This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
- FIFO event channels. Key advantages: support for over 100,000 events (2^17),
16 different event priorities, improved fairness in event latency through
the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with paravirtualized
disk and network, paravirtualized interrupts and timers, no emulated devices
of any kind (and thus no qemu), no BIOS or legacy boot — but instead of
requiring PV MMU, it uses the HVM hardware extensions to virtualize the
pagetables, as well as system calls and other privileged operations."
(from "The Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4BmLAAoJEFjIrFwIi8fJ4SAH/iNGESowgMhfW64vRA8pBWq+
NRJpUjYjjwmbxpwoNl6NPwn15cIXFyc3sMtvvrDD3taRDyko2RFuT+NTjpO05xPh
d/cRpRXpXERHoiFgPf/WTp7ONBDhvPtHG0+BzJKwgqEIOUYXdbhD+gEjaVlFJScS
CAY68OLmk7XYMSZBNzPfKNbSCyhVgZF7wpaimK9lxZBKsFRCDIq6jIyrAsC8epIL
6V/V4l2S6lk/uUeGB6ULphYeINjI2kkpbSfCd1vyenLfWpVscc2o8uWEYFcZMAxy
V4HpsoseuqrfdDqgPfud3VgogdISvbkCvDfW85rzfDP4MWxei2mVHFtJ/gSBV+g=
=ToNG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
* pci/locking:
PCI: Check parent kobject in pci_destroy_dev()
xen/pcifront: Use global PCI rescan-remove locking
powerpc/eeh: Use global PCI rescan-remove locking
MPT / PCI: Use pci_stop_and_remove_bus_device_locked()
platform / x86: Use global PCI rescan-remove locking
PCI: hotplug: Use global PCI rescan-remove locking
pcmcia: Use global PCI rescan-remove locking
ACPI / hotplug / PCI: Use global PCI rescan-remove locking
ACPI / PCI: Use global PCI rescan-remove locking in PCI root hotplug
PCI: Add global pci_lock_rescan_remove()
If pci_stop_and_remove_bus_device() is run concurrently for a device and
its parent bridge via remove_callback(), both code paths attempt to acquire
pci_rescan_remove_lock. If the child device removal acquires it first,
there will be no problems. However, if the parent bridge removal acquires
it first, it will eventually execute pci_destroy_dev() for the child
device, but that device object will not be freed yet due to the reference
held by the concurrent child removal. Consequently, both
pci_stop_bus_device() and pci_remove_bus_device() will be executed for that
device unnecessarily and pci_destroy_dev() will see a corrupted list head
in that object. Moreover, an excess put_device() will be executed for that
device in that case which may lead to a use-after-free in the final
kobject_put() done by sysfs_schedule_callback_work().
To avoid that problem, make pci_destroy_dev() check if the device's parent
kobject is NULL, which only happens after device_del() has already run for
it. Make pci_destroy_dev() return immediately whithout doing anything in
that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between the Xen pcifront device
addition and removal and the generic PCI device addition and removal that
can be triggered via sysfs.
To avoid those race conditions make the Xen pcifront code use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When doing a function/slot/bus reset PCI grabs the device_lock for each
device to block things like suspend and driver probes, but call paths exist
where this lock may already be held. This creates an opportunity for
deadlock. For instance, vfio allows userspace to issue resets so long as
it owns the device(s). If a driver unbind .remove callback races with
userspace issuing a reset, we have a deadlock as userspace gets stuck
waiting on device_lock while another thread has device_lock and waits for
.remove to complete. To resolve this, we can make a version of the reset
interfaces which use trylock. With this, we can safely attempt a reset and
return error to userspace if there is contention.
[bhelgaas: the deadlock happens when A (userspace) has a file descriptor for
the device, and B waits in this path:
driver_detach
device_lock # take device_lock
__device_release_driver
pci_device_remove # pci_bus_type.remove
vfio_pci_remove # pci_driver .remove
vfio_del_group_dev
wait_event(vfio.release_q, !vfio_dev_present) # wait (holding device_lock)
Now B is stuck until A gives up the file descriptor. If A tries to acquire
device_lock for any reason, we deadlock because A is waiting for B to release
the lock, and B is waiting for A to release the file descriptor.]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between PCI hotplug and the generic
PCI bus rescan and device removal that can be triggered via sysfs.
To avoid those race conditions make PCI hotplug use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between the ACPI-based PCI hotplug
(ACPIPHP) and the generic PCI bus rescan and device removal that can be
triggered via sysfs.
To avoid those race conditions make the ACPIPHP code use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are multiple PCI device addition and removal code paths that may be
run concurrently with the generic PCI bus rescan and device removal that
can be triggered via sysfs. If that happens, it may lead to multiple
different, potentially dangerous race conditions.
