Add support for mesh to ath10k. We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.
Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode. As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true. The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.
When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:
ip link set wlan0 down
iw dev wlan0 set type mp
ip link set wlan0 up
iw dev wlan0 set freq 5745 80 5775
iw dev wlan0 mesh join mesh-vht
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the case of raw mode without nohwcrypt parameter, we
should still make sure the frame is protected before
adding MIC_LEN to avoid skb_under_panic errors.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, ath10k restricts received frames to those matching BSSID.
When other BSS frames are requested (e.g. in mesh mode), add an internal
monitor device so those frames are not filtered.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes hardware reports invalid mcs index in rx descriptor
when operating in VHT80 mode and all packets with invalid mcs
will be eventually dropped in mac80211. This issue is observerd during
testing on QCA99X0 chipsets.
This patch adds a warn message for dumping the rx desc info which helps
in analysing the issue when invalid mcs is received.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to the VHT STS, this is supposed to be propagated by firmware.
In case it's not, use the default value, but as last resort.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The VHT STS CAP shall be reported by firmware to host, like in case of
QCA99x0. For QCA6174 hw family this isn't set for some reason.
So for this particular chips, let's assume it has the ability to
support VHT NDP in up to 4 STSs (which is true by the way).
Change the published beamformee STS cap accordingly to 3 or to what
the firmware reports.
Assumption so far, it suppose to be the num_rf_chains-1, was
completely wrong.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.
Fix this by limiting the probe responses when the specified
threshold limit is reached.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.
To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.
Failure happens with the following stack trace
[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MU-MIMO Rx involves different interpretation of
the VHT-SIG-A compared to SU-MIMO.
The incorrect interpretation led ath10k to report
VHT MCS values greater than 9 which subsequently
prompted mac80211 to drop such frames. This
effectively broke Rx with MU-MIMO in many cases
and manifested with a kernel warning in the log
which looked like this:
[ 14.552520] WARNING: CPU: 2 PID: 0 at net/mac80211/rx.c:3578 ieee80211_rx+0x26c/0x940 [mac80211]()
[ 14.552522] Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
... call trace follows ...
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
We don't support firmwares that don't use the new API.
This also allows to use all the SCD queues, so increase
the reported number of queues to 31.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
There's obviously no reason to write a NUL-terminating byte into
the debugfs file. Apparently nobody tried to use this from a tool
that doesn't strip NUL bytes though, so we never noticed. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
If we are in d0i3 when entering suspend, we leave d0i3 so that
mac80211 can call us to remove connections or whatever before going to
suspend. We do this by calling pm_runtime_resume() early in the slave
transport flow and reactivating it later, when the wiphy suspend flow
runs.
The problem is that we queue a work in order to leave d0i3. If this
work hasn't run yet when the wiphy suspend flow is called, we have a
race and entering d0i3 fails (because we're still holding the
IWL_MVM_REF_EXIT_WORK reference).
To solve this, simply flush the d0i3_exit_work at the beginning of the
iwl_mvm_suspend() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
When in AP mode, we need beacons from other APs for HT protection.
However, when there's no any associated station we will not do
any Tx and thus don't really need beacons. On the other hand, these
beacons will cause a lot of unnecessary wakeups which increase our
power consumption. Handle this by asking FW to pass beacons only when
there's at least one associated station.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
With CONFIG_IWLWIFI_DEVICE_TRACING=y, these functions are rather large,
too big for inlining.
With this .config: http://busybox.net/~vda/kernel_config,
after uninlining these functions have sizes and callsite counts
as follows:
iwl_read32 475 bytes, 51 callsites
iwl_write32 477 bytes, 90 callsites
iwl_write8 493 bytes, 3 callsites
Reduction in size is about 74,000 bytes:
text data bss dec hex filename
90758147 17226024 36659200 144643371 89f152b vmlinux0
90687995 17221928 36659200 144569123 89df323 vmlinux.after
Reported-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
ECHO_CMD is a simple command that can be sent to the
firmware just to check that it is alive.
This command is useful for debug purpose, provide a debugfs
hook to send it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
When receiving statistics notification there is a field of average energy.
