC, this requires specifying the PWM, second UART and third
PCIe controller in Device Tree before finally adding support for the
board.
- Adrian updates the status properties from "ok" to "okay".
- Andre fixes the SP805 watchdog nodes to have the correct clock names
and binding for both the Cygnus and Northstar Plus (NSP). He does the
same thing with the SP804 timer node which was missing an
"arm,primecell" compatible string.
- Maxime enables the BCM2711 (Raspberry Pi 4) display pipeline since all
DRM changes are ready.
* tag 'arm-soc/for-5.10/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: broadcom: Fix SP804 node
ARM: dts: NSP: Fix SP805 clock-names
ARM: dts: Cygnus: Fix SP805 clocks
ARM: dts: NSP: replace status value "ok" by "okay"
ARM: BCM5301X: Add DT for Meraki MR32
ARM: dts: bcm2711: Enable the display pipeline
ARM: dts: BCM5301X: Specify pcie2 in the DT
ARM: dts: BCM5301X: Specify uart2 in the DT
ARM: dts: BCM5301X: Specify PWM in the DT
dt-bindings: ARM: add bindings for the Meraki MR32
Link: https://lore.kernel.org/r/20200912032153.1216354-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- New machines
* Wistron Mowgli, an AST2500 BMC for a Power9 OpenPower server
* Facebook Wedge400, an AST2500 BMC system which we can assume is 4
times better than the existing Wedge100 top of rack network switch
- Add a new device, the IBM Operation Panel
- Fixes for Facebook's collection of BMCs
- eMMC and vuart fixes
-----BEGIN PGP SIGNATURE-----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=C32V
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.10-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.10
- New machines
* Wistron Mowgli, an AST2500 BMC for a Power9 OpenPower server
* Facebook Wedge400, an AST2500 BMC system which we can assume is 4
times better than the existing Wedge100 top of rack network switch
- Add a new device, the IBM Operation Panel
- Fixes for Facebook's collection of BMCs
- eMMC and vuart fixes
* tag 'aspeed-5.10-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add Mowgli BMC platform
ARM: dts: rainier: Disable internal pull-downs on eMMC pins
ARM: aspeed: g5: Do not set sirq polarity
ARM: dts: aspeed: rainier: Add IBM Operation Panel I2C device
ARM: dts: aspeed: tacoma: Add IBM Operation Panel I2C device
ARM: dts: aspeed: rainier: Enable XDMA engine
ARM: dts: aspeed: wedge40: Update UART4 pin settings
ARM: dts: aspeed: wedge40: Update FMC flash0 label
ARM: dts: aspeed: Add Facebook Wedge400 BMC
ARM: dts: aspeed: minipack: Update 64MB FMC flash layout
ARM: dts: aspeed: yamp: Set 32MB FMC flash layout
ARM: dts: aspeed: cmm: Set 32MB FMC flash layout
ARM: dts: aspeed: Remove flash layout from Facebook AST2500 Common dtsi
Link: https://lore.kernel.org/r/CACPK8XcDNBYAHzW6NYB4LFm3YbN63AprgW75ZqS+6uXn2b3kug@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
A few device tree source fixes to make them fully SP804 timer and
SP805 watchdog binding compliant.
-----BEGIN PGP SIGNATURE-----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=93Pt
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/Vexpress/Fast Models updates for v5.10
A few device tree source fixes to make them fully SP804 timer and
SP805 watchdog binding compliant.
* tag 'juno-updates-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: arm: Fix SP805 clock-names
ARM: dts: arm: Fix SP805 clocks
ARM: dts: arm: Fix SP804 users
Link: https://lore.kernel.org/r/20200908135028.GA10106@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add sound support to Galaxy S3/Midas family (Exynos4412).
2. Add sound support to Galaxy S/Aries family (S5Pv210).
3. Configure L2C-310 cache controller via DTS on Exynos4.
4. Big cleanup of Exynos DTS to fix as many dtschema warnings as
possible. This includes adding missing properties (thus e.g.
enabling S3C RTC clock), correcting existing nodes, renaming of
nodes and using non-deprecated properties or compatibles. Except
mentioned bring up of S3C RTC, this should not have visible
effect.
-----BEGIN PGP SIGNATURE-----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=V1Fr
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.10
1. Add sound support to Galaxy S3/Midas family (Exynos4412).
2. Add sound support to Galaxy S/Aries family (S5Pv210).
3. Configure L2C-310 cache controller via DTS on Exynos4.
4. Big cleanup of Exynos DTS to fix as many dtschema warnings as
possible. This includes adding missing properties (thus e.g.
enabling S3C RTC clock), correcting existing nodes, renaming of
nodes and using non-deprecated properties or compatibles. Except
mentioned bring up of S3C RTC, this should not have visible
effect.
* tag 'samsung-dt-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (49 commits)
ARM: dts: exynos: Silence SATA PHY warning in Exynos5250
ARM: dts: exynos: Remove I2C9 samsung, i2c-slave-addr from Exynos5250 boards
ARM: dts: samsung: odroid-xu3: Move assigned-clock* properties to i2s0 node
ARM: dts: exynos: Use S2MPS11 clock in S3C RTC in SMDK5420
ARM: dts: exynos: Silence DP HPD pinctrl dtschema warning in Exynos5250 Spring
ARM: dts: exynos: Use S5M8767 clock in S3C RTC in Exynos5250 Spring
ARM: dts: exynos: Add max77686 clocks for S3C RTC in SMDK5250
ARM: dts: exynos: Override thermal by label in Exynos5250
ARM: dts: exynos: Correct whitespace and indentation issues in Exynos5
ARM: dts: exynos: Silence i2c-gpio dtschema warning in Exynos5250 Arndale
ARM: dts: exynos: Correct S3C RTC bindings in SMDK5410
ARM: dts: exynos: Remove unneeded address/size cells in Exynos5260 GIC
ARM: dts: exynos: Correct compatible for Exynos5260 GIC
ARM: dts: exynos: Correct compatible for Exynos5 GIC
ARM: dts: s5pv210: Enable audio on Aries boards
ARM: dts: exynos: Correct whitespace and indentation issues
ARM: dts: exynos: Correct S3C RTC bindings in Tiny4412
ARM: dts: exynos: Correct S3C RTC bindings in SMDK4412
ARM: dts: exynos: Add CPU cooling in Tiny4412
ARM: dts: exynos: Add CPU cooling in SMDK4412
...
Link: https://lore.kernel.org/r/20200907150425.11077-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
- Increase support for the RZ/G2H SoC on the HopeRun HiHope RZ/G2H
board, and its display panel expansion board,
- Increase support for the RZ/G1H SoC on the iWave RainboW SoM (G21M)
and Qseven board (G21D),
- SATA support for the HopeRun HiHope RZ/G2N board,
- PCIe endpoint support for the RZ/G2M, RZ/G2E, and RZ/G2H SoCs,
- Audio support for the R-Car M3-W+ SoC.
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX1IGJwAKCRCKwlD9ZEnx
cKjGAPkB8Jcd9TsR5PGsuZ829aTqVVKZqh3A3rOwWZ3rsRwD3AD8DYKVolrsTA0d
VbbGki8kpE8uihvqS/9xSHnfLiC7jQ8=
=iYmH
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.10
- Increase support for the RZ/G2H SoC on the HopeRun HiHope RZ/G2H
board, and its display panel expansion board,
- Increase support for the RZ/G1H SoC on the iWave RainboW SoM (G21M)
and Qseven board (G21D),
- SATA support for the HopeRun HiHope RZ/G2N board,
- PCIe endpoint support for the RZ/G2M, RZ/G2E, and RZ/G2H SoCs,
- Audio support for the R-Car M3-W+ SoC.
- Minor fixes and improvements.
* tag 'renesas-arm-dt-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (39 commits)
arm64: dts: renesas: Add HiHope RZ/G2H board with idk-1110wr display
arm64: dts: renesas: r8a774e1: Add cpuidle support for CA5x cores
arm64: dts: renesas: r8a774e1: Add FDP1 device nodes
ARM: dts: r8a7742-iwg21d-q7: Enable PCIe Controller
ARM: dts: r8a7742: Add IPMMU DT nodes
arm64: dts: renesas: r8a77961: Enable Sound / Audio-DMAC
arm64: dts: renesas: r8a774e1: Add PWM device nodes
ARM: dts: r8a7742-iwg21m: Add SPI NOR support
arm64: dts: renesas: r8a774e1-hihope-rzg2h: Enable HS400 mode
ARM: dts: r8a7742-iwg21m: Add RTC support
ARM: dts: r8a7742-iwg21m: Sort the nodes alphabetically
ARM: dts: r8a7742: Add CAN support
arm64: dts: renesas: r8a774c0: Add PCIe EP node
arm64: dts: renesas: r8a774b1: Add PCIe EP nodes
arm64: dts: renesas: r8a774a1: Add PCIe EP nodes
ARM: dts: r8a7742: Add QSPI support
arm64: dts: renesas: r8a774e1-hihope-rzg2h: Setup DU clocks
arm64: dts: renesas: r8a774e1: Add LVDS device node
arm64: dts: renesas: r8a774e1: Populate HDMI encoder node
arm64: dts: renesas: r8a774e1: Populate DU device node
...
Link: https://lore.kernel.org/r/20200904114819.30254-3-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
5.9, please pull the following:
- Florian fixes the Broadcom QSPI controller binding such that the most
specific compatible string is the left most one, and all existing
in-tree users are updated as well.
-----BEGIN PGP SIGNATURE-----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=a2Q2
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.9/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.9, please pull the following:
- Florian fixes the Broadcom QSPI controller binding such that the most
specific compatible string is the left most one, and all existing
in-tree users are updated as well.
* tag 'arm-soc/for-5.9/devicetree-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
Link: https://lore.kernel.org/r/20200909211857.4144718-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix the misspelling of 'interrupts' property in i.MX8MQ TMU DT node.
- Correct 'ahb' clock for i.MX8MP SDMA1 in device tree.
- Fix pad QSPI1B_SCLK mux mode for UART3 on i.MX6SX.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl9Y6BsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6xVggApTBRKs67uPBYQFPRpsPEnXmRuyD+
zDxLjyf5WKh71gP3zDPzMj2TTdz1tE0H4sGwLe5VDAfkhCSQxOtMpfDY22Ateq/O
DDwiN9DGslutyPy/a4pkysvwaJWJRJD1e1PsdX5fIB1gO8VUHW5qB066ADpXFhRv
t/yUUkBQGTxaBHaNkzhdWLiCgVVGkJGueCEp/A2Yg7nK38ibCQ6WdD1tcu+VQpxZ
bc9zo7ue2ZNYtMDSkc9OZgp7o7rK+J3LmjZMBOuIQS6VA4nh+6uTh3kpLXGGkhy6
FA8ZxXYv4qt1t6F9tuSP0XV0em9jkEUOvFT8ms0uVBi4fk7K5HvDaPFWPg==
=CYG2
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.9, round 2:
- Fix the misspelling of 'interrupts' property in i.MX8MQ TMU DT node.
- Correct 'ahb' clock for i.MX8MP SDMA1 in device tree.
- Fix pad QSPI1B_SCLK mux mode for UART3 on i.MX6SX.
* tag 'imx-fixes-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
Link: https://lore.kernel.org/r/20200909143844.GA25109@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Few fixes for omap based devices:
- Fix of_clk_get() error handling for omap-iommu
- Fix missing audio pinctrl entries for logicpd boards
- Fix video for logicpd-som-lv after switch to generic panels
- Fix omap5 DSI clocks base
-----BEGIN PGP SIGNATURE-----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=K8IT
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.9-rc cycle
Few fixes for omap based devices:
- Fix of_clk_get() error handling for omap-iommu
- Fix missing audio pinctrl entries for logicpd boards
- Fix video for logicpd-som-lv after switch to generic panels
- Fix omap5 DSI clocks base
* tag 'omap-for-v5.9/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Fix DSI base address and clocks
ARM: dts: logicpd-som-lv-baseboard: Fix missing video
ARM: dts: logicpd-som-lv-baseboard: Fix broken audio
ARM: dts: logicpd-torpedo-baseboard: Fix broken audio
ARM: OMAP2+: Fix an IS_ERR() vs NULL check in _get_pwrdm()
Link: https://lore.kernel.org/r/pull-1599132064-54898@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Specify the National LM75 sensor including its vendor name, as mandated
by the binding docs.
Fixes: cac849e9bb ("ARM: dts: imx6qdl: add TQMa6{S,Q,QP} SoM")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This property is unneeded and not supported by the spi-imx driver.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PMIC configuration is indented one level too deep.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
gic@fb001000: $nodename:0:
'gic@fb001000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix dtschema validator warnings like:
l2-cache-controller@c00000: $nodename:0:
'l2-cache-controller@c00000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Fix dtschema validator warnings like:
l2-cache-controller@20100000: $nodename:0:
'l2-cache-controller@20100000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Mans Rullgard <mans@mansr.com>
Fix dtschema validator warnings like:
l2-cache: $nodename:0: 'l2-cache' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Fix dtschema validator warnings like:
l2-cache@2040000: $nodename:0:
'l2-cache@2040000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix dtschema validator warnings like:
l2-cache-controller@80040000: $nodename:0:
'l2-cache-controller@80040000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Barry Song <baohua@kernel.org>
The purpose of those assigned-clock-* properties is to configure clock for
the I2S device so move them to respective node. This silences the
dtschema warnings like:
'clocks' is a dependency of 'assigned-clocks'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200906142146.21266-3-krzk@kernel.org
Commit 6860510146 ("ARM: dts: exynos: Add support for audio over HDMI
for Odroid X/X2/U3") added assigned clocks under Clock Management Unit.
However the dtschema expects "clocks" property if "assigned-clocks" are
used. Add reference to input clock to silence the dtschema warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dt.yaml: clock-controller@10030000: 'clocks' is a dependency of 'assigned-clocks'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200906142146.21266-2-krzk@kernel.org
Commit 52005dece5 ("ARM: dts: Add assigned clock parents to CMU node
for exynos3250") added assigned clocks under Clock Management Unit to
fix hangs when accessing ISP registers.
However the dtschema expects "clocks" property if "assigned-clocks" are
used. Add reference to input clock to silence the dtschema warnings:
arch/arm/boot/dts/exynos3250-artik5-eval.dt.yaml: clock-controller@10030000: 'clocks' is a dependency of 'assigned-clocks'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200906142146.21266-1-krzk@kernel.org
The fixed clocks are kept under dedicated 'clocks' node but this causes
multiple dtschema warnings:
clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
clocks: #size-cells:0:0: 0 is not one of [1, 2]
clocks: xti@0:reg:0: [0] is too short
clocks: 'ranges' is a required property
xti@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-12-krzk@kernel.org
The CPU nodes should be described as children of "cpus" bus node with
appropriate "reg" properties:
cpus: '#address-cells' is a required property
cpus: '#size-cells' is a required property
cpu: 'device_type' is a required property
cpu: 'reg' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-11-krzk@kernel.org
Although PWM is used on S3C24xx as clocksource/timer, the dtschema
expects the node to be named in certain format:
timer@51000000: $nodename:0: 'timer@51000000' does not match '^pwm(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-10-krzk@kernel.org
Using full paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-9-krzk@kernel.org
Only the specific compatible (arm,arm1176jzf-s) is allowed by dtschema:
cpu@0: compatible: ['arm,arm1176jzf-s', 'arm,arm1176'] is too long
cpu@0: compatible: Additional items are not allowed ('arm,arm1176' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-7-krzk@kernel.org
The SROM controller is modeled with a bus so align the device node name
with dtschema to fix warning:
srom-cs1@18000000: $nodename:0: 'srom-cs1@18000000'
does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-6-krzk@kernel.org
The SROM controller is modeled with a bus so align the device node name
with dtschema to fix warning:
srom-cs1@18000000: $nodename:0: 'srom-cs1@18000000'
does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-5-krzk@kernel.org
The fixed clocks are kept under dedicated 'clocks' node but this causes
multiple dtschema warnings:
clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
clocks: #size-cells:0:0: 0 is not one of [1, 2]
clocks: oscillator@0:reg:0: [0] is too short
clocks: oscillator@1:reg:0: [1] is too short
clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-4-krzk@kernel.org
The fixed clocks are kept under dedicated 'clocks' node but this causes
multiple dtschema warnings:
clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
clocks: #size-cells:0:0: 0 is not one of [1, 2]
clocks: oscillator@0:reg:0: [0] is too short
clocks: oscillator@1:reg:0: [1] is too short
clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-3-krzk@kernel.org
The SROM bank 5 is at address 0xa8000000, just like the one put in "reg"
property of ethernet node. Fix the unit address of ethernet node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907183313.29234-2-krzk@kernel.org
According to Devicetree Specification v0.2 and later, Section "Generic
Names Recommendation", the node name for a pin controller device node
should be "pinctrl".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200821112351.5518-1-geert+renesas@glider.be
The Mowgli BMC is an ASPEED ast2500 based BMC that is part of an
OpenPower Power9 server.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909090818.24021-1-ben_pai@wistron.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The DT binding for SP804 requires to have an "arm,primecell" compatible
string.
Add this string so that the Linux primecell bus driver picks the device
up and activates the clock.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
[florian: added compatible to ccbtimer1]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SP805 binding sets the name for the actual watchdog clock to
"wdog_clk" (with an underscore).
Change the name in the DTs for the Broadcom NSP platform to match that.
The Linux and U-Boot driver use the *first* clock for this purpose
anyway, so it does not break anything.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The SP805 DT binding requires two clocks to be specified, but the
Broadcom Cygnus DT currently only specifies one clock.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency.
Since currently both are the very same clock, we can just double the
clock reference, and add the correct clock-names, to match the binding.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
add support for the Cisco Meraki MR32.
This is a dual-band enterprise class 802.11ac access point.
The unit was donated by Chris Blake. Thank you!
SoC: Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM: 128 MiB
NAND: 128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH: 1GBit Ethernet Port - PoE
WIFI1: Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2: Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3: Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BLE: Broadcom BCM20732 (ttyS1)
LEDS: 1 x Programmable RGB Status LED (driven by a PWM)
1 x White LED (GPIO)
1 x Orange LED Fault Indicator (GPIO)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC)
ina219 hardware monitor (i2c)
Kensington Lock
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC, RX, TX, GND.
Odd stuff:
- uart0 clock frequency is 62.5 MHz.
- The LEDs are labeled as SYS-LED1 through SYS-LED3
because of the silkscreen on the PCB.
- the original u-boot has been compiled with most functions
and commands disabled. The u-boot env isn't setup properly
either and as a result, the bcm47xxpart probing is not
working. Hence, the nand partitions are specified through a
"fixed-partition" binding.
- The "WICED SMART(TM)" Bluetooth LE 4.0 BCM20732 chip is
connected to uart2 of the SoC. The BCM20732 does not
provide a HCI. So the linux' bluetooth stack is useless.
The mock-up node with the compatible binding and
enable-gpios property is provided solely as documentation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode
property should be specified on port nodes. However, the microchip
drivers read it from the switch node.
Let the driver use the per-port property and fall back to the old
location with a warning.
Fix in-tree users.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SPI NOR device which is connected to MSIOF0 interface
on the iWave RainboW-G21d-q7 board.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200907155541.2011-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All dra7/am57 boards converted to use new driver, so drop legacy
cpsw dt node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch CompuLab CL-SOM-AM57x board to use new cpsw switch driver. Those
board configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all TI DRA7x boards to use new cpsw switch driver. Those boards
configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all TI AM5728 BeagleBoard-X15 boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch all am571/2/4-idk boards to use new cpsw switch driver.
Those boards have 2 Ext. port wired and configured in dual_mac mode by
default. Hence, dual_mac mode has been preserved the same way between
legacy and new driver it's safe to switch drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch BeagleBone AI to use new cpsw switch driver.
It has one Ext. port only and fits dual_mac mode with no issues.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove nokia,nvm-size property as it is no longer needed. The driver can
nowadays figure out the size so do not specify it in DT.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 1c8f406507 ("ARM: dts: BCM5301X: convert to iProc QSPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 329f98c197 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
spi-gpio-0: $nodename:0: 'spi-gpio-0' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-25-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-16-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-15-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-14-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-13-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-12-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-11-krzk@kernel.org
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org
The fixed clocks are kept under dedicated 'external-clocks' node, thus a
fake 'reg' was added. This is not correct with dtschema as fixed-clock
binding does not have a 'reg' property. Moving fixed clocks out of
'soc' to root node fixes multiple dtbs_check warnings:
external-clocks: $nodename:0: 'external-clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
external-clocks: #size-cells:0:0: 0 is not one of [1, 2]
external-clocks: oscillator@0:reg:0: [0] is too short
external-clocks: oscillator@1:reg:0: [1] is too short
external-clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-7-krzk@kernel.org
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-6-krzk@kernel.org
Fix typo in pinctrl property of "vibrator-en" fixed regulator in Aries
family of boards. The error caused lack of pin configuration for the
GPIO used in vibrator.
Fixes: 04568cb58a ("ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-5-krzk@kernel.org
GPU needs additional regulator, add it to devicetree of bpi-r2
Signed-off-by: Alex Ryabchenko <d3adme4t@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200904110002.88966-5-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
mt7623a has no graphics support so move nodes from generic mt7623.dtsi
to mt7623n.dtsi
Fixes: 1f6ed22459 ("arm: dts: mt7623: add Mali-450 device node")
Suggested-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20200904110002.88966-3-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
A feature was added to the aspeed vuart driver to configure the vuart
interrupt (sirq) polarity according to the LPC/eSPI strapping register.
Systems that depend on a active low behaviour (sirq_polarity set to 0)
such as OpenPower boxes also use LPC, so this relationship does not
hold. Jeremy confirms that the s2600st which is strapped for eSPI also
does not have this relationship.
The property was added for a Tyan S7106 system which is not supported
in the kernel tree. Should this or other systems wish to use this
feature of the driver they should add it to the machine specific device
tree.
Fixes: c791fc76bc ("arm: dts: aspeed: Add vuart aspeed,sirq-polarity-sense...")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jeremy Kerr <jk@ozlabs.org>
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200812112400.2406734-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 7 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-6-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 0 to multi-master mode and add the panel device that will
register as a slave.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200908200101.64974-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Now that all the drivers have been adjusted for it, let's bring in the
necessary device tree changes.
The VEC and PV3 are left out for now, since it will require a more specific
clock setup.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/cfce2276d172d3d9c4d34d966b58fd47f77c4e46.1599120059.git-series.maxime@cerno.tech
Add the reg property to each channel node. This update is
to accommodate the multicolor framework. In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200812195020.13568-7-dmurphy@ti.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SP805 binding sets the name for the actual watchdog clock to
"wdog_clk" (with an underscore).
Change the name in the DTs for ARM Ltd. platforms to match that. The
Linux and U-Boot driver use the *first* clock for this purpose anyway,
so it does not break anything.
For MPS2 we only specify one clock so far, but the binding requires
two clocks to be named.
In practice, Linux would pick a clock named "apb_pclk" for the bus
clock, and the Linux and U-Boot SP805 driver would use the first clock
to derive the actual watchdog counter frequency. So since currently both
are the very same clock, we can just double the clock reference, and add
the correct clock-names, to match the binding.
Link: https://lore.kernel.org/r/20200828130602.42203-8-andre.przywara@arm.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SP804 DT nodes for Realview, MPS2 and VExpress were not complying
with the binding: it requires either one or three clocks, but does not
allow exactly two clocks.
Simply duplicate the first clock to satisfy the binding requirement.
For MPS2, we triple the clock, and add the clock-names property, as this
is required by the Linux primecell driver.
Try to make the clock-names more consistent on the way.
Link: https://lore.kernel.org/r/20200828142018.43298-3-andre.przywara@arm.com
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The SATA PHY in Exynos5250 SoCs has two interfaces and two device nodes:
1. sata-phy@12170000
2. i2c-9/i2c@38
The first node represents the actual SATA PHY device with phy-cells.
The second represents an additional I2C interface, needed by the driver
to communicate with the SATA PHY device. It is not a PHY-provider in
the terms of dtschema so rename it to silence dtbs_check warning:
arch/arm/boot/dts/exynos5250-arndale.dt.yaml: sata-phy@38: '#phy-cells' is a required property
From schema: lib/python3.6/site-packages/dtschema/schemas/phy/phy-provider.yaml
This second device node is also a property of SoC, not a board so move
it there.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902155733.20271-2-krzk@kernel.org
The property samsung,i2c-slave-addr in I2C9 controller on Exynos5250
Arndale and SMDK5250 boards, is not actually needed. There is only one
master on this bus. It's not clear why this property was added at first
place.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200902155733.20271-1-krzk@kernel.org
The purpose of those assigned-clock-* properties is to configure clock for
for the I2S device so move them to respective node.
This suppresses the dtbs_check warning:
arch/arm/boot/dts/exynos5422-odroidxu3.dt.yaml: sound: 'clocks' is a dependency of 'assigned-clocks'
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Device tree schema expects NAND controller to be named
"nand-controller", otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dt.yaml: gpmi-nand@8000c000:
$nodename:0: 'gpmi-nand@8000c000' does not match '^nand-controller(@.*)?'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Like the other i-MX devices the i.MX6 family can output the enet tx
clock on the pad to feed the connected device. Add the missing clk here
to avoid local fixups like: arch/arm/boot/dts/imx6qdl-tx6.dtsi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The common imx6qdl.dtsi already defines the iomuxc phandle. Make use of
it in the imx6dl.dtsi and imx6q.dtsi.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pad QSPI1B_SCLK mux mode 0x1 is for function UART3_DTE_TX,
correct the mux mode.
Fixes: 743636f25f ("ARM: dts: imx: add pin function header for imx6sx")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Tolino Shine 2 HD Ebook reader. It is based
on boards marked with "37NB-E60QF0+4A2". It is equipped with an i.MX6SL
SoC.
Expected to work:
- Buttons
- Wifi
- Touchscreen
- LED
- uSD
- USB
- RTC
Not working due to missing drivers:
- Backlight (requires NTXEC driver)
- EPD
Not working due to unknown reasons:
- deep sleep (echo standby >/sys/power/state works),
wakeup fails when imx_gpc_pre_suspend(true) was called.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the five IPMMU instances found in the r8a7742 to DT with a disabled
status.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200825141805.27105-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use the 32 kHz clock from S2MPS11 PMIC in the S3C RTC node. Except
making the S3C RTC working, this also fixes dtbs_check warnings:
arch/arm/boot/dts/exynos5420-smdk5420.dt.yaml: rtc@101e0000: clocks: [[2, 317]] is too short
arch/arm/boot/dts/exynos5420-smdk5420.dt.yaml: rtc@101e0000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-14-krzk@kernel.org
Add the five IPMMU instances found in the r8a7742 to DT with a disabled
status.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200825141805.27105-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pin configuration of Display Port HPD GPIO emds with '-gpio' which
confuses dtschema:
arch/arm/boot/dts/exynos5250-spring.dt.yaml: pinctrl@11400000: dp-hpd-gpio:
{'samsung,pins': ['gpc3-0'], ... 'samsung,pin-drv': [[0]], 'phandle': [[23]]} is not of type 'array'
From schema: lib/python3.6/site-packages/dtschema/schemas/gpio/gpio-consumer.yaml
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-11-krzk@kernel.org
Use the 32 kHz clock from S5M8767 PMIC in the S3C RTC node. Except
making the S3C RTC working, this also fixes dtbs_check warnings:
arch/arm/boot/dts/exynos5250-spring.dt.yaml: rtc@101e0000: clocks: [[2, 337]] is too short
arch/arm/boot/dts/exynos5250-spring.dt.yaml: rtc@101e0000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-10-krzk@kernel.org
Add clock-cells to max77686 PMIC node so its 32 kHz clocks could be used
later in the S3C RTC node. Except making the S3C RTC working, this also
fixes dtbs_check warnings:
arch/arm/boot/dts/exynos5250-smdk5250.dt.yaml: rtc@101e0000: clocks: [[2, 337]] is too short
arch/arm/boot/dts/exynos5250-smdk5250.dt.yaml: rtc@101e0000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-9-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-8-krzk@kernel.org
The name of I2C controller over GPIO lines node ends with '-gpio' which
confuses dtschema:
arch/arm/boot/dts/exynos5250-arndale.dt.yaml: soc: i2c-gpio:
{'pinctrl-names': ['default'], ... 'phandle': [[65]]} is not of type 'array'
From schema: lib/python3.6/site-packages/dtschema/schemas/gpio/gpio-consumer.yaml
Add a '-10' (there are already 0-9 I2C controllers on the SoC) suffix to
silence it. This pattern on naming i2c-gpio is already present in many
other dts. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-6-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add
a workaround to model its clock with a fixed-clock. This fixes S3C RTC
and silences dtbs_check warnings like:
arch/arm/boot/dts/exynos5410-smdk5410.dt.yaml: rtc@101e0000: clocks: [[5, 317]] is too short
arch/arm/boot/dts/exynos5410-smdk5410.dt.yaml: rtc@101e0000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-5-krzk@kernel.org
The Exynos5260 GIC node does not have any children so remove the address
and size cells as they are not needed by DT bindings. The size-cells of
'0' were also incorrect. This fixes dtbs_check warning:
arch/arm/boot/dts/exynos5260-xyref5260.dt.yaml: interrupt-controller@10481000: #size-cells:0:0: 1 was expected
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-4-krzk@kernel.org
Exynos5260 SoCs have ARM GIC 400. Correct the compatibles to match
dtschema and fix the dtbs_check warnings like:
arch/arm/boot/dts/exynos5260-xyref5260.dt.yaml: interrupt-controller@10481000:
compatible: ['arm,cortex-a15-gic', 'arm,cortex-a9-gic'] is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-3-krzk@kernel.org
Exynos5250 and Exynso54xx SoCs have ARM GIC 400. Correct the
compatibles to match dtschema and fix the dtbs_check warnings like:
arch/arm/boot/dts/exynos5420-peach-pit.dt.yaml: interrupt-controller@10481000:
compatible: ['arm,gic-400', 'arm,cortex-a15-gic', 'arm,cortex-a9-gic']
is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-2-krzk@kernel.org
The reg property is mandatory for cpu nodes, also fix the #address-cells of
the cpus node that has to be at least 1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200831171129.3886857-2-alexandre.belloni@bootlin.com
Both the Galaxy S and the Fascinate4G have a WM8994 codec, but they
differ slightly in their jack detection and micbias configuration.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add a
workaround to model its clock with fixed-clock. This fixes S3C RTC and
silences dtbs_check warnings like:
arch/arm/boot/dts/exynos4412-tiny4412.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-tiny4412.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-32-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add a
workaround to model its clock with fixed-clock and silence dtbs_check
warnings like:
arch/arm/boot/dts/exynos4412-smdk4412.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-smdk4412.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-31-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 Tiny4412
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-30-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 SMDK4412
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-29-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 Origen
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-28-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-27-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-26-krzk@kernel.org
Add node for clock controller of Samsung S5M8767 PMIC. This provides
the 32768 Hz clock required by S3C RTC. Except making the S3C RTC
working, this also fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4412-origen.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-origen.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-25-krzk@kernel.org
The fixed clocks implemented by Samsung clock drivers use only one
compatible so drop the additional "fixed-clock" to fix dtbs_check
warnings like:
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible:0: 'fixed-clock' was expected
From schema: Documentation/devicetree/bindings/clock/fixed-clock.yaml
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible: ['samsung,clock-xxti', 'fixed-clock'] is too long
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible: Additional items are not allowed ('fixed-clock' was unexpected)
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: '#clock-cells' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-24-krzk@kernel.org
Align the name of mag-mhl-gpio node to avoid dtschema confusion and
dtbs_check warning:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: pinctrl@11000000: mag-mhl-gpio:
{'samsung,pins': ['gpd0-2'], 'samsung,pin-function': [[3]], 'samsung,pin-pud': [[0]]} is not of type 'array'
From schema: dtschema/schemas/gpio/gpio-consumer.yaml
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-22-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210
Universal C310 board. This allows to scale down CPU frequency (and
voltage) in case of thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-21-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210 SMDKv310
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-20-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210 Origen
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-19-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-18-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-17-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-16-krzk@kernel.org
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: spi-lcd:
$nodename:0: 'spi-lcd' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-15-krzk@kernel.org
"gpio-sck" and "gpio-mosi" are deprecated so update the DTS to fix
dtbs_checks warnings like:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: spi-lcd:
gpio-sck: False schema does not allow [[85, 1, 0]]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-14-krzk@kernel.org
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: spi-lcd:
$nodename:0: 'spi-lcd' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-13-krzk@kernel.org
The PMIC has a 32768 Hz clock used by the modem which is implemented by
driver as a regulator. Add and enable it to be sure modem get's its
signal.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-10-krzk@kernel.org
The PMIC has a 32768 Hz clock used by the modem which is implemented by
driver as a regulator. Add and enable it to be sure modem get's its
signal.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-8-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no clock provided for the PMIC and the driver registers
the clock as regulator. This is an old driver which will not be updated
so add a workaround - a fixed-clock to fill missing clock phandle
reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-smdkv310.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-smdkv310.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-7-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no clock provided for the PMIC and the driver registers
the clock as regulator. This is an old driver which will not be updated
so add a workaround - add a fixed-clock to fill missing clock phandle
reference in S3C RTC. The "clock" regulator in PMIC is already present
and enabled.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-6-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-trats.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-trats.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-5-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-origen.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-origen.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-4-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-3-krzk@kernel.org
The regulator property 'regulator-microvolt-offset' should be put next
to regulator definition, not consumer.