The most straightforward way to address those problems is to run
the code in question under the same lock that is used by the
generic rescan/remove code in pci-sysfs.c. To prepare for those
changes, move the definition of the global PCI remove/rescan lock
to probe.c and provide global wrappers, pci_lock_rescan_remove()
and pci_unlock_rescan_remove(), allowing drivers to manipulate
that lock. Also provide pci_stop_and_remove_bus_device_locked()
for the callers of pci_stop_and_remove_bus_device() who only need
to hold the rescan/remove lock around it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Consistently use the:
#ifdef CONFIG_PCI_FOO
int pci_foo(...);
#else
static inline int pci_foo(...) { return -1; }
#endif
pattern, instead of sometimes using "#ifndef CONFIG_PCI_FOO".
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aer:
PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0
ACPICA: Add helper macros to extract bus/segment numbers from HEST table.
In the discussion for this set of patches [link below], Bjorn Helgaas
pointed out that the ACPI HEST AER error sources do not have the PCIe
segment number associated with the bus. I worked with the ACPI spec and
got this change to definition of the "Bus" field into the recently released
ACPI Spec 5.0a section 18.3.2.3-5:
Identifies the PCI Bus and Segment of the device. The Bus is encoded in
bits 0-7. For systems that expose multiple PCI segment groups, the
segment number is encoded in bits 8-23 and bits 24-31 must be zero. For
systems that do not expose multiple PCI segment groups, bits 8-31 must be
zero. If the GLOBAL flag is specified, this field is ignored.
This patch makes use of the new definition in the only place in the kernel
that uses the acpi_hest_aer_common's bus field.
This depends on 36f3615152 ("ACPICA: Add helper macros to extract
bus/segment numbers from HEST table.")
Link: http://lkml.kernel.org/r/1370542251-27387-1-git-send-email-betty.dall@hp.com
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well. Compile tested only.
This stops exporting the following interfaces to modules:
pci_target_state()
pci_load_saved_state()
[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This removes this unused and deprecated interface:
alloc_pci_dev()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of f46753c5e3 ("PCI: introduce pci_slot") and
d25b7c8d6b ("PCI: rename pci_update_slot_number to pci_renumber_slot"),
removing this interface:
pci_renumber_slot()
[bhelgaas: split to separate patch, add historical link from Alex]
Link: http://lkml.kernel.org/r/20081009043140.8678.44164.stgit@bob.kio
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Chiang <achiang@canonical.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of 3e1b16002a ("ACPI/PCI: PCIe ASPM _OSC support
capabilities called when root bridge added"), removing this interface:
pcie_aspm_enabled()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andrew Patterson <andrew.patterson@hp.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts db5679437a ("PCI: add interface to set visible size of
VPD"), removing this interface:
pci_vpd_truncate()
[bhelgaas: split to separate patch, also remove prototype from pci.h]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts b48d4425b6 ("PCI: add ID-based ordering enable/disable
support"), removing these interfaces:
pci_enable_ido()
pci_disable_ido()
[bhelgaas: split to separate patch, also remove prototypes from pci.h]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts 48a92a8179 ("PCI: add OBFF enable/disable support"),
removing these interfaces:
pci_enable_obff()
pci_disable_obff()
[bhelgaas: split to separate patch, also remove prototypes from pci.h]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts 51c2e0a7e5 ("PCI: add latency tolerance reporting
enable/disable support"), removing these interfaces:
pci_enable_ltr()
pci_disable_ltr()
pci_set_ltr()
[bhelgaas: split to separate patch, also remove prototypes from pci.h]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
* pci/resource:
PCI: Allocate 64-bit BARs above 4G when possible
PCI: Enforce bus address limits in resource allocation
PCI: Split out bridge window override of minimum allocation address
agp/ati: Use PCI_COMMAND instead of hard-coded 4
agp/intel: Use CPU physical address, not bus address, for ioremap()
agp/intel: Use pci_bus_address() to get GTTADR bus address
agp/intel: Use pci_bus_address() to get MMADR bus address
agp/intel: Support 64-bit GMADR
agp/intel: Rename gtt_bus_addr to gtt_phys_addr
drm/i915: Rename gtt_bus_addr to gtt_phys_addr
agp: Use pci_resource_start() to get CPU physical address for BAR
agp: Support 64-bit APBASE
PCI: Add pci_bus_address() to get bus address of a BAR
PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev
PCI: Change pci_bus_region addresses to dma_addr_t
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts parts of c320b976d7 ("PCI: Add implementation for PRI
capability"), removing these interfaces:
pci_pri_enabled()
pci_pri_stopped()
pci_pri_status()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Joerg Roedel <joro@8bytes.org>
Per the SR-IOV spec rev 1.1:
3.4.1.9 Header Type (Offset 0Eh)
"... For VFs, this register must be RO Zero."
Unfortunately some devices get this wrong, ex. Emulex OneConnect 10Gb NIC.