This is defines as signed 8 bit, while FW refers to it as unsigned.
when the energy is higher than 127 this causes in iwl_mvm_stat_iterator
a wrong computation of the signal
int sig = -stats->general.beacon_filter_average_energy;
resulting in incorrect CQM event (change from low to high).
While at it - update the rest of the fields to the correct type.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
This debugfs entry was implemented just as a proof-of-concept before
the full support for netdetect via cfg80211/mac80211 was implemented.
Now that we have a proper way to enable netdetect from userspace, this
entry is redundant and should be removed to avoid unnecessary
maintenance work.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67 ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.
Fixes: e04cafbc38 ("ath10k: fix peer limit enforcement")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 5d5cd85ff4 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff4 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak")
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host platforms such as routers supported by OpenWRT can
support NVRAM reading directly from internal NVRAM store.
With this patch the nvram load routines will fall back to
this method when there is no nvram file and support is
available in the kernel.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The event mask length is determined by the highest event number
that is specified in the driver. When this length is shorter than
firmware expects setting event mask will fail and device becomes
pretty useless. This issue was reported with bcm4339 firmware that
was recently released.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_flowring_block blocks the last active flowring under the same
interface instead of the one provided by caller. This could lead to a
dead lock of netif stop if there are more than one flowring under the
interface and the traffic is high enough so brcmf_flowring_enqueue can
not unblock the ring right away.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcom is working on better reflection of interface combinations. With
upcoming patches we may have 1st combination supporting less interfaces
than others.
To don't run out of addresses check all combinations to find the one
with the greatest max_interfaces value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
current code will handle -ETIMEDOUT as success which is probalbly wrong.
According to this comment I assume it is safe to handle -ETIMEDOUT as false:
drivers/net/wireless/ath/ath9k/calib.c
290 /*
291 * We timed out waiting for the noisefloor to load, probably due to an
292 * in-progress rx. Simply return here and allow the load plenty of time
293 * to complete before the next calibration interval. We need to avoid
294 * trying to load -50 (which happens below) while the previous load is
295 * still in progress as this can cause rx deafness. Instead by returning
296 * here, the baseband nf cal will just be capped by our present
297 * noisefloor until the next calibration timer.
298 */
Since no other error wariants are present, this patch is checking only
for (ret <= 0).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
Add support for the new (bigger) TX power command. This doesn't
actually take advantage of the new capabilities (to set per-chain
TX power limits) but makes the code compatible with newer firmware
images expecting the larger command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
split long debug messages that may result warning in tracing.
Fixes: 1a84e77160 ("iwlwifi: mvm: add debug info to schedule scan complete message.")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The command string array is assumed to be indexable by a full u8, so it
must have 256 entries (0-255), not just 255. A recent firmware change
(apparently) started using the command 0xff for a notification to the
host, causing the driver to crash in debug message/tracing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when waking from d0i3 there is a wakeup reason.
Enum in driver is not up to date with FW api - fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
My static checker complains that we don't check for underflows in
iwl_dbgfs_fw_dbg_conf_write(). This is harmless because we have a
sanity check in iwl_mvm_start_fw_dbg_conf(), but we may as well make
this unsigned and silence the underflow warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Kalle Valo says:
====================
Major changes:
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in code that's one
byte larger (for me), but reduces struct link_ant and struct link
size by the two unsigned long values that store the parameters each.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces code size slightly (at least on x86/64) while also
removing memory consumption by two unsigned long values for each
ath5k device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If .pull_fw_stats() fails for some reason while processing
fw stats event, collected pdev/vdev/peer stats just before
the failure should be freed. This is unlikely to happen,
just code review catch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found incorrect sequence in ath10k_core_stop() where wmi pktlog
disable cmd is passed from ath10k_debug_stop() to firmware
immediately after wmi pdev suspend cmd. Firmware will not accept
any wmi cmd after receiving wmi pdev suspend cmd.
Fix this issue in ath10k_core_stop() by moving ath10k_debug_stop()
just before sending pdev suspend cmd. So that pktlog disable cmd
will get passed before pdev suspend cmd.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
