Commit Graph

3 Commits

Author SHA1 Message Date
Daniel Borkmann
e3f5b17047 net: ipv6: mld: get rid of MLDV2_MRC and simplify calculation
Get rid of MLDV2_MRC and use our new macros for mantisse and
exponent to calculate Maximum Response Delay out of the Maximum
Response Code.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-04 14:53:20 -04:00
Daniel Borkmann
89225d1ce6 net: ipv6: mld: fix v1/v2 switchback timeout to rfc3810, 9.12.
i) RFC3810, 9.2. Query Interval [QI] says:

   The Query Interval variable denotes the interval between General
   Queries sent by the Querier. Default value: 125 seconds. [...]

ii) RFC3810, 9.3. Query Response Interval [QRI] says:

  The Maximum Response Delay used to calculate the Maximum Response
  Code inserted into the periodic General Queries. Default value:
  10000 (10 seconds) [...] The number of seconds represented by the
  [Query Response Interval] must be less than the [Query Interval].

iii) RFC3810, 9.12. Older Version Querier Present Timeout [OVQPT] says:

  The Older Version Querier Present Timeout is the time-out for
  transitioning a host back to MLDv2 Host Compatibility Mode. When an
  MLDv1 query is received, MLDv2 hosts set their Older Version Querier
  Present Timer to [Older Version Querier Present Timeout].

  This value MUST be ([Robustness Variable] times (the [Query Interval]
  in the last Query received)) plus ([Query Response Interval]).

Hence, on *default* the timeout results in:

  [RV] = 2, [QI] = 125sec, [QRI] = 10sec
  [OVQPT] = [RV] * [QI] + [QRI] = 260sec

Having that said, we currently calculate [OVQPT] (here given as 'switchback'
variable) as ...

  switchback = (idev->mc_qrv + 1) * max_delay

RFC3810, 9.12. says "the [Query Interval] in the last Query received". In
section "9.14. Configuring timers", it is said:

  This section is meant to provide advice to network administrators on
  how to tune these settings to their network. Ambitious router
  implementations might tune these settings dynamically based upon
  changing characteristics of the network. [...]

iv) RFC38010, 9.14.2. Query Interval:

  The overall level of periodic MLD traffic is inversely proportional
  to the Query Interval. A longer Query Interval results in a lower
  overall level of MLD traffic. The value of the Query Interval MUST
  be equal to or greater than the Maximum Response Delay used to
  calculate the Maximum Response Code inserted in General Query
  messages.

I assume that was why switchback is calculated as is (3 * max_delay), although
this setting seems to be meant for routers only to configure their [QI]
interval for non-default intervals. So usage here like this is clearly wrong.

Concluding, the current behaviour in IPv6's multicast code is not conform
to the RFC as switch back is calculated wrongly. That is, it has a too small
value, so MLDv2 hosts switch back again to MLDv2 way too early, i.e. ~30secs
instead of ~260secs on default.

Hence, introduce necessary helper functions and fix this up properly as it
should be.

Introduced in 06da92283 ("[IPV6]: Add MLDv2 support."). Credits to Hannes
Frederic Sowa who also had a hand in this as well. Also thanks to Hangbin Liu
who did initial testing.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-04 14:53:20 -04:00
YOSHIFUJI Hideaki
6e7cb83707 ipv6 mcast: Introduce include/net/mld.h for MLD definitions.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2010-04-23 13:35:55 +09:00