When they do it makes us handle ACS testing and therefore IOMMU groups as
if they were actual multifunction devices and require ACS capabilities to
make sure there's no peer-to-peer between functions. VFs are never
traditional multifunction devices, so simply clear this bit before we get
any further into setup.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=68431
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Try to allocate space for 64-bit BARs above 4G first, to preserve the space
below 4G for 32-bit BARs. If there's no space above 4G available, fall
back to allocating anywhere.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1387485843-17403-2-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When allocating space for 32-bit BARs, we previously limited RESOURCE
addresses so they would fit in 32 bits. However, the BUS address need not
be the same as the resource address, and it's the bus address that must fit
in the 32-bit BAR.
This patch adds:
- pci_clip_resource_to_region(), which clips a resource so it contains
only the range that maps to the specified bus address region, e.g., to
clip a resource to 32-bit bus addresses, and
- pci_bus_alloc_from_region(), which allocates space for a resource from
the specified bus address region,
and changes pci_bus_alloc_resource() to allocate space for 64-bit BARs from
the entire bus address region, and space for 32-bit BARs from only the bus
address region below 4GB.
If we had this window:
pci_root HWP0002:0a: host bridge window [mem 0xf0180000000-0xf01fedfffff] (bus address [0x80000000-0xfedfffff])
we previously could not put a 32-bit BAR there, because the CPU addresses
don't fit in 32 bits. This patch fixes this, so we can use this space for
32-bit BARs.
It's also possible (though unlikely) to have resources with 32-bit CPU
addresses but bus addresses above 4GB. In this case the previous code
would allocate space that a 32-bit BAR could not map.
Remove PCIBIOS_MAX_MEM_32, which is no longer used.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1386658484-15774-3-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bus_alloc_resource() avoids allocating space below the "min" supplied
by the caller (usually PCIBIOS_MIN_IO or PCIBIOS_MIN_MEM). This is to
protect badly documented motherboard resources. But if we're allocating
space inside an already-configured PCI-PCI bridge window, we ignore "min".
See 688d191821 ("pci: make bus resource start address override minimum IO
address").
This patch moves the check to make it more visible and simplify future
patches. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds pci_enable_msi_range(), which supersedes the pci_enable_msi()
and pci_enable_msi_block() MSI interfaces.
It also adds pci_enable_msix_range(), which supersedes the
pci_enable_msix() MSI-X interface.
The old interfaces have three categories of return values:
negative: failure; caller should not retry
positive: failure; value indicates number of interrupts that *could*
have been allocated, and caller may retry with a smaller request
zero: success; at least as many interrupts allocated as requested
It is error-prone to handle these three cases correctly in drivers.
The new functions return either a negative error code or a number of
successfully allocated MSI/MSI-X interrupts, which is expected to lead to
clearer device driver code.
pci_enable_msi(), pci_enable_msi_block() and pci_enable_msix() still exist
unchanged, but are deprecated and may be removed after callers are updated.
[bhelgaas: tweak changelog]
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Device drivers can use this interface to obtain the maximum number of MSI
interrupts the device supports and use that number, e.g., in a subsequent
call to pci_enable_msi_block().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Convert pci/ioapic.c to be builtin only, with no module option, so we can
support IO-APIC hotplug. Also make it depend on X86_IO_APIC.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
CC: stable@vger.kernel.org
Fix indent code style and replace 'MSI interrupt controller' of comment
with 'MSI controller' to fix the following checkpatch issues:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use max_t() instead of max(resource_size_t,) in order to fix
the following checkpatch warning.
WARNING: max() should probably be max_t(resource_size_t, SZ_64K, size)
WARNING: max() should probably be max_t(resource_size_t, SZ_1M, size)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The mvebu PCI host controller driver uses an emulated PCI-to-PCI bridge to
leverage the core PCI kernel enumeration logic to dynamically create and
remove the MBus windows needed to access the memory and I/O regions of each
PCI interface.
In the context of this PCI-to-PCI bridge emulation, the driver emulates
all reads and writes to the PCI bridge registers. Upon a write to the
registers configuring the I/O base and limit, the driver was creating the
MBus window and calling pci_ioremap_io() to setup the mapping.
However, it turns out that accesses to these registers are made in an IRQ
disabled context, while pci_ioremap_io() is a potentially sleeping
function. Not only this is wrong, but it is causing fairly loud warnings
at boot time when the appropriate kernel hacking options are enabled.
This patch solves this by moving the pci_ioremap_io() call to the startup
of the driver. At this point, we don't know how many PCI interfaces will
be enabled, so we are simply remapping the entire PCI I/O space to virtual
addresses. This is reasonable since this I/O space is limited to 1 MB in
size, and also because the MBus windows continue to be created in a dynamic
fashion only when devices need them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit d2e5f0c16a (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.
Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them. The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.
Fixes: d2e5f0c16a (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021
Reported-and-tested-by: Agustin Barto <abarto@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