The property 'regulator-microsecs-delay' is not valid at all.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-2-krzk@kernel.org
The name of I2C controller over GPIO lines node ends with '-gpio' which
confuses dtschema:
/arch/arm/boot/dts/exynos4210-i9100.dt.yaml: /: i2c-gpio:
{'compatible': ['i2c-gpio'], ... 'maxim,over-volt': [[4500]]}} is not of type 'array'
From schema: lib/python3.6/site-packages/dtschema/schemas/gpio/gpio-consumer.yaml
Add a '-0' suffix to silence it. This pattern on naming i2c-gpio is
already present in many other dts. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-1-krzk@kernel.org
The binding for DesignWare HS OTG USB 2.0 in Samsung SoCs take only one
compatible. This fixes dtbs_check warnings like:
arch/arm/boot/dts/exynos3250-artik5-eval.dt.yaml: hsotg@12480000:
compatible: ['samsung,s3c6400-hsotg', 'snps,dwc2'] is not valid under any of the given schemas (Possible causes of the failure):
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200829172532.29358-4-krzk@kernel.org
The fixed clocks are kept under dedicated node fixed-rate-clocks, thus a
fake "reg" was added. This is not correct with dtschema as fixed-clock
binding does not have a "reg" property:
arch/arm/boot/dts/exynos3250-artik5-eval.dt.yaml: clock@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200829172532.29358-2-krzk@kernel.org
Add support for the SPI NOR device used to boot up the system
to the System on Module DT.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200825085435.8744-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6qdl-gw553x.dtsi:65.12-110.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unneeded #address-cells/#size-cells properties to fix the issue.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Link: https://lore.kernel.org/r/20200830190820.20583-1-freifunk@adrianschmutzler.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The use of cpu0-supply for cpu0 alone is deprecated,
so add cpu-supply to each cpu separately and
update all existing rk3066a boards.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200813172451.13754-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The use of cpu0-supply for cpu0 alone is deprecated,
so add cpu-supply to each cpu separately and
update all existing rk3288 boards that use this property.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200813180241.14660-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The property "fsl,spi-num-chipselects" is gone since commit 790739c441
("dt-bindings: spi: Convert imx cspi to json-schema").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoC supports three pcie ports. Currently, only
pcie0 and pcie1 are enabled. This patch adds the
pcie2 port as well.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BCM53016 in the Meraki MR32 utilizes the third "uart2"
to connect to a on-board Bluetooth-LE 4.0 BCM20732 chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BCM53016 in the Meraki MR32 uses the on-chip PWM
controller to drive a tri-color RGB LED. Since I plan
to use the PWM, I made a label for the pwm's pinmux
node. This way, it can be easily referenced.... And
Also included a label for the i2c since I'm going to
need it in the future too.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds support for the GARDENA smart Gateway, which is based on
the Atmel AT91SAM9G25. It is equipped with 128 MiB of DDR2 RAM and
256 MiB NAND storage.
Please note that this gateway is not actually based on a AT91SAM9x5 EK
board, but is close enough to allow its DT to be used.
Co-developed-by: Stefan Roese <sr@denx.de>
Co-developed-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200822151023.31629-2-code@reto-schneider.ch
Enable BQ32000 RTC which is connected to I2C0 on the iWave RainboW-G21M-q7
SOM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200816193316.7641-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200824193649.978197-1-jernej.skrabec@siol.net
Fix the VGA reserved memory node, and add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Wedge400 (AST2500) BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200824211948.12852-6-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 64Mb FMC flash layout in Minipack device tree explicitly because the
flash layout was removed from "ast2500-facebook-netbmc-common.dtsi".
Please note "data0" partition' size is updated to 4MB to be consistent
with other Facebook OpenBMC platforms.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 32MB FMC flash layout in Yamp device tree explicitly because flash
layout settings were removed from "ast2500-facebook-netbmc-common.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 32MB FMC flash layout in CMM device tree explicitly because the flash
layout settings were removed from "ast2500-facebook-netbmc-common.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Remove FMC flash layout from ast2500-facebook-netbmc-common.dtsi because
flash size and layout varies across different Facebook AST2500 OpenBMC
platforms.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
All IO mapped SoC peripherals should be within the "soc" node. Move the
L2 cache-controller there as well since it's the only one not following
this pattern.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200815182223.408965-1-martin.blumenstingl@googlemail.com
- Fix QuadSPI-memory 'reg' for LS1021A and GPIO 'ranges' for i.MX7ULP
pinctrl.
- A couple of DTC warning fixes on imx6qdl-gw51xx and imx6q-prtwd2
boards.
- Add missing imx8mm-beacon-kit.dtb to dtbs-y for build coverage.
- Fix broken PWM settings on imx6q-logicpd board.
- Add missing syscon compatible to OCOTP device, so that access to UID
is possible.
- Fix a network regression on imx7d-zii-rmu2 due to a phy-mode mismatch.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl9DuhsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5bSQf/b+yNiCFHg86Jmwcm+drrLRns8N6j
Xzy8U+LYxqjGyXOhYthuPU4K4y76qGh8Gaa1FlUJcaGdJ4nn/3RXw1kAAUaE9QT4
UDm/j5bdrDiyCOJf54XPOTjq9VVJjKuHa9yGQykTc7uI0pQ0O1zWWP1X1ZBV3Z7l
dCxtbBdvczrHW2sssCSyKL3YoTNo4TCXSE77TAFjVsz/VzbvuHXyn4GPDWt7jofz
4m/UEx4irNRwTuunJ9aFqVf6MsjrlHJYGHBqr1Oh2+uhoQpM5FbjuE436C8kgVpY
u/mKBf7UtnhWUQIG1O7/pCwojh3QKSh0p77swnau/sTzmVFZ7tzBe6WSAw==
=yno7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.9:
- Fix QuadSPI-memory 'reg' for LS1021A and GPIO 'ranges' for i.MX7ULP
pinctrl.
- A couple of DTC warning fixes on imx6qdl-gw51xx and imx6q-prtwd2
boards.
- Add missing imx8mm-beacon-kit.dtb to dtbs-y for build coverage.
- Fix broken PWM settings on imx6q-logicpd board.
- Add missing syscon compatible to OCOTP device, so that access to UID
is possible.
- Fix a network regression on imx7d-zii-rmu2 due to a phy-mode mismatch.
* tag 'imx-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
Link: https://lore.kernel.org/r/20200824130359.GF12776@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on the imx7d-zii-rmu2 board.
The end result is that network receive behaviour is marginal with lots of
RX CRC errors experienced and NFS frequently failing.
Quoting the explanation from Andrew Lunn in commit 0672d22a19
("ARM: dts: imx: Fix the AR803X phy-mode"):
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
Fix it by switching to phy-mode = "rgmii-id".
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Note that we also must tag rtc as disabled on am43x-epos-evm as
it's not accessible according to commit 4321dc8dff ("ARM: AM43XX:
hwmod: Add rtc hwmod"). And we must keep RTC enabled for rtcwake
to work now that we've removed the custom platfor code for
re-enabling the RTC on suspend.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DTC doesn't like the default PWM settings, because it's expecting
three cells. This patch reduces adds the extra entry of 0 to the PWM
reference.
Fixes: fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6q-prtwd2.dts:33.8-43.4: Warning (unit_address_vs_reg): /i2c@4: node has a unit name, but no reg or ranges property
Remove the unneeded i2c unit name to fix the issue.
Fixes: 88010b8174 ("ARM: dts: add Protonic WD2 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi:23.12-68.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unneeded #address-cells/#size-cells properties to fix the issue.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manual of the i.MX25 the function name for
the GPT capture input is called CAPIN1. So fix the names to follow the
same naming scheme as used for the other pads and functions. Also add
one missing pad function.
There are no mainline users that needs adaption.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reg property to each channel node. This update is
to accommodate the multicolor framework. In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds missing interrupt support for the internal Marvell
switch, so that the kernel does not have to keep polling the
PHYs on the bit-banged MDIO bus all the time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "DMIC" rounting, headphone and microphone detect gpio for sound
card, then output sound can switch between headphone and speaker.
input sound can switch between DMIC and AMIC.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I used the i.MX25 Reference Manual (Rev 2 01/2011) as source for these
additions and fixes.
No mainline dts is affected by the fixes (nor obviously by the
additions).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct gpio ranges according to i.MX7ULP pinctrl driver:
gpio_ptc: ONLY pin 0~19 are available;
gpio_ptd: ONLY pin 0~11 are available;
gpio_pte: ONLY pin 0~15 are available;
gpio_ptf: ONLY pin 0~19 are available;
Fixes: 20434dc92c ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OLED display consist of an OLED panel and a display controller.
The displays that were used on yapp4 platform were based on a SSD1305
controller. These displays are now discontinued and we need to add
support for a replacement.
The new display is based on SSD1309 controller and requires slightly
different configuration (mirror + segment offset). We want to support
both display types so it does no matter which one was used on the assembly
line. Hence the displays are placed at different I2C addresses.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree for new variant of the Y Soft IOT appliance.
The board is based on Hydra with the following changes:
- faster SoC (1GHz), 4GB RAM and 64GB eMMC
- removed miniPCIe
- removed Audio jack
- removed uSD slot
- removed RJ10 serial
- HDMI replaced by USB host
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX SoCs nand node name from "gpmi-nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX27 nand node name from "nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add aliases for ethernet switch ports to allow bootloader to fix
MAC addresses to the ones stored in onboard configuration EEPROM.
Ursa has only one ethernet port populated (eth2) so alias for
the first port has to be removed on this board.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for an update of the TQ-Systems TQMa7x/MBa7x DTS, add the
QSPI controller to imx7s.dtsi.
Based-on-patch-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the Reference Manual, the correct size is 512 MiB.
Without this fix, probing the QSPI fails:
fsl-quadspi 1550000.spi: ioremap failed for resource
[mem 0x40000000-0x7fffffff]
fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
fsl-quadspi: probe of 1550000.spi failed with error -12
Fixes: 85f8ee78ab ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, OMAP3_THERMAL is disabled by default, so the bandgap sensor
is unavailable, and enabling it will somewhat increase power consumption.
However for boards which operate near their thermal limit, OMAP3_THERMAL
can be enabled and monitored to keep the processor from either running
too fast, or shutdown when it's deemed to be operating at an unsafe
thermal limit at the expense of increased power consumption.
The OMAP3530, OMAP3630, and DM3730 all show thresholds of 90C and 105C
depending on commercial or extended temperature ratings.
This patch expands the thermal information to include the limits of
80C for alert and 90C critical based on commercial temperature rating.
It sets the coolings-cells for the 34xx and 36xx CPU's which will start
to throttle back their maximum frequency when the bangap sensor reads
above the alert temerature of 80C.
For boards who which to increase the temperatures for extended
temperature ratings, these can be changed on their respective
device trees with something like:
&cpu_alert0 {
temperature = <90000>; /* millicelsius */
};
&cpu_crit {
temperature = <105000>; /* millicelsius */
};
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> # on GTA04A5 with dm3730cbp100
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add label to the ocp node in the AM33xx SoC include so that it can be
referenced in board-level files like am335x-pocketbeagle.dts
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add am335x-moxa-uc-8100-common.dtsi for many products of MOXA UC-8100
series, and remove common nodes from am335x-moxa-uc-8100-me-t.dts.
Signed-off-by: Johnson Chen <johnsonch.chen@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add information about panel orientation, so that the
system boots into a properly rotated shell.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Droid 4 specific compatible value in addition to the
generic one, so that we have the ability to add panel
specific quirks in the future.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The standard binding for DSI requires that the channel number
of the panel is encoded in DT. This adds the channel number in
all OMAP3-5 boards in preparation for using common infrastructure.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We currently have a different clock rate for droid4 compared to the
stock v3.0.8 based Android Linux kernel:
# cat /sys/kernel/debug/clk/dpll_*_m7x2_ck/clk_rate
266666667
307200000
# cat /sys/kernel/debug/clk/l3_gfx_cm:clk:0000:0/clk_rate
307200000
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSI was not probing due to base address off by 0x1000, and sys_clk
missing.
With this patch, the Pyra display works if HDMI is disabled in the
device tree.
Fixes: 5a507162f0 ("ARM: dts: Configure interconnect target module for omap5 dsi1")
Signed-off-by: David Shah <dave@ds0.me>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
[tony@atomide.com: standardized subject line, added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The chip is hardwired to the board's PCIe bus and needs to be properly
setup trough a firmware routine after a PCI fundamental reset. Pass the
reset controller phandle that takes care of triggering the
initialization to the relevant PCI device.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-5-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the reset driver exposing Raspberry Pi 4's firmware based USB
reset routine is available, let's add the device tree node exposing it.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can power off l4_abe domain when not in use when we configure it for
genpd. And with that change, we can now also drop the old unused legacy
platform data.
Note that we also need to now use "simple-pm-bus" instead of "simple-bus"
for PM runtime to get enabled for the bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can power off the SGX power domain when not in use when we configure
it for genpd. And with that change, we can now also drop the old unused
legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the devicetree properties to enable instruction and data prefetch
on exynos4210 and exynos4412 which use the L2C-310 cache. No other
Exynos chip appears to be using this L2 cache hardware.
This follows the default bits being set in the l2c_aux_val register
for the Exynos platform, which can now be cleared as a result.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Update the never-mainlined "samsung,trats2-audio" binding and instead
use the new "samsung,midas-audio" binding.
Signed-off-by: Simon Shields <simon@lineageos.org>
[s.nawrocki: fixed DAPM routing entries for MICBIAS1/2, adjusted to
new cpu/codec binding, corrected the regulator nodes indexing]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes the register address for the timer3 entry on Arria10.
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Configure the SAI device node, configure audio clock
and pinctrl.
Enable the audio sound card, which use the SAI1 and
wm8960, and enable headphone detection.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device trees for TQMa6S, TQMa6Q, and TQMa6QP embedded modules.
The A and B SoM variants are for hardware revisions that differ in
how the I2C devices are connected. For details, see [1].
This is a combination of the patches
"arm: dt: imx6qdl: add tqma6[qdl] som on mba6 mainboard",
"arm: dt: tqma6: add spi with spi nor flash on SOM",
"arm: dt: add basic support for tqma6qp on mba6", and
"arm: dt: imx6qdl-tqma6: use generic jedec,spi-nor"
from the TQMa6x BSP, with the MBa6 specific parts removed.
[1] https://support.tq-group.com/en/arm/tqma6x/linux/ptxdist/overview
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
[bst@pengutronix.de: remove unnecessary container node in the iomuxc
node]
Signed-off-by: Bastian Krause <bst@pengutronix.de>
[p.zabel@pengutronix.de: merged patches from TQMa6x BSP REV.0114,
separated MBa6 DTs, fixed checkpatch and dtbs_check warnings,
added no-sd(io) properties to eMMC, added SPDX license identifiers
and commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable Ethernet switch reset GPIO with ZII platforms that have it
enabled. HW switch reset results in a reset of the copper PHYs
inside of the switch. We want to avoid this reset of the copper PHYs
in the switch as this results in unnecessary broader network disruption on
a soft reboot of the application processor.
With the HW GPIO removed, the switch driver still performs a soft reset of
the switch core which has been shown to sufficiently meet our needs with
other ZII platforms that do not have the HW switch reset GPIO defined.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reset-gpio property, and enable PCIe on iMX6QP SABREAUTO board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous commit removed the panel-dpi driver, which made the
SOM-LV video stop working because it relied on the DPI driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the SOM-LV dev kits
to use a similar panel and remove the manual timing requirements.
A similar patch was already done and applied to the Torpedo family.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 739f85bba5 ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rng DT node was added without a compatible string.
i.MX driver for RNGC (drivers/char/hw_random/imx-rngc.c) also claims
support for RNGB, and is currently used for i.MX25.
Let's use this driver also for RNGB block in i.MX6SL.
Fixes: e29fe21cff ("ARM: dts: add device tree source for imx6sl SoC")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device node for the PCIe controller on the Renesas
RZ/G1H (r8a7742) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200810174156.30880-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a Display Unit (DU) node to r8a7742 SoC DT.
Boards that want to enable the DU need to specify the output topology.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200807174954.14448-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some r8a7745-iwg22d-sodimm.dts device nodes are not sorted alphabetically.
This patch fixes the sorting of nodes and also fixes a typo in the stmpe
node.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200805142634.12252-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl8v8lsACgkQQRCzN7AZ
XXP9XhAAqDOOMioRhcTnKkJkocbiBiKt0VTi6ZQhmqp2h5EOWgsLjht20vaiQehc
zWrqIbre7oZTHyvzLF9hGoxVEiv6v25J/mYjyz8py/3bm1McfTjwPtIQEcI8QppP
CcMFU0KkKQ//XrR/Efl9t9Zy+1ifXJ6N0Ck4pXuHyju8KnckR6URrx6SMZoB/NpO
0mA1AKpkg4c1IMOae57tkRC2R9iZGKTPNLxqBmvn9aroztooVIoAQ7MHNmn8QnQo
Nh4rgTG6M7HJlJ709j4KxpUQzEFjMXXpoMERtU+0/cYcW78i35s2phQ6cKug0sqa
6v6cDj+/4QiwbQAfA7CTVBEtKFeMbWaAteYO2YM/h0Fo0yoOeChU97g3gmer0L+h
F/47O0KIWu0xVluOJSDhDW8PpvONHsnpEIfu5LbzJjnV+VpiidKJD2D0jgfoHxL5
Re3yyxK5dTOGqQW2uB84UjkGjVTWT+s4CMBEfcTaaZB9fH4a7vmWQbcaVskSeDaN
KjP2c2NfTJMd2p4oruGrUuEtcpVpnb8K0GEkBHTsqokG9ubVrlJHy8wyO/VvMfpI
gG9ztEkKe6DSw/bGXyks6iP0l4DjvDRhS1Hb5d1ojj3SQLTpwllxnxSygnvYb9wl
RPcJ1xB8YLy+Q8f6usQMwwPA1t10K3HUB6A9aJx4ATWXFR5eACY=
=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
There are three SoC families newly dded to the 32-bit and
64-bit Arm architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012. For
now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl8j31MACgkQmmx57+YA
GNnS7Q//achCOtBeIblV8Fyfp/lTYNpT9hFTQ5cGaoyjl9Lm1rcVCISCEGqIEJAV
FRQBz3YcQWA9pIWIf79oh6QphcoW/wUTCE+cjnHP+EOkqvw9aGFBm4nOUt4Gz92a
+gGs9HqcrxB+3ysQEDGugwRrE6htrOoCnWyurh5zZNvAEry+MV6LBwfxSUrLKy8b
iwnwl/KvWI47mWAj5nJ7fbXAgxRjFdEz+mvNBjqKhJ/OELsnWRXcxmJxF651DEb6
e/ydD7OtrWI1+81/yQxS7SeDlatFHE0JvP4WZHBGm6TB7Z3pdqIZI598UN0lVvbR
jvtljiAa2UA7h6NjscD6ECWktrF8LO8i/8ref7Fr3za/FKiLTYP2BQymnlk5nLAj
RuCvR8oriqBbseZlkGrs4afjpfwurUKNhhjVse/M3ORYYK++Bra6GZWL4gnlA2wB
GbFZ6MAw2bnbKrO6rRTu+F1NFq5/l71LP1r3Li3xbyfZ7I/XJ5aiE6knQ+vtk6Np
pfvCYSILOSnulYZvdaL/W4HV98mzjHSE4eUegGDTMKNv2dVNRGI3Mnnur7+kSXLu
550qg+GXv8JkQlkFkT2BsuaiPULOUKHFtK42fo2XhQL/zoaFlBU7HehtSBdtcKPy
XIlEEk32q+QyABKav2QJnGJMcWzfq2SSmsUliVU72zD38dG/0Fw=
=Yy3D
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds
a workaround for a problem with cpuidle support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl8j32AACgkQmmx57+YA
GNkoXA//RHlx49SRw9RXxrMHwPTq0L12R2YJsHoCw3GYmAi7MkLiSy+VsR0b8LON
vtflUwyVBDr6THlPYKqq/nBEaXQAHUd8xm5HQSwsgWdAcxwpvI2VQ8AFwCUIJOn5
I2a2kVNMTV7I7E1j64RpdoErtJiGlIFR6Yv7j1ENUBurTXT5KzGyugms1eHqSmNi
I1zVHzbvJji+vTxnDy2ooUyig04GP+8hY1/ZrwvStfruWZYckaeXCQIWvkExaqp5
pPnCTPrrnhKg44Nlco88QjoScz8vzGcLBXF0VpLhjD3J/IO/ySWuyBmRLZNS4VzU
c2zyQ6xnSLbC6QnQa6YYMwC6xVmYfzdudXORVM2sLAGsUH1XMV6zHbJ+dP6WGTjd
yfgkgr2bindbhSTuYKoyP5Km2MizW7ndTStpBKbdSR63kwF70POEAZPR9SZsoZcR
6gyaKNVqd3Xcuht3MfndR0WrYcTnzsz+EcioLP3AdQxfI2fM3l5NIqbtOt9txHi0
CcaVfK9k7sKGWkWHlcurrkB6kTDnlJYR6S1ZiiJMb+nriQAXkQjw+wuF6hb9qvIJ
sCKNFdVc8x+b0qf/CO1iss/H0s5dv2bzlXL/YgRUcpcLJ/zVEb1Cgl+Dx496pEwl
dEsMueRlfx9kvmZLkVJMHY5hTBDHaaDRHqmqaQpTcHdHDIwAGA4=
=IHpg
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds a
workaround for a problem with cpuidle support"
* tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh()
MAINTAINERS: arm/amlogic: add designated reviewers
ARM: davinci: dm646x-evm: Simplify error handling in 'evm_sw_setup()'
ARM: davinci: Fix trivial spelling
ARM: davinci: Replace HTTP links with HTTPS ones
ARM: s3c24xx: Replace HTTP links with HTTPS ones
ARM: orion/gpio: Make use of for_each_requested_gpio()
ARM: at91: Replace HTTP links with HTTPS ones
ARM: at91: pm: add missing put_device() call in at91_pm_sram_init()
ARM: rpc: Change blacklist to quirklist in ecode.c file
ARM: OMAP: Replace HTTP links with HTTPS ones
ARM: s3c24xx: leds: Convert to use GPIO descriptors
udc: lpc32xx: mark local function static
ARM: exynos: MCPM: Restore big.LITTLE cpuidle support
ARM: exynos: clear L310_AUX_CTRL_FULL_LINE_ZERO in default l2c_aux_val
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
The compatible string for the pmsleep region has changed.
Update the MStar/Sigmastar v7 base dtsi with the new string.
Link: https://lore.kernel.org/r/20200729150748.1945589-4-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in
an earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the H6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qXc9
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC DT fixes from Arnd Bergmann:
"These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in an
earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the
H6"
* tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: keystone-k2g-evm: fix rgmii phy-mode for ksz9031 phy
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
MStar v7 SoCs support reset by writing a magic value to a register
in the "pmsleep" area.
This adds a node for using the syscon reboot driver to trigger a reset.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a node for the pmsleep area so that other
drivers can access registers contained within it.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mercury5 family chips have 128KB of SRAM in the IMI region.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All MStar v7 SoCs have an internal SRAM region that is between 64KB
(infinity2m) and 128KB(infinity3, mercury5).
The region is always at the same base address and is used for the
second stage loader (MStar IPL or u-boot SPL) and will be used for
the DDR self-refresh entry code within the kernel eventually.
This patch adds a 128KB region to the SoC and the minimum 64KB SRAM
region to the base dtsi. Families with more SRAM will override the
size in their family level dtsi.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial support for the 70mai midrive d08 dash camera.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BreadBee is an opensource development board based on the
MStar msc313(e) SoC.
Hardware details, schematics and so on can be found at:
https://github.com/breadbee/breadbee
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a family level dtsi for the mercury5 and then a
chip level dtsi for the ssc8336n chip.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds two family level dtsis for the infinity and infinity3
and then adds a chip level dtsi each for a chip in those families.
infinity3.dtsi includes infinity.dtsi as these SoCs share most of
their memory map and we would have a lot of duplication otherwise.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial dtsi for the base MStar/Sigmastar Armv7 SoCs.
These SoCs have very similar memory maps and this will avoid
duplicating nodes across multiple dtsis.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on keystone-k2g-evm board.
The above board have phy-mode = "rgmii-id" and it is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay by default.
After above commit, the KSZ9031 PHY starts handling phy mode properly and
enables both RX and TX delays, as result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
-----BEGIN PGP SIGNATURE-----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=ibOR
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic: updates for v5.9 (round 2)
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: meson-g12: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gxm: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gx: add the Mali-450 OPP table and use DVFS
arm64: dts: meson: add support for the WeTek Core 2
dt-bindings: arm: amlogic: add support for the WeTek Core 2
arm64: dts: meson: add audio playback to khadas-vim3l
arm64: dts: meson: add audio playback to odroid-c4
arm64: dts: meson: update spifc node name on Khadas VIM3/VIM3L
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
Link: https://lore.kernel.org/r/7h8sf8671u.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqaPwAKCRALBhiOFHI7
1YANAKCEUNj0n91jslQNBACKuB7a79Ag3ACbB/hWOsGi+BVNlDy5mnXeoT5ZEd0=
=GJyb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.8 (part 1)
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
* tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqh0gAKCRALBhiOFHI7
1R9KAJ0TuEHE0boReOUAhpAlfYIqYeR5QQCfUuD/p2aoTSfNNyctLQsHmnjBYao=
=PzgE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.9 (part 1)
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
* tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dlink-dns327l: fix reg-init PHY
ARM: dts: kirkwood: Replace HTTP links with HTTPS ones
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To support the change in "phy: armada-38x: fix NETA lockup when
repeatedly switching speeds" we need to update the DT with the
additional register.
