commit 07c6b2d01d upstream.
Since the switch from mmp_pdma to pxa_dma driver for pxa architectures,
the pxa_dma requires 2 arguments, namely the requestor line and the
requested priority.
Fix the only left device node which was still passing only one argument,
making the pxa3xx-nand driver misbehave in a device-tree configuration,
ie. failing all data transfers.
Fixes: c943646d1f ("ARM: dts: pxa: add dma engine node to pxa3xx-nand")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a7f31eb7 upstream.
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfe1580a64 upstream.
commit 55ee7017ee ("arm: omap2: board-generic: use omap4_local_timer_init
for AM437x") makes synctimer32k as the clocksource on AM43xx. By default
the synctimer32k is clocked by 32K RTC OSC on AM43xx. But this 32K RTC OSC
is not available on epos boards which makes it fail to boot.
Synctimer32k can also be clocked by a peripheral PLL, so making this as
clock parent for synctimer3k on epos boards.
Fixes: 55ee7017ee ("arm: omap2: board-generic: use omap4_local_timer_init for AM437x")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b02acd4e62 upstream.
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae3fc8ea08 upstream.
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416d ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f514e6907 upstream.
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7d5a43c0d upstream.
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aae6b18f5c upstream.
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e873cc022c upstream.
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f505dba762 upstream.
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec504 ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af756bbccf upstream.
The palmas PMIC has two control lines that need to be muxed properly
for things to work. The sys_nirq pin is used for interrupts, and msecure
pin is used for enabling writes to some PMIC registers.
Without these pins configured properly things can fail in mysterious
ways. For example, we can't update the RTC registers on palmas PMIC
unless the msecure pin is configured. And this is probably the reason
why we had RTC missing from the omap5 dts file.
According to "OMAP5430 ES2.0 Data Manual [Public] VErsion A (Rev. F)"
swps052f.pdf, mux mode 1 is for sys_drm_msecure so in theory there's
should be no need to configure it as a GPIO pin.
However, it seems there are some reliability issues using the msecure
mux mode. And the TI trees configure the msecure pin as GPIO out high
instead.
As the PMIC only cares that the msecure line is high to allow access
to the RTC registers, let's use a GPIO hog as suggested by Nishanth
Menon <nm@ti.com>. Also the use of the internal pull was considered
but supposedly that may not be capable of keeping the line high in
a noisy environment.
If we ever see high security omap5 products in the mainline tree,
those need to skip the msecure pin muxing and ignore setting the GPIO
hog. Chances are the related pin mux registers are locked in that case
and the msecure pin is managed by whatever software may be running in
the ARM TrustZone.
Who knows what the original intention of the msecure pin was. Maybe
it was supposed to prevent the system time to be set back for some
game demo modes to time out? Anyways, it seems that later PMICs like
tps659037 have recycled this pin for "powerhold" and devices like
beagle-x15 do not need changes to the msecure pin configuration.
To avoid further confusion with TWL variant PMICs, beagle-x15 does
not have a back-up battery for RTC palmas. Instead the mcp79410 RTC
is used with rtc-ds1307 driver. There is a "powerhold" jumper j5
holes near the palmas PMIC, and shorting it seems to power up
beagle-x15 automatically. It is unknown if it also has other side
effects to the beagle-x15 power up sequence.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ea24daae0 upstream.
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 418d551656 upstream.
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 079ae0c121 upstream.
The Armada 388 GP Device Tree file describes two times a regulator
named 'reg_usb2_1_vbus', with the exact same description. This has
been wrong since Armada 388 GP support was introduced.
Fixes: 928413bd85 ("ARM: mvebu: Add Armada 388 General Purpose Development Board support")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM SoC fixes from Arnd Bergmann:
"This is the final small set of ARM SoC bug fixes for linux-4.4, almost
all regressions:
OMAP:
- data corruption on the Nokia N900 flash
Allwinner:
- Two defconfig change to get USB working again
ARM Versatile:
- Interrupt numbers gone bad after an older bug fix
Nomadik:
- Crashes from incorrect L2 cache settings
VIA vt8500:
- SD/MMC support on WM8650 never worked"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dts: vt8500: Add SDHC node to DTS file for WM8650
ARM: Fix broken USB support in multi_v7_defconfig for sunxi devices
ARM: versatile: fix MMC/SD interrupt assignment
ARM: nomadik: set latencies to 8 cycles
ARM: OMAP2+: Fix onenand rate detection to avoid filesystem corruption
ARM: Fix broken USB support in sunxi_defconfig
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
Signed-off-by: Roman Volkov <rvolkov@v1ros.org>
Reviewed-by: Alexey Charkov <alchark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 0976c946a6
"arm/versatile: Fix versatile irq specifications"
has an off-by-one error on the Versatile AB that has
been regressing the Versatile AB hardware for some time.
