Add a module parameter to adjust I2C SCL clock period per board. This allows
some experimental fine tuning by end users to overcome quirky I2C device
problems.
Reported-by: "Aleksandr V. Piskunov" <aleksandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the incoming MDL's buffers' bytesused and sync the buffers for the cpu
in one pass instead of two.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The encoder was not honoring the MDL size sent in DE_SET_MDL mailbox commands.
This change adjusts the size of the last buffer in an MDL, as reported to the
firmware, so that the encoder will send the exact amount of bytes we specify
per MDL transfer. This eliminates tearing in YUV playback when using
non-default YUV buffer sizes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix YUV capture such that the encoder will pass one frame per transfer. This
will allow the application to maintain frame alignment when a transfer from
the encoder is missed due to high system latency in service the CX23418 IRQ.
Also force YUV buffer sizes to be specified in multiples of 33.75 kB, the
smalled amount of buffer sizes need to store a complete set of HM12 4:2:0
macroblocks specifying 32 lines of the frame. A full 60Hz/525 line
screen requires 15 * 33.75 kB per frame and a full 50Hz/625 line screen
requires 18 * 33.75 kB per frame so the default buffer size is 3 * 33.75 kB,
requiring exactly 5 or 6 buffers per MDL respectively. The bytes needed per
frame and hence MDL need not be the bytes in an integer number of buffers.
However, if frame artifacts are seen with scaled screen sizes, the YUV buffer
size can be set 34 kB (33.75 kB) to get rid of the artifacts at the cost of more
copies between the kernel and userspace.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a Memory Descriptor List (MDL) layer to buffer handling to implement
scatter-gather I/O. Currently there is still only 1 buffer per MDL.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename type in anticipation of implementing a struct cx18_mdl type that
actually keeps track of a memory descriptor list.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the ov772x brightness was not setteble (fixed by M. Thrun)
- the set_frame_rate function does not work for ov965x
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The return value may be used uninitialized when the size parameter
happens to be 0.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use strlcat() to append a string to the previously created first part.
The semantic match that finds this kind of problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression dev;
expression phys;
expression str;
expression size;
@@
usb_make_path(dev, phys, size);
- strlcpy(phys, str, size);
+ strlcat(phys, str, size);
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All read transactions initiated by firedtv are only quadlet-sized, hence
the backend->read call can be simplified a little.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Packet DMA buffers are queued either initially all at once (then, a
queueing failure will cause firedtv to release the DMA context as a
whole) or subsequently one by one as they recycled after use (then a
failure is extremely unlikely). Therefore we can be a little less
cautious when counting at which packet buffer to set the interrupt flag.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache only addresses of whole pages, not of each buffer chunk. Besides,
page addresses can be obtained by page_address() instead of kmap() since
they were allocated in lowmem.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Prof 7301 PCI DVB-S2 card
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add #include <dvb_demux.h> for dvb_dmx_swfilter_packets(). This was
already indirectly included via firedtv.h, but don't rely on it.
The 4 bytes which were referred to as FIREWIRE_HEADER_SIZE are actually
the source packet header from IEC 61883-4 (MPEG2-TS data transmission
over 1394), not e.g. the IEEE 1394 isochronous packet header. So choose
a more precise name.
Also, express the payload size as a preprocessor constant too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
Canceling of the remote control workqueue job is factored into
firedtv-rc.c. Plus trivial whitespace change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This initialization of the value of audio_mode is the one used if nothing
matches in the subsequent switch. The variable audio_mode is subsequently
assigned to constants such as TUNER_AUDIO_MONO and TUNER_AUDIO_STEREO.
TUNER_AUDIO_STEREO has the same value as V4L2_TUNER_MODE_STEREO, so it
would seem better to use that value here.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the i2c base address is now taken from the sn9c1xx register table
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make id signed so we can't get an invalid pointer when we pass a negative
id.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In driver ./drivers/media/video/usbvideo/quickcam_messenger.c in line 91:
91 usb_make_path(dev, cam->input_physname, sizeof(cam->input_physname));
After this line we use strncat:
92 strncat(cam->input_physname, "/input0", sizeof(cam->input_physname));
where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol. But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.
In this case, after call to usb_make_path the similar drivers use strlcat.
Like in: drivers/hid/usbhid/hid-core.c:
1152 usb_make_path(dev, hid->phys, sizeof(hid->phys));
1153 strlcat(hid->phys, "/input", sizeof(hid->phys));
Found by Linux Driver Verification Project.
Use strlcat instead of strncat.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In driver ./drivers/media/video/usbvideo/konicawc.c in line 227:
227 usb_make_path(dev, cam->input_physname, sizeof(cam->input_physname));
After this line we use strncat:
228 strncat(cam->input_physname, "/input0", sizeof(cam->input_physname));
where sizeof(cam->input_physname) returns length of cam->input_phisname
without length for null-symbol. But this parameter must be - "maximum
numbers of bytes to copy", i.e.:
sizeof(cam->input_physname)-strlen(cam->input_physname)-1.
In this case, after call to usb_make_path the similar drivers use strlcat.
Like in drivers/hid/usbhid/hid-core.c:
1152 usb_make_path(dev, hid->phys, sizeof(hid->phys));
1153 strlcat(hid->phys, "/input", sizeof(hid->phys));
Found by Linux Driver Verification Project.
Use strlcat instead of strncat.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_queue_ops function vector is not declared constant, but
there's no need for the videobuf layer to ever change it. Make it const
so that videobuf users can make their operations const without warnings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