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
=DXTp
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl8YzOAQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgY9aB/0folCAovUA97bILQR/62PspVGR1i/S2GJe
sQqKuWDyBtJNM3IYNVMd/AtcrP+U0ZD4MX6TKbabs+ZuIc4EksXRroMTMm2azme1
rOrQuGSKcdhPobJOHlpbSC/QPWWi5GGGWDnwXY8T68NedeYLP/o8sOmZQtUi80R9
ueP5ZwiviwMrVzRITPb8sB89WEyRqaas2H0fc/4OjGRY/jeTKwCk9sP/JytA6gUB
/GXn+uUk5WcRkekujBi1LVi4BIhm7PMW9kM1AHWAV6+2Yd8uFyG4ut9MB7SmaQt8
QfEoPpLvQicpZCVB3VFOPJ38z4YuOXsqo85u8T3ZkgpLdInoa/J9
=GUhq
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Biggest part is the addition of the rk3288 variant of the VMARC
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
* tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add PCIe for RockPI N10
ARM: dts: rockchip: Add HDMI out for RockPI N8/N10
ARM: dts: rockchip: Add USB for RockPI N8/N10
ARM: dts: rockchip: Add usb host0 ohci node for rk3288
ARM: dts: rockchip: Fix VBUS on rk3288-vyasa
ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
ARM: dts: rockchip: Add VMARC RK3288 SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N8 binding
arm64: dts: rk3399pro: vmarc-som: Move common properties into Carrier
arm64: dts: rk3399pro: vmarc-som: Move supply regulators into Carrier
arm64: dts: rk3399pro: vmarc-som: Fix sorting nodes, properties
ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOM
ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmac
ARM: dts: rockchip: Add marvell BT irq config
ARM: dts: rockchip: rename label and nodename pinctrl subnodes that end with gpio
Link: https://lore.kernel.org/r/2472314.kD9Egx1jfM@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the audio SRAM, DMA engine, I2S interface, and codec, hooks
them together and adds a audio-graph-card instance.
It also removes the jack gpios from the gpio-keys instance, because the
audio jack driver registers an input device.
Link: https://lore.kernel.org/r/20200718205019.184927-10-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This memory is region is where the two-channel audio DMA can pump sound
samples into the SSPA's internal FIFO.
Link: https://lore.kernel.org/r/20200718205019.184927-6-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ACGR register is at the offset of 0x1024, beyond the 4k originally
assigned to the MPMU range.
Link: https://lore.kernel.org/r/20200718205019.184927-5-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The power management unit, described by the soc_clocks node, controls the
power to the peripherals by the means of power domains with a single
cell -- the domain number.
Link: https://lore.kernel.org/r/20200718205019.184927-4-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the XO-1.75, this node represents a bus interface that operates in slave
mode and thus is only able to accommodate a single subnode; no address
cells are necessary.
The Documentation/devicetree/bindings/spi/spi-controller.yaml binding
prefers that we drop the property instead of setting it to zero.
This fixes a DT validation error:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
{ ... } is valid under each of {'required': ['spi-slave']},
{'required': ['#address-cells']}
We also need to drop #size-cells:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
'#address-cells' is a dependency of '#size-cells'
Link: https://lore.kernel.org/r/20200718205019.184927-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: $nodename:0:
'camera_i2c' does not match '^i2c(@.*)?'
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'sda-gpios' is a required property
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'scl-gpios' is a required property
The "gpios" property actually was documented as deprecated, but got dropped
in commit 0175ce4a58 ("dt-bindings: i2c: Convert i2c-gpio binding to
json-schema"). It's probably best kept forgotten though.
Link: https://lore.kernel.org/r/20200718205019.184927-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
-----BEGIN PGP SIGNATURE-----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=ga5j
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.9, round 1
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
* tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (38 commits)
ARM: dts: stm32: enable usb-role-switch on USB OTG on stm32mp15xx-dkx
ARM: dts: stm32: Add compatibles for syscon for stm32mp151
ARM: dts: stm32: Add compatibles for syscon for stm32h743
ARM: dts: stm32: Add compatibles for syscon for stm32f746
ARM: dts: stm32: Add compatibles for syscon for stm32f426
dt-bindings: arm: stm32: Add compatibles for syscon nodes
ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl
ARM: dts: stm32: configure i2c5 support on stm32mp15xx-dkx
ARM: dts: stm32: add usart2 node to stm32mp157c-dk2
ARM: dts: stm32: add uart7 support to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart3 node to stm32mp157c-ev1
ARM: dts: stm32: add usart3 node to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl
ARM: dts: stm32: cosmetic updates in stm32mp15-pinctrl
ARM: dts: stm32: fix uart7_pins_a comments in stm32mp15-pinctrl
ARM: dts: stm32: fix uart nodes ordering in stm32mp15-pinctrl
ARM: dts: stm32: Update UART4 pin states on stm32mp15xx-dkx
ARM: dts: stm32: Update pin states for uart4 on stm32mp157c-ed1
ARM: dts: stm32: update uart4 pin configuration for low power on stm32mp157
dt-bindings: usb: dwc2: Fix issues for stm32mp15x SoC
...
Link: https://lore.kernel.org/r/8a9bb27b-fc08-126a-11f7-01354e8577e1@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
-----BEGIN PGP SIGNATURE-----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=k3pO
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.9
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
* tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Replace HTTP links with HTTPS ones
ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family
ARM: dts: exynos: Define fixed regulators in root node for consistency in SMDK5420
ARM: dts: exynos: Define fixed regulators in root node for consistency in Arndale
ARM: dts: exynos: Define fixed regulators in root node for consistency in Origen
ARM: dts: exynos: Remove DMA controller bus node name to fix dtschema warnings
ARM: dts: exynos: Fix missing empty reg/ranges property regulators on Trats
ARM: dts: exynos: Align L2 cache-controller nodename with dtschema
ARM: dts: s5pv210: Correct BCM4329 bluetooth node
ARM: dts: s5pv210: Add BMA023 accelerometer support to Aries
ARM: dts: s5pv210: Add support for GP2A light sensor on Aries
ARM: dts: s5pv210: Correct fuelgauge definition on Aries
ARM: dts: s5pv210: Add interrupt-controller property to gph3
ARM: dts: exynos: Enable Bluetooth support for Artik5 board
ARM: dts: exynos: Extend all Exynos5800 A15's OPPs with max voltage data
Link: https://lore.kernel.org/r/20200721180900.13844-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
-----BEGIN PGP SIGNATURE-----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=wWXD
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.9
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
* tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add qfprom definition to ipq806x
ARM: dts: qcom: Add MikroTik RB3011
ARM: dts: qcom: add ethernet definitions to ipq8064
Link: https://lore.kernel.org/r/20200721045032.3430395-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlZAAKCRDj7w1vZxhR
xft/AQCaR2CkyOVyK32yPUX0ZF2nS+LYzalJIUpOuLhy37GQVwEA+vlQTa7fKdtW
4IX58peBkRD8FwTszrwR/tImDPd8Rwg=
=z8pA
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
* tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: bananapi-m2-plus-v1.2: Tie in CPU OPPs
arm64: dts: allwinner: h5: libretech-all-h3-cc: Tie in CPU OPPs
arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
arm64: dts: allwinner: h5: Add trip and cooling maps to CPU thermal zones
arm64: dts: allwinner: h5: Add clock to CPU cores
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores
ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU cores
arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V
arm64: dts: allwinner: Add support for PinePhone revision 1.2
dt-bindings: arm: sunxi: Add PinePhone 1.2 bindings
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
ARM: dts: orange-pi-zero-plus2: add leds configuration
ARM: dts: orange-pi-zero-plus2: enable USB OTG port
Link: https://lore.kernel.org/r/fa48ffcb-3404-41bb-b065-a16717cf5688.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
just a single patch fixing up the node names for schema.
-----BEGIN PGP SIGNATURE-----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=xBG2
-----END PGP SIGNATURE-----
Merge tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS changes for the v5.9 kernel cycle, essentially
just a single patch fixing up the node names for schema.
* tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: arm-realview: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/CACRpkdbkM9ZmuG2FnBmO7upcJfnqq2oSLDCFDXC5b3K+dtps9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VVgcUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7azwf+KzAukegArKtAmsbAnYNKYztXXifW
6Hc3+hv2mfUtsGfHPSUJJ5MhEW52xAbcXnYETUkmoWe1W1zIxrNNWvBUm4nPF5os
0cO8tjk4cE4CYDnsl8sBSqT55sd3ke61I+j9q0NAQNyX9OlmZ3kfm8yw0yIsxTKp
/FzoLmOeRzhVKHdZczuJ9Ts4kFyf3XtQrrN1UTbu715KdIbbsrJtXQ74ADBCnjfX
8RUm3Y5XIaPcF4z2U8reMsbHCF120ENIfGwFRNo/Odx+1OVo1IrDB1+f/SP9ZP0T
6+iKvfSS4RavzB1tvLdJ2/911t7qtqsneU33kwQKL0wrFZsT4ih42uBfpw==
=1hHY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update for 5.9:
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
ARM: dts: imx6q-tbs2910: Pass reset-assert-us
ARM: dts: imx6q-tbs2910: Add an mdio node
ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
ARM: dts: imx6qdl-sabresd: Add an mdio node
ARM: dts: imx6qdl-gw: add Gateworks System Controller support
ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
ARM: dts: vf610-zii-spb4: Add node for switch watchdog
ARM: dts: colibri-imx6: remove pinctrl-names orphan
ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
ARM: dts: ZII: update MDIO speed and preamble
ARM: dts: vfxxx: Add node for CAAM
ARM: dts: imx6qp-sabresd: enable sata
ARM: dts: imx6qp-sabreauto: enable sata
ARM: dts: add Protonic RVT board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic WD2 board
...
Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VFn0UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM52gQf+OGrSQq1t77ltL5EKeeV8f+PCu7UP
X7I2IJY+9FIYA1wuu0/AuhHaJ9NR0hN2mZVT+ktmxIDMVuHZJpAuHRfGp7anfVKr
vo1JgT9CbVZ/kD0n5a6TN28Kb7DVkIM4QGcEJuCD2mb1UJarlVX8YHg9Otv7b26p
3arPLR8eocPh2jNNdYnwSoZ8Li7Dm1SQloRAoCJOHAgAuSAdhG15rJBG70zX0F7d
QEWu6tNjN8FSrWeT1GLlzywYxGp1t592yuUpKAoppuJgxyUPIYA15vRB0d/KRqUL
CWYrDNh/dAvafI9HfeQQK5BjQhW58gy2c38s+bR9iPGoy88GzZiy+AatYQ==
=NlnX
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 3:
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
* tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
Link: https://lore.kernel.org/r/20200720040148.GA20462@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
were failing on older SoCs and one to fix Cedrus on the H6.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlyQAKCRDj7w1vZxhR
xcNtAQDO2rSFHGpQsUE/MCRxMqd2c2OQ9zpovRnirnyJqLCPEwD/b8GAi9tfJksM
lmghSQnByq6Sqm9UA/i6jjLfz//4iQg=
=JoYD
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that
were failing on older SoCs and one to fix Cedrus on the H6.
* tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
Link: https://lore.kernel.org/r/e24f0608-6a4f-4163-b99e-a5f48e796184.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and boards
can then enable it if supported.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20200720105846.367776-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[nsekhar@ti.com: drop obsolete hawkboard.org URL completeley
fixup subject line prefix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that USB OTG driver supports usb role switch by overriding PHY input
signals (A-Valid, B-Valid and Vbus-Valid), enable it on stm32mp15xx-dkx.
dr_mode needn't to be forced to Peripheral anymore, it is set to OTG in
SoC device tree.
USB role (USB_ROLE_NONE, USB_ROLE_DEVICE, USB_ROLE_HOST) will be provided
by STUSB1600 Type-C controller driver.
This patch depends on "Add STUSB160x Type-C port controller support"
series, which is under review.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins
are not in BANK Z.
Fixes: 498a701498 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure I2C5 on stm32mp15 DK boards. It's available and can be used on:
- Arduino connector
- GPIO expansion connector
Keep it disabled by default, so the pins are kept in their initial state to
lower power consumption. This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart2 node to stm32mp157c-dk2 board. usart2 pins are connected
to Bluetooth component. usart2 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds uart7 node to stm32mp15xx-dkx and uart7 alias to stm32mp157a-dk1 and
stm32mp157c-dk2 boards. uart7 pins are connected to Arduino connector.
uart7 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart3 node to stm32mp157c-ev1 board. usart3 pins are connected to
GPIO Expansion connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart3 node to stm32mp15xx-dkx and usart3 alias to stm32mp157a-dk1
and stm32mp157c-dk2 boards. usart3 pins are connected to GPIO Expansion
connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use tabs where possible and remove multiple blanks lines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.
The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-4-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-3-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY"), networking is broken on sama5d3 xplained.
The device tree has phy-mode = "rgmii" and this worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200717233644.841080-1-alexandre.belloni@bootlin.com
Commit 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Fixes: 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.
[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected
The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.
This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.
[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2
Fixes: 6df11287f7 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8035 datasheet:
"When using crystal, the clock is generated internally after power is
stable. For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms
requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.
The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8031 datasheet:
"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.
The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The marvell PHY reg-init registers for the D-Link DNS-327L are wrong.
Currently the first field is used to set the page 2, but this is
pointless. The usage is not correct, and we are setting the wrong
registers.
Fix it.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Connect the voltage regulator of vbus to the otg connector.
Depending on the current mode this is enabled (in "host" mode")
or disabled (in "peripheral" mode). The regulator must be updated
if the controller is configured in "otg" mode and the status changes
between "host" and "peripheral".
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200707101214.2301768-1-michael@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-8-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- eMMC: 16GB/32GB/64GB
- SD slot
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some of gmac, sdmmc node properties are common across rk3288 and
rk3399pro SOM's so move them into Carrier dtsi.
Chosen node is specific to rk3399pro configure SBC, so move it into
RockPI N10 dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Supply regulators are common across different variants of vmarc SOM's
since the Type C power controller IC is part of the carrier board.
So, move the supply regulators into carrier board dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-4-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C nodes and associated slave devices defined in Carrier board
are specific to rk3399pro vmrac SOM.
So, move them into SOM dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This time there are a number of actual code fixes, plus
a small set of device tree issues getting addressed:
- Renesas:
- one defconfig cleanup to allow a later Kconfig change
- Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
- TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
- NXP i.MX
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
- Amlogic Meson
- misc DT fixes
- SoC ID fixes to detect all chips correctly
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Xlng
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
-----BEGIN PGP SIGNATURE-----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=oFYm
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.9-rc1
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
* tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (38 commits)
ARM: tegra: Add device-tree for ASUS Google Nexus 7
ARM: tegra: Add device-tree for Acer Iconia Tab A500
ARM: tegra: Add HDMI supplies on Nyan boards
ARM: tegra: Add missing DSI controller on Tegra30
ARM: tegra: Add i2c-bus subnode for DPAUX controllers
ARM: tegra: The Tegra30 SDHCI is not backwards-compatible
ARM: tegra: The Tegra30 DC is not backwards-compatible
ARM: tegra: Remove spurious comma from node name
ARM: tegra: Add parent clock to DSI output
ARM: tegra: Use standard names for SRAM nodes
ARM: tegra: seaboard: Use standard battery bindings
ARM: tegra: Use standard names for LED nodes
ARM: tegra: Use numeric unit-addresses
ARM: tegra: medcom-wide: Remove extra panel power supply
ARM: tegra: Use proper unit-addresses for OPPs
ARM: tegra: Add missing clock-names for SDHCI controllers
ARM: tegra: Fix order of XUSB controller clocks
ARM: tegra: Add #reset-cells to Tegra124 memory controller
ARM: tegra: Add missing panel power supplies
ARM: tegra: Add micro-USB A/B port on Jetson TK1
...
Link: https://lore.kernel.org/r/20200717161300.1661002-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The device node for the FIFO-buffered Serial Interface sound node lacks
the "clocks" property, as the DTS file didn't describe any clocks yet at
its introduction.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200519075525.24742-1-geert+renesas@glider.be
Fix dtschema validator warnings like:
l2-cache: $nodename:0: 'l2-cache' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
-----BEGIN PGP SIGNATURE-----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=IlyP
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More dts changes for omaps for v5.9
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
* tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT
ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP
ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP
ARM: dts: omap5-uevm: Add system timers to DSP and IPU
ARM: dts: omap5-uevm: Add CMA pools and enable IPU & DSP
ARM: dts: omap5: Add aliases for rproc nodes
ARM: dts: omap5: Add DSP and IPU nodes
ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU
ARM: dts: omap4-panda-common: Add CMA pools and enable IPU & DSP
ARM: dts: omap4: Add aliases for rproc nodes
ARM: dts: omap4: Add IPU DT node
ARM: dts: omap4: Update the DSP node
ARM: dts: omap5: Add timer_sys_ck clocks for timers
ARM: dts: omap4: Add timer_sys_ck clocks for timers
ARM: dts: am335x-pocketbeagle: set default mux for gpio pins
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
-----BEGIN PGP SIGNATURE-----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=4iOb
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop more legacy platform data for omaps for v5.9
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
* tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for omap5 usb host
ARM: OMAP2+: Drop legacy platform data for omap4 usb
ARM: OMAP2+: Drop legacy platform data for dra7 dwc3
ARM: OMAP2+: Drop legacy platform data for omap5 dwc3
ARM: OMAP2+: Drop legacy platform data for am4 dwc3
bus: ti-sysc: Add missing quirk flags for usb_host_hs
ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
-----BEGIN PGP SIGNATURE-----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=ekbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8-rc cycle
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
* tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8Nxv4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4fIAf/SKUzFbQ/INaU98yW8zONnZVzD/jI
3oTnBP87YJRNiyrLF1lWLs55vfnhum7yXJZXdMbwP55fdJKVaV4StePGz9Sh4Gba
4COHOF3XvF73b4kpcCQEr1U+Y0KHEfMbkwONmerk9ZkRThY2uqcRsdj4br+XA9eU
19ppWdOYZHMjegPu0KuxJlevZJDO6s9I4MCKFWmGgWhanLeGXXd2xtJEgqTWtTnS
EFjOFdBQF+5yd0VY/j6WHBDHWa/fXhDFoAO8Wc5LMCP3VybZdciIi4mN8y0UZoNG
Q5UnBvpYMCqrBwVlyqgeDtJUvYd+33dHqsRbU3KN8yBpRnyHupR9UvcFLA==
=+Gmy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are few hardware variants of NVIDIA Tegra30-based Nexus 7 device:
1. WiFi-only (named Grouper)
2. GSM (named Tilapia)
3. Using Maxim PMIC (E1565 board ID)
4. Using Ti PMIC (PM269 board ID)
This patch adds device-trees for known and tested variants.
Link: https://wiki.postmarketos.org/wiki/Google_Nexus_7_2012_(asus-grouper)
Tested-by: Pedro Ângelo <pangelo@void.io>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Zack Pearsall <zpearsall@yahoo.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix dtschema validator warnings like:
l2-cache@fffff000: $nodename:0:
'l2-cache@fffff000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for Nyan boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 has a DSI controller, although it is never used on any of the
devices supported by the upstream Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX controller device tree bindings require the bus to have an
i2c-bus subnode to distinguish between I2C clients and pinmux groups.
Signed-off-by: Thierry Reding <treding@nvidia.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Got following d_can probe errors with kernel 5.8-rc1 on am437x
[ 10.730822] CAN device driver interface
Starting Wait for Network to be Configured...
[ OK ] Reached target Network.
[ 10.787363] c_can_platform 481cc000.can: probe failed
[ 10.792484] c_can_platform: probe of 481cc000.can failed with error -2
[ 10.799457] c_can_platform 481d0000.can: probe failed
[ 10.804617] c_can_platform: probe of 481d0000.can failed with error -2
actually, Tony has fixed this issue on am335x with the patch [3]
Since am437x has the same clock structure with am335x
[1][2], so reuse the code from Tony Lindgren's patch [3] to fix it.
[1]: https://www.ti.com/lit/pdf/spruh73 Chapter-23, Figure 23-1. DCAN
Integration
[2]: https://www.ti.com/lit/pdf/spruhl7 Chapter-25, Figure 25-1. DCAN
Integration
[3]: commit 516f1117d0 ("ARM: dts: Configure osc clock for d_can on
am335x")
Fixes: 1a5cd7c23c ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
[tony@atomide.com: aligned commit message a bit for readability]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-4-martin.blumenstingl@googlemail.com
EC-100 has built-in eMMC flash which is hard-wired to 3.3V VCC (which
means it's limited to high-speed MMC modes). Enable the SDHC controller
to access the contents of the eMMC flash.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-3-martin.blumenstingl@googlemail.com
Meson6, Meson8, Meson8b and Meson8m2 are using a similar SDHC controller
IP which typically connects to an eMMC chip (because unlike the SDIO
controller the SDHC controller has an 8-bit bus interface).
On Meson8, Meson8b and Meson8m2 the clock inputs are all the same.
However, Meson8m2 seems to have an improved version of the SHDC
controller IP which doesn't require the driver to wait manually for a
flush of a DMA transfer. Thus every SoC has it's own compatible string
so if more difference are discovered they can be implemented.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-2-martin.blumenstingl@googlemail.com
The Meson8b SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-4-martin.blumenstingl@googlemail.com
The Meson8m2 SoCs has introduced additional reset lines for the VPU
compared to Meson8. Also it uses a slightly different VPU clock
frequency compared to Meson8 since it can now achieve 364MHz thanks to
the addition of the GP_PLL.
Add the reset lines, VPU clock configuration and update the compatible
string so the implementation differences can be managed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-3-martin.blumenstingl@googlemail.com
The Meson8 SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-2-martin.blumenstingl@googlemail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices for the OMAP5 uEVM board. The following timers (same as the
timers on OMAP4 Panda boards) are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M4 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices on all the OMAP4-based Panda boards. The following timers
are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M3 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices for the OMAP5 uEVM boards. The following timers
(same as the timers on OMAP4 Panda boards) are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M4 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on the OMAP5 uEVM board. These nodes are assigned
to the respective rproc device nodes, and both the IPU and DSP remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP5 boards. The aliases uses
the stem "rproc", and are identical to the values
chosen on OMAP4 boards.
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, like OMAP4, also has two remote processor subsystems,
DSP and IPU. The IPU subsystem though has dual Cortex-M4
processors instead of the dual Cortex-M3 processors in OMAP4,
but otherwise has almost the same set of features. Add the
DT nodes for these two processor sub-systems for all OMAP5
SoCs.
The nodes have the 'iommus', 'clocks', 'resets', 'firmware' and
'mboxes' properties added, and are disabled for now. The IPU node
has its L2 RAM memory specified through the 'reg' and 'reg-names'
properties. The DSP node doesn't have these since it doesn't have
any L2 RAM memories, but has an additional 'ti,bootreg' property
instead as it has a specific boot register that needs to be
programmed for booting.
These nodes should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. The
following DMTimers are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M3 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. These nodes
are assigned to the respective rproc device nodes, and both the
IPU and DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP4 boards. The aliases uses
the stem "rproc".
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DT node for the Dual-Cortex M3 IPU processor sub-system has
been added for OMAP4 SoCs. The L2RAM memory region information
has been added to the node through the 'reg' and 'reg-names'
properties. The node has the 'iommus', 'clocks', 'resets',
'mboxes' and 'firmware' properties also added, and is disabled
for now. It should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The compatible property for the DSP node is updated to match
the OMAP remoteproc bindings. The node is moved from the soc
node to the ocp node to better reflect the connectivity from
MPU side.
The node is updated with the 'ti,bootreg', 'clocks', 'resets',
'iommus', 'mboxes' and 'firmware' properties. Note that the
node does not have any 'reg' or 'reg-names' properties since
it doesn't have any L2 RAM memory, but only Unicaches.
The node is disabled for now, and should be enabled as per
the individual product configuration in the corresponding
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit d41e530409 ("clk: ti: omap5: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes except for the always-on timers 1 and 12.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 1c7de9f27a ("clk: ti: omap4: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These pins on the PocketBeagle P1 and P2 headers are connected to AM3358
balls with gpio lines, and these pins are not used for any other
peripherals by default. These GPIO lines are unclaimed and could be used
by userspace program through the gpiod ABI.
This patch adds a "default" state in the am33xx_pinmux node and sets the
mux for those pins to gpio (mode 7) and input enable.
The "pinctrl-single,bias-pullup" and "pinctrl-single,bias-pulldown"
pinconf properties are also set for each pin per the ball reset state in
section 4.2 of the datasheet [0].
This is the AM335x pin control register format in Table 9-60 [1]:
bit attribute value
----------------------------------
31-7 reserved 0 on reset
6 slew { 0: fast, 1: slow }
5 rx_active { 0: rx disable, 1: rx enabled }
4 pu_typesel { 0: pulldown select, 1: pullup select }
3 puden { 0: pud enable, 1: disabled }
2 mode 3 bits to selec mode 0 to 7
1 mode
0 mode
The values for the bias pinconf properties are derived as follows:
pinctrl-single,bias-pullup = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pullup = < 0x10 0x10 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 1 0 x x x | 0x10
enabled x 1 0 x x x | 0x10
disabled x 0 0 x x x | 0x00
mask x 1 1 x x x | 0x18
pinctrl-single,bias-pulldown = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pulldown = < 0x0 0x0 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 0 0 x x x | 0x00
enabled x 0 0 x x x | 0x00
disabled x 1 0 x x x | 0x10
mask x 1 1 x x x | 0x18
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
[tony@atomide.com: fixed typo for am3 vs am4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 5.9 please pull the following:
- Rafal specifies the switch ports for various Luxul devices (XAP-1410,
XAP-1510, XAP-1610, XWC-1000, XWC-2000, XWR-1200, XWR-3100, XWR-3150)
- Krzysztof fixes the L2 cache controller node name to conform to
dtschema
- Maxime introduces two new clock providers for Raspberry Pi 4, one to
support firmware based clocks and another one for the DVP block
feeding into the two HDMI blocks.
-----BEGIN PGP SIGNATURE-----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=/iqx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.9 please pull the following:
- Rafal specifies the switch ports for various Luxul devices (XAP-1410,
XAP-1510, XAP-1610, XWC-1000, XWC-2000, XWR-1200, XWR-3100, XWR-3150)
- Krzysztof fixes the L2 cache controller node name to conform to
dtschema
- Maxime introduces two new clock providers for Raspberry Pi 4, one to
support firmware based clocks and another one for the DVP block
feeding into the two HDMI blocks.
* tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Align L2 cache-controller nodename with dtschema
ARM: dts: BCM5301X: Specify switch ports for Luxul devices
ARM: dts: bcm2711: Add HDMI DVP
ARM: dts: bcm2711: Add firmware clocks node
Link: https://lore.kernel.org/r/20200707045759.17562-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes configures the GPIO line names for am335x beaglebone
black and pocketbeagle to make it easier to configure the pins. To make use
of the pins, we also add the gpio-ranges for am335x.
We also enable IPU and DSP repmoteproc for am5729-beaglebone-ai, and then
there are two non-urgent dtschema validator warning fixes.
-----BEGIN PGP SIGNATURE-----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=OvXQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.9 merge window
This series of changes configures the GPIO line names for am335x beaglebone
black and pocketbeagle to make it easier to configure the pins. To make use
of the pins, we also add the gpio-ranges for am335x.
We also enable IPU and DSP repmoteproc for am5729-beaglebone-ai, and then
there are two non-urgent dtschema validator warning fixes.
* tag 'omap-for-v5.9/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-pocketbeagle: add gpio-line-names
ARM: dts: am335x-boneblack: add gpio-line-names
ARM: dts: am33xx-l4: add gpio-ranges
ARM: dts: am5729-beaglebone-ai: Disable ununsed mailboxes
ARM: dts: am5729-beaglebone-ai: Enable IPU & DSP rprocs
ARM: dts: am: Align L2 cache-controller nodename with dtschema
ARM: dts: omap: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/pull-1594402929-762188@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add PCIe endpoint and PHY nodes for Pro5 SoC
- simplify device hierarchy of support-card.dtsi
-----BEGIN PGP SIGNATURE-----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=d0+s
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.9
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add PCIe endpoint and PHY nodes for Pro5 SoC
- simplify device hierarchy of support-card.dtsi
* tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: simplify support-card node structure
ARM: dts: uniphier: Add PCIe endpoint and PHY node for Pro5
ARM: dts: uniphier: Rename ethphy node to ethernet-phy
ARM: dts: uniphier: give fixed port number to support card serial
ARM: dts: uniphier: rename support card serial node to fix schema warning
ARM: dts: uniphier: add interrupts to support card serial
Link: https://lore.kernel.org/r/CAK7LNARGDcCKxV3-H7WmuZAVe49n0QF+672-KN0tsP0och0a_A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the MYiR imx6ULL based single board computer
equipped with on board 256MB NAND & RAM. The board also
provides expansion header for expansion board, but this
commit adds only support for SBC.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is not necessary without a pinctrl-0 statement. Remove this
orphan.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SFF soldered onto the board expect the ports to use 1000BaseX. It
makes no sense to have the ports set to SGMII, since they don't even
support that mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SFF soldered onto the board expects the port to use 1000BaseX. It
makes no sense to have the port set to SGMII, since it doesn't even
support that mode.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
l2-cache@a02000: $nodename:0:
'l2-cache@a02000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
l2-cache@40006000: $nodename:0:
'l2-cache@40006000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add MQS support. As the pin conflict with usdhc2, then need
to add a separate dts.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use kernel LED interface for the alarm LEDs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In imx6sll.dtsi, the ssi node name is different with other
platforms (imx6qdl, imx6sl, imx6sx), but the
sound/soc/fsl/fsl-asoc-card.c machine driver needs to check
ssi node name for audmux configuration, then different ssi
node name causes issue on imx6sll platform.
So we change ssi node name to make all platforms have same
name.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX6/i.MX7 SoCs usdhc node name from usdhc to mmc to be
compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX2/i.MX3/i.MX5 SoCs esdhc node name from esdhc to mmc to
be compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX27/i.MX31 node name from sdhci to mmc to be compliant
with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In latest i.MX6Q RM Rev.6, 05/2020, #90 SPI interrupt is reserved,
so remove it from GPC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change IIM node name from iim to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change OCOTP node name from ocotp to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value
999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6/7 SoCs' temperature sensor is inside anatop module from HW
perspective, so it should be a child node of anatop.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The audio codec on the GW551x routes to ssi1. It fixes audio capture on
the device.
Cc: stable@vger.kernel.org
Fixes: 3117e851ce ("ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device hierarchy is needlessly complex.
Remove the support-card node level, and move the ethernet and serial
nodes right under the system-bus node.