However it seems like the interrupt assignments have
never been correct and I have now adjusted them according
to the specification. The masks for the valid interrupts
made it impossible to assign the right SIC interrupt
for the MMCI, so I went in and fixed these to correspond
to the specifications, and added references if anyone
wants to double-check.
Due to the Versatile PB including the Versatile AB
as a base DTS file, we need to override and correct
some values to correspond to the actual changes in the
hardware.
For the Versatile PB I don't think the IRQ line
assignment for MMCI has ever been correct for either of
the two MMCI blocks. It would be nice if someone with the
physical PB board could test this.
Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.
Cc: Rob Herring <robh@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: stable@vger.kernel.org
Fixes: 0976c946a6 ("arm/versatile: Fix versatile irq specifications")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Nomadik has sporadic crashes because of these latencies, setting
them to max makes the platform work nicely, so use this values for
now.
These latencies were set to 2 since the Nomadik platform was merged,
but I suspect they never took effect until the right size and
associativity for the cache was specified in the device tree and
that is why the crash comes now.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"A smallish set of fixes that we've been sitting on for a while now,
flushing the queue here so they go in. Summary:
A handful of fixes for OMAP, i.MX, Allwinner and Tegra:
- A clock rate and a PHY setup fix for i.MX6Q/DL
- A couple of fixes for the reduced serial bus (sunxi-rsb) on
Allwinner
- UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
- Suspend fix for Tegra124 Chromebooks
- Fix for missing implicit include that's different between
ARM/ARM64"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
bus: sunxi-rsb: Fix peripheral IC mapping runtime address
bus: sunxi-rsb: Fix primary PMIC mapping hardware address
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
fsl-ifc: add missing include on ARM64
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960 ("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Few fixes for omaps to allow am437x only builds to boot properly with
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
* tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'assigned-clock-parents' and 'assigned-clock-rates' list
should corresponding to the 'assigned-clocks' property clock list.
Signed-off-by: Bai Ping <b51503@freescale.com>
Fixes: ed339363de ("ARM: dts: imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
Merge "Marvell Berlin fixes for 4.4-rc1 (round 1)" from Sebastian Hesselbarth:
- fix wrong SDIO DT clocks on BG2Q
* tag 'berlin-fixes-for-4.4-rc1-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
The Ethernet controller found in the Armada 38x SoC's family support
TCP/IP checksumming with frame sizes larger than 1600 bytes, however
only on port 0.
This commit enables it by setting 'tx-csum-limit' to 9800B in
'ethernet@70000' node.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only the bus clock has been assigned, but in reality the
SAI IP has for clock inputs. The driver has been updated to
make use of the additional clock inputs by c3ecef21c3 ("ASoC:
fsl_sai: add sai master mode support"). Due to a bug in the
clock tree, the audio clock has been enabled none the less by
the specified bus clock (see "ARM: imx: clk-vf610: fix SAI
clock tree"), which made master mode even without the proper
clock assigned working.
This patch completes the clock definition for SAI2. On Vybrid,
only two MCLK out of the four options are available (the first
being the bus clock itself). See chapter 8.10.1.2.3 of the
Vybrid Reference manual ("SAI transmitter and receiver options
for MCLK selection"). Note: The audio clocks are only required
in master mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing SPI controller DMA handler in the dm816x DT
node, only properties for the two channels on four were present.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
Merge "ARM: rockchip: devicetree fixes for 4.4" from Heiko Stuebner:
Two fixes to Rockchip devicetree files, disabling the mmc-tuning
on the veyron-minnie board for now and adding the init state for
the over-temperature-protection to prevent glitches making the
system reboot sometimes.
* tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
Merge "Fixes for omaps for v4.4-rc cycle" from Tony Lindgren:
- A series of audio changes for dra7 that missed the merge window but turned
out to be necessary to fix a boot time imprecise external abort error and to
getaudio working
- Fix l4 related boot time errors for dm81xx
- Use lockless cldm/pwrdm api in omap4_boot_secondary
- Remove t410 custom abort handler that is no longer needed and may
hide other critical errors
- Mark cpuidle tracepoints as _rcuidle
- Fix module alias for omap-ocp2scp
* tag 'omap-for-v4.4/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: OMAP2+: remove custom abort handler for t410
ARM: OMAP: DRA7: hwmod: Add data for McASP3
ARM: OMAP2+: hwmod: Add hwmod flag for HWMOD_OPT_CLKS_NEEDED
ARM: dts: dra7: Fix McASP3 node regarding to clocks
bus: omap-ocp2scp: Fix module alias
ARM: OMAP2+: PM: Denote the cpuidle tracepoints as _rcuidle()
Merge "Few Keystone fixes for 4.4-rcx" from Santosh Shilimkar:
- Fix the optional PDSP firmware loading
- Fix linking RAM setup for QMs
- Fix crash with clk_ignore_unused
* tag 'keystone-fixes-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