This also fixes the following warning from 'make ARCH=arm dtbs_check':
support-card@1,1f00000: $nodename:0: 'support-card@1,1f00000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds PCIe endpoint controller and PHY nodes for Pro5 SoC,
and also adds pinctrl node for PCIe.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This renames the node name "ethphy" to "ethernet-phy" according to
Documentation/devicetree/bindings/net/mdio.yaml.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As per 'struct mfd_cell ab8500_devs[]' there are not 1, but 3 PWM
devices on the AB8500. Until now, each of them have referenced
the same Device Tree node. This change ensures each device has
their own.
Due to recent `dtc` checks [0], nodes cannot share the same node
name, so we are forced to rename the affected nodes by appending
their associated numeric 'bank ID'.
[0] ste-ab8500.dtsi:210.16-214.7: ERROR (duplicate_node_names):
/soc/prcmu@80157000/ab8500/ab8500-pwm: Duplicate node name
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200622083432.1491715-1-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for the back and menu keys on golden.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200621193822.133683-2-nick.reitemeyer@web.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Increase #pinctrl-cells to 2 so that mux and conf be kept separate. This
requires the AM33XX_PADCONF macro in omap.h to also be modified to keep pin
conf and pin mux values separate.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lore.kernel.org/r/20200701013320.130441-3-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
'make ARCH=arm dtbs_check' emits the following warning:
uart@b0000: $nodename:0: 'uart@b0000' does not match '^serial(@[0-9a-f,]+)*$'
Rename the node to follow the pattern defined in
Documentation/devicetree/bindings/serial/serial.yaml
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
Since then, 'make ARCH=arm dtbs_check' is so noisy because the
required property 'interrupts' is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove the regulators node and define fixed regulators directly under
the root node. This makes SMDK5420 board consistent with other Exynos
boards.
Name the fixed regulator nodes consistently.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the regulators node and define fixed regulators directly under
the root node. This makes Exynos5250 Arndale board consistent with
other Exynos boards.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the regulators node and define fixed regulators directly under
the root node. This makes Exynos4412 Origen board consistent with other
Exynos boards.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
- The first one based on the enhancements made to clk-raspberrypi, which
is now registered trough DT and provides control over the whole range
of firmware based clocks.
- The second one based on the new clk-bcm2711-dvp driver, which gates
the clocks and reset signals that feed into RPi4's HDMI0/1 blocks.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEErOkkGDHCg2EbPcGjlfZmHno8x/4FAl8DWigACgkQlfZmHno8
x/7FcggAhmCkN1I5zf7j3qDFNjIgg2sGl3JVmCasBdT8BK0yx7+5tcT3SHu9mOM0
o+8CngXUV+Tnl7LRIR0SJHtuiQkbh1MW9BAQMGrAMk+HDIzH957ki70kAp6kbLPE
EfQIrp0XCH6TXF0tpDbwpcJNQS3zpBC8cn8XgKnhVJbSnMHznP4a7iM6StvdRAov
umz65w/5QPMddvUFUVzGY1/+NVaEdqyE59xQQeoh0sbniMKuq9AlXF08kLWuyZgX
O3EJcuVgGjxS2gsVtgda74d+54fl1slkRV+T3YxYOtqe2kJcxLJx7gO4wfoM5OaC
4l2Hs3sRARSL005rUndoSMP/6uHmnw==
=+pUx
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=aAlp
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2020-07-06' into devicetree/next
Maxime Ripard introduces two new clock providers into RPi4's device tree:
- The first one based on the enhancements made to clk-raspberrypi, which
is now registered trough DT and provides control over the whole range
of firmware based clocks.
- The second one based on the new clk-bcm2711-dvp driver, which gates
the clocks and reset signals that feed into RPi4's HDMI0/1 blocks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix dtschema validator warnings like:
l2-cache@22000: $nodename:0:
'l2-cache@22000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
All those devices use standard BCM53011 (rev 5) or BCM53012 (rev 0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The hardware codec on the A10, A10s, A13 and A20 needs buffer in the
first 256MB of RAM. This was solved by setting the CMA pool at a fixed
address in that range.
However, in recent kernels there's something else that comes in and
reserve some range that end up conflicting with our default pool
requirement, and thus makes its reservation fail.
The video codec will then use buffers from the usual default pool,
outside of the range it can access, and will fail to decode anything.
Since we're only concerned about that 256MB, we can however relax the
allocation to just specify the range that's allowed, and not try to
enforce a specific address.
Fixes: 5949bc5602 ("ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes")
Fixes: 9604320101 ("ARM: dts: sun5i: Add Video Engine and reserved memory nodes")
Fixes: c2a641a748 ("ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200704130829.34297-1-maxime@cerno.tech
Remove the regulators node entirely because its children do not have any
unit addresses. This fixes DTC warning:
Warning (simple_bus_reg): /regulators/regulator-0: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Audio Graph Card is using "audio-graph-card" prefix instead of
"simple-graph-card", and moreover "widgets / routing" doesn't need it.
This patch removes unsupported "simple-graph-card" prefix from
motorola-mapphone-common.dtsi and vendor-prefixes.yaml.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/87r1ub39hq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead, expose the key via the input framework, as SW_MACHINE_COVER
The chip-detect GPIO is actually detecting if the cover is closed.
Technically it's possible to use the SD card with open cover. The
only downside is risk of battery falling out and user being able
to physically remove the card.
The behaviour of SD card not being available when the device is
open is unexpected and creates more problems than it solves. There
is a high chance, that more people accidentally break their rootfs
by opening the case without physically removing the card.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Link: https://lore.kernel.org/r/20200612125402.18393-3-merlijn@wizzup.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix dtschema validator warnings like:
l2-cache-controller@c4200000: $nodename:0:
'l2-cache-controller@c4200000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200626080626.4080-1-krzk@kernel.org
The BeagleBoard.org PocketBeagle has P1 and P2 headers [0] which expose
many of the TI AM3358 SoC balls to stacking expansion boards called
"capes", or to other external connections like jumper wires connected
to a breadboard.
Note: the AM3358 die is actually embedded inside of the OSD335x-SM
System-in-Package (SiP) [1] but that is irrelevant to the gpio driver.
Many of the P1 and P2 header pins can muxed to a GPIO line. The
gpio-line-names describe which P1 or P2 pin that line goes to and the
default mux for that P1 or P2 pin if it is not GPIO.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P1 or P2 pin is connected to a
GPIO line. The output of gpioinfo on a PocketBeagle would be:
gpiochip0 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "P1.08 [SPI0_CLK]" unused input active-high
line 3: "P1.10 [SPI0_MISO]" unused input active-high
line 4: "P1.12 [SPI0_MOSI]" unused input active-high
line 5: "P1.06 [SPI0_CS]" unused input active-high
line 6: "[MMC0_CD]" "cd" input active-low [used]
line 7: "P2.29 [SPI1_CLK]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "P1.26 [I2C2_SDA]" unused input active-high
line 13: "P1.28 [I2C2_SCL]" unused input active-high
line 14: "P2.11 [I2C1_SDA]" unused input active-high
line 15: "P2.09 [I2C1_SCL]" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "P2.31 [SPI1_CS]" unused input active-high
line 20: "P1.20 [PRU0.16]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "P2.03" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P1.34" unused input active-high
line 27: "P2.19" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "P2.05 [UART4_RX]" unused input active-high
line 31: "P2.07 [UART4_TX]" unused input active-high
gpiochip1 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[NC]" unused input active-high
line 6: "[NC]" unused input active-high
line 7: "[NC]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "P2.25 [SPI1_MOSI]" unused input active-high
line 10: "P1.32 [UART0_RX]" unused input active-high
line 11: "P1.30 [UART0_TX]" unused input active-high
line 12: "P2.24" unused input active-high
line 13: "P2.33" unused input active-high
line 14: "P2.22" unused input active-high
line 15: "P2.18" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "P2.01 [PWM1A]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "P2.10" unused input active-high
line 21: "[USR LED 0]" "beaglebone:green:usr0" output active-high [used]
line 22: "[USR LED 1]" "beaglebone:green:usr1" output active-high [used]
line 23: "[USR LED 2]" "beaglebone:green:usr2" output active-high [used]
line 24: "[USR LED 3]" "beaglebone:green:usr3" output active-high [used]
line 25: "P2.06" unused input active-high
line 26: "P2.04" unused input active-high
line 27: "P2.02" unused input active-high
line 28: "P2.08" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P2.20" unused input active-high
line 1: "P2.17" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[EEPROM_WP]" unused input active-high
line 6: "[SYSBOOT]" unused input active-high
line 7: "[SYSBOOT]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "[SYSBOOT]" unused input active-high
line 13: "[SYSBOOT]" unused input active-high
line 14: "[SYSBOOT]" unused input active-high
line 15: "[SYSBOOT]" unused input active-high
line 16: "[SYSBOOT]" unused input active-high
line 17: "[SYSBOOT]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "[NC]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "P2.35 [AIN5]" unused input active-high
line 23: "P1.02 [AIN6]" unused input active-high
line 24: "P1.35 [PRU1.10]" unused input active-high
line 25: "P1.04 [PRU1.11]" unused input active-high
line 26: "[MMC0_DAT3]" unused input active-high
line 27: "[MMC0_DAT2]" unused input active-high
line 28: "[MMC0_DAT1]" unused input active-high
line 29: "[MMC0_DAT0]" unused input active-high
line 30: "[MMC0_CLK]" unused input active-high
line 31: "[MMC0_CMD]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[I2C0_SDA]" unused input active-high
line 6: "[I2C0_SCL]" unused input active-high
line 7: "[JTAG]" unused input active-high
line 8: "[JTAG]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "P1.03 [USB1]" unused input active-high
line 14: "P1.36 [PWM0A]" unused input active-high
line 15: "P1.33 [PRU0.1]" unused input active-high
line 16: "P2.32 [PRU0.2]" unused input active-high
line 17: "P2.30 [PRU0.3]" unused input active-high
line 18: "P1.31 [PRU0.4]" unused input active-high
line 19: "P2.34 [PRU0.5]" unused input active-high
line 20: "P2.28 [PRU0.6]" unused input active-high
line 21: "P1.29 [PRU0.7]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#71_Expansion_Header_Connectors
[1] https://octavosystems.com/app_notes/osd335x-family-pin-assignments/
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BeagleBone Black has P8 and P9 headers [0] which expose many of the
AM3358 ZCZ SoC balls to stacking expansion boards called "capes", or to
other external connections like jumper wires connected to a breadboard.
BeagleBone users will often refer to the "Cape Exanpsion Headers" pin
diagram [1] as it is in the "Bone101" getting started tutorial. [2]
Most of the P8 and P9 header pins can muxed to a GPIO line. The
gpio-line-names describe which P8 or P9 pin that line goes to and the
default mux for that P8 or P9 pin if it is not GPIO.
For example, gpiochip 1 line 0 is connected to P8 header pin 25 (P8_25)
however the default device tree has the corresponding BGA ball (ZCZ U7)
muxed to mmc1_dat0 as it is used for the on-board eMMC chip. For that
GPIO line to be used, one would need to modify the device tree to
disable the eMMC and change the pin mux for that ball to GPIO mode.
Some of the AM3358 ZCZ balls corresponding to GPIO lines are not routed
to a P8 or P9 header, but are instead wired to some peripheral device
like on-board eMMC, HDMI framer IC, or status LEDs. Those names are in
brackets to denote those GPIO lines can not be used.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P8 or P9 pin is connected to a
GPIO line. The output of gpioinfo on a BeagleBone Black would be:
gpiochip0 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "P9_22 [spi0_sclk]" unused input active-high
line 3: "P9_21 [spi0_d0]" unused input active-high
line 4: "P9_18 [spi0_d1]" unused input active-high
line 5: "P9_17 [spi0_cs0]" unused input active-high
line 6: "[sd card]" "cd" input active-low [used]
line 7: "P9_42A [ecappwm0]" unused input active-high
line 8: "P8_35 [hdmi]" unused input active-high
line 9: "P8_33 [hdmi]" unused input active-high
line 10: "P8_31 [hdmi]" unused input active-high
line 11: "P8_32 [hdmi]" unused input active-high
line 12: "P9_20 [i2c2_sda]" unused input active-high
line 13: "P9_19 [i2c2_scl]" unused input active-high
line 14: "P9_26 [uart1_rxd]" unused input active-high
line 15: "P9_24 [uart1_txd]" unused input active-high
line 16: "[ethernet]" unused input active-high
line 17: "[ethernet]" unused input active-high
line 18: "[usb]" unused input active-high
line 19: "[hdmi]" unused input active-high
line 20: "P9_41B" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_19 [ehrpwm2a]" unused input active-high
line 23: "P8_13 [ehrpwm2b]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P8_14" unused input active-high
line 27: "P8_17" unused input active-high
line 28: "[ethernet]" unused input active-high
line 29: "[ethernet]" unused input active-high
line 30: "P9_11 [uart4_rxd]" unused input active-high
line 31: "P9_13 [uart4_txd]" unused input active-high
gpiochip1 - 32 lines:
line 0: "P8_25 [emmc]" unused input active-high
line 1: "[emmc]" unused input active-high
line 2: "P8_5 [emmc]" unused input active-high
line 3: "P8_6 [emmc]" unused input active-high
line 4: "P8_23 [emmc]" unused input active-high
line 5: "P8_22 [emmc]" unused input active-high
line 6: "P8_3 [emmc]" unused input active-high
line 7: "P8_4 [emmc]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "P8_12" unused input active-high
line 13: "P8_11" unused input active-high
line 14: "P8_16" unused input active-high
line 15: "P8_15" unused input active-high
line 16: "P9_15A" unused input active-high
line 17: "P9_23" unused input active-high
line 18: "P9_14 [ehrpwm1a]" unused input active-high
line 19: "P9_16 [ehrpwm1b]" unused input active-high
line 20: "[emmc]" unused input active-high
line 21: "[usr0 led]" "beaglebone:green:heartbeat" output active-high [used]
line 22: "[usr1 led]" "beaglebone:green:mmc0" output active-high [used]
line 23: "[usr2 led]" "beaglebone:green:usr2" output active-high [used]
line 24: "[usr3 led]" "beaglebone:green:usr3" output active-high [used]
line 25: "[hdmi]" "interrupt" input active-high [used]
line 26: "[usb]" unused input active-high
line 27: "[hdmi audio]" "enable" output active-high [used]
line 28: "P9_12" unused input active-high
line 29: "P8_26" unused input active-high
line 30: "P8_21 [emmc]" unused input active-high
line 31: "P8_20 [emmc]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P9_15B" unused input active-high
line 1: "P8_18" unused input active-high
line 2: "P8_7" unused input active-high
line 3: "P8_8" unused input active-high
line 4: "P8_10" unused input active-high
line 5: "P8_9" unused input active-high
line 6: "P8_45 [hdmi]" unused input active-high
line 7: "P8_46 [hdmi]" unused input active-high
line 8: "P8_43 [hdmi]" unused input active-high
line 9: "P8_44 [hdmi]" unused input active-high
line 10: "P8_41 [hdmi]" unused input active-high
line 11: "P8_42 [hdmi]" unused input active-high
line 12: "P8_39 [hdmi]" unused input active-high
line 13: "P8_40 [hdmi]" unused input active-high
line 14: "P8_37 [hdmi]" unused input active-high
line 15: "P8_38 [hdmi]" unused input active-high
line 16: "P8_36 [hdmi]" unused input active-high
line 17: "P8_34 [hdmi]" unused input active-high
line 18: "[ethernet]" unused input active-high
line 19: "[ethernet]" unused input active-high
line 20: "[ethernet]" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_27 [hdmi]" unused input active-high
line 23: "P8_29 [hdmi]" unused input active-high
line 24: "P8_28 [hdmi]" unused input active-high
line 25: "P8_30 [hdmi]" unused input active-high
line 26: "[emmc]" unused input active-high
line 27: "[emmc]" unused input active-high
line 28: "[emmc]" unused input active-high
line 29: "[emmc]" unused input active-high
line 30: "[emmc]" unused input active-high
line 31: "[emmc]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "[ethernet]" unused input active-high
line 3: "[ethernet]" unused input active-high
line 4: "[ethernet]" unused input active-high
line 5: "[i2c0]" unused input active-high
line 6: "[i2c0]" unused input active-high
line 7: "[emu]" unused input active-high
line 8: "[emu]" unused input active-high
line 9: "[ethernet]" unused input active-high
line 10: "[ethernet]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "[usb]" unused input active-high
line 14: "P9_31 [spi1_sclk]" unused input active-high
line 15: "P9_29 [spi1_d0]" unused input active-high
line 16: "P9_30 [spi1_d1]" unused input active-high
line 17: "P9_28 [spi1_cs0]" unused input active-high
line 18: "P9_42B [ecappwm0]" unused input active-high
line 19: "P9_27" unused input active-high
line 20: "P9_41A" unused input active-high
line 21: "P9_25" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://git.io/JfgOd
[1] https://beagleboard.org/capes
[1] https://beagleboard.org/Support/bone101
[2] https://beagleboard.org/static/images/cape-headers.png
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add gpio-ranges properties to the gpio controller nodes.
These gpio-ranges were created based on "Table 9-10. CONTROL_MODULE
REGISTERS" in the "AM335x Technical Reference Manual" [0] and "Table
4-2. Pin Attributes" in the "AM335x Sitara Processor datasheet" [1].
A csv file with this data is available for reference [2].
These mappings are valid for all SoC's that are using am33xx-l4.dtsi.
In addition, the only TI AM33xx parts that actually exist are [0]:
AM3351, AM3352, AM3354, AM3356, AM3357, AM3358, AM3359
These gpio-ranges properties should be added as they describe the
relationship between a gpio line and pin control register that exists
in the hardware. For example, GPMC_A0 pin has mode 7 which is labeled
gpio1_16. conf_gpmc_a0 register is at offset 840h which makes it pin 16.
[0] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
[1] http://www.ti.com/lit/ds/symlink/am3358.pdf
[2] https://gist.github.com/pdp7/6ffaddc8867973c1c3e8612cfaf72020
[3] http://www.ti.com/processors/sitara-arm/am335x-cortex-a8/overview.html
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU and DSP remote processors use sub-mailbox nodes only from a
limited set of System Mailboxes 5 and 6 to achieve the Remote Processor
Messaging (RPMsg) communication stack between the MPU host processor
and the respective remote processor. These are all defined and enabled
through the inherited common dra74-ipu-dsp-common.dtsi file.
The other System Mailboxes do not define any actual sub-mailboxes, so
they serve no purpose and can all be safely dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Assign the previously added CMA reserved memory nodes to the respective
IPU and DSP rproc device nodes, and enable these rproc nodes so that
these remote processors can be booted on the AM5729 BeagleBone AI board.
The addresses and sizes of the CMA pools are identical to those used on
various other TI AM572x/AM574x based boards. The mailboxes, timers and
watchdog-timers for all these remoteprocs are inherited by including the
common dra72-ipu-dsp-common.dtsi file.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dtschema validator warnings like:
l2-cache-controller@48242000: $nodename:0: 'l2-cache-controller@48242000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dtschema validator warnings like:
l2-cache-controller@48242000: $nodename:0:
'l2-cache-controller@48242000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various OMAP3 boards have two AES blocks, but only one is currently
available, because the hwmods are only configured for one.
This patch migrates the hwmods for the AES engine to sysc-omap2
which allows the second AES crypto engine to become available.
omap-aes 480a6000.aes1: OMAP AES hw accel rev: 2.6
omap-aes 480a6000.aes1: will run requests pump with realtime priority
omap-aes 480c5000.aes2: OMAP AES hw accel rev: 2.6
omap-aes 480c5000.aes2: will run requests pump with realtime priority
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to disable both aes_targets on hs boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP developers are particularly active at hunting down regressions,
so this is a separate branch with OMAP specific fixes for the v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks like
I only tested suspend and resume before dropping the legacy platform
data, and forgot to test it after dropping it. Turns out the main issue
was that we no longer have platform code calling pm_runtime_suspend
for DSS like we did for the legacy platform data case, and that fix
is still being discussed on the dri-devel list and will get merged
separately. The DSS related testing exposed a pile other other display
related issues that also need fixing though":
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=FFTv
-----END PGP SIGNATURE-----
Merge tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM OMAP fixes from Arnd Bergmann:
"The OMAP developers are particularly active at hunting down
regressions, so this is a separate branch with OMAP specific
fixes for v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks
like I only tested suspend and resume before dropping the legacy
platform data, and forgot to test it after dropping it. Turns out
the main issue was that we no longer have platform code calling
pm_runtime_suspend for DSS like we did for the legacy platform data
case, and that fix is still being discussed on the dri-devel list
and will get merged separately. The DSS related testing exposed a
pile other other display related issues that also need fixing
though":
- Fix ti-sysc optional clock handling and reset status checks for
devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested to
avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process"
* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
...
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7zM08UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5HNAf+Kw6EPNxYom/MJ4P92gxLAtPA6AO4
+WuLYmSphhgmGAQLFU4UiTH/2sYXmT7fSDwLhfZI5XJp6j8J89Hxe2kyMomvIT92
Xbbzp7fr+2FPGgyI6ImiKTFeSZiT0LPq5fs1uF2lTP6+/SklF9yy5ynUvNULrD4b
iSAXOZkMz6Ft8dn1zYrTKPIYfsTe1zXsDgw8a9sc+0LfgiR5cBTq359jHrN5Q0Tq
NYoOHT+8V5C8BVmzp5I1zoghZEayPT2Ui1JIwBiyVij8KqZvYY3wckjPqgdfQ1vK
IzGksPWRojKAw2RKA59kpUR/pgoZH3GYnfjmCAIOkMnMSgAqz1inZZq2oA==
=iERQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8:
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
* tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
Link: https://lore.kernel.org/r/20200624111725.GA24312@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
-----BEGIN PGP SIGNATURE-----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=SUaO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
* tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Correct FA2 mailbox node
ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
Link: https://lore.kernel.org/r/20200619202250.19029-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
-----BEGIN PGP SIGNATURE-----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=Hqfw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Few dts fixes for omaps for v5.8
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
* tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Link: https://lore.kernel.org/r/pull-1592499282-121092@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
-----BEGIN PGP SIGNATURE-----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=UNki
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Missed sdhci patch for am3 and am4
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
* tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driver
Link: https://lore.kernel.org/r/pull-1591637467-607254@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl7iS6oRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXPLLBAAzcABBnwfnk+vjSHJ9QnQ/9LfJTLUIrkH
ZpB/CR6VC86STjpePaNpVN/fm5sODN4zvtpsuAvJgyF+9Hp3GRPxglC4g9cAmU8x
VFQepzgOLOQ/ubPesVWa14RgAoK29GNvfzihCKGmhOq7kz7I/PDIQr8txjw8KHqV
M8oVefWL6l95z1MwVEKvsebyloBwYx9q/+Q5bipoV/GvrQnMjaCFzEaO6n8nH0Xc
T6XsKA+4hCr94tHM3jgfSdIQYFrq38H84t986ExMVfIhh3LfNkNu7CrSIWcjTgEY
jAs/hnPQ/JzMuBivweCrfkpQYy4D/GOjueQJy2Mf3deMJUWEsgZzMOML743W307j
HvGB5c3i1HgXir6PtjQFP4RqQQpQN1b4xjYEgvd8SB6xnrbdP43YsNrm9gnqbWd8
yNqiY2+uEh7OFyOJe0Ikrr1DNh3K0dSmtqrdhtWor165W0sAqlgjFjrjH1/xcQrN
XWhjBCl/NAODNZqbxU4l6rjiSU8J0cGr8wJrZNLe4itZy9R2jPInTv8FSpfcNI32
cVdDfPc4SVl8zsfZq4vhDrS/JVG7Sp/DXXQIG04wMlA6vyK4YAHh0U40121aAE8E
AwzOh++cCeZPQB+i3qCkRMLDohC7IJVvZZ/KN1mp43dDEW+epx5tct0ZmfElr4uX
Vg84CHL/I28=
=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
-----BEGIN PGP SIGNATURE-----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=2f3w
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARMv8 Juno/Vexpress/Fast Models fix for v5.8
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
* tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Move mcc node back into motherboard node
Link: https://lore.kernel.org/r/20200609180447.GB5732@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PDMIC needs PDM microphones to work. sama5d2 xplained doesn't have
such microphones, so there is no reason to enable PDMIC and take the
pins since there is no-one using them.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200618152845.682723-1-codrin.ciubotariu@microchip.com
Fix dtschema warning message by changing nodename to 'cache-controller':
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/l2c2x0.yaml
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: l2-cache-controller@10502000:
$nodename:0: 'l2-cache-controller@10502000' does not match '
^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The SDHCI on Tegra30 is in fact not backwards-compatible with the
instantiation found on earlier SoCs. Drop the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra30 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was probably left there by mistake or perhaps was a typo in the
first place. Remove it.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI output needs to specify a parent clock that will be used to
drive both the output and the display controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Seaboard uses a non-existing, possibly obsoleted, binding for the
battery. Move to the standard binding which seems to be a super-
set of the odl binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unit-addresses should be numeric. This fixes a validation failure seen
using the json-schema tooling.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simple panels can only have a single power supply. The second listed
supply is not needed because it is also the input supply of the first
supply and therefore will always be on at the same time.
In retrospect the panel probably doesn't qualify as simple since it
apparently does need both of these supplies, even if in the case of the
Medcom Wide it isn't necessary to explicitly hook them up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use commas rather than underscores to separate the various parts of the
unit-address in CPU OPPs to make them properly validate under the json-
schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is purely to make the json-schema validation tools happy because
they cannot deal with string arrays that may be in arbitrary order.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory controller exposes a set of memory client resets and needs to
specify the #reset-cells property in order to advertise the number of
cells needed to describe each of the resets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.
While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ethernet device should be named "ethernet@<unit-address>".
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Audio codecs need a #sound-dai-cells property, so add one to the audio
codecs on various Tegra-based boards that don't have one.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI controller instantiated on Tegra114 is not backwards-
compatible with the version on Tegra30, so remove the corresponding
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent clocks are determined by the output that will be used, not by
the display controller that drives the output. On previous generations a
simple RGB output used to be part of the display controller and hence an
explicit parent clock needed to be assigned to the display controller to
drive the RGB output. Starting with Tegra124, that RGB output has been
dropped and the parent clock can therefore be removed from the display
controller device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra114 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr3d in Tegra114 is not backwards-compatible with
the version found on earlier chips. Remove the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr2d in Tegra114 is not backwards-compatible with
the version found on earlier chips. While the hardware IP is identical,
the compatible string also describes the integration of the IP, which
in the case of Tegra114 is slightly different in that it's part of the
HEG power partition, whereas it wasn't previously.
Drop the misleading compatible string so that drivers that support the
older integrations cannot match on it. Since they wouldn't be able to
control the power partition, such driver wouldn't be able to access any
of the registers of the IP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x device tree bindings require the clock- and interrupt-names
properties to be present, so add them where missing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the regulators at the top
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra SDHCI controller bindings state that the clock-names property
is required, so add the missing properties on Tegra114.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.
To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The L1 and L3 lines drive NMOS transistors that are OFF with a low level.
On the SAM9X60 EK board, if the pins corresponding to L1 and L3
have pull-ups enabled, there is an extra 2 x 30uA power consumption.
Use pull-downs for these 2 lines to remove the unnecessary power
consumption.
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615095525.43414-2-codrin.ciubotariu@microchip.com
The R1 and R3 lines drive NMOS transistors that are OFF with a low level.
On the SAMA5D2 Xplained board, if the pins corresponding to R1 and R3
have pull-ups enabled, there is an extra 2 x 30uA power consumption.
Use pull-downs for these 2 lines to remove the unnecessary power
consumption.
Fixes: b133ca7a65 ("ARM: dts: at91: sama5d2_xplained: add pin muxing and enable classd")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615095525.43414-1-codrin.ciubotariu@microchip.com
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d5171723 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Veyron Jaq and Mighty both use the Marvel 8897 WiFi+BT chip. Add wakeup
and pinctrl block to devicetree so the btmrvl driver can correctly
configure the wakeup interrupt.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200612130219.v2.1.I66864be898aa835ccb66b6cd5220d0b082338a81@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3288-tinker.dt.yaml: tsadc: otp-gpio:
{'phandle': [[54]], 'rockchip,pins': [[0, 10, 0, 118]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for
RGMII mode") the networking is broken on the BeagleBone AI which has
the AR8035 PHY for Gigabit Ethernet [0]. The fix is to switch from
phy-mode = "rgmii" to phy-mode = "rgmii-rxid".
Note: Grygorii made a similar DT fix for other AM57xx boards with a
different phy in commit 820f8a870f ("ARM: dts: am57xx: fix networking
on boards with ksz9031 phy").
[0] https://git.io/Jf7PX
Fixes: 520557d485 ("ARM: dts: am5729: beaglebone-ai: adding device tree")
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I accidentally flipped the system timer to use system clock instead of
the 32k source clock.
Fixes: 14b1925a72 ("ARM: dts: Configure system timers for omap4")
Signed-off-by: Tony Lindgren <tony@atomide.com>
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pwr and status leds configuration and turn on pwr led by default for Orange
Pi Zero Plus 2 (both H3 and H5 variants).
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-2-diego.rondini@kynetics.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable support for USB OTG port on Orange Pi Zero Plus 2 (both H3 and H5
variants). As, according to the board schematics, the USB OTG port cannot
provide power to external devices, we set dr_mode to peripheral.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-1-diego.rondini@kynetics.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently the PL330 is enabled by default. However if left in IDM reset, as is
the case with the Meraki and Synology NSP devices, the system will hang when
probing for the PL330's AMBA peripheral ID. We therefore should be able to
disable it in these cases.
The PL330 is also included among of the list of peripherals put into coherent
mode, so "dma-coherent" has been added here as well.
Fixes: 5fa1026a3e ("ARM: dts: NSP: Add PL330 support")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add sleep and idle states to uart4 pin configuration.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add sleep and idle states to uart4 pin configuration.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Sleep pin configuration is refined for low power modes:
- "sleep" (no wakeup & console suspend enabled): put pins in analog state
to optimize power
- "idle" (wakeup capability): keep Rx pin in alternate function
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the missing #address-cells and #size-cells to spi node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fix the nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rename pwm pinctrl nodes name to matching with yaml bindings
requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable the stmpe811 touch screen on stm32429-disco board.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for I2C3 controller on
stm32f4.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds I2C3 instances of the STM32F429 SoC
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for ltdc and spi5 controller
on stm32f429-disco board.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable spi5's dma configuration for graphics data output to
ilitek ili9341 panel via mipi dbi interface.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the camera daughter board which is connected to
iWave's RZ/G1H Qseven carrier board. Also enable ttySC[0135] and
ethernet1 interfaces.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1591552659-21314-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add sound support for the RZ/G1H SoC (a.k.a. R8A7742).
This work is based on similar work done on the R8A7744 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1590526904-13855-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe internal PCI bridge devices, USB phy device and
link PCI USB devices to USB phy.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1590356277-19993-7-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP support.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1589555337-5498-16-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the I2C[0-3] and IIC[0-3] device nodes to the R8A7742 device tree.
Automatic transmission for PMIC control is not available on IIC3 hence
compatible strings "renesas,rcar-gen2-iic" and "renesas,rmobile-iic" are
not added to iic3 node.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1589555337-5498-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are several issues with the bluetooth node - the wrong
compatible was used (because the bcm4329 compatible didn't exist
when the node was added), the max rate was incorrect (due to
limitations in the samsung TTY driver which have now been fixed),
the clocks were not assigned properly so some rates didn't work,
and the some pinctrl settings weren't explicitly set. Fix all
of the above issues.
While we're at it, update from the deprecated host-wakeup-gpios
property to the host-wake interrupt.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a BMA023 accelerometer attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Correct the fuelgauge definition because only the fuelgauge on
fascinate4g has interrupt support (and even then it was wrong).
Also, assign the GPIO pinctrl so the interrupt is properly configured
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The GPH3 pins on s5pv210 have interrupt support and had the
interrupt-cells property but was missing the interrupt-controller
property.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM4354 Bluetooth chip on the serial bus #0 on
the Exynos3250-based Artik5 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Exynos5422/5800 the regulator supply for the A15 cores ("vdd_arm") is
coupled with the regulator supply for the SoC internal circuits
("vdd_int"), thus all operating points that modify one of those supplies
have to specify a triplet of the min/target/max values to properly work
with regulator coupling.
Fixes: eaffc4de16 ("ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox nodes defined in various dts files have been moved to
common dra7-ipu-dsp-common.dtsi and dra74-ipu-dsp-common.dtsi files
in commit a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes
into common files"), but the nodes were erroneously left out in the
dra7-evm-common.dtsi file. Fix this by removing these duplicate nodes.
Fixes: a11a2f73b3 ("ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries
for IPU/DSP timers") was added to allow the OMAP clocksource timer
driver to use the clock aliases when reconfiguring the parent clock
source for the timer functional clocks after the timer_sys_ck clock
aliases got cleaned up in commit a8202cd517 ("clk: ti: dra7: drop
unnecessary clock aliases").
The above patch however has missed adding the entries for couple of
timers (14, 15 and 16), and also added erroneously in the parent
ti-sysc nodes for couple of clocks (timers 4, 5 and 6). Fix these
properly, so that any of these timers can be used with OMAP remoteproc
IPU and DSP devices. The always-on timers 1 and 12 are not expected
to use this clock source, so they are not modified.
Fixes: 5390130f3b ("ARM: dts: dra7: add timer_sys_ck entries for IPU/DSP timers")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Figure 16-23 define sysconfig register and soft_reset
are in first position corresponding to SYSC_OMAP4_SOFTRESET defined
in ti-sysc.h.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x TRM: Table 2-1 defines USBSS - USB Queue Manager in memory region
0x4740 0000 to 0x4740 7FFF.
Looks like the older TRM revisions list the range from 0x5000 to 0x8000
as reserved.
Fixes: 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Oskar Holmlund <oskar@ohdata.se>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Commit d9258898ad ("arm64: dts: arm: vexpress: Move fixed devices
out of bus node") moved the "mcc" DT node into the root node, because
it does not have any children using "reg" properties, so does violate
some dtc checks about "simple-bus" nodes.
However this broke the vexpress config-bus code, which walks up the
device tree to find the first node with an "arm,vexpress,site" property.
This gave the wrong result (matching the root node instead of the
motherboard node), so broke the clocks and some other devices for
VExpress boards.
Move the whole node back into its original position. This re-introduces
the dtc warning, but is conceptually the right thing to do. The dtc
warning seems to be overzealous here, there are discussions on fixing or
relaxing this check instead.
Link: https://lore.kernel.org/r/20200603162237.16319-1-andre.przywara@arm.com
Fixes: d9258898ad ("arm64: dts: vexpress: Move fixed devices out of bus node")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place
-----BEGIN PGP SIGNATURE-----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=FFm0
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
We can currently sometimes get "RXS timed out" errors and "EOT timed out"
errors with spi transfers.
These errors can be made easy to reproduce by reading the cpcap iio
values in a loop while keeping the CPUs busy by also reading /dev/urandom.
The "RXS timed out" errors we can fix by adding spi-cpol and spi-cpha
in addition to the spi-cs-high property we already have.
The "EOT timed out" errors we can fix by increasing the spi clock rate
to 9.6 MHz. Looks similar MC13783 PMIC says it works at spi clock rates
up to 20 MHz, so let's assume we can pick any rate up to 20 MHz also
for cpcap.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a
1U rackmount router based on the IPQ8064, supporting the serial UART,
dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED
device.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/75390e66c9e6e36ddd42dc7f54cac28dfd7a24b9.1589824955.git.noodles@earth.li
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The device node name should reflect generic class of a device so rename
the "msmram" node and its children to "sram". This will be also in sync
with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IhYQUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5Bvwf8Cy/gm3ezs2OmjtdF3jql86qo7tqk
nUwPDnRhlPYInN8yKlipMsYn2yupCPSwENGYwxLculwsHyQ7RNEI8a1jY2zEkdh9
+IoZCNeOxOk40iQoCtaxBAJVz73BY8ptdKgfKL44xQ32e4oVQrgw1iAPdNS60yzl
5TRXxghYnfeRC5c7ZKKEF0X74RzWb/zwEWAcs3yczuPzQGAtcBmYTG8b/y+/HNT0
oTTcnN+clw48xAPuq6/8nMseVMLqTzyyBQpn/TI78LWGfBtaTIv6l7pjZBquhSGi
+QYKHgbC3POv8TYWGu+csqFfQvbfeiO/HEHFKPcvJ8O+QoRMB9nvejn42Q==
=I7h9
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.8:
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
* tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
ARM: dts: imx53-cx9020: Group port definitions for the dvi-converter
ARM: dts: imx5: make src node name generic
ARM: dts: imx50: Add src node interrupt
ARM: dts: imx: make src node name generic
ARM: dts: imx7d-pinfunc: add input mux for ENET2 mdio
ARM: dts: imx6sl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl-gw5910: fix wlan regulator
ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
ARM: dts: imx53: Add src node interrupt
ARM: dts: imx51: Add src node interrupt
ARM: dts: imx50: Remove unused iomuxc-gpr node
ARM: dts: imx6qdl-gw552x: add USB OTG support
ARM: dts: imx6-sr-som: add ethernet PHY configuration
arm: dts: ls1021atwr: Add QSPI node properties
ARM: dts: e60k02: add interrupt for PMIC
ARM: dts: colibri: introduce device trees with UHS-I support
ARM: dts: imx7d: Add cpu1 supply
...
Link: https://lore.kernel.org/r/20200523032516.11016-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- eth PHY and USB PHY updates
-----BEGIN PGP SIGNATURE-----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=H41z
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.8
- eth PHY and USB PHY updates
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: Switch existing boards with RGMII PHY to "rgmii-id"
ARM: dts: meson: Add the Ethernet "timing-adjustment" clock
ARM: dts: meson8m2: Use the Meson8m2 specific USB2 PHY compatible
ARM: dts: meson: add the gadget mode properties to the USB0 controller
Link: https://lore.kernel.org/r/5ec6f524.1c69fb81.b979a.ae15@mx.google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl68I9MRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXO2/Q/+IiBtpAgZ1Y5XCXjfmBOGF5H5DKtSK7xd
pOVqkRq6N0akGOuwLWaI9CHoJnEZ1VUMQZzBbZjCia640BeGvyM7rEs8ffCmvlqa
aLRwDAV3+mg0D4M5TyElLqAc5a3pNBDmOvyUCgXAql6wy2tLdkzC+P8K+LaFltPW
05j/jfLM5EOvfRPxX0xvz+qZYTiKeOw5GZosGz2MwRAemSFy5EWm9yTqyO+exJm3
IMWkdwR9TBgkf8FE+QhuhnVIS+VmXT5VVFgAEcYWCmAOjvbPONFeumjKJNxTEgpf
/IzuAE5FRr+d7OqPcHV8XFhsfw2NlyKmyqzdm+RTzV4RosmsU9c8rdkV/vqWfKbO
oVw5DHFT20jRRCcFGJp81yMaeo6KPPe8X5l+0/DeyC0ai4Vq/eQKlJaB3LOsYJSa
FUjyrCex8d2n2qQlkuXRCkIj259wPFtjFbgwQBzgYD33KEpOLlNseLMV3Qa8E63S
qCZTAQs2rlEjJgmdByZ38Pjcu+Rq/qhwG12+73oF8tQmoNf+VSKVrfbki4Q5Ne37
L8TvQFWODeE5aUu+MYRQKMDvMd6ufUtUDQLOSIO+pd0C5fDcaxUFT9kOvlM/zBW+
b2AcggtPOeNFtoJK7V2Z4IpnqSdZyX+sPpUPLRZZr0V21bw22Gw6WLu0izMdPqWE
mrzCYrDSy0k=
=tWSS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
-----BEGIN PGP SIGNATURE-----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=07SB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OiS0
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
-----BEGIN PGP SIGNATURE-----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=klA0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.
Then the EP child node are useless and describe as deprecated in the
documentation binding: remove all the nodes from the SoC device tree
file. Remove also the #address-cells and #size-cells properties that
are no longer needed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7Glo8UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5L1wf9ErUGnk73syGW6Hhr8VRRGocK8Zj7
Skh0E2k1ZT0YXRn5h6dikZw9TsR8IVt5CSt57NxvR61i4PnPm8PEBZdIl80kMu3P
3wO28Z4oIqhi9tzI+fM6uRV6WGxp5fIuwyEghAPpv0Xo/XKDbDQZkk/TtQDhqvVC
n7rjgk+N/x6kVTfRTYYIvI+XSoGM1lGdBl9DdAxKc2Suxr27qFcopYIE6JKsapoo
0khguE7v8BNG+N7iJ6tDXRcn4MV1TEDpTQ0cwZr1zIAiA3P5ZYKIGdweScVJ80fa
RGllUMBBrs7r0cNTpA8hu76omF2Kim0D8QsvLMDLELOijB4b/qBf2bU9AA==
=cAJG
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7, round 2:
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
* tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts/imx6q-bx50v3: Set display interface clock parents
Link: https://lore.kernel.org/r/20200521150719.GB24084@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These were queued for v5.7 as bugfixes, merge them
here as well to resolve the conflicts.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These three fixes should make it into linux-5.7 and
also into the branch for other mmp dt changes for v5.8,
so I created a branch for them.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"usb-nop-xceiv" is good enough if we don't lose the configuration done
by the firmware, but we'd really prefer a real driver.
Unfortunately, the PHY core is odd in that when the node is compatible
with "usb-nop-xceiv", it ignores the other compatible strings. Let's
just remove it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I've managed to get about everything wrong while digging these out of
OEM's board file.
Correct the bus numbers, the exact model of the NOR flash, polarity of
the chip selects and align the SPI frequency with the data sheet.
Tested that it works now, with a slight fix to the PXA SSP driver.
Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Clocks are in fact slightly different on MMP3. In particular, PLL2 is
fixed to a different frequency, there's an extra PLL3, and the GPU
clocks are configured differently.
Link: https://lore.kernel.org/r/20200419171157.672999-15-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's one extra SDHCI on MMP3, used by the internal SD card on OLPC
XO-4. Add it to the device tree.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The node name preferred by mmc-controller.yaml binding spec is "mmc":
berlin2-sony-nsz-gs7.dt.yaml: sdhci@ab0000: $nodename:0:
'sdhci@ab0000' does not match '^mmc(@.*)?$'
berlin2-sony-nsz-gs7.dt.yaml: sdhci@ab0800: $nodename:0:
'sdhci@ab0800' does not match '^mmc(@.*)?$'
berlin2-sony-nsz-gs7.dt.yaml: sdhci@ab1000: $nodename:0:
'sdhci@ab1000' does not match '^mmc(@.*)?$'
berlin2cd-google-chromecast.dt.yaml: sdhci@ab0000: $nodename:0:
'sdhci@ab0000' does not match '^mmc(@.*)?$'
berlin2cd-valve-steamlink.dt.yaml: sdhci@ab0000: $nodename:0:
'sdhci@ab0000' does not match '^mmc(@.*)?$'
berlin2q-marvell-dmp.dt.yaml: sdhci@ab0000: $nodename:0:
'sdhci@ab0000' does not match '^mmc(@.*)?$'
berlin2q-marvell-dmp.dt.yaml: sdhci@ab0800: $nodename:0:
'sdhci@ab0800' does not match '^mmc(@.*)?$'
berlin2q-marvell-dmp.dt.yaml: sdhci@ab1000: $nodename:0:
'sdhci@ab1000' does not match '^mmc(@.*)?$'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are better generic ones and the validation is going to complain:
mmp3-dell-ariel.dt.yaml: hsic@f0001000: $nodename:0: 'hsic@f0001000'
does not match '^usb(@.*)?'
mmp3-dell-ariel.dt.yaml: hsic@f0002000: $nodename:0: 'hsic@f0002000'
does not match '^usb(@.*)?'
...
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current one makes validation unhappy:
mmp3-dell-ariel.dt.yaml: l2-cache-controller@d0020000: $nodename:0:
'l2-cache-controller@d0020000' does not match
'^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This way the device tree validator learns that each cell of the property
constitutes a separate item. Otherwise it gets unnecessairly upset:
mmp3-dell-ariel.dt.yaml: rtc@d4010000: interrupts: [[1, 0]] is too short
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This way the device tree validator learns that each cell of the property
constitutes a separate item. Otherwise it gets unnecessairly upset:
pxa168-aspenite.dt.yaml: rtc@d4010000: interrupts: [[5, 6]] is too short
pxa910-dkb.dt.yaml: rtc@d4010000: interrupts: [[5, 6]] is too short
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpio-pxa uses two cell to encode the interrupt source: the pin number
and the trigger type. Adjust the device node accordingly.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This way the device tree validator learns that each cell of the property
constitutes a separate item. Otherwise it gets unnecessairly upset:
pxa300-raumfeld-speaker-s.dt.yaml: gpio@40e00000: interrupts:
[[8, 9, 10]] is too short
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr.>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpio-pxa uses two cell to encode the interrupt source: the pin number
and the trigger type. Adjust the device node accordingly.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This makes the nodes compatible with the generic i2c binding without the
board DTS files having to supply the necessary properties themselves.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current ones makes validation unhappy:
dove-d3plug.dt.yaml: main-interrupt-ctrl@20200: $nodename:0:
'main-interrupt-ctrl@20200' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current ones makes validation unhappy:
kirkwood-lsxhl.dt.yaml: main-interrupt-ctrl@20200: $nodename:0:
'main-interrupt-ctrl@20200' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various miscellaneous device tree source fixes to make them fully
binding compliant. It includes fixing various device node names,
order of interrupt properties, compatible names, address and size
cell fields and their aligment with children nodes as well as
moving some fixed devices out of bus node.
-----BEGIN PGP SIGNATURE-----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=Z5QL
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/Vexpress/Fast Models updates for v5.8
Various miscellaneous device tree source fixes to make them fully
binding compliant. It includes fixing various device node names,
order of interrupt properties, compatible names, address and size
cell fields and their aligment with children nodes as well as
moving some fixed devices out of bus node.
* tag 'juno-updates-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Fix SCPI shared mem node name
arm64: dts: vexpress: Fix VExpress LED names
arm64: dts: juno: Fix GPU interrupt order
arm64: dts: fvp/juno: Fix bus node names
arm64: dts: fvp: Fix SMMU DT node
arm64: dts: fvp/juno: Fix serial node names
arm64: dts: juno: Use proper DT node name for USB
arm64: dts: fvp: Fix ITS node names and #msi-cells
arm64: dts: fvp: Fix GIC child nodes
arm64: dts: juno: Fix GIC child nodes
arm64: dts: fvp: Fix GIC compatible names
arm64: dts: juno: Fix mem-timer
arm64: dts: juno: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed clocks out of bus node
arm64: dts: vexpress: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed devices out of bus node
arm64: dts: fvp/juno: Fix node address fields
Link: https://lore.kernel.org/r/20200519094702.GA32975@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board: Microchip SAMA5D2 Industrial Connectivity Platform
- All SoCs are now converted to the new PMC device tree binding
- sama5d2 flexcom nodes are now fully described in sama5d2.dtsi
-----BEGIN PGP SIGNATURE-----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=EQfX
-----END PGP SIGNATURE-----
Merge tag 'at91-5.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.8
- New board: Microchip SAMA5D2 Industrial Connectivity Platform
- All SoCs are now converted to the new PMC device tree binding
- sama5d2 flexcom nodes are now fully described in sama5d2.dtsi
* tag 'at91-5.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (35 commits)
ARM: dts: at91: sama5d2_xplained: Add aliases for the dedicated I2C IPs
ARM: dts: at91: Configure I2C SCL gpio as open drain
ARM: dts: at91: sama5d2_xplained: Describe the flx0 I2C function
ARM: dts: at91: sama5d2_ptc_ek: Add comments to describe the aliases
ARM: dts: at91: sama5d2_xplained: Add alias for DBGU
ARM: dts: at91: sama5d2: Add missing flexcom definitions
ARM: dts: at91: sama5d2: Remove i2s and tcb aliases from SoC dtsi
ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and I2C flx0 functions
ARM: dts: at91: sama5d2: Add DMA bindings for the flx1 I2C function
ARM: dts: at91: sama5d2: Add DMA bindings for the flx3 SPI function
ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions
ARM: dts: at91: sama5d2: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sama5d2: Move flx0 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx1 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx2 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx3 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx4 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
ARM: dts: at91: sama5d27_wlsom1: Add alias for i2c0
ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP
...
Link: https://lore.kernel.org/r/20200518212844.GA26356@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add proximity sensor and magnetometer to the Samsung Golden
devicetree.
- Add magnetometer and touchscreen to the Samsung Skomer
devicetree.
-----BEGIN PGP SIGNATURE-----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=UOo9
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.8 kernel series:
- Add proximity sensor and magnetometer to the Samsung Golden
devicetree.
- Add magnetometer and touchscreen to the Samsung Skomer
devicetree.
* tag 'ux500-dts-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500: Add touchscreen to the Skomer
ARM: dts: ux500: samsung-skomer: Add magnetometer
ARM: dts: ux500: samsung-golden: Add magnetometer
ARM: dts: ux500: samsung-golden: Add proximity sensor
Link: https://lore.kernel.org/r/CACRpkdbukO33SxAZ_yn-1N8=hq3hF5OBOtP_V0fbjRT-fAa87A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Leave the FPGA bridges disabled in base dtsi
- Add fpga2hps and fpga2sdram bridges on base Cyclone5/Arria5 dtsi
-----BEGIN PGP SIGNATURE-----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=UMA8
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_update_for_v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.8
- Leave the FPGA bridges disabled in base dtsi
- Add fpga2hps and fpga2sdram bridges on base Cyclone5/Arria5 dtsi
* tag 'socfpga_dts_update_for_v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add fpga2hps and fpga2sdram bridges
ARM: dts: socfgpa: set bridges status to disabled
Link: https://lore.kernel.org/r/20200515193029.11318-2-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
support, including:
- Support for the IOMMU on the H6
- Support for cpufreq / thermal throttling on the H6
- Support for the mailbox on the A64, A83t, H3, H5 and H6
- New boards: A20-OLinuXino-LIME-eMMC
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXr7NHgAKCRDj7w1vZxhR
xbhGAQCDavHkpjvq4Hwk/znoS0Y6NvW1JQUyKUWH8K6ah1ZkFwEA5gC0Ac9cbDAk
Q5fZeYl7mPbEL9DI0RphVqHmY2ezXw0=
=WR5/
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- Support for the IOMMU on the H6
- Support for cpufreq / thermal throttling on the H6
- Support for the mailbox on the A64, A83t, H3, H5 and H6
- New boards: A20-OLinuXino-LIME-eMMC
* tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (23 commits)
arm64: dts: allwinner: h6: Add IOMMU
arm64: dts: allwinner: h6: Enable CPU opp tables for Tanix TX6
arm64: dts: allwinner: h6: add voltage range to OPP table
arm64: dts: allwinner: sun50i-a64: Add missing address/size-cells
arm64: dts: allwinner: h6: Enable CPU opp tables for Pine H64
arm64: dts: allwinner: Sort Pine H64 device-tree nodes
arm64: dts: allwinner: h6: Enable CPU opp tables for Orange Pi 3
arm64: dts: allwinner: h6: Enable CPU opp tables for Beelink GS1
arm64: dts: allwinner: h6: Add CPU Operating Performance Points table
arm64: dts: allwinner: h6: Add thermal trip points/cooling map
arm64: dts: allwinner: h6: Add clock to CPU cores
arm64: allwinner: h6: orangepi-lite2: Support BT+WIFI combo module
arm64: dts: allwinner: h6: orangepi: Disable OTG mode
arm64: dts: allwinner: h6: orangepi: Add gpio power supply
ARM: dts: sun8i-h2-plus-bananapi-m2-zero: Fix led polarity
arm64: dts: allwinner: h6: Add msgbox node
arm64: dts: allwinner: a64: Add msgbox node
ARM: dts: sunxi: h3/h5: Add msgbox node
ARM: dts: sunxi: a83t: Add msgbox node
ARM: dts: sun8i-h3: add opp table for mali gpu
...
Link: https://lore.kernel.org/r/cfa66bd9-f74c-4614-9ea5-9ef8546cc571.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a bit of cleanup and CPU frequency scaling support for the
Tegra30 Beaver board.
-----BEGIN PGP SIGNATURE-----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=55XZ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.8-rc1
This contains a bit of cleanup and CPU frequency scaling support for the
Tegra30 Beaver board.
* tag 'tegra-for-5.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra30: beaver: Add CPU Operating Performance Points
ARM: dts: tegra30: beaver: Set up voltage regulators for DVFS
ARM: tegra: Kill off "simple-panel" compatibles
Link: https://lore.kernel.org/r/20200515145311.1580134-11-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5g8QAKCRCKwlD9ZEnx
cDusAQD4SCmyY0MZZNWQhkhu2ics2wYpKItw4Y7E4fl9XUlXkQEAyyN11vVNoteX
7KvNX7/9eXpberlcx4H6szPQsOzWzwM=
=2KDk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8 (take two)
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
ARM: dts: r8a7742: Add GPIO nodes
ARM: dts: r8a7742: Add [H]SCIF{A|B} support
ARM: dts: r8a7742: Add IRQC support
ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
ARM: dts: r8a7742: Initial SoC device tree
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-fix a typo for DAC io-channel-cells on f429 and h743
MPU part:
-Generic:
-Bump tp PSCI 1.0
-Fix a typo for DAC io-channel-cells
-Add M4 pdds for deep sleep mode
-Add I2C fatmode plus support
-Add new Octavio lxa-mc1 board based on OSDMP15x SiP
-Add new Stinger96 board support. It is a 96Boards IoT Extended board
based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
Onboard BG96 modem...
-Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
VOC sensor, 2 digitals microphones ...
-DH:
-Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
-Add GPIO led and GPIO keys support on PDK2 board
-AV96:
-Major rework to support official avenger96 board based on DHCOR SOM.
-Prototype board is no more supported
-----BEGIN PGP SIGNATURE-----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=JFtr
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.8, round 1
Highlights:
----------
MCU part:
-fix a typo for DAC io-channel-cells on f429 and h743
MPU part:
-Generic:
-Bump tp PSCI 1.0
-Fix a typo for DAC io-channel-cells
-Add M4 pdds for deep sleep mode
-Add I2C fatmode plus support
-Add new Octavio lxa-mc1 board based on OSDMP15x SiP
-Add new Stinger96 board support. It is a 96Boards IoT Extended board
based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
Onboard BG96 modem...
-Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
VOC sensor, 2 digitals microphones ...
-DH:
-Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
-Add GPIO led and GPIO keys support on PDK2 board
-AV96:
-Major rework to support official avenger96 board based on DHCOR SOM.
-Prototype board is no more supported
* tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (58 commits)
ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add IoT Box board support
dt-bindings: arm: stm32: Document IoT Box compatible
ARM: dts: stm32: Add Stinger96 board support
dt-bindings: arm: stm32: Document Stinger96 compatible
ARM: dts: stm32: Add missing pinctrl entries for STM32MP15
dt-bindings: Add vendor prefix for Shiratech Solutions
ARM: dts: stm32: Add bindings for SPI2 on AV96
ARM: dts: stm32: Add alternate pinmux for SPI2 pins
ARM: dts: stm32: Add bindings for ADC on AV96
ARM: dts: stm32: Add alternate pinmux for ADC pins
ARM: dts: stm32: Add bindings for FDCAN2 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN2 pins
ARM: dts: stm32: Add bindings for FDCAN1 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN1 pins
ARM: dts: stm32: Repair I2C2 operation on AV96
ARM: dts: stm32: Add alternate pinmux for I2C2 pins
...
Link: https://lore.kernel.org/r/19160355-364d-170c-7ae2-5ba7f714103f@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
-----BEGIN PGP SIGNATURE-----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=kTHc
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.8
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
* tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: s5pv210: Set MAX8998 GPIO pulls on Aries boards
ARM: dts: s5pv210: Correct FIMC definitions
ARM: dts: s5pv210: Assign clocks to MMC devices on Aries boards
ARM: dts: s5pv210: Enable ADC on Aries boards
ARM: dts: s5pv210: Add an ADC node
ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards
ARM: dts: s5pv210: Add si470x FM radio to Galaxy S
ARM: dts: s5pv210: Add remaining i2c-gpio adapters to Aries boards
ARM: dts: s5pv210: Add panel support to Aries boards
ARM: dts: s5pv210: Add touchkey support to Aries boards
ARM: dts: s5pv210: Add FSA9480 support to Aries boards
ARM: dts: s5pv210: Add WM8994 support to Aries boards
ARM: dts: s5pv210: Disable pulls on GPIO I2C adapters for Aries
ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries
ARM: dts: s5pv210: Correct gpi pinctrl node name
ARM: dts: s5pv210: Add sleep GPIO configuration for Galaxy S
ARM: dts: s5pv210: Add sleep GPIO configuration for Fascinate4G
ARM: dts: s5pv210: Add helper define for sleep gpio config
ARM: dts: exynos: Enable WLAN support for the UniversalC210 board
ARM: dts: exynos: Enable WLAN support for the Rinato board
...
Link: https://lore.kernel.org/r/20200512122922.5700-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
-----BEGIN PGP SIGNATURE-----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=cX7l
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use firmware PM driver for V3D
ARM: dts: bcm2711: Add vmmc regulator in emmc2
ARM: dts: bcm2711: Update expgpio's GPIO labels
Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
-----BEGIN PGP SIGNATURE-----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=WgDN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
DTS changes for omaps for v5.8 merge window
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP5: Make L4SEC clock domain SWSUP only
ARM: OMAP4: Make L4SEC clock domain SWSUP only
ARM: dts: omap5: add DES crypto accelerator node
ARM: dts: omap5: add SHA crypto accelerator node
ARM: dts: omap5: add aes2 entry
ARM: dts: omap5: add aes1 entry
ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
ARM: dts: DRA72x: Add aliases for rproc nodes
ARM: dts: DRA74x: Add aliases for rproc nodes
...
Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
-----BEGIN PGP SIGNATURE-----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=XZ07
-----END PGP SIGNATURE-----
Merge tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.8 kernel:
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Add devicetree for Integrator/AP with IM-PD1
Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Group the port definitions of the dvi-converter in a 'ports' node to
make it compliant with the ti,tfp410 binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "reset-controller" instead of "src" for
i.MX5 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupt is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "reset-controller" instead of "src" for
i.MX6/i.MX7 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing input mux for ENET2 mdio. Without this setting, it is not
possible to read the MDIO answers back from the PHY.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6SL, OCOTP can be
accessed directly, but since i.MX6SL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6QDL, OCOTP can be
accessed directly, but since i.MX6QDL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the wl_reg regulator to usdhc2 such that it can be enabled
and disabled as needed. There is no need for this to be always-on.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sterling-LWB has a BCM4330 which has a UART based bluetooth
HCI. Add support for binding to the bcm_hci driver to take care
of handling the shutdown gpio and loading firmware.
Because the shutdown gpio is more of an enable than a regulator
go ahead and replace the regulator with a shutdown-gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupt is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupt is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iomuxc-gpr node is not used and causes the following dtc
warning with W=1:
arch/arm/boot/dts/imx50.dtsi:286.28-289.6: Warning (unique_unit_address): /soc/bus@50000000/iomuxc@53fa8000: duplicate unit-address (also used in node /soc/bus@50000000/iomuxc-gpr@53fa8000)
Remove the node to fix the warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Let the PHY generate the RX and TX delay on the Odroid-C1 and MXIII
Plus.
Previously we did not know that these boards used an RX delay. We
assumed that setting the TX delay on the MAC side It turns out that
these boards also require an RX delay of 2ns (verified on Odroid-C1,
but the u-boot code uses the same setup on both boards). Ethernet only
worked because u-boot added this RX delay on the MAC side.
The 4ns TX delay was also wrong and the result of using an unsupported
RGMII TX clock divider setting. This has been fixed in the driver with
commit bd6f48546b ("net: stmmac: dwmac-meson8b: Fix the RGMII TX
delay on Meson8b/8m2 SoCs").
Switch to phy-mode "rgmii-id" to let the PHY side handle all the delays,
(as recommended by the Ethernet maintainers anyways) to correctly
describe the need for a 2ns RX as well as 2ns TX delay on these boards.
This fixes the Ethernet performance on Odroid-C1 where there was a huge
amount of packet loss when transmitting data due to the incorrect TX
delay.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200512215148.540322-3-martin.blumenstingl@googlemail.com
Add the "timing-adjusment" clock now that we now that this is connected
to the PRG_ETHERNET registers. It is used internally to generate the
RGMII RX delay no the MAC side (if needed).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200512215148.540322-2-martin.blumenstingl@googlemail.com
Use the Meson8m2 specific USB2 PHY compatible string. The 3.10 vendor
kernel has at least one known difference between Meson8 and Meson8m2:
Meson8m2 sets the ACA_ENABLE bit while Meson8 doesn't.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200515202520.1487514-1-martin.blumenstingl@googlemail.com
Testing with a USB RNDIS connection and iperf3 gives the following
results:
- From the host computer to the device at ~250Mbit/s
- From the device to the host computer at ~76Mbit/s
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200504195105.2909711-1-martin.blumenstingl@googlemail.com
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Let's also update the dts file to use #include while at it.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Note that for ti81xx, also timer1 is of type 2 unlike on am335x
where timer1 is type1 while the rest of the timers are type 2.
Cc: devicetree@vger.kernel.org
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Let's also update the dts file to use #include while at it.
Cc: devicetree@vger.kernel.org
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Note that similar to omap_init_time_of(), we now need to call
omap_clk_init() also from omap5_realtime_timer_init().
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now init system timers using the dmtimer and 32k counter
based on only devicetree data and drivers/clocksource timers.
Let's configure the clocksource and clockevent, and drop the old
unused platform data.
As we're just dropping platform data, and the early platform data
init is based on the custom ti,hwmods property, we want to drop
both the platform data and ti,hwmods property in a single patch.
Since the dmtimer can use both 32k clock and system clock as the
source, let's also configure the SoC specific default values. The
board specific dts files can reconfigure these with assigned-clocks
and assigned-clock-parents as needed.
Cc: devicetree@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move mmc nodes to be compatible with the sdhci-omap driver. The following
modifications are required for omap_hsmmc specific properties:
ti,non-removable: convert to the generic mmc non-removable
ti,needs-special-reset: co-opted into the sdhci-omap driver
ti,dual-volt: removed. Legacy property not used in am335x or am43xx
ti,needs-special-hs-handling: removed. Legacy property not used in am335x
or am43xx
Also since the sdhci-omap driver does not support runtime PM, explicitly
disable the mmc3 instance in the dtsi.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the disable-wp attribute from &emmc as it is, according to
Documentation/devicetree/bindings/mmc/mmc-controller.yaml:
"Not used in combination with eMMC or SDIO."
Suggested-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200406135006.23759-2-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Mecer Xtreme Mini S6 features a wireless module, based on a
Realtek 8723BS, which provides WLAN and Bluetooth connectivity via
SDIO and UART interfaces respectively.
Define a simple MMC power sequence that declares the GPIO pins
connected to the module's WLAN Disable and Bluetooth Disable pins
as active low reset signals, because both signals must be deasserted
for WLAN radio operation.
Configure the host's SDIO interface for High Speed mode with 1.8v
I/O signalling and IRQ detection over a 4-bit wide bus.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200406135006.23759-1-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm/boot/dts/rk3188-radxarock.dt.yaml: gpio-leds:
'blue', 'green', 'sleep'
do not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The common LED binding wants the LED node names to start with led- and
then have just a single number.
Changing the naming for the 8 user LEDs from using user<x> to led-<x>.
Also there is no default-trigger named "mmc0" in the kernel, so use the
more generic "disk-activity".
Link: https://lore.kernel.org/r/20200513103016.130417-18-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Most Arm Ltd. boards are employing a layered bus structure, to map
the hardware design (SoC, motherboard, IOFPGA) and structure the DTs.
The "simple-bus" nodes only allow a limited set of node names. Switch
to use *-bus to be binding compliant.
This relies on a pending dt-schema.git fix for now:
https://github.com/devicetree-org/dt-schema/pull/38
Link: https://lore.kernel.org/r/20200513103016.130417-16-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The UARTs for all Arm Ltd. boards were using "uart" as their node name
stub.
Replace that with the required "serial" string, to comply with the PL011
DT binding.
Link: https://lore.kernel.org/r/20200513103016.130417-14-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The sama5d2 SoC has two dedicated I2C IPs that are enabled on
sama5d2_xplained. Add alias for the i2c devices to not rely on
probe order for the i2c device numbering.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200518114802.253660-1-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, the leds and the config bus
subtree to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The NV+ v2 has a WH1602 LCD panel (which is just a rebranded HD44780),
similar to the Netgear RN104, just with different GPIO assignments.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5jTgAKCRCKwlD9ZEnx
cKSMAQCGIyrVtXHISZSFlp3poR1bBMejfxvZWmLIBzIPSw28SQEAqGTxP7dONrXY
JIbYmduRiRfWK6h0ghr769xp/KQPIAQ=
=dl06
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7 (take two)
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg20d-q7-dbcm-ca: Remove unneeded properties in hdmi@39
ARM: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
ARM: dts: r8a7740: Add missing extal2 to CPG node
Link: https://lore.kernel.org/r/20200515125043.22811-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Users can choose which flexcom function to use. Describe the I2C
Flexcom0 function. Add alias for the i2c2 node in order to not rely
on probe order for the i2c device numbering. The sama5d2 SoC has
two dedicated i2c buses and five flexcoms that can function as i2c.
The i2c0 and i2c1 aliases are kept for the dedicated i2c buses,
the i2c flexcom functions can be numbered in order starting from i2c2.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-16-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Indicate which i2c alias is for which connector on the board.
Specify that serial0 is for DBGU. This eases tester's life.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-17-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The aliases should be defined in the board dts rather than in the
SoC dtsi. Don't rely on the aliases defined in the SoC dtsi and define
the alias for the Serial DBGU in the board dts file. sama5d2 boards use
the "serial0" alias for the Serial DBGU, do the same for sama5d2_xplained.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-15-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Device aliases are board-specific, if needed one should define them
in board dts rather than in the SoC dtsi. If an alias from the SoC
dtsi is addressed by a driver that does not use any of the of_alias*()
methods, we can drop it. This is the case for the i2s aliases, drop
them. tcb aliases point to nodes that are not enabled in any of the
sama5d2 based platforms. atmel_tclib.c is scheduled to go away, any
board using that alias is already broken, so get rid of the tcb aliases
too.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-14-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Spare boards of duplicating the DMA bindings. Describe the flx0
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-12-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Spare boards of duplicating the DMA bindings. Describe the flx1
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-11-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Spare boards of duplicating the DMA bindings. Describe the flx3
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-10-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Spare boards of duplicating the DMA bindings. Describe the flx4
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-9-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The UART submodule in Flexcom has 32-byte Transmit and Receive FIFOs.
Tested uart7 on sama5d2-icp, which has both DMA and FIFO enabled.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-8-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
There is a single functional change in this patch. With the move of the
flx0 uart5 definition in the SoC dtsi, the uart5 from
at91-sama5d27_wlsom1_ek.dts inherits the following optional property:
atmel,fifo-size = <32>;
This particular change was tested by Codrin.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-7-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-6-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flexcom IP is part of the sama5d2 SoC. Move the flx2 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-5-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flexcom IP is part of the sama5d2 SoC. Move the flx3 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-4-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-3-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove the adi,input-style and adi,input-justification properties of
hdmi@39 to make it compliant with the "adi,adv7511w" DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-6-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Avenger96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an Avenger96 reference board. The DHCOR SoM can be populated with any
STM32MP15xx. Split the DTs to reflect this such that the common SoM and
Avenger96 parts are now in stm32mp15xx-dhcor-*dtsi and a specific example
implementation of STM32MP157A SoM and Avenger96 board is separated into
stm32mp157a-dhcor-*dts* . The stm32mp157a-avenger96.dts is retained for
the sake of backward naming compatibility.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx
variant. Split the SoC-independent parts of the SoM and PDK2 into the
stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example
of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add bindings for the four GPIO LEDs on DH PDK2 board. Note that LED5
GPIO-E may conflict with touchscreen interrupt, hence LED5 must be
disabled when using the DH 560-200 display unit with touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add bindings for the four GPIO keys on DH PDK2 board. Note that TA1
key is polled because it's IRQ line conflicts with ethernet IRQ, the
rest of the GPIO keys, TA2, TA3, TA4, are interrupt-driven and wake
up sources.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
IoT Box is an IoT gateway device based on Stinger96 board powered by
STM32MP1 SoC, designed and manufactured by Shiratech Solutions. This
device makes use of Stinger96 board by having it as a base board with
one additional mezzanine on top.
Following are the features exposed by this device in addition to the
Stinger96 board:
* WiFi/BT
* CCS811 VOC sensor
* 2x Digital microphones IM69D130
* 12x WS2812B LEDs
Following peripherals are tested and known to work:
* WiFi/BT
* CCS811
More information about this device can be found in Shiratech website:
https://www.shiratech-solutions.com/products/iot-box/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Stinger96 is a 96Boards IoT Extended edition board designed and
manufactured by Shiratech solutions based on STM32MP1 SoC. Following
are the features of this board:
* 256MB DDR
* 125MB NAND Flash
* Onboard BG96 modem
* 1x uSD
* 2x USB (1 available as external connector and another connected to BG96)
* 1x SPI
* 1x PCM
* 2x UART (apart from serial console)
* 2x I2C (apart from one connected to PMIC)
Following peripherals are tested and known to work:
* BG96 modem
* 1x I2C (LS-I2C0)
* 1x SPI
* 1x UART (LS-UART0)
* USB (Only Gadget mode)
* uSD
More information about this board can be found in Shiratech website:
https://www.shiratech-solutions.com/products/stinger96/
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These pinctrl definitions will be used by Stinger96/IoTBox boards
from Shiratech.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
-----BEGIN PGP SIGNATURE-----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=umsu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.6-rc cycle
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
* tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix occasional lost wakeirq for uart1
ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
ARM: dts: dra7: Fix bus_dma_limit for PCIe
ARM: dts: am574x-idk: Disable m_can node
Link: https://lore.kernel.org/r/pull-1588872844-804667@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
make dtc and the new dtscheck against yaml bindings happy.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl6yA9QQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeX0CACEwXPa8ChfXg+N4846D/wcwkpMVQqnTbMR
WrnqVLUNHf71h7Yej/aXpBSgEq5er1Q/HVgbjvkAAYNw633MNWgaNMi9AFl03gTF
uSOSUoiwauUUlvWt2aZ44IHxHS/WC0FB9/wIROpnD0SJvmYX9MJF8AVITNDsTDGv
EsSswwAXiBxILDWWdBM2QgAZxEhan3MwBbHQrmPRePDAWylluT3tMGjEfLgIapcW
9w44tw0kR8g7Zwgq+MYcfyHoNhUXOr1iMlCCA0LWOOtNBJAbXKM4XDp4cWwHLiI3
nktZSWXN7B08dx4hi/++18izC6N/ZwoGycMN4wG9kvdaRnpwh3KN
=vkl2
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes for the newly added Pinebook Pro and other fixes to
make dtc and the new dtscheck against yaml bindings happy.
* tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix pinctrl sub nodename for spi in rk322x.dtsi
arm64: dts: rockchip: Fix Pinebook Pro FUSB302 interrupt
ARM: dts: rockchip: swap clock-names of gpu nodes
arm64: dts: rockchip: swap interrupts interrupt-names rk3399 gpu node
arm64: dts: rockchip: fix status for &gmac2phy in rk3328-evb.dts
arm64: dts: rockchip: remove extra assigned-clocks property from &gmac2phy node in rk3328-evb.dts
ARM: dts: rockchip: fix phy nodename for rk3229-xms6
ARM: dts: rockchip: fix phy nodename for rk3228-evb
arm64: dts: rockchip: Rename dwc3 device nodes on rk3399 to make dtc happy
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3399 pmugrf node
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3328 grf node
arm64: dts: rockchip: drop non-existent gmac2phy pinmux options from rk3328
arm64: dts: rockchip: Replace RK805 PMIC node name with "pmic" on rk3328 boards
arm64: dts: rockchip: enable DC charger detection pullup on Pinebook Pro
arm64: dts: rockchip: fix inverted headphone detection on Pinebook Pro
arm64: dts: rockchip: Correct PMU compatibles for PX30 and RK3308
Link: https://lore.kernel.org/r/1738941.6LdaBJIBqS@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXqqEEQAKCRCKwlD9ZEnx
cK6VAQDEYT5s4bzgLANPkTuvz3n5NgmS1nSC9tGrUX9co4OEUgD+OkwEnFJgLF1+
LbwisW1fNfCz1looPeyyZTl9Q8o5Yg0=
=cIRT
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r7s9210: Remove bogus clock-names from OSTM nodes
arm64: dts: renesas: r8a77980: Fix IPMMU VIP[01] nodes
ARM: dts: r8a73a4: Add missing CMT1 interrupts
Link: https://lore.kernel.org/r/20200430084834.1384-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl6pHtIUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM69sAgAp/H4BASI7SAbrjYsFjCP+ymPVgeS
Y9oeLm09Q2XEF6GiRhK4SDqN56BOUelRI6nqWx3k6sU5A7SuZMqGSaZZEhCtHhjl
iixyxSccxh4prUWSEDQPHyIJ6yjBt+QkKhycOVLwq7FFLdlrSaRuameNQAkjEU4a
YPSL0oBd1xNbz75RaqgmyI0lzOuQg1P+GMQqmVOYfrucK94bq62FMSezyEBQxKU+
0MVG/hEkeLtxFgzE6OpkBs1p1m+KgXE7qvV0W84VyZOKgri1qJ74V1Pl/RJNNVA0
p46c3PH66OATAU7+pbshC0x/hsN8ZVAoBhPit5oLF7ugDNpi377jT/zRrw==
=z3sI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7:
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
* tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mp: update input_val for AUDIOMIX_BIT_STREAM
arm64: dts: imx8m: Fix AIPS reg properties
arm64: dts: imx8mn: Change SDMA1 ahb clock for imx8mn
ARM: dts: imx27-phytec-phycard-s-rdk: Fix the I2C1 pinctrl entries
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: imx6dl-yapp4: Fix Ursa board Ethernet connection
arm64: dts: ls1028a: add "fsl,vf610-edma" compatible
dt-bindings: dma: fsl-edma: fix ls1028a-edma compatible
Link: https://lore.kernel.org/r/20200429063226.GT32592@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GW552x-B board revision adds USB OTG support.
Enable the device-tree node and configure the OTG_ID pin.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Recent PTP-specific cpsw driver changes started exposing an issue on at
at least j5eco-evm:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf0169004
...
(davinci_mdio_runtime_suspend) from [<c063f2a4>] (__rpm_callback+0x84/0x154)
(__rpm_callback) from [<c063f394>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c063f4f0>] (rpm_suspend+0xfc/0x6ac)
(rpm_suspend) from [<c0640af0>] (pm_runtime_work+0x88/0xa4)
(pm_runtime_work) from [<c0155338>] (process_one_work+0x228/0x568)
...
Let's fix the issue by using the correct mdio clock as suggested by
Grygorii Strashko <grygorii.strashko@ti.com>.
The DM814_ETHERNET_CPGMAC0_CLKCTRL clock is the interconnect target module
clock and managed by ti-sysc.
Fixes: 6398f3478e ("ARM: dts: Configure interconnect target module for dm814x cpsw")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am437x-gp-evm
am437x-sk-evm
am437x-idk-evm
All above boards have phy-mode = "rgmii" and this is worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add SPI2 bindings to AV96 DT, the SPI2 IOs are present on
low-speed expansion connector X6. This is disabled by default
and can be enabled if something is connected there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for SPI2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for ADC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add FDCAN2 bindings to AV96 DT, the FDCAN2 is present on low-speed
expansion connector X6. This is disabled by default to match the
96boards specification though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add FDCAN1 bindings to AV96 DT, the FDCAN1 is present on low-speed
expansion connector X6. This is disabled by default to match the
96boards specification though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for FDCAN1 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The I2C2 uses different pinmux on AV96, use correct pinmux and
also add comments about the I2C being present on the "low-speed"
expansion connector X6.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for I2C2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Declare PSCI v1.0 support instead of v0.1 as the former is supported
by the PSCI firmware stacks stm32mp15x relies on.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Utilize common Tegra30 CPU OPP table. CPU DVFS is available now on beaver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set min/max voltage and couple CPU/CORE regulators.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OMAP5 contains a single DES crypto accelerator instance. Add node for
this in DT to enable it.
We keep the node disabled for now, as it appears OMAP5 platform is
running out of available DMA channels, and DES is the least interesting
crypto accelerator available on the device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the single available SHA crypto accelerator device for OMAP5 SoC.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES2 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has AES hardware cryptographic accelerator, add AES1 instance for
it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timer information has been added to all the IPU and DSP
remote processor device nodes in the DRA7xx/AM57xx SoC families. The
data has been added to the two common dra7-ipu-dsp-common and
dra74-ipu-dsp-common dtsi files that can be included by all the
desired board files. The following timers are chosen as the watchdog
timers, as per the usage on the current firmware images:
IPU2: GPTimers 4 & 9 (one for each Cortex-M4 core)
IPU1: GPTimers 7 & 8 (one for each Cortex-M4 core)
DSP1: GPTimer 10
DSP2: GPTimer 13
Each of the IPUs has two Cortex-M4 processors and so uses a timer
each for providing watchdog support on that processor irrespective of
whether the IPU is running in SMP-mode or non-SMP node. The chosen
timers also need to be unique from the ones used by other processors
(regular timers or watchdog timers) so that they can be supported
simultaneously.
The MPU-side drivers will use this data to initialize the watchdog
timer(s), and listen for any watchdog triggers. The BIOS-side code on
these processors needs to configure/refresh the corresponding timer
properly to not throw a watchdog error.
The watchdog timers are optional in general, but are mandatory to
be added to support watchdog error recovery on a particular processor.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and
the DSP remoteproc devices on the DRA76 EVM board, and assigned to
the respective rproc device nodes. These match the configuration
used on the DRA7 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA76 EVM board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA71 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and
the DSP1 remoteproc devices on the DRA72 EVM rev C board, and assigned
to the respective rproc device nodes. These match the configuration
used on the DRA72 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA72 EVM rev C board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA72 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on DRA7 EVM board. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for all the IPU and
DSP remoteproc devices in the DRA7 SoC family. The data is added
to the two common dra7-ipu-dsp-common and dra74-ipu-dsp-common
dtsi files that are included by all the desired board files. The
following timers are chosen, as per the timers used on the current
firmware images:
IPU2: GPTimer 3
IPU1: GPTimer 11
DSP1: GPTimer 5
DSP2: GPTimer 6
The timers are optional, but are mandatory to support advanced device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, if needed.
Each of the IPUs has two Cortex-M4 processors, and is currently
expected to be running in SMP-mode, so only a single timer suffices
to provide the BIOS tick timer. An additional timer should be added
for the second processor in IPU if it were to be run in non-SMP mode.
The timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required 'mboxes' property to all the IPU and DSP remote
processors (IPU1, IPU2, DSP1 and DSP2) in the two available common
dtsi files - dra7-ipu-dsp-common and dra74-ipu-dsp-common dtsi files.
The latter file is for platforms having DRA74x/DRA76x/AM572x/AM574x
SoCs which do have a DSP2 processor in addition to the other common
remote processors. The common data is added to the former file, and
the DSP2 only data is added to the latter file.
The mailboxes are required for running the Remote Processor Messaging
(RPMsg) stack between the host processor and each of the remote
processors. Each of the remote processors uses a single sub-mailbox
node, the IPUs are assumed to be running in SMP-mode. The chosen
sub-mailboxes match the values used in the current firmware images.
This can be changed, if needed, as per the system integration needs
after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for all the 3 remote processor nodes common to
all DRA72x/DRA71x/AM571x/AM570x boards. The aliases uses the
stem "rproc", and are defined in the order of the most common
processors on the DRA72x family. The ids are same as DRA74x
except for the missing DSP2.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for all the IPU and DSP remoteproc processor
nodes common to all DRA74x/DRA76x/AM572x/AM574x boards.
The aliases uses the stem "rproc". The aliases are defined
in the order of the most common processors on the DRA74x
family.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SoCs can contain upto two identical DSP
processor subsystems. The second DSP processor subsystem is
present only on the DRA74x/DRA76x variants. The processor
device DT node has therefore been added in disabled state for
this processor subsystem in the DRA74x specific DTS file.
NOTE:
1. The node does not have any mailboxes, timers or CMA region
assigned, they should be added in the respective board dts
files.
2. The node should also be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to support ti-sysc from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SOCs have two IPUs and upto two DSP
processor subsystems in general. The IPU processor subsystem
contains dual-core ARM Cortex-M4 processors, while the DSP
processor subsystem is based on the TI's standard TMS320C66x
DSP CorePac core. The IPUs are very similar to those on OMAP5.
Two IPUs and one DSP processor subsystems is the most common
configuration. The processor device DT nodes have been added
for these processor subsystems, with the internal memories
added through 'reg' and 'reg-names' properties. The IPUs only
have an L2 RAM, whereas the DSPs have L1P, L1D and L2 RAM
memories.
NOTE:
1. The nodes do not have any mailboxes, timers or CMA regions
assigned, they should be added in the respective board dts
files.
2. The nodes haven been disabled by default and the enabling
of these nodes is also left to the respective board dts
files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: convert to ti-sysc support from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With this, the clocksource driver can setup the timers properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clocksource to timer configured in pwm mode can be selected using the DT
property ti,clock-source. There are few pwm timers which are not
selecting the clock source and relying on default value in hardware or
selected by driver. Instead of relying on default value, always select
the clock source from DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like using the UART CTS pin does not always trigger for a wake-up
when the SoC is idle.
This is probably because the modem first uses gpio_149 to signal the SoC
that data will be sent, and the CTS will only get used later when the
data transfer is starting.
Let's fix the issue by configuring the gpio_149 pad as the wakeirq for
UART. We have gpio_149 managed by the USB PHY for powering up the right
USB mode, and after that, the gpio gets recycled as the modem wake-up
pin. If needeed, the USB PHY can also later on be configured to use
gpio_149 pad as the wakeirq as a shared irq.
Let's also configure the missing properties for uart-has-rtscts and
current-speed for the modem port while at it. We already configure the
hardware flow control pins with uart1_pins pinctrl setting.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.
The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.
In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sdmmc1 peripheral is connected on SD-card on STM32MP1-ED1 board.
Add the UHS features the controller is able to manage.
Those features require a level shifter on the board, and the support of
the voltage switch in driver, which is done in Linux v5.7.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 XDMA engine requires the PCI-E root control reset be cleared
as well, so add a phandle to that syscon reset.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Yosemite V2 is a facebook multi-node server
platform that host four OCP server. The BMC
in the Yosemite V2 platform based on AST2500 SoC.
This patch adds linux device tree entry related to
Yosemite V2 specific devices connected to BMC SoC.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Vijay Khemka <vkhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured
by YADRO.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the bus id for each mux channel to avoid switching channels
multiple times
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Connect the BMP280 and DPS310 to the hwmon subsystem with iio-hwmon
nodes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The BMC uses reserves the top 16MB of memory for the host to use for VGA
or PCIe communication.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geisonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
According to ASPEED, FTTMR010 is not intended to be used in the AST2600.
The arch timer should be used, but Linux doesn't enable high-res timers
without being assured that the arch timer is always on, so set that
property in the devicetree.
The FTTMR010 device is described by set to disabled.
This fixes highres timer support for AST2600.
Fixes: 2ca5646b5c ("ARM: dts: aspeed: Add AST2600 and EVB")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIO Q7 is no longer used for air/water. It is repurposed on Tacoma to
indicate internal FSI (low) vs cabled (high).
GPIO B0 controls the muxing of FSI to the cable (low) or internal pins
(high).
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Change the name of power, fault and rear-id.
Remove the two leds.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Regulators will be dynamically configured and monitored from userspace.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the Power CPUs that are attached to the
BMC.
Without this userspace will see the '/dev/scom66' style layout.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add gpio-keys for various signals on Tacoma.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
All 16 pins of the PCA9552 at 7-bit address 0x61 should be set as type
GPIO.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The second VUART is used to expose multiplexed, non-hypervisor consoles.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node to describe the video engine on AST2400.
These changes were copied from aspeed-g5.dtsi
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enabling emmc without enabling its controller doesn't do any good.
Enable its controller as well to make it work.
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added GPIO line names for all gpio used in tiogapass platform,
these line names will be used by libgpiod to control GPIOs
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding IPMB devices for facebook tiogapass platform.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 has Video Engine so add it.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add nodes for the interrupt controllers provided by the SCU.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the interrupt controller provided by the SCU.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the remaining two bridges on the Cyclone-V SoCFPGA SoCs.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The hps-to-fpga bridges can't be used, when the FPGA is not programmed.
Set the default state to disabled and leave enabling them to the board-specific
dts files.
Although this changes behavior, there are no in-tree users of the bridges, so
this won't break anything.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Make sure that the GPIOs are configured correctly
for the interrupt (otherwise it won't fire) and disable the
pulls on the DVS GPIOs which are outputs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The extended mainscaler is only available on FIMC1 and there
are minimum pixel alignments that differ from the default.
Additionally, the cam-if interface is available on all three
while FIMC2 has no rotators. The lcd-wb interface is supported
on FIMC1.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Aries boards, the ADC is used for things such as jack detection
and battery temperature monitoring. It is supplied by LDO4 of max8998,
so only enable that regulator when we are actually using the ADC.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos-adc driver now supports the S5PV210, so add the DT
node so that devices can use it.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The enable GPIO for the fixed vibrator regulator shouldn't be
pulled in one direction or the other.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add support for the Silicon Labs si4709 FM radio, which can be found
on Galaxy S GT-i9000 (but not on most of other Aries variants).
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The remaining i2c-gpio adapters that are common to all Aries boards
have devices without mainline bindings attachted to them. Add them
here for documentation.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have an s6e63m0 AMOLED panel connected over i2c-spi.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have soft touchkeys, manufactured by Cypress,
attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Fairchild FSA9480 is a USB mux connected over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a Wolfson WM8994 sound card attached over gpio-i2c.
There is currently no ASoC Machine Driver.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bitbanged GPIO I2C adapters have external pull-ups attached
so the internal pulls should be disabled for lower power usage.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
SDHCI1 is connected to a BCM4329 WiFi/BT chip which requires
power to be kept over suspend. As the surrounding hardware supports
this, mark it as such. This fixes WiFi after a suspend/resume cycle.
Fixes: 170642468a ("ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The node name was gpgi, but the pinctrl driver was registering the pins
as just gpi and the "samsung,pins" i2s0 pinctrl entries refer to gpi.
The public S5PC110 datasheet also refers to these pins as just gpi,
so let's make sure everything is in sync and rename the node to gpi.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to minimize leakage current during sleep, set a config
for sleep GPIOs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to minimize leakage current during sleep, set a config
for sleep GPIOs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
To simplify writing of sleep gpio configs, add a common helper
similar to what is present for other Samsung CPUs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Documentation/devicetree/bindings/spi/spi-uniphier.txt requires
#address-cells and #size-cells, but they are missing in actual DT files.
Also, 'make ARCH=arm dtbs_check' is really noisy.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add an 'aliases' property for ethernet device.
U-Boot performs a fix-up of the MAC address and will overwrite the values
from the Linux devicetree for aliased ethernet device. The MAC address can
be inherited from U-Boot by adding aliases of ethernet devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add external DMA controller support implemented in UniPhier SoCs.
This supports for Pro4, Pro5 and PXs2.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds the necessary MDIO interface node
to the Qualcomm IPQ4019 DTSI.
Built-in QCA8337N switch is managed using it,
and since we have a driver for it lets add it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED labels do not match the silkscreen on the board, fix it.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fill in the bindings for USB host and gadget on AV96.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fill in the bindings for HDMI audio on AV96, this permits audio playback
via attached HDMI device if such device supports it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add new mux option for SAI2 pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fill in the HDMI video pipeline from AV96 into the DT.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add new mux option for LTDC pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The WiFi/Bluetooth chip is attached to USART2 on AV96 as well, describe
it in DT to make it available. Remove BT LED and turn it into a shutdown
GPIO, because the GPIO line controls the BT_REG_ON signal. The LED is just
an indicator connected to the same line, but not the primary function.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The WiFi/Bluetooth SDIO chip is attached to SDMMC3 on AV96, describe it
in DT to make it available. Remove WiFi LED and turn it into a regulator,
because it is a GPIO controlling the WL_REG_ON input of the WiFi chip.
The LED is just an indicator connected to the same line, but not the
primary function.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add DT node describing the eMMC attached to SDMMC2 controller
of the STM32MP1 on DHCOR SoM, which is the SoM soldered on AV96.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for SDMMC1_D123DIR direction pins, SDMMC2 pins 4..7,
and SDMMC3 pins PD5_SDMMC3_D2 and PD0_SDMMC3_CMD, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The KS9031 PHY supports configurable PHY skews to compensate for
the board routing. Fill in the correct values.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The PMIC interrupt line is connected to PA0 on the DHCOR SoM, fix it.
This makes the POWER button on the AV96 working, and also all the other
PMIC interrupts. Furthermore, scrub the bogus interrupt-parent props.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The vdd PMIC buck regulator was misconfigured, which caused instability
of the board and malfunction of high-speed interfaces, like the RGMII.
Configure the PMIC correctly to repair these problems. Also add missing
Enpirion regulator for the IO voltage into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a device tree for the Integrator/AP with the
IM-PD1 logic module mounted, using the new logic
module bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the syscfg-fmp property in each i2c node in order to allow
Fast Mode Plus speed if clock-frequency >= 1MHz is indicated.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add declarations related to the syscon pdds for deep sleep management.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Usually it does not hurt to add "clock-names" properties, even if the
(pre-json-schema) DT bindings do not mention them.
However, the actual clock names for the OS Timer nodes are not fixed,
but contain the indices of the consumer instances. Hence they cannot
easily be used by a driver, without scanning for all possible indices.
Remove them, as the OSTM DT bindings do not specify clock-names anyway.
Fixes: bbbcd02b82 ("ARM: dts: r7s9210: Initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <Chris.Brandt@renesas.com>
Link: https://lore.kernel.org/r/20200427192932.28967-1-geert+renesas@glider.be
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
New compatible values were introduced for the 48-bit CMT devices on
SH-Mobile AG5 and R-Mobile A1, and the old "cmt-48"-based values were
deprecated. However, the actual DTS files were never updated.
See also commits:
- 81b604c399 ("dt-bindings: timer: renesas, cmt: Update CMT1 on
sh73a0 and r8a7740"),
- 8c1afba285 ("clocksource/drivers/sh_cmt: r8a7740 and sh73a0
SoC-specific match"),
- 19d608458f ("clocksource/drivers/sh_cmt: Document "cmt-48" as
deprecated").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200420151553.22975-1-geert+renesas@glider.be
LS1021A-TWR has one micron "n25q128a13" flash of size 16M.
Add QSPI node properties for it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the PMIC driver now has IRQ handling, add the GPIO to
listen to things like RTC alarm or ADC conversion completion.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I found
after restarting my randconfig build testing that had been dormant for
a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=K1jH
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I
found after restarting my randconfig build testing that had been
dormant for a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: imx8: select SOC_BUS
soc: tegra: fix tegra_pmc_get_suspend_mode definition
soc: fsl: dpio: avoid stack usage warning
soc: fsl: dpio: fix incorrect pointer conversions
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: bcm283x: Disable dsi0 node
firmware: xilinx: make firmware_debugfs_root static
drivers: soc: xilinx: fix firmware driver Kconfig dependency
ARM: dts: bcm283x: Add cells encoding format to firmware bus
ARM: dts: OMAP3: disable RNG on N950/N9
5.7, please pull the following:
- Nicolas provides a fix for 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
-----BEGIN PGP SIGNATURE-----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=6CKq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Nicolas provides a fix for 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
* tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Disable dsi0 node
ARM: dts: bcm283x: Add cells encoding format to firmware bus
Link: https://lore.kernel.org/r/20200417171725.1084-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b43 ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
AM5 IDK boards have TC358778 DPI-to-DSI bridge. Two different DSI panel
models are used with the AM5 IDKs, and these panels are added with DT
overlays. The AM5 IDKs can also be used without any panel.
Add TC358778 data to the am57xx-idk-common.dtsi, but set the status to
disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard.org BeagleBone AI is an open source hardware single
board computer based on the Texas Instruments AM5729 SoC featuring
dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital
signal processor (DSP), quad-core embedded vision engine (EVE),
Arm Cortex-M4 processors, dual programmable realtime unit
industrial control subsystems and more. The board features 1GB
DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash,
1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion
headers.
For more information, refer to:
https://beaglebone.ai
This patch introduces the BeagleBone AI device tree.
Note that the device use the "ti,tpd12s016" component which is
software compatible with "ti,tpd12s015". Thus we only use the
latter driver.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Even though commit cfb5d65f25 ("ARM: dts: dra7: Add bus_dma_limit
for L3 bus") added bus_dma_limit for L3 bus, the PCIe controller
gets incorrect value of bus_dma_limit.
Fix it by adding empty dma-ranges property to axi@0 and axi@1
(parent device tree node of PCIe controller).
Cc: stable@kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcbb63b802 ("ARM: dts: dra7: Separate AM57 dtsi files"),
the m_can node was inherited from dra76x.dtsi but the IP is not
connected on the idk board. Disable the node to reflect this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This introduces the MAX77826 PMIC that powers some pheripherals on the
klte, like the touchpad, touchkeys and camera.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200414172250.2363235-4-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung klte does not have a vreg_boost node. vreg_boost also
depends on pm8941-gpio which are not present on the klte.
Signed-off-by: Daniele Debernardi <drebrez@gmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200411182122.2677248-3-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The pma8084 replaces the pm8841,pm8941 found in other msm8974 devices.
It is used for various things including gpio keys, sdhci, usb, dsi.
The voltages are pulled from the vendor source tree.
Signed-off-by: Daniele Debernardi <drebrez@gmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20200411182122.2677248-2-iskren.chernev@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We need to tag RNG as disabled for N950/N9 as it blocked by the secure
mode. We have a similar change done for N900, but I missed adding it
for N950/N9 with the recent RNG changes.
-----BEGIN PGP SIGNATURE-----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=HJcs
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Boot regression fix for N950/N9
We need to tag RNG as disabled for N950/N9 as it blocked by the secure
mode. We have a similar change done for N900, but I missed adding it
for N950/N9 with the recent RNG changes.
* tag 'omap-for-v5.6/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: OMAP3: disable RNG on N950/N9
Link: https://lore.kernel.org/r/pull-1585340588-558327@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The I2C2 is routed out to header X21, enable it to make it available.
Add a comment to I2C5, which is routed to header X22 right next to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
a PMIC. The board has eMMC and a SD slot for storage and GbE
for both connectivity and power.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
While all sleep pinctrl group labels now follow a fixed naming scheme,
node _names_ for these groups don't:
- Some use ${dev}-[0-9], where the suffix is the normal group suffix + 1
- Some use ${dev}-sleep-[0-9], where suffix is the normal group suffix
- The <dc node uses ${dev}-[a-z]-[0-9], where the letter matches the
phandle and the number suffix is the normal group's suffix + 1
For uniformity, standardize on using ${dev}-[0-9]+ for all normal
pinctrl groups and ${dev}-sleep-[0-9]+ for all sleep pinctrl groups.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Some labels follow the *_sleep_pins_* naming scheme, but some also use
*_pins_sleep_*. Because most labels use the former and for uniformity
with variants like sdmmc1_b4_pins_a and sdmmc1_dir_pins_a, adopt the
*_sleep_pins_* scheme throughout.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
With the cell sizes specified in the SoC DTSIs in a previous commit,
individual boards no longer need to specify them, thus drop them.
No functional change.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The cell count for address and size is defined by the binding and not
something a board would change. Avoid each board adding this
boilerplate by having the cell size specification in the SoC DTSI.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In the original stm32mp157c.dtsi, the GPU was disabled as some SoC
variants lacked a GPU. We now have separate a dtsi for each SoC
variant and variants without a GPU lack the node altogether.
As we need no board support for using the GPU, enable it by default
and while at it remove the now redundant status = "okay" in existing
board device trees.
Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The R-Mobile APE6 Compare Match Timer 1 generates 8 interrupts, one for
each channel, but currently only 1 is described.
Fix this by adding the missing interrupts.
Fixes: f7b6523001 ("ARM: shmobile: r8a73a4: Add CMT1 node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200408090926.25201-1-geert+renesas@glider.be
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf820 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Y Soft yapp4 platform supports up to two Ethernet ports.
The Ursa board though has only one Ethernet port populated and that is
the port@2. Since the introduction of this platform into mainline a wrong
port was deleted and the Ethernet could never work. Fix this by deleting
the correct port node.
Fixes: 87489ec3a7 ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Introduce dtsi with overlay configuration for enabling UHS-I
for Colibri iMX6S/DL V1.1x re-design.
2. Introduce new dts for the Colibri iMX6S/DL V1.1x
on Colibri Evaluation Carrier Board V3.x. However, disable 1.8V for
the Colibri Evaluation Board since this carrier board has 3.3V pull-ups on.
3. Provide proper configuration for VGEN3, which allows that rail to
be automatically switched to 1.8 volts for proper UHS-I operation mode.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add
supply for cpu1.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7 uses cpufreq-dt driver which requires the CPU supply name to be
either "cpu0-supply" or "cpu-supply", correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
wlsom1 has an ATECC608A-TNGTLS Secure Element connected on the i2c0
bus. Add alias for the i2c device to not rely on probe order for the
i2c device numbering.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200413140922.154886-1-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
samsung-golden has the same sharp,gp2ap002s00f proximity sensor
that is also used in samsung-skomer.
A driver was added for it in
commit 97d642e230 ("iio: light: Add a driver for Sharp GP2AP002x00F").
Now that it was merged we can add an entry for it in the device tree
for samsung-golden.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200405173252.67614-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PWR-LED on the bananapi m2 zero board is on when gpio PL10 is low.
This has been verified on a board and in the schematics [1].
[1]: http://wiki.banana-pi.org/Banana_Pi_BPI-M2_ZERO#Documents
Fixes: 8b8061fcbf ("ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The H3 and H5 SoCs contain a message box that can be used to send
messages and interrupts back and forth between the ARM application CPUs
and the ARISC coprocessor. Add a device tree node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The A83T SoC contains a message box that can be used to send messages
and interrupts back and forth between the ARM application CPUs and the
ARISC coprocessor. Add a device tree node for it.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
OPP table value is get from orangepi lichee linux-3.4
kernel driver.
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is new version of A20-OLinuXino-LIME with eMMC storage. The
card routing is the same as in A20-OLinuXino-LIME2-eMMC, so this
is basically copy/paste.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Cherry-picked from CAF QSDK repo.
Original commit message:
The kernel is failing in switching the timer for high resolution
mode and clock source operates in 10ms resolution. The always-on
property needs to be given for timer device tree node to make
clock source working in 1ns resolution.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Link: https://lore.kernel.org/r/20200403114040.349787-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
vc4's firmware bus DMA limitations") as it turned out to be faulty
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEErOkkGDHCg2EbPcGjlfZmHno8x/4FAl5+ZSAACgkQlfZmHno8
x/7fWQf/SODT8sooJto4VFAbsDjXjNPmkqXBvFxYcPVN67ET2pSFdiGpGV4/Zt0+
/f1/niWVvOXL8j4MicEjhQeRwRCznzBHb07PW33ynf6i7u+b3eGr/gbfFckbpSsV
FhN5/5rcH7ebnsekGRG3c0386IGtRZW3xE4Dk2wLcRv3qhgs98y+U8s5vGlaxXG6
KAim6SUlh+FZak58CcVovBUe30HpX9vxuuHUk8mzhhrDEbZqDY2VW4VkhcagnAc8
y6X0mriyv6EoJdDzPQtlq94c/siNKIEbrJ/E5ozUU3ZNAs4nu2KIoru0lhXgaNl9
rMnHqEKCCF1/8gXeN1+t2DHXBfVvkA==
=/iN4
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=gRon
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-fixes-2020-03-27' into devicetree/fixes
This patch is to be squashed into 55c7c06210 ("ARM: dts: bcm283x: Fix
vc4's firmware bus DMA limitations") as it turned out to be faulty
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Second patch adds a fixed regulator that controls the SD power and
hooks it up with emmc2.
- Third patch rolls back to the firmware based power driver as the MMIO
version is unstable.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEErOkkGDHCg2EbPcGjlfZmHno8x/4FAl5+ZkYACgkQlfZmHno8
x/51Iwf/XKTwPJsNu3qaPeLZP6r3sMUSpIkb09+uF48ecYT2kKltMSWy4AMRILx1
GuPVyfhH9EOL7kf2pui+DotWfZ6V0w8QXmw+h5jmvrSL7HmNj7t+AUvlX765h/9/
tb+6/3Yum+GJwrG7mSmBCXvV4S5ReCdifmNse1WujgX5AfLZ/8SSdLl7/vwl5UTn
xkhGyGjGNwiabqwVZGAbhnv12IBsWPm7KAjpkPZRp6Yuyf9uawgnoNlIh4HDmH78
PBsXVoBlqlfBdroIVjjiUtcrqQIXxm4vcAwlCTXVKYC0boZib226a7D+bjrbVtRY
ou521MEikPI+tnydzQErBq7Ktj0SiA==
=q1oY
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Aotf
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2020-03-27' into devicetree/next
- First patch updates RPi4's expgpio's GPIO labels, adding the SD power rail.
- Second patch adds a fixed regulator that controls the SD power and
hooks it up with emmc2.
- Third patch rolls back to the firmware based power driver as the MMIO
version is unstable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DT bits to support the DH 560-200 display unit, which can be plugged
into the side of the PDK2 board. The display unit contains a display, EDT
ETM0700G0EDH6 and an EDT FT5x06 touchscreen controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is an EEPROM on at91-sama5d27_som1 connected to i2c0. i2c0 node
has to be moved from at91-sama5d27_som1_ek to at91-sama5d27_som1.
Enable the i2c EEPROM found on at91-sama5d27_som1. Add an alias for the
i2c node.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-5-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch enables the QSPI0 controller, configures its pin muxing and
declares a jedec,spi-nor memory.
sama5d2 Xplained RevB and RevC use the Macronix MX25L25673G flash
memory which advertises a maximum frequency of 80MHz for Quad IO
Fast Read. Set the spi-max-frequency to 80MHz knowing that actually
the QSPI drver will set the SPI bus clock to 166MHz / 3 = 55.3MHz.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-3-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
sdmmc1 is not populated by default on sam9x60ek, but there are cases
where it is populated with wilc3000. Add the node, but keep it disabled.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-4-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add SoM1 flash mapping, identical with the other SPI NOR flash
mappings found on the other at91 boards.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200403061222.1277147-2-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove non-removable and mmc-ddr-1_8v properties from the sdmmc0
node which come probably from an unchecked copy/paste.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes:42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221504.41196-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a node for BCM4330/2 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based UniversalC210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for BCM43342A SDIO chip on MSHC bus #1 and the required MMC
power sequence node for the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
mshc_0 node doesn't have any children, so there is no need for address
and size-cells properties.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the 'interrupts' and 'interrupts-parent' properties, which have
been superseded by the interrupts-extended property. While touching this,
fix the interrupts flags to correctly describe the hardware.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Both CPU-freq and dev-freq drivers support proper regulator lookup from
device-tree, so the early introduced hacks for registering main ARM VDD
regulator under 'vdd_arm' name are no longer needed. Similar for devfreq.
Fix this by removing the obsolete comments and changing the regulator
names to the one, which match the schematics and style for the given
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The updated "i2c-gpio" driver bindings require to define the SDA and SCL
GPIO lines in the separate properties and mark both as GPIO_OPEN_DRAIN.
Covert all Exynos dts files to follow this style.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.
The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.
Fixes: 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for BCM4330/3 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based Trats board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM43342A Bluetooth chip on the serial bus #0 on
the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add devicetree file for the Exynos4210 based Galaxy S2 (GT-I9100
version).
Signed-off-by: Stenkin Evgeniy <stenkinevgeniy@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD1195 DT.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Associate the UART nodes with the corresponding reset controller bits.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Group watchdog and UART0 into an Isolation syscon mfd node.
Group UART1 into a Miscellaneous syscon mfd node.
Cc: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Carve out 0xa800 for the boot ROM from the /memory@0 node,
updating it to /memory@a800, and add it to /soc ranges.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add Device Trees for Realtek RTD1195 SoC and MeLE X1000 TV box.
Reuse the existing RTD1295 watchdog compatible for now.
Reviewed-by: Rob Herring <robh@kernel.org>
[AF: Fixed r-bus size, fixed GIC, updated memreserve & memory]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This is required for wake on lan on i.MX6
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
-----BEGIN PGP SIGNATURE-----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=db/l
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids, and
other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHL9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymz6wCcDwDTZouXj+0B37q+kwlCQQPyLukAn2CxKfrM
d+wScRHWoZutA8IdzqaU
=5+jn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") the firmware bus has to comply with
/soc's DMA limitations. Ultimately linking both buses to a same
dma-ranges property. The patch (and author) missed the fact that a bus'
#address-cells and #size-cells properties are not inherited, but set to
a fixed value which, in this case, doesn't match /soc's. This, although
not breaking Linux's DMA mapping functionality, generates ugly dtc
warnings.
Fix the issue by adding the correct address and size cells properties
under the firmware bus.
Fixes: 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200326134413.12298-1-nsaenzjulienne@suse.de
The register based driver turned out to be unstable, specially on RPi3a+
but not limited to it. While a fix is being worked on, we roll back to
using firmware based scheme.
Fixes: e1dc2b2e1b ("ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20200303173217.3987-1-nsaenzjulienne@suse.de
The SD card power can be controlled trough a pin routed into the board's
external GPIO expander. Turn that into a regulator and provide it to
emmc2.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200306174413.20634-12-nsaenzjulienne@suse.de
I renamed the dsi-nodes from dsi@ to dsi-controller@
so that the schema check would kick in, but missed to
rename it in a few places.
Link: https://lore.kernel.org/r/20200326222536.86441-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Like on N900, we cannot access RNG directly on N950/N9. Mark it disabled in
the DTS to allow kernel to boot.
Fixes: 308607e554 ("ARM: dts: Configure omap3 rng")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With a non-critical clock fix for dm814x ethernet, we can update ti81xx
for cpsw ethernet and edma to probe them with ti-sysc interconnect
target module driver and device tree data. And we can drop the related
remaining platform data for cpsw and edma.
-----BEGIN PGP SIGNATURE-----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=EDSy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-drop-pdata-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop remaining legacy platform data for cpsw and edma
With a non-critical clock fix for dm814x ethernet, we can update ti81xx
for cpsw ethernet and edma to probe them with ti-sysc interconnect
target module driver and device tree data. And we can drop the related
remaining platform data for cpsw and edma.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for ti81xx edma
ARM: dts: Configure interconnect target module for ti816x edma
ARM: dts: Configure interconnect target module for dm814x tptc3
ARM: dts: Configure interconnect target module for dm814x tptc2
ARM: dts: Configure interconnect target module for dm814x tptc1
ARM: dts: Configure interconnect target module for dm814x tptc0
ARM: dts: Configure interconnect target module for dm814x tpcc
ARM: OMAP2+: Drop legacy platform data for dm814x cpsw
ARM: dts: Configure interconnect target module for dm814x cpsw
clk: ti: Fix dm814x clkctrl for ethernet
Link: https://lore.kernel.org/r/pull-1584575307-189595@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
-----BEGIN PGP SIGNATURE-----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=QqzI
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop legacy platform data for omaps for v5.7
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (56 commits)
ARM: OMAP2+: Drop legacy platform data for dra7 edma
ARM: OMAP2+: Drop legacy platform data for am3 and am4 edma
ARM: dts: Configure interconnect target module for dra7 tptc1
ARM: dts: Configure interconnect target module for dra7 tptc0
ARM: dts: Configure interconnect target module for dra7 tpcc
ARM: dts: Configure interconnect target module for am4 tptc2
ARM: dts: Configure interconnect target module for am4 tptc1
ARM: dts: Configure interconnect target module for am4 tptc0
ARM: dts: Configure interconnect target module for am4 tpcc
ARM: dts: Configure interconnect target module for am3 tptc2
ARM: dts: Configure interconnect target module for am3 tptc1
ARM: dts: Configure interconnect target module for am3 tptc0
ARM: dts: Configure interconnect target module for am3 tpcc
ARM: dts: dra7: Add PRU-ICSS interconnect target-module nodes
ARM: dts: AM4372: Add the PRU-ICSS interconnect target-module node
ARM: dts: AM33xx-l4: Update PRUSS interconnect target-module node
ARM: OMAP2+: Drop legacy platform data for am437x DSS
ARM: OMAP2+: Drop legacy platform data for dra7 DSS
ARM: OMAP2+: Drop legacy platform data for omap5 DSS
ARM: OMAP2+: Drop legacy platform data for omap4 dss
...
Link: https://lore.kernel.org/r/pull-1583858385-416921@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For proper bindings checks we need to properly group the port-phys and
sgpio-gpio items, so that they match the expected number of items.
Link: https://lore.kernel.org/r/20200228135106.220620-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently multiple interrupts for some devices are written as one array
instead of using the DT grouping notation (<0 42 4>, <0 23 4>).
This ends up in the same binary representation in the .dtb, but is
semantically not equivalent. The yaml schema checks will stumble over
this, so lets fix that first.
I refrained from using the symbolic names for GIC_SPI/GIC_PPI and
IRQ_TYPE_LEVEL_HIGH, mostly because it increases the delta between the
original DTS files and the mainline versions, so it's just additional
churn.
Link: https://lore.kernel.org/r/20200228135106.220620-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PL011 UART binding requires two clocks to be named in a node.
Add the second clock, which is the bus gate, that just gets enabled.
Since this is a fixed clock anyway, it doesn't make any difference.
Link: https://lore.kernel.org/r/20200228135106.220620-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The .dts files for the Calxeda machines are quite old, so carry some
sloppy mistakes that the DT schema checker will complain about.
Fix those issues, they should not have any effect on functionality.
Link: https://lore.kernel.org/r/20200228135106.220620-2-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.
-----BEGIN PGP SIGNATURE-----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=1cGm
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.7
This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.
* tag 'qcom-dts-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add gpio-ranges property
ARM: dts: qcom: msm8974-hammerhead: add support for bluetooth
ARM: dts: qcom: msm8974: add blsp2_uart10
ARM: dts: qcom: msm8974-honami: Add USB node.
Link: https://lore.kernel.org/r/20200318044305.GE470201@yoga
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename the IDE nodes to match the YAML schema
- Add a temperature zone to the DIR-685, use hard drive
as sensor and cool the case using the fan.
-----BEGIN PGP SIGNATURE-----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=/Tw7
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Gemini DTS changes for v5.7:
- Rename the IDE nodes to match the YAML schema
- Add a temperature zone to the DIR-685, use hard drive
as sensor and cool the case using the fan.
* tag 'gemini-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
Link: https://lore.kernel.org/r/CACRpkdbvgqCVuoMCHJrCZ0J+3NrwdrBnwBz+BJrSE=hqYh2j+Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New support for i.MX6/7 based PICO devices and Toradex i.MX7 based
Aster boards.
- Add voltage monitor device node for vf610-zii boards.
- Improve UART pins macro defines for i.MX6SX SoC and switch related
boards to use the new names.
- Use generic node name for devices like GPT, KPP, CCM, WDOG, OCOTP and
IOMUXC in i.MX DTS files.
- Switch imx6ul-pico device tree to DRM bindings.
- Use SPDX-License-Identifier for all Toradex i.MX6/7 based boards.
- Add proper rgmii PHY description for imx6dl-riotboard and
imx6q-marsboard.
- Add capture-subsystem device support for i.MX51.
- Kill off "simple-panel" compatibles which has never been an accepted
as an upstream compatible string.
- Random device addition to various boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5xkLsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5UZwgAh4EMxfFHTvfIO3Pobcax9qTnwQfX
A1cNE5VcZFhIt93FHV9H4k/rd/28v1QArs18X2PsdYk9NChzmEXSH1fPUQj7aMxT
NnDMDrkPaVGezWZbtoUEcpYr9sCxS6c0eMXq/VI2TTZS0pWPTzBBtsyqWiPbx3ZN
4h12SjS8T3M81VI90En1QStFAlg0YnDXYdEHNS3c/0rBcXLenkfPMlAeBJw6Rti2
9simCtJEDYnJpN77JUfFz8Lkm1bc7np4Fr56diKOrOmCeXD9VQ/qyy/KyBu99oRN
SL404Y7ACFc1OG9MMTkCKrbSCCQqa5ZseNyvV7PJEZImZ3XNb59+ICidRQ==
=42du
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm DTS changes for 5.7:
- New support for i.MX6/7 based PICO devices and Toradex i.MX7 based
Aster boards.
- Add voltage monitor device node for vf610-zii boards.
- Improve UART pins macro defines for i.MX6SX SoC and switch related
boards to use the new names.
- Use generic node name for devices like GPT, KPP, CCM, WDOG, OCOTP and
IOMUXC in i.MX DTS files.
- Switch imx6ul-pico device tree to DRM bindings.
- Use SPDX-License-Identifier for all Toradex i.MX6/7 based boards.
- Add proper rgmii PHY description for imx6dl-riotboard and
imx6q-marsboard.
- Add capture-subsystem device support for i.MX51.
- Kill off "simple-panel" compatibles which has never been an accepted
as an upstream compatible string.
- Random device addition to various boards.
* tag 'imx-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (55 commits)
ARM: dts: imx6q-marsboard: properly define rgmii PHY
ARM: dts: imx6dl-riotboard: properly define rgmii PHY
ARM: dts: imx51-zii-rdu1: set name prefix for TPA6130A2
ARM: dts: imx6: RDU2: assign video PLL as input to LDB
ARM: dts: vf: toradex: SPDX tags and copyright cleanup
ARM: dts: imx7: toradex: use SPDX-License-Identifier
ARM: dts: imx6: toradex: use SPDX-License-Identifier
ARM: dts: imx51: add capture-subsystem device
ARM: dts: imx: add nvmem property for cpu0
ARM: dts: imx6qdl: Add imx6qdl-pico support
ARM: dts: imx6ul-pico: Add support for the dwarf baseboard
ARM: dts: imx7d-pico: Add support for the nymph baseboard
ARM: dts: imx7d-pico: Add support for the dwarf baseboard
ARM: dts: imx23: introduce mmc0_sck_cfg
ARM: dts: imx25-pinfunc: add config for kpp rows 4 to 7
ARM: dts: imx: align name for crypto node and child nodes
ARM: dts: imx6qdl-gw5910: add CC1352 UART
ARM: dts: imx6qdl-sr-som-ti: indicate powering off wifi is safe
ARM: dts: imx6: phycore-som: add da9062 gpio support
ARM: dts: imx6: phycore-som: explicit disable pmic watchdog during suspend
...
Link: https://lore.kernel.org/r/20200318051918.32579-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename nodes to avoid dt-schema warnings
- Add a generic compatible to EEPROM so that it matches OF table
- Add USB controller nodes to Pro5 SoC
- Fix clock and reset of SPI nodes
-----BEGIN PGP SIGNATURE-----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=posG
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.7
- Rename nodes to avoid dt-schema warnings
- Add a generic compatible to EEPROM so that it matches OF table
- Add USB controller nodes to Pro5 SoC
- Fix clock and reset of SPI nodes
* tag 'uniphier-dt-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Set SCSSI clock and reset IDs for each channel
ARM: dts: uniphier: Add USB3 controller nodes for Pro5
ARM: dts: uniphier: Add one more generic compatible string for I2C EEPROM
ARM: dts: uniphier: rename cache controller nodes to follow json-schema
ARM: dts: uniphier: rename NAND node names to follow json-schema
ARM: dts: uniphier: rename aidet node names to follow json-schema
ARM: dts: uniphier: change SD/eMMC node names to follow json-schema
Link: https://lore.kernel.org/r/CAK7LNAQ-AOTyqpV1E_S-hksjqexHfVauwGV9rrfDvjRVnu8-UQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
-----BEGIN PGP SIGNATURE-----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=6UVu
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.7
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
* tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of the LCD SPI bus on UniversalC210 board
ARM: dts: exynos: Fix G3D power domain supply on Arndale Octa boards
ARM: dts: exynos: Fix G3D power domain supply on Odroid XU3/XU4/HC1 boards
ARM: dts: exynos: Fix memory on Artik5 evaluation boards
ARM: dts: exynos: Make fixed regulators always-on on Arndale5250
ARM: dts: exynos: Fix MMC regulator on Arndale5250 board
ARM: dts: exynos: Add dynamic-power-coefficient to Exynos5422 CPUs
ARM: dts: exynos: Add GPU thermal zone cooling maps for Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix broken reboot on some Odroid U2/X2/U3 boards
Link: https://lore.kernel.org/r/20200316175652.5604-3-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes and additions for 32-bit Tegra SoC device trees.
-----BEGIN PGP SIGNATURE-----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=qQJM
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.7-rc1
Minor fixes and additions for 32-bit Tegra SoC device trees.
* tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update sound node clocks in device tree
ARM: tegra: Add clock-cells property to PMC
ARM: tegra: Remove USB 2-0 port from Jetson TK1 padctl
Link: https://lore.kernel.org/r/20200313165848.2915133-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
- Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. It is based on stm32mp157c SoC.
- Add OTG full support on stm32mp15.
- Fix issues seen during yaml validation on stpmic and stmfx.
- Add i2c power/wakeup support on stm32mp15.
- Add card detect on sdcard on stm32mp boards
-----BEGIN PGP SIGNATURE-----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=89XF
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
- Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. It is based on stm32mp157c SoC.
- Add OTG full support on stm32mp15.
- Fix issues seen during yaml validation on stpmic and stmfx.
- Add i2c power/wakeup support on stm32mp15.
- Add card detect on sdcard on stm32mp boards
* tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits)
ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
ARM: dts: stm32: Correct stmfx node name on stm32746g-eval board
ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
ARM: dts: stm32: add USB OTG full support on stm32mp151
ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board
...
Link: https://lore.kernel.org/r/ded09d01-df47-9572-4679-34669bff8916@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- LCD/touchscreen support for the iwg22d-sodimm board.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXmtV7QAKCRCKwlD9ZEnx
cGL1AQC5+VUSTy4AMFEVxewSo9b9NY591/NT4qy3Dc/80Q40SgD/b1g78jUixCfc
ogKaoo6Jdkc9a281N/5r4hbjn6ovIAM=
=gLXn
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.7 (take two)
- LCD/touchscreen support for the iwg22d-sodimm board.
* tag 'renesas-arm-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg22d-sodimm: Enable touchscreen
ARM: dts: iwg22d-sodimm: Enable LCD panel
Link: https://lore.kernel.org/r/20200313154304.1636-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.7, please pull the following:
- Stefan adds GPIO labels to the Raspberry Pi 4 Model B board DTS
- Nicolas moves the eMMC2 controller into its separate node in order for
platform firmware to perform the necessary "dma-ranges" property
patching based on the chip revision since the eMMC controller has
different addressing constraints.
- Florian convers a whole bunch of Broadcom boards bindings from text to
YAML.
-----BEGIN PGP SIGNATURE-----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=H7v0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.7, please pull the following:
- Stefan adds GPIO labels to the Raspberry Pi 4 Model B board DTS
- Nicolas moves the eMMC2 controller into its separate node in order for
platform firmware to perform the necessary "dma-ranges" property
patching based on the chip revision since the eMMC controller has
different addressing constraints.
- Florian convers a whole bunch of Broadcom boards bindings from text to
YAML.
* tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux:
dt-bindings: arm: Document Broadcom SoCs 'secondary-boot-reg'
dt-bindings: arm: bcm: Convert Vulcan to YAML
dt-bindings: arm: bcm: Convert BCM11351 to YAML
dt-bindings: arm: bcm: Convert BCM4708 to YAML
dt-bindings: arm: bcm: Convert BCM23550 to YAML
dt-bindings: arm: bcm: Convert BCM21664 to YAML
dt-bindings: arm: bcm: Convert Stingray to YAML
dt-bindings: arm: bcm: Convert Northstar 2 to YAML
dt-bindings: arm: bcm: Convert Northstar Plus to YAML
dt-bindings: arm: bcm: Convert Hurricane 2 to YAML
dt-bindings: arm: bcm: Convert Cygnus to YAML
ARM: dts: bcm2711: Move emmc2 into its own bus
ARM: dts: bcm2711-rpi-4-b: Add SoC GPIO labels
Link: https://lore.kernel.org/r/20200311212012.9418-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few device tree changes for omaps for v5.7 to configure omap5
AESS module and to add idle_states for am335x and am437x cpuidle.
-----BEGIN PGP SIGNATURE-----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=DwZQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.7 merge window
Few device tree changes for omaps for v5.7 to configure omap5
AESS module and to add idle_states for am335x and am437x cpuidle.
* tag 'omap-for-v5.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Add idle_states for cpuidle
ARM: dts: am33xx: Add idle_states for cpuidle
ARM: dts: Configure omap5 AESS
Link: https://lore.kernel.org/r/pull-1583511417-919838@atomide.com-4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Schema validation for the top level of all ARM reference
designs: Integrator, Versatile, RealView, Juno.
- Clean up some node names in the trees so they pass
validation fine.
- Drop the old text bindings.
- A top level DMA ranges patch from Rob.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl5fvGIACgkQQRCzN7AZ
XXNf7xAAuf9DBhZ544JMn67I4reSltISWeng8TfPjT8ZB+3l8X+G6YEXoBdgd0dl
SYwtJyJ7wOQJk2jCy9L5lOnvF3frD8OIZw/UDAhHno/kn4yrR2/sHjhqSGEpspaL
wZ0LLRe6wnPNBQHgvGVa3T/Tr7nLbu5Gs/Z+LAb1C4V5atj386JLF9OxNcK5xUMx
+abJinQF1kI79N5HgLE+BZ5qNZG4COlcdHZz5im6sBPKF4UDyfHYqUY0FGUIhV4j
3biI1L5w0CWJ498eXOlQ5zMnuUyp17gEgd7MBOOe02LzJOfh6m2qHbOWIe8x22/i
sqs/Q5hwSeKzrKFzwQqgY/i9O/WeIvziMVUAb3FzcuTrXJGKHXpMXkSYhsAv+Yyv
gOkTmsUA4y9Q6LlhGCrZcpKzan7pM1rKtJMK+3yj/GvEookpzFj59LkWFHdsOIJZ
Gp34xT5hO8RKSrrNMX7b92svJtFdWciKWxVPlEK2pdfNam3+B0/nkv2QLDJ8e1t6
IslDcPDiJf7e0xEelG+tpkLpjls/1QSBA+kghZA5L0NL5mbnM9j4/NH7RMChfF/8
zu6VKuQdDNGjpEqocCDy0OlGjD0gNQcHHaCQepqMX6LaEnEoA3zQezjDDRpXg2l+
5ouUsPMtIWIG8lCxhI6XCFpWgmd05zOJRbbuKevoGwIchT1/bMA=
=0W6a
-----END PGP SIGNATURE-----
Merge tag 'versatile-dts-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.7 series take one:
- Schema validation for the top level of all ARM reference
designs: Integrator, Versatile, RealView, Juno.
- Clean up some node names in the trees so they pass
validation fine.
- Drop the old text bindings.
- A top level DMA ranges patch from Rob.
* tag 'versatile-dts-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM/arm64: dts: Rename SMB bus to just bus
dt-bindings: arm: Drop the non-YAML bindings
dt-bindings: arm: Add Versatile Express and Juno YAML schema
dt-bindings: arm: Add RealView YAML schema
dt-bindings: arm: Add Versatile YAML schema
dt-bindings: arm: Add Integrator YAML schema
ARM: dts: RealView: Fix the name of the SoC node
ARM: dts: Versatile: Use syscon as node name for IB2
ARM: dts: integratorap: Remove top level dma-ranges
Link: https://lore.kernel.org/r/CACRpkdbbniYVnsE-pAmU2qCerswserNgEFtY48XQ+_K+DUNC9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.6, please pull the following:
- Nick fixes the missing pinctrl-names property for the Raspberry Pi
Zero Wireless DTS
- Nicolas fixes the VC4 firmware node dma-range property which does not
have the limitations of the soc's bus node
* tag 'arm-soc/for-5.6/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
Link: https://lore.kernel.org/r/20200323025246.22713-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few more fixes for omaps
Just few dts fixes:
- A fix droid4 touchscreen stopping working with lost gpio interrupts
- Also limit omap5 dma range similar to what we've recently done for dra7
* tag 'omap-for-v5.6/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: dts: N900: fix onenand timings
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
Link: https://lore.kernel.org/r/pull-1584575254-461940@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit d4ec0cb050 ("ARM: dts: exynos: Add support for the
touch-sensitive buttons on Midas family") added a new fixed regulator
("voltage-regulator-6") to base "midas" .dtsi, but it didn't update the
clients of that .dtsi, which define their own fixed regulators starting
from the "voltage-regulator-6". This results in aliasing of the regulator
dt nodes and breaks operation of OLED panel due to lack of power supply.
Fix this by increasing the numbers in the fixed regulator names for those
boards.
Link: https://lore.kernel.org/r/20200316173710.3144-1-krzk@kernel.org
Fixes: d4ec0cb050 ("ARM: dts: exynos: Add support for the touch-sensitive buttons on Midas family")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.6, round 2:
- Fix minimum voltage setting of vdd_arm and vdd_soc on i.MX6
phycore-som board.
* tag 'imx-fixes-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
Link: https://lore.kernel.org/r/20200316032555.GD17221@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This follows up on the previous 5.6 fixes tag with a fix for the A33
Security System (crypto offloading hardware). The hardware was found
to not be compatible with existing hardware and a new compatible was
needed.
The driver change was picked up right before the previous -rc6 and
the DT bindings and DT changes were not picked up. The goal is to have
all the changes in the same release, that is v5.6.
-----BEGIN PGP SIGNATURE-----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=lpzG
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.6 - part 2
This follows up on the previous 5.6 fixes tag with a fix for the A33
Security System (crypto offloading hardware). The hardware was found
to not be compatible with existing hardware and a new compatible was
needed.
The driver change was picked up right before the previous -rc6 and
the DT bindings and DT changes were not picked up. The goal is to have
all the changes in the same release, that is v5.6.
* tag 'sunxi-fixes-for-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
Link: https://lore.kernel.org/r/20200313060727.GA23962@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
-----BEGIN PGP SIGNATURE-----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=yBY0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for v5.6
A pretty normal set of fixes for v5.6:
- Fix reversed macros used for A83T EMAC clock and reset
- Fix camera regulator voltage and USB OTG for TBS-A711
- 16-bit / 8-bit mixed read fix for our RSB driver
- Fix SPI controller base address for R40
- Reorder device nodes based on base address for R40
* tag 'sunxi-fixes-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
bus: sunxi-rsb: Return correct data when mixing 16-bit and 8-bit reads
ARM: dts: sun8i-a83t-tbs-a711: Fix USB OTG mode detection
ARM: dts: sun8i-a83t-tbs-a711: HM5065 doesn't like such a high voltage
ARM: dts: sun8i: a83t: Fix incorrect clk and reset macros for EMAC device
Link: https://lore.kernel.org/r/20200313055233.GA19649@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ralink,rt2880-uart is compatible with ns16550a and all other
instances of RT2880 UART nodes include it in the compatible property.
Add it also here, to make the binding schema simpler.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20200320174107.29406-8-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XScale serial port driver is perfectly capable of supporting this hardware. A
separate compatible string is probably a historical mess.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-7-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A preferred node name for serial ports is "serial":
mmp2-olpc-xo-1-75.dt.yaml: uart@d4030000: $nodename:0: 'uart@d4030000'
does not match '^serial(@[0-9a-f,]+)*$'
...
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-6-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the nodes by their phandle references instead of recreating the
tree and declaring references of the same names.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-5-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers that claim to support mrvl,mmp-uart default to a reg-shift
of two, some don't. Be explicit to be on a safe side.
With that in place, a XScale serial port driver is perfectly capable of
supporting the MMP serial port. Add a compatible string.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-4-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a preferred node name for serial ports, and it's not "uart":
pxa910-dkb.dt.yaml: uart@d4017000: $nodename:0: 'uart@d4017000'
does not match '^serial(@[0-9a-f,]+)*$'
...
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-3-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the nodes by their phandle references instead of recreating the
tree and declaring references of the same names.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200320174107.29406-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable all rps-irq interrupts during driver initialization to prevent
an accidental interrupt on GIC.
Fixes: 84316f4ef1 ("ARM: boot: dts: Add Oxford Semiconductor OX810SE dtsi")
Fixes: 38d4a53733 ("ARM: dts: Add support for OX820 and Pogoplug V3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The bus is virtual and devices have to inherit their DMA constraints
from the underlying interconnect. So add an empty dma-ranges property to
the bus node, implying the firmware bus' DMA constraints are identical to
its parent's.
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add USB device node for WLSoM1 EK and enable it.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
[eugen.hristev@microchip.com: ported to 5.4]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20200318104236.21114-1-eugen.hristev@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DIR-685 can now exploit the thermal zone added by the
drive temperature sensor inside the hard drive. We have
patched the libata subsystem to assign the device nodes
properly to the SCSI devices and this is what the drivetemp
driver will use to populate the sensor and the thermal
zone, so pick that up into the thermal zone and let this
control the fan.
The hardware lacks an embedded temperature sensor so the
D-Link vendor firmware uses this method to control the
temperature of the NAS enclosure using the thermal sensor
inside the hard drive.
The drive temperature trigger points to be used comes from
the vendor firmware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By renaming the ATA drive nodes to "ide@" we activate the
semantic checks to the DT schema for the controller and use
the correct notation for PATA drives.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ptp_ref clock for Arria10 defaults to using the peripheral
pll emac ptp clock. Without the ptp_ref clock in the gmac nodes
the driver defaults to the gmac main clock resulting in an
incorrect period for the ptp counter.
Signed-off-by: Dalon Westergreen <dalon.westergreen@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
'#address-cells' and '#size-cells' are needed in the same node (for the
child bus) as 'dma-ranges' in order to parse it. The kernel is more lax
and will walk up the tree to get the properties from a parent node, but
it's better to be explicit. dtc now does checks on 'dma-ranges' and is
more strict:
arch/arm/boot/dts/sun5i.dtsi:189.4-52: Warning (dma_ranges_format): \
/soc/dram-controller@1c01000:dma-ranges: "dma-ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/sun8i-r40.dtsi:742.4-52: Warning (dma_ranges_format): \
/soc/dram-controller@1c62000:dma-ranges: "dma-ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/sunxi-h3-h5.dtsi:563.4-52: Warning (dma_ranges_format): \
/soc/dram-controller@1c62000:dma-ranges: "dma-ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1)
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
OMAP5 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Cc: stable@kernel.org
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we can have the maxtouch touchscreen stop producing interrupts
if an edge interrupt is lost. This can happen easily when the SoC idles as
the gpio controller may not see any state for an edge interrupt if it
is briefly triggered when the system is idle.
Also it looks like maxtouch stops sending any further interrupts if the
interrupt is not handled. And we do have several cases of maxtouch already
configured with a level interrupt, so let's do that.
With level interrupt the gpio controller has the interrupt state visible
after idle. Note that eventually we will probably also be using the
Linux generic wakeirq configured for the controller, but that cannot be
done until the maxtouch driver supports runtime PM.
Cc: maemo-leste@lists.dyne.org
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure edma for
dm816x similar to what we have for dm814x.
Let's initially keep the legacy "ti,hwmods" peroperty, it will be
removed for all ti81xx in a later patch.
Note that as we now also start using the clkctrl clock binding on
dm816x, the board specific dts files must also have compatible
"ti,dm816". This is needed for the clkctrl clocks to probe properly,
so any out of tree dts files may need to be updated accordingly.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop the legacy "ti,hwmods" property.
As this module is very similar to what we already have configured
and working for am33xx, let's just update the whole cpsw with a
single patch to avoid some extra churn on the dts files.
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl5nwYURHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXNknBAAoxZgT7vx2BwsG0lpjbFrhBXIm9gQoCxC
fFiMRLX4PdEtMSzyHooszuBVJN/AzFb/dY43psccKZnwkigfAduiB/9Gn9Nw/Cwf
yLsaWiaUUfM6c1iQqv6HDV6fKal55emRZ/6RSfUlUMIyCcMRxg0NR8mSju3+uN9O
qGK2Ksxp4sRdG+m2KylNMB7MDSSHxKEsAmEMHlAQNOF6+O0m+AoDLN39XCY50XS+
2aUbcbyXbIK0lNSkbVOLf+UPZECIs7sy1qc02/OtG5i29z+0lJ/7men4R7gWIXRN
m7P0OPFlo8GyMKDcSfWDvw7UC2bNGvQKDisW4AfN3CjnlxD67S/F/bMbS8SK3Nec
vev/BmcMrhq4kEeTS+syUdLKwc8JI5dmrP/dhOBGwh1fdfoOrL2heG4ntLkMYX9r
SeEcSY3ixbr+/oClM61lbxV1TCro5oTzvWhYipf8KJiuXQD8ggEyeoO+0VAqK7Xq
LHdH+fEP2J72hXPdStUir6hJq1Fm1LClD9f0FPNWVj54xJtlHRYto/rKC7H3KzBJ
+KncyaFuUmOCDgt0bDqiTV7PXfURzqDERW6YL2UYpHGgQ0CqeBE89MGEKHU5Xzno
i8PrTFDLM9Icej8LIuD65CvFzAMFg5Hxu0bD7JDXh+Vmox5aHiQCPCLYD5oK3d/e
Z/tllQbJpIM=
=QqzI
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' into ti81xx
Drop legacy platform data for omaps for v5.7
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
We are missing alwon ethernet clock for dm814x and this prevents us
from probing the CPSW with device tree only data. Looks like Ethernet
currently only works if it has been enabled in the bootloader.
Looks like relying on the bootloader clocks is not an issue with the
mainline kernel currently, but it will be an issue when configuring
CPSW Ethernet to probe with device tree data only as we will be managing
the clocks.
Fixes: 26ca2e9738 ("clk: ti: dm814: add clkctrl clock data")
Cc: linux-clk@vger.kernel.org
Cc: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An experimental test with the command below gives
for example this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: i2s@10220000:
'#address-cells', '#size-cells'
do not match any of the regexes: 'pinctrl-[0-9]+'
'#address-cells' and '#size-cells' are not a valid property
for i2s nodes, so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'i2s' nodes are manually verified.
In order to automate this process rockchip-i2s.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-i2s.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@30160000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ohci', so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@30140000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ehci', so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ehci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'spdif' nodes are manually verified.
In order to automate this process rockchip-spdif.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-spdif.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312172240.21362-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
IO voltage regulator for the SD card must be kept on all the time,
otherwise when the board reboots the SD card can't be read by the
bootloader.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Link: https://lore.kernel.org/r/20200219204224.34154-1-JPEWhacker@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml: adc@1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rv1108-evb.dt.yaml: adc@1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-frequency' is not a valid property for a saradc node,
so remove it.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/iio/adc/
rockchip-saradc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200313132646.10317-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm/boot/dts/rk3288-firefly-reload.dt.yaml: saradc@ff100000:
'vref-supply' is a required property
PMIC Channel OUT11 with powername 'vcc_18'
(connected through R155 bridge with 'vccio_wl')
is used for the recovery key and ADC_AVDD_1V8.
Fix error by adding 'vcc_18' as vref for the saradc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/iio/adc/
rockchip-saradc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200314140755.4877-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables to use DMAC for all UARTs that are connected to
dmac_peri core for Rochchip RK3288.
Only uart2 is connected different DMAC (dmac_bus_s) so keep current
settings on this patch.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20200315095115.10106-1-katsuhiro@katsuster.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3066a-bqcurie2.dt.yaml:
l2-cache-controller@10138000: $nodename:0:
'l2-cache-controller@10138000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fix error by changing nodename to 'cache-controller'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/l2c2x0.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316165453.3022-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: lvds-encoder:
'ports' is a required property
Fix error by adding a ports wrapper for port@0 and port@1
inside the 'lvds-encoder' node for rk3188-bqedison2qc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
bridge/lvds-codec.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316174647.5598-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Pro5 and PXs2 are affected by this fix, but the SCSSI clock gate of Pro5 is
common to all channels.
Fixes: 92fa4f4cc2 ("ARM: dts: uniphier: add SPI node for UniPhier 32bit SoCs")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add USB3 controller nodes for Pro5 SoC and the boards.
Pro5 SoC has 2 controllers. USB0 includes 1 SS-PHY and 1 HS-PHY, and USB1
includes 1 SS-PHY and 2 HS-PHY.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Atheros AR8035 PHY can be autodetected but can't use interrupt
support provided on this board. Define MDIO bus and the PHY node to make
it work properly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Atheros AR8035 PHY can be autodetected but can't use interrupt
support provided on this board. Define MDIO bus and the PHY node to make
it work properly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set a sound name prefix for the HPA, as otherwise the sound controls
naming will clash with the controls of the DAC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently we don't ensure that the LDB is clocked from the video PLL
and relied on the bootloader to do the correct setup. This isn't always
true, in which case we would run with a vastly different video clock
than the desired one. Fix this by assigning the proper parent to the
LDB.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex Vybrid-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
4. Use GPL2.0+ instead of GPL2.0, as it's used now by default for all
new DTS files.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex i.MX7-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex iMX6-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
4. Use GPL2.0+ instead of GPL2.0, as it's used now by default for all
new DTS files from Toradex.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add IPU CSI ports and capture-subsystem device so the capture subsystem
part of the IPUv3EX can be used with the staging imx-media driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add nvmem related property for cpu0, then nvmem API could be used
to read cpu speed grading to avoid directly read OCOTP registers
mapped which could not handle defer probe.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the imx6ul pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the imx7d pico board with nymph baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the imx7d pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Olimex Olinuxino board has a user led connected to SSP1_DETECT.
But since this pin is listed in mmc0_pins_fixup, it is already claimed
by MMC driver and this results in this error during boot:
[ 1.390000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already
requested by 80010000.spi; cannot claim for leds
[ 1.400000] imx23-pinctrl 80018000.pinctrl: pin-65 (leds) status -22
[ 1.410000] imx23-pinctrl 80018000.pinctrl: could not request pin 65
(SSP1_DETECT) from group led_gpio2_1.0 on device 80018000.pinctrl
[ 1.420000] leds-gpio leds: Error applying setting, reverse things back
[ 1.430000] leds-gpio: probe of leds failed with error -22
This fix it, introduce mmc0_sck_cfg and switch the Olinuxino board to it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add USB components and according pin groups in aspeed-g6 dtsi.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On those boards, as stated in schematics files, the regulator used for IOs
is VDD. It was wrongly set to v3v3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On STM32MP1 DK1, DK2, ED1 and EV1 boards, there is only a micro SD socket.
This is also the case on Avenger board.
They don't support the Write Protect pin.
The disable-wp is then added in the SD-cards sdmmc1 nodes.
This avoids executing some code and a warning during driver probe.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The broken-cd properties are replaced with cd-gpios, with the correct
GPIO to detect the card insertion. The GPIO lines require a pull-up.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Remove unused properties from stpmic node.
The issues have been detected by running dtbs_check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the wakeup-source property in all i2c nodes of
the SoC stm32mp157c so that those I2C controllers can become
wakeup-source.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp157c-ed1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
DRA7 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Issues ere observed only with SATA on DRA7-EVM with 4GB RAM
and CONFIG_ARM_LPAE enabled. This is because the controller
supports 64-bit DMA and its driver sets the dma_mask to 64-bit
thus resulting in DMA accesses beyond L3 limit of 2G.
Setting the correct bus_dma_limit fixes the issue.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Samsung GT-S7710 also known as XCover 2 or Skomer is a
Ux500-based mobile phone. In the source code release from
Samsung's open source site it is referred to as "Skomer".
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200307193627.4092-1-linus.walleij@linaro.org
[Typographic fixups when applying]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the sleep state pinctrl entry for the i2c2 and i2c5 nodes
of the stm32mp157c-ev1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp15xx-dkx.dtsi
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On DK boards, all I2C4 bus slaves supports I2C Fast Mode hence setting
the bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On this board, the I2C4 bus has only a single slave (pmic) which
supports I2C Fast Mode hence setting bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
clk_out_1, clk_out_2, and clk_out_3 are part of Tegra PMC block but were
previously erroneously provided by the clock and reset controller.
clk_out_1 is dedicated for audio mclk on Tegra30 through Tegra210.
This patch updates device tree sound node to use clk_out_1 from the PMC
provider as mclk and uses assigned-clock properties to specify clock
parents for clk_out_1 and extern1.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has clk_out_1, clk_out_2, clk_out_3, and blink clock.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
This patch adds #clock-cells property with 1 clock specifier to the
Tegra PMC node in device tree.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Jetson TK1 USB 2-0 port is controlled by phy-tegra-usb driver
rather than padctl driver. Remove the entry for the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the new A33 SS compatible to the crypto node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the SPI device nodes were added, they were added in the wrong
location in the device tree file. The device nodes should be sorted
by register address.
Move the devices node to their correct positions within the file.
Fixes: 554581b791 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the SPI device nodes were added, SPI2 and SPI3 had incorrect
register base addresses.
Fix the base address for both of them.
Fixes: 554581b791 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Reported-by: JuanEsf <juanesf91@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318 ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Recent changes in the SPI core and the SPI-GPIO driver revealed that the
GPIO lines for the LD9040 LCD controller on the UniversalC210 board are
defined incorrectly. Fix the polarity for those lines to match the old
behavior and hardware requirements to fix LCD panel operation with
recent kernels.
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: amba: $nodename:0:
'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When we combine spi-rockchip.yaml and
spi-controller.yaml and add 'additionalProperties: false'
it gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: spi@10270000:
'#dma-cells' does not match any of the regexes:
'^.*@[0-9a-f]+$', '^slave$'
'#dma-cells' are not used for dma clients, so remove them all.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309134020.14935-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
for example this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: mmc@1021c000:
'default-sample-phase' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'default-sample-phase' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'rockchip,default-sample-phase'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: mmc@10218000:
'vmmcq-supply' does not match any of the regexes:
'^.*@[0-9]+$',
'^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$',
'pinctrl-[0-9]+'
'vmmcq-supply' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i.MX25's Keypad Port (KPP) can be used with a key pad matrix of up to
8 x 8 keys. Add pin configurations for rows 4 to 7.
The new defines have been tested on an out-of-tree board.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto node should use the "crypto" generic naming,
and not a specific one ("sahara", "dcp", "caam").
Child nodes of the crypto node for caam crypto engine
should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW5910-C revision adds a TI CC1352 connected to IMX UART4
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In one of the iWave-G22D development board variants, called Generic SODIMM
Development Platform, we have an LCD with touchscreen. The resistive touch
controller, STMPE811 is on the development board and is connected through
the i2c5 of the RZ-G1E.
Additionally, this controller should generate an interrupt to the CPU and
it is connected through GPIO4,4 to the GIC.
Touch was tested with one of our iW-RainboW-G22D-SODIMM RZ/G1E development
platforms.
More details on the iWave website:
https://www.iwavesystems.com/rz-g1e-sodimm-development-kit.html
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583336650-25848-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On the Generic SODIMM Development Platform there is an RGB LCD panel
directly connected to the DU output. It uses the TPU0 as backlight, one
GPIO pull-up configuration for power enable, R[2:7], G[2:7], B[2:7],
VSYNC, HSYNC, DU0_DISP and, DU0_CLK as inputs.
There is no encoder between the DU and the panel, therefore the default
connector driver is used.
The two variants of the iW-G22D should be mutually exclusive, therefore
this patch also disables the RGB LCD display when the HDMI extension board
is used.
Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1583239490-8837-1-git-send-email-marian-cristian.rotariu.rb@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pmic is a mfd device and supports gpios. Those gpios are not routed
to the SoM baseboard pin header but they are connected to the i.MX6. We
need the GPIO's to configure the pmic to select between the
suspend/resume arm and soc voltages
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default the phycore-som has support for two watchdog devices: 1st the
internal imx6 watchdog and 2nd the DA9062 PMIC watchdog. According [1]
the PMIC watchdog is used as boot watchdog. It is common to use this
watchdog during "system up" time too. Furthermore the PMIC watchdog can
be used to address ERR007117 since the phycore-som can be equipped with
NAND or eMMC storage.
The PMIC watchdog can be enabled/disabled by the PMIC itself if the PMIC
enters POWERDOWN mode or by the host. The PMIC powerdown mode can't be
used due to the PCB design. So the watchdog is still enabled during a
suspend which causes a system reset. We need to tell the driver to
disable the watchdog during a system suspend and to reenable it upon a
resume to fix this.
[1] https://git.pengutronix.de/cgit/barebox/tree/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi#n73
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX6/7 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX7, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCI support.
Since this board has an active high PCI reset line, pass the
'reset-gpio-active-high' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200117230845.25190-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Depending on bcm2711's revision its emmc2 controller might have
different DMA constraints. Raspberry Pi 4's firmware will take care of
updating those, but only if a certain alias is found in the device tree.
So, move emmc2 into its own bus, so as not to pollute other devices with
dma-ranges changes and create the emmc2bus alias.
Based in Phil ELwell's downstream implementation.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200304132437.20164-1-nsaenzjulienne@suse.de
Commit a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT nodes for HDMI video support for K2G EVM. The HDMI uses SiI9022
DPI as HDMI encoder. The DSS DPI is connected to SiI9022 HDMI
encoder's video input and encoder's output goes to HDMI connector.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add DT node for DSS. K2G has DSS version 6. Keystone family DSS are
somewhat different compered to the old OMAP family DSSes and the
binding looks different too.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also correct the custom node name to use generic node name dma.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A test with the command below gives these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml: /: 'model'
is a required property
arch/arm/boot/dts/rk3288-r89.dt.yaml: /: 'model'
is a required property
Fix this error by adding the missing model properties to
the involved dts files.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/root-node.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200304074051.8742-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The AM57xx family of SoCs contains two identical PRU-ICSS instances
that have a very unique SYSC register. The IPs do not have any
PRCM reset lines unlike those on AM33xx/AM437x SoCs. Add the PRUSS
interconnect target-module nodes with all the required properties.
Each of the PRUSS devices themselves shall be added as child nodes
to the corresponding interconnect node in the future. The PRU-ICSS
instances are only available on AM57xx family of SoCs and are not
supported on DRA7xx family of SoCs in general, so the target module
nodes are added in a separate dtsi file. This new dtsi file is
included in all the AM57xx SoC dtsi files, so the nodes are
automatically inherited and enabled on all AM57xx boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM437x family of SoCs contains two dissimilar PRU-ICSS instances,
but leverage a common reset line and SYSCFG from the larger PRU-ICSS1
instance. This SYSC register has also very unique bit-fields. Both
the IPs require the PRCM reset to be deasserted to be able to access
any registers. Add a common PRUSS interconnect target-module with all
the required properties.
The PRUSS devices themselves shall be added as child nodes to this
interconnect node in the future. The PRU-ICSS instances are not
supported on AM4372 SoC though in the AM437x family, so the target
module node should be disabled in any derivative board files that
use this SoC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on some AM33xx SoCs has a very unique SYSC
register. The IP also uses a hard-reset line, and requires this
PRCM reset to be deasserted to be able to access any registers.
Update the existing PRUSS interconnect target-module with all
the required properties.
The PRUSS device itself shall be added as a child node to this
interconnect node in the future. PRU-ICSS is not supported on
AM3351/AM3352/AM3354 SoCs though in the AM33xx family, so the
target module node should be disabled in derivative board files
that use any of these SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Note that we also fix a harmless typo for the node name, it's
dispc@400, not dispc@4000.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.
To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Note that we must disable smart idle modes for HDMI audio like we've
done with the legacy platform data. And HDMI needs both hdmi clock
and dss clock to operate.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
The display subsystem (DSS) is in a 16MB interconnect target module
mapped to l4 and l3 buses. We are only using the l3 port as recommended
by the TRM. So there is no need to configure l4 ranges like we've done
for l4 ABE instance for example.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Let's also add add a note about using only the l3 access without l4
as noted in the TRM.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IB2 syscon should not have any funny names, just call
it syscon@ as per the convention so the schema will apply
properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'dma-ranges' at the top level doesn't make sense. 'dma-ranges' implies
there is a parent bus node with '#address-cells' and '#size-cells' which
is impossible here.
Likely this translation needs to be moved down to sub-nodes that need
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for RGMII mode")
caused a regression for dm814x boards where NFSroot would no longer work.
Let's fix the issue by configuring "rgmii-id" mode as internal delays are
needed that is no longer the case with "rgmii" mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add vcc50_hdmi regulator for Vyasa RK3288 board.
VCC50_HDMI is the real name used for this regulator as
per the schematics.
This regulator used for HDMI connector by detecting the
cable via HDMI_EN gpio and input rails are sourced from
VSUS_5V regulator.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200123134641.30720-3-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
